WNMG100616-RP7 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, the wear-resistant WPP20G grade and the Trigon 80° geometry with a 1.6 mm corner radius for dependable steel machining; order the WNMG100616-RP7 WPP20G directly via Metav Werkzeuge or ask our consultants if needed WNMG100616-RP7 WPP20G indexable turning insert — Tiger·tec Gold for steel (Walter Tools) WNMG100616-RP7 WPP20G is an 80° trigon indexable turning insert designed for robust and consistent turning of steels Tiger·tec Gold coated grade WPP20G for steel Trigon 80° geometry with 1.6 mm corner radius 0° negative rake for stable cutting RP7 chipbreaker for reliable chip control Enhanced process reliability for steel machining The combination of Tiger·tec Gold coating and the WPP20G substrate delivers high resistance to abrasive wear while maintaining toughness where thermal and mechanical loads are highest. This grade is tailored for machining steel in the ISO P group, including unalloyed and alloyed steels, and is optimised to cope with the heat and chip formation typical of steel turning. The result is a more predictable tool life and fewer interruptions to production, which supports cost-efficient machining sequences without compromising component quality. Geometry that stabilises cutting and extends edge life The Trigon 80° form and 1.6 mm corner radius provide a good balance between strength and accessibility for shoulder and general turning operations. The 0° negative clearance configuration increases cutting-edge support under higher radial loads, reducing vibration and edge chipping during interrupted cuts. This geometry permits more aggressive engagement where stability is required, translating to improved productivity on medium-duty turning tasks while protecting the cutting edge. Controlled chips and consistent surface finish The RP7 chipbreaker has been developed to produce predictable chip shapes under typical steel cutting conditions, aiding evacuation and preventing entanglement. Effective chip control reduces secondary machining time and minimises the risk of surface damage, helping to achieve repeatable surface quality. Clear understanding of the chipbreaker behaviour enables process engineers to select appropriate feeds and depths of cut for either stable roughing or controlled finishing operations. Practical application notes and procurement guidance This insert is intended primarily for machining operations in the ISO P material class; the grade covers a range from wear-resistant to universally applicable and tougher cutting tasks. For best results, match the insert geometry to a suitably rigid toolholder and ensure correct clamping to maintain the intended cutting angle and edge support. The indexable format simplifies tool changes and inventory management. Availability and technical guidance are provided via Metav Werkzeuge for straightforward integration into existing tool families. For detailed application advice on Walter Tools Tiger·tec Gold inserts or to discuss optimal parameters for specific steel grades, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt expert assistance. Technical Data SKU: WNMG100616-RP7-WPP20G-WALTER Designation: WNMG100616-RP7 WPP20G Product type: Indexable turning insert Manufacturer: Walter Tools Series: Tiger·tec Gold Core specifications Plate shape: Trigon 80° Plate size: 10 Plate thickness: 06 Corner radius: 1.6 mm Clearance angle: 0° (negative) Tolerance class: M Special features Grade: WPP20G Chipbreaker: RP7 Coating technology: Tiger·tec Gold Material application: Steel (ISO P) Execution: G FAQ Which materials is this insert suitable for? The WNMG100616-RP7 WPP20G indexable turning insert is specified for machining steel and conforms to ISO P material applications, covering unalloyed and alloyed steels. What advantage does the Tiger·tec Gold technology provide? Tiger·tec Gold on the WNMG100616-RP7 WPP20G increases wear resistance while preserving toughness, resulting in longer tool life and consistent performance on steel turning tasks. How does the RP7 chipbreaker affect machining? The RP7 chipbreaker on this Walter Tools insert produces controlled chip forms under typical steel cutting conditions, aiding evacuation and reducing risk of surface damage. When is the Trigon 80° geometry most appropriate? The Trigon 80° form is well suited for general turning and shoulder operations where a balance of cutting-edge strength and accessibility is required. Does the 0° negative clearance change holder selection? A rigid, appropriately sized toolholder is recommended to exploit the 0° negative clearance of the insert; correct clamping ensures edge support and stability during heavier cuts. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
WNMG100616-RP7 WPP30G G Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, dependable chip control and the Tiger·tec Gold coating for consistent turning performance; order the insert directly via Metav Werkzeuge or consult the team for application advice. WNMG100616-RP7 WPP30G – Trigon 80° turning insert for Stahl, Tiger·tec Gold (Walter Tools) WNMG100616-RP7 WPP30G is a negative‑rake trigon insert designed for precision turning of Stahl with stable chip formation and extended tool life Tiger·tec Gold coating for extended tool life Grade WPP30G for reliable Stahl machining Trigon 80° geometry for secure cutting edge 1.6 mm corner radius for robust performance Maximise throughput with coated‑carbide performance The combination of the Tiger·tec Gold coating and the WPP30G grade provides a balanced response to wear and toughness, enabling higher throughput in many turning applications. As a coated carbide insert, the component is engineered to resist flank wear while maintaining a stable cutting edge, which reduces the frequency of index changes and supports continuous production. This results in measurable process reliability and predictable tool life when machining common Stahl alloys. Reliable chip control and edge stability for consistent surfaces The RP7 chipbreaker, paired with the Trigon 80° plate form and a 1.6 mm corner radius, gives consistent chip control and secure edge engagement. The negative 0° free angle improves edge strength in interrupted or heavy‑cut conditions and helps avoid premature edge chipping. Together these design choices support a predictable surface finish and repeatable dimensional results, reducing rework and enhancing downstream quality assurance. Clear material focus and process transparency This insert is specified for the ISO P group, i.e. machining of Stahl such as unalloyed and alloyed steels; the grade composition is tuned to the thermal and chip‑forming characteristics common to these materials. The specification emphasises a practical balance: good wear resistance for longer tool life with sufficient toughness to withstand moderate interruptions. For engineers unfamiliar with cutting grades, the WPP30G designation denotes a coated, general‑purpose grade within the Tiger·tec Gold family suitable for a wide range of turning tasks in Stahl. Practical integration into production and on‑shop guidance The insert geometry and chipbreaker simplify process setup: secure clamping in the appropriate insert seat and conservative starting parameters allow rapid optimisation of cutting speed and feed. For practical process data, application sheets from Walter Tools are recommended; Metav Werkzeuge can provide support with recommended starting values for different Stahl groups and advise on index change strategies to prolong overall cutting tool economy. This combination of technical clarity and supplier guidance helps to reduce setup time and supports reproducible machining cycles. Contact Metav Werkzeuge to discuss cutting parameters and secure genuine Walter Tools Tiger·tec Gold WPP30G inserts for reliable Stahl machining Technical Data SKU: WNMG100616-RP7-WPP30G-WALTER Designation: WNMG100616-RP7 WPP30G Type: Turning insert Series: Tiger·tec Gold Grade: WPP30G Manufacturer: Walter Tools Chipbreaker: RP7 Plate form: Trigon 80° Free angle: 0° (negative) Corner radius: 1.6 Plate size: 10 Plate thickness: 06 Tolerance class: M Facts Corner radius: 1.6 mm Free angle: 0° (negative) Plate form: Trigon 80° Size designation: 10 Thickness designation: 06 Tolerance class: M Special features Coating/grade: WPP30G (coated carbide, Tiger·tec Gold) Intended material group: P (Stahl) Chip control: RP7 chipbreaker Geometry benefit: Trigon geometry for edge security Application focus: General‑purpose turning of Stahl FAQ What materials is the insert suitable for? The WNMG100616-RP7 WPP30G is specified for ISO group P, i.e. machining of Stahl such as unalloyed and alloyed steels; the grade is tuned to typical heat and chip‑forming behaviour in these materials. How does the Tiger·tec Gold coating improve performance? The Tiger·tec Gold coating on the WPP30G grade enhances wear resistance while maintaining edge toughness, which extends tool life and supports consistent surface quality during turning operations. What advantages does the Trigon 80° shape offer? The Trigon 80° plate form provides a secure cutting edge and multiple effective cutting corners, combined with the RP7 chipbreaker it ensures reliable chip control and robust performance in standard turning tasks. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanation only and do not indicate any affiliation between our company and the named brands. The article offered is an original, factory‑new product from the manufacturer Walter Tools.
WNMM080412-HU3 WPP20G HU3 Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold performance and the robust Trigon geometry for reliable, cost-effective steel turning; the WPP20G coating extends tool life while the HU3 chipbreaker improves chip control in demanding cuts. Order suitable inserts through Metav Werkzeuge or consult their technical advisors for process optimisation. WNMM080412-HU3 WPP20G indexable turning insert — Tiger·tec Gold, for steel (Walter Tools) A WNMM080412-HU3 WPP20G indexable turning insert engineered for high-productivity steel machining, combining Tiger·tec Gold coating with a HU3 chipbreaker and Trigon 80° geometry. Tiger·tec Gold coated carbide grade WPP20G Trigon 80° geometry for secure clamping HU3 chipbreaker for predictable chip control 1.2 mm corner radius with 0° negative rake Durable coating and longer cutting edge life for steady output The Tiger·tec Gold coating and the WPP20G coated carbide grade deliver noticeably improved wear resistance under the thermal loads typical of steel machining. This results in longer tool life and fewer indexings, which reduces downtime and supports consistent batch output. The coating technology stabilises the cutting edge at elevated temperatures, so productivity gains are achieved without complex parameter changes. As a consequence, machining windows can be extended and productivity per insert rises, offering a tangible efficiency advantage for repetitive turning operations. Predictable chips and improved surface quality with the HU3 chipbreaker The dedicated HU3 chipbreaker is tuned for the cutting behaviour of steels in ISO group P and produces short, controllable chips during medium-to-heavy cutting. Predictable chip formation reduces the risk of entanglement and recutting, thereby helping to protect the workpiece surface and tool flank. Better chip control also simplifies chip evacuation in automated machining cells, contributing to safer, more reliable process routines and a cleaner machine environment. The result is improved process security and fewer interruptions. Robust geometry that supports higher metal removal rates The Trigon 80° form provides a compact, stable seat in the toolholder and resists tilting under heavy cutting forces. Combined with the 1.2 mm corner radius and the 0° negative rake, the geometry is designed to withstand interrupted cuts and higher depths of cut while maintaining a durable cutting edge. This configuration favours productive roughing passes and supports a steady transition to semi-finish operations with minimal compromise on dimensional stability. The trimmed profile also helps to reduce cutting forces where tool access is limited. Practical suitability and simple integration into tool systems The insert follows the WNMM designation and is suitable for use in toolholders that accept this indexable format, facilitating straightforward replacement in existing setups. The grade and chipbreaker are specified for steel, making the insert well suited to general turning tasks across a range of unalloyed and alloyed steels. For shops seeking to harmonise inventory, the combination of a coated carbide grade with a proven chipbreaker offers a balance between versatility and targeted performance, reducing the need for multiple special-purpose grades while maintaining consistent component quality. For machining recommendations tailored to the Walter Tools Tiger·tec Gold grade or to confirm holder compatibility for the WNMM080412-HU3 WPP20G insert, contact Metav Werkzeuge for fast technical guidance and stock information: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: WNMM080412-HU3-WPP20G-WALTER SKU: WNMM080412-HU3-WPP20G-WALTER Product type: indexable turning insert Designation: WNMM080412-HU3 WPP20G Series: Tiger-tec Gold Grade: WPP20G Manufacturer: Walter Tools Facts Insert shape: Trigon 80° Corner radius: 1.2 mm Insert size: 08 Thickness: 04 (4 mm) Rake angle: 0° (negative) Special features Coating: Tiger·tec Gold (coated carbide) Chipbreaker: HU3 Material group suitability: Steel (ISO P) Tolerance class: M Execution: M WNMM format for turning applications FAQ What materials is this insert suitable for? The WNMM080412-HU3 WPP20G insert from Walter Tools is specified for steel (ISO group P), covering unalloyed and alloyed steels with typical chip and heat characteristics. How does the HU3 chipbreaker affect machining? The HU3 chipbreaker provides predictable chip control, producing short chips in steel that reduce recutting and promote safer chip evacuation during medium-to-heavy turning operations. Is the Trigon 80° shape suitable for heavy cuts? Yes; the Trigon 80° geometry offers a secure seating and resistance to tilting, which supports higher metal removal rates and interrupted cuts when combined with the 1.2 mm corner radius and 0° negative rake. Can this insert be used for finishing passes? The insert is optimised for productive roughing and semi-finishing in steel; depending on the required surface finish, a dedicated finishing grade may be selected, but the WPP20G grade provides a good compromise for many general applications. What does the WPP20G grade mean in practice? WPP20G is a Walter coated carbide grade within the Tiger·tec Gold family. It balances wear resistance and toughness for steel machining, helping to extend tool life and maintain process stability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
WNMM100612-HU3 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of the Tiger·tec Gold coating, ISO P suitability for steel and the robust Trigon 80° geometry to secure stable, repeatable turning results; order or request application advice via Metav Werkzeuge for quick integration into production. WNMM100612-HU3 WPP10G indexable turning insert — Tiger·tec Gold, Trigon 80° (Walter Tools) The WNMM100612-HU3 WPP10G is an indexable turning insert engineered for precision steel machining with a Trigon 80° profile and a resilient coated-carbide grade. Tiger·tec Gold coated grade WPP10G Suitable for steel machining (ISO P) Trigon 80° insert for stable cutting Corner radius 1.2 mm for edge strength Consistent performance for steel turning The Tiger·tec Gold WPP10G grade is a coated carbide solution optimised for steel (ISO P), delivering a balance of wear resistance and toughness that supports longer tool life and consistent surface finish. The specialised coating reduces flank and crater wear under the thermal conditions typical in steel turning, which translates into fewer index changes and reduced machining interruptions. For production environments where repeatability matters, this insert offers measurable gains in process reliability and uptime. Geometry and edge security for productive cuts The Trigon 80° shape combined with a 1.2 mm corner radius provides a stable cutting edge for both light and interrupted cuts. A 0° rake (negative) geometry enhances edge strength, making the insert less susceptible to chipping in heavy engagement or unstable fixtures. The HU3 chipbreaker controls chip formation during common steel applications, promoting safe evacuation and consistent chip shape; this reduces the risk of surface damage and supports predictable tool behaviour in series production runs. Practical advantages in the machining process Tolerance class M and execution code M indicate a dimensionally consistent insert suitable for a wide range of toolholders and turning operations. The insert thickness code 06 and size 10 reflect a compact design that fits many standard clamping systems while still providing robust edge support. These dimensional attributes, together with the coated hardmetal grade, enable an efficient cost-in-use through longer edge life and fewer index operations, which is particularly relevant for batch production and mixed-lot machining. System compatibility and application guidance Designed by Walter Tools within the Tiger·tec Gold series, the insert is primarily intended for unalloyed and alloyed steels as classified under ISO P. The HU3 chipbreaker and the Trigon form make it suitable for a range of turning tasks from finishing to medium roughing when parameters are adapted to material and machine capability. For optimisation, pair the insert with appropriate clamping torque and a holder matching the Trigon 80° footprint to maintain positional stability and repeatable cutting performance. For reliable steel turning with Walter Tools’ Tiger·tec Gold grade, contact Metav Werkzeuge for availability and application advice: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: WNMM100612-HU3-WPP10G-WALTER Designation: WNMM100612-HU3 WPP10G Manufacturer: Walter Tools Series: Tiger·tec Gold Grade: WPP10G Shape: Trigon 80° Chipbreaker: HU3 Execution: M Tolerance class: M Material group: P Facts Insert size: 10 Thickness code: 06 Corner radius: 1.2 mm Rake angle: 0° (negative) Applicable material group: ISO P (steel) Special features Coating technology: Tiger·tec Gold Coated carbide grade for balanced wear and toughness Suited for unalloyed and alloyed steels Stable Trigon geometry for reliable clamping and cutting HU3 chipbreaker for controlled chip formation FAQ What materials is this insert designed for? The WNMM100612-HU3 WPP10G insert is designed for machining steels as defined by ISO P; the WPP10G grade is optimised for the thermal and chip-formation behaviour of steel. What does the Tiger·tec Gold grade offer? Tiger·tec Gold provides a coated-carbide combination that improves wear resistance and edge stability, making it suitable for longer runs and varied steel turning tasks. How does the Trigon 80° geometry affect cutting? A Trigon 80° profile increases the insert’s contact area for enhanced stability and clamping consistency, which supports controlled cutting forces and improved surface finish in turning. When is the HU3 chipbreaker recommended? The HU3 chipbreaker is recommended for typical steel turning where consistent chip shape and reliable evacuation are required, particularly in medium to finishing passes. What is the significance of the 1.2 mm corner radius? A 1.2 mm corner radius strengthens the cutting edge against mechanical shock and provides a balance between edge life and the achievable surface finish. The Walter AG (trading as Walter Tools) is part of the Sandvik Group and ranks among the leading manufacturers of precision tools for metalworking. Protected trademarks and product names are the property of their respective owners. Mention of brand names is for explanation only and does not imply any affiliation. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
WNMM100612-HU3 WPP20G WPP20G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating, the HU3 chipbreaker and Trigon 80° geometry for efficient, repeatable turning of Stahl components; order the WNMM100612-HU3 WPP20G indexable turning insert directly via Metav Werkzeuge or consult our application specialists for tailored advice. WNMM100612-HU3 WPP20G — Indexable turning insert with Tiger·tec Gold coating and Trigon 80° geometry (Walter Tools) The WNMM100612-HU3 WPP20G is an indexable turning insert engineered for robust, general-purpose turning of Stahl (P) where consistent chip control and reliable edge life are priorities. Tiger·tec Gold coated carbide Trigon 80° insert geometry Chipbreaker HU3 for controlled chips Corner radius 1.2 mm for stable cutting Precise machining performance for demanding turning tasks The insert’s Tiger·tec Gold coating and coated carbide substrate deliver a controlled balance between wear resistance and toughness, which translates into longer tool life and predictable results in series production. Designed for Stahl (P) applications, the Trigon 80° form combines a large rake support and a robust cutting edge to withstand interrupted cuts and moderate depths of cut. The chipbreaker HU3 promotes consistent chip formation, reducing risks of re-cutting and improving surface integrity. For engineers seeking measurable process stability, the insert offers a direct path to improved uptime and fewer in-process interruptions. Repeatable tool life and process security for production environments The negative rake of 0° (negative) together with a corner radius 1.2 mm supports stable engagement and reduces the likelihood of edge chipping when machining variable batch materials. These geometry choices favour a balanced wear pattern that helps maintain part tolerances across a tool life, which is particularly valuable in serial manufacturing. The grade WPP20G is a Walter-developed cutting material optimised for common Stahl machining tasks, providing a predictable compromise between resistance to abrasion and resistance to fracture. This predictability enables process engineers to plan tool-change intervals and scrap rates with greater confidence. Easy specification and integration into standard toolholders The ISO designation WNMM100612-HU3 identifies the insert geometry and size for straightforward selection of compatible toolholders and clamping systems. As an indexable insert in the Tiger·tec Gold series, it is suited to applications that demand both repeatable performance and efficient production throughput. The insert’s general-purpose character makes it a practical choice for job shops and production lines where flexibility across a range of Stahl grades is required. Specification engineers will welcome the clear geometry and grade information, which streamlines tool lists and reduces the time spent on trial cuts. Contact Metav Werkzeuge today for application guidance, sample availability and advice on integrating the WNMM100612-HU3 WPP20G insert into your tool inventory. Technical Data Article number: WNMM100612-HU3-WPP20G-WALTER Designation: WNMM100612-HU3 WPP20G Type: Drehwendeschneidplatte / indexable turning insert Brand: Walter Tools Series: Tiger-tec Gold Grade: WPP20G Execution: M Tolerance class: M ISO designation without grade: WNMM100612-HU3 Core specifications Insert form: Trigon 80° Corner radius: 1.2 mm Rake angle: 0° (negative) Insert size: 10 Plate thickness: 06 Special features Coating: Tiger·tec Gold Chipbreaker: HU3 Material application: Stahl (P) Substrate: coated carbide FAQ What materials is this insert suitable for? The insert is designed primarily for Stahl (P) applications; the WPP20G grade and chipbreaker HU3 are optimised for turning various unalloyed and alloyed Stahl groups. How does the Tiger·tec Gold coating benefit production? Tiger·tec Gold on the WNMM100612-HU3 WPP20G provides enhanced wear resistance and surface stability, which helps extend tool life and maintain consistent part quality in continuous machining. What advantage does the Trigon 80° geometry provide? The Trigon 80° form gives a strong cutting edge and good load-bearing capability, making the insert suitable for robust turning tasks and operations with interrupted cuts. Is the insert compatible with standard ISO toolholders? Yes, the ISO designation WNMM100612-HU3 enables selection of compatible standard toolholders that accept Trigon 80° inserts with this size and thickness. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners and are mentioned here for clarification only. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
WNMM100616-HU3 WPP10G Wendeplatten - Walter Tools
Take advantage of a premium Tiger‑tec Gold grade that combines wear resistance and consistent edge life with the secure Trigon 80° geometry and an HU3 chipbreaker to maintain productivity in Stahl turning operations. Order directly via Metav Werkzeuge or contact our consultants for application advice. WNMM100616-HU3 WPP10G Trigon 80° turning insert – Tiger‑tec Gold (Stahl) by Walter Tools A WNMM100616-HU3 WPP10G trigon turning insert engineered for productive Stahl machining, featuring a 0° negative rake and HU3 chipbreaker for controlled chip formation. Tiger‑tec Gold coated carbide grade WPP10G Trigon 80° form for secure clamping HU3 chipbreaker for medium/heavy cuts 0° negative rake for stable cutting Increased throughput for Stahl turning with predictable results This insert is designed to raise machining throughput by combining a coated carbide grade with a geometry optimised for repeatable performance. The WPP10G grade, part of the Tiger‑tec Gold series, is tailored to the thermal and chip-formation characteristics of Stahl; this means longer usable life under typical turning conditions and fewer tool changes. The Trigon 80° shape improves clamping stability, which translates into consistent surface finish and fewer interrupted cycles, supporting a smoother production flow. Consistent edge life and controlled chip formation The HU3 chipbreaker offers balanced chip control for medium to heavy cuts, reducing the risk of long, stringy chips and improving evacuation. A 0° negative rake provides a robust cutting edge that resists chipping under intermittent cuts, while the modest corner radius supports both strength and acceptable surface quality. These combined features reduce downtime and contribute to overall process economy by lowering the frequency of insert replacements. Practical geometry and integration into existing toolholders The Trigon 80° plate form is widely compatible with indexable turning toolholders, simplifying retrofitting into existing toolsets. The insert’s dimensions and tolerance class M ensure predictable seating and repeatability from index to index. Clear, standardised geometry reduces setup time and helps maintain concentricity and runout tolerances on the lathe, which in turn improves both dimensional accuracy and surface integrity of machined components. Technical clarity for informed process decisions Key terms explained: a chipbreaker is a relief feature that breaks and directs chips away from the cutting zone; a negative rake increases edge robustness for tough engagement conditions; coated carbide refers to a cemented carbide substrate with a wear-resistant surface layer, enhancing heat resistance and reducing flank wear. These specifics make the insert suitable for general Stahl turning applications where reliability and repeatable performance are required. For tailored advice on integrating this Walter Tools insert into specific turning operations, contact Metav Werkzeuge for technical consultation and order support via e‑mail or phone. Technical data Article number: WNMM100616-HU3-WPP10G-WALTER Designation: WNMM100616-HU3 WPP10G Label: Drehwendeschneidplatte WNMM100616-HU3 WPP10G Walter Tools Manufacturer: Walter Tools Core measurements Corner radius: 1.6 Plate size: 10 Plate thickness: 06 Free rake: 0° (negativ) Plate form: Trigon 80° Special features Series: Tiger‑tec Gold Grade: WPP10G (coated carbide) Chipbreaker: HU3 Material application: Stahl Tolerance class: M Execution: M FAQ What materials is this insert intended for? The WNMM100616-HU3 WPP10G insert is designed primarily for machining Stahl, with the Tiger‑tec Gold grade optimised for the heat and chip-formation behaviour typical of steel. How does the HU3 chipbreaker affect chip control? The HU3 chipbreaker promotes controlled chip segmentation during medium to heavy cuts, improving evacuation and reducing the chance of damaging long chips during turning operations with the Walter Tools insert. Is the Trigon 80° form compatible with standard toolholders? Yes, the Trigon 80° geometry of this turning insert is compatible with commonly used indexable turning toolholders, simplifying replacement and setup in many tooling systems. What advantage does the 0° negative rake offer in practice? A 0° negative rake increases cutting-edge strength and resistance to chipping under interrupted or heavy engagement conditions, providing more robust performance in demanding Stahl turning tasks. How does the Tiger‑tec Gold grade influence tool life? The Tiger‑tec Gold coating on the WPP10G grade enhances heat resistance and wear protection, resulting in more consistent edge life and fewer tool changes across typical Stahl turning applications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter Tools is part of a global portfolio of precision cutting solutions. Protected trademarks and product names belong to their respective owners. Brand names and trademarks are cited solely for explanation; there is no affiliation between our company and the mentioned brands. The offered item is an original, factory-new product of the manufacturer.
WNMM100616-HU3 WPP20G WPP20G Wendeplatten - Walter Tools
Benefit from the combination of high process reliability, optimised chip control and extended tool life thanks to the Tiger·tec Gold grade and HU3 chipbreaker; order the insert directly via Metav Werkzeuge or ask the consultants for application advice. WNMM100616-HU3 WPP20G — indexable turning insert, Trigon 80°, Tiger·tec Gold (Walter Tools) A robust indexable turning insert, the WNMM100616-HU3 WPP20G is designed for high-productivity Stahl turning in industrial machining. Tiger·tec Gold coated for longer tool life Optimised HU3 chipbreaker for stable chips Trigon 80° form for versatile turning Productivity and wear resistance from advanced coating The Walter grade WPP20G, based on Tiger·tec Gold coating technology, combines wear resistance with consistent cutting performance when machining Stahl. This coating architecture reduces flank wear and extends resharpening intervals, resulting in fewer tool changes and higher uptime on the shop floor. For production environments where cycle time and reproducibility matter, the insert’s combination of coating and substrate yields a measurable increase in productive cutting time without sacrificing surface quality. The HU3 chipbreaker supports reliable chip formation under typical Stahl cutting conditions, improving process stability. Geometry tailored for versatile turning operations The Trigon 80° plate form with a 1.6 mm corner radius and 0° (negative) rake angle provides a balance between strength and form accuracy. The trigon profile offers three effective cutting edges per indexable insert, while the slightly larger corner radius contributes to improved edge strength for interrupted cuts and heavier feed passes. The negative rake improves robustness and reduces cutting-edge chipping when machining tougher batches of Stahl; at the same time, the HU3 chipbreaking geometry helps control chip flow for both semi-finish and roughing tasks. This geometry is ideal where repeatable part accuracy and secure clamping are required. Practical handling, compatibility and application scope Supplied in a compact format (size 10, thickness code 06) and manufactured to tolerance class M, the insert fits standard toolholders designed for trigon inserts and suits a broad range of turning tasks in general engineering and production workshops. The grade is specified for the ISO P group, i.e. Stahl, offering a balance of toughness and wear resistance for unalloyed and alloyed steels. The combination of reliable chip control, robust cutting edge and an established coating system helps simplify tool inventory and decision-making in multi-shift operations. For further technical clarification or application-specific recommendations, technical data and cutting-parameter guidance are available on request. Contact Metav Werkzeuge today to discuss how the WNMM100616-HU3 WPP20G insert can be integrated into current machining setups and to request tailored cutting data Technical data SKU: WNMM100616-HU3-WPP20G-WALTER ISO designation: WNMM100616-HU3 WPP20G Manufacturer: Walter Tools Product type: Indexable turning insert (Trigon 80°) Numbers / Core technical data Corner radius: 1.6 mm Rake angle: 0° (negative) Insert size: 10 Thickness code: 06 Tolerance class: M Designs / Special features Coating/grade: Tiger·tec Gold / WPP20G Chipbreaker: HU3 Plate form: Trigon 80° Material application: suitable for Stahl (ISO group P) Execution: M FAQ What materials is this insert intended for? The WNMM100616-HU3 WPP20G is specified for the ISO P group and is designed for machining Stahl, combining toughness and wear resistance for a wide range of steel grades. How does the Tiger·tec Gold grade affect tool life? The Tiger·tec Gold coating of the WPP20G grade improves wear resistance and thermal stability, which extends service intervals and supports consistent performance during longer production runs. Which chipbreaker is fitted and what is its benefit? The HU3 chipbreaker offers controlled chip formation for common turning feeds and depths in Stahl, reducing the risk of entangling chips and improving process reliability. Is the insert suitable for interrupted cuts or heavier feeds? Yes; the Trigon 80° geometry with a 1.6 mm corner radius and a negative rake provides increased edge strength, making the insert suitable for interrupted cuts and more demanding feed conditions. What tolerance and fit can be expected? The insert is manufactured to tolerance class M and is compatible with holders for trigon indexable inserts, ensuring repeatable seating and secure clamping. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered marks are mentioned solely for explanatory purposes; there is no affiliation between our company and the named brands. The offered article is original, factory-new merchandise of the respective manufacturer.
WOEX030204-E57 WKP35S Wendeplatten - Walter Tools
High wear resistance and consistent chip control from the Tiger·tec Silver coating and WKP35S grade ensure extended tool life and reliable surface finish; combined with the Trigon 80° geometry, this insert supports efficient machining of steel and cast iron. Order the WOEX030204-E57 WKP35S directly via Metav Werkzeuge or consult our technical advisers for application-specific guidance. WOEX030204-E57 WKP35S — drilling/boring indexable insert, Tiger·tec Silver, Trigon 80° | Walter Tools The WOEX030204-E57 WKP35S is a Trigon 80° indexable insert for drilling and boring operations, designed and graded for productive machining in steel and cast iron applications. Tiger·tec Silver coated carbide grade WKP35S Trigon 80° geometry for stable chip control Corner radius 0.4 mm for controlled engagement Suitable for steel and cast iron machining Increased productivity through advanced coating and grade The combination of the Tiger·tec Silver series and the WKP35S grade provides a coated carbide substrate engineered for high abrasive resistance and edge stability. This results in fewer tool changes and a more predictable wear pattern during batch production. The cutting material is optimised for the thermal and mechanical conditions encountered when machining steel and cast iron, which helps maintain dimensional consistency and reduces downtime caused by premature flank wear. The insert's construction supports steady performance across varied workpiece batches, contributing to improved uptime and process stability. Geometry and chip control for consistent surface quality The Trigon 80° shape, together with the chipbreaker E57 and a corner radius of 0.4 mm, is designed to balance cutting forces and chip formation. The trigonal form provides robust cutting edges and an advantageous approach angle for bore-entry, while the chipbreaker channels chips away from the cutting zone to reduce re-cutting and improve surface finish. These geometric features lead to stable cutting behaviour and predictability when engaging interrupted or continuous cuts, which in turn contributes to reduced vibration and better workpiece integrity. Practical integration and process benefits Specified with a plate size code of 03 and plate thickness code 02, and manufactured to tolerance class E, this insert is compatible with holders and tool systems accepting the WOEX030204-E57 family. The execution marking X indicates the particular variant within Walter Tools' portfolio. By selecting this insert, shops can expect improved tool life and reproducible results in standard production setups; for non-standard geometries or specialised operations, technical parameter optimisation is recommended to fully exploit the Tiger·tec Silver coating advantages. The design supports cost-effective machining by emphasising repeatability and straightforward tool management in production environments. Contact Metav Werkzeuge for tailored cutting data and holder recommendations for this Walter Tools insert, and arrange expert advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: WOEX030204-E57-WKP35S-WALTER Name: Bohr-/Aufbohrwendeschneidplatte WOEX030204-E57 WKP35S Manufacturer: Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte Numbers / Core technical data Corner radius: 0.4 mm Plate size: 03 Plate thickness: 02 Geometry angle: Trigon 80° Tolerance class: E Special features / Versions Coating / series: Tiger·tec Silver Grade: WKP35S (coated carbide) Chipbreaker: E57 Applicable for: Steel (P) and Cast iron (K) Execution: X Shape: Trigon 80° FAQ Which materials is this insert suitable for? The WOEX030204-E57 WKP35S insert from Walter Tools is intended for machining steel and cast iron (ISO groups P and K), reflecting the grade and coating design. What advantages does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating enhances abrasive wear resistance and edge security on the WKP35S grade, improving life span under the thermal loads typical for steel and cast iron cutting. How does the Trigon 80° shape affect machining performance? The Trigon 80° geometry offers a robust cutting edge and an effective entry angle for bore operations, promoting stability and consistent chip evacuation when paired with an appropriate chipbreaker. What role does the chipbreaker E57 play? The E57 chipbreaker is designed to control chip formation and evacuation, reducing the risk of re-cutting and aiding surface finish consistency during drilling and boring. What does tolerance class E mean for tool replacement? Tolerance class E denotes the manufacturing tolerance applied to the insert, which supports repeatable seating and interchangeability within compatible toolholder systems. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WOEX030204-E57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold PVD coating, a Trigon 80° geometry and the versatile WSP45G grade for reliable drilling and boring in a wide range of materials; buy directly via Metav Werkzeuge or request tailored application advice from the consultants. WOEX030204-E57 WSP45G — Drill/Boring indexable insert, Tiger·tec Gold (Walter Tools) The WOEX030204-E57 WSP45G is a Trigon 80° indexable insert from Walter Tools, engineered for drilling and boring operations in steel, stainless steel and heat‑resistant alloys and optimised for stable chip formation and long edge life. Tiger·tec Gold coated carbide for high durability Trigon 80° form with 0.4 mm corner radius Suitable for steel, stainless steel and superalloys Durable coated grade for extended service life The insert’s Tiger·tec Gold PVD coating on a coated carbide substrate provides improved resistance to abrasive wear and thermal loading, which translates into longer tool life and fewer tool changes. PVD coatings form a thin, hard layer that reduces adhesion and heat transfer to the cutting edge; in practice this means more consistent performance during continuous drilling and boring cycles and lower life‑cycle costs through reduced downtime. Geometry and chip control that improve process stability The Trigon 80° form combined with the E57 chipbreaker and a 0.4 mm corner radius promotes predictable chip formation and evacuation in through‑hole and bored passages. A stable cutting edge and optimised chipbreaker reduce the risk of built‑up edge on stainless and difficult‑to‑machine alloys, leading to a more reliable surface finish and fewer rejected parts. The tolerance class E ensures consistent seating and repeatable orientation in suitable toolholders. Broad material applicability to simplify inventory Designed as a versatile PVD grade, WSP45G covers the ISO groups P / M / S, i.e. unalloyed and alloyed steel (P), stainless steel (M) and heat‑resistant superalloys/titanium (S). Choosing this single grade for mixed production runs reduces the need for multiple dedicated inserts and simplifies tool management while maintaining process robustness across diverse workpiece materials. Practical handling and integration guidance The insert size 03 and thickness 02 suit many compact drilling and boring toolholders; the Trigon shape provides strong cutting edges for interrupted cuts. For best results, ensure correct clamping torque and clean seating in the pocket, monitor edge wear and replace inserts once flank wear or chipping exceeds acceptable limits. For material‑specific cutting data or tailored recommendations for different holders and operations, consult the technical advisors – their input supports secure chip control and cost‑effective machining. Contact Metav Werkzeuge for application guidance, material‑specific cutting data and tailored quotations for the WOEX030204-E57 WSP45G indexable insert from Walter Tools Technical Data SKU: WOEX030204-E57-WSP45G-WALTER Product type: Bohr-/Aufbohrwendeschneidplatte Series: Tiger-tec Gold Grade: WSP45G Manufacturer: Walter Tools Core specifications Insert size: 03 Insert thickness: 02 Geometry: Trigon 80° Corner radius: 0.4 mm Tolerance class: E Special features Material: coated carbide (PVD) Chipbreaker: E57 Execution: X Suitable for: Steel (P), Stainless steel (M), Superalloys/Titanium (S) Application: drilling and boring indexable operations FAQ What materials can this insert machine effectively? The WOEX030204-E57 WSP45G is suitable for steel (P), stainless steel (M) and superalloys/titanium (S), offering a single‑grade solution for mixed material production. Which geometry and chipbreaker are specified for improved chip control? This indexable insert uses a Trigon 80° geometry with the E57 chipbreaker to promote stable chip formation and evacuation in through‑hole and bored operations. How does the Tiger·tec Gold coating benefit cutting performance? The Tiger·tec Gold PVD coating increases wear resistance and reduces adhesion at the cutting edge, resulting in longer edge life and improved process reliability during extended cycles. What does the corner radius mean for surface finish? A 0.4 mm corner radius provides a balance between edge strength and surface finish: it helps protect the edge under intermittent cutting while still delivering acceptable surface quality for many drilling and boring applications. Is this insert compatible with standard drilling toolholders? The insert’s 03 size and 02 thickness are intended for compact drilling and boring holders; correct seating and clamping are essential for repeatable performance and secure cutting. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WOEX040304-E57 WKP25S Wendeplatten - Walter Tools
Combine the proven wear resistance of the Tiger·tec Silver coating with the Trigon 80° geometry and a 0.4 mm corner radius for stable chip formation and consistent edge life; order the WOEX040304-E57 WKP25S drill/counterbore indexable insert directly via Metav Werkzeuge or consult our specialists for application advice. WOEX040304-E57 WKP25S drill/counterbore indexable insert, Tiger·tec Silver, Walter Tools The WOEX040304-E57 WKP25S is an indexable insert engineered for drilling and counterboring operations, optimised for use in steel and cast iron applications. Tiger·tec Silver coating for high wear resistance Trigon 80° geometry for stable entry 0.4 mm corner radius for consistent edge strength Suited for steel (P) and cast iron (K) Increase uptime through advanced coating and grade selection The combination of the Tiger·tec Silver coating and the WKP25S grade delivers measurable improvements in tool life and process stability. The specialised coating reduces abrasive wear during prolonged contact with workpiece material, which means fewer index changes and longer uninterrupted production runs. For customers seeking predictable performance, this insert offers improved wear resistance and consistent edge retention, translating into reduced machine downtime and lower tooling consumption per component. Geometry that improves entry behaviour and chip control The Trigon 80° plate form with its optimised clearance angles gives a stable cutting engagement and reduces tendency to pull or chatter on entry. Paired with the chipbreaker E57, the design promotes controlled fragmentation and evacuation of swarf, particularly important when machining interrupted or deeper holes. Improved chip control reduces the risk of recutting and helps maintain surface quality, so machining cycles run more reliably and component tolerances remain reproducible. Suitable for typical steel and cast iron machining tasks Designed according to the recommendations of ISO material groups, this insert is rated for steel (P) and cast iron (K). The grades and geometry address the typical heat generation and chip forms encountered in these materials: steels require management of long, ductile swarf and thermal load, while cast irons demand abrasion resistance and the ability to break short, brittle chips. This insert supports both scenarios, allowing a single indexable solution across mixed production batches and simplifying inventory management. Practical benefits for workshop integration With a compact 04 plate size and a nominal thickness 03, the insert fits common drill and counterbore toolholders that accept this designation, enabling straightforward retrofitting into existing tooling systems. The 0.4 mm corner radius balances toughness and cutting precision for repeated operations, enhancing reliability and repeatability in series production. Overall, the design reduces the number of insert variants required, supporting leaner tooling stocks and faster set-up times. Contact Metav Werkzeuge for application guidance and availability of the WOEX040304-E57 WKP25S with Tiger·tec Silver coating Technical data SKU: WOEX040304-E57-WKP25S-WALTER Article: Bohr-/Aufbohrwendeschneidplatte WOEX040304-E57 WKP25S Walter Tools Series: Tiger·tec Silver Grade: WKP25S Facts Corner radius: 0.4 mm Plate form: Trigon 80° Plate size: 04 Plate thickness: 03 Chipbreaker: E57 Tolerance class: E Special features Coating: Tiger·tec Silver (coated carbide technology) Material application: Steel (P), Cast iron (K) Plate designation: WOEX040304-E57 Shape: Trigon 80° insert for drilling/counterboring FAQ What materials is this insert suitable for? The WOEX040304-E57 WKP25S is specified for steel (P) and cast iron (K) according to ISO groupings, making it suitable for typical turning and drilling tasks in these materials. How does the Tiger·tec Silver coating benefit machining? The Tiger·tec Silver coating on the WKP25S grade improves abrasion resistance and thermal stability, which extends tool life and provides more consistent machining results over longer cycles. What role does the Trigon 80° form play in performance? The Trigon 80° geometry improves entry stability and load distribution, helping to reduce vibration and support stable chip formation during drilling or counterboring. Is the chipbreaker E57 suitable for interrupted cuts? Yes, the chipbreaker E57 is designed to promote reliable chip fragmentation and evacuation, which is advantageous in interrupted cuts and when working with materials that produce short or segmented chips. Can this insert be used in existing toolholders with standard insert seats? The insert follows standard designation dimensions (size 04, thickness 03, Trigon 80°), so it is compatible with toolholders designed for this insert family; verify holder compatibility before use. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only; there is no affiliation between our company and the named manufacturers. The offered article is an original, brand-new product from Walter Tools.
WOEX040304-E57 WKP35S Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver coating and the WKP35S grade for extended tool life and consistent chip control in steel and cast iron machining; the Trigon 80° geometry with a 0.4 mm corner radius further stabilises cutting performance. Order directly via Metav Werkzeuge or request tailored advice from our technical consultants. WOEX040304-E57 WKP35S Trigon 80° indexable insert — Walter Tools, Tiger·tec Silver A WOEX040304-E57 WKP35S drilling and reaming indexable insert engineered for productive machining of steel and cast iron with a Trigon 80° geometry and Tiger·tec Silver coating. Tiger·tec Silver coating for long tool life WKP35S coated carbide grade Trigon 80° geometry for stable cuts 0.4 mm corner radius for edge strength Greater efficiency through advanced coating technology The Tiger·tec Silver coating combines a wear-resistant surface with thermal stability, which reduces flank wear and preserves the cutting edge during continuous operation. This results in fewer index changes and less downtime, supporting a higher parts-per-shift output. For jobs dominated by heat generation, such as turning and drilling in P-group steels, the coated grade provides reliable performance and predictable tool life, improving process economy and planning. Consistent performance for steel and cast iron applications Designed for ISO groups P (steel) and K (cast iron), the grade WKP35S is tuned to the typical chip formation and abrasive conditions encountered with these materials. The chipbreaker E57 promotes controlled chip flow, reducing the risk of built-up edge and improving surface finish on the workpiece. By matching grade chemistry and coating to the material group, the insert helps maintain consistent component quality across batch production and mixed-series runs. Geometry that stabilises the machining process The Trigon 80° form and a 0.4 mm corner radius combine to increase insert rigidity and distribute cutting forces more evenly, which lowers vibration and improves hole quality in drilling or reaming operations. A modest corner radius supports stronger edges without compromising entry behaviour, making the insert a practical choice for interrupted cuts or less rigid setups. The trigon geometry also offers three cutting corners per insert, optimising economy per indexable element. Practical compatibility and handling guidance This insert is supplied in the WOEX format (designation WOEX040304-E57) with size 04 and thickness 03, tolerance class E and execution X, suitable for toolholders configured for drilling and bore-enlargement applications. The combination of coated carbide and the E57 chipbreaker provides a good balance between cutting-edge protection and chip control. For optimal results, select feed and speed values aligned with the component material and machine rigidity; for specific holder compatibility or process windows, consult the technical advisers at Metav Werkzeuge. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger·tec Silver inserts and to discuss optimal machining parameters for your application, call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: WOEX040304-E57-WKP35S-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WOEX040304-E57 WKP35S Walter Tools Series: Tiger-tec Silver Grade: WKP35S Manufacturer: Walter Tools Designation: WOEX040304-E57 Product type: Drilling/reaming indexable insert Facts Plate size: 04 Plate thickness: 03 Corner radius: 0.4 mm Chipbreaker: E57 Tolerance class: E Special features Coating: Tiger·tec Silver (coated carbide) Geometry: Trigon 80° Material suitability: Steel (P) and Cast iron (K) Execution: X Series and grade information included in designation FAQ What materials is this insert suitable for? The WOEX040304-E57 WKP35S insert from Walter Tools is suitable for machining steel (P) and cast iron (K) according to ISO material groupings, offering tailored chip control for both material families. What does the E57 chipbreaker provide? The E57 chipbreaker on the WKP35S grade promotes controlled chip formation and evacuation, which helps to maintain surface finish and reduce the likelihood of built-up edge during continuous drilling or reaming. How does the Trigon 80° geometry benefit drilling operations? Trigon 80° geometry increases edge strength and rigidity, improving stability in drilling or bore-enlargement tasks; the 0.4 mm corner radius further supports edge durability under moderate engagement. Is the WKP35S grade coated or uncoated? The WKP35S is a coated carbide grade within the Tiger·tec Silver technology, combining a wear-resistant surface with thermal robustness for demanding P- and K-group applications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand presentation: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking. Protected trademarks and trade names are the property of their respective owners and are mentioned here for explanation only. There is no affiliation between our company and the named brands. The offered item is original, brand-new merchandise from the manufacturer.
WOEX040304-E57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WSP45G grade for extended tool life and reliable chip control; the Trigon 80° form and 0.4 mm corner radius increase stability in drilling and boring operations. Order the insert directly via Metav Werkzeuge or consult the technical team for application matching. WOEX040304-E57 WSP45G Trigon 80° indexable insert – Walter Tools The WOEX040304-E57 WSP45G is an indexable trigon insert designed for drilling and boring applications, offering a coated carbide grade optimised for steel, stainless steel and heat‑resistant alloys Tiger·tec Gold coating for long tool life Versatile for steel, stainless and superalloys Trigon 80° form for stable cutting forces Greater process stability through geometry and tolerances The trigon 80° geometry delivers a broad support area that reduces cutting edge deflection and maintains axial stability during deep drilling and boring cycles. Combined with tolerance class E, the insert conforms to consistent dimensional limits that support repeatable set‑ups and predictable runout, which reduces rework. The E57 chipbreaker aids controlled chip formation, reducing the risk of clogging and enabling safer evacuation of swarf in interrupted cuts. This results in fewer tool changes and more consistent component quality in serial production. Longer tool life and adaptable performance from the coating and grade Equipped with Tiger·tec Gold technology and the WSP45G PVD‑coated carbide grade, the insert resists abrasive wear and preserves a stable cutting edge under elevated thermal loads. The grade is formulated for the P/M/S material groups — steel (P), stainless steel (M) and superalloys/titanium (S) — so the same insert can be applied across multiple workpiece families, simplifying tool inventory. The coated substrate reduces flank and crater wear, which translates into extended edge life and fewer unscheduled tool changes for machining centres and drilling stations. Practical advantages that improve shopfloor throughput Compact dimensions (size 04, thickness 03) and the 0.4 mm corner radius combine to offer a balance between edge strength and cutting agility: the radius supports a robust tip for heavier feeds while remaining suitable for finishing passes where surface quality matters. The insert’s trigon form and coated grade support a wide range of drilling and boring feeds, making it useful for both roughing and semi‑finishing cycles. By standardising on a proven insert geometry and a versatile coating system, workshops gain steady productivity, predictable tool life and simplified process planning. Contact Metav Werkzeuge for application advice and rapid supply of this Walter Tools insert — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: WOEX040304-E57-WSP45G-WALTER Type: Bohr-/Aufbohrwendeschneidplatte (indexable insert for drilling/boring) Designation: WOEX040304-E57 Series: Tiger·tec Gold Grade: WSP45G Manufacturer: Walter Tools Core specifications Shape: Trigon 80° Size: 04 Thickness: 03 Corner radius: 0.4 mm Tolerance class: E Chipbreaker: E57 Execution: X Applications & special features Suitable for: Steel (P), Stainless steel (M), Superalloys/Titanium (S) Coated carbide grade for enhanced wear resistance Versatile for drilling and boring operations Stable cutting edge and reliable chip control FAQ Which materials can be machined with this insert? The WOEX040304-E57 WSP45G insert is formulated for the ISO material groups P, M and S — that is, steel, stainless steel and heat‑resistant superalloys or titanium. What benefit does the Tiger·tec Gold coating provide? Tiger·tec Gold on the WSP45G grade improves thermal resistance and reduces abrasive wear, extending the insert life and maintaining cutting edge stability under elevated temperatures. How does the Trigon 80° form affect machining? The Trigon 80° geometry increases axial support and reduces deflection during drilling and boring, promoting stable cutting conditions and repeatable hole quality. What does the 0.4 mm corner radius mean for performance? A 0.4 mm corner radius balances edge robustness and surface finish: it increases tip strength for higher feeds while still allowing controlled finishing passes where required. What is indicated by tolerance class E for this insert? Tolerance class E denotes a defined dimensional tolerance level that supports accurate positioning and consistent clamping, which is advantageous for serial production and high‑precision assemblies. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WOEX05T304-E57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WKP25S carbide grade and precise Trigon 80° geometry for reliable drilling and spot-boring performance; order the insert via Metav Werkzeuge or consult our advisors for application guidance. WOEX05T304-E57 WKP25S drilling/spot-boring insert — Trigon 80°, 0.4 mm radius (Walter Tools) The WOEX05T304-E57 WKP25S is a Trigon 80° drilling and spot-boring insert engineered for high-process reliability when machining steel and cast iron. Tiger·tec Silver coated carbide grade WKP25S Optimised for steel and cast iron machining Trigon 80° form with 0.4 mm corner radius Suitable for drilling and spot-boring operations Consistent cutting performance through advanced coating and grade The combination of the Tiger·tec Silver coating and the WKP25S coated carbide grade provides a balance of wear resistance and thermal stability that supports prolonged cutting intervals. This engineered surface reduces adhesive wear on edges and helps maintain dimensional accuracy during cyclic drilling tasks. For production environments where repeatability matters, the coated substrate contributes to fewer regrinds and more consistent component tolerances. Geometry tailored to reliable entry and chip control The Trigon 80° form with a 0.4 mm corner radius offers a robust cutting edge for the demands of drilling and spot-boring; the geometry promotes stable entry, controlled cutting forces and reduced vibration. The insert thickness T3 and the trigon profile help to distribute cutting loads evenly, which extends edge life and mitigates the risk of premature chipping in interrupted cuts. These design choices translate into lower scrap rates and more predictable cycle times. Chip management and material adaptability to shorten setup time Equipped with the E57 chipbreaker and designed for ISO groups P and K, this insert improves chip formation for both steel and cast iron, reducing the need for complex coolant strategies or special fixtures. Better chip control reduces the likelihood of recutting and facilitates higher feed rates where the machine and holder permit. For workshops aiming to streamline setups, this versatility limits tool changes and shortens overall process preparation. Productivity gains through stable tool life and predictable results Integrating an insert with a stable grade and a proven coating technology supports higher uptime and consistent surface results. The robust edge geometry and the Tiger·tec Silver technology combine to deliver repeatable performance across series production, making the component well suited to batch and single-piece workflows where quality and throughput matter. Choosing a matched insert grade reduces trial-and-error and helps to standardise machining parameters across similar jobs. Contact Metav Werkzeuge for tailored machining recommendations, availability and to discuss integration of the WOEX05T304-E57 WKP25S into existing processes (+49 2822 7131930 or info@metav-werkzeuge.com) Technical data SKU: WOEX05T304-E57-WKP25S-WALTER Article number: WOEX05T304-E57 Designation: WOEX05T304-E57 WKP25S Facts Corner radius: 0.4 mm Insert form: Trigon 80° Insert size: 05 Plate thickness: T3 Tolerance class: E Special features Grade: WKP25S (Tiger·tec Silver coated carbide) Chipbreaker: E57 Series: Tiger·tec Silver Material adaptation: P (steel), K (cast iron) Application: drilling and spot-boring FAQ What materials is this insert suitable for? The WOEX05T304-E57 WKP25S is specified for ISO groups P and K, meaning it is suited for machining steel and cast iron. Which chipbreaker is fitted and what benefit does it provide? The insert uses the E57 chipbreaker, designed to improve chip control during drilling and spot-boring operations, reducing the risk of recutting. What does the Trigon 80° form mean for machining? A Trigon 80° form provides a robust edge and stable cutting geometry, supporting reliable entry and even load distribution in drilling tasks. How does the Tiger·tec Silver coating affect tool life? The Tiger·tec Silver coating increases thermal and abrasive resistance, which helps to extend cutting intervals and preserve edge integrity under typical steel and cast iron cutting conditions. Manufacturer/Responsible: Walter Tools / AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden; support.coromant@sandvik.com The Walter AG (brand appearance: Walter Tools) is a recognised global provider of precision tools for metalworking and forms part of the Sandvik Group. Protected trademarks and trade names belong to their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only; there is no affiliation between our company and the named brands. The offered article is original and factory-new.
WOEX05T304-E57 WKP35S WKP35S Wendeplatten - Walter Tools
Benefit from a combination of wear resistance, stable chip control and suitability for both steel and cast iron machining — the insert supports consistent cycle times and predictable tool changes. Order the insert via Metav Werkzeuge or contact the consultants for tailored machining advice. WOEX05T304-E57 WKP35S — Bohr-/Aufbohrwendeschneidplatte by Walter Tools, for steel and cast iron A precision indexable insert designed for drilling and boring applications, combining the Tiger·tec Silver technology with the WKP35S grade to deliver durable edge life and consistent chip formation. WOEX05T304-E57 WKP35S by Walter Tools Tiger·tec Silver coating for improved wear Trigon 80° form, 0.4 mm corner radius For steel (P) and cast iron (K) applications Longer tool life through advanced coating technology The combination of the WKP35S grade and Tiger·tec Silver coating gives this indexable insert a higher resistance to abrasive and adhesive wear compared with uncoated grades. The coated carbide formulation is adapted to the temperature and chip-flow behaviour typical for machining steel and cast iron, which reduces flank wear and extends reliable cutting time. From a production-planning perspective, this stability translates into fewer unscheduled tool changes and more predictable batch processing. Consistent chip control and robust geometry for drilling and boring The E57 chipbreaker and the Trigon 80° plate form are configured to support repeatable chip splitting and evacuation during axial cutting actions. The modest 0.4 mm corner radius and T3 thickness ensure a balance between edge strength and dimensional access in bores, helping to maintain surface quality while avoiding excessive cutting forces. In practice, this means improved hole integrity and steadier feed control during both plunge and extended boring sequences. Optimised for ISO P and K material groups Designed and specified for ISO groups P (steel) and K (cast iron), this insert addresses the characteristic thermal and mechanical demands of these materials. The grade’s composition and coating strategy favour stable chip formation for steels and resist the abrasive tendencies of grey or nodular cast irons. For workshop engineers and process planners, this yields a dependable choice when standardising tool inventories for mixed-production runs. Contact Metav Werkzeuge for availability of the WOEX05T304-E57 WKP35S by Walter Tools, request a process recommendation for specific materials, or obtain delivery and stock information via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: WOEX05T304-E57-WKP35S-WALTER Designation: WOEX05T304-E57 WKP35S Product type: Bohr-/Aufbohrwendeschneidplatte Manufacturer: Walter Tools Grade: WKP35S Series: Tiger·tec Silver Measures & numbers Plate size: 05 Plate form: Trigon 80° Corner radius: 0.4 mm Thickness: T3 Chipbreaker: E57 Tolerance class: E Design & features Coating: Tiger·tec Silver (coated carbide) Material compatibility: P (steel), K (cast iron) Execution: X Plate designation without grade: WOEX05T304-E57 FAQ What applications is this insert designed for? The WOEX05T304-E57 WKP35S insert by Walter Tools is designed for drilling and boring tasks, optimised for machining steel (ISO P) and cast iron (ISO K) materials. How does the Tiger·tec Silver technology benefit machining? Tiger·tec Silver in the WKP35S grade improves wear resistance and thermal stability, helping the insert maintain its cutting edge longer under typical drilling and boring conditions. What does the E57 chipbreaker provide in practice? The E57 chipbreaker on the WOEX05T304-E57 WKP35S supports controlled chip formation and evacuation, which reduces the risk of chip jams and contributes to consistent hole quality. Is the corner radius suitable for finishing work? The 0.4 mm corner radius balances edge strength and surface finish, making the insert suitable for applications where dimensional accuracy and consistent surface quality are required. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned exclusively for explanation and identification purposes. There is no affiliation between our company and the named manufacturers. The offered item is original, factory-new merchandise from the manufacturer.
WOEX05T304-E57 WSP45G WSP45G Wendeplatten - Walter Tools
Benefit from the combination of the Tiger·tec Gold coating and the WSP45G grade for reliable, long-lived performance in drilling and boring operations; the Trigon 80° geometry and E57 chipbreaker support stable cutting and consistent surface quality. Order or request application guidance directly via Metav Werkzeuge. WOEX05T304-E57 WSP45G Trigon 80° drilling/boring indexable insert by Walter Tools The WOEX05T304-E57 WSP45G is an indexable insert engineered for drilling and boring tasks where process reliability and edge stability are decisive, suitable for machining Stahl, rostfreier Stahl and heat-resistant alloys. Tiger·tec Gold PVD coating Suitable for Stahl, rostfreier Stahl and superalloys Trigon 80° geometry for rigid clamping 0.4 mm corner radius, T3 thickness High-performance cutting for demanding materials The WOEX05T304-E57 WSP45G insert combines the Tiger·tec Gold technology with a specifically developed coated carbide substrate to deliver productive machining across a broad material spectrum. The PVD-based coating increases resistance to adhesive wear and maintains a stable cutting edge, which reduces the frequency of insert changes and keeps cycle times predictable. For metalcutting operations that require repeatable results—such as component families in aerospace, energy or general engineering—this grade targets balance between wear resistance and toughness to withstand thermal and mechanical loads during drilling and boring. Geometry and edge design that stabilise the cut The Trigon 80° shape and the 0.4 mm corner radius provide a robust seating and a durable edge for applications with higher radial forces. The chipbreaker E57 is designed to control chip formation during interrupted cuts and deep-hole entries, improving evacuation and lowering re-cutting risk. A T3 plate thickness contributes to rigidity in the holder, reducing deflection and vibration so that surface finishes remain consistent. Together, these design choices translate into fewer rejects and improved first-pass quality on precision bores. Practical use and compatibility in workshop processes This insert is intended for use where machining of Stahl, rostfreier Stahl and demanding superalloys or titanium alloys is required; the WSP45G grade is versatile enough to address typical heat generation and chip formation behaviours of these materials. For best results, pair the insert with a rigid, correctly aligned toolholder and use cutting parameters adapted to the workpiece alloy and hole depth; the geometry supports both axial engagement and stable clamping. If process optimisation or parameter guidance is needed for specific machines or materials, technical consultation can help align cutting data to production targets and extend tool life. Contact Metav Werkzeuge for tailored application advice and availability of the WOEX05T304-E57 WSP45G insert from Walter Tools — our consultants provide practical setup recommendations and delivery options. Technical data Article number: WOEX05T304-E57-WSP45G-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WOEX05T304-E57 WSP45G Walter Tools Manufacturer: Walter Tools Core specifications Geometry: Trigon 80° Size: 05 Corner radius: 0.4 mm Plate thickness: T3 Chipbreaker: E57 Materials & features Grade: WSP45G (Tiger·tec Gold) Substrate: coated carbide Applicable for: Stahl; rostfreier Stahl; superalloys and titanium Tolerance class: E Execution: X Series: Tiger·tec Gold ISO designation: WOEX05T304-E57 WSP45G FAQ Which materials can this insert machine effectively? The WOEX05T304-E57 WSP45G insert is suited for machining Stahl, rostfreier Stahl and heat-resistant superalloys including titanium; the WSP45G grade balances toughness and wear resistance for these groups. What advantages does the Tiger·tec Gold coating provide? Tiger·tec Gold on the WOEX05T304-E57 WSP45G improves resistance to adhesive wear and thermal loading, helping to maintain a stable cutting edge and extend insert life under demanding drilling conditions. Why is the Trigon 80° shape beneficial for drilling and boring? The Trigon 80° geometry offers a secure seat in the holder and enhanced stiffness, which reduces deflection during axial engagement and supports precision bores with consistent surface quality. How does the E57 chipbreaker affect chip control? The E57 chipbreaker promotes controlled chip formation and breakage during interrupted cuts and deep bores, aiding evacuation and reducing the risk of re-cutting or chip-related tool damage. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation and identification purposes; there is no affiliation or endorsement implied between Metav Werkzeuge GmbH and the trademark owners.
WOEX06T304-E57 WAK15 Wendeplatten - Walter Tools
Benefit from a combination of precise aluminium machining, consistent chip control and economical indexable tooling. The WAK15 uncoated carbide grade and Trigon 80° geometry ensure reliable holemaking in non‑ferrous metals — order the insert directly via Metav Werkzeuge or consult our advisors for application guidance. WOEX06T304-E57 WAK15 – Indexable drilling/boring insert, Trigon 80°, Walter Tools A WOEX06T304-E57 WAK15 indexable plate designed for high‑performance drilling and boring in aluminium and other non‑ferrous metals. Trigon 80° geometry for precision drilling Uncoated carbide grade WAK15 for non‑ferrous metals 0.4 mm corner radius for controlled chip formation Walter N‑series design for consistent process stability Reliable holemaking performance in aluminium The insert’s WAK15 composition is an uncoated carbide grade optimised for aluminium and other non‑ferrous metals. Combined with the Trigon 80° geometry and the E57 chipbreaker, this design reduces material adhesion and improves surface finish in high‑feed drilling or boring operations. The corner radius 0.4 mm helps to distribute cutting forces and supports a predictable wear pattern; this reduces vibration and leads to longer tool life in continuous production. For engineers evaluating tooling options, the result is a measurable improvement in process reliability and a reduction in scrap from poor chip evacuation. Efficient process stability and repeatability for production runs Being part of the Walter N‑series, the insert delivers consistent edge performance and repeatable seating in compatible toolholders. The indexable insert format enables quick indexing and replacement, keeping machine downtime to a minimum and increasing overall productivity. The tolerance class E ensures dimensional accuracy for mandrel and head fitting, which matters in serial production where every hole must meet specification. This combination supports a rational decision: reduced cycle interruptions and stable output under varying batch sizes. Simple integration, clear chip control and workshop benefits The geometry and E57 chipbreaker are designed for controlled chips in soft to medium non‑ferrous alloys, easing disposal and reducing fork lift or swarf handling issues. The insert’s size 06 and T3 thickness make it compatible with a range of drilling and boring heads engineered for trigon‑style inserts; this facilitates retrofitting existing tool systems with minimal adjustment. For less experienced staff, the principles are straightforward: sharper, low‑friction cutting edges yield cleaner holes and fewer reworks, while the insert format simplifies tool management and storage. For precision aluminium holemaking with Walter Tools, contact Metav Werkzeuge to check availability of the WOEX06T304‑E57 WAK15 insert and request tailored advice by phone or email Technical data Article number: WOEX06T304-E57-WAK15-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WOEX06T304-E57 WAK15 Walter Tools Manufacturer: Walter Tools Facts Insert size: 06 Corner radius: 0.4 mm Insert angle: 80° Thickness: T3 Tolerance class: E Special features Grade: WAK15 (uncoated carbide) Series: Walter N‑series Chipbreaker: E57 Geometry: Trigon 80° Application: aluminium and non‑ferrous metals FAQ What materials is this insert suitable for? The WOEX06T304‑E57 WAK15 insert from Walter Tools is intended for aluminium and other non‑ferrous metals, using a geometry and grade optimised to minimise material adhesion. What does the grade WAK15 indicate? WAK15 denotes an uncoated carbide grade developed by Walter for effective machining of non‑ferrous alloys; the grade emphasises sharp cutting edges and low friction in light‑metal applications. How does the Trigon 80° geometry help in boring operations? The Trigon 80° geometry offers stable seating and a robust cutting edge for holemaking, improving positional accuracy and edge life during drilling and boring in soft materials. What is the role of the E57 chipbreaker? The E57 chipbreaker is engineered to break and control chips in aluminium machining, enhancing evacuation and reducing the risk of built‑up edge or clogging in the toolholder. Is this insert compatible with standard toolholders? As part of the Walter N‑series and with an insert size 06 and T3 thickness, the WOEX06T304‑E57 WAK15 fits toolholders designed for trigon 80° indexable inserts; verification with the specific holder catalogue is recommended. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WOEX06T304-E57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WKP25S grade and a Trigon 80° geometry to achieve reliable, repeatable performance in drilling and bore-enlarging operations; order the insert directly via Metav Werkzeuge or request cutting data from the consultants. WOEX06T304-E57 WKP25S drilling/bore-enlarging indexable insert, Tiger·tec Silver by Walter Tools WOEX06T304-E57 WKP25S is an indexable insert for drilling and bore enlargement, optimised for machining steel and cast iron in industrial production environments. Tiger·tec Silver coating for high process reliability Designed for steel and cast iron machining Trigon 80° form with 0.4 mm corner radius Coated carbide grade WKP25S for stable wear Faster, more consistent material removal with advanced coating and grade The combination of the Tiger·tec Silver coating and the WKP25S coated carbide grade delivers a clear, measurable benefit: improved wear resistance under the typical heat and strain encountered when machining steel and cast iron. This results in longer tool life and fewer insert changes, which increases machine uptime and lowers the effective cost per hole. The coating technology is formulated to manage heat and control built-up edge, translating to more consistent cycle times and predictable production planning. Geometry that supports precision and stable chip control The Trigon 80° plate form and its corner radius 0.4 mm are designed to balance cutting-edge strength with favourable chip formation for drilling and bore enlargement applications. The trigon geometry provides a robust cutting edge that resists deflection, while the engineered chipbreaker (E57) promotes short, controllable chips when working with both ferritic steels and grey or ductile cast iron. The result is improved dimensional stability and precision in through-hole and enlargement operations. Robust design for demanding industrial workflows Supplied in the 06 size with T3 plate thickness, this insert is configured for operations where repeatability and mechanical stability are crucial. The insert’s tolerances (class E) and sturdy construction support high feed rates and steady axial loads commonly encountered in production drilling. Integrating this insert into a process strategy yields tangible benefits in productivity and process security, with fewer interruptions for insert changes and reduced scrap rates from variability. Practical benefits for shop-floor decision making Owing to its suitability for the ISO P and K material groups, the insert is a versatile choice across mixed-production environments. The combination of coated carbide and the Tiger·tec Silver series makes the insert a pragmatic option for operations that require a single grade to cover a range of steels and cast irons. Where setup time and tooling complexity are minimised, throughput increases and quality targets are more readily achieved, supporting both small-batch flexibility and larger-volume runs. Contact Metav Werkzeuge for tailored application advice on Walter Tools inserts and request the specific cutting data for WOEX06T304-E57 WKP25S Technical data Article number: WOEX06T304-E57-WKP25S-WALTER Designation: WOEX06T304-E57 WKP25S Type: drilling/bore-enlarging indexable insert Series: Tiger·tec Silver Grade: WKP25S Manufacturer: Walter Tools Facts Plate form: Trigon 80° Plate size: 06 Thickness: T3 Corner radius: 0.4 mm Chipbreaker: E57 Tolerance class: E Special features Coating: Tiger·tec Silver Material applicability: P / K (steel and cast iron) Application: drilling and bore enlarging Execution: X Plate designation without grade: WOEX06T304-E57 FAQ Which materials are suitable for this insert? The WOEX06T304-E57 WKP25S is specified for ISO groups P and K, meaning it is suitable for steel (P) and cast iron (K) machining. What does the Tiger·tec Silver coating improve? The Tiger·tec Silver coating on the WKP25S grade improves thermal management and wear resistance, enabling more consistent performance and longer tool life in demanding drilling operations. How does the Trigon 80° form affect machining? The Trigon 80° form provides a robust cutting edge with good resistance to deflection, supporting precision and stable chip control during bore enlargement and drilling. What is the significance of the E57 chipbreaker? The E57 chipbreaker is engineered to produce short, controllable chips when machining steels and cast irons, reducing the risk of tool interference and improving surface quality. Can this insert be used at higher feed rates? With its T3 thickness and tolerance class E, the insert is built for mechanical stability under substantial axial loads, permitting higher feed rates where toolholder and machine rigidity allow. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (marketed as Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, factory-new product from the manufacturer.
WOEX06T304-E57 WKP35S Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Silver grade and the WKP35S cutting material for reliable machining of steel and cast iron, combined with a compact trigon geometry that improves tool life and repeatability. Order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. WOEX06T304-E57 WKP35S drill/boring indexable insert by Walter Tools — Trigon 80° with E57 chipbreaker WOEX06T304-E57 WKP35S is an indexable insert designed for drilling and bore‑enlargement applications in industrial machining, optimised for steel and cast iron workpieces Tiger‑tec Silver coated for extended life Suitable for steel (P) and cast iron (K) Trigon 80° form for stable engagement Corner radius 0.4 mm for repeatable edges Consistent cutting performance for steel and cast iron The combination of the WKP35S grade and Tiger‑tec Silver coating delivers stable wear behaviour when machining unalloyed and alloyed steel as well as cast iron. The coating lowers adhesive tendencies and improves heat resistance, so flank wear develops more predictably and indexable insert life increases. The E57 chipbreaker controls chip formation in both long‑chip and short‑chip conditions, reducing the need for manual intervention and lowering the risk of surface defects. Geometry that improves tool stability and surface finish The Trigon 80° shape with a 0.4 mm corner radius provides a robust cutting edge and reduced radial forces during bore enlargement. This geometry enhances concentricity and helps avoid chatter on small‑diameter drills and reamers, translating into fewer rejects and less rework. The T3 thickness contributes to insert rigidity; when combined with correct clamping and feed parameters, the result is a measurable improvement in dimensional consistency and surface quality. Practical integration and selection guidance The insert is supplied in the WOEX06T304‑E57 designation, making it straightforward to match with compatible toolholders. The WKP35S grade is aimed primarily at production environments where reliable repeatability is required across mixed batches of steel and cast iron. For machines running high throughput, this insert supports sustained cutting conditions while offering predictable wear intervals that simplify tool management and reduce downtime. Contact Metav Werkzeuge for tailored cutting data, compatible holders and to identify the optimal insert variants for specific machining tasks Technical Data SKU: WOEX06T304-E57-WKP35S-WALTER Article designation: WOEX06T304-E57 WKP35S Product type: Bohr-/Aufbohrwendeschneidplatte (drill/boring indexable insert) Series: Tiger‑tec Silver Facts Insert size: 06 Shape: Trigon 80° Corner radius: 0.4 mm Thickness: T3 Tolerance class: E Special features Grade/coating: WKP35S, Tiger‑tec Silver Chipbreaker: E57 Material application: steel (P) and cast iron (K) Execution: X FAQ What materials is this insert designed for? The WOEX06T304‑E57 WKP35S insert is optimised for machining steel (P) and cast iron (K), benefiting from the Tiger‑tec Silver coating for improved wear resistance. How does the chipbreaker affect machining? The E57 chipbreaker shapes chip flow to suit both long and short chip conditions, reducing the risk of clogging and improving surface integrity when using the WOEX06T304‑E57 WKP35S. Which toolholders are compatible with the insert geometry? Standard holders designed for trigon 80° indexable inserts and the WOEX06T304 series are compatible; Metav Werkzeuge can advise on the correct holder for specific machine spindles. Is this insert suitable for high‑speed applications? The Tiger‑tec Silver coating and the WKP35S grade support elevated cutting speeds in many steel and cast iron operations, subject to appropriate feed and cooling strategies. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and forms part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanation only; there is no affiliation between our company and the manufacturers named. The offered item is an original, factory‑new product from the stated manufacturer.
WOEX06T304-E57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of the Tiger‑tec Gold grade and a robust Trigon 80° geometry to achieve consistent chip control and extended edge life in drilling and boring operations; order directly via Metav Werkzeuge or contact our consultants for application advice. WOEX06T304-E57 WSP45G Trigon 80° indexable insert for drilling/boring — Walter Tools, Tiger‑tec Gold, 0.4 mm corner radius The WOEX06T304-E57 WSP45G is a Trigon 80° indexable insert designed for drilling and boring tasks, engineered to deliver stable cutting-edge performance across steel, stainless steel and high-temperature alloys. Tiger‑tec Gold PVD-coated grade WSP45G Trigon 80° geometry for stable engagement Versatile for steel, stainless and superalloys 0.4 mm corner radius and T3 thickness Reliable wear resistance for longer tool life The Tiger‑tec Gold PVD-coated grade provides a wear-resistant cutting surface that supports prolonged cutting cycles. With the WSP45G composition, the coating and substrate pairing is optimised to reduce abrasive and adhesive wear, which translates into fewer index changes and improved process stability. The result is a measurable increase in uptime and predictable tool performance in repetitive drilling and boring operations. Broad material capability reduces tool inventory This insert is designed for the ISO material groups P / M / S, meaning applicability to steel, stainless steel and heat-resistant superalloys (including titanium alloys). The versatile grade helps avoid frequent tool swaps between materials, supporting leaner tool inventories and simplified process planning. For workshops that machine mixed batches, the capability to handle varied workpiece materials increases throughput while maintaining surface quality and dimensional consistency. Geometry optimised for secure engagement and chip control The Trigon 80° shape, combined with the E57 chipbreaker, gives a confident cutting geometry for plunge and helical drilling as well as light boring passes. The modest 0.4 mm corner radius balances edge strength and positional accuracy, while the T3 plate thickness supports mechanical stability under axial load. Together these features reduce vibration, improve hole quality and assist reliable chip evacuation in confined drilling operations. Practical benefits for production efficiency Using a coated, versatile insert like this reduces auxiliary rework and supports consistent cycle times. The robust edge preparation and chip control characteristics contribute to repeatable hole tolerances and improved surface finish, which are particularly valuable in production environments where process reproducibility is essential. The combination of geometry and grade emphasises efficiency and process security rather than one-off performance gains. Discuss specific machining scenarios with Metav Werkzeuge to confirm suitability of the Tiger‑tec Gold insert for the intended application; Metav Werkzeuge can advise on optimal cutting data and toolholders — eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data SKU: WOEX06T304-E57-WSP45G-WALTER Designation: WOEX06T304-E57 Grade: WSP45G Series: Tiger‑tec Gold Manufacturer: Walter Tools Insert shape: Trigon 80° Chipbreaker: E57 Size: 06 Corner radius: 0.4 mm Thickness: T3 Tolerance class: E Material groups: P / M / S Facts Corner radius: 0.4 mm Included angle: 80° Plate size: 06 Thickness designation: T3 Tolerance: E Special features PVD-coated carbide grade Tiger‑tec Gold Versatile for steel, stainless steel and superalloys Trigon geometry for drilling and boring E57 chipbreaker for secure chip formation Robust edge for consistent tool life FAQ Is this insert suitable for both drilling and light boring operations? Yes. The WOEX06T304-E57 WSP45G Trigon insert is designed for drilling and light boring, with geometry and chip control optimised for stable engagement. Which workpiece materials are recommended for this grade? The Tiger‑tec Gold WSP45G grade supports ISO groups P, M and S — steel, stainless steel and heat‑resistant superalloys — making it suitable for mixed‑material production runs. What is the significance of the 0.4 mm corner radius? A 0.4 mm corner radius gives a compromise between edge strength and positional accuracy, helping the WOEX06T304-E57 WSP45G to resist chipping while maintaining hole quality. How does the E57 chipbreaker help in machining? The E57 chipbreaker is tuned to generate controlled chips and promote reliable evacuation in drilling cycles, which reduces interruptions and improves surface finish for the insert. Can this insert be used in high‑temperature alloys like titanium? Yes. The WSP45G grade and Tiger‑tec Gold coating are formulated to cope with the heat and low thermal conductivity of superalloys and titanium, supporting cutting‑edge stability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for descriptive purposes only and do not indicate any affiliation. The offered item is original, brand‑new goods from the manufacturer.
WOEX080408-E57 WKP25S Wendeplatten - Walter Tools
Benefit from the combination of a Tiger·tec Silver coating, an application-optimised WKP25S grade and a Trigon 80° geometry for reliable drilling and bore enlargement in steel and cast iron. Order the WOEX080408-E57 WKP25S directly via Metav Werkzeuge or consult Metav Werkzeuge’s advisors for application-specific guidance. WOEX080408-E57 WKP25S – indexable drilling/bore insert, Trigon 80°, Tiger·tec Silver (Walter Tools) A WOEX080408-E57 WKP25S is an indexable insert engineered for drilling and bore enlargement in steel and cast iron, combining a Trigon 80° form with the Tiger·tec Silver coated carbide for extended tool life and consistent chip control. Tiger·tec Silver coating for high wear resistance WKP25S grade optimised for steel and cast iron Trigon 80° geometry for stable cutting performance Corner radius 0.8 mm for reliable edge strength Higher uptime through advanced coating and grade The combination of Tiger·tec Silver technology and the WKP25S coated carbide grade delivers markedly improved wear resistance compared with uncoated grades. This coating system is developed for elevated thermal and abrasive loads encountered when machining steel and cast iron, converting material-specific heat and abrasion into predictable tool life. The result is fewer insert changes and more consistent cycle times—advantages that translate directly into higher machine availability and lower per-part tooling cost. One insert for steel and cast-iron operations Designed for the ISO material groups P and K, this insert supports efficient processing of steel (P) and cast iron (K) with a single geometry and grade. The WKP25S chemistry is tuned to manage the typical chip formation and heat patterns of these groups, reducing the need to switch grades between different workpieces. For production environments that handle mixed batches or varied components, this versatility reduces inventory complexity and simplifies process planning. Geometry that stabilises cutting and improves surface quality The Trigon 80° form offers a robust cutting edge and an insert shape that promotes stable engagement during drilling and bore enlargement. Combined with a corner radius 0.8 mm, the geometry increases edge strength and resists chipping under intermittent entry conditions. The chipbreaker E57 supports controlled chip formation, particularly beneficial where short or brittle chips are expected, improving evacuation and reducing the risk of re-cutting. These geometric choices help lower vibration and improve surface finish on demanding bores. Practical benefits for workshop integration As an indexable insert from the Tiger·tec Silver series, the component is compatible with standard machining workflows and established holder systems, enabling quick seat changes and predictable repeatability. The insert’s profile and grade are selected to support productive drilling cycles and stable tool life, which aids in planning preventive maintenance and minimising unplanned downtime. Where process reliability and consistent results are priorities, this insert offers a balance of performance and economy that fits production-focused environments. For machining tasks that demand repeatable results and low tool-change frequency, contact Metav Werkzeuge to specify the WOEX080408-E57 WKP25S for the intended application or request tailored process recommendations from Metav Werkzeuge’s consultants via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: WOEX080408-E57-WKP25S-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WOEX080408-E57 WKP25S Walter Tools Manufacturer: Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte Series: Tiger-tec Silver Facts Plate form: Trigon 80° Plate size: 08 Plate thickness: 04 Corner radius: 0.8 mm Chipbreaker: E57 Grade/sort: WKP25S Tolerance class: E Execution: X Special features Coating / technology: Tiger·tec Silver (coated carbide) Material compatibility: P / K (steel and cast iron) Application: drilling and bore enlargement Insert designation: WOEX080408-E57 WKP25S Robust edge for interrupted cuts Optimised chip control for short chips FAQ What materials is this insert suitable for? The WOEX080408-E57 WKP25S is formulated for steel (ISO group P) and cast iron (ISO group K), offering balanced performance across both material families. What benefit does the Tiger·tec Silver coating provide? Tiger·tec Silver on the WKP25S grade enhances thermal and abrasive resistance, increasing insert life and stabilising cutting conditions in demanding operations. How does the Trigon 80° form affect machining? The Trigon 80° geometry improves edge support and cutting stability during drilling and bore enlargement, reducing vibration and promoting consistent surface finish. What role does the chipbreaker E57 play? The E57 chipbreaker controls chip formation for short, brittle chips—particularly useful when machining cast iron—helping to avoid chip entanglement and improve evacuation. Is the corner radius suitable for interrupted cuts? With a corner radius of 0.8 mm, the insert provides enhanced edge strength that resists chipping under intermittent entry, making it appropriate for less continuous engagement. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is an original, factory-new product of Walter Tools.
WOEX080408-E57 WKP35S Wendeplatten - Walter Tools
WOEX080408-E57 WKP35S Bohr-/Aufbohrwendeschneidplatte von Walter Tools Die WOEX080408-E57 WKP35S ist eine Trigon 80° Wendeschneidplatte zur effizienten Bohr- und Aufbohrbearbeitung von Stahl und Gusseisen Trigon 80° Form für stabile Schnittführung Tiger-tec Silver Beschichtung für längere Standzeit Eckenradius 0,8 mm für präzise Konturarbeit Geeignet für Stahl und Gusseisen nach ISO Spanbrecher E57 optimiert Spanbildung Materialqualität und Beschichtung für dauerhafte Leistung Die Wendeschneidplatte basiert auf beschichtetem Hartmetall der Serie Tiger-tec Silver, wodurch abrasive Beanspruchung reduziert und die Standzeit erhöht wird. Aufgrund der Beschichtung zeigt die Sorte WKP35S verbesserte Verschleißfestigkeit, was insbesondere bei Serienbearbeitung zu weniger Werkzeugwechseln und höherer Produktivität führt. Anwender profitieren von konstanter Schnittgüte und planbaren Wechselintervallen. Zerspanungsfelder: Fokus auf Stahl und Gusseisen Für die Bearbeitung von Stahl (ISO-Gruppe P) und Gusseisen (ISO-Gruppe K) ist die Platte spezialisiert, wobei die Zuschneideparameter auf typische Spanformer und Wärmeentwicklung abgestimmt sind. Unterschiedliche Guss- und Stahlgüten lassen sich mit angepassten Schnittwerten wirtschaftlich veredeln, wodurch die Platte in Werkstätten und Fertigungsstraßen vielseitig einsetzbar ist. Geometrie und Spanbeeinflussung für Prozesssicherheit Die Trigon 80° Geometrie in Verbindung mit dem Spanbrecher E57 sorgt für kontrollierte Spanbildung und stabile Schneidkantenführung. Genau dieses Zusammenspiel reduziert Vibrationen und verbessert die Oberflächengüte im Bohr- und Aufbohrprozess. Anwender erhalten dadurch reproduzierbare Ergebnisse bei anspruchsvollen Toleranzen. Präzision durch definierte Kanten und Radien Der Eckenradius von 0,8 mm bietet eine ausgewogene Kombination aus Zähigkeit und Schneidleistungsfähigkeit, was Konturtreue und Maßhaltigkeit unterstützt. Insbesondere bei wiederholten Bearbeitungsschritten sichert der Radius die Robustheit der Schneidkante und trägt so zur Prozesssicherheit bei. Wirtschaftlichkeit und Einsatz in der Fertigung Durch die Kombination aus robuster Sorte und hochwertiger Beschichtung sinken Stillstandszeiten und Werkzeugkosten pro gefertigte Einheit. Die Platte eignet sich besonders für Anwender, die konstante Produktionsraten mit hoher Wiederholgenauigkeit und guter Oberflächenqualität benötigen. Empfehlung für Anwender und Integration in Werkzeughalter Die Bauform und Abmessungen sind auf handelsübliche Aufnahmen ausgelegt; eine Anpassung der Schnittwerte an Maschine und Werkstoff empfiehlt sich für maximale Leistung. Werkstattbetriebe profitieren von der einfachen Einbindung in bestehende Spann- und Werkzeugkonzepte. Empfehlung: Für produktive Bohr- und Aufbohrprozesse empfiehlt sich die Verwendung der WOEX080408-E57 WKP35S von Walter Tools mit Tiger-tec Silver Beschichtung; bei Fragen zur Anwendung oder zur Auswahl des passenden Werkzeughalters gern Kontakt aufnehmen unter info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 Produktmerkmale Artikelnummer: WOEX080408-E57-WKP35S-WALTER Bezeichnung: WOEX080408-E57 WKP35S Marke: Walter Tools Serie: Tiger-tec Silver Produktart: Bohr-/Aufbohrwendeschneidplatte Ausführung: X Daten Eckenradius: 0,8 mm Plattengröße: 08 Plattendicke: 04 Plattenform: Trigon 80° Spanbrecher: E57 Besonderheiten Schneidstoffsorte: WKP35S (beschichtetes Hartmetall) Beschichtung: Tiger·tec Silver Toleranzklasse: E Materialangabe: P / K (P: Stahl, K: Gusseisen) Einsatzgebiet: Bohr- und Aufbohrbearbeitung FAQ Welche Werkstoffe lassen sich mit der Platte bearbeiten? Die WOEX080408-E57 WKP35S von Walter Tools ist für Stahl (ISO-Gruppe P) und Gusseisen (ISO-Gruppe K) ausgelegt und wurde für typische Span- und Wärmebedingungen dieser Werkstoffe optimiert. Wie beeinflusst die Tiger-tec Silver Beschichtung die Standzeit? Die Tiger-tec Silver Beschichtung reduziert abrasiven Verschleiß und thermische Beanspruchung, wodurch die Standzeit der WKP35S Platte im Vergleich zu unbeschichteten Sorten deutlich verbessert wird. Welche Vorteile bietet die Trigon 80° Form bei Bohr- und Aufbohrprozessen? Die Trigon 80° Geometrie sorgt für stabile Schneidkante und gleichmäßige Spanabfuhr, was zu verbesserter Oberflächengüte und reduzierten Vibrationen beim Bohren führt. Wann ist der Spanbrecher E57 die richtige Wahl? Der Spanbrecher E57 ist geeignet, wenn kurze, kontrollierte Späne gewünscht werden, etwa bei wechselnden Gussqualitäten oder when Prozessstabilität und Spanbruch im Vordergrund stehen. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
WOEX080408-E57 WSP45G WSP45G Wendeplatten - Walter Tools
Benefit from a combination of high process reliability and versatile material capability: the Tiger·tec Gold WSP45G grade provides consistent cutting-edge stability and the Trigon 80° geometry with a 0.8 corner radius supports secure chip control during drilling and reaming operations; procure the insert via Metav Werkzeuge or consult our specialists for application-specific advice. WOEX080408-E57 WSP45G indexable insert – Tiger·tec Gold PVD-coated carbide for drilling and reaming, Walter Tools WOEX080408-E57 WSP45G is an indexable insert designed for drilling and reaming tasks, featuring a trigon geometry and a dedicated E57 chipbreaker for secure chip formation across a wide range of materials. Tiger·tec Gold PVD-coated grade WSP45G Suitable for Stahl, rostfreier Stahl and high-temp alloys Trigon 80° shape with 0.8 corner radius E57 chipbreaker for controlled chip evacuation Reliable coating technology for predictable cycle times The Tiger·tec Gold coating and the WSP45G grade combine to deliver a coated carbide solution engineered for repeatable performance. The PVD-based coating increases wear resistance and supports a stable cutting edge, which translates into fewer tool changes and more predictable machining cycles. For production-focused environments, this stability reduces unplanned downtime and contributes to a consistent surface finish during drilling or reaming operations. The specified grade is optimised for the thermal and mechanical loads encountered when machining Stahl, rostfreier Stahl and demanding alloyed materials. Geometry and chip control that improve process security The Trigon 80° plate form with a 0.8 corner radius offers a robust cutting geometry that balances edge strength and entry characteristics in holemaking. Combined with the E57 chipbreaker, the insert promotes controlled chip formation and evacuation, which reduces the risk of chip jamming and edge build-up when working in ductile or sticky materials. This geometric setup supports safer, more stable feed rates and consistent hole quality, making the insert a practical choice for repetitive drilling and reaming tasks where process security is a priority. Practical benefits for workshop and production planning Using this indexable solution helps to streamline tool inventory: one insert grade covers multiple material groups (P / M / S), enabling straightforward tool selection across different jobs. The robust coated carbide composition reduces flank wear and helps to maintain tolerances over longer tool lives, which in turn lowers intervention time for tool changes. For production planners this means simpler tool lists, fewer setup interruptions and improved overall equipment effectiveness (OEE) in drilling operations. Application guidance and compatibility considerations The insert’s specification (WOEX080408-E57 WSP45G) suits modular drilling and reaming systems that accept Trigon-style plates; the E-class tolerance ensures consistent seat fit and interchangeability in compliant toolholders. The WSP45G grade is particularly suitable where a balance of toughness and wear resistance is required—such as interrupted cuts or operations with moderate temperatures—and supports secure chip control thanks to the E57 chipbreaker design. For specific holder compatibility and feed/speed recommendations consult the technical advisors at Metav Werkzeuge or refer to machine tool supplier guidelines. Contact Metav Werkzeuge for application-specific recommendations and to obtain Walter Tools' WOEX080408-E57 WSP45G inserts, ensuring optimal selection for drilling and reaming tasks Technical Data Article number: WOEX080408-E57-WSP45G-WALTER SKU: WOEX080408-E57-WSP45G-WALTER Designation: WOEX080408-E57 WSP45G Manufacturer: Walter Tools Facts Plate size: 08 Plate thickness: 04 Corner radius: 0.8 Geometry: Trigon 80° Chipbreaker: E57 Tolerance class: E Special features Series: Tiger-tec Gold Grade: WSP45G Material: coated carbide Material applications: P / M / S (Stahl, rostfreier Stahl, superalloys/titanium) Execution: X FAQ What materials can this insert machine reliably? The WOEX080408-E57 WSP45G insert from Walter Tools is specified for P / M / S applications and is suitable for machining Stahl, rostfreier Stahl and heat-resistant superalloys including titanium. How does the Trigon 80° shape affect drilling performance? The Trigon 80° geometry provides a strong cutting edge and good entry characteristics for holemaking; combined with the E57 chipbreaker it improves chip control and reduces the risk of edge build-up during drilling and reaming. What advantage does the Tiger·tec Gold coating offer? Tiger·tec Gold enhances wear resistance and cutting-edge stability on the WSP45G grade, supporting longer tool life and more consistent performance across varied production runs. Is the insert compatible with standard Trigon toolholders? The WOEX080408-E57 WSP45G is designed for Trigon-style seats and the E tolerance class ensures accurate seating; compatibility should be verified against the specific toolholder documentation. What role does the 0.8 corner radius play in application? A 0.8 corner radius increases edge strength and helps to absorb shock in interrupted cuts, while still enabling precise hole profiles in drilling and reaming operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and brand names mentioned are the property of their respective owners. Their inclusion serves explanatory purposes only and does not imply any affiliation with our company. The offered article is original, factory-new merchandise of the named manufacturer.
WOEX100508-E57 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating, a precise Trigon 80° geometry and the WKP35S grade for reliable holemaking in steel and cast iron; order directly via Metav Werkzeuge or ask the consultants for application-specific advice. WOEX100508-E57 WKP35S drilling/reaming indexable insert — Trigon 80°, Tiger‑tec Silver (Walter Tools) WOEX100508-E57 WKP35S is a drilling/reaming indexable insert designed for productive holemaking and enlarging operations in steel and cast iron, offering controlled chip formation and stable cutting edges. Tiger‑tec Silver coated carbide grade Trigon 80° geometry for stable drilling Optimised E57 chipbreaker for clean chips Suitable for steel and cast iron (P/K) Boosted productivity with dependable coating and grade The combination of the Tiger‑tec Silver coating and the WKP35S grade provides a balance of wear resistance and thermal stability that supports longer tool life under repetitive holemaking cycles. The coated carbide substrate resists abrasive wear commonly encountered when machining cast iron, while the design of the grade mitigates heat-related edge deterioration when cutting various classes of steel. As a result, batch processes benefit from fewer insert changes and more predictable tool-wear behaviour, which in turn supports consistent production throughput and reduced machine downtime. Geometry that secures repeatable hole quality The Trigon 80° plate form and the corner radius 0.8 contribute to secure seating in drill bodies and consistent edge engagement during entry and exit. The truncated-trigon outline gives a favourable cutting-edge angle for stable cutting forces and improved runout tolerance, leading to better hole cylindricity and surface finish compared with less rigid geometries. The tolerance class E and plate thickness 05 support precise indexing and repeatable clamping, making the insert suited to series production where dimensional consistency is required. Chip control and process reliability for mixed-material shops Equipped with the E57 chipbreaker, this insert promotes controlled chip segmentation during drilling and enlargement, reducing the risk of long, entangling chips and improving evacuation from the hole. The chipbreaker geometry is adapted to the typical chip forms of both P (steel) and K (cast iron) workpiece groups, so machinists experience fewer interruptions for chip clearing and less heat concentration at the cutting edge. The net effect is a more reliable machining cycle and a reduced likelihood of surface damage or rework. Application scope and practical considerations for tooling planners Intended primarily for holemaking operations in steel and cast iron, the insert suits production environments that prioritise repeatability and stable cutting conditions. The insert designation WOEX100508-E57 WKP35S identifies the geometry and chipbreaker combination that matches many standard drill and boring-holder systems; selection of appropriate axial and radial depths of cut should follow the machine and holder manufacturer’s recommendations. Where process optimisation is required, choosing the matching insert grade and chip control can significantly reduce the total cost per hole through fewer replacements and consistent part quality. Contact Metav Werkzeuge for tailored recommendations on Walter Tools WOEX100508-E57 WKP35S inserts and for expert ordering assistance via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: WOEX100508-E57-WKP35S-WALTER Product type: drilling/reaming indexable insert Brand: Walter Tools Series: Tiger‑tec Silver ISO designation: WOEX100508-E57 WKP35S Facts Plate size: 10 Plate thickness: 05 Corner radius: 0.8 mm Plate form: Trigon 80° Chipbreaker: E57 Tolerance class: E Special features Coating: Tiger‑tec Silver (coated carbide) Grade: WKP35S Material suitability: P (steel), K (cast iron) Execution: X Label/SKU: WOEX100508-E57-WKP35S-WALTER FAQ What materials is this insert suitable for? The WOEX100508-E57 WKP35S insert is formulated for machining steel (P) and cast iron (K) workpiece groups and performs well across typical grades within those ISO categories. How does the E57 chipbreaker affect holemaking? The E57 chipbreaker promotes controlled chip segmentation and evacuation during drilling and enlarging operations, which reduces chip entanglement and supports uninterrupted production cycles. Is the Trigon 80° geometry beneficial for repeatability? Yes. The Trigon 80° form provides a stable cutting geometry and reliable seating in holders, contributing to repeatable hole quality and improved resistance to runout-related errors. Which series and grade describe the insert’s wear properties? This insert belongs to the Tiger‑tec Silver series and uses the WKP35S grade, a coated carbide formulation designed for balanced wear resistance and thermal stability in mixed steel and cast iron applications. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are used solely for explanatory purposes. There is no connection between our company and the named brands. The offered item is original, factory-new goods of the manufacturer.
WOEX100508-E57 WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger·tec Gold coating, versatile P/M/S material capability and the Trigon 80° geometry for reliable performance in demanding drilling and boring operations; order the insert via Metav Werkzeuge or contact our consultants for application support. WOEX100508-E57 WSP45G indexable insert for drilling/boring by Walter Tools — Tiger·tec Gold PVD coating, Trigon 80° WOEX100508-E57 WSP45G is an indexable drilling and boring insert designed for robust material removal in a wide range of steels and heat-resistant alloys Tiger·tec Gold PVD coating for long tool life Suitable for steel, stainless and superalloys Trigon 80° geometry for stable engagement E57 chipbreaker for predictable chip control Steady cutting performance through advanced coating technology The Tiger·tec Gold surface treatment delivers thermal stability and wear resistance that directly reduces flank and crater wear during intermittent and continuous cuts. Combined with the PVD coated carbide grade of the insert, this results in more consistent machining cycles and fewer unplanned tool changes. The described coating technology is engineered to maintain cutting-edge integrity when machining steel, stainless steel and demanding superalloys and titanium, which helps stabilise the process and supports higher cutting speeds without sacrificing surface finish or component tolerances. Geometry and chip control that protect process stability The Trigon 80° form of the insert promotes secure engagement in bore and reaming operations, lowering the tendency for insert pull-out and improving entry behaviour. The E57 chipbreaker is tuned to the geometry to encourage controlled chip formation and evacuation, which reduces the risk of built-up edge and coolant blockage. With a corner radius of 0.8 mm, the cutting edge balances strength and sharpness, enabling reliable edge life while maintaining acceptable surface integrity. These geometric choices make the component suitable for stable, repeatable production runs and shorter cycle times. Versatility that reduces tooling complexity and downtime Designed as an application-flexible indexable insert, this product supports a broad spectrum of machining tasks across multiple material groups denoted by P/M/S. That versatility reduces the need for frequent tool changes and simplifies inventory management in the workshop. The WOEX100508-E57 WSP45G insert is particularly appropriate where a single tooling solution is preferred for both medium-duty steel work and tougher stainless or heat-resistant alloy components; the result is improved overall productivity and lower per-part tooling cost in mixed-production environments. For tailored application advice or stock information on this Walter Tools WOEX100508-E57 WSP45G insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: WOEX100508-E57-WSP45G-WALTER Article designation: WOEX100508-E57 WSP45G Product type: Bohr-/Aufbohrwendeschneidplatte Manufacturer: Walter Tools Series: Tiger-tec Gold Core data Plate form: Trigon 80° Plate size: 10 Plate thickness: 05 Corner radius: 0.8 mm Chipbreaker: E57 Tolerance class: E Materials & special features Material class: P / M / S Coating / grade: WSP45G (PVD coated carbide) Technology: Tiger·tec Gold Execution: X Suitable for: Steel, stainless steel, superalloys and titanium FAQ What materials can this insert machine effectively? This insert from Walter Tools is specified for P / M / S groups, meaning it is suitable for steel, stainless steel and heat-resistant superalloys including titanium applications. How does the Trigon 80° geometry affect drilling and boring? The Trigon 80° shape improves engagement stability during penetration and reduces the tendency for insert pull-out, supporting consistent hole quality in repetitive operations. What benefit does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating enhances thermal stability and wear resistance, which supports longer edge life and more predictable performance under elevated cutting speeds. Is the E57 chipbreaker suitable for mixed production? Yes, the E57 chipbreaker offers controlled chip formation across a variety of workpiece materials, aiding chip evacuation and helping to prevent built-up edge in mixed-material batches. Can this insert be used for both drilling and reaming operations? The design intent of this Bohr-/Aufbohrwendeschneidplatte makes it applicable to drilling and upboring tasks where the geometry and chip control features align with the machining strategy. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only; there is no connection between our company and the named brands. The offered item is an original, unused product from the manufacturer Walter Tools.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com