CNMG160612-RP7 WPP30G WPP30G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, a robust RP7 chipbreaker and a stable rhombic geometry for reliable steel turning with low tool-wear; order the insert directly via Metav Werkzeuge or contact our consultants for application advice. CNMG160612-RP7 WPP30G indexable turning insert — Tiger‑tec Gold, for steel (rhombic 80°, 0° negative) (Walter Tools) The CNMG160612-RP7 WPP30G is a rhombic 80° indexable turning insert designed for productive steel machining with a Tiger‑tec Gold coated carbide grade. Tiger‑tec Gold coated, robust performance Optimised RP7 chipbreaker for steel Rhombic 80° geometry with 1.2 mm nose Negative 0° rake for stable cutting Enhanced reliability and wear resistance for steel turning The combination of the Tiger‑tec Gold coating and the WPP30G grade delivers markedly improved wear resistance and predictable edge life when machining ISO P materials (steel). The coating technology was developed to reduce flank wear and sustain cutting performance under the thermal and mechanical loads typical of steel turning. This means longer tool life and fewer insert changes, which supports uninterrupted production and lower unit costs per component. Predictable chip control and consistent surface quality Built around the RP7 chipbreaker, the insert promotes controlled chip formation for a wide range of steels, minimising built-up edge and erratic chip behaviour. The rhombic 80° geometry together with the 1.2 mm nose radius and the 0° negative rake stabilises cutting forces, resulting in a steady feed response and improved surface finish. For workshops seeking reproducible processes, the insert’s chip control helps maintain cycle times and reduces downstream deburring. Easy integration into turning operations and process economy The CNMG form and standard dimensions ensure straightforward mounting in common toolholders, simplifying tool setup and inventory management. The coated carbide substrate and consistent grade characteristics provide process security across varying cutting conditions, cutting speeds and depths of cut. Reduced downtime through fewer index changes and high repeatability contribute directly to enhanced productivity and an attractive cost-to-performance ratio for series production. Contact Metav Werkzeuge for tailored cutting data and to secure the CNMG160612-RP7 WPP30G Tiger‑tec Gold insert from Walter Tools for robust steel turning applications Technical Data Article number: CNMG160612-RP7-WPP30G-WALTER Designation: CNMG160612-RP7 WPP30G Series: Tiger‑tec Gold Grade: WPP30G Facts Size: 16 Thickness: 06 Nose radius: 1.2 mm Clearance angle: 0° (negative) Geometry: Rhombic 80° Tolerance class: M Special features Coating technology: Tiger‑tec Gold Substrate: coated carbide Chipbreaker: RP7 Application group: Steel (ISO P) Execution: G Brand: Walter Tools FAQ What materials is this insert suitable for? The CNMG160612-RP7 WPP30G is optimised for machining steels (ISO P); the WPP30G grade and Tiger‑tec Gold coating are tuned for common unalloyed and alloyed steel applications. How does the RP7 chipbreaker affect performance? The RP7 chipbreaker improves chip control during turning, reducing built-up edge and promoting stable chip flow, which contributes to more consistent surface finish and longer tool life with this insert. Is the insert compatible with standard CNMG toolholders? Yes, the rhombic CNMG form conforms to standard toolholder interfaces, enabling straightforward integration into existing turning setups. What advantage does the 0° negative rake offer? A 0° negative rake increases cutting-edge strength and stability under interrupted cuts or heavy roughing passes, helping to avoid premature edge chipping when machining steels. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is an original, brand-new product from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany
CNMG160616-MK5 WKK10S Wendeplatten - Walter Tools
Benefit from high wear resistance and optimised chip control thanks to the Tiger·tec Silver grade and the MK5 chipbreaker; the combination ensures longer tool life and stable cutting in cast-iron turning. Order the insert directly via Metav Werkzeuge or contact our consultants for process advice. CNMG160616-MK5 WKK10S Drehwendeschneidplatte – Tiger·tec Silver for cast iron | Walter Tools The CNMG160616-MK5 WKK10S is a rhombic 80° turning insert designed for efficient machining of cast iron, combining a coated carbide grade with a dedicated chipbreaker for consistent performance. Tiger·tec Silver coating for wear resistance Designed for cast iron (K) materials Rhombic 80° geometry, 1.6 mm corner radius Negative rake 0° for stable cutting Consistent wear resistance for productive cast-iron turning The WKK10S grade, applied within Walter Tools' Tiger·tec Silver series, is a coated carbide solution formulated for abrasive cast-iron applications. Because the grade is tuned to the short, brittle chips typical of cast materials, the insert provides improved wear resistance and extended edge life compared with uncoated alternatives. The result is fewer tool changes and higher machine uptime, which directly supports process efficiency and predictable production cycles. Geometry tuned for strength and reliable surface quality The CNMG rhombic shape with 80° lead angle and a 1.6 mm corner radius balances cutting-edge strength and achievable surface finish. The negative 0° rake increases edge robustness under interrupted cuts and heavy engagement, while the MK5 chipbreaker promotes controlled chip formation. This geometry and edge preparation allow stable cutting forces and reduced vibration, enhancing dimensional repeatability and component quality even in challenging cast-iron workpieces. Practical application advice for stable machining results As an indexable insert for turning, the plate is intended for a range of turning tasks on cast iron according to ISO group K. The MK5 chipbreaker supports reliable chip control during both roughing and finishing passes, lowering the risk of built-up edge and workpiece damage. For best results in production environments, pair the insert with a rigid tool holder and a stable clamping setup to exploit the grade’s process security and achieve consistent cycle times. For availability, technical matching or to discuss process optimisation with Walter Tools' Tiger·tec Silver inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for personalised advice and stock information. Technical data Article number: CNMG160616-MK5-WKK10S-WALTER Designation: CNMG160616-MK5 WKK10S Manufacturer: Walter Tools Series: Tiger-tec Silver Facts Size: 16 mm Thickness code: 06 Corner radius: 1.6 mm Free angle: 0° (negative) Tolerance class: M Special features Coating/grade: WKK10S (coated carbide, Tiger·tec Silver) Chipbreaker: MK5 Geometry: rhombic 80° Application: cast iron (ISO group K) Execution: G FAQ What materials is this insert suitable for? The CNMG160616-MK5 WKK10S from Walter Tools is designed primarily for cast iron machining (ISO group K) and is optimised for the abrasive, short-chipping behaviour typical of these materials. What does the MK5 chipbreaker do? The MK5 chipbreaker on this insert controls chip formation in cast-iron turning, producing short, manageable chips and reducing the risk of chip entanglement and built-up edge. How does the 1.6 mm corner radius affect performance? A 1.6 mm corner radius offers a compromise between edge strength and surface finish; it increases resistance to edge wear and is suitable for stable cutting conditions where a secure edge is required. Is the Tiger·tec Silver grade a coating or substrate? Tiger·tec Silver refers to the coating technology applied to the WKK10S coated carbide grade, delivering improved wear resistance and longer tool life in abrasive cast-iron applications. Can this insert be used for finishing as well as roughing? Yes, the insert’s geometry and MK5 chip control make it suitable for both roughing and certain finishing passes on cast iron when used with appropriate cutting parameters and a rigid setup. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Brand names and registered trademarks are mentioned solely for explanatory purposes; there is no affiliation between our company and the named brands. The offered item is an original, factory-new product of Walter Tools.
CNMG160616-MK5 WKK20S Wendeplatten - Walter Tools
Take advantage of a high‑productivity solution for cast iron: the coated WKK20S grade delivers stable chip formation and extended tool life while the rhombic 80° geometry with a 1.6 mm corner radius ensures consistent dimensional control. Order the CNMG160616‑MK5 WKK20S directly via Metav Werkzeuge or consult the technical team for application support. CNMG160616-MK5 WKK20S — Turning insert for cast iron, Walter Tools CNMG160616‑MK5 WKK20S is a rhombic 80° turning insert engineered for productive machining of cast iron in heavy and interrupted cuts Tiger‑tec Silver coated cemented carbide Optimised for cast iron machining Rhombic 80° form, 1.6 mm corner radius Negative 0° rake, MK5 chipbreaker High productivity through geometry and form The rhombic 80° form and the 1.6 mm corner radius provide a robust cutting edge that tolerates interrupted cuts and varying engagement angles. The combination of the CNMG format and a negative 0° rake angle yields a stable cutting direction and reduced tendency for edge chipping, which is particularly advantageous when turning abrasive cast iron. This geometry translates into fewer tool changes and consistent workpiece tolerances, supporting continuous, high‑throughput production. Coating and grade designed for abrasive materials The Tiger‑tec Silver coating applied to the WKK20S grade is optimised for wear resistance against abrasive cast iron surfaces. The coated cemented carbide substrate resists flank and crater wear while maintaining edge integrity under elevated temperatures. For operations where short, brittle chips and high abrasion are common, this grade extends tool life and reduces unplanned downtime, improving overall machining economy. Chip control and surface quality under real conditions The MK5 chipbreaker is shaped to manage the typically short, breaking chips of cast iron, ensuring controlled evacuation and minimised recutting. Controlled chip formation reduces surface damage and promotes a more repeatable finish on the component. Together with the insert’s tolerance class M and stable edge preparation, the geometry and chip control contribute to reliable part quality and reduced secondary operations. Application focus and practical advantages Specifically matched to cast iron (ISO group K), this insert supports a broad range of turning tasks from roughing to finishing when parameters are set according to material and machine capability. The robust design allows for higher depths of cut and keeps mechanical stress on the cutting edge low, which helps to maintain productivity in mixed batch or single‑piece production environments. Tooling planners benefit from predictable tool life and lower stocking complexity. Contact Metav Werkzeuge for tailored cutting parameters, sample testing and fast delivery of Walter Tools inserts — telephone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: CNMG160616‑MK5‑WKK20S‑WALTER Designation: CNMG160616‑MK5 WKK20S Series: Tiger‑tec Silver Grade: WKK20S Manufacturer: Walter Tools Facts Shape: Rhombic 80° Size: 16 mm Thickness: 6 mm Corner radius: 1.6 mm Free rake: 0° (negative) Chipbreaker: MK5 Tolerance class: M Special features Coating: Tiger‑tec Silver Substrate: coated cemented carbide Material application: cast iron (ISO group K) Series suitability: productive turning, stable chip formation FAQ Which materials is this insert intended for? The CNMG160616‑MK5 WKK20S is designed primarily for machining cast iron (ISO group K) and is optimised for abrasive, short‑chip conditions. How does the Tiger‑tec Silver coating benefit production? The Tiger‑tec Silver coating improves wear resistance and thermal stability, resulting in longer tool life and more consistent surface finish in cast iron turning. What advantages does the MK5 chipbreaker offer? The MK5 chipbreaker ensures controlled chip formation for short, brittle chips typical of cast iron, promoting safe evacuation and minimising recutting. Is this insert suitable for interrupted cuts? Yes; the rhombic 80° geometry and negative rake provide a robust cutting edge that tolerates interrupted cuts and shock loads. Can the insert be used on automatic lathes and CNC turning centres? The insert’s format and tolerance class make it suitable for both CNC turning centres and automatic lathes when clamped in compatible toolholders. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160616-MM5 WMP20G WMP20G Wendeplatten - Walter Tools
Robust performance and predictable tool life result from the combination of the Tiger·tec Gold coating and the MM5 chipbreaker, delivering efficient turning of rostfreier Stahl under medium to robust conditions; order the CNMG160616-MM5 WMP20G directly via Metav Werkzeuge or consult the Metav team for application-specific advice. CNMG160616-MM5 WMP20G Drehwendeschneidplatte – Tiger·tec Gold, for rostfreier Stahl (Walter Tools) CNMG160616-MM5 WMP20G is a negative-rake rhombic insert designed for stable turning of rostfreier Stahl in medium to robust machining tasks Tiger·tec Gold coating for stable edge life Optimised MM5 chipbreaker for chip control Rhombic 80° insert with 1.6 mm corner radius Suitable for rostfreier Stahl (ISO M) Higher productivity through coated-carbide technology and reliable chip control The combination of the Tiger·tec Gold coating and the WMP20G grade creates a consistent cutting edge that reduces unexpected wear and supports longer tool cycles. Coated carbide technology offers thermal and abrasive resistance, which helps to avoid build-up on the cutting edge when machining rostfreier Stahl — a material group prone to toughness and heat generation. The integrated MM5 chipbreaker is optimised for secure chip formation, lowering the risk of stringing and interruptions. For production environments seeking measurable throughput gains, this insert aims to reduce changeover frequency and maintain part tolerances with predictable tool life. Geometry tuned for dimensional accuracy and surface quality The rhombic 80° shape with a 1.6 mm corner radius and a 0° (negative) free angle gives a balanced compromise between strength and finish capability. Negative rake geometry increases edge robustness under interrupted cuts and heavy engagement, while the moderate corner radius supports a consistent surface finish without sacrificing resistance to edge chipping. The CNMG format provides versatile seating in standard toolholders, enabling stable clamping and repeatable positioning. These geometric choices translate into reduced vibration, improved process stability and a lower rate of rework for turned components. Operational advantages and recommended applications Designed for ISO group M, this insert is targeted at machining rostfreier Stahl in applications with medium to robust cutting conditions where edge security and controlled chip flow are priorities. The coated carbide substrate resists thermal softening and abrasive wear, which supports consistent part quality across long runs. As part of Walter Tools’ Tiger·tec Gold family, the insert benefits from a modern coating stack that enhances process reliability and repeatability. Selection of this insert is particularly advantageous where a combination of productivity and reliable surface finish is required, such as in general engineering and component production for demanding corrosion-resistant alloys. Contact Metav Werkzeuge for tailored application advice and to reserve Tiger·tec Gold inserts for demanding rostfreier Stahl turning tasks Technical data Article number: CNMG160616-MM5-WMP20G-WALTER SKU: CNMG160616-MM5-WMP20G-WALTER Manufacturer: Walter Tools Product type: Drehwendeschneidplatte / indexable turning insert Series: Tiger·tec Gold Facts Insert size: 16 Corner radius: 1.6 mm Plate thickness: 06 Shape: Rhombus 80° Free angle: 0° (negative) Chipbreaker: MM5 Grade: WMP20G Tolerance class: M Special features Coating technology: Tiger·tec Gold Material class: coated carbide Application group: rostfreier Stahl (ISO M) Suitable for medium to robust machining conditions Negative-rake geometry for increased edge strength FAQ Which materials are recommended for this insert? The CNMG160616-MM5 WMP20G is specified for rostfreier Stahl (ISO M) and is optimised for the toughness and thermal behaviour typical of these alloys. What role does the MM5 chipbreaker play? The MM5 chipbreaker on the insert promotes controlled chip formation and reduces the chance of long, stringy chips when turning rostfreier Stahl, improving process reliability. How does the Tiger·tec Gold coating benefit production? Tiger·tec Gold on the WMP20G grade increases thermal and abrasive resistance of the cutting edge, which supports longer tool life and consistent part quality in serial production. What geometry should be expected when selecting a holder? The rhombic 80° shape with a 1.6 mm corner radius and a 0° negative rake requires holders compatible with CNMG inserts and negative-rake seating for secure clamping and repeatable positioning. Is this insert suitable for finishing and semi-finishing? Yes; the combination of the moderate corner radius and coated carbide construction makes the insert suitable for semi-finishing and finishing operations in conditions where a robust edge is required. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned solely for explanation and identification purposes. There is no affiliation between our company and the brands named. The offered item is original and brand-new from the manufacturer.
CNMG160616-MM5 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of high process reliability, targeted chip control and robust edge stability for consistent production results; order the insert directly via Metav Werkzeuge or consult their specialists for application support. CNMG160616-MM5 WSM20S — Turning Indexable Insert (Tiger·tec Silver) by Walter Tools The CNMG160616-MM5 WSM20S is a coated indexable turning insert designed for heavy-duty machining of stainless steels and heat-resistant alloys, offering stable edge life and optimised chip control for demanding turning operations. Tiger·tec Silver coating technology Optimised chip control MM5 geometry For stainless steels and superalloys Rhombic 80° insert, 1.6 mm corner radius Durable, heat-resistant coating for demanding alloys The Tiger·tec Silver coating and the WSM20S grade are engineered to resist thermal and mechanical stress during interrupted cuts and long turning cycles. Coating technology reduces flank wear and supports a stable cutting edge, which translates into predictable tool life and fewer regrinds. For workshops processing stainless steels and heat-resistant superalloys, this insert improves machining reliability by delaying crater formation and sustaining surface finish under elevated cutting temperatures. Controlled chip formation for safer turning operations The MM5 chipbreaker geometry has been developed to promote consistent chip segmentation and evacuation in materials that tend to form long, stringy chips. The controlled chip flow reduces the risk of chip entanglement and improves coolant access at the cutting zone, resulting in fewer interruptions and a safer shop floor. Practical benefits include smoother toolpaths, reduced secondary operations to clear chips, and enhanced cycle-time stability for series production. Geometry and edge preparation that support repeatability A rhombic 80° shape combined with a 1.6 mm corner radius delivers a balance between strength and cutting performance: the robust corner supports heavier feeds while preserving edge security, and the negative 0° relief provides a stable cutting attitude under axial loads. These geometric choices help maintain dimensional accuracy and surface integrity with each indexation, making the insert suitable for both roughing and medium finishing passes where repeatable results matter. Practical selection guidance and application scope This insert is specified for material groups M (stainless steels) and S (heat-resistant superalloys and titanium) according to ISO designation, making it a versatile choice when one grade must cover several hard-to-machine materials. The nominal size code and thickness are provided to match common toolholders; users should verify holder compatibility and cutting parameters with tooling specialists. For tailored cutting data and optimisation, Metav Werkzeuge can provide application-specific recommendations and feed/speed guidance to exploit the insert’s full potential. Contact Metav Werkzeuge for application advice on Walter Tools Tiger·tec Silver inserts and arrange a tailored tooling recommendation to improve process stability and productivity Technical data Article number: CNMG160616-MM5-WSM20S-WALTER Description: Drehwendeschneidplatte CNMG160616-MM5 WSM20S Walter Tools Manufacturer: Walter Tools Grade / Series: WSM20S / Tiger·tec Silver Core specifications ISO designation: CNMG160616-MM5 WSM20S Insert size: 16 Plate thickness code: 06 Relief angle: 0° (negative) Corner radius: 1.6 mm Insert shape: Rhombus 80° Chipbreaker: MM5 Tolerance class: M Materials & special features Material group: S / M Suitable for: stainless steels (M) and heat-resistant alloys/titanium (S) Coating technology: Tiger·tec Silver Application focus: heavy-duty and difficult-to-machine materials Indexable turning insert type: Drehwendeschneidplatte FAQ What materials is this insert designed to machine? The CNMG160616-MM5 WSM20S insert from Walter Tools is specified for stainless steels (ISO group M) and heat-resistant superalloys or titanium (ISO group S), offering an application window for demanding alloys. How does the MM5 chipbreaker help in production? The MM5 geometry promotes consistent chip segmentation and evacuation, reducing chip-related interruptions and improving process stability during longer turning cycles. What are the geometric advantages of the rhombic 80° shape? The rhombic 80° shape provides secure cutting engagement and versatility between roughing and medium finishing; combined with a 1.6 mm corner radius, it sustains edge strength under higher feed conditions. Is the coating suitable for high-temperature cutting? Yes; the Tiger·tec Silver coating on the WSM20S grade enhances thermal resistance and wear protection, helping to maintain edge life in thermally demanding operations. How to ensure compatibility with tooling systems? Confirm holder compatibility with the ISO designation CNMG160616-MM5 WSM20S and the plate thickness code; for matching toolholder and cutting data, consult Metav Werkzeuge for specific recommendations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and product names remain the property of their respective owners and are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered article is an original, factory-new product of the manufacturer.
CNMG160616-MM5 WSM30S WSM30S Wendeplatten - Walter Tools
Take advantage of the combination of durable coating technology and robust geometry for reliable machining of stainless steels and heat-resistant alloys; order directly via Metav Werkzeuge or consult our application specialists for optimised cutting data and fast delivery. Turning insert CNMG160616-MM5 WSM30S — Tiger·tec Silver, Walter Tools the CNMG160616-MM5 WSM30S turning insert offers coated-carbide performance for demanding finishing and light roughing in stainless steels and superalloys Tiger·tec Silver coating for heat resistance Optimised MM5 chipbreaker for stable chip control Negative 0° rake for high edge stability 1.6 mm corner radius for improved tool life Higher process reliability through advanced coating and grade The WSM30S grade, part of the Tiger·tec Silver family, is a coated carbide compound developed for machining stainless steels and heat-resistant superalloys. Its coating chemistry increases thermal resistance and reduces adhesion on the cutting edge, which translates directly into longer tool life and fewer interruptions in production. For manufacturers seeking consistent performance when cutting tough, work-hardened materials, this insert supports steady metal removal rates while lowering the frequency of tool changes and rework. Geometry that stabilises cutting forces and surface quality Featuring a rhombic 80° shape with a 1.6 mm corner radius and 0° (negative) rake, the insert delivers a balanced combination of strength and accessibility. The negative rake enhances edge security under heavy engagement, while the MM5 chipbreaker promotes predictable chip formation and evacuation. These geometric choices reduce vibration and help produce a uniform surface finish with minimal secondary machining. The result is a dependable turning cycle with fewer downstream corrections and consistent component tolerances. Practical advantages for shop-floor integration Designed for straightforward toolholder mounting and reproducible set-ups, this turning insert simplifies process planning for mixed-batch production. The coated carbide grade tolerates intermittent cuts and variable cutting conditions common in stainless steel work, helping to maintain cutting-edge integrity under thermal stress. Where repeatability and throughput matter, the insert supports cost-efficient machining by extending usable tool life and reducing scrap. For additional process optimisation, Metav Werkzeuge’s application engineers can provide cutting parameters tailored to specific machines and workpiece alloys. Contact Metav Werkzeuge for tailored cutting data and rapid supply of Walter Tools Tiger·tec Silver inserts at info@metav-werkzeuge.com or by phone +49 2822 7131930 Technical data SKU: CNMG160616-MM5-WSM30S-WALTER Article designation: CNMG160616-MM5 WSM30S Manufacturer: Walter Tools Core dimensions & measurable data Insert size: 16 (mm) Thickness: 06 Corner radius: 1.6 mm Shape: Rhombus 80° Rake: 0° (negative) Tolerance class: M Materials, grade & special features Grade: WSM30S Series: Tiger·tec Silver Chipbreaker: MM5 Coating: Coated carbide (Tiger·tec Silver technology) Execution code: G Suitable for: Stainless steels (M) and heat‑resistant superalloys/titanium (S) FAQ What materials is this insert intended for? The CNMG160616-MM5 WSM30S insert by Walter Tools is formulated for machining stainless steels (ISO group M) and heat‑resistant superalloys/titanium (ISO group S). Which chipbreaker and geometry are specified for this insert? This turning insert features the MM5 chipbreaker, a rhombic 80° form, a 1.6 mm corner radius and a 0° negative rake to ensure stable chip control and edge security. How does the Tiger·tec Silver coating benefit machining performance? The Tiger·tec Silver coating on the WSM30S grade improves thermal resistance and reduces adhesion at the cutting edge, enhancing tool life and process stability when turning difficult-to-cut alloys. Is this insert suitable for finishing passes on stainless steel components? Yes, the combination of the WSM30S grade and the insert geometry provides consistent surface quality and is suitable for finishing and light roughing in stainless steel applications. Can Metav Werkzeuge provide cutting parameters for specific machines? Metav Werkzeuge can supply optimised cutting data and application advice to match machine capabilities and workpiece specifications for this Walter Tools turning insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered item is original, factory-new merchandise of the manufacturer.
CNMG160616-MP5 WPP10G Wendeplatten - Walter Tools
Taking advantage of the Tiger·tec Gold coating and the MP5 chipbreaker results in longer tool life and consistent chip formation for steel turning tasks; combine these strengths with the Rhombic 80° geometry for predictable cutting behaviour and efficient production. Order directly via Metav Werkzeuge or consult our cutting-tool specialists for matching grades and stock options. CNMG160616-MP5 WPP10G indexable insert — Tiger·tec Gold, MP5 chipbreaker (Walter Tools) The CNMG160616-MP5 WPP10G is an indexable turning insert optimised for steel machining, offering robust chip control and extended wear resistance in general turning operations Tiger·tec Gold coated carbide MP5 chipbreaker for controlled chips Rhombic 80° geometry for stability 1.6 mm corner radius for reliable edge life Greater uptime through advanced coating and substrate The Tiger·tec Gold coating combined with the WPP10G grade provides enhanced wear resistance and thermal stability, which translates into longer tool life and fewer insert changes on the shop floor. This combination is specifically engineered for coated carbide performance in ISO P applications (steel), where heat and continuous cutting demand a balanced coating/substrate system. The result is reduced process interruptions and lower cost per part without compromising cutting speed. Consistent chip control and surface quality Thanks to the MP5 chipbreaker and the Rhombic 80° shape, the insert secures reliable chip formation across a range of cutting conditions, minimising built-up edge and preventing long, tangled chips in turning operations. The controlled chip flow contributes directly to a stable surface finish and simplified swarf management in automated or manual turning centres. The geometry supports predictable cutting forces, which helps maintain cycle times and repeatable part quality. Geometry tuned for demanding turning tasks The negative 0° clearance specification and the 1.6 mm corner radius deliver a robust cutting edge for interrupted cuts and medium-to-heavy turning feeds. This geometry reduces the risk of edge chipping during roughing passes while preserving acceptable finish capability in semi-finishing. The insert is designated for steel machining per ISO P, which means it is tailored to typical heat generation and chip characteristics encountered in unalloyed and alloyed steels. Practical benefits for workshop logistics and process security Presented in an industry-standard CNMG form, the insert integrates easily into existing toolholders and inventory systems, supporting rapid changeovers and consistent setup routines. Using a standardised grade such as WPP10G simplifies tool selection across multiple machines and operators, improving process security and enabling predictable replenishment planning. For technical queries or specific cutting-data recommendations, Metav Werkzeuge's application team is available to provide machining parameters and compatibility checks. Discuss Walter Tools Tiger·tec Gold solutions with Metav Werkzeuge for tailored machining recommendations and availability Technical Data Article number: CNMG160616-MP5-WPP10G-WALTER ISO designation: CNMG160616-MP5 WPP10G Product type: Drehwendeschneidplatte Manufacturer/brand: Walter Tools Facts Inscribed circle / size: 16 mm Corner radius: 1.6 mm Clearance angle: 0° (negative) Thickness code: 06 Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP10G (coated carbide) Chipbreaker: MP5 Plate shape: Rhombic 80° Application group: Steel (ISO P) FAQ What materials is this insert suited for? The CNMG160616-MP5 WPP10G insert is specified for ISO P materials, meaning it is optimised for the machining of unalloyed and alloyed steel. How does the Tiger·tec Gold coating improve performance? The Tiger·tec Gold coating on the WPP10G grade increases wear resistance and temperature tolerance, which extends life and maintains consistent cutting behaviour during continuous turning. Which chipbreaker should be chosen for general turning tasks? The MP5 chipbreaker on this insert is designed for controlled chip formation and suits a wide range of turning feeds and depths typical in roughing and semi-finishing. Is the geometry suitable for interrupted cuts? Yes, the negative 0° clearance and 1.6 mm corner radius provide a robust edge that withstands intermittent cutting conditions and reduces the risk of edge chipping. Can this insert be used in standard CNMG toolholders? The CNMG form and dimensions match industry-standard toolholder interfaces, so the insert is compatible with standard CNMG toolholders when secured and indexed correctly. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. The mention of Walter Tools relates solely to the origin of the product and explanatory purposes. The offered item is original factory-new merchandise of the manufacturer.
CNMG160616-MP5 WPP20G WPP20G Wendeplatten - Walter Tools
Benefit from Walter Tools’ Tiger·tec Gold coated carbide and the MP5 chipbreaker for efficient, repeatable steel turning with reliable chip control; order directly via Metav Werkzeuge or consult our specialists for selection and availability. CNMG160616-MP5 WPP20G indexable turning insert (Rhombic 80°, R1.6) – Walter Tools The CNMG160616-MP5 WPP20G indexable turning insert is a coated carbide solution for high-productivity steel turning, combining a Tiger·tec Gold grade with an MP5 chipbreaker for stable machining. Tiger·tec Gold coating for enhanced wear resistance WPP20G grade optimised for steel machining MP5 chipbreaker for stable chip formation Rhombic 80° insert, R1.6 corner radius High productivity for steel turning operations The combination of a coated carbide substrate and the WPP20G grade makes this insert particularly suited to the demands of ISO P applications. The grade is engineered for general-purpose steel machining with an emphasis on stable chip formation and broad material coverage, which translates into fewer interruptions on the machine and improved cycle times. Tolerance class M supports consistent positioning in approved toolholders, contributing to process reliability and reduced downtime in serial production. Consistent chip control and surface integrity The integrated MP5 chipbreaker and the Rhombic 80° geometry work together to manage chip flow effectively. Controlled chip evacuation reduces the risk of built-up edge and prevents chip re-cutting, which preserves flank and crater conditions. The 1.6 mm corner radius increases edge strength and helps maintain a consistent surface finish when finishing or semi-finishing steel parts. For operators and process engineers, improved chip control often means longer uninterrupted runs and fewer manual interventions. Coating technology and edge security for longer tool life The insert’s Tiger·tec Gold technology provides a multi-layer coating system that improves thermal stability and wear resistance under the heat and abrasion typical of steel turning. The negative 0° rake increases edge robustness, permitting more aggressive feeds where required while maintaining reliable tool life. These properties reduce flank wear and help preserve dimensional accuracy over multiple workpieces, supporting predictable tool-change intervals and easier planning of maintenance cycles. Integration into the machining process and application notes Designed for standard CNMG toolholders, the insert’s dimensions (size 16) and geometry suit a wide range of turning tasks in steel fabrication and component production. The configuration is optimised for productive machining rather than specialised exotic materials; suitability is defined for steel (ISO P). Further assistance with cutting data, clamping recommendations or process optimisation is available; Metav Werkzeuge can supply specific parameters and compatibility guidance to match the insert to existing tool systems and workholding. Contact Metav Werkzeuge for availability and tailored recommendations on Walter Tools' CNMG160616-MP5 WPP20G inserts: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: CNMG160616-MP5-WPP20G-WALTER Article: CNMG160616-MP5 WPP20G Type: Indexable turning insert Manufacturer: Walter Tools Facts Insert size: 16 Corner radius: 1.6 mm Free angle: 0° (negative) Thickness code: 06 Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP20G Chipbreaker: MP5 Shape: Rhombic 80° Material: Coated carbide Application: Steel (ISO P) FAQ What materials is this insert suited for? The CNMG160616-MP5 WPP20G insert from Walter Tools is specified for machining steel (ISO P) and is optimised for the thermal and chip-formation characteristics typical of these materials. What is the benefit of the MP5 chipbreaker? The MP5 chipbreaker on this Walter Tools insert controls chip shape and evacuation to promote stable cutting, reduce built-up edge and support longer uninterrupted machining cycles. Which geometry and corner radius does the insert feature? This indexable insert has a Rhombic 80° form with a 1.6 mm corner radius, providing a balance of edge strength and surface finish for turning operations. Is the insert coated and how does the coating help? The CNMG160616-MP5 WPP20G uses Tiger·tec Gold coating technology, which enhances wear resistance and thermal stability to extend tool life and maintain consistent performance. What tolerance and clamping considerations apply? Tolerance class M enables repeatable seating in standard CNMG toolholders; correct clamping and seat cleanliness are essential for the Walter Tools insert to achieve specified repeat accuracy. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered item is original, factory-new goods of the manufacturer (Walter Tools).
CNMG160616-MP5 WPP30G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and an MP5 chipbreaker for reliable chip control and extended tool life; the rhombic 80° geometry with a 1.6 mm nose radius delivers consistent surface finish and stable cuts. Order this insert directly via Metav Werkzeuge or contact our advisors for application guidance and a tailored quotation. CNMG160616-MP5 WPP30G indexable turning insert — Tiger·tec Gold, MP5 chipbreaker | Walter Tools The CNMG160616-MP5 WPP30G is a rhombic 80° indexable insert for steel turning, designed to combine reliable chip formation with robust edge life in general-purpose and demanding operations Tiger·tec Gold coated carbide Optimised MP5 chipbreaker 1.6 mm nose radius for precision Negative 0° rake for stable cuts Proven coating for longer edge life and process stability The Tiger·tec Gold coating paired with the WPP30G grade produces a wear-resistant, coated carbide cutting edge that is engineered for the heat and chip formation typical of steel turning. As a result, the insert provides consistent tool life and improved resistance to abrasive wear, reducing the frequency of tool changes and helping to maintain steady production throughput. The coating technology also supports more predictable performance across a range of cutting conditions, which translates into fewer interruptions and greater process reliability. Geometry and chip control that improve surface finish The rhombic 80° form and the MP5 chipbreaker are engineered to manage chips effectively while maintaining a secure cutting edge. The combination of a 1.6 mm corner radius and a 0° (negative) relief angle gives a balance between strength at the cutting edge and the ability to achieve good surface integrity. These geometric choices reduce vibration and enable stable cutting forces, which helps to attain repeatable surface quality and dimensional accuracy on turned components. Broad applicability for steel machining and productivity gains Designed specifically for the machining of the P material group (steel), the insert is suitable for a wide spectrum of steel types—from more wear-resistant steels to universal and tougher grades—thanks to the WPP30G grade characteristics. The standardised CNMG form supports fast index changes and simple inventory handling for insertion-based tooling systems. This adaptability contributes to higher uptime and a leaner tooling setup on the shop floor, supporting both batch production and continuous operations. Operational benefits: handling, tolerances and compatibility The CNMG16 size and the 06 thickness code fit common toolholders and clamping systems, while the tolerance class M indicates consistent dimensional accuracy for reliable seating and repeatable cuts. The insert’s MP5 chip control and the Tiger·tec Gold technology combine to reduce flank wear and promote stable cutting conditions, which can lower overall tooling costs through longer useful life and fewer interruptions for insert replacement. The design supports straightforward integration into established turning processes with minimal adjustment. Contact Metav Werkzeuge for application advice and to request a tailored quotation for Walter Tools CNMG160616-MP5 WPP30G indexable inserts — eMail: info@metav-werkzeuge.com • Phone: +49 2822 7131930 Technical data SKU: CNMG160616-MP5-WPP30G-WALTER ISO designation: CNMG160616-MP5 WPP30G Product type: indexable turning insert Brand: Walter Tools Core measurements Size: 16 Thickness code: 06 Corner radius: 1.6 mm Relief angle: 0° (negative) Tolerance class: M Materials & special features Coating: Tiger·tec Gold Grade: WPP30G (coated carbide) Chipbreaker: MP5 Shape: Rhombic 80° Material application: steel (P) FAQ What steels is this insert suitable for? The WPP30G grade on the CNMG160616-MP5 insert is formulated for the P material group and is suitable for unalloyed and alloyed steels across a broad hardness and toughness range. How does the MP5 chipbreaker affect machining? The MP5 chipbreaker on this insert promotes controlled chip formation and evacuation, improving process stability and helping to maintain surface finish during turning operations. Can the rhombic 80° form be used for light finishing passes? Yes, the rhombic 80° geometry with a 1.6 mm corner radius provides a good compromise between strength and finish capability, making it suitable for both general turning and finishing tasks. Is the Tiger·tec Gold coating beneficial for high-feed or roughing cuts? The Tiger·tec Gold coating enhances wear resistance and edge stability under elevated temperatures and abrasive conditions commonly encountered in roughing; it therefore supports robust performance in demanding cuts. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between our company and the named brands. The offered item is original, factory-new merchandise of the manufacturer.
CNMG160616-MU5 WPP05G Wendeplatten - Walter Tools
Combining the Tiger‑tec Gold coating with the MU5 chipbreaker and a 1.6 mm corner radius delivers reliable, repeatable turning performance in steel machining; purchase guidance and application support are available from Metav Werkzeuge. CNMG160616-MU5 WPP05G turning insert – Tiger‑tec Gold, Walter Tools A CNMG160616-MU5 WPP05G turning insert designed for robust steel turning, pairing the Tiger‑tec Gold coated carbide grade with a MU5 chipbreaker for stable chip formation. Tiger‑tec Gold coated carbide grade WPP05G MU5 chipbreaker for stable chip control Rhombic 80° insert with 1.6 mm corner radius 0° negative clearance for robust cutting Engineered for consistent steel turning performance The Tiger‑tec Gold coating and the WPP05G grade combine to offer enhanced wear resistance and consistent edge life when machining steel, which is the intended application for this insert. The coating technology is optimised to reduce abrasive wear and to maintain a stable cutting edge over longer cycles; this translates into fewer insert changes and higher uptime on component production runs. The rhombic 80° geometry ensures good cutting face support while the 1.6 mm corner radius provides a balance between edge strength and achievable surface finish, making the insert suitable for standard to moderately heavy turning operations. Reliable chip control for uninterrupted production The MU5 chipbreaker is engineered to produce short, predictable chips when cutting steel, reducing the risk of long, tangled swarf that can interrupt automated processes. Short chip form reduces the need for frequent stoppages to clear chips and improves tool-to-part contact stability. The 0° negative clearance configuration increases insert robustness for interrupted cuts or heavy depth engagements, offering process security where consistent metal removal and machine reliability are priorities. Durability and edge security for stable process results Constructed from a coated carbide grade within the Tiger‑tec Gold family, the insert is tuned for a broad range of steel turning tasks, prioritising stable flank and crater wear behaviour. This material combination supports repeatable tolerances and a reliable surface finish over long tool life, which is particularly relevant for batch production or mixed-series machining where reproducibility matters. The insert form and thickness correspond to standard CNMG proportions, providing mechanical support that reduces chipping risk under tougher cutting conditions. Practical use and integration into machining workflows The insert integrates easily into existing toolholders that accept CNMG‑style inserts, enabling quick indexation and straightforward replacement. For process planning, consider the MU5 chipbreaker for general finishing to medium‑roughing operations in steel where controlled chip shapes and reliable edge life are required. For newcomers to indexable tooling, the coating and chipbreaker combination simplifies parameter selection: focus on stable feeds and speeds within machine and workpiece limits to benefit from the insert’s wear properties and chip control. Contact Metav Werkzeuge for application advice on using the Walter Tools CNMG160616-MU5 WPP05G insert in steel turning and to discuss suitable cutting data and supply options; Metav Werkzeuge can provide technical consultation and ordering support via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: CNMG160616-MU5-WPP05G-WALTER Type designation: CNMG160616-MU5 WPP05G Product type: Turning insert Manufacturer: Walter Tools Data Inscribed size: 16 Thickness: 06 Corner radius: 1.6 mm Insert angle: Rhombic 80° Clearance: 0° (negative) Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WPP05G Chipbreaker: MU5 Coating: Tiger‑tec Gold coated carbide Recommended application: Steel machining FAQ What materials is this insert intended for? The CNMG160616-MU5 WPP05G insert is designed primarily for steel machining; the WPP05G grade and Tiger‑tec Gold coating are optimised for typical heat and chip formation when turning unalloyed and alloyed steels. How does the MU5 chipbreaker influence machining? The MU5 chipbreaker delivers controlled, short chip forms in steel cutting applications, improving process continuity and reducing the likelihood of chip-related interruptions during production with the CNMG160616-MU5 WPP05G insert. Can this insert handle interrupted cuts or heavy engagements? Yes, the 0° negative clearance and the robust geometry of this CNMG insert increase resistance to chipping and mechanical shock, making it suitable for interrupted cuts and tougher engagement conditions. Is this insert compatible with standard CNMG toolholders? The CNMG160616-MU5 WPP05G is compatible with toolholders designed for CNMG‑style inserts; correct clamping and seat condition are essential to achieve the expected performance and repeatability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for clarification and identification only; there is no affiliation between our company and the trademark owners. The offered item is an original, factory‑new product of the respective manufacturer.
CNMG160616-MU5 WPP10G WPP10G Wendeplatten - Walter Tools
Combining the Tiger·tec Gold coating and the WPP10G grade delivers high wear resistance and consistent edge life, while the MU5 chipbreaker and 1.6 mm corner radius ensure stable cutting in Stahl turning. Order the CNMG160616-MU5 WPP10G directly via Metav Werkzeuge or consult the specialists for application advice. CNMG160616-MU5 WPP10G indexable turning insert — Tiger·tec Gold grade for Stahl | Walter Tools The CNMG160616-MU5 WPP10G is a coated indexable turning insert engineered for robust Stahl turning, featuring a MU5 chipbreaker and a rhombic 80° geometry for versatile turning operations Tiger·tec Gold coating for high wear resistance Optimised MU5 chipbreaker for Stahl chip control Rhombic 80° geometry for versatile turning 1.6 mm corner radius for cutting stability 0° negative rake for heavy-duty cuts High productivity through optimised grade and coating The combination of the WPP10G grade and the Tiger·tec Gold coating provides a balance of wear resistance and toughness that supports longer tool life under continuous production. For machining Stahl, this coated carbide solution reduces flank wear and helps maintain consistent tolerances. The result is fewer tool changes and improved uptime, which supports a predictable production rhythm and better cost-efficiency per component. The coating technology is designed to withstand the heat and abrasion typical for P‑group applications, so cycle times remain productive without compromising edge integrity. Stable cutting and reliable chip control for process safety The integrated MU5 chipbreaker and the 1.6 mm corner radius work together to deliver consistent chip formation and safer evacuation during turning. The MU5 geometry is tailored to the thermal and metallurgical behaviour of Stahl, producing manageable chips even in medium to heavy cuts; this reduces risk of re-cutting and tool damage. The 0° negative rake increases edge strength for interrupted cuts and tough materials, while the rhombic 80° design provides flexible approach angles for a variety of turning tasks. These combined features enhance process stability and contribute to repeatable part quality. Application guidance and material compatibility Designed for ISO P applications, the insert is primarily suited to unalloyed and alloyed Stahl where moderate to high cutting forces occur. The rhombic 80° shape and the insert size make it suitable for both general turning and semi-finish operations, while the MU5 chipbreaker helps improve surface integrity where consistent chip control is required. For finishing steps that demand fine surface quality, selecting appropriate feeds and speeds in line with the WPP10G recommendations will yield optimal results. The coated carbide composition offers a robust compromise between hardness and toughness, enabling use across a broad range of Stahl grades. Contact Metav Werkzeuge for tailored application recommendations and fast availability of Walter Tools Tiger·tec Gold inserts — specialists can advise on cutting data and batch supply to match production needs. Technical Data Article number: CNMG160616-MU5-WPP10G-WALTER Designation: CNMG160616-MU5 Full identification: CNMG160616-MU5 WPP10G Manufacturer: Walter Tools Series: Tiger·tec Gold Data Size: 16 Thickness: 06 Corner radius: 1.6 mm Free rake: 0° (negative) Insert shape: Rhombus 80° Chipbreaker: MU5 Tolerance class: M Special features Grade: WPP10G (Tiger·tec Gold) Coated carbide MU5 chipbreaker optimised for Stahl Suitable for Stahl (ISO P) Rhombic 80° geometry Series: Tiger·tec Gold FAQ What materials is this insert designed for? The CNMG160616-MU5 WPP10G is designed primarily for Stahl (ISO P) applications, covering unalloyed and alloyed steels with a focus on stable chip formation. What does the WPP10G grade indicate? WPP10G is a Walter Tools coated carbide grade from the Tiger·tec Gold family that balances wear resistance and toughness for productive Stahl turning. How does the MU5 chipbreaker improve performance? The MU5 chipbreaker on this insert promotes controlled chip formation for Stahl, reducing the risk of entanglement and improving surface consistency during turning. Is the insert suitable for interrupted cuts or heavy cutting? Yes; the 0° negative rake and the 1.6 mm corner radius provide increased edge strength, making the insert suitable for interrupted and heavier turning operations. Can this insert be used for finishing operations? The rhombic 80° geometry and the coated carbide composition allow the insert to be used for semi-finish and certain finishing tasks when paired with appropriate feeds, speeds and toolholder rigidity. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names are used for explanatory purposes only and do not imply any affiliation between Metav Werkzeuge and the trademark holders. The offered item is original, brand-new factory product from the stated manufacturer.
CNMG160616-MU5 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a MU5 chipbreaker and a 1.6 mm corner radius for reliable steel machining and long tool life; order directly via Metav Werkzeuge or consult our specialists for process integration. CNMG160616-MU5 WPP20G Drehwendeschneidplatte — Rhombus 80°, Tiger·tec Gold, for steel — Walter Tools The CNMG160616-MU5 WPP20G is a rhombic 80° turning insert designed for general steel applications, combining a coated carbide grade with a MU5 chipbreaker for consistent chip formation and extended productivity. Tiger·tec Gold coating for improved tool life Designed for steel machining (ISO group P) Rhombic 80° shape for versatile turning 1.6 mm corner radius with MU5 chipbreaker Longer production runs with reduced tool changes The coated carbide grade from the Tiger·tec Gold series is engineered to deliver consistent wear resistance under the thermal and mechanical loads typical of steel turning. By combining a robust coating technology with a universal, wear-resistant substrate, the insert offers a predictable service life that helps reduce unplanned tool changes and downtime. This benefit translates into more stable cycle times and improved machine utilisation during medium- to high-volume turning operations. Reliable chip control and process stability The MU5 chipbreaker geometry promotes controlled chip formation when working with unalloyed and alloyed steel, lowering the risk of tangled chips and improving surface finish stability. In practical terms, the chip control reduces interruptions and eases parts handling in automated and manual setups alike. The negative 0° rake contributes to a secure cutting edge in heavier cuts, enhancing process security where robust engagement is required. Geometry crafted for versatile turning tasks The rhombic 80° form factor and a 1.6 mm corner radius deliver a balance between edge strength and profile accuracy. This geometry is especially useful where a blend of roughing and finishing is needed without frequent insert changes. The plate thickness and ISO CNMG designation support a wide range of toolholder options, simplifying retrofit into existing turning toolchains and enabling flexible setup changes with minimal tooling overhead. Practical integration and material suitability Intended primarily for machining steels (ISO group P), this insert suits operations that prioritise repeatable cutting performance and easy process definition. The coated carbide construction stands up well to typical steel heat generation and chip behaviour, so it is appropriate for both conventional lathes and CNC centres. For workshops seeking to standardise on a single insert grade across varied component geometries, the combination of coating, chipbreaker and corner radius offers a pragmatic compromise between life and edge strength. Discuss Walter Tools Tiger·tec Gold options with Metav Werkzeuge to optimise turning processes and material throughput — our specialists will advise on insert selection and process parameters for steel applications Technical data SKU: CNMG160616-MU5-WPP20G-WALTER Label: Drehwendeschneidplatte CNMG160616-MU5 WPP20G Walter Tools Manufacturer: Walter Tools Product type: Drehwendeschneidplatte Series: Tiger-tec Gold Grade / Sort: WPP20G Core specifications Insert form: Rhombus 80° Insert size: 16 Corner radius: 1.6 mm Thickness: 06 Rake angle: 0° (negative) Chipbreaker: MU5 Tolerance class: M Design and materials Coating / technology: Tiger·tec Gold (coated carbide) Substrate / grade: coated cemented carbide Material application: Steel (ISO group P) Execution: G FAQ What materials is this insert suitable for? The CNMG160616-MU5 WPP20G insert is specified for machining steels (ISO group P) and is designed to handle the heat and chip characteristics associated with unalloyed and alloyed steel. How does the MU5 chipbreaker affect machining performance? The MU5 chipbreaker promotes controlled chip formation and reduced chip entanglement during steel turning, which improves process stability and surface quality when using the CNMG160616-MU5 WPP20G insert. What benefits does the Tiger·tec Gold coating provide? Tiger·tec Gold coating on this insert increases wear resistance and extends tool life under typical steel cutting conditions, supporting longer uninterrupted production runs. Is the 1.6 mm corner radius suitable for finishing operations? A 1.6 mm corner radius provides enhanced edge strength while still allowing acceptable surface finishes for semi-finishing and certain finishing passes with appropriate cutting parameters on this insert. Can existing toolholders accept this CNMG insert? The CNMG designation corresponds to a widely used insert geometry and is compatible with standard toolholders designed for rhombic 80° CNMG plates, facilitating integration into existing tooling systems. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original, brand-new goods of the manufacturer.
CNMG160616-NRS WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and a robust negative geometry to secure stable chip formation and extended tool life; order or request application support via Metav Werkzeuge for seamless integration into production. CNMG160616-NRS WSM10S – Turning insert, Tiger·tec Silver grade, Walter Tools The CNMG160616-NRS WSM10S is a rhombic 80° turning insert engineered for demanding applications, optimised for machining rostfreier Stahl and heat‑resistant superalloys with a focus on reliable chip control and edge stability Tiger·tec Silver coating for improved tool life Optimised for rostfreier Stahl and superalloys Rhombic 80° form with 1.6 mm corner radius Negative 0° rake for robust cutting Coating and substrate designed for consistent performance The combination of the Tiger·tec Silver coating and a coated carbide substrate provides a balance of thermal resistance and wear protection that supports continuous production. The coating technology reduces built‑up edge and improves chip control, which directly lowers rework rates and enhances process predictability. Explained simply: the surface layer resists heat and adhesion, while the carbide core maintains edge strength, so the tool sustains cutting forces in long cycles without rapid deterioration. Geometry that favours secure cutting and repeatability Engineered geometry delivers tangible production benefits. The Rhombic 80° shape and a 1.6 mm corner radius give a stable cutting edge for interrupted or heavy cuts, while the negative 0° rake increases mechanical strength at the cutting zone. The NRS chipbreaker supports controllable chip formation across a range of feeds, reducing the risk of snarled chips and enabling safer, more predictable machining. As a result, cycle times remain consistent and tool change intervals become more reliable. Application scope: tailored for rostfreier Stahl and heat‑resistant alloys This grade (WSM10S) is specifically targeted at ISO groups M and S — rostfreier Stahl and heat‑resistant superalloys/titanium — where heat generation and material toughness place high demands on the cutting edge. The insert’s thermal resilience and edge stability help avoid common issues such as built‑up edge, notch wear and thermal softening. For workshops processing surgical components, aerospace parts or automotive exhaust components, this insert supports higher process stability when machining difficult-to-cut materials. Productivity and cost-efficiency through process security Selecting a grade designed for demanding materials reduces unplanned downtime. The WSM10S grade and Tiger·tec Silver series aim to produce a stable cutting edge and consistent wear behaviour, which translates into predictable tool life and lower overall tooling costs per part. In practice, fewer variances in insert performance mean less time spent adjusting feeds and speeds and more uptime on CNC turning centres. Where throughput and repeatability matter, the combination of coating and geometry provides measurable economic advantages. For tailored application advice on Walter Tools Tiger·tec Silver inserts and to discuss suitable tooling strategies, contact Metav Werkzeuge for professional recommendations and delivery options Technical data SKU: CNMG160616-NRS-WSM10S-WALTER Name: Drehwendeschneidplatte CNMG160616-NRS WSM10S Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WSM10S Chipbreaker: NRS Shape: Rhombic 80° Rake angle: 0° (negative) Corner radius: 1.6 mm Plate size: 16 Thickness code: 06 Tolerance class: M Facts Corner radius: 1.6 mm Plate size: 16 mm Rake angle: 0° (negative) Thickness code: 06 Tolerance class: M Special features Coated carbide grade Tiger·tec Silver Design optimised for rostfreier Stahl (ISO M) and superalloys/titanium (ISO S) NRS chipbreaker for controlled chip formation Rhombic 80° plate geometry Robust cutting edge for interrupted cuts Walter Tools product family Tiger·tec Silver FAQ Is this insert suitable for rostfreier Stahl (stainless steel)? Yes. The CNMG160616-NRS WSM10S is designed for rostfreier Stahl (ISO group M), offering coating and edge stability that counteracts built‑up edge and heat‑related wear. Can this grade be used on titanium or superalloys? The WSM10S grade supports ISO group S applications; its thermal resistance and chip control reduce edge loading when machining heat‑resistant superalloys and titanium. What cutting geometry helps with interrupted cuts? The rhombic 80° form and a 1.6 mm corner radius provide a strong cutting edge for interrupted and heavy cuts; the negative 0° rake increases mechanical robustness. How does the NRS chipbreaker affect machining? The NRS chipbreaker promotes short, controllable chips across common feed ranges, improving process safety and reducing chip-related downtime with this Walter Tools insert. Which toolholders are compatible with the CNMG160616-NRS WSM10S? This insert matches standard CNMG toolholders with the corresponding seat for rhombic 80° inserts; verify holder compatibility by position and clamping system on the lathe. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160616-NRS WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver robustness and a reliable NRS chipbreaker to ensure stable cutting in stainless and heat‑resistant alloys; order directly via Metav Werkzeuge or contact the technical team for application advice. CNMG160616-NRS WSM20S indexable turning insert — Tiger·tec Silver for stainless steels and superalloys | Walter Tools A CNMG160616-NRS WSM20S indexable turning insert engineered for interrupted and continuous turning of rostfreie Stähle and heat‑resistant superalloys in demanding production environments. Tiger·tec Silver coating for heat resistance Designed for stainless steels and superalloys Rhombic 80° geometry for versatile turning NRS chipbreaker with 1.6 mm corner radius Reliable machining of high‑alloy materials The combination of the WSM20S grade within the Tiger·tec Silver family delivers enhanced thermal resistance and wear behaviour when machining stainless steels and heat‑resistant alloys. This coated carbidesort is optimised to reduce flank wear and to maintain a stable cutting edge during long cycles, which supports consistent component quality. For operations that struggle with heat‑related adhesion or edge build‑up, the specified coating technology improves tool life and reduces unplanned tool changes, translating directly into higher machine availability and lower per‑part costs. The supplied geometry is suited to applications where secure chip formation and dependable surface finish are required. Consistent chip control and edge stability for fewer process interruptions The integrated NRS chipbreaker and the 1.6 mm corner radius promote controlled chip formation and evacuate material reliably at typical turning feeds. A negative 0° relief helps stabilise the cut under heavy engagement, reducing vibration and the risk of chipping in tough materials. These design elements combine to produce repeatable tool performance and predictable wear patterns, which is crucial for planning tool replacement intervals and minimising scrap. Understanding chipbreaker function: it shapes the chip to break into short, manageable lengths, improving safety and allowing closer tool‑to‑part proximity in automated setups. Productivity and process security in production The rhombic 80° insert shape provides flexibility in approach angles and enables multiple cutting edges per insert, supporting economical use in batch production. As an indexable insert, it allows quick edge changes without regrinding, shortening downtime and increasing throughput. The geometry and grade are selected to balance toughness and wear resistance, offering repeatable results and improved surface integrity on turned parts. Combined with the brand consistency of Walter Tools, this insert is suitable for workshops and OEMs seeking predictable output and reduced process variance. For reliable machining of stainless steels and superalloys with Walter Tools’ Tiger·tec Silver inserts, contact Metav Werkzeuge for ordering and application support: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number / SKU: CNMG160616-NRS-WSM20S-WALTER Designation: CNMG160616-NRS WSM20S Series/grade: Tiger·tec Silver WSM20S Manufacturer: Walter Tools Core figures Corner radius: 1.6 mm Plate size: 16 Relief/clearance: 0° (negative) Thickness code: 06 Design and features Chipbreaker: NRS Geometry: Rhombic 80° Coating: Tiger·tec Silver (coated cemented carbide) Material suitability: rostfreie Stähle; heat‑resistant superalloys Application type: indexable turning insert FAQ What materials is this insert suitable for? The CNMG160616-NRS WSM20S insert is designed primarily for rostfreie Stähle (stainless steels) and heat‑resistant superalloys, offering stable cutting and improved wear resistance in those groups. How does the NRS chipbreaker improve production? The NRS chipbreaker on this indexable turning insert shapes and breaks chips into short lengths, which enhances chip evacuation and reduces the risk of entanglement, supporting safer and more efficient machining. What does the 0° (negative) relief angle mean for cutting? A negative 0° relief increases insert strength under heavy cuts and interrupted turning; this geometry reduces vibration and supports a robust cutting edge in demanding operations. Can the insert be re‑indexed to use multiple cutting edges? Yes, the rhombic 80° form and indexable design allow multiple edges to be rotated into service, making the CNMG160616-NRS WSM20S an economical choice for batch and serial production. Is this product suitable for automated or long cycle machining? The combination of Tiger·tec Silver coating and the stable geometry provides repeatable tool life and process security, making the insert well suited to automated and long‑run turning operations. Walter Tools / Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160616-RM5 WMP20G RM5 Wendeplatten - Walter Tools
The combination of Tiger‑tec Gold wear resistance, a defined 1.6 mm corner radius and the RM5 chipbreaker delivers reliable performance when machining stainless steel; this reduces downtime and secures consistent surface quality. Order the insert directly via Metav Werkzeuge or consult their specialists for cutting data and application advice. CNMG160616-RM5 WMP20G — Turning insert for stainless steel, Tiger‑tec Gold (Walter Tools) The CNMG160616-RM5 WMP20G is a rhombic 80° turning insert engineered for stable chip control and long tool life when machining stainless steel under medium to robust cutting conditions. Tiger·tec Gold coating for extended life RM5 chipbreaker for secure chip formation Rhombic 80° geometry for versatile turning 1.6 mm corner radius for reproducible edge strength Consistent process performance for stainless steel The coated carbide grade WMP20G from the Tiger‑tec Gold family is designed to address the typical challenges of machining stainless steel, notably material toughness and heat generation. With its coated hardmetal structure and optimised surface treatment, the grade supports a stable cutting edge and reduced tendency to build up material on the flank. For production environments this means fewer unplanned tool changes and improved component repeatability, translating into higher throughput and lower overall machining cost. Secure chip control and long edge life The combination of the RM5 chipbreaker and the rhombic 80° geometry offers predictable chip formation in turning operations. The insert’s negative 0° clearance geometry helps absorb cutting forces in heavy cuts, while the 1.6 mm corner radius provides mechanical strength at the cutting edge. These characteristics result in reliable chip evacuation, reduced vibration and consistent surface finish — advantages that benefit workshop productivity and downstream processes such as grinding or assembly. Practical integration and predictable results on the shop floor This indexable insert is suitable for a wide range of turning tasks where stainless steel is involved, from semi-finishing to robust roughing passes. Its standard CNMG outline ensures compatibility with common toolholders, simplifying inventory and tool changeover. Technical teams can use the predictable wear behaviour of the insert to plan tool life cycles and establish cutting data windows, improving process stability and making production planning more reliable. Contact Metav Werkzeuge for application-specific cutting data and to order Walter Tools CNMG160616-RM5 WMP20G inserts, or request tailored advice for stainless steel turning operations. Technical Data Article number: CNMG160616-RM5-WMP20G-WALTER Designation: CNMG160616-RM5 WMP20G Manufacturer: Walter Tools Product type: Turning insert Facts Geometry: Rhombic 80° Corner radius: 1.6 mm Plate size: 16 mm Thickness: 0.6 mm (designation 06) Relief angle: 0° (negative) Special features Grade: WMP20G (Tiger‑tec Gold) Chipbreaker: RM5 Coated hardmetal (Tiger‑tec Gold technology) Suited for machining stainless steel (material group M) Robust edge for medium to heavy cutting conditions FAQ What materials is this insert suitable for? The CNMG160616-RM5 WMP20G insert is specified for machining stainless steel (material group M) and performs reliably under medium to robust cutting conditions. How does the RM5 chipbreaker affect cutting performance? The RM5 chipbreaker ensures secure chip formation and evacuation in turning operations, improving surface quality and lowering the risk of built-up edge when machining stainless steel. What advantage does the Tiger‑tec Gold technology provide? Tiger‑tec Gold coating on the WMP20G grade increases wear resistance and edge stability, extending tool life and supporting consistent component quality. Is the insert compatible with standard CNMG toolholders? Yes, the rhombic 80° CNMG form is compatible with common indexable insert holders, simplifying integration and inventory management. What cutting tasks is the insert best for? The insert is suitable for semi-finishing to roughing operations where a robust edge and good chip control are required when machining stainless steel. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160616-RM5 WMP30G WMP30G Wendeplatten - Walter Tools
Take advantage of a Tiger·tec Gold grade that is optimised for stainless steels and a reliable RM5 chipbreaker that ensures consistent chip formation; the combination of durable coated carbide and a rhombic 80° geometry with a 1.6 mm corner radius supports predictable tool life and stable machining. Order the CNMG160616-RM5 WMP30G insert directly via Metav Werkzeuge or ask our consultants if needed. CNMG160616-RM5 WMP30G indexable turning insert — Tiger·tec Gold, for stainless steel (Walter Tools) The CNMG160616-RM5 WMP30G is a negative‑rake, rhombic 80° turning insert designed for machining stainless steel under medium to robust conditions, featuring the Tiger·tec Gold coating technology. Tiger·tec Gold coating for extended life Optimised for stainless steel (ISO M) RM5 chipbreaker for stable chip control 1.6 mm corner radius with rhombic 80° geometry Longer tool life and material-adapted grade for stainless steel The insert’s main advantage is its coated‑carbide Tiger·tec Gold grade, WMP30G, which is formulated for the challenges of machining stainless steel. Coated grades of this class combine a wear‑resistant substrate with a multi‑layer surface treatment to reduce adhesion and thermal softening at the cutting edge. The result is a more consistent edge condition when machining tough, heat‑prone materials, leading to fewer interruptions for edge dressing and longer effective tool life. This makes the insert a cost‑efficient choice where process stability and repeatable component quality are required. Predictable chip control and cutting stability in demanding operations The integrated RM5 chipbreaker is optimised to promote compact, manageable chips during turning operations, reducing the risk of entanglement and improving surface finish. Combined with the 1.6 mm corner radius, the insert provides increased edge strength for interrupted cuts or heavier depths of cut, while the 0° (negative) free angle supports a robust cutting geometry that resists built‑up edge formation. These features translate into fewer stoppages for chip clearing and a lower likelihood of edge chipping, which helps maintain cycle times and part consistency in production environments. Practical benefits for workshop integration and process reliability The rhombic 80° geometry and the CNMG format support a wide range of turning setups and toolholder systems, enabling quick indexation and straightforward inventory management. As a coated carbide insert in the Tiger·tec Gold family, it is suited for medium to heavy cutting regimes in ISO group M applications; users can therefore expect balanced performance between wear resistance and toughness. For parts requiring reproducible surface quality and dimensional control, this insert provides a reliable compromise between productivity and tool life, backed by Walter Tools’ quality standards. For application advice on Walter Tools Tiger·tec Gold inserts or to check availability of the CNMG160616-RM5 WMP30G, contact Metav Werkzeuge for personalised consultation and ordering support via info@metav-werkzeuge.com or +49 2822 7131930. Technical data SKU: CNMG160616-RM5-WMP30G-WALTER Designation: CNMG160616-RM5 WMP30G Product type: Drehwendeschneidplatte (indexable turning insert) Brand: Walter Tools Facts Insert size: 16 mm Thickness: 0.6 mm Corner radius: 1.6 mm Geometry: Rhombus 80° Free angle: 0° (negative) Tolerance class: M Special features Series: Tiger·tec Gold Grade: WMP30G (coated carbide) Chipbreaker: RM5 Application: Suitable for stainless steel (ISO group M) Negative rake geometry for robust cutting FAQ What materials is this insert designed for? The CNMG160616-RM5 WMP30G insert is designed primarily for stainless steel (ISO M), offering stable chip formation and resistance to built‑up edge in those materials. How does the RM5 chipbreaker benefit machining? The RM5 chipbreaker on the CNMG160616‑RM5 WMP30G produces compact chips and improves surface finish while reducing the need for manual chip management during turning operations. Can the insert withstand interrupted cuts? Yes; the 1.6 mm corner radius and the negative‑rake geometry provide increased edge strength, making the insert suitable for interrupted cuts and heavier engagement in many turning applications. Which series and coating technology does this grade use? This insert belongs to the Tiger·tec Gold series and uses the coated‑carbide WMP30G grade, optimised for process reliability in stainless steel machining. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik‑Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160616-RM5 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating and the WSM20S grade for secure chip formation and extended tool life; order the CNMG160616‑RM5 WSM20S inserts via Metav Werkzeuge or consult their specialists for cutting data and application advice. CNMG160616‑RM5 WSM20S indexable turning insert — Walter Tools, Tiger‑tec Silver, for stainless steels and superalloys CNMG160616‑RM5 WSM20S is a rhombic‑80° indexable insert designed for heavy, heat‑resistant materials and stainless steels, combining a robust geometry with Tiger‑tec Silver coating for productive turning. Tiger‑tec Silver coated grade WSM20S Optimised RM5 chipbreaker for stable chips Suitable for stainless steels and superalloys Rhombus 80° form with 1.6 mm edge radius Higher process reliability through coating and grade choice The combination of the Tiger‑tec Silver coating and the WSM20S cemented‑carbide grade is engineered for demanding turning operations on stainless steels and superalloys. Coating technology reduces heat at the cutting zone and stabilises the cutting edge, which results in improved tool life and consistent surface quality under thermal load. The RM5 chipbreaker is configured to control chip shape and evacuation, which lowers the risk of built‑up edge and supports uninterrupted material removal in serial production. Geometry tuned for robust cutting and predictable results A rhombic 80° insert form with negative rake 0° and a 1.6 mm corner radius delivers a balance between cutting‑edge strength and controlled cutting action. The geometry is suited to interrupted cuts and applications where edge toughness is key; the negative rake supports a durable cutting edge while the defined corner radius helps maintain dimensional stability. These design choices translate into fewer tool changes and more consistent cycle times in workshop environments where repeatability matters. Practical selection and machining guidance for reliable integration This insert is intended for use in conventional insert toolholders for turning; when combined with correct feeds and speeds, the RM5 chipbreaker helps to produce short, manageable chips and predictable tool wear. For the machining of heat‑resistant alloys and titanium, the grade’s heat resistance and edge stability reduce the likelihood of premature flank wear. Selection of coolant strategy and cutting parameters influences the outcome significantly; cutting data adjustments are recommended based on workpiece condition and machine rigidity. For tailored recommendations, Metav Werkzeuge can provide application‑specific data and optimisation tips. Contact Metav Werkzeuge for tailored cutting data and application advice for Walter Tools Tiger‑tec Silver inserts and ensure the right insert selection for production demands Technical Data Article number: CNMG160616‑RM5‑WSM20S‑WALTER Product type: Indexable turning insert Series / grade: Tiger‑tec Silver / WSM20S Shape: Rhombus 80° Chipbreaker: RM5 Edge radius: 1.6 Rake angle: 0° (negative) Plate size: 16 Thickness code: 06 Designation: CNMG160616‑RM5 ISO designation: CNMG160616‑RM5 WSM20S Manufacturer: Walter Tools Execution: G Tolerance class: M Material designation: S / M Numbers / Core technical data Edge radius: 1.6 mm Plate size: 16 Rake angle: 0° (negative) Thickness code: 06 Tolerance class: M Special features / Versions Coating: Tiger‑tec Silver Grade: WSM20S (coated cemented carbide) Suitable materials: stainless steels, heat‑resistant superalloys, titanium (depending on geometry) Chip control: RM5 chipbreaker Geometry: Rhombus 80° with 1.6 mm corner radius Series benefits: optimised chip formation and stable cutting edge FAQ What materials is this insert designed to machine? The CNMG160616‑RM5 WSM20S insert is developed for stainless steels and heat‑resistant superalloys (M and S material groups), providing edge stability under high thermal stress. How does the Tiger‑tec Silver coating improve performance? The Tiger‑tec Silver coating reduces thermal load at the cutting edge and enhances wear resistance, which contributes to longer tool life and more consistent machining results with the CNMG160616‑RM5 insert. Which chipbreaker should be expected and what does it offer? The insert features the RM5 chipbreaker, which is tuned for stable chip formation and reliable evacuation, reducing the risk of built‑up edge in demanding turning operations. Is the insert suitable for interrupted cuts or heavy roughing? Yes; the rhombus 80° geometry with negative rake 0° and a 1.6 mm corner radius provides a robust cutting edge appropriate for interrupted cuts and heavier material removal. Can this insert be used on titanium alloys? Depending on the specific geometry and machining strategy, the WSM20S grade can be applied to titanium and similar challenging materials, benefiting from the grade’s thermal stability. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160616-RM5 WSM30S WSM30S Wendeplatten - Walter Tools
High wear resistance from the Tiger·tec Silver coating combined with the RM5 chipbreaker ensures stable chip formation and extended edge life when machining stainless steel and heat‑resistant alloys; order the insert through Metav Werkzeuge or consult the team for application support. CNMG160616-RM5 WSM30S indexable turning insert for stainless steel — Walter Tools, Tiger·tec Silver A CNMG160616-RM5 WSM30S indexable turning insert designed for heavy‑duty applications, offering robust edge stability and reliable chip control for stainless steel and difficult‑to‑cut superalloys. Tiger·tec Silver coating for high wear resistance Optimised RM5 chipbreaker for stable chip control Rhombic 80° geometry with 1.6 mm corner radius Negative 0° rake for robust cutting edge Maximised process reliability for challenging materials The combination of the WSM30S carbide grade and Tiger·tec Silver coating delivers a cutting edge designed to withstand the thermal and mechanical demands of stainless steel and heat‑resistant superalloys. The coated hardmetal formulation improves heat resistance and reduces flank wear, resulting in longer tool life and fewer interruptions for index changes. For production environments where tool‑life consistency and reproducible results matter, this insert supports higher cutting speeds and stable performance under sustained loads. The technical focus on edge stability and wear control translates directly into reduced machining costs per component and improved throughput. Precise chip control and consistent surface quality The RM5 chipbreaker and the rhombic 80° shape with a 1.6 mm corner radius are engineered to generate controllable, segmented chips even in sticky or gummy stainless steel. The 0° (negative) rake angle increases edge strength and reduces the risk of built‑up edge formation, which helps maintain a predictable cutting action and consistent surface finish. These geometric choices support secure chip evacuation and minimise rework, making the insert suitable for both medium and heavy turning operations where process stability and component quality are priorities. Easy integration and predictable repeatability in production Tolerance class M, the standardised CNMG160616‑RM5 designation and the plate size 16 with thickness 06 ensure simple handling and compatibility with common clamping systems. The plate’s nominal geometry and proven sort assignment allow straightforward tool selection for stainless steel and similar alloys, simplifying inventory management. With the reliable performance of the WSM30S grade, tool planners gain predictable intervals for index changes and replacements, supporting leaner production planning and lower machine downtime. For tailored application advice or to secure suitable inserts for a specific stainless steel application, contact Metav Werkzeuge for guidance and order placement via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: CNMG160616‑RM5‑WSM30S‑WALTER Label: Drehwendeschneidplatte CNMG160616‑RM5 WSM30S Walter Tools Product type: Drehwendeschneidplatte / indexable turning insert Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WSM30S Designation: CNMG160616‑RM5 WSM30S Core data Plate form: Rhombus 80° Corner radius: 1.6 mm Plate size: 16 Plate thickness: 06 Rake angle: 0° (negative) Chipbreaker: RM5 Tolerance class: M Execution: G Special features Coating: Tiger·tec Silver (coated hardmetal) Material suitability: stainless steel, heat‑resistant superalloys and titanium (ISO groups M and S) Application focus: heavy‑duty and difficult‑to‑cut materials Intended benefit: stable chip formation and long tool life FAQ What materials is this insert suitable for? The CNMG160616‑RM5 WSM30S insert (Walter Tools Tiger·tec Silver) is specified for stainless steel and heat‑resistant superalloys/titanium, corresponding to ISO groups M and S. How does the RM5 chipbreaker affect machining? The RM5 chipbreaker on this turning insert promotes segmented chip formation and reliable evacuation, which supports consistent surface finish and reduces the likelihood of rework in stainless steel turning. What does the 0° (negative) rake angle mean for performance? A 0° (negative) rake angle increases edge robustness and reduces risk of built‑up edge, providing greater stability in heavy cuts and when machining tougher alloys with the CNMG160616-RM5 WSM30S. Is the CNMG160616‑RM5 compatible with standard toolholders? Yes, the CNMG160616‑RM5 designation and size 16 thickness 06 follow common insert standards and are compatible with holders designed for CNMG inserts. Which manufacturer grade is used and what are the benefits? The WSM30S grade from Walter Tools, within the Tiger·tec Silver family, offers enhanced heat resistance and wear protection, extending service life when machining stainless steel. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners and are mentioned solely for explanatory purposes. There is no affiliation between Metav Werkzeuge and the trademark holders. The offered item is original and new from the stated manufacturer.
CNMG160616-RP5 WKK20S WKK20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating and the WKK20S grade for reliable wear resistance and consistent chip control in cast‑iron turning; order the insert directly via Metav Werkzeuge or consult our specialists for application guidance. CNMG160616-RP5 WKK20S indexable turning insert for cast iron, Rhombic 80° — Walter Tools A CNMG160616-RP5 WKK20S indexable insert engineered for efficient machining of cast iron components, offering Tiger‑tec Silver coating and RP5 chip control for stable, productive turning. Tiger‑tec Silver coating for wear resistance Grade WKK20S tuned for cast iron Rhombic 80° form for stable cutting RP5 chipbreaker for controlled chips High productivity through tailored coating and grade The combination of the Tiger‑tec Silver coating and the WKK20S carbide grade delivers superior wear resistance specifically for abrasive cast‑iron applications. The coating reduces flank wear and thermal loading, which in turn stabilises cutting performance and extends tool life. For production environments that require consistent cycle times, this insert reduces the frequency of index changes and supports a smoother machining process. The RP5 chipbreaker is optimised to handle the typically short, brittle chips from cast iron, improving evacuation and reducing the risk of recutting while maintaining dimensional stability. Robust geometry for repeatable dimensional accuracy The rhombic 80° shape combined with a 1.6 mm corner radius and a 0° negative clearance provides a balance between edge strength and access to tight contours. The geometry supports reliable edge retention under interrupted cuts and helps maintain surface finish when moderately aggressive feeds are applied. With tolerance class M and execution G, the insert ensures predictable seating in toolholders and repeatable positioning, which is vital for batch production and multi‑station setups. The result is fewer regrinds, less scrap and improved process security. Application guidance and process integration Designed for the ISO group K (cast iron), this insert is suitable for a wide range of cast‑iron grades and turnover tasks that demand steady productivity. The series provides good chip control and long‑term stability, making it a practical choice for both single‑piece flow and volume turning. For integration into existing tool systems, match the CNMG seat and clamping to standard toolholders for rhombic inserts; fine‑tune feeds to favour chip formation with the RP5 breaker and adjust cutting speeds upwards within the limits of machine rigidity and coolant strategy to benefit from Tiger‑tec Silver's thermal protection. For specific cutting data and holder recommendations, consult the supplier for tailored parameters. For reliable cast‑iron turning with Walter Tools’ Tiger‑tec Silver technology, choose the CNMG160616‑RP5 WKK20S insert and contact Metav Werkzeuge for application support and order processing at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: CNMG160616-RP5-WKK20S-WALTER Designation: CNMG160616-RP5 WKK20S Brand: Walter Tools Series: Tiger‑tec Silver Facts Corner radius: 1.6 mm Plate size: 16 Thickness: 06 Free angle: 0° (negative) Plate form: Rhombus 80° Tolerance class: M Execution: G Special features Grade/coating: WKK20S, Tiger‑tec Silver (coated carbide) Chipbreaker: RP5 Material suitability: cast iron (ISO group K) Application focus: stable chip control, wear resistance FAQ Which materials is this insert designed for? The CNMG160616-RP5 WKK20S insert from Walter Tools is optimised for cast iron (ISO group K) and performs reliably on abrasive grey and nodular cast‑iron grades. What advantage does the Tiger‑tec Silver coating provide? Tiger‑tec Silver on the WKK20S grade improves heat resistance and reduces flank wear, enabling longer tool life and more consistent performance during cast‑iron turning. How does the RP5 chipbreaker affect machining? The RP5 chipbreaker promotes short, manageable chips in cast‑iron applications, enhancing evacuation and reducing the risk of chip entanglement when using the CNMG160616-RP5 WKK20S insert. What does the rhombic 80° form mean for cutting strategy? The rhombic 80° geometry offers a robust cutting edge and good approach angles for turning operations, supporting stable cuts and accessible tool paths for typical cast‑iron components. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered article is an original, factory‑new product of the manufacturer.
CNMG160616-RP5 WPP05G WPP05G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the RP5 chipbreaker for productive steel turning with consistent tool life; order the insert directly via Metav Werkzeuge or consult the team for application-specific selection. CNMG160616-RP5 WPP05G — Turning indexable insert, Tiger·tec Gold, for steel CNMG160616-RP5 WPP05G is a Tiger·tec Gold coated rhombic 80° indexable insert designed for productive turning of steel components, combining a reliable RP5 chipbreaker with a 1.6 mm corner radius. Tiger·tec Gold coating for long tool life RP5 chipbreaker for reliable chip control 80° rhombic form, 1.6 mm corner radius Designed for steel machining (ISO P) Higher productivity through advanced coating and substrate The combination of Tiger·tec Gold coating with a wear-resistant carbide substrate delivers measurable improvements in process reliability and tool life. The coated hardmetal grade WPP05G is tuned for steel machining and balances hardness and toughness to resist flank wear while maintaining edge strength. For production environments where predictable performance is essential, this cutting grade reduces unplanned tool changes and supports stable machining parameters, thus contributing to a smoother production flow and lower overall machining costs. Precise chip control and stable cutting geometry Equipped with the RP5 chipbreaker, the insert ensures controlled chip formation across a wide range of cutting conditions typical for ISO P materials. The 80° rhombic form and a 1.6 mm corner radius provide a robust cutting edge that tolerates interrupted cuts and moderate depths of cut, while the 0° (negative) rake contributes to edge strength under heavy loads. Together, these geometric features improve surface integrity and reduce the risk of built-up edge during continuous turning tasks. Application-specific suitability and material coverage This indexable plate is formulated primarily for steel applications (ISO P), making it suitable for unalloyed and alloyed steels where typical heat generation and chip behaviour are encountered. The WPP05G grade is characterised by a balanced performance profile—offering wear resistance for longer runs and sufficient toughness for tougher cutting conditions—so the insert is appropriate for both serial production and demanding single-part machining where quality and repeatability matter. Integration into tooling systems and handling advantages The insert designation and mounting geometry follow standard industry practice, allowing straightforward integration into compatible toolholders for turning operations. The CNMG160616-RP5 geometry simplifies tool inventory management while providing a versatile solution for a range of turning tasks. Handling and indexing are rapid, enabling quick replacement and minimising machine downtime—advantages that support lean production workflows and predictable throughput. Contact Metav Werkzeuge to specify the optimal Walter Tools Tiger·tec Gold turning insert for steel machining, quoting SKU CNMG160616-RP5-WPP05G-WALTER or request tailored application advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number/SKU: CNMG160616-RP5-WPP05G-WALTER Designation: CNMG160616-RP5 WPP05G Manufacturer: Walter Tools Product type: Turning indexable insert Facts Corner radius: 1.6 mm Insert form: Rhombus 80° Free/relief angle: 0° (negative) Thickness code: 06 Insert size: 16 Special features Grade/series: WPP05G — Tiger·tec Gold Chipbreaker: RP5 Tolerance class: M Material group suitability: ISO P (steel) Substrate/coating: coated carbide FAQ What materials is this insert suitable for? The CNMG160616-RP5 WPP05G insert is designed for ISO P materials and is optimised for turning a range of steels using the Tiger·tec Gold coated grade. How does the RP5 chipbreaker benefit turning operations? The RP5 chipbreaker provides reliable chip control during steel machining, improving process stability and reducing recutting of chips with the CNMG160616-RP5 WPP05G insert. Can the insert handle interrupted cuts? Yes, the 80° rhombic shape and 1.6 mm corner radius deliver a robust edge geometry that tolerates intermittent cutting conditions typical in turning operations. Is the coating suitable for high-volume production? The Tiger·tec Gold coating on the WPP05G grade is intended to enhance tool life and consistency, making the insert a sound choice for serial production of steel components. Which toolholders are compatible with the CNMG160616-RP5 geometry? Standard turning toolholders accepting CNMG-style plates will fit this geometry; the designation CNMG160616-RP5 indicates the established form and indexing interface. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned solely for descriptive purposes; there is no affiliation between Metav Werkzeuge and the trademark owners. The offered item is original and brand-new from the specified manufacturer.
CNMG160616-RP5 WPP10G WPP10G Wendeplatten - Walter Tools
Benefit from the combination of reliable edge life and secure chip control provided by the Tiger‑tec Gold grade; the CNMG160616‑RP5 WPP10G insert delivers consistent productivity with its 1.6 mm corner radius and RP5 chipbreaker — order via Metav Werkzeuge or consult our specialists for application support. CNMG160616-RP5 WPP10G turning insert (steel/P) — Tiger‑tec Gold, 1.6 mm radius — Walter Tools CNMG160616-RP5 WPP10G is a coated carbide turning insert designed for steel machining with a robust chipbreaker and stable geometry Tiger‑tec Gold coating for extended tool life WPP10G grade optimised for steel machining RP5 chipbreaker for reliable chip control 1.6 mm corner radius, rhombic 80° insert Longer tool life and consistent wear control for steel turning The Tiger‑tec Gold coating combined with the WPP10G grade supplies a balance of wear resistance and toughness tailored to steel (ISO P). This combination reduces flank and crater wear under typical turning conditions, which leads to longer intervals between tool changes and fewer unscheduled stoppages. For production environments this translates into predictable component quality and improved overall equipment effectiveness. The insert’s material and coating strategy are engineered for stable chip formation and controlled thermal response during machining. Stable geometry for improved surface finish and process reliability The 80° rhombic shape with a 1.6 mm corner radius and 0° negative rake ensures secure seat engagement and constant cutting performance across a range of feeds and depths. The geometry reduces tool deflection and supports consistent surface finish, especially during medium-depth profile turning. A clearly specified tolerance class M contributes to reproducible clamping and interchangeability in modular toolholders, which simplifies setup and helps maintain process stability across batches. Effective chip control that supports higher productivity Equipped with the RP5 chipbreaker, the insert promotes short, controllable chips when machining steels, improving evacuation and reducing the risk of entanglement or re-cutting. The coated carbide substrate helps sustain cutting edge integrity at elevated cutting speeds, enabling higher metal removal rates where the application permits. For workshop planners and shopfloor operators, this means fewer interruptions for chip management and a smoother machining cycle overall. Application guidance and selection criteria for reliable results This insert is specified for machining unalloyed and alloyed steels (ISO group P) and is suitable where a balance of wear resistance and toughness is required. When selecting cutting parameters, start from conservative speeds and feeds recommended for coated carbide in steel, then optimise based on component hardness and setup stiffness. The combination of the Tiger‑tec Gold coating and RP5 breaker is particularly suitable for stable turning operations and repeatable batch work; for tailored cutting-data sheets or material-specific recommendations, Metav Werkzeuge can provide application advice and documented starting values. Contact Metav Werkzeuge for tailored cutting data and to source the Walter Tools CNMG160616‑RP5 WPP10G insert with Tiger‑tec Gold coating Technical Data Article number: CNMG160616-RP5-WPP10G-WALTER Designation: CNMG160616-RP5 WPP10G Manufacturer: Walter Tools Product type: Turning insert Facts Insert size: 16 Corner radius: 1.6 mm Relief angle: 0° (negative) Shape: Rhombus 80° Chipbreaker: RP5 Grade: WPP10G Series: Tiger‑tec Gold Tolerance class: M Thickness code: 06 Special features Coating technology: Tiger‑tec Gold Suitable for: Steel (ISO P) Coated carbide insert Robust chip control with RP5 Stable edge geometry for consistent surface finish FAQ What materials is this insert intended for? The CNMG160616‑RP5 WPP10G insert is intended primarily for steel machining (ISO group P) and the WPP10G grade is optimised for that application. How does the Tiger‑tec Gold coating improve performance? Tiger‑tec Gold supplies enhanced wear resistance and thermal stability on the CNMG160616‑RP5 WPP10G, extending tool life and maintaining cutting-edge integrity at higher speeds. What is the effect of the 1.6 mm corner radius on machining? A 1.6 mm corner radius increases edge strength and delivers a more robust cut, improving surface finish and reducing the risk of chipping under interrupted or heavier cuts. When should the RP5 chipbreaker be preferred? The RP5 chipbreaker is recommended for operations where predictable, short chips aid evacuation and reduce risk of chip re-cutting—typical in continuous turning of steels. Can this insert be used for interrupted cuts? Yes; the combination of the WPP10G grade and the 1.6 mm radius provides toughness suitable for light to moderate interrupted turning in steel, with attention to cutting data and clamping rigidity. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen The Walter AG (brand appearance: Walter Tools) is part of a global group known for precision machining solutions. Protected trademarks and product names are the property of their respective owners and are mentioned here for explanatory purposes only. The offered item is an original, factory‑new product from the manufacturer.
CNMG160616-RP5 WPP20G G Wendeplatten - Walter Tools
Combining the Tiger·tec Gold coating with the RP5 chipbreaker and a robust 1.6 mm corner radius delivers extended tool life and consistent chip control for turning steel; order the CNMG160616-RP5 WPP20G indexable turning insert directly via Metav Werkzeuge or contact our consultants for application advice. CNMG160616-RP5 WPP20G indexable turning insert – Tiger·tec Gold for steel | Walter Tools A CNMG160616-RP5 WPP20G indexable turning insert engineered for reliable, productive machining of steel in general turning operations. Tiger·tec Gold coated for high tool life RP5 chipbreaker for controlled chip formation Rhombic 80° geometry for versatile turning 1.6 mm corner radius for robust edge strength Efficient machining through optimised coating and substrate The combination of the Tiger·tec Gold coating and a coated carbide substrate ensures improved resistance to abrasion and thermal loading during continuous turning of steel. The coating technology, developed for a wide material spectrum, reduces wear mechanisms that commonly limit tool life. As a result, cutting edge durability is increased, which leads to fewer insert changes and longer uninterrupted cycles—benefits that translate into measurable productivity gains on batch and single-piece production. Reliable chip control and predictable cutting behaviour Equipped with the RP5 chipbreaker, this insert produces controlled, short chips in a variety of cutting conditions, improving process security and surface quality. The chipformer design, paired with the rhombic 80° geometry, stabilises cutting forces and enables consistent results when roughing and finishing steel components. For users less familiar with chip geometry, the RP5 designation identifies a general-purpose breaker suited for the typical heat and chip characteristics of steel turning. Robust edge design for demanding operations The 1.6 mm corner radius enhances edge strength, reducing the risk of chipping in interrupted cuts or when machining harder sections. This feature is particularly useful when machining parts with variable cross-sections or when transitioning from roughing to semi-finishing passes. The negative 0° rake configuration contributes to a secure cutting edge, favouring stability and repeatable performance in medium to heavy-duty turning. Practical selection and application guidance The CNMG160616-RP5 WPP20G insert is targeted at general steel applications (ISO group P) and is suited to both conventional and CNC lathes, offering a straightforward choice for workshops seeking predictable performance. Insert indexing is simple and repeatable, and the geometry supports a balance between material removal rate and surface finish quality. If additional cutting data or feed and speed recommendations are required, Metav Werkzeuge provides application support and can advise on optimised parameters for specific steels and machine setups. Contact Metav Werkzeuge for tailored cutting data or application support for the Walter Tools CNMG160616-RP5 WPP20G indexable turning insert Technical data Article number: CNMG160616-RP5-WPP20G-WALTER SKU: CNMG160616-RP5-WPP20G-WALTER Product type: indexable turning insert Series: Tiger·tec Gold Facts Insert shape: rhombic 80° Corner radius: 1.6 mm Thickness: 06 Free cutting angle: 0° (negative) Chipbreaker: RP5 Grade/sort: WPP20G Tolerance class: M Size: 16 Special features Coating: Tiger·tec Gold (coated carbide) Material application: steel (ISO P) Edge geometry: negative rake for stability Application focus: versatile turning, general-purpose steel machining FAQ What materials is this insert suitable for? The CNMG160616-RP5 WPP20G indexable turning insert (Walter Tools) is designed primarily for steel (ISO group P) and is optimised for the heat and chip behaviour typical of unalloyed and alloyed steels. How does the RP5 chipbreaker affect machining? The RP5 chipbreaker on this Walter Tools insert provides controlled, short chips and stable cutting forces, improving process reliability and surface finish during turning operations. Can the insert be used for finishing as well as roughing? Yes, the rhombic 80° geometry combined with the 1.6 mm corner radius makes the insert suitable for both roughing and semi-finishing passes, offering a compromise between material removal rate and surface quality. Is the coating suitable for higher cutting speeds? The Tiger·tec Gold coating on the WPP20G grade enhances thermal and wear resistance, supporting higher cutting speeds within recommended parameters for steel machining. How is repeatability ensured when indexing the insert? The CNMG form factor and the tolerance class M ensure precise seating and repeatable positioning after indexing, contributing to consistent dimensional and surface results. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
CNMG160616-RP5 WPP30G Wendeplatten - Walter Tools
High process reliability and efficient chip control result from the Tiger·tec Gold coating and the RP5 chipbreaker, delivering consistent performance when machining steel; the negative 0° geometry and 1.6 mm corner radius add edge strength for secure turning operations. Order the CNMG160616-RP5 WPP30G directly via Metav Werkzeuge or consult our advisors for tailored application support. CNMG160616-RP5 WPP30G turning insert — Tiger·tec Gold for steel, Walter Tools The CNMG160616-RP5 WPP30G is a rhombic 80° turning insert designed for productive steel machining, combining a robust negative geometry with a Tiger·tec Gold coated carbide grade for improved wear resistance. Tiger·tec Gold coating for extended tool life RP5 chipbreaker for stable chip formation Rhombic 80° shape for versatile turning 1.6 mm corner radius for robust edge strength Increase machining uptime with Tiger·tec Gold technology The coated carbide grade WPP30G, part of the Tiger·tec Gold series, is developed for reliable performance in steel machining (ISO group P). The multilayer coating improves heat resistance and wear behaviour under the thermal loads typical of turning operations, which translates into longer edge life and fewer insert changes. By favouring stable chip formation and abrasion resistance, the coating supports sustained cutting parameters and reduces process variability, making the insert a rational choice for shops aiming to raise throughput while maintaining consistent surface quality. Robust geometry for secure cutting and predictable results The insert’s rhombic 80° shape and 0° (negative) free angle create a geometry that resists deformation under moderate cutting forces, while the 1.6 mm corner radius balances edge strength and form accuracy. The integrated RP5 chipbreaker is tuned for the steel machining range, promoting short, controllable chips and stable cutting conditions. The tolerance class M and the design code for thickness 06 reflect manufacturing precision and repeatability, supporting predictable tool life and dimensional consistency in serial production. Practical benefits for workshop workflows and process setup Designed for versatile turning tasks, this insert excels in general steel applications and is optimised for reliable chip control and good surface finish at common cutting speeds. The grade’s toughness rating supports operations where a balance between wear resistance and resilience is required, helping to avoid premature chipping. For process planning, select appropriate cutting data calibrated to the material and machining strategy; technical advisors at Metav Werkzeuge can assist with parameter tables and holder selection to ensure the insert is used within its intended operating window. Discuss specific application requirements with Metav Werkzeuge to exploit the durability and productivity benefits of the Walter Tools CNMG160616-RP5 WPP30G Tiger·tec Gold turning insert Technical data Article number: CNMG160616-RP5-WPP30G-WALTER Label: Drehwendeschneidplatte CNMG160616-RP5 WPP30G Walter Tools Product type: Turning insert Brand: Walter Tools ISO designation: CNMG160616-RP5 WPP30G Series: Tiger·tec Gold Grade: WPP30G Core figures Corner radius: 1.6 mm Plate size: 16 Thickness code: 06 Free angle: 0° (negative) Tolerance class: M Features & suitability Chipbreaker: RP5 Shape: Rhombus 80° Coating technology: Tiger·tec Gold Substrate: coated carbide Application: machining steel (ISO P) FAQ Is this insert suitable for stainless steel (austenitic grades)? This insert is specified for steel (ISO P); machining stainless steel is not defined in the provided data for the CNMG160616-RP5 WPP30G and may require a different grade or adjusted cutting data. What are the advantages of the Tiger·tec Gold coating? The Tiger·tec Gold coating on the CNMG160616-RP5 WPP30G improves heat resistance and wear performance, extending usable edge life and stabilising the cutting process when machining steels. Which chipbreaker is fitted and what is its effect? The RP5 chipbreaker on this turning insert promotes controlled, short chips appropriate for steel machining, supporting safer chip evacuation and consistent surface finish. Can this insert be used in conventional toolholders for CNMG geometry? Yes; the CNMG form follows standard insert geometry and can be mounted in compatible holders designed for CNMG inserts, taking into account the negative geometry and required clamping. How does the 1.6 mm corner radius influence part finish? A 1.6 mm corner radius offers a compromise between edge strength and surface generation—providing robustness against chipping while maintaining good form accuracy on turned profiles. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160616-RP7 WKP30S Wendeplatten - Walter Tools
Benefit from the durable Tiger·tec Silver coating and the RP7 chipbreaker for stable chip control and long wear life; the rhombic 80° geometry with a 1.6 mm corner radius and 0° negative rake delivers predictable performance in Stahl and Gusseisen turning. Order the CNMG160616-RP7 WKP30S directly via Metav Werkzeuge or consult our advisors for application support. CNMG160616-RP7 WKP30S — Indexable turning insert, Rhombic 80°, 1.6 mm radius | Walter Tools The CNMG160616-RP7 WKP30S is an indexable turning insert designed for precision turning applications in unalloyed and alloyed Stahl and Gusseisen, combining a coated carbide grade with a dedicated chipbreaking geometry. Tiger·tec Silver coated carbide RP7 chipbreaker for controlled chips Rhombic 80° form, 1.6 mm corner radius 0° negative rake for stable cutting Stable chip control and longer tool life for demanding turning The combination of the Tiger·tec Silver coating and the WKP30S grade provides enhanced wear resistance and thermal stability, making the insert well suited to continuous production. The integrated RP7 chipbreaker promotes predictable chip formation, which reduces downtime caused by irregular chips and supports unattended turning cycles. For operations where consistent surface quality and tool life matter, this insert offers a balance of durability and machining reliability that helps maintain steady cycle times. Geometry engineered for repeatable accuracy and secure seating The rhombic 80° form and the 1.6 mm corner radius deliver a versatile cutting geometry that supports both roughing and finishing passes with controlled cutting forces. The 0° (negative) free angle increases edge strength and enhances stability in interrupted cuts or heavy engagement, while the M tolerance class ensures repeatable seating and interchangeability in toolholders. This geometry reduces the risk of edge chipping and helps maintain dimensional consistency across workpieces. Application guidance and process benefits for Stahl and Gusseisen Designed according to ISO material group guidance, the insert targets machining of P (Stahl) and K (Gusseisen) materials: the grade adapts to the thermal and abrasive conditions typical of these groups. In practical terms, this means improved performance on unalloyed and alloyed steels as well as various cast irons. The coated carbide substrate supports higher sustained cutting rates and contributes to lower tooling costs per component through extended tool life and dependable performance. Productive integration into established turning processes The insert’s standardised dimensions and grade make it straightforward to integrate into existing tooling systems. The robust grade and coating strategy help reduce the frequency of tool changes and support consistent surface finishes across batch production. Combined with a suitable cutting data sheet and toolholder selection, the insert can contribute to measurable process stability and predictable maintenance intervals. For high-demand turning tasks where chip control and edge security are critical, contact Metav Werkzeuge for tailored advice on integrating the CNMG160616-RP7 WKP30S into production or arrange procurement via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: CNMG160616-RP7-WKP30S-WALTER Designation: CNMG160616-RP7 WKP30S Series: Tiger·tec Silver Manufacturer: Walter Tools Facts Corner radius: 1.6 mm Insert size: 16 mm Thickness: 06 Free angle: 0° (negative) Tolerance class: M Special features Coating: Tiger·tec Silver Grade: WKP30S (coated carbide) Chipbreaker: RP7 Geometry: Rhombic 80° Application: Stahl and Gusseisen Material guidance: P / K Execution: G FAQ What materials is this insert suitable for? The CNMG160616-RP7 WKP30S is configured for machining P (Stahl) and K (Gusseisen) material groups, offering wear resistance and chip control appropriate for steels and cast irons. How does the RP7 chipbreaker influence machining? The RP7 chipbreaker promotes controlled, short chips and improves evacuation in turning, which helps maintain steady cycle times and reduces manual chip handling. What advantages does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating increases thermal stability and wear resistance, enabling longer tool life under continuous or demanding cutting conditions. Is the insert suitable for interrupted cuts or heavy engagement? Yes; the 0° negative free angle and the robust grade improve edge strength and stability in interrupted cuts and heavier material removal. Which insert geometry is this and what does it mean for toolholders? The rhombic 80° form is a common indexable geometry that fits standard toolholders designed for CNMG-style inserts, supporting straightforward replacement and repeatable seating. Hersteller: Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered item is original, factory-new goods of the manufacturer Walter Tools.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com