DCGW070204TS-2 WBK20 Wendeplatten - Walter Tools
Combining the CBN WBK20 cutting grade with a rhombic 55° geometry and a precise 0.4 mm corner radius yields a wear‑resistant insert tailored for demanding, hardened turning tasks; order the DCGW070204TS-2 WBK20 via Metav Werkzeuge or consult their technical advisers for application guidance. DCGW070204TS-2 WBK20 — Indexable Turning Insert (Rhombic 55°, 7° clearance) by Walter Tools DCGW070204TS-2 WBK20 is an indexable turning insert designed for high‑performance machining of hard and abrasive materials CBN grade WBK20 for hard, wear‑resistant machining Rhombic 55° insert form for versatile turning 7° clearance angle for stable cutting engagement 0.4 mm corner radius for defined edge strength High‑performance CBN grade for hardened components The CBN‑based WBK20 grade is engineered for consistently stable cutting when machining hardened steels and other abrasive workpiece materials. The key advantage lies in the insert's material: cubic boron nitride delivers exceptional hardness and thermal stability, which translates into longer service life and reduced tool change frequency. This results in fewer interruptions in production and improved cost efficiency per component while maintaining dimensional consistency and surface quality. Geometry that enhances process reliability The rhombic 55° shape combined with a 7° clearance angle offers a balance between general‑purpose versatility and secure engagement in the cutting zone. The geometry allows for controlled chip formation and reliable approach to shoulders or interrupted cuts, while the 0.4 mm corner radius increases edge robustness without compromising profile accuracy. Such design choices support repeatable results and minimise the risk of premature edge failure during medium to heavy interrupted turning. Practical benefits for workshop productivity As an indexable insert, this item simplifies tool management: a defined insert geometry and tolerance class G make replacement and set‑up predictable, aiding cycle time reduction and improving process planning. The presence of a chipbreaker (position 2) assists in chip control under typical turning conditions, supporting stable machining and safe evacuation of chips. For operational planning, the grade’s catalogue‑dependent material designation advises checking the product matrix to confirm optimal workpiece materials and cutting data. Guidance for selection and integration into existing tooling Selection should be based on the workpiece material and process demands; WBK20 is primarily aimed at hard, high‑wear applications and may also suit certain cast or superalloy tasks depending on the specific product matrix. Confirm that the insert designation DCGW070204TS‑2 matches the toolholder pocket and clamping method in use. If uncertainty arises about fitment or application parameters, the product matrix and Metav Werkzeuge’s technical advisors provide targeted recommendations to align cutting strategy with component requirements. Contact Metav Werkzeuge for tailored application advice on the Walter Tools DCGW070204TS-2 WBK20 insert — request the product matrix or discuss holder compatibility at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: DCGW070204TS-2-WBK20-WALTER ISO designation: DCGW070204TS-2 WBK20 Type: Drehwendeschneidplatte / Indexable turning insert Manufacturer: Walter Tools Insert form: Rhombus 55° Grade: WBK20 Tolerance class: G Facts Clearance angle: 7° Corner radius: 0.4 mm Insert size: 07 Thickness code: 02 Chipbreaker: 2 Special features CBN cutting material (high hardness, thermal stability) Series: Walter Schneidstoffsorte - Serie offen Material designation: catalogue‑dependent Intended for hard and strongly abrasive tasks (check product matrix) FAQ Is this insert suitable for hardened steels? The DCGW070204TS-2 WBK20 from Walter Tools uses a CBN‑based grade intended primarily for hardened steels; suitability should be verified against the product matrix for the specific component material. What does the WBK20 grade indicate? WBK20 denotes Walter Tools’ CBN cutting grade, developed for wear resistance and stable performance in high‑hardness turning applications. Which geometry and edge specifications does the insert offer? The insert features a rhombic 55° form with a 7° clearance angle and a 0.4 mm corner radius, designed to enhance edge strength and stable engagement. Can this insert be used with standard DCGW tool holders? The designation DCGW070204TS-2 follows standard insert nomenclature; the insert fits corresponding DCGW pockets — confirm holder compatibility with the toolholder manufacturer and the product matrix. Does the insert include a chipbreaker? Yes, the insert is provided with chipbreaker type 2 to assist chip control during turning operations. Protected trademarks and trade names remain the property of their respective owners. Brand names and trademarks are cited for explanatory purposes only and do not imply any affiliation with Metav Werkzeuge. The offered item is original, factory‑new goods of the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCGW070208TM-2 WBH20 WBH20 Wendeplatten - Walter Tools
Take advantage of the CBN cutting material and the rhombic geometry to secure high wear resistance and consistent edge life for hard turning operations; order the insert directly via Metav Werkzeuge or consult their advisors for application-specific recommendations. DCGW070208TM-2 WBH20 indexable turning insert — Walter Tools — CBN grade for hard turning, rhombic 55°, 7° clearance DCGW070208TM-2 WBH20 is an indexable turning insert designed for hard machining tasks; its CBN-based grade provides the abrasion resistance required for hardened steels while the rhombic geometry supports versatile cutting strategies CBN grade WBH20 for hard turning Rhombic 55° geometry for versatile cutting 7° clearance angle for stable cutting 0.8 mm corner radius for predictable edges High wear resistance engineered for hard machining The insert’s CBN composition and WBH20 grade deliver significantly improved abrasion resistance for hard turning of hardened steels. Designed for operations where elevated cutting forces and heat stress are present, this cutting material maintains a consistent edge over extended tool life, reducing the frequency of index changes and supporting predictable production cycles. The combination of material and geometry is particularly effective for components specified within the ISO group for hardened steels. Geometry that stabilises cutting and chip control The rhombic 55° outline paired with a 7° clearance ensures a reliable cutting angle that balances edge strength and accessibility in tight radii. The 0.8 mm corner radius contributes to a robust cutting edge that resists chipping during interrupted cuts. Together with the designated chipbreaker type, the geometry enables repeatable chip formation and stable cutting forces, which translates into fewer process interruptions and improved surface quality on hard workpieces. Process security and predictable productivity Belonging to the Walter CBN / Hartstoff series, this insert emphasises process security for demanding applications. The CBN composition is optimised for wear resistance in hard materials, supporting steady results across batches and lowering unexpected tool-wear variability. By using this grade, shops achieve a longer effective cutting life under comparable conditions, which contributes to reduced machine downtime and better overall throughput in hard-machining cells. Selection and integration guidance for production use As an indexable turning insert with the DCGW geometry, the component is intended for holders accommodating rhombic 55° inserts and follows common industrial designation practices. Its format and codes (size and thickness) permit straightforward identification during tool planning, while the specification of the CBN grade helps to map the insert to the correct workpiece material class. For precise setup parameters and to ensure optimal performance in a given machine or holder, technical consultation is recommended. Contact Metav Werkzeuge for tailored selection and procurement of the Walter Tools DCGW070208TM-2 WBH20 CBN turning insert — email info@metav-werkzeuge.com or call +49 2822 7131930 for application-specific advice and availability Technical data Article number / SKU: DCGW070208TM-2-WBH20-WALTER Product type: Indexable turning insert Designation: DCGW070208TM-2 WBH20 Manufacturer: Walter Tools Series: Walter CBN / Hartstoff Grade: WBH20 Core specifications Clearance angle: 7° Corner radius: 0.8 mm Plate form: Rhombus 55° Size code: 07 Thickness code: 02 Chipbreaker: 2 Tolerance class: G Features & applications Suitable for hardened steels (H) Suitable for pre-hardened steel applications CBN cutting material for high abrasion resistance Designed for hard machining / hard turning Execution: W FAQ What workpiece materials is this insert suitable for? The DCGW070208TM-2 WBH20 is specified for hardened steels (ISO group H) and is also applicable for pre-hardened steel operations thanks to its CBN-based WBH20 grade. What advantages does the WBH20 CBN grade offer? WBH20 provides high abrasion resistance and a consistent edge under the thermal and mechanical loads typical of hard turning, which helps to maintain dimensional consistency and surface quality. Which geometry benefits can be expected from the rhombic 55° shape? The rhombic 55° form offers flexible cutting orientations and, combined with the 7° clearance, supports stable cutting conditions and access to various profile geometries. How does the insert support chip control? Chip control is achieved through the designated chipbreaker and the insert geometry; the combination in the DCGW070208TM-2 WBH20 produces predictable chips and stable forces during hard machining. Is this insert suitable for interrupted cuts and tough surfaces? Yes; the 0.8 mm corner radius and the CBN composition of the WBH20 grade are selected to resist chipping and edge degradation in demanding interrupted or high-stress cutting scenarios. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered item is original, factory-new merchandise of the manufacturer.
DCGW070208TS-2 WBK20 Wendeplatten - Walter Tools
Take advantage of the combination of a CBN cutting grade for hard, abrasive tasks and a compact rhombic geometry that supports stable cutting forces; this results in reliable edge life and process security in production turning. Order the insert directly via Metav Werkzeuge or consult our specialists for material-specific advice. DCGW070208TS-2 WBK20 – Turning indexable insert, CBN grade, Walter Tools The DCGW070208TS-2 WBK20 is a CBN turning insert engineered for productive machining of hardened and highly abrasive materials, suited to demanding finishing and light roughing operations. CBN grade WBK20 for hardened materials Rhombic insert 55° for versatile turning 7° clearance angle for stable cutting 0.8 mm corner radius for strong cutting edge Stable performance where hardness matters The CBN composition of this insert delivers consistent wear resistance on hardened steels, extending tool life under high contact stresses. The rhombic 55° geometry reduces cutting forces in interrupted cuts and supports versatile turning strategies, while the 7° clearance angle helps maintain a defined cutting edge geometry. These characteristics translate into fewer tool changes and predictable cycle times, improving overall production throughput and repeatability. Predictable edge strength and surface quality With a 0.8 mm corner radius and an optimised chipbreaker 2, the insert balances edge robustness with controlled chip formation. This combination promotes stable surface finish and reduces the risk of edge chipping in demanding cuts. The modest plate thickness and compact format contribute to secure clamping and reduced vibration, which benefits both surface integrity and tool life in serial machining. Application guidance and process security This CBN grade is described as suitable for hard and highly abrasive machining tasks; verify material compatibility against the product matrix before selection. The insert is particularly effective for finishing operations on thermally hardened components where abrasion and high contact pressure shorten the life of conventional carbide grades. When paired with appropriate cutting parameters, the insert supports stable, reproducible results and fewer interruptions in the machining cycle. Practical advantages for workshop integration Compact geometry and standard designation simplify inventory management and toolholders selection. The clear ISO-style designation aids ordering and ensures the correct grade is specified for high-demand applications. For operations seeking improved uptime and consistent part quality, this insert provides a technical route to enhanced process reliability without complex handling requirements. For application-specific recommendations or to source Walter Tools inserts, contact Metav Werkzeuge for machining advice and availability via eMail: info@metav-werkzeuge.com or phone: +49 2822 7131930 — our team will assist with suitability checks and ordering. Technical data Article number: DCGW070208TS-2-WBK20-WALTER Designation: DCGW070208TS-2 WBK20 Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Facts Geometry: Rhombus 55° Clearance angle: 7° Corner radius: 0.8 mm Plate size: 07 Plate thickness: 02 Chipbreaker: 2 Tolerance class: G Materials / Special features Grade: CBN (WBK20) Material information: Katalogabhängig Intended application: hard and highly abrasive materials; check product matrix for exact suitability Series information: Walter Schneidstoffsorte - Serie offen FAQ What materials is this insert designed for? The DCGW070208TS-2 WBK20 insert is a CBN grade intended primarily for hardened and highly abrasive materials; suitability should be confirmed against the product matrix for specific alloys. Can this insert be used for finishing hardened steel components? Yes, the WBK20 grade and the rhombic 55° geometry support finishing operations on hardened steels, providing stable cutting and consistent surface quality. How does the 0.8 mm corner radius affect performance? A 0.8 mm corner radius increases edge strength and reduces the likelihood of chipping, which is beneficial for interrupted or heavy finishing cuts. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trademarks are stated for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original, brand-new goods of the manufacturer Walter Tools.
DCGW11T302FS-1 WDN10 W - Wendeplatten - Walter Tools
Taking advantage of the insert's PKD composition and precise geometry delivers extended tool life and consistent surface quality in the machining of abrasive non‑ferrous materials; order this high‑performance insert via Metav Werkzeuge or request specification advice from the consultants at Metav Werkzeuge. DCGW11T302FS-1 WDN10 – PKD turning insert, Rhombus 55° by Walter Tools The DCGW11T302FS-1 WDN10 is a precision indexable turning insert designed for demanding non‑ferrous and abrasive material applications, offering a durable PKD grade and compact Rhombus 55° form for reliable chip control and repeatable results. PKD grade WDN10 for abrasive non‑ferrous materials Rhombus 55° geometry for versatile turning operations 0.2 mm corner radius for refined surface finishes 7° rake angle for consistent chip formation Proven wear resistance for abrasive applications The insert’s WDN10 grade is a polykristalliner Diamant (PKD) material engineered for outstanding abrasion resistance, which translates into longer intervals between index changes and reduced downtime. In practical terms, the hardness and wear behaviour of the diamond layer maintain cutting edge integrity when working with abrasive, non‑ferrous alloys and composite materials; this stability supports predictable tool life and helps to keep production schedules steady. Selection should be validated against the product matrix to confirm optimal performance for specific workpiece materials. Geometry that improves surface quality and repeatability A compact Rhombus 55° form combined with a 0.2 mm corner radius and a 7° free angle creates a balance between strength and finesse: the geometry supports secure seating in the toolholder while enabling fine surface finishes and close dimensional tolerances. The T3 plate thickness contributes to adequate stiffness for medium finishing passes, and the defined chipbreaker 1 assists controlled chip formation, reducing rework. These engineered dimensions offer a practical route to consistent part quality in series production. Process efficiency and machining security Using a PKD insert from a reputable maker such as Walter Tools reduces the frequency of tool changes in high‑volume operations, which supports throughput improvements and lowers indirect production costs. The robust cutting edge of the diamond grade preserves dimensional stability across long runs, contributing to process security and reproducible results. For planners and process engineers, the insert’s characteristics enable straightforward integration into automated turning cycles while maintaining consistent end‑product quality. Specification support and application guidance Selection of the correct PKD grade and insert geometry can significantly influence machining outcomes; consultation and verification against the manufacturer’s product matrix are recommended to match the insert to the workpiece material and machining strategy. Technical advice and material‑specific recommendations are available through Metav Werkzeuge, offering specification support and machining parameter guidance to ensure the insert is used to its full potential in the intended application. Discuss material suitability and machining parameters with Metav Werkzeuge to ensure optimal use of this Walter Tools PKD turning insert; contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical data SKU: DCGW11T302FS-1-WDN10-WALTER Designation: DCGW11T302FS-1 WDN10 Type: Turning indexable insert Manufacturer: Walter Tools Facts Insert size: 11 Shape: Rhombus 55° Corner radius: 0.2 mm Rake angle: 7° Thickness: T3 Chipbreaker: 1 Tolerance class: G Materials & features Grade: WDN10 (PKD) Series: Walter Schneidstoffsorte - Serie offen Execution: W Material: catalogue dependent Intended use: PKD mainly for non‑ferrous and abrasive non‑ferrous materials; check product matrix for confirmation FAQ What materials is this PKD grade suitable for? The WDN10 PKD grade is primarily intended for non‑ferrous and abrasive non‑ferrous materials; suitability should be confirmed via the manufacturer’s product matrix before application. How does the 0.2 mm corner radius affect surface finish? A 0.2 mm corner radius provides a fine compromise between edge strength and the ability to achieve refined surface finishes, making it suitable for finishing and semi‑finishing passes. Is this insert appropriate for heavy roughing operations? The combination of Rhombus 55° geometry and T3 thickness favours finishing and medium cutting conditions; for heavy roughing, a more robust geometry or a thicker plate may be preferable. What does chipbreaker 1 indicate? Chipbreaker 1 denotes a geometry designed for controlled chip formation in the specified material range, supporting consistent evacuation and reduced risk of built‑up edge in non‑ferrous machining. Can the insert grade be used on steel or hardened materials? As a PKD grade, WDN10 is optimised for non‑ferrous and abrasive non‑ferrous workpieces; use on ferrous or hardened steels is generally not recommended and requires verification against the product matrix. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (marketed as Walter Tools) is a leading manufacturer of precision tools for metalworking and forms part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. The mentioned brand names are used solely for explanation. There is no connection implied between Metav Werkzeuge and the cited manufacturers. The offered article is original, brand‑new merchandise from the manufacturer.
DCGW11T302TM-2 WBH20 Wendeplatten - Walter Tools
Combining the CBN grade WBH20 for high wear resistance, a Rhombic 55° geometry and a 7° relief angle, this insert delivers stable cutting and consistent performance in hard turning operations; order the DCGW11T302TM-2 WBH20 indexable turning insert via Metav Werkzeuge or consult the technical team for specific applications. DCGW11T302TM-2 WBH20 – Indexable turning insert for hard turning (Walter Tools) The DCGW11T302TM-2 WBH20 is an indexable turning insert engineered for hard-material turning, offering a robust CBN grade and geometry suited to precision finishing and wear-critical operations. CBN grade WBH20 for hard turning Rhombic 55° geometry for stable cuts 7° relief angle for reduced cutting forces 0.2 mm corner radius for fine surface finish Consistent performance for hardened components The combination of a CBN cutting material and the WBH20 grade provides exceptionally high wear resistance for machining hardened steels and comparable superalloys. This ensures longer effective life under elevated cutting temperatures and abrasive conditions, reducing tool changes and improving process uptime. The insert’s geometry is configured to maintain stable cutting even when tolerances and surface quality are critical, making it a reliable choice for series production of hardened shafts, bearing seats and similar components. Geometry that improves chip control and surface quality A Rhombic 55° shape paired with a defined chipbreaker and a 0.2 mm corner radius minimises vibration and supports consistent chip flow. The moderate radius helps to deliver a fine surface without sacrificing edge strength, while the chipbreaker setting (chipbreaker 2) is tuned for controlled segmentation under the higher cutting loads typical of hard turning. These attributes translate into reduced rework and a predictable finish, which is particularly valuable where downstream processes demand consistent part quality. CBN technology tailored for hard machining The WBH20 grade is part of the Walter CBN series and is specified for abrasive, high-hardness applications in accordance with the material group for hardened steels (ISO 513 — group H). As a superhard material, CBN offers thermal and wear resistance far beyond conventional carbides, allowing higher cutting speeds and stable performance when machining pre-hardened and through-hardened components. The indexable concept simplifies tool management: inserts can be indexed or replaced without regrinding, supporting efficient workshop routines and reliable cycle times. For application advice, grade selection guidance or to request availability of the Walter Tools DCGW11T302TM-2 WBH20 indexable turning insert, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: DCGW11T302TM-2-WBH20-WALTER Designation: DCGW11T302TM-2 WBH20 Manufacturer: Walter Tools Facts Insert form: Rhombic 55° Size: 11 Thickness: T3 Corner radius: 0.2 mm Relief angle: 7° Chipbreaker: 2 Tolerance class: G Grade: WBH20 Special features Series: Walter CBN / Hartstoff Suitable for: hardened steels (ISO 513 — group H) Application: hard turning, high-wear operations Execution: W FAQ What materials is this insert suitable for? The DCGW11T302TM-2 WBH20 insert is designed primarily for hardened steels (ISO 513 group H) and similar hard materials where CBN grades provide superior wear resistance. How does the WBH20 grade differ from carbide inserts? WBH20 is a CBN grade that offers significantly higher thermal and abrasive wear resistance than conventional carbide, enabling more stable performance and longer life in hard machining. Which toolholders accept this insert geometry? This rhombic 55° insert is compatible with standard turning toolholders designed for DCGW-style inserts; confirm the toolholder pocket matches the DCGW11T302TM-2 designation for secure clamping. Is the 0.2 mm corner radius suitable for finishing operations? Yes, the 0.2 mm corner radius balances edge strength with the ability to produce fine surface finishes, making it appropriate for semi-finishing to finishing passes in hardened components. Can this insert be used for interrupted cuts? While CBN inserts like WBH20 excel in continuous, high-wear applications, suitability for interrupted cuts depends on the specific workpiece and machining parameters; evaluation on the intended setup is recommended. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the named brands. The offered item is original, brand-new goods of the manufacturer Walter Tools.
DCGW11T302TM-2 WBH30 Wendeplatten - Walter Tools
Optimise productivity in hard-turning operations with the CBN-grade WBH30 and a compact rhombic geometry that delivers stable edge life and reliable chip control; order the insert directly via Metav Werkzeuge or request technical advice from their consultants. DCGW11T302TM-2 WBH30 — Walter Tools turning insert, CBN grade for hardened steels The DCGW11T302TM-2 WBH30 is a turning insert engineered for hard machining of hardened steels, combining a CBN cutting material and a rhombic 55° shape for consistent wear resistance. CBN grade WBH30 for hard materials Rhombic 55° geometry for versatility 7° relief angle for stable cutting action 0.2 mm corner radius for fine surface finish High-performance cutting for hardened materials The WBH30 grade is a CBN (cubic boron nitride) compound developed specifically for demanding hard-turning tasks. As a superabrasive, CBN resists thermal and abrasive wear far better than conventional carbide, which translates into longer service life and fewer insert changes in series production. This characteristic provides a measurable improvement in process economy and reduces unplanned downtime during machining of hardened steels. The material pairing and edge stability make this insert suited for applications where consistent dimensional accuracy and repeatability are required. Geometry that balances strength and accessibility The rhombic 55° form offers a combination of accessibility to external contours and favourable cutting forces, while the 7° relief creates a positive rake that helps maintain a stable cutting edge under the elevated forces of hard machining. The small 0.2 mm corner radius supports fine finishing passes and helps achieve improved surface integrity without sacrificing edge strength. Together, these geometry choices permit both roughing and light finishing operations with a single indexable solution, simplifying tool set-ups and reducing tooling variants in the tool crib. Controlled chip formation and predictable tool life Equipped with chipbreaker 2, the insert promotes predictable chip control during interrupted cuts and continuous hard-turning cycles. Controlled chip formation limits the risk of re-cutting and cradle-falls while stabilising cutting forces, which in turn supports repeatable component quality. The insert’s CBN composition contributes to a predictable wear pattern that is easier to schedule and monitor, enabling process engineers to plan insert changes on defined production intervals rather than reactive interventions. Application focus and process integration Designed within the Walter CBN / Hartstoff series, this insert is intended for hard machining of through-hardened or pre-hardened steels and other highly abrasive materials where conventional grades would wear prematurely. Its compatibility with hardened materials (designation H) means that the component groups defined under ISO 513 for hard steels are directly addressable with this solution. Selection of cutting parameters and stable clamping systems will further enhance the insert’s performance and support consistent cycle times in production environments. For high-precision hard-turning tasks, request a quote for the Walter Tools DCGW11T302TM-2 WBH30 from Metav Werkzeuge or consult their technical specialists for optimal cutting data and availability. Technical data SKU: DCGW11T302TM-2-WBH30-WALTER Article designation: DCGW11T302TM-2 WBH30 Manufacturer: Walter Tools Product type: Drehwendeschneidplatte (turning insert) Series: Walter CBN / Hartstoff Facts Relief angle: 7° Corner radius: 0.2 mm Insert size: 11 mm Thickness: T3 Plate form: Rhombic 55° Chipbreaker: 2 Tolerance class: G Special features CBN cutting material (WBH30) Suitable for hardened steels Series for hard machining Stable edge life and wear resistance Application: hard turning FAQ Is this insert suitable for through-hardened steels? Yes. The DCGW11T302TM-2 WBH30 uses a CBN grade designed specifically for hardened materials and is suitable for machining through-hardened and pre-hardened steels. What advantages does the WBH30 grade provide over carbide? The WBH30 CBN grade provides superior resistance to abrasive and thermal wear compared with carbide, resulting in longer tool life and more consistent part dimensions during hard machining. Can this insert handle interrupted cuts and roughing? The combination of the rhombic geometry, 7° relief, and chipbreaker 2 supports controlled chip formation and stable cutting forces, making it appropriate for many interrupted-cut and roughing scenarios in hardened materials. How does the 0.2 mm corner radius affect the finish? A 0.2 mm corner radius helps achieve finer surface finishes while maintaining sufficient edge strength for typical finishing and semi-finishing passes in hard turning operations. Is this insert part of a dedicated product series for hard machining? Yes. The insert belongs to the Walter CBN / Hartstoff series and is optimised for hard machining tasks where wear resistance and process stability are priorities. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand presentation: Walter Tools) with headquarters in Tübingen is a leading manufacturer of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for clarification and identification purposes. There is no affiliation between our company and the mentioned brands; the offered item is an original, factory-new product of the respective manufacturer.
DCGW11T302TS-2 WBH10 Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, stable cutting performance and a geometry optimised for finishing hard components; order the insert directly via Metav Werkzeuge or consult the team for application-specific recommendations. DCGW11T302TS-2 WBH10 turning insert (CBN, Rhombus 55°) – Walter Tools The DCGW11T302TS-2 WBH10 is a CBN-grade turning insert designed for hard machining, optimised for finishing and semi-finishing of hardened Stahl components. CBN grade for hard, abrasive materials Rhombus 55° geometry for versatile turning 0.2 mm corner radius for precise finishing T3 thickness for edge stability Consistent hard‑machining performance for long runs The WBH10 grade is a CBN cutting material developed for demanding, high‑wear operations on gehärtete Stähle and similar hard materials. Its microstructure provides a high resistance to abrasive wear, which translates into longer tool life and fewer indexings during production. For shops aiming to maintain cycle-time stability on sequential hard turning operations, the combination of a CBN grade with a robust geometry reduces unplanned tool changes and supports a predictable machining window. This results in improved uptime and a measurable contribution to process efficiency. Geometry tuned for surface quality and dimensional control The Rhombus 55° form with a 0.2 mm corner radius prioritises controlled chip flow and consistent contact conditions at the cutting edge. The insert’s geometry contributes to improved surface finishes on hardened components while keeping cutting forces within expected ranges for insert-based turning. The moderate corner radius permits fine finishing passes without compromising edge strength, so fewer corrective grinding or rework steps are required. Where tight tolerances matter, the predictable behaviour of the geometry supports repeatable results in serial production. Stable edge life and integration into standard toolholders With a T3 plate thickness and tolerance class G, the insert delivers mechanical stability under the elevated stresses of hard‑material cutting. The series designation, Walter CBN / Hartstoff, indicates optimisation for hard turning tasks and a broad application window within hardened and pre‑hardened Stahl grades. Compatibility with common clamping systems and straightforward indexability reduces set-up time, and the stable cutting edge contributes to consistent dimensional accuracy over consecutive parts. The insert is suitable for both finishing and semi‑finishing where tool life and surface integrity are decisive. For application advice or to secure timely supply of Walter Tools CBN inserts, contact Metav Werkzeuge for tailored recommendations and order coordination. Technical data Article number: DCGW11T302TS-2-WBH10-WALTER Insert designation: DCGW11T302TS-2 WBH10 Manufacturer: Walter Tools Product type: Turning insert Facts Plate form: Rhombus 55° Plate size: 11 Plate thickness: T3 Free angle: 7° Corner radius: 0.2 mm Chipbreaker: 2 Tolerance class: G Special features Series: Walter CBN / Hartstoff Grade: WBH10 (CBN) Material code: H (for hardened Stahl) Applicable to: Stahl, pre‑hardened Stahl Intended use: hard machining, finishing of hardened components FAQ What materials is this insert intended for? The insert is designed for hard machining; the WBH10 CBN grade is optimised for gehärtete Stähle and pre‑hardened Stahl applications. How does the Rhombus 55° form affect turning operations? Rhombus 55° geometry offers versatility for a range of turning tasks, giving a balance of access and edge strength that supports finishing and semi‑finishing on hard materials. What edge radius is recommended for fine finishing? This insert features a 0.2 mm corner radius which is suitable for precise finishing passes while maintaining edge robustness. Is the insert compatible with standard toolholders? The DCGW11T302TS‑2 insert conforms to common indexable insert dimensions and mounting practices, enabling integration into standard turning toolholders. What benefits does the WBH10 grade bring to serial production? WBH10 provides high wear resistance and stable cutting performance, which reduces the need for frequent indexing and supports consistent surface quality in serial hard turning. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand appearance: Walter Tools) is part of the Sandvik Group and is one of the world’s leading manufacturers of precision cutting tools for metalworking. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected designations are mentioned exclusively for explanatory purposes. There is no affiliation implied between Metav Werkzeuge and the manufacturers; the offered article is an original, factory‑new product of the stated manufacturer.
DCGW11T302TS-2 WBH10C Wendeplatten - Walter Tools
Take advantage of the high wear resistance of the CBN grade and the precise 0.2 mm corner radius for consistent finishing in hard turning applications; order through Metav Werkzeuge or request advice from our consultants to ensure the insert meets the production requirements. DCGW11T302TS-2 WBH10C – Indexable turning insert for hard machining, CBN grade, Walter Tools A DCGW11T302TS-2 WBH10C indexable turning insert designed for demanding hard‑machining tasks on hardened steels and similar high‑wear materials CBN grade WBH10C for hard machining Rhombic 55° shape for versatile turning 7° clearance angle for stable cutting 0.2 mm corner radius for precision finishes Stable wear performance for hard machining operations The combination of the WBH10C CBN grade and the insert’s geometry provides a reliable solution for high‑hardness components. The CBN cutting material is engineered for hardened steels, offering excellent resistance to abrasive wear and maintaining a steadier cutting edge under high surface pressures. In practice, this means longer intervals between index changes and more consistent component tolerances; production runs on tempered shafts or hard bushes benefit from fewer interruptions and a predictable tool life. The insert’s suitability for the H material group is explicitly indicated, clarifying applications for heat‑treated and high‑strength steels. Geometry that delivers repeatable surface quality and dimensional control The Rhombic 55° form and a 0.2 mm corner radius support precise profile control and fine surface finishes in turning operations. The rhombic angle offers a balance between approach angle and strength, enabling controlled radial engagement and good chip flow, while the small corner radius supports tight tolerances on shoulders and small‑radius features. The 7° clearance angle reduces flank contact and helps preserve surface integrity over extended cycles. Together these geometric characteristics lower the risk of chatter and minimise rework, which is particularly valuable when processing hardened parts where corrective machining is costly. Process security and practical advantages at the shop floor This insert is produced in the Walter CBN / Hartstoff series to ensure consistent manufacturing quality and traceable performance. The chipbreaker 2 design facilitates predictable chip segmentation when turning difficult materials, aiding coolant penetration and chip evacuation. The insert thickness (T3) and size (11) facilitate compatibility with common toolholder systems that accept the DCGW form, streamlining tool changeovers. Choosing this insert supports a rational approach to process planning: fewer tool changes, stable cutting conditions and reproducible surface finishes translate into measurable productivity gains in hard‑turning applications. For technical guidance, availability and tailored recommendations for Walter Tools CBN inserts, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our specialists will advise on the optimal setup and supply options. Technical data Article number: DCGW11T302TS-2-WBH10C-WALTER Label: Drehwendeschneidplatte DCGW11T302TS-2 WBH10C Walter Tools Manufacturer: Walter Tools Product type: Indexable turning insert Facts Clearance angle: 7° Corner radius: 0.2 mm Insert size: 11 Thickness: T3 Shape: Rhombus 55° Special features Grade: WBH10C Series: Walter CBN / Hartstoff Suitable for: hardened steels (H) Chipbreaker: 2 Tolerance class: G Execution: W FAQ What materials is this insert intended to machine? This insert is designed primarily for hardened steels (H); the WBH10C CBN grade is optimised for hard‑machining tasks where wear resistance and edge stability are critical. How does the 0.2 mm corner radius affect finish and tolerance? A 0.2 mm corner radius helps produce a fine surface finish and supports dimensional control on small radii and shoulder features when using the DCGW11T302TS‑2 WBH10C insert. Is the DCGW11T302TS‑2 compatible with standard DCGW toolholders? Yes, the insert’s Rhombus 55° form and size designation correspond to common DCGW‑style toolholder systems; confirm holder compatibility with the tool‑holder supplier where necessary. What benefit does the WBH10C CBN grade offer over conventional carbide? The WBH10C CBN grade offers superior wear resistance in high‑hardness materials, reducing flank wear and prolonging effective cutting life compared with standard carbide grades in hard‑turning operations. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCGW11T302TS-2 WBH20C Wendeplatten - Walter Tools
Take advantage of the high wear resistance and precise geometry to improve hard-turning productivity while reducing rework; the CBN-coated grade ensures stable cutting in hardened materials and the 0.2 mm nose radius supports consistent surface quality. Order the insert via Metav Werkzeuge or consult our specialists for application advice and availability. DCGW11T302TS-2 WBH20C indexable turning insert – Walter Tools, CBN grade for hardened steel The DCGW11T302TS-2 WBH20C is a CBN-coated indexable insert designed for hard turning and finishing of hardened steels within demanding production environments. Coated CBN for hard machining Rhombic 55° geometry for secure engagement 0.2 mm nose radius for fine surface finish Optimised performance for hardened components The insert delivers reliable wear resistance thanks to its coated CBN grade, which is specifically engineered for hardened steels and other high-wear applications. CBN, as a superabrasive, maintains cutting edge stability at high contact stresses and reduces flank wear compared with conventional carbides; this translates into longer tool life and fewer tool changes, improving process efficiency. The 55° rhombic geometry supports robust engagement and makes the component easier to programme for common turning operations, while the modest clearance angle assists consistent chip flow during hard machining. Precision geometry that reduces rework and cycle time A carefully selected 0.2 mm corner radius and the insert’s precise shape minimise vibration and help achieve repeatable surface quality, which reduces downstream finishing and inspection time. The combination of thin T3 thickness and the defined chipbreaker layout ensures predictable cutting behaviour in interrupted or continuous cuts, helping to protect the workpiece and the toolholder. These geometric characteristics support both rough turning under high forces and finishing passes where dimensional accuracy and surface integrity are required. Application suitability and practical benefits This indexable insert is intended for the hard machining of steels classified under ISO group H, including pre-hardened or through-hardened components. The WBH20C grade is optimised for stable chip formation and reliable performance in demanding alloys and heat-treated parts. For operations that demand consistent reproducibility and reduced downtime, the insert helps lower process costs through extended life and fewer interruptions. If toolholder compatibility is a concern, confirm clamping and seat dimensions with standard DCGW toolholder types to ensure correct fitment. For tailored recommendations on using the Walter Tools DCGW11T302TS-2 WBH20C in specific applications, contact Metav Werkzeuge for technical consultancy and stock information: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: DCGW11T302TS-2-WBH20C-WALTER Model designation: DCGW11T302TS-2 WBH20C Product type: indexable turning insert (Drehwendeschneidplatte) Manufacturer: Walter Tools Series: Walter CBN / Hartstoff Grade: WBH20C Key measurements Clearance angle: 7° Corner radius: 0.2 mm Plate size: 11 Thickness: T3 Chipbreaker: 2 Plate form: Rhombic 55° Tolerance class: G Execution: W Materials & features Coating / cutting material: coated CBN Suitable for hardened steels (ISO group H) Suitable for pre-hardened steel applications Designed for hard machining and finishing Stable cutting edge and controlled chip formation Series and application: Walter CBN / Hartstoff FAQ What materials is this insert suitable for? The DCGW11T302TS-2 WBH20C is formulated for hardened steels (ISO group H) and is suitable for pre-hardened components and challenging hard-turning tasks. How does the CBN grade affect tool life? Coated CBN provides superior wear resistance in hard materials, extending tool life and enabling longer uninterrupted production runs with consistent performance. Is this insert appropriate for finishing passes? Yes, the 0.2 mm corner radius and precise geometry make the insert well suited to finishing operations where surface quality and dimensional control are required. Which insert geometry does DCGW indicate? The DCGW form denotes a rhombic 55° insert profile suitable for a variety of turning approaches; the specified geometry offers a good balance between strength and accessibility. Can this insert be used in interrupted cuts? The insert’s robust grade and chipbreaker design support interrupted cutting, but recommended cutting data and holder rigidity should be checked to match the specific job. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned for clarification only. There is no affiliation between our company and the named brands. The item offered is an original, factory-new product from the manufacturer.
DCGW11T304EM-2 WBS10 WBS10 Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, stable chip control and precise geometry for consistent turning of hardened components; order the insert directly via Metav Werkzeuge or contact the consultants for application guidance. DCGW11T304EM-2 WBS10 Walter Tools — Indexable turning insert, CBN grade, Rhombic 55° The DCGW11T304EM-2 WBS10 is an indexable turning insert engineered for hard turning applications, providing stable cutting performance on hardened steels and wear‑resistant alloys. CBN grade WBS10 for hard turning Rhombic 55° insert geometry 0.4 mm corner radius for precise finishes 7° clearance angle for stable cutting Engineered for stable cutting in hard turning The insert is designed for demanding, wear‑intensive operations and delivers consistent performance in serial production. The use of CBN technology in the WBS10 grade focuses on abrasion resistance and heat tolerance, which reduces flank wear and prolongs tool life under high contact temperatures. The rhombic geometry combined with a 7° clearance angle promotes a stable cutting edge, resulting in predictable tool behaviour and lower rework rates. These technical characteristics translate into measurable process benefits such as reduced tool change frequency and more consistent part tolerances. Geometry and finish that improve surface quality and repeatability A controlled cutting edge geometry ensures that the machined surface meets finish requirements with fewer passes. The Rhombic 55° shape and 0.4 mm corner radius are optimised for turning operations where edge strength and repeatability matter. The insert’s profile supports secure chip formation, while the nominal T3 thickness contributes to rigidity at the cutting zone. Together, these features enable a balance between edge robustness and surface finish, helping to achieve the required dimensional stability across batches. Process reliability and economical productivity The combination of CBN grade and robust insert geometry is aimed at reducing total machining costs in hard material applications. Walter CBN / Hartstoff series inserts are intended for tasks where conventional grades would suffer rapid wear; the result is longer tool life and fewer interruptions for tool changes. For materials and specific cutting data, suitability should be verified against the product matrix to ensure optimum parameter selection. Where applicable, the insert supports higher cutting speeds and stable chip control, which contributes to lower cycle times and increased throughput in production environments. Contact Metav Werkzeuge for tailored application advice and rapid supply of Walter Tools inserts, or request consultation to determine the best grade and cutting data for the intended hard turning task. Technical data Article number: DCGW11T304EM-2-WBS10-WALTER Designation: DCGW11T304EM-2 WBS10 Product type: Indexable turning insert Manufacturer: Walter Tools Facts Insert size: 11 Corner radius: 0.4 mm Clearance angle: 7° Plate thickness: T3 Insert shape: Rhombus 55° Chipbreaker: 2 Tolerance class: G Special features Grade: CBN WBS10 Series: Walter CBN / Hartstoff Material: Catalogue-dependent Recommended for: hardened steels and high-wear alloys (verify product matrix) FAQ What materials is this insert intended for? The DCGW11T304EM-2 WBS10 insert is designed primarily for hardened steels and other wear‑intensive alloys; final suitability should be checked in the product matrix. How does the CBN WBS10 grade affect tool life? The CBN WBS10 grade provides high abrasion resistance and thermal stability, extending tool life in hard turning applications compared with conventional carbide grades. Which geometry benefits surface finish? The rhombic 55° shape with a 0.4 mm corner radius supports edge strength and repeatable surface quality for turning operations. Is the insert compatible with high cutting speeds? As a CBN grade from the Walter CBN series, this insert supports more aggressive cutting parameters in hardened materials; cutting data should be selected according to the application matrix. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is an original, factory‑new product of the manufacturer.
DCGW11T304FS-1 WDN10 Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, precise Rhombus 55° geometry, and consistent edge life for efficient turning of abrasive non‑ferrous materials; order the DCGW11T304FS-1 WDN10 directly via Metav Werkzeuge or ask our consultants for application advice. DCGW11T304FS-1 WDN10 Drehwendeschneidplatte by Walter Tools — PCD grade for abrasive non‑ferrous materials The DCGW11T304FS-1 WDN10 is a turning insert designed for stable, high‑precision machining of abrasive, non‑iron materials and composites, offering a robust polycrystalline diamond grade in a Rhombus 55° form. Polycrystalline diamond grade WDN10 Rhombus 55° geometry for versatile turning 7° clearance reduces flank rubbing 0.4 mm corner radius for accurate edge definition High wear resistance for abrasive non‑ferrous machining The PKD construction of this insert provides outstanding wear resistance, especially on abrasive, non‑ferrous materials such as aluminium alloys with abrasive fillers, copper alloys and certain composites. The WDN10 grade is a polycrystalline diamond solution engineered to retain cutting edge integrity where conventional carbide tools would wear rapidly. For production runs that demand long tool life and repeatable part quality, this choice reduces tool changes and minimises unplanned downtime, directly supporting continuous manufacturing workflows. Geometry that stabilises cutting and improves surface finish The Rhombus 55° shape in combination with a 7° clearance angle delivers a balanced cutting geometry that keeps cutting forces predictable while maintaining accessibility for a range of turning operations. The modest 0.4 mm corner radius supports a firm edge that resists chipping and yields a consistent surface finish on the workpiece. Such geometry reduces vibration and helps achieve reliable dimensional control, which is particularly useful on components requiring tight tolerances or fine external profiles. PCD grade and selection advice for reliable production The insert is produced in a polycrystalline diamond (PCD/PKD) grade, noted here as WDN10, which suits abrasive, non‑iron materials. The bulk substrate and diamond layer combination is catalogue‑dependent and should be matched to the specific workpiece material and machining conditions. Selection guidance: check the material matrix before final specification; for interrupted cuts or very hard inclusions, evaluate suitability against specific process data. Correct grade selection ensures consistent tool life and optimised cycle times. Operational efficiency and integration into processes With a T3 thickness and the compact 11 mm plate size, the insert integrates easily into standard tool holders for turning operations and offers predictable clamping behaviour. The controlled chip‑forming features minimise recutting and support stable chip evacuation, contributing to safer, more efficient turning cycles. By choosing this insert, production engineers gain a combination of process stability and reduced tooling interventions, which supports higher throughput and lower overall manufacturing cost per part. For high‑wear, high‑consistency turning of abrasive non‑ferrous materials, specify the WDN10 PKD grade from Walter Tools and contact Metav Werkzeuge for tailored application support or to place an order via Metav Werkzeuge — 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 Technical data SKU: DCGW11T304FS-1-WDN10-WALTER Designation: DCGW11T304FS-1 Brand: Walter Tools Grade: WDN10 Execution: W Series: Walter Schneidstoffsorte - Serie offen Facts Clearance angle: 7° Corner radius: 0.4 mm Insert size: 11 Insert shape: Rhombus 55° Thickness: T3 Tolerance class: G Chipbreaker: 1 Special features Material: catalogue‑dependent Coating: not specified Cutting material: polycrystalline diamond (PCD/PKD) Intended application: abrasive, non‑iron materials and composites Series note: check product matrix for specific workpiece suitability FAQ What materials is this insert suited for? The DCGW11T304FS-1 WDN10 insert is designed for abrasive, non‑ferrous materials; the WDN10 PCD grade performs especially well on aluminium alloys with abrasive inclusions, copper alloys and similar non‑iron materials. How does the Rhombus 55° shape affect machining? Rhombus 55° provides a versatile cutting geometry that improves access to external and profile turns while balancing cutting forces for more stable machining with the WDN10 grade. Is the corner radius suitable for fine finishes? Yes, the 0.4 mm corner radius offers a robust edge that supports accurate edge formation and consistent surface finish without excessive edge fragility. Does this insert require a specific holder or clamp? Standard turning holders compatible with DCGW inserts and appropriate clamping for 11 mm size and T3 thickness are suitable; ensure correct seat and stable clamping to exploit the insert's performance. How should users choose between PCD grades? Selection should follow the manufacturer's material matrix; WDN10 is intended for abrasive non‑ferrous materials, but confirm against the workpiece specifics and cutting parameters for optimal results. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCGW11T304TM-2 WBH10 Wendeplatten - Walter Tools
Take advantage of the combination of durable CBN cutting grade, precise 55° rhombic geometry and controlled chip formation for consistent hard-turning performance; order directly via Metav Werkzeuge or consult our specialists for application recommendations. DCGW11T304TM-2 WBH10 indexable turning insert (CBN) by Walter Tools — for hard turning, 7° clearance DCGW11T304TM-2 WBH10 is an indexable turning insert designed for hard machining applications, engineered to deliver stable wear behaviour in hardened steels and comparable materials. *CBN grade WBH10 for hard materials *7° clearance angle for controlled cutting action *Rhombic 55° geometry for versatile turning *0.4 mm nose radius for consistent surface finish Reliable performance for hardened steels and high wear resistance The insert employs a CBN grade WBH10, optimised for the high demands of hard machining. Cubic boron nitride (CBN) provides exceptional wear resistance and thermal stability compared with conventional carbide, which translates into extended tool life when machining hardened steels or pre-hardened workpieces. As a result, production runs benefit from fewer index changes and steadier process windows, supporting predictable cycle times and reduced operational interruptions. Geometry that improves surface quality and dimensional control A rhombic 55° cutting form combined with a 7° clearance angle and a 0.4 mm nose radius gives a balance between durability and finish capability. The geometry reduces cutting forces at the engagement point and helps control chip flow with the integrated chipbreaker stage 2, which supports consistent evacuation during interrupted cuts or tough alloys. The modest nose radius aids in achieving fine surface finishes without sacrificing edge strength, making the insert suitable for finish and semi-finish turning operations. Process security and application guidance for production environments Produced within the Walter CBN / Hartstoff series and manufactured to tolerance class G, this insert suits repetitive, high-pressure turning tasks where stable edge performance is required. Its designation and plate thickness T3 ensure compatibility with common clamping systems for indexable inserts of this family. Use is primarily directed at hardened and pre-hardened steels, where the material properties demand abrasive-resistant cutting edges; the result is a more reliable machining process and lower overall tool consumption per part. For tailored recommendations on integrating Walter Tools CBN inserts into existing turning processes, contact Metav Werkzeuge for application support and availability: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: DCGW11T304TM-2-WBH10-WALTER ISO designation: DCGW11T304TM-2 WBH10 Series: Walter CBN / Hartstoff Grade: WBH10 Manufacturer: Walter Tools Facts Clearance angle: 7° Nose radius: 0.4 mm Insert form: Rhombus 55° Insert size: 11 Thickness: T3 Chipbreaker: 2 Tolerance class: G Execution: W Special features CBN cutting material WBH10 Suitable for hardened steels (H) Suitable for pre-hardened steels Integrated chip control (chipbreaker 2) Part of Walter CBN / Hartstoff series FAQ Which materials are best machined with this insert? The DCGW11T304TM-2 WBH10 insert is intended primarily for hardened steels and pre-hardened materials; the CBN composition of the WBH10 grade gives the insert the required abrasion resistance for such applications. What does the 0.4 mm nose radius mean for surface finish? A 0.4 mm nose radius supports finer surface finishes while maintaining edge robustness; the geometry of this insert helps achieve consistent dimensional accuracy and surface quality in finishing passes. How does the chipbreaker stage affect machining? The chipbreaker (stage 2) assists in controlled chip formation and evacuation, reducing the risk of entanglement during interrupted cuts and contributing to stable cutting forces across the workpiece. Is this insert compatible with common turning holders? The insert follows standard indexable insert dimensions and tolerance class G; compatibility depends on the specific toolholder family, so matching the DCGW11T304TM-2 form with corresponding clamping seats is recommended. What production advantages does the CBN grade WBH10 offer? WBH10 provides extended tool life and steady edge behaviour in hard turning, which reduces index changes and supports continuous production runs with consistent part quality. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Walter AG (marketed as Walter Tools) is a leading manufacturer of precision metalcutting solutions with a global presence and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners and are mentioned here for explanatory purposes only. There is no affiliation between Metav Werkzeuge and the named brands; the listed item is an original, factory-new product from the manufacturer.
DCGW11T304TM-2 WBH10C WBH10C Wendeplatten - Walter Tools
High wear resistance and consistent edge stability from the WBH10C CBN grade combine with a compact Rhombus 55° geometry and a fine 0.4 mm corner radius to deliver dependable hard‑turning performance; order directly via Metav Werkzeuge or request application advice from our specialists. DCGW11T304TM-2 WBH10C — Indexable turning insert (CBN, Rhombus 55°) | Walter Tools The DCGW11T304TM-2 WBH10C is an indexable turning insert engineered for hard turning and wear‑intensive operations, primarily on hardened steels and similar high‑hardness materials. CBN grade WBH10C for hardened steels Rhombus 55° geometry for flexible turning 0.4 mm corner radius for fine surface finish Maximised process stability for hard turning The WBH10C grade is a coated CBN cutting material developed for high‑wear environments and the machining of hardened steels. Its abrasion‑resistant microstructure preserves the cutting edge under elevated temperatures and pressures, resulting in reduced flank wear and more predictable tool life. For production settings where stability and repeatability are priorities, this insert supports consistent cycle times and fewer interruptions for tool changes, improving overall throughput and economic efficiency. Geometry tuned for consistent surface quality The Rhombus 55° shape, combined with a 7° clearance angle and a 0.4 mm corner radius, produces a balanced cutting action that favours both profile versatility and surface finish. The compact form factor minimises cutting forces in interrupted cuts while the specified corner radius helps achieve smoother finishes on final passes. The integrated chipbreaker 2 aids controlled chip formation, lowering the risk of built‑up edge and maintaining reliable chip evacuation in turning operations. Practical integration and application benefits With a plate size of 11 and thickness T3, the insert fits common indexable turning systems used in CNC lathes and toolholders, enabling rapid index changes and straightforward inventory handling. The series designation Walter CBN / hard material indicates suitability for hard machining, including hardened steel and — depending on the specific application — certain cast materials or superalloys. This combination of material and form reduces downtime and supports higher‑value finishes, making it a solid choice for shops focused on productivity and repeatable part quality. For tailored machining recommendations or to source the DCGW11T304TM-2 WBH10C, contact Metav Werkzeuge: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: DCGW11T304TM-2-WBH10C-WALTER ISO designation: DCGW11T304TM-2 WBH10C Manufacturer: Walter Tools Facts Plate size: 11 Thickness: T3 Clearance angle: 7° Corner radius: 0.4 mm Geometry: Rhombus 55° Chipbreaker: 2 Tolerance class: G Special features Series: Walter CBN / hard material Grade: WBH10C (coated CBN) Suitable for hardened steels Intended for hard turning and wear‑intensive tasks FAQ Which materials is this insert primarily designed for? The DCGW11T304TM-2 WBH10C insert is primarily designed for hardened steels, where the WBH10C CBN grade provides the wear resistance required for hard‑turning operations. How does the Rhombus 55° geometry affect machining? Rhombus 55° geometry offers flexibility for a range of turning operations; the shape balances cutting forces and tool engagement to support both profiling and finishing passes with the indexable insert. What surface finish can be expected with a 0.4 mm corner radius? A 0.4 mm corner radius supports fine surface finishes on finishing passes while still providing sufficient edge strength for interrupted cuts when used with the correct feeds and speeds. Is this insert compatible with standard CNC turning toolholders? Yes, the insert’s size and thickness correspond to common indexable insert standards, allowing integration with conventional turning toolholders used in CNC lathes. When is CBN preferable to carbide for turning? CBN, as used in the WBH10C grade, is preferable when machining hardened steels or other high‑hardness materials because it retains edge integrity at higher temperatures and resists abrasive wear better than carbide options. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is original, factory‑new goods of the manufacturer.
DCGW11T304TM-2 WBH20 Wendeplatten - Walter Tools
The CBN grade WBH20 combines high wear resistance and a stable cutting edge for reliable performance in hard turning; its Rhombic 55° geometry and 7° clearance deliver consistent surface quality and process security. Order the DCGW11T304TM-2 WBH20 directly via Metav Werkzeuge or request advice from our technical consultants. DCGW11T304TM-2 WBH20 – CBN turning insert, Rhombic 55°, 7° clearance (Walter Tools) A DCGW11T304TM-2 WBH20 turning insert engineered for high‑performance hard machining of hardened steels and comparable high‑wear materials CBN grade WBH20 for hard materials Rhombic 55° geometry for versatile turning 7° clearance angle for stable cutting 0.4 mm nose radius for precise finishes Consistent tool life for hard machining The use of CBN (cubic boron nitride) in the WBH20 grade provides exceptional wear resistance, which is critical when working with hardened steels. This insert is designed to maintain a stable cutting edge under high thermal and mechanical load, so machining cycles run with fewer interruptions. The result is a predictable tool life and reduced downtime, which supports continuous production and cost efficiency in demanding turning operations. Geometry tuned for dimensional accuracy The Rhombic 55° shape and a 0.4 mm nose radius enable accurate profile generation while balancing strength at the cutting edge. Combined with the 7° clearance, the geometry reduces rubbing and ensures reliable chip formation, improving surface finish and dimensional control. These features help achieve consistent part quality with minimal rework, particularly when tight tolerances are required. Suitable for hardened and pre‑hardened steels Classified for applications with hardened steels, this grade is a practical choice for hard turning and finishing of components that would rapidly wear conventional carbide inserts. The WBH20 composition is optimised for stable chip control and long life in high‑hardness environments, making it suitable where repeatability and process security are essential. The insert’s specifications align with ISO group H machining demands. Economic advantages through fewer tool changes By reducing the frequency of insert changes and maintaining a consistent cutting edge, the insert contributes to lower operating expenses and higher throughput. Improved durability means less setup time and fewer tool inventories to manage. For machining centres producing hardened parts, this translates into measurable gains in productivity and a clearer return on tooling investment. For technical clarification or to secure genuine Walter Tools turning inserts, contact Metav Werkzeuge for tailored application advice and rapid supply via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: DCGW11T304TM-2-WBH20-WALTER Designation: DCGW11T304TM-2 WBH20 Manufacturer: Walter Tools Product type: Turning insert Series: Walter CBN / Hard material Facts Clearance angle: 7° Corner radius: 0.4 mm Shape: Rhombus 55° Plate size: 11 Thickness: T3 Chipbreaker: 2 Tolerance class: G Special features Grade: WBH20 (CBN) Application: Hardened steels (ISO group H) Series description: CBN cutting material for hard machining Benefits: High wear resistance, stable cutting edge, productive hard turning FAQ What materials is this insert intended for? This turning insert, DCGW11T304TM-2 WBH20 from Walter Tools, is intended primarily for hardened steels and related high‑wear materials classified under ISO group H. How does the WBH20 grade improve process stability? The WBH20 CBN grade provides superior wear resistance and edge stability, which reduces tool degradation and supports consistent machining performance during hard turning. Can the insert be used for finishing operations? Yes, the combination of Rhombic 55° geometry and a 0.4 mm nose radius enables accurate finishes, making the insert suitable for finishing passes on hardened components. Is this insert compatible with common turning holders? The DCGW11T304TM-2 WBH20 follows standard insert geometries and can be mounted in appropriate holders designed for Rhombic 55° turning inserts; holder selection should match the insert thickness and seat geometry. What advantage does CBN offer over carbide in this application? CBN materials like WBH20 resist abrasive wear much better than carbide when machining hardened steels, resulting in longer tool life and fewer interruptions for insert changes. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. There is no connection between our company and the named brands beyond the sale of original factory-new products. The offered article is an original, factory‑new product of the manufacturer Walter Tools.
DCGW11T304TM-2 WBH20C Wendeplatten - Walter Tools
The combination of a CBN cutting grade, a rhombic 55° geometry and a finely tuned 7° relief delivers repeatable performance in hard-turning operations, reducing downtime and extending tool life. Benefit from high wear resistance and consistent chip control for reliable production. Order the DCGW11T304TM-2 WBH20C turning insert directly via Metav Werkzeuge or ask our consultants if needed. DCGW11T304TM-2 WBH20C turning insert — Walter Tools — CBN grade for hard turning, Rhombic 55° A high-performance indexable turning insert designed for hard and pre-hardened steels, offering a coated CBN grade and a robust rhombic geometry for stable metal removal. Coated CBN grade for hard turning Rhombic 55° insert geometry 7° relief angle for improved clearance Corner radius 0.4 mm for predictable edge life Engineered for reliable hard-turning productivity The coated CBN composition is optimised for machining hardened steels, which demand exceptional wear resistance and thermal stability. This insert provides a durable cutting edge that preserves geometry under the high contact temperatures and forces typical of hard turning. The result is long tool life and fewer tool changes, which directly improves process throughput and reduces production cost-per-part. The indexable design permits quick indexing and predictable tool change intervals, supporting continuous operation in demanding CNC turning centres. Geometry that promotes consistent surface quality and chip control The rhombic 55° shape combined with a 7° relief and a corner radius of 0.4 mm delivers a balance between strength and cutting engagement. This geometry aids in producing a stable cutting force vector and controlled chip breakage, which helps to maintain precision and surface finish across long production runs. Where tight tolerances are required on pre-hardened components, the combination of geometry and the CBN grade reduces the tendency for built-up edge and chatter, supporting repeatable results. Practical benefits for workshop and production planning Thanks to its wear-resistant compound and compact dimensions (insert size 11, thickness T3), the insert supports high productivity in batch and single-piece flow environments. The specification reduces unplanned interventions by lowering flank and crater wear rates, so tool-life planning becomes more reliable. For operations moving between heat-treated parts and pre-hardened workpieces, this insert offers a cost-effective route to maintain cycle times while reducing scrap and rework. Clear application guidance and material fit The insert is especially suited to the ISO H material group — hardened steels — and is recommended for precision hard turning and finishing passes where dimensional stability matters. Its chipbreaker and edge geometry help manage the tougher chips produced by such alloys. When selecting cutting parameters, favour moderate depths of cut with controlled feed to exploit the insert’s edge stability; this will deliver predictable wear patterns and consistent surface integrity over extended runs. For demanding hard-turning tasks, specify the Walter Tools DCGW11T304TM-2 WBH20C through Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 for technical guidance and availability Technical data Article number: DCGW11T304TM-2-WBH20C-WALTER Type: Turning insert (indexable) Designation: DCGW11T304TM-2 WBH20C Manufacturer: Walter Tools Series: Walter CBN / Hartstoff Facts Relief angle: 7° Corner radius: 0.4 mm Insert shape: Rhombic 55° Insert size: 11 Thickness: T3 Chipbreaker: 2 Tolerance class: G Special features Coated CBN cutting grade WBH20C Suited for hardened steels (ISO H) Designed for hard turning and finishing Indexable insert for fast indexing and replacement FAQ Is this insert suitable for hardened steels? Yes. The DCGW11T304TM-2 WBH20C uses a coated CBN grade specifically intended for machining hardened steels (ISO H) and for precision hard-turning tasks. What edge preparation does the insert have for finish turning? The insert offers a corner radius of 0.4 mm and a rhombic 55° geometry, which together support stable cutting and good surface finish during finishing passes. Can this insert handle pre-hardened steel applications? The DCGW11T304TM-2 WBH20C is suitable for pre-hardened steel applications and is designed to provide consistent wear behaviour on such materials. How does the chip control perform with this grade? The combination of the CBN grade and the chipbreaker geometry gives reliable chip control under the typical temperatures and forces of hard turning, reducing risk of edge build-up. Which operations benefit most from this insert? This insert is ideal for hard turning and finishing where repeatability, extended tool life and surface integrity are priorities, particularly in medium to high-volume production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners and are mentioned for explanatory purposes only. There is no affiliation or connection between our company and the referenced brands. The offered item is an original, factory-new product from the respective manufacturer.
DCGW11T304TM-2 WBH30 Wendeplatten - Walter Tools
Take advantage of the CBN-grade WBH30 for reliable hard-turning performance and the Rhombic 55° geometry for flexible tool approach; the combination reduces tool changes and keeps production running. Order the DCGW11T304TM-2 WBH30 turning insert directly via Metav Werkzeuge or ask our consultants if needed. DCGW11T304TM-2 WBH30 indexable turning insert — CBN grade for hard machining | Walter Tools DCGW11T304TM-2 WBH30 is an indexable turning insert engineered for hard and pre-hardened steel applications, offering high wear resistance and consistent finish in demanding production environments. CBN grade WBH30 for hardened steels Rhombic 55° shape for adaptable cutting angles 7° clearance for improved chip flow 0.4 mm nose radius for precise surface finish Extended tool life through CBN technology The core advantage of this insert is the CBN cutting material in the WBH30 grade, designed for the high abrasion and contact pressures typical of hard turning. Cubic boron nitride inserts deliver superior wear resistance compared with conventional carbides when machining hardened steels and pre-hardened components. This durability translates into fewer indexings, longer uninterrupted runs and lower tool-related downtime, which supports higher overall productivity and reduced cost per produced part. Stable process and consistent surface quality With its Rhombic 55° geometry and a 0.4 mm nose radius, the insert enables controlled chip formation and reliable contact conditions at the cutting edge. The specified 7° clearance helps prevent rubbing on the flank, while the chipbreaker 2 geometry supports repeatable chip control under tough conditions. Together these attributes improve surface integrity and dimensional consistency, making the insert suitable for finishing passes on hardened components where repeatability and surface quality are decisive. Practical integration and machining guidance This indexable plate is listed under the Walter CBN / hard-material series and is suitable for machining tasks classified as ISO group H (hardened steels). The ISO designation DCGW11T304TM-2 WBH30 identifies form, size and grade for straightforward tool selection and inventory management. For process planning, expect extended tool life compared with carbide alternatives; machining parameters should be adjusted to the increased cutting-edge stability of CBN to exploit higher feed and cutting speeds safely. If additional cutting data is required, Metav Werkzeuge provides tailored guidance and application advice. Contact Metav Werkzeuge today to source the Walter Tools DCGW11T304TM-2 WBH30 CBN insert for hard-turning applications and request cutting-parameter recommendations or material-specific data Technical data Article number: DCGW11T304TM-2-WBH30-WALTER Manufacturer: Walter Tools Product type: indexable turning insert ISO designation: DCGW11T304TM-2 WBH30 Series: Walter CBN / hard-material Facts Clearance (free) angle: 7° Nose radius: 0.4 mm Insert form: Rhombic 55° Insert size: 11 Thickness: T3 Chipbreaker: 2 Tolerance class: G Special features Grade: WBH30 (CBN cutting material) Application: hard turning / machining of hardened steels (ISO H) Suitable for pre-hardened steel applications Robust edge stability for high abrasion environments FAQ What materials is this insert suited for? The DCGW11T304TM-2 WBH30 insert is specified for hardened steels and pre-hardened workpieces, classified under ISO group H. How does the WBH30 grade improve production? WBH30's CBN composition provides superior wear resistance and edge stability, allowing longer tool life and fewer interruptions in serial production. Which geometry ensures good surface finish with this insert? The Rhombic 55° form combined with a 0.4 mm nose radius and chipbreaker 2 produces controlled chip formation and consistent surface integrity. Is the insert compatible with standard toolholders? The ISO designation DCGW11T304TM-2 WBH30 identifies the insert form and size for compatibility with corresponding toolholder systems designed for DCGW-style plates. Where can cutting data or process parameters be obtained? Cutting-parameter recommendations and application-specific data are available from Metav Werkzeuge and the Walter Tools technical literature for the WBH30 grade. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCGW11T304TS-2 WBK20 Wendeplatten - Walter Tools
Take advantage of CBN wear resistance and a rhombic 55° geometry to extend tool life and improve surface quality in hard-material turning; order directly via Metav Werkzeuge or consult their specialists for application support. DCGW11T304TS-2 WBK20 turning indexable insert — CBN grade, rhombic 55°, Walter Tools The DCGW11T304TS-2 WBK20 is a rhombic 55° turning indexable insert designed for hard and high-wear turning tasks, offering a balance of edge stability and surface finish in demanding production environments CBN grade for hardened materials Rhombic 55° geometry for versatile turning 7° clearance and 0.4 mm nose radius Durable CBN performance for high-wear turning The WBK20 grade is a CBN cutting material developed for machining hardened steels and other wear-intensive tasks; this results in markedly higher tool life compared with conventional grades when operating in the intended hardness range. The superior wear resistance reduces the frequency of tool changes, which in turn lessens machine downtime and contributes to a lower cost per component in continuous production. The clear technical consequence is improved process stability and predictable repeatability in series turning. Geometry that balances strength and surface quality With a rhombic 55° geometry, a 0.4 mm nose radius and a 7° clearance angle, the insert is configured to deliver a compromise between cutting-edge strength and a fine surface finish. The modest nose radius helps maintain dimensional control on short-chipping operations while the clearance angle reduces rubbing on the flank face. The designated chipformer type (chipbreaker 2) supports effective chip control, which lowers the risk of re-cutting and contributes to a consistent finish without sacrificing cutting-edge robustness. Practical integration and application guidance The insert is produced in a T3 thickness with tolerance class G, which supports compatibility with standard turning toolholders designed for rhombic 55° inserts. The Walter Tools series designation indicates a catalogue-dependent material offering; verify the product matrix for exact workpiece-material matches, particularly for specialist substrates. For complex component series or fluctuating batch sizes, the combination of CBN wear properties and the chosen geometry often leads to fewer tool set-ups and more predictable cycle times, benefiting shop-floor efficiency and scheduling. For applications requiring reliable CBN performance choose the Walter Tools WBK20 insert and contact Metav Werkzeuge for technical advice and availability: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: DCGW11T304TS-2-WBK20-WALTER Designation: DCGW11T304TS-2 WBK20 Type: Turning indexable insert Core dimensions Plate form: Rhombus 55° Plate size: 11 Nose radius: 0.4 mm Clearance angle: 7° Plate thickness: T3 Tolerance class: G Features and applications Grade: WBK20 (CBN cutting material) Series: Walter Schneidstoffsorte - Serie offen Chipformer: 2 Execution: W Material specification: catalogue-dependent Application note: suitability for hardened steels and high-wear tasks; check product matrix FAQ Which materials is this insert intended for? The DCGW11T304TS-2 WBK20 insert uses a CBN grade optimised for hardened steels and other high-wear materials; suitability for specific alloys should be checked against the product matrix. How does the 55° rhombic form influence machining? The rhombic 55° geometry provides a versatile approach for turning operations, enabling a balance between cutting-edge strength and accessible cutting angles for general and finishing cuts with the WBK20 grade. What role does the nose radius play for surface finish? A 0.4 mm nose radius promotes dimensional control on short-chipping cuts while contributing to a consistent surface quality when combined with the insert geometry and cutting parameters. Is chip control a focus for this insert? Yes, the chipformer designation (type 2) supports improved chip control, which aids in stable machining and reduces the likelihood of chip-related surface defects. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Brand names and registered designations are mentioned for clarification only and do not imply any affiliation between our company and the referenced brands. The item offered is an original, factory-new product from the manufacturer.
DCGW11T308EM-2 WBS10 WBS10 Wendeplatten - Walter Tools
Taking advantage of the CBN WBS10 grade for high wear resistance, the Rhombus 55° geometry and a 7° clearance angle guarantee stable cutting and consistent edge life in hard-material turning. Order the insert directly via Metav Werkzeuge or consult our specialists for cutting data and compatibility. DCGW11T308EM-2 WBS10 Turning Insert — CBN, Rhombus 55° (Walter Tools) The DCGW11T308EM-2 WBS10 is a CBN indexable turning insert designed for demanding finishing and hard-material turning tasks, offering a compact Rhombus 55° form for versatile mounting and approach angles. CBN grade WBS10 for high wear resistance Rhombus 55° geometry for versatile turning 7° clearance angle for stable cutting action 0.8 mm corner radius for improved edge strength Maximise tool life for hardened components The CBN-based WBS10 cutting grade is engineered for high-wear environments and delivers consistent edge life when machining hardened steels and similarly demanding materials. As a superabrasive, CBN sustains cutting performance under elevated temperatures and maintains a sharp cutting edge longer than conventional carbides, which reduces the frequency of index changes and supports predictable production schedules. For operations where downtime must be limited, this insert provides a measurable improvement in run-time stability and process reliability. Geometry that improves surface finish and control The Rhombus 55° form combined with a 7° clearance and a 0.8 mm corner radius balances strength and finish. The 55° approach allows flexible insert orientation for general turning and light profiling, while the small corner radius increases edge robustness without compromising surface quality. The modest clearance angle reduces flank rubbing during engagement, lowering vibration and improving dimensional consistency. These geometric choices translate directly into fewer rework cycles and a steadier path to the required surface specifications. Efficiency and process security in production By selecting a dedicated CBN solution for abrasive, hardened workpieces, workshops benefit from reduced tool change frequency and enhanced material removal predictability. The insert’s construction supports stable chip formation and steady cutting forces, contributing to higher machine utilisation and lower per-part tooling costs over long runs. Walter Tools’ production standards aim for high process security and repeatable results, which helps preserve component tolerances and supports continuous, efficient machining operations. Practical application notes and compatibility This indexable insert is primarily intended for hard and highly abrasive tasks; confirmation of suitability for specific alloys or cast materials should be made against the product matrix. The insert’s thickness T3, chipbreaker configuration and Rhombus 55° shape make it adaptable to a range of turning setups, but cutting data must be tuned to the lathe and workholding in use. For unusual substrates such as superalloys or cast iron variants, please verify the application guidance to ensure optimum cutting parameters and coolant strategy. For tailored advice on integrating the DCGW11T308EM-2 WBS10 CBN turning insert into production, contact Metav Werkzeuge for cutting data, availability and application support at info@metav-werkzeuge.com or +49 2822 7131930. Technical Data Article number / SKU: DCGW11T308EM-2-WBS10-WALTER ISO designation: DCGW11T308EM-2 WBS10 Series: Walter CBN / Hartstoff Execution: W Tolerance class: G Data Clearance angle: 7° Corner radius: 0.8 mm Insert size: 11 Thickness: T3 Chipbreaker: 2 Special features CBN cutting grade WBS10 Rhombus 55° insert geometry Catalogue-dependent base material / substrate Designed for hard and highly abrasive turning tasks Intended use: check product matrix for material suitability FAQ What materials is this CBN insert best suited for? This CBN insert is designed primarily for hardened steels and other high-wear applications; suitability for specific alloys should be checked against the product matrix for the DCGW11T308EM-2 WBS10. How does the Rhombus 55° geometry affect machining? The Rhombus 55° shape allows flexible approach angles and general-purpose turning, improving accessibility and enabling stable cutting when used with the DCGW11T308EM-2 WBS10 insert. Can this insert replace carbide grades for hardened workpieces? For many hardened turning tasks, the WBS10 CBN grade provides longer edge life and better wear resistance than conventional carbides, making the insert a suitable alternative where hardness and abrasion limit carbide performance. What should be checked before applying this insert to a new material? Confirm the material in the product matrix and adjust cutting data to machine setup; the DCGW11T308EM-2 WBS10 requires specific speeds and feeds for optimal wear behaviour. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered article is an original, factory-new product of the manufacturer.
DCGW11T308FS-1 WDN10 Wendeplatten - Walter Tools
Taking advantage of the WDN10 polycrystalline diamond grade and the rhombic 55° form delivers higher process reliability and extended tool life in abrasive non‑ferrous applications; combine this with the fine 0.8 mm corner radius for improved profile control. Order the insert directly via Metav Werkzeuge or contact the consultants for selection support. DCGW11T308FS-1 WDN10 — Turning indexable insert, PCD grade for abrasive non‑ferrous machining | Walter Tools The DCGW11T308FS-1 WDN10 is a polycrystalline diamond turning insert engineered for machining abrasive, non‑ferrous materials where wear resistance and consistent surface quality are essential. PCD grade WDN10 for abrasive non‑ferrous materials Rhombic 55° insert form for versatile cutting 0.8 mm corner radius for fine profile control 7° clearance angle for steady chip flow Maximise uptime with wear‑resistant PCD performance Selected for demanding non‑ferrous and abrasive applications, this insert features polycrystalline diamond (PCD) as the cutting material, marked here as WDN10. PCD delivers exceptional wear resistance, significantly reducing flank and crater wear when machining abrasive alloys and composite materials. The result is longer intervals between index changes and improved batch consistency, translating into measurable gains in productivity and process economy. The carbide substrate and hardened bond system ensure stable mounting and repeatable positioning during multi‑part production. Precision geometry for predictable surface finish and profile control The rhombic 55° geometry combined with a 0.8 mm corner radius balances edge strength and finishing capability. This geometry supports accurate contouring and small‑step profiling while maintaining edge stability under interrupted cuts. The 7° clearance angle contributes to smooth chip evacuation and reduces rubbing along the flank, helping to maintain surface integrity and dimensional accuracy in serial turning operations. Clear geometry choices like these simplify tooling decisions for engineers seeking reproducible results. Chip control and process security for industrial workflows A defined chipbreaker and the insert’s form factor assist controlled chip formation even in short‑chipping and abrasive materials. Stable chip behaviour reduces the risk of built‑up edge and tool vibration, which in turn protects the workpiece surface and downstream operations. By combining PCD hardness with the insert’s geometry, components achieve consistent surface quality with fewer reworks. The open series design of the cutting grade offers practical flexibility across a range of machine setups and clamping systems, aiding in rapid integration into existing production lines. Contact Metav Werkzeuge today for tailored advice on inserting the DCGW11T308FS-1 WDN10 into current processes and to confirm the best grade selection for a given material or component geometry: info@metav-werkzeuge.com — +49 2822 7131930 Technical data Article number: DCGW11T308FS-1-WDN10-WALTER Model designation: DCGW11T308FS-1 ISO designation: DCGW11T308FS-1 WDN10 Series: Walter Schneidstoffsorte - Serie offen Grade: WDN10 Execution: W Tolerance class: G Core measurements Insert size: 11 Thickness: T3 Corner radius: 0.8 mm Clearance angle: 7° Insert form: Rhombus 55° Chipbreaker: 1 Materials & special features Material: Catalogue dependent Cutting material: Polycrystalline diamond (PCD) — high wear resistance Intended for abrasive non‑ferrous materials and non‑ferrous alloys Open series for flexible grade selection Stable edge control and reproducible positioning FAQ Which materials suit this insert best? The DCGW11T308FS-1 WDN10 is a PCD insert optimised for abrasive non‑ferrous materials and non‑ferrous alloys; check the product matrix for precise material matching. What is the corner radius and how does it affect finish? The insert has a 0.8 mm corner radius, which provides a balance between edge strength and fine surface finishing for profile work. What insert form and clearance does it use? This item has a rhombic 55° form with a 7° clearance angle, aiding chip flow and enabling versatile turning strategies. Can the insert handle interrupted cuts or roughing operations? The PCD grade focuses on wear resistance for abrasive work; while robust, suitability for heavy interruption should be evaluated against the specific application and machine capability. How is chip control achieved with this insert? Chip control is supported by the defined chipbreaker and the insert geometry, which together promote short, manageable chips in abrasive non‑ferrous machining. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCGW11T308TM-2 WBH10 Wendeplatten - Walter Tools
Taking advantage of a highly wear‑resistant CBN grade and a stable rhombic geometry ensures consistent performance in hard turning operations; order the insert directly via Metav Werkzeuge or consult the technical advisors for application-specific guidance. DCGW11T308TM-2 WBH10 – CBN turning insert for hard turning, Walter Tools A DCGW11T308TM-2 WBH10 indexable turning insert engineered for heavy wear and hard material machining, particularly suited to precision turning of hardened steels. CBN grade WBH10 for high wear resistance Rhombic 55° geometry for versatile turning 0.8 mm corner radius and 7° rake angle High‑performance cutting where durability matters The insert is based on CBN technology and the WBH10 grade, providing exceptional resistance against abrasive and adhesive wear in hard machining tasks. For component production where tool life translates directly to uptime, the use of a cubic boron nitride cutting material reduces flank wear and maintains a stable cutting edge over extended cycles. This results in fewer tool changes and predictable process windows. The combination of a robust cutting material with a carefully selected geometry supports repeatable dimensional accuracy during series production. Geometry and edge design that stabilise the cut A rhombic 55° profile delivers a balance between entry angle and cutting force distribution, making the insert suitable for a wide range of turning operations, from facing to light profiling. The 0.8 mm corner radius increases edge strength for interrupted cuts while still allowing for fine surface finishes when matched with appropriate feeds. A measured 7° rake promotes controlled chip formation and reduces cutting temperatures in hard turning, which helps to protect the cutting edge and the workpiece microstructure. Explained plainly, these design choices mean fewer rejects and more consistent surface quality. Practical benefits for workshop productivity The insert’s thickness class T3 and the standard designation ensure compatibility with common turning toolholders, simplifying tooling logistics on the shop floor. Because the grade is optimised for hardened materials, machinability improvements are realised in parts made from heat‑treated steels where conventional carbide tooling would wear prematurely. Fewer interruptions for tool changes and stable machining parameters translate into faster cycle times and lower unit production costs, offering a clear cost‑efficiency argument for batch and continuous production environments. Application guidance and process reliability Designed for hard turning and heavy wear conditions, the insert is suitable for components in sectors such as automotive, tooling and die, and heavy engineering where hardened steels are processed. Choosing the right feeds and speeds for a CBN grade is vital: moderately high cutting speeds with stable feeds yield the best balance of productivity and edge life. For new applications, start with conservative parameters and increase productivity once tool behaviour is established. Additional process support is available from Metav Werkzeuge, which can advise on optimal holder selection and cutting data. Secure Walter Tools CBN inserts from Metav Werkzeuge for long‑term hard‑turning performance — contact the Metav Werkzeuge team for tailored machining recommendations Technical Data Article number: DCGW11T308TM-2-WBH10-WALTER Product type: Turning indexable insert Designation: DCGW11T308TM-2 WBH10 Numbers / Core technical data Corner radius: 0.8 mm Free (rake) angle: 7° Plate size: 11 Thickness class: T3 Geometry: Rhombic 55° Tolerance class: G Chipbreaker: 2 Special features / Materials Grade: CBN WBH10 Series: Walter CBN / hard material Application: Hard turning / machining of hardened steels Suitable for: Hardened steels and pre‑hardened materials FAQ What materials is this insert designed to machine? The DCGW11T308TM-2 WBH10 insert from Walter Tools is specifically designed for machining hardened steels and other high‑wear applications where CBN tooling provides superior performance. How does the WBH10 grade improve tool life? The WBH10 CBN grade offers high abrasion resistance and a stable cutting edge, which reduces flank wear and extends tool life under the high contact stresses typical of hard turning. Which insert geometry should be chosen for general turning tasks? The rhombic 55° geometry of this insert provides a versatile compromise for facing and turning operations, delivering stable cutting forces and good access for profiling. Is this insert compatible with standard turning holders? Yes, the DCGW11T308TM-2 designation and T3 thickness class match common indexable insert holders; verify holder compatibility with the tool supplier before use. What edge preparation benefits does a 0.8 mm corner radius offer? A 0.8 mm corner radius increases edge strength for interrupted cuts and supports consistent surface finish when combined with appropriate feed rates. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected brand names and trademarks are the property of their respective owners. Brand names are mentioned solely for clarification; there is no connection implied between Metav Werkzeuge and the listed manufacturers. The offered item is an original, factory‑new product of the manufacturer.
DCGW11T308TM-2 WBH10C Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance and reliable process stability for efficient hard turning operations. The CBN grade and rhombic geometry deliver consistent results on hardened workpieces while minimising downtime. Order Walter Tools inserts through Metav Werkzeuge or consult our specialists for application advice. DCGW11T308TM-2 WBH10C Drehwendeschneidplatte — CBN grade for hardened steels, Walter Tools The DCGW11T308TM-2 WBH10C is a rhombic 55° turning insert with a CBN cutting grade, intended for hard turning of hardened steels and similar high-hardness materials. CBN grade WBH10C for hard turning Rhombic 55° geometry 7° relief angle, 0.8 mm corner radius T3 thickness, insert size 11 Exceptional cutting performance for hardened materials The combination of CBN cutting material and a rhombic 55° geometry delivers superior wear resistance and thermal stability during hard machining. Designed for operations on hardened steels, this insert maintains stable cutting conditions where conventional carbides would wear rapidly. The WBH10C grade is optimised for high contact loads and elevated temperatures, so tool life is extended and process interruptions are reduced. The specified corner radius 0.8 mm supports durable edge strength, enabling economically efficient finishing passes while sustaining surface quality on demanding components. Stable process and consistent surface integrity A controlled geometry together with the 7° relief significantly improves chip flow and contact mechanics at the cutting edge, which benefits repeatability and surface finish. The balanced design reduces the risk of premature edge chipping and helps to preserve dimensional accuracy during serial production. As a result, shops experience fewer reworks and more predictable cycle times. The Walter CBN series is known for producing stable chips and reliable edge behaviour, translating into lower overall machining costs and a more consistent end-product appearance. Seamless integration into machining cells and economical use The insert’s standardised format and T3 thickness allow straightforward integration into existing toolholders for turning operations, easing inventory management and tool changeover. Its suitability for pre-hardened and hardened steels makes it a versatile choice across grinding-replacement and hard-finishing tasks. Choosing this insert supports a pragmatic balance between performance and tool consumption: fewer insert changes, less downtime and an improved economic footprint for high-hardness applications. For newcomers to CBN tooling, the properties of WBH10C are simple to evaluate in a controlled test cut before full production deployment. Discuss Walter Tools CBN inserts with Metav Werkzeuge for tailored recommendations and procurement; contact via info@metav-werkzeuge.com or +49 2822 7131930 for application-specific advice Technical data Article number: DCGW11T308TM-2-WBH10C-WALTER Designation: DCGW11T308TM-2 WBH10C Product type: Drehwendeschneidplatte Brand: Walter Tools Facts Relief angle: 7° Corner radius: 0.8 mm Thickness: T3 Insert size: 11 Geometry: Rhombus 55° Special features Series: Walter CBN / Hartstoff Grade: WBH10C (coated CBN) Tolerance class: G Chipbreaker: 2 Suitable for: hardened steels (H) Suitable for: pre-hardened steel FAQ What materials is this insert intended for? The DCGW11T308TM-2 WBH10C from Walter Tools is designed primarily for hardened steels and is also suitable for many pre-hardened applications thanks to its CBN-based cutting grade. How does the WBH10C grade differ from carbide inserts? WBH10C is a coated CBN grade offering superior wear resistance and thermal stability compared with carbide, which gives a longer life when machining high-hardness materials with elevated contact temperatures. Which insert geometry is used and why does it matter? The rhombic 55° geometry provides a balance between cutting edge strength and accessibility for turning profiles, making it well suited to finishing and hard-turning applications where rigidity and surface integrity are priorities. Is the insert compatible with standard toolholders? The DCGW11T308TM-2 format follows common insert standards, so the insert can be mounted in compatible turning toolholders that accept this ISO-style geometry and thickness. What are the expected benefits in production when switching to CBN inserts? Switching to a CBN solution such as the Walter Tools WBH10C typically reduces tool change frequency, improves process stability and enhances surface finish on hardened components, yielding lower overall machining costs. Walter Tools: Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCGW11T308TM-2 WBH20 Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, stable cutting geometry and suitability for hardened steels to maintain uptime and reproducible component quality; order the indexable insert directly via Metav Werkzeuge or contact the technical consultants for application advice. DCGW11T308TM-2 WBH20 indexable turning insert (CBN, Rhombic 55°, 7° relief) — Walter Tools DCGW11T308TM-2 WBH20 is an indexable turning insert developed for hard machining tasks, optimised for high wear resistance and reproducible cutting performance in hardened and pre-hardened steels. CBN grade WBH20 for hardened steels Rhombic 55° shape for versatile turning 7° relief angle for secure cutting 0.8 mm corner radius for stable edge Engineered for hard turning with reproducible tool life The DCGW11T308TM-2 WBH20 insert uses a CBN-based grade tailored to high-wear applications; CBN provides exceptional abrasion resistance when machining hardened steels, which reduces flank wear and extends productive cutting time. This means fewer tool changes and more consistent cycle times across series production runs. For operations where tool life and repeatability influence process cost, the insert delivers a measurable contribution to overall efficiency while maintaining component tolerances. Geometry that stabilises cuts and improves surface finish The insert’s Rhombic 55° form and 7° relief establish a secure engagement with the workpiece and controlled chip flow; the 0.8 mm corner radius favours strength at the cutting edge and helps dampen vibration, resulting in improved surface integrity. The combination of geometry and edge preparation supports a stable cutting action even under elevated contact conditions, translating into fewer rework steps and a more reliable surface finish on turned parts. Process reliability and economical machining Belonging to the Walter CBN / hard material series, the grade WBH20 is designed specifically for hard machining applications and is suitable for both hardened and pre-hardened steel work. The insert’s resistance to abrasive wear provides greater process stability and reduces the frequency of insert indexing, supporting continuous production. Where cycle stability is critical, this indexable insert contributes to predictable tool-change intervals and helps to lower total machining costs through extended service life. Clear specification and application guidance for shop-floor integration The insert is supplied in a size 11 format with T3 thickness, a defined chipbreaker class and tolerance class G, making it straightforward to match to compatible toolholders. Its defined geometry and material designation simplify process planning for hard turning operations in automotive, tooling and engineering sectors. For selection of the correct holder and cutting parameters, Metav Werkzeuge’s technical team can provide tailored recommendations to ensure the insert meets the intended production requirements. For application support and availability of Walter Tools CBN inserts, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitable holders and cutting data for specific hardened-steel applications. Technical data Article number: DCGW11T308TM-2-WBH20-WALTER Manufacturer: Walter Tools Product type: Indexable turning insert Series: Walter CBN / hard material Grade: WBH20 Core technical data Relief angle: 7° Corner radius: 0.8 mm Shape: Rhombic 55° Insert size: 11 Thickness: T3 Chipbreaker: 2 Tolerance class: G Special features CBN-based wear-resistant grade Suited for hardened steels and pre-hardened steel Designed for hard machining and high abrasion conditions Stable cutting geometry for reproducible results FAQ What materials is this insert suitable for? The DCGW11T308TM-2 WBH20 insert (Walter Tools indexable turning insert) is intended for machining hardened steels and can also be used on pre-hardened steel, as indicated by its CBN-based WBH20 grade. How does the CBN grade affect tool life? The WBH20 CBN grade provides high abrasion resistance, which reduces flank wear during hard turning and therefore extends the useful life of the insert in demanding applications. Which geometry features improve surface finish? The combination of a Rhombic 55° shape, 7° relief and a 0.8 mm corner radius results in a more stable cutting edge and controlled chip formation, contributing to improved surface integrity on turned components. Is this insert compatible with standard toolholders? The insert’s size and form follow common indexable insert conventions; selection of an appropriate holder should be confirmed, and Metav Werkzeuge can advise on compatible clamping systems and cutting data for the DCGW11T308TM-2 WBH20. What production benefits can be expected from using this insert? Using the WBH20 CBN insert typically yields longer service intervals, greater process stability and fewer tool changes during hard machining, which together support improved throughput and reproducible quality. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and brand names belong to their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, brand-new goods from the manufacturer.
DCGW11T308TM-2 WBH20C Wendeplatten - Walter Tools
Take advantage of the combination of CBN cutting grade WBH20C and a rhombic 55° geometry for dependable hard-turning performance; order the insert directly via Metav Werkzeuge or consult the technical team for application-specific advice. DCGW11T308TM-2 WBH20C turning insert by Walter Tools — CBN grade for hard turning, rhombic 55° form DCGW11T308TM-2 WBH20C is an indexable turning insert designed for stable, long-life performance when machining hardened materials in demanding production environments. *CBN cutting grade WBH20C for hard-turning applications *7° relief angle for secure cutting engagement *Rhombic 55° insert form for versatile turning *0.8 mm corner radius for consistent edge life Predictable hard-turning with CBN for higher uptime The insert uses the WBH20C coated CBN grade, engineered for sustained performance in hard and highly abrasive materials. This results in reduced flank wear and longer intervals between tool changes, which directly improves machine uptime and lowers unit manufacturing costs. For shops processing hardened steels or pre-hardened components, the combination of a wear-resistant cutting material and robust geometry ensures repeatable part quality and a steady production flow. Geometry and edge design that control chips and surface finish A rhombic 55° shape combined with a 7° relief angle and a 0.8 mm corner radius provides a balance between cutting strength and surface integrity. The specific chipbreaker 2 profile promotes short, controllable chips in interrupted and continuous cuts, reducing the likelihood of edge build-up. These geometric choices translate into stable cutting forces and an improved surface finish on turned components, helping to meet tight tolerances with fewer reworks. Practical benefits for tool management and process security The insert is produced to tolerance class G and supplied in the Walter CBN / hard-material series, allowing consistent indexing and predictable performance across tool sets. The T3 thickness and size 11 designation suit many standard turning toolholders, facilitating quick replacement and simple inventory handling. Given its design focus on hardened and pre-hardened steels, the insert is particularly valuable for sectors where repeatability and tool life are critical, such as precision engineering and high-volume hard-machining operations. Choose the Walter Tools CBN-grade insert for reliable hard-turning — contact Metav Werkzeuge for tailored technical support and prompt procurement: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: DCGW11T308TM-2-WBH20C-WALTER Manufacturer: Walter Tools Product type: Turning insert Designation: DCGW11T308TM-2 WBH20C Series: Walter CBN / Hartstoff Facts Relief angle: 7° Corner radius: 0.8 mm Insert size: 11 Thickness: T3 Tolerance class: G Chipbreaker: 2 Insert form: Rhombic 55° Materials & features Grade: WBH20C (coated CBN) Suitable for: hardened steels Suitable for: pre-hardened steels Material code: H Application: hard turning / heavy wear conditions FAQ What materials is this insert intended for? The DCGW11T308TM-2 WBH20C insert by Walter Tools is intended primarily for hardened steels and is also suitable for pre-hardened steel applications, reflecting the CBN grade’s focus on wear resistance. How does the WBH20C grade improve tool life? WBH20C is a coated CBN cutting grade that offers superior resistance to abrasive wear, which helps the insert maintain a stable cutting edge and extends tool life in hard-turning operations. Is the insert compatible with standard toolholders? The insert’s rhombic 55° form and T3 thickness match common turning toolholder interfaces; DCGW11T308TM-2 WBH20C will fit holders designed for this insert designation, enabling straightforward replacement. What is the function of the chipbreaker 2 profile? The chipbreaker 2 geometry promotes reliable chip control and shorter chip forms, reducing chip interference and supporting consistent surface quality during both continuous and interrupted turns. Can this insert be indexed to extend usage? Yes, the insert is an indexable type produced to tolerance class G, permitting multiple indexing positions where applicable to maximise service life and maintain process stability. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany; Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCGW11T308TM-2 WBH30 Wendeplatten - Walter Tools
Take advantage of the combination of a CBN grade optimised for hard turning and a rhombic 55° geometry that enhances stability and surface finish; the robust 0.8 mm corner radius and 7° relief ensure predictable performance and reduced tool changes. Order or request cutting data via Metav Werkzeuge for fast technical support and availability. DCGW11T308TM-2 WBH30 indexable turning insert — CBN grade for hard turning (Walter Tools) The DCGW11T308TM-2 WBH30 is a rhombic 55° indexable turning insert with a CBN grade designed for hard turning of hardened steels and pre-hardened materials. CBN grade WBH30 for hard turning Rhombic 55° geometry for stable cutting 7° relief angle for consistent chip control 0.8 mm corner radius for robust edge High-performance CBN grade for demanding hard turning The core advantage of the WBH30 cutting grade is its CBN composition, developed specifically for machining hardened steels (ISO 513 group H). This mineral-based superabrasive provides exceptional wear resistance and a stable cutting edge when temperatures and contact stresses are high. For production environments where repeatability and process security matter, the insert reduces the frequency of edge changes and supports consistent part tolerances, translating into fewer interruptions and a more reliable workflow. Geometry that balances strength and surface quality The insert’s rhombic 55° form and 7° relief are chosen to combine access in tight profiles with positive chip flow. The 0.8 mm corner radius strengthens the cutting edge against chipping while helping produce a superior surface finish compared with sharper geometries. The medium-thickness T3 body gives sufficient rigidity for interrupted cuts, and the integrated chipbreaker (type 2) assists in forming short, controllable chips during hard turning—so the machining process remains stable even under elevated cutting forces. Productivity gains through repeatable performance By using a CBN solution from the Walter CBN / Hartstoff series, workshops can expect extended edge life and consistent component quality across batches. The insert’s WBH30 grade is particularly suitable when machining pre-hardened or through-hardened components, where conventional carbide would wear rapidly. The result is increased uptime, lower insert consumption per part and predictable tool-change intervals—advantages that support tighter production planning and a better return on cutting tool investment. Application guidance and compatibility The insert is specified for hard and pre-hardened steels and is intended for turning operations requiring a robust edge and reliable chip formation. The designation indicates suitability for ISO group H materials; when integrating this insert into a machining process, match the clamping and seat conditions of the toolholder to the rhombic 55° geometry and consult the manufacturer’s cutting data for feed and speed recommendations. For tailored parameter sheets or assistance selecting a compatible toolholder, contact the technical team at Metav Werkzeuge. Contact Metav Werkzeuge for application-specific cutting data, availability of Walter Tools WBH30 inserts and tailored recommendations to ensure optimal hard-turning performance Technical data SKU: DCGW11T308TM-2-WBH30-WALTER Designation: DCGW11T308TM-2 WBH30 Manufacturer: Walter Tools Series: Walter CBN / Hartstoff Core measurements Relief angle: 7° Corner radius: 0.8 mm Form: Rhombic 55° Size: 11 Thickness: T3 Tolerance class: G Chipbreaker: 2 Materials & application Grade: WBH30 (CBN) Suitable for hardened steels (ISO 513 H) Applicable to pre-hardened steel Intended for hard and wear-intensive turning tasks FAQ What materials is this insert designed for? The DCGW11T308TM-2 WBH30 insert is designed primarily for hardened steels (ISO 513 H) and is suitable for pre-hardened workpieces where a CBN grade is required. How does the CBN WBH30 grade benefit production runs? WBH30 offers extended edge life and stable wear behaviour, which helps maintain consistent part quality and reduces the frequency of insert changes during long production runs. What machining advantages does the rhombic 55° form provide? The rhombic 55° geometry enables better access to profiles and combines rigidity with a favourable cutting direction to improve surface finish and tool stability in turning operations. Is the 0.8 mm corner radius suitable for interrupted cuts? Yes, the 0.8 mm corner radius increases edge strength and is advantageous for interrupted cuts, offering improved resistance to chipping compared with smaller radii. Where can cutting data and holder recommendations be obtained? Cutting data and toolholder compatibility guidance are available from Metav Werkzeuge; consult the technical team to match the DCGW11T308TM-2 WBH30 insert to the specific turning application. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com