DCMT070202-FW4 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the FW4 chipbreaker for longer tool life and stable chip control in steel turning; order the insert directly via Metav Werkzeuge or contact their consultants for application advice. DCMT070202-FW4 WPP20G turning insert by Walter Tools — Tiger·tec Gold, for steel (ISO P) DCMT070202-FW4 WPP20G is a rhombic 55° indexable turning insert designed for reliable, high-throughput steel machining and consistent edge performance Tiger·tec Gold coated carbide for wear resistance Compatible with steel (ISO P) machining 0.2 mm corner radius for accurate surface finish FW4 chipbreaker for controlled chip formation Increased uptime through a wear‑resistant coating The Tiger·tec Gold coating on the grade WPP20G provides a balanced combination of wear resistance and toughness that reduces the frequency of tool changes in continuous production. Thanks to the multilayer coating technology, heat resistance is improved and flank wear is delayed, which supports longer uninterrupted machining cycles. This leads to a more efficient production flow and predictable tool‑life planning on the shop floor. Reliable chip control and improved surface quality The rhombic 55° geometry together with the FW4 chipbreaker delivers stable chip formation when cutting steel (ISO P), lowering the risk of built‑up edge and improving surface finish. The small 0.2 mm corner radius helps achieve precise dimensional control and a fine machined surface on profiles and turning paths where a defined edge is required. Controlled chip evacuation reduces thermal load at the cutting zone, contributing to repeatable part quality and fewer rework operations. Consistent performance across common steel applications Designed as a universal turning grade for steel, the insert is suited to a broad range of standard and alloyed steels, offering a dependable compromise between toughness and wear resistance. The geometry and clearance angle support secure seating in standard tool holders, enabling quick insert changes and straightforward process integration. For shop environments seeking reliable, routine performance from a well‑engineered grade, the DCMT070202-FW4 WPP20G insert from Walter Tools provides a predictable production solution For dependable steel turning performance with Tiger·tec Gold technology, request technical support or place an order through Metav Werkzeuge — info@metav-werkzeuge.com • +49 2822 7131930 Technical data SKU: DCMT070202-FW4-WPP20G-WALTER Designation: DCMT070202-FW4 WPP20G Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.2 mm Plate form: Rhombus 55° Plate size: 07 Plate thickness: 02 Special features Series: Tiger·tec Gold Grade: WPP20G (coated carbide) Chipbreaker: FW4 Tolerance class: M Application: Steel (ISO P) FAQ Is this insert suitable for a wide range of steel turning operations? Yes. The DCMT070202-FW4 WPP20G insert from Walter Tools is designed for general steel machining (ISO P), offering a balance of wear resistance and toughness for common turning tasks. Which chip behaviour can be expected with the FW4 chipbreaker? The FW4 chipbreaker on this insert promotes controlled chip segmentation and evacuation when machining steel, which reduces heat concentration and improves surface consistency. How does the Tiger·tec Gold coating affect tool life? The Tiger·tec Gold coating on the WPP20G grade enhances thermal stability and wear resistance, extending the usable life of the insert under typical steel cutting conditions. Can the insert be used in standard turning tool holders? Yes. The rhombic 55° form and standard dimensions allow the insert to be mounted in common indexable turning tool holders compatible with this geometry and size. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT070202-FW4 WSM20S WSM20S Wendeplatten - Walter Tools
The combination of a Tiger·tec Silver cutting grade, a precise 0.2 mm corner radius and an FW4 chipbreaker delivers reliable chip control and extended tool life for demanding stainless and heat‑resistant alloy applications; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. DCMT070202-FW4 WSM20S indexable turning insert — Tiger·tec Silver, for stainless steels (Walter Tools) The DCMT070202-FW4 WSM20S is an indexable turning insert engineered for machining stainless steels and heat‑resistant superalloys, combining a rhombic 55° geometry with a 7° clearance and a 0.2 mm corner radius for stable cutting and consistent surface finish Tiger·tec Silver coated grade WSM20S Optimised FW4 chipbreaker for stable chips Rhombic 55° shape with 0.2 mm corner radius Suited to stainless steels and superalloys Consistent process security for difficult‑to‑cut materials The coated cemented‑carbide grade WSM20S of the Tiger·tec Silver series is developed for high thermal and mechanical loads common when machining stainless steels and heat‑resistant alloys. The combination of coating technology and substrate enhances wear resistance and maintains a stable cutting edge, which reduces the frequency of index changes and helps achieve reproducible production results. This results in improved machine utilisation and predictable tool life when cutting demanding materials. Improved chip control and surface quality with FW4 geometry The FW4 chipbreaker and the rhombic 55° form provide controlled chip formation and evacuation in interrupted and continuous cuts. A defined 0.2 mm corner radius reduces edge chipping while supporting finish requirements; the modest 7° clearance angle minimises rubbing and contributes to a finer surface. For shops aiming to balance material removal and workpiece quality, the geometry yields tangible benefits in machining stability and part finish. Versatile application and handling advantages in production The insert’s designation and geometry support a wide range of turning tasks on materials classified in ISO groups M and S (rostfreie Stähle and heat‑resistant superalloys/titanium). The insert’s compact design and standardised interface simplify toolholder selection and change‑over. When paired with appropriate cutting data, this indexable solution enhances productivity through longer cutting intervals and reduced unplanned downtime, while offering straightforward handling and stock management for production planners. Choose the Walter Tools Tiger·tec Silver grade for demanding stainless and superalloy turning operations and contact Metav Werkzeuge for bespoke recommendations and order options. Technical data SKU: DCMT070202-FW4-WSM20S-WALTER Article: Drehwendeschneidplatte DCMT070202-FW4 WSM20S Walter Tools Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WSM20S Core specifications Free angle: 7° Corner radius: 0.2 mm Plate shape: Rhombus 55° Plate size: 07 Plate thickness: 02 Tolerance class: M Special features Chipbreaker: FW4 Coating technology: Tiger·tec Silver Substrate: coated cemented carbide Material suitability: stainless steels (ISO M), heat‑resistant superalloys/titanium (ISO S) FAQ What materials is this insert best suited for? The DCMT070202-FW4 WSM20S (Walter Tools) is optimised for stainless steels and heat‑resistant superalloys/titanium, reflecting the WSM20S grade characteristics. How does the FW4 chipbreaker affect machining? The FW4 chipbreaker promotes controlled chip formation and evacuation, improving process stability and reducing the risk of built‑up edge during turning operations on tough materials. What benefits does the Tiger·tec Silver technology provide? Tiger·tec Silver offers a coated carbide solution that improves wear resistance and cutting‑edge stability, which extends cutting intervals and supports consistent surface quality. Is the 0.2 mm corner radius suitable for finishing? A 0.2 mm corner radius provides a balance between strength and finish capability, reducing edge chipping while supporting acceptable surface quality in semi‑finishing and finishing passes. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Protected brand names and trademarks are the property of their respective owners. Brand names and trademarks are mentioned only for explanatory purposes; there is no affiliation between our company and the referenced brands. The offered item is an original, factory‑new product of the manufacturer.
DCMT070204-FK6 WKK10S WKK10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating and the WKK10S grade for abrasion resistance and predictable wear, plus the FK6 chipbreaker that improves chip control during cast iron turning; order supply and technical consultation via Metav Werkzeuge when required. DCMT070204-FK6 WKK10S indexable turning insert (for cast iron) — Walter Tools, Tiger‑tec Silver, 7° clearance The DCMT070204-FK6 WKK10S is an indexable turning insert engineered for reliable cast iron machining, offering a coated‑carbide grade in the Tiger‑tec Silver series with FK6 chip control. Tiger‑tec Silver coating for abrasion resistance Optimised for cast iron (ISO K) machining Rhombic 55° geometry, 7° clearance angle 0.4 mm corner radius for consistent finishes Increased productivity through a wear‑resistant grade and predictable edge life The combination of the WKK10S coated‑carbide grade and the Tiger‑tec Silver technology delivers a high level of abrasion resistance specifically tailored to abrasive cast iron alloys. This results in stable cutting-edge behaviour and fewer unexpected tool changes, which supports continuous production. The coated microstructure reduces flank wear under typical interrupted cuts associated with grey and spheroidal graphite cast iron, so machining cycles become more predictable and planning of tool change intervals is simplified. Geometry designed for repeatable finishes and tool stability A Rhombic 55° seat paired with a 7° clearance angle provides a balanced engagement between insert and workpiece, reducing cutting forces and improving nest fit in standard toolholders. The 0.4 mm corner radius supports a consistent surface condition while maintaining robust edge strength for finishing passes; the tolerance class M ensures dimensional conformity across batches. These geometric choices translate into fewer rejects, more consistent surface quality and straightforward integration into existing insert‑based turning systems. Efficient chip control and straightforward implementation in production The FK6 chipbreaker is optimised for the typically short, brittle chips produced from cast iron, promoting secure evacuation and minimising recutting. This improves process stability on both single‑piece and serial turning operations. Compatibility with common indexable‑insert toolholders means installation is immediate, and the insert’s characteristics contribute to lower overall tooling costs through extended useful life and reduced downtime. If there is uncertainty about suitability for a specific application, the Metav Werkzeuge technical team can be contacted for data‑driven advice: info@metav-werkzeuge.com or +49 2822 7131930. Contact Metav Werkzeuge for an application review and to secure supply of the Walter Tools DCMT070204-FK6 WKK10S insert with Tiger‑tec Silver technology. Technical data SKU: DCMT070204-FK6-WKK10S-WALTER Designation: DCMT070204-FK6 WKK10S Product type: Indexable turning insert Brand: Walter Tools Facts Geometry: Rhombic 55° Clearance angle: 7° Corner radius: 0.4 mm Insert size: 07 Thickness: 2.0 mm Tolerance class: M Special features Coating: Tiger‑tec Silver Grade: WKK10S (coated carbide) Chipbreaker: FK6 Application: Cast iron (ISO K) Series: Tiger‑tec Silver FAQ What materials is this insert designed for? The DCMT070204-FK6 WKK10S insert is optimised for cast iron (ISO K) applications and the WKK10S grade is tuned for abrasive wear resistance in those materials. How does the FK6 chipbreaker affect machining? The FK6 chipbreaker on this Walter Tools insert promotes short, controlled chips typical of cast iron, improving chip evacuation and reducing the risk of recutting. Which toolholders are compatible with the insert geometry? Standard toolholders accepting a Rhombic 55° DCMT insert will accommodate the DCMT070204-FK6 WKK10S; the geometry and tolerance class M ensure reliable seating in common pockets. What performance benefit does Tiger‑tec Silver provide? The Tiger‑tec Silver coating enhances abrasion resistance and lengthens effective tool life on abrasive cast iron grades, providing more consistent edge stability across production runs. Is technical advice available for application optimisation? Yes, Metav Werkzeuge can advise on cutting data and tool‑holder pairing for the DCMT070204-FK6 WKK10S to ensure optimal process reliability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between Metav Werkzeuge and the listed brands. The product offered is original and factory‑new.
DCMT070204-FK6 WKK20S WKK20S Wendeplatten - Walter Tools
Achieve dependable cast-iron turning through the combination of Tiger‑tec Silver wear resistance and precise 7° clearance geometry; Order the DCMT070204-FK6 WKK20S directly via Metav Werkzeuge or ask our consultants if needed DCMT070204-FK6 DCMT070204-FK6 WKK20S – Turning insert for cast iron (Tiger‑tec Silver) | Walter Tools The DCMT070204-FK6 WKK20S is a rhombic 55° turning insert designed for robust, repeatable machining of cast iron components with a coated carbide grade optimised for abrasive materials Tiger‑tec Silver coating for high wear resistance Optimised for cast iron (ISO group K) Rhombic 55° insert with 0.4 mm corner radius FK6 chipbreaker for reliable chip control High-performance grade for abrasive cast-iron machining The Tiger‑tec Silver WKK20S grade provides a coated carbide formulation that balances wear resistance and toughness for abrasive cast-iron applications. This combination reduces flank wear and extends tool life, which directly lowers tool-change frequency and supports uninterrupted production runs. The engineered coating chemistry helps maintain a stable cutting edge under the short, breaking chip behaviour typical of cast iron, delivering consistent results in batch and series production. Precision geometry for consistent surface quality The rhombic 55° shape with a 7° clearance angle and 0.4 mm corner radius ensures predictable cutting forces and a repeatable edge line. The geometrical setup contributes to a controllable cutting zone and a reliable surface finish, while the tolerance class M supports interchangeability in tooling systems. These properties make the insert suitable where dimensional reproducibility and a steady process window are required, reducing the need for frequent adjustment and inspection. Effective chip control and process stability Equipped with the FK6 chipbreaker, the insert promotes short, manageable chips and prevents entanglement in the tool zone. Improved chip formation reduces downtime for chip clearing and decreases the risk of surface damage on the workpiece. The chip control characteristic is particularly valuable when machining discontinuous or porous castings, where uncontrolled chips can otherwise compromise cycle time and part quality. Practical application and shop-floor benefits Designed for ISO group K materials, this turning insert fits a wide range of cast-iron turning tasks from roughing to finishing when balanced feeds and speeds are applied. The coated grade and chipbreaker together enhance productivity and process reliability, making the insert an effective choice for component manufacturers seeking stable operation and longer tool life. For specific machining parameters and recommended feeds, consult Metav Werkzeuge for tailored guidance. Contact Metav Werkzeuge to discuss specification, availability and suitable cutting parameters for Walter Tools Tiger‑tec Silver turning inserts; eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: DCMT070204-FK6-WKK20S-WALTER Designation: DCMT070204-FK6 WKK20S Manufacturer: Walter Tools Facts Free angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 55° Plate size: 07 Plate thickness: 02 Tolerance class: M Special features Series: Tiger‑tec Silver Grade: WKK20S (coated carbide) Chipbreaker: FK6 Suitable for: cast iron (ISO group K) Execution: T FAQ What materials is this insert designed for? The DCMT070204-FK6 WKK20S is designed primarily for machining cast iron (ISO group K) and its coated carbide grade is tuned for abrasive cast materials. How does the FK6 chipbreaker affect machining? The FK6 chipbreaker creates short, controllable chips, improving process stability and minimising interruptions during cast-iron turning. What are the key geometry values to consider for setup? Important values include the rhombic 55° shape, a 7° free angle and a 0.4 mm corner radius, which together influence cutting forces and surface finish. Is this insert suitable for finishing as well as roughing? Yes; with appropriately adjusted feeds and speeds the coated WKK20S grade and the insert geometry allow both productive roughing and consistent finishing operations. Where can recommended cutting data be obtained? Cutting data and application advice are available from Metav Werkzeuge; the Walter Tools grade information can guide initial parameter selection. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT070204-FM4 WMP20G T Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, FM4 chip control and a 0.4 mm corner radius for dependable performance in rostfreier Stahl turning; order via Metav Werkzeuge or ask our consultants for cutting-data recommendations. DCMT070204-FM4 WMP20G turning insert (rostfreier Stahl) – Walter Tools, Tiger·tec Gold, 7° The DCMT070204-FM4 WMP20G is a rhombic 55° turning insert engineered for medium to robust rostfreier Stahl machining, offering stable chip formation and extended tool life. Tiger·tec Gold coating for long tool life Optimised FM4 chipbreaker for stable chips Rhombic 55° form, 0.4 mm corner radius 7° clearance angle for secure cutting Increased productivity through advanced coating and grade The combination of the Tiger·tec Gold coating with the WMP20G grade delivers a high level of thermal and mechanical resistance that is especially valuable when machining rostfreier Stahl. The coating stabilises the cutting edge, reducing the risk of edge chipping and built-up edge under challenging conditions. This results in more consistent tool life and fewer tool changes, which directly supports improved process reliability and shorter non-productive times on the shop floor. Precision geometry for consistent surface quality and chip control The rhombic 55° insert geometry, paired with the FM4 chipbreaker, promotes predictable chip formation and efficient evacuation in medium to heavier cuts. The 0.4 mm corner radius contributes to robust edge strength while maintaining a good surface finish on the workpiece. The 7° clearance angle reduces rubbing at the flank face and helps to preserve the cutting edge, enabling steady dimensional accuracy and repeatable results in serial production and one-off jobs alike. Application scope, handling and economic advantages Designed primarily for rostfreier Stahl, this coated carbide insert is suited to a broad range of parts-production tasks where thermal stability and secure chip control are required. The combination of a modern coating system and a proven chipbreaker reduces rework and improves process uptime, which can lower per-part manufacturing costs. As a Walter Tools product from the Tiger·tec Gold family, it supports reliable performance under medium to robust cutting conditions and integrates with standard holders for quick tooling set-up. Contact Metav Werkzeuge for tailored cutting data, availability and delivery options for Walter Tools DCMT070204-FM4 WMP20G inserts Technical Data SKU: DCMT070204-FM4-WMP20G-WALTER Designation: DCMT070204-FM4 WMP20G Manufacturer: Walter Tools Series: Tiger·tec Gold Core data Clearance angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 55° Plate size: 07 Thickness: 02 Tolerance class: M Special features Chipbreaker: FM4 Grade/Coating: WMP20G (coated carbide) Application: rostfreier Stahl Execution: T FAQ What materials is this insert intended for? The DCMT070204-FM4 WMP20G insert is specified for machining rostfreier Stahl and is optimised for the typical demands of stainless-steel turning. How does the FM4 chipbreaker affect performance? The FM4 chipbreaker promotes controllable chip formation and smooth evacuation, improving surface finish and reducing the risk of entangling chips during rostfreier Stahl machining. What is the benefit of the Tiger·tec Gold coating? The Tiger·tec Gold coating increases thermal and mechanical resistance, extending tool life and stabilising the cutting edge under medium to robust cutting conditions. Is the 0.4 mm corner radius suitable for general turning operations? A 0.4 mm corner radius provides a compromise between edge strength and surface quality, making it suitable for many turning applications where robust performance is required. Can this insert be used in standard toolholders? The insert form and dimensions follow common industry standards for rhombic 55° turning inserts and are compatible with corresponding toolholder systems. Manufacturer/Responsible: Walter Tools; Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is an original factory-new product of the manufacturer.
DCMT070204-FM4 WMP20S WMP20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the FM4 chipbreaker to achieve stable cutting on rostfreier Stahl and prolonged tool life; order directly via Metav Werkzeuge or consult the technical team for application matching. DCMT070204-FM4 WMP20S Drehwendeschneidplatte by Walter Tools — Rhombic 55°, 7° relief A DCMT070204-FM4 WMP20S indexable turning insert designed for precision turning of rostfreier Stahl under medium to robust cutting conditions Tiger·tec Silver coating for longer tool life WMP20S grade optimised for rostfreier Stahl FM4 chipbreaker for secure chip control Rhombic 55° geometry for versatile turning Stable machining performance for rostfreier Stahl The coated carbide combination of Tiger·tec Silver and grade WMP20S is tailored to the challenges of machining rostfreier Stahl, where toughness and build‑up tend to compromise edge stability. The rhombic 55° geometry and the fine corner radius 0.4 deliver a controlled engagement and predictable tool behaviour, reducing the risk of unexpected edge damage. This results in consistent cutting forces and improved process reliability during both semi‑finishing and finishing operations. Consistent chip control and surface quality Equipped with the FM4 chipbreaker, this insert promotes secure chip formation and evacuation even under the higher heat and stickiness typical of rostfreier Stahl. The relief angle 7° helps to reduce rubbing while maintaining a stable cutting edge. Together these features support a superior surface finish and minimise rework cycles, helping production lines to keep tolerances tight and save time on downstream operations. Practical benefits for production workflows The compact Rhombic 55° insert shape provides flexibility across a range of turning tasks, enabling quick adaptation between contouring and plunge cuts. The coated, indexable design allows rapid insert changes and predictable tool life, which simplifies inventory planning and reduces machine downtime. Where repeatability and process security are priorities, the insert’s engineering supports steady, reproducible results that favour cost‑efficient production. Contact Metav Werkzeuge for application support and tailored recommendations on Walter Tools Tiger·tec Silver inserts; technical consultants are available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: DCMT070204-FM4-WMP20S-WALTER Product designation: DCMT070204-FM4 WMP20S Manufacturer: Walter Tools Product type: Drehwendeschneidplatte Core data Geometry: Rhombus 55° Relief angle: 7° Corner radius: 0,4 Size code: 07 Thickness code: 02 Tolerance class: M Special features Coating/grade: Tiger·tec Silver / WMP20S Chipbreaker: FM4 Execution: T Suitable for: rostfreier Stahl Substrate: coated carbide Series: Tiger-tec Silver ISO designation: DCMT070204-FM4 WMP20S FAQ What materials is this insert suitable for? The insert is specified for machining rostfreier Stahl and is optimised for medium to robust cutting conditions in this material group. Which chipbreaker does the insert use and what is the benefit? The FM4 chipbreaker ensures controlled chip formation and reliable evacuation when turning rostfreier Stahl, improving surface quality and process stability. How does the Tiger·tec Silver coating help in production? Tiger·tec Silver increases resistance to wear and supports a stable cutting edge under the thermal and mechanical stresses associated with rostfreier Stahl machining. Is the insert compatible with standard toolholders for DCMT geometry? Yes, the insert follows the DCMT geometry and fits standard toolholders designed for rhombic 55° turning inserts with the corresponding clamping system. What does the WMP20S grade indicate? WMP20S denotes Walter’s coated carbide grade optimised for rostfreier Stahl, balancing wear resistance and edge stability for repeatable performance. Walter Tools: Walter AG, Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Mark names and protected goods designations are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The item offered is an original, factory‑new product of the respective manufacturer.
DCMT070204-FM4 WMP30G WMP30G Wendeplatten - Walter Tools
Taking advantage of a coated carbide grade from the Tiger·tec Gold family and a purpose-built FM4 chipbreaker, this insert delivers reliable chip control and extended edge life when machining stainless steels; order via Metav Werkzeuge or consult the specialists for application support. DCMT070204-FM30G (DCMT070204-FM4 WMP30G) turning insert, Tiger·tec Gold — for stainless steel, Walter Tools A DCMT070204-FM4 WMP30G indexable turning insert engineered for medium to robust machining of stainless steels, combining a protective Tiger·tec Gold coating with a dedicated chipbreaker for consistent surface quality. Tiger·tec Gold coated for thermal stability Designed for stainless steel machining Rhombic 55° shape for versatile turning FM4 chipbreaker for controlled chips Consistent performance for stainless steel machining The insert is based on a coated carbide grade from the Tiger·tec Gold series and the WMP30G specification, developed to resist the typical problems encountered with stainless materials such as built-up edge and softening at the cutting edge. This results in a more stable cutting edge and predictable wear behaviour, which in turn reduces unexpected tool changes and supports higher process reliability. The combination of coating technology and substrate composition improves heat resistance and aids in maintaining tolerance and surface quality over longer running times. Geometry optimised for surface finish and chip control The rhombic 55° geometry, paired with a 7° clearance and a 0.4 mm corner radius, delivers a balance between entry strength and fine surface finish. The integrated FM4 chipbreaker is specifically tuned to break and evacuate chips when working with tough stainless steels, helping to avoid entangling chips and promoting continuous cutting. These geometric choices reduce the risk of workpiece damage and simplify post-process handling, making the insert suitable for a wide range of turning operations where consistent results are required. Productivity and process stability as measurable benefits Using a grade and geometry tuned for the M material group yields tangible productivity advantages: more predictable tool life, fewer interruptions for edge changes and improved first-pass yields. The design reduces the tendency for vibratory wear and supports repeatable setups with standard toolholders. In practical terms, shops can benefit from reduced downtime and lower tooling overheads because the insert maintains cutting performance under medium to robust conditions, contributing directly to throughput and cost-effectiveness in production environments. Practical application notes and handling recommendations The insert is designated for the machining of stainless steel (material group M) and performs best when paired with compatible toolholders for rhombic 55° inserts. The small 0.4 mm corner radius provides a compromise between edge strength and surface quality, making it appropriate for finishing to semi-roughing passes depending on the chosen feeds and speeds. For specific cutting parameters and holder compatibility, refer to tooling charts or contact the supplier for tailored recommendations; these measures help to fully exploit the WMP30G grade and its Tiger·tec Gold coating while preventing premature wear. For reliable machining of stainless steels with Walter Tools Tiger·tec Gold inserts, contact Metav Werkzeuge for availability and application advice. Technical data SKU: DCMT070204-FM4-WMP30G-WALTER Article designation: DCMT070204-FM4 WMP30G Product type: Turning insert (indexable) Manufacturer: Walter Tools Series: Tiger·tec Gold Core specifications Clearance angle: 7° Corner radius: 0.4 mm Shape: Rhombic 55° Plate size code: 07 Thickness code: 02 Grade / sort: WMP30G Tolerance class: M Design / Special features Chipbreaker: FM4 Coating technology: Tiger·tec Gold Material group suitability: M (stainless steel) Execution code: T FAQ Which materials is this insert best suited for? The DCMT070204-FM4 WMP30G insert is optimised for stainless steel applications (material group M) thanks to its Tiger·tec Gold grade and FM4 chipbreaker, which promote stable chip formation. What does the FM4 chipbreaker deliver in practice? The FM4 chipbreaker on the insert breaks and evacuates chips effectively when turning stainless steels, reducing chip entanglement and supporting consistent surface finish with fewer interruptions. How does the rhombic 55° geometry affect use? The rhombic 55° form provides versatility across turning tasks: it offers a balance between cutting-edge accessibility and strength, suitable for a range of turning operations from finishing to semi-roughing. Is the insert compatible with standard toolholders? Yes, the insert follows standard indexable turning insert geometry and mounting codes; it is compatible with toolholders designed for DCMT-style inserts, though holder selection should account for required cutting parameters. What is the significance of the WMP30G designation? WMP30G denotes the Walter Tools grade within the Tiger·tec Gold family, chosen for its resistance to built-up edge and thermal load when machining stainless steels; it indicates a coated carbide solution optimised for those conditions. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanation purposes only and do not indicate any affiliation with our company. The offered item is an original, factory-new product from the manufacturer.
DCMT070204-FM4 WSM01 FM4 Wendeplatten - Walter Tools
Benefit from the combination of a thermally robust Tiger‑tec Silver coating and the WSM01 carbide grade for secure cutting in stainless steels and heat‑resistant superalloys; the compact rhombic geometry with 7° relief and FM4 chipbreaker improves surface finish and process reliability. Order directly via Metav Werkzeuge or consult the Metav team for application advice. DCMT070204-FM4 WSM01 indexable turning insert, Tiger‑tec Silver grade for stainless steel and superalloys — Walter Tools The DCMT070204-FM4 WSM01 is an indexable turning insert engineered for machining stainless steel and heat‑resistant superalloys, combining a coated carbide substrate with a chipbreaker geometry for controlled chip formation. Tiger‑tec Silver coating for high thermal resistance WSM01 grade optimised for stainless steel and superalloys Rhombic 55° form with 7° relief for stable cutting FM4 chipbreaker and 0.4 mm corner radius for finish High‑temperature performance that secures chipflow and productivity The combination of the Tiger‑tec Silver coating and the WSM01 grade provides reliable heat resistance and a stable cutting edge when machining materials that tend to work‑harden or produce long, stringy chips. The coated carbide substrate supports consistent wear behaviour under thermal load, reducing the need for frequent insert changes and helping to maintain average cycle times. For production environments where material batches vary, the insert’s metallurgy is chosen to sustain process stability across both stainless steel and superalloys, limiting unexpected downtime and improving repeatability. Geometry optimised to improve surface finish and reduce rework The insert’s rhombic 55° shape combined with 7° relief gives a predictable engagement angle that reduces cutting forces during transverse and light turning operations. The FM4 chipbreaker is designed to fragment and evacuate chips effectively, which supports steady machining even when thermal conductivity of the workpiece is low. The 0.4 mm corner radius balances edge strength and fine surface finish, making the insert suitable for semi‑finishing and finishing passes where control of tool marks and tolerance achievement is essential for downstream operations. Coating and substrate technology that extend tool life A coated carbide construction provides improved wear resistance and thermal stability compared with uncoated alternatives. The Tiger‑tec Silver layer acts as a thermal barrier and reduces adhesion of workpiece material to the cutting edge, supporting longer edge life in challenging alloys. This technical combination increases process security in series production, where consistent edge performance translates directly into fewer interruptions, lower scrap rates and measurably higher productivity. Easy integration into turning systems and predictable results The design of this turning insert aligns with standard toolholder systems for the DCMT 07 family and facilitates quick index changes and re‑identification in toolrooms. The DCMT070204-FM4 WSM01 insert from Walter Tools delivers a reproducible cutting geometry and clear specification for quality assurance routines, which simplifies tool inventory management and makes process documentation straightforward. When paired with appropriate feeds and speeds, the insert supports controlled chip removal and consistent surface quality, contributing positively to overall manufacturing throughput. Contact Metav Werkzeuge to discuss integrating Walter Tools Tiger‑tec Silver inserts into production, request an application recommendation or check material compatibility — info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: DCMT070204-FM4-WSM01-WALTER Designation: DCMT070204-FM4 WSM01 Brand: Walter Tools Series: Tiger‑tec Silver Form: Rhombic 55° Facts Relief angle: 7° Corner radius: 0.4 mm Insert size: 07 Thickness code: 02 Tolerance class: M Special features Chipbreaker: FM4 Grade: WSM01 (coated carbide) Material suitability: stainless steel (M), superalloys/titanium (S) Execution: T FAQ What materials is this insert suitable for? The DCMT070204-FM4 WSM01 is intended for stainless steel (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), where edge stability and thermal resistance are required. Which chipbreaker and corner radius are specified? The insert is supplied with an FM4 chipbreaker and a 0.4 mm corner radius, optimised for controlled chip formation and improved surface finish on semi‑finishing and finishing passes. How does the Tiger‑tec Silver coating affect tool life? The Tiger‑tec Silver coating reduces adhesion and improves thermal stability, which helps to extend edge life and maintain process security when machining materials that generate high temperatures at the cutting zone. Is the geometry suitable for finishing operations? Yes. The rhombic 55° form together with the 0.4 mm corner radius and 7° relief provides a balance of edge strength and low cutting force suitable for fine turning and achieving consistent surface quality. What does tolerance class M mean for machining precision? Tolerance class M indicates the plate’s dimensional tolerance suited for standard production tolerances; it supports repeatable positioning in the toolholder and predictable cutting behaviour. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original, factory‑new goods of Walter Tools.
DCMT070204-FM4 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of high process security, long tool life and predictable chip control for productive turning of stainless steels and superalloys; order the inserts from Metav Werkzeuge or request technical advice for application-specific machining strategies. DCMT070204-FM4 WSM10S turning insert — Rhombic 55°, 7° clearance — Walter Tools (Tiger·tec Silver) The DCMT070204-FM4 WSM10S is a coated carbide turning insert designed for reliable machining of stainless steels and heat-resistant superalloys in demanding production environments Tiger·tec Silver coated carbide Optimised for stainless steels and superalloys Rhombic 55° insert with 0.4 mm corner radius FM4 chipbreaker for controlled chips High-performance cutting for difficult materials The WSM10S grade from the Tiger·tec Silver family combines a coated cemented carbide substrate with an engineered top layer to resist heat and maintain a sharp edge during continuous operation. This makes the insert particularly suitable for ISO group M (stainless steels) and S (heat-resistant superalloys and titanium), where poor thermal conductivity and material toughness demand a coating that supports stable chip formation and reduces the tendency to form built-up edge. The result is increased process reliability and fewer unplanned tool changes. Predictable chip behaviour and improved surface finish The FM4 chipbreaker geometry, paired with a Rhombic 55° form and a 0.4 mm corner radius, delivers consistent chip segmentation and evacuation in turning operations. The 7° clearance angle reduces rubbing on the flank face and helps maintain cutting temperatures within acceptable ranges, which in turn contributes to superior surface quality and reduced rework. Translating geometry and coating into shop-floor benefits: longer uninterrupted cycles and more predictable component tolerances. Practical integration and measurable productivity gains The insert follows standard designation coding and is available in size code 07 with thickness code 02, tolerance class M and execution type T, enabling straightforward toolholder compatibility and inventory management. Using this grade can reduce tooling changes and support higher average metal removal rates on challenging materials, improving overall throughput. For process planners, the combination of Tiger·tec Silver technology and the FM4 geometry offers a reliable balance between edge stability and wear resistance, which supports consistent batch-to-batch performance. Contact Metav Werkzeuge for availability and tailored machining recommendations for Walter Tools inserts — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss cutting data and procurement options Technical data Article number: DCMT070204-FM4-WSM10S-WALTER Designation: DCMT070204-FM4 WSM10S Manufacturer: Walter Tools Data Clearance angle: 7° Corner radius: 0.4 mm Insert shape: Rhombic 55° Size code: 07 Thickness code: 02 Tolerance class: M Special features Coating technology: Tiger·tec Silver Grade: WSM10S (coated cemented carbide) Chipbreaker: FM4 Material groups: ISO M (stainless steels), ISO S (superalloys, titanium) Execution: T Series: Tiger-tec Silver FAQ What materials are best machined with this insert? The DCMT070204-FM4 WSM10S insert is optimised for ISO group M (rostfreier Stahl / stainless steels) and ISO group S (heat-resistant superalloys and titanium), offering stable cutting when machining tough, heat-resistant materials. How does the FM4 chipbreaker benefit production? FM4 geometry promotes controlled chip formation and evacuation; with the DCMT070204-FM4 WSM10S this helps reduce downtime for chip-related issues and improves surface finish consistency. Can this insert be used in standard toolholders for Rhombic 55° inserts? Yes, the insert follows common Rhombic 55° form factors and size coding (07), allowing compatibility with standard toolholders designed for DCMT-style inserts. What does the Tiger·tec Silver coating provide in practice? The Tiger·tec Silver coating on the WSM10S grade improves heat resistance and edge stability, extending tool life during continuous cutting of stainless steels and superalloys. Manufacturer/Responsible: Walter AG (brand: Walter Tools); headquartered in Tübingen, Germany. Protected trademarks and product names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only and do not imply any affiliation between our company and the brands. The offered article is an original, factory-new product of the manufacturer.
DCMT070204-FM4 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of a wear-resistant Tiger·tec Silver grade and a secure FM4 chipbreaker to maintain stable cutting in demanding turning operations; the combination of a Rhombus 55° geometry and a 0.4 mm corner radius supports precise finishes on tough alloys. Order the original insert directly via Metav Werkzeuge or consult their team for process-specific advice. DCMT070204-FM4 WSM20S turning insert — Rhombus 55°, FM4 chipbreaker (Walter Tools) The DCMT070204-FM4 WSM20S is an indexable turning insert with a rhombic 55° form, engineered for robust performance in rostfreier Stahl and heat-resistant alloys Tiger·tec Silver coating performance Optimised FM4 chip control Rhombus 55° for versatile turning Suitable for rostfreier Stahl and superalloys Coating and grade that extend tool life and process reliability The combination of the Tiger·tec Silver series and the WSM20S grade provides a coating system designed to reduce wear and support a stable cutting edge when machining difficult-to-cut materials. This coated cemented carbide grade is formulated for applications involving high heat generation and adhesive tendencies; the result is improved edge stability and longer usable life compared with uncoated alternatives. For production environments where repeatability and minimal downtime matter, the coating’s thermal resilience contributes directly to fewer tool changes and consistent component quality. Geometry and chip control that improve surface finish and safety A Rhombus 55° shape with a 0.4 mm corner radius and a 7° clearance angle yields a balance between robustness and accessibility in a range of turning tasks. The FM4 chipbreaker is shaped to generate predictable chip forms and to prevent long, entangling chips, which reduces the risk of machine interruptions and improves operator safety. This geometry supports fine finishing passes as well as stable roughing, enabling better surface integrity on the workpiece while maintaining cutting forces within manageable limits. Tailored for rostfreier Stahl and heat-resistant superalloys This insert’s specification targets materials classified under ISO group M (rostfreier Stahl) and S (heat-resistant superalloys and titanium). The grade composition and chip control are chosen to address the common issues of these groups — adhesion, poor thermal conductivity and high cutting temperatures. In practice, the insert enables more predictable machining windows, helping to protect the cutting edge during steep thermal and mechanical loading. For workshops that require consistent batch-to-batch performance, the result is higher first-pass yield and reduced rework. Practical advantages for production and tool management Using an insert from the Tiger·tec Silver family with the FM4 chipbreaker supports efficient tool management through extended tool life and reliable process behaviour. The standardised rhombic format simplifies indexable insert stocking and replacement, while the tolerance class M indicates the precision level expected from the component. These attributes together underpin cost-effectiveness in the longer term: fewer tool changes, predictable maintenance intervals and improved machine uptime. For engineering teams focused on productivity and quality, this insert is a pragmatic choice within a controlled machining strategy. Contact Metav Werkzeuge for a process evaluation and tailored recommendations for Walter Tools inserts, including guidance for rostfreier Stahl machining; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: DCMT070204-FM4-WSM20S-WALTER Designation: DCMT070204-FM4 WSM20S Manufacturer: Walter Tools Core specifications Free cutting angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 55° Plate size: 07 Thickness: 02 Tolerance class: M Features Series: Tiger·tec Silver Grade: WSM20S Chipbreaker: FM4 Execution: T Material group: S / M Suitable for rostfreier Stahl Suitable for heat-resistant superalloys and titanium FAQ What materials is this insert suitable for? The DCMT070204-FM4 WSM20S from Walter Tools is suitable for rostfreier Stahl and heat-resistant superalloys, reflecting the grade’s focus on thermal resistance and stable chip formation. How does the FM4 chipbreaker affect machining? The FM4 chipbreaker on this Walter Tools insert produces controlled chip forms that reduce entanglement and support uninterrupted cutting cycles, improving process reliability. What does the 0.4 mm corner radius mean for surface finish? A 0.4 mm corner radius gives improved edge strength for finishing passes while enabling consistent surface quality on turned components when using the DCMT070204-FM4 WSM20S insert. Is this insert part of a larger system for tool management? Yes; the insert belongs to the Tiger·tec Silver series, which is designed for predictable performance and straightforward integration into standard indexable tooling systems from Walter Tools. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are used for explanatory purposes only and do not imply any affiliation between Metav Werkzeuge and the brand owner. The offered article is an original factory-new product of the manufacturer.
DCMT070204-FM4 WSM30S T Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Silver coating and the WSM30S grade for reliable machining of stainless steel and heat‑resistant superalloys; the FM4 chipbreaker and the Rhombus 55° geometry promote secure chip control and consistent surface quality. Order the DCMT070204-FM4 WSM30S turning insert directly via Metav Werkzeuge or ask our consultants if needed. DCMT070204-FM4 WSM30S turning insert — Tiger‑tec Silver, FM4 chipbreaker | Walter Tools DCMT070204-FM4 WSM30S is an indexable turning insert designed for productive machining of stainless steel and heat‑resistant superalloys, combining a robust grade with a heat‑resistant coating for demanding turning tasks. Tiger‑tec Silver coating for heat resistance WSM30S grade for stable cutting edges FM4 chipbreaker for reliable chip control Rhombus 55° geometry with 0.4 mm radius Maximised process reliability through coating and grade The combination of the Tiger‑tec Silver coating and the WSM30S carbide grade delivers a measurable increase in wear resistance and thermal stability during challenging turning operations. This technology is formulated to reduce flank wear and protect the cutting edge when machining tough alloys; as a result, machining cycles become more predictable and interruptions are reduced. The grade supports stable chip formation when working with stainless steel and demanding superalloys, which directly contributes to longer tool life and fewer regrinds—key factors for maintaining throughput and lowering overall production costs. Geometry and clearance engineered for consistent part quality The Rhombus 55° insert form with a 0.4 mm corner radius and 7° clearance provides a balance between cutting strength and accessibility for profile and finishing cuts. The acute geometry enables secure engagement in narrow grooves and interrupted cuts while the small radius helps maintain edge robustness for repeatable surface finishes. Clearances and edge geometry are designed to reduce rubbing and minimise heat generation at the cutting zone, which in turn supports dimensional accuracy and a more uniform surface texture on turned components. Controlled chip formation for safe, efficient machining The FM4 chipbreaker is optimised for medium to heavy turning operations in sticky and heat‑generating materials. Its land and pocket geometry assist in breaking chips into manageable segments and directing them away from the tool‑workpiece interface, lowering the risk of chip entanglement and workpiece damage. Reliable chip control not only improves operator safety but also reduces cycle interruptions and tool wear caused by irregular chip flow, thereby supporting continuous and efficient production runs. Practical application and selection guidance Designation and material suitability follow ISO conventions: the insert covers ISO groups M (stainless steel) and S (heat‑resistant superalloys / titanium), making it appropriate for components that demand thermal stability and edge security. For best results, select insert size and clamping suited to the toolholder and the intended depth of cut; the coded size and thickness should be matched to machine rigidity and part geometry. For specific process parameters or to confirm compatibility with an existing tool system, Metav Werkzeuge offers technical consultation to fine‑tune tool choice and cutting data for improved productivity. Contact Metav Werkzeuge today for tailored recommendations on Walter Tools Tiger‑tec Silver turning inserts and secure consistent process results; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: DCMT070204-FM4-WSM30S-WALTER Designation: DCMT070204-FM4 WSM30S Product type: turning insert Series: Tiger‑tec Silver Grade: WSM30S Manufacturer: Walter Tools Core data Clearance angle: 7° Corner radius: 0.4 mm Insert shape: Rhombus 55° Size code: 07 Thickness code: 02 Tolerance class: M Features Coating: Tiger‑tec Silver Chipbreaker: FM4 Execution: T Material suitability: stainless steel, superalloys (ISO 513 groups M, S) FAQ Is this insert suitable for machining stainless steel? Yes. The DCMT070204-FM4 WSM30S insert is specified for stainless steel (ISO group M) and is formulated to reduce built‑up edge and improve edge life when machining stainless materials. Which workpiece materials are covered by the WSM30S grade? The WSM30S grade addresses both ISO groups S and M, meaning it is suitable for heat‑resistant superalloys and stainless steel where thermal stability and edge robustness are required. What benefit does the FM4 chipbreaker provide in turning operations? The FM4 chipbreaker promotes segmented chip formation and controlled evacuation, lowering the risk of chip entanglement and improving machining continuity for medium to heavy turning. How does the 0.4 mm corner radius affect machining results? A 0.4 mm corner radius increases edge strength for interrupted or semi‑finishing cuts while still allowing good surface finish; it is a compromise between robustness and achievable surface quality. How can the Tiger‑tec Silver series be identified on the insert? Tiger‑tec Silver is the specified coating technology for this range and is referenced together with the grade WSM30S on the DCMT070204-FM4 WSM30S marking; product labelling and catalogue data confirm the series and grade. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and trademarks are mentioned for explanation only. There is no connection between our company and the named brands. The offered item is original, brand‑new goods from the manufacturer Walter Tools.
DCMT070204-FM6 WSM20S WSM20S Wendeplatten - Walter Tools
Robust combination of Tiger·tec Silver coating and the FM6 chipbreaker delivers stable cutting in demanding materials such as rostfreier Stahl and heat‑resistant alloys; the 0.4 mm corner radius and Rhombus 55° form support consistent edge life and versatile turning. Order directly via Metav Werkzeuge or consult the specialists for cutting data and application advice. DCMT070204-FM6 WSM20S — Turning insert, Tiger·tec Silver, Walter Tools DCMT070204-FM6 WSM20S is a coated carbide turning insert designed for demanding machining of rostfreier Stahl and superalloys; suitable for general turning tasks where edge stability and reliable chip control are essential. Tiger·tec Silver coated grade WSM20S FM6 chipbreaker for stable chip control 0.4 mm corner radius for consistent edge life Rhombic 55° form for versatile turning Stable chip control for demanding materials The combination of the FM6 chipbreaker and the Tiger·tec Silver technology produces predictable chip formation and reduced risk of built‑up edge when machining tough alloys. Designed for ISO groups M and S, the insert supports safe cutting of rostfreier Stahl and heat‑resistant superalloys by promoting controlled evacuation of chips and minimising thermal load on the cutting edge. This stability contributes directly to process reliability and fewer unplanned interruptions in production. Longer tool life and reproducible results A coated carbide substrate and the specified 0.4 mm corner radius ensure a durable cutting edge that withstands the mechanical and thermal stresses typical for difficult‑to‑cut materials. With a tolerance class M, the geometry promotes repeatable seating and index changes, helping to reduce variability in finished parts. The result is a lower cost per component through extended index intervals and reliable surface quality over repeated operations. Geometry that adapts to a range of turning tasks The Rhombus 55° insert form with 7° clearance combines a versatile approach angle and secure clamping, enabling both light finishing cuts and tougher profiling operations depending on toolholder and cutting data. The insert size (07) and slim thickness (02) make it suitable for compact toolholders while maintaining adequate rigidity. This geometry supports efficient machining strategies where flexibility across workpiece types is required without frequent tool swaps. Practical specification and process guidance Marked according to ISO 513 group classifications, this insert is optimised for applications where stable cutting edge performance and effective chip control are key selection criteria. Adjustments to feed, speed and depth of cut should account for the workpiece material and toolholder stiffness; consult the technical tables provided by Metav Werkzeuge or the Walter Tools guidelines for initial parameter windows. For customers seeking reproducible productivity in rostfreier Stahl and superalloy applications, the grade WSM20S offers a balanced compromise between wear resistance and toughness. Contact Metav Werkzeuge today for tailor‑made cutting data and to request the DCMT070204-FM6 WSM20S Tiger·tec Silver turning insert from Walter Tools Technical data Article number: DCMT070204-FM6-WSM20S-WALTER Label: Turning insert DCMT070204-FM6 WSM20S Walter Tools Manufacturer: Walter Tools Product type: Turning insert Facts Insert form: Rhombus 55° Corner radius: 0.4 mm Clearance angle: 7° Insert size: 07 Thickness: 02 Grade / Sort: WSM20S Chipbreaker: FM6 Tolerance class: M Materials and features Series: Tiger·tec Silver Coating / surface technology: Tiger·tec Silver (coated carbide) Material suitability: rostfreier Stahl (M), superalloys / titanium (S) Execution: T FAQ What materials is this insert best suited for? The DCMT070204‑FM6 WSM20S insert is suited for rostfreier Stahl and heat‑resistant superalloys (ISO groups M and S), with the WSM20S grade optimised for stable chip formation in these materials. How does the FM6 chipbreaker influence machining? The FM6 chipbreaker on the DCMT070204‑FM6 promotes controlled chip shapes and evacuation, reducing the likelihood of built‑up edge and improving surface consistency during turning operations. What benefits does the Tiger·tec Silver series provide? The Tiger·tec Silver technology offers a coated carbide balance of wear resistance and toughness, extending tool life and supporting reproducible performance in demanding cutting conditions. Is the 0.4 mm corner radius suitable for finishing? Yes, the 0.4 mm corner radius provides a compromise between edge strength and surface finish, making it appropriate for many finishing and medium‑duty turning applications. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT070204-FM6 WSM30S FM6 Wendeplatten - Walter Tools
Combine the thermal resilience of the Tiger·tec Silver coating with the WSM30S grade optimised for stainless steel and heat‑resistant alloys, plus the FM6 chipbreaker for controlled chip formation — a combination that supports productive turning and reliable tool life; order directly via Metav Werkzeuge or consult our specialists for application advice. DCMT070204-FM6 WSM30S turning insert, Rhombic 55° geometry, Tiger·tec Silver — Walter Tools A DCMT070204-FM6 WSM30S turning insert engineered for heavy and difficult turning applications, particularly suited to stainless steel and heat‑resistant superalloys where thermal stability and chip control are critical Tiger·tec Silver coating for heat resistance and wear control WSM30S grade optimised for stainless steel and superalloys FM6 chipbreaker for predictable chip formation Rhombic 55° form with 7° relief and 0.4 mm corner radius Productive machining of tough alloys with reduced risk of built‑up edge The combination of the Tiger·tec Silver coating and the WSM30S grade provides enhanced thermal resistance and wear performance during continuous and semi‑continuous turning. This coated carbide formulation is designed to resist the high temperatures that develop when machining stainless steel and nickel‑based superalloys, supporting a stable cutting edge and lowering the incidence of built‑up edge. The result is more consistent tool life and reduced process interruptions, which translates into higher throughput and less downtime on demanding production runs. Geometry that balances surface finish and robustness The rhombic 55° insert geometry, paired with a corner radius of 0.4 mm and 7° relief, delivers a balance between accuracy and edge strength. The moderate corner radius supports good surface integrity while preserving edge robustness under intermittent load. The FM6 chipbreaker is engineered for controlled chip segmentation, helping to avoid long, tangled swarf and improving secure evacuation of chips in both continuous and interrupted cuts. For shops aiming for consistent dimensional results, this geometry aids repeatable finishes with reduced need for secondary operations. Application advice and process benefits for production environments Specified for groups M and S in ISO material classification, this insert is particularly suitable for stainless steel and heat‑resistant alloys and titanium when the right cutting parameters are applied. The coated carbide grade and chipbreaker together promote efficient heat dissipation and predictable chip form, which reduces pressure on clamping systems and toolholders. Process planners will appreciate the insert’s contribution to stable machining windows, while operators benefit from fewer unplanned tool changes. The insert’s tolerance class M indicates manufacturing precision that supports interchangeability within defined tool systems. Contact Metav Werkzeuge today to discuss the Walter Tools DCMT070204-FM6 WSM30S insert for stainless steel applications and receive tailored recommendations or cutting data via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: DCMT070204-FM6-WSM30S-WALTER Designation: DCMT070204-FM6 WSM30S Product type: Turning insert (Drehwendeschneidplatte) Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.4 mm Insert shape: Rhombic 55° Size code: 07 Thickness code: 02 Tolerance class: M Special features Coating: Tiger·tec Silver Grade: WSM30S (coated carbide) Chipbreaker: FM6 Material suitability: stainless steel (M), S (superalloys / titanium) Series: Tiger‑tec Silver Execution: T FAQ Which materials is this insert designed to machine? The DCMT070204‑FM6 WSM30S insert is designed for stainless steel (ISO group M) and for heat‑resistant superalloys and titanium (ISO group S), offering thermal stability and edge control in demanding materials. What benefit does the FM6 chipbreaker provide? The FM6 chipbreaker on this Walter Tools insert promotes segmented, controllable chips for safer evacuation and reduced risk of entanglement, improving productivity and surface consistency. How does the Tiger·tec Silver coating affect tool life? The Tiger·tec Silver coating enhances thermal resistance and reduces abrasive wear on the cutting edge, which helps to extend tool life and maintain cutting performance in high‑temperature turning operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik‑Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT070204-FP4 WEP10C WEP10C Wendeplatten - Walter Tools
Take advantage of the combination of WEP10C cermet performance and the FP4 chipbreaker for consistent chip control and superior surface quality; order directly via Metav Werkzeuge or consult Metav Werkzeuge for application-specific recommendations. DCMT070204-FP4 WEP10C Indexable turning insert — Walter Tools, Walter Cermet, FP4 chipbreaker A DCMT070204-FP4 WEP10C indexable turning insert designed for fine finishing and reliable medium-duty turning within the Walter Cermet series, optimised for predictable chip formation and long tool life Walter Cermet series, WEP10C cermet grade Rhombic 55° geometry for stable cutting FP4 chipbreaker for controlled chip formation 7° clearance angle for precise finishing Higher process stability through cermet precision The WEP10C cermet composition delivers a balance between wear resistance and toughness that benefits finishing operations. As a cermet-based grade, it supports sustained cutting-edge integrity under moderate cutting speeds, which results in improved surface quality and fewer rework cycles. The insert’s formulation and the Walter Cermet series aim to reduce flank wear during long runs, contributing to predictable tool life and consistent component tolerances. Controlled chips and safer machining Equipped with the FP4 chipbreaker, the insert enables controlled chip formation, reducing the likelihood of entangling long chips and improving evacuation in automated or semi-automated turning processes. The Rhombic 55° shape provides a stable cutting platform that balances entry angle and strength, while the corner radius 0.4 mm aids in achieving fine surface finishes without inducing excessive cutting forces. These characteristics enhance process reliability and make the insert suitable for batch production where chip control and repeatability matter. Geometry and angles that support precision finishing The geometry—rhombic form and 7° clearance—is selected to favour precision finishing tasks while maintaining sufficient edge strength for medium-duty turning. A moderate clearance angle helps to reduce rubbing on the flank face and lowers heat transfer to the cutting edge, which supports dimensional stability across a production run. The insert’s size and thickness parameters accommodate standard turning toolholders, enabling straightforward integration into existing setups with appropriate clamping. Practical application and selection guidance This indexable insert is intended for applications where a fine surface and consistent part quality are priorities. The FP4 chipbreaker combined with the WEP10C grade is particularly effective on materials where a sharp yet durable cutting edge is needed; suitability for specific alloys should be verified in the product matrix. For shops aiming to streamline finishing operations and reduce rework, the insert represents a technically robust option that balances productivity with surface integrity. Contact Metav Werkzeuge today for tailored advice on integrating Walter Tools DCMT070204-FP4 WEP10C inserts into production and to discuss available quantities and compatible toolholders Technical overview SKU: DCMT070204-FP4-WEP10C-WALTER Designation: DCMT070204-FP4 WEP10C Type: Indexable turning insert Brand: Walter Tools Core specifications Free angle: 7° Corner radius: 0.4 mm Insert size: 07 Thickness: 02 Geometry: Rhombus 55° Tolerance class: M Materials & special features Grade: WEP10C cermet Series: Walter Cermet Chipbreaker: FP4 Execution: T Material: Katalogabhängig Intended for: Check product matrix for suitability FAQ What materials is this insert suitable for? The DCMT070204-FP4 WEP10C insert, part of the Walter Cermet series, is designed for a range of materials; specific suitability should be confirmed against the Walter product matrix for the WEP10C grade. What is the corner radius and how does it affect finishing? The insert features a corner radius of 0.4 mm, which helps achieve smoother surfaces and reduces the risk of chatter in finishing operations while maintaining adequate edge strength. How does the FP4 chipbreaker improve machining? The FP4 chipbreaker promotes controlled chip formation and easier evacuation, improving safety and reducing interruptions in automated and manual turning processes. Which geometry is used and why does it matter? A rhombic 55° geometry provides stable cutting conditions with a favourable balance between edge strength and accessibility, supporting consistent part quality during medium-duty turning. Can this insert be used in standard toolholders? The insert’s dimensions and form are compatible with commonly used turning toolholders for inserts of this designation; check holder compatibility and clamping specifications before assembly. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT070204-FP4 WKP01G WKP01G Wendeplatten - Walter Tools
Take advantage of a Tiger·tec Gold grade that combines extended tool life with consistent edge stability and the FP4 chipbreaker for reliable chip control in mixed production runs; order the DCMT070204-FP4 WKP01G turning insert via Metav Werkzeuge or consult the technical team for cutting data and availability. DCMT070204-FP4 WKP01G turning insert — FP4 chipbreaker, Tiger·tec Gold (Walter Tools) The DCMT070204-FP4 WKP01G is a coated carbide turning insert engineered for efficient machining of steel and cast iron, delivering stable chip formation and repeatable surface quality. Tiger·tec Gold coating for extended tool life Optimised FP4 chipbreaker for stable chips Suitable for steel and cast iron (ISO P/K) Rhombic 55° form with 0.4 mm corner radius Increased productivity through a wear-resistant grade The Tiger·tec Gold grade provides a coated carbide chemistry designed to resist abrasive wear and preserve a stable cutting edge under typical steel and cast iron cutting conditions. The combination of coating technology and carbide substrate reduces flank wear and extends usable life, which in turn lowers tool change frequency and supports uninterrupted production cycles. For applications that prioritise throughput and consistent cycle times, this insert delivers measurable efficiency gains while maintaining surface integrity. Predictable chip control and improved surface finish The FP4 chipbreaker geometry has been developed to promote short, controllable chips when machining a broad range of steels and cast irons (ISO P/K). Controlled chip evacuation reduces the risk of re-cutting and minimizes manual cleaning between operations, helping to protect both the workpiece and adjacent tooling. The rhombic 55° cutting geometry combined with a 0.4 mm corner radius supports reliable entry and exit behaviour, which contributes to consistent dimensional accuracy and improved part-to-part repeatability in serial production. Practical selection and application advice for machining tasks When integrating this insert into existing toolholders, the rhombic profile and the 7° clearance angle ensure straightforward seating and predictable cutting forces for many common turning operations. The M tolerance class ensures compatibility with standard toolholders and repeatable indexability, simplifying inventory management. For process qualification, selecting cutting parameters that match workpiece material and machine rigidity will make full use of the grade’s abrasion resistance and chip control features; Metav Werkzeuge can provide application-specific recommendations if required. For reliable results and tailored cutting parameters, contact Metav Werkzeuge to request availability, batch pricing or detailed machining data for the Walter Tools DCMT070204-FP4 WKP01G insert — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 Technical data Article number: DCMT070204-FP4-WKP01G-WALTER Designation: DCMT070204-FP4 WKP01G Manufacturer: Walter Tools Series: Tiger·tec Gold Grade: WKP01G Core specifications Clearance angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 55° Plate size: 07 Plate thickness: 02 Tolerance class: M Features and applications Chipbreaker: FP4 Coating: Tiger·tec Gold (coated carbide) Material suitability: Steel (ISO P), Cast iron (ISO K) Execution: T Product type: Turning insert (drehwendeschneidplatte) FAQ What materials is this insert suitable for? The DCMT070204-FP4 WKP01G insert from Walter Tools is specified for machining steel (ISO P) and cast iron (ISO K) applications, utilising the Tiger·tec Gold grade for abrasion resistance. How does the FP4 chipbreaker affect machining? The FP4 chipbreaker on this insert promotes short, controllable chips and smoother evacuation, which improves process reliability and reduces the likelihood of chip-related interruptions. What are the key geometric details to consider when choosing a holder? Select a holder that accepts a rhombic 55° insert with a 0.4 mm corner radius and supports the M tolerance class to ensure secure seating and stable cutting forces. Is this insert suitable for high-production environments? Yes; the combination of the Tiger·tec Gold coating and the stable FP4 chip control makes the grade well suited to continuous production where tool life and consistent surface quality are priorities. Can this insert be indexed multiple times? The DCMT070204-FP4 WKP01G is designed for indexable use; the M tolerance and standard rhombic form facilitate repeated indexing in compliant toolholders. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
DCMT070204-FP4 WPP10G WPP10G Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold coating for extended edge life and the FP4 chipbreaker for predictable chip control; this delivers consistent productivity and lower tool costs per component. Order the insert directly via Metav Werkzeuge or consult our specialists for application advice. DCMT070204-FP4 WPP10G turning insert — Tiger‑tec Gold coated, FP4 chipbreaker | Walter Tools A DCMT070204-FP4 WPP10G turning insert engineered for efficient steel turning, offering controlled chip formation and enhanced tool life thanks to its Tiger‑tec Gold technology. Rhombus 55° cutting geometry Tiger‑tec Gold coated carbide FP4 chipbreaker for stable chips 7° clearance and 0.4 mm radius Maximum performance with predictable tool life The DCMT070204-FP4 WPP10G combines a wear‑resistant Tiger‑tec Gold coating with a robust grade designed for steel turning. The coated carbide construction provides high abrasion resistance and thermal stability, which reduces flank wear and prolongs edge life. As a result, machining cycles run longer between indexings, decreasing downtime and contributing to a lower cost per part without compromising productivity or repeatability. Consistent chip control and improved surface quality The integrated FP4 chipbreaker is optimised for the cut conditions typical when machining steel (ISO P). It promotes short, controllable chips and reduces the risk of built‑up edge, which in turn improves surface finish and protects the workpiece geometry. For shops seeking reliable repeatability, the combination of chipformer design and coated substrate supports stable cutting forces and consistent results across varying batch sizes. Clear application scope and material compatibility This grade is specifically matched to steel machining requirements and is suitable for a broad range of steel alloys, including both unalloyed and alloyed steels. The insert’s designation highlights suitability for ISO P materials, meaning the geometry and coating were chosen to manage the heat and chip formation typical for these alloys. Selecting this insert helps to standardise tool setups for steel turning operations and simplifies process planning. Easy integration and robust cutting geometry The Rhombus 55° geometry with a 7° clearance angle and a 0.4 mm corner radius offers a balance between strength and cutting accessibility. The moderate corner radius provides edge reinforcement for interrupted cuts while still enabling fine finishing passes. The insert’s construction and tolerance class M ensure straightforward mounting in common tool holders and predictable positioning, helping to accelerate tool changeovers and maintain machine uptime. For tailored recommendations on Walter Tools Tiger‑tec Gold inserts and to arrange next‑day availability via Metav Werkzeuge, contact our technical team for precise application support Technical data Article number: DCMT070204-FP4-WPP10G-WALTER Designation: DCMT070204-FP4 Full designation: DCMT070204-FP4 WPP10G Manufacturer: Walter Tools Product type: Turning insert Core dimensions Plate size: 07 Plate thickness: 02 Corner radius: 0.4 mm Clearance angle: 7° Plate form: Rhombus 55° Tolerance class: M Features & materials Chipbreaker: FP4 Coating: Tiger‑tec Gold (coated carbide) Material group: Steel (ISO P) Series: Tiger‑tec Gold FAQ What materials is this insert suitable for? This insert is designed for machining steel (ISO P); the WPP10G grade and Tiger‑tec Gold coating are optimised for typical steel cutting conditions. How does the FP4 chipbreaker affect performance? The FP4 chipbreaker produces short, controlled chips that improve surface finish and reduce the likelihood of built‑up edge when turning steel. Is the insert compatible with standard tool holders? Yes, the Rhombus 55° geometry and tolerance class M allow the insert to be used in common turning tool holders that accept DCMT‑style indexable inserts. What benefits does the Tiger‑tec Gold coating provide? The Tiger‑tec Gold coating increases abrasion resistance and thermal stability, extending edge life and helping to maintain consistent cutting performance over longer runs. Can this insert be used for finishing and semi‑finishing? With a 0.4 mm corner radius and the Rhombus 55° geometry, the insert is suitable for both semi‑finishing and controlled finishing passes in steel applications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original, factory‑new goods from the manufacturer.
DCMT070204-FP4 WPP20G FP4 Wendeplatten - Walter Tools
Benefit from the reliable combination of a Tiger‑tec Gold coating and a versatile WPP20G grade for productive steel turning; the FP4 chipbreaker and Rhombic 55° geometry deliver consistent chip control and secure clamping. Order the insert directly via Metav Werkzeuge or consult our specialists for application advice. DCMT070204-FP4 WPP20G indexable turning insert – Rhombic 55°, 7° clearance (Walter Tools) A DCMT070204-FP4 WPP20G indexable turning insert engineered for productive machining of steel with a Tiger‑tec Gold coated carbide grade and a medium‑range FP4 chipbreaker for stable chip formation and process security Tiger·tec Gold coating for extended tool life Rhombic 55° geometry for secure clamping FP4 chipbreaker for consistent chip control 7° clearance angle for reduced rubbing High cutting performance through advanced coating and grade The combination of Tiger‑tec Gold technology and the WPP20G coated carbide grade gives the insert high wear resistance and stable cutting-edge behaviour when machining steel (ISO group P). The multi-layer coating reduces friction and thermal load, enabling higher cutting speeds and longer tool life compared with uncoated grades. For production environments this translates into fewer indexings per component and improved process reliability, while the coated structure supports predictable flank wear for straightforward tool-life planning. Geometry and chip control that improve surface quality and process stability The Rhombic 55° form with a 0.4 mm corner radius and the dedicated FP4 chipbreaker combine to manage chip formation and cutting forces in medium to general turning applications. The modest 7° clearance angle reduces flank contact and prevents built‑up edge on the cutting face, producing a more consistent surface finish. The chipbreaker’s geometry is designed for controllable curling and evacuation, which lowers the risk of chip entanglement in automated machining cells and supports repeatable results across shifts. Practical advantages for production shops and machining centres With a robust grade and user‑friendly geometry the insert supports economical machining routines: fewer tool changes, predictable reconditioning cycles and a tolerance class M that suits general turning tasks. The insert is delivered in the common DCMT shape that fits standard toolholders, easing integration into existing tool inventories. For those seeking process optimisation, the insert’s mix of wear resistance and chip control reduces downtime and helps maintain consistent part quality across batch production runs — a tangible contribution to throughput and cost efficiency. Contact Metav Werkzeuge for tailor-made cutting data and to secure genuine Walter Tools Tiger‑tec Gold turning inserts for immediate use in production Technical data SKU: DCMT070204-FP4-WPP20G-WALTER Label: Drehwendeschneidplatte DCMT070204-FP4 WPP20G Walter Tools Manufacturer: Walter Tools Product type: Indexable turning insert Series: Tiger‑tec Gold Grade: WPP20G Core specifications Clearance angle: 7° Corner radius: 0.4 mm Plate form: Rhombic 55° Plate size: 07 Plate thickness: 02 Tolerance class: M Special features Chipbreaker: FP4 Coating technology: Tiger·tec Gold Material group application: Steel (P) Design designation: DCMT070204-FP4 Execution: T FAQ What materials is the insert suitable for? The DCMT070204‑FP4 WPP20G is designed primarily for steel (ISO group P) machining and the WPP20G grade and Tiger‑tec Gold coating are optimised for typical steel cutting temperatures and chip formation. Which toolholder type fits this insert? The insert uses the common DCMT geometry; it is compatible with toolholders designed for rhombic 55° indexable turning inserts with the corresponding clamping method. How does the FP4 chipbreaker affect machining? The FP4 chipbreaker provides controlled chip curling and evacuation for medium turning operations, improving process stability and reducing the risk of chip entanglement in automated setups. Is the insert suitable for finishing operations? With a 0.4 mm corner radius and the Tiger‑tec Gold coating, the insert is appropriate for general finishing and semi‑finishing where a balance of surface quality and tool life is required. What does the Tiger‑tec Gold series offer compared with standard grades? Tiger‑tec Gold provides enhanced thermal stability and reduced friction, which allow higher cutting parameters and longer tool life in many steel machining applications. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original, factory‑new goods of the manufacturer.
DCMT070204-FP6 WPP10G FP6 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a controlled FP6 chipbreaker and a compact rhombic form for reliable steel machining; order the insert directly via Metav Werkzeuge or request application advice from our consultants. DCMT070204-FP6 WPP10G – Rhombic 55° turning insert with Tiger·tec Gold coating by Walter Tools The DCMT070204-FP6 WPP10G is a coated carbide turning insert engineered for precision machining of steel, offering stable chip formation and predictable cutting behaviour in general turning applications Tiger·tec Gold WPP10G coating Optimised for steel machining FP6 chipbreaker for controlled chips Rhombic 55° geometry, 0.4 mm radius Increase throughput with reliable chip control The combination of the WPP10G cutting grade and the FP6 chipbreaker delivers consistent chip formation during longitudinal and rough turning of steel. The Tiger·tec Gold coating enhances thermal stability and wear resistance, which reduces unplanned tool changes and supports longer uninterrupted cycles. With a chipformer designed for typical steel chip morphology, the insert enables smoother evacuation of chips and lower risk of built-up edge. These factors translate into improved machining efficiency and a more predictable production flow. Longer tool life through advanced coated carbide technology The coated carbide substrate, paired with the Tiger·tec Gold technology, provides enhanced resistance to abrasive wear and flank damage. The rhombic 55° geometry and the modest 0.4 mm corner radius balance strength and edge robustness, allowing productive feeds without compromising surface finish. The tolerance class M ensures consistent dimensions for repeatable insert seating and clamping in standard toolholders, supporting reproducible component quality and reduced setup variation. Easy integration and clear material suitability Marked for ISO P (steel) applications, the insert’s compact format (size 07, thickness 02) fits a wide range of turning toolholders designed for rhombic 55° inserts. The combination of geometry and coating means the insert is suitable for both general finishing and semi‑roughing where cost-effective performance is required. The product’s specification supports process standardisation: predictable cutting results, manageable tool inventories and clear grade selection reduce engineering time and simplify tool management on the shop floor. For dependable steel turning with Walter Tools’ Tiger·tec Gold grade, contact Metav Werkzeuge for ordering and machining recommendations at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: DCMT070204-FP6-WPP10G-WALTER SKU: DCMT070204-FP6-WPP10G-WALTER Designation: DCMT070204-FP6 WPP10G Product type: Turning insert Brand: Walter Tools Numbers / Core technical data Clearance angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 55° Plate size: 07 Plate thickness: 02 Tolerance class: M Designs / Special features Coating: Tiger·tec Gold Grade: WPP10G Chipbreaker: FP6 Execution: T Material application: Steel (ISO P) Series: Tiger‑tec Gold FAQ What materials is this insert suitable for? The DCMT070204-FP6 WPP10G from Walter Tools is specified for ISO P materials, primarily unalloyed and alloyed steel, where the Tiger·tec Gold coating supports typical steel cutting temperatures and chip behaviour. How does the FP6 chipbreaker affect performance? The FP6 chipbreaker on the Walter Tools insert creates controlled chips for reliable evacuation and reduced risk of entanglement, improving surface quality and cycle stability during steel turning. Which geometry and edge radius does the insert use? The insert features a rhombic 55° form with a 0.4 mm corner radius, offering a compromise between edge strength and the ability to achieve fine surface finishes in turning operations. Is the DCMT070204-FP6 WPP10G compatible with standard holders? Yes, the DCMT070204-FP6 format is a standard rhombic 55° turning insert and is compatible with holders designed for this insert designation, provided clamping dimensions match the tolerance class M. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes and to describe compatibility or origin; there is no connection between our company and the named brands. The offered item is an original, brand‑new product from Walter Tools.
DCMT070204-FP6 WPP20G FP6 Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold coating, proven FP6 chip control and a 0.4 mm corner radius for consistent, economical steel turning; order via Metav Werkzeuge or consult our experts for application-specific cutting data. DCMT070204-FP6 DCMT070204-FP6 WPP20G — indexable turning insert for steel, Tiger‑tec Gold by Walter Tools A DCMT070204-FP6 WPP20G indexable turning insert engineered for steel machining, providing reliable chip control and wear resistance in general turning operations Tiger‑tec Gold coated carbide Optimised for steel (ISO P) Rhombic 55° insert, 7° clearance 0.4 mm corner radius, FP6 chipbreaker Stable machining performance for steel turning The coated carbide grade from the Tiger‑tec Gold family delivers a balance of wear resistance and toughness that suits a wide range of steel turning tasks. Designed for the ISO P group, this insert manages the typical heat and chip formation encountered when machining unalloyed and alloyed steels. The FP6 chipbreaker supports consistent chip control, reducing the risk of built-up edge and improving process stability. For production environments seeking repeatable results, the combination of coating technology and chip geometry reduces the need for frequent tool changes and contributes to predictable tool life. Productivity advantages and practical benefits With a Rhombic 55° geometry and 7° clearance, the insert offers good accessibility for general turning profiles while maintaining robust edge support. The 0.4 mm corner radius is a versatile specification that assists in delivering acceptable surface finishes while offering edge strength under moderate cutting forces. The coated carbide substrate helps extend cutting intervals, which supports continuous operation and can lower overall machining costs through reduced downtime and fewer insert replacements. Application guidance and material suitability This insert is intended primarily for steel applications, as indicated by the ISO P designation. The WPP20G grade represents a universal, wear-resistant coated carbide suitable for typical turning operations across a range of steel grades. When selecting cutting data, consider the workpiece material, machining strategy and required surface quality; modest feeds combined with stable clamping and appropriate coolant use will help to exploit the insert’s Tiger‑tec Gold performance. For specific process parameters or trial recommendations, refer to product documentation or contact the technical team for tailored advice. For high-process reliability in steel turning, contact Metav Werkzeuge to request the Walter Tools DCMT070204-FP6 WPP20G insert and obtain personalised cutting data from our specialists via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: DCMT070204-FP6-WPP20G-WALTER Designation: DCMT070204-FP6 WPP20G Manufacturer: Walter Tools Data Clearance angle: 7° Corner radius: 0.4 mm Insert form: Rhombic 55° Chipbreaker: FP6 Size code: 07 Thickness code: 02 Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WPP20G (coated carbide) Material group: ISO P (steel) Execution: T Balanced wear resistance and toughness for general turning FAQ What materials is this insert suitable for? The insert is formulated for the ISO P group and is therefore suitable for turning steel; the WPP20G grade is optimised for typical steel machining conditions. Which features improve chip control with this insert? Chip control is achieved through the FP6 chipbreaker and the insert geometry; these features on the DCMT070204-FP6 help produce manageable chips and stable cutting conditions. How does the Tiger‑tec Gold coating benefit productivity? The Tiger‑tec Gold coating enhances wear resistance and edge life, enabling longer cutting intervals and more consistent performance in steel turning applications. What does the 0.4 mm corner radius mean for surface finish and strength? A 0.4 mm corner radius offers a compromise between edge strength and achievable surface finish, suitable for many general turning tasks where both durability and acceptable finish are required. Is this insert suitable for heavy interrupted cuts or finishing passes? The WPP20G grade is a universal coated carbide: it provides good edge robustness for routine interrupted cuts and stable performance for many finishing applications in steel. For severe interruptions or specialised finishing, adjust cutting data or consult technical support. Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanatory purposes only; there is no affiliation between our company and Walter Tools. The offered article is original, brand-new goods from the manufacturer. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
DCMT070204-FW4 WKP01G Wendeplatten - Walter Tools
Taking advantage of the Tiger·tec Gold coating and the WKP01G grade delivers high process reliability and stable chip control in machining of Stahl and Gusseisen; combine this with the secure Rhombus 55° geometry for consistent part quality and order directly via Metav Werkzeuge or consult our technical team for application support DCMT070204-FW4 WKP01G – turning insert (for Stahl and Gusseisen) · Walter Tools DCMT070204-FW4 WKP01G is an indexable turning insert engineered for efficient, repeatable turning operations on Stahl and Gusseisen, offering a balance of wear resistance and process security Tiger·tec Gold coating for long tool life WKP01G grade optimised for Stahl and Gusseisen Rhombus 55° geometry for secure clamping 0.4 mm corner radius for consistent surface finish Higher throughput thanks to Tiger·tec Gold and WKP01G The combination of the Tiger·tec Gold coating and the WKP01G carbide grade provides a measurable improvement in cutting-edge stability and tool life. The advanced coating reduces flank wear and improves thermal resistance, which translates into fewer tool changes and more consistent cycle times. For production environments that prioritise throughput and repeatable part quality, this coating-grade pairing reduces downtime and supports predictable maintenance planning. The result is efficient material removal with reduced risk of thermal-driven edge breakdown. Reliable surface quality from optimised geometry and chip control The Rhombus 55° form with a 0.4 mm corner radius and a 7° clearance angle offers stable cutting engagement and repeatable chamfered edges. The FW4 chipbreaker ensures controlled chip formation, reducing the likelihood of built-up edge and improving surface finish. These geometric choices support a secure clamping interface and promote dimensional stability across runs. In practical terms, operators benefit from fewer rejects and less rework when machining components that require consistent tolerances. Versatile application range and predictable performance Designed as an indexable solution, the insert is suitable for a wide range of turning tasks on Stahl and Gusseisen, conforming to the expected behaviour of P and K groups per ISO 513. The designation DCMT070204-FW4 identifies the insert geometry and the chipbreaker, simplifying tool selection and inventory management. The toleranzklasse M supports general-purpose turning operations where a balance of accuracy and robustness is required. Availability of a standardised insert reduces setup complexity and helps maintain steady production flows. Contact Metav Werkzeuge to specify the optimal Walter Tools Tiger·tec Gold insert for applications in Stahl and Gusseisen; technical advisers are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: DCMT070204-FW4-WKP01G-WALTER Name: Drehwendeschneidplatte DCMT070204-FW4 WKP01G Walter Tools WPL designation: DCMT070204-FW4 WKP01G Manufacturer: Walter Tools Series: Tiger-tec Gold Facts Free angle: 7° Corner radius: 0.4 mm Plate size: 07 Plate thickness: 02 Tolerance class: M Special features Coating: Tiger·tec Gold (coated carbide) Grade: WKP01G Chipbreaker: FW4 Geometry: Rhombus 55° Material suitability: Stahl; Gusseisen Execution: T FAQ Which materials are recommended for this insert? The DCMT070204-FW4 WKP01G turning insert from Walter Tools is specified for machining Stahl and Gusseisen according to the P and K designations in ISO 513. What does WKP01G indicate? WKP01G is the Walter Tools carbide grade within the Tiger·tec Gold family; it is a coated hardmetal grade optimised for good wear resistance and stable chip formation on Stahl and Gusseisen. What are the key geometry values to note? The insert features a Rhombus 55° form, a corner radius of 0.4 mm and a free angle of 7°, combined with the FW4 chipbreaker for controlled chips. Is this insert suitable for high-production environments? Yes, the Tiger·tec Gold coating and WKP01G grade are designed to enhance tool life and process reliability, making the insert appropriate for continuous production runs involving Stahl and Gusseisen. Manufacturer/Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The item offered is an original, brand-new product of the manufacturer Walter Tools.
DCMT070204-FW4 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance, precise FW4 chip control and stable rhombic geometry for predictable turning performance; order directly via Metav Werkzeuge or contact the consultants for specification support. DCMT070204-FW4 WPP10G Drehwendeschneidplatte – Tiger·tec Gold coated turning insert, FW4 chipbreaker | Walter Tools The DCMT070204-FW4 WPP10G is a rhombic 55° turning insert with a Tiger·tec Gold coating optimised for steel turning applications. Tiger·tec Gold coating for prolonged wear resistance FW4 chipbreaker for consistent chip formation Rhombic 55° geometry for versatile turning tasks 0.4 mm corner radius for robust edge performance Improved process stability through advanced coating technology The Tiger·tec Gold grade WPP10G combines a coated cemented carbide substrate with a multilayer surface treatment that prolongs tool life under the thermal and mechanical loads typical when machining steel. This specification reduces flank wear and preserves the cutting edge, which leads to longer uninterrupted production runs and fewer insert changes. The overall effect is a measurable increase in process stability and repeatable component tolerances, supporting higher throughput and more predictable machining cycles. Reliable chip control and consistent surface quality The dedicated FW4 chipbreaker and the rhombic 55° geometry are designed to deliver controlled chip formation and steady cutting forces. The modest relief angle of 7° and the 0.4 mm corner radius help maintain a robust cutting edge while supporting surface finish requirements during medium to light turning operations. As a result, components emerge with uniform surface characteristics and reduced need for rework, while chip flow remains manageable across typical steel grades specified for this insert. Compact format for easy integration and repeatable performance With the standard DCMT form factor and compact dimensions, this insert suits a wide range of common toolholders and turning applications. The nominal plate size and thickness provide a conservative cutting edge that balances strength and accessibility in confined turning situations. Supplied in tolerance class M with execution T, the insert offers consistent seating accuracy and interchangeability, enabling straightforward inventory management and reliable repeatability across batches. For tailored application advice or to specify Walter Tools Tiger·tec Gold inserts for steel machining, contact Metav Werkzeuge for prompt technical guidance and procurement support via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: DCMT070204-FW4-WPP10G-WALTER Label: Drehwendeschneidplatte DCMT070204-FW4 WPP10G Walter Tools Manufacturer: Walter Tools Facts Geometry: Rhombic 55° Relief angle: 7° Corner radius: 0.4 mm Chipbreaker: FW4 Grade/Coating: WPP10G / Tiger·tec Gold Plate size: 07 Plate thickness: 02 Tolerance class: M Execution: T Special features Suitable material group: steel (P) Coated cemented carbide grade Designed for consistent chip control Optimised for general turning operations FAQ What materials is this insert suited for? The insert is specified for the steel material group (P); the WPP10G Tiger·tec Gold grade is optimised for unalloyed and alloyed steels. How does the FW4 chipbreaker affect machining? The FW4 chipbreaker promotes predictable chip formation and easier chip evacuation, improving surface quality and reducing secondary operations for turning steels. Can the insert handle heavy roughing cuts? The combination of the rhombic 55° geometry and a 0.4 mm corner radius gives the insert a robust edge for many turning tasks, though extreme heavy-duty roughing may require a larger radius or different grade. Is the grade suitable for interrupted cuts or mixed operations? The coated carbide grade with Tiger·tec Gold provides enhanced wear resistance and good edge strength, which supports mixed and intermittent cutting typical in many production environments. How is repeatability ensured when replacing inserts? Tolerance class M and the standard DCMT form ensure consistent seating and repeatable positioning in compatible toolholders, supporting stable part-to-part accuracy. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT070204-FW4 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WPP20G grade for consistent, wear-resistant performance in steel turning; the FW4 chipbreaker and Rhombus 55° form ensure reliable chip control and stable cutting action. Order directly via Metav Werkzeuge or contact the consultants for application support. DCMT070204-FW4 WPP20G indexable turning insert for steel machining — Walter Tools, Tiger·tec Gold, FW4 chipbreaker The DCMT070204-FW4 WPP20G is an indexable turning insert designed for productive steel machining with a Tiger·tec Gold coated carbide grade, an FW4 chipbreaker and Rhombus 55° geometry Tiger·tec Gold coated grade WPP20G FW4 chipbreaker for reliable chip control Rhombus 55° form for versatile turning operations 7° clearance angle and 0.4 mm corner radius Consistent wear resistance for uninterrupted production The WPP20G grade, part of the Tiger·tec Gold series, combines a hard, coated carbide substrate with a coating strategy tuned for machining steel. This formulation provides improved wear resistance and stable edge life, which reduces unplanned tool changes and supports predictable scheduling on the shopfloor. The result is a more consistent surface finish when turning a wide range of steels, and fewer interruptions in batch production. For procurement and tool-room managers, this translates into measurable gains in machine uptime and process reliability. Predictable chip formation and secure cutting action Built around the FW4 chipbreaker and a Rhombus 55° platform, the insert supports controlled chip formation in typical steel cutting conditions. The geometry and chipbreaker design contribute to efficient evacuation of swarf, minimising rework risk and keeping the toolpath clear. A 7° clearance angle helps prevent rubbing at the flank while the 0.4 mm corner radius balances edge strength with the capability to achieve fine surface finishes. These features together mean fewer disturbances during medium to finishing operations and a smoother workflow at higher production volumes. Practical application guidance and compatibility The insert is intended for machining in material group P (steel) and is supplied in tolerance class M, offering a balance between precision and robustness for general turning tasks. The DCMT designation indicates compatibility with standard toolholders designed for that insert family; the insert’s form and chipbreaker allow flexible use in common roughing and finishing cycles where steel is the primary workpiece material. For implementation planning, specify the DCMT070204-FW4 WPP20G grade when ordering toolpacks for mixed steel production runs to standardise tooling performance across machines. Contact Metav Werkzeuge for application advice or to request matching toolholder recommendations — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss Walter Tools Tiger·tec Gold options and suitability for specific steel grades Technical Data Article number: DCMT070204-FW4-WPP20G-WALTER Designation: DCMT070204-FW4 WPP20G SKU: DCMT070204-FW4-WPP20G-WALTER Facts Clearance angle: 7° Corner radius: 0.4 mm Plate size: 07 Plate thickness: 02 Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP20G (coated carbide) Chipbreaker: FW4 Shape: Rhombus 55° Material application: Steel (P) Geometry execution: T Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The insert is suited for machining materials in group P, i.e. steel; the WPP20G grade and Tiger·tec Gold coating are optimised for the heat and chip formation typical of steel turning. What does the WPP20G designation mean? WPP20G denotes Walter Tools’ coated carbide grade within the Tiger·tec Gold family, combining wear resistance and versatility for steel applications. How does the FW4 chipbreaker help in production? The FW4 chipbreaker promotes controlled chip formation and evacuation, supporting uninterrupted cutting action and reduced risk of clogging in steel turning operations. Is the insert compatible with standard DCMT toolholders? The DCMT designation indicates a standard indexable insert geometry; toolholders designed for DCMT inserts are appropriate for this design. What surface quality can be expected with a 0.4 mm corner radius? A 0.4 mm corner radius offers a compromise between edge strength and surface finish, enabling fine finishes in medium to finishing cuts while maintaining robust edge life. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original factory-new goods of the manufacturer Walter Tools.
DCMT070204-FW4 WSM10S T Wendeplatten - Walter Tools
Take advantage of the combination of a proven Tiger·tec Silver coating and the WSM10S grade for stable chip control and extended tool life; the result is efficient machining of stainless steel and high-temperature alloys with predictable performance. Order the turning insert directly via Metav Werkzeuge or request tailored cutting recommendations from our consultants. DCMT070204-FW4, DCMT070204-FW4 WSM10S, WSM10S — Turning insert for stainless steel and heat-resistant superalloys | Walter Tools A DCMT070204-FW4 WSM10S turning insert designed for medium to heavy-duty turning of stainless steel and heat-resistant superalloys, offering reliable chip control and consistent edge life Tiger·tec Silver coated grade for extended tool life Designed for stainless steel and superalloys Rhombus 55° form with 0.4 mm corner radius FW4 chipbreaker for controlled chip formation Boosted productivity through coating and grade selection The combination of Tiger·tec Silver technology and the WSM10S grade delivers measurable gains in tool life and process reliability. The insert is a coated carbide solution developed to resist thermal load and edge wear when machining tough, heat-generating materials. In practice, this means fewer tool changes, longer productive cutting times and a more predictable maintenance rhythm on the shop floor. The protective coating reduces flank wear, enabling higher cutting parameters without sacrificing surface quality. Geometry that enhances cutting stability and surface finish The Rhombus 55° form and 7° relief angle create a stable cutting geometry that reduces vibration and improves contact conditions at the insert tip. A 0.4 mm corner radius supports robust engagement in medium and heavy cuts while maintaining a consistent surface finish; the radius balances edge strength and dimensional accuracy. The FW4 chipbreaker is engineered to produce short, controllable chips under the high temperatures typical of stainless steel and superalloys, simplifying chip evacuation and reducing the risk of built-up edge formation. Clear application range and machining recommendations This grade is primarily intended for machining materials classified as M (stainless steel) and S (heat-resistant superalloys and titanium). The insert performs best when used in stable setups and with appropriate coolant strategies for heat-sensitive alloys. Cutting data should be adapted to workpiece material and machine rigidity; the insert supports elevated cutting speeds thanks to its coating, but balanced feeds and depths of cut yield the best compromise between productivity and tool life for challenging alloys. Practical advantages for production environments In series production, the indexable design reduces tool-body inventory while enabling fast replacement and consistent repeatability. Compatibility with standard toolholders and straightforward seating make this insert suitable for diverse turning operations. Backed by Walter Tools engineering, the insert contributes to lower total machining cost per part through reduced downtime and predictable performance. Process planners benefit from the insert’s combination of edge stability and chip control when optimising cycle times. For efficient and reliable turning of stainless steel and superalloys, consider the Walter Tools DCMT070204-FW4 WSM10S insert — contact Metav Werkzeuge for individual cutting data and delivery options Technical Data Article number: DCMT070204-FW4-WSM10S-WALTER Article designation: DCMT070204-FW4 WSM10S Series: Tiger-tec Silver Grade: WSM10S Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 55° Plate size code: 07 Plate thickness code: 02 Chipbreaker: FW4 Tolerance class: M Special features Coated carbide (Tiger·tec Silver technology) Suitable for stainless steel (M) Suitable for heat-resistant superalloys and titanium (S) Designed for stable chip control and long edge life FAQ Which materials can be machined with this insert? The DCMT070204-FW4 WSM10S insert from Walter Tools is suitable for stainless steel (ISO group M) and for heat-resistant superalloys and titanium (ISO group S), as indicated by its WSM10S grade. What does the FW4 chipbreaker provide in practice? The FW4 chipbreaker on this turning insert generates short, reliably controlled chips under heavy thermal loading, improving chip evacuation and reducing the likelihood of built-up edge when machining stainless steel and superalloys. How does the Tiger·tec Silver coating benefit cutting performance? The Tiger·tec Silver coating enhances thermal resistance and reduces flank wear on the insert, allowing for higher cutting parameters and more consistent component quality over longer tool life. Is the insert suitable for interrupted cuts and heavy engagement? With its 0.4 mm corner radius and robust geometry, the insert is designed to handle heavier engagements and offers increased edge stability for interrupted or demanding turning operations. Can the DCMT070204-FW4 WSM10S be used in standard toolholders? Yes, the turning insert is an indexable format compatible with conventional toolholders that accept the DCMT geometry, enabling quick replacement and straightforward integration into existing tool systems. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen The Walter AG (brand: Walter Tools) is among the world's leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only. There is no association between our company and the named brands; the offered article is an original, factory-new product of the manufacturer.
DCMT070204-FW4 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of high thermal resistance, stable cutting-edge behaviour and optimised chip control to maintain steady production when machining stainless steel and high-temperature alloys; order directly via Metav Werkzeuge or consult our specialists for grade selection. DCMT070204-FW4 WSM20S – Turning insert, Tiger‑tec Silver coating, 7° clearance (Walter Tools) The DCMT070204-FW4 WSM20S is a rhombic 55° turning insert with a dedicated FW4 chipbreaker, designed for productive turning of stainless steel and heat‑resistant superalloys in demanding machining environments. Tiger·tec Silver coating for high heat resistance Optimised chipbreaker FW4 for secure chip control Rhombic 55° form with 0.4 mm corner radius Suitable for stainless steel and superalloys Consistent cutting-edge performance for demanding alloys The combination of WSM20S grade carbide and the Tiger‑tec Silver coating delivers improved heat resistance and a stable cutting edge, reducing the tendency to build up material during interrupted cuts. This grade is formulated for materials classified as M and S, specifically stainless steel and heat‑resistant superalloys, where thermal load and edge stress are high. By choosing this coated turning insert, process stability is increased and tool-change intervals are more predictable, which supports steady productivity in serial production. Geometry engineered for predictable surface finish The rhombic 55° geometry and a 0.4 mm corner radius provide a balance between edge strength and achievable surface quality. The 7° clearance reduces rubbing on the flank face, which helps to maintain dimensional accuracy and consistent part finish over longer cycles. For shops converting from general‑purpose grades, the defined geometry minimises the need for excessive feed reductions while maintaining process reliability. Secure chip control that supports cycle time reduction The FW4 chipbreaker is optimised for controlled chip formation in tough materials, guiding chips away from the cutting zone and reducing downtime caused by entanglement or recutting. Stable chip evacuation contributes to repeatable tool life and safer automated operation. In combination with the coated grade and robust edge, this insert supports higher cutting parameters where the machine and setup allow, offering a concrete route to improved throughput. Simple integration and selection advice for metalworking shops The insert’s designation and form fit standard toolholders for rhombic 55° carbide inserts, enabling straightforward integration into existing turning setups. For choice of cutting parameters, base feeds and speeds on material group, rigidity and coolant use; the coating and grade allow a bias towards higher thermal stability settings. If machining stainless steel or nickel‑based alloys is a recurring requirement, this insert offers a clear technical advantage in edge life and process security. Contact Metav Werkzeuge for tailored advice on integrating Walter Tools Tiger‑tec Silver inserts and selecting the correct grade and geometry for specific stainless steel applications Technical data Article number: DCMT070204-FW4-WSM20S-WALTER Designation: DCMT070204-FW4 WSM20S Series: Tiger‑tec Silver Grade: WSM20S Manufacturer: Walter Tools Execution: T Core dimensions Insert form: Rhombus 55° Clearance angle: 7° Corner radius: 0.4 mm Insert size: 07 Plate thickness: 02 Tolerance class: M Materials & special features Coating: Tiger‑tec Silver Chipbreaker: FW4 Applicable materials: stainless steel (M), heat‑resistant alloys and titanium (S) Substrate: coated carbide Series characteristics: optimised chip formation, stable cutting edge FAQ What materials is this insert suitable for? The DCMT070204-FW4 WSM20S insert is designed for stainless steel and heat‑resistant superalloys (material groups M and S), providing enhanced edge stability under high thermal load. How does the FW4 chipbreaker improve machining? The FW4 chipbreaker on the DCMT070204-FW4 WSM20S promotes controlled chip formation and evacuation, which reduces the risk of chip entanglement and supports more consistent cycle times. Which features help to prevent built‑up edge when turning stainless steel? The combination of the WSM20S grade and Tiger‑tec Silver coating improves heat resistance and reduces adhesion, helping to prevent built‑up edge during stainless steel turning. Is the insert compatible with standard rhombic 55° toolholders? Yes, the rhombic 55° form and standard dimensions of the DCMT070204-FW4 WSM20S allow direct fitting into conventional holders designed for that geometry. What does the tolerance class M indicate for this insert? Tolerance class M denotes the machining accuracy and manufacturing tolerances of the insert; for the DCMT070204-FW4 WSM20S this supports reliable, repeatable positioning in the toolholder. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no connection between our company and the named brands. The offered article is an original factory‑new product of the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com