Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
16.78mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
The compact design and workshop-grade construction make this gauge pin a reliable choice for routine inspection and fixture set-up; its 16.78 mm nominal diameter with a 50 mm length and a close ±0.002 mm tolerance ensure consistent results on repeat measurements—order the gauge pin directly via Metav Werkzeuge or consult our specialists for tailored advice. Gauge pin M323.G78 – 16.78 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.G78 is a single precision pin for diameter verification and fixture alignment in inspection and workshop environments Precise Ø 16.78 mm nominal Compact 50 mm length for fixtures Tolerance ±0.002 mm for tight control Workshop-grade special steel construction Accuracy that stabilises process control This inspection pin delivers industrial-grade repeatability through a ±0.002 mm dimensional window, which corresponds to a deviation of just two micrometres. The closely held tolerance supports consistent go/no-go checks, in-process gauges and alignment operations, reducing scrap and rework. With a nominal Ø 16.78 mm and a 50 mm functional length, the pin is sized for compact fixtures and jigs where axial run-out and seating precision matter; the relatively low mass contributes to easy handling while maintaining the rigidity required for quick tactile gauging. Built for everyday workshop use Constructed from special steel in a workshop configuration, this single gauge pin balances corrosion resistance and wear performance for frequent use. The surface finish and material selection help maintain mating fits with bore gauges and bushings, which means fewer adjustments during production runs and less downtime for replacements. Lightweight yet robust at approximately 0.15 kg, the pin is suited to manual handling and fits common inspection trays and holders, offering a practical combination of durability and operator convenience that supports steady throughput. Practical benefits for inspection and fixture set-up As a dedicated measuring and alignment element, this gauge pin integrates easily into inspection routines and fixture checks. The nominal size and tolerance make it suitable for final-size verification and for establishing reference positions in modular tooling. Traceable identification such as the SKU and GTIN simplify inventory and quality records: the product is listed under SKU M323.G78 and GTIN 4061905069451, supporting systematic stock control. The simple geometry reduces interpretation effort during checks, enabling technicians and inspectors to focus on measurement outcomes rather than on complex set-up procedures. Discuss the workshop-grade gauge pin M323.G78 with Metav Werkzeuge for precision fixture checks or request a customised quotation through Metav Werkzeuge. Technical data Article number: M323.G78 GTIN: 4061905069451 Brand: Metav IndustryLine Facts Diameter: 16.78 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Single gauge pin design Workshop version FAQ How precise is this gauge pin for routine checks? The gauge pin M323.G78 offers a tolerance of ±0.002 mm, providing micrometre-level precision suitable for routine inspection and go/no-go verification. Is the material suitable for frequent handling and light exposure to workshop environments? Yes, the pin is made from special steel in a workshop-grade configuration, which combines wear resistance and practical durability for everyday use. Can this pin be used for fixture alignment as well as dimensional checks? The nominal Ø 16.78 mm and 50 mm length make the pin well suited to both fixture alignment and final-size verification in toolrooms and assembly jigs. What identifiers help with stock and quality management? The product is listed as SKU M323.G78 and GTIN 4061905069451, which assists with traceability and inventory control. Is this gauge pin compatible with standard bore gauges and holders? The simple cylindrical geometry and standard nominal diameter ensure compatibility with common bore gauges and fixture holders; the close tolerance supports reliable seating. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.79mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of precise diameter control (16.79 mm) and a tight tolerance of ±0.002 mm to standardise end‑of‑line inspections and reduce rework. The 50 mm length and workshop‑grade construction ensure durable handling during routine checks. Order via Metav Werkzeuge or consult the technical team for selection and supply. Gauge pin M323.G79 – single test pin, 16.79 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.G79 is a single‑piece test pin designed for rapid limit and reference checks in workshop and inspection settings. Diameter 16.79 mm ±0.002 mm accuracy 50 mm overall length for end measurements Special steel construction for workshop use Single-piece gauge pin, delivered individually Consistent, measurable accuracy that shortens inspection cycles The pin's 16.79 mm diameter combined with an accuracy of ±0.002 mm provides a reliable reference for go/no‑go checks and comparative measurements. A stable nominal size reduces variation between successive measurements and simplifies decision rules during quality control. Using a defined hardened reference in inspection routines makes tolerance assessments reproducible and speeds up throughput by lowering the need for repeat checks. Robust workshop design for everyday handling Manufactured from special steel and specified as a workshop version, the pin tolerates frequent handling and the knocks associated with shop‑floor use. The 50 mm length offers good engagement for end measurements without excess overhang, improving handling safety and repeatability. The single‑piece design removes joint‑related uncertainties, making it suitable as a fixed reference in fixtures and manual gauging tasks. Practical integration into inspection workflows The item is supplied individually for straightforward inventory control and quick access during batch inspections. As a simple mechanical reference, the test pin integrates directly into visual and tactile inspection processes, complementing digital gauges or calipers where a hard physical limit is required. Clear labelling and the compact form factor support portable measurement kits and mobile quality checks across multiple production points. For procurement or technical clarification regarding the Metav IndustryLine gauge pin M323.G79, please contact Metav Werkzeuge GmbH in Emmerich via info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss fitment and delivery options. Technical data SKU: M323.G79 GTIN: 4061905069468 Name: Gauge pin, single, 16.79 mm, length 50 mm Weight: 0.15 kg Material: Special steel Facts Diameter: 16.79 mm Length: 50 mm Accuracy: ±0.002 mm Mass: 0.15 kg Special features Workshop version Single-piece delivery Application: end gauge / reference pin Supplied individually FAQ What are the main dimensions and tolerance of this gauge pin? The gauge pin M323.G79 from Metav IndustryLine has a diameter of 16.79 mm, an overall length of 50 mm and a tolerance of ±0.002 mm. Can this pin be used as a fixed reference in a fixture? Yes, the single‑piece construction and workshop‑grade special steel make the gauge pin suitable for use as a fixed reference in fixtures and manual gauging operations. Is the item supplied individually or as a set? This product is supplied individually; the M323.G79 is delivered as a single test pin for immediate use or inventory stocking. Which applications suit this test pin best? Typical applications include go/no‑go checks, end‑of‑line limit inspections, reference measurements and incorporation into portable measurement kits. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.81mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the precise combination of a 16.81 mm measuring diameter, workshop-grade special steel construction and a tight ±0.002 mm tolerance for reliable end‑measurement checks; order the item directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.G81 — single precision pin, 16.81 mm Ø, 50 mm length (Metav IndustryLine) Gauge pin M323.G81 is a single measuring pin designed for end‑dimension checks and simple go/no‑go gauging in workshop environments Workshop execution for routine use Diameter 16.81 mm for accurate fits Length 50 mm for stable handling Special steel construction for wear resistance Precise dimensional control for routine inspection The M323.G81 gauge pin delivers a defined measuring diameter of 16.81 mm with a verified positional accuracy of ±0.002 mm, supporting repeatable end‑measurement work. This level of precision makes the pin suitable for quick verification tasks where dimensional conformity is critical and where small deviations can lead to assembly issues. The clear numerical tolerance offers a rational basis for quality decisions and reduces the need for repeated measuring cycles, increasing throughput in standard inspection procedures. Robust material and compact handling for daily use Manufactured from special steel, the pin combines surface hardness and dimensional stability that are useful for workshop demands. The 50 mm overall length and compact mass (0.15 kg) make the pin easy to position and manoeuvre in fixtures or in handheld checks, reducing handling time and operator fatigue. The workshop design emphasises durability under frequent use while maintaining the precise diameter needed for fitting checks and end‑mass measurements. Practical application in production and test benches This single gauge pin is intended for straightforward end‑measurement and dimensional verification tasks, for instance checking bore seating or verifying mating part diameters during incoming inspection. As a single‑element tool it integrates easily into existing gauging routines and jigs; traceable identification supports inventory and process control. The clear specification and sturdy design deliver an efficient balance of accuracy and operational convenience for everyday metrology needs. For reliable dimensional checks, procure the Metav IndustryLine gauge pin M323.G81 from Metav Werkzeuge in Emmerich or contact our team for guidance on integration into existing inspection routines. Technical data Article number: M323.G81 GTIN: 4061905069482 Label: Gauge pin, single, 16.81 mm diameter, 50 mm length Manufacturer: Metav IndustryLine Facts Diameter: 16.81 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Intended use: End measurements / dimensional checks Story trigger: end measurements FAQ What materials is the pin made from? The gauge pin is produced in special steel, which gives the pin good wear resistance and dimensional stability suitable for workshop inspection tools. How precise is the measuring diameter of this pin? The specified measuring diameter is 16.81 mm with an accuracy of ±0.002 mm, making it suitable for fine verification tasks and repeatable end‑measurements. Can this pin be used for checking bore seats and mating parts? Yes, the single gauge pin is intended for end‑measurement and dimensional verification of bore seats and mating diameters in production and incoming inspection. Is this item identified for stock and traceability? The product is listed as M323.G81 (GTIN 4061905069482), which facilitates inventory tracking and process documentation. Is the M323.G81 suitable for workshop daily use? Designed as a workshop execution, the M323.G81 combines a compact length and robust material for frequent handling and routine inspection work. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.82mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Taking advantage of the precise Ø 16.82 mm diameter, the robust 50 mm length and the workshop-grade construction ensures reliable plug‑gauge measurements in production and inspection settings; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single, 16.82 mm Ø, length 50 mm (M323.G82) — Metav IndustryLine, special steel, ±0.002 mm Gauge pin, single, 16.82 mm Ø, length 50 mm is a hardened inspection pin intended for end‑size checks, alignment and go/no‑go fits in workshop and production environments Workshop‑grade special steel construction Diameter precisely 16.82 mm for end‑size checks Length 50 mm for robust handling and reach Manufacturing tolerance ±0.002 mm for fine control Delivered in a transport case for secure handling Accurate end‑size checks with a compact gauge pin The compact inspection pin offers a precise Ø 16.82 mm reference for go/no‑go and alignment checks in machining and assembly tasks. Its ±0.002 mm manufacturing tolerance provides a measurable basis for repeatable acceptance decisions; this level of precision suits fine mechanical assemblies where small deviations affect fit. The solid construction minimises elastic deformation during insertion, so readings remain consistent even under frequent use. The design concentrates on one essential benefit: a compact, reproducible reference dimension that integrates into existing inspection routines without additional fixtures. Workshop durability and handling benefit production flow Constructed from special steel and supplied as a single hardened pin, this tool combines wear resistance with easy handling. The 50 mm length gives sufficient engagement depth for most end‑size verifications while keeping the pin short enough to avoid bending moments that can bias results. The workshop version specification emphasises a balance between daily robustness and dimensional fidelity, making the item suitable for bench inspection, quick in‑process checks and fixture validation. Stored and transported in a protective case, the pin arrives ready for use and remains secure between operations. Integration into inspection processes and traceability As a standard inspection artefact, the pin supports straightforward comparison checks and can be included in control plans as a fixed reference size. The clear item identification (M323.G82) and the GTIN facilitate inventory management and traceability inside quality systems. For users without advanced metrology backgrounds: a gauge pin provides a known diameter to verify mating holes or bores quickly — if the pin passes, the part meets the intended dimension within the pin’s tolerance. This direct approach accelerates decision making on the shop floor and reduces downtime caused by uncertainty. Contact Metav Werkzeuge for tailored advice on Metav IndustryLine gauge pins — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitability and ordering options Technical data Article number: M323.G82 GTIN: 4061905069499 Material: Special steel Net weight: 0.15 kg Facts Diameter: 16.82 mm Length: 50 mm Manufacturing tolerance: ±0.002 mm Special features Workshop version Single gauge pin delivery Supplied in transport case Category: Gauge pin / inspection pin FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.G82 is manufactured to a tolerance of ±0.002 mm, providing fine control for end‑size verification and go/no‑go assessments. Is the pin suitable for routine shop‑floor checks? Yes. The workshop‑grade construction and 50 mm length make the pin suitable for routine in‑process and bench inspection tasks in metalworking environments. Does the product come with a protective case? The gauge pin is supplied in a transport case to protect the reference surface during storage and transfer. Can this pin be used to check holes and bores? The M323.G82 gauge pin is intended for end‑size checks and alignment of bores or mating parts where a precise Ø 16.82 mm reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.83mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of shop-grade robustness, pinpoint ±0.002 mm accuracy and a compact 16.83 mm reference diameter to achieve repeatable fixturing and inspection results. Order the gauge pin directly via Metav Werkzeuge or consult the technical team for application-specific advice. Gauge Pin, single, 16.83 mm diameter — 50 mm length (Metav IndustryLine) A gauge pin, single, 16.83 mm diameter, 50 mm length engineered for repeatable reference and inspection tasks in workshop and production settings. Workshop version for robust daily use Diameter 16.83 mm with ±0.002 mm tolerance Length 50 mm for consistent reference points Made from special steel for long service life Precision that stabilises measurement routines The core advantage of this pin is its ±0.002 mm manufacturing tolerance, which translates into reliable repeatability when used as a reference or datum in fixtures and gauges. Such a tight tolerance reduces setup variation and shortens inspection cycles, enabling faster decision-making on the shop floor. The nominal 16.83 mm diameter is presented as a true reference size, suitable for bore checks, plug-fit tests and alignment tasks; in practice, consistent diameters minimise rework and help safeguard process capability. Built for workshop durability and predictable handling Constructed from special steel, the pin combines wear resistance with a smooth, consistent surface finish that supports frequent insertion and withdrawal without rapid degradation. The 50 mm length provides a convenient working overlap for secure seating in fixtures while remaining compact enough for easy handling and storage. As a workshop version, the design favours robustness and long service life over delicate lab-only finishes — a practical balance that keeps downtime low and maintenance straightforward. Integrates cleanly into inspection workflows and tooling This single gauge pin is an efficient component for modular inspection setups, acting as a datum for go/no‑go assemblies, alignment checks and repeatable runouts. Traceability is supported via the SKU M323.G83 and GTIN 4061905069505, making inventory and audit processes more transparent. For users unsure about suitability in a specific jig or fixture, Metav Werkzeuge’s technical advisors can provide guidance on integration and complementary tooling, ensuring the pin delivers measurable improvements in throughput and quality control. For workshop-ready accuracy and dependable supply, contact Metav Werkzeuge to discuss the M323.G83 gauge pin and options for immediate procurement or technical consultation. Technical data Article number: M323.G83 GTIN: 4061905069505 Label: Prüfstift, einzeln, 16,83 mm Länge 50 mm Eclass: 21170231 Facts Diameter: 16.83 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop version SKU: M323.G83 FAQ What is the intended use for this gauge pin? The gauge pin M323.G83 from Metav IndustryLine is designed as a repeatable reference for fixture alignment, bore checking and plug-fit verification in workshop and production environments. How precise is the diameter of the pin? The diameter is manufactured to ±0.002 mm, offering the repeatability required for reliable go/no‑go and datum applications. Is the pin suitable for frequent shop-floor use? Yes; the workshop version and special steel construction of the M323.G83 make it suitable for frequent insertion and withdrawal typical of production and maintenance tasks. What information helps with traceability and procurement? Use SKU M323.G83 and GTIN 4061905069505 for ordering and inventory tracking; Metav Werkzeuge can advise on delivery times and compatible fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.84mm Test Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of precise workshop measurement with a robust special‑steel construction and a tight tolerance of ±0.002 mm; the compact 16.84 mm diameter and 50 mm length keep handling simple while ensuring repeatable end‑measures. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for integration advice. Gauge pin, single — 16.84 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin (16.84 mm, 50 mm) designed for accurate end‑measurement and inspection tasks in workshop environments Workshop version, robust construction Diameter 16.84 mm, length 50 mm Tolerance ±0.002 mm for high precision Delivered in protective transport case Precision that supports reliable inspection The gauge pin delivers a measurable advantage where small tolerances matter: with a declared tolerance of ±0.002 mm, it is intended for tasks that require consistent end‑measure checks and tight fit verification. The finely controlled diameter minimizes measurement scatter and enables reliable comparison against finish limits or mating bores. Such precision supports faster decision‑making in inspection workflows and reduces rework caused by ambiguous fits. Compact form for efficient workshop handling Classified in the micro range, the compact 16.84 mm diameter and 50 mm overall length combine reach with low mass for convenient single‑hand handling. The short, stiff geometry reduces bending and makes the pin well suited for small fixtures, jigs and spot checks on components where accessibility is limited. The modest weight of 0.15 kg contributes to safe, repeatable placement during sequential checks. Built for workshop use and transport protection Supplied as a workshop version, the pin is manufactured from special steel, giving it mechanical robustness under frequent use. Delivery in a protective transport case safeguards the measuring surface during storage and transit, preserving the functional surface for longer service life. The construction emphasises durability without compromising on the geometric precision required for end‑measure verification. Practical applications and handling benefits This single gauge pin is suitable for routine end‑measure inspections, plug and bore checking, and use as a reference element in simple inspection fixtures. The compact diameter and short length make it appropriate for small‑part assembly lines, toolroom checks and maintenance departments where quick, reproducible measurements are needed. The clear, standard geometry simplifies integration into existing quality procedures while the robust finish reduces the frequency of replacement. Contact Metav Werkzeuge to discuss how the Metav IndustryLine gauge pin M323.G84 can be specified for inspection jigs or small‑part verification and to arrange delivery from our Emmerich stock. Technical data Article number: M323.G84 GTIN: 4061905069512 Label: Gauge pin, single, 16.84 mm, length 50 mm Facts Diameter: 16.84 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Material: Special steel Workshop version Delivered in protective transport case FAQ What is the precise diameter and length of the gauge pin? The gauge pin M323.G84 has a diameter of 16.84 mm and a length of 50 mm. What tolerance can be expected from this gauge pin? The Metav IndustryLine gauge pin is specified with a tolerance of ±0.002 mm for accurate end‑measure checks. Is the surface material suitable for frequent workshop use? Yes, the pin is made from special steel and supplied in a workshop version intended for regular use. Does the product include protective packaging for transport? Delivery includes a protective transport case to preserve the measuring surface during storage and transit. Is a calibration certificate supplied with the gauge pin? A calibration certificate is not specified for this item; specific calibration options can be discussed with Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.85mm Gauge Pin 50mm Length Workshop Version, ±0.002 Accuracy - Metav IndustryLine
Take advantage of a compact, workshop‑grade gauge pin that combines tight dimensional control and robust construction: the 16.85 mm nominal diameter with a ±0.002 mm tolerance and a 50 mm length ensures repeatable end‑measure checks and simple fixture referencing. Order the part directly via Metav Werkzeuge or contact our consultants for fitting and application advice. Gauge pin, single — 16.85 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin 16.85 mm × 50 mm serves as a precise reference for end‑measure inspections and layout tasks in production, assembly and quality control environments Workshop design for robust use Diameter 16.85 mm, tight tolerance ±0.002 50 mm length for compact inspection gauges Made from special steel for long service life Repeatable measurements for quality control The plug is engineered for repeatable accuracy in end‑measure tasks where small deviations matter. With a nominal diameter of 16.85 mm and a declared variation of ±0.002 mm, the component provides a reliable reference for bore checks, go/no‑go fixtures and alignment procedures. The compact 50 mm shank minimises lever arm effects during insertion, reducing measurement variance and helping to maintain process stability on the shop floor. Built to withstand workshop conditions Produced in a workshop version and machined from special steel, this pin is designed for everyday industrial use without sacrificing dimensional integrity. The material choice balances hardness and toughness so the gauge resists wear during repeated seating and extraction cycles, extending service life and reducing replacement frequency. The modest mass and compact form make the item easy to handle and integrate into clamping or checking setups. Practical integration and traceable results As a straightforward end‑measure reference, the pin simplifies set‑up routines and inspection sequences: it fits inspection plates, fixture bores and test rigs where a precise datum is required. Traceability is supported by the clear specification of diameter and tolerance, enabling straightforward documentation within quality records and measurement plans. For applications that demand consistency across batches, this reference element reduces rework and supports efficient quality throughput. Contact Metav Werkzeuge for specification matching and supply of the Metav IndustryLine gauge pin; the Emmerich team will advise on compatibility with existing fixtures and delivery options. Technical data Article number: M323.G85 GTIN: 4061905069529 Label: Prüfstift, einzeln, 16,85 mm Länge 50 mm Numeric data Nominal diameter: 16.85 mm Length: 50 mm Tolerance/variation: ±0.002 mm Weight: 0.15 kg Materials & features Material: special steel Version: workshop execution Application: end‑measure / reference pin FAQ What is the declared tolerance of this gauge pin? The declared variation for the gauge pin is ±0.002 mm, suitable for precise end‑measure checks and inspection referencing. Which applications is the pin intended for? The pin is intended for end‑measure inspections, bore referencing and fixture set‑up in production and quality control contexts. What material is the gauge pin made from? This Metav IndustryLine gauge pin is machined from special steel chosen for its wear resistance and workshop durability. Is this pin compatible with standard inspection plates? Yes, the 16.85 mm nominal diameter and compact 50 mm length make the pin compatible with standard test plates and bespoke fixtures used for reference and alignment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.86mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
High-precision inspection and durable workshop use are combined in this gauge pin: 16.86 mm diameter with a verified ±0.002 mm tolerance and a 50 mm functional length, supplied ready for safe transport and immediate use; order the item directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.G86 — 16.86 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.G86 — a single test pin for precise end‑size checks and Go/No‑Go verifications in routine workshop inspection and fixture setting Workshop version for robust use Diameter 16.86 mm for precise fit Accuracy ±0.002 mm tolerance Supplied in protective transport case Reliable tolerance for repeatable checks A small inspection instrument can determine whether a part meets specification; the gauge pin accomplishes that with measurable certainty. With a nominal diameter of 16.86 mm and a declared tolerance of ±0.002 mm, the pin provides a clearly defined pass/fail reference for bore and hole checks. The quoted tolerance reflects manufacturing control and allows traceable acceptance limits to be set in production documentation. Using a fixed‑size metal pin reduces operator variance compared with subjective gauges and helps maintain consistent in‑process control. Built for workshop handling and longevity The workshop execution is designed to tolerate everyday handling while preserving dimensional stability. Manufactured from special steel, the pin resists deformation during repeated seating and can be used as a setting reference for fixtures or as a mating gauge for plugs and bores. The 50 mm length ensures sufficient engagement for stable measurement without excessive overhang, while a compact mass (approximately 0.15 kg) supports easy handling and fast changeovers at the inspection bench. The item is supplied in a protective transport case to prevent surface damage during storage and transit. Practical integration into inspection workflows Integration into quality routines is straightforward: the pin serves as a direct reference when calibrating comparators, checking bore gauges, or performing assembly trials. Its simple geometry means no special training is required; the hard reference point simplifies setup procedures and reduces cycle time for repetitive checks. For documentation and procurement, the article is listed as SKU M323.G86 and can be referenced in QA protocols and parts lists to ensure consistent replacement and traceability. Contact Metav Werkzeuge for availability and specification support on the Metav IndustryLine gauge pin M323.G86; our Emmerich team can advise on suitability for particular inspection tasks and arrange prompt delivery Technical data SKU: M323.G86 GTIN: 4061905069970 Category: Messstifte Facts Diameter: 16.86 mm Functional length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop execution Supplied in protective transport case Single test pin for end‑size checks FAQ What tolerance does this pin offer for inspection tasks? The gauge pin is manufactured to a tolerance of ±0.002 mm, making it suitable for precise go/no‑go and end‑size verifications with clearly defined acceptance limits. Can the pin be used to set fixtures and gauges? Yes. The M323.G86 gauge pin is suitable for fixture setting and for establishing reference sizes when calibrating comparators and bore gauges. What material is the pin made from and how does that affect wear? The pin is made from special steel, chosen to provide good wear resistance and dimensional stability under normal workshop use. Is the pin delivered ready for storage and transport? The pin is supplied in a protective transport case to prevent surface damage during storage and shipment. How should the pin be referenced in quality documentation? Use the SKU M323.G86 and the GTIN 4061905069970 when listing the gauge pin in procurement records and QA protocols for traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.87mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, special steel construction, and high dimensional accuracy (±0.002 mm) for dependable end‑dimension checks; order directly via Metav Werkzeuge or consult our specialists for application advice. M323.G87 Gauge pin — 16.87 mm Ø, 50 mm length (Metav IndustryLine) The M323.G87 gauge pin is a single inspection pin designed for precise end‑dimension verification in workshop metrology. Workshop version for robust daily use Special steel for long service life Dimensional accuracy ±0.002 mm Supplied in a protective case Consistent accuracy for tight production tolerances The inspection pin provides a guaranteed dimensional accuracy of ±0.002 mm, which makes it suitable where repeatability matters most. Built for checks that determine final part fit and end‑dimensions, this component supports clear pass/fail decisions and helps to reduce rework and scrap rates. Classified in the micro measurement range (10–100 mm), the format combines a compact profile with the stiffness needed to keep measurements stable during manual handling, so measurement uncertainty is kept low and results remain reproducible. Robust construction for everyday workshop use Manufactured from special steel and offered in a workshop execution, the pin resists the knocks and handling typical of production environments. At 50 mm overall length and a nominal diameter of 16.87 mm, the format is easy to position in fixtures and jigs while remaining rigid enough for reliable contact measurement. The single‑piece design minimises interfaces that can introduce error, and the component is supplied in a protective case for secure transport and storage, keeping the measuring surface in good condition between uses. Simple integration into inspection routines As a compact gauge pin, the unit is intended for end‑dimension testing, plug gauges and checking bores or mating parts where a precise master diameter is required. The small footprint makes it convenient to use in bench‑level inspection, assembly verification or as a reference plug for go/no‑go checks. Traced by SKU M323.G87, the part is straightforward to catalogue into inventory systems and to specify on inspection sheets; the clear numerical tolerance and physical dimensions ensure unambiguous communication across procurement and quality teams. Contact Metav Werkzeuge for tailored advice on integrating the M323.G87 into existing inspection jigs or for ordering information — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.G87 GTIN: 4061905069987 Name: Gauge pin, single, 16.87 mm Ø, 50 mm length Category: Gauge pins ECLASS: 21170231 Core technical figures Diameter: 16.87 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Materials & features Material: Special steel Workshop execution Supplied in protective case FAQ What are the exact dimensions of this inspection pin? The inspection pin has a nominal diameter of 16.87 mm and an overall length of 50 mm; weight is 0.15 kg (SKU M323.G87, Metav IndustryLine). What tolerance and repeatability can be expected? The pin is specified with a dimensional accuracy of ±0.002 mm, offering high repeatability for end‑dimension checks in micro‑range applications. Which applications suit this gauge pin best? This format is ideal for end‑dimension verification, plug checks and small‑bore inspection tasks in workshop metrology where compact, rigid masters are required. What material is used and how robust is the design? Manufactured from special steel in a workshop execution, the component is designed for daily use and handling in production environments. How is the part delivered for transport and storage? The gauge pin is supplied in a protective case to preserve the measuring surfaces during transport and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.88mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of a compact, workshop-ready gauge pin that combines high dimensional precision (±0.002 mm), hardened special steel construction and a practical 50 mm working length for repeatable reference measurements; order the gauge pin directly via Metav Werkzeuge or ask the consultants if additional specifications are required. Gauge pin M323.G88 — precision gauge pin, Ø 16.88 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.G88 is a hardened, single-purpose gauge pin for dimensional verification and assembly checking in workshop and quality-control environments Workshop-grade construction Diameter 16.88 mm precision Tolerance ±0.002 mm Supplied in transport box Consistent accuracy for routine inspection The M323.G88 functions as a stable reference for go/no-go checks and setting operations, delivering repeatable results thanks to a verified tolerance of ±0.002 mm. Manufactured from special steel, the pin combines surface hardness with dimensional stability to resist wear during frequent use. This reliability reduces rework and speeds up inspection loops, making the component a practical choice for production lines and bench testing where consistent outcomes matter. Compact dimensions for ergonomic handling With a nominal diameter of 16.88 mm and an overall length of 50 mm, this gauge pin occupies a middle-ground size that is easy to handle while still providing sufficient engagement for accurate measurements. The short, robust geometry minimises bending and ensures positional stability when inserted into bores or used as a reference dowel. The workshop-focused design streamlines handling on the shop floor and contributes to faster, safer checks without complex fixturing. Materials and transport-ready packaging Constructed from special steel, the pin is designed to withstand the mechanical demands of everyday metrology tasks. Delivery in a transport box protects the finished surface and dimensions during storage and movement, preserving calibration and prolonging service life. The boxed supply is particularly useful for workshop logistics and tool sets where protection during transit is essential. How this gauge pin integrates into inspection workflows The compact gauge pin serves as a simple but effective tool for dimensional verification, setting gauges and alignment tasks. Its precise diameter makes it a dependable reference for plug gauge comparisons and fixture alignment. Where traceable documentation is required for quality control processes, the product data and supplied condition provide a clear baseline for internal documentation and process control. For a direct consultation on suitability for specific inspection tasks or to arrange procurement via Metav Werkzeuge, please contact our team in Emmerich for precise delivery and handling options Technical data SKU: M323.G88 GTIN: 4061905070495 Label: Gauge pin, single, 16.88 mm, length 50 mm Facts Diameter: 16.88 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop-version construction Supplied in a transport box Category: gauge pins FAQ What is the intended use for this gauge pin? The gauge pin M323.G88 is intended for dimensional verification, plug gauge checks and fixture alignment in workshop and inspection environments. Is the diameter tolerance suitable for precision inspection tasks? Yes; the M323.G88 is specified with a tolerance of ±0.002 mm, making it appropriate for many routine precision inspection tasks and reference checks. What material is the pin made from and how does that affect wear? The pin is made from special steel, offering a balance of hardness and durability that helps maintain dimensional stability under frequent use. Does the product arrive protected for transport and storage? The M323.G88 is supplied in a transport box to protect the surface and dimensions during handling and storage. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.89mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Benefit from workshop‑grade precision, a nominal diameter of 16.89 mm and a tight ±0.002 mm tolerance for dependable end‑dimension checks; the robust special steel construction and compact 50 mm length support repeatable inspection results in production. Order the gauge pin directly via Metav Werkzeuge or consult the advisory team for application support. Gauge pin, single — 16.89 mm Ø, 50 mm length (Metav IndustryLine) The Gauge pin, single, 16.89 mm is a workshop‑grade inspection pin designed for end‑dimension verification and go/no‑go fits in machine shops and inspection benches. Workshop‑grade execution Diameter 16.89 mm precise fit Length 50 mm for end‑dimension checks Tolerance ±0.002 mm high accuracy Precise control where tolerances matter This inspection pin delivers repeatable measurement performance thanks to a nominal diameter of 16.89 mm and a documented tolerance of ±0.002 mm. As a hardened, single‑piece gauge it provides a reliable datum for go/no‑go verification and fit checks, reducing the risk of assembly errors and rework. The measured accuracy supports quality gates on the shop floor and contributes directly to production yield improvements through fewer false rejects. Durable workshop design for everyday use Manufactured in special steel and specified as a workshop execution, the pin balances wear resistance with manageable handling for routine inspection tasks. The 50 mm length offers a useful contact area for end‑dimension control and fixture use while keeping the tool compact for bench and fixture integration. The construction minimizes surface deformation over repeated cycles, ensuring consistent contact geometry and extending service life under normal workshop conditions. Practical integration into inspection workflows Offered as a single inspection pin, this item is suited to dedicated testing jigs, plug checks and quick in‑process controls. Traceability is supported via the SKU and GTIN, which facilitate inventory and quality records for production tracking. Backed by Metav IndustryLine quality assurance, the pin serves as a straightforward, low‑complexity solution where a stable reference diameter is required, enabling efficient inspection routines without complex set‑ups. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine gauge pin M323.G89 can be integrated into existing inspection processes; Metav Werkzeuge in Emmerich provides technical advice and rapid supply for industrial needs. Technical Data Article number / SKU: M323.G89 GTIN: 4061905070501 Brand: Metav IndustryLine Category: Gauge pins / inspection pins Facts Diameter: 16.89 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Execution: workshop grade Delivery: single unit Application: end‑dimension checks and fit verification FAQ What tolerance does the gauge pin have? The Gauge pin, single, 16.89 mm (Metav IndustryLine, SKU M323.G89) is specified with a tolerance of ±0.002 mm, suitable for high‑precision fit checks. Which materials is the pin suitable for checking? The pin itself is made from special steel and is intended as a dimensional reference for components made from a wide range of materials when performing go/no‑go or end‑dimension verifications. Is this pin supplied as a single item or in sets? This article is supplied as a single unit (single gauge pin), intended for integration into inspection fixtures or for standalone use in the workshop. Can the pin be used in fixture and jig applications? Yes, the compact 50 mm length and workshop execution make it suitable for use in jigs, fixtures and bench checks where a stable reference diameter is required. How is traceability handled for this product? Traceability can be maintained via the SKU M323.G89 and GTIN 4061905070501, which support inventory and quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.8mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of workshop‑grade robustness combined with ±0.002 mm repeatability and a compact 50 mm length for reliable end‑measure checks; order the component via Metav Werkzeuge or consult our specialists for application advice. Test pin, single, 16.8 mm × 50 mm (Metav IndustryLine) Test pin, single, 16.8 mm × 50 mm is a workshop‑grade gauge pin designed for precise end‑measure and fit checks in production, maintenance and assembly environments Workshop‑grade special steel construction Precision fit at 16.8 mm diameter 50 mm length for reach in fixtures High repeatability with ±0.002 mm accuracy Precision where it matters The compact gauge pin delivers high repeatability thanks to a verified runout tolerance of ±0.002 mm, which stabilises measurement variance across repeated checks. Manufactured from special steel in a workshop execution, the pin resists wear under frequent handling and contact with mating components. This combination reduces rework and inspection time and supports consistent process control in routine quality checks. Designed for fine mechanical and fixture work Classed in the micro range (measuring range up to 100 mm), the pin is optimised for small‑format applications where a tight fit and exacting surface condition matter. The 16.8 mm diameter provides a defined reference for bore and seating inspections, while the 50 mm length reaches into deeper seats and fixturing pockets without compromising stiffness. For jigs, gauges and maintenance checks this geometry simplifies alignment and speeds up tactile verification. Practical handling and workshop integration Supplied as a single unit for flexible use in fixture assemblies, the pin combines a compact form (weight approx. 0.15 kg) with a robust finish suitable for frequent handling. The hardened construction maintains dimensional stability under repeated insertion and withdrawal, improving long‑term measurement confidence. Traceable identification and compact dimensions ease storage and mounting in common gauge holders or bespoke fixtures, making the item straightforward to integrate into existing inspection routines. Choose the Metav IndustryLine workshop test pin for reliable ±0.002 mm performance — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 to confirm fit and application Technical data Article number: M323.G80 GTIN: 4061905069475 Label: Prüfstift, einzeln, 16,8 mm Länge 50 mm Facts Diameter: 16.8 mm Length: 50 mm Weight: 0.15 kg Accuracy / runout: ±0.002 mm Special features Material: Special steel Version: Workshop execution Supplied: single unit Eclass: 21170231 FAQ What is the intended use of this test pin? The test pin M323.G80 is intended for end‑measure and fit checks in production and maintenance; it provides a defined reference diameter for bore and seating inspections. How precise is the gauge pin? The component achieves a runout tolerance of ±0.002 mm, delivering the repeatability required for reliable routine checks. Which materials is the pin suitable for interfacing with? Made from special steel, the pin is designed for contact with typical metal fixture components and mating bores encountered in workshop and assembly environments. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.91mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
High-precision end‑dimension checks are made reliable by the combination of a 16.91 mm nominal diameter, a ±0.002 mm tolerance and a robust 50 mm length in a workshop‑grade special‑steel construction. Order the gauge pin directly from Metav Werkzeuge or consult the technical team for application advice. Gauge pin M323.G91 – 16.91 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.G91 is a single workshop‑grade test pin designed for precise end‑dimension verification and reference measurements in assembly, inspection and fixture set‑up. High precision: ±0.002 mm tolerance Precision diameter 16.91 mm for end‑dimension checks Workshop‑grade special steel, 50 mm overall length Reliable checks with measurable precision The gauge is specified with a ±0.002 mm tolerance, which places it in the high‑precision class for test pins and makes it suitable for repeatable end‑dimension verification. The 16.91 mm nominal diameter is intended as a reference size for plug‑type measurements and can be used to confirm bore diameters, positioning bores or part interfaces where tight dimensional control is required. In practice, the tight tolerance reduces uncertainty in pass/fail decisions and supports consistent quality documentation during production and incoming inspection. Robust workshop design that eases handling Constructed from special steel in a workshop‑oriented design, the pin balances durability with ease of handling. The 50 mm overall length provides sufficient grip for manual positioning while keeping bending and handling errors low during single‑operator measurement tasks. The moderate mass (0.15 kg) contributes to stable placement without being cumbersome in routine use. The workshop specification indicates a focus on everyday reliability rather than delicate laboratory-only handling, which suits maintenance bays, toolrooms and production lines. Practical use in quality workflows Integration into existing workflows is straightforward: the test pin serves as a fixed‑dimension reference for quick go/no‑go checks, fixture set‑up, and comparative measurements against master gauges. Identification via SKU and GTIN simplifies inventory and traceability; the compact geometry permits easy storage with other inspection tools. Using a dedicated gauge like this reduces rework and shortens inspection times because measurements are direct and unambiguous. Secure workshop‑grade measurement reliability with Metav IndustryLine — contact Metav Werkzeuge for application advice and reliable supply from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: M323.G91 GTIN: 4061905070525 Label: Test pin, single, 16.91 mm diameter, 50 mm length Manufacturer: Metav IndustryLine Facts Diameter: 16.91 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version ECLASS: 21170231 FAQ What nominal diameter does the pin have? The nominal diameter is 16.91 mm for the M323.G91 gauge pin. What tolerance can be expected from this gauge pin? The pin is specified with a tolerance of ±0.002 mm, suitable for high‑precision end‑dimension checks. What material is used and how does it affect durability? The pin is made from special steel; this workshop‑grade material is chosen for wear resistance and robust everyday use. Is the gauge suitable for fixture and assembly set‑up? Yes — the 50 mm length and precise diameter make the pin appropriate for fixture alignment, positioning bores and quick reference checks in assembly work. Which identifiers assist ordering and traceability? Order and stock via SKU M323.G91; GTIN for logistics is 4061905070525. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.92mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of robust workshop construction and high measurement fidelity: the single gauge pin delivers Ø 16.92 mm nominal diameter, 50 mm length and a tight ±0.002 mm tolerance for reliable end‑measure verification. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for technical advice. M323.G92 Gauge pin – Ø 16.92 mm, length 50 mm (Metav IndustryLine) The M323.G92 gauge pin is a single, workshop‑grade inspection pin designed for precise end‑measure checks and compact component verification in small‑part environments. Workshop version, robust construction Diameter Ø 16.92 mm for end‑measure checks Length 50 mm, compact handling High repeatability with ±0.002 mm tolerance Precision where small dimensions matter The inspection pin is designed for applications in the micro range (max. measurand up to 100 mm), where compact size must be paired with exactness. With a nominal Ø 16.92 mm and a specified ±0.002 mm variation, this gauge provides repeatable reference geometry for incoming inspection, final checks and setting tasks. The close tolerance reduces uncertainty in pass/fail decisions and supports efficient quality control workflows by lowering the risk of rework. Durable design tuned to workshop use Constructed from Special steel and specified as a workshop version, the pin resists routine handling stresses common in production environments. The 50 mm length keeps the probe easy to position in confined fixtures while offering sufficient engagement for stable readings. The simple, single‑piece format minimises moving parts, which benefits long‑term stability and reduces maintenance demands compared with adjustable gauges. Practical integration and handling benefits As a dedicated end‑measure tool, the pin is suitable for quick verification of bore sizes, gauge blocks and jig references. Its modest mass and short overall length permit single‑hand placement in assembly or measuring jigs, improving throughput on repetitive checks. Where traceable documentation or specialised calibration is required, Metav’s product portfolio and advisory service can help match the pin to an appropriate calibration regime and measurement routine. For purchases or detailed specification matching, contact Metav Werkzeuge — Metav IndustryLine specialists are available to advise on suitability, calibration options and batch supply for production use. Technical data Article number: M323.G92 GTIN: 4061905070532 Brand: Metav IndustryLine Dimensions & accuracy Diameter: 16.92 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Materials & features Material: Special steel Version: Workshop execution Application: End‑measure checks Category: Gauge pin / inspection pin FAQ What is the primary application of this gauge pin? The M323.G92 gauge pin from Metav IndustryLine is intended for end‑measure verification and compact component checks where a precise reference diameter is required. What tolerance and repeatability can be expected? The gauge pin is specified with a tolerance of ±0.002 mm, delivering high repeatability suitable for fine inspection and control tasks. Which material is used for the pin? The pin is manufactured from Special steel in a workshop version to balance wear resistance with handling robustness. Is the pin supplied as a single item or in sets? This entry refers to a single gauge pin (M323.G92); multiple items can be ordered separately to form custom sets if required. Can the gauge pin be used in fixture and jig checking? Yes, the compact 50 mm length and rigid single‑piece design make it suitable for use in jigs, fixtures and quick inspection stations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.93mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a compact, workshop‑ready gauge pin that combines high positional accuracy and robust special‑steel construction for reliable fit checks and end‑measurements; order the single gauge pin directly via Metav Werkzeuge or contact our consultants for application support. Gauge pin M323.G93 — single gauge pin, Ø 16.93 mm, length 50 mm (Metav IndustryLine) Gauge pin M323.G93 for precise fit checks and end‑measurements in workshop and production environments, offering a compact form and workshop specification for routine inspection tasks Single gauge pin Ø 16.93 mm Length 50 mm for compact checks Made from special steel High accuracy ±0.002 mm Precision that keeps production moving The gauge pin M323.G93 is manufactured for repeatable dimensional control where tight tolerances matter. With an indicated accuracy of ±0.002 mm, the pin supports consistent verification of bores, dowel fits and mating parts, reducing the risk of assembly faults and costly rework. The use of special steel provides the necessary surface integrity for frequent contact inspections, while the compact geometry minimises handling time during serial checks. Compact design for tight access and reliable handling A compact overall length of 50 mm and a nominal diameter of Ø 16.93 mm make this pin particularly suitable for confined test fixturing and short‑reach gauges. The workshop version designation signals enhanced robustness against day‑to‑day mechanical stresses, helping maintain measurement stability in a busy production environment. The modest mass supports quick manual positioning and straightforward integration into existing gaging procedures without introducing unnecessary inertia. Micro class accuracy and traceable identification for quality workflows Classified in the Micro category (measurement range up to 100 mm), this single gauge pin is tailored to precision tasks such as micro‑mechanical checks and small component assemblies where compactness and stiffness provide the best compromise. Identification via SKU and GTIN ensures traceability in quality documentation and stock management, while the Metav IndustryLine origin reflects an industrial focus on reproducible quality across batches. The combination of a clearly defined diameter, robust material and tight tolerance promotes confidence in both inspection results and downstream process decisions. Contact Metav Werkzeuge for technical advice on integrating the Metav IndustryLine gauge pin M323.G93 into existing inspection routines and to request availability details from our Emmerich quality hub. Technical Data Article number: M323.G93 GTIN: 4061905070549 eClass: 21170231 Weight: 0.15 kg Material: Special steel Length: 50 mm Diameter: 16.93 mm Accuracy: ±0.002 mm Facts Length: 50 mm Diameter: 16.93 mm Weight: 0.15 kg Accuracy: ±0.002 mm GTIN: 4061905070549 Special features Workshop version Single gauge pin for end‑measurements Category: Gauge pins (Messstifte) Suitable for fit checks and bore verification SKU: M323.G93 FAQ What tolerance can be expected with this gauge pin? The gauge pin M323.G93 is specified with an accuracy of ±0.002 mm, suitable for tight fit checks and precision inspection tasks. Is the pin material suitable for repeated contact measurements? Yes, the pin is made from special steel, chosen for surface resilience and dimensional stability during frequent use in workshop conditions. Which measurement class does this product belong to? This item falls into the Micro class (measurement range up to 100 mm), designed for compact, high‑precision checks on small components. Can the pin be used for checking dowel fits and bores? The single gauge pin is intended for end‑measurements and fit verification of dowels and bores; its diameter 16.93 mm and workshop specification support such applications. How is the product identified for inventory and traceability? Identification is provided via the SKU M323.G93 and GTIN 4061905070549, enabling clear traceability in quality records and stock systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.94mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Benefit from precise ±0.002 mm conformity, special steel durability and a workshop-ready protective case for reliable inspection and assembly checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.G94 – 16.94 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.G94 is a single precision test pin designed for end‑measure and fit verification tasks in workshop and inspection settings. ±0.002 mm tolerance for precise fits Special steel for wear resistance Workshop version, robust finish 50 mm length, 16.94 mm diameter Repeatable precision for inspection and assembly The core advantage of this test pin is its tight tolerance of ±0.002 mm, which ensures reproducible results when checking bores, dowel fits or seating surfaces. Such accuracy aligns this item with fine workshop inspection tasks where small deviations cause assembly issues. The narrow tolerance reduces rework by providing a clear go/no‑go reference and supports faster decision making on the shop floor. As a single checking element, the pin is straightforward to deploy in gauges or fixtures and pairs well with bench measurement processes that prioritise consistent pass/fail criteria. Robust construction for frequent use Manufactured from special steel, the component is produced for longevity under repeated handling and contact with mating parts. The workshop execution indicates a surface finish and hardness tailored to everyday use rather than delicate laboratory handling, so the pin resists wear and preserves its geometry. Delivered in a protective transport case, the piece remains secure during storage and transit, reducing the risk of nicks that would compromise measurement. The compact 50 mm length and 16.94 mm diameter balance stiffness with easy manual handling, making the pin practical for both handheld checks and integration in simple fixtures. Traceable identification and practical data for procurement The test pin is identifiable via SKU M323.G94 and GTIN 4061905070556, which simplifies inventory, replacement and quality records. Key dimensional data — 16.94 mm diameter, 50 mm overall length and a mass of 0.15 kg — provide immediate orientation for fixture design and handling procedures. The combination of clear labelling and stable material means the pin can be relied upon as a reference part for routine inspections and incoming quality control, supporting efficient workflows and predictable production outcomes without complexity. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine gauge pin fits existing inspection setups and to arrange supply directly from Emmerich. Technical data Article number: M323.G94 Label: Prüfstift, einzeln, 16,94 mm Länge 50 mm GTIN: 4061905070556 Material: Special steel Version: Workshop execution Packaging: Protective transport case (plastic or wooden) Facts Diameter: 16.94 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Category: Messstifte (gauge pins) Workshop-ready finish Single test pin for end‑measure and fit verification FAQ What tolerance does the pin provide? The pin offers a tolerance of ±0.002 mm, making the M323.G94 suitable for precise fit and go/no‑go checks in inspection routines. Can this pin be used in production gauges? Yes, the workshop design and consistent geometry of the checking pin make it appropriate for incorporation into simple gauges and assembly fixtures. What material is the pin made from? The pin is manufactured from special steel to provide wear resistance and stable dimensional behaviour during repeated use. How is the item delivered to avoid damage? Delivery is in a protective transport case (plastic or wooden), which minimises handling damage and keeps the pin ready for immediate use. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.95mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of exact ±0.002 mm tolerance, a defined diameter of 16.95 mm and a compact 50 mm length to ensure repeatable end‑size inspection and robust fixture checking; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single 16.95 mm — 50 mm length | Metav IndustryLine The Gauge pin, single 16.95 mm is a precision reference pin for end‑size inspection and fixture alignment in workshop and quality‑control environments. Precision tolerance ±0.002 mm Diameter 16.95 mm for end‑size checks 50 mm overall length, workshop design Made from special steel for durability Consistent measurement results through tight tolerance The core advantage of this reference pin is its ±0.002 mm tolerance, which reduces measurement uncertainty and supports reliable go/no‑go assessments and dimensional comparisons. A narrowly controlled diameter of 16.95 mm provides a reproducible datum for gauge blocks, fixtures and bore checks; this leads to fewer retests and steadier process control. The precision class specified is suitable where small deviations directly impact assembly fit and functional performance. Durable construction for everyday workshop use Manufactured from special steel, the pin combines wear resistance with a stable surface finish that maintains dimensional integrity across repeated use. The workshop version design balances robustness with handling convenience: its 50 mm overall length offers a secure engagement in fixtures while remaining compact enough for frequent manual handling. The material choice and finish keep maintenance straightforward and service intervals predictable. Practical role in inspection, set‑up and production control As a single gauge element, the pin is optimised for end‑size checks and datum verification during setup and serial inspection. Its compact geometry simplifies insertion and extraction in bore and fixture checks, supporting faster changeovers and a more efficient quality workflow. Traceability is aided by the clear identification M323.G95, which helps integrate the item into existing inspection documentation and inventory lists. Contact Metav Werkzeuge today for tailored advice and to place an order for the Metav IndustryLine gauge pin M323.G95 — application support is available from our Emmerich team Technical data Article number: M323.G95 GTIN: 4061905070563 Manufacturer: Metav IndustryLine Facts Diameter: 16.95 mm Overall length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop version Single gauge pin for end‑size inspection Material: special steel Label: Prüfstift, einzeln — end‑size application FAQ What applications is this gauge pin intended for? The gauge pin M323.G95 from Metav IndustryLine is intended for end‑size inspection, fixture alignment and datum verification in workshop and production environments. How precise is the diameter of the pin? The diameter of the pin is controlled to ±0.002 mm, which supports repeatable dimensional checks and reduces inspection variability. What material is used for the pin? The pin is made from special steel, selected for wear resistance and stable dimensional behaviour under regular workshop use. How is the product identified for inventory and documentation? Identification is by article number M323.G95 and GTIN 4061905070563, assisting traceability in inspection records and stock systems. Is the pin suitable for fixture set‑up and frequent handling? Yes — the 50 mm overall length and robust workshop design make the pin suitable for repeated insertion and extraction during fixture set‑up and serial inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.96mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of precise diameter control and a tight tolerance for consistent end‑dimension checks; the robust special steel construction and workshop specification ensure durable everyday use. Order the M323.G96 directly via Metav Werkzeuge or consult our specialists for integration advice. Gauge pin M323.G96 — Single test pin, Ø 16.96 mm, 50 mm length (Metav IndustryLine) A gauge pin for reliable end‑dimension verification and routine workshop inspection applications, designed as a single‑piece test pin with workshop specification. High-precision diameter 16.96 mm Tight tolerance ±0.002 mm Special steel for daily workshop use 50 mm effective measuring length Consistent inspection results through tight dimensional control The M323.G96 is engineered for repeatable measurement in production and inspection environments, combining a nominal Ø 16.96 mm diameter with a certified tolerance of ±0.002 mm. This level of specification supports fast go/no‑go decisions and reduces rework by delivering predictable fits when checking end dimensions. The compact design and defined length make the component especially useful for end‑gauge applications and final inspection stages, where consistent contact geometry and dimensional stability matter for throughput and quality control. Durable construction that suits workshop workflows Manufactured from special steel and supplied in a workshop configuration, the pin is built to withstand frequent handling and the mechanical demands of a shop floor. The material choice balances surface hardness with resistance to wear, preserving the critical diameter over prolonged cycles and reducing replacement frequency. Such durability translates into lower process interruptions and predictable inspection intervals, which supports efficient scheduling and reduces hidden costs associated with unexpected tool wear. Practical dimensions for straightforward integration With a 50 mm length the test pin offers a useful working reach without compromising stiffness, making it straightforward to use in fixtures, plug gauges or bench inspection setups. The single‑piece format and clear identification simplify inventory and traceability in busy inspection environments. The product’s compact footprint also eases handling and storage while ensuring the required contact geometry for reliable measurement outcomes during assembly or final checks. Contact Metav Werkzeuge today to discuss how the M323.G96 gauge pin can be matched to existing inspection fixtures or to request technical clarification from our Emmerich‑based specialists Technical Data SKU: M323.G96 GTIN: 4061905070570 Description: Single gauge pin, Ø 16.96 mm, length 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 16.96 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Application hint: End‑dimension checks / end gauges Story trigger: endmasse FAQ What is the intended use of this gauge pin? The M323.G96 gauge pin is intended for end‑dimension verification and go/no‑go checks in workshop and inspection contexts, providing a stable reference for assembly and final inspection. What accuracy can be expected from this pin? With a specified tolerance of ±0.002 mm, the M323.G96 delivers high precision suitable for tight fit checks and reliable repeatability in routine inspection tasks. Which material is used for the pin and why? The pin is made from special steel to offer a balance of wear resistance and surface stability, ensuring longevity under regular workshop use. Can this pin be used in fixture and plug‑gauge applications? Yes, the 50 mm length and single‑piece format make the M323.G96 suitable for integration into fixtures and plug gauges where defined contact geometry is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.97mm Test Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the precise diameter, tight tolerance and robust workshop design to ensure repeatable end‑size checks and dependable in‑process gauging. Combine accuracy (±0.002 mm), special steel construction and compact length for stable handling — order the gauge pin directly via Metav Werkzeuge or consult our specialists for specification advice. Metav IndustryLine gauge pin, single, Ø 16.97 mm · 50 mm length Metav IndustryLine single inspection pin designed for end‑size checks and fixture gauging in workshop environments. Workshop version for robust use Diameter 16.97 mm precision ground Length 50 mm for stable insertion Tolerance ±0.002 mm for fine inspection Precision that minimises rework and speeds control The gauge pin is engineered for consistent dimensional verification: with a nominal diameter of 16.97 mm and a verified tolerance of ±0.002 mm, it supports fine inspection tasks where repeatability is decisive. Such accuracy reduces measurement scatter during batch checks and shortens the time between measurement and corrective action, delivering clear cost‑efficiency benefits in production control. The concise geometry translates directly into reliable contact points in fixtures and gauges, which means fewer rejected parts and smoother quality workflows. Robust construction for everyday workshop demands Made from special steel, this single inspection pin resists wear from repeated seating and withdrawal in jigs and assembly fixtures. The 50 mm length gives sufficient engagement for secure placement without excess overhang, while the modest mass (approx. 0.15 kg) makes handling straightforward during rapid inspection cycles. These attributes combine to offer durability in routine use and predictable measurement behaviour, so inspection routines remain fast and low in operator effort. Practical integration into inspection routines and fixtures Designed for end‑size and go/no‑go validation in assembly and metrology stations, the pin is suited to handheld checks, fixture inserts and go‑gauge arrangements. The compact format supports dense fixturing layouts and simplifies storage in metrology cabinets. Traceability is supported via the product SKU and GTIN for inventory and process documentation. Backed by Metav’s distribution and quality processes, the pin is a pragmatic choice where dependable, repeatable gauging is required for production or incoming inspection. Choose the Metav IndustryLine gauge pin for reliable end‑dimension checks — contact Metav Werkzeuge for order and technical clarification to match the pin to your inspection tasks Technical Data Article number: M323.G97 GTIN: 4061905070587 Brand: Metav IndustryLine Weight: 0.15 kg Material: Special steel Core data Diameter: 16.97 mm Length: 50 mm Tolerance: ±0.002 mm Label: Inspection pin, single, 16.97 mm, length 50 mm Special features Workshop execution Single inspection pin for end‑size checks Suitable for fixture and jig gauging FAQ What is the nominal diameter and tolerance of this pin? The inspection pin has a nominal diameter of 16.97 mm with a tolerance of ±0.002 mm, making it suitable for fine dimensional verification. Is the pin suitable for fixture gauging and go/no‑go checks? Yes, the Metav IndustryLine single inspection pin (SKU M323.G97) is designed for fixture inserts and end‑size checks in workshop and production environments. What material is the pin made from and why does it matter? The pin is manufactured from special steel, chosen for wear resistance and dimensional stability during repeated seating and removal. How does the length affect use in fixtures? The 50 mm length provides secure engagement with fixture bores while keeping overhang minimal, aiding stable measurements and reduced flex. Can this pin be used for high‑volume repeat inspections? The combination of special steel construction and tight tolerance supports frequent use in production checks, with predictable measurement behaviour across cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.98mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-grade construction, ±0.002 mm dimensional accuracy and a compact 50 mm length for reliable end‑dimension checks; order the test pin directly via Metav Werkzeuge or consult the Metav team for application advice. Test pin M323.G98 — single control pin, Ø 16.98 mm, 50 mm length, Metav IndustryLine The Test pin M323.G98 is a workshop-grade control pin for precise end‑dimension verification and fixture reference in production and inspection environments Workshop-grade design Nominal diameter Ø 16.98 mm 50 mm overall length Dimensional tolerance ±0.002 mm Delivered in protective case Precision where tolerances count The M323.G98 control pin delivers high reproducibility through a tight dimensional specification of ±0.002 mm, making it suitable for fine inspection tasks and go/no‑go checks in shopfloor environments. With a nominal diameter of 16.98 mm, the pin provides a defined reference surface for comparative measurements and repeatable alignment in jigs and fixtures. The specified tolerance is a technical guarantee that supports quality control regimes and helps reduce scrap rates by ensuring that critical fits are evaluated against a stable reference. Robust workshop construction for daily use Manufactured in special steel, this workshop version is designed for handling and routine use rather than delicate laboratory duty; the material choice balances wear resistance and dimensional stability. The compact 50 mm overall length and modest mass (approx. 0.15 kg) ease handling and positioning in confined setups, while the supply in a protective case minimises transport damage and protects measuring faces between uses. These attributes contribute to longer service life and fewer unplanned replacements, increasing uptime on the production line. Practical benefits in inspection and assembly As a single control pin for end‑dimension and reference measurements, the component integrates into assembly verification steps, fixture set‑up and finish inspection. The clear nominal size of 16.98 mm simplifies documentation and traceability when recording results, and the pin’s compact form factor supports rapid swap‑out during batch changeovers. Where reproducible contact points are required, this workshop pin acts as a dependable mechanical datum, helping technicians maintain consistent assembly tolerances with straightforward handling. Choose the Metav IndustryLine M323.G98 when repeatable, workshop‑proven reference gauges are required — contact Metav Werkzeuge for tailored ordering and application guidance via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: M323.G98 GTIN: 4061905071355 Manufacturer: Metav IndustryLine Facts Nominal diameter: 16.98 mm Overall length: 50 mm Dimensional tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop execution Delivered in protective case Category: test pin FAQ What level of accuracy does the test pin provide? The test pin M323.G98 is specified with a dimensional tolerance of ±0.002 mm, suitable for precise shopfloor checks and comparative inspections where tight repeatability is required. What material is used for the control pin? The pin is made from special steel, chosen for mechanical robustness and dimensional stability in workshop conditions. Is the test pin supplied with protective packaging? Yes, the M323.G98 is supplied in a protective case to reduce handling damage during transport and storage. For which tasks is this control pin most suitable? This single test pin is designed for end‑dimension verification, fixture referencing and go/no‑go checks in production and inspection workflows. How should the pin be referenced in documentation and traceability records? Record the nominal diameter 16.98 mm, the article number M323.G98 and the stated tolerance ±0.002 mm to ensure clear traceability in quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.99mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the precise diameter control, robust workshop construction and transport-ready packaging to improve repeatability in end‑measure inspection. Order the gauge pin directly via Metav Werkzeuge or consult the technical advisors for application support. Gauge pin M323.G99 — precision measuring pin, Ø 16.99 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.G99 is a workshop-grade measuring pin designed for end‑measure verification and precision fit checks in production and quality control. High repeatability with ±0.002 mm tolerance Exact diameter of 16.99 mm for end‑measure checks Compact 50 mm length for restricted spaces Workshop version with transport case for safe handling Repeatable measurements where tolerance matters The M323.G99 gauge pin delivers high repeatability thanks to its narrow tolerance of ±0.002 mm, making it suitable for fine inspection tasks and assembly control where small deviations have direct consequences. A defined diameter of 16.99 mm provides a clear reference for go/no‑go checks and dimensional verification. The tight manufacturing tolerance reduces uncertainty in statistical process control and supports consistent quality documentation. Robust construction adapted to shop floor conditions Manufactured from special steel, this measuring pin is built to withstand regular workshop use while retaining measuring integrity. The workshop version specification means surfaces and finishes are chosen to resist wear during repeated insertion and handling. With a practical 50 mm active length and a mass of 0.15 kg, the pin balances stiffness and manoeuvrability so that measurements remain stable even in confined fixturing. Delivery in a transport case protects the component during storage and shipping, preventing accidental damage and preserving calibration status. Practical use and integration into inspection routines This single gauge pin is suited to end‑measure controls, fit checks and comparative gauging in production environments. It is supplied as an individual precision pin for use with gauge blocks, fixture bores or verification templates; traceability is supported by the included article identifiers. The compact format eases handling in assembly stations and inspection benches, while the material choice minimises the need for frequent replacement. For organisations seeking dependable small‑part inspection, the component supports lean metrology workflows and fast decision making on the shop floor. For supply and expert advice on integrating the M323.G99 into existing inspection procedures, contact Metav Werkzeuge — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: M323.G99 GTIN: 4061905071362 Manufacturer: Metav IndustryLine Numbers / Core technical data Diameter: 16.99 mm Length: 50 mm Weight: 0.15 kg Tolerance / Accuracy: ±0.002 mm Special features / Versions Workshop version Material: special steel Supplied in transport case Category: gauge pins FAQ What inspection tasks is this gauge pin best suited for? The M323.G99 gauge pin is designed for end‑measure verification, fit checks and go/no‑go assessments in production and quality control procedures. Is the material suitable for repeated shop floor use? Yes, the pin is made from special steel and the workshop version is specified to tolerate regular handling and insertion without rapid degradation. How precise is the diameter on the M323.G99? The diameter is manufactured to 16.99 mm with a tolerance of ±0.002 mm, supporting tight inspection criteria. Does the product come with protective packaging for transport? Delivery of the M323.G99 includes a transport case to protect the pin during storage and shipping. Can this single gauge pin be used with gauge blocks or fixtures? Yes, the M323.G99 is suitable for use with gauge blocks, fixture bores and templates for comparative gauging and assembly checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.9mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Benefit from a workshop‑grade construction combined with a 16.90 mm nominal diameter and ±0.002 mm tolerance to ensure repeatable bore checks and fewer reworks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.G90 — 16.90 mm × 50 mm (Workshop version, Metav IndustryLine) The Gauge pin M323.G90 is a single workshop‑grade plug gauge designed for precise bore verification and end‑measure checks in routine inspection and setup tasks. Workshop‑grade construction Nominal diameter 16.90 mm Length 50 mm for depth checks Tolerance ±0.002 mm high precision Precise bore verification that reduces rework A compact verification tool, this gauge pin provides a clear, measurable reference for bore acceptance with a declared tolerance of ±0.002 mm, equivalent to 2 µm. Such repeatability supports tighter assembly tolerances and reduces costly rework by confirming fit and concentricity quickly. The nominal 16.90 mm diameter is given as the measurement target; using dedicated pins for go/no‑go or limit testing shortens setup time and increases throughput in inspection loops. Robust workshop design for everyday use Constructed from special steel in a workshop execution, the pin is dimensioned at 50 mm length to allow simple depth and end‑measure checks while remaining easy to handle. The solid build offers dependable contact stability during insertion, which improves the quality of comparative checks against master gauges. Lightweight handling characteristics and compact geometry suit bench inspection and machine setup tasks where rapid, repeatable checks are required. Practical integration into quality control routines Incorporating the M323.G90 into regular quality control procedures streamlines documentation of end‑measure results and helps maintain traceable inspection practices. The single‑piece design is ideal for spot checks, assembly verification and calibration routines where a stable reference diameter is needed. Combined with Metav IndustryLine’s catalogue of metrology tools, this pin supports a pragmatic approach to reliable measurement and consistent production quality. For workshop‑grade bore gauging and tailored guidance on the M323.G90, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 for ordering and technical clarification Technical data Article number: M323.G90 GTIN: 4061905070518 Category: Gauge pin (single) Dimensions & accuracy Nominal diameter: 16.90 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.15 kg Materials & features Material: Special steel Version: Workshop execution Application: End‑measure and bore verification Packaging: single item, robust format (workshop use) FAQ What is the permitted tolerance for this gauge pin? The tolerance for the Gauge pin M323.G90 is ±0.002 mm, providing a high level of dimensional consistency for routine bore checks. Can the pin be used for depth and end‑measure checks? Yes, the 50 mm length of the M323.G90 allows for simple depth and end‑measure verification in addition to diameter checking. What material is the pin made from and why does it matter? The pin is made from special steel, chosen for dimensional stability and durability in workshop conditions when performing repeated insertions and inspections. Is this item suitable for production floor use? The workshop execution and compact dimensions make the M323.G90 suitable for production floor spot checks, machine setup and incoming inspection tasks. How is the product identified for ordering? Order using the article number M323.G90 (GTIN 4061905070518) from Metav IndustryLine for consistent identification and supply. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16–17mm Gauge Pin Set 101pcs 0.01mm Step With Pin Holder In Plastic Case - Metav IndustryLine
Take advantage of the combination of 0.01 mm graduations, robust special steel construction and a complete 16.0–17.0 mm range for dependable inspection cycles. Order the gauge pin set directly via Metav Werkzeuge or consult our specialists for application-specific advice. M318.586 Gauge Pin Set — 16.0–17.0 mm, 0.01 mm increments (Metav IndustryLine) The M318.586 gauge pin set is a precision inspection kit designed for accurate bore and hole verification in the 16.0–17.0 mm range. 101 precision gauge pins 16.00–17.00 mm 0.01 mm step for fine adjustment Hardened special steel construction Includes removable pin holder Accurate clearance and fit verification for serial inspection The set delivers a continuous range from 16.0 to 17.0 mm with 0.01 mm steps, enabling fine-grained assessment of hole diameters and fit tolerances. The close graduations support repeatable pass/fail decisions during incoming inspection and production sampling; combined with the documented accuracy ±0.004 mm, this range reduces uncertainty when comparing measured clearances to drawing tolerances. By using discrete gauge pins rather than progressive taper gauges, measurement resolution is improved and the inspection workflow becomes more deterministic. Durable design for workshop environments Manufactured from special steel and heat-treated for surface hardness, the pins resist wear while preserving dimensional stability across repeated use. The set's construction prioritises repeatability, meaning the same pin used across multiple checks will exhibit minimal dimensional drift. The physical robustness suits routine machine‑shop handling and supports longer maintenance intervals. Where traceable inspection is required, the set’s stable material and precise stepping make it suitable for laboratory verification as well as on-bench control tasks. Practical organisation and handling that speeds inspection The kit groups 101 individually graduated pins in an organised layout and includes a removable pin holder, which simplifies selection and temporary clamping during gauging. The consistent 50 mm pin length provides sufficient engagement depth for most through‑holes and blind bores without introducing excessive flex; this balance between length and rigidity improves measurement reliability. Lightweight handling of individual pins and a clear layout reduce time spent searching for the correct dimension, supporting faster throughput during batch checks. Suitable applications and complementary use cases This gauge set covers common workshop needs such as bore verification, mandrel checks and go/no-go confirmation in metalworking, toolmaking and assembly lines. The dimensional span is particularly well matched to components where the micro category of measurement applies — compact, high-precision tasks where short jaws or pins are required. The kit is compatible with optical comparators and micrometres for cross‑verification if traceable documentation of results is needed; it is also convenient for quality inspectors who require fixed, discrete references rather than continuously variable measuring instruments. For precise bore inspection and robust workshop performance, request the M318.586 through Metav Werkzeuge’s Emmerich hub or contact our experts for guidance on integrating the set into existing inspection routines. Technical data SKU: M318.586 GTIN: 4054469156231 ECLASS: 21170231 Tariff code: 90173000 Core specifications Measurement range: 16.0–17.0 mm Step size: 0.01 mm Declared accuracy: 0.004 mm Pin length: 50 mm Pieces per set: 101 Set weight: 11.7 kg Materials & features Material: Special steel Special feature: with pin holder Set type: graduated gauge pins Label: Prüfstift-Satz, 101-tlg. 16 - 17 mm Abstufung 0,01 mm FAQ What is the smallest increment in the set? The kit provides 0.01 mm increments between successive pins for precise stepwise checks. Can the pins be used for blind bore measurements? Yes. With a 50 mm pin length many blind bores can be assessed; longer engagement may require complementary probes. What tolerance can be expected from the gauges? The set is specified with an accuracy of 0.004 mm, supporting reliable pass/fail inspection within close tolerances. Is the material suitable for workshop use? The pins are made of special steel, heat-treated to resist wear and preserve dimensional stability in routine shop environments. How does this set assist serial inspection workflows? Discrete steps and clear organisation speed up selection and reduce interpretation time, enabling efficient batch checking and traceable verification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
17.01mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of high repeatability and workshop-grade robustness for reliable in-process checks; the tight tolerance of ±0.002 mm and the stable 50 mm engagement ensure consistent final-size verification. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge Pin M323.H01 — 17.01 mm diameter, 50 mm length (Metav IndustryLine) The Gauge Pin M323.H01 is a workshop-grade precision plug gauge designed for final-size inspection and go/no-go checks in production and quality control. Workshop-grade construction for daily use Diameter 17.01 mm with ±0.002 mm tolerance Stable 50 mm engagement for repeatable seating Supplied in a protective transport case Precision that protects quality and reduces rework The plug gauge delivers the decisive advantage of consistent pass/fail decisions thanks to its exceptionally tight tolerance of ±0.002 mm. With a diameter of 17.01 mm, this test pin performs final-size verification where small deviations have large consequences; the narrow error band reduces scrap and minimises costly rework. The dimensional stability offered by the design converts a single measurement into a reliable production control point, helping maintain process capability across batches. Durable design built for the workshop environment Manufactured from special steel and specified as a workshop-grade item, the pin withstands repeated use on shop floors without rapid wear. The 50 mm length provides secure engagement in fixtures and jigs, improving alignment and reducing wobble during insertion. Supplied in a protective transport case, the gauge arrives ready for safe storage and handling between uses; this packaging prevents nicks and preserves the calibration state for longer service intervals. Simple integration into existing inspection routines The plug gauge is immediately usable in go/no-go fixtures and manual inspection benches as a straightforward physical standard. Its compact form and clear dimensional definition make it suitable for assembly lines, incoming inspection and rapid final checks. Traceability is supported by the included SKU and GTIN identifiers, allowing easy logging into quality records and inventory systems; the solid construction means repeatability and tactile feedback during checks, which is useful where quick, reliable decisions are required. For purchase enquiries or technical advice regarding the Metav IndustryLine gauge pin M323.H01, contact Metav Werkzeuge to discuss specification fit and availability Technical data Article number: M323.H01 GTIN: 4061905071386 Manufacturer: Metav IndustryLine Facts Diameter: 17.01 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Workshop version Supplied in protective transport case Category: gauge pin (Messstifte) FAQ What tolerance does this gauge pin offer? The Metav IndustryLine gauge pin M323.H01 is specified with an accuracy of ±0.002 mm, suitable for tight final-size checks and high repeatability in workshop environments. Is the pin suitable for use in handheld go/no-go checks? Yes, the 50 mm length and robust construction make the pin suitable for handheld or fixture-mounted go/no-go checks on assembly and inspection benches. What is the material and how does it affect wear? Constructed from special steel, the plug gauge provides improved wear resistance compared with softer materials, extending service life under frequent use. How should the gauge pin be stored between uses? The gauge pin is supplied in a protective transport case; storing it in that case when not in use prevents surface damage and helps maintain measurement integrity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com