End gauges for precise length calibration
End gauges provide exact reference lengths for calibrating measurement instruments and ensuring consistent dimensional accuracy in metalworking and inspection processes. Used in production and laboratory settings, these end gauges—made from steel, ceramic or carbide—allow technicians to compensate for wear and thermal effects and maintain measurement traceability, especially when employed alongside parallel end gauges, cylinder gauges and calibration masters. Classes 0, 1 and 2 define practical tolerance levels for workshop, inspection-room and production use respectively, delivering the repeatable precision required for machining and quality control.
70mm Jaw R10x20 For Gauge Holder 9x10.5 Slot Set - Metav IndustryLine
Take advantage of precise R10 contact geometry, a compact 70 x 9 x 10.5 mm shank and the convenience of a set of two jaws for mirrored measuring tasks — a combination that supports repeatable results and simple retrofitting into common measuring fixtures. Order the accessory directly via Metav Werkzeuge or consult our specialists if required. Measuring Jaw R10 x 20 mm — 70 x 9 x 10.5 mm shank (Metav IndustryLine) A Measuring Jaw R10 x 20 mm designed as an accessory for precision measuring equipment and gauge fixtures, offering repeatable contact geometry for workshop and inspection use Precision R10 profile for repeatable contact Shank 70 x 9 x 10.5 mm for secure mounting Supplied as a set of 2 for left/right configurations Compatible with standard gauge holders Consistent contact geometry that improves repeatability The R10 tip profile provides a defined contact radius that reduces variability at the measuring interface, converting a complex contact condition into a repeatable reference. By using a controlled tip form rather than a blunt or undefined edge, the jaws generate more consistent seating on cylindrical or radiused features; this leads to repeatable measurement results and fewer re-measurements. The design is particularly useful in series inspection where the same contact condition must be reproduced across multiple parts. Secure installation and immediate retrofit into fixtures With a shank measuring 70 x 9 x 10.5 mm, the jaws are shaped to locate positively in standard accessory holders and gauge fixtures. The compact mounting dimensions make replacement and retrofit straightforward: the component can be fitted quickly without modification to the carrier, which minimises downtime and supports fast tool changes. Supplied as a set of 2, the pair allows mirrored mounting or simultaneous use for internal and external reference configurations. Low mass and compact form for delicate measurement tasks At approximately 0.01 kg per set member, the low mass reduces inertia on moving slides and helps preserve instrument dynamics during light-touch measurements. The compact cross-section ensures the jaws remain stiff over their short working length while keeping obstruction to the workpiece to a minimum. For applications where fine positioning and minimal probe force are important, the small footprint supports careful handling and precise alignment. Practical benefits in daily inspection and metrology tasks As a measuring accessory, the jaw set supports efficient workshop workflows by simplifying fixture setup and reducing variation between operators. The engineered contact profile cuts setup time by providing a reliable seating point, while the standardised shank dimensions ensure broad compatibility with gaugeholders and other metrology fixtures. For inspection environments that prioritise traceability and consistent measurement chains, the component forms a practical element in a quality-controlled process. For retrofit, spares or project procurement of Metav IndustryLine measuring jaws, contact Metav Werkzeuge for tailored advice and ordering: email info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will ensure the correct configuration for the intended fixture or inspection task. Technical data Article number: M317.108 GTIN: 4054469127385 Manufacturer brand: Metav IndustryLine Shank dimensions: 70 x 9 x 10.5 mm Measuring tip: R10 x 20 mm Length: 70 mm Weight: 0.01 kg Tariff number: 90173000 Pieces per set: 2 Supplied as a set of two jaws Intended use: accessory for measuring instruments and gauge fixtures Cross-section: 9 x 10.5 mm Category: Accessories (measuring devices) FAQ Are these jaws compatible with standard gauge holders? The jaws feature a 70 x 9 x 10.5 mm shank and are designed for compatibility with common gauge holders and accessory carriers; verify the holder groove dimensions to ensure a positive fit. What measuring profile do the jaws offer and why does it matter? The R10 x 20 mm contact radius gives a defined seating geometry that improves repeatability and reduces measurement scatter compared with undefined edges. Is the product supplied as a single item or a set? The item is supplied as a set of 2 pieces, which supports mirrored mounting or paired use in inspection setups. Can these jaws be used for internal and external measurements? The geometry and compact size permit use in a variety of tasks; adaptation for internal or external reference depending on holder orientation is straightforward. What is the product SKU for ordering or referencing? The product is listed as SKU M317.108 for Metav IndustryLine. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
70x60x8 mm Holder for Gauge Block Holder Very Sturdy For Horizontal Use - Metav IndustryLine
Benefit from the combination of very stable construction, a compact 70 × 60 × 8 mm footprint and dedicated anti‑tilt support for reliable horizontal calibration results — order the holder directly via Metav Werkzeuge or ask our consultants if needed Holder for end gauge support M317.213 — horizontal mounting, very stable construction (Metav IndustryLine) The Holder for end gauge support M317.213 is a compact bracket designed to prevent lateral tipping during horizontal calibration and measurement setups for end gauges Very stable heavy-duty construction Horizontal mounting prevents lateral tipping Compact 70 × 60 × 8 mm footprint Consistent calibration through stable support A mechanically robust support reduces variability during bench calibration and repeat measurements. The bracket’s very stable construction and anti‑tilt design keep the gauge datum aligned under horizontal mounting conditions, which directly improves precision and repeatability in routine checks. Where measurement drift is costly, this support secures the end gauge so that comparative readings remain consistent and reproducible between successive calibrations, helping to maintain quality control documentation. Small footprint with workshop resilience The compact 70 × 60 × 8 mm dimensions combine a minimal footprint with a design that resists flexing under typical workshop loads. The unit’s modest weight makes handling straightforward while its construction prioritises profile stiffness to avoid unwanted movement; this leads to fewer setup iterations and faster throughput on the calibration table. The result is a space‑saving accessory that supports more reliable results without occupying valuable bench area. Designed to fit common gauge configurations Intended for use with end gauges and similar reference standards, the support accepts common cross‑section profiles: 30 × 5 mm for parts up to 300 mm and 30 × 6.7 mm for longer sections. This compatibility enables straightforward integration into established measurement routines and simplifies fixture planning for both bench and light production environments. The anti‑tilt feature is particularly useful when gauges are used in a horizontal orientation for comparative or verification tasks. Practical workshop benefits and supplier confidence The support reduces handling‑related errors and shortens setup time, which together raise productive measurement capacity on the shop floor. Sourcing from Metav IndustryLine brings the advantage of a focused supply channel: reliable availability and a quality filter based in Emmerich that supports consistent standards. The compact bracket is therefore a practical, low‑risk addition to calibration kits and inspection benches seeking improved stability for horizontal measurements. For robust horizontal end‑gauge support and application advice, contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com to discuss the M317.213 and its suitability for specific measurement setups Technical data Article number: M317.213 GTIN: 4054469158211 Eclass: 21170108 Tariff number: 90173000 Facts Dimensions: 70 x 60 x 8 mm Weight: 0.4 kg Cross‑section up to 300 mm: 30 x 5 mm Cross‑section from 300 mm: 30 x 6.7 mm Special features Very stable construction For horizontal mounting Prevents lateral tipping Category: Endmasse FAQ What is the primary purpose of this holder? The holder secures end gauges in a horizontal orientation to prevent lateral tipping and to support repeatable calibration and comparative measurements with the M317.213. Which cross‑sections does the support accept? The support is compatible with 30 × 5 mm profiles for components up to 300 mm and 30 × 6.7 mm profiles for longer items, matching typical gauge block and end‑gauge formats. Is the bracket suitable for bench calibration of end gauges? Yes, the bracket is intended for bench calibration use; its very stable construction reduces measurement scatter during horizontal setups. Does the support require additional fixtures to hold standard end gauges? In most cases the bracket functions as a direct support for standard end‑gauge profiles; specific fixture requirements depend on the gauge geometry and measurement procedure. How does the holder improve measurement workflow? By preventing tilt and improving datum stability, the holder shortens setup time and reduces repeat measurements, contributing to more efficient inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of a ceramic reference that pairs Grade 1 accuracy with low thermal expansion and a compact 75 mm nominal length for reliable workshop and calibration use; order directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic gauge block 75 mm, Grade 1 DIN 861/1 — Metav IndustryLine Ceramic gauge block 75 mm, Grade 1 DIN 861/1 offers a stable length standard for calibration benches and precision inspection in metalworking and metrology environments Grade 1 accuracy to DIN 861/1 Thermally stable ceramic construction Compact 75 mm nominal length Consistent reference value for routine and lab checks The Grade 1 classification according to DIN 861/1 ensures a reproducible tolerance class suitable for many workshop and inspection tasks. Made from ceramic, the block provides a thermal stability advantage over many metallic gauges: the low coefficient of thermal expansion reduces length variation with temperature shifts, improving repeatability on the shop floor and in controlled calibration rooms. As a compact reference standard, the block supports routine verification and comparative checks without demanding extensive handling protocols. Practical use for calibration and inspection workflows With a nominal length of 75 mm, this gauge block fills a common measuring need between bench standards and smaller reference pieces. The non‑metallic composition offers wear resistance and non‑magnetic behaviour, which helps avoid magnetic interference during inspections of ferrous components. The block is well suited for integration into length-setting procedures, master set comparisons and verification of micrometre or caliper readings, providing a trustworthy intermediate standard for production quality control. Care and handling to preserve measurement confidence Ceramic gauge blocks deliver long service life when cared for correctly: avoid impacts and abrasive contact that can chip the edges, and store the block in a clean, dry environment when not in use. Regular surface cleaning with a lint‑free cloth and suitable solvent keeps contact faces free from oil and debris, maintaining accurate seating during measurements. When traceable calibration is required, arrange calibration intervals that match the workload and measurement uncertainty requirements to retain documented measurement confidence. Select the Metav IndustryLine ceramic gauge block for a stable 75 mm reference and contact Metav Werkzeuge in Emmerich for tailored application guidance: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: M324.075 GTIN: 4054469143446 Material: Ceramic Grade: 1 (DIN 861/1) Nominal length: 75 mm Weight: 0.143 kg Tariff number: 90173000 Specifications Nominal length 75 mm Weight 0.143 kg Tariff 90173000 Features Material ceramic Standard DIN 861/1 Grade 1 Category: End measure / gauge block Compact reference for workshop and calibration use FAQ What tolerance class does this gauge block meet? The ceramic gauge block meets Grade 1 tolerances as specified in DIN 861/1, providing a defined accuracy class for many workshop and inspection applications. Is the 75 mm block suitable for calibration benches and shop checks? Yes; the 75 mm nominal length makes this reference ideal for bench calibration, comparative checks and routine inspection tasks where a compact, stable length standard is required. How should the ceramic block be handled to avoid damage? Handle the block with care to prevent impacts or knocks, keep contact faces clean with a lint‑free cloth and solvent as needed, and store it protected from dust and humidity to preserve measurement integrity. Does the ceramic material affect magnetic or corrosion behaviour? Ceramic is non‑magnetic and corrosion‑resistant, which reduces magnetic interference and helps maintain surface condition compared with some metallic gauges. Can this block be used alongside micrometres and calipers as a reference? Yes; the block is intended as a reference standard for setting and checking micrometres, calipers and other length measuring instruments within its accuracy class. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75 mm Gauge Block, Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Benefit from DIN EN ISO 3650 Grade 0 accuracy together with hardened special steel construction and a compact 75 mm nominal length for reliable reference measurements; order via Metav Werkzeuge or consult the metrology team for specification support. Gauge block 75 mm — End measure, DIN EN ISO 3650 Grade 0 Gauge block 75 mm is a precision end measure designed as a stable reference for dimensional metrology in workshops and laboratories. DIN EN ISO 3650 Grade 0 accuracy Hardened special steel construction Nominal length 75 mm reference standard Cross-section 35×9 mm for standard sizes Accuracy that supports traceable measurement Manufactured to DIN EN ISO 3650, this end measure delivers the dimensional stability expected of a Grade 0 reference. The specification ensures that the block can be employed as a workshop-level reference for setting up comparators and verifying gauges. As a compact 75 mm end measure, it provides a consistent datum for calibration tasks and short-range checks where high repeatability is required. The standardised tolerance band inherent to Grade 0 underpins predictable measurement outcomes across routine quality control processes. Durable construction for long-term reproducibility The body is produced from special steel, hardened to improve wear resistance and resist deformation under frequent use. The hardened finish reduces surface wear during wringing and handling, helping to maintain nominal length over time. A modest mass of 0.18 kg aids in stable placement without unnecessary bulk, while the prescribed cross-section supports lateral stiffness for handling and storage. These material and geometric choices combine to reduce measurement drift and extend the service life of the reference part. Practical integration into inspection workflows This end measure is suitable as a standalone reference or as part of a gauge block set and is identified by SKU M319.750.0 and GTIN 4054469132280 for inventory and procurement systems. The compact format simplifies storage in standard block trays and facilitates frequent use at a workshop bench or in a calibration rig. As a standard-compliant block it complements comparators, micrometers and other precision tools when establishing traceable dimensions; its consistent performance aids process control and helps maintain product conformity in serial production. Contact Metav Werkzeuge for specification matching and to discuss integration of the Metav IndustryLine reference standard into existing calibration procedures: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: M319.750.0 GTIN: 4054469132280 Category: End measures Norm: DIN EN ISO 3650 Facts Nominal length: 75 mm Weight: 0.18 kg Cross-section: 30×9 mm (≤10 mm); 35×9 mm (>10.1 mm) Tariff code: 90173000 Eclass: 21170108 Special features Material: Special steel, hardened Grade: 0 Label: Einzel-Endmaß 75 mm, DIN ISO 3650, Güte 0 DIN ISO 3650 Category path: Messgeräte › Endmasse FAQ What accuracy standard does this gauge block meet? The product is manufactured to DIN EN ISO 3650 and supplied in Grade 0, making it suitable as a precise workshop reference. Is the material of the gauge block suitable for frequent wringing and handling? Yes, the gauge block is made from hardened special steel, which offers improved wear resistance for regular wringing and handling. What is the nominal length and how is the block identified for ordering? The nominal length is 75 mm and the item is listed as SKU M319.750.0 (GTIN 4054469132280) for straightforward procurement. Can this end measure be used with comparator systems and micrometers? The block is intended as a reference standard and integrates with comparators, micrometers and other precision instruments for verification and setup tasks. What cross-section is provided for this nominal length? The applicable cross-section for standard sizes above 10.1 mm is 35×9 mm, which provides the required stiffness for routine handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75 mm Gauge Block, Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of consistent Grade 1 accuracy, hardened special steel construction, and a compact cross-section for stable handling — ideal for repeatable reference measurements in workshops and inspection benches. Order the gauge block directly via Metav Werkzeuge or contact our advisors for specification support. Gauge block 75 mm — Grade 1, DIN EN ISO 3650 (Metav IndustryLine) A 75 mm gauge block manufactured to DIN EN ISO 3650 for use as a calibrated length standard in workshop and laboratory environments Hardened special steel construction Grade 1 tolerance to DIN EN ISO 3650 Nominal length 75 mm for reference measures Compact cross-section for stable handling Traceable accuracy for routine quality control The 75 mm gauge block is produced from hardened special steel and finished to Grade 1 tolerance under DIN EN ISO 3650, ensuring reproducible dimensional references for everyday inspection tasks. As a precision reference, this solid block is suited to comparative checks, verification of micrometre and caliper settings, and routine calibration of inspection fixtures. The standardised tolerance class means measurement uncertainties are predictable, allowing planners to integrate the block into quality-control procedures with confidence. Practical design that supports efficient workflows A compact cross-section delivers rigidity and ease of handling during repeated use: for lengths above 10.1 mm the block follows the larger profile for stable engagement. The moderate mass contributes to steady placement on comparators and flat datum faces without excessive operator fatigue. Finished faces provide reliable seating for slip gauge stacks and limit the need for corrective fixtures. The combination of robust steel and engineered geometry reduces the need for interim handling aids, speeding up inspection cycles in production and maintenance contexts. Long-term stability and maintenance made straightforward Surface hardness and the material choice reduce wear, preserving the block’s reference dimensions over extended service life. Simple maintenance — careful cleaning, lubrication for storage, and avoidance of hard impacts — keeps measurement drift minimal. For traceability and record-keeping, the block’s conformity with DIN EN ISO 3650 supports documentation in calibration routines and internal audits. Pairing this reference with routine verification practices maintains measurement quality across shifts and production batches. For reliable, repeatable length standards choose the Metav IndustryLine 75 mm gauge block — contact Metav Werkzeuge GmbH in Emmerich for delivery and technical guidance to suit inspection requirements Technical data Article number: M319.750.1 GTIN: 4054469132297 Label: Endmaß 75 mm, DIN ISO 3650, Güte 1 DIN ISO 3650 Facts Nominal length: 75 mm Weight: 0.18 kg Cross-section: up to 10 mm → 30 x 9 mm; from 10.1 mm → 35 x 9 mm Tariff number: 90173000 Features Material: hardened special steel Tolerance class: Grade 1 Standard conformity: DIN EN ISO 3650 Category: Gauge blocks / End gauges FAQ What accuracy can be expected from this gauge block? The gauge block M319.750.1 is a Grade 1 reference compliant with DIN EN ISO 3650, providing predictable tolerances suitable for routine workshop and inspection tasks. Is the block suitable for use on a comparator or with slip-gauge stacks? Yes. The hardened faces and stable cross-section of this 75 mm gauge block make it suitable for stack use and comparator-based comparative measurements. Which material is the gauge block made from and how does that affect durability? This Metav IndustryLine gauge block is manufactured from hardened special steel, offering good wear resistance and long-term dimensional stability under normal handling and storage. How should the gauge block be stored to preserve accuracy? Store clean and dry in a protective case or drawer, apply light corrosion inhibitor if needed, and avoid shocks. Regular verification intervals are recommended to document continued conformity. Does the product come with a calibration certificate? Calibration documentation is determined by the specific order; the product meets DIN EN ISO 3650 specifications and can be supplied with appropriate verification records on request. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75 x 9 x 15 mm Gauge Jaw Pair for Go/No-Go Holders, Set of 2 - Metav IndustryLine
Take advantage of compact, precision‑machined flat jaws with exact 75 × 9 × 15 mm dimensions and a paired set for direct replacement — a practical solution that reduces downtime and keeps measurement fixtures ready for repeatable checks. Order the Planschenkel 75 x 9 x 15 mm directly via Metav Werkzeuge or ask the consultants for compatibility advice. Planschenkel 75 x 9 x 15 mm — precision flat jaws, paired set Planschenkel 75 x 9 x 15 mm as compact replacement jaws for measurement fixtures, providing defined contact faces for repeatable setups in workshop and inspection environments Precision‑machined contact faces 75 mm length, 9×15 mm cross‑section Supplied as a pair for quick replacement Consistent contact geometry for repeatable results The machined flat jaws deliver a reliable bearing surface that helps prevent slippage and uneven contact during measurement or clamping operations. With the clear dimensional specification of 75 mm length and a 9×15 mm cross‑section, the component offers predictable behaviour when brought into position on measurement fixtures. This dimensional clarity supports faster setup times and reduces the risk of misalignment, translating into improved process stability for routine inspection tasks. Easy integration into common measuring fixtures Designed as an accessory for standard measuring fixtures and holders, the item fits where defined planar contact is required. The compact profile and paired delivery allow damaged or worn contact faces to be exchanged quickly, restoring the fixture’s original geometry without lengthy adjustments. Identified in stock as M317.113.1, the set is suitable where space is limited but a firm, repeatable mounting is needed. Lightweight handling reduces operator fatigue Weighing just 0.01 kg for the set, the flat jaws are extremely easy to position and handle during repeated tool changes or fixture adjustments. Supplied as a set of two, the pairing ensures symmetric contact surfaces can be restored simultaneously, keeping measurement references consistent and shortening maintenance intervals. The lightweight nature also minimises the load during manual handling and speeds up swap‑outs in busy inspection routines. For compatibility checks, short lead times and expert advice on Metav IndustryLine accessories, contact Metav Werkzeuge in Emmerich — available by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for fast supply and support Technical data SKU: M317.113.1 GTIN: 4054469158228 TARIC: 90173000 Set: 2 pieces Weight: 0.01 kg Facts Length: 75 mm Cross‑section: 9 × 15 mm Special features Accessory for measuring instruments Supplied as a pair Intended use: replacement contact jaws for fixtures FAQ What are the exact dimensions of the jaws? The flat jaws measure 75 × 9 × 15 mm, as stated in the product designation. Are the jaws supplied as a single item or a set? They are supplied as a set of two pieces; the delivery contains a paired set. Is the material specified for these flat jaws? No material specification is provided in the available product data. Can these jaws be used to restore worn contact faces on fixtures? Yes, the item is intended as replacement contact faces for measurement fixtures and is dimensioned for straightforward exchange. How is the item identified for ordering? Stock and ordering reference is M317.113.1 (GTIN 4054469158228). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Achieve traceable reference measurements with a compact ceramic gauge block that combines Grade 1 accuracy and the thermal stability of ceramic material; ideal for workshop inspection and bench calibration. Order the block directly via Metav Werkzeuge or request technical advice from their consultants for application-specific guidance. Ceramic gauge block 8 mm — Grade 1 (DIN 861/1) — Metav IndustryLine Ceramic gauge block 8 mm, Grade 1 DIN 861/1 provides a stable, small-format reference for precision measurements and routine inspection work in metalworking and metrology environments. Grade 1 accuracy per DIN 861/1 Ceramic for thermal stability and wear resistance Compact 8 mm nominal reference block Consistent reference accuracy for routine inspection The Grade 1 classification (per DIN 861/1) indicates a reliable tolerance band suitable for many workshop and production inspection tasks. As an 8 mm nominal block made from ceramic, it offers a low coefficient of thermal expansion and good surface hardness; these properties help to maintain dimensional stability during short-term measurement cycles and reduce drift compared with many metallic gauges. This makes the block an efficient choice where repeatable reference values are required during daily quality checks or comparator set-ups. Practical advantages in the measuring workflow A compact ceramic reference such as this one integrates easily into existing gauge block sets, calibration benches and transfer standards. The small footprint simplifies handling and permits close stacking with other blocks when building gauge stacks. Because the material provides both wear resistance and resistance to mild corrosion, maintenance intervals are extended and handling procedures remain straightforward, supporting reliable throughput in inspection routines and minimising downtime for replacement. Durability, handling and integration into test equipment Ceramic construction combines surface hardness with reduced sensibility to small temperature changes, delivering predictable behaviour across short-term measurement tasks. The block’s light weight and compact form factor allow easy positioning in vises, on parallels or beneath comparators without introducing significant loading effects. Given its role as a reference standard, simple care—cleaning with lint-free cloths and storage in a protective case—is sufficient to preserve accuracy and surface integrity over repeated use. For robust, small-format reference standards rely on the Metav IndustryLine ceramic gauge block — contact Metav Werkzeuge in Emmerich for supply details and application advice. Technical Data Article number: M324.008 GTIN: 4054469143040 Material: Ceramic Nominal size: 8 mm Grade: 1 (DIN 861/1) Weight: 0.013 kg Facts eCl@ss: 21170108 Tariff code: 90173000 SKU: M324.008 Special features Ceramic material for low thermal expansion Grade 1 tolerance band according to DIN 861/1 Category: End gauges / gauge blocks Compact reference size suitable for stacking FAQ What tolerance standard does this block meet? The ceramic gauge block meets Grade 1 tolerances as specified in DIN 861/1, providing a defined tolerance band for routine inspection tasks with the Metav IndustryLine 8 mm block (SKU M324.008). Is the block suitable for use with comparators and gauge sets? Yes — the 8 mm ceramic reference block is intended as a stable reference standard for stacking in gauge sets and for use under comparator anvils in inspection and workshop environments. How should the ceramic block be handled and stored? Handle the block with clean, gloved hands or a lint-free cloth to avoid contamination. Store the block in a protective case or drawer to preserve surface integrity and maintain the precision of the Metav IndustryLine ceramic gauge block. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8 mm Gauge Block Grade 1 DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of Grade 1 conformity and a hardened special steel design for dependable reference checks and reproducible Go/No‑Go inspections; order the gauge directly via Metav Werkzeuge or consult the Metav team for specification advice. End gauge 8 mm (DIN EN ISO 3650) — Grade 1 precision by Metav IndustryLine The End gauge 8 mm (DIN EN ISO 3650, Grade 1) serves as a compact reference for high‑precision dimensional inspection in toolrooms, inspection benches and calibration workflows. DIN EN ISO 3650 Grade 1 tolerance Hardened special steel construction Nominal size 8 mm exact to standard Compact cross‑section 30 x 9 mm Precision that meets the standard and supports reliable decisions This reference is manufactured to DIN EN ISO 3650 and delivered as a Grade 1 end gauge, providing a defined tolerance band suitable for fine inspection tasks. The nominal size 8 mm is produced with tight dimensional control so that it can be used as a measurement standard or a quick Go/No‑Go reference on the production line. The hardened special steel body offers improved wear resistance and dimensional stability, which helps maintain the gauge state over repeated handling and contact cycles. Clear standardisation reduces ambiguity during acceptance tests and supports consistent quality control outcomes. Compact form with practical handling and workshop benefits The slender profile with a 30 x 9 mm cross‑section (applicable for gauges up to 10 mm) keeps the piece easy to position in confined setups while preserving sufficient stiffness for repeatable contact. At approximately 0.01 kg, the component is simple to manoeuvre without special handling tools, which speeds routine checks and spot inspections. Thanks to its compact design and robust surface hardness, the device is well suited for toolroom use, first‑article inspection and integration into inspection benches where space and repeatability are priorities. Traceability and inventory friendly for modern workflows Designed for integration into structured workflows, the piece is identifiable with GTIN and SKU information and pairs cleanly with gauge sets and traceability documentation. The construction and marked standard compliance ensure that it is straightforward to reference in inspection plans and measurement logs, supporting continuity between production and quality assurance. As a compact reference component, it also lends itself to being stored in dedicated racks or tool cabinets so that inventory and audit trails remain transparent and verifiable. For Grade 1 precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for product procurement and technical guidance at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss how this gauge fits into existing inspection routines. Technical Data Article number: M319.080.1 GTIN: 4054469131498 Standard: DIN EN ISO 3650 Grade: 1 Material: hardened special steel Dimensional and measurable data Nominal size: 8 mm Cross‑section: 30 x 9 mm (for sizes ≤ 10 mm) Weight: 0.01 kg Tariff number: 90173000 Features and compliance Grade 1 tolerance per DIN EN ISO 3650 Compact, wear‑resistant hardened body Category: End gauges / reference pieces SKU: M319.080.1 FAQ What tolerance class does this end gauge comply with? The end gauge is manufactured to DIN EN ISO 3650 and meets Grade 1 tolerance requirements, making it suitable as a workshop reference for precision inspection. Which material is used for the gauge and why? The piece is made from hardened special steel, chosen for its wear resistance and dimensional stability under repeated contact, which preserves measurement integrity. Is the part suitable for integration into inventory and traceability systems? Yes, the component includes GTIN and SKU information (GTIN: 4054469131498, SKU: M319.080.1) to support inventory control and traceable documentation in quality workflows. For which applications is this nominal 8 mm gauge most appropriate? This compact reference is ideal for Go/No‑Go checks, first‑article inspections and routine dimensional spot checks in toolrooms and inspection benches. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8 mm Gauge Block, DIN EN ISO 3650 Grade 0, Hardened Special Steel - Metav IndustryLine
Take advantage of DIN EN ISO 3650 conformity and Grade 0 accuracy together with hardened special steel for reliable reference measurements; order the gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Single gauge block 8 mm — Grade 0, DIN EN ISO 3650 (Metav IndustryLine) A single 8 mm gauge block designed as a traceable length standard for workshop calibration, component inspection and precision set-ups in production environments. Grade 0 accuracy (DIN EN ISO 3650) Hardened special steel for long-term stability Compact cross-section 30 × 9 mm for sizes ≤ 10 mm Suitable as a workshop reference standard Consistent, traceable precision for everyday metrology The Single gauge block 8 mm is manufactured to DIN EN ISO 3650 and specified as Grade 0, providing a high level of dimensional fidelity for comparative checks and gauge stack assemblies. Its hardened special steel construction reduces wear and maintains form over repeated use, supporting reproducible measurements across production shifts. As a compact calibration standard, the block is suited to quality-control benches where a stable reference for plug gauges and micrometres is required, offering a practical balance between size and handling. Robust handling and form stability for workshop workflows Engineered with a small footprint and a 30 × 9 mm cross-section for sizes up to 10 mm, the block combines rigidity with easy manipulation during measurement routines. The material choice and heat-treated surface minimise surface deformation, so the reference dimension remains constant during normal workshop operations. The result is a calibration standard that keeps instrument drift to a minimum, helping maintain process capability and reducing downtime for recalibration cycles. Quick integration into inspection routines and gauges Compliance with recognised standards ensures the block can be incorporated into inspection procedures and documentation with confidence. Its nominal size is clearly traceable and suitable for assembling gauge stacks or verifying instrument zero settings. The compact weight and profile allow fast positioning in jigs or on datum plates, while the solid steel body offers durability under frequent contact-based checks, supporting efficient throughput in small-batch and continuous production environments. Order the Metav IndustryLine 8 mm gauge block through Metav Werkzeuge for reliable Grade 0 reference standards and contact our Emmerich team for tailored measurement advice Technical data Article number: M319.080.0 GTIN: 4054469131481 Standard: DIN EN ISO 3650 Material: Hardened special steel Grade: 0 Data Nominal size: 8 mm Weight: 0.01 kg Tariff number: 90173000 Cross-section (≤10 mm): 30 × 9 mm Special features Single gauge block for calibration and reference use Category: Endmasse (gauge block) Suitable for gauge stacks and workshop verification Manufactured for high form stability and wear resistance FAQ What is the declared accuracy of this gauge block? The block is supplied as Grade 0 according to DIN EN ISO 3650, providing a high-precision reference for workshop and production checks. Can this 8 mm block be used in gauge stacks and assemblies? Yes, the 8 mm gauge block is intended for stack assembly and verification work; its compact 30 × 9 mm cross-section eases stacking and alignment in typical inspection procedures. What is the material and why does it matter? Manufactured from hardened special steel, the block offers enhanced wear resistance and dimensional stability, which preserves the reference dimension under repeated contact-based inspections. Is this product traceable for quality documentation? The gauge block conforms to DIN EN ISO 3650, making it suitable for documented inspection processes and calibration routines in quality management systems. What is the SKU for ordering and identification? The product is listed under SKU M319.080.0 and marketed by Metav IndustryLine as a single 8 mm gauge block in Grade 0. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.5 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Benefit from the combination of ceramic construction and Grade 1 accuracy (DIN 861/1) for a stable reference standard; the compact 8.5 mm nominal size and light weight (0.014 kg) make handling and fixture integration straightforward. Order the gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic gauge block 8.5 mm, Grade 1 DIN 861/1 — Metav IndustryLine The Ceramic gauge block 8.5 mm, Grade 1 DIN 861/1 is a compact reference standard designed for length calibration and precision inspection in metrology and quality control. Ceramic construction for dimensional stability Grade 1 accuracy according to DIN 861/1 Nominal size 8.5 mm for fine references Lightweight 0.014 kg, easy to handle Precision that anchors every inspection The compact reference element delivers Grade 1 conformity in accordance with DIN 861/1, providing a reproducible baseline for comparison measurements and routine calibration tasks. Because the nominal size is 8.5 mm, the component is particularly suitable as a fine reference in inspection routines where small steps or narrow gaps require an accurate benchmark. The combination of a defined nominal dimension and recognised grade supports reduced measurement uncertainty and clearer pass/fail decisions in quality control workflows. Stable material for repeatable results Made from ceramic, the block offers high dimensional stability and surface hardness that resists wear under regular use. This material choice supports long-term repeatability when used as a reference master in bench inspections or as part of a gauge-set complement. The light overall mass (0.014 kg) eases handling and placement, allowing technicians to position the standard rapidly without excessive effort, while the robust surface preserves the reference dimension over many measurement cycles. Integrating a compact standard into inspection processes As a small-format reference, this gauge block is straightforward to include in calibration trays and inspection kits where space is limited but accuracy is essential. The element is compatible with comparator setups and visual inspection benches, and its clear specification as Grade 1 (DIN 861/1) simplifies documentation and traceability within quality records. For further specification matching or bespoke gauge-set planning, Metav IndustryLine specialists can advise on the appropriate complementary standards and handling routines to maintain measurement integrity. Discuss application-specific selection or purchase of the Metav IndustryLine Ceramic gauge block 8.5 mm, Grade 1 DIN 861/1 with Metav Werkzeuge—call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M324.008.5 GTIN: 4054469143057 Category: Endmasse Material: Ceramic Grade: Grade 1 (DIN 861/1) Numbers / Core technical data Nominal size: 8.5 mm Weight: 0.014 kg Tariff number: 90173000 Special features Ceramic material Grade 1 precision per DIN 861/1 Compact reference standard SKU: M324.008.5 FAQ What tolerance class does this gauge block meet? The Ceramic gauge block 8.5 mm, Grade 1 DIN 861/1 meets Grade 1 tolerance requirements as defined by DIN 861/1, making it suitable as a workshop reference for fine measurements. Is the gauge block supplied with a calibration certificate? A calibration certificate is not specified for this Ceramic gauge block 8.5 mm, Grade 1 DIN 861/1; any calibration or traceable certification would be noted explicitly in the product listing if included. What advantages does ceramic offer compared with steel gauge blocks? Ceramic provides excellent dimensional stability and surface hardness, reducing wear and maintaining reference dimensions over time; the Metav IndustryLine Ceramic gauge block benefits from these properties for repeatable use. Can the block be used in comparator and gauge-set arrangements? Yes, the compact 8.5 mm nominal size of the block makes it suitable for inclusion in comparator setups and inspection kits where space is limited but reliable benchmarks are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.5 mm Gauge Block Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of a Grade 1 precision reference, produced in hardened special steel and compliant with DIN EN ISO 3650, to secure repeatable go/no‑go checks and calibration routines; order the gauge directly via Metav Werkzeuge or consult our technical advisors for integration into quality control procedures. End gauge 8.5 mm – DIN EN ISO 3650, Grade 1 | Metav IndustryLine The End gauge 8.5 mm is a precision reference for routine go/no‑go inspections and calibration tasks in workshop and laboratory metrology. DIN EN ISO 3650, Grade 1 calibration standard Hardened special steel for long-term stability Precision reference gauge 8.5 mm, traceable Reliable reference for routine inspection and acceptance checks A purpose-made reference such as this end gauge delivers consistent repeatability and a clear acceptance criterion for small diameters. Manufactured to DIN EN ISO 3650, Grade 1, the component serves as a fixed standard for go/no‑go decisions and for verifying plug gauges or measuring instruments. The nominal size of 8.5 mm establishes an unambiguous physical datum, reducing the need for statistical inference during simple pass/fail checks. Where traceable verification is required, a defined standard like this simplifies documentation and supports a streamlined inspection workflow. Robust construction for repeatable handling and storage The body is produced from hardened special steel, providing abrasion resistance and dimensional stability under frequent use. The compact geometry minimises handling error and the specified cross‑section ensures sufficient stiffness for consistent seating in fixtures or gauge blocks. For workshop environments where durability translates to lower lifetime cost, the material choice and manufacturing tolerance combine to preserve the nominal size over many cycles, so that measuring instruments and acceptance procedures remain reliable without frequent corrective action. Practical fit into quality systems and calibration routines As a calibrated reference compliant with recognised norms, this gauge integrates readily into ISO‑based quality systems and routine calibration schedules. The clear identification and traceable marking simplify record keeping, while the small mass and compact form factor allow easy storage in instrument cabinets or protective trays to prevent contamination and damage. For shops that standardise on robust physical masters rather than temporary jigs, such a reference supports faster decisions on part conformity and reduces downstream rework through early detection of out‑of‑tolerance conditions. For traceable measurement standards from Metav IndustryLine, request purchase information and delivery options from Metav Werkzeuge GmbH—telephone +49 2822 7131930 or email info@metav-werkzeuge.com for tailored advice and ordering. Technical Data SKU: M319.085.1 GTIN: 4054469131511 Label: End gauge 8.5 mm, DIN EN ISO 3650, Grade 1 Facts Nominal size: 8.5 mm Weight: 0.01 kg Tolerance grade: Grade 1 Customs tariff number: 90173000 Cross-section: up to 10 mm → 30 x 9 mm; from 10.1 mm → 35 x 9 mm Special features Material: special steel, hardened Standard: DIN EN ISO 3650 Category: End gauges Brand: Metav IndustryLine FAQ What is the intended use of this end gauge? The end gauge is intended as a precision reference for go/no‑go inspections and routine calibration tasks; the Metav IndustryLine End gauge 8.5 mm (SKU M319.085.1) provides a fixed nominal datum for acceptance testing. What standard and tolerance does the gauge follow? This gauge is manufactured to DIN EN ISO 3650 and complies with Grade 1 tolerances suitable for workshop and laboratory reference use. What material is used and how does it affect durability? Constructed from hardened special steel, the gauge offers improved abrasion resistance and dimensional stability, which helps maintain the nominal size under regular handling. Is the size traceable for quality documentation? Yes, the End gauge 8.5 mm from Metav IndustryLine is supplied with clear identification to support traceability in quality records and integration into calibration schedules. How should the gauge be stored to preserve accuracy? Store the gauge clean and dry in a protective tray or cabinet, avoid contact with cutting fluids or corrosive substances, and handle with care to prevent nicks on the measuring faces. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8.5mm End Gauge Single, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of the combination of Grade 0 accuracy, DIN EN ISO 3650 conformity and a hardened special steel construction for a reliable workshop reference that supports repeatable measurement routines. Order the gauge block directly via Metav Werkzeuge or ask the consultants for tailored advice. Gauge block 8.5 mm — single end measure for precision metrology (Metav IndustryLine) Gauge block 8.5 mm is a compact, precision length standard designed for calibration, setting and reference tasks in workshops and inspection labs. Gauge block 8.5 mm, DIN EN ISO 3650 Tolerance Grade 0 for high precision Hardened special steel construction Cross-section 30 x 9 mm for dimensional stability Accurate reference for decisive quality checks The Grade 0 tolerance of this gauge block meets the requirements of DIN EN ISO 3650, providing a documented accuracy level that supports fast, reliable inspection decisions. With a nominal size of 8.5 mm, the block functions as a traceable length reference for comparative measurement operations, tool setting and gauge verification. Using a standardised block reduces uncertainty in routine checks and shortens calibration cycles, which in turn improves throughput in production environments by lowering rework rates and avoiding downstream quality issues. Robust construction that endures workshop use Manufactured from special steel, hardened, this single end measure resists wear and maintains flatness across repeated contact operations. The compact 30 x 9 mm cross-section assigned to sizes up to 10 mm offers good stiffness and handling balance, making the part easy to clamp or insert into gauge sets while limiting torsion during use. Its low net weight contributes to effortless positioning without compromising stability; the material choice and heat treatment together prolong service life and preserve the reference surface quality that underpins consistent measurement results. Practical integration into calibration and production workflows As a bench-top reference, this block suits applications such as checking caliper settings, verifying micrometre behaviour and building gauge stacks for length standards. The compact format supports rapid deployment on inspection benches and in-service measuring stations, reducing setup time when swapping references or assembling measurement chains. For workshops seeking a dependable small-size standard, the combination of proven geometry and hardened material means fewer interruptions for maintenance and predictable repeatability across shifts. Clear identification and procurement advantages The gauge block is delivered under SKU M319.085.0 and is market-ready with a GTIN for inventory control and traceability. Including the customs tariff number helps simplify cross-border procurement and internal logistics. Supplied as a single end measure in the end‑measure category, it complements multi-piece gauge sets and can be stocked as a reference spares item to maintain measurement capability without long lead times. Choosing a standardised component like this supports consistent inspection routines and reduces the administrative burden linked to bespoke measuring tools. Contact Metav Werkzeuge to request the Metav IndustryLine gauge block 8.5 mm (SKU M319.085.0) for reliable length standards delivered from Emmerich and to receive expert guidance on integrating it into existing calibration workflows Technical data Article number: M319.085.0 GTIN: 4054469131504 Standard: DIN EN ISO 3650 Facts Nominal size: 8.5 mm Tolerance grade: 0 Net weight: 0.01 kg Customs tariff number: 90173000 Special features Material: Special steel, hardened Cross-section: 30 x 9 mm (for sizes ≤ 10 mm) Category: Gauge blocks / End measures FAQ What degree of accuracy does this gauge block provide? The gauge block 8.5 mm is manufactured to Grade 0 tolerance under DIN EN ISO 3650, offering a high-precision reference suitable for workshop and inspection use. Which material is used and how does it affect durability? Made from special steel, hardened, the Metav IndustryLine single end measure delivers improved wear resistance and stable contact surfaces for longer service life. How is this block typically used in a calibration routine? This single end measure is used for setting calipers, verifying micrometres and forming part of gauge stacks for comparative length standards; SKU M319.085.0 is convenient for inventorying as a spare reference. Does the cross-section matter for handling or stiffness? Yes — the 30 x 9 mm cross-section (applied for sizes up to 10 mm) provides a balanced profile that improves handling and reduces torsion during measurement tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
80 mm End Gauge Single-Ended Grade 0 DIN EN ISO 3650 Hardened Special Steel - Metav IndustryLine
Take advantage of Grade 0 conformity and hardened special steel construction for a stable, workshop-ready reference standard; the compact 80 mm size combines handling ease with low thermal mass for reproducible checks. Order the single end gauge directly via Metav Werkzeuge or consult our advisors for specification matching and procurement. Single end gauge 80 mm, DIN EN ISO 3650 — Grade 0, hardened special steel (Metav IndustryLine) Single end gauge 80 mm (Grade 0) is a precision gauge block intended for use as a reference standard in test benches, calibration jigs and workshop quality control. DIN EN ISO 3650 Grade 0 accuracy Hardened special steel construction Compact 80 mm reference standard Consistent reference accuracy for routine calibration The gauge block is manufactured to DIN EN ISO 3650 and delivered as a Grade 0 reference, providing a reliable baseline for comparative measurements. The Grade 0 tolerance class ensures reduced uncertainty in short-range checks and makes the block suitable as a traceable workshop standard. For production environments where repeatability of a known length is required, this single 80 mm element offers a straightforward method to verify calipers, micrometres and measuring fixtures. The standardized geometry simplifies integration into existing inspection routines and supports consistent measurement procedures. Robust material and geometry for everyday handling Made from hardened special steel, the block balances wear resistance with machinability during manufacture. The given cross-section specification guarantees stable support and minimal flex during handling and stacking; this stability helps to keep systematic errors low when the block is used as a master gauge. The modest mass and compact dimensions also reduce thermal drift when moved between different workshop zones, maintaining measurement integrity during short-term use. As a single element, it is especially useful where space is limited but a precise, rigid reference is required. Practical benefits for quality workflows and documentation Incorporating this Grade 0 reference into a quality workflow streamlines spot checks and acceptance tests: the defined nominal size of 80 mm simplifies reporting and reduces interpretation effort in inspection records. The block’s construction supports repeated use as a comparative standard, thereby lowering the administrative overhead of frequent recalibration for downstream instruments. When traceability is needed, the product can be recorded in quality documentation as a stable reference element, aiding auditability and process control. Contact Metav Werkzeuge for supply and application advice on the Metav IndustryLine single end gauge 80 mm (SKU M319.800.0) and to discuss how this Grade 0 reference can be integrated into existing quality procedures Technical Data Article number: M319.800.0 GTIN: 4054469132303 Tariff number: 90173000 Facts Nominal size: 80 mm Grade: 0 (DIN EN ISO 3650) Weight: 0.195 kg Cross-section: bis 10 mm 30×9 mm; ab 10.1 mm 35×9 mm Special features Material: Special steel, hardened Category: End gauge / gauge block Intended use: Reference standard for comparative measurements Packaging: single piece FAQ What accuracy class does this 80 mm gauge block conform to? The single end gauge meets DIN EN ISO 3650 Grade 0, providing a workshop-grade reference for short-range comparative measurements. What material is the gauge block made from and why is that relevant? The component is made from hardened special steel, which offers wear resistance and dimensional stability suitable for repeated use as a reference standard. How is this gauge block used in measurement procedures? The 80 mm single element serves as a reference standard for calibrating and checking length-measuring instruments such as calipers and micrometres; it is intended for comparative, traceable checks within quality routines. Which SKU and brand identify this product for ordering? The item is supplied by Metav IndustryLine, SKU M319.800.0, and can be procured through Metav Werkzeuge for direct delivery. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
80 mm Gauge Block Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Precise, hardened construction and conformity to DIN EN ISO 3650 (Grade 1) make this 80 mm end gauge an ideal reference for routine calibration and acceptance tests; the compact cross-section and low mass support stable handling and repeatable results. Order directly via Metav Werkzeuge or consult our advisors for application-specific guidance. End gauge 80 mm — Grade 1 reference standard, hardened special steel (Metav IndustryLine) The End gauge 80 mm serves as a calibrated length reference for inspection benches, workshop quality control and metrology laboratories where stable, repeatable short-range measurements are required Grade 1 accuracy to DIN EN ISO 3650 Hardened special steel construction Compact 80 mm reference standard Low mass 0.195 kg for easy handling Precision built for repeatable reference measurements Manufactured to DIN EN ISO 3650 and specified as Grade 1, this end gauge provides a stable reference point for short-range dimensional control. The combination of a hardened special steel body and precise machining yields a reference suitable for both incoming inspection and routine verification. As a hardened length standard, it reduces wear during repeated contact with measurement anvils and comparator faces, which helps to maintain long-term accuracy. The nominal 80 mm size is common in workshop calibration routines and offers a compact alternative to longer block sets when a single reference length is required. Robust geometry for stable handling and consistent contact The bar profile has a practical cross-section: for sizes above 10.1 mm the cross-section is 35 x 9 mm, a dimension that balances stiffness and ease of clamping in holders or comparator fixtures. With a mass of 0.195 kg, the gauge is light enough for single-person handling yet heavy enough to sit stably on a flat reference surface, reducing the influence of accidental movement during a measurement. The hardened surface resists nicks and abrasion, which contributes to reproducible seating against anvils and micrometre faces. These geometric and material choices translate directly into fewer measurement variations and more reliable day-to-day results. Workflow benefits for quality assurance and traceability As a standardised reference, this gauge simplifies routine procedures: use it for quick checks of micrometres, calipers or comparator setups, or as a control artefact in a small laboratory. Traceability is supported by conformity to established norms, making documentation and audit trails straightforward when the gauge is recorded in inspection logs. The compact format also frees bench space and speeds up handling compared with multi-block sets when only a single nominal length is required. For procurement and stock control the product is identifiable by its SKU and GTIN, facilitating rapid replacement and consistent inventory management. For traceable Grade 1 reference standards from Metav IndustryLine please contact Metav Werkzeuge in Emmerich for application advice and ordering: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M319.800.1 GTIN: 4054469132310 Label: Endmaß 80 mm, DIN ISO 3650, Güte 1 DIN ISO 3650 Facts Nominal size: 80 mm Weight: 0.195 kg Tariff number: 90173000 Cross-section: 35 x 9 mm (for sizes > 10.1 mm) Special features Grade 1 to DIN EN ISO 3650 Material: special steel, hardened Compact reference standard for workshop and lab use Low mass for easy handling and stable seating FAQ What tolerance class does this end gauge meet? The end gauge meets Grade 1 tolerance according to DIN EN ISO 3650, making it suitable as a reliable workshop-grade reference. Is the material corrosion-resistant? The gauge is made from hardened special steel, which provides wear resistance; for enhanced corrosion protection additional measures such as storage in a dry case or light oiling are recommended. Can this gauge be used to calibrate micrometres and calipers? Yes, the End gauge 80 mm is intended as a short-range reference for verifying micrometres, calipers and comparator setups in routine quality checks. What is the cross-section of the gauge and why does it matter? For sizes above 10.1 mm the cross-section is 35 x 9 mm; this geometry improves stiffness and stable contact, which reduces measurement variation during handling. How is the product identified for ordering and traceability? The item is listed under article number M319.800.1 and GTIN 4054469132310, which supports stock management and procurement traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
800mm Gauge Block Set Grade 0, DIN EN ISO 3650, Hardened Special Steel, 35x9mm - Metav IndustryLine
An accurately graded length standard that combines Grade 0 conformity and a hardened special‑steel construction for dependable length verification; ideal where repeatable results and robust handling are required. Order the gauge directly via Metav Werkzeuge or consult the Metav team for specification support. End gauge 800 mm, Grade 0 — hardened special steel, DIN EN ISO 3650 (Metav IndustryLine) The End gauge 800 mm, Grade 0 is a hardened length standard for workshop and calibration use, designed to fulfil DIN EN ISO 3650 requirements for traceable, repeatable length checks. Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel for long-term stability Nominal length 800 mm with 35 x 9 mm cross-section Robust profile with manageable weight of 3.2 kg Reliability and standard conformity that speeds up inspection work This length standard delivers Grade 0 conformity in accordance with DIN EN ISO 3650, providing a clear, comparable benchmark for acceptance tests and instrument verification. The declared tolerance class reduces interpretation overhead during quality control and supports fast go/no‑go decisions on production lots. As a purpose‑built length standard, it enables laboratories and workshops to document measurement capability with a recognised normative reference, which enhances traceability and simplifies audit procedures. Material and profile designed to keep measurements consistent Constructed from hardened special steel, the gauge combines surface stability with mechanical resistance to shocks and handling. The compact 35 x 9 mm cross‑section yields a stiff profile across the 800 mm length while keeping the overall mass at 3.2 kg, making two‑person handling feasible without excessive effort. The hardened finish lowers wear and the need for frequent reconditioning; the result is a durable standard that retains geometry and reduces downtime for replacement or repair. Practical use cases in workshop and calibration environments Placed in the category for large length standards (500–1,000 mm), this gauge suits assembly inspection, calibration benches and machine tool setup where an 800 mm datum is required. The robust geometry supports repeated seatings against machine tables, stop systems or comparator anvils without compromising the reference face. Thanks to the normative backing of DIN EN ISO 3650, the gauge is also suitable for contractual checks and for establishing master measurements when integrating components across multiple production stages. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine End gauge 800 mm into existing inspection routines and to arrange procurement directly through our Emmerich supply centre Technical Data Article number: M320.800.0 GTIN: 4054469132563 Nominal length: 800 mm Material: Special steel, hardened Grade: 0 Standard: DIN EN ISO 3650 Cross-section: 35 x 9 mm Weight: 3.2 kg Tariff number: 90173000 Facts Nominal length: 800 mm Cross-section dimensions: 35 x 9 mm Mass: 3.2 kg Accuracy class: Grade 0 Applicable standard: DIN EN ISO 3650 Special features Hardened special steel construction Designed as a length standard for verification and calibration Robust profile for low deformation over repeated use Suitable for inspection benches and machine tool set-up FAQ What accuracy class does this gauge conform to? The End gauge 800 mm is supplied as Grade 0 and complies with DIN EN ISO 3650, giving a normative reference suitable for laboratory and workshop checks. Which material is used for the gauge and what is the benefit? The gauge is made from hardened special steel, which improves wear resistance and profile stability for repeated measurement use. Is the gauge suitable for machine tool set-up and jig checking? Yes; the 800 mm nominal length and stiff 35 x 9 mm cross‑section make it appropriate for machine set‑up, fixture checks and larger assembly inspections. How heavy is the 800 mm end gauge and how does that affect handling? With a mass of 3.2 kg, the gauge is substantial enough for stable seating while remaining manageable for two‑person handling and routine repositioning. What standard should be referenced for contractual checks using this gauge? Use DIN EN ISO 3650 as the normative reference when documenting contractual or batch acceptance measurements with this gauge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
800mm Gauge Block Set Grade 1, DIN EN ISO 3650 Hardened Special Steel - Metav IndustryLine
Benefit from a combination of DIN EN ISO 3650 conformity, a Grade 1 tolerance and a hardened special‑steel construction for stable, reproducible length standards; order the gauge directly via Metav Werkzeuge or request technical advice from our consultants. End gauge M320.800.1 — 800 mm Grade 1 end measure (DIN EN ISO 3650) A Metav IndustryLine End gauge 800 mm designed as a robust length standard for calibration and dimensional control in inspection and production environments. Grade 1 tolerance to DIN EN ISO 3650 Hardened special steel for long-term stability 800 mm nominal length, 35×9 mm cross-section Robust 3.2 kg construction for workshop use Reproducible accuracy for routine and audit measurements The M320.800.1 end gauge is specified to Grade 1, complying with DIN EN ISO 3650, which makes it suitable where consistent, repeatable length standards are required. As an 800 mm nominal standard, it provides a clear reference for comparative checks and functional tests, reducing uncertainty during verification tasks. The compliance with this international norm supports traceable practices in quality assurance and simplifies documentation for internal audits or external certification activities. Robust design that reduces handling and measurement errors Constructed from hardened special steel, the gauge combines surface hardness with dimensional stability to withstand regular workshop use without rapid wear. The rectangular cross‑section of 35×9 mm gives a favourable stiffness-to-weight ratio, while the total mass of 3.2 kg helps the standard remain stable during contact measurements. These physical characteristics lower the risk of deflection during handling and ensure that the reference dimension remains consistent across repeated comparisons, supporting faster inspection cycles and fewer rework loops. Suited to larger assemblies and integration into calibration workflows Classified in the Large range (500–1,000 mm), this end standard bridges the gap between bench‑scale artefacts and long‑bar measures used in heavy machining or assembly halls. It is particularly useful for fixture setting, end‑to‑end checks on housings and for verifying machine zero positions where a long, rigid reference is needed. Backed by Metav’s product range and distribution in Emmerich, the gauge integrates into broader quality concepts — enabling accessible precision without the need for multiple specialised suppliers and supporting dependable supply chains for workshops and distributors. For procurement or tailored technical advice on the M320.800.1 end gauge and its applications, contact Metav Werkzeuge directly for a competent recommendation and ordering support at +49 2822 7131930 or info@metav-werkzeuge.com Technical data SKU: M320.800.1 GTIN: 4054469132570 Designation: End gauge 800 mm, DIN EN ISO 3650, Grade 1 Manufacturer: Metav IndustryLine Core specifications Nominal length: 800 mm Cross-section: 35×9 mm Weight: 3.2 kg Tolerance grade: 1 Tariff number: 90173000 ECLASS: 21170108 Materials & standards Material: Special steel, hardened Standard: DIN EN ISO 3650 Application: Length standard for calibration and inspection Category: Large range (500–1,000 mm) Images: m3201250-main.jpg, m3201250-detail.jpg FAQ What tolerance class does this end gauge follow? The M320.800.1 is manufactured to Grade 1 tolerances in accordance with DIN EN ISO 3650, providing a reproducible reference for length checks. Is the material suitable for frequent workshop use? Yes, the end gauge is made from hardened special steel, offering improved wear resistance and dimensional stability for regular inspection and set‑up tasks. For which applications is an 800 mm end gauge most suitable? An 800 mm length is ideal for fixture setting, verifying machine positions and comparative length checks on medium to large assemblies within the Large range (500–1,000 mm). Does the product include a calibration certificate? A calibration certificate is not implied by the product data provided; calibration services and accompanying certificates can be arranged on request through Metav Werkzeuge. How does the cross‑section affect handling and stability? The 35×9 mm cross‑section offers a balance of stiffness and manageable mass, reducing deflection during contact measurements and simplifying handling during routine checks. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
80mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Precision measurement for small assemblies benefits from the combination of Grade 1 accuracy, a thermally stable ceramic body and the compact 80 mm nominal length. Secure traceable reference checks and straightforward integration into inspection routines by ordering the gauge directly via Metav Werkzeuge or consulting the technical advisors for application guidance. Ceramic End Gauge 80 mm, Grade 1 (DIN 861/1) — Metav IndustryLine A Ceramic End Gauge 80 mm, Grade 1 (DIN 861/1) designed as a compact reference standard for dimensional inspection and machine setup in quality control and laboratory environments Grade 1 accuracy to DIN 861/1 High-stability ceramic body Compact 80 mm reference standard Non-magnetic and corrosion-resistant Stable reference for accurate dimensional inspection The Grade 1 classification in accordance with DIN 861/1 denotes a high level of dimensional fidelity for an 80 mm reference. As a compact end standard, the component offers a reliable basis for comparative measurement and machine setting tasks where reproducibility is essential. The ceramic composition reduces thermal drift compared with many metals, so readings remain consistent during short-term temperature changes commonly encountered in workshops and calibration benches. This stability supports efficient quality-control workflows and minimises rework. Practical handling and workshop integration Lightweight construction at approximately 0.153 kg and the compact 80 mm nominal length make the block easy to position on small fixtures and in tight setups. The gauge functions as a stable reference in routine inspection sequences and for transfer measurements between instruments. Compatibility with common bench procedures and the standard format simplifies inventorying and traceability within an inspection schedule. The robust material and finished faces ensure contact reliability during repeated use, supporting steady measurement throughput in production environments. Material advantages that extend service life Ceramic offers distinct functional benefits for a length standard: low thermal expansion, high surface hardness and inherent wear resistance prolong the service life of the measuring faces. In addition, the non-metallic nature provides non-magnetic behaviour and chemical resistance, which helps when parts are coated or exposed to humid conditions. These properties reduce handling precautions compared with softer materials and contribute to long-term dimensional integrity, making the gauge a cost-effective reference for precision work. For procurement or technical specification assistance on the Metav IndustryLine ceramic end gauge, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice and order processing Technical data Article number: M324.080 GTIN: 4054469143453 eClass: 21170108 Tariff number: 90173000 Facts Nominal size: 80 mm Weight: 0.153 kg Grade: 1 Standard: DIN 861/1 Special features Material: Ceramic Category: End measures (Endmasse) Label: Keramik-Endmaß 80 mm, Güte 1 DIN 861/1 Brand: Metav IndustryLine FAQ What level of accuracy does Grade 1 imply for this end gauge? Grade 1 according to DIN 861/1 denotes a high level of dimensional accuracy for an 80 mm reference; the Metav IndustryLine ceramic end gauge meets the tolerances defined by that standard for Grade 1 instruments. Is the ceramic construction suitable for use with magnetic workpieces? Yes, the ceramic body is non-magnetic, so the gauge can be used in proximity to magnetic components without affecting magnetic behaviour or introducing measurement interference. How should the gauge be stored to preserve accuracy? Store the block in a clean, dry environment, protected from shocks and extreme temperature swings; keep faces free of contaminants and handle with care to maintain the measuring surfaces. Can this end gauge be used as a reference in laboratory calibration routines? The ceramic end gauge functions as a reference standard within calibration procedures and inspection chains; specific calibration status or certificates depend on the selected service and laboratory protocols. What advantages does ceramic offer compared with steel reference blocks? Ceramic provides lower thermal expansion, excellent surface hardness and corrosion resistance, which together reduce drift and surface wear during repeated contact measurements, extending usable life. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
87 Piece Gauge Block Set 1.001–100 mm Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of precise, hardened special‑steel construction and full compliance with recognised standards for reliable reference measurements; the comprehensive set and protective case ensure durable storage and safe transport. Order the set directly via Metav Werkzeuge or contact a consultant for tailored advice. Parallel gauge set M318.871 — hardened special‑steel reference set (DIN EN ISO 3650) The Parallel gauge set M318.871 serves as a workshop and calibration reference, providing precise, traceable reference lengths for quality control and tool setting across mechanical and metalworking environments Hardened special‑steel construction DIN EN ISO 3650 compliance Wide size range for workshop use Supplied in a protective case Precision reference for consistent quality control A comprehensive gauge set delivers a stable baseline for dimensional checks and calibration. The hardened special‑steel composition creates a wear‑resistant contact surface that preserves measurement integrity over time. Compliance with DIN EN ISO 3650 confirms that the set meets established tolerances for gauge blocks, which simplifies integration into existing quality processes and supports repeatable results in inspection routines. Using stable reference lengths reduces rework and supports faster setup of fixtures and jigs. Robust construction that endures workshop conditions Manufactured from heat‑treated special‑steel, the components resist surface deformation and maintain flatness under regular use. The solid material choice offers a balance between toughness and dimensional stability, so the set remains a dependable metrological reference in busy production areas. Where durability matters, the robust design reduces the frequency of replacements and contributes to lower life‑cycle costs compared with softer measuring standards. Practical handling and protected storage for reliability The set is supplied in a protective case that streamlines transport and on‑bench organisation, keeping individual gauges protected from impact and contamination. Clear labelling and systematic arrangement in the case enable rapid selection and return of gauges during inspection tasks, improving workflow efficiency. Traceability is supported by the set’s conformity to recognised standards, facilitating documentation for internal quality records and audits. Designed for everyday workshop and calibration tasks As a reference collection intended for routine use, the set covers a broad range of sizes suitable for machine‑shop measurement, fixture verification and tool setting. The combination of standard conformity and hardened surfaces means the set is appropriate for regular inspection cycles and for supporting calibration intervals within a production environment. Where precise, repeatable lengths are required, the set functions as a reliable metrological backbone. For a quote or to discuss suitability for a specific application, contact Metav Werkzeuge for personalised advice and fast supply from Emmerich. Technical data Article number: M318.871 GTIN: 4054469129907 Manufacturer: Metav IndustryLine Facts Pieces per set: 87 Net weight: 2.7 kg Tariff number: 90173000 Standard: DIN EN ISO 3650 Special features Material: Special steel, hardened Delivered in protective case for transport and storage Designation: Parallel end gauge set, DIN 861/1 Complete set for workshop reference measurements FAQ What materials are the gauges made from? The gauges are manufactured from hardened special‑steel, providing wear resistance and long‑term dimensional stability for the Parallel gauge set M318.871. Is the set suitable for routine workshop inspection? Yes, the set is designed for workshop and calibration tasks; the material and conformity to DIN EN ISO 3650 make it suitable for regular inspection and tool‑setting duties. Does the set include a case for storage and transport? The Parallel gauge set M318.871 is supplied in a protective case to safeguard components during transport and to keep gauges organised on the bench. Which standards does the set conform to? The set is specified to DIN EN ISO 3650, aligning it with recognised requirements for gauge blocks and facilitating traceable reference measurements. Can the set be used for accreditation or audit documentation? The standard conformity and stable material properties support use as a reference in internal quality records and audits; further calibration documentation can be requested as required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
87 Pieces Gauge Block Set 1.001–100 mm Hardened Special Steel DIN EN ISO 3650, Supplied in Case - Metav IndustryLine
Take advantage of a hardened special steel construction and compliance with DIN EN ISO 3650 to secure reliable reference lengths and fast set-up in production and inspection. Combine durable material with a comprehensive size range to reduce measurement conversion time and ensure reproducible results; order the set directly through Metav Werkzeuge or consult our experts for specification guidance. Parallel gauge block set M318.870 — hardened special steel, DIN EN ISO 3650 (Metav IndustryLine) The Parallel gauge block set provides stable reference lengths for precision setting, calibration and inspection tasks across machine shops and quality departments. Gauge blocks to DIN EN ISO 3650 Hardened special steel construction Comprehensive size range for precision set-up 87-piece configuration for flexible combinations Reliable material and standard conformity for repeatable measurements Constructed from special steel and delivered to the applicable standard DIN EN ISO 3650, this set offers a stable, wear-resistant reference for length measurement. The hardened surfaces reduce abrasion and preserve parallelism during repeated use, which directly improves measurement reproducibility on the shop floor. Where calibration intervals and traceability matter, the material choice and standard conformity minimise drift and support consistent inspection results over time. Practical set composition that speeds up setup and inspection The composition covers a wide span of incremental lengths so that precise stacks can be built without resorting to time-consuming shims or improvised gauges. As gauge blocks, the elements are intended for straightforward stacking and pairing to create exact reference dimensions, facilitating faster set-up of workholding and inspection fixtures. Fewer adjustments are required when a comprehensive range of end measures is available, improving throughput and reducing non-productive time in repetitive tasks. Clear benefits for quality assurance and workshop efficiency Using calibrated reference blocks as stable length standards supports a predictable quality regime: dimensional checks become quicker and deviations easier to interpret. The robust design reduces the need for frequent replacement, which lowers lifecycle disruption and helps maintain a reliable calibration baseline for incoming inspection and in-process control. For operations that depend on repeatable alignment and assembly, the set serves as a practical tool to uphold production tolerances. For DIN-compliant reference standards, choose the Metav IndustryLine gauge block set and contact Metav Werkzeuge in Emmerich for procurement and technical advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M318.870 GTIN: 4054469129891 Manufacturer: Metav IndustryLine Facts Weight: 2.7 kg Pieces per set: 87 Customs tariff number: 90173000 Size distribution: elements covering nominal lengths from ~1.001 mm up to 100 mm Special features Material: Special steel, hardened Standard: DIN EN ISO 3650 Set type: Parallel end measures for length reference Category: End measures FAQ What accuracy class or tolerance can be expected from these gauge blocks? The Parallel gauge block set meets the dimensional and surface requirements associated with DIN EN ISO 3650, providing the reproducible reference performance expected of hardened end measures for workshop and inspection use. Are these end measures supplied calibrated? The set is supplied as a complete reference block set; calibration status is indicated per individual offer—please check the specific product data for calibration certificates where required. Which applications are most suitable for this gauge block set? This set is suited to machine shops, metrology benches and quality control where consistent length standards are needed for fixture set-up, inspection and adjustment tasks with hardened special steel benefits. Can the set be used for routine calibration of gages and instruments? Yes, the blocks serve as practical length references for routine checks and cross-verification of measuring equipment when applied in stable environmental conditions. Is the set compatible with high-volume production environments? The hardened construction and broad size range make the set appropriate for repeated use in production settings, helping to maintain measurement repeatability and reduce downtime. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
87 Pieces Precision Gauge Block Set 1,001–100 mm, Hardened Special Steel, DIN EN ISO 3650, In Case - Metav IndustryLine
Take advantage of a comprehensive 87-piece gauge set manufactured from hardened special steel and produced to DIN EN ISO 3650, providing reliable, repeatable reference measures for workshop inspection and fixture set-up; the set is supplied in a protective case for organised storage and transport. Order the set directly via Metav Werkzeuge or consult the technical team for application support. Parallel end gauge set 87/2 (87 pieces) — hardened special steel, DIN EN ISO 3650 Parallel end gauge set 87/2: a precision gauge-block style set for dimensional inspection and setting reference standards in workshop and quality environments Hardened special steel construction Conforms to DIN EN ISO 3650 Comprehensive 87-piece assortment Supplied in a protective case Durable construction for consistent reference measures Constructed from hardened special steel, the set delivers durability and wear resistance that matter in daily shop use. Conformity with DIN EN ISO 3650 ensures manufacturing tolerances and interchangeability across batches, which supports consistent results when used as reference measures for calibration, gauge setting and comparative checks. The material choice reduces the need for frequent replacement and keeps maintenance effort low, contributing to dependable long‑term performance in production and inspection routines. Wide size range for versatile workshop use The 87-piece set covers a broad sequence of sizes, permitting fine graduations and the assembly of direct lengths for setting and inspection tasks. Individual blocks may be combined to achieve required dimensions, enabling quick adaptation to measuring and fixture requirements without additional machining. This versatility supports rapid, rational workflows and shortens set-up times at inspection benches and on production machines, thereby increasing throughput and reducing idle time. Organised storage and straightforward handling Supplied in a protective case, the set is designed for orderly storage and transport while protecting individual gauges from damage. The total mass of approximately 2.7 kg keeps the kit manageable for single-person handling yet substantial enough to feel robust. Clear labelling and compartmentalisation speed the selection process and minimise handling errors, which translates into fewer measurement interruptions and steadier quality control across shifts. For procurement and tailored advice on application or set composition, contact Metav Werkzeuge—Metav IndustryLine’s specialist team is available to assist with selection and delivery via info@metav-werkzeuge.com or +49 2822 7131930. Technical Data Article number: M318.872 GTIN: 4054469129914 Weight: 2.7 kg Pieces per set: 87 Material: Special steel, hardened Standard: DIN EN ISO 3650 Tariff number: 90173000 Facts SKU: M318.872 Category: End gauges Set: Yes Case included: Yes Special features Protective storage case for transport and organisation Mass composition: 9x1.001–1.009 / 49x1.01–1.49 / 19x0.5–9.5 / 10x10–100 Robust workshop design for frequent use FAQ What sizes are included in the set? The Parallel end gauge set 87/2 contains a staged selection of blocks covering the range indicated in the specification, arranged to allow combination into required lengths and fine increments. Is the set suitable for routine quality control in a machine shop? Yes, the set was designed for workshop and inspection use; the hardened special steel and DIN EN ISO 3650 production standard make it appropriate for routine dimensional checks and gauge setting. Does the delivery include a storage case? Yes, the set is supplied in a protective case to keep individual gauges organised and protected during transport and storage. What is the manufacturer and SKU for ordering? The kit is offered through Metav IndustryLine with SKU M318.872 and can be ordered directly from Metav Werkzeuge. Can the gauges be used as reference standards for calibration work? The gauges fulfil the DIN EN ISO 3650 standard, providing traceable production tolerances suitable for many inspection and setting tasks; for formal calibration certificates, please consult the Metav team. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
87mm–100mm Carbide Parallel Gauge Set, 87 Pieces, DIN EN ISO 3650, Supplied in Case - Metav IndustryLine
Reliable dimensional reference thanks to carbide construction and compliance with DIN EN ISO 3650; the compact 87-piece range and organised protective case support consistent inspection routines and long service life. Secure the set directly via Metav Werkzeuge or consult our specialists for application advice. M322.870 — 87-piece Carbide Parallel Gauge Block Set (DIN EN ISO 3650) by Metav IndustryLine The M322.870 is a carbide 87-piece parallel gauge block set designed as a stable reference for calibration and inspection tasks in toolrooms, production measurement and quality control. 87-piece carbide set to DIN EN ISO 3650 Size coverage 1.001–100 mm in graduated steps Supplied in protective transport case Precise reference for calibration and inspection Durable reference for routine inspection and calibration Constructed from carbide, this gauge block set is built for wear resistance and dimensional stability. The material choice reduces surface wear during repeated wringing and contact use, which keeps the blocks within tolerance for longer and lowers the frequency of replacement. As a result, inspection intervals remain predictable and traceable, supporting efficient quality control processes and reducing measurement-related downtime. Wide coverage in compact organisation speeds up workflow The set covers sizes from 1.001–100 mm in finely graded steps across 87 pieces, offering a practical balance between reach and manageability. The graded configuration enables quick build-up of nominal lengths without unnecessary stacking, which simplifies set-up times for calibration tasks and in-process checks. This breadth of sizes makes the kit suitable for small components as well as larger assemblies, providing a single reference set that replaces multiple partial collections. Ready for the workshop: protected transport and easy handling Supplied in an organised protective case, the blocks remain secure and identifiable during storage and transport; the compact footprint supports bench-level use and orderly inventory. With a net weight of 4.2 kg, the set is robust yet portable, enabling shared use between inspection benches without undue handling effort. The case arrangement reduces the risk of accidental damage and keeps each gauge block immediately accessible for fast measurement cycles. Standardised accuracy for dependable metrology results Manufactured to DIN EN ISO 3650, the set provides a recognised standard for gauge blocks used in industrial calibration and verification. The compliance ensures compatibility with established calibration routines and integration into quality assurance documentation. For toolrooms and inspection labs seeking a reliable reference material, this set offers a pragmatic combination of precision, durability and comprehensive size selection supplied under the Metav IndustryLine quality umbrella. Contact Metav Werkzeuge today to obtain the M322.870 set from Metav IndustryLine and arrange delivery from Emmerich; specialists are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M322.870 GTIN: 4054469132730 Category: Endmasse Manufacturer: Metav IndustryLine Facts Pieces per set: 87 Weight: 4.2 kg Customs tariff number: 90173000 Special features Material: Carbide Standard: DIN EN ISO 3650 Set composition: 9×1.001–1.009 mm / 49×1.01–1.49 mm / 19×0.5–9.5 mm / 10×10–100 mm Supplied in protective transport case FAQ What material are the gauge blocks made from? The gauge blocks in this set are made from carbide, which provides high wear resistance and long-term dimensional stability for reference measurements. Is the set suitable for calibration and traceable measurement routines? Yes, the set is manufactured to DIN EN ISO 3650 and serves as a standard reference for calibration and inspection tasks in production and toolroom environments. What size range does the set cover? The set covers sizes from 1.001 mm up to 100 mm across 87 pieces in a graduated composition for flexible build-up of nominal lengths. Is a protective case included for transport and storage? The blocks are supplied in a protective transport case to keep the set organised and to reduce the risk of damage during handling and storage. Can the set be used for both small precision parts and larger assemblies? Yes, the combination of fine small sizes and larger blocks allows the set to serve both fine mechanical measurements and checks on larger components. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9 Calibration Gauge Blocks Set 5.1/10.3/15/20.2/25/50/75/100 mm, Grade 1, Wooden Case - Metav IndustryLine
The supplied product data contains contradictory information about the composition of the gauge block set and cannot be processed into a full product description in its current form. Specifically, the product label describes the set as eight gauge blocks plus a flat glass, while other supplied entries indicate nine gauge blocks and list the piece count as nine; these statements are inconsistent and make it unclear whether the set comprises eight or nine measuring blocks (and whether the flat glass is counted separately). Please correct the dataset so that the number of gauge blocks and the total contents of the set are consistent across all fields. Once the product contents are clarified, a complete, standards-compliant description and technical specification can be produced.
9 mm Gauge Block Grade 1 DIN EN ISO 3650 Hardened Special Steel - Metav IndustryLine
Take advantage of a compact length standard that combines traceable conformity, hardened special steel construction and a cross-section optimised for handling; the result is precise, repeatable measurements with a small footprint. Order directly via Metav Werkzeuge or contact our consultants for specification and supply details. Gauge block 9 mm — hardened length standard, DIN EN ISO 3650, Grade 1 The gauge block 9 mm is a hardened, high‑accuracy length standard intended for calibration tasks and dimensional checks in industrial metrology and laboratory environments. DIN EN ISO 3650 Grade 1 accuracy Hardened special steel construction Compact cross-section 30 x 9 mm for stable handling Traceable identification with GTIN and SKU Precision that supports reliable quality control This length standard is manufactured to DIN EN ISO 3650 and shipped as Grade 1, which communicates a predictable tolerance band suitable for routine and elevated inspection tasks. The compact nominal size of 9 mm stabilises thermal behaviour and reduces handling errors, while the hardened special steel substrate delivers surface integrity and wear resistance. As a consequence, this precision gauge provides a consistent reference for setting micrometres, calipers and optical comparators, supporting faster decisions on conformity and reducing downtime in measurement workflows. Robust form for repeatable measurements A cross-section of 30 x 9 mm (applies for nominal sizes up to 10 mm) gives the block a practical balance between mass and manoeuvrability: it is heavy enough to sit steadily during measurements yet small enough for rapid alignment in a set. The hardened finish minimises surface distortion and prolongs service life under regular use. At roughly 0.01 kg, handling is effortless and integration into existing gauge sets or storage systems is straightforward. Bold surface quality and consistent geometry together mean fewer rechecks and a dependable master for day‑to‑day inspection routines. Traceability and integration into calibration regimes The product is supplied with clear identification (SKU M319.090.1 and GTIN 4054469131535), which simplifies inventory and traceability within quality management systems. As a standardised length artefact, this block serves both as a direct calibration reference and as part of comparative checks that support internal audits and external conformity records. The hardened construction reduces the frequency of recalibration caused by wear, contributing to lower total cost of ownership over a measurement asset’s lifecycle. Where traceability chains and documented calibration history are required, this gauge block fits into established workflows and laboratory procedures. Practical benefits for workshop and laboratory use Because this block adheres to an international standard and is produced from hardened special steel, it is suitable for repeated contact with precision instruments without rapid degradation. The small form factor makes it an efficient choice for toolrooms, inspection benches and portable calibration kits, while the clear SKU and GTIN support procurement, stock control and digital asset tracking. Pairing standard conformity with a wear‑resistant material gives technicians a compact, reliable reference that keeps inspection throughput steady and predictable. Contact Metav Werkzeuge to confirm suitability for specific calibration chains and to arrange supply from Emmerich with full product documentation Technical Data Article number: M319.090.1 GTIN: 4054469131535 SKU: M319.090.1 Category: Endmasse Facts Nominal size: 9 mm Standard: DIN EN ISO 3650 Grade: 1 Weight: 0.01 kg Customs tariff number: 90173000 Special features Material: special steel, hardened Cross-section: 30 x 9 mm (for nominal sizes ≤ 10 mm) Intended use: length standard for calibration and dimensional checks Packaging: standard commercial packing for measurement tools FAQ What level of accuracy does this gauge block provide? This Grade 1 gauge block meets the tolerance band specified by DIN EN ISO 3650 and is intended for reliable workshop and inspection use where traceable conformity is required. Is the block suitable for inclusion in a master set for daily inspection work? Yes; the hardened special steel construction and compact cross-section make it a practical master reference within a gauge block set or portable calibration kit. How is the product identified for inventory and traceability? Identification is supported by SKU M319.090.1 and GTIN 4054469131535, enabling straightforward recording in quality management systems and procurement workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
9 mm Gauge Block Single End, Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of DIN EN ISO 3650 Grade 0 accuracy combined with a hardened special steel construction in a compact 9 mm reference element; order directly via Metav Werkzeuge or consult our experts for procurement and application advice. Single gauge block 9 mm – DIN EN ISO 3650, Grade 0 (Metav IndustryLine) A single gauge block 9 mm designed as a precision reference for workshop and laboratory measurement tasks, suitable for use in inspection, calibration sets and reference stacks DIN EN ISO 3650 Grade 0 tolerance Hardened special steel construction Compact 30 x 9 mm cross-section Traceable reference for precision measuring Reliable reference accuracy for reproducible inspection results The product serves as a high-value reference element where repeatable dimensional control is essential. Manufactured to DIN EN ISO 3650 and specified as Grade 0, this gauge block provides tight manufacturing tolerance that reduces measurement uncertainty in routine inspection. The hardened special steel body limits wear and dimensional drift, making the block a stable standard for reference stacks or comparative checks in both workshop and metrology lab environments. Practical benefits include minimal thermal distortion during short handling and consistent contact behaviour on precision surfaces. Compact form factor that supports efficient workflows The compact cross-section and low mass make the block easy to handle and integrate into existing sets without adding bulk to a workstation. At a nominal size of 9 mm and a cross‑section of 30 x 9 mm, the device is optimised for stacking and for close‑tolerance assembly checks where space and manoeuvrability matter. This compact geometry shortens setup times for repeat measurements and simplifies the routine process of building reference stacks, which contributes directly to improved throughput in quality control tasks and a faster decision loop between measurement and production adjustments. Built for durability and consistent reference performance Constructed from hardened special steel, the block resists surface wear and preserves flatness under normal use, ensuring a long service life as a workshop reference. The combination of material selection and Grade 0 tolerance means fewer replacements and more dependable reference values over time, supporting cost‑efficient metrology practices. As part of Metav’s offering, this reference element benefits from the company’s quality filtering at its Emmerich location, a factor that underpins supply reliability and long‑term availability for procurement planning. Contact Metav Werkzeuge today to secure the Metav IndustryLine 9 mm gauge block (SKU M319.090.0) for your reference set and request further technical details Technical data SKU: M319.090.0 GTIN: 4054469131528 Standard: DIN EN ISO 3650 Nominal size: 9 mm Tolerance grade: Grade 0 Material: Hardened special steel Weight: 0.01 kg Facts Nominal size: 9 mm Cross-section: 30 x 9 mm (applies up to 10 mm) Weight: 0.01 kg Tariff number: 90173000 ECLASS: 21170108 Special features Single gauge block (individual end measure) Grade 0 accuracy per DIN EN ISO 3650 Hardened special steel construction Category: Endmasse (gauge blocks) FAQ What tolerance class does this gauge block meet? The single gauge block 9 mm meets Grade 0 tolerance according to DIN EN ISO 3650, providing a high level of dimensional accuracy suitable for reference use with Metav IndustryLine items such as SKU M319.090.0. Which material is used for the gauge block? This reference element is made from hardened special steel, chosen for wear resistance and stability under normal handling procedures, as specified for the Metav IndustryLine single gauge block 9 mm (M319.090.0). Can the block be used in a reference stack for calibration checks? Yes; the 9 mm individual block is suited for inclusion in reference stacks and comparative inspection sets where a Grade 0 element is required for precise length combinations. Is this gauge block intended for workshop use or lab use? The design supports both workshop and laboratory applications: its compact form and Grade 0 accuracy make the block appropriate for everyday inspection tasks as well as for controlled metrology procedures using Metav IndustryLine standards (SKU M319.090.0). How should the gauge block be handled and stored to maintain accuracy? Handle with clean, dry gloves if possible and store in a dry, dust‑free case to protect the finished faces; regular cleaning and correct stacking practice will help preserve the Grade 0 accuracy of the Metav IndustryLine 9 mm block (M319.090.0). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
ensure traceable length calibration with gauge blocks
gauge blocks, also called slip gauges or end gauges, are precision length standards designed to transfer exact measures during calibration and setup. Manufactured and graded for metrological use, they provide the reference dimensions needed to verify and adjust measuring instruments in industrial workshops and calibration labs.
how gauge blocks work and where they are essential
gauge blocks are used to create known lengths by wringing individual blocks together or by using a single block as a reference. length calibration in industry commonly relies on parallel gauge blocks, while angle, cylinder and sphere end gauges serve specialised tasks. these blocks are produced in steel, ceramic or carbide, and their material choice balances wear resistance with thermal behaviour. regular calibration—typically performed annually—by DAkkS-accredited laboratories ensures traceability. the highest-precision reference work, class K, is certified by the PTB using laser techniques; classes 0, 1 and 2 are tested under progressively less controlled conditions (class 0 in a climate-controlled lab, class 1 in a standard measurement room, class 2 in production).
measurable benefits that cut downtime and uncertainty
- consistent, traceable length standards reduce rework and measurement disputes by enabling reliable instrument calibration.
- choosing the correct material (steel, ceramic, carbide) extends service life and limits wear in high-use environments.
- selecting the right accuracy class (K, 0, 1 or 2) matches calibration effort to application needs and avoids over‑specification.
- annual calibration by accredited labs maintains documented compliance and supports quality systems such as ISO.
why Metav is a smart partner for precision standards
Metav combines specialist knowledge with a broad range of measurement technology, making the procurement of gauge blocks straightforward and dependable. with over 48,000 customers and more than 250,000 products stocked from Emmerich, Metav acts as a pragmatic quality filter for European workshops, reducing supplier complexity and ensuring consistent supply.
In short, gauge blocks deliver traceable, material‑appropriate and class‑matched references that keep calibration workflows efficient and auditable.
faq
what materials are gauge blocks available in and why does it matter?
gauge blocks are typically supplied in steel, ceramic or carbide. material choice affects wear resistance, stability and thermal expansion; selecting the right material for your environment optimises longevity and measurement stability.
how often should gauge blocks be calibrated?
industry practice is an annual calibration cycle, carried out by DAkkS-accredited laboratories, though frequency can be increased depending on usage and required uncertainty.
what do the accuracy classes k, 0, 1 and 2 indicate?
the classes denote graded tolerances and test conditions: K is the highest precision (certified by PTB with laser measurement), class 0 is checked under climate-controlled lab conditions, class 1 in a normal measurement room and class 2 in production environments.
are parallel gauge blocks always used for length calibration?
yes; for length calibration the parallel gauge blocks are the primary standard because they provide exact planar faces for wringing and stacking to create precise lengths.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com