End gauges for precise length calibration
End gauges provide exact reference lengths for calibrating measurement instruments and ensuring consistent dimensional accuracy in metalworking and inspection processes. Used in production and laboratory settings, these end gauges—made from steel, ceramic or carbide—allow technicians to compensate for wear and thermal effects and maintain measurement traceability, especially when employed alongside parallel end gauges, cylinder gauges and calibration masters. Classes 0, 1 and 2 define practical tolerance levels for workshop, inspection-room and production use respectively, delivering the repeatable precision required for machining and quality control.
45mm Gauge Jaw R5×15, 9×8 mm Shank, Pair - Metav IndustryLine
Take advantage of precise, compact mounting and repeatable contact geometry thanks to the R5 × 15 mm measuring tip, the 45 × 9 × 8 mm shank and the supplied set of two; ideal for quick replacement and minimal setup time. Order the measuring jaw directly via Metav Werkzeuge or ask our consultants if needed. Measuring jaw R5 x 15 mm (shank 45 x 9 x 8 mm) — Metav IndustryLine accessory A compact measuring jaw that provides reliable point contact for small-feature inspection and secure attachment to standard measurement holders in industrial metrology. R5 tip for precise contact 45 × 9 × 8 mm shank for secure mounting Supplied as a set of two Improved repeatability through defined contact geometry The compact measuring jaw delivers a consistently defined contact point thanks to its R5 × 15 mm tip geometry. This profile reduces variation at the point of measurement, making comparative checks and single-point inspections more reliable. For workshop and inspection-room routines, the measured benefit is a reduction in rework and faster pass/fail decisions, because the defined radius simplifies alignment against fillets, grooved features and small diameters. The component is presented as a ready-to-fit accessory, allowing maintenance teams to replace worn tips without recalibrating the entire setup. Compact design for straightforward handling and fast replacement With a nominal length of 45 mm and a low individual mass, the jaws are designed for easy manual handling and quick exchange. The 45 × 9 × 8 mm shank ensures a snug fit in holders that accept rectangular mounting bars, so stability during measurement is retained even under repeated use. Supplied in pairs, the set supports parallel checks or mirrored installations, cutting downtime during tool changes. The compact format is particularly advantageous where space is limited or where fixtures demand short overhangs to preserve rigidity. Practical compatibility for inspection and small-part production Engineered for accessory use within industrial metrology, the jaws suit tasks such as contact probing, step checks and registering against defined edges. The combination of a precise tip radius and a standardised shank cross-section enables easy integration into common holders and gauge adaptors used in machine shops and quality departments. As a Metav IndustryLine accessory, the product contributes to a modular approach: spare parts are simple to stock, individual components are replaced rather than entire assemblies, and measurement workflows remain efficient and predictable. For replacement parts and reliable delivery from Emmerich, contact Metav Werkzeuge for ordering and technical guidance via info@metav-werkzeuge.com or call +49 2822 7131930 — Metav's consultants will advise on fitment and availability Technical Data Article number: M317.107 GTIN: 4054469127378 Tariff number: 90173000 Facts Length: 45 mm Cross-section (shank): 9 × 8 mm Tip geometry: R5 × 15 mm Weight (per piece): 0.01 kg Supplied as: set of 2 Special features Accessory for measuring instruments and holders Compact mounting for short overhangs Defined contact radius for repeatable measurements Designed for workshop and inspection use FAQ What is the mounting size of these measuring jaws? The measuring jaw comes with a 45 × 9 × 8 mm shank suitable for standard rectangular holders and gauge adaptors. Can these jaws be used for small-diameter checks and fillets? Yes, the R5 × 15 mm tip geometry is intended for precise contact on small diameters, grooves and filleted features. Are the jaws supplied individually or as a set? They are supplied as a set of two, which supports parallel checking or quick replacement strategies. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
47 pcs Ceramic Gauge Block Set Grade 1, DIN EN ISO 3650, Antimagnetic, Supplied In Case - Metav IndustryLine
Take advantage of precise, low‑maintenance reference standards combined with thermal stability for repeatable measurements and secure transport. Order the set directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic Gauge Block Set M321.471 (Grade 1, DIN EN ISO 3650) by Metav IndustryLine The Ceramic Gauge Block Set provides stable reference standards for calibration tasks in workshops and laboratories, designed for routine dimensional checks and master setting applications. Grade 1 accuracy to DIN EN ISO 3650 Antimagnetic ceramic construction Stable dimensions up to 100 mm Delivered in protective transport case Consistent accuracy for reliable reference measurements Gauge blocks are fundamental as reference standards for setting measuring instruments and checking device accuracy. This Grade 1 set complies with DIN EN ISO 3650, ensuring defined tolerances for routine calibration tasks. The blocks are made from ceramic, a material chosen for its low thermal expansion and high wear resistance; this reduces drift during short‑term temperature changes and extends service life compared with softer materials. The antimagnetic nature further eliminates magnetic distortion during contact measurements, providing a stable basis for traceable dimensional work. Practical design that supports workshop workflows The collection covers lengths up to 100 mm and is shaped with cross‑sections optimised for stiffness and handling; smaller sizes maintain reduced mass while longer blocks provide reach without sacrificing stability. Delivered in a robust protective transport case, the set is suitable for mobile inspection or secure workshop storage. Maintenance is minimal: the blocks are specified as antimagnetic and pre‑treated so that the usual degreasing before use and oiling after use are not required, simplifying preparation and reducing handling steps while preserving measurement integrity. A pragmatic choice from a trusted supplier As part of the Metav IndustryLine, this ceramic set combines workshop practicality with industrial standards. Choosing these reference blocks supports efficient quality routines and reduces downtime during instrument set‑up or batch control. Metav’s established distribution from Emmerich ensures reliable supply and direct access to product information and spare parts. For production environments that prioritise reproducibility and simple upkeep, the set provides a cost‑effective way to raise the baseline precision of everyday measurement tasks. Contact Metav Werkzeuge today at info@metav-werkzeuge.com or +49 2822 7131930 to discuss suitability for specific applications and secure delivery of the Metav IndustryLine ceramic gauge block set M321.471 with Grade 1 traceability from DIN EN ISO 3650 Technical Data Article number: M321.471 GTIN: 4054469132686 Manufacturer: Metav IndustryLine Facts Pieces per set: 47 Material: ceramic Weight: 2.6 kg Max block length: 100 mm Cross-section up to 30 mm: 30 x 9 mm Cross-section from 40 mm: 35 x 9 mm Special features Grade 1 to DIN EN ISO 3650 Antimagnetic No degreasing before use or oiling after use required Delivered in protective transport case FAQ What level of accuracy can be expected from these gauge blocks? The ceramic gauge block set M321.471 is Grade 1 and manufactured to DIN EN ISO 3650, delivering the reproducible tolerances associated with that grade for routine calibration and inspection tasks. Is any special maintenance required for the ceramic blocks? No. The blocks are antimagnetic and treated so that degreasing before use and oiling after use are not necessary, which reduces routine maintenance and handling steps. Can the set be used outside a controlled laboratory environment? Yes. The material properties of ceramic—low thermal expansion and good wear resistance—make this set suitable for workshop and production environments, especially when stored and transported in the supplied protective case. Does the set include a transport case and how are the pieces protected? The set is delivered in a protective transport case that secures each block for mobile inspection and safe storage, helping to maintain the condition of the reference surfaces. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
47 pcs Precision Gauge Block Set 1.005–100 mm Hardened Special Steel DIN EN ISO 3650, In Plastic Case - Metav IndustryLine
Taking advantage of a hardened special‑steel construction and compliance with DIN EN ISO 3650, this parallel end gauge set delivers repeatable alignment and dimensional control across inspection and assembly tasks; supplied complete in a protective transport case for safe handling — order the set directly via Metav Werkzeuge or consult our specialists for tailored advice. Parallel end gauge set (DIN 861/0) — hardened special steel, precision‑ground Parallel end gauge set (DIN 861/0) for high‑precision spacing, alignment and inspection tasks in workshop and production environments Hardened special‑steel construction Precision to DIN EN ISO 3650 Precision‑ground parallel faces Supplied in protective transport case Reliable, repeatable alignment for inspection and assembly The set of gauge blocks is engineered to ensure consistent parallelism and minimal variation during repeated measurements. Manufactured from hardened special steel, each block is precision ground to the tolerances required by the stated standard DIN EN ISO 3650, which supports traceable results in quality control. The combination of material hardness and precision grinding reduces wear and preserves contact geometry, supplying the stability needed for alignment tasks and fixture setting. Built for workshop handling and long service life A design emphasis on durability means the blocks resist deformation in everyday use. The hardened construction and ground faces limit surface damage and allow secure stacking or shim‑setting without rapid deterioration. Because the set is delivered in a protective transport case, handling and storage are simplified, improving workplace organisation and reducing the risk of accidental damage during transport or on the shop floor. Organised set composition for efficient workflow The collection contains an organised range of thicknesses presented for quick selection and combination; the precise gradation of blocks supports fine adjustment without time‑consuming trial‑and‑error. Clear identification of sizes and a compact case format cut process time during setup and inspection. For shop floors and inspection stations where repeatability and speed matter, the set streamlines measurement routines and reduces setup variability. Contact Metav Werkzeuge for specification checks, calibration options and to procure the Metav IndustryLine parallel end gauge set directly from Emmerich — expert advice is available by phone or email Technical data Article number: M318.470 GTIN: 4054469129082 Tariff number: 90173000 Weight: 2.6 kg Facts Pieces per set: 47 Standard: DIN EN ISO 3650 Material: Special steel, hardened Set type: Parallel end gauge set Special features Precision‑ground parallel faces Protective transport case included Suited for alignment, shimming and inspection tasks Category: End gauge set FAQ Are the blocks manufactured to an international standard? The set is produced to the requirements of DIN EN ISO 3650, ensuring conformity for workshop and inspection use. What material is used for the gauge blocks? Blocks are made from hardened special steel, chosen for wear resistance and dimensional stability. How is the set delivered and organised? The gauge blocks are supplied in a protective transport case to facilitate safe storage and straightforward handling on the shop floor. Is a calibration certificate included with the set? A calibration certificate is not automatically indicated in the product data; please contact Metav Werkzeuge to arrange calibration options or to confirm supplied certification for the specific delivery. Which applications suit this end gauge set? The set is intended for alignment, fixture setup, shimming and dimensional verification where precise, stable parallels are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
47mm Gauge Block Set Class 1 47-Piece 1.005–100mm Range, Precision - TECWERK
Take advantage of the combination of Grade 1 accuracy, robust steel construction and a carefully balanced size composition for reliable workshop measurement routines; order the set directly via Metav Werkzeuge or ask the consultants for application advice. TECWERK Parallel gauge block set – Grade 1, steel construction The TECWERK Parallel gauge block set offers high-accuracy gauge blocks for workshop inspection and light laboratory use, presented as a precision tool for measurement and calibration tasks. Grade 1 accuracy standard Steel construction for stable measurements Versatile size composition for workshop use Designed for inspection and calibration tasks Precision where consistent results are required Gauge blocks are a fundamental tool in dimensional metrology and the TECWERK Parallel gauge block set is engineered to deliver consistent precision across repeated measurements. The Grade 1 classification denotes a high level of manufacturing accuracy suitable for many industrial inspection and setup tasks; this reduces uncertainty in subsequent machining and measuring operations. The blocks are produced to be flat and finished so that individual blocks can wring together to form exact lengths, enabling quick build-up of standard sizes without reliance on guesswork. For quality-focused workshops, that translates into fewer measurement errors and more predictable production outcomes. Stable material and a composition built for versatility Manufactured from steel (STA), the blocks provide dimensional stability under normal workshop conditions. Steel offers a balance of hardness and machinability that supports frequent handling while retaining flatness and parallelism. The set’s composition covers small incremental lengths through larger reference increments, which simplifies the process of composing required measures and shortens setup times at the bench. The carefully arranged size composition supports efficient combination of blocks for both fine adjustments and larger nominal lengths, meaning fewer substitutions and faster changeovers in inspection routines. Fit for inspection, calibration and routine metrology The design intent is clear: support routine measurement tasks in toolrooms, inspection benches and maintenance departments. The set is particularly useful where repeatable reference lengths are required for calibration checks, go/no-go fixtures and verification of depth or clearance settings. Because the collection follows a recognised tolerance class, it integrates well into traceable workflows and quality documentation. Practical handling considerations—flat storage, gentle cleaning and avoidance of corrosive environments—help maintain the blocks’ performance over time and protect the investment in measurement certainty. Contact Metav Werkzeuge for tailored technical advice and to secure the TECWERK Parallel gauge block set; Metav Werkzeuge can advise on compatibility with existing equipment and dispatch from Emmerich—email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000851624NW SKU/UID: 2000851624NW Product type: Parallel gauge block set Manufacturer: TECWERK Material: Steel (STA) Tolerance class: Grade 1 Set composition: 1 x 1.005 mm / 20 x 1.01–1.20 mm / 7 x 1.30–1.90 mm / 9 x 1–9 mm / 10 x 10–100 mm Facts Pieces: 47 Packaging unit: 1 Tolerance class: 1 Special features Steel construction for dimensional stability Broad size composition for versatile measurements Intended for workshop inspection and calibration tasks FAQ What accuracy level does this gauge block set provide? The TECWERK Parallel gauge block set is manufactured to Grade 1 tolerance, providing accuracy suitable for many workshop inspection and calibration applications where reliable repeatability is required. Is the set suitable for routine calibration tasks in a toolroom? Yes, the set’s composition and Grade 1 classification make it well suited for routine calibration checks and verification tasks commonly performed in toolrooms and maintenance departments. What material are the blocks made from? The blocks are made from steel (STA), chosen for stable dimensional behaviour under normal workshop conditions and frequent handling. How should the gauge blocks be cared for to preserve accuracy? The blocks should be stored flat, cleaned of debris and light oils after use, and kept away from corrosive environments to maintain surface condition and accuracy of the TECWERK gauge block set. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
47mm Parallel Gauge Set Tolerance Class 2 47-Piece, 1.005–100mm Range - TECWERK
Combine tolerance class 2 accuracy with a comprehensive 47-piece steel set to standardise workshop checks and speed up inspection routines; order the set directly via Metav Werkzeuge or consult our specialists for application advice. Parallel end gauge set, tolerance class 2 – TECWERK (47-piece, steel) The Parallel end gauge set serves as a compact suite of reference standards for dimensional inspection and calibration in machine shops and quality control labs. Tolerance class 2 accuracy 47-piece set for wide size coverage Made from steel for durability Comprehensive size selection for calibration Reliable reference standards that reduce measurement uncertainty The set provides tolerance class 2 reference elements designed to deliver repeatable dimensional checks in routine quality control. By using calibrated end measures as a comparative standard, measurement uncertainty in daily inspection tasks is reduced, which helps to lower scrap rates and maintain consistent part quality. The term tolerance class 2 denotes a defined accuracy band appropriate for most workshop and production environments, offering a balance between precision and robustness. Versatile set composition to streamline calibration tasks A carefully composed assortment covers small to mid-range dimensions, meaning fewer tool changes during set-up and a shorter time to measure parts. The set composition is: 1 × 1.005 mm; 20 × 1.01–1.20 mm; 7 × 1.30–1.90 mm; 9 × 1–9 mm; 10 × 10–100 mm, which supports a broad spectrum of common inspection requirements. This variety allows the set to act as a flexible reference for comparative checks with micrometres and precision calipers, simplifying workflow and saving operator time when checking batches. Durable construction for long service life and stability Manufactured in steel (STA), the elements are engineered to resist wear and maintain dimensional stability under regular use. Steel construction provides a robust contact surface for repetitive measurement tasks and supports thermal stability better than softer materials in everyday workshop conditions. The result is a reference set that preserves its measuring capability over extended periods, reducing the need for frequent replacement and ensuring continuity in calibration routines. Fits into existing quality systems and supports traceability The set is suitable for integration into ISO-aligned inspection procedures as a local reference for incoming inspection, in-process checks and final approval. Using this gauge suite improves internal traceability when paired with documented measurement procedures, and it can serve as a baseline for comparison against calibrated master standards. For workshops aiming to professionalise their metrology, the collection of calibrated end measures delivers measurable improvements in process control and audit readiness. Request the TECWERK 47-piece parallel end gauge set through Metav Werkzeuge for dependable workshop calibration supplies — contact our Emmerich team at info@metav-werkzeuge.com or +49 2822 7131930 for technical guidance and prompt delivery Technical Data Article number: 2000851625NW Label: Parallelendmaßsatz Tol.-Kl.2 47tlg.STA TECWERK Product type: Parallel end gauge set Core data Set size: 47 pieces Tolerance class: 2 Composition (pieces/sizes): 1 × 1.005 mm; 20 × 1.01–1.20 mm; 7 × 1.30–1.90 mm; 9 × 1–9 mm; 10 × 10–100 mm Special features Material: steel (STA) Intended use: dimensional reference for inspection and calibration FAQ What accuracy can be expected from these end measures? The TECWERK parallel end gauge set conforms to tolerance class 2, offering accuracy suitable for general workshop calibration and routine inspection tasks. How does the set composition support everyday measuring tasks? The mix of small and larger sizes in the 47-piece set covers common measurement ranges, making it practical for frequent comparative checks with micrometres and precision calipers. Is the material suitable for heavy use in a workshop environment? Yes, the individual elements are made from steel (STA), which provides wear resistance and dimensional stability for regular handling and inspection. Can these gauges be integrated into documented quality procedures? The set is designed to serve as a workshop reference for ISO-aligned routines, supporting traceability when used alongside documented measurement protocols. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
47pc Carbide Parallel Gauge Set DIN EN ISO 3650, Assorted Sizes, Supplied in Case - Metav IndustryLine
The combination of carbide construction, conformity to DIN EN ISO 3650 and an organised transport case ensures long‑term wear resistance and reliable set‑up across repeat inspections; benefit from durable, standardised parallels for efficient fixture alignment. Order the Carbide Parallel Gauge Block Set M322.471 directly via Metav Werkzeuge or ask our consultants if needed. Carbide Parallel Gauge Block Set M322.471 — 47-piece, DIN EN ISO 3650 The Carbide Parallel Gauge Block Set M322.471 is a precision alignment set designed for fixture set‑up, inspection benches and shop‑floor toolmaking, delivering standard‑compliant parallels for repeatable measurements Carbide construction for long-term wear resistance Conforms to DIN EN ISO 3650 standard Precision ground for reliable alignment Supplied in transport case for safe storage Consistent precision where it matters Accuracy is the primary concern when aligning jigs, setting up vises or checking run‑out. The gauge blocks in this set are precision ground and manufactured from carbide, which reduces wear and dimension drift during repeated use. Compliance with DIN EN ISO 3650 provides a recognised quality baseline, so measurement traces and setup procedures remain consistent across shifts and locations. This predictable behaviour shortens setup times and reduces rework, directly supporting productivity goals on the shop floor. Durability that reduces lifecycle costs A hard‑wearing material such as carbide significantly extends the service life of parallels compared with softer metals. The result is fewer replacements and more stable reference surfaces over time, which lowers total cost of ownership for inspection and tooling departments. The robust construction also tolerates routine handling and light impacts during transport, so investments in high‑precision tooling deliver sustained returns without frequent recalibration or refurbishment. A practical set for alignment and inspection tasks Supplied as a complete set, the parallels are arranged to cover common alignment and setup needs in machine shops and quality control. The organised configuration simplifies the selection process during fixture preparation and speeds repetitive tasks. A compact, complete set helps maintain a tidy working area and supports systematic procedures in assembly, inspection and maintenance operations, improving both efficiency and workplace ergonomics. Safe transport and traceable conformity The set is supplied in a purpose‑made transport case to protect the components in transit and storage, preserving the ground surfaces and reducing downtime due to damage. Traceability is supported through the standard reference: DIN EN ISO 3650, which facilitates documentation in quality systems. For procurement and stock control the set is listed with its SKU and GTIN, allowing straightforward integration into inventory processes and ensuring the right reference parts are used across multiple sites. For reliable, standard‑compliant parallels and professional advice, contact Metav Werkzeuge to check availability or request guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M322.471 GTIN: 4054469132723 Material: Carbide Standard: DIN EN ISO 3650 Set: 47 pieces Facts Pieces per set: 47 Weight: 3.7 kg Customs tariff number: 90173000 Contents (sizes): 1x1,005 / 20x1,01–1,2 / 7x1,3–1,9 / 9x1–9 / 10x10–100 Special features Precision ground parallels Carbide for wear resistance Supplied in transport case (plastic or wooden) Suitable for fixture alignment and inspection FAQ What applications are these parallels designed for? The gauge set is intended for fixture set‑up, alignment, bench inspection and general toolroom use; the Carbide Parallel Gauge Block Set M322.471 supports repeatable reference surfaces for these tasks. Does the set comply with an industrial standard? Yes, the set is manufactured to DIN EN ISO 3650, which is stated for the Carbide Parallel Gauge Block Set M322.471 and assists with quality documentation and audit requirements. How does the carbide material benefit everyday use? Carbide offers superior wear resistance compared with softer steels, so the parallels in this set keep their dimensions and surface quality longer, reducing maintenance and replacement frequency. Is the set supplied ready for use and protected in transit? The parallels are supplied in a transport case to protect finished surfaces during handling and storage, preserving alignment accuracy for immediate use. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
47x10-100mm Parallel Gauge Block Set 47 Pieces, Hardened Special Steel, DIN EN ISO 3650, Wooden Case - Metav IndustryLine
Take advantage of a compact, standards-compliant set that combines durable hardened steel, a comprehensive size range up to 100 mm, and safe transport in a protective case for reliable shop-floor and laboratory use; order directly via Metav Werkzeuge or request bespoke advice from our consultants. Parallel gauge block set M318.471 — 47-piece, hardened special steel (DIN EN ISO 3650) by Metav IndustryLine Parallel gauge block set designed for precision stacking, setting gauges and verification tasks in production and inspection environments 47 precision blocks in set Hardened special steel construction Standards-compliant to DIN EN ISO 3650 Supplied in protective transport case Reproducible accuracy for calibration and fixture setting The set is engineered to deliver consistent, stackable reference lengths that support repeatable setups and calibration routines. Conformity with DIN EN ISO 3650 ensures interchangeability with other gauge-block systems and provides a clear basis for traceable measurements. The combination of precise nominal sizes and wear-resistant hardened special steel reduces dimensional drift during regular use, which simplifies tolerance control and shortens inspection cycles in both workshop and quality departments. Practical coverage that reduces handling and increases efficiency A total of 47 pieces gives a logical spread of nominal lengths up to 100 mm, enabling rapid assembly of target dimensions without excessive stacking. This range is suitable for setting up fixtures, checking clearances and producing master references for machining tasks. The balanced selection of blocks reduces the need for frequent tool changes, so measurement and setup times fall and throughput improves; the robust material and finish also mean fewer replacements over the tool’s service life. Durable storage and portable protection for everyday use Delivered in a sturdy protective case, the set is ready for secure storage and safe transport between job sites or across the shop floor. The compact overall weight of the set supports simple handling while the hardened steel composition preserves contact surfaces against wear from repeated wringing and stacking. As a result, recalibration intervals are extended and the set maintains its role as a dependable reference in both routine inspections and setup operations. For professional measurement reliability choose the Metav IndustryLine gauge block set and contact Metav Werkzeuge for detailed technical information or a tailored quotation. Technical data Article number: M318.471 GTIN: 4054469129099 Category: Endmasse SKU: M318.471 Facts Weight: 2.6 kg Pieces per set: 47 Maximum block length: 100 mm Standard: DIN EN ISO 3650 Special features Material: Special steel, hardened Delivery: Protective transport case included Standards referenced: DIN 861/1 and DIN EN ISO 3650 Set composition: Sizes from 1.005 mm to 100 mm FAQ What size range does the set cover? The set covers a practical range from approximately 1.005 mm up to 100 mm, supplied as a coordinated selection of precision blocks. Is the set suitable for workshop and laboratory use? Yes, the Metav IndustryLine parallel gauge block set is designed for both shop-floor applications and precision inspection tasks where stable reference lengths are required. What material are the gauge blocks made from? The blocks are manufactured from hardened special steel, chosen for its wear resistance and dimensional stability under normal handling. Does the set comply with recognised standards? The collection complies with DIN EN ISO 3650 and references DIN 861/1, ensuring compatibility with other standard gauge block systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
47x10–100mm Ceramic Gauge Block Set Grade 0, Antimagnetic, DIN EN ISO 3650 - Metav IndustryLine
The combination of ceramic construction, Grade 0 accuracy to DIN EN ISO 3650 and an organised set of reference blocks provides reliable, low‑maintenance dimensional standards for everyday workshop and inspection tasks — order directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic Parallel Gauge Block Set M321.470 — Grade 0 accuracy, up to 100 mm The Ceramic Parallel Gauge Block Set delivers stable, non‑magnetic reference faces for general workshop and metrology use, ideal for routine checks, tool setting and dimensional verification within the standard measurement range. Grade 0 accuracy to DIN EN ISO 3650 Antimagnetic ceramic construction Comprehensive 47-piece organised set Durable transport case included Consistent reference accuracy reduces rework and inspection time Engineered to Grade 0 tolerances and referenced to DIN EN ISO 3650, this ceramic set offers a dependable baseline for comparative measurements and calibration checks. The inherent dimensional stability of ceramic minimises thermal drift compared with many metals, so reference values remain consistent during typical workshop temperature swings. As a result, process control becomes more predictable and the time spent on repeat checks or rework is reduced, improving throughput in daily production and quality assurance routines. Low maintenance, robust handling for everyday workshop use Made from wear‑resistant ceramic and finished with antimagnetic properties, the kit eliminates the need for routine degreasing and re‑oiling before or after use, reducing upkeep and contamination risks. The 47‑piece composition covers a practical size range up to 100 mm, supplied in a protective transport case that organises components for safe storage and rapid retrieval. This combination supports efficient bench work: reference faces are ready for immediate use, handling is simplified and storage protects accuracy between uses. Versatile application across inspection and tool setup tasks The set is suitable for machine shops, fixture workshops and inspection benches that require a standard‑range, high‑quality reference. As parallel gauge blocks, they serve as trustworthy masters for setting calipers, dial indicators and comparative gauges, and for validating measurement instruments. The sturdy cross‑sections and carefully graded sizes make the collection a practical alternative to single‑piece replacements, supporting repeatable setups and a consistent measurement chain in routine production environments. For tailored advice on integrating this Metav IndustryLine ceramic set into existing inspection routines, contact Metav Werkzeuge and request expert guidance or delivery options. Technical data Article number: M321.470 SKU: M321.470 GTIN: 4054469132679 Standard: DIN EN ISO 3650 Tariff number: 90173000 Core data Pieces per set: 47 Weight: 2.6 kg Max block length: 100 mm Special features Material: Ceramic Antimagnetic finish Delivery in durable transport case Cross-section: up to 30 mm → 30 x 9 mm; from 40 mm → 35 x 9 mm Sizes included: 1 × 1.005 mm; 20 × 1.01–1.2 mm; 7 × 1.3–1.9 mm; 9 × 1–9 mm; 10 × 10–100 mm FAQ What accuracy class does the set meet? The set meets Grade 0 accuracy in accordance with DIN EN ISO 3650, providing repeatable reference values suitable for standard workshop and inspection tasks. Which materials are the blocks made from and what advantage does that give? The blocks are manufactured from ceramic, offering excellent dimensional stability, wear resistance and antimagnetic behaviour, which lowers maintenance compared with metallic masters. Is this set suitable for routine machine shop checks? Yes — the configuration and size range (up to 100 mm) make the set well suited for workshop measurement, tool setting and process control tasks where reliable, standard‑range reference blocks are required. Does the product include a calibration certificate? The available product data does not state the inclusion of a calibration certificate with the set. How are the blocks supplied for storage and transport? The collection is supplied neatly organised in a protective transport case to simplify handling, storage and transport between inspection locations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
47x10–100mm Parallel Gauge Set 47 Pieces Hardened Special Steel DIN EN ISO 3650, In Plastic Case - Metav IndustryLine
Benefit from the combination of hardened special steel, conformity with DIN EN ISO 3650 and a complete 47-piece set that streamlines precision set‑up and reference checks; order the Parallel gauge block set directly via Metav Werkzeuge or ask the consultants for application support. Parallel gauge block set M318.472 — hardened special-steel, DIN EN ISO 3650 Parallel gauge block set M318.472 is a compact length‑reference system for setting, calibrating and checking measuring instruments in workshops and metrology environments. Hardened special-steel construction Complies with DIN EN ISO 3650 Complete 47-piece gauge block set Consistent reference for repeatable set‑ups The set serves as a practical reference standard for routine dimensional checks and setup tasks. Individual blocks are made from hardened special steel, delivering stable dimensions under normal workshop conditions and reducing thermal and mechanical drift during short‑term measurements. As a result, the set supports reliable reproducibility of measurements, which shortens adjustment cycles and reduces the need for repeated machining trials — a direct benefit for production workflows and quality control routines. Built to recognised metrology standards Conformity with DIN EN ISO 3650 underlines the set’s suitability for calibration and inspection benches where traceable length standards are required. The construction and finish of the blocks make them appropriate for integration into typical inspection processes in metalworking and component assembly. Clear standard alignment offers procurement confidence for technical buyers and inspection engineers who require documented compatibility with established metrological practices. Practical composition for everyday workshop use Arranged as a 47-piece assortment, the set covers the common step sizes used for gauge stacking and setting micrometres, comparators and height gauges, enabling quick creation of many nominal lengths with minimal stacking. The total transport weight of 2.6 kg makes the set portable between workstations while remaining substantial enough for stable handling. The assortment format reduces downtime when configuring measuring equipment and provides straightforward inventory for workshop metrology kits. For a dependable length standard from Metav IndustryLine, request the Parallel gauge block set via Metav Werkzeuge or contact Metav’s application advisors in Emmerich for customised selection advice. Technical Data SKU: M318.472 GTIN: 4054469129105 Tariff number: 90173000 Facts Pieces per set: 47 Weight: 2.6 kg eClass: 21179208 Special features Material: Special steel, hardened Standard: DIN EN ISO 3650 Category: Gauge blocks / Endmasse FAQ What materials are the blocks made from? The blocks are manufactured from hardened special steel, giving the Parallel gauge block set M318.472 good dimensional stability for routine metrology tasks. Which standard does the set conform to? Conformity with DIN EN ISO 3650 is stated for the set, making it suitable where recognised length standards are required. How many pieces are included in the set? The set contains 47 individual blocks, supplied as a complete assortment to build common nominal lengths. Is the set suitable for workshop use or only for laboratories? The construction balances robustness and precision, making the set appropriate for both workshop inspection benches and general metrology applications. Can the set be used to set micrometres and height gauges? Yes, the assortment is designed for stacking and reference creation used in setting micrometres, height gauges and comparators; the set supports common workshop procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
481.1mm Calibration Gauge Grade 1, DIN 861/1, DIN EN ISO 3650/1 - Metav IndustryLine
Take advantage of a laboratory-grade reference gauge that combines stable length control, industrial conformity and robust material choice for dependable instrument checks. The precise 481.1 mm length in Grade 1 quality supports consistent verification of calipers and micrometres; order directly via Metav Werkzeuge or ask the sales team for application advice. Calibration end standard 481.1 mm, Grade 1 (Metav IndustryLine) The Calibration end standard 481.1 mm is a precision reference gauge for checking calipers and micrometres in workshop and inspection environments. Grade 1 accuracy according to DIN 861/1 Reference length 481.1 mm for standard checks Made from specially selected steel Conforms to DIN EN ISO 3650/1 Ensuring measurement reliability with a stable reference A calibrated reference bar provides the rational basis for repeatable measurement control: the 481.1 mm nominal length in Grade 1 quality functions as a stable, traceable standard for routine verification of length-measuring tools. Using a dedicated reference gauge reduces uncertainty in pass/fail decisions during incoming inspection and in-process checks, because the physical artefact replaces indirect estimations with a defined length. The conformity to DIN EN ISO 3650/1 indicates that the component is manufactured to recognised metrology tolerances, which supports documentation and auditability of quality processes. Durable construction for workshop use and long service life Constructed from special steel, the bar balances rigidity and wear resistance to maintain length stability under normal workshop conditions. The chosen material minimises changes from handling and ambient conditions, which means fewer surprises during comparison measurements. At approximately 1.9 kg, the mass provides a solid feel that helps avoid unintended bending while being manageable for single-person handling. The result is a reference piece that preserves form and function over many calibration cycles, reducing the need for replacement and lowering total cost of ownership. Simple integration into quality workflows and verification routines Designed as a practical reference gauge, this end standard integrates quickly into inspection benches for direct comparison with dial, vernier and digital calipers as well as micrometres. Traceable reference lengths are essential when establishing measurement baselines, performing instrument checks after maintenance, or validating quality control equipment before critical runs. The compact, well‑defined geometry aids fast setup and repeatable alignment, supporting smoother quality audits and quicker decision making during production stops. For reliable reference standards from Metav IndustryLine, request the M318.209 calibration end standard via Metav Werkzeuge to equip the workshop with a stable 481.1 mm Grade 1 reference that supports consistent verification of measuring instruments. Technical Data Article number: M318.209 GTIN: 4054469128115 Manufacturer: Metav IndustryLine Facts Nominal length: 481.1 mm Grade: 1 Weight: 1.9 kg Tariff number: 90173000 Special features Material: special steel Standard: DIN EN ISO 3650/1 Intended use: reference gauge for checking calipers and micrometres FAQ What is the primary purpose of this end standard? The calibration end standard M318.209 serves as a precision reference gauge for checking and comparing calipers and micrometres to a defined length of 481.1 mm. What does Grade 1 signify for the end standard? Grade 1 denotes a high-accuracy tolerance class suitable for workshop and inspection use where reliable reference lengths are required; it ensures narrower permissible deviation than general-purpose grades. Which material is used and why does it matter? The bar is made from special steel, chosen for dimensional stability and wear resistance so that the reference length remains consistent under normal handling and storage. Is this standard produced to recognised metrology norms? Yes, the product is manufactured in accordance with DIN EN ISO 3650/1, indicating conformity with established dimensional reference requirements. Can this gauge be used for routine calibration checks? The gauge is designed for routine verification tasks, enabling fast comparison measurements that support repeatable instrument checks and quality control processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Taking advantage of Grade 1 conformity and the inherent dimensional stability of ceramic, this compact 5 mm gauge block delivers a dependable reference for routine checks and workshop standards; order the Ceramic gauge block 5 mm directly via Metav Werkzeuge or consult the Metav specialists for application advice. Ceramic gauge block 5 mm, Grade 1 DIN 861/1 — Metav IndustryLine The Ceramic gauge block 5 mm, Grade 1 DIN 861/1 serves as a compact, high-stability length standard for calibration tasks and repeatable setting operations in metrology benches and quality workshops. Grade 1 accuracy to DIN 861/1 Low thermal expansion ceramic Wear-resistant measuring surface Compact 5 mm nominal size Precision where repeatability counts The block is specified to Grade 1 under DIN 861/1, offering a reference that helps reduce measurement uncertainty in everyday calibration and setting tasks. As a short, fixed-length standard the element provides a stable basis for verifying gauges, comparators and setting devices; the small nominal length of 5 mm makes it especially convenient for fine adjustments and quick verification sequences. The clear conformity to an established standard supports traceable quality-control routines and simplifies documentation in inspection protocols. Material benefits that improve workflow Manufactured from ceramic, the block combines low thermal expansion with a wear-resistant measuring surface, which together deliver long-term dimensional stability under normal workshop conditions. These material characteristics minimise length drift with temperature fluctuations and extend interval times between re-measurements or replacements. The non-corroding and chemically inert nature of the ceramic also reduces maintenance needs, so the standard remains reliable without special surface treatments or frequent refurbishment. Practical use in the workshop and laboratory The compact format and light weight support quick handling during setup and transfer between instruments. As a fixed-length reference it is well suited to daily check routines, gauge comparison and as a transfer standard for setting micrometres and other length-measuring instruments. The block’s simple geometry eases alignment on flat anvils and within fixtures, while the robust surface preserves contact quality over repeated use. For integration into inspection processes, the block complements both hand-held and bench-top measurement equipment, lending itself to systematic quality workflows without adding complexity. For precise and reliable reference standards, order the Metav IndustryLine Ceramic gauge block through Metav Werkzeuge or contact the Metav consultants at info@metav-werkzeuge.com / +49 2822 7131930 for application guidance and stock information Technical Data Article number: M324.005 GTIN: 4054469142982 Manufacturer: Metav IndustryLine Facts Nominal length: 5 mm Weight: 0.009 kg Grade: 1 (DIN 861/1) Customs tariff number: 90173000 Special features Material: Ceramic Compact, stable reference standard Wear-resistant measuring faces FAQ What accuracy class does this gauge block meet? The block meets Grade 1 accuracy according to DIN 861/1; the Ceramic gauge block 5 mm, Grade 1 DIN 861/1 (Metav IndustryLine, SKU M324.005) is intended as a workshop-quality reference for routine checks. Is ceramic a suitable material for a gauge block? Yes—ceramic offers low thermal expansion and wear resistance, making the ceramic standard suitable for stable length references and repeatable measurements in both shop-floor and calibration environments. Can the block be used to set micrometres and comparators? The compact 5 mm fixed length is ideal for setting and quick verification of micrometres and comparator jaws; the ceramic measuring faces support consistent contact conditions during such procedures. How should the block be handled and stored? Handle the block carefully to avoid impact or contamination of the measuring faces; store in a clean, dry container or protective sleeve when not in use to preserve surface integrity and dimensional stability. What identifiers are available for ordering or inventory? Use SKU M324.005 or GTIN 4054469142982 when ordering or referencing the Ceramic gauge block 5 mm, Grade 1 DIN 861/1 from Metav IndustryLine. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5 mm Gauge Block Grade 1 DIN EN ISO 3650 Hardened Special Steel - Metav IndustryLine
Take advantage of DIN EN ISO 3650 conformity and the hardened special‑steel construction for a stable, repeatable reference length. The compact cross‑section minimises wear while the Grade 1 tolerance supports reliable inspection routines. Order the gauge block via Metav Werkzeuge or ask our consultants for specification support. End gauge 5 mm — Gauge block, DIN EN ISO 3650, Grade 1 (Metav IndustryLine) The End gauge 5 mm is a hardened precision gauge block designed for traceable length checks and reference tasks in workshop inspection and calibration environments. DIN EN ISO 3650 compliant, Grade 1 Hardened special steel construction Compact 5 mm nominal length, 30 x 9 mm cross-section Certified conformity and what it means for accuracy The block meets DIN EN ISO 3650 as a Grade 1 length standard, which ensures narrow permissible deviations and consistent repeatability for routine checks. As a compact, fixed‑length reference, this gauge block replaces uncertain measurement setups and simplifies verification of micrometre and dial gauge readings. The nominal 5 mm size provides a stable short‑range standard suitable for comparing measuring instruments and setting up machine offsets, helping to reduce cumulative measurement error in production and inspection processes. Robust material and geometry for daily workshop use Constructed from hardened special steel, the block offers good wear resistance and dimensional stability under normal workshop conditions. The compact cross‑section of 30 x 9 mm (applicable for nominal lengths up to 10 mm) concentrates mass where it supports rigidity while keeping handling easy and safe. The low mass and robust finish reduce the risk of surface damage during handling; when used as a reference in assembly or inspection stations, the material choice lowers maintenance needs and extends service life compared with softer standards. Practical role in quality assurance and process control Used as a short master for calibrations and comparative checks, this precision block supports traceable measurement chains and quick verification routines on the shop floor. Incorporating a fixed‑length gauge into daily checks streamlines quality control, shortens inspection time and provides a tangible benchmark for tolerance decisions. The compact design lends itself to storage with other small standards and to integration in inspection kits, supporting fast, repeatable checks without complex setup. Choose the Metav IndustryLine 5 mm gauge block for Grade 1 conformity and hardened special‑steel construction — contact Metav Werkzeuge for purchase and technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M319.050.1 GTIN: 4054469131375 Label: End gauge 5 mm, DIN EN ISO 3650, Grade 1 Facts Nominal length: 5 mm Weight: 0.008 kg Cross‑section: 30 x 9 mm Special features Material: special steel, hardened Standard: DIN EN ISO 3650 Grade: 1 Tariff number: 90173000 FAQ What tolerance class does this gauge block meet? The gauge block conforms to DIN EN ISO 3650 as Grade 1, providing tight permissible deviations suitable for reliable workshop reference use. Is the material resistant to daily workshop handling? Yes — manufactured from hardened special steel, the block is designed for good wear resistance and dimensional stability during routine checks. For which measurements is a 5 mm block typically used? A 5 mm gauge block is commonly used as a short‑range reference for micrometres, dial gauges and comparative checks, serving as a quick master for calibration tasks. Can this block be combined with other gauges for stepped lengths? Yes — small gauge blocks are often stacked or compared against other standards to build up reference lengths or to verify compound measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5 mm Gauge Block Single End, Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of a compact, DIN EN ISO 3650-compliant length reference that combines high manufacturing quality with straightforward workshop handling; the hardened special steel construction and Grade 0 tolerance provide a reliable baseline for routine checks and setting tasks. Order this single gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Single gauge block 5 mm — durable Grade 0 length standard from Metav IndustryLine A Single gauge block 5 mm designed as a primary length reference for inspection benches and workshop calibration tasks, offering stable geometry and conformity with DIN EN ISO 3650. Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel for dimensional stability Compact cross-section 30 x 9 mm for workshop use Nominal length 5 mm, mass 0.008 kg Dependable reference for repeatable measurements This compact length standard serves as a direct, high-quality reference when establishing or checking measuring instruments. As a Grade 0 gauge block produced to DIN EN ISO 3650, it supplies the repeatability required for everyday calibration work and makes a tangible difference in process reliability. The item functions as a stable baseline for verifying micrometres, vernier calipers and comparator setups, reducing downtime caused by uncertain references and simplifying routine verification procedures. Robust construction that supports consistent results Manufactured from hardened special steel, this gauge block resists wear and preserves its geometry across many handling cycles. The prescribed cross-section 30 x 9 mm (applicable for nominal lengths up to 10 mm) provides a favourable stiffness-to-weight ratio, so the standard remains easy to position while minimising deformation under normal contact forces; the mass is approximately 0.008 kg. These attributes translate into fewer re-measurements and a lower risk of incidental distortion during set-up, which in turn supports faster, more reliable inspection routines. Practical integration into workshop workflows The piece is intended as a straightforward single block for direct use on the shop floor or in a measuring room. Its compact size and conformity to the recognised standard make it suitable for inclusion in master sets or as a stand‑alone reference for daily checks. Where traceability and repeatability matter, this block enhances measurement confidence through an established standard, enabling technicians to maintain consistent production quality and to document conformity more easily. Choose the Metav IndustryLine single gauge block 5 mm for a compact, Grade 0 length standard and contact Metav Werkzeuge in Emmerich for ordering details and practical advice on integration into existing quality procedures. Technical data Article number: M319.050.0 GTIN: 4054469131368 Tariff number: 90173000 Material: Special steel, hardened Nominal size: 5 mm Standard: DIN EN ISO 3650 Grade: 0 Mass: 0.008 kg Cross-section: 30 x 9 mm (≤ 10 mm) Facts Nominal length: 5 mm Weight: 0.008 kg Cross-section dimensions: 30 x 9 mm GTIN: 4054469131368 Tariff number: 90173000 Special features DIN EN ISO 3650 compliant Grade 0 accuracy Hardened special steel construction Compact workshop-sized gauge block Single end measure suitable for master sets FAQ What tolerance class does this gauge block meet? The single gauge block 5 mm meets Grade 0 tolerances according to DIN EN ISO 3650, providing a precision level suitable for workshop calibration and routine inspection. Is the material suitable for frequent use in a workshop environment? Yes. The gauge block is made of hardened special steel, which offers wear resistance and stable geometry under normal handling typical for shop-floor use. Can this block be used as a reference for setting micrometres and calipers? Yes. The 5 mm block from Metav IndustryLine is intended as a reference for setting and checking micrometres, vernier calipers and similar length gauges. What are the physical dimensions and mass of the block? The nominal length is 5 mm, cross-section 30 x 9 mm (for nominal sizes up to 10 mm), and mass approximately 0.008 kg. Which article number should be quoted when ordering or requesting documentation? Please quote article number M319.050.0 (GTIN 4054469131368) when ordering or asking for technical documentation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.1/10.3/15.0/20.2/25.0 Gauge Block Set For Micrometers, Hardened Special Steel, Supplied In Case - Metav IndustryLine
Take advantage of precise verification and robust construction: the set combines hardened special steel gauge pieces with conformity to DIN EN ISO 3650/1, enabling consistent micrometre checks and long service life. Supplied in a protective case for safe transport, the set is available direct from Metav Werkzeuge or via our consultants for specification advice. M318.200 inspection gauge set by Metav IndustryLine — DIN EN ISO 3650/1, hardened special steel The M318.200 is a compact inspection gauge set intended to verify and validate micrometre performance in workshop and laboratory environments Five precision end gauges to ISO standards Hardened special steel for long service life Supplied in a protective transport case Ideal for micrometre verification and checks Precision that supports reliable measurement decisions The set is designed for reproducible checks and routine verification of micrometres. The individual pieces follow DIN EN ISO 3650/1 and are made from hardened special steel, which reduces wear and maintains dimensional stability over repeated use. Using reference gauges that conform to recognised standards minimises uncertainty in go/no‑go decisions and supports consistent quality control. The compact range addresses the common verification points encountered in everyday workshop inspection, translating conformity into measurable operational benefits. Built for regular use in workshop and inspection environments Delivered as a single five‑piece set, the components are sized for typical micrometre checks and are robust enough for daily handling. The protective case secures the gauges during transport and storage, reducing the risk of nicks or contamination that would otherwise compromise readings. At an overall net weight of around 0.5 kg, the set is portable yet substantial enough to feel precise in hand; the aged and hardened steel composition gives both tactile assurance and resistance to deformation under standard handling. Traceability and applicability for quality workflows The set supports traceable verification steps within inspection routines: each gauge provides a fixed, known length for comparison against a micrometre’s indication. Conformity to DIN 863 and DIN EN ISO 3650/1 makes the set suitable for workshop calibration loops, incoming inspection and routine checks where documented references are required. By integrating these reference pieces into regular verification schedules, measurement drift can be detected early, reducing rework and strengthening process reliability. Discuss application requirements with Metav Werkzeuge in Emmerich and request the M318.200 inspection gauge set or tailored advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M318.200 GTIN: 4054469127958 Product category: End gauges Facts Net weight: 0.5 kg Sizes (mm): 5.1 / 10.3 / 15.0 / 20.2 / 25.0 Pieces per set: 5 Tariff code: 90173000 Special features Material: special steel, aged and hardened Standards: DIN 863; DIN EN ISO 3650/1 Delivered in protective case Intended use: micrometre verification and inspection FAQ What is the primary purpose of this gauge set? The M318.200 inspection gauge set by Metav IndustryLine serves as fixed reference lengths to verify and check the accuracy of micrometres in workshops and quality labs. Are the gauges suitable for daily shop-floor use? Yes, the hardened special steel construction and protective case make the M318.200 set appropriate for routine shop-floor verification and transport between stations. Which standards do the gauges comply with? The components conform to DIN 863 and DIN EN ISO 3650/1, providing documented reference lengths for standardised measurement procedures. How many pieces are included and what sizes are they? The set contains five pieces with nominal sizes of 5.1 mm, 10.3 mm, 15.0 mm, 20.2 mm and 25.0 mm, selected to cover common micrometre checks. Can the set be used to establish traceability in inspection reports? Yes, the M318.200 set is intended to support traceable verification steps within inspection routines, assisting documented quality workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.1/10.3/15/20.2/25 mm Gauge Block Set With Flat Glass Ø30mm, Hardened Special Steel - Metav IndustryLine
Precision reference blocks in hardened special steel provide a stable, standards-compliant basis for micrometer verification up to 25.0 mm. Combined with the included Ø30 mm flat glass, the set supports consistent workshop checks and traceable measurement routines; order directly via Metav Werkzeuge or consult their specialists for application advice. Gauge block set for micrometers M318.200.P — six precision blocks, DIN EN ISO 3650/1 Gauge block set for micrometers M318.200.P is a compact verification kit for routine checks and calibration support in production and inspection environments, designed to match micrometer measuring ranges and reference requirements. Standards-compliant: DIN EN ISO 3650/1 Hardened special steel construction Six precision blocks plus Ø30 mm flat glass Compact set for micrometer verification Reliable conformity for routine verification The set is built to support repeatable measurement procedures by adhering to recognised standards. Compliance with DIN EN ISO 3650/1 and DIN 863 gives a clear normative baseline for dimensional checks, helping to ensure that micrometer readings are verifiable against an established reference. By offering a stable reference up to 25.0 mm, the kit reduces uncertainty during daily calibration tasks and contributes to reliable quality control documentation. Robust materials and practical durability Manufactured from aged and hardened special steel, the blocks combine surface stability with resistance to wear that is typical for workshop use. The hardened finish minimises deformation under handling, so reference dimensions remain consistent over many cycles. The included flat glass Ø30 mm serves as an optical and tactile reference for flatness checks and helps to confirm the condition of measurement faces after routine use, extending the practical service life of the gauges. Compact scope tailored to micrometer applications The contents—six precision gauge blocks and a Ø30 mm flat glass—cover the common ranges required for micrometer verification and small-part inspection. Presented as a single set, the components save time during setup and help standardise inspection routines across workstations. Lightweight and straightforward to handle, the kit streamlines frequent checks and supports efficient traceability within a calibration regime, helping to maintain production flow without complex procedures. Contact Metav Werkzeuge for application advice and prompt supply from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: M318.200.P GTIN: 4054469127965 Content: 6 gauge blocks and 1 flat glass Ø30 mm Material: Special steel, aged and hardened Standards: DIN 863; DIN EN ISO 3650/1 Weight: 0.57 kg Tariff number: 90173000 Numbers / Core technical data Pieces: 6 gauge blocks + 1 flat glass Ø30 mm Maximum reference size: 25.0 mm Set weight: 0.57 kg Special features Aged and hardened special steel construction Flat glass Ø30 mm included for flatness checks Designed for micrometer verification and workshop checks Compact set format for standardised calibration routines FAQ What standards does the gauge block set follow? The gauge block set M318.200.P is manufactured to meet DIN EN ISO 3650/1 and DIN 863, providing a clear standard reference for dimensional checks and micrometer verification. Can these blocks be used for daily micrometer checks? Yes, the six precision blocks and the Ø30 mm flat glass are designed for routine micrometer verification and frequent workshop inspection tasks. What material are the gauge blocks made from and how durable are they? The blocks are made from aged and hardened special steel, offering resistance to wear and stable reference dimensions for repeated use. Is the set suitable for traceable calibration procedures? The set’s standards compliance supports traceable verification procedures; for formal calibration certificates, please consult the supplier about available calibration services. What sizes are covered by the set? The kit provides reference sizes up to 25.0 mm with six precision blocks and the additional flat glass for complementary checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.1/10.3/15/20.2/25/50/75/100 End Gauge Set For Micrometers Grade 1 Hardened Special Steel In Case - Metav IndustryLine
The combination of Grade 1 accuracy, robust special steel construction and a practical span from 5.1 mm to 100 mm ensures reproducible reference measurements and efficient workshop checks. Order the set directly via Metav Werkzeuge or consult their experts for further assistance. M318.206 — Inspection gauge block set for micrometers, Grade 1 (5.1–100 mm) — Metav IndustryLine The M318.206 is an inspection gauge block set intended for verifying micrometer accuracy and routine dimensional checks across workshop and inspection environments. Grade 1 accuracy for reliable verifications Special hardened steel construction Conforms to DIN 863 and DIN EN ISO 3650/1 Sizes from 5.1 mm to 100 mm Consistent reference for micrometer verification A compact set of calibrated reference lengths provides a straightforward basis for checking micrometer performance. The blocks cover a useful dimensional range from 5.1 mm up to 100 mm, enabling quick spot checks and setting verifiable zero points on measuring instruments. Built to meet DIN 863 and DIN EN ISO 3650/1, the set supports reproducible comparisons and helps to reduce measurement-related rework by supplying stable reference values for routine verification tasks. Durable material and dimensional stability Manufactured from special steel, aged and hardened, the blocks resist wear and maintain surface integrity under frequent use. The material choice and heat treatment promote long-term dimensional stability, which is essential when a block serves as a workshop reference. At a total mass of 1.2 kg, the set is balanced for handling and storage while providing a feel of substance that reflects its intended precision role. Practical benefits for workshop and inspection workflows Using a concise set of reference lengths streamlines verification procedures: fewer changeovers, quicker instrument checks and predictable measurement outcomes. The blocks act as tangible calibration masters for micrometers and can be used alongside verification protocols to document instrument performance over time. This contributes to uptime, consistent part tolerances and a lower risk of rejects—advantages that translate into operational efficiency and measurable cost control for production and maintenance teams. Contact Metav Werkzeuge GmbH in Emmerich to request the M318.206 from Metav IndustryLine or to discuss application-specific recommendations — phone +49 2822 7131930, eMail info@metav-werkzeuge.com Technical data Article number: M318.206 GTIN: 4054469128061 TARIC / Customs code: 90173000 Facts Pieces per set: 8 Sizes: 5.1 mm; 10.3 mm; 15.0 mm; 20.2 mm; 25.0 mm; 50 mm; 75 mm; 100 mm Weight: 1.2 kg Grade: 1 Special features Material: special steel, aged and hardened Standards: DIN 863; DIN EN ISO 3650/1 Category: inspection gauge blocks / end standards FAQ What sizes are included in the set? The set contains blocks with the nominal lengths 5.1 mm, 10.3 mm, 15.0 mm, 20.2 mm, 25.0 mm, 50 mm, 75 mm and 100 mm as standard references. What level of accuracy does the set provide? This is a Grade 1 inspection set manufactured to the requirements of DIN 863 and DIN EN ISO 3650/1, intended for reliable workshop verification. What material are the gauge blocks made from? The blocks are produced from a special steel, aged and hardened to ensure wear resistance and dimensional stability under repeated use. Can these blocks be used to check micrometers? Yes, the set is specifically described as an inspection gauge block set for micrometers and is suitable for verifying micrometer accuracy across the included range. Is a calibration certificate supplied with the set? The product information does not state that a calibration certificate is included with the M318.206 Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.1mm Gauge Block For Micrometer Calibration DIN EN ISO 3650/1, Special Steel - Metav IndustryLine
Take advantage of DIN EN ISO 3650/1 conformity, a 5.1 mm nominal diameter and robust special steel construction for repeatable micrometer verification; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. End gauge for testing micrometers, 5.1 mm — Metav IndustryLine The End gauge for testing micrometers, 5.1 mm serves as a compact precision reference for routine verification of micrometers in workshop and calibration environments. DIN EN ISO 3650/1 compliant accuracy Nominal diameter 5.1 mm Made from hardened special steel Compact, portable reference gauge Precision that assures dependable micrometer checks The reference instrument is manufactured to DIN EN ISO 3650/1, offering a clear normative basis for repeatable verification of micrometer readings. With a 5.1 mm nominal diameter, the gauge provides a stable reference point for the inspection of external micrometer jaws. Built as a dedicated test standard, it reduces uncertainty in comparative checks and streamlines decision-making in quality control processes. The result is a reliable baseline for calibration cycles and acceptance testing. Durable construction for everyday workshop use Constructed from special steel and finished for long-term stability, the gauge resists typical workshop wear while maintaining dimensional integrity. At approximately 0.3 kg, the component is compact and convenient to handle during inspection routines, yet substantial enough to avoid damage through mishandling. The material choice and manufacturing tolerance combine to ensure consistent contact conditions when comparing a micrometer spindle to the reference gauge, supporting fast, repeatable measurements without frequent reconditioning. Integration into inspection workflows and documentation This gauge is suited for use in production monitoring, incoming inspection and periodic verification in small to medium-sized workshops as well as calibration benches. When incorporated into a documented test procedure, the device helps to demonstrate traceable verification steps and supports quality records. The compact form factor makes it simple to store alongside inspection tools or include within a calibration kit, facilitating systematic checks and easing operator training for routine metrological tasks. Contact Metav Werkzeuge for procurement and technical guidance on M318.203.1 — our specialists in Emmerich can advise on documentation, delivery and integration into your inspection processes Technical data Article number: M318.203.1 GTIN: 4054469178394 Label: End gauge for testing micrometers, 5.1 mm DIN EN ISO 3650/1 Facts Nominal diameter: 5.1 mm Weight: 0.3 kg Customs tariff number: 90173000 Special features Standard: DIN EN ISO 3650/1 Material: Special steel Category: End gauge SKU: M318.203.1 FAQ What is the primary use of this gauge? The gauge is designed as an end reference for verifying the accuracy of external micrometers; M318.203.1 is intended for routine comparative checks and calibration procedures. Does the gauge comply with recognised standards? Yes, the device is manufactured to DIN EN ISO 3650/1, providing a normative framework suitable for documented verification workflows. Which material is used for the gauge and why does it matter? Made from special steel, the gauge offers dimensional stability and wear resistance that preserve contact conditions during repeated use and thus sustain reliable micrometer checks. Can this gauge be used in production quality control? The compact reference gauge integrates easily into production and incoming inspection routines, helping to maintain traceable verification records and consistent measurement practice. Is the product suitable for portable calibration kits? Owing to its compact size and robust construction, M318.203.1 is suitable for inclusion in portable calibration or inspection kits used on the shop floor. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.1–25mm Gauge Block Set Class 1, 5 Pieces - TECWERK
Benefit from tolerance class 1 accuracy, a compact five‑piece composition and sturdy steel construction for reliable inspection references; order the set directly via Metav Werkzeuge or consult the in‑house specialists if further technical clarification is required. TECWERK Parallel end gauge set — tolerance class 1, 5‑piece steel The Parallel end gauge set is a precision reference kit for dimensional verification, intended for workshop inspection, assembly and calibration tasks Tolerance class 1 accuracy Hardened steel construction Set of five calibrated sizes Compact reference for inspection tasks Faster, verifiable results through certified tolerance The selection of components in this steel gauge set is optimised to reduce iteration during inspection. With tolerance class 1 the components provide a defined limit of conformity that can be relied on for pass/fail checks and quick reference measurements. The calibrated increments eliminate guesswork when establishing reference distances; the result is fewer adjustments on the production line and a measurable reduction in inspection time. This level of reproducibility supports process stability and clearer documentation for quality records. Durable material and stable geometry for routine use Manufactured in steel, the set offers consistent dimensional stability under normal workshop conditions. The choice of material ensures wear resistance and long service life when stored and handled appropriately. Clear flat contact faces maintain parallelism and make the set suitable as a bench reference for height and gap checks. Regular cleaning and dry storage preserve the calibration state and extend the interval between checks, translating into lower life‑cycle costs and dependable day‑to‑day performance. Practical composition and typical applications explained The set comprises five calibrated elements that cover common reference steps used in inspection and assembly tasks: 5.1 mm, 10.3 mm, 15 mm, 20.2 mm and 25 mm. By combining elements, users can create intermediate distances can be created quickly, offering flexibility for routine measurement tasks without complex fixturing. The compact kit functions well as a visual and tactile reference in incoming inspection, final checks and set‑up verification. If detailed calibration data or compatibility information is required, technical enquiries are welcome to ensure fit for purpose. Contact Metav Werkzeuge for tailored supply from Emmerich or for detailed technical advice on this TECWERK parallel end gauge set Technical Data Article number: 2000851635NW Designation: Parallel end gauge set Tol.-Kl.1 5tlg. STA TECWERK SKU: 2000851635NW Brand: TECWERK Packaging unit: 1 Specifications Tolerance class: 1 Set composition: 1 × 5.1 mm / 1 × 10.3 mm / 1 × 15 mm / 1 × 20.2 mm / 1 × 25 mm Number of pieces: 5 Materials & Features Material: steel (STA) Product type: Parallel end gauge set Compact calibrated increments Intended for inspection and reference use FAQ What degree of accuracy does the set provide? The TECWERK parallel end gauge set is specified to tolerance class 1, providing a reliable reference level for workshop inspection and comparative checks. Which sizes are included in the kit? The set contains five elements: 5.1 mm, 10.3 mm, 15 mm, 20.2 mm and 25 mm, enabling combined configurations for intermediate distances. Is the set suitable as a calibration reference on the shop floor? Yes; the steel construction and calibrated increments make the set suitable for routine bench references and quick verification tasks in production and inspection areas. How should the elements be maintained to preserve accuracy? Handle the elements with clean hands or gloves, remove debris before use, and store dry. Periodic calibration checks are recommended to confirm continued conformity. Can the set be used for precise set‑up and assembly alignment? The compact, calibrated steps are suitable for set‑up and alignment applications where defined reference distances are required; the kit assists in repeatable positioning and inspection. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
5.5 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of ceramic material, Grade 1 accuracy and compact 5.5 mm nominal size for consistently reproducible reference measurements; order the ceramic gauge block directly via Metav Werkzeuge or consult our specialists for procurement advice. Ceramic gauge block 5.5 mm — Grade 1 (DIN 861/1) by Metav IndustryLine The ceramic gauge block 5.5 mm (Grade 1, DIN 861/1) is a compact precision reference designed for dimensional verification and setting tasks in workshops and calibration benches. Grade 1 accuracy to DIN 861/1 Low thermal expansion ceramic Compact 5.5 mm nominal size Reliable metrology for repeatable measurement results The Grade 1 designation according to DIN 861/1 guarantees a defined tolerance band that makes this gauge block an appropriate choice for routine reference tasks where measurement certainty matters. As a small-format reference, the 5.5 mm nominal dimension offers precise step-setting capabilities and convenient integration into existing gauge sets. The manufacturing grade ensures that deviations remain within the expected limits for Grade 1 standards, supporting consistent process control and reducing time spent on rework or adjustment. Ceramic material benefits for stable references Manufactured from ceramic, the block delivers dimensional stability and wear resistance that outperform many metallic counterparts in daily use. The low thermal expansion of the ceramic substrate reduces temperature-induced drift during short-term handling and ambient changes, so measurements remain reliable without elaborate climate control. Ceramic also resists corrosion and is electrically non-conductive, which simplifies storage and handling in mixed-material environments while preserving the measuring faces for extended service life. Practical handling and integration into workshop routines The compact nominal size and lightweight construction (approx. 0.01 kg) make the block easy to position for comparison, instrument set-up or calibration tasks. As a small precision reference standard, it is suitable for setting micrometres, checking caliper zero points and assembling gauge stacks. Careful handling and clean wringing practices preserve surface quality and ensure reproducibility. For procurement and traceable supply, this block is available from Metav IndustryLine and fits directly into standard gauge assortments used in quality departments and production support. For procurement and technical advice on the Metav IndustryLine ceramic gauge block 5.5 mm (SKU M324.005.5), contact Metav Werkzeuge directly by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — our team in Emmerich can advise on delivery and compatibility with existing reference sets Technical data Article number: M324.005.5 GTIN: 4054469142999 Customs tariff number: 90173000 Category: Endmasse Facts Nominal size: 5.5 mm Weight: 0.01 kg Grade: 1 Special features Material: Ceramic Standard: DIN 861/1 Brand: Metav IndustryLine FAQ What accuracy class does this ceramic gauge block meet? The ceramic gauge block meets Grade 1 accuracy according to DIN 861/1, providing a defined tolerance suitable for routine reference measurements with the Metav IndustryLine M324.005.5. Is the ceramic block suitable for use in a standard gauge set? Yes. The 5.5 mm nominal size is compatible with standard gauge stacks and can be integrated into existing sets for setting micrometres, calipers and comparators. How should the gauge block be handled to preserve its measuring faces? Handle the Metav IndustryLine ceramic gauge block with clean, lint‑free gloves or tweezers, avoid impact, and store it in a dry, dust‑free container to maintain surface quality and repeatability. Can the block be used for contact measurements at elevated temperatures? Ceramic offers low thermal expansion compared with many metals, improving short‑term thermal stability; however, high‑precision measurements should always consider ambient and contact temperature control for best results. What information identifies the product for ordering or inventory? Order using SKU M324.005.5 or GTIN 4054469142999 to ensure the correct Metav IndustryLine ceramic gauge block is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.5 mm Gauge Block Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of the combination of high repeatability, hardened special-steel construction and adherence to DIN EN ISO 3650 for reliable length standards; order the gauge block directly via Metav Werkzeuge or request guidance from our consultants for integration into inspection routines. Gauge block 5.5 mm — Grade 1 length standard, DIN EN ISO 3650 The gauge block 5.5 mm is a precision length standard designed for dimensional verification and setting tasks in workshops and inspection benches, compliant with DIN EN ISO 3650 and intended for routine metrological use. Gauge block 5.5 mm nominal length Grade 1 tolerance to DIN EN ISO 3650 Hardened special steel construction Compact cross-section 30 × 9 mm Precision that keeps production on spec Manufactured to Grade 1 tolerances under DIN EN ISO 3650, this small length standard gives a dependable reference for calibration chains and comparative measurements. The specified 5.5 mm nominal length and careful finishing reduce measurement uncertainty at the reference stage, which in turn lowers the risk of rework and out-of-tolerance production. The graded accuracy supports repeatable results across routine checks and gauge setting, improving throughput by limiting doubt in pass/fail decisions while maintaining traceable documentation for quality systems. Compact design for everyday metrology A compact cross-section and low mass make the block easy to handle during frequent checks: the applicable cross-section for this nominal range is 30 × 9 mm, and the component mass is approximately 0.009 kg. Those physical characteristics mean fewer errors from leverage or operator-induced bending when compared with longer or heavier standards, so bench-based measurement remains straightforward. The small footprint also simplifies storage in gauge sets and reduces the space required in inspection cupboards, helping maintain an organised measurement workplace. Made to last and support quality systems Constructed from hardened special steel, the block is intended to offer wear resistance and dimensional stability under normal workshop conditions, supporting long service life and consistent calibration intervals. Robust material choice directly translates into lower lifecycle cost because durable standards maintain form and permit longer intervals between corrective regrinding or replacement. In applications where reproducibility is critical—setting plug gauges, verifying micrometre zero settings or supporting master comparisons—this grade and construction provide an economical balance of precision and resilience. For traceable, workshop-ready length standards and assistance integrating Grade 1 references into existing inspection routines, contact Metav Werkzeuge for ordering and technical advice from their Emmerich team. Technical data Article number: M319.055.1 GTIN: 4054469131399 Category: Gauge blocks Norm: DIN EN ISO 3650 Material: Special steel, hardened Numbers / Core technical data Nominal length: 5.5 mm Weight: 0.009 kg Cross-section: 30 × 9 mm Tolerance grade: 1 Tariff number: 90173000 Special features Hardened special-steel construction Conforms to DIN EN ISO 3650 Suitable for workshop and inspection use FAQ What tolerance class does this gauge block meet? The gauge block meets Grade 1 tolerances in accordance with DIN EN ISO 3650, offering a level of accuracy suitable for workshop inspection and comparative measurements. Which material is used and how does it affect service life? Made from hardened special steel, the block provides increased wear resistance and dimensional stability compared with softer materials, which helps to extend service life under normal handling and reduces frequency of maintenance. Is the block suitable for setting micrometres and gauges? Yes; the 5.5 mm reference is appropriate for setting micrometres, checking gauge blocks and supporting everyday calibrations where a compact, accurate standard is required. How should the gauge block be stored and handled? Store the block dry and free from abrasive contaminants; keep it within a protective gauge set or wrap when not in use to preserve surface condition and accuracy. What are the article and identification details for ordering? Article: M319.055.1; nominal length 5.5 mm; GTIN 4054469131399; category Gauge blocks Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.5 mm Gauge Block Single End, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of proven interchangeability and traceable tolerance with a compact Grade 0 reference element; the hardened special steel construction ensures long-term stability while the precise 5.5 mm nominal size integrates cleanly into gauge stacks and calibration setups. Order directly via Metav Werkzeuge or contact the consultants for technical advice. Metav IndustryLine single gauge block 5.5 mm — Grade 0, DIN EN ISO 3650 The single gauge block 5.5 mm (DIN EN ISO 3650, Grade 0) is a compact reference length for high-precision setting, calibration and verification tasks in dimensional metrology Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel construction Compact 5.5 mm reference length Suitable for calibration and gauge stacks Precision where conformity matters The Grade 0 tolerance class defined in DIN EN ISO 3650 provides a reliable basis for traceable length standards in workshop and laboratory environments. As a single reference element with a 5.5 mm nominal size, this gauge is manufactured for minimal geometric deviation and consistent interchangeability. The normative specification means inspection results and instrument settings can be compared across sites and shifts without ambiguity, supporting quality control procedures and process documentation. Durable material and stable handling Constructed from hardened special steel, the gauge block resists wear during repeated use and stacking, so calibration intervals remain predictable and working tolerances are maintained. The compact form contributes to repeatability when building gauge stacks or setting micrometers, while the low mass of the element allows safe, ergonomic handling. These material and design choices reduce the risk of surface damage and extend the service life of the reference, translating into fewer replacements and steadier measurement routines. Practical application and integration in quality workflows In practice, the block acts as a precise reference for setting measuring instruments, checking micrometre calibration and assembling gauge stacks for workshop checks. The standardised dimensions and conformity to DIN EN ISO 3650 simplify documentation in inspection protocols and support process audits. Supplied as a single element, the item is ideal where a small, accurate reference length is required for spot verification or as part of a larger set of calibrated standards. Choose the Metav IndustryLine Grade 0 single gauge block for consistent reference measurements and contact Metav Werkzeuge GmbH in Emmerich for expert guidance and supply coordination Technical data Article number: M319.055.0 GTIN: 4054469131382 Customs tariff: 90173000 Facts Nominal size: 5.5 mm Weight: 0.008 kg Tolerance grade: 0 (Grade 0) Standard: DIN EN ISO 3650 Special features Material: Special steel, hardened Cross-section: bis 10mm 30x9mm, ab 10,1mm 35x9mm Category: Endmasse (gauge blocks) Manufacturer: Metav IndustryLine FAQ What level of accuracy does this gauge block provide? The gauge block is manufactured to Grade 0 tolerances according to DIN EN ISO 3650, providing the conformity required for many workshop and laboratory calibration tasks. Can this block be used in gauge stacks for setting instruments? Yes, the 5.5 mm element is intended for integration into gauge stacks and for direct instrument setting; the hardened special steel construction supports repeated stacking and handling. Is the material suitable for routine workshop use? The hardened special steel offers wear resistance and stability suitable for routine calibration work and frequent use in production environments. Which applications are typical for a 5.5 mm single gauge block? Typical uses include micrometre setting, checking dead-length standards, spot verification of measuring instruments and forming parts of a broader set of reference standards. How is the product identified for ordering or inventory? The product is listed as Metav IndustryLine single gauge block, SKU M319.055.0, GTIN 4054469131382 Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of standardised Grade 1 accuracy, a stable ceramic reference surface and the compact 50 mm nominal length for repeatable length checks; order the gauge block directly via Metav Werkzeuge or consult our specialists for specification matching. Ceramic Gauge Block 50 mm — Grade 1 (DIN 861/1) by Metav IndustryLine The Ceramic Gauge Block 50 mm is a compact, standardised length reference intended for metrology, calibration and precision inspection tasks where a Grade 1 tolerance is required. Ceramic material for dimensional stability Grade 1 accuracy per DIN 861/1 50 mm nominal reference length Precision where it matters: standardised Grade 1 reference This compact reference is specified as Grade 1 according to DIN 861/1, offering a clear standard for tolerance and interchangeability in workshop and inspection settings. The 50 mm nominal length provides a frequently required reference size for calibration chains and comparator setups, supporting routine checks and master-set assemblies. By using a standardised gauge, organisations maintain traceable measurement baselines that simplify quality control and ensure comparability across instruments. Material and handling: what the ceramic construction provides Made from ceramic, the block delivers a stable reference surface with durable dimensional properties appropriate for repeated comparative measurements. The material choice is reflected in the design and intended use as a length standard; the compact form factor and modest mass (0.095 kg) ease handling and positioning during inspection sequences. The block is suitable for incorporation into reference sets and for use in laboratory or shop-floor micrometrology tasks where a robust, non-metallic reference is preferred. Practical use and integration into workflows As a standardised length artefact, this gauge block is intended for direct inclusion in calibration procedures, reference stacks or as a master for comparative measurement. Its GTIN and SKU simplify inventory and traceability within equipment management systems, and the DIN conformity aids specification compliance for quality audits. Metav’s positioning as a precision partner in Emmerich underpins supply reliability and supports procurement of complementary metrology items to assemble complete reference kits. Contact Metav Werkzeuge now to confirm suitability for existing calibration rigs and to secure the Metav IndustryLine Ceramic Gauge Block 50 mm from stock in Emmerich, or request further specification details by email or phone Technical data Article number: M324.050 GTIN: 4054469143415 Material: Ceramic Nominal length: 50 mm Accuracy grade: Grade 1 (DIN 861/1) Net weight: 0.095 kg Tariff number: 90173000 Facts Length: 50 mm Weight: 0.095 kg Grade: 1 GTIN: 4054469143415 Special features Category: Gauge blocks (Endmasse) SKU: M324.050 Material: Ceramic Brand line: Metav IndustryLine FAQ What nominal size does this gauge block have? The Ceramic Gauge Block 50 mm (Metav IndustryLine, SKU M324.050) provides a nominal length of 50 mm for use as a reference standard. What accuracy specification applies to this block? This gauge block is specified as Grade 1 according to DIN 861/1, offering a defined industrial tolerance class for length reference work. What is the block made from and how does that affect use? The block is made from ceramic; the Ceramic Gauge Block 50 mm is intended as a stable, durable reference suitable for repeated comparative measurements in metrology applications. Is a calibration certificate included with the product? The product data lists the block as Grade 1 (DIN 861/1); the presence of a calibration certificate is not indicated in the provided information Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50 mm End Gauge Holder Very Sturdy Design - Metav IndustryLine
Benefit from a combination of robust construction, a precise 0–50 mm clamping range and compact handling for dependable, repeatable gauge work; order directly via Metav Werkzeuge or contact our consultants for application advice. End gauge holder 50 mm clamping range 0–50 mm — robust end measure holder by Metav IndustryLine The End gauge holder 50 mm clamping range 0–50 mm secures gauge blocks and end measures for precise length setting and routine calibration tasks in workshop and inspection environments. Very stable, heavy‑duty construction 0–50 mm adjustable clamping range Designed for secure gauge block mounting Compact design, approx. 0.4 kg weight Repeatable clamping for precise, routine calibration The holder’s robust construction and controlled clamping geometry provide a stable contact interface that minimises movement and distortion during handling. A defined clamping range 0–50 mm ensures that end measures and gauge blocks are held square and true, which directly reduces setup variance and supports repeatable calibration outcomes. This results in fewer retakes during inspection runs and a measurable improvement in throughput for repetitive length checks. Workshop‑ready design that speeds handling Engineered for everyday use, the device combines heavy‑duty materials with a compact footprint to make placement, alignment and removal of gauge stacks straightforward. At approximately 0.4 kg, the holder is easy to manoeuvre while remaining sufficiently massed to resist minor knocks and vibration. The simple, approachable form reduces handling time during routine checks and contributes to a more consistent measurement routine across operators. Fits calibration workflows and standard gauge sets Designed to accept standard end measures and gauge block stacks, the holder integrates seamlessly into established calibration procedures and inspection benches. Secure mounting minimises relative movement between references and test pieces, improving measurement confidence and traceability of results. The device supports efficient workflows in small batch quality control, toolroom calibration and production sampling. Built quality and supplier assurance for reliable procurement Manufactured under the Metav IndustryLine umbrella, the holder reflects Metav’s practical focus on dependable metrology tools for workshops and inspection labs. The solid mechanical design prioritises lifespan and repeatability, reducing the need for frequent replacements and helping to ensure consistent measurement practice across teams. For applications requiring documentation or batch procurement, Metav Werkzeuge provides direct supply and advisory support from its Emmerich facility. For robust, repeatable calibration in the workshop, contact Metav Werkzeuge to discuss the Metav IndustryLine end gauge holder (SKU M317.203) and confirm compatibility with existing gauge sets at info@metav-werkzeuge.com or by phone at +49 2822 7131930. Technical Data Article number: M317.203 GTIN: 4054469127491 Eclass: 21170108 Tariff number: 90173000 Label: Endmaßhalter 50 mm Spannbereich 0 - 50 mm Description: End gauge holder Facts Clamping range: 0–50 mm Weight: 0.4 kg Cross-section: bis 300mm 30x5mm und ab 300mm 30x6,7mm Category path: Messgeräte > Endmasse Special features Very stable execution (sehr stabile Ausführung) Suitable for gauge block and end measure mounting Compact, workshop-friendly footprint FAQ What is the clamping range of the holder? The holder provides an adjustable 0–50 mm clamping range suitable for most small gauge block stacks and end measures. Is the device suitable for routine calibration work? Yes, the Metav IndustryLine end gauge holder (SKU M317.203) is designed for repeatable mounting of end measures and assists in routine calibration and inspection tasks. How heavy is the holder and how does that affect handling? The device weighs approximately 0.4 kg, offering a balance between portability and sufficient mass to resist minor disturbances during measurements. Can the holder be used with standard gauge block sets? The holder is intended for secure gauge block mounting and integrates with standard end measures used in workshop calibration routines. Who supplies this holder and where can advice be obtained? The holder is supplied under Metav IndustryLine; procurement and technical advice are available from Metav Werkzeuge in Emmerich. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50 mm End Gauge Holder Very Sturdy Design, 0–50 mm Range - Metav IndustryLine
The combination of very stable construction and a precise 0–50 mm clamping range ensures reproducible results for gauge and end-measure work; the compact cross-section and low mass keep handling straightforward while maintaining accuracy. Order the gauge block holder directly via Metav Werkzeuge or consult our specialists for application advice. Gauge block holder 50 mm — 0–50 mm clamping range, Metav IndustryLine A gauge block holder 50 mm designed to secure end measures during calibration and precision measurement tasks in metrology laboratories and workshop environments. Very stable construction for reproducible clamping Clamping range 0–50 mm for standard gauge work Compact cross-section 30.5 x 2.5 mm for precise fit Lightweight 0.4 kg for easy handling in the lab Consistent clamping for repeatable measurements The robust design delivers reproducible positioning of end measures, making it a reliable fixture for routine calibration and inspection procedures. With a defined 0–50 mm clamping range, the unit supports standard gauge blocks and end measures used across inspection benches and calibration rigs. The compact profile minimises play at the contact points, which helps to reduce measurement uncertainty and supports consistent results during serial checks or single‑part verifications. Smooth integration into workshop and laboratory workflows Engineered for straightforward handling, the holder’s modest mass and narrow cross-section ease alignment and placement in tight setups. Its lightweight nature (approx. 0.4 kg) reduces operator fatigue during repeated use and speeds up cycle times in quality control processes. As a consequence, throughput improves without compromising the precision required for certification or acceptance testing, delivering efficiency gains that support both small workshops and larger metrology departments. Durable build that supports long-term inspection routines Constructed for enduring service, the fixture withstands regular handling while maintaining the geometric stability necessary for traceable measurement work. The very stable construction reduces the need for frequent realignment and contributes to a lower total cost of ownership through fewer process interruptions. Compatibility with standard end measures ensures straightforward integration into existing gauge sets, simplifying inventory and tooling decisions for procurement and workshop managers. For dependable gauge work choose the Metav IndustryLine holder and contact Metav Werkzeuge in Emmerich for tailored advice or to arrange supply Technical data Article number: M317.103 SKU: M317.103 GTIN: 4054469127330 Category: Endmasse (gauge blocks) eClass: 21170108 Facts Clamping range: 0–50 mm Cross-section: 30.5 x 2.5 mm Weight: 0.4 kg Tariff number: 90173000 Special features Very stable construction Suitable for use with end measures and gauge blocks Compact design for tight setups Story trigger: endmasse FAQ What clamping range does the holder cover? The gauge block holder 50 mm (Metav IndustryLine, SKU M317.103) covers a clamping range of 0–50 mm, suitable for standard end-measure tasks. Is this holder suitable for calibration workflows? Yes. The holder’s stable design and precise clamping make it well suited for calibration and repeatable inspection routines using gauge blocks and end measures. How heavy is the unit and how does that affect handling? Weighing approximately 0.4 kg, the holder is lightweight enough for easy alignment and frequent handling while remaining rigid enough for stable measurements. Which profile dimensions aid precise fitting in setups? The compact 30.5 x 2.5 mm cross-section allows secure placement in narrow fixtures and helps to maintain consistent contact geometry during measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
ensure traceable length calibration with gauge blocks
gauge blocks, also called slip gauges or end gauges, are precision length standards designed to transfer exact measures during calibration and setup. Manufactured and graded for metrological use, they provide the reference dimensions needed to verify and adjust measuring instruments in industrial workshops and calibration labs.
how gauge blocks work and where they are essential
gauge blocks are used to create known lengths by wringing individual blocks together or by using a single block as a reference. length calibration in industry commonly relies on parallel gauge blocks, while angle, cylinder and sphere end gauges serve specialised tasks. these blocks are produced in steel, ceramic or carbide, and their material choice balances wear resistance with thermal behaviour. regular calibration—typically performed annually—by DAkkS-accredited laboratories ensures traceability. the highest-precision reference work, class K, is certified by the PTB using laser techniques; classes 0, 1 and 2 are tested under progressively less controlled conditions (class 0 in a climate-controlled lab, class 1 in a standard measurement room, class 2 in production).
measurable benefits that cut downtime and uncertainty
- consistent, traceable length standards reduce rework and measurement disputes by enabling reliable instrument calibration.
- choosing the correct material (steel, ceramic, carbide) extends service life and limits wear in high-use environments.
- selecting the right accuracy class (K, 0, 1 or 2) matches calibration effort to application needs and avoids over‑specification.
- annual calibration by accredited labs maintains documented compliance and supports quality systems such as ISO.
why Metav is a smart partner for precision standards
Metav combines specialist knowledge with a broad range of measurement technology, making the procurement of gauge blocks straightforward and dependable. with over 48,000 customers and more than 250,000 products stocked from Emmerich, Metav acts as a pragmatic quality filter for European workshops, reducing supplier complexity and ensuring consistent supply.
In short, gauge blocks deliver traceable, material‑appropriate and class‑matched references that keep calibration workflows efficient and auditable.
faq
what materials are gauge blocks available in and why does it matter?
gauge blocks are typically supplied in steel, ceramic or carbide. material choice affects wear resistance, stability and thermal expansion; selecting the right material for your environment optimises longevity and measurement stability.
how often should gauge blocks be calibrated?
industry practice is an annual calibration cycle, carried out by DAkkS-accredited laboratories, though frequency can be increased depending on usage and required uncertainty.
what do the accuracy classes k, 0, 1 and 2 indicate?
the classes denote graded tolerances and test conditions: K is the highest precision (certified by PTB with laser measurement), class 0 is checked under climate-controlled lab conditions, class 1 in a normal measurement room and class 2 in production environments.
are parallel gauge blocks always used for length calibration?
yes; for length calibration the parallel gauge blocks are the primary standard because they provide exact planar faces for wringing and stacking to create precise lengths.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com