XNHF090612-D27 WKP25S Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver coating, the WKP25S grade and the D27 chipbreaker for improved process reliability and longer tool life — order original Walter Tools inserts directly via Metav Werkzeuge or consult our specialists for application advice. XNHF090612-D27 WKP25S indexable milling insert — Tiger·tec Silver, Walter Tools The XNHF090612-D27 WKP25S is an indexable milling insert engineered for efficient machining of steel and cast iron, offering robust wear resistance and consistent chip control in diverse milling applications. Tiger·tec Silver coating for extended life WKP25S grade for steel and cast iron D27 chipbreaker improves chip control 0° negative clearance for tough cuts Higher productivity through proven coating and grade The combination of the Tiger·tec Silver coating and the WKP25S grade delivers a significant uplift in wear resistance and cutting-edge stability. As a coated cemented carbide solution, this insert resists abrasive wear typical when machining steel and cast iron, which reduces tool-change frequency and increases uptime. The enhanced coating technology supports higher sustained cutting parameters, so cycle times are reduced while part tolerances remain consistent. This results in a lower cost per component and improved overall process reliability for production runs and mixed-batch operations. Consistent chip control and surface quality for predictable results Built with a D27 chipbreaker, a corner radius 1.2 mm and a negative clearance of 0°, the insert promotes controlled chip formation and evacuation even under interrupted cuts. The chipbreaker geometry helps to break and direct chips reliably, which reduces the risk of re-cutting and protects the workpiece surface. The modest corner radius contributes to a dependable cutting edge that balances strength and surface finish, making the insert suited to both roughing passes and semi-finish operations where repeatable quality is required. Reduced edge chipping and stable cutting behaviour lower scrap rates and machine downtime. Practical integration and material suitability for shop floors Presented as an indexable insert with the ISO designation XNHF090612-D27 WKP25S, this component is produced to tolerance class H and is compatible with standard clamping systems that accept the listed geometry. The insert thickness (06) and plate size (09) offer mechanical stability for heavier cuts, while the material designation P / K confirms suitability per ISO 513 for unalloyed and alloyed steels as well as cast iron. In practice, the insert is well suited to applications ranging from general-purpose milling of structural steels to more demanding cast-iron components, providing reliable performance across a wide range of production scenarios. For application-specific recommendations or to order original Walter Tools inserts such as the XNHF090612-D27 WKP25S, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt, expert assistance Technical Data Article number: XNHF090612-D27-WKP25S-WALTER Label: Fräswendeschneidplatte XNHF090612-D27 WKP25S Walter Tools ISO designation: XNHF090612-D27 WKP25S Facts Free clearance: 0° (negative) Corner radius: 1.2 mm Thickness: 6 mm Plate size: 09 Tolerance class: H Special features Grade: WKP25S Series: Tiger·tec Silver Chipbreaker: D27 Material designation: P / K (steel and cast iron) Execution: F Manufacturer: Walter Tools FAQ Which materials can be machined with this insert? The XNHF090612-D27 WKP25S insert is designed for machining steel and cast iron (material groups P and K according to ISO 513), as indicated by the WKP25S grade. What is the purpose of the D27 chipbreaker? The D27 chipbreaker on the XNHF090612-D27 WKP25S promotes controlled chip formation and evacuation, improving surface quality and reducing the risk of re-cutting. Is this a coated insert and what benefit does the coating provide? Yes, the insert features Tiger·tec Silver coating; this coating enhances wear resistance and supports more stable cutting conditions for longer tool life. What does the 0° negative clearance mean for cutting operations? A 0° negative clearance provides a more robust cutting edge for demanding cuts, helping to resist edge deformation during heavy or interrupted milling with the XNHF090612-D27 WKP25S. Which tolerance and dimensions are relevant for tool selection? The insert is produced to tolerance class H, with a corner radius of 1.2 mm, thickness 6 mm and plate size 09, which should be matched to a compatible toolholder and application. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (marketed as Walter Tools) with headquarters in Tübingen belongs to the global group of precision tooling manufacturers and is part of the Swedish Sandvik Group. Protected trademarks and brand names are the property of their respective owners and are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is an original factory-new product of the manufacturer.
XNHF090612-D27 WKP35G Wendeplatten - Walter Tools
Take advantage of the proven combination of the Tiger‑tec Gold coating and the WKP35G grade for stable, productive milling in steel and cast iron; the insert’s 0° negative rake and 1.2 mm corner radius deliver secure cutting and consistent tool life. Order directly via Metav Werkzeuge or consult our specialists for application advice. XNHF090612-D27 WKP35G Milling Insert — Tiger‑tec Gold, D27 chipbreaker (Walter Tools) The XNHF090612-D27 WKP35G is a negative‑rake milling insert designed for robust milling of steel and cast iron in industrial machining. Tiger‑tec Gold coating for long tool life Grade WKP35G for steel and cast iron 0° negative rake for stable cutting 1.2 mm corner radius for secure engagement Delivering repeatable productivity with Tiger‑tec Gold The combination of the Tiger‑tec Gold coating and the WKP35G carbide formulation provides a balanced mix of wear resistance and edge stability. This engineered surface treatment reduces adhesive wear and preserves the cutting edge during continuous operation, which translates into longer tool life and fewer index changes. For production environments where uptime and predictable tool performance matter, these properties support higher productivity and consistent component quality. Geometry that promotes process reliability The insert’s 0° negative rake geometry and 1.2 mm corner radius contribute directly to mechanical strength at the cutting edge. A neutral/negative rake reduces the cutting forces transmitted to the insert and the toolholder, improving stability during interrupted cuts or heavy engagement. The slightly rounded corner radius distributes load across a larger edge area, decreasing the risk of chipping and helping to maintain dimensional accuracy over longer tool life. Chip control and material adaptability Equipped with the D27 chipbreaker, this insert is tuned for controlled chip formation in both ISO P (steel) and ISO K (cast iron) applications. The chip control geometry assists in producing short, manageable chips in cast materials and more uniform chips in steels, reducing rework risk and enhancing operator safety. The WKP35G grade is optimised for the thermal and abrasive conditions typical of these material groups, enabling productive machining across a broad workpiece spectrum. Integration into machining systems and selection tips The designation XNHF090612‑D27 refers to the insert geometry and fitment family; it is compatible with toolholders that accept this format. When selecting the cutting data, prioritise stable clamping and a rigid setup to exploit the insert’s strengths: the coating and geometry are designed to reward consistent spindle speeds and steady feed per tooth rather than extreme, unstable cuts. For process planning, consider the WKP35G insert where a balance of wear resistance and edge robustness is required in mixed production of steel and cast iron components. Discuss application-specific recommendations for Walter Tools Tiger‑tec Gold inserts with Metav Werkzeuge: email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and ordering. Technical data SKU: XNHF090612-D27-WKP35G-WALTER Article designation: XNHF090612-D27 WKP35G Label: Fräswendeschneidplatte XNHF090612-D27 WKP35G Walter Tools Series: Tiger‑tec Gold Grade: WKP35G Facts Negative rake angle: 0° Corner radius: 1.2 mm Plate size code: 09 Plate thickness code: 06 Special features Chipbreaker: D27 Suitable workpiece materials: steel (ISO P), cast iron (ISO K) Execution: F Tolerance class: H Product type: milling insert (indexable insert) FAQ What materials can this insert machine effectively? The XNHF090612‑D27 WKP35G insert is designed for machining steel (ISO P) and cast iron (ISO K), with the WKP35G grade tuned to handle the typical heat and chip forms of these groups. How does the Tiger‑tec Gold coating improve performance? The Tiger‑tec Gold coating increases wear resistance and thermal stability, which helps the insert maintain its cutting edge longer and supports consistent performance in continuous milling operations. What is the benefit of a 0° negative rake for milling? A 0° negative rake improves cutting stability and reduces edge vulnerability under heavy or interrupted cuts, contributing to more reliable machining and longer insert life. Which chip behaviour does the D27 chipbreaker encourage? The D27 chipbreaker promotes controlled, short-to-medium chips in cast iron and better chip control in steels, facilitating safer handling and fewer issues with chip evacuation. How can I ensure correct integration with my toolholder? Select a toolholder that accepts the XNHF090612‑D27 format; the insert designation indicates the geometry and seating. Maintain rigid clamping and stable cutting parameters to exploit the insert’s coating and geometry. Walter Tools: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools) is a leading provider of precision cutting tools and belongs to the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. The mentioned product is an original factory‑new article of the manufacturer. There is no affiliation between our company and the listed brands.
XNHF090612-D57 WKK25G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating and the WKK25G grade for consistent, wear-resistant performance when machining cast iron; the negative 0° rake and D57 chipbreaker ensure stable, short-chip formation for productive milling. Order the insert directly via Metav Werkzeuge or consult the technical team for application advice. XNHF090612-D57 WKK25G Milling indexable insert for cast iron – Walter Tools The XNHF090612-D57 WKK25G milling insert provides robust, coated-carbide performance optimised for cast iron milling in industrial production. Tiger·tec Gold coating for wear resistance Optimised for cast iron machining Negative 0° rake for stable cutting 1.2 mm corner radius for robust edge Reliable performance on abrasive workpieces The combination of Tiger·tec Gold coating and the WKK25G grade delivers enhanced resistance to abrasive wear, a common challenge when machining cast iron. The coated carbide composition is tailored to maintain cutting-edge integrity under intermittent contact and frequent chip breaking. This results in extended tool life and fewer tool changes, improving uptime and lowering process interruptions. The built-in chipbreaker D57 supports controlled, short-chip evacuation, which reduces the risk of workpiece damage and keeps cycle times consistent. Stable cutting geometry for predictable results A negative 0° rake angle provides a stable cutting geometry that favours rigidity and repeatable performance during milling operations. Combined with a 1.2 mm corner radius, the insert tolerates higher mechanical loads and delivers smoother transitions in interrupted cuts. These characteristics make the insert suitable for production environments where consistent tolerances and surface integrity are required. The tolerance class H further supports precision in seatings and toolholder interfaces, helping to maintain process control across multiple parts. Practical advantages for process optimisation By focusing on essential features such as the coated carbide grade and the proven Tiger·tec Gold technology, the insert contributes to predictable tool behaviour and easier process planning. The chip control strategy embedded in the design helps to avoid long, stringy chips that could foul fixtures or conveyors. With clear designation and standardised form factors, integration into existing milling programmes and tool repositories becomes straightforward, reducing setup time and simplifying tool management across batches. Integration into production workflows The insert’s size and thickness coding allow for uniform handling and replacement within modular tooling systems. Clear identification of series and grade assists in inventory control and reordering, while the combination of durable coating and robust geometry supports longer intervals between inspections. For process engineers, the result is a practical balance between productivity and predictable wear behaviour, enabling more reliable cycle planning and reduced downtime in cast iron machining. Contact Metav Werkzeuge for application-tailored advice on Walter Tools Tiger·tec Gold inserts and to discuss optimal grade selection and holder compatibility via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: XNHF090612-D57-WKK25G-WALTER Designation: XNHF090612-D57 WKK25G Manufacturer: Walter Tools Series: Tiger·tec Gold Grade: WKK25G Application: Cast iron Facts Corner radius: 1.2 mm Plate size: 09 Plate thickness: 06 Free rake angle: 0° Tolerance class: H Chipbreaker: D57 Special features Coating: Tiger·tec Gold Material: Coated carbide Suited for: Cast iron machining Optimised for abrasive wear resistance Stable, short-chip formation Designed for productive milling FAQ What materials is this insert intended for? The XNHF090612-D57 WKK25G insert is designed primarily for machining cast iron, with the WKK25G grade optimised to resist abrasive wear and handle short, breaking chips. How does the Tiger·tec Gold coating influence tool life? The Tiger·tec Gold coating enhances wear resistance and thermal stability, which helps the tool maintain cutting performance for longer periods under the abrasive conditions typical of cast iron. What is the effect of the negative 0° rake on machining? A negative 0° rake provides a stiffer cutting geometry that improves stability in interrupted cuts and supports consistent edge life during heavy or variable engagement. Can this insert be used for roughing and finishing? The combination of the 1.2 mm corner radius and the D57 chipbreaker allows the insert to perform reliably in robust roughing operations and maintain acceptable surface integrity in less demanding finishing passes. How does the chipbreaker D57 improve production? The D57 chipbreaker produces short, controllable chips that reduce the risk of chip entanglement, improve evacuation, and protect fixtures and conveyors in automated production settings. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trade names and trademarks are the property of their respective owners. Brand names and protected designations are used for explanatory purposes only; there is no affiliation between our company and the mentioned brands. The offered item is an original, factory-new product of the stated manufacturer.
XNHF090612-D57 WKP25S WKP25S Wendeplatten - Walter Tools
Take advantage of high process reliability and broad material coverage combined with the durable Tiger·tec Silver coating for stable chip control and long tool life; order the insert directly via Metav Werkzeuge or consult the Metav team for application support. XNHF090612-D57 WKP25S — indexable milling insert, Tiger·tec Silver coating, for steel and cast iron · Walter Tools XNHF090612-D57 WKP25S is an indexable milling insert optimised for efficient roughing and semi-finishing of steel and cast iron components, offering high edge stability in demanding production environments. Tiger·tec Silver coating for long tool life Coated carbide grade WKP25S Suitable for steel and cast iron machining 0° negative rake with 1.2 mm corner radius Proven process security and consistent machining results The Tiger·tec Silver technology combined with the WKP25S coated-carbide grade provides reliable wear resistance and heat management during high-power milling operations. This combination reduces flank and crater wear, which supports longer tool life and fewer interruptions in production. Designed for common steel and cast iron applications, the insert promotes predictable performance across typical shopfloor feeds and speeds, aiding stable cycle times and consistent component quality. Geometry tailored for controlled chip formation and surface quality The insert’s D57 chipbreaker geometry and 0° negative rake are configured to produce short, controllable chips when machining abrasive or brittle materials. The 1.2 mm corner radius improves edge robustness, reducing the risk of premature edge chipping while maintaining acceptable surface finish during heavy cuts. These geometric choices translate into fewer insert changes and reduced rework, improving overall process efficiency without sacrificing component aesthetics or dimensional stability. Economic machining through broad material coverage and easy integration As a coated-carbide insert approved for machining both steel (P) and cast iron (K) according to ISO groupings, the grade offers flexibility across mixed-production environments. The stable cutting edge and coating synergy mean that fewer grades are required to cover multiple applications, simplifying inventory and tooling strategies. Integration into standard milling systems is straightforward thanks to the common designation and compatibility, supporting productive machining with predictable maintenance intervals. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger·tec Silver inserts and application-specific cutting data — Metav Werkzeuge can advise on grade WKP25S and supply the XNHF090612-D57 insert; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: XNHF090612-D57-WKP25S-WALTER Designation: XNHF090612-D57 WKP25S Series: Tiger-tec Silver Grade: WKP25S Material group: P / K Chipbreaker: D57 Manufacturer: Walter Tools Facts Corner radius: 1,2 Thickness: 06 Size: 09 Free rake angle: 0° (negativ) Tolerance class: H Execution: F Special features Coating technology: Tiger·tec Silver Grade type: coated carbide Suitable materials: steel (P), cast iron (K) Application focus: milling (roughing / semi-finishing) Edge form: robust 1.2 mm corner radius Chip control: D57 geometry for short chips FAQ What materials is this insert suitable for? The XNHF090612-D57 WKP25S insert (Walter Tools) is designed for machining steel (P) and cast iron (K) according to the ISO material groupings indicated for the WKP25S grade. How does the Tiger·tec Silver coating affect tool life? The Tiger·tec Silver coating on the WKP25S grade improves thermal resistance and reduces adhesive wear, which helps the insert maintain cutting-edge integrity and extends service intervals under typical milling conditions. What benefit does the 0° negative rake provide? A 0° negative rake increases edge stability under heavy cutting loads; in the XNHF090612-D57 design this contributes to reliable performance during interrupted cuts and abrasive workpiece conditions. Which chipbreaker is used and why does it matter? This insert uses the D57 chipbreaker geometry, which produces short, controllable chips suitable for mixed production of steel and cast iron, reducing the risk of entanglement and improving surface consistency. Is the insert compatible with standard milling cutters? The insert designation XNHF090612-D57 WKP25S follows common industry formats and is compatible with holders and cutters designed for this size and form, enabling straightforward integration into existing setups. Protected trademarks and trade names are the property of their respective owners and are mentioned here for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original factory-new product of the manufacturer. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
XNHF0906ANN-D27 WKK25G Wendeplatten - Walter Tools
XNHF0906ANN-D27 WKK25G Fräswendeschneidplatte von Walter Tools Die XNHF0906ANN-D27 WKK25G ist eine beschichtete Fräswendeschneidplatte für die produktive Bearbeitung von Gusseisen im Tiger·tec Gold-Programm. Beschichtetes Hartmetall Tiger·tec Gold Optimiert für Gusseisen mit stabilem Spanbruch Negativer Freiwinkel 0° für robuste Schneidkante Spanbrecher D27 für kurze, kontrollierbare Späne Höhere Produktivität beim Gussfräsen durch gezielte Sortenauswahl Die Kombination aus WKK25G-Schneidstoff und der Tiger·tec Gold-Beschichtung ist speziell auf die Herausforderungen beim Zerspanen von Gusseisen ausgelegt. Dadurch reduziert sich der Werkzeugverschleiß bei abrasiven Werkstoffen, was längere Standzeiten und weniger Rüstzyklen ermöglicht. Anwender profitieren von konstanteren Bearbeitungsprozessen und einer planbaren Produktionsleistung durch die abgestimmte Werkstofftechnik. Zuverlässige Standzeit und bessere Oberflächenqualität Die negative Freiwinkelgeometrie von 0° wirkt stabilisierend auf die Schneidkante und sorgt für hohe Prozesssicherheit bei wechselnden Schnittbedingungen. Der Spanbrecher D27 formt kurze, brüchige Späne, die Materialabfuhr und Werkzeugkühlung erleichtern. Das Resultat ist eine konstante Bearbeitungsqualität und reduzierte Nacharbeit dank gleichmäßiger Spanbildung. Zweckgebundene Anwendung und Anwendernutzen Diese Wendeschneidplatte richtet sich an Fertigungsbetriebe und Lohnzerspaner, die Gusseisen effizient fräsen wollen. Die Ausführung F und die Toleranzklasse H unterstützen präzise, wiederholbare Resultate bei Serienfertigung. Für Anwender bedeutet das weniger Stillstand, planbare Werkzeugwechsel und eine bessere Wirtschaftlichkeit pro bearbeitetes Bauteil. Einfache Auswahl und Integration in den Fertigungsprozess Die Platte ist Teil der Tiger·tec Gold Baureihe und lässt sich in bestehende Fräswerkzeugkonzepte einbinden, sofern die Werkzeugaufnahme indexierbare Wendeschneidplatten mit Plattengröße 09 unterstützt. Technische Beratung und Schnittdatenempfehlungen helfen, die optimale Kombination aus Schnittstelle, Schnittgeschwindigkeit und Vorschub zu finden, damit die Vorteile der Sorte voll zum Tragen kommen. Empfehlung: Die WKK25G-Sorte aus der Tiger·tec Gold Serie bietet eine wirtschaftliche Lösung für das Gussfräsen — Bestellung und technische Beratung über Metav Werkzeuge, eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Produktmerkmale Artikelnummer: XNHF0906ANN-D27-WKK25G-WALTER Marke: Walter Tools Baureihe: Tiger·tec Gold Bezeichnung: XNHF0906ANN-D27 WKK25G Fakten Plattendicke: 06 Plattengröße: 09 Freiwinkel: 0° (negativ) Toleranzklasse: H Besonderheiten Sorte: WKK25G — beschichtetes Hartmetall Beschichtung: Tiger·tec Gold — Beschichtungstechnologie Spanbrecher: D27 Ausführung: F Materialanwendung: K — Gusseisen (abrasiver Verschleiß, kurze brechende Späne) Produktart: Fräswendeschneidplatte FAQ Für welche Werkstoffe ist die Platte geeignet? Die Platte ist primär für Gusseisen ausgelegt; die WKK25G-Sorte und die Tiger·tec Gold-Beschichtung sind auf abrasiven Verschleiß und brechende Späne abgestimmt. Was bedeutet der negative Freiwinkel 0° für den Einsatz? Ein negativer Freiwinkel von 0° erhöht die Stabilität der Schneidkante und eignet sich für robuste Schlicht- und Schruppaufgaben unter schwankenden Schnittbedingungen. Welche Rolle spielt der Spanbrecher D27? Der Spanbrecher D27 formt kurze Späne, verbessert die Spanabfuhr und reduziert die Gefahr von Wickelbildung, besonders bei bruchfreudigen Gusswerkstoffen. Wie unterscheidet sich WKK25G von anderen Sorten? WKK25G ist eine Walter-Sorte im Tiger·tec Gold-Programm; sie bietet beschichtetes Hartmetall mit Fokus auf Verschleißfestigkeit und breite Gussabdeckung. Wie lässt sich die Platte in den Produktionsprozess integrieren? Die Platte passt in Systeme für indexierbare Wendeschneidplatten der Größe 09. Für optimale Schnittdaten empfiehlt sich die Abstimmung mit dem Werkzeughalter und die Konsultation technischer Empfehlungen. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
XNHF0906ANN-D27 WPP35G WPP35G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating and the WPP35G grade for consistent steel machining performance; the insert’s D27 chipbreaker and 0° negative rake deliver stable chip control and reliable tool life. Order the XNHF0906ANN-D27 directly via Metav Werkzeuge or contact our advisors for application support. XNHF0906ANN-D27 WPP35G milling indexable insert — Tiger·tec Gold grade for steel | Walter Tools The XNHF0906ANN-D27 WPP35G is a coated carbide milling insert engineered for efficient and predictable machining of steel, combining Tiger·tec Gold coating technology with a dedicated chipbreaker for consistent chip formation and process security. Tiger·tec Gold coating for extended tool life WPP35G grade for reliable steel machining D27 chipbreaker for stable chip control 0° negative rake for robust cutting performance Higher productivity through controlled chip formation The Tiger·tec Gold technology and the WPP35G grade are designed to raise process stability when machining steels. The coated carbide substrate combined with the D27 chipbreaker produces short, uniform chips that reduce the risk of recuts and machine stoppages; this translates directly into higher spindle time and improved overall equipment effectiveness. The coating reduces adhesive wear and helps maintain a sharp cutting edge for longer intervals, which lowers tooling costs per component and supports predictable cycle times. Robust geometry for repeatable machining results A 0° negative rake and the chosen insert geometry deliver a robust cutting edge that resists chipping under interrupted cuts and heavy engagement. Negative rake geometry increases edge strength, which is particularly advantageous in medium- to heavy-duty milling operations in steels. The result is a stable cutting process with fewer unplanned tool changes. For pragmatic shopfloor planning, this means more consistent surface finishes and reduced machine downtime, supporting lean production targets. Practical application guidance and material fit Specified for ISO group P, the insert is optimised for unalloyed and alloyed steel where a balance of wear resistance and toughness is required. The coated grade offers a compromise between abrasion resistance and fracture toughness, making it suitable for a range of operations from semi-roughing to finishing when tool path and parameters are set accordingly. Toolholders compatible with the XNHF0906ANN-D27 geometry will benefit from the insert’s predictable load behaviour, simplifying process parameter selection and trial runs. For process integration and parameter recommendations, consult technical advisors or Metav Werkzeuge’s support documentation. Contact Metav Werkzeuge today for tailored application advice on the Walter Tools XNHF0906ANN-D27 WPP35G insert and to request availability or cutting data Technical Data Article number: XNHF0906ANN-D27-WPP35G-WALTER SKU: XNHF0906ANN-D27-WPP35G-WALTER Product type: Fräswendeschneidplatte / milling indexable insert Brand: Walter Tools Grade: WPP35G Facts Series: Tiger·tec Gold Chipbreaker: D27 Rake angle: 0° (negative) Plate size: 09 Thickness designation: 06 Tolerance class: H Special features Coated carbide (Tiger·tec Gold) Optimised for steel (ISO P) Robust edge geometry for interrupted cuts Balanced wear resistance and toughness Suitable for productive machining strategies FAQ What materials is this insert suitable for? The XNHF0906ANN-D27 WPP35G is engineered primarily for machining steel (ISO P); the WPP35G grade and Tiger·tec Gold coating optimise performance for a broad range of unalloyed and alloyed steels. How does the D27 chipbreaker affect machining? The D27 chipbreaker on this Walter Tools insert promotes controlled, broken chips that improve evacuation and reduce the risk of entanglement, supporting stable cutting conditions and consistent surface results. What does a 0° negative rake mean for cutting performance? A 0° negative rake increases edge strength and fracture resistance; in practice, the geometry offers greater robustness during heavy engagement and interrupted cuts, improving process security. Can the XNHF0906ANN-D27 WPP35G be used for finishing operations? Yes—while optimised for productive steel machining, the coated grade and insert geometry can deliver acceptable finishes in finishing passes when parameters are appropriately reduced. Where to obtain cutting data and application support? Cutting parameters and application guidance are available from Metav Werkzeuge and Walter Tools; for specific setups, Metav Werkzeuge can advise on feeds, speeds and holder choices. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany — The Walter AG (brand appearance: Walter Tools) is among the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are owned by their respective holders. The named manufacturer is referenced solely for explanation; no affiliation with the seller is implied.
XNHF0906ANN-D57 WKK25G WKK25G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and a dedicated WKK25G grade for reliable, high‑productivity machining of cast iron; the D57 chipbreaker and negative 0° geometry ensure controlled chips and robust cutting. Order directly via Metav Werkzeuge or consult the specialists for selection and logistics. XNHF0906ANN-D57 WKK25G milling insert — Tiger‑tec Gold coating, chipbreaker D57, for cast iron | Walter Tools The XNHF0906ANN-D57 WKK25G is a negative‑rake milling insert from the Tiger‑tec Gold family, designed for productive machining of abrasive cast iron components in demanding industrial operations. Tiger‑tec Gold coating for extended tool life Negative 0° geometry for robust cutting action Chipbreaker D57 for controlled chip formation Size 09 × thickness 06 for stable mounting Consistent productivity through tailored grade and coating The combination of the WKK25G grade and Tiger‑tec Gold coating targets the abrasive wear typical of cast iron, delivering a longer effective lifetime than uncoated alternatives. The coated carbide microstructure provides a balance between wear resistance and toughness, which translates into fewer insert changes and reduced downtime. For production environments that require repeatable performance, this translates into measurable gains in throughput and process stability. Safer machining with controlled chips and robust edge geometry The specified D57 chipbreaker is engineered to produce short, manageable chips when machining cast iron; this improves evacuation and reduces risk to fixtures and operators. Combined with the negative 0° rake, the geometry supports a strong cutting edge that withstands intermittent cuts and interrupted machining. In practice, this means fewer edge failures and a lower likelihood of unscheduled tool changes, enhancing both safety and efficiency on the shop floor. Stable clamping and dimensional reliability for repeatable results The insert format 09 with thickness 06 and tolerance class H offers secure seating and minimal axial deflection during heavy cuts. The robust form factor contributes to consistent surface finish and repeatable part geometry across batch runs. Where fixture repeatability and toolholder stiffness are constraints, using an insert with these dimensional characteristics helps maintain cycle‑to‑cycle accuracy and reduces rework. Application focus: engineered for cast iron components Marked for material group K, this insert is optimised specifically for cast iron machining: it copes with abrasive inclusions and the short, brittle chips typical of such materials. The grade selection emphasises wear resistance while preserving sufficient toughness for interrupted cuts. For engineers and process planners, the result is a dependable solution for finishing and semi‑finishing cast iron parts with improved tool life and consistent surface integrity. For tool procurement and process consultation on Walter Tools Tiger‑tec Gold inserts, contact Metav Werkzeuge to discuss suitable grades and delivery options via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: XNHF0906ANN-D57-WKK25G-WALTER Label: Fräswendeschneidplatte XNHF0906ANN-D57 WKK25G Walter Tools Product type: Fräswendeschneidplatte Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WKK25G Facts Plate size: 09 Plate thickness: 06 Chipbreaker: D57 Free angle: 0° (negative) Tolerance class: H Execution: F SKU: XNHF0906ANN-D57-WKK25G-WALTER Special features Material group suitability: K (cast iron) Sort description: WKK25G is a coated carbide grade within Tiger·tec Gold Typical use: machining of cast iron with abrasive wear and short chips Design focus: stable edge, optimised chip control FAQ What materials is this insert suited to? The insert is designated for material group K, which means the XNHF0906ANN-D57 WKK25G is specifically suited to machining cast iron and is optimised for abrasive wear and short chips. How does the D57 chipbreaker affect machining? The D57 chipbreaker produces short, controlled chips in cast iron machining, improving chip evacuation and reducing the risk of entanglement and toolholder damage when using the Walter Tools insert. Is the geometry suitable for interrupted cuts? Yes; the negative 0° rake and robust edge preparation provide increased mechanical strength, making the insert appropriate for interrupted or heavy engagement conditions. What production benefits can be expected from Tiger‑tec Gold? The Tiger‑tec Gold coating enhances wear resistance and prolongs tool life on abrasive cast iron, leading to fewer tool changes and improved process uptime with the Walter Tools grade WKK25G. Which size and thickness does this insert use and why does that matter? This format is 09 with thickness 06, offering secure clamping and reduced deflection for stable machining and repeatable component quality. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned solely for explanatory purposes and do not imply any affiliation with our company. The offered article is an original, factory‑new product of the named manufacturer.
XNHF0906ANN-D57 WKP25S Wendeplatten - Walter Tools
Take advantage of a proven combination of high process security and long tool life thanks to the Tiger‑tec Silver coating and the WKP25S grade; built for productive milling of steel and cast iron and optimised chip control—order directly via Metav Werkzeuge or contact our consultants for application advice. XNHF0906ANN-D57 WKP25S — milling indexable insert with Tiger‑tec Silver coating for steel and cast iron | Walter Tools A XNHF0906ANN-D57 WKP25S milling indexable insert engineered for heavy-duty and reliable machining of steel (P) and cast iron (K) with a negative 0° rake angle for predictable cutting behaviour Tiger‑tec Silver coated for wear resistance WKP25S grade for steel and cast iron machining Negative 0° rake for stable cutting forces Chipbreaker D57 for controlled swarf removal Higher productivity through advanced coating and grade The combination of the Tiger‑tec Silver coating with the WKP25S cemented carbide grade delivers a measurable increase in process security and tool life when machining steels and grey or nodular cast irons. The coating reduces abrasive wear and thermal impact on the cutting edge, which translates into fewer tool changes and longer uninterrupted production cycles. For industrial shops aiming to reduce cycle times, this insert offers a reliable balance between edge stability and toughness, making it suitable for both roughing and medium‑finishing operations. Consistent chip control and dimensional stability Built around the chipbreaker D57 geometry and a negative 0° rake, the insert secures consistent swarf formation and evacuation under the thermal and mechanical loads typical of steel and cast iron. The stable cutting edge geometry helps to maintain component tolerances and surface finish over longer tool life, reducing rework and inspection overhead. The insert’s tolerance class H supports predictable clamping and repeatable positioning in modular milling holders, which benefits automated production and high‑volume batches. Seamless integration into production workflows With an insert size designation of 09 and thickness 06, this indexable plate fits established milling tool systems and supports quick index changes to restore cutting performance. The coated cemented carbide substrate is optimised for industrial machining strategies where consistent results and low variance are essential. Using these inserts in standard milling modules enables a clear calculation of cost per edge and helps to plan maintenance cycles. Technical teams will appreciate the straightforward material classification (P / K) aligning with ISO 513 groups for selecting cutting data. For expert technical advice on applying Walter Tools’ Tiger‑tec Silver inserts in specific milling operations, contact Metav Werkzeuge for availability and cutting‑data support at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: XNHF0906ANN-D57-WKP25S-WALTER Designation: XNHF0906ANN-D57 ISO designation: XNHF0906ANN-D57 WKP25S Product type: Milling indexable insert Series: Tiger‑tec Silver Grade: WKP25S Material: Coated cemented carbide (P / K) Execution: F Core measurements Insert size: 09 Thickness: 06 Rake angle: 0° (negative) Tolerance class: H Special features Chipbreaker: D57 Optimised for: Steel (P) and cast iron (K) Coating: Tiger‑tec Silver Main application: Productive milling with stable swarf control FAQ What materials is this insert suitable for? The XNHF0906ANN-D57 WKP25S insert is specified for ISO groups P (steel) and K (cast iron) and is designed to cope with the thermal and abrasive demands of these materials. How does the Tiger‑tec Silver coating benefit machining? The Tiger‑tec Silver coating on the WKP25S grade reduces abrasive wear and improves heat resistance, resulting in longer edge life and fewer tool changes in steel and cast‑iron milling. What does the negative 0° rake mean in practice? A negative 0° rake gives a robust cutting edge and stabilises cutting forces, which helps when milling rough or interrupted cuts and supports dimensional consistency during heavy engagement. Is the chipbreaker D57 suitable for finishing operations? The D57 chipbreaker is optimised for controlled swarf formation and evacuation; while primarily effective in moderate to heavy cuts, it also supports finishing passes when cutting parameters are adjusted accordingly. Which toolholders are compatible with this insert size and thickness? Insert size 09 and thickness 06 conform to common modular milling holders; compatibility should be checked against the specific toolholder catalogue, ensuring correct seat and clamp geometry for the XNHF0906ANN‑D57 plate. Manufacturer: Walter Tools; Headquarters: Tübingen, Germany Protected trademarks and product names are the property of their respective owners and are mentioned for explanation only. There is no affiliation between our company and the trademark owners. The offered item is original, factory‑new merchandise of the manufacturer. The Walter AG (brand appearance: Walter Tools) is headquartered in Tübingen and is part of the Sandvik Group.
XNHF0906ANN-D57 WKP35G Wendeplatten - Walter Tools
Combining the Tiger·tec Gold coating with the WKP35G grade, this indexable milling insert delivers a robust balance of wear resistance and edge stability for machining steel and cast iron; its D57 chipbreaker and 0° negative rake support controlled chip formation and reliable material removal. Order directly via Metav Werkzeuge or consult their application specialists for tailored recommendations. XNHF0906ANN-D57 WKP35G milling insert – Tiger·tec Gold coated, for steel & cast iron (Walter Tools) The XNHF0906ANN-D57 WKP35G is an indexable milling insert designed for productive cutting of steel and cast iron, combining a coated carbide substrate with a chipbreaker geometry for consistent chip control and extended tool life Tiger·tec Gold coating for wear resistance WKP35G grade for edge stability 0° negative rake for heavy cuts D57 chipbreaker for controlled chips Increased material removal with predictable tool life The insert’s Tiger·tec Gold technology pairs a hard, wear-resistant coating with a tough substrate to reduce flank wear while preserving edge stability. The WKP35G grade is optimised for the heat and chip behaviour typical when machining steel and cast iron, which results in longer intervals between indexings and fewer tool swaps. With a neutral 0° rake, the geometry is suited to interrupted cuts and machine-tool set-ups where edge robustness is prioritised over extreme cutting lightness. The net benefit is a more predictable tool life and reduced process interruptions, supporting leaner production cycles and stable output. Stable surface quality and controlled chip formation A well-matched chipbreaker is central to secure metal removal; the D57 chipbreaker on this insert shapes chips to prevent tangling and to ease evacuation from the cut. The 0° negative rake further enhances the cutting edge’s mechanical strength, which helps maintain a consistent cutting geometry under heavier feed or depth-of-cut conditions. For milling operations where repeatable surface finish and dimensional consistency matter, the combination of chip control and edge stability reduces the need for reworking and supports higher first-pass yields. The insert’s design therefore contributes directly to process security and predictable component quality. Geometry and application guidance for reliable integration Key dimensional and tolerance features support straightforward integration into established cutter bodies: the insert is supplied in plate size 09 with a thickness of 06 and tolerance class H, in execution F. The marking P / K indicates suitability for machining steel (P) and cast iron (K) according to ISO material groupings, enabling selection of a single grade for mixed-production environments. Indexable insert users will recognise the value of a well-documented grade and chipbreaker combination when matching cutter bodies and selecting initial cutting parameters. For component-specific settings or to verify compatibility with a particular holder or machine, Metav Werkzeuge’s technical advisors can provide geometry-matching guidance and recommendations. Contact Metav Werkzeuge for tailored application advice and genuine Walter Tools inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 for specification support and to confirm suitability for specific machining tasks Technical data SKU: XNHF0906ANN-D57-WKP35G-WALTER Article designation: XNHF0906ANN-D57 WKP35G Product type: milling insert Manufacturer: Walter Tools Core specifications Grade: WKP35G Series: Tiger·tec Gold Rake angle: 0° (negative) Chipbreaker: D57 Plate size: 09 Thickness: 06 Tolerance class: H Execution: F Material suitability: P / K (steel and cast iron) Special features Coated carbide cutting material Optimised for steel and cast iron machining Indexable insert for milling operations Stable edge for interrupted cuts FAQ What materials is this insert best suited for? The XNHF0906ANN-D57 WKP35G insert is designed for machining steel and cast iron, as indicated by the P / K designation and the WKP35G grade formulation. How does the Tiger·tec Gold coating benefit machining? Tiger·tec Gold provides wear resistance and thermal stability, helping the insert maintain a sharp cutting edge longer and supporting sustained material removal rates. What is the function of the D57 chipbreaker? The D57 chipbreaker controls chip shape to facilitate evacuation and reduce the risk of chip entanglement, which contributes to consistent surface quality and safer operation. Is the 0° negative rake suitable for interrupted cuts? Yes; the 0° negative rake increases the mechanical strength of the cutting edge, making the insert well suited to interrupted or heavy-engagement milling conditions. Which specifications are important when matching the insert to a cutter body? Plate size (09), thickness (06), tolerance class (H) and the ISO designation XNHF0906ANN-D57 WKP35G should be checked to ensure correct seating and clamping in the chosen cutter body Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
XNHX0705ANN-D67 WHH15X Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide WHH15X, D67 chipbreaker and 0° negative rake for stable chip control and reliable tool life; order the insert directly via Metav Werkzeuge or consult the experts for selection support. XNHX0705ANN-D67 WHH15X milling indexable insert — coated carbide, D67 chipbreaker A high-performance milling indexable insert designed for general machining where reliable chip control and consistent cutting-edge behaviour are required. Coated carbide WHH15X for wide material range 0° negative rake for robust cutting conditions D67 chipbreaker for controlled chip formation Plate size 07 with thickness 05 for standard toolholders Stable chip control and longer tool life for productive turning and milling The insert is engineered around a coated carbide grade that promotes stable chip formation and dependable wear resistance. The D67 chipbreaker geometry reduces long chips and supports predictable evacuation, which lowers downtime for manual chip clearing and improves process stability. By combining a 0° negative rake with a coated substrate, the design permits secure engagement in interrupted cuts and heavier axial depths, translating into fewer indexings and a steadier part finish. Consistent performance across common machining tasks The open-series WHH15X cutting grade is suitable as a versatile solution when material specifics vary; the exact workpiece compatibility should be verified against the product matrix. The coating and substrate pairing provides a balance between toughness and wear resistance, which is particularly helpful when switching between castings, non-alloy steels and mixed batches. This balance supports repeated, reproducible results and reduces the need for frequent insert changes in medium-demand production runs. Practical handling and integration for workshop efficiency With a standard plate designation and modest profile dimensions, the insert integrates into common milling cutter systems without special adapters. The clearly defined plate size 07 and thickness 05 simplify tooling logistics and stock management. The negative rake helps to preserve the cutting edge under heavy contact, while the chipbreaker lowers the risk of tool-related interruptions, contributing to smoother downstream processes and easier maintenance scheduling. Contact Metav Werkzeuge for tailored application advice on Walter Tools WHH15X inserts and assistance with cutter selection to match specific machining tasks Technical data Article number: XNHX0705ANN-D67-WHH15X-WALTER SKU: XNHX0705ANN-D67-WHH15X-WALTER Item designation: XNHX0705ANN-D67 WHH15X Facts Plate size: 07 Plate thickness: 05 Rake angle: 0° (negative) Tolerance class: H Special features Series: Walter Schneidstoffsorte - Serie offen Grade: WHH15X (coated carbide) Chipbreaker: D67 Execution: X Material designation: catalogue-dependent FAQ What applications is this insert suitable for? The XNHX0705ANN-D67 WHH15X milling indexable insert is intended for general milling operations where coated carbide performance and reliable chip control are required; compatibility with specific workpiece materials should be checked against the product matrix. How does the D67 chipbreaker improve machining? The D67 chipbreaker is designed to produce shorter, controlled chips, enhancing evacuation and reducing interruptions; when paired with the WHH15X grade, it contributes to consistent surface quality and extended edge life. Is the 0° negative rake suitable for heavy cuts? Yes, the 0° (negative) rake increases edge strength and stability under heavier engagement, making the insert appropriate for interrupted cuts and tougher machining conditions. Which cutter holders accept plate size 07 inserts? Standard milling cutter systems that are specified for plate size 07 accept this insert; verify holder compatibility with the insert designation XNHX0705ANN-D67. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
XNHX0906ANN-D67 WHH15X Wendeplatten - Walter Tools
Take advantage of a coated carbide grade that combines consistent chip control and a robust cutting edge; the D67 chipbreaker and 0° (negative) relief angle ensure secure milling performance and longer tool life. Order genuine Walter Tools inserts or consult Metav Werkzeuge for application support and availability. XNHX0906ANN-D67 WHH15X milling indexable insert — 0° (negative) relief, D67 chipbreaker (Walter Tools) The XNHX0906ANN-D67 WHH15X is a coated carbide milling insert engineered for stable cutting in demanding industrial milling operations, offering reliable chip control and secure edge integrity for a wide range of workpiece materials. Coated carbide grade WHH15X Negative relief 0° for strong cutting edge D67 chipbreaker for consistent chip control Size 09, thickness 06 for stable seating Precision chip control for uninterrupted productivity The coated carbide WHH15X grade and the D67 chipbreaker work together to provide predictable chip control and reduced re-cutting of swarf, which improves surface finish and lowers cycle times. The insert’s chipformer geometry is designed to break and evacuate chips effectively in interrupted and continuous milling. For workshops prioritising throughput, this combination translates into fewer tool changes and more consistent process results. The construction as a coated carbide indexable insert offers wear resistance that supports repeatable performance across batches, while the open-series manufacturing approach gives flexibility in selecting the correct grade for specific machining tasks. Secure seating and edge strength for heavy-duty milling With a 0° (negative) relief angle the insert presents a more robust cutting edge, improving resistance to chipping during heavy engagement and interrupted cuts. The format Size 09 with 06 thickness and tolerance H provides a solid contact area in the pocket, reducing vibration and improving dimensional stability during aggressive milling. These geometric choices favour operators who require mechanical robustness and repeatable clamping behaviour; the result is improved tool life and fewer set-up interruptions, which in turn supports steady production flow and predictable machining costs. Cost-conscious productivity with process reliability The grade’s coating and substrate combination aims to deliver stable wear behaviour and consistent results across shifting production conditions, helping to reduce scrap and downstream rework. The insert’s specification supports a rational cost-benefit assessment: fewer interventions at the machine, predictable surface quality and a durable cutting edge lower the total cost per manufactured part. For engineers planning process windows, the insert should be selected against a material–cutting data matrix to ensure optimum cutting speeds and feeds; this step secures both performance and economy in serial production. Compatibility guidance and practical application notes This insert is supplied in the Walter Tools WHH15X coated carbide family and is intended for general milling duties; compatibility with specific workpiece materials should be verified using the manufacturer’s product matrix. The D67 chipbreaker suits a range of chip thicknesses and milling strategies, but optimal results depend on correct seat clamping, appropriate feed per tooth and coolant strategy. Where operations involve highly abrasive or unusually hard materials, a targeted grade selection based on the process matrix is advisable to maintain surface integrity and tool life. For tailored cutting recommendations or to obtain original Walter Tools XNHX0906ANN-D67 WHH15X inserts for production, contact Metav Werkzeuge for expert advice and fast supply coordination Technical data SKU: XNHX0906ANN-D67-WHH15X-WALTER Designation: XNHX0906ANN-D67 WHH15X Product type: Fräswendeschneidplatte (milling indexable insert) Manufacturer: Walter Tools Numbers / Core data Relief angle: 0° (negative) Chipbreaker: D67 Size: 09 Thickness: 06 Tolerance class: H Special features Coated carbide grade WHH15X Series: Walter cutting-grade — open series Geometry/execution: X Material specification: catalogue-dependent FAQ What materials is this insert suitable for? Suitability depends on the specific workpiece and cutting parameters; the WHH15X coated carbide insert is designed for a broad range of applications but material compatibility should be checked in the Walter Tools product matrix for optimal cutting data. How does the 0° (negative) relief affect performance? A 0° (negative) relief increases edge robustness and resistance to chipping, making the insert suitable for interrupted cuts and heavy engagements where a strong cutting edge is required. Can the D67 chipbreaker be used for finishing operations? The D67 chipbreaker is optimised for controlled chip formation and evacuation; finishing performance will depend on feed, speed and clamping stability, but it supports improved surface quality when properly applied. Is this an original Walter Tools product? This is an original Walter Tools cutting insert in the WHH15X coated carbide family, supplied as specified by the manufacturer for industrial milling operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected designations are cited solely for explanation; there is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
XNHX130608R-L65T WSM45X WSM45X Wendeplatten - Walter Tools
Combining the WSM45X coated carbide grade with a 0° negative rake and an L65T chipbreaker, this insert provides stable chip formation and edge security when machining stainless steel and heat‑resistant superalloys. Order the insert directly via Metav Werkzeuge or consult our specialists for material‑specific machining data. XNHX130608R-L65T WSM45X — Milling indexable insert, 0° negative rake (Walter Tools) The XNHX130608R-L65T WSM45X is a precision milling insert engineered for demanding operations on stainless steel and high‑temperature alloys, offering reliable edge life and controlled chip flow WSM45X coated carbide grade 0° negative rake for stable cutting 0.8 mm corner radius for secure edge Optimised L65T chipbreaker Consistent performance on demanding materials The combination of the WSM45X coated carbide and the L65T chipbreaker delivers a dependable balance between wear resistance and chip control when machining tough alloys. The coated substrate is formulated to tolerate the thermal and mechanical stresses typical of stainless steel and heat‑resistant superalloys, so tool life is extended and unexpected downtime is reduced. By using an insert with a 0° negative rake, the cutting edge is stabilised under heavy loads, which supports predictable dimensional results and minimises the frequency of insert changes during production runs. Improved process security and machining economy A 0.8 mm corner radius and robust insert geometry translate into higher process security for interrupted cuts and varying depths of engagement. The geometry reduces the risk of chipping and supports stable cutting forces, which is particularly advantageous in roughing passes and semi‑finishing of less machinable materials. Together, the coated grade and geometry help achieve a favourable cost‑per‑part through longer edge life and fewer tool changes. For operations that prioritise productivity and repeatability, this insert is optimised to contribute to more consistent cycle times and surface integrity. Practical handling, application scope and recommendations The insert is supplied in the ISO designation XNHX130608R-L65T WSM45X and is compatible with common milling toolholders designed for indexable inserts of this form. Its specification suits applications in the M and S ISO groups, meaning stainless steel and heat‑resistant superalloys and titanium alloys where thermal resistance and secure chip formation are required. For selection and parameter tuning, consider modest ap and ae values in initial trials and increase feed cautiously while monitoring tool condition; the combination of WSM45X and the L65T chipbreaker supports gradual optimisation without sacrificing edge stability. For application advice or to secure this Walter Tools insert for demanding stainless steel and superalloy machining, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: XNHX130608R-L65T-WSM45X-WALTER Product designation: XNHX130608R-L65T WSM45X Type: Milling indexable insert Brand: Walter Tools Core specifications Plate size: 13 mm Thickness designation: 06 Corner radius: 0.8 mm Relief angle: 0° (negative) Tolerance class: H Features & suitability Coated carbide grade WSM45X Chipbreaker type L65T Geometry designation: X, execution: X Series: Walter Schneidstoffsorte - Serie offen Suitable for stainless steel (ISO group M) and heat‑resistant superalloys/titanium (ISO group S) FAQ What materials is this insert intended for? The XNHX130608R-L65T WSM45X insert is designed for stainless steel (ISO group M) and heat‑resistant superalloys and titanium (ISO group S), where thermal stability and secure chip formation are required. What does the 0° negative rake mean for cutting behaviour? A 0° negative rake provides a stronger cutting edge and improved resistance to chipping under heavy loads; the XNHX130608R-L65T WSM45X benefits from this geometry when used in interrupted or heavy cuts. How does the L65T chipbreaker affect machining? The L65T chipbreaker is optimised to produce short, controlled chips in tougher materials, promoting safe chip evacuation and consistent cutting forces with the WSM45X grade. Is the corner radius suitable for roughing operations? Yes, the 0.8 mm corner radius offers enhanced edge strength, making the insert appropriate for roughing and semi‑finishing where a robust cutting edge is needed. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
XNHX130608R-L65T WSP45G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold PVD coating and the WSP45G grade for extended tool life and stable chip formation; with a 0° negative rake and a 0.8 mm corner radius this insert supports consistent milling results — order directly via Metav Werkzeuge or consult our technical advisers for application-specific recommendations. XNHX130608R-L65G — XNHX130608R-L65T WSP45G milling indexable insert by Walter Tools, Tiger·tec Gold PVD, chipbreaker L65T The XNHX130608R-L65T WSP45G is a milling indexable insert designed for productive milling across steel, stainless steel and heat‑resistant superalloys, offering a robust, coated‑carbide grade for demanding shop‑floor tasks. Tiger·tec Gold PVD coating Suitable for steel, stainless and superalloys 0° negative rake for stable cutting Corner radius 0.8 mm for precision Lower machining costs through durable coating and predictable performance The Tiger·tec Gold PVD technology delivers a coated carbide surface that reduces wear and supports longer tool life. The WSP45G grade is designed to maintain a stable cutting edge under the thermal and mechanical stresses typical of milling, which results in fewer index changes and lower tooling costs per workpiece. In combination with the chipbreaker L65T, the insert encourages controlled chip formation and evacuation, reducing the risk of edge build‑up and unplanned stoppages. This reliability translates into improved process efficiency and a measurable contribution to production economics. Confident machining of a wide material range with stable cutting geometry The insert is engineered for the ISO material groups P, M and S — that is, steel, stainless steel and superalloys/titanium — giving versatility across mixed production batches. The 0° negative rake increases edge stability when taking heavier cuts or when interrupted cuts occur, while the 0.8 mm corner radius balances edge strength with surface finish capability. For shops working with challenging alloys, these design choices help avoid premature flank wear and support consistent component tolerances, even under elevated temperatures and poor thermal conductivity of the workpiece material. Repeatable fit and shop‑floor reliability for series production Designed to established tolerances, the insert’s tolerance class H and the clear plate designation ensure repeatable seating in toolholders and predictable clamping behaviour. The inscribed circle of 13 mm and the thickness code 06 correspond to commonly used toolholder systems, simplifying tool inventory and changeover. Predictable geometry and standardised dimensions reduce setup time and help maintain machining stability across shifts. Together, these attributes support high uptime and consistent part quality in serial milling operations. For tailored application advice on Walter Tools Tiger·tec Gold inserts and to arrange supply from Metav Werkzeuge, contact our specialists at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt support and technical guidance. Technical Data Article number: XNHX130608R-L65T-WSP45G-WALTER Name: Fräswendeschneidplatte XNHX130608R-L65T WSP45G Manufacturer: Walter Tools Facts Inscribed circle: 13 mm Corner radius: 0.8 mm Free rake angle: 0° (negative) Thickness code: 06 Tolerance class: H Special features Grade: WSP45G (Tiger·tec Gold, PVD) Chipbreaker: L65T Material suitability: Steel (P), Stainless steel (M), Superalloys/Titanium (S) Plate designation: XNHX130608R-L65T Series: Tiger·tec Gold FAQ What materials is this insert suitable for? The XNHX130608R-L65T WSP45G insert is suitable for steel, stainless steel and superalloys/titanium (ISO groups P, M, S), thanks to the WSP45G PVD‑coated carbide grade. How does the chipbreaker L65T affect milling performance? The L65T chipbreaker on the XNHX130608R-L65T promotes controlled chip formation and evacuation, which improves surface integrity and reduces the risk of built‑up edge during continuous and interrupted milling. What does the 0° (negative) rake angle mean for cutting? A 0° negative rake provides increased edge strength and stability under heavy or interrupted cuts, helping to protect the cutting edge and supporting consistent tool life in demanding milling operations. Which toolholder dimensions match this insert? This insert uses an inscribed circle of 13 mm and thickness code 06, matching standard toolholder pockets for the corresponding plate designation XNHX130608R-L65T. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned only for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is an original, brand‑new product from Walter Tools.
XNHX130608R-L65W WSM45X WSM45X Wendeplatten - Walter Tools
Benefit from the combination of Walter Tools’ WSM45X coated carbide and the L65W chipbreaker for reliable machining of stainless steels and heat‑resistant superalloys; the 0° negative rake and 0.8 corner radius deliver stable cutting edges and predictable tool life. Order directly via Metav Werkzeuge or consult our technical advisors for tailored cutting data. XNHX130608R-L65W WSM45X milling insert — Walter Tools — 0° negative rake, 0.8 radius A XNHX130608R-L65X WSM45X milling insert engineered for heavy‑duty machining of stainless steels and heat‑resistant superalloys with a robust L65W chipbreaker. Walter WSM45X coated carbide grade L65W chipbreaker for stable chip control 0° negative rake for edge stability Optimised for tough materials and reproducible performance The combination of the WSM45X coating and a well‑balanced substrate provides a rational improvement in process security when machining challenging materials. Designed specifically for the demands of stainless steels (M) and heat‑resistant superalloys and titanium alloys (S), this insert supports secure chip formation and resists edge wear under high thermal load. The L65W chipbreaker promotes consistent chip shape, which reduces rework time and helps maintain stable cutting forces during extended runs. Durable edge geometry for longer tool life and surface quality A 0° negative rake paired with a 0.8 corner radius enhances edge strength and reduces the risk of chipping when plunging or interrupted cutting occurs. The robust geometry and the H tolerance class combine to deliver repeatable mounting accuracy and consistent surface results across batches. The result is fewer tool changes, lower scrap rates and a measurable increase in productivity in serial and batch production environments. Practical integration into milling operations and holder compatibility The insert’s designation and dimensions make it straightforward to match to standard milling cutters and clamping systems used in metalworking shops. Its configuration supports a range of cutter designs where stable chip control and thermal resistance are priorities. For specific cutting speeds, feeds and coolant strategies for particular alloys, consult Metav Werkzeuge’s application engineers or request cutting data to align the insert with the chosen toolholder and machine capability. Contact Metav Werkzeuge for a technical consultation on Walter Tools’ XNHX130608R-L65W WSM45X milling insert and to obtain recommended cutting data: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: XNHX130608R-L65W-WSM45X-WALTER Product: Fräswendeschneidplatte (milling insert) Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Grade: WSM45X Version: X Numbers / Core technical data Insert size: 13 Thickness: 06 Corner radius: 0.8 Rake angle: 0° (negative) Tolerance class: H Designs / Special features Chipbreaker: L65W Coating/substrate: coated carbide (WSM45X) Material suitability: S / M Typical applications: stainless steels and heat‑resistant superalloys FAQ What materials is this insert suitable for? The XNHX130608R-L65W WSM45X insert by Walter Tools is suitable for stainless steels (M) and heat‑resistant superalloys/titanium (S), offering secure chip formation in these groups. How does the L65W chipbreaker improve machining? The L65W chipbreaker on the Walter Tools insert shapes chips reliably and promotes stable evacuation, which reduces heat concentration at the cutting zone and supports consistent surface quality. Is the 0° negative rake suitable for heavy machining? Yes, the 0° negative rake increases edge robustness for interrupted cuts and heavy engagement, contributing to longer service life under demanding conditions. What does the WSM45X designation mean for performance? WSM45X denotes a coated carbide grade optimised for thermal stability and wear resistance when machining difficult‑to‑cut materials; it balances hardness and toughness for repeatable performance. How to obtain cutting data for specific workpieces? Request tailored cutting parameters from Metav Werkzeuge; they can recommend speeds, feeds and coolant strategies for the XNHX130608R-L65W WSM45X insert based on the workpiece material and machine. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools), headquartered in Tübingen, is among the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and product names are the property of their respective owners. The mentioned brand is named for explanation only; there is no affiliation between our company and the brand owner. The offered item is original and factory‑new.
XNHX130612R-L65T WSM45X Wendeplatten - Walter Tools
Take advantage of a coated carbide grade optimised for demanding materials and a chipbreaker engineered for controlled swarf formation; the result is efficient machining with reliable cutting-edge life. Order the XNHX130612R-L65T WSM45X directly via Metav Werkzeuge or ask our consultants if needed. XNHX130612R-L65X WSM45X milling indexable insert — 0° negative rake, r1.2, Walter Tools The XNHX130612R-L65T WSM45X is a coated carbide milling insert designed for machining stainless steel and heat‑resistant superalloys in demanding production environments. Coated carbide for difficult materials 0° negative rake for edge strength Corner radius 1.2 mm for robust profiles L65T chipbreaker for controlled swarf Superior edge stability for consistent machining results The combination of the WSM45X coated carbide and a 0° negative rake provides enhanced edge stability under heavy thermal and mechanical load. This results in fewer unexpected tool changes and more predictable tool life when working with stainless steel or high‑temperature alloys. The formulation of the cutting material supports secure chip formation and helps to limit built‑up edge, which translates into more consistent surface finish and dimensional accuracy across serial production. Controlled chip formation to reduce cycle interruptions The dedicated L65T chipbreaker is engineered to produce short, manageable chips in interrupted or continuous milling. Controlled swarf reduces the risk of re‑cutting and machine stoppages and helps to maintain coolant flow around the cutting zone. For workshops seeking to increase uptime and reduce manual chip handling, this geometry offers a clear process advantage and contributes to smoother, safer machining cycles. Geometry matched to hard‑to‑cut alloys and stainless steel With a corner radius of 1.2 mm, the insert balances edge strength and profile fidelity, enabling reliable profiling and shoulder milling without premature chipping. The insert’s series designation and coated hardmetal construction make it suitable for applications in which material adhesion, heat accumulation and abrasive wear are critical factors. For machinists addressing components in stainless steel or superalloy families, the insert’s specifications support stable cutting conditions and repeatable results. Practical integration and predictable series performance The insert is supplied in the XNHX130612R-L65T form, a common format for modular milling systems, facilitating straightforward toolholder compatibility. The tolerance class H and the specified series ensure consistent part interchangeability and quality across batches. For production planners and process engineers, this means quicker tool qualification and less variation in machining output when the insert is integrated into existing tool sets. For tailored technical advice or availability on Walter Tools inserts such as the WSM45X, contact Metav Werkzeuge for application consultation and immediate stock information at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical Data SKU: XNHX130612R-L65T-WSM45X-WALTER Article: Fräswendeschneidplatte XNHX130612R-L65T WSM45X Walter Tools Manufacturer: Walter Tools Designation: XNHX130612R-L65T WSM45X Core specifications Free cutting angle: 0° (negative) Corner radius: 1.2 mm Insert size: 13 mm Thickness code: 06 Tolerance class: H Special features Coated hardmetal grade: WSM45X Chipbreaker: L65T Execution code: X Series: Walter Schneidstoffsorte - Serie offen Material applicability: S / M Suitable for: stainless steel and heat‑resistant superalloys FAQ What materials is this insert suitable for? The XNHX130612R-L65T WSM45X is formulated for machining stainless steel and heat‑resistant superalloys, as indicated by its S / M material applicability. How does the 0° negative rake affect performance? A 0° negative rake increases edge strength and resistance to chipping under heavy loads; this makes the insert robust in interrupted cuts and when machining tough alloys. What benefit does the L65T chipbreaker deliver? The L65T chipbreaker promotes controlled chip formation and breakage, improving swarf control and reducing the likelihood of re‑cutting, which helps maintain surface quality. Is the corner radius suitable for profile work? With a corner radius of 1.2 mm, the insert provides a good compromise between edge strength and the ability to produce stable profiles in finishing and semi‑finishing operations. Can this insert be used in standard milling holders? The XNHX130612R form factor is compatible with common modular milling systems; tolerance class H supports consistent fit and repeatability. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
XNHX130612R-L65T WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger·tec Gold coating, robust edge geometry and reliable chip control to keep milling cycles productive and repeatable; order through Metav Werkzeuge or consult the sales team for machining data and availability. XNHX130612R-L65T WSP45G — milling insert, Tiger·tec Gold, for steel & stainless steel | Walter Tools XNHX130612R-L65G WSP45G — a versatile coated milling insert for demanding P / M / S applications Tiger·tec Gold PVD coating Versatile for steel, stainless steel and superalloys 0° negative rake for exceptional edge strength L65T chipbreaker with 1.2 mm corner radius High-efficiency machining for a wide material range The Tiger·tec Gold grade delivers a balance between wear resistance and toughness that supports consistent metal removal rates across a spectrum of workpiece materials. Designed for the machining groups P, M and S, this insert is tuned for unalloyed and alloyed steel, for stainless steel, and for heat-resistant superalloys and titanium. The combination of a PVD-coated substrate and a dedicated L65T chipbreaker promotes controlled chip formation, which reduces downtime for chip handling and improves cycle consistency on milling operations. Robust edge geometry that extends tool life A 0° negative rake angle and a 1.2 mm corner radius create a mechanically strong cutting edge that resists chipping under interrupted cuts and heavy engagement. This geometry supports secure clamping loads and helps maintain dimensional stability in serial production. The insert’s designation and thickness classification ensure compatibility with standard cutter bodies, while the coated carbide substrate provides a protective barrier against abrasive wear, leading to longer intervals between indexings and fewer tool changes. Process reliability and predictable results The coated grade is part of a series engineered for reproducible results in industrial environments. Consistent edge behaviour delivers repeatable surface quality and predictable tool life, which makes planning and cost calculation simpler for production teams. The insert’s stability during cutting increases process security, especially when machining tougher steels or workpieces with variable hardness; this contributes directly to higher overall equipment effectiveness. Simple integration into milling tool systems The insert’s ISO-style designation aligns with common holder geometries, enabling straightforward replacement and inventory handling. The L65T chipbreaker is optimised to support common feed ranges while maintaining efficient evacuation of chips. As a standardised indexable insert, it integrates easily into existing milling cutters, simplifying logistics and supporting quick turnaround during regrinds or tool swaps. Contact Metav Werkzeuge for cutting data, application advice and stock details on the Walter Tools XNHX130612R-L65T WSP45G insert Technical data Article number / SKU: XNHX130612R-L65T-WSP45G-WALTER Designation: XNHX130612R-L65T WSP45G Product type: milling insert (indexable) Brand: Walter Tools Series: Tiger·tec Gold Grade: WSP45G Core data Corner radius: 1.2 mm Free cutting angle: 0° (negative) Insert size: 13 Thickness designation: 06 Tolerance class: H Special features Coating: Tiger·tec Gold (PVD) Substrate: coated carbide Chipbreaker: L65T Material suitability: P / M / S (steel, stainless steel, superalloys & titanium) Application: general-purpose and demanding milling tasks FAQ What materials is this insert suitable for? The XNHX130612R-L65T WSP45G insert is specified for P, M and S groups — namely steels, stainless steels and heat-resistant superalloys/titanium — offering versatile performance in a wide range of milling applications. What advantage does the 0° negative rake provide? A 0° negative rake improves edge strength and resistance to chipping during heavy or interrupted cuts, contributing to longer edge life and improved process stability when using the Walter Tools insert. How does the L65T chipbreaker affect chip control? The L65T chipbreaker is designed to create short, controllable chips across common feeds, aiding evacuation and reducing re-cutting of chips, which supports consistent surface finish and safer cycling. Is the coating suitable for high-temperature cutting? The Tiger·tec Gold PVD coating enhances thermal and abrasive resistance of the coated carbide, supporting machining where elevated temperatures and wear are expected, particularly in stainless steels and superalloys. Does the insert fit standard cutter bodies? The ISO-style designation and thickness class allow straightforward mounting in compatible toolholders; verify the holder’s compatible insert geometry before assembly. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision metalworking tools and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original, brand-new goods from the manufacturer.
XNHX130616R-L65T WSM45X Wendeplatten - Walter Tools
XNHX130616R-L65T WSM45X Fräswendeschneidplatte von Walter Tools Die XNHX130616R-L65T WSM45X ist eine beschichtete Fräswendeschneidplatte für die produktive Zerspanung von rostfreien Stählen sowie hitzebeständigen Superlegierungen und Titan. Beschichtetes Hartmetall für lange Standzeit Optimierte Spanbildung durch L65T-Spanbrecher Negativer Freiwinkel 0° für stabile Schneidkante Eckradius 1,6 mm für robuste Schnitte Effiziente Schneidleistung für anspruchsvolle Werkstoffe Die WSM45X-Sorte kombiniert beschichtetes Hartmetall mit einem auf Stabilität ausgelegten Plattendesign und liefert dadurch verlässliche Ergebnisse bei der Bearbeitung von rostfreien Stählen und hitzebeständigen Legierungen. Durch die gezielte Materialwahl wird die Spanbildung kontrolliert, was Aufbauschneiden reduziert und die Prozesssicherheit erhöht. Anwender profitieren von konstanter Bearbeitungsqualität und reduzierten Stillstandszeiten. Geometrie und Nutzen für den Produktionsprozess Mit einem negativen Freiwinkel 0° (negativ), einem Eckenradius 1,6 mm und dem L65T-Spanbrecher ist die Platte auf robuste Schnittbedingungen ausgelegt. Der negative Freiwinkel stärkt die Schneidkante, wodurch Bruchrisiken bei schwer zerspanbaren Werkstoffen verringert werden. Der ausgewählte Eckradius unterstützt stabile Schnitte und verlängert die Standzeit, was sich direkt in geringeren Werkzeugkosten und höherer Maschinenlaufzeit niederschlägt. Einsatzbereiche und Zielgruppe Kernanwender sind Lohnfertiger und Produktionsbetriebe, die rostfreie Stähle sowie Superlegierungen und Titan sicher und reproduzierbar bearbeiten müssen. Die Sorte WSM45X ist speziell für solche Werkstoffe optimiert: M steht für rostfreie Stähle, S steht für hitzebeständige Superlegierungen und Titan. Für Fertigungen, die Prozesssicherheit und konstante Oberflächengüte verlangen, bietet diese Wendeschneidplatte eine praxisnahe und wirtschaftliche Lösung. Empfehlung: Die WSM45X-Sorte von Walter Tools wählen, um die Zerspanung von rostfreien Stählen zuverlässig zu sichern — Verfügbarkeit und Beratung bei Metav Werkzeuge per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: XNHX130616R-L65T-WSM45X-WALTER Bezeichnung: XNHX130616R-L65T Marke: Walter Tools Serie: Walter Schneidstoffsorte - Serie offen Sorte: WSM45X Ausführung: X Toleranzklasse: H Fakten Eckenradius: 1,6 mm Freiwinkel: 0° (negativ) Plattengröße: 13 Plattendicke: 06 Besonderheiten Material: S / M (S: hitzebeständige Superlegierungen und Titan; M: rostfreie Stähle) Schneidstoffklasse: beschichtetes Hartmetall Spanbrecher: L65T Anwendung: rostfreie Stähle FAQ Für welche Werkstoffe ist die Wendeschneidplatte geeignet? Die Wendeschneidplatte XNHX130616R-L65T WSM45X von Walter Tools ist für rostfreie Stähle sowie hitzebeständige Superlegierungen und Titan ausgelegt. Was bewirkt der negative Freiwinkel 0° in der Praxis? Der negative Freiwinkel 0° verstärkt die Schneidkante und erhöht die Bruchfestigkeit, was bei der Zerspanung zäher Werkstoffe zu höherer Prozesssicherheit führt. Wie unterstützt der L65T-Spanbrecher die Bearbeitung? Der L65T-Spanbrecher sorgt für gezielte Spanformung und verhindert Aufbauschneiden, wodurch die Standzeit verlängert und die Oberflächenqualität stabilisiert wird. Welche Vorteile bietet die beschichtete Hartmetallsorte WSM45X? Die WSM45X-Sorte kombiniert Beschichtung und Hartmetallträger für bessere Wärmebeständigkeit, stabile Schneidkante und wirtschaftliche Standzeiten bei anspruchsvollen Materialien. Ist diese Wendeschneidplatte für Serienfertigung geeignet? Ja, die Konstruktion und Materialwahl der WSM45X-Wendeschneidplatte machen sie besonders geeignet für produktive Serienfertigung mit hoher Prozesssicherheit. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
XNHX130616R-L65T WSP45G Wendeplatten - Walter Tools
Efficient milling performance and extended tool life result from the combination of Tiger·tec Gold coating and the robust WSP45G grade; optimised chip control and a negative 0° rake contribute to consistent surface quality when machining Stahl, rostfreier Stahl and heat-resistant superalloys. Order the insert directly via Metav Werkzeuge or contact consultants for application-specific advice. XNHX130616R-L65T WSP45G milling insert — Tiger·tec Gold, 0° negative rake — Walter Tools The XNHX130616R-L65G WSP45G is a coated milling insert designed for versatile milling applications, especially where stable cutting edges and reliable chip control are required Tiger·tec Gold PVD coating for long tool life Versatile for Stahl, rostfreier Stahl and superalloys Negative 0° rake for secure chip control 1.6 mm corner radius for robust edges Durable coating and wear resistance for longer tool life The insert combines the Tiger·tec Gold coating with the WSP45G grade, creating a PVD-coated carbide substrate that balances toughness and wear resistance. This combination is engineered for milling cycles that generate thermal and mechanical loads typical of machining Stahl and rostfreier Stahl, while also tolerating demanding work on superalloys. The result is a stable cutting edge that reduces flank wear and the frequency of tool changes, supporting continuous production and predictable tool-life planning. Secure chip control and consistent surface quality Equipped with the L65T chipbreaker and a 0° rake, the insert promotes controlled chip formation and evacuation during peripheral and face milling. Controlled chip flow reduces the risk of edge build-up and supports a consistent surface finish, which lowers the need for secondary operations. The geometric choices—corner radius and chipbreaker design—are tailored to deliver process security under varying cutting parameters, improving repeatability across batches and minimising scrap rates. Practical benefits: fewer tool changes and broad material coverage With a 1.6 mm corner radius and a compact 13 mm plate profile, the insert offers a good compromise between edge strength and small-cutter capability; the designation thickness 06 indicates the plate's robust build for repeated indexing. The versatility across P/M/S material groups reduces tool inventory requirements and simplifies toolholder selection for mixed-production environments. For detailed cutter compatibility and parameter tuning, Metav Werkzeuge provides application support to match cutter bodies and indexable layouts. Contact Metav Werkzeuge to discuss how this Walter Tools Tiger·tec Gold milling insert suits specific machining tasks and to receive tailored recommendations for cutter and parameter selection Technical Data Article number: XNHX130616R-L65T-WSP45G-WALTER Designation: XNHX130616R-L65T WSP45G Product type: Milling insert (indexable) Series: Tiger·tec Gold Grade: WSP45G Manufacturer: Walter Tools Dimensions & measurable data Plate size: 13 mm Corner radius: 1.6 mm Thickness: 06 Rake angle: 0° (negative) Tolerance class: H Coating & features Coating: Tiger·tec Gold (PVD-coated carbide) Chipbreaker: L65T Material suitability: P / M / S (Stahl, rostfreier Stahl, superalloys) Execution: X ISO designation: XNHX130616R-L65T WSP45G FAQ Which materials is this insert suitable for? The XNHX130616R-L65T WSP45G milling insert (Walter Tools, SKU XNHX130616R-L65T-WSP45G-WALTER) is specified for P / M / S workpiece groups, which means Stahl, rostfreier Stahl and heat-resistant superalloys. What advantage does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the WSP45G grade improves wear resistance and edge stability under thermal load; this reduces tool changes and helps maintain consistent part quality. How does the L65T chipbreaker affect machining? The L65T chipbreaker promotes reliable chip formation and evacuation with the negative 0° rake, contributing to stable cutting and improved surface finishes during milling operations. Is the insert suitable for heavy roughing operations? With a 1.6 mm corner radius and the robust WSP45G grade, the insert is designed to withstand significant mechanical load; selection for heavy roughing should include cutter-body rigidity and correct parameter settings. How should the 0° rake be interpreted for programming cutting data? The 0° (negative) rake indicates a neutral to slightly negative cutting geometry that supports secure chip control and edge strength; adapt feed and speed to workpiece material and cutter stability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are used for explanation only and do not imply any affiliation between our company and the named manufacturers. The described item is an original, brand-new product of the manufacturer.
XNHX130620R-L65T WSM45X Wendeplatten - Walter Tools
Take advantage of the proven combination of a coated carbide grade (WSM45X) and a dedicated L65T chipbreaker for secure chip control and extended tool life in demanding materials; order the milling insert directly via Metav Werkzeuge or consult our technical advisers for application support. XNHX130620R-L65T WSM45X – Milling indexable insert, coated carbide, for stainless steels & superalloys – Walter Tools A XNHX130620R-L65X WSM45X milling insert designed for high-demand machining of stainless steels and heat-resistant superalloys, featuring a 0° negative rake for robust cutting performance Coated carbide grade WSM45X Integrated L65T chipbreaker 0° negative rake angle Optimised for stainless steels and superalloys Higher productivity on difficult-to-machine alloys The combination of WSM45X coating and the insert geometry delivers measurable gains when machining tough materials. The coated carbide grade is tuned for heat resistance and edge stability, which reduces the frequency of tool changes and supports consistent cycle times. For production environments where process reliability matters, this insert helps to maintain cutting conditions and to reduce scrap from built-up edge. The specification targets ISO groups M (stainless steels) and S (heat-resistant superalloys and titanium), so material-specific challenges such as poor thermal conductivity and high work-hardening are addressed by the substrate and coating system. Improved chip control and surface quality The dedicated L65T chipbreaker and the 0° negative rake work together to produce predictable chip formation and to shield the cutting edge from thermal and mechanical shock. A corner radius 2 increases edge strength for interrupted cuts while preserving surface finish, particularly on stainless grades prone to smearing. For users less familiar with insert geometries: a negative rake reduces axial thrust and promotes a calmer cutting action in heavy cuts, while the chipbreaker geometry shapes the chip to avoid entanglement and to facilitate evacuation from the cut. Consistent tool life and integration into production The insert’s designation and build—XNHX130620R-L65T—allow simple identification and repeatability across toolholders and setups. Tolerance class H and plate thickness 06 contribute to stable clamping and predictable runout, supporting repeatable part quality. Where process security and cost-efficiency are priorities, the design minimises downtime for regrinding or replacement. The insert is a practical choice for batch and continuous manufacturing where long, consistent tool life and reduced process variation lead directly to lower unit costs. For process-critical machining of stainless steels and heat-resistant superalloys, request the Walter Tools XNHX130620R-L65T WSM45X from Metav Werkzeuge or contact our specialists for tailored application advice – Metav Werkzeuge is available to assist. Technical Data SKU: XNHX130620R-L65T-WSM45X-WALTER Product type: Milling indexable insert Name / designation: XNHX130620R-L65T WSM45X Manufacturer: Walter Tools Facts Plate size: 13 Plate thickness: 06 Corner radius: 2 Rake angle: 0° (negative) Tolerance class: H Special features Grade: WSM45X (coated carbide) Chipbreaker: L65T Application groups: M (stainless steels), S (superalloys, titanium) Series: Walter carbide grade – open series Execution: X FAQ What materials is this insert suited for? The XNHX130620R-L65T WSM45X insert is formulated for stainless steels (ISO M) and heat-resistant superalloys/titanium (ISO S), where its coated carbide grade supports stable edge life. How does the L65T chipbreaker affect machining? The L65T chipbreaker shapes and controls chips for reliable evacuation, improving surface finish and reducing the risk of chip re-cutting when using the XNHX130620R-L65T insert. Is the 0° negative rake beneficial for interrupted cuts? Yes. The 0° negative rake provides a robust cutting edge that tolerates shock and helps maintain edge integrity during interrupted or heavy cuts with this type of insert. What does tolerance class H mean for production? Tolerance class H indicates tighter geometric tolerances on the insert, which supports consistent seating in the toolholder and reproducible part quality when using the XNHX130620R-L65T. Can this insert be used on titanium components? Depending on the specific titanium alloy and machining parameters, the WSM45X grade is intended to handle titanium and heat-resistant superalloys; machining parameters should be verified for the exact alloy and operation. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered item is an original, factory-new product of the manufacturer Walter Tools.
XNHX130624R-L65T WSM45X L65T Wendeplatten - Walter Tools
Take advantage of a coated carbide grade optimised for hard-to-machine alloys, the L65T chipbreaker for reliable chip control and a 0° negative rake that supports heavy milling cuts for steady production throughput; order the insert directly via Metav Werkzeuge or ask for process advice from their specialists. XNHX130624R-L65T WSM45X Fräswendeschneidplatte — 0° negative rake, 2.4 mm corner radius | Walter Tools The XNHX130624R-L65X WSM45X is a coated carbide milling insert designed for heavy-duty roughing of rostfreier Stahl and heat-resistant superalloys, offering stable chip formation and extended edge life in demanding applications Coated carbide grade WSM45X for tough alloys Optimised L65T chipbreaker for stable chips 0° negative rake for heavy-duty milling 2.4 mm corner radius for extended edge life Increased throughput through stable cutting performance The coated carbide WSM45X grade delivers a consistent mix of wear resistance and thermal stability, which translates into predictable tool life and fewer interruptions in the production cycle. Intended for rostfreier Stahl and high-temperature alloys, this insert supports secure chip formation even under elevated cutting forces. The net effect is measurable: fewer tool changes and a smoother production flow, helping to cut overall machining costs while maintaining cycle-time targets. Technical descriptions such as “coated carbide” denote a multi-layer wear coating applied to a hardmetal substrate to improve oxidation resistance and edge retention during tough cutting conditions. Better surface quality and fewer reworks through geometry choices A 0° negative rake geometry provides a robust cutting edge that resists chipping during heavy engagement, while the 2.4 mm corner radius spreads cutting loads to reduce localised wear. Combined with the L65T chipbreaker, these features promote short, controllable chips and help reduce built-up edge formation on rostfreier Stahl, which is prone to smearing and work hardening. In practice this means improved dimensional stability and reduced secondary finishing operations for components where surface integrity matters. The negative rake is particularly useful when encountering variations in workpiece hardness or interrupted cuts where edge strength is paramount. Ease of selection and secure integration into machining lines The insert’s series designation and open availability make integration into existing toolholders straightforward. With a tolerance class H, plate size 13 and thickness 06, the geometry suits conventional milling setups where repeatability is required. The L65T chipbreaker is tuned for reliable chip evacuation across the WSM45X range, while the coated carbide substrate copes with the thermal loads typical of rostfreier Stahl and superalloys. For precise cutting parameters and to align the insert with machine capability, consult Metav Werkzeuge’s technical advisors; they can recommend feed and speed windows and compatible holders to ensure the best combination of productivity and tool life. Discuss machining requirements with Metav Werkzeuge to specify Walter Tools WSM45X inserts for rostfreier Stahl and superalloys — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored recommendations Technical data SKU: XNHX130624R-L65T-WSM45X-WALTER Designation: XNHX130624R-L65T Full designation: XNHX130624R-L65T WSM45X Manufacturer: Walter Tools Product type: Fräswendeschneidplatte Core dimensions Corner radius: 2.4 mm Plate size: 13 Thickness: 06 Free angle: 0° (negative) Tolerance class: H Special features Grade: WSM45X (coated carbide) Series: Walter Schneidstoffsorte - Serie offen Chipbreaker: L65T Execution: X Material suitability: S / M; suitable for rostfreier Stahl and heat-resistant superalloys FAQ What materials is this insert best suited for? The XNHX130624R-L65T WSM45X insert is optimised for rostfreier Stahl and heat-resistant superalloys (S / M), offering thermal stability and controlled chip formation for these challenging groups. How does the L65T chipbreaker affect machining? The L65T chipbreaker on this Walter Tools insert promotes short, controlled chips and improved evacuation, reducing the risk of entanglement and supporting consistent surface quality during heavy cuts. When should a 0° negative rake be chosen over positive rake geometries? A 0° negative rake is recommended for roughing and applications with interrupted cuts or hard spots because it provides a tougher cutting edge and greater resistance to edge chipping compared with positive rake geometries. Is the insert interchangeable with common 13 mm indexable systems? The insert’s plate size 13 and tolerance class H mean it fits standard toolholders designed for this form; however, verification of holder compatibility is advised before assembly. What are the main advantages of the WSM45X grade? WSM45X is a coated hardmetal grade engineered for high-temperature resistance and stable edge life on rostfreier Stahl and superalloys, delivering a balance of wear resistance and toughness for productive machining. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany — The Walter AG (brand presentation: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation purposes only and do not imply any affiliation between Metav Werkzeuge and the trademark owners. The item offered is an original, factory-new product of the manufacturer.
XNHX130630R-L65T WSM45X WSM45X Wendeplatten - Walter Tools
Combine the WSM45X cutting-grade performance with the robust L65T chipbreaker and the negative 0° relief to secure stable cutting and consistent tool life in demanding stainless and heat-resistant alloy applications. Order the insert via Metav Werkzeuge or consult their technical team for process matching. XNHX130630R-L65T WSM45X milling insert — negative 0° relief, corner radius R3 (Walter Tools) The XNHX130630R-L65X WSM45X is a coated carbide milling insert intended for heavy-duty machining of stainless steels and heat-resistant superalloys, offering a sturdy edge geometry and optimised chip formation for difficult-to-cut materials. Coated carbide grade WSM45X Optimised for stainless steel and superalloys Negative 0° relief for secure cutting Corner radius R3 for robust tool life Stable edge performance for demanding materials The coated carbide grade WSM45X is designed to provide heat resistance and stable cutting edges when machining materials that tend to work-harden or produce built-up edge, such as stainless steels and superalloys. The insert’s chipbreaker L65T promotes controlled chip formation, reducing chatter and helping to maintain surface finish. By combining a tough substrate with an engineered coating, the indexable insert supports longer tool life and fewer interruptions, which leads to more predictable cycle times and a lower cost per part. Secure cutting geometry that improves process reliability With a negative 0° relief and a corner radius R3, the geometry prioritises strength at the cutting edge and resistance to mechanical shock. The negative relief increases the support behind the cutting edge, making the insert suitable for heavier depths of cut and interrupted cuts often encountered in industrial milling. This geometry reduces the risk of edge chipping and supports stable cutting forces, which contributes directly to process reliability and consistent component quality over production runs. Clear application focus and machining advantages The insert is specified for the ISO groups S and M, indicating suitability for heat-resistant superalloys, titanium, and stainless steels. These materials demand coatings and substrate properties that limit thermal damage and avoid premature flank wear; the WSM45X grade addresses these needs. Using this insert can result in improved surface integrity and fewer rework cycles, which benefits throughput and downstream assembly quality. For users transitioning from general-purpose grades, this specialised option offers a measurable step up in performance where conventional inserts struggle. Contact Metav Werkzeuge to discuss how the Walter Tools XNHX130630R-L65T WSM45X insert can be integrated into current milling operations or to request machining parameter recommendations from their specialists. Technical data Article number: XNHX130630R-L65T-WSM45X-WALTER Label: Fräswendeschneidplatte XNHX130630R-L65T WSM45X Walter Tools SKU: XNHX130630R-L65T-WSM45X-WALTER Manufacturer: Walter Tools Facts Free angle: 0° (negative) Corner radius: R3 Plate size: 13 Thickness: 06 Tolerance class: H Special features Grade: WSM45X (coated carbide) Chipbreaker: L65T Execution: X Series: Walter cutting-grade series – open Material suitability: S / M (stainless steels; heat-resistant superalloys) ISO designation: XNHX130630R-L65T WSM45X FAQ What materials is this insert designed for? The insert is formulated for machining stainless steels and heat-resistant superalloys (ISO groups M and S) thanks to the WSM45X coated carbide grade and the L65T chipbreaker. How does the negative 0° relief affect performance? A negative 0° relief increases support behind the cutting edge, improving resistance to chipping and enabling stable cuts under heavier loads when using the Walter Tools insert. What machining benefits does the corner radius R3 provide? The R3 corner radius strengthens the cutting edge and helps distribute cutting forces, resulting in improved edge life and resistance to mechanical shock during interrupted cuts. Is the chip control suitable for long continuous cuts? The L65T chipbreaker is engineered to produce predictable chip forms in tough alloys, aiding coolant flow and reducing the likelihood of chip entanglement in long milling passes. Can this insert be used for finishing operations? While optimised for robust cutting and stability, the grade and edge preparation can deliver acceptable surface quality; parameter adjustment towards lower feed and depth of cut will improve finishing results. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used here for descriptive purposes only and do not imply any affiliation or endorsement. The offered item is an original, factory-new product from the stated manufacturer.
XNHX130632R-L65T WSM45X Wendeplatten - Walter Tools
Take advantage of the combination of WSM45X coated carbide performance, the L65T chipbreaker and a 0° negative rake for reliable cutting in stainless steel and superalloys; order the insert directly via Metav Werkzeuge or consult our specialists for application support. XNHX130632R-L65T WSM45X Fräswendeschneidplatte – Coated carbide for stainless steel and superalloys | Walter Tools A XNHX130632R-L65X WSM45X indexable milling insert engineered for stable material removal in stainless steel and heat-resistant superalloys, offering a robust corner radius and optimised chip control Coated carbide grade WSM45X Optimised chip control L65T 0° negative rake for cutting stability 3.2 mm corner radius for increased robustness Greater process reliability when machining difficult materials The insert’s WSM45X designation denotes a coated carbide grade developed for demanding applications in stainless steel (ISO group M) and heat-resistant superalloys or titanium alloys (ISO group S). Coatings on modern grades reduce adhesion and thermal load at the cutting edge; this yields more consistent tool life and fewer interruptions in the production cycle. The combination of a thermally resistant grade with an optimised geometry reduces the risk of built-up edge and improves dimensional repeatability on components where tight tolerances are critical. This paragraph focuses on measurable improvements in process stability and explains why the coating and substrate matter for shops machining tough-to-cut alloys. Controlled chip formation and edge security for quieter production The dedicated L65T chipbreaker is designed to shape and evacuate chips reliably under challenging cutting conditions. Controlled chip formation reduces the likelihood of entanglement, protects the workpiece surface and lowers secondary operations for chip management. Coupled with a 0° negative rake, the insert shifts cutting forces to a more secure edge engagement that favours edge stability over aggressive shearing—particularly beneficial when each pass must preserve surface integrity. The result is a predictable machining step that supports higher machine utilisation and reduces unplanned stoppages. Robust geometry for repeatable performance and longer intervals between changes A 3.2 mm corner radius increases the edge strength at the nose of the insert, reducing chipping under interrupted cuts and cyclic loads. This robustness is especially relevant for operations with variable engagement or where fixtures introduce runout; a larger radius spreads stress and helps maintain nominal dimensions longer. The insert thickness and plate size are matched to common holders for milling operations, providing simple integration into existing tool systems and enabling shops to standardise on a high-performance grade for a wider material spectrum. Practical benefits for production planning and tool management Adopting this insert supports a rational, cost-conscious strategy: fewer tool changes, lower scrap risk and more predictable machining windows. The grade’s suitability for both stainless steel and superalloys allows consolidation of tool inventories, simplifying logistics and reducing downtime for tool swaps. For process engineers, data-backed cutting recommendations combined with the insert’s geometry help to define stable feeds and speeds that balance productivity and tool life. This emphasis on measurable gains helps production planners make informed decisions that improve overall equipment effectiveness. For machining stainless steel and superalloys with Walter Tools' WSM45X grade, contact Metav Werkzeuge for tailored cutting data and prompt delivery: info@metav-werkzeuge.com · +49 2822 7131930 Technical data Article number: XNHX130632R-L65T-WSM45X-WALTER Label: Fräswendeschneidplatte XNHX130632R-L65T WSM45X Walter Tools Product type: Fräswendeschneidplatte Manufacturer: Walter Tools Grade: WSM45X Series: Walter Schneidstoffsorte - Serie offen Facts Corner radius: 3,2 mm Plate size: 13 Plate thickness: 06 Rake angle: 0° (negativ) Tolerance class: H Special features Chipbreaker: L65T Coating/substrate: beschichtetes Hartmetall (coated carbide) Applicable material groups: S / M (superalloys/Titan and stainless steel) Designation without grade: XNHX130632R-L65T ISO designation: XNHX130632R-L65T WSM45X FAQ What materials is this insert intended for? The XNHX130632R-L65T WSM45X insert is formulated for stainless steel (ISO group M) and heat-resistant superalloys or titanium (ISO group S), providing thermal resistance and secure chip control for these materials. How does the L65T chipbreaker improve machining? The L65T chipbreaker shapes chips to promote safe evacuation and reduces the chance of entanglement, which helps maintain surface quality and reduces interruptions during milling operations with the WSM45X grade. Why is a 0° negative rake beneficial for this insert? A 0° negative rake increases edge stability and distributes cutting forces in a way that protects the cutting edge, making the insert well suited to interrupted cuts and hard-to-machine alloys where edge integrity is critical. Can this insert be used in standard milling holders? The insert’s designation and dimensions correspond to common holder systems; compatibility should be checked against the toolholder specification, but the geometry is intended for straightforward integration into existing milling setups. Manufacturer / Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
XNHX130632R-L65T WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of robust edge stability, versatile material coverage and an optimised chipbreaker for uninterrupted production. Secure the insert via Metav Werkzeuge for reliable supply or consult the specialists for application advice. XNHX130632R-L65T WSP45G milling insert — Walter Tools, Tiger·tec Gold, 3.2 mm corner radius The XNHX130632R-L65G is a precision milling insert designed for versatile face and shoulder milling tasks across steels, rostfreier Stahl and heat‑resistant alloys; suitable for productive, stable finishing and roughing operations Tiger·tec Gold PVD coating Versatile for Steel, rostfreier Stahl and Superalloys 0° negative rake for robust cutting 3.2 mm corner radius for stable edge Maximum productivity across mixed materials The Tiger·tec Gold technology combined with the WSP45G grade delivers a wear‑resistant, PVD‑coated carbide designed for long tool life and consistent performance. This combination supports machining of unalloyed and alloyed steels, rostfreier Stahl and high‑temperature superalloys by improving thermal resistance and reducing flank wear. The result is fewer tool changes and a more continuous production flow, which directly benefits cycle time and process reliability. Emphasis is on repeatable results rather than one‑off performance. Stable cutting behaviour and consistent chip control The insert’s chipbreaker L65T and 0° negative rake work together to produce predictable chip formation and minimise edge build‑up when cutting tougher materials. A 3.2 mm corner radius increases edge strength, making the insert particularly suitable for interrupted cuts and moderate radial engagement. The combination of geometry and chip control reduces vibration and optimises surface finish, translating technical features into measurable shop‑floor advantages: lower scrap rates and improved part quality. Economical machining and reduced tooling complexity With applicability across P/M/S material groups, the grade eliminates the need for multiple dedicated grades in many mixed‑material production runs. The durable coating and stable cutting edge contribute to longer life‑cycles, which lowers tooling consumption and setup frequency. This insert therefore supports cost‑efficient production, especially where batch sizes and material variety demand flexible, high‑performance tooling rather than frequent retooling. Practical fitment and tolerance guidance for integration The insert is supplied in the format XNHX130632R‑L65T with a plate size designation of 13 and thickness code 06, tolerance class H, and a precision finish suited to modern milling holders. The nominal geometry supports standard clamping systems and is engineered for compatibility with common cutter bodies used in face and peripheral milling. For exact holder matching and cutting parameters, refer to machine capability and cutting data recommendations to ensure optimised performance. Contact Metav Werkzeuge today for application‑specific recommendations and to arrange supply of the Tiger·tec Gold XNHX130632R‑L65T WSP45G insert for high‑productivity milling Technical data SKU: XNHX130632R-L65T-WSP45G-WALTER Article label: Fräswendeschneidplatte XNHX130632R-L65T WSP45G Walter Tools Brand: Walter Tools Series: Tiger-tec Gold Grade: WSP45G Designation: XNHX130632R-L65T WSP45G Facts Corner radius: 3,2 mm Plate size: 13 Rake: 0° (negative) Thickness code: 06 Tolerance class: H Special features Coating: Tiger·tec Gold (PVD) Material: P / M / S Chipbreaker: L65T Application: milling inserts for steels, rostfreier Stahl and superalloys Execution: X Series description: tough, versatile PVD grade for milling FAQ What materials can this insert machine reliably? The XNHX130632R‑L65T WSP45G insert from Walter Tools is specified for machining steels (P), rostfreier Stahl (M) and heat‑resistant superalloys and titanium (S). How does the chipbreaker L65T influence machining? The L65T chipbreaker promotes controlled chip formation and stable evacuation, which helps maintain edge integrity and improves surface finish during both finishing and heavier cuts. Is the 0° negative rake suitable for interrupted cuts? Yes, the 0° negative rake and 3.2 mm corner radius increase edge strength and resistance to chipping, making the insert suitable for interrupted or mixed engagement milling. What do the size and thickness codes mean for tool selection? The designation indicates a plate size of 13 and thickness code 06; these must match the cutter body geometry to ensure secure clamping and correct cutting projection. Can this insert be used for high‑temperature alloys like Inconel? The WSP45G grade is engineered for heat resistance and stable cutting in S‑group materials, making it appropriate for many high‑temperature alloys when combined with suitable cutting parameters. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
XNHX130640R-L65T WSM45X WSM45X Wendeplatten - Walter Tools
Take advantage of the combination of WSM45X coated carbide, a negative 0° rake for secure cutting, and the robust 4 mm corner radius to maintain process reliability in demanding machining of stainless steels and heat‑resistant superalloys; order directly via Metav Werkzeuge or consult our specialists for application support. XNHX130640R-L65T WSM45X milling insert — Coated carbide for stainless steels and superalloys | Walter Tools A XNHX130640R-L65T WSM45X indexable milling insert engineered for heavy‑duty machining of stainless steel and high‑temperature alloys, combining a stable geometry with a specialised chipbreaker for consistent chip control. Coated carbide grade WSM45X Suitable for stainless steels and superalloys Negative 0° rake for cutting stability 4 mm corner radius for durable edges High‑performance grade for difficult‑to‑cut materials The core advantage of the insert lies in the WSM45X coated carbide grade, developed for secure chip formation and enhanced edge life when tackling stainless steels and heat‑resistant superalloys. The coating and substrate combination promotes thermal resistance and wear protection, which reduces the frequency of tool changes and supports a smoother production flow. For machining environments where heat generation and material toughness are typical constraints, this grade sustains cutting edge integrity and reduces the risk of built‑up edge, translating into higher net productivity and fewer interruptions. Geometry engineered for stability and reproducible results The insert’s negative 0° rake and 4 mm radius create a geometry that favours cutting stability and mechanical strength at the cutting zone. A negative rake increases edge robustness under heavy loads and helps to dampen chatter, while the larger corner radius spreads cutting forces to extend effective tool life. The included L65T chipbreaker is tailored for secure chip control in demanding materials, improving evacuation and reducing rework. These design elements ensure reliable results across repeated cycles and are particularly useful in operations that prioritise consistent surface quality and tolerance control. Practical benefits for workshop efficiency With the format and dimensions optimised for rigid setups—notably the 13 mm plate size and specified thickness—the insert supports predictable clamping and replacement routines. The combination of grade, chipbreaker and geometry means less time spent on re‑grinding or unexpected tool exchanges, reducing downtime and contributing to a better cost‑benefit ratio in medium to high volume production. For departments seeking an insert that balances process reliability with broad material coverage, this option reduces setup variability and supports a leaner tooling inventory. For tailored tooling advice and immediate availability of Walter Tools inserts, contact Metav Werkzeuge for technical consultation and ordering at info@metav-werkzeuge.com or call +49 2822 7131930 Technical specifications Article number / SKU: XNHX130640R-L65T-WSM45X-WALTER Label: Fräswendeschneidplatte XNHX130640R-L65T WSM45X Walter Tools Product type: milling insert Grade: WSM45X Series: Walter Schneidstoffsorte - Serie offen Numeric data Corner radius: 4 Plate size: 13 Thickness: 06 Rake angle: 0° (negative) Tolerance class: H Chipbreaker: L65T Design and special features Coated carbide (WSM45X) Suitable materials: stainless steels (M), heat‑resistant superalloys and titanium (S) Execution: X Insert designation: XNHX130640R-L65T Optimised for secure chip formation and stable cutting edges FAQ Which materials are suitable for this insert? The XNHX130640R-L65T WSM45X milling insert is designed for stainless steel (stainless steels) and heat‑resistant superalloys; the WSM45X grade supports thermal resistance and improved chip control for these groups. What advantages does a negative 0° rake provide? A negative 0° rake increases cutting edge robustness and reduces the likelihood of chipping under heavy loads, improving stability during interrupted or heavy cuts and extending edge life on the insert. When is the 4 mm corner radius recommended? A 4 mm radius is beneficial for operations requiring increased cutting edge strength and reduced stress concentration, typically used in roughing or semi‑finishing where edge durability is prioritised. What role does the L65T chipbreaker play? The L65T chipbreaker is configured to support secure chip formation and evacuation in tough materials, lowering the risk of rework and helping to maintain consistent surface finish quality. Is this insert suited for finishing passes? Depending on the selected cutter geometry and parameters, the insert can be used for semi‑finishing; however, for fine finishing tasks, a dedicated geometry with a smaller corner radius may be preferable. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and brand names are the property of their respective owners. Brand names and protected product designations are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, factory‑new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com