P2905-1 WAK15 WAK15 Wendeplatten - Walter Tools
Take advantage of the combination of a grade optimised for non‑ferrous machining, a low‑adhesion cutting geometry and the proven Walter N‑series to maintain consistent surface quality and efficient chip evacuation; order directly via Metav Werkzeuge or consult the team for application advice. P2905-1 WAK15 Fräswendeschneidplatte — uncoated carbide insert for aluminium milling by Walter Tools The P2905-1 WAK15 is an indexable milling insert designed for efficient machining of aluminium and other non‑ferrous metals, offering sharp cutting edges and geometry tailored to reduce material adhesion. Walter N‑grade WAK15 for aluminium milling Uncoated carbide for sharp cutting edges Low‑adhesion geometry reduces build‑up Part of the Walter N‑Sortensystem Consistent performance for aluminium and non‑ferrous metals The WAK15 grade is an uncoated carbide developed specifically for the ISO N group, meaning it is intended for aluminium and related non‑ferrous materials. The result is a cutting behaviour that targets minimal material adhesion: the combination of sharp cutting edges and a low‑adhesion geometry reduces built‑up edge formation, which in turn supports more reliable surface finish and repeatable part quality. For production environments where small variations in material stickiness can cause rework, this insert offers a technically clear advantage. Stable chip formation and controlled evacuation Equipped with chipbreaker 1, this indexable insert promotes predictable chip control during milling operations, which benefits both tool life and process stability. The defined chipforming characteristics help avoid long, stringy chips on soft, ductile materials and contribute to secure evacuation from the cutting zone. Because chip behaviour is a direct factor in cycle reliability, the insert’s geometry and chipbreaker design help to reduce machine interruptions and lower the risk of part damage during continuous runs. Practical integration in toolsets and machining concepts As part of the Walter N‑Sortensystem, this insert integrates into standard milling toolholders and cutting tool concepts used for non‑ferrous machining. The indexable insert format enables rapid index changes and consistent edge positioning, simplifying tool handling and reducing set‑up time. Where application clarity is needed, the grade designation and series affiliation provide straightforward selection guidance for operations that demand efficient, economical removal of aluminium and similar alloys. For application guidance on the Walter Tools P2905-1 WAK15 and to discuss suitability for specific aluminium machining tasks, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for prompt technical assistance and ordering. Technical data Article number: P2905-1-WAK15-WALTER Name: Fräswendeschneidplatte P2905-1 WAK15 Manufacturer: Walter Tools Facts Chipbreaker: 1 Material code: N Special features Uncoated carbide grade WAK15 Designed for aluminium and non‑ferrous metals Series: Walter N‑Sortensystem Product type: Indexable milling insert FAQ What materials is this insert suitable for? The P2905-1 WAK15 insert is designed for aluminium and other non‑ferrous metals such as copper and brass; the WAK15 grade targets ISO N applications. How does the WAK15 grade prevent material build‑up? WAK15 uses a combination of sharp cutting edges and a low‑adhesion geometry that reduces material sticking, helping the insert maintain surface quality during aluminium milling. Can this insert be used in standard milling holders? Yes, the insert is an indexable milling insert compatible with holders designed for the P2905‑1 family and benefits from the Walter N‑Sortensystem’s standardised fit and indexing. What chip control can be expected with this geometry? With chipbreaker 1, predictable chip formation and controlled evacuation are achieved, reducing interruptions and improving process stability when machining non‑ferrous alloys. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. There is no affiliation between our company and the mentioned brands. The offered item is original and brand‑new from the manufacturer Walter Tools.
P2905-1 WHH15X WHH15X Wendeplatten - Walter Tools
High process reliability and stable chip formation make the P2905-1 WHH15X a cost-effective choice for productive milling; the coated carbide grade extends tool life and supports a broad range of machining tasks. Purchase and application advice available through Metav Werkzeuge for direct supply or specialist consultation. P2905-1 WHH15X milling indexable insert – WHH15X coated carbide, Walter Tools The P2905-1 WHH15X is a coated carbide milling indexable insert engineered for productive milling operations where consistent chip control and durable cutting edges are required. Coated carbide grade WHH15X Designed for productive milling Optimised chip control – chipbreaker 1 Walter cutting grade – open series Reliable performance for productive milling The insert is built on a coated carbide substrate that balances wear resistance and toughness to deliver stable chip formation and prolonged service intervals. As an indexable insert, it permits rapid index changes and minimal machine downtime, translating into higher overall productivity. The WHH15X grade is part of Walter’s open series of cutting grades and is formulated to provide reliable performance across many standard milling tasks; the matrix of suitability should be checked against specific workpiece materials to ensure optimal results. Secure process behaviour and material flexibility With an integrated chipbreaker 1, the geometry supports controlled chip evacuation, reducing the risk of re-cutting and improving surface quality in continuous milling passes. This design choice enhances process security and makes the insert suitable for stable, medium-duty milling strategies. Benefits include more consistent cycle times and reduced secondary operations. For operations where repeatable surface finish and throughput matter, the combination of grade and chipformer supports predictable machining behaviour and easier parameter set-up. Practical selection and integration into production Selection of the correct grade and geometry is important: check the product matrix for the WHH15X grade to confirm compatibility with the intended material and cutting conditions. When integrated into a suitable tool holder system, the insert contributes to repeatable results and predictable maintenance intervals. Edge life and reconditioning intervals depend on speed, feed and cooling strategy; the coated substrate aims to extend wear resistance while preserving cutting-edge integrity for longer productive runs. Contact Metav Werkzeuge to discuss the WHH15X coated carbide grade and confirm suitability for specific materials and milling applications Technical Data Article number: P2905-1-WHH15X-WALTER Product: milling indexable insert Manufacturer: Walter Tools Grade: WHH15X Series: Walter cutting grade - open series Material: catalogue dependent Chipbreaker: 1 Core data Chipbreaker: 1 SKU: P2905-1-WHH15X-WALTER Special features Coated carbide grade (WHH15X) Optimised chipformer, chipbreaker 1 Series: Walter cutting grade - open series Suitability: check product matrix for material selection FAQ What does the WHH15X grade mean for machining performance? The WHH15X grade denotes a coated carbide cutting grade from Walter Tools designed to balance wear resistance and toughness; the WHH15X grade aims to deliver extended tool life and steady performance under typical milling conditions. Which applications are recommended for this insert? This milling indexable insert is intended for general productive milling tasks where controlled chip evacuation and consistent surface quality are required; check the WHH15X product matrix for specific material recommendations. How does chipbreaker 1 affect chip control? Chipbreaker 1 provides a defined chipforming geometry that promotes short, manageable chips in many milling operations, improving evacuation and process security during continuous cuts. Is the insert suitable for hardened materials? Suitability for hardened or specific high-alloy materials is determined by the product matrix; the WHH15X coated carbide is designed for broad application, but compatibility should be verified against the intended workpiece hardness. Can the insert be used in standard tool holders? Yes, the P2905-1 WHH15X indexable insert is compatible with common milling tool holder systems designed for the corresponding insert shape and clamping method; ensure correct seating and torque when installing. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is an original, factory-new product of the manufacturer Walter Tools.
P2905-1 WK10 WK10 Wendeplatten - Walter Tools
Benefit from a combination of uncoated carbide WK10 and optimised chip control for consistent milling performance and predictable tool life; order the insert directly via Metav Werkzeuge or consult Metav Werkzeuge if material suitability needs clarification. P2905-1 WK10 milling indexable insert by Walter Tools — uncoated carbide, open series The P2905-1 WK10 is a milling indexable insert engineered for general-purpose and finishing operations where a reliable, uncoated cemented carbide grade and straightforward chip control are prioritised; material compatibility should be checked against the product matrix. Uncoated cemented carbide WK10 grade Open series for broad material range Optimised chip control design Stable cutting-edge formation Consistent machining with an uncoated carbide grade The insert is manufactured from an uncoated cemented carbide grade that provides a stable cutting edge and predictable wear behaviour. This metallurgy reduces thermal sensitivity during interrupted cuts and supports consistent dimensional accuracy over life cycles. By combining material robustness with a simple, open-grade concept, the insert delivers reliable performance across a variety of machining tasks. The WK10 grade is intended for broad applications; final selection should rely on the product matrix to confirm suitability for specific workpiece materials. Better chip control for safer, productive milling An optimised chipbreaker (chipbreaker 1) ensures controlled chip formation under typical cutting conditions, reducing the risk of built-up edge and improving swarf evacuation. Better chip control translates directly into fewer tool changes and shorter cycle times, which raises productivity on the shop floor. The insert’s geometry is designed to maintain a stable cutting edge, supporting repeatable surface finish and process stability even when run lengths vary. Practical guidance for integration and selection The insert is part of the Walter Schneidstoffsorte — open series, allowing straightforward grade selection in general machining programmes. For integration into existing toolholders, verify seat compatibility with the designation P2905-1 WK10 and review the product matrix to determine the best cutting parameters. Where uncertain, consult technical documentation or request a cutting-data sheet to match speeds and feeds to the grade and workpiece material; this step ensures the combination of tool, insert and process yields the intended economy and component quality. Contact Metav Werkzeuge for tailored advice on selecting the Walter Tools P2905-1 WK10 milling insert; eMail info@metav-werkzeuge.com or call +49 2822 7131930 for precise grade-pairing and stock availability Technical Data SKU: P2905-1-WK10-WALTER Designation: P2905-1 WK10 Article name: Fräswendeschneidplatte / milling indexable insert Brand: Walter Tools Material: Katalogabhängig Core specifications Chipbreaker: 1 Special features Grade: WK10 Series: Walter Schneidstoffsorte - Serie offen Substrate: uncoated cemented carbide ISO designation: P2905-1 WK10 UID: P2905-1-WK10-WALTER FAQ What material family does this insert suit? Material suitability must be checked against the product matrix; the insert uses an uncoated cemented carbide WK10 grade intended for a broad range of general machining tasks. Is the insert coated or uncoated? The insert is supplied as an uncoated cemented carbide grade (WK10), offering stable cutting-edge behaviour without surface coatings. What does chipbreaker 1 mean for my process? Chipbreaker 1 indicates a geometry focused on controlled chip formation and reliable swarf evacuation, which supports safer, more productive milling cycles. Which series does this insert belong to? This item is part of the Walter Schneidstoffsorte — open series, designed to simplify grade selection across varied applications. How should suitability be verified for a specific alloy? Consult the manufacturer’s product matrix and cutting-data tables to match the WK10 grade to the workpiece alloy and machining parameters before production runs. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names belong to their respective owners. Brand names are used for explanation only and do not imply any affiliation between our company and the named manufacturers. The offered article is original, unused factory-new goods from the manufacturer.
P2905-1 WPM15G WPM15G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a coated carbide grade (WPM15G) and an optimised chipformer to increase tool life and maintain process stability in productive milling operations. Order the P2905-1 WPM15G directly via Metav Werkzeuge or ask our consultants if needed. P2905-1 WPM15G milling insert — Tiger·tec Gold coated (Walter Tools) A P2905-1 WPM15G milling insert designed for productive machining, combining a coated carbide grade with Tiger·tec Gold technology to support stable chip formation and reliable cutting-edge performance. Tiger·tec Gold coating for extended edge life Coated carbide grade WPM15G for reliable wear resistance Optimised chipformer for stable chip control Suited to productive milling applications Consistent performance through advanced coating and grade selection The coated carbide WPM15G belongs to the Tiger·tec Gold series and is manufactured to offer enhanced wear resistance and thermal stability. This composition means that the cutting edge is supported by a robust coating system that reduces flank wear and helps preserve geometry over longer production runs. In practice, fewer insert changes are required, which translates to improved process efficiency and reduced downtime. The underlying carbide and coating combination is explained in the technical matrix and should be matched to the specific workpiece material for optimum results. Reliable chip control and process security for high-output milling Equipped with an optimised chipformer (chipformer 1), the insert promotes controlled chip breaking and evacuation under typical milling conditions. Controlled chip formation reduces the risk of re-cutting and protects toolholders and machine surfaces, which increases overall process security. For abrasive or variable cutting regimes, the stable chip behaviour afforded by this geometry supports consistent surface quality and predictable tool life. Specification checks against the product matrix are recommended to confirm the best operating windows and cutting data for the intended application. Practical advantages for production environments and tool logistics Designed as a production-oriented cutting solution, the insert supports repeatable performance and efficient tool management. The combination of a coated carbide grade and a robust Tiger·tec Gold treatment provides a balance between wear resistance and edge toughness, which benefits both short-run and continuous operations. In addition, standardised designation and series coding simplify tool assembly and reordering, aiding inventory control and reproducible machining results. For tailored application advice or data sheets, Metav Werkzeuge can provide further documentation to align the insert with specific machining tasks. For reliable high-productivity milling with a Tiger·tec Gold grade, specify the P2905-1 WPM15G from Walter Tools and contact Metav Werkzeuge for technical consultation or supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: P2905-1-WPM15G-WALTER Insert designation: P2905-1 WPM15G Series: Tiger·tec Gold Facts Chipformer: 1 Grade: WPM15G Product type: Milling insert Special features Coated carbide grade Optimised chipformer for chip control Material designation: per catalogue Brand: Walter Tools FAQ What materials is this insert suitable for? Suitability depends on the workpiece and cutting conditions; the P2905-1 WPM15G uses a coated carbide grade from the Tiger·tec Gold family, and material compatibility should be verified in the product matrix for correct application. What advantage does the Tiger·tec Gold treatment provide? The Tiger·tec Gold technology enhances wear resistance and thermal stability, supporting longer edge life and consistent surface finish when the correct cutting parameters are applied. Which chipforming behaviour can be expected with this insert? With chipformer 1, controlled chip breaking and evacuation are promoted, improving chip control and contributing to stable machining cycles. Is this insert intended for high-productivity milling? Yes, the design and coating strategy target productive milling operations where process stability and repeatable tool life are priorities. How is the insert designated and how to check holder compatibility? The designation is P2905-1 WPM15G; compatibility with specific toolholders should be confirmed against the holder manufacturer’s specifications and the product matrix. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for descriptive purposes and do not imply any affiliation or endorsement by the trademark holders. The offered article is an original, factory-new product of the manufacturer.
P3201-D07.94 WHH15X Wendeplatten - Walter Tools
Benefit from the combination of a coated carbide grade (WHH15X) and the D07.94 chipbreaker for controlled chip formation and consistent milling performance; order or request application guidance via Metav Werkzeuge for a reliable production result. P3201-D07.94 WHH15X indexable milling insert – D07.94 chipbreaker, coated carbide (Walter Tools) The P3201-D07.94 WHH15X is an indexable milling insert developed for general milling operations where controlled chip flow and repeatable performance are essential, suitable for machining tasks that require reliable chip control and stable edge behaviour. Coated carbide grade WHH15X D07.94 chipbreaker for stable chips Designed for productive milling operations Consistent performance through optimised chip control The combination of a D07.94 chipbreaker and a coated carbide grade provides a dependable basis for predictable chip formation, which reduces interruptions and improves cycle stability. Stable chips lower the risk of tool clashes and make process planning more reliable. For production environments, this results in fewer unplanned stops and a more even tool load distribution, contributing to overall productivity gains. Improved tool life and surface quality A coated hardmetal grade such as WHH15X is selected to balance wear resistance and toughness; this helps to extend tool life while preserving a consistent surface finish on machined components. The coating reduces flank wear under many cutting conditions, which supports longer intervals between index changes and contributes to lower process costs over time without compromising part quality. Suitable for varied milling tasks — check the application matrix The insert grade and chipbreaker are intended for a broad range of milling applications, but specific material suitability must be verified in the product matrix. The grade is a coated carbide type; therefore, confirmation of compatibility with specific alloys or hardened materials is recommended before series production. Where uncertainty exists, technical documentation or a material-specific recommendation should be consulted. Integration and usage in existing tool systems The insert designation aligns with standard indexable milling systems and can be fitted into compatible milling cutters that accept this geometry. Correct seating and the use of recommended clamping torques ensure repeatable positioning and safe operation. For retrofitting or new tool assemblies, confirmation of seat geometry and cutter compatibility is advised to guarantee optimal cutting conditions. Economic benefits for production workflows By reducing unscheduled downtime through controlled chip evacuation and improved wear behaviour, the insert supports a more cost-effective machining process. The WHH15X grade aims to provide a reliable compromise between cutting-edge durability and economic performance, which can result in lower total cost per component in medium to high-volume milling operations. Manufacturer standards and traceability The insert belongs to the Walter series of coated carbide grades and is identified as an indexable milling insert with designation D07.94. Traceable article codes and standardised grade nomenclature simplify reordering and quality assurance in production environments, helping to maintain consistent tool sets across multiple machines. Contact Metav Werkzeuge for tailored application advice on the Walter Tools P3201-D07.94 WHH15X insert or to request the detailed material compatibility matrix via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: P3201-D07.94-WHH15X-WALTER Product name: P3201-D07.94 WHH15X Walter Tools Product type: Indexable milling insert Manufacturer: Walter Tools Designation: P3201-D07.94 Chipbreaker: D07.94 Series: Walter Schneidstoffsorte - Serie offen Facts Grade designation: WHH15X Coating: coated hardmetal (as grade classification) SKU: P3201-D07.94-WHH15X-WALTER Special features Coated carbide grade WHH15X Optimised chip former D07.94 Series classification: open grade series Intended use: milling / indexable insert applications Note: verify material suitability in product matrix FAQ What applications is this insert intended for? The insert is designed for general milling applications where controlled chip formation is required; the P3201-D07.94 WHH15X grade is suitable for a range of machining tasks, with final suitability determined by the product matrix. How does the D07.94 chipbreaker affect machining? The D07.94 chipbreaker promotes stable chip formation and easy chip evacuation, which helps to reduce interruptions and supports consistent surface finishes when using the WHH15X coated carbide grade. Is the WHH15X grade suitable for hardened materials? Material compatibility must be checked in the detailed product matrix; WHH15X is a coated carbide grade and may be suitable for many alloys, but verification is necessary for pre‑hardened or high‑hardness steels. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Walter Tools is part of the Walter group. Trademarks and trade names are the property of their respective owners. The mentioned brand names are used for description and identification only. The offered item is an original, factory‑new product of the manufacturer.
P3201-D08 WHH15X Wendeplatten - Walter Tools
Benefit from the combination of a WHH15X coated carbide grade and a D08 chipbreaker for reliable chip control and productive milling; order original Walter Tools inserts directly via Metav Werkzeuge or consult our specialists for application advice. P3201-D08 WHH15X milling indexable insert – D08 chipbreaker, coated carbide (Walter Tools) The P3201-D08 WHH15X is a coated carbide milling insert intended for general milling operations where reproducible chip formation and process stability are required Coated carbide WHH15X grade D08 chipbreaker for stable chips Designed for productive milling Original Walter Tools quality Increased productivity through controlled chip formation The insert is engineered to deliver consistent chip control via the D08 chipbreaker, which guides the chips into predictable shapes and lengths. This reduces tool interference and helps to maintain uninterrupted machining cycles, improving cycle times and uptime. The WHH15X coated carbide composition combines wear resistance with a reliable cutting edge, so the insert sustains performance across repetitive operations. For planners and process engineers, the D08 geometry translates into fewer stoppages and more uniform machining results, particularly in mixed-batch production where repeatability is critical. Repeatable surface quality and process stability Coating technology on the grade reduces flank wear and supports stable cutting-edge life, resulting in more consistent surface finishes over long series production. The protective coating lowers friction and thermal load at the cutting zone, which limits edge deterioration and preserves dimensional accuracy. Material suitability should be verified against the manufacturer’s product matrix, since the open-grade series requires selection according to the workpiece material and cutting conditions. Where matrix guidance is followed, the insert supports dependable part quality and predictable tool change intervals. Seamless integration into existing tool systems The insert’s designation and geometry are aligned with common milling toolholders, enabling straightforward retrofitting into established setups. Its type designation simplifies inventory management and traceability within toolrooms and manufacturing planning systems. Application specialists and production engineers will appreciate the compatibility with standard clamping systems and the ability to apply the insert across a range of peripheral milling tasks. For detailed selection, reference the product matrix and mounting specifications to ensure the correct fit and optimal cutting parameters for the intended operation. Contact Metav Werkzeuge for tailored application advice and availability of original Walter Tools P3201-D08 WHH15X milling inserts; eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: P3201-D08-WHH15X-WALTER Designation: P3201-D08 WHH15X Product type: Milling indexable insert Manufacturer: Walter Tools Core specifications Grade: WHH15X Chipbreaker: D08 Series: Walter coated carbide — open series Type designation: P3201-D08 Special features Coated carbide grade WHH15X Catalogue-dependent material information Intended for productive general milling Original Walter Tools design FAQ What materials is this insert suitable for? The WHH15X grade is a coated carbide used in general milling; material suitability for the P3201-D08 WHH15X insert should be checked against the manufacturer’s product matrix to match the workpiece material and operating conditions. What is the purpose of the D08 chipbreaker? The D08 chipbreaker on this insert promotes controlled chip formation and evacuation, which supports uninterrupted machining cycles and reduces the risk of chip-related interruptions in milling operations. How is the insert identified for stock and ordering? Identification is via the type designation P3201-D08 WHH15X and SKU P3201-D08-WHH15X-WALTER; these references simplify inventory control and reordering of the original Walter Tools insert. Can the insert maintain surface quality over long production runs? When used within the recommended cutting parameters and with material suitability verified, the coated WHH15X grade supports stable cutting-edge life and consistent surface finish across series production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used solely for explanatory purposes and do not imply any affiliation with our company. The offered item is an original, factory-new product from the manufacturer.
P3201-D09.52 WHH15X Wendeplatten - Walter Tools
The combination of a coated carbide grade and a dedicated chipbreaker D09.52 delivers reliable chip control and consistent surface quality in general milling. The design of the insert supports versatile milling tasks across many tool platforms while keeping tool changes and inventory straightforward. Order the P3201-D09.52 WHH15X milling indexable insert directly via Metav Werkzeuge or ask our consultants if needed. P3201-D09.52 WHH15X – Milling indexable insert with D09.52 chipbreaker by Walter Tools The P3201-D09.52 WHH15X is a coated carbide milling indexable insert intended for versatile milling operations; suitability for specific workpiece materials should be checked against the product matrix. Coated carbide grade WHH15X Chipbreaker D09.52 for controlled chips Open-series for versatile milling Walter Tools precision and stability Stable chip control for predictable production The insert’s central advantage is consistent chip formation created by the chipbreaker D09.52, which reduces the risk of long, tangled chips and supports uninterrupted machining. In practice, reliable chip control lowers cycle-time variability and simplifies chip evacuation in both small-batch and continuous production. The chipbreaker geometry is designed to produce short, manageable swarf, which aids downstream handling and improves operator safety. This predictable behaviour translates to fewer interruptions and a steadier process window. Coated carbide formulation that balances wear resistance and economy The WHH15X grade is a coated carbide variety aimed at productive milling across a broad range of applications; it offers a compromise between wear resistance and cost-effectiveness. Coating improves edge life by protecting the substrate against abrasion and thermal effects during intermittent milling. For production planners, this means longer intervals between index changes and more predictable tool life—advantages that support a controlled cost-per-part calculation. Where high-speed conditions or demanding geometries occur, checking the product matrix for optimal grade selection is advised. Versatility and simple integration into milling systems The insert is part of an open series, designed for flexible use on many standard milling tool families. The geometric code indicates suitability for a variety of pocket types and clamping systems; the insert can therefore streamline inventory by fitting multiple cutter bodies. Engineers will value the easy match to common toolholders and the straightforward interchangeability that reduces setup time. For those managing tool stocks, this adaptability contributes directly to higher machine utilisation and reduced planning complexity. Practical guidance for application and process security Application suitability should be verified with the manufacturer’s product matrix to ensure the grade matches the workpiece material and cutting parameters. When planning a new operation, consider the insert’s chipbreaker performance together with feed and speed settings to reach the targeted surface finish and dimensional stability. For best results, pair the insert with a rigid holder and monitor cut depths to maintain the integrity of the cutting edge. Documentation and test cuts remain the most reliable method to confirm performance in a specific production environment. For application advice or to source the P3201-D09.52 WHH15X insert from Metav Werkzeuge, contact Metav Werkzeuge for tailored recommendations and availability Technical Data Article number: P3201-D09.52-WHH15X-WALTER Product designation: P3201-D09.52 WHH15X Type: Milling indexable insert Brand: Walter Tools Facts Chipbreaker: D09.52 Grade / Sort: WHH15X Series: Walter Schneidstoffsorte - Serie offen Material: Katalogabhängig SKU / UID: P3201-D09.52-WHH15X-WALTER Special features Coated carbide insert Designed for controlled chip formation Versatile use across standard milling holders Suitable for general milling applications; check product matrix for workpiece compatibility FAQ What is the primary advantage of the D09.52 chipbreaker? The D09.52 chipbreaker on the P3201-D09.52 WHH15X insert promotes short, controllable chips, improving chip evacuation and reducing interruption risk during milling operations. Which materials is the WHH15X grade suitable for? The WHH15X is a coated carbide grade intended for broad use; specific suitability depends on the product matrix, so material matching should be confirmed for each application. Can this insert be used in a variety of milling toolholders? Yes, the open-series design of the insert allows integration with many standard milling cutter systems, simplifying inventory and tool changes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original factory-new goods from the manufacturer.
P3201-D10 WHH15X WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide WHH15X, a D10 chipbreaker and Walter Tools’ proven cutting-edge stability to improve cycle consistency and reduce interruption time. Order directly via Metav Werkzeuge or consult our technical team for machining recommendations. P3201-D10 WHH15X Milling Insert – Coated carbide, D10 chipbreaker by Walter Tools P3201-D10 WHH15X is a precision milling insert designed for general milling and finishing tasks, featuring a D10 chipbreaker and a coated carbide grade suited to a broad range of machining applications Coated carbide grade WHH15X D10 chipbreaker for controlled swarf Open-series grade for broad material range Walter Tools quality and stable cutting edge Higher productivity through consistent cutting performance The combination of coated carbide and a precisely engineered D10 chipbreaker delivers steady metal removal rates and predictable tool life. This indexable plate reduces the frequency of unexpected interruptions by improving chip control and lowering the risk of built-up edge. For production environments where cycle time and repeatability matter, the insert’s design supports higher feed rates with maintained surface integrity. The engineering behind the grade emphasises reliability in varied cutting conditions while helping to keep secondary operations predictable. Reduced downtime with defined chip formation Controlled swarf evacuation is a direct benefit of the D10 chipbreaker, which is optimised to break chips into manageable fragments. This characteristic minimises the need for manual clearing and reduces the probability of chips affecting the workpiece or toolholder. The result is fewer unplanned stoppages and a smoother workflow on the shopfloor. Operators and process planners will find that improved chip behaviour contributes to safer machining, easier coolant flow, and more consistent part quality during extended runs. Versatile grade for a broad material spectrum The WHH15X grade is a coated hardmetal variant intended for flexible application across many materials; compatibility should be verified against the detailed product matrix for specific alloys. This open-series grade is engineered to balance wear resistance and edge robustness, offering an effective compromise between long tool life and reliable cutting for mixed production batches. Where mixed materials are processed, choosing a grade with broad applicability reduces tooling changes and simplifies inventory management. Practical specification and integration benefits Identification and handling are straightforward: the insert is designated P3201-D10 WHH15X and supplied in the Walter Tools series format for straightforward stocking and replacement. The coated substrate supports common clamping and toolholder systems used in milling operations, while the open-series philosophy makes it suitable for adaptable machining strategies. For users requiring deeper technical data or application tables, Metav Werkzeuge can provide the product matrix and practical recommendations to match cutting parameters to the intended workpiece material. For tailored application advice or to check availability of Walter Tools P3201-D10 WHH15X inserts, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or +49 2822 7131930 for expert recommendations and supply options Technical Data SKU: P3201-D10-WHH15X-WALTER Designation: P3201-D10 WHH15X Product type: Milling insert Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Core specifications Chipbreaker: D10 Grade: WHH15X (coated carbide) Article ID: P3201-D10 WHH15X Unique ID: P3201-D10-WHH15X-WALTER Special features Coated hardmetal grade Material information: catalogue-dependent Series: open grade series Sorteneinsatz guidance: check product matrix for material suitability FAQ What applications is this insert best suited for? The P3201-D10 WHH15X milling insert is intended for general milling and finishing tasks where stable cutting and effective chip control are required; consult the product matrix for specific material recommendations. How does the D10 chipbreaker improve machining? The D10 chipbreaker on this Walter Tools insert produces consistent, short chips that improve evacuation, reduce machine interruptions and support safer, more efficient production processes. Is the WHH15X grade suitable for stainless applications? The WHH15X coated carbide grade offers broad applicability; suitability for rostfreier Stahl and other specific alloys should be verified using the product matrix supplied by the manufacturer or Metav Werkzeuge. Where can detailed cutting data and compatibility tables be obtained? Cutting data and the full material compatibility matrix for the P3201-D10 WHH15X are available from Metav Werkzeuge on request to assist in parameter selection and process planning. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned for explanatory purposes only; there is no affiliation between our company and the named manufacturers. The offered item is original, factory-new merchandise of the respective manufacturer.
P3201-D10 WKP25 Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide WKP25, an optimised D10 chipbreaker and broad material compatibility for reliable, productive milling; order the P3201-D10 WKP25 directly via Metav Werkzeuge or consult our specialists for application advice. P3201-D10 WKP25 milling indexable insert – D10 chipbreaker, for steel & cast iron (Walter Tools) A P3201-D10 WKP25 milling indexable insert engineered for productive finishing and roughing of steel and cast iron, featuring a coated carbide grade developed for stable chip formation. Coated carbide grade WKP25 Optimised D10 chipbreaker For steel and cast iron machining Reliable chip control and productivity Increase throughput with stable chip control The insert delivers enhanced cycle times through an optimised D10 chipbreaker that promotes consistent, short chips when machining P- and K-group materials. Designed for diverse milling geometries, the chip control reduces the need for secondary handling and helps maintain steady material removal rates. Where cutter balance and consistent chip evacuation are critical, this grade supports uninterrupted production runs and reduces the risk of workpiece damage from long, stringy swarf. The result is measurable improvement in process efficiency and component quality. Longer tool life from coated carbide technology Built on a coated carbide substrate, the cutting grade WKP25 provides wear resistance suited to the thermal and abrasive demands of machining steel and cast iron. The coating enhances edge stability and helps prevent premature flank wear, so insert change intervals are extended and tool costs per part are reduced. When facing variations in feed or intermittent cuts, the insert's durability contributes to lower tool consumption and fewer unplanned stoppages, supporting predictable maintenance intervals and improved overall equipment effectiveness. Versatile application across common workshop materials The grade is classified for ISO material groups P and K, meaning it is suitable for unalloyed and alloyed steel as well as cast iron, in line with ISO 513 grouping. This versatility makes the insert a pragmatic choice for job shops and production lines handling mixed batches of components. The open series format allows compatibility with a range of cutter geometries; when combined with correct cutting data and coolant strategy, the insert delivers reliable surface finish and repeatable dimensional results for both finishing and semi-finishing operations. Contact Metav Werkzeuge today for tailored advice on integrating Walter Tools P3201-D10 WKP25 inserts into existing milling processes and to secure suitable delivery options Technical data Article number: P3201-D10-WKP25-WALTER Product type: milling indexable insert Designation: P3201-D10 WKP25 Brand: Walter Tools Core specifications Grade: WKP25 Cutting material: coated carbide Chipbreaker: D10 Material groups: P (steel), K (cast iron) — per ISO 513 Series: Walter Schneidstoffsorte - Serie offen Features Suitable for steel machining Suitable for cast iron machining Stable chip formation Designed for productive milling FAQ What materials can this insert machine effectively? The P3201-D10 WKP25 insert from Walter Tools is specified for ISO groups P and K, making it suitable for machining steel and cast iron. What does the D10 chipbreaker achieve? The D10 chipbreaker on the indexable insert promotes controlled, short chips, which improves chip evacuation and reduces the likelihood of surface damage during milling. Is WKP25 a coated grade and what benefit does that provide? Yes, WKP25 is a coated carbide grade; the coating enhances edge robustness and wear resistance, extending tool life under typical steel and cast iron cutting conditions. Which series does this insert belong to and what does that mean for compatibility? The insert is part of the Walter Schneidstoffsorte - Serie offen, which means it is available in an open series suitable for a range of cutter geometries and common milling applications. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is an original, factory-new product of the manufacturer.
P3201-D10 WKP35 WKP35 Wendeplatten - Walter Tools
Take advantage of a productive combination of coated carbide grade WKP35, the D10 chipbreaker for controlled swarf formation, and proven durability across steel and cast iron machining—ensuring stable output and longer tool life. Order the P3201-D10 WKP35 directly via Metav Werkzeuge or contact our consultants for application advice. P3201-D10 WKP35 milling indexable insert, D10 chipbreaker — Walter Tools A P3201-D10 WKP35 milling indexable insert engineered for efficient, high‑productivity machining of steel and cast iron in industrial milling applications Coated carbide grade WKP35 Optimised D10 chipbreaker For steel and cast iron machining High stability and extended tool life Controlled chip formation for consistent productivity The insert delivers reliable chip control through its D10 chipbreaker, designed to break and evacuate swarf effectively during interrupted cuts and variable feed conditions. This stability reduces machine downtime and minimises the risk of rework, supporting a smoother production flow. The chip geometry is matched to common steel and cast iron behaviours defined in ISO 513, so the insert performs predictably across a wide range of ferrous workpieces and typical industrial cutting parameters. Coated carbide grade tuned for durability and wear resistance The WKP35 designation denotes a coated carbide grade optimised for a balance between toughness and abrasive wear resistance. The coating improves thermal stability at the cutting edge and contributes to longer tool life, while the substrate provides sufficient toughness for interrupted machining. For workshop planners and process engineers, this means fewer insert changes, reduced tooling consumption and more consistent component finishes over batch runs. Versatile use across steel and cast iron applications Designed for the ISO material groups P and K, the insert is suitable for unalloyed and alloyed steel as well as cast iron, enabling consolidation of tool inventories where a single grade can address multiple part families. The combination of the WKP35 grade and D10 groove geometry supports both roughing and medium finishing operations, helping to simplify tooling decisions and improve process reliability for repeated production cycles. Practical integration and process benefits The insert form factor P3201-D10 is compatible with common milling toolholders, allowing straightforward retrofit into existing tool assemblies without major changes to clamping or toolpath strategies. When specified in a process sheet, the material compatibility and chipbreaking characteristics reduce the need for application-specific trialling. For operational teams, that translates into predictable cycle times and easier planning of spare parts and maintenance intervals. For process guidance or to specify the right grade for a particular component geometry, contact Metav Werkzeuge for an application consultation and fast supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: P3201-D10-WKP35-WALTER SKU: P3201-D10-WKP35-WALTER Brand: Walter Tools Product type: milling indexable insert ISO designation: P3201-D10 WKP35 Grade: WKP35 Chipbreaker: D10 Material system: coated carbide Facts Compatible material groups: P (steel), K (cast iron) Geometry family: P3201 series Series: Walter Schneidstoffsorte - Serie offen UID: P3201-D10-WKP35-WALTER Special features Coated carbide (beschichtetes Hartmetall) Optimised for stable swarf formation Balanced wear resistance and toughness Suitable for interrupted cuts and variable feeds Application focus: steel and cast iron per ISO 513 FAQ What materials is this insert suitable for? The P3201-D10 WKP35 insert from Walter Tools is suitable for ISO groups P and K, specifically engineered for machining steel and cast iron. What advantage does the D10 chipbreaker provide? The D10 chipbreaker ensures controlled breakage and evacuation of swarf, improving cycle stability and reducing the likelihood of built‑up edge or rework. Is the WKP35 grade suitable for interrupted milling? Yes, the WKP35 coated carbide grade offers a balance of toughness and wear resistance that is well suited to interrupted cuts commonly encountered in milling operations. Can this insert be used in existing milling holders? The P3201-D10 geometry is compatible with common milling toolholders, allowing straightforward integration without major alterations to existing assemblies. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names belong to their respective owners. Brand names and protected designations are mentioned for clarification only. There is no affiliation between our company and the brands named. The offered article is an original, factory‑new product of the manufacturer.
P3201-D12 WHH15X Wendeplatten - Walter Tools
Benefit from the combination of the WHH15X coated-carbide grade and the D12 chipbreaker for stable chip control and long tool life; order the insert directly via Metav Werkzeuge or request product-matrix advice from our consultants. P3201-D12 WHH15X indexable milling insert — D12 chipbreaker, coated carbide (Walter Tools) A P3201-D12 WHH15X indexable milling insert engineered for versatile milling applications, offering stable chip formation and consistent performance in CNC machining. Coated carbide grade WHH15X D12 chipbreaker for stable chips Open series for broad material coverage Consistent cutting performance that reduces downtime The insert delivers predictable wear behaviour through the WHH15X coated-carbide grade, a coated hardmetal designed for a balance of wear resistance and edge stability. This results in longer tool life and fewer insert changes, which lowers machine downtime and increases net throughput. The coating optimises thermal and abrasive resistance; in practical terms, that means more components per insert and a reduced cost per part. For process planners seeking repeatable results, the material and coating combination provides a measurable improvement in cycle consistency. Reliable chip control for cleaner machining and better surface quality The D12 chipbreaker geometry promotes controlled chip formation across a range of cutting conditions, helping to avoid long, stringy chips and minimising secondary operations. Improved chip control reduces toolholder clogging and shortens cycle times by enabling higher uninterrupted feed rates. When combined with correct cutting parameters and coolant strategy, the insert supports enhanced surface finish and lower scrap rates, particularly in operations where chip evacuation is critical. Broad applicability with straightforward integration into existing tool systems As an indexable milling insert from the Walter open series, this grade is intended for versatile use across many common machining tasks — however, material suitability should be verified against the product matrix. The open-series philosophy supports integration with a wide range of cutter bodies and holders, simplifying stock management and reducing the need for multiple specialised grades. Where specific workpiece materials or hardened conditions are to be machined, consult the detailed matrix before finalising tool selection to ensure optimal results. Practical notes for planning and process support The insert is supplied as a standard indexable item with the WHH15X grade and the D12 chipbreaker; process engineers should correlate workpiece material and cutting data with the manufacturer's recommendations. Stable cutting edges and consistent chip formation help ensure predictable cycle times and lower rework. If any doubt exists regarding suitability for a particular alloy or machining strategy, Metav Werkzeuge can provide the product matrix and advise on parameters to match productivity targets. Contact Metav Werkzeuge for tailored advice on applying the Walter Tools P3201-D12 WHH15X indexable milling insert and to request the detailed product matrix and availability Technical data SKU: P3201-D12-WHH15X-WALTER Product type: Indexable milling insert Grade: WHH15X Chipbreaker: D12 Series: Walter Schneidstoffsorte - Serie offen Manufacturer: Walter Tools Core specifications Coating: coated carbide (as per product grade) Material base: hardmetal (coated) Designation: P3201-D12 WHH15X UID: P3201-D12-WHH15X-WALTER Special features Open-series grade for broad material coverage Optimised chip former for consistent chip control Designed for integration with common cutter bodies Material suitability to be checked against the product matrix FAQ Which materials is this insert intended to machine? Material suitability depends on the application matrix; the P3201-D12 WHH15X is a coated carbide grade intended for a broad range of materials, but compatibility must be checked against the manufacturer’s product matrix. How does the D12 chipbreaker affect machining? The D12 chipbreaker provides controlled chip formation, improving chip evacuation and reducing the risk of rework or toolholder obstruction in milling operations. Is the WHH15X grade suitable for high-speed milling? WHH15X is a coated hardmetal grade noted for a balance of wear resistance and stability; cutting speed capability will depend on workpiece material and cutting conditions as listed in the product matrix. Can the insert be used in standard cutter bodies? Yes, the P3201-D12 WHH15X is an indexable milling insert designed for use in common cutter bodies; ensure the chosen holder matches the insert designation and clamping requirements. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned for explanation only; there is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
P3201-D12 WKP25 Wendeplatten - Walter Tools
The combination of the WKP25 coated carbide grade and the D12 chipbreaker delivers stable chip control and reliable edge life for steel and cast iron milling; this reduces downtime and supports consistent surface quality. Order directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. P3201-D12 WKP25 milling insert — Coated carbide, D12 chipbreaker | Walter Tools P3201-D12 WKP25 is a coated carbide milling insert designed for efficient machining of steel and cast iron, offering dependable chip control and repeatable performance in indexable milling applications Coated carbide WKP25 grade Optimised D12 chipbreaker Suited for steel and cast iron Consistent edge life and process security Predictable chip control for efficient milling The P3201-D12 WKP25 insert combines a specifically designed D12 chipbreaker with a coated carbide substrate to control chip form during interrupted and continuous milling. The chipbreaker geometry helps to break and evacuate swarf reliably, which reduces re-cutting and protects the cutting edge. For machining centres and high-volume cell work, this means fewer tool changes and more consistent cycle times. The grade WKP25 is formulated for broad applicability across ISO group P (steel) and K (cast iron), so the insert supports a range of alloyed and unalloyed steels as well as typical cast materials. Durable edge behaviour and process security A coated carbide grade engineered for steady wear resistance, WKP25 offers long-lasting edges under typical milling conditions. The coating improves thermal stability and reduces adhesive wear, which contributes to predictable tool life and improved surface finish on machined parts. This stability increases overall process security, making the insert suitable for production runs where repeatability and low scrap rates are priorities. Where tighter tolerances are required, the consistent performance reduces the need for frequent inspection and adjustment. Practical selection and machining benefits Choosing the right insert geometry and grade simplifies set-up and boosts productivity. The P3201-D12 form factor and the D12 chipbreaker are well suited to general face and shoulder milling operations where controlled chip evacuation is essential. For customers less familiar with chipbreaker functions: the geometry actively shapes the chip so that coolant contact and tool clearance are optimised, lowering the risk of built-up edge. For tailored cutting data or recommendations for specific steel grades and cast iron types, the technical advisors at Metav Werkzeuge can provide parameter guidance based on machining centre capabilities and workpiece specifications. Contact Metav Werkzeuge for application advice, delivery options and to discuss how the Walter Tools P3201-D12 WKP25 milling insert can be integrated into current tool setups Technical data SKU: P3201-D12-WKP25-WALTER Article: P3201-D12 WKP25 Product type: Milling insert (indexable) Facts Grade: WKP25 Chipbreaker: D12 Material group suitability: P / K Special features Coating: coated carbide Series: Walter Schneidstoffsorte - Serie offen Geometry designation without grade: P3201-D12 Suitable for: steel, cast iron FAQ What materials is the P3201-D12 WKP25 suitable for? The P3201-D12 WKP25 insert is intended for ISO group P (steel) and K (cast iron) machining and performs well across a range of alloyed and unalloyed steels and common cast materials. How does the D12 chipbreaker improve machining performance? The D12 chipbreaker shapes and fractures chips to improve evacuation and reduce re-cutting; when used with the WKP25 coated carbide grade, it supports stable tool life and improved surface quality. Is the insert compatible with standard milling toolholders? The P3201-D12 form is a standard indexable insert shape compatible with matching milling cutter bodies and toolholders designed for this geometry; verify seating and clamping dimensions before mounting. Where can cutting data for specific materials be obtained? Cutting parameters and recommended feeds and speeds for the P3201-D12 WKP25 can be supplied by Metav Werkzeuge or the Walter Tools technical documentation for the specific material and machine set-up. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Mention of brand names such as Walter Tools serves explanatory purposes only; there is no affiliation between our company and the mentioned manufacturers. The offered item is an original, factory-new product of the manufacturer.
P3201-D12 WKP35 Wendeplatten - Walter Tools Technische Daten: - coating: beschichtetes Hartmetall - material: P / K - Stahl: bearbeitbar - Gusseisen: bearbeitbar - Sorte: WKP35 - Serie: Walter Schneidstoffsorte - Serie offen
Take advantage of the combination of a coated carbide grade (WKP35) and an optimised D12 chipbreaker for consistent chip control and extended tool life; order directly via Metav Werkzeuge or request expert advice from our consultants to ensure the insert matches production needs. P3201-D12 WKP35 indexable milling insert — for steel and cast iron | Walter Tools The P3201-D12 WKP35 is an indexable milling insert engineered for productive face and peripheral milling of steel and cast iron components. Coated carbide grade WKP35 for extended life Optimised D12 chipbreaker for reliable chip control Designed for steel and cast iron machining Walter Tools manufacturing quality and consistency Stable chip control for uninterrupted machining The incorporated D12 chipbreaker delivers predictable chip formation under typical milling conditions, reducing the risk of snarled or tangled chips during continuous operation. With a focus on stable cutting forces, this feature supports steady feed rates and diminishes the need for frequent clearing, which in turn lowers non-productive time. The coated carbide substrate provides a balanced combination of wear resistance and toughness, so the cutting edge maintains its profile over longer runs and helps preserve surface finish consistency on workpieces. Optimised grade for both steel and cast iron Designed around the WKP35 grade, the insert matches the demands of the ISO material groups P (steel) and K (cast iron). The coating and substrate pairing has been selected to cope with the heat and chip forms typical of steels while also resisting the abrasive wear common when machining cast iron. By referencing ISO 513 material groupings, the specification clarifies suitability across a broad materials range and makes selection straightforward for engineering and production teams seeking reproducible results. Production benefits from a compact, serviceable design As a solid choice for milling tool assemblies, the insert reduces tool-change frequency through improved edge life and predictable wear behaviour. The geometry and coating strategy support a balance between cutting efficiency and edge robustness, which can contribute to fewer rejects and more consistent cycle times. The indexable milling insert design allows for quick reversal or replacement without complete tool regrind, helping to keep set-up and maintenance intervals short while maintaining machining accuracy. For reliable machining with the WKP35 grade and guidance on tooling integration, contact Metav Werkzeuge for ordering and technical assistance via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: P3201-D12-WKP35-WALTER Product: Fräswendeschneidplatte (indexable milling insert) ISO designation: P3201-D12 WKP35 Facts Chipbreaker: D12 Grade: WKP35 Material compatibility: P / K (steel / cast iron) Special features Coating: coated carbide Series: Walter Schneidstoffsorte - Serie offen Suitable for: steel and cast iron Manufacturer brand: Walter Tools FAQ What materials is this insert suitable for? The insert is specified for steel and cast iron applications according to ISO groupings P and K; the WKP35 grade supports both material types. How does the D12 chipbreaker improve machining? The D12 chipbreaker promotes short, controllable chips and reduces chip entanglement, which stabilises cutting forces and helps maintain a consistent surface finish. Is the insert coated and what is the benefit? Yes — the WKP35 is a coated carbide grade; the coating enhances wear resistance and extends edge life under typical milling loads. How does WKP35 compare to other grades for mixed production? WKP35 is engineered for broad applicability across steel and cast iron, offering a compromise between toughness and abrasion resistance suited to mixed production runs. Which product designation identifies this item for ordering? The insert is listed as P3201-D12 WKP35 (SKU: P3201-D12-WKP35-WALTER) and is part of the Walter Tools range. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P3201-D12.7 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of a coated carbide grade, a precise chipbreaker D12.7 and Walter Tools’ proven manufacturing to maintain process stability and predictable tool life; order directly via Metav Werkzeuge or consult our technical team for selection advice. P3201-D12.7 WHH15X milling insert by Walter Tools — coated carbide, chipbreaker D12.7 The P3201-D12.7 WHH15X is a milling indexable insert designed for productive milling applications where consistent chip control and wear resistance are required. Coated carbide grade WHH15X Chipbreaker D12.7 for controlled chips Engineered for productive milling Walter grade series – open series Reliable cutting performance through a robust grade The insert is manufactured in a coated carbide grade that aims to deliver stable cutting edge behaviour under a range of conditions. The WHH15X designation identifies a coated hardmetal class designed for general milling tasks; users can expect consistent performance in series production where repeatability matters. Because the material matrix and specific process parameters vary by application, the workpiece suitability should be checked against the product matrix to ensure optimal results. This reduces the risk of unexpected tool wear and supports predictable maintenance cycles. Improved productivity via controlled chip formation A defining element of this design is the chipbreaker D12.7, which promotes consistent chip segmentation and evacuation during milling. Controlled chips reduce rework and downtime, supporting productive machining by keeping cutting forces stable and minimising interruptions for chip clearing. For operations that require uninterrupted runs or where chip handling is critical, this geometry helps maintain cycle times and contributes to surface quality while simplifying post-process handling. Easy specification and reliable integration into toolsets The insert’s conventional designation and series labelling make it straightforward to specify within existing tool assemblies and procurement systems. The catalogue-dependent material note indicates that further product variants or coatings may be available; this allows adaptation to particular machining strategies without changing clamping systems. Integration into standard milling cutter bodies is uncomplicated, enabling quick replacements and predictable process behaviour, which supports continuous production and planning certainty. Contact Metav Werkzeuge for an application consultation or to request the recommended variant of this Walter Tools insert for specific materials and cutting conditions Technical Data Article number: P3201-D12.7-WHH15X-WALTER Designation: P3201-D12.7 WHH15X Type: Milling indexable insert Grade: WHH15X Series: Walter Schneidstoffsorte - Serie offen Facts Chipbreaker: D12.7 SKU: P3201-D12.7-WHH15X-WALTER Special features Coated hardmetal (beschichtetes Hartmetall) Material specification: Catalogue-dependent Product family: Walter Schneidstoffsorte Wendeplatten ISO designation included FAQ What materials is this insert designed for? The P3201-D12.7 WHH15X insert is produced in a coated carbide grade; material suitability depends on the specific product matrix and should be checked for the intended workpiece material. How does the D12.7 chipbreaker affect milling performance? The chipbreaker D12.7 promotes reliable chip segmentation and evacuation, which supports productive machining and reduces interruptions caused by long or tangled chips. Can this insert be used in standard milling cutter bodies? Yes, the insert’s standard designation and geometry allow integration into common cutter systems designed for indexable milling inserts. Where can one get technical advice or order this insert? Technical advice and ordering can be arranged through Metav Werkzeuge; they can advise on the correct variant and any catalogue-dependent options. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and brand names are the property of their respective owners. Brand names and registered trademarks are mentioned for clarification purposes only. There is no affiliation between our company and the named manufacturers. The offered article is an original, factory-new product of the manufacturer.
P3201-D15.87 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of a coated carbide cutting grade (WHH15X), the D15.87 chipbreaker and an open series design to ensure stable chip control and reliable tool life in milling applications. Order the insert directly via Metav Werkzeuge or ask the consultants for tailored advice. P3201-D15.87 WHH15X indexable milling insert – coated carbide grade with chipbreaker D15.87 | Walter Tools The P3201-D15.87 WHH15X is a coated carbide milling insert engineered for general and versatile milling tasks where dependable chip formation and predictable tool life are priorities. Coated carbide grade WHH15X Chipbreaker D15.87 for chip control Open series for broad application Consistent edge life in production Improved chip control for uninterrupted production The insert delivers stable chip formation thanks to the integrated chipbreaker D15.87, which reduces recutting and helps maintain a clean cutting zone. This results in fewer interruptions on the shopfloor and a smoother machining process. For operations where consistent evacuation of chips matters—such as pocketing, face milling or light shoulder milling—the insert contributes to predictable cycle times and reduced secondary operations. The technical design of the chipformer supports reliable performance across variable feeds and depths. Durable coated grade for improved productivity Built on the WHH15X coated carbide grade, the cutting edge provides reliable tool life under general milling conditions. The coating enhances wear resistance and helps to protect the substrate during interrupted cuts. For workshops that process a range of materials, the coating-grade combination provides an economical balance between performance and longevity, reducing the need for frequent tool changeovers and lowering total machining costs per part. Versatile open-series design for application flexibility The open-series configuration of this insert allows compatibility with a wide range of cutter bodies and milling strategies. The design supports adaptable use in different operations, enabling consolidation of tool inventories and simpler tool planning. Because the grade and geometry are optimised for broad application, machining centres benefit from reduced setup complexity and improved uptime—particularly useful in mixed-production environments. Specification guidance and responsible use Material suitability should be checked against the product matrix to ensure optimal results; the grade is catalogue-dependent for specific substrates and coatings. When specifying the insert, consider the cutter body, clamping system and recommended cutting data from the tool holder manufacturer to maximise process reliability. For bespoke applications or unusual workpiece materials, technical consultation is recommended to select the correct grade and geometry for the task. For tailored recommendations on Walter Tools’ WHH15X grade and to arrange supply via Metav Werkzeuge, please contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for application support and ordering guidance. Technical data SKU: P3201-D15.87-WHH15X-WALTER Article: P3201-D15.87 WHH15X Type: Indexable milling insert Brand: Walter Tools Facts Chipbreaker: D15.87 Grade: WHH15X Designation: P3201-D15.87 UID: P3201-D15.87-WHH15X-WALTER Special features Coating: coated carbide Series: Walter cutting-grade series – open Material: catalogue-dependent Application note: verify material suitability against product matrix FAQ What materials is this insert intended for? The P3201-D15.87 WHH15X insert uses a coated carbide grade; suitability for specific materials should be checked against the product matrix provided for the WHH15X grade. How does the D15.87 chipbreaker affect milling performance? The D15.87 chipbreaker improves chip control and evacuation, reducing recutting and contributing to steadier machining conditions and more predictable cycle times. Is the insert compatible with standard cutter bodies? The open-series design permits use with a wide range of cutter bodies; verify seat type and clamping compatibility with the cutter manufacturer before use. What should be considered to maximise tool life? Optimise cutting data for the cutter and workpiece, ensure correct clamping and cooling, and match the WHH15X grade to the workpiece material per the product matrix for best results. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Mention of brand names such as Walter Tools is for explanatory purposes only; there is no affiliation between Metav Werkzeuge and the named brands. The offered item is an original, factory-new product of the manufacturer.
P3201-D16 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide performance and D16 chip control for consistent milling results; order directly via Metav Werkzeuge or consult Metav Werkzeuge for application-specific selection and rapid supply. P3201-D16 WHH15X milling indexable insert, chipbreaker D16 — Walter Tools The P3201-D16 WHH15X is a milling indexable insert designed to deliver dependable chip control and productive cutting performance in a wide range of milling operations. Coated carbide grade WHH15X Chipbreaker D16 for controlled chips Walter open-series cutting grade Optimised for productive milling Stable chip control for uninterrupted machining The insert’s chipbreaker D16 and insert geometry are engineered to produce predictable chip formation, reducing interruptions and improving cycle times. Consistent chip control minimises tool rework and machine downtime, which leads to more stable process flows and higher overall equipment effectiveness. The specification of the chipbreaker clearly indicates its primary role in chip shaping and evacuation during medium to heavy milling operations. Durable coated carbide grade for reliable tool life The WHH15X designation denotes a coated carbide cutting grade developed for balanced wear resistance and toughness. A coated carbide grade provides a hard, wear‑resistant surface layer that reduces flank wear and preserves cutting-edge integrity under thermal and mechanical stress. For practical terms: a coated insert helps maintain cutting performance over longer intervals, reducing tool change frequency and supporting predictable production schedules. Versatile series suited to varied workpiece ranges Listed as part of the Walter cutting‑grade open series, the insert offers flexible application potential; however, workpiece suitability should be verified using the manufacturer’s product matrix. The series concept enables straightforward grade selection for mixed production environments where a single insert is required to handle different materials. This reduces inventory complexity while maintaining process reliability across diverse milling tasks. Selection advice and process efficiency considerations When integrating the insert into a machining process, attention to feed, speed and coolant strategy will realise the grade’s efficiency potential. The combination of coated carbide and the D16 chipbreaker supports elevated metal removal rates when matched to stable clamping and consistent part presentation. For procurement and process planning, specification of the ISO designation and chipbreaker (P3201‑D16 WHH15X / D16) enables precise ordering and reduces the risk of mismatched components. Discuss the WHH15X grade with Metav Werkzeuge to confirm the best insert choice for specific milling applications and to arrange fast delivery — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: P3201-D16-WHH15X-WALTER Designation: P3201-D16 WHH15X Product type: Fräswendeschneidplatte Label: Fräswendeschneidplatte P3201-D16 WHH15X Walter Tools Facts Chipbreaker: D16 Grade: WHH15X (coated carbide) Series: Walter Schneidstoffsorte - Serie offen Material: Katalogabhängig Special features Coated carbide cutting grade Optimised for chip formation (check product matrix) Walter brand Wendeplatte ISO designation: P3201-D16 WHH15X FAQ What materials is the P3201-D16 WHH15X best suited for? The P3201‑D16 WHH15X is a coated carbide milling insert from Walter Tools; material suitability should be checked against the manufacturer's product matrix to confirm compatibility with specific steels or alloys. How does the D16 chipbreaker affect machining performance? The D16 chipbreaker on the P3201‑D16 WHH15X shapes chips for controlled evacuation, reducing the frequency of stoppages and improving process stability for milling operations. Is the WHH15X grade suitable for high-speed milling? WHH15X is a coated carbide grade designed for balanced wear resistance and toughness; its suitability for high‑speed milling depends on the application parameters and should be validated within the process limits provided by Walter Tools. How should the insert be referenced when ordering replacements? Order using the ISO designation and SKU: P3201‑D16 WHH15X (SKU P3201-D16-WHH15X-WALTER) to ensure the correct Walter Tools milling indexable insert is supplied. What performance benefits does the Walter open series offer? The Walter open series, including the WHH15X grade, is intended to provide versatile application potential and simpler grade selection across varied milling tasks, supporting efficiency and inventory rationalisation. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
P3201-D16 WKP25 Wendeplatten - Walter Tools
Benefit from the combination of coated carbide WKP25 and the D16 chipbreaker for controlled chip formation and reliable machining of steel and cast iron; this results in improved process stability and extended tool life. Order the insert directly via Metav Werkzeuge or contact our consultants for application advice. P3201-D16 WKP25 indexable milling insert — D16 chipbreaker, coated carbide by Walter Tools (for steel and cast iron) The P3201-D16 WKP25 is an indexable milling insert designed to provide consistent chip control and wear resistance when machining steel and cast iron in general milling operations Coated carbide grade WKP25 D16 chipbreaker for controlled chip formation Optimised for steel and cast iron machining Walter open-grade series for consistent wear Stable chip control for uninterrupted production The combination of the WKP25 coated carbide grade and the D16 chipbreaker provides a pragmatic solution for common milling challenges when working with steel and cast iron. The grade is engineered to handle the typical heat and abrasion characteristics of these material groups, thereby reducing unpredictable tool wear. The chipbreaker geometry promotes short, manageable chips that lower the risk of recutting and machine downtime, which supports a more steady production rhythm and predictable cycle times. This section emphasises measurable process benefits and supports decision-making on tool selection for industrial milling setups. Longer tool life and consistent surface quality A coated carbide grade such as WKP25 offers improved resistance to abrasive wear and thermal loading compared with uncoated grades; as a result, tool-change intervals are extended and surface finish remains more uniform over the tool life. The insert’s construction is aimed at providing a balance between toughness and hardness appropriate for the P and K ISO material groups. In practical terms, the result is fewer interruptions in the machining sequence and a lower rate of scrap due to inconsistent cutting performance. The technical balance delivered by the grade enhances economic efficiency in medium- to high-volume milling operations. Practical integration and selection guidance The P3201 geometry with D16 chipbreaker is intended for straightforward integration into milling cutters that accept P3201 inserts. When selecting an insert, prioritise the match between insert grade, chipbreaker geometry and the specific cutting parameters of the operation to gain the full benefit of the WKP25 coating. For workshop planners and purchasing managers, the insert is a solid choice where a reliable, everyday milling solution for steel and cast iron is required. Technical advisors can support the correct combination of cutting speed and feed to maximise the insert’s service life and process security. For application-specific advice on Walter Tools WKP25 milling inserts and procurement via Metav Werkzeuge, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and availability Technical data Article number: P3201-D16-WKP25-WALTER SKU: P3201-D16-WKP25-WALTER Designation: P3201-D16 WKP25 Data Grade: coated carbide (WKP25) Chipbreaker: D16 Geometry: P3201 Series: Walter Schneidstoffsorte - Serie offen Special features Material groups: P / K (steel and cast iron) Suitable for machining steel and cast iron (ISO 513) Brand: Walter Tools Product type: indexable milling insert FAQ What materials is this insert designed for? The P3201-D16 WKP25 insert is specified for machining steel and cast iron in accordance with the ISO 513 material group classifications. What does the D16 chipbreaker do? The D16 chipbreaker promotes controlled, short chips during milling operations, improving chip evacuation and reducing the chance of recutting when using the P3201-D16 WKP25 insert. Is WKP25 a coated or uncoated grade? WKP25 is a coated carbide grade developed by Walter Tools to provide a combination of wear resistance and toughness for general steel and cast-iron milling. Which cutter geometry is required for this insert? The insert uses the P3201 geometry; compatibility requires a milling cutter that accepts P3201 indexable inserts. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered article is an original, factory-new product of Walter Tools.
P3201-D16 WKP35 Wendeplatten - Walter Tools
Take advantage of reliable chip control, broad material suitability (steel and cast iron) and consistent edge life to keep machining stable and productive; order or request application advice via Metav Werkzeuge for rapid assistance. Fräswendeschneidplatte P3201-D16 WKP35 – milling indexable insert with D16 chipbreaker by Walter Tools The Fräswendeschneidplatte P3201-D16 WKP35 is a coated carbide insert developed for high process stability in steel and cast iron milling applications Coated carbide grade WKP35 Chipbreaker D16 for stable chip flow Suited to steel and cast iron machining Walter Tools consistency and wear resistance Consistent chip control for predictable productivity The chipbreaker D16 is engineered to shape and direct chips reliably during interrupted and continuous milling. By actively breaking and evacuating swarf, the geometry reduces the risk of chip entanglement and tool-holder clogging, which in turn cuts unplanned stoppages and increases effective machining time. For shops focusing on repeatable cycle times, the controlled chip formation translates into fewer tool changes and steadier surface finishes. The term chipbreaker describes a deliberately formed groove and step on the insert face that alters shear and curl, producing short, manageable chips even under variable cutting conditions. Optimised for steel and cast iron with a coated carbide grade The insert’s WKP35 composition is a coated carbide grade tailored to the thermal and abrasive demands of steel (ISO group P) and cast iron (ISO group K). Coatings improve resistance to flank and crater wear by reducing adhesion and thermal shock during heavy or continuous cuts. For operators, this means more consistent edge life and predictable regrinding intervals. When machining alloyed or unalloyed steels and common cast iron grades, the combination of substrate toughness and coating hardness in this grade balances wear resistance with chipping resistance, delivering a compromise between cutting speed and tool life that suits many general-purpose milling tasks. Predictable cutting-edge performance and integration in systems The open-series design and ISO-style designation (P3201-D16 WKP35) support straightforward selection and replacement in systems compatible with the P3201 family. A stable cutting edge supports surface quality targets and reduces rework, while the geometry’s robustness helps maintain dimensional accuracy over longer tool life. For process engineers, this insert offers a pragmatic balance: good wear behaviour, reliable stable cutting edge performance and compatibility with commonly used toolholders for face and shoulder milling. If uncertainty remains about the most suitable geometry or cutting data for a specific machine or material batch, Metav Werkzeuge provides application advice to align insert choice and machining parameters with production goals. Contact Metav Werkzeuge for tailored application advice and availability of Walter Tools P3201-D16 WKP35; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: P3201-D16-WKP35-WALTER Designation: P3201-D16 WKP35 Product type: Milling indexable insert Brand: Walter Tools Facts Chipbreaker: D16 Coating/substrate: coated carbide grade WKP35 Material suitability: P (steel), K (cast iron) Series: Walter cutting grade series – open series Special features Stable chip control Balanced wear resistance and toughness Suitable for ISO P and ISO K workpieces Designed for use in P3201-compatible holders FAQ What materials is this insert intended for? The P3201-D16 WKP35 insert is intended primarily for machining steel (ISO P) and cast iron (ISO K), offering a balance of wear resistance and toughness for these groups. What is the advantage of the WKP35 grade? WKP35 is a coated carbide grade designed to improve wear resistance and process reliability when machining steel and cast iron, resulting in more predictable edge life and fewer unscheduled tool changes. How does the D16 chipbreaker improve milling? The chipbreaker D16 shapes chips to be short and controllable, which reduces the chance of chip accumulation, lowers machine downtime and helps maintain consistent surface quality. Will the insert fit standard holders for this geometry? The ISO-style designation P3201-D16 indicates compatibility with toolholders made for the P3201 family; ensure the holder accepts the P3201 form to guarantee correct seat and clamping. How does Walter Tools ensure consistent performance? Walter Tools combines dedicated substrate composition and coating technology with tested geometries to provide stable cutting-edge behaviour and reproducible results across production batches. Manufacturer / Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered article is original, brand-new merchandise from the manufacturer.
P3201-D19.05 WHH15X Wendeplatten - Walter Tools
Take advantage of a combination of stable chip control and a coated carbide grade for consistent, productive milling. The controlled D19.05 chipbreaker and the WHH15X grade deliver wear-resistant performance in indexable milling operations — order or request application advice from Metav Werkzeuge. P3201-D19.05 WHH15X indexable milling insert with D19.05 chipbreaker — Walter Tools A P3201-D19.05 WHH15X indexable milling insert engineered for reliable chip control and versatile milling applications in industrial cutting environments Coated carbide grade WHH15X Chipbreaker D19.05 for controlled chips Open series for broad application range Designed for indexable milling systems Controlled chip formation for safer, faster cutting The integration of a defined D19.05 chipbreaker provides predictable chip control, helping to avoid long, stringy chips and reducing interruptions. As an indexable insert, this geometry optimises chip curl and evacuation, which in turn supports steady metal removal rates and a more consistent surface finish. The result is a measurable reduction in process variability and fewer unplanned stoppages during batch production. Durable cutting edge from a coated carbide grade The WHH15X designation indicates a coated carbide composition developed for wear resistance and edge stability under a variety of conditions. The coating enhances flank and crater wear performance, enabling longer intervals between index changes and supporting higher productivity. Material suitability should be confirmed with the supplier matrix, since the grade is intended to balance tool life with broad applicability rather than be a single‑material solution. Practical integration and process benefits As a P3201 series insert, the geometry aligns with common indexable milling systems to permit quick insert indexing and replacement, reducing machine downtime. The combination of geometry and grade aims to improve overall productivity and extend tool life, while the open series designation offers flexibility across different cutting strategies. For specific holder compatibility and cutting parameter recommendations, consult the product matrix or Metav Werkzeuge for tailored guidance. Contact Metav Werkzeuge for precise application recommendations and to source Walter Tools WHH15X inserts for improved milling stability Technical Data Article number: P3201-D19.05-WHH15X-WALTER SKU: P3201-D19.05-WHH15X-WALTER Product type: Indexable milling insert Facts Designation: P3201-D19.05 Chipbreaker: D19.05 Grade: WHH15X Special features Coating: coated carbide (beschichtetes Hartmetall) Series: Walter Schneidstoffsorte - Serie offen Material information: Katalogabhängig FAQ What is the primary function of the D19.05 chipbreaker? The D19.05 chipbreaker on the P3201-D19.05 WHH15X insert shapes and controls chip formation to promote consistent evacuation and reduce the risk of stringing during milling. Which materials is the WHH15X grade intended for? The WHH15X grade is a coated carbide designed for broad applicability; specific material suitability should be verified in the product matrix for the P3201-D19.05 WHH15X by Walter Tools. How does the coating on WHH15X benefit machining? The coating improves wear resistance and protects the cutting edge, which can extend insert life and support higher productivity compared with uncoated grades. Can this insert be used in standard indexable milling systems? The P3201-D19.05 WHH15X is designed for integration into indexable milling systems; holder compatibility should be checked against the toolholder specifications and the product matrix. Where to find cutting parameters for the P3201-D19.05 WHH15X? Cutting parameters and application recommendations are available in the technical documentation or from Metav Werkzeuge, which can provide specific guidance for the P3201-D19.05 WHH15X insert. The Walter AG (brand presentation: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Trademarked names and product designations are the property of their respective owners. Brand names and protected designations are mentioned for explanation only. There is no affiliation between Metav Werkzeuge and the mentioned manufacturers. The offered item is original and brand-new from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
P3201-D20 WHH15X Wendeplatten - Walter Tools
Take advantage of the proven combination of D20 chip control, a WHH15X coated carbide grade and the compact ISO designation for stable, productive milling cycles; order genuine inserts through Metav Werkzeuge or consult the specialists for application matching and in-house process optimisation. P3201-D20 WHH15X – P3201-D20 WHH15X milling indexable insert (D20 chipbreaker) – Walter Tools A P3201-D20 WHH15X milling indexable insert designed for versatile face and slot milling, featuring a D20 chipbreaker and a coated carbide grade optimised for controlled chip formation and consistent cutting performance D20 chipbreaker for controlled chips Coated carbide WHH15X for wear resistance Designed for versatile milling tasks Better chip control and steady machining performance The central benefit of the design is consistent chip control through the D20 chipbreaker, which reduces material buildup and improves evacuation in interrupted or continuous cuts. This results in fewer process interruptions and more predictable cycle times, helping to increase overall productivity on the shop floor. For machinists working across varied components, the controlled chip geometry supports stable cutting forces and reduces the need for frequent manual clearing, which in turn lowers non-productive time and contributes to a smoother production flow. Extended tool life through modern coated carbide technology Built on the WHH15X coated carbide concept, the insert offers a balanced combination of wear resistance and edge stability. The coating technology reduces flank and crater wear under typical milling conditions, leading to longer edge life and fewer indexings. Longer tool life translates into lower tooling costs per part and reduced machine downtime for insert changes, which is especially relevant for medium-volume production runs and mixed-material batches where repeatability and cost-efficiency are essential. Process reliability and application flexibility The open series designation from the manufacturer indicates a broad applicability range; however, final suitability should be determined using the specific product matrix. The insert’s geometry promotes process reliability in both face milling and slotting operations, and the standardised ISO designation simplifies tool planning and holder selection. Using standardised insert types reduces inventory complexity and makes it easier to specify replacements without ambiguity when preparing tool lists for job planning or CAM setups. Practical guidance for selection and integration When integrating these inserts into a tool system, consider matching the insert grade and chipbreaker with the intended material and cutting parameters. The P3201-D20 WHH15X is presented for adaptable use—consult the technical matrix for best-cutting speeds, feeds and depth of cut to match the workpiece material. Trial runs under controlled conditions are recommended to establish the optimal feed per tooth and cutting speed; such trials typically show improved surface finish and consistent tool wear patterns when the appropriate WHH15X parameters are applied. For genuine Walter Tools P3201-D20 WHH15X inserts and expert advice on process integration, contact Metav Werkzeuge for application support and availability: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data SKU: P3201-D20-WHH15X-WALTER Designation: P3201-D20 WHH15X Product type: Milling indexable insert Manufacturer: Walter Tools Core data Chipbreaker: D20 Material grade: WHH15X (coated carbide) Series: Walter Schneidstoffsorte - Serie offen Special features Material information: Katalogabhängig Coating: Coated carbide Range designation: P3201-D20 WHH15X UID: P3201-D20-WHH15X-WALTER FAQ What milling tasks is this insert best suited to? The insert is optimised for face and slot milling; the D20 chipbreaker and WHH15X coating make the insert suitable for a range of general milling applications where controlled chip formation and wear resistance are required. How does the D20 chipbreaker affect machining? The D20 chipbreaker promotes controlled chip segmentation and evacuation, which improves process stability and reduces the chance of chip entanglement during interrupted cuts or narrow-slot operations with the P3201-D20 WHH15X insert. Is the WHH15X grade suitable for hardened materials? WHH15X is a coated carbide grade; material suitability must be verified against the product matrix for the P3201-D20 WHH15X to confirm compatibility with specific hardness ranges or alloys. Can existing toolholders be used with this insert? The ISO designation simplifies holder selection; the P3201-D20 WHH15X insert fits into compatible indexable milling cutters designed for the same ISO geometry—verify seat and clamping compatibility before fitting. What benefits are expected from using Walter Tools inserts? Walter Tools inserts like the P3201-D20 WHH15X are designed for improved process reliability, consistent cutting edges and predictable wear behaviour, which supports higher productivity and repeatable results. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and product names remain the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no affiliation or partnership between Metav Werkzeuge and the mentioned brands; the offered item is an original, factory-new product from the manufacturer Walter Tools.
P3201-D20 WKP25 Wendeplatten - Walter Tools Technische Daten - coating: beschichtetes Hartmetall - material: P / K - stahl_material_anwendung: geeignet für Stahl - cast_iron_material_anwendung: geeignet für Gusseisen
Take advantage of the combination of reliable chip control, a coated carbide grade tuned for steel and cast iron, and Walter Tools' consistent edge performance to keep milling processes productive and repeatable. Order genuine inserts directly via Metav Werkzeuge or consult the specialists for cutting data and application support. P3201-D20 WKP25 indexable milling insert – D20 chipbreaker for steel and cast iron, Walter Tools The P3201-D20 WKP25 is an indexable milling insert designed for high‑productivity finishing and roughing in steel and cast iron applications. Coated carbide grade WKP25 D20 chipbreaker for reliable chip control Optimised for steel and cast iron machining Walter Tools consistency and edge life Enhanced chip control for consistent productivity The D20 chipbreaker geometry provides predictable chip control, reducing interruptions and enabling higher metal removal rates. By guiding chips away from the cutting zone, the insert lowers the risk of re-cutting and workpiece damage, which directly improves productivity and reduces downtime. The geometry is engineered to handle the typical chip forms encountered in P and K materials, promoting stable cutting forces and an extended edge life compared with non‑optimised geometries. Optimised compatibility with steel (P) and cast iron (K) Designed for the ISO material groups P (steel) and K (cast iron), this insert balances toughness and wear resistance to suit both continuous and interrupted cuts. For steel, the grade manages the heat and continuous chips; for cast iron, the plate copes with abrasive wear and short, brittle chips. The WKP25 grade is a coated carbide formulation that supports repeatable surface quality and consistent tool performance across a wide range of batch and single‑piece productions, making it suitable for mixed‑material shops and production lines. Coated carbide grade for reliable process security The coated carbide composition of the WKP25 grade offers a protective layer that improves resistance to abrasive wear and thermal loads. Coatings reduce adhesion and flank wear, so cutting data can be pushed safely while maintaining dimensional accuracy. Combined with the insert’s defined geometry and the P3201‑D20 form, operators gain a machining solution that contributes to predictable tool life, fewer tool changes and lower overall machining costs. The result is a dependable insert that supports consistent component quality and operational efficiency. For application advice, availability of Walter Tools WKP25 inserts or tailored cutting recommendations, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss supply and cutting data. Technical Data SKU: P3201-D20-WKP25-WALTER Article: P3201-D20 WKP25 Type: Indexable milling insert Brand: Walter Tools Grade: WKP25 Chipbreaker: D20 Facts ISO designation: P3201-D20 WKP25 Material groups: P / K Geometry designation: P3201-D20 Special features Coated carbide (WKP25) Suitable for steel (P) and cast iron (K) D20 chipbreaker for controlled chip formation Series: Walter grade series – open series FAQ What materials is this insert intended for? The P3201-D20 WKP25 insert is intended for ISO groups P and K, meaning it is suited for steel and cast iron machining where the WKP25 coated carbide balance of toughness and wear resistance is required. How does the D20 chipbreaker affect machining performance? The D20 chipbreaker on this indexable milling insert controls chip formation and evacuation, improving process stability and reducing the likelihood of built‑up edge or workpiece surface damage. Can this insert be used for both finishing and roughing? Yes, the combination of the WKP25 coated carbide grade and the D20 chipbreaker makes the insert versatile for light finishing cuts and heavier roughing operations, depending on the chosen cutting data. How does the WKP25 grade compare in terms of wear resistance? WKP25 is a coated carbide grade formulated to offer enhanced wear resistance and thermal stability, which supports longer tool life and consistent results across typical steel and cast iron applications. What information is needed to select the correct insert geometry and cutting data? Provide the workpiece material (P or K), machining operation (roughing or finishing), machine power and spindle speed ranges; with these details, the P3201-D20 WKP25 insert selection and cutting data can be optimised for the application. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade marks are mentioned for explanatory purposes only; there is no connection between our company and the named brands. The offered item is original factory‑new goods of Walter Tools.
P3201-D20 WKP35 Wendeplatten - Walter Tools
Take advantage of the combination of WKP35 coated carbide and a D20 chipbreaker for reliable, productive machining of steel and cast iron; the insert delivers consistent cutting performance and stable chip control, supporting continuous production. Order directly via Metav Werkzeuge or consult the technical advisors for geometry-specific recommendations. P3201-D20 WKP35 (P3201-D20) milling insert — WKP35 coated carbide, D20 chipbreaker | Walter Tools P3201-D20 WKP35 — an indexable milling insert designed for productive machining of steel and cast iron in a wide range of industrial milling applications Coated carbide grade WKP35 D20 chipbreaker for stable chip control Designed for steel and cast iron machining Walter Tools open series, productive cutting Delivering consistent results for steel and cast iron machining The hardened, coated carbide WKP35 grade is engineered for the thermal and mechanical demands of turning and milling steel and cast iron, which means predictable wear behaviour and repeatable results under standard industrial conditions. The substrate and coating combination lowers flank wear and helps maintain dimensional accuracy over longer tool life, translating into fewer tool changes and more uptime. The design supports catalogue-dependent geometries, so selection of the correct insert geometry will directly influence surface finish and cycle times Better chip control to reduce stoppages and improve productivity The D20 chipbreaker geometry improves fragmentation and evacuation of chips during milling operations. By breaking and directing chips away from the cutting zone, the insert reduces the risk of re-cutting, built-up edge and thermal peaks. For practical terms: stable chip behaviour results in fewer interruptions for manual clearing, more consistent tool contacts and improved process stability — particularly beneficial when machining interrupted cuts or harder-to-manage cast-iron grades. The chip management feature is especially useful in automated or multi-pass operations Stable cutting edge for reliable, cost-effective performance A stable cutting edge is central to predictable process costs. The WKP35 coating provides enhanced resistance to abrasive wear while retaining a robust edge for tough industrial cycles. This balance of hardness and toughness supports repetitive production runs with less variation in insert life, improving the cost-per-component ratio. In operations that prioritise surface quality and repeatability, the observed effect is fewer reworks and lower scrap rates, which contributes directly to overall manufacturing efficiency Practical integration and recommendations for application Integrating this insert into existing toolholders is straightforward when geometry and clamping systems match the specified catalogue design. The grade is intended for standard industrial milling setups where steel and cast iron are predominant materials; cutting data and optimal feed parameters remain geometry- and machine-dependent. For customers seeking process assurance, detailed advice on ideal cutting conditions, compatible cutter bodies and expected tool life is available from Metav Werkzeuge, enabling a tailored selection that aligns insert geometry with production goals For application-specific recommendations or to secure availability of the Walter Tools WKP35 grade, contact Metav Werkzeuge for technical support and procurement at info@metav-werkzeuge.com or by phone +49 2822 7131930 Technical Data Article number: P3201-D20-WKP35-WALTER Name: P3201-D20 WKP35 Manufacturer: Walter Tools Product type: Milling insert Facts Grade: WKP35 Chipbreaker: D20 Material groups: P (steel), K (cast iron) Series: Walter Schneidstoffsorte - Serie offen Special features Coated cemented carbide Optimised for stable chip control Suited to industrial milling applications Catalogue- and geometry-dependent main application FAQ Which materials is this insert suitable for? The P3201-D20 WKP35 insert is designed primarily for steel (P) and cast iron (K) machining in accordance with ISO groupings, offering suitable wear resistance for typical industrial applications. What is the advantage of the D20 chipbreaker? The D20 chipbreaker enhances chip fragmentation and evacuation, improving process stability and reducing the risk of re-cutting and built-up edge during milling operations. Is WKP35 a coated grade and what does that mean? Yes — WKP35 is a coated carbide grade; the coating improves abrasive wear resistance while the carbide substrate maintains toughness, which together extend edge life in demanding cycles. Can this insert be used for interrupted cuts? The combination of a robust grade and the D20 chip geometry makes the insert suitable for many interrupted cutting scenarios, with improved chip control and reduced edge degradation. Where can additional cutting data and compatible geometries be obtained? Detailed cutting parameters and geometry compatibility are catalogue-specific; Metav Werkzeuge can provide tailored recommendations based on the intended cutter body and machining conditions. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Walter AG (brand appearance: Walter Tools), headquartered in Tübingen, is among the world's leading manufacturers of precision tools for metalworking and forms part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are used for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
P3201-D25 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of a coated carbide grade, an engineered chipbreaker D25 and Walter's open-series design for steady tool life and reliable chip control; order the insert via Metav Werkzeuge or ask their consultants for application-specific guidance. P3201-D25 WHH15X indexable milling insert by Walter Tools — coated carbide grade with D25 chipbreaker The P3201-D25 WHH15X is a versatile indexable milling insert intended for general milling tasks where consistent chip formation and predictable cutting behaviour are required Coated carbide grade WHH15X Chipbreaker D25 for controlled chip flow Walter open series for broad application Check product matrix for material suitability Predictable chip control for stable production The combination of the chipbreaker D25 and a coated carbide grade delivers controlled chip formation that supports continuous production. Controlled chips reduce the risk of re-cutting and tool interference, which in turn helps to maintain a steady surface finish and lowers the likelihood of unexpected stoppages. For process planners this means fewer interventions during a machining cycle and improved overall productivity when using this indexable milling component. Broad application potential with clear material guidance The WHH15X designation identifies a Walter cutting grade within the open series and indicates a coated carbide substrate intended for a wide material spectrum. Material compatibility should be verified in the manufacturer’s product matrix before final selection; the matrix provides the decisive match between workpiece materials and the cutting grade. Selecting the appropriate grade on that basis can reduce the number of tool changes and simplify inventory management for mixed-production environments. Improved repeatability and maintenance advantages A stable cutting geometry helps to preserve a consistent cutting edge over multiple indexings, which benefits repeatability and measurement-controlled processes. The open-series design supports flexible use across various setups, while the coating extends abrasive resistance and promotes longer tool life under recommended conditions. For maintenance planning, predictable wear behaviour simplifies spare-part strategies and contributes to smoother shift-to-shift handovers. Application support and planning recommendations Because the grade belongs to an open Walter series, process engineers are advised to consult the product matrix and consider machining parameters in context — cutting speeds, feed per tooth and depth of cut determine whether the grade is the best fit for a given component. When parameters are uncertain, Metav Werkzeuge’s consultants can assist with parameter selection and help interpret the product matrix to match the insert to the required material and cutting conditions. Contact Metav Werkzeuge for tailored application advice and availability: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: P3201-D25-WHH15X-WALTER Item designation: P3201-D25 WHH15X Product type: Fräswendeschneidplatte (indexable milling insert) Manufacturer: Walter Tools Grade: WHH15X Series: Walter Schneidstoffsorte - Serie offen Chipbreaker: D25 Material specification: Katalogabhängig (coated carbide per product matrix) Facts SKU: P3201-D25-WHH15X-WALTER Special features Coating: coated carbide (sortenbeschreibung indicates coated hard metal) Application note: verify workpiece suitability in the product matrix Intended use: milling / indexable insert applications FAQ What workpiece materials suit this insert best? Suitability depends on the product matrix; the P3201-D25 WHH15X is a coated carbide grade intended for a broad material range, but the exact match should be checked in the manufacturer’s matrix. How does the D25 chipbreaker influence machining behaviour? The chipbreaker D25 promotes controlled chip flow and reduces the chance of re-cutting, contributing to more stable machining and a consistent surface finish with the Walter indexable milling insert. Is the WHH15X grade suitable for high-speed machining? High-speed suitability is not specified here; consult the product matrix and machining recommendations or contact Metav Werkzeuge for guidance on whether the WHH15X grade fits a high-speed application. How often should the insert be indexed or replaced? Indexing and replacement intervals depend on cutting conditions and workpiece material; the coated carbide substrate and Walter open-series design aim to offer predictable wear, but specific intervals should be determined from test cuts and process monitoring. Where to get help selecting the right grade and parameters? Metav Werkzeuge’s consultants can assist with grade selection and parameter settings; they can interpret the Walter product matrix and advise on feeds, speeds and expected tool life for the targeted application. Manufacturer: Walter AG (brand: Walter Tools); Walter AG (marketed as Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision cutting tools and forms part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners and are cited here for explanatory purposes only. There is no affiliation between our company and the referenced brands; the offered article is original and factory-new from the manufacturer.
P3201-D25 WKP25 Wendeplatten - Walter Tools
Take advantage of the WKP25 grade’s combination of coated carbide toughness and the D25 chipbreaker for reliable chip control and sustained productivity on steel and cast iron; order directly via Metav Werkzeuge or request advice from the consultants at Metav Werkzeuge for machining process support. Fräswendeschneidplatte P3201-D25 WKP25 — milling indexable insert with D25 chipbreaker by Walter Tools The Fräswendeschneidplatte P3201-D25 WKP25 is a coated carbide milling insert engineered for productive machining of steel and cast iron, designed to deliver stable chip formation and consistent tool life in series production. Coated carbide WKP25 grade D25 chipbreaker for predictable chips High productivity on steel and cast iron Walter open-series cutting grade Improved productivity through material-tailored grade The WKP25 cutting grade is a coated carbide formulation optimised for the thermal and mechanical conditions encountered when machining steel (ISO group P) and cast iron (ISO group K). Its composition and coating promote stable wear behaviour, which extends the effective tool life and reduces the frequency of indexable insert changes. For production environments where cycle time and repeatability matter, the result is fewer interruptions and a more predictable process window. The technical design supports common milling strategies and is compatible with standard toolholders used in face and peripheral milling, enabling integration into existing tooling systems without major adaptation. Consistent chip control and surface quality with D25 geometry The D25 chipbreaker geometry concentrates on efficient chip segmentation and evacuation, which limits entanglement and supports uninterrupted machining at elevated feed rates. By promoting short, controlled chips, the insert reduces the risk of workpiece damage and toolholder clogging, improving surface finish and reducing rework. The geometry also assists in heat distribution at the cutting edge, which contributes to more uniform flank wear and stable dimensional output over longer tool campaigns. These benefits translate into measurable improvements in first-pass yield and lower downstream inspection workload. Practical benefits for shop-floor reliability and tool management Incorporating this indexable insert into a machining routine improves logistical handling and cost allocation. The open-series designation from Walter Tools facilitates straightforward grade selection across similar geometries; sort allocation becomes simpler and downtime for grade trials is reduced. For process engineers, the coated grade and chipbreaker combination mean better tolerance control across varied workpiece batches, supporting higher throughput with consistent part quality. When documentation or cutting data is required, Metav Werkzeuge can supply catalogue references and application notes to align the insert selection with machining parameters and material batch characteristics. For machining projects that demand consistent performance from a trusted brand, contact Metav Werkzeuge to align the Walter Tools P3201-D25 WKP25 insert with the production requirements or to arrange immediate supply through Metav Werkzeuge. Technical Data SKU: P3201-D25-WKP25-WALTER Article: Fräswendeschneidplatte P3201-D25 WKP25 Manufacturer: Walter Tools Product type: Fräswendeschneidplatte Facts Grade: WKP25 Chipbreaker: D25 Material code: P / K Series: Walter Schneidstoffsorte - Serie offen Special features Coated carbide cutting grade (beschichtetes Hartmetall) Suitable for Steel (P) and Cast iron (K) Stable chip control with D25 chipbreaker Designed for series production and repeatability FAQ What materials is this insert suitable for? The Fräswendeschneidplatte P3201-D25 WKP25 is specified for steel (ISO group P) and cast iron (ISO group K), reflecting its WKP25 coated carbide formulation. How does the D25 chipbreaker affect machining? The D25 chipbreaker promotes short, controlled chips and reliable evacuation, which improves surface finish and reduces the risk of toolholder clogging when using the P3201-D25 WKP25 insert. Is this insert appropriate for high-volume production? Yes, the WKP25 grade and stable wear behaviour of the Fräswendeschneidplatte P3201-D25 WKP25 make it well suited to continuous series production where process stability and repeatable tool life are priorities. Can the grade be used for both roughing and finishing operations? The WKP25 cutting grade is optimised for a range of cutting conditions on steel and cast iron; specific suitability for roughing or finishing will depend on tool geometry and cutting parameters, which can be coordinated via Metav Werkzeuge. What is the series designation and what does it mean for procurement? This insert belongs to the Walter Schneidstoffsorte - Serie offen, which simplifies grade selection across compatible geometries and assists in stock management. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and product names are the property of their respective owners. Brand names and protected designations are cited exclusively for explanatory purposes. There is no commercial association between Metav Werkzeuge and the mentioned manufacturers; the offered item is an original, factory-new product of the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com