Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
9.01-10 mm Gauge Pin Set 100 Pieces 0.01 mm Increment Supplied in Case - Metav IndustryLine
Take advantage of a finely graduated set that combines reliable diameter verification with workshop-grade robustness; the precise 0.01 mm steps and a typical tolerance of ±0.002 mm support repeatable decisions on the shop floor. Order the kit directly via Metav Werkzeuge or ask Metav's consultants for specification advice and availability. Gauge pin set M318.559 — 100-piece, 9.01–10.00 mm (0.01 mm steps) by Metav IndustryLine The Gauge pin set M318.559 is designed for precise diameter checking and fit verification across the 9.01–10.00 mm band, suitable for inspection, tool setting and acceptance testing in production environments 0.01 mm step for fine incremental gauging High-grade special steel construction Measurement range 9.01–10.00 mm Supplied in protective case for transport Consistent precision for inspection and quality control The gauge pins in this kit span the 9.01–10.00 mm range in 0.01 mm increments, enabling fine gradation when verifying bore sizes or checking shaft diameters. With a measured tolerance on the order of ±0.002 mm, the set supports reproducible go/no-go and transition-fit checks that reduce subjective judgement in routine inspection. Made from special steel, the pins resist wear under repeated contact and retain dimensional stability, which is crucial when used as a reference during first-article inspection or in-process checks. Built for workshop use and safe transport Organised storage and safe handling reduce downtime: the kit is delivered in a secure, organised box and has a collective weight of 4.5 kg, which keeps the set portable while protecting individual gauges. Each pin has a length of 50 mm, optimised for stable support in seating and insertion tasks without excessive overhang. The 100-piece composition provides dense resolution across the interval so that technicians can reach the exact diameter step quickly without resorting to filing or shimming, improving throughput at the measuring bench. Speeding up inspection and reducing downtime Using a finely stepped set like this accelerates decision-making in production inspections: installers and inspectors find the matching pin rapidly, avoiding iterative caliper measurements and reducing cycle time. The kit is particularly useful for assembly checking, fixture set-up and routine acceptance testing where fast, objective diameter verification prevents rework. Backed by Metav IndustryLine's distribution and quality control, the set supports reliable supply and consistent lot quality for small-batch and continuous operations alike. For tailored specification support or to secure supply from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for availability and delivery guidance — Metav Werkzeuge can advise on application fit and dispatch the required items directly Technical data Article number: M318.559 GTIN: 4054469129426 HS code: 90173000 Manufacturer: Metav IndustryLine Dimensions & precision Measurement range: 9.01–10.00 mm Graduation: 0.01 mm Accuracy: ±0.002 mm Pieces per set: 100 Individual pin length: 50 mm Weight (total): 4.5 kg Materials & features Material: Special steel Protective transport case included Category: Gauge pins / inspection gauges Intended use: Diameter verification, fit checks, fixture set-up FAQ What is the intended use of this gauge pin set? The gauge pin set M318.559 is intended for diameter verification, go/no-go checks and fixture setting where incremental diameter selection between 9.01 mm and 10.00 mm is required. How fine are the increments and what tolerance can be expected? Increments are 0.01 mm and the typical tolerance associated with this kit is ±0.002 mm, giving fine-grain control for close-tolerance inspections. Which materials are the pins suitable for measuring? The pins are made from special steel and are used to measure diameters of shafts and bores made from common workshop materials; they are a measuring standard rather than a cutting tool. Is the kit suitable for workshop environments with frequent handling? Yes. The set is supplied in a protective case and the pins are designed for repeated insertion and extraction; organised storage reduces handling time and wear. Can this set replace micrometre checks for small production batches? For quick verification and fit decisions the set provides faster throughput; where traceable absolute measurements are required, complementing pins with calibrated micrometres is recommended. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.01-10.0 mm Precision Gauge Pin Set With Pin Holder 0.01 mm Graduation In Plastic Case - Metav IndustryLine
This gauge-pin set delivers traceable, workshop-ready sizing across the 9.01–10.00 mm range while combining fine 0.01 mm increments with a declared accuracy of 0.004 mm, enabling consistent pass/fail checks and high-repeatability gauging; order directly via Metav Werkzeuge or speak to our consultants for specification support. Gauge Pin Set M318.579 — 101-piece, 9.01–10.00 mm, 0.01 mm graduations (Metav IndustryLine) A Metav IndustryLine gauge pin set designed for precision diameter verification and toolsetting in inspection, toolroom and production environments. 101-piece hardened gauge pin set Diameter range 9.01–10.00 mm per 0.01 mm step Graduation 0.01 mm for fine adjustment Holder included for organised handling Consistent dimensional control through measurable precision The set is engineered to support reliable size verification and incremental adjustment tasks with a declared accuracy of 0.004 mm, which keeps tolerance checks tight and reduces rework. Using pins in 0.01 mm steps permits fine interpolation between standard nominal sizes, so set-up and verification processes become more predictable. For users in quality assurance and production metrology, this translates into fewer rejected parts and steadier process capability. Practical set composition that speeds inspection and set-up Supplied as a comprehensive kit, the tools cover diameters from 9.01–10.00 mm in 0.01 mm increments and each pin has a usable length of 50 mm, making them suitable for a wide range of holes and bores. The pins are manufactured from special steel, offering a balance of surface hardness and corrosion resistance that supports repeated use. The inclusion of a dedicated holder assists orderly storage and quick selection during serial inspection or machine set-up, improving throughput and operator ergonomics. Designed for integration into workshop workflows The modular nature of this set supports both bench inspection and on‑machine referencing: the compact, graduated increments aid precise alignment of fixtures and cutting tools, while the robust construction stands up to everyday handling. Backed by Metav’s long-standing supply chain and quality assurance ethos, the kit is aimed at shops and maintenance departments seeking dependable measuring aids that simplify process control and minimise downtime. Contact Metav Werkzeuge for detailed technical guidance on Metav IndustryLine gauge pin sets and to discuss how this precision kit can be integrated into existing inspection routines; eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M318.579 GTIN: 4054469168333 Manufacturer: Metav IndustryLine Facts Diameter range: 9.01–10.00 mm Graduation: 0.01 mm Nominal accuracy: 0.004 mm Length (usable): 50 mm Weight (set): 4.17 kg Special features Material: Special steel Set: 101 pieces Inclusive: Pin holder FAQ What diameter range does the set cover? The set covers diameters from 9.01 mm to 10.00 mm in 0.01 mm increments, allowing detailed sizing within that band. Is the accuracy suitable for workshop quality control? Yes, the set is specified with a nominal accuracy of 0.004 mm, which supports tight tolerance checks in routine inspection tasks. What material are the pins made from? The pins are manufactured from special steel designed for repeated use and good dimensional stability. How is the set organised for use during inspection? The kit includes a dedicated pin holder to keep pins organised and to speed selection during measurement and setting operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.01mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Finish - Metav IndustryLine
Precision end-dimension control combined with workshop-grade durability: the gauge pin delivers Ø 9.01 mm nominal size with ±0.001 mm accuracy over a 50 mm length, enabling consistent final-dimension checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed Gauge pin M323.901 — 9.01 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The gauge pin M323.901 is a precision measurement pin designed for final-dimension inspection in industrial metrology and workshop environments, offering a compact reference for verification of bore and end measurements High-precision Ø 9.01 mm ±0.001 mm Special steel for workshop use 50 mm length for repeatable contact Securing final dimensions with micrometre-level accuracy The core advantage lies in the exceptionally tight tolerance of ±0.001 mm (1 µm), which positions this pin as a practical reference for critical end-dimension tasks. Such precision reduces measurement ambiguity during acceptance checks and process control, providing a reliable physical standard for comparative inspections. The nominal Ø 9.01 mm is suitable where small-diameter bores and end fits must be verified with minimal uncertainty, and the specified tolerance supports traceable quality routines that prioritise reproducibility over multiple cycles. Durable workshop execution for everyday metrology Built as a workshop version, the pin combines precise geometry with materials chosen for routine use: special steel provides dimensional stability and wear resistance under repeated engagement. The 50 mm length ensures a consistent contact area for tactile probing and comparative gauging on bench-mounted equipment. Delivered as a single item, this compact measurement accessory is easy to store and to integrate into existing inspection kits, making it a pragmatic choice for production floors where robustness and repeatability matter. Fit into quality-control workflows and documentation Integration into established inspection processes is straightforward: the pin functions as a reference for end-dimension checks and complements micrometre and bore-gauge measurements. Its small footprint supports quick comparative checks during first-article inspections or spot checks in series production. For procurement and inventory, the clear identification and industrial-grade specification help maintain measurement chains and reduce the risk of ambiguous results in acceptance protocols; the technical values permit straightforward inclusion in quality documentation and equipment lists. For reliable end-dimension verification using Metav IndustryLine quality, contact Metav Werkzeuge to discuss availability or to request a specification review by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: M323.901 GTIN: 4061905062056 Product: Gauge pin, single, 9.01 mm, ±0.001 mm, length 50 mm Facts Diameter: 9.01 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.029 kg Material: Special steel Features and applications Workshop version Category: Messstifte (gauge pins) Intended use: Final-dimension inspection / end measurements Delivery form: Single item FAQ What is the intended use of this gauge pin? The gauge pin is intended for final-dimension inspection and verification of small bores or end fits, using the Ø 9.01 mm nominal size and the ±0.001 mm tolerance as a comparative reference. Which material is the pin made from and why does it matter? The pin is manufactured from special steel, chosen for dimensional stability and wear resistance in workshop conditions, helping to maintain consistent contact geometry over repeated checks. How precise is the measurement reference provided by this pin? With a stated tolerance of ±0.001 mm (1 µm), the pin offers micrometre-level reference precision suitable for high-accuracy acceptance checks and process control tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.02mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm repeatability together with a compact 50 mm length and robust construction for reliable dimensional checks in the workshop; supplied as a single gauge pin in a protective transport case for safe handling. Order the gauge pin directly via Metav Werkzeuge or consult Metav's specialists for further specification advice. Gauge pin M323.902 — 9.02 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Gauge pin M323.902 is a single precision gauge pin intended for end‑dimension inspection and fixture checks in industrial and workshop environments, offering a tight tolerance and compact form for routine quality control tasks. Precision tolerance ±0.001 mm Diameter 9.02 mm for end‑measure fits Solid special steel construction Supplied in transport case Precision where it matters High‑accuracy measurement is the principal benefit of this design: the ±0.001 mm tolerance delivers a fine measurement window that supports strict acceptance criteria and reduces the risk of part rejection in serial production. With a nominal diameter of 9.02 mm and a 50 mm length, the pin provides a stable reference for end‑measure gauges and plug‑gauge checks. The compact geometry limits lever effects and runout, which preserves repeatability during quick inspection cycles and makes the pin suitable as a master for comparative checks on production batches. Durable construction for routine workshop use Constructed from special steel, this workshop version emphasises wear resistance and dimensional stability under frequent handling. The hardened surface and precise grinding process ensure low surface roughness and consistent fit in mating bores, supporting frequent insertion and withdrawal without rapid degradation. The modest mass aids handling while maintaining rigidity; the combination of material and finish extends service life and reduces downtime for replacements, contributing to a predictable inspection workflow in busy shops. Practical handling and integration into inspection workflows Delivered as a single item with individual packaging for safe transport, the gauge pin is straightforward to store and deploy at the inspection bench. The compact size and clear nominal marking simplify inventory management and help technicians select the correct reference quickly. In bench testing or fixture set‑up, the pin functions as a go/no‑go reference or a transfer standard for setting gauges and checking bore diameters, allowing faster throughput and consistent acceptance decisions across repeated cycles. Efficiency and traceability for production environments Using a dedicated pin with a defined tolerance window reduces measurement uncertainty and supports consistent quality reports. The uncomplicated geometry requires minimal training to integrate into existing inspection plans, while the robustness of the workshop version lowers the frequency of replacements. For operations seeking predictable measurement performance with minimal setup time, this single gauge pin offers a cost‑effective, high‑precision reference that aligns with standard quality routines. Choose Metav IndustryLine’s precision gauge pin M323.902 for dependable inspection results and contact Metav Werkzeuge for tailored procurement or specification support at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.902 GTIN: 4061905062650 Label: Gauge pin, single, 9.02 mm, ±0.001 mm, length 50 mm Facts Diameter: 9.02 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.029 kg Special features Material: special steel Workshop version Supplied in transport case Single item supply FAQ What tolerance does the gauge pin have? The gauge pin has a manufacturing tolerance of ±0.001 mm, specified for the Gauge pin M323.902 from Metav IndustryLine. What are the exact diameter and length? Diameter is 9.02 mm and length is 50 mm for the single gauge pin M323.902. Which material is used for the pin? The pin is made from special steel, selected for wear resistance and dimensional stability in workshop use. How is the item supplied and protected for transport? The item is supplied as a single piece and packaged in a transport case to protect the finished surface during handling and shipment. What applications suit this gauge pin? Designed for end‑dimension inspection, fixture set‑up, plug‑gauge reference and routine quality checks in workshops and production lines Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.03mm Gauge Pin, Single, ±0.001 mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high‑precision tolerancing and a compact workshop design for reliable end‑dimension checks; the pin’s ±0.001 mm tolerance and 9.03 mm diameter ensure repeatable results in production control. Order the item directly via Metav Werkzeuge or contact our consultants for technical advice. Precision gauge pin M323.903 — 9.03 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) A precision gauge pin M323.903 designed for end‑dimension verification, fixture alignment and routine workshop inspection of small bores and mating parts Workshop version, robust construction Diameter 9.03 mm with ±0.001 mm tolerance 50 mm datum length for repeatable checks Made from special steel for wear resistance Reliable tolerancing for end‑dimension control The pin offers an ultra‑fine tolerance of ±0.001 mm, making it suitable for precise end‑dimension verification and go/no‑go fixture applications where small deviations matter. Its nominal diameter of 9.03 mm and defined datum length provide a stable reference for repeatable measurements, reducing uncertainty during batch inspections. The compact mass (approximately 0.029 kg) minimises handling effects and helps preserve measurement consistency across repeated cycles. Built for daily workshop use with durable materials Manufactured in a workshop configuration, the component combines practical robustness with metrological stability. The core material is special steel, selected for wear resistance and dimensional stability under typical shopfloor conditions. The 50 mm length establishes a clear datum for both through‑bore checks and alignment tasks in fixtures, while the single‑piece design simplifies handling and storage. These characteristics translate into longer service life and fewer replacement intervals in regular production use. Integration into inspection routines and traceability The pin is supplied as a single unit (SKU M323.903, GTIN 4061905062667) and is optimised for incorporation into pneumatic or manual checking stations, plug gauges and bench test procedures. Traceable identification facilitates inventory control and documentation in quality management systems. The compact geometry eases integration into assembly jigs where accurate end‑dimension references are required, ensuring faster setup times and consistent pass/fail decisions during quality control runs. For a dependable end‑measurement reference, request the M323.903 from Metav Werkzeuge — contact our Emmerich team at info@metav-werkzeuge.com or +49 2822 7131930 for product availability and application guidance Technical data Article number: M323.903 GTIN: 4061905062667 ECLASS: 21170231 Facts Diameter: 9.03 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.029 kg Special features Workshop version Material: special steel Supplied as single gauge pin Intended for end‑dimension checks and fixture alignment FAQ What tolerance does the pin provide? The pin is manufactured to a tolerance of ±0.001 mm, offering high repeatability for fine dimensional checks with the Precision gauge pin M323.903. Which applications are suitable for this gauge pin? Typical uses include end‑dimension verification, go/no‑go fixtures, alignment of mating parts and quick checks on production lines; the design is aimed at routine workshop inspection. What material is used for the pin? The component is made from special steel, chosen for abrasion resistance and dimensional stability under normal workshop conditions. Is the item supplied as a set or an individual part? The product is supplied individually; the single‑piece format simplifies replacement and inventory management—see SKU M323.903 for ordering. How does this pin support traceability in quality processes? The GTIN and article number allow clear labelling and record keeping, enabling straightforward documentation in inspection protocols and inventory lists. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.04mm Gauge Pin Single ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of a compact inspection solution that combines 9.04 mm nominal size, ±0.001 mm tolerance and a robust 50 mm length for dependable in‑process checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.904 — 9.04 mm, ±0.001 mm, workshop execution (Metav IndustryLine) The gauge pin M323.904 is a single inspection pin designed for high‑precision dimensional checks and fixture set‑up in workshop environments. Single gauge pin 9.04 mm, ±0.001 mm tolerance Length 50 mm for standardised checks Made from special steel for lasting precision Workshop version for robust everyday use Confidence through measurable precision A nominal diameter of 9.04 mm combined with a tight ±0.001 mm tolerance delivers repeatable reference points for go/no‑go arrangements and finish inspections. This level of accuracy corresponds to a micron class gauge, reducing uncertainty in critical fit and assembly tasks and supporting reliable pass/fail decisions on the shop floor. The compact form simplifies handling while ensuring the dimensional datum remains stable during repeated use. Built for everyday workshop handling With a length of 50 mm and construction from special steel, the inspection pin balances stiffness and manageability: long enough to reach common bores and seats, yet short enough to avoid excessive deflection. The modest mass supports quick manual positioning and minimises wear on mating faces. The workshop execution prioritises resilience in routine use, making the component suitable for fixture set‑up, end‑measure checks and comparative gauging without complex fixturing. Simple integration into quality processes The item is supplied as a single inspection pin intended for direct use in dimensional control workflows and for verifying end masses or bore sizes. Its fixed diameter and tolerance simplify documentation in inspection plans and allow straightforward traceability of measurement results. For organisations standardising test routines, the pin can act as a reliable reference gauge in assembly checks, plug gauging or as a master for calibrating simpler handheld devices. For supply and application support of Metav IndustryLine gauge pins — especially the high‑precision 9.04 mm, ±0.001 mm inspection pins — contact Metav Werkzeuge in Emmerich for tailored advice and rapid delivery. Technical data Article number: M323.904 GTIN: 4061905062674 Manufacturer: Metav IndustryLine Facts Diameter: 9.04 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.029 kg Special features Single item delivery Material: special steel Workshop execution FAQ What tolerance does the gauge pin provide? The inspection pin is specified with a ±0.001 mm tolerance, suitable for micron‑level reference and high‑precision pass/fail checks. Which dimensions are relevant for typical checks? Key dimensions are a 9.04 mm diameter and a 50 mm length; the item weighs 0.029 kg and is intended as a compact reference for common bores and seats. Is the product delivered as a set or single item? The product is supplied as a single gauge pin, referenced under article number M323.904. What material is used and how does that affect durability? Constructed from special steel, the pin offers wear resistance appropriate for routine workshop inspections and repeated engagement with mating parts. How is the pin typically used in inspection procedures? It is used as a fixed‑diameter reference for plug gauging, fixture set‑up and comparative dimensional checks to verify end masses and bore conformity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.05mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial‑grade robustness, sub‑micrometre accuracy and compact handling for reliable end‑measure checks in serial inspection or setup work. The precise 9.05 mm diameter and tight ±0.001 mm tolerance ensure reproducible reference points and reduce rework in production. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge Pin M323.905 — 9.05 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge Pin M323.905 is a workshop‑grade precision reference pin designed for end‑measure and setting tasks in inspection and assembly applications. Tolerance ±0.001 mm Diameter 9.05 mm Length 50 mm Special steel construction Precision where repeatability counts A cylindrical reference element with a diameter of 9.05 mm and a certified tolerance of ±0.001 mm provides a stable datum for end‑measurements and go/no‑go comparisons. Such a fine tolerance corresponds to the sub‑micrometre range that prevents cumulative errors when multiple settings are taken across a production batch. The narrow tolerance improves process capability and shortens inspection times, delivering a measurable increase in throughput and fewer rejected parts—an efficiency argument that matters in series production and tooling set‑up. Built for workshop use and everyday handling Made from special steel and specified as a workshop‑grade item, this gauge pin balances wear resistance with handling convenience. At 50 mm length and a mass of approximately 0.029 kg, the pin is compact enough for handheld positioning yet long enough to serve as a stable reference in fixtures and jigs. Supplied individually, the component is suited to spot checks, fixture setting and direct use within small‑batch quality control routines, where robustness and repeatable contact geometry are decisive. Practical integration into inspection routines The dimensional stability and modest footprint of this reference pin simplify its incorporation into comparator benches, depth gauges and fixture set‑ups. As a standardised reference component, it aids traceable measurement workflows and reduces calibration intervals for downstream tooling; regular use as a reference reduces setup variability and supports consistent quality output. The M323.905 is an economical, high‑precision aid to inspection that helps maintain a steady flow in production and raises confidence across measuring tasks. For straightforward procurement and technical advice on integrating this Metav IndustryLine gauge pin into existing inspection processes, contact Metav Werkzeuge — Metav’s consultants will advise on suitability and ordering. Technical Data SKU: M323.905 GTIN: 4061905062681 Brand: Metav IndustryLine Core specifications Diameter: 9.05 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.029 kg Special features Material: Special steel Delivery: single item Designation: workshop execution FAQ What applications is this gauge pin suitable for? The gauge pin M323.905 is intended for end‑measure references, fixture setting and spot inspection in workshop and light production environments where a 9.05 mm reference and ±0.001 mm tolerance are required. Is the material specified for corrosion resistance or coating? The M323.905 is produced from special steel; details on any additional coating are not specified for this item and should be requested if corrosion resistance is a priority. Can the pin be used as a datum in fixture assemblies? Yes, the dimensional stability and compact 50 mm length make the pin suitable as a datum or reference element within fixtures and jigs for repeatable positioning. What level of measurement uncertainty can be expected when using this pin as a reference? Using the gauge pin M323.905 as a hard datum reduces the variability of positioning; the component itself carries a ±0.001 mm manufacturing tolerance, which defines its contribution to overall measurement uncertainty. Is the item supplied individually or as part of a set? The product is supplied as a single gauge pin (individual delivery), intended for direct use or selective stocking in inspection inventories. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.06mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
A compact workshop-grade test pin that combines a tight tolerance of ±0.001 mm, a 50 mm ground length and a special-steel construction to deliver stable, repeatable reference measurements; order directly via Metav Werkzeuge or consult our technical advisers for application matching. Gauge pin, single – 9.06 mm ±0.001 mm | 50 mm length (Metav IndustryLine) The gauge pin, single – 9.06 mm is a workshop-grade measuring pin for precise tolerance checks and reference gauging in quality control and fixture inspection. High-precision ±0.001 mm tolerance Made from special steel 50 mm ground length for stability Workshop version for robust use Consistent precision for routine inspection This measuring pin is manufactured to a tolerance of ±0.001 mm, providing a reliable go/no-go reference for fine inspection tasks. The combination of minimal dimensional deviation and a ground 50 mm length reduces runout and improves seating stability in fixtures, which in turn lowers scrap rates and shortens inspection cycles. Where repeatability matters, a defined tolerance band like this enables confident pass/fail decisions without hourly recalibration. Built for robust workshop conditions Constructed from special steel, the component resists wear while retaining its calibrated profile during repeated contact checks. The workshop execution reflects practical demands: the geometry is optimised for consistent seating in gauges and jigs, and the surface finish supports frictional stability. These characteristics make the pin suited to inline quality checks and intermittent lab use, bridging the gap between delicate laboratory gauges and heavy production tools. Practical benefits for traceable metrology As a single reference pin, the item performs best as part of a measured inspection routine or when used to verify bore diameters and assembly fits. The clearly defined diameter of 9.06 mm and the precise length minimise uncertainty when used as an end-measurement standard. For traceability, each component can be logged against batch and SKU data to support QA documentation and trend analysis of wear over time. Easy integration into existing processes The pin is supplied as a standalone test element that integrates into standard fixture plates and comparator setups, allowing minimal adaptation of current workflows. Specification-driven design eases procurement decisions: selecting a reference pin with verified dimensional stability simplifies process validation. For applications requiring matched sets or dedicated gauge blocks, this single unit is a dependable building block within a broader inspection strategy. For workshop-ready precision from the Metav IndustryLine (M323.906), contact Metav Werkzeuge in Emmerich for application advice and procurement assistance Technical Data Article number: M323.906 GTIN: 4061905063077 Brand: Metav IndustryLine Label: Gauge pin, single, 9.06 mm ±0.001 mm, 50 mm length Facts Diameter: 9.06 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.029 kg Special features Material: special steel Workshop execution Single test pin Ground length for stable seating FAQ What is the intended use for this gauge pin? The gauge pin M323.906 from Metav IndustryLine is intended as a precise reference for pass/fail checks, bore verification and fixture alignment in workshop and inspection environments. How does the ±0.001 mm tolerance affect measurement reliability? A tolerance of ±0.001 mm ensures the gauge pin provides a narrowly defined reference so that measurement variability is minimised, improving reliability in comparative inspection tasks with the Metav IndustryLine test pin. Is the material suitable for repetitive contact checks? Yes; the part is made from special steel and the Metav IndustryLine manufacturing ensures a surface and hardness profile suitable for frequent contact inspections without rapid wear. Can this pin be used as a master for calibration routines? As a single reference element, the Metav IndustryLine gauge pin M323.906 is suitable for routine verification and as a comparative master within controlled calibration workflows. What documentation accompanies the product? The product is supplied with traceable identification (SKU and GTIN) allowing inclusion in QA records; consult Metav Werkzeuge for details on calibration certificates or batch documentation Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.07mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
High‑precision probe for repeatable end‑measurements: the 9.07 mm diameter with ±0.001 mm tolerance and 50 mm length delivers stable, reproducible results for workshop inspection tasks. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.907 — 9.07 mm, ±0.001 mm tolerance (Metav IndustryLine) The Test pin M323.907 is a single, workshop‑grade gauge pin intended for accurate end‑measurements and calibration checks in inspection and assembly environments. Diameter 9.07 mm with ±0.001 mm tolerance Rigid 50 mm length for stable probing Special steel construction for long service life Supplied in transport box for safe handling Consistent end‑measurements that support quality control High repeatability is essential in measurement routines; the combination of a precise 9.07 mm shaft and ±0.001 mm tolerance ensures minimal measurement scatter when checking finished parts or gauges. The narrow tolerance reduces uncertainty in pass/fail decisions and supports statistical process control, meaning fewer downstream rejects and clearer traceability in inspection documentation. The robust geometry keeps the contact point concentric, which simplifies comparison between successive measurements. Designed for reliable workshop use and easy handling A 50 mm length offers a balance between reach and rigidity, reducing flex during probing operations and making the pin suitable for both bench and fixture use. The special steel construction provides mechanical strength that tolerates routine handling, while the workshop‑grade finish eases cleaning and prevents build‑up that can affect readings. Supplied in a protective transport box, the item arrives ready for safe storage and immediate integration into existing inspection kits. Integration into measurement workflows and maintenance of accuracy The single‑piece design is straightforward to incorporate into calibration checks, go/no‑go fixtures or as a reference for dimensional verification. Low mass and compact form factor facilitate fast mounting and changeover in gauge assemblies. Regular inspection of the contact face and documented handling procedures will preserve the ±0.001 mm accuracy over time, helping maintain consistent measurement quality across shifts and operators. For dependable precision and workshop compatibility, request the M323.907 from Metav Werkzeuge — contact our advisors at info@metav-werkzeuge.com or call +49 2822 7131930 for specification advice and dispatch from Emmerich Technical data Article number: M323.907 GTIN: 4061905063084 Brand: Metav IndustryLine Facts Diameter: 9.07 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.029 kg Special features Material: Special steel Workshop design Supplied in transport box Single test pin FAQ What is the intended use of this test pin? The M323.907 test pin from Metav IndustryLine is intended for precise end‑measurements, calibration checks and use in go/no‑go fixtures where a 9.07 mm reference diameter with ±0.001 mm tolerance is required. Is the material suitable for routine workshop handling? Yes; the probe pin is manufactured from special steel, which gives the M323.907 the mechanical strength needed for regular workshop use while maintaining dimensional integrity. How should the pin be stored to preserve accuracy? Storage in the supplied transport box is recommended to protect the M323.907 from knocks and contamination; periodic cleaning of the contact face will help maintain the specified ±0.001 mm accuracy. Can the pin be used for calibration of other gauges? The single, high‑accuracy nature of the M323.907 makes it suitable as a reference element in calibration checks and comparative inspections when traceable references are not otherwise available. Are replacement or matched sets available for serial inspection tasks? Matched sets and additional sizes are commonly used alongside the M323.907 to streamline serial inspection workflows; consult Metav IndustryLine product listings for compatible sizes and set options. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.08mm Test Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Benefit from exacting ±0.001 mm tolerance and a 9.08 mm diameter in a compact, workshop-grade design that supports reliable end‑measure checks and fixture set‑up; order the gauge pin directly via Metav Werkzeuge or contact our consultants for technical advice. Gauge pin M323.908 — 9.08 mm, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) The gauge pin M323.908 is a workshop-grade cylindrical test pin for precision end‑measure verification and fixture alignment in inspection and assembly processes Precision tolerance ±0.001 mm Diameter 9.08 mm, length 50 mm Made from special steel workshop grade Supplied in protective transport box Increase inspection confidence with micron-level precision The gauge pin delivers a defined ±0.001 mm tolerance (equivalent to 1 µm) that supports high‑precision comparative checks and go/no‑go verifications. Such a fine tolerance reduces ambiguity in pass/fail decisions and helps to maintain stable quality gates in production. The narrow allowance is particularly beneficial where small dimensional deviations cause functional issues; by specifying a pin with this accuracy, inspection throughput becomes more predictable and corrective actions more targeted. The controlled dimensional stability also eases integration into existing measurement routines and traceable inspection plans. Robust workshop design for sustained accuracy Manufactured from special steel, this workshop‑grade pin balances hardness and corrosion resistance to withstand routine handling without rapid wear. The material choice contributes to long‑term dimensional stability, which preserves the original tolerance over repeated use. The relatively low mass and compact geometry reduce the risk of accidental bending during handling, while the proven finish ensures consistent tactile contact in comparative measuring appliances. This combination supports fewer replacements and lower lifetime running costs in busy workshop environments. Compact geometry tailored for fixture and end‑measure tasks With a 9.08 mm diameter and a 50 mm length, the pin is sized for tight bores, locating holes and small fixture components where space is limited. The single‑piece format makes it straightforward to use as a reference mandrel for alignment or as an end‑stop when setting up jigs. Narrow, accurately ground pins are easier to position in stacked or multi‑point checks, improving repeatability when multiple measurements are required across an assembly. The single supply format suits bespoke sets or incremental additions to an inspection kit. Protected delivery and handling for immediate use The item is supplied individually and comes in a protective transport box, which reduces the risk of damage in transit and keeps the reference surface clean until the moment of use. The packaging supports organised storage on the workshop bench or within instrument cases and simplifies inventory handling for procurement and quality staff. Lightweight and compact, the package is convenient to carry between inspection stations and to include in portable measurement kits. Proven partner backing and practical benefits As part of the Metav IndustryLine, the pin benefits from a distribution and quality‑control setup based in Emmerich that prioritises consistency and availability for European workshops. That local quality filter and fulfilment capability supports dependable supply and straightforward replacement policies, adding a layer of commercial reliability to the technical advantages. For engineers and quality technicians requiring defined reference standards during process validation, this rugged, accurate pin is a practical addition to the inspection toolkit. Contact Metav Werkzeuge today to discuss the Metav IndustryLine gauge pin M323.908 and arrange delivery from our Emmerich facility — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: M323.908 GTIN: 4061905063091 Label: Gauge pin, single, 9.08 mm, ±0.001 mm, length 50 mm Facts Diameter: 9.08 mm Length: 50 mm Tolerance: ±0.001 mm (1 µm) Weight: 0.029 kg Special features Material: special steel Workshop-grade version Supplied individually in a protective transport box Category: Gauge pins FAQ What tolerance does this gauge pin offer? The gauge pin M323.908 is specified to ±0.001 mm tolerance, corresponding to a 1 µm specification suitable for fine comparative checks. What material is used for this test pin? This Metav IndustryLine test pin is made from special steel, chosen for dimensional stability and wear resistance in workshop environments. How is the gauge pin supplied and protected in transit? The pin is supplied individually and delivered in a protective transport box to prevent handling damage and to keep the reference surface clean. Is this pin suitable for fixture set‑up and small bore inspection? Yes — the 9.08 mm diameter and 50 mm length make the pin appropriate for locating, alignment and end‑measure checks in compact fixtures and small bores Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.09mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of micrometre-level tolerance, workshop-grade special steel and a compact 50 mm length for rapid, repeatable end-dimension checks; order the gauge pin directly via Metav Werkzeuge or consult our technical advisers for application advice. Gauge pin M323.909 — 9.09 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A gauge pin M323.909 designed for precise end-dimension verification and robust workshop use, ideal for go/no‑go controls and fine inspection tasks. 9.09 mm diameter with ±0.001 mm tolerance 50 mm length for compact handling Special steel construction for increased durability Supplied in a protective case for safe transport Micron-level accuracy for reliable go/no‑go checks The pin delivers an exacting ±0.001 mm tolerance, which corresponds to a micrometre‑level accuracy required for critical end‑dimension inspection. Such precision simplifies acceptance testing: a single pin can be used to confirm whether a bore or feature meets the target diameter without complex setup. The high resolution reduces measurement uncertainty and shortens inspection cycles, helping to maintain a consistent production flow while supporting quality control regimes. Robust workshop design that withstands daily use Constructed from special steel and produced as a workshop version, the pin balances wear resistance with dimensional stability. The compact 50 mm length and the nominal 9.09 mm diameter make handling straightforward during repetitive checks, and the component’s low mass supports fast insertion and removal in fixtures. The mechanical design focuses on repeatability and service life, so routine checks remain dependable under standard workshop conditions. Practical supply and handling for immediate use Delivered as a single, individually marked unit and packaged in a protective case, the pin arrives ready for storage or transport. The packaging reduces the risk of handling damage and keeps the gauge pin traceable between shifts and across inspection stations. Clear identification codes and the GTIN ensure straightforward inventory control and integration into existing inspection suites. Integration with inspection workflows and traceability The model is suited for straightforward in‑process checks and end‑of‑line verifications where a defined nominal diameter must be confirmed rapidly. Marked for traceability and supplied by a recognised brand, the pin supports documented quality procedures and helps to standardise inspection steps across teams. For applications requiring serial checks of final dimensions, this compact gauge pin is an efficient tool that complements existing metrology equipment. Contact Metav Werkzeuge for technical matching, batch availability and application guidance — eMail info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the M323.909 and suitable inspection setups Technical Data SKU: M323.909 GTIN: 4061905063992 Brand: Metav IndustryLine Category: Gauge pins Facts Diameter: 9.09 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.029 kg Special features Workshop version Material: special steel Supplied as single piece in protective case Individual packaging for transport safety FAQ What level of precision does the pin provide? The pin offers a precision of ±0.001 mm; the M323.909 from Metav IndustryLine is intended for micrometre‑class end‑dimension checks. Is the pin ready for immediate use out of the box? Yes, the gauge pin M323.909 is supplied as a single, labelled unit in a protective case, ready for integration into inspection routines. Which materials is this pin intended to check? The pin is a dimensional reference for gauges and bores; it is material‑agnostic in use and suitable wherever a nominal 9.09 mm check pin is required. How is the product identified for inventory and traceability? The M323.909 is supplied with a GTIN (4061905063992) and the SKU M323.909 for simple tracking and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.10 mm Precision Gauge Pin ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm tolerance, a compact 9.10 mm diameter and a 50 mm length for precise end‑measurement checks and dependable locating tasks; order the gauge pin directly via Metav Werkzeuge or ask the consultants for application advice. Metav IndustryLine Gauge Pin M323.910 — 9.10 mm diameter, ±0.001 mm tolerance The Gauge pin M323.910 is a single workshop test pin designed for high‑precision end‑measure verification and repeatable go/no‑go checks in small‑component and fixture work. Workshop version, robust design Diameter 9.10 mm, tolerance ±0.001 mm Length 50 mm for reliable positioning Supplied in protective transport box Precision where small differences matter The workshop‑grade gauge pin is manufactured from special steel and specified to a tight ±0.001 mm tolerance, making it suitable for measurements where micrometres decide conformity. This level of accuracy reduces rework and speeds up inspection loops by providing a stable reference for bore verification and assembly trials. The compact 9.10 mm diameter and solid 50 mm length ensure reliable seating in fixtures and minimise elastic deflection; treated as a micro‑class measuring element, it addresses fine mechanical tasks such as small‑part locating and dimensional confirmation with predictability and low measurement uncertainty. Designed for everyday workshop verification Built as a workshop execution item, the pin combines rugged handling properties with dimensional stability. The moderate length allows quick insertion and removal during serial checks while preserving positional repeatability in chucks, fixtures or locating plates. Because the component is made from special steel, wear resistance is improved compared with untreated pins, extending service life in daily quality routines. The simple geometry avoids unnecessary handling complexity and integrates directly into established go/no‑go and reference procedures, so measurement throughput can improve without additional tooling changes. Integration into quality workflows and traceable inventory As a standardised measuring element, the pin supports fast visual and tactile inspection and can be recorded in an internal tooling register for traceability. The article is supplied in a protective transport box, which aids safe storage and prevents damage during transit — an important aspect for maintaining tolerances over time. The clear identification (GTIN and article number) simplifies procurement and inventory management for production and inspection departments. Choosing a robust workshop gauge from a steady supplier reduces the risk of supply‑chain surprises and contributes to consistent, documented measurement practice across shifts and sites. For workshop‑grade measuring assurance and purchase details, contact Metav Werkzeuge in Emmerich to secure the M323.910 gauge pin and discuss suitability for specific fixtures and inspection routines Technical data Article number: M323.910 GTIN: 4061905064005 Category: Gauge pin / Test pin Facts Diameter: 9.10 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.03 kg Special features Material: Special steel Workshop execution Supplied in protective transport box Intended for end‑measure verification and locating tasks FAQ What tolerance does the Metav IndustryLine gauge pin offer? The Metav IndustryLine gauge pin M323.910 is specified to a tolerance of ±0.001 mm, suitable for high‑precision end‑measure checks and tight go/no‑go assessments. Which material is used for this test pin? The M323.910 is made from special steel, chosen to balance wear resistance and dimensional stability for workshop use. How is the gauge pin supplied for transport and storage? The pin is supplied in a protective transport box to prevent damage and to maintain the specified tolerance during handling and storage. What measurement tasks is this pin suited for? The gauge pin is intended for end‑measure verification, locating in fixtures and standard go/no‑go inspections on small components and assemblies. Which workshop class does the pin belong to? With a 9.10 mm diameter and compact length, the pin is treated as a micro‑class measuring element, ideal for fine mechanical tasks and small‑part verification (M323.910). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.11mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of a workshop-grade pin that combines extreme dimensional accuracy (±0.001 mm) with compact handling and robust special steel construction; the 50 mm length facilitates repeatable end‑dimension checks while protected transport in a dedicated box preserves measurement quality — order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single — 9.11 mm, ±0.001 mm (M323.911) by Metav IndustryLine A single gauge pin (9.11 mm) designed for precise end‑dimension verification and fine assembly checks in workshop and inspection environments. Workshop execution for daily shop use Diameter 9.11 mm with ±0.001 mm tolerance Robust 50 mm length in special steel Delivered in a transport box for protection Precise end‑dimension checks for micro applications The compact design addresses the Micro range of gauges (max. 10–100 mm), making this pin ideal where short jaws and low bending are essential. With a diameter of 9.11 mm and a guaranteed deviation of ±0.001 mm, the pin enables highly reproducible limit and reference measurements on small parts and assemblies. Such accuracy reduces measurement scatter during short‑reach inspections and supports reliable pass/fail decisions in production. Durable construction that simplifies handling Manufactured from special steel, the pin offers workshop‑oriented robustness while remaining easy to manipulate thanks to its 50 mm body length. The combination of a slim profile and solid material ensures stiffness for contact probing and insertion into tight bores without excessive flex. Delivery in a protective transport box keeps the surface condition intact between uses, preserving the calibrated state for longer and reducing handling damage during storage and transit. Integration into inspection workflows and traceable supply As a dedicated end‑dimension tool, the pin suits use in fixture checks, go/no‑go assemblies and reference stacks where a minimal uncertainty of ±0.001 mm matters. The simple cylindrical geometry allows quick pairing with micrometre benches, comparator systems or custom gauges, while its consistent diameter supports interchangeability within a set. Supplied under the Metav IndustryLine range, the component benefits from the supplier’s focus on accessible precision and dependable workshop supply chains. For workshop‑grade end‑dimension verification, request the Metav IndustryLine gauge pin M323.911 from Metav Werkzeuge in Emmerich — contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and availability Technical data Article number: M323.911 GTIN: 4061905064012 Manufacturer: Metav IndustryLine Designation: Gauge pin, single, 9.11 mm, ±0.001 mm, length 50 mm Core data Diameter: 9.11 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.03 kg Measurement range: 9.11 mm (single value) Special features Workshop execution Material: special steel Delivered in transport box for protection Category: gauge pins (messstifte) Intended use: end‑dimension verification (endmasse) FAQ What is the intended application for this gauge pin? The gauge pin M323.911 is intended for precise end‑dimension verification and reference checks in workshop inspection tasks and small‑part assembly controls. How accurate is the diameter of the gauge pin? The diameter is specified as 9.11 mm with a permitted deviation of ±0.001 mm, enabling repeatable limit measurements in fine mechanical contexts. Is the pin suitable for use in inspection fixtures and comparator systems? Yes; the rigid 50 mm length and uniform cylindrical geometry allow straightforward integration into fixtures, comparator set‑ups and reference stacks. What material is used and how does that affect durability? Made from special steel, the pin provides a balance of surface hardness and toughness suitable for routine workshop handling and contact probing. How is the pin supplied and protected during transport? The gauge pin is delivered in a protective transport box to guard the measuring surface and ensure the tool arrives in optimum condition. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.12mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of a compact, highly accurate inspection tool that combines ±0.001 mm repeatability, a nominal Ø 9.12 mm, and a durable 50 mm shaft for reliable end‑measure checks; order directly via Metav Werkzeuge or contact the in‑house consultants for specification support. M323.912 Gauge pin (single) — Ø 9.12 mm, ±0.001 mm (Metav IndustryLine) M323.912 Gauge pin (single) is a precision inspection pin for workshop verification of hole diameters and end measurements, designed for straightforward use in routine quality checks and assembly control. Precision tolerance ±0.001 mm Diameter nominal 9.12 mm Length 50 mm for through measurements Workshop version, robust construction Consistent, traceable precision that reduces rework and rejects This inspection pin offers ±0.001 mm tolerance on a nominal 9.12 mm diameter, delivering a fine measurement standard for control points in production and assembly. The extremely close tolerance supports reliable go/no‑go checks and end‑measure verification, reducing the need for follow‑up checks and lowering scrap rates. As a compact measurement artefact, the pin is particularly suited for small‑bore inspection where dimensional certainty directly improves process efficiency and throughput. The marked conformity of the tolerance provides a clear, quantifiable basis for quality decisions. Built for everyday workshop use with durable construction Manufactured from special steel, the pin is supplied in a workshop version that balances handling convenience with service durability. The 50 mm shaft length ensures access into typical component depths while remaining simple to manoeuvre on benches and in fixtures; at 0.03 kg the artefact is easy to position without inducing operator fatigue. Delivery includes a transport box for secure handling and safe transit between workstations, preserving the measuring surface and maintaining the pin’s functional condition over repeated cycles. Easy to integrate into inspection routines and gauge sets The test pin is ideal for inclusion in existing inspection sets and can serve as a reference for quick dimensional checks during processing and final inspection. Where repeatable end measurements are required, this single gauge pin complements fixed gauges and portable measuring equipment, supporting faster decision cycles on the shopfloor. The compact format and robust material permit straightforward storage and handling, while the clear technical specification simplifies documentation of measurement procedures. For traceability and procurement, the article is listed under SKU M323.912. For precise workshop inspection needs choose the Metav IndustryLine gauge pin M323.912 — contact Metav Werkzeuge for tailored advice and order support at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.912 GTIN: 4061905064029 Manufacturer: Metav IndustryLine Facts Diameter: 9.12 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.03 kg Special features Material: Special steel Version: Workshop execution Delivery: Includes transport box FAQ What is the declared tolerance of this gauge pin? The declared tolerance of the M323.912 gauge pin is ±0.001 mm, suitable for fine inspection and end‑measurement tasks. Is the pin suitable for bore verification in production? Yes; the inspection pin from Metav IndustryLine is intended for workshop bore and end‑measure verification and supports quick go/no‑go assessments. What material is the gauge pin made from? The M323.912 is manufactured from special steel chosen for durability in frequent workshop use. How long is the shaft and what applications does that cover? The shaft length is 50 mm, which covers typical component depths encountered in assembly and small‑part inspection. Is the product supplied ready for safe transport and storage? Delivery of the inspection pin includes a transport box to protect the measuring surfaces during handling and transit. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.13mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, micrometre-level tolerance and a compact 50 mm length for dependable end‑size checks in workshop and inspection routines. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin M323.913 — 9.13 mm, ±0.001 mm tolerance (Metav IndustryLine) A single precision gauge pin designed for fine end‑size measurements and workshop inspection tasks in the micro measurement range. Workshop-grade special steel construction High accuracy ±0.001 mm Diameter 9.13 mm for end‑size checks Compact 50 mm length for precise positioning Consistent precision for end‑size verification The gauge pin provides ±0.001 mm repeatability, making it suitable where narrow tolerance windows decide pass or fail. Manufactured for the micro range, the geometry minimises bending and supports reliable contact during end‑measurements. This performance reduces measurement uncertainty and shortens inspection cycles, which in turn improves throughput in small‑component inspection or assembly control. The result is a noticeable reduction in rework and a clearer statistical basis for process decisions. Durable workshop construction that keeps accuracy Built from special steel in a workshop execution, the pin resists handling wear while retaining measurement integrity. The 50 mm shank length and a 9.13 mm diameter offer good stiffness for single‑operator probing and fixture use. Where repeated insertion and removal are routine, material choice and heat treatment ensure surface stability and long service life; maintenance is limited to routine cleaning and visual inspection, helping to keep downtime low. Easy integration into quality workflows The plug‑style design suits insertion into gauges, jigs or bore checks and complements existing inspection sets. Its compact dimensions allow close placement in fixtures without obstructing other gauges or sensors. Traceability is supported by clear labelling (SKU M323.913, GTIN provided in technical data), and handling is straightforward: the component can be used as a reference pin for go/no‑go checks or as a datum in comparative setups, helping standardise measurement procedures across shifts. Contact Metav Werkzeuge for tailored advice on implementing the M323.913 gauge pin in inspection fixtures or for procurement assistance at the next production stop Technical Data SKU: M323.913 GTIN: 4061905064036 Category: Gauge pin (Messstifte) Facts Diameter: 9.13 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.03 kg Special features Material: Special steel Workshop execution Single gauge pin Designed for end‑size measurements FAQ What is the declared tolerance of this gauge pin? The gauge pin M323.913 is specified with a tolerance of ±0.001 mm, suitable for tight end‑size verification. Can this pin be used in assembly jigs and inspection fixtures? Yes, the workshop execution and compact 50 mm length make the pin appropriate for jigs, fixture inserts and go/no‑go checks. What material is the pin made from and how does that affect wear? Manufactured from special steel, the pin balances hardness and surface stability to resist wear during repeated use. Is the diameter standardised for common bore checks? The nominal diameter of 9.13 mm is intended for precise end‑size checks and integration with inspection tooling commonly used for small components. Where can technical advice or procurement be obtained? Technical advice and procurement support are available via Metav Werkzeuge; please reach out for application guidance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.14mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Benefit from workshop‑grade precision, a stable 50 mm working length and a tight tolerance of ±0.001 mm to secure repeatable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for tailored inspection advice. Gauge pin M323.914 — Single gauge pin, 9.14 mm ±0.001 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.914 serves as a compact, workshop‑grade reference pin for fast end‑dimension checks and GO/NO‑GO verifications in production and quality control Workshop-grade accuracy ±0.001 mm 9.14 mm reference diameter, 50 mm length Special-steel construction for consistency Repeatable precision for routine inspection A tolerance of ±0.001 mm places this reference pin in the realm of high‑precision workshop tools, suitable where micrometric repeatability matters. The tight tolerance reduces measurement uncertainty when used as a master for end‑dimension checks or as a reference in fixture verification. By using a single, dedicated reference pin made of special steel, inspection routines gain a consistent datum that shortens decision cycles and lowers the risk of rework. The numerical accuracy supports rational process decisions and faster throughput on production lines without speculative claims about calibration beyond the supplied data. Robust form factor that supports handling and stability With a nominal diameter of 9.14 mm and a length of 50 mm, this reference pin offers a compact but sufficiently long contact area for reliable placement and tactile handling. The modest mass and balanced geometry make the pin easy to position in bores or jigs while keeping bending and seating errors negligible for short end‑measure checks. The special‑steel composition gives dimensional stability across typical workshop temperature ranges and repeated use, delivering the mechanical reliability required in daily quality inspections and benchwork. Practical integration into inspection workflows As a single reference element, the pin is intended for direct comparison and quick GO/NO‑GO checks, supporting lean inspection workflows and minimising machine downtime. When incorporated into fixture checks, sample control or incoming inspection, the pin enables straightforward decisions based on objective measurements rather than subjective estimates. For teams looking to harmonise results across several workstations, the consistent geometry of this reference helps standardise procedures and reduce variance between operators. If configuration advice or selection between reference sizes is required, Metav’s consultants can provide practical guidance tailored to the task and environment. Built for the workshop, supplied for immediate use Designed as a workshop version, the pin is supplied as a single unit for rapid deployment at the inspection bench. The compact format suits production screening, toolroom tasks and quick verification of end‑cases without adding organisational complexity. The robust material choice and clear dimensional information support confident specification and procurement decisions, while the brand backing ensures availability from a European quality filter that serves industrial and craft customers alike. Contact Metav Werkzeuge for application advice or to order the M323.914 gauge pin from our Emmerich stock and secure a reliable reference solution for daily inspection tasks Technical Data Article number: M323.914 GTIN: 4061905064043 Brand: Metav IndustryLine Facts Diameter: 9.14 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.03 kg Special features Workshop version Material: Special steel Single unit delivery FAQ What is the stated measurement tolerance of this reference pin? The M323.914 gauge pin (Metav IndustryLine) has a tolerance of ±0.001 mm, providing high‑precision reference performance for end‑dimension checks. For which inspection tasks is this reference pin intended? This single gauge pin is intended for end‑measure checks, GO/NO‑GO verifications and quick fixture or incoming inspection comparisons where a stable reference diameter is required. Is the item delivered individually or as part of a set? The product is supplied as a single reference pin under the article number M323.914 for immediate use in workshop inspection routines. Can the pin be used as a master for GO/NO‑GO checks in production? Yes, the M323.914 serves as a reference master for GO/NO‑GO procedures and can be incorporated into simple pass/fail checks or fixture verification workflows. How should the reference pin be cared for to maintain accuracy? Handle the pin by its shank, protect contact surfaces from contamination, store in a dry place and avoid impacts; the special‑steel construction supports dimensional stability under normal workshop conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.15mm Gauge Pin Single, ±0.001 mm, Length 50mm, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of high‑precision tolerance and a compact, workshop-ready design to ensure fast, repeatable inspection of end dimensions; the minimal form factor and special steel construction reduce wear and setup time. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for specification matching. Gauge pin M323.915 – 9.15 mm, ±0.001 mm, 50 mm by Metav IndustryLine The gauge pin M323.915 is a compact precision pin for end‑dimension inspection and fixture verification in workshop and production environments Workshop version, robust finish Diameter 9.15 mm with ±0.001 mm tolerance Length 50 mm for fixture and gauge use Special steel for wear resistance Precision that reduces measurement uncertainty When measurement tolerance matters, a sub‑millimetre allowance quickly determines accept/reject decisions. The gauge pin specified here gives a declared tolerance of ±0.001 mm, which corresponds to a 1 µm window—suitable where micron‑level conformity is required. Such a fine allowance reduces subjective judgement in manual checks and lowers the rate of rework by ensuring that mating bores, pins and reference features are assessed against a tight, verifiable standard. The compact 9.15 mm diameter concentrates rigidity in a small form, which supports highly repeatable contact during sequential checks. Workshop design for fast, repeatable inspection A straightforward geometry and a 50 mm length make this pin convenient for fixture validation, go/no‑go checks and end‑measurement tasks without excess overhang. The Workshop version finish is engineered for everyday handling and integration into inspection benches or assembly jigs; the short, rigid form reduces bending and improves tactile control. Where throughput and cycle time are priorities, the combination of small mass and robust material shortens positioning time and stabilises contact, delivering measurable gains in inspection speed while maintaining precision. Material selection and practical integration into quality systems Constructed from special steel, the pin balances wear resistance with corrosion stability expected in shop environments. The compact design is particularly useful for fine‑mechanical assemblies and small bore inspection, aligning with the micro‑scale inspection category that prioritises minimal deflection and high repeatability. Identification via SKU and GTIN supports traceability and inventory control: use the SKU M323.915 and GTIN 4061905064050 to integrate the item into existing quality documentation and parts lists, avoiding ambiguity during audits or batch inspections. Contact Metav Werkzeuge today for specification checks and supply from Emmerich—Metav IndustryLine delivers workshop‑grade precision ready for immediate use Technical data SKU: M323.915 GTIN: 4061905064050 Label: Prüfstift, einzeln, 9,15mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 9.15 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.03 kg Special features Material: special steel Execution: workshop version Intended use: end‑dimension inspection and fixture checking Accuracy class: ±0.001 mm FAQ What level of accuracy does the pin provide? The gauge pin M323.915 is specified with a tolerance of ±0.001 mm, equivalent to 1 µm, suitable for high‑precision inspection tasks. For which inspection tasks is this pin suitable? Typical uses include end‑dimension verification, fixture validation and go/no‑go checks where a compact, rigid reference pin is required. Is the material indicated for everyday workshop use? Yes. The component is made from special steel, selected to offer wear resistance and robustness for repeated handling in a workshop environment. How can the item be identified in stock and documentation? Use the SKU M323.915 and GTIN 4061905064050 for unambiguous identification in inventory systems and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.16mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑tight ±0.001 mm tolerance, a precise 9.16 mm diameter and a compact 50 mm length for fast, repeatable end‑dimension checks; order the part directly via Metav Werkzeuge or contact our consultants for application advice. M323.916 precision gauge pin — single plug gauge, 9.16 mm, ±0.001 mm The M323.916 is a single precision gauge pin designed for end‑dimension inspection and go/no‑go verification in workshop and production metrology. Workshop version for robust everyday use Diameter 9.16 mm with ±0.001 mm accuracy 50 mm overall length for standard setups Made from special steel for wear resistance Consistent precision for end‑dimension inspection The M323.916 functions as a high‑precision gauge pin for routine verification of finished dimensions. With a specified tolerance of ±0.001 mm, the plug is suited to applications where repeatability and minimal measurement uncertainty are essential. The nominal 9.16 mm diameter and smooth cylindrical form provide reliable contact during insertion checks; this reduces interpretation time and supports quick go/no‑go decisions on the shop floor. By choosing a tool with such fine tolerance, inspection processes become more deterministic, lowering the risk of rework and production rejects. Robust design that fits everyday workshop workflows Manufactured from special steel, the pin balances hardness and toughness for extended life under frequent use. The 50 mm overall length offers a practical grip and engagement depth for standard fixtures and pin holders while keeping handling straightforward during manual checks. The workshop variant emphasises durability and serviceability: the geometry resists deformation and the surface finish minimises wear on mating holes. As a single, purpose‑made test pin, it integrates easily into check fixtures, comparator stands or simple handheld inspections without the need for complex adapters. Increased throughput through dependable measurement practice Adopting this precision plug accelerates inspection routines by providing a single, unambiguous reference for end‑dimension checks. The narrow tolerance makes the pin suitable for final checks in precision assemblies and small‑batch production where dimensional conformity is critical. The resulting reduction in inspection variability supports downstream efficiency gains: fewer stoppages for investigation, faster acceptance cycles and clearer quality records. When combined with a disciplined inspection protocol, the gauge pin contributes directly to process reliability and product conformity. For procurement or technical alignment, contact Metav Werkzeuge to source the Metav IndustryLine M323.916 precision gauge pin and discuss how it fits existing inspection routines at our Emmerich facility Technical data Article number: M323.916 GTIN: 4061905064494 Brand: Metav IndustryLine Material: Special steel Diameter: 9.16 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.03 kg Facts Diameter: 9.16 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.03 kg Special features Workshop execution Single gauge pin for end‑dimension checks Robust geometry for repeated use Compact form factor for fixture compatibility FAQ What is the diameter and tolerance of the gauge pin? The M323.916 gauge pin has a nominal diameter of 9.16 mm with a tolerance of ±0.001 mm, making it suitable for precise end‑dimension verification. What material is used for this plug gauge? This Metav IndustryLine plug gauge is made from special steel, selected for wear resistance and stable dimensional performance in routine workshop use. How long is the test pin and how does this affect handling? The overall length is 50 mm, which provides sufficient engagement for most fixtures while remaining easy to handle during manual inspections. Can the M323.916 be used in production go/no‑go checks? Yes, the precision and form of the M323.916 make it appropriate for straightforward go/no‑go and insertion checks in production and assembly areas. Is the gauge pin compatible with standard pin holders and fixtures? The compact cylindrical design of the M323.916 is intended to be compatible with conventional pin holders and simple fixture arrangements used in workshop metrology. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.17mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra-fine measurement accuracy (±0.001 mm) and a rigid 9.17 mm diameter for repeatable end‑measurement references; the 50 mm shaft length and special‑steel construction ensure durability in workshop conditions. Order the M323.917 directly via Metav Werkzeuge or consult our specialists for application advice. M323.917 Test pin — precision 9.17 mm, tolerance ±0.001 mm (Metav IndustryLine) The M323.917 is a precision test pin designed for end‑measurement and gauging tasks in industrial metrology, providing a compact reference for inspection and fixture verification. Precision tolerance ±0.001 mm Nominal diameter 9.17 mm 50 mm length in special steel Consistent metrology through sub‑micrometre tolerance The core advantage of this gauge pin is its ±0.001 mm tolerance, which delivers a level of reproducibility suited to high‑precision inspection and end‑dimension control. A stable nominal diameter of 9.17 mm acts as a reliable reference in comparative checks and alignment operations; the very low variation minimises recalibration cycles and reduces scrap through earlier detection of machining drift. This rational advantage leads to measurable gains in quality control throughput and less downtime for repeat measurements. Workshop durability with true measurement stability Constructed from special steel and finished for metrological use, the shaft length of 50 mm balances handling convenience with sufficient engagement for internal and external gauging. The workshop configuration emphasises robustness under frequent use: wear‑resistant material and a stiff shaft reduce elastic deflection during contact measurements, ensuring that each contact transfers force consistently. As a result, the test pin maintains geometry over many inspection cycles, preserving accuracy and lowering total cost of ownership. Easy integration into inspection workflows Designed as a single inspection pin for end‑mass and gauging applications, this component fits into a wide range of fixtures and comparator set‑ups. Identification via SKU M323.917 and GTIN enables traceability in stock lists and quality records, supporting traceable batch control. The compact mass facilitates quick handling while the nominal diameter simplifies substitution in modular jigs. For workshops aiming to raise first‑pass yield, the combination of tight tolerance and robust material offers a clear, efficiency‑driven benefit. Contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com for application advice and delivery options for the M323.917 precision test pin Technical data Article number: M323.917 GTIN: 4061905064500 SKU: M323.917 Weight: 0.03 kg Facts Diameter: 9.17 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.03 kg Special features Workshop version (Werkstatt‑Ausführung) Single test pin for end‑measure references Material: Special steel High repeatability for inspection tasks FAQ What level of accuracy does this inspection pin provide? The inspection pin offers an accuracy of ±0.001 mm, making the M323.917 suitable for high‑precision end‑dimension checks and repeatable gauging tasks. Which materials is the shaft made from and why does that matter? The shaft is manufactured from special steel; this material gives the pin good wear resistance and stability, helping to retain geometry under frequent contact measurements. How is the pin typically used in a measurement workflow? The pin serves as a fixed reference for end‑mass and fixture checks, simplifying comparative measurements and enabling quick verification of part dimensions in production. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.18mm Gauge Pin, Workshop Version, ±0.001mm Accuracy, Length 50mm - Metav IndustryLine
Take advantage of the combination of workshop‑grade construction, ±0.001 mm tolerance and secure transport packaging for reliable end‑dimension verification; order the gauge pin directly via Metav Werkzeuge or consult our specialists if further application advice is required. M323.918 Gauge pin – 9.18 mm, ±0.001 mm tolerance (Metav IndustryLine) The M323.918 gauge pin is a single precision test pin designed for repeatable end‑dimension checks and fine workshop metrology. Workshop‑grade construction Tolerance ±0.001 mm (1 µm) Diameter 9.18 mm, length 50 mm Delivered in a protective transport case Achieve repeatable end‑dimension checks with micron accuracy The pin is manufactured for end‑dimension verification where tight tolerances matter. With a stated tolerance of ±0.001 mm (equivalent to 1 µm) the component offers a rational improvement in process control: fewer measurement‑related rejects, clearer go/no‑go decisions and reliable documentation for quality procedures. The very fine tolerance supports precision fits and small‑bore inspections commonly encountered in toolmaking, instrumentation and small‑part assembly, providing an objective basis for quality acceptance. Compact format that suits workshop routines and small components A compact geometry—9.18 mm diameter and 50 mm length—keeps handling intuitive on the shop bench and allows precise insertion into holes or seats without excessive mass or flex. The workshop‑grade build addresses everyday robustness while preserving the small‑part sensitivity required for fine mechanical work. The single‑pin configuration is practical for targeted checks, enabling rapid sequential verification without the handling complexity of multi‑pin sets. Durable material and secure transport for consistent performance Made from special steel, the test pin combines surface integrity with dimensional stability under normal workshop conditions; the chosen alloy ensures resistance to wear in routine inspection tasks. Delivery in a protective case safeguards the measuring face during storage and transport, helping to preserve the pin’s tight tolerance and extend service life. Traceable identifiers and compact packaging simplify inventory management and bench organisation for inspection stations. For workshop‑grade precision and transportable protection, contact Metav Werkzeuge to discuss the M323.918 gauge pin and ordering options via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.918 GTIN: 4061905064517 Brand: Metav IndustryLine Facts Diameter: 9.18 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.03 kg Special features Workshop‑grade construction Made from special steel Single gauge pin, supplied individually Delivered in protective transport case FAQ What is the intended use of this gauge pin? The gauge pin M323.918 by Metav IndustryLine is intended for end‑dimension checks, seating and small‑bore verification in workshop and inspection environments. Is the tolerance of ±0.001 mm suitable for toolmaking? Yes; the ±0.001 mm tolerance (1 µm) makes the pin appropriate for toolmaking and precision assembly tasks where micron‑level accuracy is required. What material is the pin made from and why does it matter? The pin is made from special steel, selected to provide dimensional stability and surface durability for routine inspection operations. How is the pin supplied and protected during transport? The gauge pin is supplied individually and delivered in a protective transport case to prevent damage to the measuring face and to maintain accuracy. Can this pin be used for go/no‑go gauging or only for measurement? While primarily a precision test pin for measurement and fit verification, the M323.918 can support go/no‑go checks when incorporated into a gauging setup or used as a reference for seat fits. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.19mm Gauge Pin ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of high-precision tolerance (±0.001 mm) combined with a compact 50 mm length and robust workshop design for dependable end‑measurement tasks; order directly via Metav Werkzeuge or consult our specialists for application advice. M323.919 Gauge pin — 9.19 mm, ±0.001 mm, Metav IndustryLine The M323.919 gauge pin is a workshop‑grade plug for precise end‑measure checks, providing micron‑level conformity in small‑part inspection. Workshop-grade accuracy ±0.001 mm Diameter precisely 9.19 mm Length 50 mm for end‑measure checks Delivered in protective transport case Precision that secures repeatable inspection results The central benefit of this plug gauge is its ±0.001 mm nominal tolerance, equivalent to 1 µm, which positions it for use where minimal deviation is critical. Such a tolerance ensures that the dimension used as a reference remains stable across repeated cycles, reducing rework and scrap rates in small‑part production. The specified diameter of 9.19 mm is held to this tight limit, enabling reliable pass/fail decisions when checking end masses or mating bores. Where traceable dimensional control is required, this degree of accuracy forms a measurable basis for process control and documentation. Built for workshop handling and long‑term serviceability Constructed from special steel, this single‑piece pin combines wear resistance with manageable mass for handheld inspection and fixture use. With a 50 mm overall length, the gauge balances reach and rigidity, permitting secure seating in end‑measure operations without excessive flex. The unit is supplied as a workshop‑grade article and arrives in a protective transport case, which simplifies storage and minimises the risk of handling damage between uses. These attributes support a smooth inspection workflow and help maintain the reference dimension over time. Practical integration into inspection and setup routines The plug is intended for end‑measurement and reference checking in assembly, jig set‑up and quality control contexts; its single nominal diameter provides a clear, objective check for mating holes and end faces. Its compact form and light weight make it suitable for frequent use at the workbench or on the shop floor, while the consistent tolerance supports interchangeability in fixtures and gauges. For operations that demand predictable, measurable results from a small footprint tool, this plug pin offers a balance of precision, durability and straightforward handling that benefits both shop technicians and quality engineers. For reliable workshop measurement equipment from Metav IndustryLine, contact Metav Werkzeuge to discuss ordering and suitability for specific inspection tasks — info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.919 GTIN: 4061905065040 Category: Gauge pins Manufacturer: Metav IndustryLine Facts Diameter: 9.19 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.03 kg Measuring range: 9.19 mm Special features Workshop execution Made from special steel Delivered in protective transport case Single plug gauge for end‑measure checks FAQ What is the declared tolerance of this gauge pin? The M323.919 gauge pin is specified with a tolerance of ±0.001 mm, corresponding to approximately 1 µm, suitable for high‑precision end‑measure verification. Which materials is the plug gauge suitable for checking? The plug is intended as a dimensional reference; it is made from special steel and is used to check bores and end faces across common workshop materials where precise mating dimensions are required. Is the gauge pin ready for immediate use upon delivery? Yes, the M323.919 is supplied as a ready‑to‑use workshop item and includes a protective transport case to preserve the reference surface during storage and handling. For which tasks is this gauge pin primarily used? This plug gauge is optimised for end‑measure checks, fixture setup and small‑part inspection where a single, highly accurate reference diameter is needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.21mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
A compact inspection solution that combines ±0.001 mm accuracy with a slim 9.21 mm diameter and a 50 mm working length for reliable end‑dimension checks; ideal where repeatable, high‑resolution gauging is required. Order the test pin directly via Metav Werkzeuge or consult our specialists for integration advice. Test pin M323.921 — single inspection pin, 9.21 mm, ±0.001 mm (Metav IndustryLine) A Test pin M323.921 designed for precise end‑dimension verification and fixture use in workshop and laboratory metrology Workshop version, robust construction Diameter precisely 9.21 mm ±0.001 Length 50 mm for fixture compatibility Made from wear‑resistant special steel High‑precision control for end‑dimension checks The inspection pin delivers industrial‑grade dimensional control with a diameter of 9.21 mm and a declared accuracy of ±0.001 mm (equivalent to 1 µm). Such resolution enables confident verification of bore sizes, end‑masses and tight fit tolerances in assembly lines and gauge blocks. The 50 mm overall length provides sufficient engagement for many fixture layouts while keeping the tool compact for rapid handling. These objective specifications support faster decision‑making in quality checks and reduce scrap through reliable pass/fail assessment. Robust design adapted to workshop handling Constructed in special steel, the component is specified as a workshop version and resists wear under repeated seating and small impacts typical in dynamic production environments. The slim profile and a mass of 0.03 kg combine to make the pin easy to position in gauges and carriers without adding unnecessary inertia to delicate fixtures. Mechanical stability and material choice minimise surface deformation, which preserves the tight ±0.001 mm tolerance across many measurement cycles and extends service intervals between replacements. Seamless integration into inspection workflows This single test pin is suitable for incorporation into go/no‑go gauges, plug gauge assemblies and comparative measurement rigs where end dimensions must be reproducible. Traceability is supported by clear identifiers and numerical data for inventory control; the compact format simplifies storage and rapid exchange in multi‑operator environments. Using a defined, high‑precision pin like this reduces measurement variation and streamlines calibration schedules, which in turn improves throughput and lowers rework rates in precision manufacture. Contact Metav Werkzeuge to discuss how the 9.21 mm test pin from Metav IndustryLine can be integrated into existing gauging systems and to confirm availability at our Emmerich centre Technical data Article number: M323.921 GTIN: 4061905065064 Brand: Metav IndustryLine Facts Diameter: 9.21 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.03 kg Special features Category: Test pins Material: Special steel Version: Workshop execution SKU: M323.921 FAQ What applications are suitable for this inspection pin? The inspection pin is intended for end‑dimension verification in gauges, fixture checks and assembly controls; it suits workshop and laboratory metrology tasks requiring micrometre‑level resolution. Is the tolerance of ±0.001 mm achievable in routine use? When used in stable fixtures and with appropriate handling, the ±0.001 mm specification is maintained; adherence to correct seating and calibration routines is essential for repeatable results. Can the pin be used in standard go/no‑go gauges and plug assemblies? Yes, the diameter and 50 mm length make the component compatible with common gauge holders and plug‑gauge designs employed in quality control. How durable is the pin under frequent measurements? Made from special steel in a workshop version, the pin is designed for wear resistance and reliable dimensional retention during regular inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.22mm Gauge Pin 50mm Length ±0.001mm Workshop Version, Special Steel - Metav IndustryLine
Benefit from precise end‑measurement and stable workshop performance thanks to the combination of a 9.22 mm diameter with ±0.001 mm tolerance and a 50 mm overall length; order the single gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.922 — single inspection pin, Ø 9.22 mm, ±0.001 mm (Metav IndustryLine) A gauge pin M323.922 designed for precision end‑measure checks and plug gaging in inspection benches and toolmaking. Workshop-grade single gauge pin, hardened steel Diameter 9.22 mm with ±0.001 mm tolerance 50 mm overall length for end-measure applications Accuracy that preserves measurement chains The pin is manufactured to a ±0.001 mm dimensional tolerance, making it suitable as a reference in high-precision inspection tasks where tight limits are required. This level of accuracy reduces stack‑up uncertainty in gauging routines and supports repeatable results during process checks. The combination of a finely controlled diameter and a stable length ensures that the component can be used as a reliable end measure or gauge shank in comparative inspections and small‑batch quality controls. Durable construction for workshop conditions Built in a workshop-grade design and produced from special steel, the inspection pin combines wear resistance with dimensional stability under normal handling. The 50 mm overall length gives sufficient engagement for end measurements while remaining compact for fixtures and gauge holders. Low mass and robust construction allow frequent use on benches and in measuring fixtures without compromising the nominal dimension, so maintenance intervals are extended and replacement frequency is reduced. Practical integration into inspection systems The geometry and tolerance class make the pin suitable for use as a plug gauge or reference pin within comparative setups and verification rigs. Its single‑piece supply simplifies stockkeeping for dedicated inspection tasks and the clear specification of Ø 9.22 mm and ±0.001 mm supports traceable documentation of inspection equipment lists. Where interchangeability of gauge elements is required, the pin functions as a stable baseline for quick checks and for aligning small bores or mating features. Measurable benefits for production control Employing a defined reference such as this inspection pin improves measurement consistency and shortens decision cycles in quality control. Reduced ambiguity in pass/fail evaluation follows from the tight tolerance, and throughput benefits arise from quicker verification steps at workstations. For precision workshops and toolrooms, the component supports tighter process control and contributes to overall product conformity. For application guidance or to request the Metav IndustryLine M323.922 for integration into inspection fixtures, contact Metav Werkzeuge: phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: M323.922 GTIN: 4061905065071 Category: Messstifte Facts Diameter: 9.22 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.03 kg Special features Material: Special steel Workshop version Single piece delivery Application: end-measure / plug gaging FAQ What tolerance does the gauge pin deliver? The Metav IndustryLine gauge pin M323.922 is specified with a tolerance of ±0.001 mm, suitable for tight comparative inspections. Can the pin be used for plug gaging and end measurements? Yes, the inspection pin is intended for end‑measure applications and plug‑gaging tasks where a stable reference diameter of 9.22 mm is required. What material is the pin made from and how does that affect wear? The pin is produced from special steel, selected for a balance of hardness and dimensional stability to reduce wear in routine workshop use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9.23mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm repeatability on a 9.23 mm test diameter and a robust 50 mm shank for reliable end‑measure checks; order directly from Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.923 — 9.23 mm, ±0.001 mm tolerance (Metav IndustryLine) The gauge pin M323.923 is a single test pin designed for precise end‑measurement and reference checks in workshop metrology and inspection tasks. High-precision ±0.001 mm tolerance Diameter 9.23 mm, ground to nominal size 50 mm length for end and depth checks Supplied in a protective transport case Accuracy that lowers measurement uncertainty The pin offers an exceptional ±0.001 mm positional tolerance, which makes it suitable where tight go/no‑go criteria or fine clearance verification are required. This level of accuracy reduces rework and inspection time by providing a stable reference that can be used in repeatability tests and dimensional spot checks. The high resolution of the gauge pin supports consistent pass/fail decisions in quality control, providing a measurable benefit for production processes that rely on tight fits or end‑measure dimensions. Durable construction for frequent workshop use Manufactured from special steel and presented in a workshop configuration, the test pin is engineered for everyday handling and repeated insertion cycles. The 50 mm shank length delivers a comfortable engagement depth for end‑measure and depth applications while limiting deflection during use. Supplied in a protective transport case, the component remains protected during storage and transit, helping to preserve surface finish and measurement integrity over longer service intervals. Practical integration into inspection routines Marked with its SKU and GTIN for traceability, the gauge pin is straightforward to incorporate into existing inspection routines and fixture checks. The precision ground diameter of 9.23 mm suits dedicated plug checks and reference‑pin tasks where nominal sizes must be confirmed quickly. If specification adaptation or fixture recommendations are required, Metav Werkzeuge’s product information and technical specialists can advise on compatible holders or comparison methods, supporting efficient implementation in serial inspection workflows. Choose the Metav IndustryLine M323.923 for precise end‑measurement references and contact Metav Werkzeuge in Emmerich for tailored technical guidance and prompt dispatch Technical data SKU: M323.923 GTIN: 4061905065996 Brand: Metav IndustryLine Numbers / Core technical data Diameter: 9.23 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.03 kg ECLASS: 21170231 Special features / Versions Workshop version Material: special steel Single gauge pin for end measurements Supplied in protective transport case Suitable for precision reference and go/no‑go checks FAQ What level of accuracy can be expected from this test pin? The M323.923 gauge pin provides an accuracy of ±0.001 mm, delivering a high‑precision reference for fine tolerance inspections and go/no‑go assessments. Which materials is the gauge pin suitable for checking? The gauge pin M323.923 is a dimensional reference tool; it is used to verify hole diameters and end dimensions regardless of workpiece material and is particularly useful in metalworking inspection processes. How should the pin be stored to maintain accuracy? Store the pin in its protective transport case and avoid exposure to corrosive environments; the case supplied preserves the special steel finish and protects the ground diameter from knocks and contamination. Can the pin be used in fixture or jig checks? Yes, the test pin is appropriate for fixture alignment and reference checks where a stable, ground nominal diameter of 9.23 mm is required; the 50 mm length aids secure seating in many standard holders. Is the product traceable for documentation purposes? The gauge pin is supplied with an identifiable SKU and GTIN which supports traceability and inventory management in quality systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com