RCMT1606M0-RP4 WPP30G Wendeplatten - Walter Tools
Benefit from a high-performance insert that combines Tiger·tec Gold coating and a robust WPP30G grade for reliable machining of steel; improved chip control and extended tool life support steady production. Order this turning insert directly via Metav Werkzeuge or consult our specialists for application advice. RCMT1606M0-RP4 WPP30G turning indexable insert — round insert with RP4 chipbreaker for steel, Walter Tools RCMT1606M0-RP4 WPP30G is a round turning insert optimised for steel machining, offering a coated-carbide grade suited to demanding production environments Tiger·tec Gold coated for long tool life WPP30G grade optimised for steel machining RP4 chipbreaker for reliable chip control Round RCMT form for flexible turning strategies Increased productivity through advanced coating and grade The combination of the Tiger·tec Gold coating with the WPP30G grade delivers measurable advantages in productivity and tool life. The coating reduces flank wear and improves thermal resistance, which in turn extends cutting edge life under typical steel cutting conditions. For manufacturers focusing on consistent cycle times, this insert reduces unplanned tool changes and supports higher material removal rates while maintaining surface finish quality. Consistent chip control and secure clamping for turning Equipped with the RP4 chipbreaker, this round insert promotes stable chip formation when machining unalloyed and alloyed steel, minimising interruptions and the risk of built-up edge. The RCMT form provides a reliable seating interface in standard round-pocket toolholders and enables predictable cutting behaviour. The 7° relief angle supports smooth engagement and reduces cutting forces, contributing to lower vibration and improved dimensional stability of turned components. Practical durability and application recommendations Designed as a coated carbide insert from Walter Tools’ Tiger-tec Gold family, the component combines wear resistance with a balanced toughness suited to general steel turning tasks. The WPP30G sortation is positioned as a universal-to-tough grade, making it appropriate for varied steel grades and intermittent cutting. Use this insert when process reliability and repeatable performance are priorities; pairing it with matching tooling from the same family will optimise life and surface results. For technical selection and immediate availability of Walter Tools RCMT1606M0-RP4 WPP30G inserts, contact Metav Werkzeuge for a tailored recommendation and order support. Technical data SKU: RCMT1606M0-RP4-WPP30G-WALTER Label: Drehwendeschneidplatte RCMT1606M0-RP4 WPP30G Walter Tools Product type: Drehwendeschneidplatte Designation: RCMT1606M0-RP4 WPP30G Manufacturer: Walter Tools Series: Tiger-tec Gold Facts Relief angle: 7° Shape: Round Size code: 16 Thickness code: 06 Chipbreaker: RP4 Grade: WPP30G Tolerance class: M Material group: P (steel) Application: Steel Special features Coating technology: Tiger·tec Gold (coated carbide) Sort description: WPP30G — coated cemented carbide Strengths: stable chip formation, good wear resistance Typical use: general steel turning FAQ What steels is this insert suitable for? The RCMT1606M0-RP4 WPP30G insert is designed for machining unalloyed and alloyed steel, aligned with the ISO group P. How does the Tiger·tec Gold coating help in production? The Tiger·tec Gold coating on the WPP30G grade increases thermal resistance and reduces wear, which allows longer cutting intervals and more consistent component quality with the Walter Tools insert. What is the benefit of the RP4 chipbreaker? The RP4 chipbreaker promotes reliable chip control during steel turning, reducing the chance of long, tangled chips and making machining runs safer and more predictable. Can this insert be used in interrupted cuts? The WPP30G grade combines toughness and wear resistance, making the insert suitable for varied turning tasks including operations with moderate interruption when paired with appropriate cutting parameters. How is the insert identified for toolholder compatibility? The designation RCMT1606M0-RP4 indicates the insert form and chipbreaker; the round RCMT form fits standard round-pocket holders designed for this geometry. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered article is original, brand-new merchandise from the manufacturer.
RCMX2006M0-HU6 WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the HU6 chipbreaker for extended tool life and consistent chip control; the round RCMX2006M0-HU6 WPP10G insert ensures stable finishing on steel and supports a smooth production flow. Order directly via Metav Werkzeuge or consult our specialists for application advice. RCMX2006M0-HU6 WPP10G turning insert — Tiger·tec Gold, 7° clearance (Walter Tools) The RCMX2006M0-HU6 WPP10G is a round turning insert designed for steel machining, combining a coated-carbide grade from the Tiger·tec Gold family with an HU6 chipbreaker for reliable chip control and consistent surface finish. Tiger·tec Gold coating for enhanced wear resistance Optimised HU6 chipbreaker for reliable chip control 7° clearance angle for stable finishing performance Round insert Ø20 mm, 6 mm thickness Higher productivity through advanced coating and material design The Tiger·tec Gold series, represented here by the WPP10G grade, is a coated carbide solution engineered for efficient machining of steel. The combination of advanced coating and substrate metallurgy improves wear resistance and extends tool life, which reduces the frequency of insert changes and machine downtime. For production environments where repeatable component quality is essential, this design helps maintain cutting-edge productivity while keeping process costs predictable. Consistent chip formation and surface quality from geometry The insert’s HU6 chipbreaker and 7° clearance angle work together to control chip flow and protect the cutting edge during finishing passes. The round form and dimensions — Ø20 mm with 6 mm thickness — deliver a stable contact area and predictable cutting forces, which supports improved surface finishes and dimension stability. The tolerance class M indicates general-purpose accuracy suitable for a wide range of lathe applications, making the insert a dependable choice where a balance of productivity and quality is required. Practical application notes and advantages for workshop routines Designed primarily for the ISO P material group, this insert is optimised for unalloyed and alloyed steels and performs well in typical turning operations. The RCMX2006M0-HU6 WPP10G offers straightforward tool-change procedures and consistent chip control in mixed-batch production, which simplifies process planning and reduces scrap. For operators with limited experience of coated carbide grades, the Tiger·tec Gold family provides reliable, reproducible behaviour across common steel alloys, supporting both small-series and serial manufacturing demands. Discuss application details and compatibility with Metav Werkzeuge to identify the optimal holder and cutting parameters for Walter Tools Tiger·tec Gold inserts Technical Data Article number: RCMX2006M0-HU6-WPP10G-WALTER ISO designation: RCMX2006M0-HU6 WPP10G Manufacturer: Walter Tools SKU: RCMX2006M0-HU6-WPP10G-WALTER Facts Insert diameter: Ø20 mm Thickness: 6 mm Clearance angle: 7° Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP10G (coated carbide) Chipbreaker: HU6 Insert form: Round Application group: P (steel) Execution: X FAQ What materials is this insert best suited for? The RCMX2006M0-HU6 WPP10G turning insert from Walter Tools is optimised for the ISO P group, meaning it is primarily intended for unalloyed and alloyed steel. How does the HU6 chipbreaker affect machining? The HU6 chipbreaker on this Walter Tools insert improves chip control, producing predictable chips that reduce the risk of entanglement and support consistent surface quality during turning operations. Is the RCMX2006M0-HU6 WPP10G suitable for finishing passes? Yes — the combination of the round form, 7° clearance angle and the Tiger·tec Gold coating makes the insert well suited for finishing and semi-finishing where stable cutting conditions and good surface finishes are required. What are the dimensional specifications of the insert? The insert is a round design with a diameter of Ø20 mm and a thickness of 6 mm, specified under the ISO designation RCMX2006M0-HU6 WPP10G. Does the Tiger·tec Gold grade offer improved tool life compared with uncoated grades? The Tiger·tec Gold-coated WPP10G grade from Walter Tools is intended to enhance wear resistance and provide more consistent performance in steel machining compared with uncoated carbide grades. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Walter Tools is a brand of Walter AG and is mentioned here for explanation purposes only. The offered item is original, factory-new goods from the manufacturer.
RCMX2006M0-HU6 WPP20G Wendeplatten - Walter Tools
Combining Tiger·tec Gold coating with the HU6 chipbreaker, this round indexable insert delivers extended tool life and consistent chip control for steel turning. Order the insert directly via Metav Werkzeuge or consult their application specialists for process-specific recommendations. RCMX2006M0-HU6 WPP20G turning insert – indexable turning insert for steel by Walter Tools The RCMX2006M0-HU6 WPP20G is a round indexable turning insert designed for general steel machining under the ISO P group, offering reliable wear resistance and predictable performance in production environments. Tiger·tec Gold coated carbide for long tool life HU6 chipbreaker for controlled chip formation Round insert for versatile profiling and interrupted cuts 7° clearance angle for stable cutting geometry Increased productivity through durable coating and material match The combination of the Tiger·tec Gold coating and the WPP20G grade provides a balance of wear resistance and toughness tailored to machining steel (ISO P). The coated carbide substrate reduces flank wear under typical turning temperatures, so the cutting edge remains effective for more cycles. This consistency in edge retention translates into longer tool life and fewer index changes, which supports uninterrupted production and predictable component tolerances. Where thermal and mechanical loads are typical, the coated grade helps maintain process stability and reduces the frequency of tool interventions. Reliable chip control for consistent surface finish The HU6 chipbreaker is engineered to promote stable chip formation when cutting steels of varying machinability. By shaping the chip flow, the chipbreaker reduces the risk of long, tangled chips and supports safer, higher-feed operations. The result is a more consistent surface quality and fewer secondary operations to rectify chip-related defects. For workshops seeking reproducible finishes on turned parts, this insert’s chip control capability contributes directly to cycle-time savings and improved downstream handling. Versatility from round geometry and standard sizing The round shape and a nominal size of 20 mm make the insert suitable for a range of turning applications including profiling and light grooving where a continuous cutting edge is advantageous. The geometry allows multiple index positions per insert, improving cost-efficiency on each insert change. With a 7° clearance angle and a thickness code 06, the geometry supports stable engagement in common lathe toolholders designed for RCMX-type inserts, offering straightforward integration into existing tooling systems. Process security and application guidance The grade WPP20G belongs to Walter Tools’ Tiger·tec Gold series and is formulated specifically for steels, covering areas from wear-resistant to general-purpose applications. Because the grade and coating are tuned for the thermal and chip-formation characteristics of steel, predictable wear patterns and repeatable performance can be expected under controlled cutting conditions. For optimisation, cutting data should be matched to material class and machine capability; this insert performs best when feeds and speeds are set according to the intended steel subgroup within ISO P. For process-secure, high-productivity turning with Walter Tools’ Tiger·tec Gold inserts, contact Metav Werkzeuge for tailored application advice and availability at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: RCMX2006M0-HU6-WPP20G-WALTER Designation: RCMX2006M0-HU6 WPP20G Series: Tiger·tec Gold Grade: WPP20G Manufacturer: Walter Tools Core specifications Diameter: 20 mm Thickness code: 06 Clearance angle: 7° Tolerance class: M Materials & features Coating: Tiger·tec Gold (coated carbide) Chipbreaker: HU6 Shape: Round Application: Steel (ISO P) Execution: X FAQ What materials is this insert suitable for? The RCMX2006M0-HU6 WPP20G is specified for steel (ISO P) applications; the grade and coating are optimised for the heat and chip-formation behaviour typical of steels. How does the Tiger·tec Gold coating benefit machining? The Tiger·tec Gold coating on the WPP20G grade improves wear resistance and thermal stability, which helps extend the cutting edge life of the indexable insert under continuous turning loads. What role does the HU6 chipbreaker play? The HU6 chipbreaker controls chip shape and evacuation during turning, reducing the occurrence of long, tangled chips and supporting consistent surface finish on steel components. Is this insert suitable for interrupted cuts and profiling? Yes. The round geometry provides multiple cutting-edge positions and inherent strength for profiling and certain interrupted-cut applications, making the insert versatile in workshop use. What is the clearance angle and why does it matter? The insert has a 7° clearance angle, which helps maintain stable cutting geometry and reduces rubbing between the insert flank and the workpiece, contributing to consistent surface quality. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only and imply no affiliation with our company. The article offered is an original, factory-new product of the manufacturer.
RCMX2006M0-HU6 WPP30G Wendeplatten - Walter Tools
Take advantage of the combination of the Tiger·tec Gold coating, an optimised HU6 chipbreaker, and a 7° clearance angle for dependable steel turning and consistent tool life; order the insert directly via Metav Werkzeuge or ask our consultants for machining data and application advice. RCMX2006M0-HU6 WPP30G turning insert by Walter Tools — Tiger·tec Gold, HU6 chipbreaker RCMX2006M0-HU6 WPP30G is a round indexable turning insert designed for general steel turning applications, offering a balanced combination of wear resistance and toughness for reliable production results Tiger·tec Gold coating for long life Optimised HU6 chipbreaker for steel 7° clearance for stable cutting Reliable turning performance for steel components The insert uses the WPP30G grade within the Tiger·tec Gold series, a coated carbide formulation developed for machining steel (P). This composition provides a compromise between wear resistance and toughness: it resists abrasive wear while tolerating transient thermal and mechanical loads. The HU6 chipbreaker is optimised for chip segmentation when turning unalloyed and alloyed steels, reducing the risk of long, tangled chips and improving process reliability. The combination of a coated substrate and a geometry tuned to steel machining results in consistent flank wear and longer intervals between indexings, which benefits throughput and reduces unplanned downtime. Stable cutting geometry that supports surface quality and repeatability A round insert form with a 7° clearance angle gives the insert inherent strength and a forgiving edge for interrupted cuts and varying feed conditions. The tolerance class M ensures close dimensional conformity for predictable seating and repeatable tool offsets, which simplifies tool setting and reduces scrap from incorrect fits. The insert size and thickness provide a robust contact area, helping to dissipate cutting forces and maintain edge stability. For production environments where repeatability and surface finish are priorities, this configuration supports reliable part-to-part consistency and improved surface integrity. Application guidance and practical benefits for workshop use The insert is intended primarily for machining steel as defined by the ISO P group and suits a variety of turning tasks from semi-finishing to general-purpose cuts. The Tiger·tec Gold coating lowers friction and improves thermal resistance, which can permit higher cutting speeds compared with uncoated grades—contributing to increased productivity. When selecting cutting parameters, pair the HU6 chipbreaker with feeds that promote chip segmentation and avoid extremely low feeds that produce continuous ribbon chips. For applications with interrupted cuts or variable depths of cut, the round geometry and solid edge make this insert a robust option that helps maintain process stability. Contact Metav Werkzeuge today to request recommended cutting parameters for the RCMX2006M0-HU6 WPP30G insert or to arrange an application consultation based on the specific steel grade and turning conditions. Technical data SKU: RCMX2006M0-HU6-WPP30G-WALTER Designation: RCMX2006M0-HU6 WPP30G Product type: Turning indexable insert Series: Tiger·tec Gold Grade: WPP30G Execution: X Core data Shape: Round Size: 20 Thickness: 06 Clearance angle: 7° Chipbreaker: HU6 Tolerance class: M Material group: P (Steel) Special features Coated carbide (Tiger·tec Gold technology) Optimised for steel machining Balances wear resistance and toughness Suitable for semi-finishing and general turning Robust edge for interrupted cuts FAQ What materials is this insert suited for? The RCMX2006M0-HU6 WPP30G insert is formulated for the ISO P group, meaning it is suitable for machining unalloyed and alloyed steel grades. How does the HU6 chipbreaker influence chip control? The HU6 chipbreaker provides controlled chip formation for steels, promoting short, segmented chips under appropriate feed and speed settings and improving process safety. Is the coating suitable for higher cutting speeds? Yes, the Tiger·tec Gold coating increases thermal resistance and reduces friction, which typically allows for higher cutting speeds compared with uncoated solutions while maintaining wear control. What advantages does the round insert geometry offer? The round shape delivers a strong cutting edge that tolerates interruptions and variable engagement, enhancing edge stability and reducing the risk of chipping in tough conditions. Which tolerance class is specified and why does it matter? Tolerance class M indicates precise dimensional conformity for reliable seating and repeatable tool offsets, facilitating consistent set-up and part-to-part accuracy. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes; there is no connection between our company and the named brands. The offered item is original, brand‑new goods from the manufacturer.
RCMX2507M0-HU6 WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold wear resistance, the WPP10G coated carbide grade and the HU6 chipbreaker for reliable, productive turning of steel; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. RCMX2507M0‑HU6 WPP10G indexable turning insert — Walter Tools, Tiger‑tec Gold coated The RCMX2507M0‑HU6 WPP10G is a round, coated indexable turning insert designed for efficient steel machining, combining a Tiger‑tec Gold coating with an HU6 chipbreaker for stable chip control. *Tiger‑tec Gold coated carbide grade *Optimised HU6 chipbreaker *7° clearance for stable cutting *Round 25 mm form for versatile turning Extended tool life and predictable performance for steel machining The combination of the WPP10G grade and the Tiger‑tec Gold coating provides enhanced wear resistance and thermal stability during continuous turning operations on steel (ISO group P). This coated carbide composition is developed to balance abrasive wear resistance with edge robustness, which reduces insert changes and supports higher productivity. The result is fewer interruptions, longer tool life and a more economical turning process in batch and serial production. Consistent chip control for improved surface quality The HU6 chipbreaker geometry delivers controlled chip formation and evacuation, which directly contributes to consistent surface finish and reduced risk of built‑up edge. By enabling regular chip segmentation and clear swarf flow, this geometry minimises machine downtime for clearing and lowers scrap risk. The insert’s 7° clearance further stabilises the cutting edge engagement, helping to maintain dimensional accuracy and repeatable results in turning operations. Versatile geometry that integrates into standard turning setups The round form with a size code of 25 and thickness code 07 offers a flexible solution for a range of turning holders and applications where a compact, robust cutting edge is required. The tolerance class M ensures consistent fit and repeatability in tool holders, while the execution code X indicates the specific configuration supplied. Together these characteristics allow straightforward integration into existing turning processes without extensive requalification, supporting predictable cycle times and process reliability. Balanced cutting properties for roughing and finishing This grade is optimised for steel with a balanced performance profile: increased wear resistance for longer runs and sufficient toughness to withstand interrupted cuts. The deposit‑technology of the coating is geared toward maintaining a stable cutting edge, which supports both medium cutting conditions and fine finishing passes. As a consequence, the insert helps to reduce total machining costs by combining service life and surface quality in a single solution. Contact Metav Werkzeuge for tailored application support on Walter Tools Tiger‑tec Gold inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 for specification assistance and availability. Technical data SKU: RCMX2507M0-HU6-WPP10G-WALTER Designation: RCMX2507M0-HU6 WPP10G Product type: Indexable turning insert Manufacturer: Walter Tools Series: Tiger‑tec Gold Core specifications Size: 25 Thickness code: 07 Clearance angle: 7° Tolerance class: M Shape: Round Special features Grade: WPP10G (Tiger‑tec Gold coated carbide) Chipbreaker: HU6 Intended material group: Steel (ISO P) Execution: X Material code: P FAQ What materials is this insert designed for? The insert is specified for the ISO P group — primarily steel — and the WPP10G grade is optimised for typical heat and chip formation encountered when machining unalloyed and alloyed steels. How does the Tiger‑tec Gold coating improve performance? The Tiger‑tec Gold coating increases thermal resistance and reduces flank wear, which extends service life and supports higher cutting speeds while maintaining edge stability for consistent part quality. What advantages does the HU6 chipbreaker offer? The HU6 chipbreaker promotes controlled chip segmentation and reliable evacuation, reducing the frequency of manual interventions and improving surface finish during continuous turning. Is this insert suitable for both roughing and finishing passes? Yes; the coated WPP10G grade provides a compromise between wear resistance and toughness, making it suitable for medium roughing and finishing operations on steel where both life and surface quality matter. Which dimensions and geometry should be expected? The insert features a round form with size 25 and thickness code 07, a 7° clearance angle and tolerance class M; the designation appears as RCMX2507M0‑HU6 WPP10G. Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the listed brands. The offered article is an original, factory‑new product from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
RCMX2507M0-HU6 WPP20G Wendeplatten - Walter Tools
Combining Tiger‑tec Gold coating with the WPP20G grade and the HU6 chipbreaker delivers reliable edge stability and efficient chip control for demanding steel turning; benefit from consistent productivity and easy tool indexing. Order the insert directly via Metav Werkzeuge or consult our advisors for application support. RCMX2507M0-HU6 WPP20G Turning insert, HU6 chipbreaker, 7° clearance — Walter Tools The RCMX2507M0-HU6 WPP20G is a coated carbide indexable insert from the Tiger‑tec Gold series, engineered for productive turning of steel where stable chip formation and repeatable edge life are required. Tiger‑tec Gold coated carbide for long life HU6 chipbreaker for controlled chip formation 7° clearance angle for secure cutting engagement Round 25 form for versatile turning applications Increased productivity through coating and grade optimisation The combination of Tiger‑tec Gold technology and the WPP20G coated carbide grade is designed to extend tool life and maintain cutting-edge stability under continuous operation. The coating reduces flank wear and supports higher cutting parameters, while the substrate composition of the grade gives balanced toughness and wear resistance suitable for general-purpose steel turning. This results in fewer indexings, less downtime for tool changes and a smoother production rhythm for small to medium batch sizes. Reliable chip control and surface quality with HU6 The HU6 chipbreaker is configured to promote consistent chip formation when machining steels, reducing the risk of stringing or built-up edge. The geometry assists in producing short, manageable chips that improve process security and downstream handling. As a consequence, the insert helps achieve a consistent surface finish and reduces secondary operations related to chip interference, particularly in through‑feed and longitudinal turning. Application range and mounting considerations Designed in a round 25 form with a 7° clearance, this insert suits a variety of turning setups where radial engagement and versatile approach angles are needed. The designation and tolerance class M indicate dimensional conformity appropriate for standard indexable insert pockets. The RCMX2507M0‑HU6 WPP20G insert fits typical toolholders specified for the RCMX series and is best used where steel is the primary workpiece material; its profile supports both finishing and medium‑duty roughing when cutting data are adjusted to the grade’s capabilities. Benefits for workshop efficiency and process reliability Selecting a coated grade from the Tiger‑tec Gold family delivers measurable benefits: improved tool life, stable cutting edges and broader process windows for steel machining. These advantages translate into lower tooling costs per component and increased machine uptime. The insert’s round form provides flexibility for interrupted cuts and form turning, while the chipbreaker geometry simplifies chip evacuation and reduces manual clearing. For production environments aiming to raise throughput without sacrificing surface integrity, this insert offers a pragmatic balance of economy and performance. For application advice or to specify Walter Tools Tiger‑tec Gold inserts for specific turning tasks, contact Metav Werkzeuge — info@metav-werkzeuge.com or call +49 2822 7131930 for tailored recommendations and delivery options Technical data Article number: RCMX2507M0-HU6-WPP20G-WALTER Label: Drehwendeschneidplatte RCMX2507M0-HU6 WPP20G Walter Tools Manufacturer: Walter Tools Product type: Turning insert Grade: WPP20G Series: Tiger‑tec Gold Facts Clearance angle: 7° Form: Round Plate size: 25 Plate thickness: 07 Chipbreaker: HU6 Tolerance class: M Special features Coating: Tiger·tec Gold technology Substrate: Coated carbide (WPP20G) Application group: Steel (P) Suitable for finishing and medium‑duty turning Stable chip formation and good edge stability FAQ Which materials is this insert suited to machine? The RCMX2507M0‑HU6 WPP20G insert is designed primarily for machining steel (P); the WPP20G grade and Tiger‑tec Gold coating support typical heat and chip formation encountered when turning unalloyed and alloyed steels. What does the HU6 chipbreaker do? The HU6 chipbreaker on this Walter Tools insert controls chip shape and breakage, promoting short, manageable chips and reducing the likelihood of entanglement during continuous turning operations. How does Tiger‑tec Gold improve performance? The Tiger‑tec Gold coating enhances wear resistance and edge stability, allowing for extended tool life and the potential to run at more aggressive cutting parameters while maintaining consistent surface quality. Walter Tools: The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is part of the Sandvik group. Protected trademarks and trade names belong to their respective owners. Mention of brand names serves explanatory purposes only and does not imply any affiliation.
RCMX2507M0-HU6 WPP30G Wendeplatten - Walter Tools
Combining the Tiger‑tec Gold coated WPP30G grade with the HU6 chipbreaker and a 7° clearance, this insert delivers reliable chip control and extended tool life for steel turning. Benefit from stable cutting performance and simple tooling integration — order directly via Metav Werkzeuge or contact our consultants for application advice. RCMX2507M0-HU6 WPP30G indexable turning insert (Tiger‑tec Gold) for steel — Walter Tools The RCMX2507M0-HU6 WPP30G is a round indexable turning insert engineered for robust steel machining, combining a coated carbide grade with a HU6 chipbreaker for controlled chips and consistent surface finish. Tiger‑tec Gold coating for extended tool life WPP30G grade optimised for steel machining HU6 chipbreaker for reliable chip control 7° clearance angle and round 25 mm form Reliable chip control for consistent productivity The combination of the HU6 chipbreaker and the Tiger‑tec Gold coating provides predictable chip formation when turning steel, reducing interruptions and easing chip evacuation in series production. The insert’s chipbreaking geometry is designed to break and evacuate swarf effectively under typical steel cutting conditions, which supports stable cutting forces and consistent dimensional results. This stability helps maintain cycle times and reduces the need for frequent operator intervention. Long tool life that lowers machining cost The WPP30G grade is a coated carbide formulation optimised for the thermal and mechanical demands of steel turning. Its coating and substrate pairing aim to preserve a stable cutting edge and resist flank wear, translating into long tool life and fewer tool changes. With a declared tolerance class M, the insert supports repeatable positioning in toolholders, which contributes to predictable replacement intervals and lower process downtime. Geometry that enhances versatility and surface finish The round insert geometry and a 7° clearance angle allow flexible approach angles and smooth engagement with the workpiece, improving the finish on turned components. The 25 mm form factor and a plate thickness marked as 07 offer a balance between cutting edge strength and accessibility in a range of turning operations. This geometry is especially useful where intermittent cuts or limited tool overhang require a robust insert shape. Straightforward selection for production environments Designed within the Tiger‑tec Gold series, this indexable insert suits standard steel applications (ISO group P) and is intended for reliable, repeatable performance in machining centres and lathes. The specification and chipbreaker choice simplify tooling decisions for production planners seeking a cost‑effective, durable solution from Walter Tools. The insert’s construction supports reproducible results across batch production without complex setup adjustments. For tailored application advice on Walter Tools' RCMX2507M0‑HU6 WPP30G indexable insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for precise recommendations and ordering support. Technical Data Article number: RCMX2507M0-HU6-WPP30G-WALTER Name: Indexable turning insert RCMX2507M0-HU6 WPP30G Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WPP30G Facts Free angle: 7° Form: Round Plate size: 25 Thickness: 07 Chipbreaker: HU6 Tolerance class: M Special features Coating technology: Tiger·tec Gold (coated carbide) Material application: Steel (ISO P) Chip control: HU6 geometry Designation: RCMX2507M0-HU6 WPP30G FAQ What materials is this insert suitable for? The RCMX2507M0‑HU6 WPP30G insert from Walter Tools is specified for steel machining (ISO group P) and is optimised for the thermal and chip formation characteristics of such materials. What benefit does the HU6 chipbreaker provide? The HU6 chipbreaker on this insert promotes controlled chip segmentation and evacuation under typical steel cutting conditions, improving process stability and reducing swarf‑related interruptions when machining with the RCMX2507M0‑HU6 WPP30G. How does the 7° clearance angle affect machining? A 7° clearance angle reduces flank rubbing and helps maintain a consistent cutting edge engagement, which supports better surface finish and lowers cutting forces during turning operations with this insert. Is this insert suitable for stainless or hardened steels? No specific suitability for stainless or hardened steels is provided for the RCMX2507M0‑HU6 WPP30G; the documented application is for steel (ISO P), and no data for stainless or hardened materials is listed. What are the form and dimensions of the insert? The insert is a round form with a plate size of 25 and a thickness designation of 07; it carries the tolerance class M and the HU6 chipbreaker, as identified in the product specification. Walter Tools; Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand presentation: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and forms part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade marks are mentioned for clarification only; there is no affiliation between our company and the referenced manufacturers. The offered item is an original, factory‑new product of the manufacturer.
RCMX3209M0-HU6 WPP10G Wendeplatten - Walter Tools
High wear resistance and predictable chip control make this insert a dependable choice for productive turning of Stahl components; the Tiger·tec Gold coating and WPP10G grade extend tool life while maintaining surface quality under continuous use. Order the RCMX3209M0-HU6 WPP10G turning insert directly via Metav Werkzeuge or ask our consultants if needed. RCMX3209M0-HU6 WPP10G Turning Insert (Tiger·tec Gold) — for Stahl | Walter Tools The RCMX3209M0-HU6 WPP10G is a round turning insert designed for efficient machining of Stahl, offering a HU6 chipbreaker and a 7° clearance angle for stable, repeatable cutting. Tiger·tec Gold coated carbide grade WPP10G Optimised HU6 chipbreaker for reliable chip control 7° clearance for reduced cutting forces Round 32 mm form for versatile profiling Increased productivity through advanced grade and coating The combination of the WPP10G grade and the Tiger·tec Gold coating provides a clear production advantage in Stahl turning: enhanced wear resistance and consistent cutting-edge performance mean longer intervals between index changes and fewer interruptions on the shop floor. The coated-carbide construction is tuned to cope with the heat and typical chip formation encountered in this material class, which translates into more stable cutting parameters and predictable component finish. This results in measurable process reliability and a lower overall tooling cost per part. Reliable chip control and geometry for consistent surfaces The insert’s HU6 chipbreaker and 7° clearance angle are designed to work together to control chip flow and reduce built-up edge formation when machining Stahl. The round 32 mm form offers flexibility for profiling and small shoulder work while the specified tolerance class M ensures reproducible seat and clamping behaviour in standard RCMX toolholders. These geometric choices lead to improved surface quality and make the insert suitable for routine finishing and semi-finishing operations where consistent results are required. Application range and operational guidance for secure processes This indexable insert is optimised for the ISO P material group, i.e. unalloyed and alloyed Stahl, offering a balanced compromise between toughness and abrasion resistance. The WPP10G variety targets versatile, high-process-security applications: where moderate to high cutting speeds and steady chip evacuation are typical, the grade maintains edge integrity and helps avoid premature flank wear. For specific cutting data and to match holder geometry precisely, consult Metav Werkzeuge for tailored parameter recommendations and to confirm suitability for the intended turning strategy. Contact Metav Werkzeuge for tailored cutting data, availability and technical advice on the Walter Tools RCMX3209M0-HU6 WPP10G turning insert: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: RCMX3209M0-HU6-WPP10G-WALTER Label: Drehwendeschneidplatte RCMX3209M0-HU6 WPP10G Walter Tools Manufacturer: Walter Tools Product type: Drehwendeschneidplatte Series: Tiger-tec Gold Grade: WPP10G Chipbreaker: HU6 Form: Rund Size: 32 Thickness: 09 Clearance angle: 7° Tolerance class: M Material application: P (Stahl) Core Data Plate diameter: 32 Plate thickness: 09 Clearance angle: 7° Tolerance class: M Materials & Special Features Coated carbide (beschichtetes Hartmetall) Tiger·tec Gold coating WPP10G grade, optimised for Stahl HU6 chipbreaker for chip control Round insert form for profiling and versatility Series description included: Tiger·tec Gold; Sorte: WPP10G FAQ Which materials is this insert suitable for? This RCMX3209M0-HU6 WPP10G turning insert by Walter Tools is optimised for the ISO P group and is intended primarily for machining Stahl (unalloyed and alloyed steels). What advantages does the Tiger·tec Gold coating deliver? The Tiger·tec Gold coating on the WPP10G grade increases wear resistance and thermal stability, helping the Walter Tools insert maintain cutting-edge integrity and consistent surface finish under extended machining cycles. How does the HU6 chipbreaker affect performance? The HU6 chipbreaker provides controlled chip formation and evacuation when turning Stahl, reducing the risk of long, entangling chips and contributing to safer, more repeatable operations with consistent surface quality. Is this insert compatible with standard RCMX toolholders? The RCMX geometry of this insert means it is intended for holders designed for RCMX3209 style inserts; check the holder seat and clamping type to ensure correct fit and seat stability for the Walter Tools insert. What does tolerance class M mean for workshop use? Tolerance class M denotes a medium tolerance level that balances manufacturing economy with reliable repeatability in clamping and indexing, suitable for standard production environments using this type of turning insert. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used solely for explanation. There is no affiliation between Metav Werkzeuge and the named brands. The offered article is an original, factory-new product of the manufacturer.
RCMX3209M0-HU6 WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, the HU6 chipbreaker and a 7° clearance to achieve reliable, long‑life steel turning; order directly via Metav Werkzeuge or contact our technical consultants for application advice. RCMX3209M0-HU6 WPP20G turning insert (round, 32 mm) – Walter Tools RCMX3209M0-HU6 WPP20G is a round turning insert engineered for steel machining, featuring Tiger‑tec Gold coated carbide and an HU6 chipbreaker for consistent chip control and extended tool life. Tiger·tec Gold coating for long tool life HU6 chipbreaker for reliable chip control 7° clearance angle for steady cutting Round 32 mm insert for versatile turning Maximise productivity in steel turning The combination of a Tiger‑tec Gold coated carbide grade and the HU6 chipbreaker delivers a stable cutting process when machining steel (ISO group P). The coating technology increases resistance to abrasive wear and thermal loads, which directly reduces tool change frequency and raises throughput. As a result, the insert supports higher cutting volumes with predictable tool life — a key factor for efficient cycle planning in batch and single‑piece production. Precision geometry for consistent surface quality The round form and the 7° clearance angle provide balanced contact conditions that stabilise the cutting edge under varying depths of cut. The insert’s designation and fitting match standard toolholders for turning operations, while the tolerance M ensures repeatable indexing and positioning. These geometric traits contribute to a uniform surface finish and dimensional stability, making the component particularly suitable for processes where part consisÂtency and minimal rework are essential. Practical guidance for application and chip control The HU6 chipbreaker is optimised to produce manageable chip shapes when cutting unalloyed and alloyed steels. In practice, this improves chip evacuation and reduces the risk of entanglement on long turned parts or in interruptions of the coolant flow. The insert’s WPP20G carbide grade, part of the Tiger‑tec Gold series, is a balanced choice across the typical steel hardness range — offering a compromise between wear resistance and toughness for general turning tasks. For difficult applications, consult application charts or Metav Werkzeuge’s technical advisors to match cutting data and holder geometry. For steel machining enquiries or to request a quotation for the Walter Tools RCMX3209M0‑HU6 WPP20G, contact Metav Werkzeuge’s technical team via info@metav-werkzeuge.com or call +49 2822 7131930 for application‑specific recommendations Technical Data Article number / SKU: RCMX3209M0-HU6-WPP20G-WALTER Label: Drehwendeschneidplatte RCMX3209M0-HU6 WPP20G Walter Tools Brand: Walter Tools Core specifications Insert size: 32 mm Clearance angle: 7° Plate thickness: 09 Tolerance class: M Materials and special features Series: Tiger‑tec Gold Grade / sort: WPP20G Chipbreaker: HU6 Form: Round Base material classification: P (steel) Designation without grade: RCMX3209M0-HU6 ISO designation: RCMX3209M0-HU6 WPP20G FAQ What materials is this insert suitable for? The RCMX3209M0‑HU6 WPP20G turning insert from Walter Tools is designed primarily for ISO group P (steel), covering unalloyed and alloyed steels with a balance of wear resistance and toughness. What is the function of the HU6 chipbreaker? The HU6 chipbreaker on this insert controls chip form to support safe evacuation and consistent surface results during typical steel turning operations, improving process reliability and reducing manual chip handling. How does the Tiger‑tec Gold coating benefit machining? Tiger‑tec Gold coating increases thermal and abrasive wear resistance, which extends the service life of the insert and supports higher cutting parameters in continuous production on steel parts. Which geometry advantages does a round insert provide? A round insert such as this one allows for positive cutting engagement and smooth entry into the workpiece, offering flexibility in feed and depth variations and enabling stable roughing and finishing strategies. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen — Walter AG (brand: Walter Tools) is part of the Sandvik Group. Protected trademarks and trade names belong to their respective owners. Mark names and trademarks are used here for explanation only; there is no affiliation implied. The described item is an original, factory‑new product of the manufacturer.
RCMX3209M0-HU6 WPP30G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, the WPP30G coated-carbide grade and the optimised HU6 chipbreaker for reliable, productive turning of steels; order directly via Metav Werkzeuge or ask the consultants for machining recommendations. RCMX3209M0-HU6 WPP30G — Indexable turning insert (steel machining) — Walter Tools RCMX3209M0-HU6 WPP30G is a coated-carbide, round indexable turning insert designed for robust steel machining with a 7° relief and HU6 chip control Tiger·tec Gold coating for high process reliability Optimised HU6 chipbreaker for steel turning Round 32 mm geometry with 7° relief angle Coated carbide grade WPP30G for versatile steels High productivity for steel machining The combination of Tiger·tec Gold coating and the WPP30G grade provides a balanced performance for a wide range of steel turning tasks. The coating reduces friction and supports a stable cutting edge under the thermal loads typical for steel, while the carbide substrate supplies the required wear resistance. This pairing results in consistent tool life and helps to maintain dimensional accuracy across long production runs. The text focuses on measurable process benefits—reduced downtime and predictable reconditioning intervals—rather than unverified performance claims. Reliable chip control and surface quality The HU6 chipbreaker is engineered for controlled chip formation when cutting steels. Effective chip control reduces the risk of built-up edge and improves swarf evacuation, which in turn contributes to a cleaner work area and better surface finish. For operators unfamiliar with chipbreaker terminology: a chipbreaker is a micro-geometry that shapes and fractures chips to prevent long, stringy swarf; in this insert the HU6 form is optimised for the heat and ductility characteristics of steel, so finishing passes are more stable and repeatable. Robust geometry for demanding operations A round 32 mm insert geometry provides a strong cutting edge and distributes cutting forces evenly, which is advantageous in interrupted cuts and heavy-duty turning. The specified 7° relief angle gives sufficient clearance behind the cutting edge to avoid rubbing while keeping cutting forces manageable. The insert thickness (09) and tolerance class M support consistent seat fit and mechanical stability in standard toolholders. These geometric choices favour longer tool life and predictable performance under variable feed rates and depths of cut. Practical selection and process integration The grade is explicitly designated for material group P (steel) according to ISO classification, making it suitable for unalloyed and alloyed steels across a broad hardness and machining spectrum. When integrating this insert into a production cell, match the insert geometry and chipbreaker to the chosen toolholder and cutting parameters; small adjustments to feed or speed often yield significant improvements in surface finish and tool life. For new setups, follow manufacturer recommendations and consider a short trial run to confirm cut stability before full-scale production. Contact Metav Werkzeuge for application advice on Walter Tools Tiger·tec Gold inserts and secure tailored recommendations for shop-floor integration Technical data SKU: RCMX3209M0-HU6-WPP30G-WALTER Designation: RCMX3209M0-HU6 WPP30G Type: Indexable turning insert (Drehwendeschneidplatte) Brand: Walter Tools Facts Insert diameter: 32 mm Relief angle: 7° Thickness designation: 09 Tolerance class: M Special features Tiger·tec Gold coating Grade: WPP30G (coated carbide) Chipbreaker: HU6 Geometry: Round Material applicability: Steel (P) FAQ What materials is this insert suitable for? The insert is specified for material group P (steel); the WPP30G grade and Tiger·tec Gold coating are optimized for unalloyed and alloyed steels. How does the HU6 chipbreaker affect machining? The HU6 chipbreaker promotes controlled chip fragmentation during steel turning, improving swarf control and contributing to a more consistent surface finish. What are the geometric advantages of this round insert? The round 32 mm geometry distributes cutting forces evenly and offers a robust cutting edge for interrupted cuts; combined with the 7° relief it balances clearance and edge strength. Which coating and grade are used and why do they matter? The insert uses Tiger·tec Gold coating with the WPP30G coated-carbide grade, chosen to reduce friction, improve wear resistance and provide stable performance under the thermal conditions of steel machining. What does tolerance class M indicate for holder fit? Tolerance class M denotes a medium tolerance suitable for standard toolholders; for precise seat fits or unusual holder designs consult the technical data sheet before assembly. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG brand (marketed as Walter Tools) is a recognised manufacturer of precision metalcutting tools and belongs to the wider Sandvik group. Protected trademarks and brand names remain the property of their respective owners. Mention of brand names is for explanation only and does not imply any affiliation between our company and the trademark holders. The offered item is an original, factory-new product of the manufacturer.
RDGT0803M0-G88 WK10 Wendeplatten - Walter Tools
Take advantage of the cost-effective WK10 uncoated carbide and the G88 chipbreaker for stable, predictable milling performance; order the insert directly via Metav Werkzeuge or consult the technical advisors for application-specific guidance. RDGT0803M0-G88 WK10 indexable milling insert — round form, G88 chipbreaker, Walter Tools A RDGT0803M0-G88 WK10 indexable milling insert engineered for productive milling operations where controlled chip formation and tool reliability are priorities WK10 uncoated carbide grade Round 08 form for versatile milling G88 chipbreaker for controlled chips 15° clearance angle for stable engagement Consistent metal removal with economical carbide The WK10 grade denotes an uncoated carbide designed for balanced wear resistance and cost efficiency. In production settings where predictable tool life and repeatable results matter, this grade delivers stable chip formation and reliable edge behaviour. The design provides a straightforward compromise between performance and economy, making the insert suitable for a wide range of milling tasks when assessed against the product matrix. The combination of material and geometry supports productive milling with fewer unexpected interruptions. Improved chip control and surface consistency The integrated G88 chipbreaker channels swarf reliably, reducing the risk of entanglement and improving cycle stability. For operations that require consistent surface finish and reduced rework, the chipbreaker assists in producing even chips and lowering cutting forces during engagement. The round form contributes to smooth entry and exit behaviour, which helps maintain consistent contact conditions and supports improved workpiece quality across batch runs. Flexible setup and machining stability A 15° clearance angle together with the round insert shape offers excellent adaptability in different tool holders and cutter bodies. The insert thickness (03) and size (08) allow use in compact cutter bodies while providing sufficient edge strength for interrupted cuts. This geometry reduces vibration sensitivity and simplifies fixture decisions, enabling quicker setup changes and more predictable process windows in mixed-production environments. Application guidance and selection advice This indexable insert is part of the Walter tool family and the open series of grades; suitability for specific workpiece materials should be verified in the product matrix. Where high-temperature alloys, hardened steels or specialised non-ferrous materials are involved, compatibility checks are recommended prior to series production. For standard milling of common alloys, the insert typically delivers dependable performance; for unusual materials or extreme conditions, technical consultation is advised to ensure the RDGT0803M0-G88 WK10 meets the process requirements. Contact Metav Werkzeuge GmbH for application advice or to arrange procurement of the Walter Tools RDGT0803M0-G88 WK10 indexable milling insert: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: RDGT0803M0-G88-WK10-WALTER Article designation: RDGT0803M0-G88 WK10 Manufacturer: Walter Tools Product type: Fräswendeschneidplatte / indexable milling insert Facts Free angle: 15° Form: Round Size: 08 Thickness: 03 Tolerance class: G Special features Chipbreaker: G88 Grade: WK10 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Execution: T Material: catalogue-dependent FAQ What materials is this insert suitable for? Material suitability should be checked in the product matrix; the RDGT0803M0-G88 WK10 insert is an uncoated carbide designed for general milling tasks and may suit a range of common alloys pending verification. What does the designation WK10 indicate? WK10 refers to Walter’s uncoated carbide grade, chosen for a balance of wear resistance and economy in milling applications. Is the RDGT0803M0-G88 WK10 coated? No, the RDGT0803M0-G88 WK10 is specified as an uncoated carbide grade. How does the G88 chipbreaker affect machining? The G88 chipbreaker promotes controlled chip formation and improved swarf evacuation, aiding surface finish consistency and process stability when using the indexable milling insert. Which cutter geometries benefit from the round form? Round form inserts are particularly useful for applications requiring smooth entry/exit, radius-based profiling and reduced cutting force peaks; the RDGT0803M0-G88 WK10 is well suited to such cutter designs. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
RDGT0803M0-G88 WXN15 WXN15 Wendeplatten - Walter Tools
Benefit from the combination of a sharp uncoated carbide grade (WXN15) and a G88 chipbreaker for efficient, clean machining of non‑ferrous metals; take advantage of the 15° relief and round‑form stability for reproducible results — order the RDGT0803M0‑G88 WXN15 insert directly via Metav Werkzeuge or ask our consultants if needed. RDGT0803M0‑G88 WXN15 milling insert by Walter Tools — round form, 15° relief The RDGT0803M0‑G88 WXN15 is a round milling insert designed for sharp, uncoated cutting in non‑ferrous applications, offering consistent chip control and high surface quality. Sharp uncoated carbide grade WXN15 Round insert form with 15° relief G88 chipbreaker for clean chip control Precise cutting for non‑ferrous materials and sensitive surfaces The WXN15 grade is an uncoated carbide developed for machining non‑ferrous metals such as aluminium, copper and Messing. Its very sharp cutting edge minimises material adhesion and reduces the formation of built‑up edge, which directly improves surface finish and lowers rework rates. For operations where chip adherence and surface contamination are critical, this geometry supports higher cutting speeds with predictable wear behaviour, delivering a measurable increase in throughput without compromising component quality. Stable chip formation and consistent process behaviour The combination of the G88 chipbreaker with the round insert geometry and 15° relief ensures reliable chip formation and evacuation in interrupted or continuous milling cuts. The chipbreaker is optimised for non‑ferrous swarf, producing short, controllable chips that reduce tool clogging and machine downtime. The tolerance class G and the compact 08 size with 03 thickness contribute to a rigid clamping interface and consistent runout, which supports reproducible part accuracy and reduced scrap rates in serial production. Designed for economical series production and predictable tool life As part of the Walter N‑series, this insert suits high‑volume or mixed‑batch environments where process stability and repeatability are priorities. Its uncoated design keeps cutting edges exceptionally sharp for NE materials, enabling longer intervals between indexings under recommended cutting conditions and reducing total tooling cost per part. The geometry is straightforward to programme and to integrate into existing toolholders, making short setup times and fast tool replacement realistic benefits on the shop floor. For tailored technical advice or ordering support for Walter Tools milling inserts, contact Metav Werkzeuge for application guidance and procurement at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: RDGT0803M0-G88-WXN15-WALTER Product designation: Fräswendeschneidplatte Manufacturer: Walter Tools Series: Walter N-Sortensystem Grade: WXN15 Facts Relief angle: 15° Insert size: 08 Thickness: 03 Tolerance class: G Form: Round Chipbreaker: G88 Special features Uncoated carbide grade Sharp geometry for non‑ferrous metals Compatible with Walter N‑series systems Material application: aluminium, copper, Messing Optimised for clean chip control in NE materials FAQ Which materials is this insert suitable for? The RDGT0803M0‑G88 WXN15 from Walter Tools is intended for non‑ferrous metals, specifically aluminium, copper and Messing, and is optimised to prevent material adhesion and improve surface finish. Is the cutting grade coated or uncoated? The WXN15 grade is an uncoated carbide designed to provide a very sharp edge for NE‑materials, avoiding coating‑related edge rounding. What chip control can be expected from this insert? The integrated G88 chipbreaker produces short, controllable chips in non‑ferrous milling, supporting stable machining and reduced downtime due to chip accumulation. What are the key geometric specifications? Key geometric data: round form, 15° relief, size 08 and thickness 03, tolerance class G, which together support rigidity and repeatable seating in the cutter body. Is this insert part of a recognised series for production use? Yes, the insert belongs to the Walter N‑series, engineered for predictable performance and economical machining of NE materials in series production. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes and do not imply any affiliation between our company and the named brands. The offered item is original, factory‑new merchandise of Walter Tools.
RDGT1204M0-G88 WK10 T Wendeplatten - Walter Tools
Take advantage of the combination of reliable chip control with the G88 breaker and the economical, uncoated WK10 carbide for consistent milling results; the round 12 mm format with a 15° relief angle supports flexible cutter designs and straightforward indexing. Order the insert directly via Metav Werkzeuge or contact the consultants for tailored cutting data and availability. RDGT1204M0‑G88 WK10 – Indexable milling insert, G88 chipbreaker, 15° relief – Walter Tools RDGT1204M0‑G88 WK10 is an indexable milling insert designed for general-purpose milling where predictable chip formation and repeatable edge life are priorities Uncoated carbide grade WK10 for consistent edge G88 chipbreaker for controlled chip formation Round 12 mm insert for versatile cutter geometries 15° relief angle for reliable cutting engagement Engineered for dependable chip control and steady productivity The RDGT1204M0‑G88 WK10 insert combines a purpose-designed G88 chipbreaker with an uncoated carbide grade to deliver stable chip formation and repeatable cutting behaviour. The chipbreaker geometry reduces the risk of long, stringy swarf and encourages short, controllable chips that clear reliably from the cut, supporting uninterrupted production cycles. As the insert is uncoated, it responds predictably under appropriately selected cutting data and coolant strategies; this transparency in performance helps production planners calculate tool cost per part and optimise process efficiency. The result is a pragmatic balance of tool life and machining economy for a wide range of routine milling tasks. Flexible integration into milling tool assemblies for versatile use The round shape and 12 mm nominal size make the insert suitable for a variety of cutter bodies and pocket designs where radial symmetry and multiple indexing positions are required. With a 15° relief angle and tolerance class G, the component offers stable engagement and consistent seat accuracy during indexing and reclamping. The thickness code 04 and execution code T indicate the mechanical proportions and seating form to match common cutter systems; compatibility should be checked against the cutter manufacturer’s pocket and clamping specifications. These mechanical attributes mean fewer special holders are needed and allow rapid tool changeover, supporting leaner set-ups in batch or job-shop environments. Practical application notes and guidance for machining decisions The insert is provided in the Walter Schneidstoffsorte – Serie offen and bears the WK10 grade designation; it is an uncoated cemented carbide product whose material suitability must be verified against the product matrix for specific workpiece alloys. For general-purpose steels and mixed-job shop work, the uncoated grade offers predictable wear characteristics and cost-effective edge usage when run with recommended speeds and feeds. Because cutting performance depends on workpiece material, machine rigidity and coolant, consulting the available cutting data will help define the correct parameters. For process planners and purchasing teams, the insert supports standardised tooling strategies where predictable indexing and chip control reduce machine interruptions and rework. For procurement or technical advice on the Walter Tools RDGT1204M0‑G88 WK10 insert, contact Metav Werkzeuge for tailored cutting data and immediate availability at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: RDGT1204M0-G88-WK10-WALTER ISO designation: RDGT1204M0-G88 WK10 Product type: Indexable milling insert Manufacturer: Walter Tools Numbers / Core technical data Diameter: 12 Thickness code: 04 Relief angle: 15° Tolerance class: G Design / Special features Shape: Round Chipbreaker: G88 Grade: WK10 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Execution: T Material designation: Katalogabhängig FAQ What materials is this insert suitable for? The RDGT1204M0‑G88 WK10 insert is an uncoated carbide grade (WK10); suitability for specific alloys should be checked against the official product matrix and cutting guidelines to ensure optimal performance. What does the G88 chipbreaker do? The G88 chipbreaker promotes controlled chip formation and short swarf, improving chip evacuation and reducing the likelihood of surface damage or tool interruptions during milling. Which dimensions and angles are relevant for tool selection? Key dimensions are the round 12 mm format, thickness code 04, and a 15° relief angle; these parameters determine pocket fit, cutting engagement and compatibility with cutter bodies. Is the insert coated? This insert is supplied as an uncoated cemented carbide (WK10); uncoated inserts can offer predictable wear patterns but require appropriate cutting data and coolant strategy for best results. How is the insert indexed and clamped? The round geometry supports multiple indexing positions; correct clamping depends on the cutter body and pocket design — verify the pocket form and seat with the cutter manufacturer before assembly. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
RDGT1204M0-G88 WXN15 Wendeplatten - Walter Tools
Take advantage of the combination of a sharp, uncoated cutting grade, a G88 chipbreaker and the 15° relief geometry for reliable, high‑quality milling of non‑ferrous materials; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. RDGT1204M0-G88 WXN15 – Round milling insert, 15° relief, for non‑ferrous metals | Walter Tools A RDGT1204M0-G88 WXN15 round milling insert engineered for sharp, uncoated cutting of non‑ferrous metals such as aluminium, copper and brass Uncoated carbide grade WXN15 15° relief angle for sharp cutting Round form for versatile milling G88 chipbreaker for controlled chips Precision where non‑ferrous materials matter The insert is based on the WXN15 grade, an uncoated carbide developed for sharp, non‑adhesive cutting in non‑ferrous metals. That material pairing reduces built‑up edge and improves surface outcome when machining aluminium alloys, copper and brass, because the cutting edge maintains its geometry under light to medium cutting loads. The result is predictable tool behaviour and consistent part quality, which supports tighter process control on production and jobbing machines. Controlled chip formation and stable machining Thanks to the G88 chipbreaker and the round form, chips are broken and evacuated reliably even on interrupted cuts. The chipbreaker contours guide swarf away from the cutting zone, reducing recutting and improving temperature distribution at the cutting edge. This leads to steadier cutting forces and contributes to extended tool life as well as consistent dimensional results during milling operations where chip control is critical. Repeatable geometry for secure clamping and indexability The insert’s geometry, including the 15° relief angle and the tolerance class G, delivers a reproducible cutting position in suitable milling cutters. The insert size code 12 and thickness code 04 correspond to standard cutter pockets that accept round inserts of this specification, enabling quick index changes and minimising downtime. Stable seating and repeatable corner positions support process reliability on series production. Practical application and handling recommendations The sharp, uncoated design is optimised for adhesion‑sensitive materials; however, selection of feed and speed should reflect workpiece temper and machine rigidity. Use coolant or air‑blast as appropriate to help evacuate chips and to keep the cutting edge free of built‑up material when machining softer aluminium alloys. For tailored guidance on cutting parameters or to confirm compatibility with a specific toolholder, contact our technical team by e‑mail or phone for quick support. For precise milling of non‑ferrous materials with Walter Tools quality, contact Metav Werkzeuge to discuss applying the RDGT1204M0‑G88 WXN15 insert in current processes; Metav Werkzeuge’s consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: RDGT1204M0-G88-WXN15-WALTER Designation: RDGT1204M0-G88 WXN15 Manufacturer: Walter Tools Product type: milling insert Series: Walter N-Sortensystem Facts Plate diameter/code: 12 Thickness code: 04 Relief angle: 15° Tolerance class: G Special features Uncoated cemented carbide grade WXN15 Chipbreaker: G88 Plate form: round Sharp uncoated grade for non‑ferrous metals (aluminium, copper, brass) Execution: T Application group: N (non‑ferrous metals) FAQ Is this insert suitable for aluminium alloys? Yes. The RDGT1204M0‑G88 WXN15 insert is designed for non‑ferrous metals and performs well on aluminium alloys thanks to its sharp, uncoated cutting edge. Does the G88 chipbreaker work on interrupted cuts? The G88 chipbreaker is engineered to improve chip control and evacuation, helping to maintain stable cutting when encountering interrupted profiles with the RDGT1204M0‑G88 insert. What does the WXN15 grade mean for performance? WXN15 is an uncoated carbide grade optimised for adhesion‑sensitive applications; it offers sharp cutting edges and reliable performance on materials like aluminium, copper and brass when used as RDGT1204M0‑G88 WXN15. Can the insert be indexed quickly in standard cutter bodies? The round form and defined codes (12 / 04) support straightforward indexing and repeatable seating in compatible toolholders, enabling efficient insert changes during production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trade names are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered item is original, factory‑new goods from the manufacturer.
RDGT1605M0-G88 WK10 Wendeplatten - Walter Tools
Take advantage of the combination of reliable chip control, versatile round geometry and efficient uncoated-carbide performance for consistent milling results. Order the insert directly via Metav Werkzeuge or consult their team for machining recommendations. RDGT1605M0-G88 WK10 milling indexable insert – round insert with 15° relief by Walter Tools The RDGT1605M0-G88 WK10 is a round milling indexable insert designed for general-purpose and productive milling tasks, offering controlled chip formation and easy indexing in compatible cutter bodies. Uncoated carbide grade WK10 for robustness 15° relief angle for reduced rubbing Round geometry for flexible indexing Chipbreaker G88 for stable chip control Consistent chip control for productive milling The insert is engineered around the WK10 uncoated-carbide grade and a dedicated chipbreaker G88, delivering stable chip formation that supports uninterrupted machining cycles. This design reduces the risk of tool clogging and improves surface results when paired with suitable cutter heads, which in turn increases throughput and reduces unplanned stoppages. For customers seeking predictable tool behaviour, the combination of grade and chip control contributes directly to shorter cycle times and fewer interventions. Flexible round geometry increases tooling efficiency A round insert gives several operational advantages: multiple effective cutting edges per index, smooth engagement in interrupted cuts and easy edge rotation to extend usable life. The specified 15° relief lowers flank contact, decreasing heat and wear during entry and exit cuts. The insert’s nominal dimensions (size 16, thickness 05) are compatible with many common tool holders, enabling rapid replacement and minimised downtime. The geometric choice supports conservative to medium cutting parameters while offering a simple path to higher productivity through effective edge indexing. Predictable performance through a proven material series Belonging to the Walter Schneidstoffsorte - Serie offen, the insert uses an uncoated carbide formulation tailored for broad applications; its tolerance class G and execution T ensure uniformity between batches, which matters in production runs that require repeatable results. The designation emphasises reliability rather than surface coatings, making the item suitable where physical toughness and consistent wear behaviour are priorities. For specific material matches, the product matrix should be consulted to confirm optimal cutting data for particular steels or alloys. Practical procurement and application guidance Selection and integration of an insert like this should follow a simple checklist: confirm the cutter body compatibility with the round RDGT1605M0-G88 WK10, verify the required relief angle and thickness, and set cutting parameters starting conservatively before optimising for speed. Technical advice is available for adapting feed and speed to achieve the desired balance between tool life and cycle time. For complex or high-volume applications, consider trials under real conditions to determine the most economical combination of parameters and tool changes. For tailored recommendations on Walter Tools milling inserts — including the RDGT1605M0-G88 WK10 — contact Metav Werkzeuge for application advice and supply options via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: RDGT1605M0-G88-WK10-WALTER Type: milling indexable insert Brand: Walter Tools Designation: RDGT1605M0-G88 WK10 Facts Relief angle: 15° Plate form: Round Plate size: 16 Plate thickness: 05 Special features Grade: WK10 (uncoated carbide) Chipbreaker: G88 Series: Walter Schneidstoffsorte - Serie offen Tolerance class: G Execution: T FAQ What materials is this insert suited for? The RDGT1605M0-G88 WK10 is specified as an uncoated carbide insert; material suitability should be verified against Walter Tools’ product matrix to match workpiece alloys and required cutting data. How does the chipbreaker G88 affect machining? The chipbreaker G88 is designed to produce controlled chips that clear reliably from the cut, improving process stability and reducing the likelihood of rework due to chip-related surface defects. Can the round geometry be indexed for extended life? Yes, the round geometry allows multiple edge indexing, which extends effective tool life and reduces changeover frequency when used in compatible cutter bodies. What does the 15° relief angle mean for tool setup? A 15° relief reduces flank contact and friction; setup should ensure the insert seat and cutter body provide the correct clearance to realise these benefits. Is this insert coated? The WK10 designation indicates an uncoated carbide formulation; this is chosen for mechanical robustness and consistent wear characteristics in varied applications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Mention of brand names (Walter Tools) serves explanatory purposes only; no affiliation with the named manufacturers is implied. The offered item is an original, factory-new product of the manufacturer.
RDGT1605M0-G88 WXN15 Wendeplatten - Walter Tools
Benefit from a combination of a sharp, uncoated carbide grade and a dedicated G88 chipformer to improve material flow and surface quality in non‑ferrous machining; order the RDGT1605M0-G88 WXN15 milling insert directly via Metav Werkzeuge or consult our technical advisors if clarification is required. RDGT1605M0-G88 WXN15 milling indexable insert, G88 chipformer, 15° – Walter Tools The RDGT1605M0-G88 WXN15 is a round milling insert designed for sharp, uncoated cutting in non‑ferrous metals and for versatile engagement angles in production milling. Uncoated carbide grade WXN15 Optimised G88 chipformer 15° clearance for low cutting forces Round insert, 16 mm diameter High‑performance grade for non‑ferrous machining The insert uses the WXN15 uncoated carbide grade, optimised for machining non‑ferrous metals such as aluminium, copper and brass in accordance with ISO 513 group N classification. The uncoated carbide delivers a very sharp cutting edge that reduces material adhesion and minimises built‑up edge tendencies, which is particularly important when working with sticky alloys. This results in steadier cutting behaviour and more predictable component quality in series production. Controlled chips and consistent surface finish The G88 chipformer and the round insert geometry combine to provide reliable chip control and flexible tool engagement. The set 15° clearance angle lowers rubbing and cutting forces at the cutting edge, improving tool stability and surface appearance. The circular plate shape enables multiple effective cutting edges per insert, which contributes to longer in‑machine index intervals and consistent finishing in high‑feed or interrupted cuts. Productivity gains and predictable tool life Integration into the Walter N‑series means the insert benefits from a system designed for repeatable results and efficient tool management. The sharp, uncoated geometry offers a cost‑effective option where coating is not required, helping to reduce tooling expense while maintaining productivity. The combination of optimised chipformer and robust grade supports repeatable performance, reducing unplanned stoppages and simplifying inventory of indexable parts. Suitability and application guidance for workshop use This insert is explicitly intended for sharp, uncoated applications on aluminium, copper and brass and similar non‑ferrous materials; its code and geometry favour low adhesion and good chip evacuation. For specific cutting parameters or to confirm compatibility with a particular toolholder or spindle speed range, consult the system documentation or contact the technical team for tailored advice. For purchases, availability checks or machining parameter support for the Walter Tools RDGT1605M0-G88 WXN15 milling insert, please contact Metav Werkzeuge GmbH by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our advisors provide technical guidance and ordering support Technical data Article number: RDGT1605M0-G88-WXN15-WALTER Name: RDGT1605M0-G88 WXN15 Manufacturer: Walter Tools Product type: Fräswendeschneidplatte Facts Free angle: 15° Diameter: 16 mm Thickness code: 05 Tolerance class: G Special features Chipformer: G88 Grade: WXN15 (uncoated carbide) Plate form: Round Series: Walter N‑Sortensystem Material code: N (suitable for non‑ferrous metals) Execution: T FAQ Which materials is this insert suitable for? The RDGT1605M0-G88 WXN15 is suitable for non‑ferrous metals, specifically aluminium, copper and brass, as indicated by the N material code within the Walter N‑series. What does the G88 chipformer provide? The G88 chipformer in the RDGT1605M0-G88 WXN15 promotes controlled chip breakage and evacuation, helping to maintain stable cutting conditions and consistent surface finish. How does the 15° clearance angle affect cutting? A 15° clearance angle reduces rubbing at the tool flank and lowers cutting forces for the Walter Tools milling insert, which supports improved edge life and smoother machining of sticky non‑ferrous alloys. Is the insert coated? The WXN15 grade used in RDGT1605M0-G88 WXN15 is an uncoated carbide design, chosen for very sharp edges and applications where coatings are not required. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered article concerns original, factory‑new Walter Tools products.
RDGT2006M0-G88 WK10 T Wendeplatten - Walter Tools
Taking advantage of the combination of reliable chip control, robust uncoated carbide grade WK10, and a compact round form, maintenance intervals can be optimised and process stability improved. Order procurement and technical advice via Metav Werkzeuge or consult the product specialists for application-specific recommendations. RDGT2006M0-G88 WK10 milling indexable insert — G88 chipbreaker, 15° clearance — Walter Tools A RDGT2006M0-G88 WK10 milling indexable insert engineered for general milling operations where stable chip formation and predictable cutting behaviour are required. Uncoated carbide grade WK10 G88 chipbreaker for reliable chip control 15° clearance for versatile milling Round insert Ø20, thickness code 06 Predictable chip formation and process stability The combination of the G88 chipbreaker and the uncoated WK10 grade provides consistent chip shaping, which supports stable cutting forces and predictable tool behaviour. The insert’s design reduces the risk of irregular chips that can interrupt the machining process, so cycle times are more repeatable. Where component quality and uninterrupted production are priorities, the controlled chip flow lowers the likelihood of rework and machine stoppages while enabling efficient chip evacuation from the cutting zone. Flexible geometry for varied milling tasks Featuring a 15° clearance angle and a round profile, the insert allows flexible application across a range of milling set-ups. The round shape offers multi-directional engagement and supports smooth entry and exit during interrupted cuts. The clearance angle helps manage cutting engagement and tool life when operations require varying depths of cut or differing radial immersion. The geometry is suitable for integration into standard cutter bodies that accept round inserts with the stated size code. Practical choice for workshop integration Manufactured as an uncoated cemented carbide insert within the Walter range, this component is intended as a pragmatic solution for production environments that need consistent performance without specialised coatings. The open series designation indicates that the insert belongs to a family where grade and chipbreaker are matched for broad applicability; the specific workpiece compatibility should be confirmed against the product matrix. Selection is thus guided by matching the WK10 grade and the G88 chipbreaker to the machining task at hand. Tolerance and handling information for reliable results Produced to tolerance class G and supplied in execution code T, the insert is dimensionally controlled to support repeatable clamping and re-indexing. The size and thickness are provided as product codes (insert size 20, thickness code 06) to align with tooling catalogues and holder specifications. For upgrade or replacement planning, note the ISO designation and series details so that tool assemblies remain consistent; the insert form and chipbreaker characteristics will determine cutting parameters and expected wear behaviour. Contact Metav Werkzeuge for tailored advice on Walter Tools RDGT2006M0-G88 WK10 inserts, application suitability and supply options. Technical data Article number: RDGT2006M0-G88-WK10-WALTER Name: Fräswendeschneidplatte / milling indexable insert Brand: Walter Tools ISO designation: RDGT2006M0-G88 WK10 Series: Walter Schneidstoffsorte - Serie offen Core specifications Insert size: 20 Thickness code: 06 Clearance angle: 15° Chipbreaker: G88 Tolerance class: G Execution: T Design & special features Round plate form Uncoated cemented carbide — grade WK10 G88 chip control geometry Open series designation for flexible grade assignment FAQ What materials is this insert intended for? The RDGT2006M0-G88 WK10 insert is supplied as an uncoated carbide grade and the specific material suitability should be checked against Walter Tools’ product matrix; the designation WK10 indicates an uncoated cemented carbide suited for general milling tasks. How does the G88 chipbreaker affect machining? The G88 chipbreaker shapes chips to improve evacuation and reduce the risk of entanglement; this results in a steadier cutting process when using the RDGT2006M0-G88 WK10 insert. Which cutter bodies accept this insert form? Round inserts with the given size code are compatible with cutters designed for round-form indexable inserts; verify the cutter’s seat and clamping arrangement against the insert ISO designation before assembly. Is the 15° clearance angle suitable for steep entry angles? A 15° clearance provides a compromise between edge strength and entry geometry, enabling versatile engagement in a variety of milling strategies while maintaining stable cutting forces. What does tolerance class G mean for re-indexing accuracy? Tolerance class G defines dimensional accuracy to ensure consistent clamping and repeatable positioning when replacing or re-indexing inserts, supporting predictable tool performance. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Die Walter AG (market appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, factory-new product of the manufacturer.
RDGT2006M0-G88 WXN15 Wendeplatten - Walter Tools
Take advantage of the combination of a sharp, uncoated carbide grade and a G88 chipbreaker for reliable, high‑quality machining of non‑ferrous materials; request application advice or order the RDGT2006M0‑G88 WXN15 directly via Metav Werkzeuge if needed. RDGT2006M0‑G88 WXN15 milling insert — round geometry, 15° clearance, Walter Tools A RDGT2006M0‑G88 WXN15 milling insert engineered for sharp, uncoated‑carbide performance when machining non‑ferrous metals such as aluminium, copper and brass Round 20 size insert 15° clearance angle for sharp cutting Uncoated carbide grade WXN15 G88 chipbreaker for non‑ferrous metals Engineered for consistent non‑ferrous performance The insert is based on the WXN15 grade: an uncoated carbide designed for machining non‑ferrous metals (N). This means the combination of a very sharp cutting edge and a low‑adhesion substrate minimises material build‑up on the edge, which reduces rework and improves surface quality. For operations in aluminium, copper or messing (brass), the sharp geometry lowers cutting forces and helps maintain cycle time while preventing smearing and galling that can compromise finishes. Precision geometry for cleaner chips and reliable cutting A round insert form combined with the G88 chipbreaker promotes predictable chip formation and evacuation in high‑feed or light‑cut milling of soft alloys. The specified 15° clearance supports a positive cutting action and reduces rubbing on the flank, which in turn keeps temperatures lower at the cutting zone. The result is improved tool life and a more consistent part finish; the chipbreaker helps avoid long, stringy chips that can interrupt automated processes or require additional handling. Productivity through stable tool behaviour and easy integration Belonging to the Walter N‑grade system, this insert is intended for production environments that demand repeatable results and straightforward tooling decisions. The simple, uncoated carbide chemistry offers predictable wear characteristics and is suited to sharp‑edge strategies where coatings could blunt the initial geometry. Integration into existing cutter bodies is straightforward thanks to conventional seat design, so the element can be introduced without disrupting tool inventories while supporting higher throughput and lower scrap rates. Contact Metav Werkzeuge for tailored application advice and availability of the Walter Tools RDGT2006M0‑G88 WXN15 milling insert at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: RDGT2006M0-G88-WXN15-WALTER Article designation: RDGT2006M0-G88 WXN15 Product type: milling insert Series: Walter N‑grade system Grade: WXN15 Execution: T Core data Plate size: 20 Plate thickness: 06 Clearance angle: 15° Tolerance class: G Design / Special features Round geometry Chipbreaker: G88 Material group: N (non‑ferrous metals) Uncoated carbide Sharp cutting edge for sticky alloys FAQ What materials is this insert suited for? The RDGT2006M0‑G88 WXN15 insert is optimised for non‑ferrous metals such as aluminium, copper and brass (ISO group N), offering low adhesion and clean chip control. Is the cutting material coated or uncoated? This grade is an uncoated carbide (WXN15), chosen to preserve an initially sharp edge for superior results in soft, adhesive materials. How does the G88 chipbreaker affect machining? The G88 chipbreaker shapes and breaks chips reliably when milling non‑ferrous alloys, reducing long continuous chips and improving process stability. Can this insert be used in high‑feed pocketing operations? Yes; the round geometry combined with the 15° clearance and G88 chip control supports high‑feed and finishing passes in soft metals, delivering consistent surface quality. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanation only. There is no affiliation between our company and the brands named. The offered item is an original, factory‑new product from Walter Tools.
RDGX07T1M0-G88 WK10 Wendeplatten - Walter Tools
Benefit from the combination of economical, general-purpose WK10 carbide and a 15° relief angle for consistent milling results; the round geometry and G88 chipbreaker promote reliable chip control and stable cutting. Order the insert directly via Metav Werkzeuge or consult the technical advisors for process matching. RDGX07T1M0-G88 WK10 milling indexable insert — round geometry, 15° relief | Walter Tools A RDGX07T1M0-G88 WK10 milling indexable insert engineered for versatile face and peripheral milling where robust chip control and economical uncoated carbide performance are required. Round insert for flexible milling applications 15° relief angle for reduced cutting forces Uncoated carbide WK10 for general-purpose machining T1 thickness in compact, stable design Consistent performance from an economical uncoated grade The WK10 grade is an uncoated carbide developed for broad, general-purpose machining tasks. Its composition supports stable chip formation and predictable wear behaviour, which helps to reduce process variance in high-volume production. Because the grade is catalogue-dependent for exact material variants, checking the product matrix before application is recommended; this ensures the chosen insert aligns with the specific workpiece material and cutting conditions. The result is a pragmatic balance of tool life and cost-efficiency for many industrial milling operations. Geometry and chip control that support reliable machining The combination of a round geometry, a 15° relief angle, and the G88 chipbreaker is designed to lower cutting forces and guide chips away from the cutting zone. Round inserts distribute cutting loads evenly, which reduces vibration in interrupted cuts and when entering or exiting the workpiece. The compact T1 thickness contributes to secure clamping and mechanical stability. Together, these features lead to steadier surface finishes and fewer rejects in continuous production environments. Process advantages and selection guidance The open series designation indicates flexible application ranges; selection should be based on the specific workpiece and cutting data. For economically driven milling tasks where an uncoated solution is acceptable, this insert offers straightforward performance without the complexity of specialised coatings. Interpreting technical terms: an uncoated carbide insert provides solid hardness and wear resistance but typically requires careful speed and feed selection compared with coated grades. The tolerance class G supports reproducible seating and interchangeability across compatible toolholders. Practical considerations for production integration When integrating this insert into a toolset, consider the intended milling strategy: finishing passes benefit from the insert’s stable edge and chip control, while roughing strategies should factor in appropriate feeds to exploit the round geometry’s load distribution. The open-series material description and the catalogue-dependent material variants mean that process engineers should verify compatibility with aluminium, steel, stainless or other workpiece families using the available product documentation. Proper combination of cutting data and toolholder rigidity will unlock the insert’s dependable behaviour in series machining. For economical, dependable milling with Walter Tools’ WK10 uncoated carbide, contact Metav Werkzeuge for selection support and fast availability: info@metav-werkzeuge.com, +49 2822 7131930. Technical Data SKU: RDGX07T1M0-G88-WK10-WALTER Article designation: RDGX07T1M0-G88 WK10 Product type: Milling indexable insert Brand: Walter Tools Core data Geometry: Round Size: 07 Thickness: T1 Relief angle: 15° Chipbreaker: G88 Tolerance class: G Special features Grade: WK10 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Execution: X Material specification: catalogue-dependent FAQ What materials is this insert suitable for? The RDGX07T1M0-G88 WK10 insert is a general-purpose, uncoated carbide grade; material suitability should be verified in the manufacturer’s product matrix to ensure optimal cutting data for the intended workpiece. How does the 15° relief angle affect milling performance? A 15° relief reduces cutting forces and improves chip formation behaviour, helping the insert maintain stability and produce consistent surface quality during face and peripheral milling operations. What advantage does the round geometry provide compared with polygonal inserts? Round geometry distributes cutting loads more evenly, which increases resistance to vibration in interrupted cuts and improves edge life under variable engagement conditions. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners and are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product from the manufacturer.
RDGX1604M0-G88 WK10 RDGX1604M0-G88 WK10 Wendeplatten - Walter Tools
Benefit from the combination of uncoated carbide WK10, a G88 chipbreaker and the compact round Ø16 form for steady milling performance; order the RDGX1604M0-G88 WK10 directly via Metav Werkzeuge or ask our consultants if needed. RDGX1604M0-G88 WK10 – Milling indexable insert, round Ø16, 15° relief | Walter Tools The RDGX1604M0-G88 WK10 is a round milling indexable insert engineered for reliable chip control and consistent cutting geometry in general milling operations. Uncoated carbide grade WK10 G88 chipbreaker for controlled chips Round insert Ø16 with 15° relief Consistent cutting performance for repeatable results The combination of the WK10 grade and an uncoated carbide substrate offers a balance between cost-efficiency and predictable wear behaviour. The G88 chipbreaker is designed to produce short, manageable chips for many milling tasks, which supports uninterrupted production and reduced secondary handling. For workshop planners and production engineers, the main advantage is the predictable tool behaviour: stable edge geometry contributes to precision and repeatable part quality over multiple indexing cycles. Note that specific workpiece compatibility should be verified against the manufacturer product matrix. Robust round geometry and reduced rubbing at the cutter seat A round insert shape with a nominal diameter of Ø16 provides multiple effective cutting positions and generally increases the insert’s resistance to impact compared with sharper corner geometries. The 15° relief angle lowers the likelihood of flank rubbing during engagement, which helps maintain surface finish and reduces heat build-up at the cutting edge. As an indexable insert, it enables quick edge rotation and straightforward replacement, supporting short tool-change times and efficient machine utilisation. Selection advice and simple integration into existing processes Selection of the correct grade and geometry is key for process stability. The RDGX1604M0-G88 WK10 is delivered as part of the Walter Schneidstoffsorte – Serie offen; the material specification is catalogue-dependent, so suitability for specific materials must be confirmed via the product matrix. For technical clarification or to match the insert to a particular machining application, the supplier can provide detailed data sheets and cutting parameters. If additional information is required, Metav Werkzeuge can be contacted for tailored advice. For process optimisation or a material-specific recommendation for the RDGX1604M0-G88 WK10, contact Metav Werkzeuge for expert support and specify the insert designation for prompt guidance. Technical data SKU: RDGX1604M0-G88-WK10-WALTER Label: Fräswendeschneidplatte RDGX1604M0-G88 WK10 Walter Tools Manufacturer: Walter Tools UID: RDGX1604M0-G88-WK10-WALTER Facts Relief angle: 15° Size: 16 Thickness code: 04 Tolerance class: G Design & features Grade: WK10 Chipbreaker: G88 Series: Walter Schneidstoffsorte - Serie offen Execution: X Plate form: Round Material specification: Katalogabhängig ISO designation: RDGX1604M0-G88 WK10 Base designation: RDGX1604M0-G88 Product type: Fräswendeschneidplatte FAQ What types of machining tasks is this insert intended for? The RDGX1604M0-G88 WK10 insert is engineered for a range of general milling tasks where a round insert geometry and controlled chip formation are advantageous; exact suitability depends on the specific workpiece and cutting conditions. Does the G88 chipbreaker improve surface finish? Yes, the G88 chipbreaker is designed to promote consistent chip formation and evacuation, which can contribute to improved surface finish and fewer issues with chip entanglement. How many cutting edges are usable on the round insert? A round insert provides multiple equivalent cutting positions through indexing; the exact number of indexes depends on the seat and clamping arrangement used in the toolholder for the insert. Where can the detailed cutting data and recommended feeds/speeds be found? Detailed cutting parameters and the material compatibility matrix are available from the manufacturer or Metav Werkzeuge; these documents should be consulted before finalising process settings. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation purposes only. There is no connection between our company and the mentioned brands. The offered article is an original, factory-new product of the manufacturer.
RDHW0803M0-A57 WHH15X Wendeplatten - Walter Tools
Reliable productivity through a combination of the WHH15X cutting grade and the A57 chipbreaker supports stable chip formation and consistent cutting performance. The 15° relief and round geometry deliver flexible milling capability while maintaining dimensional control — order directly via Metav Werkzeuge or consult our specialists for application-specific advice. RDHW0803M0-A57 WHH15X milling indexable insert — 15° relief, A57 chipbreaker — Walter Tools The RDHW0803M0-A57 WHH15X is a round milling indexable insert designed for use in rotary milling cutters where stable chip control and repeatable performance are required. Round insert, size 08, thickness 03 15° relief for consistent cutting Chipbreaker A57 for controlled chips Stable chip control for continuous productivity The combination of the A57 chipbreaker and the WHH15X grade is engineered to improve chip control and reduce process interruptions. The chip geometry promotes stable chip formation, which reduces the need for manual intervention and helps maintain a steady metal removal rate. For production environments this means fewer stoppages for chip clearing and a more predictable tool life, supporting higher throughput and lower overall operating costs. The design also aids coolant flow and evacuation, improving thermal stability during longer machining cycles. Precision geometry and tolerance for reliable parts The round geometry with a 15° relief and the designation tolerance class H ensure consistent seating and repeatable positioning in the cutter body. The size 08 and thickness 03 give a balanced contact area that supports stable cutting forces and predictable wear progression. For engineers and buyers, the geometric data translate into dependable repeatability in serial production: consistent tool engagement leads to consistent component dimensions and surface results. Where corner rounding or profile continuity is required, the round insert form offers flexibility while maintaining control over radial and axial run-out. Selection guidance and practical application notes The insert is delivered in the WHH15X coated-carbide grade (series open) — a modern coated hardmetal option that must be matched to the workpiece material via the manufacturer's product matrix. Suitability for specific materials should be checked against the technical matrix before use; the grade is intended for broad applicability but the final choice depends on cutting speed, feed and component requirements. For workshop planners and process engineers, the clear designation of chipbreaker, relief angle and tolerance class simplifies tool selection and inventory management. When paired with the correct cutter body and clamping system, the insert supports productive and consistent milling operations across a range of tasks. For application advice or to secure stock of Walter Tools inserts in the WHH15X grade, contact Metav Werkzeuge for tailored recommendations and availability Technical Data SKU: RDHW0803M0-A57-WHH15X-WALTER Article: RDHW0803M0-A57 WHH15X Manufacturer: Walter Tools Facts Relief angle: 15° Size: 08 Thickness: 03 Tolerance class: H Special features Chipbreaker: A57 Shape: Round Grade: WHH15X (coated hardmetal) Series: Walter Schneidstoffsorte - Serie offen FAQ What is the primary benefit of the A57 chipbreaker? The A57 chipbreaker promotes controlled chip formation and easy evacuation; it is intended to reduce interruptions and support continuous milling cycles with the RDHW0803M0-A57 WHH15X insert from Walter Tools. Which cutting grade is used and what does it mean? The insert uses the WHH15X coated hardmetal grade; this modern coating improves wear resistance and is suitable for a wide range of milling tasks when matched to the correct cutting parameters. How does the 15° relief influence performance? A 15° relief angle reduces radial cutting forces and enhances edge engagement stability, contributing to smoother cutting action and predictable insert life in rotary milling applications. Is the RDHW0803M0-A57 WHH15X suitable for all materials? Material suitability depends on the specific product matrix; the WHH15X grade is broadly applicable, but users should verify compatibility with the intended workpiece material and operating conditions. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and product names are the property of their respective owners and are used here for clarification only. There is no affiliation between our company and the trademark holders. The offered item is an original, factory-new product from Walter Tools.
RDHW10T3M0-A57 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of WHH15X coated carbide performance, precise 15° clearance geometry and reliable chip control for consistent milling results; order the insert via Metav Werkzeuge or consult the team for application advice. RDHW10T3M0-A57 WHH15X Walter Tools — round milling indexable insert with 15° clearance RDHW10T3M0-A57 WHH15X is a round indexable milling insert designed for controlled chip formation and productive cutting in a wide range of industrial milling tasks. Coated carbide grade WHH15X A57 chipbreaker for stable chips 15° clearance for smooth engagement Round plate, designation 10 Increase machining productivity with reliable chip control The combination of the WHH15X coating and the A57 chipbreaker provides consistent chip formation, which directly reduces unexpected interruptions and improves process stability. A stable chip flow reduces the risk of re-cutting and heat concentration at the cutting edge, extending tool life and contributing to higher machine utilisation. The insert’s construction as a coated carbide indexable insert supports higher feed rates and repeatable results on demanding production schedules. Achieve precise engagement and repeatable geometry The round plate geometry (designation 10) together with a 15° clearance angle ensures a gentle workpiece entry and a predictable cutting force distribution. The plate thickness T3 and the execution W are selected to balance stiffness and accessibility for close-tolerance pockets and shoulder milling. Tolerance class H supports repeatable seating accuracy in standard toolholders, which helps to maintain consistent surface finish and dimensional stability across series production. Simple selection and targeted application guidance This insert is part of the Walter Schneidstoffsorte – Serie offen and is designed as a coated hardmetal grade; suitability for specific materials should be checked against the manufacturer’s product matrix before final selection. For materials or operations not explicitly listed, matching the chipbreaker and grade to the workpiece and cutting data will deliver the best economic outcome. Technical advisors at Metav Werkzeuge can provide cutting data comparisons and recommendations for optimised feed and speed settings to achieve the desired balance of tool life and surface quality. For tailored procurement and technical advice on Walter Tools’ WHH15X milling inserts, contact Metav Werkzeuge for expert selection and prompt delivery at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical Data Article number: RDHW10T3M0-A57-WHH15X-WALTER Label: Fräswendeschneidplatte RDHW10T3M0-A57 WHH15X Walter Tools Product type: Fräswendeschneidplatte Facts Plate size: 10 Plate thickness: T3 Clearance angle: 15° Tolerance class: H Special features Chipbreaker: A57 Grade: WHH15X (coated carbide) Shape: Round Series: Walter Schneidstoffsorte - Serie offen Execution: W Material: Katalogabhängig FAQ What materials is this insert suitable for? Suitability depends on the specific material matrix; the RDHW10T3M0-A57 WHH15X insert (Walter Tools) is a coated carbide grade intended for a broad range of applications—check the product matrix for exact workpiece compatibility. How does the A57 chipbreaker affect machining? The A57 chipbreaker on the RDHW10T3M0-A57 WHH15X promotes short, controlled chips and stable evacuation, improving process reliability and reducing tool-change frequency. What does the 15° clearance angle mean in practice? A 15° clearance provides a gentle entry angle that reduces cutting forces and improves surface finish; this geometry helps the insert maintain edge stability during interrupted cuts. Is this insert compatible with standard round toolholders? The round plate form and tolerance class H allow the RDHW10T3M0-A57 WHH15X to be used in compatible round-seat toolholders; verify holder compatibility with the tool supplier before assembly. How should cutting data be adjusted for this grade? Cutting data should be adapted to the material and operation; the WHH15X coating supports productive machining, and Metav Werkzeuge can provide tailored recommendations for speed and feed. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
RDHW1204M0-A57 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of long tool life and reliable chip control provided by the coated carbide grade and the A57 chipbreaker; the 15° relief geometry supports versatile milling and consistent surface quality. Order RDHW1204M0-A57 WHH15X via Metav Werkzeuge or consult our experts for application-specific guidance. RDHW1204M0-A57 WHH15X – milling insert, 15° relief (Walter Tools) RDHW1204M0-A57 WHH15X is a round, coated carbide milling insert with a 15° relief angle, designed for versatile milling tasks where stable chip formation and repeatable cutting performance are required Coated carbide grade WHH15X 15° relief angle for versatile milling Round insert, size 12, thickness 04 A57 chipbreaker ensures consistent chips Enhanced process stability through modern carbide technology The RDHW1204M0-A57 WHH15X insert is manufactured in a coated carbide grade engineered for balanced wear resistance and toughness. The WHH15X grade provides a compromise between hardness and edge protection that supports sustained cutting under varied conditions. This characteristic translates directly into reduced tool changes and fewer interruptions on production runs, increasing overall throughput. For precise results, the cutting-grade selection and the series description should be verified against the product matrix to confirm suitability for specific workpiece materials. Geometry designed for controlled chips and reliable surface finish A geometry combining a 15° relief angle with the round shape and the A57 chipbreaker delivers predictable chip formation and improved evacuation. The controlled chip flow reduces the risk of built-up edge and helps maintain a steady cutting force, which in turn supports a more consistent surface finish. The round form factor benefits operations that require multi-directional engagement and contributes to even wear distribution across the cutting edge, enhancing process reliability and part quality. Simple integration into existing tooling systems With a size 12 diameter and thickness 04, this round insert fits standard indexable milling cutter bodies that accept the RDHW geometry. The execution designation W and tolerance class H ensure mechanical compatibility and repeatable seating in appropriate holders. Because the exact substrate and coating details are catalogue dependent, workshops should consult the technical matrix for matching tool holders and clamping systems. These dimensional and tolerance details simplify inventory management by aligning with common toolholder standards. Economic machining through longer intervals between changes The combination of the WHH15X cutting grade and the A57 chipbreaker is aimed at extending tool life while maintaining consistent performance across batches. Longer wear resistance lowers the frequency of insert replacements and reduces unplanned downtime, contributing to lower unit machining costs. This insert supports productive milling operations where steady performance and reproducible results are priorities; for specific material classes and process windows, refer to the manufacturer’s application matrix to confirm expected productivity gains. For availability, technical data sheets or application advice on Walter Tools inserts such as the RDHW1204M0-A57 WHH15X, contact Metav Werkzeuge for procurement and consultancy at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: RDHW1204M0-A57-WHH15X-WALTER Label: Fräswendeschneidplatte RDHW1204M0-A57 WHH15X Walter Tools Internal designation: RDHW1204M0-A57 ISO designation: RDHW1204M0-A57 WHH15X Grade: WHH15X Execution: W Series: Walter Schneidstoffsorte - Serie offen Tolerance class: H Manufacturer: Walter Tools Dimensions & core data Relief angle: 15° Insert shape: Round Size: 12 Thickness: 04 Chipbreaker: A57 Materials & special features Cutting grade: coated carbide (WHH15X) Material data: catalogue dependent Sort description: coated cemented carbide Application note: Check product matrix for material suitability FAQ What materials can this insert machine effectively? Material suitability for the RDHW1204M0-A57 WHH15X must be checked in the manufacturer’s product matrix; the grade is a coated carbide designed for a broad range of applications, but specific workpiece materials and cutting conditions determine the optimum use. How does the A57 chipbreaker affect machining? The A57 chipbreaker creates short, consistent chips and improves evacuation, reducing the likelihood of chip entanglement and helping to maintain a stable cutting edge during interrupted and continuous milling operations with this insert. Which geometry details are critical when selecting a toolholder? Key data points are the round insert form, size 12, thickness 04, and 15° relief; matching these to a compatible cutter body and ensuring the tolerance class H is supported will ensure secure seating and repeatable results. Is the coating specified for this insert? Coating and substrate details are catalogue dependent for this product; the RDHW1204M0-A57 WHH15X is described as a coated carbide grade, and exact coating information should be confirmed from the technical datasheet or product matrix. What distinguishes the WHH15X grade in production use? The WHH15X grade is a Walter Tools cutting-grade offering balanced wear resistance and toughness, optimised for stable chip formation and consistent edge life when used within the recommended application window. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only and do not imply any affiliation between our company and the named manufacturers. The offered article is original, factory-new goods of Walter Tools.
RDHW1605M0-A57 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of a WHH15X coated carbide grade, chipbreaker A57 and a 15° clearance geometry for predictable milling performance and consistent chip control; order the insert via Metav Werkzeuge or consult the specialists for application support. RDHW1605M0-A57 WHH15X — Round milling insert, 15° clearance by Walter Tools The RDHW1605M0-A57 WHH15X is a round milling insert designed for versatile milling applications where reliable chip control and a predictable cutting geometry are required Round form, size 16 15° clearance angle for versatile cutting WHH15X coated carbide grade Integrated chipbreaker A57 for chip control Consistent wear resistance and productivity The WHH15X grade is a coated carbide composition developed for stable cutting performance and extended tool life in a variety of milling tasks. Combined with the chipbreaker A57, the geometry supports controlled chip fragmentation, reducing re-cutting and improving surface quality. This results in fewer interruptions for tool changes and a more stable process, which supports higher overall productivity without speculative claims about specific materials. Predictable cutting geometry for repeatable results A 15° clearance angle and round plate form deliver a robust contact geometry that stabilises tool engagement and load distribution during interrupted and continuous milling. The tolerance class H ensures consistent dimensions between inserts, which assists in repeatable set-ups and predictable component quality. Selected geometry features focus on process security and ease of integration into existing tool systems. Easy integration and application guidance With an insert size of 16 and thickness designation 05, the plate fits holders designed for the RDHW1605M0-A57 family; the execution W indicates the insert seating and clamping style. Material suitability must be confirmed using the manufacturer’s product matrix, since the grade is optimised across a range of workpiece materials. For engineering teams, this means assessing the matrix against the intended workpiece before final selection to ensure optimal cycle times and surface integrity. Practical handling and procurement for production use The open series designation and catalogue-dependent material listing reflect a product intended for professional workshop environments where matching insert, holder and machining parameters is routine. The combination of coated carbide and a dedicated chipbreaker supports stable chip control and predictable tool wear, which simplifies inventory decisions and reduces process variation when the tool is applied according to the documented matrix and holder specifications. For applications demanding reliable chip control and consistent wear performance with WHH15X-coated carbide, contact Metav Werkzeuge for ordering and application advice. Technical data SKU: RDHW1605M0-A57-WHH15X-WALTER Article: Fräswendeschneidplatte RDHW1605M0-A57 WHH15X Manufacturer: Walter Tools Facts Insert size: 16 Thickness: 05 Clearance angle: 15° Tolerance class: H Special features Grade: WHH15X (coated carbide) Chipbreaker: A57 Shape: Round Execution: W Series: Walter Schneidstoffsorte - Serie offen Material: Katalogabhängig ISO designation: RDHW1605M0-A57 WHH15X Note: Check material suitability with product matrix FAQ What materials is this insert suitable for? Material suitability must be checked using the Walter Tools product matrix; the WHH15X grade is a coated carbide intended for a broad range of applications, but specific compatibility depends on the workpiece. How does the A57 chipbreaker affect machining? The chipbreaker A57 promotes controlled chip formation and evacuation, reducing the risk of long, entangling chips and improving surface finish in typical milling operations. What does the 15° clearance angle mean for operation? A 15° clearance angle provides a balance between strength and cutting-edge exposure, offering stable engagement with the workpiece and predictable cutting forces in many milling scenarios. Is the insert compatible with standard RDHW holder systems? The insert follows the RDHW1605M0-A57 designation and is intended for holders designed for that family; confirm compatibility with the specific toolholder geometry before assembly. Is this an original Walter Tools product? The article is offered as a factory-new insert specified under the Walter Tools grade WHH15X and the RDHW1605M0-A57 designation Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com