Precision surface plates for exact measurement and inspection
A precision surface plate provides a stable reference for dimensional inspection and layout, enabling accurate measurement and improved quality control across metalworking and engineering shops. These granite and cast-iron surface plates and their complementary inspection tables are used with height gauges and stands to support repeatable measurements on machined components, delivering flatness and rigidity that reduce setup time and measurement error. Designed for calibration and inspection tasks, the systems enhance process reliability when checking tolerances and part geometry.
800 x 600 mm Scriber Plate Gray Cast Iron, DIN 876/3 - Metav IndustryLine
A heavy, flat reference surface in grey cast iron with an 800 × 600 mm working area and conformity to DIN 876/3 provides a dependable base for layout, inspection and marking work; the plate’s mass and 25 mm section minimise vibration and thermal distortion while ensuring repeatable results. Order the marking plate directly via Metav Werkzeuge or consult our advisers for application recommendations. Marking plate M206.207.1 — Grey cast iron, 800 × 600 mm (DIN 876/3) | Metav IndustryLine The Marking plate M206.207.1 is a grey cast iron measuring surface designed for workshop layout, scribing and inspection tasks where a stable, standardised reference plane is required. Grey cast iron construction Flatness to DIN 876/3 800 × 600 mm working surface Massive 70 kg for stable measurements A stable reference plane that improves measurement repeatability A robust reference surface reduces variability in workshop layout and inspection. The heavy mass and compact section of this plate provide improved damping against incidental vibration, so marks and checks retain positional accuracy. Where repeatable scribing and inspection are essential, a defined flatness class reduces the need for repeated reprofiling of workpieces, supporting faster throughput and lower scrap rates. Conformance to DIN 876/3 for consistent flatness and comparability Being manufactured to DIN 876/3 means the surface meets an established flatness class used in many production and inspection environments. This standardised tolerance makes results comparable across shifts and locations, simplifying process control and documentation. For organisations that rely on predictable geometric references, the plate’s compliance with the norm supports reliable layout and alignment procedures without requiring specialist high‑end metrology. Cast iron advantages: thermal stability and wear resistance Made from grey cast iron, the plate benefits from good thermal properties and inherent damping, which together help to maintain flatness under typical workshop conditions. The specification 800 × 600 × 25 mm describes the usable surface and section thickness; the substantial mass of 70 kg contributes to a steady working surface that resists transient disturbances. These material characteristics make the plate particularly suitable for marking, comparison checks and as a mounting surface for small jigs and fixtures. Practical use cases and workshop integration This plate is optimised for layout, scribing and general measuring‑table duties in machine shops, toolrooms and assembly areas. It serves well as a stable datum for transferring dimensions, checking flatness of small components and as a reference when setting up simple inspection rigs. Supplied as a finished grey cast iron plate, it integrates into existing workshop procedures with minimal additional training and supports efficient, error‑reduced workflows. For precision workshop layout and reliable inspection, request the Metav IndustryLine marking plate from Metav Werkzeuge and arrange delivery or technical advice via our consultants Technical data Article number: M206.207.1 GTIN: 4054469103389 Material: Grey cast iron Standard: DIN 876/3 Tariff code: 90178090 Numbers / Core technical data Dimensions (L × W × H): 800 × 600 × 25 mm Overall height: 100 mm Weight: 70 kg Special features / Versions Category: Measuring table Stable mass for vibration damping Finished surface suitable for marking and scribing FAQ What applications is this marking plate suited for? The Metav IndustryLine marking plate M206.207.1 is intended for layout, scribing, inspection and as a general reference surface in workshops and toolrooms. How does DIN 876/3 affect everyday use? DIN 876/3 defines the plate’s flatness tolerance; using the plate ensures comparable reference results and supports consistent marking and inspection procedures. What benefits does grey cast iron provide for a surface plate? Grey cast iron offers good damping and thermal stability, which help the M206.207.1 maintain flatness and reduce the influence of vibration during marking and inspection. Is the plate heavy to handle and how should it be installed? With a mass of 70 kg the plate is intentionally heavy to improve stability; handling and installation should follow standard workshop safety practices and use appropriate lifting aids. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
800mm x 500mm x 100mm Granite Surface Plate Grade 0, DIN 876/0 - Metav IndustryLine
Benefit from a stable, thermally resistant reference surface with Grade 0 flatness and robust dark granite construction; the combination of proven accuracy and solid mass supports repeatable inspection results. Order the plate via Metav Werkzeuge or consult the Metav team for handling and delivery details. Granite Surface Plate M206.107 — 800 × 500 × 100 mm, Grade 0 (Metav IndustryLine) The Granite Surface Plate M206.107 is a Grade 0 reference surface designed for precision inspection, layout and calibration work in workshop and metrology environments. Grade 0 flatness to DIN 876/0 Solid dark granite for thermal stability Surface 800 × 500 × 100 mm for medium layouts Delivered as plate only, without stand A stable reference for accurate inspection work A Grade 0 surface provides an exacting datum for dimensional checks and layout operations. The plate conforms to DIN 876/0, making it suitable where traceable flatness and reproducible results are required. The 800 × 500 × 100 mm footprint balances reach and stiffness, allowing component placement and step measurements without sacrificing support. For workshops and inspection benches demanding a certified planar reference, this solution furnishes a reliable baseline for gauges, comparators and optical checks. Mass and material that reduce measurement uncertainty Made from dark granite, the plate offers inherent thermal stability and excellent vibration damping, characteristics that limit drift during measurement cycles. The substantial mass, approximately 156 kg, increases inertia and reduces susceptibility to external disturbance, improving repeatability for sensitive tasks. Granite’s wear resistance preserves the reference surface over prolonged use; occasional lapping restores topology without the need for frequent replacement, contributing to lower life‑cycle costs. Practical integration and handling advice The product is supplied as a control plate only, without a stand, so workshop integration should consider appropriate support and lifting arrangements. The compact block height of 100 mm permits direct use on stable benches or attachment to dedicated pedestals; mechanical levelling feet or a stout frame are recommended to maintain the designed geometry. For transport and installation, plan for mechanical handling due to the plate’s mass, and document mounting interfaces to preserve the surface against point loading and contamination. For precision inspection tasks, request the Grade 0 granite surface plate from Metav IndustryLine via Metav Werkzeuge — the Emmerich team will advise on delivery, handling and suitable support options. Technical Data Article number: M206.107 GTIN: 4054469103020 Designation: Granite surface plate, 800 × 500 × 100 mm, Grade 0 Manufacturer: Metav IndustryLine Facts Dimensions: 800 × 500 × 100 mm Weight: 156 kg ECLASS: 21170603 Tariff number: 68022300 Special features Material: dark granite Flatness: Grade 0 (DIN 876/0) Note: control plate only, without stand FAQ Is this plate suitable for calibration and inspection benches? The granite surface plate M206.107 (Metav IndustryLine) is specified to Grade 0 (DIN 876/0), making it suitable as a reference surface for bench‑top calibration and inspection tasks where high flatness is required. Does the plate come with a mounting frame or stand? Delivery is for the control plate only; the item is supplied without a stand. Appropriate support or a purpose‑built pedestal should be arranged to ensure stable, level mounting. What handling is required for installation? Due to the plate’s mass (~156 kg), mechanical lifting equipment and a stable support structure are recommended. Care should be taken to avoid point loads and contamination during positioning. How should the surface be maintained to preserve flatness? Routine cleaning with non‑abrasive cloths and avoidance of hard impacts will maintain the surface. If required, professional lapping restores the topology while preserving the Grade 0 specification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
800x500x100mm Anti-Slip Pad for Measuring Plate Frames, Fits Measuring Plate Stands - Filetta
Take advantage of a stable, low-maintenance anti-slip solution that secures measuring plates while maintaining repeatability in routine inspection tasks; compatible with 800 x 500 x 100 mm plates and supplied by Filetta. Order the anti-slip guard directly via Metav Werkzeuge or ask the consultants for specification support. Anti-slip guard for measuring plate frames by Filetta — fits 800 x 500 x 100 mm The anti-slip guard is a retrofit accessory designed to prevent lateral movement of measuring plates and to improve the reliability of measurements on a measuring table. Secure anti-slip contact for measuring plates Compatible with 800 x 500 x 100 mm plates Suitable for measuring table frames Improved measurement reliability through stable contact The primary benefit of the anti-slip guard lies in its capacity to reduce micro-movements between the measuring plate and its support. By increasing the friction interface where the plate rests, the accessory improves repeatability of successive measurements and minimises rework caused by shifting parts. For metrology teams and workshop quality control, this translates into fewer measurement rejects and a more predictable inspection workflow. The solution is particularly relevant where plates are handled frequently or where small shifts can exceed tolerance bands. Practical integration into the measuring table workflow Designed for use with plates sized 800 x 500 x 100 mm, the guard integrates with common measuring table frames without demanding complex modifications. Installation is straightforward and focuses on mechanical fixing points on the plate frame; thread and mounting details depend on the specific table design. As a result, the measure of effort to retrofit the accessory remains low while the operational gain — stable part positioning on the measuring table — is immediate. The compact form factor keeps the working surface unobstructed and maintains accessibility for standard inspection tools. Productivity gains and quality assurance advantages Adopting this anti-slip solution supports faster setup times and a reduction in incidental errors during tactile or optical measurement processes. The emphasis on stable fixturing supports consistent datum alignment and therefore contributes directly to measurement confidence. In a production environment the accessory enhances throughput by lowering the incidence of repeated measurements and by shortening inspection cycles. The supplied SKU MS131.125 identifies the exact item and facilitates procurement and traceability in inventory systems. Contact Metav Werkzeuge today for Filetta anti-slip guards compatible with 800 x 500 x 100 mm measuring plates — expert ordering assistance and specification advice available by email or phone from Emmerich. Technical data SKU: MS131.125 Article: Anti-slip guard Manufacturer: Filetta Category: Measuring table Suitable for measuring plates: 800 x 500 x 100 mm Facts Compatible plate dimension: 800 x 500 x 100 mm SKU identifier: MS131.125 Special features For measuring plate frames Anti-slip function for improved repeatability Retrofit-friendly design FAQ What plate sizes is the anti-slip guard compatible with? The anti-slip guard is designed for measuring plates with the dimension 800 x 500 x 100 mm and is supplied under SKU MS131.125 by Filetta. Will the accessory affect the measuring surface or reference points? No — the anti-slip guard secures the plate to the frame without altering the measuring surface; Filetta designed the unit to maintain existing reference geometry while reducing lateral movement. Can the anti-slip guard be retrofitted to any measuring table frame? The guard is intended for standard measuring table frames; compatibility with bespoke fixtures should be checked against the SKU MS131.125 mounting arrangement before installation. How does the anti-slip guard improve inspection throughput? By preventing plate movement, the guard increases repeatability and reduces the need for re-measurement, which shortens inspection cycles and supports steadier production yields. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
850-925mm Measuring Plate Stand With Three Supports, Two Anti‑Tilt Locks - Filetta
Benefit from a robust support frame, adjustable height options and integrated anti‑tilt fittings to secure a stable measuring base; order the Surface plate stand directly via Metav Werkzeuge or consult Metav’s specialists for configuration advice. MS131.202 Surface plate stand by Filetta — adjustable height and anti‑tilt protection The MS131.202 Surface plate stand provides a stable support frame for precision surface plates in metrology workshops, combining ergonomic height ranges with secure fixing elements for reliable, repeatable measurement setups Adjustable heights 850–925 mm for varied setups Anti‑tilt locks for secure plate fixation Levelling feet with metal caps for stable support Engineered stability for repeatable measurements A stable measuring base is essential for comparable results. The stand’s design delivers a robust support frame that minimises vibration and lateral movement during inspection work, so readings remain consistent across cycles. Built for industrial metrology, the frame suits surface plates used in quality control and assembly processes and reduces rework by keeping the reference plane steady throughout measurement sequences. Fast set‑up and secure fixation for busy shops Included with the stand are 3 support struts (Bessel style), 2 anti‑tilt locks and levelling feet fitted with metal caps, allowing rapid installation and secure mechanical retention of the surface plate. These fittings shorten preparation time and remove guesswork when locating the plate, which translates into a quicker inspection throughput and fewer interruptions on the shop floor. Flexible heights to match different workflows Three height ranges are available—850–875 mm, 870–895 mm and 900–925 mm (including surface plate)—so the support can be matched to plate thickness and operator ergonomics or integrated equipment. The adjustable heights enable comfortable working postures and straightforward alignment with peripheral tools, helping to cut operator fatigue and maintain productivity in repeated measuring tasks. Workshop‑ready design that supports quality routines The stand is specified for workshop use and fitted with practical features that withstand daily handling: levelling feet with metal caps protect floors and provide fine height adjustment, while anti‑tilt devices add a layer of safety when loading heavy plates. Supplied accessories ensure the support is ready for immediate integration into measuring benches and laboratory tables, helping to safeguard measurement quality from the start. For a dependable, height‑adaptable measuring station configured to exact workshop needs, contact Metav Werkzeuge to discuss the Filetta MS131.202 and arrange supply from Emmerich. Technical data Article number: MS131.202 Manufacturer: Filetta Category: Messtisch (measuring table) Height (including surface plate): 850–875 mm / 870–895 mm / 900–925 mm Included accessories: 3 support struts (Bessel style); 2 anti‑tilt locks; levelling feet with metal caps Facts Height ranges: 850–875 mm; 870–895 mm; 900–925 mm Special features Anti‑tilt protection Levelling feet with metal caps 3 support struts (Bessel style) FAQ Is the stand suitable for different surface plate thicknesses? Yes. The stand’s three height ranges (850–875 mm, 870–895 mm, 900–925 mm including plate) allow adaptation to different surface plate thicknesses and workshop workflows for the MS131.202 by Filetta. Which accessories are supplied with the stand? The MS131.202 is supplied with three support struts (Bessel style), two anti‑tilt locks and levelling feet with metal caps for immediate installation and secure plate fixing. Can the stand be used in a quality control laboratory? Yes. The support frame is designed for metrology applications and provides a stable measuring base suitable for quality control benches and inspection areas. How does the anti‑tilt feature improve safety? The anti‑tilt locks secure the surface plate against accidental tipping during loading or adjustment, reducing the risk of damage to the plate and ensuring a safer working environment. Is the stand compatible with standard measuring tables? The MS131.202 is categorised for measuring table use and is compatible with common workshop and laboratory arrangements where a stable, height‑adjustable surface plate support is required. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
850-925mm Measuring Table Stand With Three Supports, Tilt Locks And Metal-Capped Feet - Filetta
A robust, height‑adjustable stand that pairs stable support with practical safety features: choose the model that matches your working height and benefit from the included three bracing supports, two anti‑tilt locks and adjustable feet with metal caps for reproducible inspection results; order via Metav Werkzeuge or consult their specialists for application guidance. Measuring plate stand MS131.203 — height‑adjustable surface plate support by Filetta The Measuring plate stand MS131.203 is a floor stand designed to support a surface plate while providing two selectable working‑height ranges for inspection and metrology tasks. Height ranges 850–875 mm or 900–925 mm Three bracing supports (Bessel‑style) Two anti‑tilt safety locks Adjustable feet with metal caps Stable, adjustable support that preserves measurement accuracy A purpose‑built stand for metrology environments, the MS131.203 provides a stable support platform that reduces sources of error during inspection. The supplied height options (850–875 mm and 900–925 mm, including the measuring plate) allow ergonomic alignment with existing benches and measuring devices. By combining a rigid frame with bracing supports, the assembly helps maintain the flatness and orientation of the surface plate under typical workshop loads, which contributes directly to repeatable measurements and fewer rework cycles. Built for workshop efficiency and safe operation Safety and day‑to‑day convenience are integrated: the stand includes two anti‑tilt locks and three bracing supports to prevent accidental movement during measurements, while adjustable feet with metal caps permit stable levelling on imperfect floors. These features cut setup time and reduce the need for temporary shimming, so inspection processes run more smoothly. The mechanical simplicity of the design also minimises maintenance requirements, enabling focused metrology work without frequent adjustments. Fits inspection benches and precision workflows Designed as a support for surface plates in laboratories, workshops and quality control stations, this stand integrates easily into existing inspection layouts. The Filetta build supports conventional surface‑plate sizes and is suited to repeatable tasks such as dimensional checks, fixture set‑up and component inspection. The combination of stable construction and adjustable height translates into improved operator ergonomics and a more efficient measurement workflow, making it a pragmatic choice for production and QC environments where reliability and uptime matter. For expert advice on integrating the Filetta measuring plate stand into a workshop, contact Metav Werkzeuge in Emmerich for tailored guidance and efficient delivery Technical data Article number: MS131.203 Name: Measuring plate stand Brand: Filetta Height: 850–875 mm / 900–925 mm (including measuring plate) Accessories included: 3x bracing supports (Bessel‑style), 2x anti‑tilt locks, adjustable feet with metal caps Core technical data Height ranges: 850–875 mm; 900–925 mm Bracing supports: 3 pieces Anti‑tilt locks: 2 pieces Special features Application: support for surface plates and inspection setups Design: floor stand / tripod‑style bracing Levelling: adjustable feet with metal caps FAQ What working heights are available with this stand? The Measuring plate stand MS131.203 by Filetta offers two working‑height bands: 850–875 mm and 900–925 mm, stated values include the measuring plate. Which accessories are supplied with the unit? Delivery of the MS131.203 includes three bracing supports (Bessel‑style), two anti‑tilt locks and adjustable feet fitted with metal caps. Is the stand suitable for fixed installation in a metrology lab? Yes, the stand is designed to support surface plates for inspection and metrology tasks and is appropriate for lab or workshop installation where a stable support is required. Can the stand be levelled on uneven floors? Level adjustment is achieved via the adjustable feet with metal caps, allowing stable positioning on non‑uniform surfaces. Does the stand prevent accidental tipping during measurement? The MS131.203 is supplied with two anti‑tilt locks and three bracing supports to enhance stability and reduce the risk of accidental movement during inspections. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
850–925mm Measuring Table Frame For 2000x1000x200/250mm Plates, With Supports And Tilt Locks - Filetta
Combine robust support for large measuring plates with thoughtful workshop ergonomics: the stand offers reliable stability for 2000×1000 measuring plates, an adjustable height range for ergonomic setup and an inclusive accessory package for safe, immediate installation. Order the stand directly via Metav Werkzeuge or consult our specialists for application advice. Surface plate stand MS131.204 — rigid support for 2000×1000 mm plates, adjustable height A Filetta surface plate stand designed for 2000×1000×200/250 mm measuring plates, delivering stable support and safe handling in industrial workshops Stable support for 2000×1000 mm plates Adjustable height 850–925 mm incl. plate Includes 3 supports, 2 tipping guards, levelling feet Not suitable for base cabinet use Stable foundation for precision measurement A robust surface plate stand provides the foundation for reproducible measurement results. The MS131.204 is configured for 2000×1000×200/250 mm plates and is engineered to minimise vibration and flexing during use, which preserves the flatness of the measuring surface. By combining a rigid frame with defined support points, the stand reduces measurement scatter and shortens setup time, making it suitable for quality control benches and assembly areas where consistent readings are essential. Ergonomic height and workshop integration Two height settings are accommodated in the design, providing an adjustable height range of 850–875 mm and 900–925 mm (both ranges stated including the measuring plate). This flexibility allows the stand to suit different working postures and bench layouts while keeping the measuring surface at an optimal eye level. The controlled height options aid operator comfort and reduce handling time when transferring parts between fixtures or test stations, contributing to steady workflow and fewer handling errors. Ready-to-use accessories and safe handling Delivered with a practical accessory pack, the stand includes three support braces (Bessel), two tipping protections and levelling feet with metal caps, enabling secure positioning and rapid installation. These items minimise the need for additional purchases and support a safe working environment by preventing accidental tilt and ensuring the frame sits true on uneven floors. Note that the frame is specified as not suitable for base cabinet integration; it is intended as a free-standing support for large surface plates. Choose the Filetta surface plate stand for a dependable metrology base and contact Metav Werkzeuge in Emmerich for tailored procurement or technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: MS131.204 Name: Messplattengestell (surface plate stand) Manufacturer: Filetta Facts Compatible plate size: 2000×1000×200/250 mm Height (including plate): 850–875 mm / 900–925 mm Special features 3 support braces (Bessel) 2 tipping protections Levelling feet with metal caps Not suitable for base cabinet use FAQ What plate dimensions are compatible with this stand? The MS131.204 surface plate stand is designed for 2000×1000×200/250 mm measuring plates and supports the specified plate thicknesses for reliable bearing. Is the height adjustable to suit different operators? Yes, the stand offers two height settings—850–875 mm and 900–925 mm including the plate—so bench height and ergonomic requirements can be matched. Which accessories are supplied with the stand? Delivery includes three support braces (Bessel), two tipping protections and levelling feet with metal caps to ensure stability and safe installation. Can the stand be used with an under-shelf or base cabinet? No, the design is explicitly not suitable for base cabinet installation; it is intended as a free-standing support frame. Who manufactures this measuring table stand? The stand is produced by Filetta; the MS131.204 is specified and supplied for industrial metrology applications. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
900x600x100mm Anti-Slip Pad For Measuring Table Plate Support - Filetta
Take advantage of a secure, non-slip support that is matched to the common measuring plate size 900 x 600 x 100 mm and designed to improve repeatability on inspection tables; order the anti-slip protection directly via Metav Werkzeuge or consult Metav’s specialists for tailored advice. Anti-slip protection for measuring plate frames — compatible with 900 x 600 x 100 mm plates | Filetta The Anti-slip protection for measuring plate frames provides a stable interface for measuring plates and inspection tables, preventing unwanted movement during setup and measurement tasks while fitting standard frame designs. Secure anti-slip interface for measuring plates Designed for 900 x 600 x 100 mm plates Robust fit for measuring table frames Secure foundation for consistent measurements A stable base reduces variability in every measurement operation: the anti-slip device creates a controlled contact layer between the measuring plate and its frame, lowering the risk of lateral movement and therefore improving repeatability in routine checks. Matched specifically to the 900 x 600 x 100 mm plate geometry, the component is intended for metrology environments where consistent positioning influences traceable results. Designed for use on measuring tables and inspection stands, it supports accurate alignment without altering the plate geometry or clamping strategy. Seamless integration with frames and stands to speed setup Installation is conceived as a straightforward positioning on the plate frame so that time spent on alignment and re‑adjustment is reduced and throughput is increased. The solution is compatible with common measuring table constructions and support stands, providing a robust fit that limits micro‑shifts during probe contact or manual handling. As a practical accessory in a workshop or inspection bay, it contributes to smoother process flows and fewer repeat measurements, which in turn supports productivity and operational reliability. Durable support that protects components and workflow Built to serve as a repeatable interface, the anti-slip protection reduces abrasion and protects the plate surface during routine use and handling. The product’s role in minimising rework and stabilising setups makes it a simple, cost‑effective measure to safeguard quality gates in assembly and inspection operations. Supplied by a specialist metrology brand and distributed through Metav’s quality filter in Emmerich, the part is intended to integrate into established measurement routines and to support dependable material handling across shifts. Contact Metav Werkzeuge for guidance on integrating the Filetta anti-slip solution MS131.126 into existing measuring table setups and for supply details via +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: MS131.126 Manufacturer: Filetta Product name: Anti-slip protection Suitable for: measuring plates 900 x 600 x 100 mm Category: Measuring table Numbers / Core technical data Compatible plate dimensions: 900 x 600 x 100 mm Designs / Special features Anti-slip surface for plate-to-frame contact Intended for measuring plate frames and stands Suitable for inspection table applications FAQ Is this anti-slip protection compatible with plates other than 900 x 600 x 100 mm? The anti-slip protection is manufactured for measuring plates sized 900 x 600 x 100 mm; compatibility with other sizes is limited and may require a different accessory. How does the anti-slip protection improve measurement repeatability? By providing a non-slip interface between the plate and its frame, the accessory reduces lateral movement and micro-shifts, which helps maintain repeatability during probing and visual inspections with the Filetta anti-slip protection MS131.126. Can the anti-slip protection be used on any measuring table frame? The design is intended for typical measuring table frames and supports; it fits standard frame geometries used for inspection tables and stands, ensuring a robust fit where plate dimensions match. Does the product include mounting hardware? The Filetta anti-slip protection MS131.126 is supplied as the anti-slip component itself; any additional fastenings or frame-specific adapters are not included unless stated separately by the supplier. Who distributes this anti-slip protection in Europe? The anti-slip protection MS131.126 is distributed via Metav Werkzeuge and specialist metrology channels for reliable supply and quality assurance. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
900–975mm Measuring Plate Stand With 3 Supports, Tilt Locks And Metal‑Fitted Feet - Filetta
Stable, height-adjustable support with anti-tilt locks and three support brackets provides a dependable base for surface plates, improving repeatability in inspection tasks. The adjustable feet with metal caps permit precise levelling on uneven floors. Order via Metav Werkzeuge or consult our specialists for application guidance and supply. Surface Plate Stand MS131.201 — Filetta height-adjustable metrology frame The Surface Plate Stand MS131.201 offers a stable, height-adjustable frame for secure mounting of measuring plates in metrology, inspection and workshop environments. Height-adjustable 900–975 mm overall Anti-tilt safety devices included Three support brackets supplied Adjustable feet with metal caps Engineered for stable, repeatable measurements The stand is designed to deliver stable support for measuring plates, reducing variability in routine inspections. With two selectable overall height ranges (900–925 mm and 950–975 mm, measured including the measuring plate), the frame enables ergonomic working heights and consistent positioning of inspection artefacts. Built to hold a flat measuring surface securely, the structure combines load distribution and low centre-of-gravity to reduce micro-movements during tactile or optical checks. That predictable behaviour translates into more repeatable readings and fewer re-measurements on the shop floor. Accessories that speed up setup and increase safety Included with the frame are three support brackets (Besselsche), two anti-tilt locks and adjustable feet with metal caps, which minimise the need for additional components. The support brackets simplify the seating of the plate and aid in fine alignment; the anti-tilt locks secure the assembly during handling and maintenance, lowering the risk of accidental displacement. The adjustable feet allow precise levelling on uneven surfaces, while the metal caps protect floor finishes and provide reliable contact points. These features shorten commissioning time and reduce logistical effort during installation. Practical benefits for workshops and inspection labs This Filetta frame is suitable for quality-control benches, calibration areas and precision workshops where a stable base and correct working height are essential. The clear height ranges and solid support arrangement make the frame a pragmatic choice for teams aiming to standardise inspection procedures. The robust design supports routine metrology processes, from layout and visual checks to probing and comparative measurements, contributing to consistent part acceptance and fewer process interruptions. Integration and workplace considerations The stand is categorised for use with surface plates and bench-mounted measuring setups and is compatible with a wide range of plate sizes where the specified overall height is required. The included mounting and safety hardware reduce the need for bespoke fittings, making the frame an economical centrepiece for a measuring table or inspection station. Its straightforward architecture supports straightforward maintenance and, where necessary, rapid relocation within a production environment. For secure, height-adjustable support choose the Filetta Surface Plate Stand and contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice and reliable supply Technical Data Article number: MS131.201 Brand: Filetta Category: Measuring table / surface plate stand Height (including measuring plate): 900–925 mm / 950–975 mm Included accessories: 3 x support brackets (Besselsche), 2 x anti-tilt locks, adjustable feet with metal caps Core technical data Height range option 1: 900–925 mm Height range option 2: 950–975 mm Support brackets: 3 Anti-tilt locks: 2 Special features Height-adjustable frame for measuring plates Anti-tilt safety devices for secure handling Adjustable feet with metal caps for levelling Designed for metrology benches and inspection tables FAQ Is the height of the stand adjustable and what are the exact ranges? The Surface Plate Stand MS131.201 is supplied with two overall height ranges: 900–925 mm and 950–975 mm (both values include the measuring plate). What accessories are delivered with the frame? Delivery of the Filetta MS131.201 includes three support brackets (Besselsche), two anti-tilt locks and adjustable feet fitted with metal caps. Is this frame suitable for workshop and inspection use? Yes, the stand has been developed for measuring plates and inspection benches, making it suitable for quality-control areas and workshop metrology stations. How are levelling and stability achieved on uneven floors? The supplied adjustable feet with metal caps enable precise levelling, while the bracket layout and anti-tilt locks enhance overall stability. Can the stand be integrated immediately into an existing measuring table? The frame is configured for straightforward integration with surface plates and typical inspection setups; the included support hardware reduces the need for additional fittings. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
Ø22x160 mm Measuring Rod Three-Point Offset 40 mm - Metav IndustryLine
Take advantage of a compact, secure column accessory that combines precise positioning and easy mounting for consistent measurement routines; the combination of Ø22 × 160 mm column fit, a 40 mm reach and an M8 thread offers reliable compatibility and fast integration — order the measuring rod directly via Metav Werkzeuge or consult our specialists for application advice. Measuring rod M208.146.S – column accessory, Ø22 × 160 mm, 40 mm reach (Metav IndustryLine) The Measuring rod M208.146.S is a compact accessory designed to extend the functionality of a matching measurement column, providing a short offset arm for tight or obstructed measurement points in workshop and inspection environments. Compact column accessory Ø22 × 160 mm 40 mm offset for confined measurement zones M8 thread for secure mounting Lightweight design at 0.3 kg Stable mounting for repeatable measuring setups The extension arm is engineered as a purpose-built column accessory to integrate directly with compatible height gauges and column stands. With a Ø22 × 160 mm column fit and an M8 thread, the component ensures a secure mechanical interface that reduces play and vibration during measurement cycles. This stability translates into consistent repeatability when positioning probes or test indicators, which benefits quality control workflows by lowering the likelihood of measurement error and reducing rework. Precise access where space is limited A short projection of 40 mm is ideal when approaching features that are close to fixtures or adjacent components. The modest reach reduces cantilever effects while still granting access to recesses and edges that would otherwise be hard to reach with bulkier tooling. The configured cross arm provides a purposeful balance between accessibility and profile, so inspection tasks that require confined entry points can be executed with controlled positioning and less obstruction from the measuring rig. Lightweight construction that aids handling and alignment At approximately 0.3 kg, the rod adds minimal mass to the column assembly, keeping the overall centre of gravity close to the support axis and simplifying alignment. The reduced inertia helps during fine adjustment of the probe or indicator and makes repeated set-ups faster to achieve. Built as an accessory for the 208.146 column, the item supports efficient workflows in inspection benches and production metrology stations where quick interchangeability and reliable mechanical interface are priorities. Practical compatibility and workshop benefits Engineered for routine integration, the accessory uses standard connection geometry to match existing column systems, allowing rapid retrofitting without special adaptors. The secure thread mounting and compact geometry make it suitable for both bench-top gauges and portable column arrangements, improving flexibility across inspection tasks. As part of the Metav IndustryLine range, the rod supports a pragmatic approach to equipping workshops with modular, serviceable metrology components. For inquiries about suitability with existing gauges or to request procurement support for the Metav IndustryLine Measuring rod M208.146.S, contact Metav Werkzeuge in Emmerich on +49 2822 7131930 or by e‑mail at info@metav-werkzeuge.com — our specialists will advise on integration and delivery options. Technical data Article number: M208.146.S GTIN: 4054469104997 Category: Accessories for measuring devices Facts Weight: 0.3 kg Column diameter × length: Ø22 × 160 mm Reach / offset: 40 mm Cross arm: 60(40) Thread: M8 Customs tariff number: 90173000 UID: M208.146.S Versions / Special features Accessory for column 208.146 Story trigger: zubehör Brand: Metav IndustryLine FAQ Is this rod compatible with the 208.146 column? Yes. The measuring rod M208.146.S is designed as an accessory specifically for the 208.146 column and fits the Ø22 × 160 mm mounting. What is the nominal reach of the extension arm? The rod provides a 40 mm offset, enabling measurements in confined or partially obstructed areas. Which thread is used for mounting? Mounting is via a standard M8 thread to ensure a firm and repeatable connection to the column. How much does the accessory weigh? The component has a weight of approximately 0.3 kg, keeping added mass to a minimum for easier handling and alignment. Can this accessory be used across multiple measuring setups? Yes. The compact design and standard thread allow integration with compatible column systems, making it suitable for interchange within workshop and inspection environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Ø22x180 Column Rod with Ø18x140 Measuring Arm for Granite Table M8 Thread - Metav IndustryLine
Take advantage of the compact design, secure M8 mounting and precise alignment for repeatable measurements in confined setups. Combine robust post stiffness with a lightweight cross arm for flexible fixturing — order the measuring stem directly via Metav Werkzeuge or ask our consultants if needed. Measuring stem M208.145.S — accessory for 208.145 column with Ø22×180 mm post and Ø18×140 mm arm (Metav IndustryLine) Measuring stem M208.145.S is a compact mounting stem designed to extend the functionality of a measuring column; suitable for precision fixtures and workshop metrology where space and stable positioning are essential. Compact Ø22×180 mm column post for secure mounting Ø18×140 mm cross arm for close-range fixturing M8 thread for direct granite-plate attachment Lightweight 0.2 kg for flexible handling Stable mounting that improves measuring repeatability The accessory provides a stiff Ø22×180 mm post and a short Ø18×140 mm cross arm, yielding a stable connection between the column and the probe fixture. The reduced lever length limits deflection, which in turn reduces measurement scatter; this is particularly valuable for repeat checks and comparative measurements in workshop environments. The design supports a clear mechanical interface that maintains alignment under typical handling. Quick assembly and versatile compatibility Fitted with an M8 thread, the component enables direct attachment to preparations that accept standard M8 fixings such as granite plates or fixtures with matching receptacles. The lightweight 0.2 kg construction assists handheld positioning during setup yet provides sufficient mass to avoid unwanted vibration in normal use. Installation is straightforward and reversible, allowing the same stem to be redeployed across different setups or stored without adding bulk to the metrology bench. Suited for compact metrology workflows and robust inspection routines As an accessory for measuring columns, the stem is intended for applications that require close-range probing, datum setting and small-jig fixturing in machine shops and inspection areas. The combination of a short cross arm and a thicker post offers a balance between reach and rigidity, helping to preserve gauge repeatability under everyday workshop conditions. Sourcing this part from a specialist brand ensures consistent dimensional tolerances and dependable interchangeability with matching column systems. Choose the Metav IndustryLine measuring stem for compact, reliable fixturing — order through Metav Werkzeuge to ensure fast supply and expert advice. Technical Data Article number: M208.145.S GTIN: 4054469104973 Category: Zubehör Facts Post diameter: Ø22 mm Post length: 180 mm Cross arm diameter: Ø18 mm Cross arm length: 140 mm Thread: M8 Weight: 0.2 kg Tariff number: 90173000 Special features Accessory for 208.145 measuring column Designed for secure mounting and minimal deflection Compact form factor for confined setups Manufacturer: Metav IndustryLine FAQ What does this stem fit? The stem is intended for use with the 208.145 measuring column and mates to fixtures that accept an M8 threaded attachment. Is the cross arm suitable for probe mounting? Yes, the Ø18×140 mm cross arm provides a stable short-reach mounting point suitable for probe holders and small fixtures. How much does the accessory weigh? The measuring stem weighs 0.2 kg, which supports easy handling and reconfiguration of the measuring setup. Can the stem be mounted to a granite plate? The component features an M8 thread, allowing direct attachment to granite plates or fixtures with compatible M8 receptacles. Which brand produces this accessory? This accessory is distributed under the Metav IndustryLine brand and designed for consistent compatibility with related column systems. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Ø60 mm Messtisch Stand With Ø22x180 mm Column, Fine Adjustment, Base 149x90x30 mm - Microtech Metrology
Take advantage of a compact, workshop-ready solution that combines a fine-adjustment spindle with a Ø60 mm measuring table and a rigid Ø22 × 180 mm column for reproducible indicator positioning — order directly via Metav Werkzeuge or request advice from our consultants. Stand — Dial gauge stand with fine adjustment and Ø60 mm table (Microtech Metrology) The Stand is a dial gauge stand designed for stable, repeatable measurements in workshops and inspection benches, combining a compact base with micrometre-style positioning for precise indicator alignment. Fine-adjustment mechanism for micrometre positioning Large Ø60 mm measuring table for stable mounting Rigid column Ø22 × 180 mm for consistent support Compact base 149 × 90 × 30 mm for bench stability Precision control for reliable measurement results The combination of a fine adjustment mechanism and a robust support geometry enables controlled, small-step positioning of indicators, reducing setup variability. A micrometre-like adjustment removes abrupt movements and helps achieve repeatable contact force when taking readings. This level of control suits routine inspection tasks where small deviations matter and contributes directly to reduced rework and faster quality checks. The dial gauge stand concept supports common workshop indicators and makes precise comparative measurements straightforward. Stable construction for repeatable setups A substantial Ø60 mm measuring table and a Ø22 × 180 mm column form the mechanical backbone for consistent mounting and resistance to lateral play. The 149 × 90 × 30 mm base sits low on the bench to minimise rocking, while the vertical support maintains alignment during repeated measurements. These structural choices translate into measurable benefits: fewer discarded parts, less time spent on repositioning, and improved data quality in small-series production and toolroom tasks. The design balances rigidity and compact footprint for everyday metrology needs. Workflow integration and workshop benefits Engineered for practical bench use, the device accepts standard indicator fittings and fits easily into inspection stations or alongside machine tools. The fine adjustment feature eases the alignment of measuring probes to narrow grooves or small bores, while the compact footprint keeps valuable bench space free. Supplied by Microtech Metrology, the unit is tailored to users who prioritise dependable setup and swift changeovers; it supports routine checks, go/no‑go comparisons and setup verification with minimal additional tooling. Clear mechanical design reduces user training time and simplifies daily operation. For tailored purchasing or technical clarification, contact Metav Werkzeuge in Emmerich — Metav Werkzeuge provides product advice and order handling via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 161002020 GTIN: 4061905456619 Manufacturer: Microtech Metrology eClass: 21170604 Core specifications Base dimensions: 149 × 90 × 30 mm Measuring table: Ø60 mm Column: Ø22 × 180 mm Mounting / receptacle: 8 Fine adjustment: yes Special features Fine-adjustment spindle for precise positioning Designed for dial gauges / dial indicators Compact footprint for bench integration Rigid column for repeatable setups FAQ What indicator types fit the stand? The stand accepts standard dial gauges and dial indicators; the mounting receptacle is listed as 8 and accommodates common indicator stems for secure fastening. Is this product supplied ready for use straight away? The Microtech Metrology dial gauge stand is delivered as a ready-to-install fixture and includes the mechanical fine-adjustment feature for immediate integration into inspection stations. Can the stand be used for comparative measurements on a production bench? Yes, the combination of a Ø60 mm measuring table and a rigid Ø22 × 180 mm column makes the stand suitable for repeatable comparative and setup measurements in small-series production. Does the stand require any special mounting or clamping? No specialised clamping is required; the compact base and standard mounting interface enable secure bench placement and straightforward attachment of dial indicators. Which benefits does the fine adjustment provide in daily use? The fine adjustment allows controlled micro-movements, improving alignment accuracy and reducing the risk of overshoot when positioning probes for tight features. Microtech Metrology: Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Precision and stability for reliable measurement results
A measurement table provides the essential reference surface for precise dimensional inspection in machine shops, metalworking and quality assurance. Selected and configured correctly, a measurement table ensures consistent flatness, repeatability and a stable basis for comparative measurement tasks.
How the system works and where it’s indispensable
The primary role of a measurement table is to act as a flat, stable datum for handheld gauges and fixed measuring stands. Typical constructions include granite plates, cast-iron plates, and versions prepared for integration with a height gauge or a dedicated stand. In inspection rooms and workshops a well-chosen metrology table reduces measurement scatter by isolating the part from bench vibration and by providing a reliably machined reference plane for both manual and semi-automatic checks.
Tangible benefits that improve daily production
- Increased measurement repeatability by providing a stable reference surface, reducing rework and scrap.
- Faster setup and alignment when used with a height gauge or measuring stand, cutting throughput time for routine checks.
- Robustness and wear resistance from materials such as granite plates or cast-iron plates, extending service intervals.
- Compatibility with common inspection tools, making the inspection table a versatile centrepiece for quality workflows.
Why Metav is the practical choice for workshops and industry
Metav combines industry expertise with wide availability, making precision accessible without compromising quality. From its Emmerich location Metav acts as a quality filter for the European market, supporting over 48,000 customers and offering more than 250,000 products for measurement and workshop equipment. That breadth ensures the right measurement table solution is available alongside complementary metrology accessories, delivered with straightforward order handling and dependable stock management.
Quick summary
A properly specified measurement table — whether a granite plate, a cast-iron plate or a version adapted for a height gauge — is a foundational investment for accurate, efficient inspection. Metav offers the range and expertise to match the right table to the application.
FAQ
Which material is best for my measurement table?
Choice of material depends on use: granite plates are favoured for thermal stability and wear resistance, while cast-iron plates provide cost-effective rigidity. Select a measurement table material that suits your workshop environment and inspection frequency.
Can a measurement table be used with a height gauge?
Yes. Most measurement table designs are compatible with a height gauge or measuring stand; look for tables prepared with mounting or clamping options to secure the gauge and maintain repeatable set-ups.
How should I maintain a measurement table to preserve flatness?
Regular cleaning, avoidance of point impacts and controlled storage conditions help preserve the reference surface. For critical processes, schedule inspection and calibration of the inspection table according to internal quality procedures or industry standards.
What makes Metav a reliable supplier for metrology tables?
Metav combines decades of sector knowledge with a comprehensive product range from Emmerich, offering consistent quality control, broad selection and supply reliability for the workshop or production floor.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com