P3201-D25 WKP35 Wendeplatten - Walter Tools
Take advantage of the combination of WKP35 coated carbide, precise D25 chip control and versatile suitability for Stahl and cast iron to raise machining productivity and reduce tool changes. Order or request further cutting data via Metav Werkzeuge for efficient integration into production. Fräswendeschneidplatte P3201-D25 WKP35 — milling insert for Stahl and cast iron, Walter Tools A Fräswendeschneidplatte P3201-D25 WKP35 engineered for productive milling operations, offering a coated carbide grade tailored to the machining of Stahl and cast iron in general-purpose milling applications. Coated carbide grade WKP35 D25 chipbreaker for controlled chip formation Suited for Stahl and cast iron machining Open series for broad application range High reliability for continuous production The WKP35 grade is a coated carbide indexable solution that addresses the typical thermal and wear demands of machining Stahl and cast iron. Designed as part of an open series, the insert combines wear resistance with consistent cutting-edge stability to help maintain component tolerances over longer tool life. Coatings reduce adhesion and flank wear, which translates into fewer tool changes and more predictable maintenance intervals — a key factor for reliable throughput on serial milling tasks. Precise chip control and surface quality Equipped with the D25 chipbreaker, this insert promotes controlled chip formation across a variety of engagement conditions. For cast iron, the breaker encourages short, easily evacuable chips, while for many Stahl applications it aids in splitting or curling chips to avoid entanglement. The result is reduced downtime from chip-related stoppages and a more consistent surface finish, which supports downstream processes and reduces rework. Versatility that supports machining strategies As part of the Walter Schneidstoffsorte open series, the insert is suited to catalogue- and geometry-dependent tasks across P and K material groups. The coated carbide construction helps the tool withstand abrasive or adhesive wear mechanisms typical of these materials, enabling higher cutting speeds and steady productivity gains. The design supports a measured balance between edge robustness and the ability to generate the intended chip form, which helps with process planning and cycle-time optimisation. Practical integration and technical support The insert is specified for common milling operations where robust, repeatable performance is required. Detailed cutting data, recommended speeds and feeds, and compatible toolholder geometries can be provided to aid selection and parameter setting. For production teams seeking to improve milling throughput without sacrificing component quality, the combination of D25 chip control and the WKP35 grade represents a pragmatic choice for many machining scenarios. Discuss application-specific insert selection with Metav Werkzeuge and request the cutting data sheet for Walter Tools WKP35 inserts via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: P3201-D25-WKP35-WALTER Designation: P3201-D25 WKP35 Product type: Fräswendeschneidplatte Manufacturer: Walter Tools Facts Chipbreaker: D25 Material group: P / K Series: Walter Schneidstoffsorte - Serie offen Material: coated carbide Special features Schneidstoffsorte: WKP35 Coated carbide for improved wear resistance Suited for machining of Stahl and cast iron Optimised for typical heat and chip formation in Stahl FAQ What materials is this insert suitable for? The Fräswendeschneidplatte P3201-D25 WKP35 is specified for the ISO P and K groups and is suitable for machining Stahl and cast iron. What does the WKP35 designation indicate? WKP35 denotes the Walter Tools coated carbide grade designed for balanced performance between wear resistance and edge stability in general milling applications. How does the D25 chipbreaker affect machining? The D25 chipbreaker on this indexable insert controls chip shape and evacuation, supporting safer, more consistent milling of cast iron and many Stahl grades. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and product names are the property of their respective owners. Mentions of brand names in this description are for explanatory purposes only and do not indicate any affiliation between our company and the trademark owners. The item offered is an original, factory-new product of the manufacturer.
P3201-D25.4 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of a coated‑carbide WHH15X grade, a D25.4 chipbreaker and Walter Tools know‑how to secure stable chip formation and consistent cutting performance; order or request advice via Metav Werkzeuge for application support and availability. P3201-D25.4 WHH15X — Milling indexable insert with D25.4 chipbreaker (Walter Tools) A P3201‑D25.4 WHH15X indexable milling insert engineered for versatile milling tasks where controlled chip formation and reliable edge life are required Coated carbide grade WHH15X Chipbreaker D25.4 for controlled chip flow Open series for broad material coverage Stable cutting edge for productive machining Predictable performance through material and geometry The indexable milling insert combines a coated carbide substrate with the WHH15X grade to provide consistent performance across a wide range of machining tasks. The coating increases wear resistance while the substrate maintains toughness; together they reduce flank wear and edge chipping. For industrial buyers this translates into fewer insert changes and more stable cycle times. The insert’s geometry, identified by the D25.4 chipbreaker, is optimised for reliable chip control during interrupted or continuous milling, which supports stable spindle loads and predictable tool life. Coating and edge integrity that extend productive windows A coated grade such as WHH15X offers improved surface interaction at the cutting edge, resulting in reduced chemical wear and heat‑related degradation. This leads to extended service intervals and improved surface quality on the workpiece. The term coated carbide refers to a hardmetal body with a fine coating layer that protects the cutting edge; for purchasers not specialised in coatings, this means longer useful life and consistent dimensional results. Toolroom planners can therefore benefit from higher uptime and a lower total cost per component when using this type of insert. Application guidance and process benefits The D25.4 chipbreaker is designed to produce controllable chips that evacuate reliably under typical milling conditions, supporting chip management in both automated and manual setups. The insert is supplied in an open series that indicates broad potential applicability; however, suitability for specific workpiece materials should be verified against the product matrix supplied by the manufacturer. In practice, the combination of a stable cutting edge and effective chip control improves process reliability and helps achieve the targeted surface finish with fewer rework cycles. Contact Metav Werkzeuge for availability, batch options and tailored application advice on Walter Tools P3201‑D25.4 WHH15X milling indexable inserts Technical Data Article number: P3201-D25.4-WHH15X-WALTER Label: Fräswendeschneidplatte P3201-D25.4 WHH15X Walter Tools Product type: Fräswendeschneidplatte / milling indexable insert ISO designation: P3201-D25.4 WHH15X Grade: WHH15X Chipbreaker: D25.4 Series: Walter Schneidstoffsorte - Serie offen Material (catalogue dependent): Katalogabhängig Manufacturer: Walter Tools Core specifications Chipbreaker dimension/designation: D25.4 SKU: P3201-D25.4-WHH15X-WALTER Special features Coating: coated carbide (described as a coated hardmetal grade) Series description: Walter Schneidstoffsorte - Serie offen Application note: Verify suitability for workpiece materials using the product matrix Function: Indexable milling insert for controlled chip formation and stable edge life FAQ What materials is this insert intended to machine? The WHH15X is a coated carbide grade intended for a broad material range; suitability for specific alloys should be checked in the product matrix for the P3201‑D25.4 WHH15X insert. How does the D25.4 chipbreaker affect machining? The D25.4 chipbreaker produces controlled chips that evacuate cleanly, reducing the risk of entanglement and helping to maintain steady cutting forces during milling operations. Is the insert suitable for finishing operations? The coated grade and stable cutting edge of this insert support high‑quality surface finishes; selection between roughing and finishing will depend on the chosen insert geometry and cutting parameters. What does 'open series' mean for application planning? 'Open series' indicates broader applicability across different workpiece materials; nevertheless, the P3201‑D25.4 WHH15X should be matched to the intended material and process via the manufacturer's matrix for best results. Manufacturer: Walter Tools; Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden; support.coromant@sandvik.com The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is among the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade marks are mentioned exclusively for explanation purposes. There is no connection between our company and the mentioned brands. The offered item is an original, factory‑new product of the manufacturer.
P3201-D30 WHH15X Wendeplatten - Walter Tools
Take advantage of the WHH15X coated-carbide grade and the D30 chipbreaker to improve cycle stability and reproducible chip control; order the P3201-D30 WHH15X directly via Metav Werkzeuge or consult the technical team for application matching. P3201-D30 WHH15X — Milling insert, coated carbide, D30 chipbreaker (Walter Tools) The P3201-D30 WHH15X is a coated-carbide milling insert with a D30 chipbreaker, intended for general milling operations where consistent chip formation and reproducible tool life are required; suitability for specific materials should be verified in the product matrix. Milling insert »P3201-D30 WHH15X« by Walter Tools Coated carbide grade WHH15X D30 chipbreaker for controlled chip formation Open-series Walter grade — check product matrix Consistent performance from a proven cutting grade The WHH15X grade is described as a coated carbide cutting material designed to offer balanced wear resistance and toughness. In practise, this means the insert supports steady cutting forces across typical milling operations, which contributes to predictable tool life and fewer unexpected interruptions in production. The coating reduces flank wear and helps maintain dimensional stability of the workpiece over longer tool runs. For milling shops seeking repeatable results, the combination of a robust substrate and a protective coating delivers measurable benefits in process reliability and machining throughput. Stable chip control for safer, cleaner milling The D30 chipbreaker is engineered to influence chip shape and evacuation; its geometry promotes segmented chips in many common milling conditions, reducing the risk of long, entangling swarf and easing automatic chip removal. Improved chip control reduces rework and secondary handling, and can lower cycle times in automated cells. When paired with the WHH15X grade, the insert offers a synergy between edge stability and chip formation behaviour. Note that chipforming behaviour depends on cutting parameters and the specific workpiece material — consult the product matrix to select parameters that match the application. Integration and application guidance for production use This milling insert is supplied in Walter’s open series and is catalogued for flexible allocation; material suitability must be checked against the product matrix before specification. The insert is intended for integration into standard milling cutter systems that accept the P3201-D30 geometry; compatible clamping and correct seat preparation are decisive for achieving the stated performance. For practical adoption, consider trial runs at controlled feeds and depths to determine the optimal cutting window. If further technical data are required, Metav Werkzeuge provides application advice and can supply the necessary documentation for process planning. Contact Metav Werkzeuge for tailored application advice or to request detailed specifications and availability for the P3201-D30 WHH15X — info@metav-werkzeuge.com • +49 2822 7131930 Technical Data Article number: P3201-D30-WHH15X-WALTER SKU: P3201-D30-WHH15X-WALTER Product: Milling insert (Fräswendeschneidplatte) Manufacturer: Walter Tools Grade: WHH15X Chipbreaker: D30 ISO designation: P3201-D30 WHH15X UID: P3201-D30-WHH15X-WALTER Material information: Katalogabhängig Facts No further numerical specifications provided in the data Special features Coated carbide cutting grade (WHH15X) Open-series Walter Schneidstoffsorte Chipbreaker designation D30 Sorteneinsatz: check specific product matrix for material suitability FAQ What materials is this insert suitable for? Material suitability must be verified in the product matrix; the P3201-D30 WHH15X uses a coated carbide grade intended for a broad range of milling tasks but specific recommendations depend on the workpiece material. How does the D30 chipbreaker affect machining? The D30 chipbreaker shapes swarf to improve evacuation and reduce entanglement, aiding automated extraction and safer manual handling during milling operations. Can the insert be used in standard milling cutters? Yes, the geometry corresponds to a standard P3201-D30 seat; correct clamping and seat condition are essential for achieving the expected performance with this Walter Tools milling insert. Is technical support available for process optimisation? Metav Werkzeuge and Walter Tools can provide application guidance and parameter recommendations to help optimise cutting data and extend tool life for the P3201-D30 WHH15X. Manufacturer: Walter AG; Tübingen, Germany Protected trademarks and trade names belong to their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between our company and the named brands; the offered item is an original, factory-new product of the manufacturer.
P3201-D31.75 WHH15X Wendeplatten - Walter Tools
Benefit from the WHH15X coated carbide grade combined with the D31.75 chipbreaker for consistent chip formation and reliable milling results; the insert delivers productive tool life and broad material applicability. Order the P3201-D31.75 WHH15X through Metav Werkzeuge or request advice from the technical consultants. P3201-D31.75 WHH15X milling indexable insert — D31.75 chipbreaker, Walter Tools P3201-D31.75 WHH15X is a versatile milling insert designed for efficient metalcutting applications in general machining environments Coated cemented carbide grade WHH15X D31.75 chipbreaker geometry Designed for versatile milling tasks Walter Tools quality and consistency Consistent chip control for reliable productivity The coated cemented carbide substrate in this insert, specified as WHH15X, is engineered to provide stable chip formation under varying cutting conditions. The built-in chipbreaker D31.75 shapes and evacuates chips to reduce recutting and to lower thermal load on the cutting edge, which in turn preserves cutting performance over longer cycles. For production settings this means fewer interruptions, more predictable cycle times and a measurable improvement in machining throughput. The geometry is documented to suit common face and shoulder milling operations where controlled chip flow is essential. Clear guidance on materials and suitable applications Based on the available grade data, the insert is a coated cemented carbide type and should be selected with reference to the specific workpiece material matrix. The insert is intended for general milling tasks across a broad range of ferrous and non-ferrous components; users are advised to verify the WHH15X grade against the intended material and cutting conditions. Where higher abrasion resistance or different surface-finish targets are required, a comparison with alternative grades is recommended. The specification supports flexible use in both single-pass and multi-pass operations when matched to appropriate cutting data. Process security and extended tool life The combination of a modern coating system and the WHH15X grade is aimed at enhancing edge stability and wear resistance. This results in repeatable performance and reduced frequency of index changes, which supports higher overall equipment effectiveness. In automated cells or batch production, the improved consistency reduces variability between parts and helps maintain target tolerances. Where process reliability is a priority, the insert’s characteristics contribute to predictable tool-change intervals and lower unplanned downtime. Practical handling and procurement benefits The insert’s standard designation ensures straightforward identification and replacement in tool management systems. Its compatibility with common clamping modules and holders simplifies inventory handling and reduces set-up time on machines. The open-series classification of the grade facilitates quick selection from stock ranges, supporting short lead times in replenishment. Documentation and grade data are supplied as catalogue information, enabling specification checks prior to deployment in critical operations. For application-specific recommendations or to source Walter Tools P3201-D31.75 WHH15X inserts, contact Metav Werkzeuge for expert guidance and order placement via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: P3201-D31.75-WHH15X-WALTER Name: P3201-D31.75 WHH15X Product type: Milling indexable insert Manufacturer: Walter Tools Facts Chipbreaker designation: D31.75 Grade designation: WHH15X Special features Coated cemented carbide Series: Walter grade range – open series Material information: Catalogue dependent FAQ What is the primary application of this insert? The insert is intended for general milling applications where chip control and edge stability are required; the WHH15X grade supports a broad range of machining tasks. Which chipbreaker is fitted to the insert and what benefit does it provide? The D31.75 chipbreaker offers controlled chip formation and evacuation, which reduces recutting and helps maintain cutting-edge integrity during milling. How should the WHH15X grade be selected for specific materials? Grade selection should be made by consulting the WHH15X product matrix and matching coating and substrate properties to the workpiece material and cutting conditions. Manufacturer: Walter Tools (Walter AG); Headquarters: Tübingen, Germany; Part of the Sandvik Group Protected trademarks and product names are the property of their respective owners. Brand names and registered trademarks are mentioned for clarification only and do not imply any connection between Metav Werkzeuge and the named manufacturers. The offered item is an original, factory-new product from the stated manufacturer.
P3201-D32 WHH15X Wendeplatten - Walter Tools
Take advantage of reliable chip control and the WHH15X coated carbide grade to increase machining stability and productivity; the D32 chipbreaker supports consistent machining results. Order the P3201-D32 WHH15X directly via Metav Werkzeuge or consult the team for application guidance. P3201-D32 WHH15X Walter Tools milling indexable insert — chipbreaker D32, coated carbide grade WHH15X The P3201-D32 WHH15X is a precision milling indexable insert designed for productive milling operations where consistent chip formation and long-lasting cutting performance are required. Coated carbide grade WHH15X Chipbreaker D32 for repeatable chips Designed for productive milling operations Reliable chip control that stabilises production The D32 chipbreaker is engineered to deliver predictable chip formation, reducing the risk of entangling chips or unexpected tool interruptions. Predictable chips mean fewer stoppages and less manual cleaning of the work area, which supports continuous operation and improved cycle times. In practice, selecting the correct chip control geometry directly lowers rework rates and contributes to a steadier process flow on series and batch milling tasks. Coated carbide grade for enhanced wear resistance The insert is supplied in the WHH15X coated carbide grade, a coated hardmetal variant that combines hardness with surface protection to resist abrasive and adhesive wear. This results in a longer usable life of the cutting edge under comparable cutting conditions, enabling higher cumulative cutting lengths before reconditioning is required. For customers assessing tooling economics, the combination of robust coating and cutting geometry often leads to a favourable productivity-to-cost ratio. Practical application and integration advice This indexable insert is classified in the Walter Schneidstoffsorte series and the WHH15X grade; material suitability should be verified against the official product matrix before selection. The designation and chipbreaker code assist in ensuring the insert matches the cutter body and intended process parameters. When integrating into production, ensure the insert seat and clamping torque are correct to preserve the cutting edge and maintain repeatable runout performance. Contact Metav Werkzeuge for an expert assessment on using the Walter Tools P3201-D32 WHH15X in your milling operations and for tailored recommendations Technical data Article number: P3201-D32-WHH15X-WALTER Designation: P3201-D32 WHH15X Product type: milling indexable insert Grade: WHH15X Chipbreaker: D32 Manufacturer: Walter Tools Material: Katalogabhängig Series: Walter Schneidstoffsorte - Serie offen Facts Chipbreaker code: D32 SKU: P3201-D32-WHH15X-WALTER Special features Coating: coated carbide (WHH15X) Material: Katalogabhängig Sorteneinsatz: Check product matrix for material suitability Series: Walter Schneidstoffsorte - Serie offen WPL designation: P3201-D32 WHH15X FAQ What materials is this insert suitable for? The P3201-D32 WHH15X is supplied in the WHH15X coated carbide grade; material suitability must be checked against the manufacturer’s product matrix to confirm compatibility with specific steels, alloys or non-ferrous materials. How does the D32 chipbreaker affect machining? The D32 chipbreaker provides controlled chip formation, improving chip control and reducing interruptions—this enhances process stability during milling operations with the insert. Can this insert be used with multiple cutter bodies? The insert’s designation P3201-D32 WHH15X identifies geometry and chipbreaker; compatibility is determined by matching the insert seat and clamping system of the cutter body to that designation. Is the WHH15X grade coated and what is the benefit? Yes, WHH15X is a coated carbide grade that increases wear resistance and can extend the effective life of the cutting edge under appropriate cutting conditions. Where can one obtain precise selection guidance for this insert? Metav Werkzeuge can provide detailed selection advice; the P3201-D32 WHH15X product matrix and process parameters should be reviewed for the intended application. Protected trademarks and product names are the property of their respective owners. Brand names and registered trademarks are mentioned for identification and explanatory purposes only. No connection between our company and the referenced brands is implied. The offered article is original factory-new goods of the manufacturer Walter Tools. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
P3204-D07.94 WHH15X Wendeplatten - Walter Tools
Take advantage of the proven combination of coated carbide performance, the D07.94 chipbreaker and Walter Tools' production quality for consistent, productive milling cycles; order or request application advice via Metav Werkzeuge for tailored process support. P3204-D07.94 WHH15X indexable milling insert (Fräswendeschneidplatte) by Walter Tools — coated carbide, D07.94 chipbreaker P3204-D07.94 WHH15X is an indexable milling insert designed for general milling tasks where a robust coated carbide grade and reliable chip control are required Coated carbide grade WHH15X D07.94 chipbreaker for stable chip formation Versatile indexable milling insert for multiple operations Manufactured by Walter Tools Optimised machining performance for higher throughput The combination of a coated carbide grade and a dedicated D07.94 chipbreaker delivers measurable improvements in machining stability and process reliability. The insert's geometry and coating support steady cutting conditions, which reduces the frequency of tool changes and minimises downtime. As a result, the insert contributes directly to productive machining, with benefits for cycle times and machine utilisation. For production environments seeking consistent performance, this insert helps maintain repeatable results and lowers overall machining overheads. Flexible application scope with clear selection guidance This indexable insert is provided in the WHH15X grade, a coated hardmetal formulation intended for a broad range of milling tasks. The grade and chipbreaker combination support dependable chip control across various workpiece materials, but material suitability must be checked against the product matrix for exact applications. Where material-specific recommendations are required—such as for non-ferrous alloys or hardened steels—consult the technical matrix to confirm optimal cutting data. Clear selection avoids inappropriate use and ensures the best balance of tool life and surface finish. Durable design and economical use in production A coated hardmetal insert such as this one offers improved wear resistance and edge stability compared with uncoated grades; that translates into longer effective cutting life and fewer interruptions for index changes. The stable chip formation engineered into the chipbreaker reduces built-up edge and heat concentration, supporting consistent surface quality and repeatable component tolerances. When combined with sound cutting parameters and correct toolholders, users can expect improved tool life and lower per-part tooling costs, reinforcing the insert's role in efficient machining strategies. For tailored advice on integrating the P3204-D07.94 WHH15X indexable insert from Walter Tools into existing processes or to request procurement assistance, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for prompt support. Technical Data SKU: P3204-D07.94-WHH15X-WALTER Article designation: P3204-D07.94 WHH15X Product type: Fräswendeschneidplatte (indexable milling insert) Brand: Walter Tools Data Chipbreaker: D07.94 Grade/Sort: WHH15X Series: Walter Schneidstoffsorte - Serie offen Special features Coating: coated hardmetal (beschichtetes Hartmetall) Material specification: catalogue-dependent Note: check product matrix for material suitability Intended function: indexable milling with stable chip control FAQ What materials is the P3204-D07.94 WHH15X suitable for? The WHH15X grade is a coated hardmetal intended for a wide range of milling applications; however, specific material suitability should be verified in the product matrix before application to ensure optimal results with the P3204-D07.94 WHH15X indexable milling insert from Walter Tools. What is the purpose of the D07.94 chipbreaker? The D07.94 chipbreaker is engineered to promote stable chip formation and reliable chip evacuation, reducing the risk of built-up edge and improving surface consistency when using the WHH15X insert. Can the insert be used for high-speed machining? The coated hardmetal construction supports elevated cutting performance, but suitability for high-speed machining depends on the workpiece material and cutting parameters; consult the product matrix and machining guidelines for the P3204-D07.94 WHH15X. How does the WHH15X grade affect tool life? WHH15X is a coated grade designed to improve wear resistance and edge stability, which typically extends tool life under proper cutting conditions and supports more consistent productivity in milling operations. Which toolholders are compatible with this insert? Compatibility depends on the insert shape and the chosen milling cutter system; verify seat form and clamping method with the cutter supplier and the insert designation P3204-D07.94 WHH15X to ensure correct fit. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Trademarks and trade names are the property of their respective owners. The mentioned brand is cited for clarification; there is no affiliation implied between our company and the named brand. The offered article is an original, factory-new product of the manufacturer.
P3204-D07.94 WSP46G Wendeplatten - Walter Tools
Take advantage of Tiger‑tec Gold performance and the versatile WSP46G grade for reliable milling of steel, stainless steel and high‑temperature alloys; the combination of a proven PVD‑coated carbide grade and a dedicated D07.94 chipbreaker supports consistent productivity and predictable tool life. Order directly via Metav Werkzeuge or request application advice from their consultants. P3204-D07.94 WSP46G milling indexable insert (Tiger‑tec Gold) by Walter Tools A P3204-D07.94 WSP46G milling indexable insert engineered for versatile face and peripheral milling of steel, stainless steel and heat‑resistant alloys Tiger‑tec Gold PVD coating Versatile for P / M / S materials Stable cutting edge for milling Optimised chip control D07.94 High‑performance grade for productive milling The Tiger‑tec Gold family combines a hard, wear‑resistant coating with a tough substrate to deliver a PVD‑coated carbide solution that balances abrasion resistance and edge stability. As a result, the WSP46G grade reduces flank wear under typical milling temperatures and supports longer, more predictable tool life. For production environments this translates into fewer insert changes, lower machine downtime and improved net machining output per tool. Consistent chip control and edge reliability The integrated D07.94 chipbreaker manages chip formation across a wide material range, promoting controlled chip evacuation and reduced recutting. This stability is particularly valuable when machining stainless steel and superalloys/titanium, where built‑up edge and poor heat dissipation can compromise surface finish. The combination of grade and geometry delivers a secure cutting edge, improved surface integrity and a lower risk of thermal damage during demanding milling cycles. Application focus and measurable process benefits Designed for general and finishing milling operations, the insert suits applications in component production where both surface quality and repeatability matter. The designation P / M / S indicates suitability for steel, stainless steel and heat‑resistant alloys respectively; this simplifies tool selection across mixed‑material production runs. Using a dedicated PVD grade such as this can result in fewer rejects, steadier cycle times and better overall machining economy. For application queries or process optimisation, Metav Werkzeuge offers technical advice and practical recommendations. For tailored application guidance or to specify P3204‑D07.94 WSP46G inserts for a production setup, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: P3204-D07.94-WSP46G-WALTER Description: Fräswendeschneidplatte P3204-D07.94 WSP46G Walter Tools Manufacturer: Walter Tools Facts SKU: P3204-D07.94-WSP46G-WALTER Series: Tiger‑tec Gold Insert designation: P3204-D07.94 WSP46G Special features Coating: Tiger‑tec Gold (PVD) Grade: WSP46G (PVD‑coated carbide) Applicable material groups: Steel (P), Stainless steel (M), Superalloys/Titanium (S) FAQ What materials can be machined with this insert? The P3204‑D07.94 WSP46G insert is suitable for steel, stainless steel and heat‑resistant alloys (P / M / S), making it a versatile choice for mixed‑material production. What benefit does the Tiger‑tec Gold coating provide? The Tiger‑tec Gold PVD coating enhances wear resistance and thermal stability for the insert, improving tool life and surface finish in demanding milling operations. What does D07.94 refer to? D07.94 identifies the chipbreaker geometry designed to deliver controlled chip formation and reliable chip evacuation during face and peripheral milling. Is this insert intended for roughing or finishing? The grade and geometry of the insert support both general milling and finishing tasks; selection of cutting parameters determines the balance between metal removal rate and surface quality. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned solely for explanation; there is no connection between our company and the named brands. The offered article is original, factory‑new goods of the manufacturer (Walter Tools).
P3204-D08 WHH15X Wendeplatten - Walter Tools
Leverage the combination of coated carbide durability, precise chip control and adaptable open-series performance for reliable milling results. The proven D08 chipbreaker and WHH15X grade deliver consistent cutting behaviour across a wide range of tasks; Order the P3204-D08 WHH15X milling insert directly via Metav Werkzeuge or ask our consultants if needed. P3204-D08 (P3204-D08 WHH15X) WHH15X milling insert by Walter Tools — D08 chipbreaker, coated carbide P3204-D08 WHH15X is a compact, industrial-grade milling indexable insert intended for productive finishing and general-purpose milling where consistent chip formation and edge stability are required. Milling insert P3204-D08 WHH15X by Walter Tools Coated carbide grade WHH15X for wide workpiece range D08 chipbreaker for predictable chip control Open-series grade for flexible machining strategies Stable cutting performance for dependable cycle times The combination of a coated carbide grade and a defined D08 chipbreaker provides a reliable balance between wear resistance and controlled chip formation. As an indexable insert, this specification focuses on repeatable edge geometry and consistent tool life, reducing downtime for edge changes and part rework. The WHH15X grade is described as a coated hardmetal and belongs to Walter’s open series, which is aimed at broad applicability rather than a single optimised material. For purchasers, this translates into fewer tool variants to stock and predictable machining behaviour in mixed-production environments. Improved surface quality through effective chip control A precise chipbreaker geometry such as D08 reduces the risk of long, entangling swarf and promotes uniform evacuation of chips from the cut. This has a direct effect on finished-part quality: more consistent surface texture and fewer marks that require additional finishing. The insert’s design supports stable cutting conditions even when machine rigidity or part clamping varies. Explaining technical terms: coated carbide means a hardmetal substrate with a protective, wear-resistant coating that extends flank and crater life; chipbreaker describes the topography that shapes and fractures chips during cutting. These elements together reduce the frequency of intervention and support steady production output. Application flexibility and selection guidance The WHH15X specification is part of Walter’s open series; this implies a focus on versatility rather than being optimised for a single alloy class. Manufacturers are advised to verify workpiece suitability against the product matrix: the grade and geometry deliver broad coverage, but the final selection should consider material, cut depth and feed. Where high-speed finishing or tight tolerances are required, matching feed and speed to the insert’s recommended parameters will preserve edge life and surface finish. In practice, the insert suits mixed runs and general finishing operations where reproducibility and simple tool management are priorities. Contact Metav Werkzeuge for tailored machining advice and reliable supply of Walter Tools P3204-D08 WHH15X milling inserts — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 Technical data Article number: P3204-D08-WHH15X-WALTER Name: Milling indexable insert P3204-D08 WHH15X Walter Tools Product type: Milling indexable insert Grade: WHH15X Facts ISO designation: P3204-D08 WHH15X Chipbreaker: D08 Series: Walter Schneidstoffsorte - Serie offen Identifier: P3204-D08-WHH15X-WALTER Special features Coated carbide (beschichtetes Hartmetall) Open-series grade for adaptable use Designed for consistent chip control Workpiece suitability: consult product matrix Manufacturer: Walter Tools FAQ What materials is the P3204-D08 WHH15X suitable for? The P3204-D08 WHH15X is a coated carbide grade designed for a broad range of materials; final suitability should be checked against the product matrix to ensure optimal performance. How does the D08 chipbreaker influence machining? The D08 chipbreaker promotes predictable chip fracture and evacuation, improving surface finish and reducing swarf-related interruptions when using the P3204-D08 WHH15X insert. Can this insert be used for finishing applications? Yes, the WHH15X grade and the insert geometry support finishing operations where consistent surface quality and edge life are required. What distinguishes the WHH15X grade from other grades? WHH15X is a coated hardmetal formulation within Walter’s open series, offering wear resistance and a balance of toughness for varied machining tasks. How should the correct insert variant be chosen for a job? Selection should consider material, required surface finish and cutting parameters; the P3204-D08 WHH15X is suited to flexible, general-purpose applications but matching to the product matrix ensures best results. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand presentation: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and forms part of the Sandvik Group. Protected trademarks and product names are the property of their respective owners and are mentioned here for explanation only. There is no affiliation between our company and the trademark owners. The offered item is an original, factory-new product of the manufacturer.
P3204-D08 WSM36G WSM36G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, robust WSM36G grade and optimised chip control for consistent productivity and longer tool life. The insert suits demanding materials such as stainless steels and heat‑resistant superalloys, reducing downtime and tool changes. Order the P3204‑D08 WSM36G directly via Metav Werkzeuge or contact our consultants for application support. P3204‑D08 WSM36G milling insert — coated carbide for stainless steels and superalloys (Walter Tools) The P3204‑D08 WSM36G is a coated carbide milling insert engineered for productive face and peripheral milling in stainless steels and heat‑resistant superalloys, benefitting workshops that require stable cutting edges and reliable chip formation. Tiger·tec Gold coating for longer life Optimised chip control D08 geometry Suitable for stainless steels and superalloys Stable cutting edge for productive milling Higher throughput through proven coating and grade The combination of the Tiger·tec Gold coating and the WSM36G grade provides a marked increase in process security when machining tough materials. As a coated carbide solution, the insert supports controlled wear progression and thermal resistance, which translates into fewer unexpected tool changes and more predictable tool life. The D08 chipbreaker geometry is optimised for consistent chip control, reducing the risk of built‑up edge and improving machining stability on materials that tend to work‑harden. This results in better machine utilisation and lower per‑part tooling costs. Practical workshop benefits: consistent edges and surface quality Workshops gain practical benefits from the insert’s design: the stable cutting edge reduces margin for error and supports repeatable surface finishes with fewer passes. The insert’s specification emphasises productivity and reproducibility, making it suitable for batch production or challenging single‑piece flow. Because the geometry and coating are tuned for demanding alloys, operators achieve improved surface finish and dimensional consistency, while maintenance intervals can be extended thanks to lower flank wear rates. Application guidance and selection criteria The insert is aimed at machining tasks involving stainless steels (ISO group M) and heat‑resistant superalloys or titanium (ISO group S), where heat generation and edge loading are critical factors. For best results, pair the insert with appropriate cutting parameters and a coolant strategy adapted to the workpiece and machine rigidity. Walter Tools’ Tiger·tec Gold technology excels in environments where thermal stability and edge integrity determine productivity; consult Metav Werkzeuge for recommended feeds and speeds for specific alloys. For a tailored assessment of suitability and cutting data for the Walter Tools P3204‑D08 WSM36G, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application details and secure supply. Technical data Article number: P3204-D08-WSM36G-WALTER Product type: Fräswendeschneidplatte / milling insert ISO designation: P3204‑D08 WSM36G Series: Tiger·tec Gold Grade: WSM36G Core data Material class: coated carbide Application groups: S / M Chipbreaker: D08 Special features Designed for stainless steels and superalloys Coating technology: Tiger·tec Gold Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The P3204‑D08 WSM36G is designed primarily for stainless steels (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), offering thermal stability and stable edge behaviour in these materials. How does the Tiger·tec Gold coating help in production? The Tiger·tec Gold coating on the WSM36G grade increases wear resistance and thermal stability, which helps to extend tool life and maintain consistent performance in demanding milling operations. What does the D08 chipbreaker mean for chip control? The D08 chipbreaker geometry promotes reliable chip segmentation and evacuation, reducing the risk of built‑up edge and improving process stability during milling of difficult‑to‑machine alloys. Where can cutting data and application advice be obtained? Cutting recommendations and application advice for the P3204‑D08 WSM36G are available from Metav Werkzeuge; they can advise on feeds, speeds and coolant strategies for specific materials and machine setups. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered article is an original, factory‑new product of the manufacturer (Walter Tools).
P3204-D08 WSP46G WSP46G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the D08 chipbreaker for reliable, long-lasting milling performance; order the insert directly via Metav Werkzeuge or consult the technical team for application-specific advice. P3204-D08 WSP46G milling insert – Tiger·tec Gold coating, D08 chipbreaker (Walter Tools) A P3204-D08 WSP46G milling insert designed for versatile milling of Stahl, rostfreier Stahl and heat-resistant alloys in demanding production environments Tiger·tec Gold coating for extended tool life WSP46G PVD-coated carbide for versatile performance D08 chipbreaker optimised for stable chip control Suitable for Stahl, rostfreier Stahl and superalloys Longer productive service life through advanced coating technology The insert is equipped with the Tiger·tec Gold coating, a multi-layer PVD system that provides improved wear resistance and thermal stability. This results in a longer tool life and reduced changeover frequency, which translates directly into higher machine uptime and lower unit costs per component. The WSP46G grade combines toughness with surface protection, making the geometry and coating pairing particularly effective for interrupted cuts and mixed material batches common in industrial milling. Consistent chip formation and edge stability for predictable machining Thanks to the D08 chipbreaker geometry, the insert ensures controlled chip formation across a wide range of cutting conditions. Stable chip control reduces the risk of built-up edge and minimises tool-related surface defects, supporting repeatable component quality. The combination of the chipbreaker and a robust cutting edge promotes smooth power draw and helps preserve spindle life, which is especially beneficial in automated cell environments where consistency is essential. Broad material capability reduces tool variants and simplifies inventory Specifically developed for the P / M / S application groups, this grade suits machining of Stahl, rostfreier Stahl and difficult-to-cut superalloys including titanium-based materials. The versatility of the WSP46G grade reduces the need for multiple specialised inserts, simplifying stock management while maintaining machining performance across different workpiece materials. For process planners, this means fewer tool changes and streamlined setup times without compromising on surface finish or dimensional accuracy. Practical benefits in production planning and process security Integrating this insert into production offers tangible process advantages: improved tool life lowers tooling costs per part, predictable wear behaviour supports scheduled maintenance, and the robust PVD coating reduces sensitivity to higher cutting temperatures. The design intent is clear—deliver repeatable performance under industrial cutting loads while enabling efficient machining strategies and consistent component quality. Contact Metav Werkzeuge today at info@metav-werkzeuge.com or +49 2822 7131930 to discuss the P3204-D08 WSP46G insert from Walter Tools and receive tailored application recommendations Technical Data Article number: P3204-D08-WSP46G-WALTER Designation: P3204-D08 WSP46G Series: Tiger-tec Gold Product type: Fräswendeschneidplatte / milling insert Manufacturer: Walter Tools Facts Material groups: P / M / S Chipbreaker: D08 Coating: Tiger·tec Gold (PVD) Grade: WSP46G Special features PVD-coated carbide for toughness and wear resistance Optimised for interrupted cuts and mixed batches Stable cutting edge for predictable tool life Broad workpiece coverage: Stahl, rostfreier Stahl, superalloys FAQ What materials is the insert suitable for? The P3204-D08 WSP46G insert is suitable for machining Stahl, rostfreier Stahl and heat-resistant superalloys, reflecting its design for P / M / S material groups. How does the Tiger·tec Gold coating benefit production? The Tiger·tec Gold PVD coating on the WSP46G grade improves wear resistance and heat tolerance, resulting in longer tool life and fewer tool changes in demanding milling applications. What role does the D08 chipbreaker play? The D08 chipbreaker is optimised for stable chip control and reduced built-up edge, supporting consistent surface finish and more predictable tool behaviour during milling operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned solely for explanatory purposes. There is no affiliation between our company and the listed brands. The offered item is original, factory-new goods of the manufacturer; Walter Tools is used here for identification and clarification purposes.
P3204-D09.52 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide performance, a D09.52 chipbreaker for consistent chip formation and the Walter open series for flexible milling strategies; order via Metav Werkzeuge or consult our team for selection and compatibility advice. Fräswendeschneidplatte P3204-D09.52 WHH15X — milling indexable insert, Walter Tools P3204-D09.52 WHH15X is a milling indexable insert designed for industrial metalworking where controlled chip formation and dependable edge performance are required Coated carbide grade WHH15X Chipbreaker D09.52 for consistent chips Open series for flexible milling strategies Catalogue-dependent grade and sizing Durable coated carbide for steady production The insert uses a coated carbide grade (WHH15X) that provides wear resistance and stable cutting behaviour under intermittent milling conditions. A coated carbide insert combines a hard carbide core with a thin, engineered coating that reduces friction at the cutting edge and slows abrasive wear; this yields longer tool life and reduced tool-change frequency, which supports higher productivity and lower running costs. As the grade is specified as WHH15X within the Walter series, material suitability should be verified against the manufacturer’s product matrix before final selection to ensure optimal cutting parameters and expected performance. Consistent chip control and improved surface finish The integrated chipbreaker D09.52 is engineered to shape chips reliably during milling operations, reducing entanglement and simplifying waste handling. Effective chip control lowers the risk of recutting and helps maintain an even cutting load, which contributes to a better surface finish and fewer interruptions on the shop floor. In practical terms, a well-matched chipbreaker reduces manual intervention, shortens cycle times and supports automated processes. For process technicians, recognising the chipbreaker designation (D09.52) enables straightforward adjustment of feed and speed to achieve stable cutting conditions. How to assess compatibility and integrate the insert Selection should follow a brief evaluation of workpiece material and machining strategy: check the Walter series classification and the product matrix for the WHH15X grade, match the insert geometry to the cutter body and verify clamping and seating dimensions. The open series designation indicates design versatility across different milling tasks, but specific application limits depend on cutter body, depth of cut and spindle power. For engineering teams seeking predictable results, pairing the insert with well-documented cutting data and a validated toolholder will enhance process stability and extend tool life while maintaining component quality. For technical selection and ordering of Walter Tools inserts such as the WHH15X grade, contact Metav Werkzeuge GmbH for tailored advice and availability via info@metav-werkzeuge.com or +49 2822 7131930. Technical Data Article number: P3204-D09.52-WHH15X-WALTER SKU: P3204-D09.52-WHH15X-WALTER Designation: P3204-D09.52 WHH15X Product type: Fräswendeschneidplatte (milling indexable insert) Brand: Walter Tools Grade designation: WHH15X Chipbreaker: D09.52 Series: Walter Schneidstoffsorte - Serie offen Material: Katalogabhängig Core specifications Chipbreaker code: D09.52 Cutting material class: coated carbide Series name: Walter Schneidstoffsorte - Serie offen Grade: WHH15X Special features Coated carbide cutting material Designed for controlled chip formation Open series for broad milling applications Material suitability to be checked via product matrix FAQ What does the WHH15X grade indicate for performance? The WHH15X grade denotes a coated carbide Walter Tools cutting grade optimised for wear resistance and steady performance; consult the product matrix for exact material recommendations for the P3204-D09.52 WHH15X insert. How does the D09.52 chipbreaker affect machining? The D09.52 chipbreaker shapes chips to improve chip control, reduce recutting and support a consistent surface finish when using the P3204-D09.52 WHH15X insert in appropriate milling setups. Can this insert be used across different workpiece materials? The insert belongs to an open Walter series and may be versatile, but material suitability depends on the specific grade matrix; verify the WHH15X recommendations before applying the insert to a new material or process. How should the insert be integrated into an existing milling system? Match the P3204-D09.52 WHH15X insert to a compatible toolholder and cutter body, set cutting data according to Walter’s guidance and ensure secure clamping to achieve the stated process stability and tool life benefits. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only and do not imply any affiliation between Metav Werkzeuge and the trademark owners. The offered item is an original, factory-new product of the manufacturer (Walter Tools).
P3204-D09.52 WSM36G WSM36G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WSM36G grade for reliable performance when machining demanding alloys, ensuring longer tool life and consistent chip control; order Walter Tools inserts through Metav Werkzeuge or consult their specialists for application advice. P3204-D09.52 WSM36G milling insert — Walter Tools, Tiger·tec Gold, D09.52 chipbreaker The P3204-D09.52 WSM36G is a coated carbide milling insert designed for heavy-duty and high-temperature applications, particularly suited to rostfreier Stahl and heat-resistant superalloys in demanding milling operations. Tiger·tec Gold coating for improved wear resistance WSM36G grade for rostfreier Stahl and superalloys D09.52 chipbreaker for secure chip control Designed for productive milling operations Longer life through advanced coating technology The combination of Tiger·tec Gold and the WSM36G carbide grade provides a marked increase in wear resistance and edge stability under elevated temperatures. As a coated carbide insert, it delays flank and crater wear, which translates into fewer tool changes and reduced process interruptions. For production environments where consistent cycle times and predictable tool life are essential, this coating and grade pairing supports extended uninterrupted machining, lowering overall tooling costs while maintaining component quality. Secure chip control and surface integrity in tough materials The D09.52 chipbreaker geometry is engineered to promote reliable chip control and to prevent built-up edge formation when cutting sticky or gummy alloys. When machining rostfreier Stahl or heat-resistant superalloys, controlled chip formation reduces heat concentration at the cutting zone and helps achieve a consistent surface finish. The chipbreaker design also supports stable cutting forces, which benefits machine tool uptime and enables more predictable process parameters for high-volume milling tasks. Productivity gains and process security for production milling This insert is intended for productive milling strategies where repeatability and process security matter most. The combination of grade and geometry delivers stable cutting edges that tolerate thermal and mechanical loads, enabling higher feed rates and longer tool life compared with uncoated grades. By choosing an insert from Walter Tools’ Tiger·tec Gold family, production engineers gain improved material removal rates and fewer secondary operations, helping to meet throughput targets without compromising component tolerances. Application guidance and ISO-oriented suitability The insert’s designation aligns with ISO group classifications relevant to its intended use: the grade supports the ISO group M (rostfreie Stähle) and S (heat-resistant superalloys and titanium). In practice, that means the insert is suitable for materials that demand thermal resistance and strong edge integrity; appropriate cutter geometries and cutting parameters should be selected to match the workpiece and machine capabilities. For mixed-production environments, the insert provides a flexible option where both rostfreier Stahl and high-temperature alloys are machined. For reliable high-performance milling with Tiger·tec Gold inserts from Walter Tools, contact Metav Werkzeuge for tailored application support or to secure stock of P3204-D09.52 WSM36G inserts through Metav Werkzeuge. Technical data Article number: P3204-D09.52-WSM36G-WALTER SKU: P3204-D09.52-WSM36G-WALTER Product designation: P3204-D09.52 WSM36G Facts Series: Tiger·tec Gold Grade: WSM36G Chipbreaker: D09.52 Material groups: S / M Special features Coating: Tiger·tec Gold Material: coated carbide Application: rostfreier Stahl and heat-resistant superalloys Product type: milling insert (Fräswendeschneidplatte) Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The P3204-D09.52 WSM36G milling insert from Walter Tools is suitable for rostfreier Stahl and heat-resistant superalloys, matching its design intent for the ISO M and S material groups. How does the Tiger·tec Gold coating help in production? The Tiger·tec Gold coating on the WSM36G grade increases wear resistance and thermal stability, enabling longer tool life and more consistent performance during continuous milling of demanding alloys. What benefit does the D09.52 chipbreaker provide? The D09.52 chipbreaker format promotes controlled chip formation and reduced built-up edge, which helps maintain surface quality and reduces the risk of process instability when machining sticky materials. Can this insert be used for titanium alloys? Yes; the WSM36G grade and geometry are designed to work with the ISO S group, which includes titanium and other heat-resistant superalloys, provided cutting parameters are adapted accordingly. Is the insert compatible with high-feed milling strategies? The combination of the WSM36G grade and Tiger·tec Gold coating offers the stability and wear resistance needed for productive milling approaches; tuning feeds and speeds to the machine and workpiece will achieve optimal results. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is an original factory-new product of the manufacturer.
P3204-D09.52 WSP46G WSP46G Wendeplatten - Walter Tools
Take advantage of the high-performance Tiger‑tec Gold coating and the versatile WSP46G grade for reliable milling across diverse materials; the D09.52 chipbreaker ensures controlled chip formation and consistent surface finishes. Order directly via Metav Werkzeuge or contact the consultants for process-matched recommendations. P3204-D09.52 WSP46G milling insert — Tiger‑tec Gold by Walter Tools P3204-D09.52 WSP46G is a coated indexable insert for high-demand milling applications, designed for productive machining of Stahl, rostfreier Stahl and heat-resistant alloys Tiger‑tec Gold PVD coating Versatile for Stahl, rostfreier Stahl and superalloys D09.52 chipbreaker for reliable chip control Walter Tools grade WSP46G for extended edge life Maximise tool life with Tiger‑tec Gold The Tiger‑tec Gold PVD coating combines thermal resistance and wear protection to extend cutting-edge lifetime under continuous milling. The combination of a wear-resistant coating and a tough substrate supports stable cutting edges, which reduces the frequency of insert changes and contributes to predictable cycle times. For production environments this means fewer interruptions and improved overall tool economy while maintaining consistent component quality. Stable chip control for safer, faster milling Equipped with the D09.52 chipbreaker, this insert promotes secure chip formation and evacuation during slotting and face milling operations. Controlled chips reduce the risk of re-cutting and protect the machined surface, leading to improved surface integrity and fewer secondary processes. The engineered chip geometry supports reliable swarf flow, which is particularly beneficial when machining sticky or heat-sensitive materials. Versatility across key engineering materials The WSP46G grade is formulated for broad applicability: optimised for machining Stahl, rostfreier Stahl and demanding high-temperature alloys. That material range allows shops running mixed-production batches to standardise on a single insert type, simplifying tool inventory and reducing setup complexity. The grade’s balanced toughness and hardness deliver repeatable performance where both edge stability and wear resistance are required. Integration into production and handling benefits This indexable insert fits standard P3204-style milling cutters and is supplied as a ready-to-fit cutting edge solution. The clear designation and proven Walter Tools manufacturing ensure traceable quality and straightforward tool management. When combined with appropriate cutter bodies and cutting parameters, the insert supports efficient material removal rates and predictable surface finishes for series production. Contact Metav Werkzeuge for an application-specific recommendation on the Walter Tools Tiger‑tec Gold WSP46G inserts and for ordering assistance: info@metav-werkzeuge.com | +49 2822 7131930 — technical consulting and delivery options available. Technical data Article number: P3204-D09.52-WSP46G-WALTER Product name: P3204-D09.52 WSP46G Product type: milling indexable insert Brand: Walter Tools Facts Series: Tiger‑tec Gold Grade: WSP46G Chipbreaker: D09.52 Suitable material groups: P / M / S (Stahl, rostfreier Stahl, superalloys / titanium) Special features Coating: Tiger‑tec Gold (PVD-coated) Substrate: coated carbide Typical applications: slotting, face milling, general milling operations Designed for productivity and stable edge life FAQ What materials can be machined with this insert? The P3204-D09.52 WSP46G insert is suitable for machining Stahl, rostfreier Stahl and heat-resistant superalloys, making it a versatile choice for mixed-production environments. How does the D09.52 chipbreaker improve milling performance? The D09.52 chipbreaker promotes controlled chip formation and reliable evacuation, which reduces re-cutting and supports consistent surface finish during milling. Is this insert compatible with standard P3204 cutter bodies? Yes, the designation indicates compatibility with P3204-style milling cutter systems; correct seating and clamping according to the cutter manufacturer’s instructions are recommended. What are the main benefits of the Tiger‑tec Gold coating? Tiger‑tec Gold offers enhanced thermal stability and wear resistance, which together extend cutting-edge life and contribute to predictable tool performance under production loads. Walter Tools — Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are used solely for descriptive purposes. There is no affiliation between Metav Werkzeuge and the trademark owners; the offered item is an original, factory-new product from the manufacturer.
P3204-D10 WHH15X Wendeplatten - Walter Tools
Benefit from the combination of the WHH15X coated cemented carbide grade and the D10 chipbreaker: consistent chip control and durable edge life reduce process variation and support efficient milling. Order the insert directly via Metav Werkzeuge or consult their specialists to verify material suitability against the product matrix. P3204-D10 WHH15X – indexable milling insert with D10 chipbreaker, Walter Tools The P3204-D10 WHH15X is an indexable milling insert engineered for controlled chip formation and stable cutting performance in general milling applications; suitability for specific workpiece materials should be verified using the product matrix. Coated cemented carbide grade WHH15X D10 chipbreaker for controlled chip formation Walter open-series cutting grade Material suitability per product matrix Stable chip control for reliable machining The D10 chipbreaker is designed to promote predictable chip separation, which leads to reduced risk of built-up edge and improved surface consistency. By combining a specifically profiled chip groove with a coated cemented carbide substrate, the geometry actively supports evacuation of chips under varying depths of cut. This results in fewer interruptions for chip clearing and a steadier machining cycle time, making production runs more predictable. Coating and grade that extend tool life The WHH15X designation denotes a coated cemented carbide cutting grade formulated for general-purpose machining within Walter’s open series. The coating enhances wear resistance and thermal stability at the cutting edge, which translates into longer edge life and fewer insert changes. For operations where tool-change time is costly, the wear-resistant surface reduces downtime and contributes to overall process economy. Clear guidance for application and compatibility This insert is supplied in the P3204-D10 form with the WHH15X grade; however, material suitability must be checked against the product matrix supplied by the manufacturer. The grade and chipbreaker combination is intended to cover a range of common machining tasks, but matching the cutting grade to the specific workpiece material and cutting parameters ensures the expected performance and longevity of the tool. Consistent brand quality and process security Walter Tools’ open-series grades are positioned to deliver consistent performance with an emphasis on stable chip formation and repeatable results. Where process security and surface quality are priorities, using a characterised cutting grade such as this one helps to standardise results across batches and operators. Selection based on the matrix supports efficient integration into existing machining strategies. For application advice or to confirm suitability of the WHH15X grade for a specific material, contact Metav Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 — Metav Werkzeuge can assist with selection and ordering of this Walter Tools insert. Technical Data Article number: P3204-D10-WHH15X-WALTER Designation: P3204-D10 WHH15X Product type: indexable milling insert Manufacturer: Walter Tools Facts Chipbreaker: D10 Grade: WHH15X Material: coated cemented carbide Special features Walter open-series cutting grade Material suitability to be checked via product matrix Coated cemented carbide for improved wear resistance FAQ What chip control benefits does this insert provide? The D10 chipbreaker promotes controlled chip formation and evacuation; the WHH15X coated cemented carbide grade supports consistent cutting and reduced built-up edge during milling. Is this insert suitable for all materials? Material compatibility must be verified using the product matrix; the WHH15X grade is a coated cemented carbide intended for a broad set of applications but requires confirmation for specific workpiece alloys. How does the coating improve performance? The coating on the WHH15X grade increases wear resistance and thermal stability of the cutting edge, which enhances tool life and maintains surface quality over longer runs. Can this insert be used in high-speed milling? The combination of chipbreaker geometry and coated cemented carbide supports efficient cutting; verify recommended cutting speeds and feeds against the product matrix for optimal performance. Walter Tools: Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden; support.coromant@sandvik.com. Protected trademarks and trade names remain the property of their respective owners. Mention of brand names serves explanatory purposes only; no affiliation between Metav Werkzeuge and the brands is implied. The offered article is original, factory-new goods of the manufacturer.
P3204-D10 WSM36G WSM36G Wendeplatten - Walter Tools
Benefit from extended tool life and reliable chip control combined with simple indexability for efficient face‑milling of demanding alloys; the P3204‑D10 WSM36G balances edge stability and heat resistance for consistent production. Order the P3204‑D10 WSM36G directly via Metav Werkzeuge or ask our consultants if needed. P3204‑D10 WSM36G milling indexable insert – Tiger·tec Gold coating, D10 chipbreaker (Walter Tools) A P3204‑D10 WSM36G milling insert engineered for heavy cutting and high‑temperature alloys, optimised for rostfreier Stahl and superalloys in face‑milling applications Tiger·tec Gold coated grade WSM36G D10 chipbreaker for stable chip control Suitable for rostfreier Stahl and superalloys High edge stability for productive machining Greater reliability when machining difficult alloys The Tiger·tec Gold coating in combination with the WSM36G carbide grade is designed to improve edge stability and wear resistance when working in high thermal load conditions. For materials that generate heat and sticky chips, such as rostfreier Stahl and heat‑resistant superalloys, this combination reduces the tendency for built‑up edge and premature flank wear. The result is a more predictable lifetime per index and fewer unplanned tool changes, which supports steady production rhythms and lower rework rates. Improved chip control and process security Integrated D10 chipbreaker geometry provides consistent chip formation and evacuation, which is crucial in heavy face‑milling where chip packing can damage the insert or workpiece. The optimised chip control stabilises forces on the cutting edge and helps maintain surface finish under varying cutting conditions. As a coated carbide insert with a robust cutting edge, this tool supports higher metal removal rates and a safer, more economical machining process when paired with an appropriate cutter body. Practical handling for workshop integration As an indexable insert, the P3204‑D10 WSM36G fits established cutter systems and is straightforward to replace and clamp, reducing downtime during tool changes. Selection of the right insert geometry and cutter body will determine the achievable feeds and cutting depths; the insert’s construction favours heavy‑cut applications and gives reliable behaviour across different batch sizes. For shops aiming to increase throughput on rostfreier Stahl and nickel‑based alloys, this solution brings process stability without complex parameter tuning. For application advice or to secure Walter Tools inserts, contact Metav Werkzeuge by eMail at info@metav-werkzeuge.com or phone +49 2822 7131930 — our specialists will advise on the right geometry and supply options Technical data Article number: P3204‑D10‑WSM36G‑WALTER Designation: P3204‑D10 ISO designation: P3204‑D10 WSM36G Facts Grade: WSM36G Series: Tiger·tec Gold Chipbreaker: D10 Applications & features Suitable for rostfreier Stahl (M) Suitable for superalloys and titanium (S) Coated carbide, optimised edge stability Manufacturer: Walter Tools FAQ Which materials can this insert machine effectively? The P3204‑D10 WSM36G is intended for rostfreier Stahl and heat‑resistant superalloys (S and M groups) and performs well where thermal load and toughness challenge the cutting edge. What benefit does the Tiger·tec Gold technology provide? Tiger·tec Gold coating on the WSM36G grade increases thermal resistance and wear protection, extending the useful life of the insert under demanding cutting conditions. How does the D10 chipbreaker affect performance? The D10 chipbreaker is optimised for stable chip formation and evacuation, reducing the risk of chip congestion and improving surface finish consistency during face‑milling operations. Is the insert suitable for heavy metal removal rates? Yes, the construction and edge stability of the P3204‑D10 WSM36G support productive heavy cutting when used with a compatible cutter body and appropriate machining parameters. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered marks are used for explanation only. There is no affiliation between our company and the named brands. The offer refers to original factory‑new products of the manufacturer.
P3204-D10 WSP46G WSP46G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold coating and the D10 chipbreaker for long tool life and consistent chip control; the result is reliable milling performance across steel, stainless steel and heat‑resistant alloys. Order the insert directly via Metav Werkzeuge or consult the team for application advice. P3204-D10 WSP46G milling indexable insert — Tiger‑tec Gold PVD, D10 chipbreaker — Walter Tools The P3204-D10 WSP46G is a coated carbide milling insert optimised for general and demanding milling tasks across a broad range of metals Tiger-tec Gold PVD coating Suitable for steel, stainless steel, superalloys Stable cutting edge for heavy milling D10 chipbreaker for reliable chip control Enhanced process security through advanced coating The combination of the Tiger‑tec Gold surface layer and a coated carbide substrate delivers improved resistance to flank wear and thermal loading, which translates into longer, more predictable tool life. The WSP46G grade is a tough, versatile PVD variety developed for milling, balancing edge stability with fracture resistance. For production environments where cycle time and uptime matter, the coating reduces abrasive wear and helps maintain a consistent cutting geometry over longer runs, supporting efficient, reproducible machining of ISO groups P, M and S. Consistent chip formation and surface quality The D10 chipbreaker is designed to shape and break chips reliably during transverse milling operations, reducing the risk of re-cutting and machine interference. Controlled chip formation contributes directly to a steadier cutting process and improved surface finish on the workpiece. When paired with the WSP46G grade, the insert supports stable edge behaviour under varying cutting forces, which is particularly advantageous for automated setups and mixed‑batch production where repeatability and minimal intervention are required. Versatile grade for a wide material spectrum This indexable insert is intended for machining steel, stainless steel and heat‑resistant superalloys including titanium alloys, offering a single‑grade option for diverse job shops and manufacturing cells. The WSP46G formulation emphasises toughness to withstand build‑up and notch formation, while the Tiger‑tec Gold elaborates thermal and tribological protection. Such a combination reduces the need for multiple grades across similar applications and aids planners in streamlining tool inventories without compromising on performance. For tailored selection and swift supply of Walter Tools Tiger‑tec Gold inserts, contact Metav Werkzeuge for technical consultation and order processing via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: P3204-D10-WSP46G-WALTER Label: Fräswendeschneidplatte P3204-D10 WSP46G Walter Tools Product type: Fräswendeschneidplatte / milling indexable insert Series: Tiger-tec Gold Grade: WSP46G Chipbreaker: D10 Material groups: P / M / S Manufacturer: Walter Tools UID: P3204-D10-WSP46G-WALTER Facts Chipbreaker designation: D10 Applicable ISO groups: P, M, S Special features Coating: Tiger-tec Gold (PVD) Substrate: coated carbide Application: milling Sort characteristics: tough, versatile for milling FAQ What materials can be machined with this insert? The P3204-D10 WSP46G insert is suitable for steel, stainless steel and heat‑resistant superalloys (ISO groups P, M and S), offering versatility across common milling tasks. How does the Tiger‑tec Gold coating benefit machining? The Tiger‑tec Gold PVD coating on the insert reduces abrasive wear and improves thermal resistance, which helps maintain cutting edge integrity and extends tool life under variable cutting conditions. What is the role of the D10 chipbreaker? The D10 chipbreaker shapes and breaks chips for stable evacuation, lowering the risk of chip entanglement and supporting consistent surface quality in milling operations. Is this insert suitable for automated production? Yes; the combination of the WSP46G grade and D10 chip control provides process stability and repeatable performance that suits automated and high‑volume machining. Can this insert be used for finish as well as roughing passes? The grade’s toughness and the coating’s wear resistance allow for flexible use in both roughing and semi‑finish milling, depending on cutting parameters and toolpath strategy. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only and do not imply any affiliation. The offered article is original and supplied as factory‑new goods of the manufacturer (Walter Tools).
P3204-D12 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of predictable chip control, a coated carbide grade optimised for wide-ranging machining tasks, and standardised ISO designation for straightforward tool selection — all supporting efficient milling cycles. Order directly via Metav Werkzeuge or contact the consultants for application advice. P3204-D12 WHH15X milling indexable insert – D12 chipbreaker, Walter Tools The P3204-D12 WHH15X is a robust milling indexable insert designed for general-purpose face and peripheral milling, combining a D12 chipbreaker with a coated carbide grade for consistent chip formation and tool life. Coated carbide grade WHH15X D12 chipbreaker for controlled chip formation Open series for broad material coverage Stable chip formation for uninterrupted production The primary advantage of the insert is its D12 chipbreaker, engineered to produce short, controlled chips across a variety of milling conditions. Predictable chip geometry reduces the risk of chip accumulation at the cutter, which in turn lowers the likelihood of machine stoppages and improves process reliability. The design contributes to stable cutting forces, enabling consistent component quality and fewer in-process interruptions. Coated carbide grade offers wear resistance and process reliability The WHH15X designation denotes a coated carbide grade selected for balanced wear resistance and versatility. Coatings increase resistance to abrasive and adhesive wear, extending effective tool life under mixed machining regimes. For users less familiar with cutting-material interactions, "coated carbide" means a hard substrate with a thin, engineered layer that reduces friction and heat at the cutting edge, translating into steadier surface finish and reduced tool-change frequency. Material suitability should be checked against the product matrix for optimal results. Clear identification and integration into tool programmes The ISO-style designation P3204-D12 simplifies tooling logistics by matching inserts to compatible holders and tool assemblies via standard codes. The open-series classification signals broad applicability, allowing machining planners to consider the insert where flexibility is required. Because the insert specification in the catalogue is decisive for final selection, consult the manufacturer matrix to confirm compatibility with specific workpiece materials and cutting parameters. This approach supports systematic tooling strategies and predictable production planning. Contact Metav Werkzeuge for tailored application support and precise selection of the Walter Tools P3204-D12 WHH15X milling insert — email info@metav-werkzeuge.com or call +49 2822 7131930 for expert advice and availability Technical data Article number: P3204-D12-WHH15X-WALTER SKU: P3204-D12-WHH15X-WALTER Product type: Fräswendeschneidplatte / milling indexable insert Designation: P3204-D12 WHH15X Chipbreaker: D12 Facts Series: Walter Schneidstoffsorte - Serie offen Grade: WHH15X (coated carbide) Material specification: Katalogabhängig Special features Coated carbide grade WHH15X D12 chipbreaker for controlled chips Open series for broad material coverage Suitability: Check product matrix for material applications FAQ What machining tasks suit this insert best? The P3204-D12 WHH15X insert is intended for general-purpose milling where controlled chip formation and balanced wear resistance are required; check the product matrix for specific material pairings. How does the D12 chipbreaker affect process stability? The D12 chipbreaker promotes short, consistent chips, which improves chip evacuation and lowers the chance of interference with the cutter, enhancing process stability during milling. Is the WHH15X grade suitable for stainless or hardened materials? WHH15X is a coated carbide grade with broad applicability; suitability for particular steels or hardened materials must be confirmed in the product matrix and catalogue data. Can the insert be used across different tool holders? The ISO-style code P3204-D12 supports standardised identification and helps match the insert with compatible holders; confirmation via holder specifications is advised. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools) is among the world’s leading manufacturers of precision metalworking tools and is part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and registered marks are used for clarification only. The offered item is original, factory-new merchandise from the manufacturer; there is no affiliation between our company and the mentioned brands.
P3204-D12 WSM36G WSM36G Wendeplatten - Walter Tools
High process reliability and excellent edge stability make the P3204-D12 WSM36G a dependable choice for demanding machining of stainless steels and heat‑resistant superalloys; combined with the Tiger·tec Gold coating and the D12 chipbreaker, the insert promotes stable chip formation and extended tool life. Order the P3204-D12 WSM36G directly via Metav Werkzeuge or ask our consultants if needed. P3204-D12 WSM36G – Milling indexable insert for stainless steel and superalloys | Walter Tools (Tiger·tec Gold) A P3204-D12 WSM36G milling insert engineered for stable chip control and robust performance when machining rostfreier Stahl and heat‑resistant alloys. Tiger·tec Gold coating technology Optimised D12 chipbreaker for stable chips Designed for rostfreier Stahl and superalloys Coated carbide grade WSM36G Maximise process security with a proven coating system The combination of Tiger·tec Gold and the WSM36G grade delivers measurable gains in process security and repeatability. The coating layer reduces thermal load at the cutting edge, improving wear resistance and enabling longer periods between index changes. In practical terms, this results in fewer interruptions in production and more predictable machining outcomes when working with materials that tend to work‑harden or generate high temperatures. The design supports tight tolerance demands and contributes to a steady machining cadence on high‑mix or high‑volume lines. Consistent chip control for higher productivity The D12 chipbreaker is optimised to promote short, controllable chips when face milling or shoulder milling rostfreier Stahl and similar alloys. A reliable chip geometry reduces the risk of built‑up edge and improves surface finish, which in turn lowers rework rates and cleaning effort. Coated carbide, as used in this grade, combines a hard substrate with a wear‑resistant surface layer to maintain edge stability under thermal and mechanical stress. For workshops seeking efficient material removal without sacrificing component integrity, the insert’s chip control contributes directly to cycle‑time reduction and predictable tool life. Clear application guidance and material compatibility The grade is intended primarily for challenging materials: M (stainless steels) and S (heat‑resistant superalloys and titanium), where thermal stability and secure chip formation are critical. Depending on the cutter geometry, the insert performs well in both roughing and semi‑finishing operations on these groups. The designation indicates suitability rather than the insert material itself; the component is a coated carbide insert designed to handle tough workpiece behaviour. For specific cutting data and recommended geometries, technical consultation is advised to match insert choice with machine capability and workpiece requirements. Request application advice from Metav Werkzeuge for the P3204-D12 WSM36G milling insert – call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: P3204-D12-WSM36G-WALTER Designation: P3204-D12 ISO designation: P3204-D12 WSM36G Grade: WSM36G Series: Tiger·tec Gold Chipbreaker: D12 Manufacturer: Walter Tools Product type: Fräswendeschneidplatte / milling insert Core specifications Material groups: S / M Suitable for: rostfreier Stahl (stainless steel) Coating: Tiger·tec Gold Coated carbide grade: WSM36G Special features Optimised chip control for stable chips Enhanced edge stability and wear resistance Designed for heat‑resistant alloys and titanium (S) Supports secure chip formation in stainless steels (M) Suitable for machining strategies requiring consistent tool life FAQ What materials is this insert suitable for? The P3204-D12 WSM36G insert from Walter Tools is suitable for rostfreier Stahl (stainless steel) and heat‑resistant superalloys (material groups M and S), where thermal stability and chip control are essential. What does the D12 chipbreaker provide? The D12 chipbreaker creates short, controllable chips to reduce built‑up edge and improve surface finish; in the P3204-D12 WSM36G it supports steady chip evacuation and consistent machining results. How does Tiger·tec Gold improve performance? The Tiger·tec Gold coating reduces heat transfer to the cutting edge and increases wear resistance, which improves tool life and process reliability when machining demanding materials. Is this insert suitable for finishing as well as roughing? Yes, depending on cutter geometry and machine setup, the P3204-D12 WSM36G can be used for both roughing and semi‑finishing operations on appropriate materials. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Walter AG (brand: Walter Tools) is a leading manufacturer of precision metalworking tools and forms part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trade designations are mentioned solely for explanatory purposes; there is no connection between our company and the mentioned brands. The offered article is an original, factory‑new product of the manufacturer.
P3204-D12 WSP46G WSP46G Wendeplatten - Walter Tools
Take advantage of the combination of long tool life and secure chip control to boost milling productivity; the Tiger·tec Gold coating and the WSP46G grade deliver versatile performance across steel, stainless steel and heat-resistant superalloys, while Metav Werkzeuge provides application advice and supply options. P3204-D12 WSP46G milling insert — Tiger·tec Gold, for steel, stainless steel and superalloys · Walter Tools The P3204-D12 WSP46G is a coated carbide milling insert by Walter Tools, engineered for versatile face and peripheral milling where reliable chip control and extended edge life are required Tiger·tec Gold PVD coating for improved tool life WSP46G grade for steel, stainless and superalloys D12 chipbreaker for secure chip control Robust coated carbide for stable cutting edge Increase throughput with consistent process stability The combination of the Tiger·tec Gold PVD coating and the WSP46G grade provides measurable gains in productivity through improved wear resistance and predictable flank performance. Coating technology reduces friction and thermal loading at the cutting zone, which extends useful life and reduces frequency of index changes. For production environments this means fewer interruptions and steadier cycle times, supporting a more efficient machining flow without sacrificing component quality. Confident machining across P / M / S material groups Designed for the ISO groups P, M and S, the insert adapts to unalloyed and alloyed steel, stainless steel and heat‑resistant superalloys or titanium. The grade’s toughness helps prevent premature chipping when cutting sticky or work‑hardening stainless steels, while its heat resistance maintains edge stability in nickel‑based alloys. The result is a single, versatile insert choice that reduces tool inventory while covering a broad material spectrum. Better chip control and surface consistency The D12 chipbreaker geometry supports controlled fragmenting and evacuation of chips under typical milling feeds, reducing risk of recutting and improving surface finish. A well‑formed chipbreaker helps maintain consistent cutting forces, lowering vibration and protecting the tool edge. Operators with limited metrology background can consider the chipbreaker as the insert’s built‑in chip management feature that directly supports repeatable surface integrity. Proven construction and manufacturer reliability Manufactured by Walter Tools, the insert is a coated carbide design optimised for milling operations where long tool life and edge stability are priorities. The grade selection emphasises a balance between toughness and wear resistance, helping to reduce downtime related to tool changes. For specialised applications, Metav Werkzeuge can advise on cutting data and suitable toolholders to maximise life and part quality. Contact Metav Werkzeuge for tailored application advice and to request availability of the Walter Tools P3204-D12 WSP46G Tiger·tec Gold milling inserts Technical Data Article number: P3204-D12-WSP46G-WALTER SKU: P3204-D12-WSP46G-WALTER Product type: Milling insert Series: Tiger-tec Gold Grade: WSP46G Chipbreaker: D12 Manufacturer: Walter Tools Internal ID: P3204-D12-WSP46G-WALTER Facts ISO designation: P3204-D12 WSP46G Material groups: P / M / S Coating type: PVD (Tiger·tec Gold) Material construction: coated carbide Special features Versatile WSP46G grade for diverse materials D12 chipbreaker for controlled chips Designed for face and peripheral milling Focus on stable cutting edge and wear resistance FAQ What materials can be machined with this insert? The P3204-D12 WSP46G insert is specified for ISO groups P, M and S, meaning it is suitable for machining steel, stainless steel and heat‑resistant superalloys or titanium. How does the Tiger·tec Gold coating benefit tool life? The Tiger·tec Gold PVD coating on this Walter Tools insert reduces friction and improves thermal resistance, which translates into longer tool life and more stable cutting performance under continuous milling. What is the role of the D12 chipbreaker? The D12 chipbreaker geometry promotes fragmenting and evacuation of chips during milling, improving surface finish and reducing the risk of chip re-cutting that can damage the cutting edge. Is this insert suitable for high‑feed milling operations? The WSP46G grade and D12 chipbreaker are designed for versatile milling; suitability for high‑feed applications depends on specific cutting parameters and workpiece material—use the grade’s toughness and coating properties as indicators of robust performance. Which manufacturer produces the P3204-D12 WSP46G insert? The insert is a Walter Tools product; the P3204-D12 WSP46G benefits from Walter’s Tiger·tec Gold coating technology and expertise in milling applications. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names are used solely for explanation. There is no affiliation between the seller and the mentioned brands. The offered item is an original, factory‑new product of Walter Tools.
P3204-D12.7 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide performance, precise D12.7 chip control and predictable tool life for efficient milling operations; order genuine inserts via Metav Werkzeuge or contact their consultants for application advice. P3204-D12.7 WHH15X milling indexable insert — D12.7 chipbreaker, Walter Tools The P3204-D12.7 WHH15X is a coated carbide milling indexable insert developed for controlled chip formation and stable cutting in general milling tasks; material suitability should be verified using the product matrix. Coated carbide grade WHH15X D12.7 chipbreaker for controlled chips Intended for milling applications Consistent chip control that increases productivity The geometry with a D12.7 chipbreaker offers defined chip segmentation and evacuation, which reduces the risk of built-up edge and frequent interruptions. As a coated carbide grade, WHH15X supports stable cutting under varied conditions and is designed to deliver predictable tool life and repeatable surface quality. These technical properties translate directly into fewer tool changes and more continuous machining time, improving process efficiency in production environments where cycle time and machine utilisation matter. Predictable results through straightforward tool management The open series format enables easy integration into standard toolholders and straightforward indexing, simplifying inventory handling. With its defined insert designation and chipbreak geometry, handling and replacement follow clear procedures that reduce setup complexity and minimise downtime. Material compatibility is catalogue-dependent; therefore, the product matrix should be consulted to confirm suitability for the specific workpiece material and machining strategy. This clarity in application planning supports higher first-pass yields and consistent component quality. Technical support and selection guidance for safe implementation Selection of the correct insert grade and cutting parameters is a decisive factor for process reliability. Walter Tools products benefit from manufacturer know-how and documented cutting data; when the P3204-D12.7 WHH15X is applied in the right context it contributes to stable machining and consistent surface finish. For unfamiliar materials or challenging cutting conditions, professional advice helps to match the insert grade, coating and geometry to productivity targets while safeguarding tool life and component integrity. For tailored recommendations and to order genuine Walter Tools P3204-D12.7 WHH15X milling inserts, contact Metav Werkzeuge for detailed application support: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: P3204-D12.7-WHH15X-WALTER Designation: P3204-D12.7 WHH15X Product type: milling indexable insert Manufacturer: Walter Tools Facts Chipbreaker: D12.7 ISO designation: P3204-D12.7 WHH15X Special features Coated carbide grade WHH15X Series: Walter Schneidstoffsorte - Serie offen Material: catalogue-dependent Application: verify material suitability in product matrix FAQ What is the primary advantage of the D12.7 chipbreaker? The D12.7 chipbreaker provides controlled chip formation and evacuation, which helps the P3204-D12.7 WHH15X insert maintain stable cutting and reduce unplanned interruptions. Which materials can be machined with this insert? Material suitability for the P3204-D12.7 WHH15X is catalogue-dependent; consult the product matrix to determine whether the coated carbide grade WHH15X matches the intended workpiece material. Is this insert suitable for high-speed milling? The coated carbide construction and chipbreaker geometry are designed for productive milling; specific cutting speeds and feeds should be selected according to the machining task and verified against Walter Tools cutting data. How does the open series benefit tool management? An open series format simplifies integration into standard toolholder systems and makes indexing and replacement straightforward, reducing downtime and easing stock management. Where to obtain application support and genuine inserts? Metav Werkzeuge provides technical advice and supply of genuine Walter Tools inserts; contact them for selection help and ordering. The Walter AG (brand presentation: Walter Tools), headquartered in Tübingen, belongs to the group of leading manufacturers of precision tools and is part of the Sandvik group. Protected trademarks and product names are the property of their respective owners. Mention of brand names serves explanation purposes only and does not imply any affiliation between Metav Werkzeuge and the mentioned manufacturers.
P3204-D12.7 WSM36G WSM36G Wendeplatten - Walter Tools
Combining the Tiger·tec Gold coating, the WSM36G grade and the D12.7 chipbreaker delivers robust edge stability and reliable chip control for demanding machining tasks; order the insert directly via Metav Werkzeuge or consult the team for application advice. P3204-D12.7 WSM36G milling indexable insert — Tiger·tec Gold grade for rostfreier Stahl and superalloys | Walter Tools The P3204-D12.7 WSM36G is a milling indexable insert developed for secure cutting-edge performance in the machining of rostfreier Stahl and heat‑resistant superalloys, combining a wear‑resistant coating with a defined chipbreaker geometry. Tiger·tec Gold coating for extended tool life WSM36G grade for rostfreier Stahl and superalloys Stable cutting edge under high temperatures D12.7 chipbreaker for consistent chip control High-temperature stability that protects the cutting edge The combination of a Tiger·tec Gold coating and the WSM36G coated‑carbide grade provides enhanced wear resistance and thermal stability during prolonged contact with hard, adhesive workpiece materials. In practice, this means the insert maintains a sharper, more durable edge when machining rostfreier Stahl and nickel‑based alloys, reducing the frequency of index changes and lowering process interruptions. The coating technology also supports a predictable flank wear pattern, which simplifies tool‑life monitoring and planning in production environments. Reliable chip control for uninterrupted machining The D12.7 chipbreaker geometry is designed to produce controlled chip forms even under challenging cutting conditions. Secure chip control minimises the risk of built‑up edge and erratic chip behaviour that can damage surfaces or compromise cycle times. For batch production or high‑mix operations, the consistent chip evacuation offered by this geometry helps to protect workpiece quality and reduces time spent on machine cleaning and part rework, contributing directly to improved throughput. Productivity gains through process security A coated carbide grade like WSM36G supports higher cutting parameters while keeping tool wear in check, which translates into measurable productivity gains. Stable edge retention and consistent performance on rostfreier Stahl and superalloys enable higher feed rates or longer tool paths between index changes without sacrificing surface finish. The result is a more predictable machining process and improved component repeatability, which is particularly relevant for demanding sectors such as aerospace and medical engineering where material behaviour is critical. Practical application notes and selection guidance The insert is optimised for operations that require a balance of thermal resistance and cutting‑edge stability; it is therefore particularly suitable for milling tasks on rostfreier Stahl and heat‑resistant superalloys. Geometry and grade selection should be matched to the machine capability and workpiece clamping conditions to exploit the Tiger·tec Gold technology fully. For tailored recommendations regarding cutting speeds, feeds and coolant strategies for this Walter Tools insert, Metav Werkzeuge provides technical consultation to support process integration and reduce setup time. Contact Metav Werkzeuge for specific application advice on Walter Tools Tiger·tec Gold inserts such as the P3204-D12.7 WSM36G and to request availability or a technical data sheet via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: P3204-D12.7-WSM36G-WALTER Article name: Fräswendeschneidplatte P3204-D12.7 WSM36G Product type: Fräswendeschneidplatte (milling indexable insert) Brand: Walter Tools Facts Grade: WSM36G Series: Tiger·tec Gold Chipbreaker: D12.7 Material designation: S / M Special features Coating: Tiger·tec Gold (coated carbide) Suitable for: rostfreier Stahl Application scope: Superalloys and rostfreie Stähle Sortenbeschreibung: beschichtetes Hartmetall FAQ Is this insert suitable for machining rostfreier Stahl? The WSM36G grade and Tiger·tec Gold coating make the insert well suited to machining rostfreier Stahl, offering improved edge stability and reduced tendency to build up material on the cutting edge. What workpiece materials are recommended for the insert? The insert is specified for rostfreier Stahl and heat‑resistant superalloys (designation S / M), supporting operations where high thermal load and material adhesion are critical. How does the D12.7 chipbreaker affect machining? The D12.7 chipbreaker produces controlled chip forms that enhance chip evacuation and reduce the risk of built‑up edge, supporting uninterrupted machining and consistent surface quality. Which series and coating does the insert feature? The insert is part of the Tiger·tec Gold series and is a coated carbide type designed to increase thermal resistance and wear performance in demanding applications. Can the insert be used on titanium alloys? While optimised for superalloys and rostfreier Stahl, the listed material designation S indicates suitability for certain heat‑resistant materials; machining titanium requires geometry and parameter adjustments according to the specific titanium grade. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered article is an original, brand‑new product of the manufacturer Walter Tools.
P3204-D12.7 WSP46G WSP46G Wendeplatten - Walter Tools
Combining the Tiger‑tec Gold PVD technology with a D12.7 chipbreaker and a coated carbide substrate delivers dependable chip control and prolonged tool life for milling steel, stainless steel and heat‑resistant alloys. Order directly via Metav Werkzeuge or consult our specialists for application support. P3204-D12.7 WSP46G indexable milling insert – Tiger‑tec Gold, D12.7 chipbreaker (Walter Tools) The P3204-D12.7 WSP46G is an indexable milling insert engineered for versatile milling across steel, stainless steel and high‑temperature alloys, offering robust edge stability and reliable chip formation. Tiger‑tec Gold PVD coating D12.7 chipbreaker for reliable chips Coated carbide for tough milling Suitable for P / M / S materials Consistent cutting performance for demanding milling operations The P3204-D12.7 WSP46G combines a PVD Tiger‑tec Gold finish with a coated carbide body to balance heat resistance and wear protection. This combination supports a stable cutting edge under the high thermal loads typical of steel and stainless steel machining, maintaining geometry over longer tool life cycles. The D12.7 chipbreaker promotes predictable chip formation, reducing interruptions caused by poor chip evacuation and improving cycle time reliability. Improved component quality and reduced rework Thanks to controlled wear behaviour and strong edge stability, the insert helps achieve repeatable surface quality and dimensional consistency on each pass. The coating minimises built‑up edge and flank wear, which in turn lowers scrap rates and secondary finishing. For production environments the result is measurable: fewer rejects, less manual rework and a clearer path to target tolerances with consistent first‑pass quality. Broad material scope with clear application logic This cutting grade is specified for the ISO material groups P / M / S, meaning suitability for unalloyed and alloyed steel (P), stainless steel (M) and heat‑resistant superalloys or titanium (S). The insert’s construction addresses the distinct challenges of each group — chip control and heat management for steel, edge integrity for stainless steel, and thermal stability for superalloys — enabling one grade to service multiple applications in mixed‑material machining cells. Productivity gains through efficient chip control and handling The D12.7 chipbreaker is tailored for consistent chip segmentation and removal in milling passes, supporting higher feed rates while maintaining process security. The indexable design reduces tool change time and simplifies inventory management compared with geometry‑specific solid tools. Combined with the Tiger‑tec Gold technology and the coated carbide substrate, the solution supports steady throughput, lower downtime and predictable replacement intervals that contribute directly to operational efficiency. Contact Metav Werkzeuge today for tailored application advice on Walter Tools Tiger‑tec Gold inserts and to arrange fast delivery or technical consultation via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: P3204-D12.7-WSP46G-WALTER ISO designation: P3204-D12.7 WSP46G Product type: Fräswendeschneidplatte Series: Tiger‑tec Gold Grade: WSP46G Manufacturer: Walter Tools Facts Chipbreaker: D12.7 Material groups: P / M / S SKU: P3204-D12.7-WSP46G-WALTER Special features Coating: Tiger‑tec Gold (PVD) Substrate: coated carbide Suitable for: steel (P), stainless steel (M), superalloys/titanium (S) Application: milling, indexable insert operations FAQ What materials can this insert machine effectively? The P3204‑D12.7 WSP46G is designed for ISO groups P, M and S — meaning steel, stainless steel and heat‑resistant superalloys or titanium — providing tailored wear behaviour and chip control for each group. How does the Tiger‑tec Gold coating benefit milling performance? The Tiger‑tec Gold PVD coating on this Walter Tools insert increases wear resistance and thermal stability, which supports longer tool life and improved surface finish under high cutting temperatures. Is the D12.7 chipbreaker suitable for high‑feed milling? Yes. The D12.7 chipbreaker offers predictable chip segmentation and evacuation, enabling stable feeds and helping to maintain process security during aggressive milling passes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Markennamen und geschützte Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen and registered trademarks are mentioned for explanatory purposes only and do not imply any affiliation between our company and the mentioned brands. The offered item is an original, brand‑new product of the manufacturer.
P3204-D15.87 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide durability and precise chip control for uninterrupted milling cycles; the D15.87 chipbreaker promotes stable chip formation and consistent process security. Order the insert directly via Metav Werkzeuge or request specialist advice from the consultants at Metav Werkzeuge. P3204-D15.87 WHH15X — Indexable milling insert with D15.87 chipbreaker by Walter Tools A P3204-D15.87 WHH15X indexable milling insert designed for reliable chip control in productive milling applications, featuring a coated carbide grade and an open-series Walter Schneidstoffsorte for flexible tool management Coated carbide grade WHH15X D15.87 chipbreaker for stable chips Open-series Walter grade for flexibility Precision geometry for productive milling Improved productivity through controlled chip evacuation The design focusses on chip control as a direct driver of cycle time and tool life. The integrated D15.87 chipbreaker shapes chips to reduce interruptions and prevent recuts, which translates into fewer stoppages and steadier feed rates. For machining centres and production lines where uninterrupted operation is required, this approach reduces secondary handling and improves throughput. The term chipbreaker refers to a specially engineered groove or flank geometry that deliberately fractures chips; this is particularly important in milling where long, stringy chips can compromise surface quality and machine safety. Coated carbide grade for wear resistance and consistency The insert is manufactured in a coated carbide grade identified as WHH15X, a coated hardmetal formulation intended to provide wear resistance and edge stability. Coatings on carbide inserts reduce abrasive and adhesive wear and can improve performance under varying cutting conditions. As the grade is part of an open Walter series, the coating and substrate combination has been selected to offer a balance between edge robustness and re-sharpening potential. Material suitability should be verified against the product matrix to determine the optimal cutting data for specific workpiece materials and machining strategies. Simple integration into modular milling systems The geometry and designation follow established indexable insert standards, enabling easy replacement in common milling holders and cutter bodies. The indexable milling insert concept allows multiple cutting edges per insert to be used by indexing, lowering tooling costs per produced part. Because the insert belongs to an open series, tool planners can combine it with different cutter bodies to adapt to changing production requirements. For qualified preparation, the product matrix provides the recommended cutting data and material pairings; adherence to those guidelines supports predictable tool life and quality outcomes. Contact Metav Werkzeuge today to discuss the Walter Tools P3204-D15.87 WHH15X and obtain tailored recommendations for integrating this coated-carbide indexable insert into the production workflow Technical data Article number: P3204-D15.87-WHH15X-WALTER Designation: P3204-D15.87 WHH15X Type: Indexable milling insert Grade: WHH15X Chipbreaker: D15.87 Series: Walter Schneidstoffsorte - Serie offen Material base: Coated carbide Facts SKU: P3204-D15.87-WHH15X-WALTER Chipbreaker code: D15.87 Special features Coated carbide grade WHH15X Open series for flexible tool combinations Precision chip control for reduced interruptions Product matrix: verify material suitability FAQ What is the primary benefit of the D15.87 chipbreaker? The D15.87 chipbreaker promotes stable chip formation, which reduces recutting and machine stoppages; the feature is implemented on the P3204-D15.87 WHH15X indexable milling insert by Walter Tools. Is the WHH15X grade suitable for all materials? The WHH15X is a coated carbide grade; material suitability depends on the specific product matrix and the intended application, so reference to the manufacturer's matrix is recommended before selection. How is the insert mounted and replaced in cutters? This indexable milling insert conforms to standard insert geometries for quick indexing and replacement in compatible cutter bodies, enabling multiple cutting edges to be used before disposal. Can this insert improve cycle times in series production? Yes, by improving chip control and reducing interruptions, the insert supports more consistent feeds and longer uninterrupted running times, which can raise effective productivity. Where can cutting data and compatibility information be obtained? Cutting data and recommended material pairings are provided in the product matrix; further application-specific advice can be obtained from Metav Werkzeuge or the Walter Tools technical documentation. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between Metav Werkzeuge and the trademark owners. The offered item is an original, factory-new product of the manufacturer Walter Tools.
P3204-D15.87 WSM36G Wendeplatten - Walter Tools
Take advantage of the WSM36G grade and Tiger‑tec Gold coating for extended tool life and stable chip control in demanding materials; order directly via Metav Werkzeuge or consult our specialists for application support. P3204-D15.87 WSM36G — Milling indexable insert (Tiger‑tec Gold) by Walter Tools The P3204-D15.87 WSM36G is a milling indexable insert engineered for heavy-duty machining of rostfreier Stahl and heat-resistant superalloys, offering high thermal stability and controlled chip formation. Tiger‑tec Gold coating for higher wear resistance High thermal stability for heat-resistant alloys Stable chip formation with D15.87 chipbreaker Optimised edge for secure cutting performance Reliable performance in rostfreier Stahl and superalloys The combination of the WSM36G grade and the Tiger‑tec Gold coating delivers high thermal stability and resistance to abrasive wear when machining rostfreier Stahl and nickel‑based superalloys. The substrate is a coated carbide designed to withstand elevated cutting temperatures and the tendency of these materials to produce built‑up edge. As a result, the insert maintains a stable cutting edge for longer, reducing unplanned tool changes and improving process uptime. For production environments where consistent part quality is essential, this insert supports repeatable results and fewer rejects. Precise chip control with the D15.87 chipbreaker The integrated chipbreaker D15.87 ensures stable chip formation, which is crucial when machining ductile or heat‑sensitive alloys. Effective chip control lowers the risk of entanglement, improves coolant access to the cutting zone and contributes to a better surface finish on the workpiece. In practice, this means fewer interruptions for chip clearing and a safer, more predictable machining cycle—qualities that increase throughput and reduce operator intervention in batch and single‑piece workflows. Process security and economical machining Designed for demanding applications, the insert offers process security through a balanced combination of coating technology and substrate toughness. The coated carbide backing ensures resistance to thermal cracking while the coating reduces flank wear. These characteristics translate into longer tool life and a reduced cost per component in medium to high volume production. The insert is compatible with ISO 513 groups M and S, addressing rostfreier Stahl and heat‑resistant superalloys for flexible deployment across mixed‑material production schedules. Integration into productive milling setups With the geometry defined by the designation P3204-D15.87, the insert fits holders and tool systems designed for robust milling operations and can be used where secure clamping and repeatable seating are required. The combination of a proven cutting geometry and an advanced coating system simplifies tool selection and supports stable machinability in challenging applications. For workshops seeking to standardise tooling across similar process families, this insert offers a dependable option that balances cutting performance and predictable maintenance intervals. Contact Metav Werkzeuge for tailored application advice on Walter Tools Tiger‑tec Gold inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: P3204-D15.87-WSM36G-WALTER Designation: P3204-D15.87 WSM36G Type: Milling indexable insert Brand: Walter Tools Grade: WSM36G Series: Tiger‑tec Gold Chipbreaker: D15.87 Material application: S / M Facts ISO material groups: M, S Suitable for: rostfreier Stahl; heat‑resistant superalloys Coating presence: yes Special features Coated carbide grade High thermal stability Stable cutting edge and wear resistance Optimised chip control geometry FAQ What materials is this insert suitable for? This insert is suitable for machining rostfreier Stahl and heat‑resistant superalloys; the WSM36G grade and Tiger‑tec Gold coating provide the required thermal and wear resistance. How does the D15.87 chipbreaker help in production? The chipbreaker D15.87 promotes stable chip formation, improving coolant access and surface finish while reducing the need for manual chip removal during runs. Can the P3204-D15.87 WSM36G be used in high‑temperature cutting? Yes, the Tiger‑tec Gold coating and coated carbide substrate are engineered for elevated cutting temperatures typical when machining superalloys and rostfreier Stahl. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original, factory‑new goods of the manufacturer. Walter Tools is the brand indicated in the product data.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com