End gauges for precise length calibration
End gauges provide exact reference lengths for calibrating measurement instruments and ensuring consistent dimensional accuracy in metalworking and inspection processes. Used in production and laboratory settings, these end gauges—made from steel, ceramic or carbide—allow technicians to compensate for wear and thermal effects and maintain measurement traceability, especially when employed alongside parallel end gauges, cylinder gauges and calibration masters. Classes 0, 1 and 2 define practical tolerance levels for workshop, inspection-room and production use respectively, delivering the repeatable precision required for machining and quality control.
50 mm Gauge Block Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Benefit from a Grade 0 reference length, hardened special steel construction and compact handling weight for reliable workshop verification; order the single gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Single gauge block 50 mm (DIN EN ISO 3650) — Grade 0, hardened special steel The Single gauge block 50 mm serves as a high-precision length standard for calibration, comparator setups and laboratory verification in industrial and toolroom metrology. DIN EN ISO 3650, Grade 0 accuracy Hardened special steel construction Precise 50 mm reference dimension Compact weight 0.122 kg for easy handling Stable reference that reduces measurement uncertainty A hardened, single gauge block delivers a reproducible reference for length checks and master comparisons. Made from hardened special steel, the block resists wear and thermal influence better than untreated metals, ensuring the 50 mm nominal remains constant under routine use. As a Grade 0 reference under DIN EN ISO 3650, the standard offers a fine tolerance band suitable for calibration benches and quality control tasks where traceable, repeatable lengths are required. The compact mass and short form factor make transfer measurements and stack combinations straightforward while limiting added uncertainty from handling. Robust design tailored for repeatable workshop use The geometry and cross-section conform to industry expectations for end measures: for nominal sizes above 10 mm the block follows the larger section profile to maintain stiffness and contact stability. The specified cross-section 35 x 9 mm for larger nominal sizes provides a secure contact area that reduces tilt during stacking and comparison. The resilient surface finish and hardened substrate lower the rate of surface wear, extending service life and reducing the frequency of recalibration. For everyday metrology in production and inspection, this balance of stiffness and compactness supports efficient throughput and durable performance. Ease of integration into existing calibration chains The block is supplied with clear identifiers (SKU and GTIN) for inventory and traceability workflows and suits use as a stand-alone reference or as part of a stacked master set. Its modest weight (0.122 kg) and conventional form factor mean rapid alignment in comparators, gauge blocks sets and optical measuring devices. Where masters need to be combined, matching faces and consistent tolerances simplify setting up gauge stacks without complex fixture changes. The stable mechanical properties of the material make the block suitable for repeat measurement tasks in both workshop and laboratory environments. Contact Metav Werkzeuge today to request this Grade 0 50 mm reference standard and ensure a reliable length baseline for production or calibration workflows – Metav Werkzeuge provides expert advice from Emmerich for European customers Technical data Article number: M319.500.0 GTIN: 4054469132228 Nominal length: 50 mm Standard: DIN EN ISO 3650 Grade: 0 Facts Weight: 0.122 kg Cross-section (nominal > 10 mm): 35 x 9 mm Tariff code: 90173000 Special features Material: hardened special steel Category: End gauges Durable contact faces for repeated stacking Compact format for bench and laboratory use FAQ What tolerance class does this gauge block meet? The single gauge block conforms to Grade 0 tolerances according to DIN EN ISO 3650, offering a high-precision reference suitable for calibration and inspection. Which material is used and why is it important? The block is manufactured from hardened special steel, chosen to reduce wear and thermal sensitivity so the 50 mm reference remains stable under typical workshop conditions. How is the product identified for inventory and traceability? Identification includes the SKU M319.500.0 and GTIN 4054469132228, allowing straightforward integration into inventory systems and calibration records. Can this block be used in stacked measurement setups? Yes; the design and contact-face finish are intended for reliable stacking with other gauge blocks and for use in comparator arrangements. Is the block suitable for laboratory and workshop use? The combination of DIN EN ISO 3650 Grade 0 and a hardened material makes it appropriate for both laboratory verification and robust workshop applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50 mm Gauge Block, Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of the combination of Grade 1 accuracy, a hardened special‑steel construction and compact 50 mm nominal length for a dependable workshop reference — order the gauge directly via Metav Werkzeuge or ask our consultants for guidance. End measure 50 mm (DIN EN ISO 3650), Grade 1 — Metav IndustryLine The End measure 50 mm is a hardened special‑steel length standard manufactured to DIN EN ISO 3650 for precise workshop and inspection tasks. Grade 1 accuracy to DIN EN ISO 3650 Hardened special steel for long service life Compact 50 mm reference length Dependable reference for routine quality control This compact length standard delivers a stable reference point for daily calibration and comparative checks. Built to DIN EN ISO 3650 and specified as Grade 1, the instrument offers a level of dimensional certainty that reduces rework and speeds up in‑line inspections. The hardened construction provides resistance to wear, which keeps the reference dimension stable over repeated handling. As a result, process control benefits from fewer deviations and more consistent production tolerances. Robust design that withstands workshop use Manufactured from hardened special steel, the gauge resists knocks and surface wear that would otherwise degrade accuracy. The cross‑section design (up to 10 mm: 30x9 mm; above 10.1 mm: 35x9 mm) balances rigidity with a compact form, making the part easy to position while maintaining stiffness under normal measuring procedures. This durability translates into lower lifetime cost because the reference remains serviceable for longer periods, preserving measurement reliability in demanding environments. Ideal for fine mechanical and micro measurements Classified in the micro range (10–100 mm), this 50 mm reference is optimised for precision tasks where short measuring legs and minimal torsion are essential. Its compact size and stable geometry make it particularly suitable for fine mechanical work, small assemblies and precision toolshops that require a trusted length standard for comparative gauging and setup. The lightweight build also simplifies handling and positioning during multi‑point checks. For supply and specialist advice on the Metav IndustryLine 50 mm end measure, contact Metav Werkzeuge in Emmerich by phone or email for a tailored recommendation Technical data SKU: M319.500.1 GTIN: 4054469132235 Nominal length: 50 mm Weight: 0.122 kg Tariff number: 90173000 Facts Cross-section: up to 10 mm → 30 x 9 mm; above 10.1 mm → 35 x 9 mm Material: hardened special steel Grade: 1 Standard: DIN EN ISO 3650 Special features Category: End measures Manufacturer: Metav IndustryLine Intended use: precision reference for workshop and inspection Compact format for micro measurement range FAQ What level of accuracy does this gauge provide? The Metav IndustryLine 50 mm end measure is specified as Grade 1 under DIN EN ISO 3650, providing a stable workshop reference suitable for routine dimensional control. Is the 50 mm end measure suitable for precision toolmaking? Yes, the 50 mm reference is classified in the micro range (10–100 mm) and is well suited to fine mechanical work, small assemblies and precision toolmaking tasks. What material is used for the gauge and why does it matter? The gauge is manufactured from hardened special steel; this material choice increases wear resistance and maintains dimensional stability during repeated use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
500 mm End Gauge Holder 400–500 mm Clamping Range, Very Sturdy Construction - Metav IndustryLine
Benefit from a very stable construction and an extendable 400–500 mm clamping range that secures gauge blocks for repeatable calibration results; order directly via Metav Werkzeuge or consult our advisers for integration into existing metrology routines. Gauge Block Holder 500 mm (M317.114) — extendable 400–500 mm clamping range, very stable construction (Metav IndustryLine) The Gauge Block Holder 500 mm secures end gauges and similar standards for precise measurement and calibration tasks in industrial metrology Very stable construction Clamping range 400–500 mm (extendable) Compact cross-section 30.5 x 2.5 mm Low weight approx 1 kg Reliable support for precise calibration and repeatable results The holder’s very stable construction delivers a secure reference for gauge blocks, which reduces setup variation and improves repeatability in routine calibrations. The combination of a rigid profile and a precisely defined clamping area ensures that end measures remain immobile during inspection, lowering measurement uncertainty. For workshops and calibration laboratories where consistent results are essential, this device provides a straightforward way to translate gauge-block standards into reproducible measurement outcomes. Flexible clamping and easy handling for varied metrology tasks With a clamping range of 400–500 mm that can be extended, the holder adapts to a broad span of gauge block stacks and lengths, reducing the need for multiple fixtures. The slim 30.5 x 2.5 mm cross-section increases profile stiffness relative to weight, so the holder remains both stable and easy to position on benches or in test rigs. At approximately 1 kg, the device balances portability with the mechanical robustness required for industrial use, enabling simple handling without compromising support during fine measurement work. Integrates with calibration workflows to safeguard production quality Designed for use alongside standard end gauges, the holder supports efficient calibration sequences and consistent traceability across measurement chains. By delivering stable fixation and predictable geometry, the device helps to shorten setup times and reduces rework caused by inconsistent fixturing. In quality control and toolroom environments, this translates into fewer process interruptions and more reliable documentation of reference measurements, supporting overall productivity and audit-readiness. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine gauge block holder can be integrated into calibration workflows — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M317.114 GTIN: 4054469127439 ECLASS: 21170108 TARIC/HS code: 90173000 Manufacturer: Metav IndustryLine Facts Clamping range: 400–500 mm (extendable) Nominal length: 500 mm Cross-section: 30.5 x 2.5 mm Weight: 1 kg Special features Very stable execution Designed for gauge block/end measure fixation Category: Endmasse SKU: M317.114 FAQ How does the holder secure gauge blocks for calibration? The gauge block holder (Metav IndustryLine M317.114) uses a rigid profile and controlled clamping range to keep end measures immobile, enabling stable reference positioning for accurate calibration. Can the clamping range be adapted for different gauge block stacks? Yes, the clamping range of 400–500 mm is extendable, allowing the holder to accommodate varying stack heights without the need for multiple fixtures. Is the device suitable for use in a busy workshop environment? The holder’s very stable construction and compact cross-section (30.5 x 2.5 mm) provide the stiffness required for workshop use while the modest weight of about 1 kg simplifies handling and repositioning. Which product identifier should be quoted when ordering or enquiring? Please refer to M317.114 (GTIN 4054469127439) and the Metav IndustryLine designation when placing orders or requesting further details. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
500 mm Gauge Block Set Grade 0 DIN EN ISO 3650 Hardened Special Steel, 35x9mm - Metav IndustryLine
The combination of DIN EN ISO 3650 conformity, Grade 0 accuracy and a hardened special steel construction ensures reliable, repeatable length references for medium-range metrology tasks; use this robust 500 mm end gauge to stabilise setup and measurement workflows. Order or request advice directly via Metav Werkzeuge for prompt supply and technical consultation. End gauge 500 mm (DIN EN ISO 3650) — Grade 0, hardened special steel (Metav IndustryLine) A End gauge 500 mm serving as a traceable reference for dimensional checks and setup tasks in machine shops and quality departments. 500 mm nominal length, DIN EN ISO 3650 Grade 0 accuracy for high-precision checks Hardened special steel construction Compact cross-section 35 x 9 mm, robust design Consistent accuracy backed by recognised standards The device is manufactured to DIN EN ISO 3650 and specified at Grade 0, providing a well-defined reference within the family of end measures. This standard designation communicates tight tolerances and consistent production control, which makes the gauge a trustworthy baseline when checking calipers, setting fixtures or verifying machine output. For procurement and inspection planners the practical effect is predictable performance: the reference length is produced and controlled to the standard named on the product, reducing ambiguity during audits and incoming inspections. The precise designation also simplifies documentation of measuring processes and conformity demonstrations. Medium-range reference that balances reach and rigidity Classified for the medium measurement band, this 500 mm reference fills the gap between bench-length and long-bar standards. The size offers the best compromise between measuring reach and profile stiffness, helping to avoid sag or flex that can complicate repeatable readings. In workshops that handle components such as larger housings, fixtures or mould inserts, the gauge provides a stable datum without the handling complications of much longer bars. The compact cross-section and overall geometry are designed to hold alignment while remaining convenient to position, enabling efficient, single-operator checks and saving time during setup and verification routines. Durable build for long-term dimensional stability Constructed from hardened special steel, the end gauge resists wear on its reference faces and maintains form under regular use. The 35 x 9 mm cross-section contributes to a robust contact area while keeping the overall mass manageable for routine handling; the listed mass of 1.8 kg balances solidity with ergonomics. Those aspects together reduce the frequency of corrective maintenance and preserve the datum over many inspection cycles. For quality managers, this means fewer replacements and more reliable control of tolerance chains where the reference length is part of the measurement traceability. Integration into workshop and inspection workflows As a Grade 0 end measure the instrument is suitable for use as a workshop reference for setting and checking tools, for comparative checks in quality control, and for establishing master lengths in inspection routines. It pairs effectively with calipers, height gauges and fixture setups that require a stable, standardised length. The product’s GTIN (4054469132501) and SKU support easy identification in procurement systems and stock management, while the clear standard marking simplifies work instructions and inspection plans. For specific process integrations or traceability requirements, Metav Werkzeuge’s technical team can advise on documentation and handling best practices. Contact Metav Werkzeuge for ordering or technical consultation on the Metav IndustryLine end gauge 500 mm and ensure the right reference solution is supplied to your workshop and inspection routines Technical Data Article number: M320.500.0 GTIN: 4054469132501 SKU: M320.500.0 Standard: DIN EN ISO 3650 Facts Nominal length: 500 mm Cross-section: 35 x 9 mm Mass: 1.8 kg Tariff number: 90173000 Special features Material: hardened special steel Grade: 0 according to DIN EN ISO 3650 Category: End measures / End gauge FAQ What tolerance class does this end gauge follow? The end gauge conforms to DIN EN ISO 3650 and is specified as Grade 0, which denotes the tight tolerance class for end measures in that standard. Is the 500 mm end gauge suitable for machine-shop setup work? Yes, the 500 mm Metav IndustryLine end gauge is intended for medium-range workshop tasks such as setting fixtures, comparative checks and measurement verification. What material is used and how does that affect wear? The product is made from hardened special steel, which reduces wear on the reference faces and helps preserve dimensional stability over many inspection cycles. How should the end gauge be stored to maintain accuracy? Store the end gauge in a clean, dry place away from heavy vibration or direct impacts; retain original packaging or a cushioned storage location to protect the reference faces. Can the Metav IndustryLine end gauge be identified in procurement systems? Yes, the item is listed with GTIN 4054469132501 and SKU M320.500.0, facilitating stock control and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
500 mm Gauge Block, Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Benefit from a reliable workshop reference that combines DIN EN ISO 3650 conformity, a hardened special steel construction and a stable 35×9 mm profile for reproducible length checks; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. End measure 500 mm — End gauge, Grade 1 (Metav IndustryLine) The End measure 500 mm is a precision length standard for calibration and verification in industrial metrology, manufactured to DIN EN ISO 3650 and specified as Grade 1 for use as a stable workshop reference. DIN EN ISO 3650 compliant, Grade 1 Hardened special steel construction 500 mm nominal length, 35×9 mm cross-section Robust weight 1.8 kg for stable placement Precision and conformity that aids reliable calibration The instrument is produced to the DIN EN ISO 3650 specification and graded as Grade 1, which positions it as a high-quality length standard for routine verification and dimensional checks. Manufactured from hardened special steel, the standard provides mechanical stability and resistance to wear, ensuring long-term repeatability. As a fixed-length reference of 500 mm, the component serves as a stable baseline for setting gauges, verifying machine travel or checking jig alignments. The combination of standard conformity and processed steel reduces measurement uncertainty during frequent workshop use. Design features that support accurate handling and measurement A compact rectangular cross-section of 35×9 mm and a mass of 1.8 kg give the standard inherent stiffness and a low centre of gravity, which helps to avoid rocking during placement. The robust profile is advantageous when the reference needs to be positioned on machine beds or between v‑blocks: the weight improves contact stability while the hardened surface minimises wear on measuring faces. Where traceable comparisons are required, this length standard provides a durable and easy‑to‑position reference that supports consistent, reproducible results across routine inspection tasks. Practical integration into workshop processes The construction and nominal size make the device suitable as a permanent bench reference or as a portable verification standard for on‑site checks of calipers, micrometers and machine travel. The format and material selection favour stable thermal behaviour for short transfer times between environments, and the clear nominal dimension reduces setup time. Delivery includes the indicated conformity to DIN EN ISO 3650, allowing procurement and quality teams to document the use of a recognised industry standard in internal measurement procedures and traceability records. For a robust, standards‑based length reference from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to discuss suitability for specific inspection routines or to arrange immediate dispatch; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M320.500.1 GTIN: 4054469132518 Category: End measures Facts Nominal length: 500 mm Cross-section: 35×9 mm Weight: 1.8 kg Tariff number: 90173000 Special features Material: Special steel, hardened Standard: DIN EN ISO 3650 Grade: 1 FAQ What level of conformity does this length standard have? The length standard is manufactured to DIN EN ISO 3650 and supplied as Grade 1, making it suitable for workshop and inspection tasks that require a stable, recognised reference. Can this end gauge be used to verify calipers and micrometers? Yes, the 500 mm end measure functions as a fixed reference for verifying travel lengths and calibration checks on calipers, micrometers and machine axes. What material is used and how does it affect durability? The device is made from hardened special steel, which provides surface hardness and wear resistance for prolonged use as a comparative reference in routine measurement tasks. Is the 35×9 mm cross-section relevant for stability? The 35×9 mm profile and the 1.8 kg mass contribute to mechanical stiffness and placement stability, reducing the risk of rocking during measurements. How should the length standard be stored to maintain accuracy? Store the standard clean and dry on a flat surface or in a protective fixture; avoid prolonged exposure to aggressive media and handle with care to preserve the measuring faces. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
500-800mm End Gauge Holder Very Sturdy Design - Metav IndustryLine
Take advantage of the very sturdy construction, the 500–800 mm clamping range and the low mass for reliable handling; order directly via Metav Werkzeuge or consult the technical team for application advice. Metav IndustryLine End gauge holder M317.208 – 500–800 mm clamping range, very sturdy design A robust end gauge holder 500–800 mm designed to secure end measures for precise measurement and calibration in workshop and inspection settings. Robust construction for industrial use Clamping range 500–800 mm Low weight 0.4 kg for easy handling Cross-section 30×5 mm (≤300 mm) / 30×6.7 mm (>300 mm) Precision and stability for calibration tasks The holder’s very sturdy construction has been engineered to provide repeatable positioning of reference gauges, reducing variability during calibration and comparative measurements. With a clamping range 500–800 mm, the device accommodates extended end measures and large gauge assemblies, supporting traceable checks and alignment tasks. The stable profile minimises flex under load so that a known reference stays fixed during measurement, which improves overall process reliability and shortens inspection cycles. Practical design that supports workshop routines A compact mass of 0.4 kg combined with a stiff profile makes the unit straightforward to handle on test benches and portable set-ups. The stepped cross-section 30×5 mm / 30×6.7 mm balances low weight with necessary rigidity: the slimmer profile reduces bulk where possible, while the thicker section increases resistance to bending where length demands it. The result is a holder that is easy to position yet resists deformation, helping to preserve gauge geometry and ensuring consistent contact during gauge-to-gauge comparisons. Integration, documentation and supplier assurance Supplied by Metav IndustryLine, this holder is intended for workshop calibration, laboratory checks and fixture set-ups where secure retention of end measures is essential. The item is traceable via its SKU and GTIN and suited to standard calibration workflows; documentation and specification details are available on request to support quality records. For purchasers seeking dependable supply, the brand benefits from Metav’s European quality filter and centralised logistics, which help ensure continuity of supply and consistent product quality. Choose the Metav IndustryLine end gauge holder for robust, repeatable calibration work and contact Metav Werkzeuge in Emmerich for specification support and ordering assistance Technical data Article number: M317.208 GTIN: 4054469127545 Tariff number: 90173000 Label: End gauge holder 500 - 800 mm clamping range 500 - 800 mm Manufacturer: Metav IndustryLine Facts Clamping range: 500–800 mm Cross-section: 30×5 mm (≤300 mm) / 30×6.7 mm (>300 mm) Weight: 0.4 kg Special features Very sturdy construction Intended for end measures and calibration tasks Category: Endmasse SKU: M317.208 FAQ What is the usable clamping range of this holder? The clamping range is 500–800 mm, making the Metav IndustryLine end gauge holder M317.208 suitable for larger end measures and extended gauge assemblies. Is the holder suitable for calibration tasks in a metrology lab? Yes; the holder is designed to secure end measures during precise measurement and calibration, offering stable support for repeatable checks. How does the cross-section affect performance? The stepped cross-section (30×5 mm up to 300 mm and 30×6.7 mm above) increases stiffness where needed while keeping overall weight low, improving resistance to bending over longer spans. Can the holder be easily moved between benches or to site? With a weight of 0.4 kg, the unit is light enough for routine handling and transport between workstations while still providing a rigid reference when clamped. Which applications are typical for this holder? Typical uses include gauge-to-gauge comparisons, calibration set-ups, fixture support and workshop inspection tasks where secure clamping of end measures is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Rely on the combination of ceramic construction, Grade 1 (DIN 861/1) accuracy and compact handling for a stable reference standard; order directly via Metav Werkzeuge or consult our specialists for integration into existing inspection routines. Ceramic gauge block 6 mm, Grade 1 (DIN 861/1) — Metav IndustryLine The Ceramic gauge block 6 mm, Grade 1 (DIN 861/1) is a compact reference standard designed for high‑precision dimensional checks in calibration, toolmaking and inspection applications. Ceramic gauge block, high dimensional stability Grade 1 accuracy according to DIN 861/1 Nominal size 6 mm, precision-ground Compact, low weight 0.01 kg Reference stability for dependable measurements The compact ceramic reference offers a consistent baseline for length calibration and comparative inspection tasks. Constructed from ceramic, the block delivers excellent dimensional stability across typical workshop temperature fluctuations, reducing drift compared with many metal standards. Its classification as Grade 1 (DIN 861/1) signals compliance with established industrial tolerances and makes the part suitable as a laboratory reference or a shop‑floor standard for routine quality checks. The small form factor simplifies handling while preserving a reliable contact surface for gauge and probe comparisons. Material benefits and durability engineered for regular use Ceramic as a material brings notable advantages: low thermal expansion, high wear resistance and intrinsic corrosion immunity, which together extend service intervals and reduce the need for frequent reconditioning. The polished measuring faces are precision‑ground to minimise surface irregularities and to ensure reproducible contact conditions. At a nominal size of 6 mm and a weight of 0.01 kg, the block is straightforward to position and protect in a small case or drawer, while still providing the stability required for repeatable reference measurements in demanding production environments. Practical integration into inspection workflows This reference block suits calibration benches, toolrooms and production sampling where a compact, traceable standard is required. Its compact dimensions make it ideal for paired checks against micrometres, slip gauges and optical comparators, supporting fast verification cycles and reducing machine downtime. Because the block is free from active coatings, it maintains consistent contact behaviour throughout routine use and is compatible with common laboratory cleaning procedures. The combination of material and grade provides a pragmatic balance between long‑term reliability and ease of handling for everyday quality assurance. For traceable reference standards select the Metav IndustryLine ceramic gauge block and contact Metav Werkzeuge for specialist advice and direct supply from Emmerich — eMail: info@metav-werkzeuge.com · Tel: +49 2822 7131930 Technical data Article number: M324.006 GTIN: 4054469143002 Tariff number: 90173000 Weight: 0.01 kg Numbers / Core technical data Nominal size: 6 mm Grade: 1 Weight: 0.01 kg Special features Material: Ceramic Category: Gauge blocks / End measures Precision: DIN 861/1 FAQ What accuracy class does this gauge block comply with? The ceramic gauge block meets Grade 1 (DIN 861/1) tolerances as specified for the Metav IndustryLine 6 mm reference, making it suitable for standardised inspection routines. Is the material suitable for use in humid or corrosive environments? The ceramic construction of the 6 mm gauge block provides intrinsic corrosion resistance, so the Metav IndustryLine reference tolerates humid workshop conditions better than many metallic standards. Can the block be used as a calibration reference for micrometres and comparators? Yes; the precision‑ground faces of the Metav IndustryLine ceramic gauge block are suitable as a compact reference for micrometres, comparators and comparative measurement tasks. How should the gauge block be stored to retain its accuracy? Store the 6 mm ceramic gauge block in a clean, dry environment and protect the measuring faces from dust and impact to preserve the polished contact surfaces and long‑term accuracy. Does the block require special cleaning or maintenance? Routine cleaning with a soft, lint‑free cloth and a mild solvent is appropriate; aggressive abrasives or impact should be avoided to maintain the measuring faces of the Metav IndustryLine block. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6 mm Gauge Block Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Benefit from the combination of DIN EN ISO 3650 Grade 1 accuracy, hardened special steel construction and the compact 6 mm nominal length for reproducible reference measurements; order the gauge block directly from Metav Werkzeuge or consult Metav's specialists for application advice. Gauge block 6 mm — DIN EN ISO 3650 Grade 1, hardened special steel (Metav IndustryLine) A gauge block 6 mm intended as a short, high‑precision length standard for inspection benches, calibration jigs and workshop reference sets. DIN EN ISO 3650, Grade 1 accuracy Hardened special steel construction Exact nominal length 6 mm Consistent accuracy for inspection and control The block is manufactured to DIN EN ISO 3650 and rated Grade 1, offering a defined tolerance band suitable for workshop metrology and component inspection. This class ensures repeatable comparisons and tolerances that align with industry practice, making the item a dependable short reference on inspection benches. The nominal length and class together translate into a measurable benefit: reduced uncertainty during comparative measurements and faster decision making in quality control. Robust material and compact handling Made from hardened special steel, the block resists surface wear and preserves parallelism over repeated use. The compact geometry and light mass ease handling while maintaining stability during contact measurements; the specified 30 x 9 mm cross‑section for sizes up to 10 mm gives a practical balance between gripability and thermal inertia. The material choice minimises maintenance and extends lifetime, which is particularly relevant where frequent checks are required. Integration into routine metrology workflows This short standard integrates easily into dimensional control routines and reference sets. Its small form factor simplifies storage in block sets or protective trays, while the clear nominal 6 mm marking reduces setup time during calibration sequences. The construction supports rapid, rational workflows: fewer instrument adjustments, faster throughput and a lower risk of handling error—advantages that directly improve measurement efficiency on the shop floor. For traceable, workshop‑grade length standards from the Metav IndustryLine range, contact Metav Werkzeuge to discuss supply and logistics from Emmerich and secure the appropriate reference blocks for quality assurance programmes. Technical Data Article number: M319.060.1 GTIN: 4054469131412 Norm: DIN EN ISO 3650 Grade: 1 Material: Special steel, hardened Nominal length: 6 mm Cross-section (≤10 mm): 30 x 9 mm Weight: 0.009 kg Tariff number: 90173000 Facts Nominal length: 6 mm Cross-section: 30 x 9 mm Weight: 0.009 kg GTIN: 4054469131412 Tariff number: 90173000 Special features Compliance: DIN EN ISO 3650, Grade 1 Material: Hardened special steel Cross-section specification for sizes ≤10 mm Category: Gauge blocks (end measures) Brand: Metav IndustryLine FAQ What tolerance class does this block comply with? The block complies with DIN EN ISO 3650 and is supplied in Grade 1, providing workshop‑level accuracy suitable for many inspection and comparative measurement tasks. Is the nominal size clearly specified and stable? Yes, the nominal 6 mm dimension is the defined reference length and is provided in a hardened special steel body with a 30 x 9 mm cross‑section for sizes up to 10 mm, designed for stability under normal handling. Can this block be used in a reference set for routine calibration? The Metav IndustryLine 6 mm block is intended for inclusion in workshop reference sets and inspection benches where Grade 1 accuracy meets the required tolerance band for standard comparisons. How does the material affect lifetime and wear resistance? The hardened special steel composition improves surface durability and preserves parallelism, reducing the frequency of reconditioning compared with softer materials. What information identifies the product for procurement? The product is listed under SKU M319.060.1 with GTIN 4054469131412 and is classified as a gauge block (end measure) to DIN EN ISO 3650, Grade 1. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6 mm Gauge Block, Grade 0 DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of the combination of standard‑compliant accuracy, robust hardened special steel construction and compact nominal size to secure reliable reference measurements in the workshop; suitable where repeatable benchmarks are needed for inspection or setup. Order the single gauge block directly via Metav Werkzeuge or ask our consultants if needed. Single gauge block 6 mm — Grade 0, DIN EN ISO 3650 (Metav IndustryLine) A single 6 mm gauge block designed as a precision reference for calibration, inspection and stack building in dimensional metrology. DIN EN ISO 3650 Grade 0 precision Hardened special steel for durability Nominal size 6 mm for reference stacks GTIN 4054469131405 and SKU M319.060.0 Reference accuracy for reliable inspection Manufactured to DIN EN ISO 3650 and specified as Grade 0, this gauge block provides a high level of reference precision for comparative measurements and stack formation. The nominal 6 mm size makes it suitable as a base element in reference sets or for short‑span calibration tasks where thermal stability and dimensional fidelity matter. The conformity to an established standard supports traceable workflows and easier documentation in quality processes, reducing uncertainty during routine inspections. Durable construction that preserves geometry The body is made from special steel, hardened, which resists wear and maintains flatness over repeated use. This hardened construction minimises surface damage during wringing and handling, extending the usable life of the element and reducing the frequency of replacement. The compact geometry contributes to low thermal mass and quicker thermal equilibrium on the bench, which helps when assembling short stacks or performing quick comparison checks under typical workshop conditions. Practical traceability and supply reliability Each item is supplied with clear product identification—GTIN 4054469131405 and SKU M319.060.0—to simplify inventory control and process documentation. The small footprint and recognised standard allow easy integration into existing gauge sets and calibration routines. Backed by Metav’s logistics and technical support, the element supports stable supply chains and consistent access to replacement standards, contributing to uninterrupted production and measurement capability. Contact Metav Werkzeuge for secure supply of Metav IndustryLine gauge blocks and expert advice on integrating the 6 mm reference standard into calibration procedures Technical data Article number: M319.060.0 GTIN: 4054469131405 Material: Special steel, hardened Nominal size: 6 mm Standard: DIN EN ISO 3650 Grade: 0 Weight: 0.009 kg Cross-section: up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm Tariff number: 90173000 Category: Gauge blocks / End gauges Core figures Nominal size: 6 mm Weight: 0.009 kg GTIN: 4054469131405 SKU: M319.060.0 Tariff number: 90173000 Special features DIN EN ISO 3650 Grade 0 compliance Hardened special steel construction Compact reference element for stacks Identifiers: GTIN and SKU for traceability Category: End gauge / Gauge block FAQ What level of accuracy does this gauge block provide? The single gauge block 6 mm is specified as Grade 0 to DIN EN ISO 3650, providing a high level of reference accuracy suitable for inspection and stack building in routine quality control. Which material is used for this gauge block and why is it beneficial? The element is made from special steel, hardened, which enhances wear resistance and maintains flatness during repeated wringing and handling, thereby preserving measurement fidelity over time. Can this gauge block be combined with others for larger reference lengths? Yes, the compact 6 mm nominal size is intended for inclusion in reference stacks; its geometry and standard compliance ensure predictable behaviour when combined with other blocks. How is traceability provided for this product? Traceability is supported by clear identification: GTIN 4054469131405 and SKU M319.060.0, which assist with inventory, documentation and quality records. Is this gauge block suitable for workshop and laboratory use? The Grade 0 specification and hardened construction make it suitable for workshop inspection and calibration routines where a robust, repeatable reference element is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.5 mm Gauge Block Single-End, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Combining Grade 0 accuracy with a compact 6.5 mm nominal size and hardened special steel construction provides a stable, traceable reference for routine calibration and quality checks. Order the gauge block directly via Metav Werkzeuge or consult their specialists for application-specific advice. Single gauge block 6.5 mm — Grade 0 reference, DIN EN ISO 3650 (Metav IndustryLine) The single gauge block 6.5 mm is a hardened length standard designed for precision calibration and dimensional verification in laboratories and workshop metrology. Grade 0 accuracy, DIN EN ISO 3650 Hardened special steel construction Precise 6.5 mm nominal size for calibration Consistent reference for traceable measurement chains A compact gauge block in Grade 0 delivers a reliable baseline for comparative measurements and instrument verification. The compliance with DIN EN ISO 3650 ensures the piece functions as a recognised reference in a calibration chain, supporting repeatable results when used to set or check micrometres, callipers, and other length gauges. The nominal dimension of 6.5 mm provides a practical step within a set of standards, allowing clear interpolation between available sizes while keeping thermal mass low for rapid stabilisation at ambient temperature. Robust materials for everyday workshop use Manufactured from hardened special steel, the block is designed to resist wear and maintain geometry under frequent handling. The compact cross-section of 30 x 9 mm (for sizes up to 10 mm) balances stiffness and manoeuvrability, permitting secure seating in holders and clamping fixtures without undue flex. At approximately 0.009 kg, the component is easy to position during inspection routines, yet heavy enough to sit steadily. The material choice and hardening process reduce surface degradation, extending service life and lowering long‑term replacement costs. Practical traceability and integration into quality systems Using a certified length standard simplifies documentation and audit trails: the block’s conformity to DIN EN ISO 3650 supports quality-system requirements and calibration protocols. The compact end standard is suitable for both shop‑floor checks and laboratory reference tasks, enabling quick verification of measuring instruments before critical measurements. Metav’s positioning as a precision partner further strengthens trust in supply and ongoing availability, backed by decades of experience serving industry and craft with a broad product range and steady logistics from Emmerich. Choose the Metav IndustryLine single gauge block for a compact, durable Grade 0 reference and contact Metav Werkzeuge in Emmerich for tailored delivery and technical guidance via +49 2822 7131930 or info@metav-werkzeuge.com Technical Data Article number: M319.065.0 GTIN: 4054469131429 Tariff number: 90173000 Facts Nominal size: 6.5 mm Weight: 0.009 kg Cross-section: 30 x 9 mm Special features Material: hardened special steel Tolerance grade: Grade 0 Standard: DIN EN ISO 3650 FAQ What accuracy class does this gauge block meet? The single gauge block meets Grade 0 tolerance according to DIN EN ISO 3650, providing a high-precision reference for calibration tasks. Is this block suitable for routine workshop calibration? Yes; the block’s hardened special steel and compact dimensions make it suitable for regular verification of callipers and micrometres in both workshops and metrology labs. How should the block be handled to preserve its accuracy? Handle the gauge block with clean hands or gloves, avoid drops or knocks, and store it in a dry, stable environment to maintain the surface and geometry of the block. Can this product be integrated into a documented calibration process? Yes; because the block complies with DIN EN ISO 3650, it can be used as a documented reference within quality‑control and calibration procedures. What is the article number for ordering and traceability? The article number is M319.065.0 and the GTIN is 4054469131429 for ordering and inventory records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.5 mm Gauge Block, DIN EN ISO 3650 Grade 1, Hardened Special Steel - Metav IndustryLine
Take advantage of Grade 1 precision and a hardened special steel construction for reliable, repeatable reference measurements; the compact 6.5 mm nominal size and robust 30 x 9 mm cross‑section combine stiffness with low mass for easy handling. Order the end gauge directly via Metav Werkzeuge or ask our consultants if clarification is required. End gauge 6.5 mm — DIN EN ISO 3650, Grade 1 (Metav IndustryLine) The End gauge 6.5 mm serves as a hardened reference standard for dimensional inspection in metrology and workshop environments, compliant with DIN EN ISO 3650 for traceable verification of small diameters. Grade 1 accuracy to DIN EN ISO 3650 Hardened special steel construction Nominal 6.5 mm reference size Compact 30 x 9 mm cross‑section, 0.009 kg mass Reduce measurement uncertainty with a certified reference A Grade 1 gauge certified to DIN EN ISO 3650 provides a clear, quantifiable reference when validating inspection equipment or routine checks. As an inspection artefact, the gauge shortens calibration cycles and supports repeatability by supplying a stable, calibrated dimension against which instruments and processes can be checked. This rational advantage translates into fewer rework loops and steadier production output when used as part of a documented quality workflow. Robust material and geometry for consistent readings Manufactured from hardened special steel, the component geometry and a nominal cross‑section of 30 x 9 mm for sizes up to 10 mm give a favourable stiffness‑to‑weight ratio. The low mass of 0.009 kg reduces handling fatigue while the heat‑treated surface improves wear resistance, preserving the reference dimension over extended use. The combination of material choice and compact profile makes the gauge suitable for frequent comparison measurements without compromising dimensional stability. Simple integration into inspection routines Designed for direct insertion into measurement sequences, the gauge supports quick verification tasks and aids in traceable process control. The small nominal size is ideal for bench inspection and instrument checks where space is limited. Correct handling—cleaning contact faces before use and avoiding shock—ensures long service life and consistent performance. Using such a stable reference can noticeably improve first‑pass yield and simplify conformity documentation in daily operations. Sourced for reliability and supply assurance Provided under the Metav IndustryLine umbrella, this end gauge benefits from a supplier network focused on accessible precision. Metav’s position as a European distribution and quality filter means reliable stock management and a broad metrology selection for machine shops, QA departments and specialist dealers. Purchasing through a dedicated partner reduces administrative overhead and supports a traceable supply chain for quality‑oriented teams. Contact Metav Werkzeuge GmbH to discuss the suitability of this Metav IndustryLine end gauge for existing inspection routines or to request further specification details — Metav Werkzeuge is available to advise from Emmerich and to support procurement decisions. Technical data Article number: M319.065.1 GTIN: 4054469131436 Nominal size: 6.5 mm Material: Special steel, hardened Standard: DIN EN ISO 3650 Grade: 1 Facts Weight: 0.009 kg Cross‑section (≤10 mm): 30 x 9 mm Tariff number: 90173000 Special features Category: End gauge Construction: Solid, hardened reference rod Suitable for workshop and laboratory checks FAQ What level of accuracy does this end gauge offer? The end gauge delivers Grade 1 accuracy as specified by DIN EN ISO 3650, providing a stable reference for routine verification tasks. Is the material suitable for frequent use in a production environment? Yes, the gauge is made from hardened special steel, which gives wear resistance and dimensional stability for repeated comparative measurements. Which nominal size is this gauge intended for and what is the relevant geometry? This item is the 6.5 mm nominal size with a cross‑section of 30 x 9 mm for sizes up to 10 mm, offering a compact profile for tight inspection spaces. Can this end gauge be used for instrument checks on small‑bore measurements? The compact 6.5 mm reference is intended precisely for small‑bore and fine dimensional checks in workshop or laboratory workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.5mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Combining the intrinsic stability of ceramic, Grade 1 accuracy and a compact 6.5 mm nominal size ensures a dependable reference standard for routine dimensional checks; order the ceramic gauge block directly via Metav Werkzeuge or consult our specialists for integration advice. Ceramic gauge block 6.5 mm, Grade 1 (DIN 861/1) — Metav IndustryLine The Ceramic gauge block 6.5 mm, Grade 1 (DIN 861/1) is a compact, high‑stability reference standard intended for laboratory and workshop dimensional checks in industrial metrology Ceramic construction for thermal stability Grade 1 accuracy (DIN 861/1) Nominal size 6.5 mm Lightweight 0.011 kg for easy handling Accuracy and repeatability for everyday inspection The compact gauge block is manufactured to Grade 1 according to DIN 861/1, making it suitable as a reference element for routine verification tasks and comparative measurements. The ceramic base material offers low thermal expansion and good wear resistance compared with many metals, which helps to preserve the nominal length during handling and reduces drift between measurements. As a small, stable reference the block supports consistent, repeatable measurements in production sampling and incoming inspection, contributing directly to process reliability and fewer reworks. Practical handling and laboratory integration With a nominal length of 6.5 mm and a weight of 0.011 kg, the block is ergonomically convenient for bench use and combination with optical or mechanical comparators. The lightweight, non‑magnetic nature of the ceramic body simplifies handling and prevents interference in environments sensitive to magnetism. Its compact format suits calibration sets and toolboxes where space is at a premium, while still serving as a reliable building block for length stacks or master references in calibration benches. Confidence through specification and supplier competence Selecting a standard manufactured to recognised norms reduces uncertainty in measurement routines: conformity to DIN 861/1 provides a clear specification for tolerance class and functional use. Metav IndustryLine combines this technical specification with a European distribution and quality filter at Emmerich, backed by decades of metrology supply experience. That combination offers pragmatic assurance for workshops and labs seeking dependable, standardised parts as part of a broader quality strategy. Contact Metav Werkzeuge for procurement and technical advice on integrating the Metav IndustryLine ceramic gauge block into inspection procedures: call +49 2822 7131930 or email info@metav-werkzeuge.com for tailored support. Technical Data Article number: M324.006.5 GTIN: 4054469143019 Material: Ceramic Nominal size: 6.5 mm Weight: 0.011 kg Grade: 1 (DIN 861/1) Customs tariff number: 90173000 Facts Nominal size: 6.5 mm Weight: 0.011 kg GTIN: 4054469143019 Customs tariff number: 90173000 Special features Material: Ceramic Accuracy class: Grade 1 (DIN 861/1) Category: Gauge blocks (Measuring instruments) SKU: M324.006.5 FAQ What tolerance level does Grade 1 (DIN 861/1) indicate? Grade 1 (DIN 861/1) denotes a high level of dimensional accuracy suitable for routine reference and inspection tasks; the ceramic gauge block M324.006.5 meets this standard for consistent comparative measurements. Is the ceramic gauge block magnetic or chemically reactive? Ceramic is non‑magnetic and chemically stable, so the Metav IndustryLine ceramic gauge block is appropriate for environments where magnetic interference or corrosion must be avoided. How can the block be used in a calibration bench or length stack? The 6.5 mm gauge block can be used individually as a reference standard or combined with other blocks to create precise length stacks for calibration and inspection setups in production or laboratory settings. Which identifiers are useful when placing an order or requesting documentation? Please refer to article number M324.006.5 and GTIN 4054469143019 when enquiring about the Metav IndustryLine ceramic gauge block to ensure accurate identification and delivery. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of Grade 1 accuracy, low weight and the inherent stability of ceramic for dependable length references in workshop and laboratory environments; order the gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Metav IndustryLine Ceramic Gauge Block 60 mm — Grade 1 DIN 861/1 The Ceramic gauge block 60 mm, Grade 1 DIN 861/1 is a compact, stable reference standard intended for precision length setting and routine verification in workshops and quality control labs Grade 1 accuracy per DIN 861/1 High-stability ceramic construction Nominal length 60 mm reference standard Lightweight 0.115 kg for easy handling Repeatable length references with proven tolerance class The combination of Grade 1 specification and a 60 mm nominal length provides a reliable reference standard for everyday calibration and setting tasks. Constructed from ceramic, the block resists corrosion and maintains dimensional stability under normal workshop conditions, which supports repeatable measurements when used with micrometers, vernier calipers and setting fixtures. The modest mass of 0.115 kg makes handling straightforward while preserving the stiffness needed for consistent contact during length transfer. Practical use in calibration and setup tasks As a precision accessory, this ceramic block serves to simplify routine setup and inspection work. The Grade 1 classification under DIN 861/1 communicates an industry-recognised tolerance band that fits typical machine‑shop and production‑control needs, reducing uncertainty during gauging tasks. The compact format and low weight enable quick positioning on benches and inside gauge blocks sets, while the non‑metallic construction minimises risk of marking delicate parts during repetitive comparisons. Durability that supports quality workflows A ceramic reference block offers long-term surface integrity and stable performance over repeated handling and comparative measurements. These properties translate into lower maintenance of the reference inventory and more consistent process control at the inspection stage. Where traceability and documented standards are required, the block functions as a robust part of a measurement chain that underpins quality assurance procedures and supports confident decision‑making on production acceptance. For reliable length standards from Metav IndustryLine and tailored advice on using ceramic gauge blocks in production or laboratory settings, contact Metav Werkzeuge GmbH in Emmerich at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss suitability and ordering. Technical data Article number: M324.060 GTIN: 4054469143422 Material: Ceramic Nominal length: 60 mm Weight: 0.115 kg Tolerance class: Grade 1 (DIN 861/1) Tariff number: 90173000 Facts Nominal length: 60 mm Weight: 0.115 kg GTIN: 4054469143422 Tariff number: 90173000 Special features Material: Ceramic Accuracy: Grade 1 per DIN 861/1 Category: End measures / gauge blocks Compact, low-mass design FAQ What is the intended use for this ceramic gauge block? The ceramic gauge block 60 mm, Grade 1 DIN 861/1 is intended as a reference standard for length setting, calibration checks and comparative measurements in workshops and quality control environments. How does Grade 1 under DIN 861/1 affect measurement tasks? Grade 1 specification for the ceramic gauge block defines a recognised tolerance class that fits common machining and inspection tasks, ensuring predictable and repeatable comparative measurements. Is the ceramic gauge block suitable for delicate surfaces? Yes, the ceramic construction of the 60 mm block provides a smooth, wear‑resistant contact surface that reduces the risk of marking delicate workpieces during routine use. Can the block be combined with steel gauge blocks in a set? The ceramic gauge block 60 mm, Grade 1 DIN 861/1 can be used alongside other reference standards for comparative purposes; however, material differences should be considered when critical thermal or magnetic factors affect measurement outcomes. What identifiers are available for inventory and traceability? For traceability the product is listed as M324.060 with GTIN 4054469143422, enabling straightforward inventory control and documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60 mm Gauge Block Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of Grade 1 accuracy, hardened special steel construction and a compact 0.147 kg mass for reliable length references; order the gauge block directly via Metav Werkzeuge or consult the Metav team if further advice is required. End gauge 60 mm, DIN EN ISO 3650 (Grade 1) — Gauge block by Metav IndustryLine The End gauge 60 mm, DIN EN ISO 3650 (Grade 1) is a precision gauge block intended as a length reference for workshop inspections and laboratory verification in industrial metrology. 60 mm gauge block, Grade 1 Hardened special steel construction Compliant with DIN EN ISO 3650 Compact design, mass 0.147 kg Consistent accuracy that improves inspection throughput This gauge block provides a standardised reference with Grade 1 tolerances under DIN EN ISO 3650, reducing uncertainty in comparative measurements. The standard conformity ensures that the block serves as a reliable reference in dimensional checks and calibration chains, which shortens the inspection cycle and lowers the risk of non-conforming parts. Using a standardised length reference minimises the need for corrective rework and supports faster decision-making in production control. Durable material and handling for repeatable results Manufactured from hardened special steel, the block resists wear during routine handling and stacking, preserving measuring faces over long service intervals. The modest mass of 0.147 kg and compact footprint aid comfortable manipulation and safe placement in instrument holders or comparator trays, while the defined cross-section (up to 10 mm: 30 × 9 mm; from 10.1 mm: 35 × 9 mm) offers stable support and easy alignment. The robust construction therefore maintains repeatability and contributes to lower life-cycle costs. Practical integration into inspection workflows As a standardised gauge block, this item fits established stacking procedures and reference sets for length verification in production and maintenance environments. The compact format streamlines storage within inspection kits and allows uncomplicated identification via SKU M319.600.1 and GTIN. Employing a standard gauge block simplifies documentation of measurement sequences and supports traceable quality assurance processes across tools and fixtures. For procurement or technical questions regarding this Metav IndustryLine Grade 1 gauge block, contact Metav Werkzeuge in Emmerich for ordering guidance and detailed product information Technical data Article number: M319.600.1 GTIN: 4054469132259 Customs tariff number: 90173000 Facts Nominal length: 60 mm Weight: 0.147 kg Cross-section: up to 10 mm — 30 × 9 mm; from 10.1 mm — 35 × 9 mm Grade: 1 Special features Material: hardened special steel Standard: DIN EN ISO 3650 Category: Gauge block / End gauge Compact, lightweight design SKU: M319.600.1 FAQ What accuracy class does this gauge block meet? The gauge block complies with Grade 1 tolerances as defined in DIN EN ISO 3650; the End gauge 60 mm is therefore suitable for routine workshop and inspection use where Grade 1 is required. Which material is used for the measuring faces? The measuring faces are made from hardened special steel, providing durable surfaces for repeatable measurements with the End gauge 60 mm. How is the product identified for procurement? The item is listed as SKU M319.600.1 and GTIN 4054469132259 for ordering and inventory traceability. Can the gauge block be used in comparator setups and length standards kits? Yes, the standardised 60 mm length and compliant dimensions make this gauge block suitable for stacking and inclusion in length standards kits and comparator checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60 mm Gauge Block, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of a compact reference gauge that combines DIN EN ISO 3650 conformity and Grade 0 accuracy with robust, hardened special steel construction for dependable length verification in production and inspection tasks. Order the single end gauge directly via Metav Werkzeuge or consult our specialists for application advice. Single end gauge 60 mm — DIN EN ISO 3650, Grade 0 (Metav IndustryLine) Single end gauge 60 mm provides a stable, high-precision reference for comparative measurements and assembly checks across workshops and calibration benches Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel for wear resistance Compact 60 mm length for precise checks Cross-section 35 x 9 mm for improved stiffness Stable reference that supports reliable inspection results The DIN EN ISO 3650 conformity and Grade 0 designation make this gauge a trustworthy reference for routine verification and comparative length checks. As a single, fixed-length end gauge it supplies a well-defined nominal size of 60 mm, enabling straightforward comparisons against parts, fixtures and assembly gauges. The tight manufacturing tolerances associated with Grade 0 reduce ambiguity during visual and tactile inspections and support reproducible outcomes in quality control processes. Robust build for frequent workshop use Manufactured from hardened special steel, the component resists surface wear and preserves measuring geometry over repeated use. The cross-section selected for nominal sizes above 10.1 mm — 35 x 9 mm — increases lateral stiffness and helps keep deflection minimal during handling, while the modest mass (approx. 0.147 kg) makes the gauge easy to position and manoeuvre without excessive bulk. These material and form choices translate into lower maintenance and longer service life under normal workshop conditions. Practical integration into measurement routines The compact format suits bench-top calibration, incoming inspection and spot checks on production lines where a stable, single-length reference is required. The gauge’s clear standard reference (DIN EN ISO 3650) simplifies documentation and audit trails when used alongside calibrated instruments. The article is supplied with distinct identifiers (SKU M319.600.0, GTIN 4054469132242) to assist in inventory control and process traceability, ensuring the item can be recorded and retrieved in procurement and quality systems with confidence. For dependable calibration references choose the Metav IndustryLine single end gauge from Metav Werkzeuge; contact our Emmerich team for tailored technical guidance and prompt supply coordination Technical data SKU: M319.600.0 GTIN: 4054469132242 Nominal size: 60 mm Material: Special steel, hardened Standard: DIN EN ISO 3650 Grade: 0 Facts Weight: 0.147 kg Cross-section: 35 x 9 mm (for sizes >10.1 mm) Tariff number: 90173000 ECLASS: 21170108 Special features Category: Measuring devices → End gauges Cross-section rule: up to 10 mm → 30 x 9 mm; from 10.1 mm → 35 x 9 mm Label: Einzel-Endmaß 60 mm, DIN ISO 3650, Güte 0 FAQ What accuracy class does the gauge meet? The gauge meets Grade 0 accuracy according to DIN EN ISO 3650, providing a high-precision reference for inspection tasks. Is the 60 mm gauge suitable for daily workshop checks? Yes; the compact 60 mm format and hardened special steel construction make the gauge suitable for routine workshop and inspection usage. How is the product identified for procurement and inventory? The article is listed as SKU M319.600.0 with GTIN 4054469132242, allowing straightforward recording in purchasing and quality systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60 x 20 mm Plain Glass Flatness Plate 0.1 μm Accuracy - Metav IndustryLine
Take advantage of the combination of ultra‑fine flatness (0.1 µm), compact 60 × 20 mm format and lightweight handling for reliable small‑part surface checks; order the part directly via Metav Werkzeuge or consult the Metav team for technical guidance and supply. Flat glass M318.223 — 60 × 20 mm, flatness 0.1 µm by Metav IndustryLine The Flat glass M318.223 is a compact reference plate designed for planarity inspection of small components and workshop surface checks 0.1 µm flatness accuracy Compact 60 × 20 mm dimensions Lightweight 0.3 kg for easy handling Accurate planarity as a dependable reference The element is produced to deliver 0.1 µm flatness, which corresponds to a variation of just 0.0001 mm across the surface. Such tolerance provides a clear, objective benchmark when comparing small workpieces or verifying machine set‑up. The component functions as a reference standard for visual and tactile inspections and complements optical comparators and measuring microscopes where a stable planar reference is required. The limited surface deviation minimises interpretation error and supports consistent pass/fail decisions in production and incoming inspection. Small format for precise positioning and repeatable checks With dimensions of 60 × 20 mm and a mass of 0.3 kg, the plate offers straightforward handling and rapid placement on small fixtures or flat test surfaces. The compact footprint reduces the influence of sag and makes positioning on delicate parts easier than larger reference plates, while the modest weight aids one‑person operation and transport within the workshop. This format is particularly suitable for bench‑level checks, fixturing trials and comparative measurements where accessibility and speed matter. Practical contribution to quality workflows Integrating this glass reference into quality routines streamlines surface verification and helps to reduce rework by catching planarity deviations early. The part is compatible with common inspection setups and fits neatly into calibration kits or portable inspection trays. As a clearly defined standard, it enables traceable repeat checks and aids documentation of production quality. The compact reference also supports training scenarios where demonstrable planarity criteria are required to align operator expectations. For traceable small‑part flatness checks or further product details, contact Metav Werkzeuge in Emmerich for supply and technical advice on the Metav IndustryLine Flat glass M318.223 Technical Data SKU: M318.223 GTIN: 4054469128184 Tariff number: 90173000 Numbers / Core technical data Flatness: 0.1 µm Dimensions: 60 × 20 mm Weight: 0.3 kg Special features / Application Designation: Flat glass (Planglas) Application: Checking the flatness of a surface Category: Parallelunterlagen (parallel pads) Brand: Metav IndustryLine FAQ What level of flatness control does this reference provide? The Flat glass M318.223 delivers a 0.1 µm flatness tolerance, making it suitable as a reference for fine surface comparisons and bench‑level inspections. Which inspection tasks suit this compact plate? This plate is intended for planarity checks of small components, fixture testing and comparative measurements where a compact, stable reference improves repeatability. Can the plate be used with optical comparators or microscopes? Yes, the flat surface of the Flat glass M318.223 is compatible with optical comparators and measuring microscopes as a planar reference for visual and dimensional comparison. How should the plate be handled and stored to maintain accuracy? Handle the plate carefully to avoid scratches and store it flat and clean; moderate room temperature and protection from impact preserve the planarity of the reference surface. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600mm Gauge Block Set Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of a traceable length reference that combines DIN EN ISO 3650 tolerances with a hardened special-steel construction; the compact 35 x 9 mm profile keeps bending low for repeatable readings. Order the standard directly via Metav Werkzeuge or request clarification from our consultants for integration into calibration routines. End measure 600 mm — Length reference to DIN EN ISO 3650, Grade 1 (Metav IndustryLine) An End measure 600 mm for use as a calibrated length reference and workshop standard, designed to deliver Grade 1 accuracy for quality assurance and setup verification across machining and inspection environments Grade 1 accuracy to DIN EN ISO 3650 Hardened special-steel construction 35 x 9 mm rectangular profile Reliable reference for consistent verification The 600 mm length comes as a robust length standard manufactured to the tolerances of DIN EN ISO 3650, Grade 1, ensuring a predictable baseline for comparative measurements. The Grade 1 classification means the bar meets strict dimensional limits, which supports reproducible set-ups and quick conformity checks in production control. As a length reference, this component reduces uncertainty when aligning machines, checking gauges or verifying fixtures, making process control more efficient and less prone to systematic error. Durable design that maintains dimensional stability Constructed from hardened special steel, the bar resists wear and surface damage during regular handling. The rectangular 35 x 9 mm section is dimensioned to balance rigidity with manageable mass; this profile reduces deflection over its span and keeps thermal inertia moderate for workshop use. The hardened surface helps preserve the reference faces, prolonging the useful life of the measure and maintaining the accuracy required for repetitive checks without frequent replacement. Practical handling for shop-floor and inspection tasks With a nominal length of 600 mm and a mass of approximately 2.3 kg, the reference bar is heavy enough to remain stable on measurement surfaces yet compact enough for single-person handling on benches or in gauge racks. The straightforward geometry simplifies alignment against workpieces and fixtures, and the clear dimensional specification supports integration into measurement instructions and quality documentation. The durable finish minimises the need for special storage while enabling straightforward cleaning and maintenance routines. Proven suitability from a specialist supplier Supplied under the Metav IndustryLine label, this length standard is ideal where repeatable dimensional checks and routine verification are required. The combination of a standardised tolerance class, hardened construction and a compact rectangular section makes it a dependable choice for calibration labs, toolrooms and production quality checks. Selecting this reference supports consistent output and reduces measurement-related downtime across diverse machining and inspection tasks. For reliable, workshop-ready length standards from Metav IndustryLine, contact Metav Werkzeuge to secure delivery and practical advice on integrating this Grade 1 600 mm end measure into measurement routines at your facility. Technical data Article number: M320.600.1 GTIN: 4054469132532 Nominal length: 600 mm Material: Special steel, hardened Standard: DIN EN ISO 3650 Quality class: Grade 1 Data Weight: 2.3 kg Cross-section: 35 x 9 mm Tariff number: 90173000 Special features Rectangular profile for low deflection Hardened face for wear resistance Designed for workshop and inspection use FAQ What level of accuracy does this end measure provide? The End measure 600 mm complies with DIN EN ISO 3650 as Grade 1, providing the tolerance class specified by that standard for reliable reference measurements. Is the material suitable for regular workshop handling? Yes. The bar is made of hardened special steel, which improves wear resistance and durability during routine use and handling. How heavy and manageable is the 600 mm length standard? The length standard weighs around 2.3 kg, offering a balance between stability on the bench and practical single-person handling. Can the bar be used for fixture and machine set-up checks? The Grade 1 tolerance and the 35 x 9 mm profile are well suited to alignment, fixture verification and quick comparative checks in production and inspection contexts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600mm Gauge Block Set, Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of the combination of DIN EN ISO 3650 Grade 0 accuracy, a hardened special-steel body and a stiff 35 x 9 mm profile for consistently reproducible length standards in the workshop or laboratory; order directly via Metav Werkzeuge or consult the Metav advisors for application-specific guidance. End gauge M320.600.0 — 600 mm Grade 0, DIN EN ISO 3650 (Metav IndustryLine) The End gauge M320.600.0 is a 600 mm hardened special-steel length standard designed for high-precision length verification and production checks in industrial metrology and toolrooms. DIN EN ISO 3650 Grade 0 accuracy Hardened special steel construction 600 mm nominal length, 35 x 9 mm cross-section Robust 2.3 kg mass for stable measurement Assured accuracy where it matters The instrument complies with DIN EN ISO 3650 and is manufactured to Grade 0, making it suitable as a trusted length standard for precision checks. Grade 0 denotes a very tight tolerance band compared with lower classes, which translates into reliable comparative measurements and reduced uncertainty when validating gauges, fixtures or machine setups. The specified accuracy supports routine inspection work and serves as a stable reference for dimensional control tasks in production and incoming‑goods inspection. Stiff, stable construction reduces measurement error Built from hardened special steel with a 35 x 9 mm cross‑section, the bar offers the rigidity needed for long-length standards. The 600 mm nominal length places this instrument in the large-range class (500–1 000 mm), where profile stiffness is essential to keep deflection and bending under control. The unit mass of 2.3 kg contributes to mechanical stability during contact measurement and helps to damp vibrations, so length comparisons yield consistent results across repeated cycles. Practical integration into inspection routines The bar serves as a straightforward reference for setting up verniers, calipers and comparators or for quick go/no-go checks of components and assemblies. Its solid construction allows direct use on flat supports or in gauge stands without additional fixturing for many routine tasks. Because the device is a standardised end measure, documentation of results and traceability within a quality management system become easier to manage, supporting repeatable quality checks across shifts. A reliable partner for precision supply chains Metav IndustryLine supplies this end gauge as part of a broader metrology range intended to make accurate measurement accessible to workshops and industrial users. Metav Werkzeuge’s central logistics in Emmerich ensures dependable delivery and a consistent quality filter for the European market, backed by decades of specialist experience. For buyers seeking a dependable length standard that combines precision, mechanical stability and practical usability, this 600 mm end gauge integrates well into established quality workflows. Contact Metav Werkzeuge today for tailored technical advice and secure the Metav IndustryLine end gauge M320.600.0 for dependable, workshop-ready length standards Technical data Article number: M320.600.0 GTIN: 4054469132525 Norm: DIN EN ISO 3650 Grade: 0 Facts Nominal length: 600 mm Cross-section: 35 x 9 mm Mass: 2.3 kg Tariff number: 90173000 Special features Material: hardened special steel Category: end gauge / end measure Accuracy class: Grade 0 FAQ What level of accuracy does this end gauge provide? The end gauge M320.600.0 is manufactured to Grade 0 under DIN EN ISO 3650, offering a very tight tolerance band suitable for high‑precision comparative work and inspection. Is the material suitable for routine workshop use? Yes; the bar is made from hardened special steel, which provides wear resistance and the rigidity expected of a 600 mm length standard in industrial environments. How does the 35 x 9 mm profile affect measurements? The 35 x 9 mm cross-section increases profile stiffness and reduces bending, which helps to maintain stable measurement results over the 600 mm span. Which applications are typical for this type of length standard? Typical uses include setting and checking calipers, comparator calibration, length verification of machined parts and use as a reference in production quality control; the M320.600.0 is aimed at toolrooms and workshop inspection benches. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60mm Wedge-Tip Measuring Jaw 30×30° For End-Gauge Holder - Metav IndustryLine
The wedge‑shaped measuring jaws deliver defined contact geometry and a compact 60 mm working length for reliable end‑gauge measurements; the small 9 x 8 mm cross‑section combines stability with access to confined features. Order the M317.112 directly via Metav Werkzeuge or ask the consultants if compatibility guidance is required. M317.112 Wedge-shaped Measuring Jaws for End‑Gauge Holder — 60 mm, 30 x 30° (Metav IndustryLine) A set of M317.112 wedge‑shaped measuring jaws intended for use with end‑gauge holders, providing precise 30 x 30° tips for defined contact in inspection and comparative measuring applications. Wedge-shaped 30 x 30° measuring tips 60 mm functional length for tight access Compact cross-section 9 x 8 mm for stability Precision accessory for end-gauge holders Consistent contact geometry for repeatable results The wedge tip profile creates a small, well‑defined contact area that reduces ambiguity at the measurement point. With a 30 x 30° tip the contact force is concentrated and predictable, which improves repeatability when comparing parts or transferring limits from a master to a workpiece. For inspection routines that rely on stable reference contacts, this geometry reduces variability and supports traceable, repeatable outcomes across multiple measurements. Compact form that reaches confined features without compromise A 60 mm working length combines accessibility with controllable handling: the 60 mm dimension enables entry into narrow recesses while the 9 x 8 mm cross‑section maintains torsional stiffness and repeatable alignment. The compact design minimises shadowing and obstruction during fixture setup, making the jaws suitable for close‑quarter checks on small assemblies and in-tool measurements. Lightweight construction supports quick tool changes and reduces operator fatigue during repetitive inspection tasks. Seamless integration to speed up workshop inspection Designed as an accessory for end‑gauge holders, these jaws are a simple way to adapt existing metrology fixtures for specialised contact geometries. The accessory classification ensures straightforward retrofit into holder systems commonly used in comparative gauging. The M317.112 from Metav IndustryLine streamlines inspection workflows by offering a defined contact solution that shortens set‑up times and increases throughput without sacrificing measurement integrity. For procurement or compatibility advice, contact Metav Werkzeuge in Emmerich — their specialists can confirm fitment for specific end‑gauge holders and arrange supply of the M317.112. Technical data Article number: M317.112 GTIN: 4054469167268 Manufacturer: Metav IndustryLine Category: Accessory for measuring devices Facts Functional length: 60 mm Tip geometry: 30 x 30° Cross-section: 9 x 8 mm Weight: 0.01 kg Tariff number: 90173000 Special features Wedge-shaped measuring tips For end-gauge holder applications Accessory classification: Zubehör Short description: Keilspitzen FAQ What is the tip geometry of these measuring jaws? The jaws feature a wedge geometry with 30 x 30° tips, providing a compact, well‑defined contact for comparative measuring and inspection. What working length is provided? The functional length is 60 mm, which balances access to confined features with sufficient handling stability for workshop use. Which holder are these jaws designed to fit? They are designed for use with standard end‑gauge holders; the M317.112 serves as a direct accessory to adapt holder systems requiring wedge‑type contacts. Are these jaws suitable for confined or small‑part measurement? Yes, the compact 9 x 8 mm cross‑section and 60 mm length make the jaws particularly suited to narrow recesses and small assemblies where controlled contact geometry is required. How does this accessory improve inspection workflow? By providing a repeatable contact geometry and easy integration into end‑gauge holders, the accessory reduces set‑up time and increases repeatability in comparative checks. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
65.62/65.75/65.87/66.00 mm Gauge Glass Set For Micrometer Calibration 0.1 µm Accuracy - Metav IndustryLine
Take advantage of an accurately dimensioned reference set that combines 0.1 µm flatness with a compact, four‑plate layout to keep routine micrometre checks fast and reliable. The set supports verification across the 50–75 mm range and offers consistent parallelism (0.006 mm) for reproducible comparisons — order via Metav Werkzeuge or consult our team for selection advice. M318.227 plane-glass set — optical flats for micrometre inspection, 0.1 µm accuracy (Metav IndustryLine) The M318.227 plane-glass set is an optical reference kit for verifying micrometres in the 50–75 mm measuring range, supplied as four precision plates to check anvil parallelism and measuring consistency. 0.1 µm flatness for high-precision checks Four precision plates for 50–75 mm micrometres Parallelism 0.006 mm for reproducible results Total weight 0.5 kg for easy handling Reliable reference for routine micrometre verification The M318.227 set provides an economical, metrology‑grade reference for routine checks of micrometres and small measuring instruments. With a declared flatness of 0.1 µm, the plates serve as a stable, known surface against which anvil faces can be compared. This level of flatness helps to reveal wear, dirt or alignment errors that would otherwise introduce systematic measurement bias. The four plate sizes (65.62 / 65.75 / 65.87 / 66.00 mm) allow cross‑checking across a narrow band of clearances typical for the 50–75 mm micrometre class. Controlled geometry for reproducible comparisons Consistent geometry is central to reproducible verification: the set’s parallelism of 0.006 mm ensures that readings taken across different plates remain comparable. For workshop quality control this reduces scatter between checks and shortens decision cycles for maintenance or rejection. The plates’ compact design and total mass of 0.5 kg make handling straightforward while maintaining sufficient rigidity to avoid bending during short inspection routines. The result is a practical balance of stability and portability for bench‑level metrology. Micro-class suitability for fine mechanical work Classified for the Micro category (measuring range 50–75 mm), this reference kit is tailored to fine mechanical and precision‑assembly environments where space is limited and accuracy matters. The set fits the workflow of tool rooms, small‑parts assembly and repair benches, enabling quick verification without specialised fixtures. Each plate performs as a precision reference to confirm that the measuring instrument remains within its expected behaviour, supporting traceable quality procedures in small to medium production runs. Contact Metav Werkzeuge in Emmerich for specification matching and procurement of the M318.227 plane-glass set from Metav IndustryLine Technical data Article number: M318.227 GTIN: 4054469184289 Set: 4 plates Core specifications Flatness: 0.1 µm Parallelism: 0.006 mm Plate sizes: 65.62 / 65.75 / 65.87 / 66.00 mm Diameter: 30 mm Weight: 0.5 kg Special features Application: Verification of micrometres 50–75 mm Category: Parallel reference plates (parallel gauge plates) Brand: Metav IndustryLine eClass: 21170126 FAQ What measuring range is this set intended for? The set is intended for verification of micrometres in the 50–75 mm measuring range; the plate sizes are matched to that band for comparative checks. How precise are the reference plates? The M318.227 plane-glass set is specified with a flatness of 0.1 µm and a parallelism of 0.006 mm, providing a high‑precision reference for micrometre checks. How many plates are included and what are their sizes? The kit comprises four plates with nominal sizes 65.62, 65.75, 65.87 and 66.00 mm to permit consistent cross‑comparisons within the intended range. How should the plates be used to check a micrometre? Compare the micrometre anvil against a plate surface, record any deviation from the expected reading and repeat across at least two plates to confirm repeatability; use gentle, consistent contact to avoid introducing measurement error. Is the M318.227 suitable for shop‑floor and small lab use? Yes. Its compact dimensions and controlled geometry make it suitable for bench‑level quality checks in tool rooms, small assembly operations and precision workshops. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of Grade 1 accuracy, a 7 mm nominal length and the material benefits of ceramic for a stable reference standard; order the gauge block directly via Metav Werkzeuge or consult our advisors for specification matching. Ceramic gauge block 7 mm — Grade 1 DIN 861/1 (Metav IndustryLine) A ceramic gauge block 7 mm serving as a compact, high-precision dimensional reference for calibration, inspection and fine workshop set-ups. Grade 1 accuracy to DIN 861/1 Durable ceramic with low thermal expansion Nominal length 7 mm for precise references Lightweight at 12 g for easy handling Reliable reference for small-scale precision A compact gauge block specified as Grade 1 under DIN 861/1 provides a dependable dimensional reference where repeatable measurements matter. The nominal length of 7 mm is ideal for setting standards in fine inspection tasks and fixture checks. As a standardised reference piece, it supports traceable measurement processes and helps to reduce setup times when comparing or verifying micrometric readings on small components. Material advantages that reduce measurement uncertainty Manufactured from ceramic, the block benefits from intrinsic low thermal expansion and excellent wear resistance, which together lower the risk of drift during short-term use in variable workshop environments. Ceramic material also resists corrosion and surface deterioration, ensuring the reference dimension remains stable over many cycles of comparison. These material properties contribute directly to reduced measurement uncertainty and increased confidence in everyday calibration tasks. Practical handling and workshop integration The compact design and low mass make the reference block simple to store and manoeuvre in calibration benches or inspection stages. Its size suits close-up checks, go/no-go assemblies and comparative measurements where a small, stable standard is required. When integrated into routine inspection workflows, the block helps standardise results across shifts and operators, supporting faster quality decisions and fewer rejects. Metav IndustryLine — precision made accessible Metav IndustryLine supplies this block as part of a broad precision portfolio that aims to democratise access to high-quality measurement tools. With an established European presence and a comprehensive product range, Metav supports purchasers with consistent sourcing and a transparent supply chain. The availability of robust reference standards from a single supplier simplifies procurement and supports reliable workshop calibration practices. Contact Metav Werkzeuge to discuss suitability for specific applications and secure Grade 1 reference standards — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and ordering support Technical Data Article number: M324.007 GTIN: 4054469143026 Material: Ceramic Nominal length: 7 mm Grade: 1 (DIN 861/1) Weight: 0.012 kg Tariff number: 90173000 Facts Nominal length: 7 mm Weight: 0.012 kg Grade specification: DIN 861/1 Special features Category: Gauge blocks / End gauges Manufacturer: Metav IndustryLine Application: Dimensional reference and inspection FAQ What level of accuracy does this gauge block provide? The block is specified as Grade 1 according to DIN 861/1, which designates it as a high‑precision reference suitable for workshop and inspection use. Why choose a ceramic block rather than metal? Ceramic offers low thermal expansion and high surface stability, so the block maintains its reference dimension better under typical temperature fluctuations and resists corrosion. What are the nominal dimensions and mass of the reference piece? The item has a nominal length of 7 mm and a mass of approximately 0.012 kg (12 g), identified as SKU M324.007. For which tasks is this reference block most suitable? The block is well suited to calibration, comparative measurements, and setting up measuring instruments where a small, stable standard is required. Is this block part of a larger product range? Yes, the block is offered under Metav IndustryLine as a compact reference within a broader catalog of precision measuring equipment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7 mm Gauge Block Single End, Hardened Special Steel, DIN EN ISO 3650, Grade 0 - Metav IndustryLine
Take advantage of Grade 0 accuracy and conformity to DIN EN ISO 3650 combined with a hardened special steel finish for reliable, repeatable checks in workshops and calibration benches; order the single end gauge directly via Metav Werkzeuge or ask our consultants if needed. Single end gauge 7 mm — End gauge (DIN EN ISO 3650) by Metav IndustryLine A single end gauge 7 mm designed for dimensional verification and reference measurements in calibration labs and quality control workflows. Grade 0 tolerance to DIN EN ISO 3650 Hardened special steel construction Compact 7 mm nominal size for precision checks Lightweight 0.009 kg for easy handling Laboratory-grade accuracy for routine reference measurements The Grade 0 tolerance, specified to DIN EN ISO 3650, provides a proven basis for trusted dimensional checks. As a small reference artefact with a 7 mm nominal size, this end gauge serves as a stable reference for comparators, micrometres and gauge blocks when confirming instrument performance. The tight manufacturing tolerances reduce uncertainty in calibration chains and simplify cross-check procedures; this is particularly valuable in quality control where consistent, reproducible reference values are required. Durable material for stable long-term performance Constructed from hardened special steel, the gauge resists wear and retains its measuring faces under frequent use. The chosen material and heat treatment enhance surface stability and minimise dimensional drift, so maintenance intervals are extended and service disruption is reduced. The compact format and low mass (approx. 0.009 kg) make handling straightforward while the robust finish preserves the reference faces against minor knocks and shop-floor contamination. Easy integration into inspection routines and documentation Small size and standard compliance simplify inventorying and traceability in inspection plans. The item is supplied with a clear identification (SKU: M319.070.0) and can be entered into quality management systems as a reference artefact for routine verification tasks. For shops aiming to centralise precision tools, this end gauge slots into a set of reference standards or a master gauge block kit, supporting systematic checks without occupying excessive bench space. Why this choice benefits operations Selecting a standardised, grade-controlled end gauge shortens decision cycles during incoming goods inspection and in-process control: fewer ambiguous results, faster pass/fail decisions and a reduced need for repeat measurements. Combined with Metav’s distribution and quality oversight, the item contributes to smoother calibration workflows and predictable measurement outcomes — a pragmatic investment in operational reliability. For assured Grade 0 precision order via Metav Werkzeuge or contact Metav Werkzeuge GmbH for consultation at info@metav-werkzeuge.com / +49 2822 7131930 Technical Data SKU: M319.070.0 GTIN: 4054469131443 Category: End gauges (Messgeräte > Endmasse) Article description: Single end gauge 7 mm, DIN EN ISO 3650, Grade 0 Tariff number: 90173000 Facts Nominal size: 7 mm Weight: 0.009 kg Grade: 0 (Güte 0) Special features Material: hardened special steel Standard: DIN EN ISO 3650 Cross-section: up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm Category path: Messgeräte › Endmasse FAQ What does Grade 0 mean for everyday use? Grade 0 indicates a high-precision tolerance class according to DIN EN ISO 3650; the single end gauge 7 mm meets this class and is suitable as a reliable reference for routine checks and instrument verification. Is this end gauge suitable for workshop calibration? Yes; the end gauge is intended for dimensional verification in both workshop and calibration-bench environments, where its conformity to DIN EN ISO 3650 supports consistent inspection results. How should the end gauge be handled and stored? Handle the gauge with clean, dry hands or gloves and store it in a protective box or drawer to avoid knocks and contamination; regular visual inspection of the measuring faces helps to identify wear early. Can this gauge be used as part of a master set? The compact 7 mm size and standardised tolerance class make the product an appropriate component of a master gauge block or reference set for traceable measurement routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7 mm Gauge Block, Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of DIN EN ISO 3650 conformity, Grade 1 accuracy and a hardened special steel construction to secure repeatable dimensional references in calibration and inspection tasks; order directly via Metav Werkzeuge or consult the team for specification advice. Gauge block 7 mm (Gauge block, Grade 1, DIN EN ISO 3650) — Metav IndustryLine The Gauge block 7 mm is a compact precision reference standard for dimensional calibration and inspection in calibration labs and precision workshops. DIN EN ISO 3650, Grade 1 accuracy Nominal size 7 mm reference standard Hardened special steel for stability Compact cross-section 30 x 9 mm for up to 10 mm Reliable reference for consistent measurement results As a Grade 1 reference manufactured to DIN EN ISO 3650, this precision block provides well-defined tolerances that support repeatable measurements and quality control processes. The normative specification ensures that the block serves as a stable reference in comparative checks and assembly set-ups; traceable conformity to the stated standard reduces uncertainty when establishing master dimensions. The compact design limits thermal and handling effects, helping to maintain stability during routine use. Material integrity and geometry that minimise measurement error Made from special steel, hardened, the block combines material stiffness with long-term wear resistance, which contributes to consistent contact surfaces over many cycles. The chosen 30 x 9 mm cross-section (applicable for sizes up to 10 mm) offers a favourable stiffness-to-size ratio that reduces bending and local distortion during stacking or when used as a reference on small fixtures. Low mass supports precise manual handling while avoiding excessive thermal influence from the operator. Practical traceability and shop-floor integration Identification via GTIN and the clear supplier SKU simplifies inventory control and calibration management; the compact format is straightforward to store in instrument trays or reference sets. As a precision reference, the block is suited to forward-facing inspection routines, comparative calibrations and as a component of gauge sets where consistent nominal dimensions must be preserved. The Metav IndustryLine quality workflow and European distribution from Emmerich provide a dependable supply chain for workshops and calibration facilities. Secure Grade 1 gauge blocks from Metav IndustryLine through Metav Werkzeuge in Emmerich — contact info@metav-werkzeuge.com or call +49 2822 7131930 for technical advice and delivery details Technical data Article number: M319.070.1 GTIN: 4054469131450 Tariff number: 90173000 Category: Gauge blocks Facts Nominal size: 7 mm Weight: 0.009 kg Cross-section: 30 x 9 mm (for up to 10 mm) Grade: 1 Special features Material: Special steel, hardened Standard: DIN EN ISO 3650 Category path: Messgeräte → Endmasse FAQ What tolerance class does this gauge block meet? The Gauge block 7 mm (Metav IndustryLine, SKU M319.070.1) meets Grade 1 tolerances as specified in DIN EN ISO 3650, providing defined limits for routine comparative measurements. What material is the gauge block made from? The Gauge block 7 mm (Metav IndustryLine, SKU M319.070.1) is manufactured from special steel, hardened, which supports durable, stable contact surfaces for repeated use. How is this gauge block typically used in a calibration workflow? The Gauge block 7 mm (Metav IndustryLine, SKU M319.070.1) is used as a reference standard for dimensional calibration, comparative checks and as part of assembled gauge sets where a fixed nominal is required. Is this block suitable for regular workshop use or only for laboratory environments? The Gauge block 7 mm (Metav IndustryLine, SKU M319.070.1) is suitable for both calibration laboratories and precision workshops where a Grade 1 reference standard is required for routine inspection and set-up tasks. How can the product be identified for stock and calibration records? The Gauge block 7 mm (Metav IndustryLine, SKU M319.070.1) is identifiable by its GTIN: 4054469131450 and supplier article number M319.070.1, which facilitates inventory tracking and calibration documentation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7.5 mm Gauge Block Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
The hardened special-steel 7.5 mm gauge block delivers a stable, high-accuracy reference for laboratory and workshop length standards; combined with DIN EN ISO 3650 Grade 0 conformity and compact 30 × 9 mm cross-section, it supports reproducible calibration and setting tasks. Order directly via Metav Werkzeuge or consult our specialists for selection and application advice. Single gauge block 7.5 mm — Grade 0, DIN EN ISO 3650 (Metav IndustryLine) The Single gauge block 7.5 mm is a hardened precision reference intended for traceable length standards, master measurements and high-accuracy setting operations in metrology and quality control environments. DIN EN ISO 3650 Grade 0 accuracy Hardened special steel construction Compact reference for precision calibration Stable reference for reproducible measurements This gauge is manufactured to DIN EN ISO 3650 and supplied in Grade 0, making it suitable where a stable, high-accuracy reference is required. The block’s nominal size 7.5 mm and precisely machined faces provide a repeatable contact surface for comparisons and stack-based length standards. As a hardened reference in special steel, it limits wear and dimensional drift over time, which reduces the need for frequent retesting and maintains measurement integrity in inspection routines. Robust material and compact geometry for handling Constructed from hardened special steel, the unit combines surface stability with practical handling characteristics. The cross-sectional profile of 30 × 9 mm for sizes up to 10 mm gives good stiffness relative to its size, minimising bending and improving contact repeatability during stacking or single-block use. The compact format also simplifies storage and short-distance transport within a laboratory, while the hardened finish offers resistance to light knocks and common workshop influences. Application benefits and practical use cases As a precision reference, this block is ideal for transfer standards, gauge stacks, and setting tools where quick, reliable verification of small lengths is needed. The accurately lapped faces ensure consistent seating against gauges, pins or measuring machine anvils, enabling efficient calibration workflows in both production and test labs. For smaller instrument adjustments and master-setting tasks, the compact block permits one-handed positioning and rapid integration into measurement routines. Quality assurance and procurement confidence Sourcing this unit under the Metav IndustryLine label provides an additional assurance of supply-chain oversight and selection for professional users. The combination of an established standard (DIN EN ISO 3650) and hardened special-steel construction supports long service life and dependable in-use performance. For procurement and inventory planning, the clear specification and compact footprint help standardise master references across inspection benches and workstations. For precision that integrates with existing reference stacks and calibration processes, contact Metav Werkzeuge to discuss the Metav IndustryLine gauge block and complementary master standards. Technical data Article number: M319.075.0 GTIN: 4054469131467 Nominal size: 7.5 mm Material: Special steel, hardened Standard: DIN EN ISO 3650 Grade: 0 Cross-section: 30 × 9 mm (for sizes ≤ 10 mm) Weight: 0.009 kg Tariff code: 90173000 Facts Nominal dimension: 7.5 mm Mass: 0.009 kg Cross-section dimension: 30 × 9 mm Harmonised tariff number: 90173000 Special features Conforms to DIN EN ISO 3650 Grade 0 accuracy for high-precision reference work Hardened special-steel for wear resistance Compact format for easy handling and stacking FAQ What level of accuracy does this gauge provide? The Single gauge block 7.5 mm meets DIN EN ISO 3650 Grade 0, providing a high-accuracy reference suitable for precision calibration and master measurements. Which material is used for the gauge block and how does it affect performance? The block is made from hardened special steel, which gives stable surfaces and good wear resistance, enhancing long-term reproducibility of the 7.5 mm reference. Can the block be combined with other gauge blocks for stack measurements? Yes — the block’s lapped faces and compact cross-section are designed for stacking alongside other blocks to build composite standards and transfer lengths. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
ensure traceable length calibration with gauge blocks
gauge blocks, also called slip gauges or end gauges, are precision length standards designed to transfer exact measures during calibration and setup. Manufactured and graded for metrological use, they provide the reference dimensions needed to verify and adjust measuring instruments in industrial workshops and calibration labs.
how gauge blocks work and where they are essential
gauge blocks are used to create known lengths by wringing individual blocks together or by using a single block as a reference. length calibration in industry commonly relies on parallel gauge blocks, while angle, cylinder and sphere end gauges serve specialised tasks. these blocks are produced in steel, ceramic or carbide, and their material choice balances wear resistance with thermal behaviour. regular calibration—typically performed annually—by DAkkS-accredited laboratories ensures traceability. the highest-precision reference work, class K, is certified by the PTB using laser techniques; classes 0, 1 and 2 are tested under progressively less controlled conditions (class 0 in a climate-controlled lab, class 1 in a standard measurement room, class 2 in production).
measurable benefits that cut downtime and uncertainty
- consistent, traceable length standards reduce rework and measurement disputes by enabling reliable instrument calibration.
- choosing the correct material (steel, ceramic, carbide) extends service life and limits wear in high-use environments.
- selecting the right accuracy class (K, 0, 1 or 2) matches calibration effort to application needs and avoids over‑specification.
- annual calibration by accredited labs maintains documented compliance and supports quality systems such as ISO.
why Metav is a smart partner for precision standards
Metav combines specialist knowledge with a broad range of measurement technology, making the procurement of gauge blocks straightforward and dependable. with over 48,000 customers and more than 250,000 products stocked from Emmerich, Metav acts as a pragmatic quality filter for European workshops, reducing supplier complexity and ensuring consistent supply.
In short, gauge blocks deliver traceable, material‑appropriate and class‑matched references that keep calibration workflows efficient and auditable.
faq
what materials are gauge blocks available in and why does it matter?
gauge blocks are typically supplied in steel, ceramic or carbide. material choice affects wear resistance, stability and thermal expansion; selecting the right material for your environment optimises longevity and measurement stability.
how often should gauge blocks be calibrated?
industry practice is an annual calibration cycle, carried out by DAkkS-accredited laboratories, though frequency can be increased depending on usage and required uncertainty.
what do the accuracy classes k, 0, 1 and 2 indicate?
the classes denote graded tolerances and test conditions: K is the highest precision (certified by PTB with laser measurement), class 0 is checked under climate-controlled lab conditions, class 1 in a normal measurement room and class 2 in production environments.
are parallel gauge blocks always used for length calibration?
yes; for length calibration the parallel gauge blocks are the primary standard because they provide exact planar faces for wringing and stacking to create precise lengths.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com