End gauges for precise length calibration
End gauges provide exact reference lengths for calibrating measurement instruments and ensuring consistent dimensional accuracy in metalworking and inspection processes. Used in production and laboratory settings, these end gauges—made from steel, ceramic or carbide—allow technicians to compensate for wear and thermal effects and maintain measurement traceability, especially when employed alongside parallel end gauges, cylinder gauges and calibration masters. Classes 0, 1 and 2 define practical tolerance levels for workshop, inspection-room and production use respectively, delivering the repeatable precision required for machining and quality control.
1.7 mm Gauge Block, DIN EN ISO 3650 Grade 0, Hardened Special Steel - Metav IndustryLine
Take advantage of Grade 0 reproducibility, the hardened special steel construction and the compact cross‑section for reliable reference measurements in production and the metrology lab — order via Metav Werkzeuge or consult our specialists for application advice. Single gauge block 1.7 mm (DIN EN ISO 3650, Grade 0) — Metav IndustryLine The Single gauge block 1.7 mm (DIN EN ISO 3650 Grade 0) serves as a high‑precision reference standard for calibration, setting and verification tasks in workshops and metrology laboratories. Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel construction Cross-section 30 x 9 mm for compact setup Nominal size 1.7 mm, traceable SKU M319.017.0 Precision that supports repeatable measurement decisions The Grade 0 specification according to DIN EN ISO 3650 defines a narrow tolerance band for this 1.7 mm reference, making it suitable where reproducible nominal values are required. As a compact reference standard, the gauge offers a stable basis for setting micrometric stages, calibrating measuring instruments or checking positional offsets. The direct consequence for production and quality assurance is a reduced uncertainty in downstream measurements and fewer rework loops, supporting leaner inspection processes and predictable tolerances. Durable construction for sustained accuracy Manufactured from special steel and delivered in a hardened state, the block resists wear and maintains geometry under regular handling. The small cross‑section (30 x 9 mm for nominal sizes up to 10 mm) and an overall weight of approximately 0.007 kg allow easy handling and rapid integration into measurement setups without adding excessive mass or inertia. These material and form choices reduce thermal and mechanical distortion during short‑term handling and frequent use, which in turn preserves the accuracy of the reference over many cycles. Practical benefits for bench and laboratory workflows The gauge block’s compact geometry and standardised tolerance class simplify storage in inspection sets and pairing with other blocks for stack‑up configurations. As a standard reference it shortens set‑up times when transferring measurements between instruments and provides a stable reference for comparative checks. Clear traceability via SKU and GTIN supports audit trails and inventory control, while the conformity to recognised standards aids acceptance in supplier and customer audits. How it fits into a quality system Integration of a consistent set of reference blocks like this one ensures that measurement chains remain comparable across shifts and locations. Using a Grade 0 reference helps to align routine checks with calibration plans and enables technical teams to document measurement capability more convincingly. For organisations that prioritise predictable measurement outcomes, the small, hardened block acts as an economical and robust element of a wider metrology strategy. For application guidance or to secure the Metav IndustryLine Grade 0 single gauge block, contact Metav Werkzeuge for tailored advice and ordering support. Technical data Article number: M319.017.0 GTIN: 4054469131184 Standard: DIN EN ISO 3650 Nominal size: 1.7 mm Facts Weight: 0.007 kg Cross-section: 30 x 9 mm (for nominal sizes ≤ 10 mm) Tolerance class: Grade 0 Tariff number: 90173000 Special features Material: Special steel, hardened Category: End gauge (Endmasse) Category path: Messgeräte › Endmasse FAQ What accuracy class does this reference block meet? The Single gauge block 1.7 mm meets Grade 0 according to DIN EN ISO 3650, providing a tight tolerance suitable for reference and calibration tasks. Which material is used and why does it matter? The block is made from special steel, hardened, which combines wear resistance with dimensional stability to preserve the calibrated size during regular use. Is this block suitable for workshop and laboratory use? Yes — the Grade 0 block from Metav IndustryLine is intended for both workshop set‑ups and metrology benches where a compact, repeatable reference of 1.7 mm is required. How is the product identified for traceability? Identification is possible via SKU M319.017.0 and GTIN 4054469131184, which supports stock management and audit trails. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.7 mm Gauge Block, DIN EN ISO 3650 Grade 1, Hardened Special Steel - Metav IndustryLine
Take advantage of the combination of DIN EN ISO 3650 conformity, Grade 1 metrological accuracy and a hardened special‑steel construction for consistent reference measurements; order directly via Metav Werkzeuge or consult our specialists for application advice. End gauge 1.7 mm (DIN EN ISO 3650) — Grade 1 reference gauge by Metav IndustryLine The End gauge 1.7 mm (DIN EN ISO 3650) is a hardened, precision reference gauge intended for high‑accuracy inspection and comparative control in industrial metrology. DIN EN ISO 3650 certified accuracy Grade 1 tolerance for reference measurements Hardened special‑steel construction Compact cross‑section 30×9 mm for up to 10 mm Reliable reference for inspection and setting tools This reference part serves as a compact reference gauge for calibration checks, go/no‑go verifications and setting jigs where a stable, standardised dimension is required. Made from hardened special‑steel, the component resists wear and delivers reproducible contact conditions over many cycles, which reduces setup time and the need for frequent replacement. Conformity to DIN EN ISO 3650 and the Grade 1 classification provide a documented basis for quality control procedures and facilitate traceable acceptance criteria in production and incoming inspection. Practical advantages in the workshop and metrology lab The small nominal size and reduced mass of this gauge make it easy to handle while maintaining rigidity: the cross‑section specified for sizes up to 10 mm is 30×9 mm, giving a stable contact face and minimised bending under normal use. The modest weight supports fast inspections without awkward handling. As a standardised reference, the gauge shortens measurement routines and helps to harmonise pass/fail decisions across shifts and machines, increasing throughput and reducing subjective measurement error. How conformity and material translate into day‑to‑day benefits Compliance with DIN EN ISO 3650 means that tolerance classes and inspection limits are standardised; the Grade 1 designation indicates a high level of manufacturing precision appropriate for demanding quality control tasks. The hardened material resists surface deformation, preserving nominal dimensions and ensuring long service life. For procurement and documentation, the unique identifier M319.017.1 and GTIN are available to support stock control and traceability in certified quality systems. Choose the Metav IndustryLine end gauge for dependable reference measurements and contact Metav Werkzeuge for tailored technical advice — Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich; info@metav-werkzeuge.com; +49 2822 7131930 Technical data SKU: M319.017.1 GTIN: 4054469131191 Label: End gauge 1.7 mm, DIN EN ISO 3650, Grade 1 Facts Nominal size: 1.7 mm Weight: 0.007 kg Cross‑section (≤10 mm): 30×9 mm Tariff number: 90173000 eClass: 21170108 Special features Material: hardened special‑steel Conformity: DIN EN ISO 3650 Tolerance class: Grade 1 Category: End gauges FAQ What is the intended use of this end gauge? The end gauge 1.7 mm (M319.017.1) is intended as a precision reference for inspection, go/no‑go checks and setting of measuring fixtures in industrial metrology. How does Grade 1 affect accuracy? Grade 1 specifies a high manufacturing tolerance within DIN EN ISO 3650; the Grade 1 classification of this end gauge ensures suitability for demanding quality control and reference tasks. What material and hardening are used? The gauge is manufactured from hardened special‑steel, chosen to provide wear resistance and dimensional stability under regular inspection use. Is the cross‑section suitable for small diameters? Yes; the specified cross‑section 30×9 mm applies for gauges up to 10 mm and gives a rigid contact geometry for repeatable measurements. How should the gauge be stored to preserve accuracy? Store the gauge in a clean, dry environment and protect it from shocks and corrosive agents; regular visual inspection will help maintain surface integrity and measurement reliability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.8 mm Gauge Block Grade 1 DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Reliable dimensional control is delivered by combining DIN EN ISO 3650 Grade 1 tolerances with hardened special steel, while the compact 1.8 mm nominal size supports fine-feature verifications; order the End gauge 1.8 mm directly via Metav Werkzeuge or contact our consultants for application advice. End gauge 1.8 mm (DIN EN ISO 3650) — Precision end gauge, hardened special steel, Grade 1 The End gauge 1.8 mm (DIN EN ISO 3650) is a precision reference for dimensional verification and comparative checks in metrology, suited to quality control tasks and workshop calibration benches. Grade 1 accuracy (DIN EN ISO 3650) Hardened special steel construction Nominal size 1.8 mm precision Compact cross-section for small features Measurement certainty for fine components Manufactured to the tolerance class defined in DIN EN ISO 3650, this reference piece provides reproducible dimensional accuracy for inspection tasks where small deviations matter. The hardened special steel body retains geometry under repeated handling and resists surface wear, which keeps the nominal size stable over many measurements. For laboratories and production lines that compare parts against a reference, the combination of a standardised tolerance class and robust material ensures that measurement decisions are technically justified and auditable. Designed for repeatable, ergonomic use The slender cross-section specified for small nominal sizes reduces handling interference when checking narrow bores or tight grooves. The compact cross-section enables secure placement in fixtures and gauges, simplifying alignment during routine control procedures. As a gauge block-style reference, it supports quick comparative checks and fits into existing inspection jigs without elaborate fixturing, reducing measurement time while maintaining traceability to recognised standards. Clear integration into inspection workflows As a Grade 1 reference, this device suits final acceptance checks and in-process control where conformity to DIN EN ISO 3650 is required. Its precise nominal size simplifies documentation: entries such as nominal dimension and standard class map directly into quality reports and inspection plans. The solid construction minimises thermal and mechanical drift during short measurement cycles, which helps to reduce uncertainty and supports clearer go/no-go decisions within standardised quality systems. Contact Metav Werkzeuge in Emmerich to discuss availability, delivery options and suitability of Grade 1 end gauges for specific inspection tasks Technical data Article number: M319.018.1 GTIN: 4054469131214 SKU: M319.018.1 Key measurements Nominal size: 1.8 mm Weight: 0.007 kg Cross-section: up to 10 mm — 30 x 9 mm; from 10.1 mm — 35 x 9 mm Tolerance class: Grade 1 Materials & standards Material: hardened special steel Standard: DIN EN ISO 3650 Tariff number: 90173000 FAQ What tolerance class does this reference conform to? The reference conforms to DIN EN ISO 3650 as a Grade 1 end gauge, offering the tighter tolerances required for precision inspection. Which material is used for the gauge? The piece is manufactured from hardened special steel, chosen to maintain geometry and resist wear during routine use. How is this end gauge typically applied in a workshop? This gauge functions as a reference for comparative checks and small-part verification; it integrates with inspection jigs and supports clear acceptance criteria in quality documentation. What identifiers are available for ordering and traceability? Order and trace using Article number M319.018.1 or GTIN 4054469131214 for unambiguous identification in procurement and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.8 mm Gauge Block Single End, Hardened Special Steel, DIN EN ISO 3650 Grade 0 - Metav IndustryLine
Take advantage of the combination of Grade 0 accuracy, hardened special steel construction and a compact cross-section for reliable reference measurements in inspection and workshop environments; order the Single gauge block 1.8 mm directly via Metav Werkzeuge or contact our consultants for advice. Single gauge block 1.8 mm — hardened special steel, DIN EN ISO 3650 Grade 0 A Single gauge block 1.8 mm designed as a high-precision length standard for calibration, inspection and reference tasks in toolrooms and metrology laboratories. DIN EN ISO 3650 grade 0 accuracy Hardened special steel construction Compact cross-section: 30×9 mm Nominal length 1.8 mm for micro gauging Consistent, traceable reference for precise length checks The Single gauge block 1.8 mm fulfils the requirements of DIN EN ISO 3650, offering a stable reference for fine length verification and comparative checks. Compliance with the standard ensures reproducible behaviour across measurement chains, which directly supports quality control processes. The Grade 0 classification indicates a high level of dimensional fidelity suitable for demanding inspection tasks where repeatability and conformity are required. Robust construction for reliable day-to-day use Manufactured from hardened special steel, this end gauge gives a wear‑resistant contact surface that withstands routine handling in workshops and inspection benches. The compact 30×9 mm cross-section (applicable for nominal lengths up to 10 mm) keeps the block rigid and easy to seat in holders or between reference faces. Low mass and a precise rectangular profile facilitate rapid stacking and combination with other blocks when creating gauge sets. Practical role in calibration and assembly workflows As a single length standard, the block serves as a quick verification tool for micrometric instruments and gauges, and as a building element within a gauge block set for setting up master lengths. The modest nominal size makes it especially useful for micro gauging tasks, fine mechanical assembly checks and instrument calibration where short reference lengths are required. Using a standardised block reduces measurement uncertainty in routine comparative tests. Handling, identification and procurement At 0.007 kg and with a clearly defined cross-section, the block is simple to handle and store in protective cases or drawers appropriate for precision tools. Clear identification via SKU and GTIN supports inventory control and traceability in procurement processes. For customers seeking an established supply chain, Metav IndustryLine provides a consistent product range and logistical support suited to industrial and laboratory environments. Select the Metav IndustryLine single gauge block 1.8 mm as a dependable reference length and contact Metav Werkzeuge for procurement or technical consultation at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M319.018.0 GTIN: 4054469131207 Tariff number: 90173000 Core specifications Nominal length: 1.8 mm Weight: 0.007 kg Cross-section (≤10 mm): 30×9 mm Special features Material: hardened special steel Standard: DIN EN ISO 3650 Grade: 0 Category: End gauge FAQ What accuracy class does this gauge meet? The Single gauge block 1.8 mm conforms to DIN EN ISO 3650, grade 0, which denotes a high accuracy class suitable for precision reference use. What material is the block made from and why does that matter? This end gauge is produced from hardened special steel, giving wear resistance and a stable contact surface that maintains dimensional integrity under regular use. Can the block be used with other gauge blocks to build master lengths? Yes, the block is intended as a modular length standard and can be combined with other gauge blocks to create required master lengths for calibration and setup tasks. How should the Single gauge block 1.8 mm be stored to preserve accuracy? Store the block in a clean, dry environment in dedicated protective packaging or drawer systems designed for precision tools to avoid surface damage and contamination. Is the product suitable for workshop and laboratory use? The Metav IndustryLine single gauge block 1.8 mm is designed for both workshop verification and laboratory reference tasks, offering Grade 0 conformity for consistent measurement routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.8mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of a ceramic construction, Grade 1 accuracy and a compact 1.8 mm nominal size for repeatable reference measurements; order the gauge directly via Metav Werkzeuge or consult our technical advisors for integration into existing calibration routines. Ceramic gauge block 1.8 mm, Grade 1 DIN 861/1 — End gauge from Metav IndustryLine The Ceramic gauge block 1.8 mm, Grade 1 DIN 861/1 serves as a compact precision reference for calibration tasks and dimensional inspection across quality control and metrology applications. Ceramic material for thermal stability Grade 1 accuracy to DIN 861/1 Reference gauge block for calibration Nominal size 1.8 mm, compact and lightweight Reliable reference for routine calibration and inspection The Ceramic gauge block 1.8 mm, Grade 1 DIN 861/1 is designed as a stable reference element for routine checks in inspection benches and calibration workflows. With Grade 1 conformity to DIN 861/1, it provides a predictable baseline for calibration activities and helps reduce measurement scatter when used as part of a gauge set. The small nominal size makes the block easy to handle and position in tight setups, while the compact footprint minimises the influence of external alignment errors during comparison measurements. Material advantages that support measurement stability Made from ceramic, the block offers inherent benefits that contribute to consistent measuring results: low coefficient of thermal expansion, excellent wear resistance and chemical inertness compared with many metallic alternatives. These material properties support dimensional constancy under typical workshop and laboratory conditions, improving the long‑term reliability of a reference inventory. Where ambient temperature control is limited, the reduced sensitivity of ceramic to short‑term fluctuations helps maintain reproducible readings during comparative procedures. How this reference element fits into metrology workflows As a precise end gauge, this specimen complements existing gauge block sets and wringing procedures used in dimensional metrology. Its 1.8 mm nominal size provides an intermediate reference for calibrations, comparison measurements and fixture checks; when integrated into a traceable programme it strengthens traceability chains and simplifies routine verification tasks. The compact mass and geometry also allow for quick exchanges on comparator tables or when stacking with other blocks during step measurements. Procurement confidence and quality assurance from Metav Sourcing this end standard from the Metav IndustryLine provides the backing of a supplier that combines broad product availability with a local European quality filter. Metav’s positioning as a precision partner ensures consistency in delivery and the opportunity to harmonise this reference component with wider workshop equipment and service offerings. The combination of technical conformity and trusted sourcing removes uncertainty from routine acquisitions and supports documented quality systems in manufacturing and inspection environments. For secure supply and specification advice on the Metav IndustryLine ceramic gauge block, contact Metav Werkzeuge in Emmerich by email or phone for direct assistance and local delivery: info@metav-werkzeuge.com, +49 2822 7131930 Technical Data SKU: M324.001.8 GTIN: 4054469142906 Material: Ceramic Nominal size: 1.8 mm Grade: 1 (DIN 861/1) Weight: 0.004 kg Tariff number: 90173000 eClass: 21170108 Facts Nominal length: 1.8 mm Mass: 0.004 kg GTIN numeric identifier: 4054469142906 Tariff heading: 90173000 Classification: eClass 21170108 Special features Material: Ceramic Accuracy class: Grade 1 according to DIN 861/1 Product category: End gauge / gauge block (Endmasse) Asset image available for reference FAQ What is the intended use of this gauge block? The Ceramic gauge block 1.8 mm, Grade 1 DIN 861/1 is intended as a precision reference for dimensional verification, calibration checks and inspection tasks in quality control environments. Which accuracy class does this reference meet? This reference meets Grade 1 requirements according to DIN 861/1, making it suitable for standard laboratory reference use and routine calibration checks. What material and identifiers apply to the product? The Ceramic gauge block 1.8 mm, Grade 1 DIN 861/1 (SKU M324.001.8, Metav IndustryLine) is manufactured from ceramic and carries GTIN 4054469142906. How should the block be cleaned and stored? Handle the Ceramic gauge block 1.8 mm, Grade 1 DIN 861/1 with care; store in a dry, temperature‑stable environment and clean with lint‑free cloths and approved solvents to avoid contamination or surface damage. Is this gauge block compatible with standard gauge block sets and wrings? Yes, the 1.8 mm reference is compatible with standard wringing and stacking procedures and can be integrated into existing gauge block sets for comparison and step measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.9 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of Grade 1 accuracy, wear‑resistant ceramic construction and a compact 1.9 mm nominal size for highly repeatable reference measurements. Order the Ceramic gauge block directly via Metav Werkzeuge or ask our consultants if needed. Ceramic gauge block 1.9 mm, Grade 1 (DIN 861/1) — Metav IndustryLine Ceramic gauge block 1.9 mm, Grade 1 (DIN 861/1) offers a stable reference standard for precision measurement in workshop and laboratory environments, suitable for high‑repeatability tasks and calibration sets. *Grade 1 tolerance for metrology applications *Stable, wear‑resistant ceramic material *Nominal size 1.9 mm for fine comparisons *Conforms to DIN 861/1 measurement standards Precision where repeatability matters The ceramic construction provides a stable measurement reference with minimal thermal expansion compared with common steels, reducing dimensional drift during short inspection routines. As a gauge block with Grade 1 tolerance, it serves as a fine reference for setting and checking micrometre and caliper standards; the small 1.9 mm nominal size makes it particularly useful when calibrating fine measuring devices or assembling precision gauge sets. The result is consistent, verifiable measurements that support quality control processes. Durable material for long service life Made from advanced ceramic, this block combines wear resistance with a low coefficient of thermal expansion, which helps maintain nominal size under normal shop conditions. The hardness of the material resists surface degradation from repeated wringing and handling, so calibration intervals can be extended in many routine uses. The material choice therefore translates directly into lower maintenance overhead and more stable reference values for daily inspection work. Practical handling and application benefits The compact dimensions and low weight make this block easy to integrate into an existing set of reference pieces or to carry in a secure pouch for field checks. When used together with a calibrated set, it supports traceable verification of measuring instruments and aids fast decision making in production and incoming‑goods inspection. Clear conformity to DIN 861/1 ensures interchangeability within standardised gauge sets, facilitating smooth workflows across different workstations and inspection benches. Contact Metav Werkzeuge today to discuss availability of the Ceramic gauge block, calibration options and delivery from Emmerich — our consultants will advise on the best configuration for the specific metrology task. Technical Data Article number: M324.001.9 GTIN: 4054469142913 Tariff number: 90173000 Facts Nominal size: 1.9 mm Weight: 0.004 kg Tolerance grade: 1 Special features Material: Ceramic Standard: DIN 861/1 Category: Gauge blocks / End measures FAQ What is the main advantage of a ceramic gauge block compared with steel? Ceramic gauge blocks offer lower thermal expansion and improved wear resistance; the Ceramic gauge block 1.9 mm, Grade 1 (DIN 861/1) therefore delivers more stable reference values under typical workshop temperature variations. Is this block suitable for calibration sets and traceable measurements? Yes. The Grade 1 tolerance and conformity with DIN 861/1 make this block suitable for inclusion in calibration sets and for traceable comparative measurements in routine quality control. How should the block be handled to maintain accuracy? Handle the block with clean gloves or tweezers and keep it free from contamination; the ceramic surface is hard and wear‑resistant, but correct wringing technique and careful storage preserve its reference condition. Can this item be used for setting micrometres and precision calipers? Yes. Its compact 1.9 mm nominal size is suitable for fine setting tasks and for verifying the lower range of micrometres and precision calipers. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.9 mm Gauge Block Grade 1 DIN EN ISO 3650 Hardened Special Steel - Metav IndustryLine
Take advantage of a compact reference standard that combines DIN EN ISO 3650 Grade 1 accuracy with a hardened special steel construction and a slim cross‑section for straightforward handling; order the gauge direct via Metav Werkzeuge or consult our specialists for integration into calibration or inspection workflows. End gauge 1.9 mm (DIN EN ISO 3650) — Grade 1, hardened special steel — Metav IndustryLine The End gauge 1.9 mm is a precision reference for dimensional checks and calibration tasks in metrology workshops and inspection benches. Grade 1 tolerance to DIN EN ISO 3650 Hardened special steel construction Nominal size 1.9 mm for reference checks Compact 30 x 9 mm cross-section for easy handling Reliable reference for inspection and calibration Manufactured to DIN EN ISO 3650 with Grade 1 tolerance, this compact end gauge provides a stable, verifiable reference dimension of 1.9 mm for shop‑floor checks and laboratory routines. As a hard reference piece, it supports repeatable comparative measurements when setting micrometers, verifiers or comparator setups, reducing uncertainty in routine quality control. The normative designation signals compatibility with standardised inspection procedures and facilitates traceable documentation in quality records. Durable, consistent construction that eases handling The body is made from hardened special steel, offering high wear resistance and long service life even under frequent contact with other calibrated instruments. The slim 30 x 9 mm cross‑section (applies to nominal sizes up to 10 mm) gives a favourable stiffness‑to‑weight ratio and supports precise seating on reference surfaces, while the low mass keeps handling nimble. This combination of material and form reduces thermal drift and mechanical deformation during short handling times, making the gauge suitable for both bench use and integration into gauge sets. Practical uses and workshop integration Designed for industrial metrology and scales, the block serves as a straightforward reference for dimensional checks, setting fixed gauges and verifying measuring instruments. The compact format fits conveniently in standard gauge trays and works with common calibration jigs. With clear specification and industry standard compliance, the piece supports efficient inspection routines and helps maintain consistent production quality when used alongside other traceable standards supplied by Metav IndustryLine. For assured dimensional control and smooth integration into existing quality systems, contact Metav Werkzeuge in Emmerich for ordering or technical advice — info@metav-werkzeuge.com • +49 2822 7131930 — Metav IndustryLine stocks and supplies precision references for immediate use. Technical data Article number: M319.019.1 GTIN: 4054469131238 Label: End gauge 1.9 mm, DIN EN ISO 3650, Grade 1 Category: End gauges Facts Nominal dimension: 1.9 mm Weight: 0.007 kg Cross‑section (≤ 10 mm): 30 x 9 mm Tariff number: 90173000 Design and special features Material: hardened special steel Standard: DIN EN ISO 3650 (Grade 1) Intended use: reference measurement and inspection Manufacturer brand: Metav IndustryLine FAQ What tolerance class does this gauge meet? The End gauge 1.9 mm is made to DIN EN ISO 3650 and specified as Grade 1, providing a recognised tolerance level for routine reference work. Is the material suitable for regular workshop use? Yes, the End gauge 1.9 mm is manufactured from hardened special steel, chosen for wear resistance and dimensional stability under normal workshop handling. What are the typical applications for this gauge? Typical uses include setting and checking micrometers, verifying comparator settings and serving as a small reference standard in inspection benches; the format is optimised for workshop and laboratory routines. How should the gauge be stored to preserve accuracy? Store the End gauge 1.9 mm in a clean, dry environment away from direct heat sources and heavy vibration; use a dedicated tray or protective pouch to prevent contact damage between reference pieces. Can this gauge be integrated into a set of reference standards? Yes, the compact form and standard compliance of the End gauge 1.9 mm make it suitable for inclusion in gauge sets and for routine comparative checks as part of a documented quality system. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.9 mm Gauge Block Single End, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of DIN EN ISO 3650 Grade 0 conformity and a hardened special steel construction for a compact, reliable reference standard; order this gauge directly via Metav Werkzeuge or consult our specialists for application advice. Single end gauge 1.9 mm — Grade 0 end gauge, hardened special steel (Metav IndustryLine) Single end gauge 1.9 mm is a precision reference measure for laboratory and workshop calibration tasks, designed for dimensional control and gauge set assembly DIN EN ISO 3650 Grade 0 accuracy Hardened special steel construction Nominal size 1.9 mm for fine reference Compact cross-section 30x9 mm profile Consistent laboratory-grade accuracy for routine calibration This single end gauge is manufactured to DIN EN ISO 3650 and specified as Grade 0, providing a stable reference for dimensional inspection and comparative checking. As a standardised end measure with a nominal size of 1.9 mm, the gauge delivers a defined tolerance band that supports repeatable set-ups on micrometre stands, comparator fixtures and within gauge blocks assemblies. The measured tolerance class simplifies conformity assessments and reduces uncertainty when establishing reference stacks or verifying small-feature geometries. Robust material choice for long-term stability and wear resistance Constructed from hardened special steel, the gauge combines surface durability with dimensional stability under normal workshop conditions. The compact cross-section (30x9 mm for nominal sizes below 10 mm) minimises bending and thermal gradients, which helps maintain the calibrated state during handling and short-term use. Weighing approximately 0.007 kg, the component is light enough for easy positioning yet rigid enough to serve as a reliable reference in repeated measurement cycles. Practical integration into inspection workflows and documentation The plain geometry and standardised form factor make this reference ideal for inclusion in precision sets and for establishing small reference stacks in production sampling routines. Labelling with GTIN and article identifiers enables traceable inventory control, while the physical format suits both bench-top inspection and fixture-based checks. When used alongside stable measurement procedures, the end gauge supports rapid, rational decision-making in quality control by offering a clear, verifiable standard. For precise reference needs from the Metav IndustryLine range, contact Metav Werkzeuge for product availability and tailored advice — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M319.019.0 GTIN: 4054469131221 Category: End gauges ECLASS: 21170108 Core specifications Nominal size: 1.9 mm Weight: 0.007 kg Cross-section (for ≤10 mm): 30 x 9 mm Tariff number: 90173000 Materials & special features Hardened special steel Conforms to DIN EN ISO 3650 Grade 0 tolerance class Compact form for small-feature reference FAQ What tolerance class does this gauge provide? The single end gauge 1.9 mm is specified as Grade 0 according to DIN EN ISO 3650, offering a well-defined tolerance suitable for laboratory and workshop reference tasks. Is the gauge suitable for use as a reference in gauge blocks or stacks? Yes, the form and finish of this end gauge allow it to be integrated into small reference stacks and comparative set-ups for dimensional verification. What material is the gauge made from and how does that affect durability? Manufactured from hardened special steel, the gauge combines wear resistance with dimensional stability, which supports longevity under normal handling and routine inspection use. Does the product include an official calibration certificate? The product data does not indicate an ISO 17025 calibration certificate; conformity is provided by manufacture to DIN EN ISO 3650 Grade 0. For laboratory-grade traceable calibration requests, please contact Metav Werkzeuge. Can this gauge be used for automated measuring machines or only manual checks? The compact geometry and standardised dimensions make the gauge suitable primarily for manual and fixture-based checks; compatibility with automated systems depends on the specific machine interfaces and handling processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1/4°–30° Angle Gauge Set 12Pc Aged Hardened Special Steel, Supplied In Case - Metav IndustryLine
Take advantage of a robust, hardened special steel construction combined with a 12-piece angular range from 1/4° to 30° for consistent set-up and inspection in jigs and fixtures; order or consult via Metav Werkzeuge for rapid supply and technical advice. Angle end gauge set M318.215 — 12-piece hardened special steel, 1/4°–30° (Metav IndustryLine) The Angle end gauge set M318.215 is a compact suite of precision angle gauges designed for setting, checking and calibrating angular positions across workshop and metrology tasks. 12-piece angle set from 1/4° to 30° Hardened special steel construction Precision tolerance 0.01 for repeatable setups Compact 76 mm length, 6.35 mm thickness Reliable precision for repeatable angular set-ups The set delivers repeatable positioning through a consistent 0.01 tolerance, making it suitable for tasks where angular accuracy directly affects assembly or machining quality. Each gauge is made from hardened special steel, which sustains close contact with fixtures and maintains edge integrity during frequent use. In practice, this means fewer setup iterations and predictable results when aligning saws, milling heads or rotary fixtures — a measurable efficiency gain for production and maintenance routines. Robust construction that withstands workshop use Aged and hardened steel gives the gauges a combination of wear resistance and dimensional stability. The surface treatment and hardening process reduce the risk of deformation during handling and clamping, so the set keeps calibration over longer service intervals. For workshops that rely on consistent jigs or repeat inspections, this durability reduces rework and tool replacement frequency, supporting continuous operations and lowering lifetime costs without compromising measurement reliability. Compact format for flexible handling and fast access Each blade measures 76 mm in length with a thickness of 6.35 mm, providing a compact profile that is easy to position inside tight assemblies and small envelopes. The modest size enables rapid stacking or insertion into angle seats while preserving sufficient stiffness for accurate contact. The 12-piece configuration covers a broad practical range — from fine adjustments at 1/4° to coarse settings at 30° — so a single kit replaces multiple bespoke gauges, simplifying tool management on the shop floor. Clear benefits for quality control and setup workflows Delivered as a complete set, these angle gauges support faster setup times and more consistent quality checks during production changeovers. The set’s measured accuracy and robust material choice help reduce measurement scatter and give inspection staff a dependable reference for angular verification. For engineering teams, the ability to rely on repeatable gauge values shortens diagnostics and aligns assembly tolerances more tightly to specification. For tailored technical advice or to secure prompt delivery of the M318.215 angle end gauge set from Metav IndustryLine, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for direct assistance from Emmerich. Technical data Article number: M318.215 GTIN: 4054469128153 eClass: 21170110 Tariff number: 90173000 Numbers / Core technical data Pieces per set: 12 Angle range: 1/4°; 1/2°; 1°; 2°; 3°; 4°; 5°; 10°; 15°; 20°; 25°; 30° Length: 76 mm Thickness: 6.35 mm Weight: 1 kg Accuracy/tolerance: 0.01 Designs / Special features Material: Special steel, aged and hardened Set format for workshop and metrology use Compact blades for confined spaces FAQ What angles are included in the set? The set contains twelve angles: 1/4°, 1/2°, 1°, 2°, 3°, 4°, 5°, 10°, 15°, 20°, 25° and 30°, supplied as a complete 12-piece kit. What tolerance can be expected from these gauges? The gauges are specified with a precision tolerance of 0.01, suitable for accurate setup and repeatable angular checking in workshop environments. Which material is used for the gauges? The gauges are manufactured from special steel, aged and hardened, providing wear resistance and dimensional stability for frequent use. Is this set suitable for fixture alignment and machine set-up? Yes, the compact 76 mm blades and hardened construction make the set appropriate for fixture alignment, tool setup and routine angular verification tasks. How is the M318.215 supplied for immediate use? The M318.215 is supplied as a complete 12-piece angle end gauge set, ready for integration into setup and inspection workflows. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
The combination of Grade 1 accuracy (DIN 861/1), a 10 mm nominal length and a ceramic construction delivers a stable reference standard for routine length checks and calibration tasks in the workshop or metrology lab. Order the ceramic gauge block directly via Metav Werkzeuge or ask our consultants if needed. Ceramic gauge block 10 mm — Grade 1 (DIN 861/1) by Metav IndustryLine Ceramic gauge block 10 mm, Grade 1 (DIN 861/1) offers a compact, high-stability reference for length measurement and inspection tasks in industrial and calibration environments Grade 1 accuracy (DIN 861/1) Ceramic material for thermal stability Nominal length 10 mm reference Lightweight: 16 g for easy handling Reliable Grade 1 length reference for everyday metrology As a Grade 1 length standard certified by the DIN 861/1 specification, this 10 mm ceramic reference is intended for repeatable comparative measurements and machine calibration. The narrow nominal size makes it particularly useful where compact, unambiguous reference lengths are required. The conformity with DIN 861/1 signals an established tolerance class and helps to harmonise inspection routines across production and quality control workflows. Use as a reference element reduces uncertainty in routine checks and supports consistent decision-making in component acceptance. Stable ceramic construction that supports dimensional consistency Manufactured from ceramic, the block is designed for dimensional stability under normal workshop temperature variations and avoids common issues associated with metal corrosion. The material choice contributes to low thermal expansion, which helps maintain the reference length during short-term ambient changes. The compact mass—approximately 0.016 kg—also aids quick handling during set-up and transfer between instruments. In practical terms, the ceramic build benefits labs and production lines that require reliable, low-maintenance reference standards without frequent correction. Practical use and integration into inspection routines This reference element serves as a straightforward length benchmark for dial gauges, height gauges and comparators, and is suited to routine calibration work where a fixed 10 mm reference is needed. The compact format simplifies storage in instrument cases and rapid deployment at inspection stations. Traceability and formal calibration status are not specified in the provided product data; however, the item’s designation and grade make it appropriate as a workshop reference or as part of a set of gauge blocks for comparative procedures. For inventory and documentation purposes, the article is listed under SKU M324.010 and carries GTIN 4054469143088. For technical guidance on incorporating Grade 1 ceramic gauge blocks into quality processes or to confirm suitability for a specific measuring task, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 and request further specification or procurement advice. Technical data Article number: M324.010 GTIN: 4054469143088 Material: Ceramic Nominal length: 10 mm Grade: 1 (DIN 861/1) Weight: 0.016 kg Tariff code: 90173000 Numbers / Core technical data Nominal length: 10 mm Weight: 0.016 kg Grade: 1 Tariff code: 90173000 Special features Ceramic construction Compliance: DIN 861/1 (Grade 1) Category: End gauges Compact, low-mass reference FAQ What tolerance class does this gauge block meet? The product is specified as Grade 1 according to DIN 861/1, indicating its tolerance class for use as a reference length. Is the gauge block made of metal or ceramic? This reference is manufactured from ceramic; the material is noted for dimensional stability under typical ambient conditions. What is the nominal length and mass of the block? The nominal length is 10 mm and the mass is approximately 0.016 kg, as listed under SKU M324.010. Is an ISO 17025 calibration certificate included? The product data does not indicate an ISO 17025 calibration certificate or a specific calibration status for this item. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10 mm Gauge Block Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of a DIN EN ISO 3650 Grade 1 reference delivered in hardened special steel for consistent inspection results; the compact 10 mm nominal length and slim cross‑section support easy handling and repeatable comparator checks. Order this precision end gauge directly via Metav Werkzeuge or consult the specialist team for procurement guidance. End gauge 10 mm (DIN EN ISO 3650) — Grade 1, hardened special steel — Metav IndustryLine The End gauge 10 mm is a compact, high‑precision reference standard intended for dimensional inspection, comparator set‑up and laboratory checks in machine shops and quality departments. Grade 1 accuracy per DIN EN ISO 3650 Hardened special steel construction Nominal length 10 mm for reference checks Compact cross-section 30 x 9 mm for easy handling Consistent results with a recognised length standard Manufactured to DIN EN ISO 3650 and classified as Grade 1, this 10 mm reference block offers a stable benchmark for routine inspection and instrument setting. The short nominal length makes it suitable for use as a reference on comparators, in gauge sets and for quick verification of micrometers and callipers. The combination of standard conformity and a small form factor reduces handling time while maintaining a reliable reference surface for repeatable measurements. Durable build that preserves accuracy over time The block is produced from hardened special steel, a choice that balances wear resistance and dimensional stability. With a compact 30 x 9 mm cross‑section for sizes up to 10 mm, the geometry keeps the centre of mass close and minimises the risk of bending or accidental damage during handling. These material and design decisions lower long‑term maintenance needs and ensure that surface quality and nominal length remain consistent across frequent use cycles. Practical integration into shop and lab routines Traceability and straightforward inventory management are supported by clear identifiers (SKU and GTIN) and a tariff classification for customs handling. The block functions as a straightforward reference when establishing measurement chains or performing daily checks in production and inspection environments. Backed by Metav’s broad product range and procurement experience, the component can be integrated into a central quality workflow without complex adjustments. For procurement and expert advice on Metav IndustryLine reference standards, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com or call +49 2822 7131930 to arrange supply and documentation Technical Data SKU: M319.100.1 GTIN: 4054469131573 Tariff number: 90173000 Nominal length: 10 mm Weight: 0.011 kg Material: Special steel, hardened Standard: DIN EN ISO 3650 Grade: 1 Cross-section (up to 10 mm): 30 x 9 mm Category: Endmasse Facts Nominal size: 10 mm Cross-section: 30 x 9 mm Weight: 0.011 kg Grade: 1 Standard: DIN EN ISO 3650 Special features Hardened special steel for wear resistance Compact geometry for comparator and lab use Suitable as a workshop reference standard GTIN and SKU for traceability FAQ What does Grade 1 mean for this end gauge? Grade 1 denotes the block meets the tolerances and surface requirements specified in DIN EN ISO 3650 for a high‑precision reference suitable for laboratory and inspection use. Is the material suitable for regular workshop handling? Yes — the hardened special steel construction provides good wear resistance and stability, making the 10 mm block appropriate for routine comparator checks and setting tasks. What are the block’s dimensions and cross‑section? The nominal length is 10 mm and, for sizes up to 10 mm, the cross‑section is 30 x 9 mm, providing a slim, easy‑to‑handle profile. Which applications are typical for this reference block? The block is intended for dimensional inspection, comparator set‑up, verification of micrometers and callipers, and any application requiring a traceable, short reference length. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10 mm Gauge Block Set For Caliper Verification, 9-Piece, Grade 2, Plastic Case - Metav IndustryLine
Benefit from a robust combination of hardened special steel, recognised standard conformity and a compact nine-piece format for reliable caliper verification; order directly via Metav Werkzeuge or consult our specialists for tailored advice. M318.205 Gauge block set (9-piece) – Grade 2, hardened special steel (Metav IndustryLine) A M318.205 gauge block set engineered for precise verification of calipers and routine dimensional checks in workshop and quality‑control environments Grade 2 accuracy per recognised standards Conforms to DIN EN ISO 3650 and VDI/VDE/DGQ 2618 Hardened aged special steel construction Compact nine-piece set for workshop checks Ensure calipers measure as intended and reduce rejects A calibrated bench routine starts with reliable reference standards. This gauge block set provides a practical solution for comparative checks and routine verification of calipers, allowing consistent confirmation of measuring performance before critical operations. The Grade 2 tolerance class supports regular workshop control tasks by balancing achievable precision with robustness, which helps to reduce measurement-related rework and production delays. Durable construction for repeatability and low maintenance Made from hardened special steel, the blocks are designed to resist wear and maintain surface integrity under frequent handling. The material is aged and hardened to improve dimensional stability and surface hardness, so that repeatability is retained over many cycles of use. That durability translates into lower lifetime cost for standard quality regimes, since fewer replacements and less frequent resurfaces are required. Standards-based accuracy that supports traceable checking Manufactured in line with DIN EN ISO 3650 and VDI/VDE/DGQ 2618, the set meets established industry norms for gauge blocks used in verification and inspection. Conformity to these standards gives a clear, rational basis for acceptance within internal QA procedures and third‑party audits. The specification supports comparative calibration workflows and ensures the set integrates smoothly into documented measurement systems. Practical format for everyday quality control The compact, nine-piece arrangement covers the most common verification lengths encountered in workshop metrology and quality control, offering an efficient sampling range without unnecessary bulk. At approximately 2 kg, the set is straightforward to handle at the bench and convenient for secure storage. The design supports quick selection and pairing with calipers or other dimensional instruments, streamlining routine checks and saving operator time. For supply, specification advice and to source the M318.205 gauge block set from Metav IndustryLine, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or +49 2822 7131930 for expert guidance and dependable delivery. Technical data Article number: M318.205 GTIN: 4054469128054 Manufacturer: Metav IndustryLine Category: Gauge blocks Facts Weight: 2 kg Pieces per set: 9 Grade: 2 Tariff number: 90173000 Special features Material: special steel, aged and hardened Application: verification of calipers and dimensional checks Standards: DIN EN ISO 3650; VDI/VDE/DGQ 2618 Set type: nine-piece gauge block set FAQ What is the primary use of this set? The M318.205 gauge block set from Metav IndustryLine is intended for verification of calipers and routine dimensional checks in workshops and quality‑control laboratories. Which standards does the set comply with? The set is produced to the requirements of DIN EN ISO 3650 and VDI/VDE/DGQ 2618, ensuring suitability for recognised verification procedures. What material are the blocks made from? Blocks are manufactured from special steel that has been aged and hardened to provide wear resistance and dimensional stability under repeated use. Is the set suitable for everyday workshop quality control? Yes; the Grade 2 accuracy and compact nine‑piece format make the set well suited for routine workshop checks and comparative calibration tasks. How should the blocks be handled to maintain accuracy? Handle gauge blocks with clean, dry hands or gloves, avoid impacts, keep mating surfaces free from debris, and store the set in its protective packaging when not in use to preserve surface condition. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10 mm Gauge Block, Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of a certified high‑precision reference with DIN EN ISO 3650 Grade 0 accuracy and a compact 10 mm nominal length in hardened special steel; the small cross‑section provides excellent stability for fine‑scale checks. Order the gauge directly via Metav Werkzeuge or consult our experts for application advice. End Gauge 10 mm (Gauge Block) — DIN EN ISO 3650, Grade 0, Metav IndustryLine End Gauge 10 mm (gauge block) for accurate length reference in calibration, inspection and precision assembly tasks. DIN EN ISO 3650 grade 0 tolerance Hardened special steel construction Nominal length 10 mm, high stability Compact cross-section 30×9 mm for small parts Accuracy that supports reliable decisions on the shop floor This gauge block is manufactured to DIN EN ISO 3650 and delivered as a Grade 0 reference, providing a stable baseline for comparative measurements and setup tasks. The combination of a precisely ground 10 mm nominal length and the fine tolerance class reduces uncertainty in dimensional checks, which in turn shortens setup time and lowers scrap rates. By choosing a standardised reference, calibration chains remain consistent across tools and shifts, supporting reproducible quality control without specialised interpretation. Robust construction for repeated workshop use Built from hardened special steel, the block resists wear under regular contact and preserves its reference dimensions over many inspection cycles. The compact cross‑section 30×9 mm (applicable to the ≤10 mm variant) gives a favourable stiffness‑to‑weight ratio, which helps retain alignment during handling and when stacked with other standards. The modest mass and compact geometry make this end standard convenient to incorporate into assembly jigs, portable check fixtures and comparison benches where larger blocks would be cumbersome. Practical benefits for measurement and process efficiency A high‑quality gauge block of this class assists in reducing the number of measurement steps required for routine verification: it serves as a direct length reference, supports quick visual checks and accelerates instrument verification, thereby increasing throughput in inspection loops. The straightforward geometry simplifies seating and repeatable placement, while the industrial finish minimises surface contamination risks. Where prompt pass/fail decisions are needed, the block’s stability translates into time saved and fewer marginal calls. Integration and long‑term reliability in production chains Due to the adherence to international standards, this reference fits into established calibration strategies and traceability schemes. When used alongside calibrated instruments, the block helps maintain consistent tolerances across production batches. Metav IndustryLine’s offering is tailored for workshops and quality labs that require a compact, robust reference for everyday checks — a pragmatic alternative to bulkier standards while maintaining professional accuracy and longevity. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine 10 mm end gauge (SKU M319.100.0) can be integrated into existing quality workflows and to receive tailored advice from our Emmerich team Technical data Article number: M319.100.0 GTIN: 4054469131566 Nominal length: 10 mm Standard: DIN EN ISO 3650 Material: Special steel, hardened Quality grade: 0 Weight: 0.011 kg Core technical data Cross-section: 30×9 mm (for ≤10 mm variant) Category: End gauges Tariff number: 90173000 Label: Einzel-Endmaß 10 mm, DIN ISO 3650, Güte 0 DIN ISO 3650 Special features Precision ground faces Suitable for calibration and comparison checks Compact format for fine parts inspection Metav IndustryLine product family FAQ What tolerance can be expected from this gauge block? The Metav IndustryLine end gauge is manufactured to DIN EN ISO 3650 and supplied as Grade 0, offering the tight tolerance expected of a Grade 0 reference for reliable comparative measurements. Which material is used for the gauge and why? The block is made from hardened special steel, chosen for its wear resistance and dimensional stability under normal workshop handling and repeated contact. Is this block suitable for bench and portable inspection tasks? Yes, the compact 30×9 mm cross‑section for the ≤10 mm variant and the light weight (0.011 kg) make it convenient for both bench‑based fixtures and portable check routines. Can this gauge be used as a master in a calibration routine? As a DIN EN ISO 3650 Grade 0 reference, it is appropriate for many calibration chains and comparative checks, serving as a dependable master for routine verifications in workshops and small labs. What is the product SKU for ordering or referencing? The item is listed under SKU M319.100.0, GTIN 4054469131566, and belongs to the End Gauges category. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.3mm Gauge Block For Micrometer Verification, DIN EN ISO 3650/1 - Metav IndustryLine
Take advantage of a traceable 10.3 mm reference standard manufactured to recognised norms and a robust special‑steel construction for stable, repeatable micrometer checks; order or request advice directly via Metav Werkzeuge to integrate this gauge into the calibration routine. End gauge for micrometer testing, 10.3 mm — reference standard (DIN EN ISO 3650/1) by Metav IndustryLine End gauge for micrometer testing, 10.3 mm is a compact calibration standard designed for quick verification of micrometer accuracy in workshop and inspection settings DIN EN ISO 3650/1 compliant test standard Nominal size 10.3 mm for micrometer checks Crafted from special steel for dimensional stability Manufacturer SKU M318.203.3 for traceability Precision where it matters: steady reference for micrometer checks The 10.3 mm reference standard serves as a simple yet accurate means to verify the zero and span behaviour of mechanical and digital micrometers. Manufactured to DIN EN ISO 3650/1, the gauge provides a defined nominal dimension for comparison, reducing uncertainty during routine checks. The compact geometry and measured mass ensure minimal thermal drift during short handling periods, while the ground faces guarantee a reproducible contact surface. This makes the standard suitable for both bench checks and as a quick verification tool in production environments. Practical advantages: faster calibration cycles and reliable inspection data Using a dedicated calibration standard shortens verification time and supports consistent inspection outcomes. The reference piece is intended for straightforward insertion between micrometer anvils, enabling immediate detection of wear or misadjustment without complex fixtures. As a hardened component crafted from special steel, it withstands regular handling and maintains its dimensional integrity, helping to reduce measurement variation and machine downtime. The compact size and modest weight support easy storage and ponctual on‑line verification during quality checks. Confidence and supply chain clarity from a dedicated metrology partner Sourcing a standard from a specialist line like Metav IndustryLine adds a layer of procurement reliability: product identity is clear via SKU M318.203.3 and GTIN, and manufacturing to recognised norms underpins trust in repeatability. For workshops and inspection labs aiming to harmonise routine checks across multiple benches, this gauge represents a pragmatic investment in measurement assurance. Metav’s supply network and quality filter support consistent availability and straightforward replenishment when used across larger teams or multi‑site operations. For specification advice, procurement or to confirm availability of the Metav IndustryLine M318.203.3 end gauge for micrometer testing, contact Metav Werkzeuge in Emmerich by phone or e‑mail to secure a traceable calibration standard for the workshop Technical Data Article number: M318.203.3 GTIN: 4054469178417 Category: End gauges Facts Nominal size: 10.3 mm Weight: 0.3 kg Tariff number: 90173000 Special features Material: Special steel Standard: DIN EN ISO 3650/1 Manufacturer: Metav IndustryLine FAQ What is the primary use of this gauge? The end gauge M318.203.3 is intended as a reference standard for checking micrometer accuracy and repeatability during routine inspection and workshop verification. Which standards does the gauge comply with? The component is manufactured to DIN EN ISO 3650/1, confirming its suitability as a dimensional test standard for micrometer checks. What material is used and how does that affect durability? Made from special steel, the gauge offers good wear resistance and dimensional stability under normal workshop handling conditions. How is traceability ensured for this item? Traceability is supported by the article number M318.203.3 and GTIN 4054469178417, which enable clear identification within procurement and inspection records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.5 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of ceramic stability, Grade 1 accuracy and compact handling for consistent inspection results; order the gauge directly via Metav Werkzeuge or consult our specialists for integration into existing measurement routines. Ceramic end gauge 10.5 mm — Grade 1 (DIN 861/1) by Metav IndustryLine The Ceramic end gauge 10.5 mm is a compact, high-stability reference standard designed for precise dimensional checks in workshops and metrology laboratories. Grade 1 tolerance to DIN 861/1 Stable ceramic construction for minimal drift Nominal size 10.5 mm for reference measurements Lightweight 0.017 kg for easy handling Dependable reference for precision checks The Ceramic end gauge 10.5 mm serves as a repeatable reference for routine dimensional verification and instrument checks. Manufactured to Grade 1 according to DIN 861/1, the gauge provides a well-defined nominal size of 10.5 mm, giving clear traceability for inspection processes. As a compact reference standard, it is suitable for bench-top verifications, setting master parts, and cross-checking comparator systems. The documented tolerance class ensures compatibility with workshop and laboratory quality procedures and supports consistent measurement decisions. Why ceramic matters in gauge technology Ceramic as the base material offers significant practical advantages: low thermal expansion reduces size variation with temperature changes, while inherent wear resistance preserves the reference surface over prolonged use. The non-magnetic and chemically inert nature of ceramic further reduces the risk of surface contamination or magnetic interference during checks. With a mass of 0.017 kg, the component is easy to handle while remaining dimensionally stable—attributes that directly translate into reliable results across repeated measurements and extended service intervals. Practical use and handling considerations In routine inspection workflows, the end gauge functions as a quick verification standard for micrometres, callipers, and gauge blocks, and as a reference when setting up measuring instruments. The flat reference faces enable simple seating and alignment on inspection tables or in fixture checks. To maintain accuracy, store the gauge in a clean, dry environment and avoid mechanical shocks; periodic visual inspection for surface wear is recommended. When incorporated into quality routines, the gauge supports traceable documentation of measurement capability and helps maintain consistency between shifts or operators. For a reliable reference standard from Metav IndustryLine, order via Metav Werkzeuge or contact our consultants at info@metav-werkzeuge.com or +49 2822 7131930 to discuss application details and delivery options Technical data SKU: M324.010.5 GTIN: 4054469143095 Weight: 0.017 kg Material: Ceramic Nominal size: 10.5 mm Tolerance grade: 1 (DIN 861/1) Tariff number: 90173000 Facts Nominal size: 10.5 mm Weight: 0.017 kg Special features Material: Ceramic Tolerance class: Grade 1 (DIN 861/1) Compact reference gauge Non-magnetic and wear-resistant FAQ What accuracy does Grade 1 (DIN 861/1) imply for this gauge? Grade 1 indicates a high level of dimensional accuracy in accordance with DIN 861/1; the Ceramic end gauge 10.5 mm is produced to meet those tolerance requirements for reliable reference use. Is the gauge suitable for laboratory and workshop environments? Yes, the ceramic construction and Grade 1 tolerance make the gauge suitable for both workshop inspection benches and laboratory verification tasks. How should the ceramic gauge be stored to preserve accuracy? Store the Ceramic end gauge 10.5 mm in a clean, dry place, protected from mechanical shocks and contamination to maintain the integrity of the reference surfaces. Can the gauge be used with magnetic fixtures or in magnetised environments? The ceramic material of this end gauge is non-magnetic, making it appropriate for use near magnetised fixtures without affecting the gauge material. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.5mm Gauge Block Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of a compact, traceable measurement standard that combines DIN EN ISO 3650 grade 0 accuracy with hardened special steel durability and a stable 35 × 9 mm cross-section for repeatable reference measurements; order the Single gauge block 10.5 mm directly via Metav Werkzeuge or consult our specialists for application advice. Single gauge block 10.5 mm — precision end standard, DIN EN ISO 3650, Grade 0 (Metav IndustryLine) The Single gauge block 10.5 mm is a hardened, precision reference for comparative length measurement and calibration tasks in both workshop and laboratory environments. DIN EN ISO 3650 grade 0 accuracy Hardened special steel construction Stable 35 × 9 mm cross-section Compact nominal size 10.5 mm Reliable reference for traceable quality control The Single gauge block 10.5 mm is produced to DIN EN ISO 3650, grade 0, delivering a high level of dimensional certainty that supports routine quality checks and instrument calibration. Manufactured from hardened special steel, the block resists wear and maintains contact geometry during frequent use, which means fewer remeasurements and more consistent production output. As a compact reference, it provides a simple means to verify micrometres, callipers and other length-measuring devices against a recognised standard, helping to reduce measurement uncertainty in everyday metrology tasks. Geometry designed for repeatability and handling With a cross-section of 35 × 9 mm, the end standard balances stiffness and ergonomic handling for precise contact with gauges and comparators. The relatively robust profile minimises bending and thermal influence during short measurement cycles, increasing reproducibility across multiple measurements. The low mass (approx. 0.011 kg) and compact form factor make it straightforward to position on surface plates or in fixture assemblies without obstructing the setup, while the hardened surface preserves flatness and reduces the need for frequent refurbishment. Practical benefits for workshop and laboratory workflows As a single, nominal 10.5 mm reference, this end measure simplifies inventory of standards: a clearly defined size and DIN EN ISO 3650 conformity allow technicians to integrate it into calibration routines and process documentation with minimal effort. The robust material choice supports sustained daily use in machine shops and inspection benches, delivering a dependable reference for comparative measurements. Traceability and consistent geometry contribute directly to lower rework rates and improved confidence in measurement-based decisions. For a dependable length standard from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to discuss delivery options and integration into existing calibration procedures Technical data SKU: M319.105.0 GTIN: 4054469131580 Category: End gauge / Gauge block Norm: DIN EN ISO 3650 Facts Nominal size: 10.5 mm Weight: 0.011 kg Cross-section: 35 × 9 mm Tariff code: 90173000 Special features Material: Special steel, hardened Grade: 0 (DIN EN ISO 3650) Manufacturer: Metav IndustryLine Single-piece end standard FAQ What tolerance class does this gauge block follow? The Single gauge block 10.5 mm is manufactured to DIN EN ISO 3650 grade 0, providing the tolerance specification associated with grade 0 for comparative measurement. Can the Single gauge block 10.5 mm be used as a workshop reference? Yes, the Single gauge block 10.5 mm, made from hardened special steel, is suitable as a durable workshop reference for checking micrometres and callipers. Why is the 35 × 9 mm cross-section important? A 35 × 9 mm cross-section offers the stiffness required to reduce bending and thermal effects during short measurements, helping the Single gauge block 10.5 mm produce repeatable results. Which instruments are commonly verified with this end standard? The Single gauge block 10.5 mm is typically used for comparative checks of micrometres, dial gauges, vernier instruments and calibration setups on surface plates. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.5mm Gauge Block, Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of DIN EN ISO 3650 Grade 1 accuracy combined with a hardened special steel construction and compact dimensions for reliable, repeatable gauging in production or inspection. Order the gauge directly via Metav Werkzeuge or consult our specialists for delivery and traceability details. End gauge 10.5 mm — DIN EN ISO 3650, Grade 1 (Metav IndustryLine) The End gauge 10.5 mm is a compact, high-precision reference standard for dimensional checks in inspection rooms and toolrooms, engineered for repeatability and low wear. DIN EN ISO 3650 Grade 1 accuracy Hardened special steel construction Compact geometry for consistent measurements Traceable SKU and GTIN for inventory control Precision that fits into every inspection routine The gauge conforms to DIN EN ISO 3650, classified as Grade 1, which ensures a high level of dimensional fidelity for master references. With a nominal size of 10.5 mm, this end measure provides a stable reference point for incoming inspection and production checks. The standardised tolerance band associated with Grade 1 supports consistent pass/fail decisions and reduces rework by enabling clear, technical acceptance criteria. The compact nature of the device simplifies handling in busy metrology benches while maintaining the stability required for repeatable readings. Durable design for frequent use and long service life Manufactured from hardened special steel, the gauge resists abrasion and retains its geometry under repeated contact. The cross-section specified for sizes above 10.1 mm is 35 × 9 mm, providing a robust profile that minimises bending and wear during routine use. This combination of material and form factor limits long-term drift and helps to preserve the gauge as a reliable master. The low mass and compact dimensions also make storage and handling straightforward, while the hardened finish reduces the need for frequent refurbishment. Practical integration into inspection workflows As a fixed-length end standard, this device is suitable as a reference in Go/No‑Go checks, comparative verifications and calibration benches where a certified master is required. The product is supplied with a unique SKU: M319.105.1 and GTIN: 4054469131597, facilitating traceable stock management and documentation in quality systems. For specialist applications, the robust geometry and conformity to recognised standards allow easy incorporation into inspection plans, drawing comparisons against gauges and micrometres to secure consistent measurement chains. For assured Grade 1 performance and proven durability, contact Metav Werkzeuge to arrange purchase, delivery options and documentation matching your traceability requirements Technical data SKU: M319.105.1 GTIN: 4054469131597 Label: End gauge 10.5 mm, DIN EN ISO 3650, Grade 1 Facts Nominal size: 10.5 mm Weight: 0.011 kg Tariff code: 90173000 Special features Material: Hardened special steel Standard: DIN EN ISO 3650, Grade 1 Cross-section: from 10.1 mm → 35×9 mm FAQ What accuracy class does the gauge meet? The gauge complies with DIN EN ISO 3650 Grade 1; the End gauge 10.5 mm (SKU M319.105.1) is intended as a high‑precision reference for dimensional verification. What material is the gauge made from? The device is manufactured from hardened special steel, chosen for wear resistance and long-term stability. How is the gauge typically used in inspection processes? The end measure serves as a fixed-length reference for comparative checks, master verification and routine Go/No‑Go assessments in production and incoming inspection. Is traceability provided for stock and documentation? Yes. The product features a GTIN (4054469131597) and the SKU shown above to support traceable inventory and quality records. Does the gauge include a calibration certificate? Unless explicitly stated in the article listing, the gauge is supplied as described; any calibration documentation (if provided) will be noted separately in the product details. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of Grade 1 accuracy, a 100 mm reference length and the intrinsic stability of ceramic construction to secure reliable, repeatable length checks in laboratory and production environments. Order the gauge block via Metav Werkzeuge or consult the team for integration advice. Ceramic gauge block 100 mm, Grade 1 DIN 861/1 — precision reference from Metav IndustryLine The Ceramic gauge block 100 mm, Grade 1 DIN 861/1 serves as a stable length standard for comparative measurements and routine verification in metrology laboratories and production quality control. Grade 1 accuracy to DIN 861/1 Dimensionally stable ceramic material Precision reference length 100 mm Suitable for laboratory and production control Ensure reproducible length checks with a Grade 1 reference A Grade 1 gauge block built to DIN 861/1 provides a defined tolerance class that supports consistent dimensional inspection and calibration of workshop instruments. As a 100 mm reference, this block bridges bench‑scale checks and higher‑precision comparators, reducing measurement uncertainty where it matters most. The specified grade and standardisation give a reliable baseline for pass/fail criteria, contributing to fewer rejects and more predictable production outcomes. Ceramic construction for thermal and chemical resilience The ceramic material offers thermal stability and resistance to surface degradation, which preserves the gauge block's reference length over time and under typical workshop conditions. Compared with softer metals, the ceramic surface shows enhanced wear characteristics and reduced susceptibility to corrosion, which means the reference remains credible across repeated use. These material properties translate into longer service intervals and a reduced need for frequent recalibration when used within appropriate handling and storage routines. Practical fit for calibration benches and quality workflows At 100 mm, this reference length is widely compatible with comparator stands, gauge sets and micrometre verifications, making it straightforward to integrate into existing measurement routines. The compact format eases handling while providing a stable measuring basis for comparative measurement chains. When combined with formal traceability practices and documented procedures, the block supports reproducible inspection results and helps maintain process control across shifts or locations. For assured reference accuracy and to discuss suitability for specific measurement chains, contact Metav Werkzeuge about integrating the Metav IndustryLine ceramic gauge block into calibration and quality-control workflows via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: M324.100 GTIN: 4054469143477 Material: Ceramic Nominal length: 100 mm Weight: 0.19 kg Grade: 1 (DIN 861/1) Tariff number: 90173000 Facts Nominal length: 100 mm Weight: 0.19 kg GTIN: 4054469143477 Tariff number: 90173000 Grade: 1 (DIN 861/1) Special features Ceramic construction Compliant with DIN 861/1 Category: Gauge block / end measure Intended use: Reference standard for length measurement in laboratory and production settings FAQ What does Grade 1 according to DIN 861/1 mean for accuracy? Grade 1 denotes a standardised tolerance class under DIN 861/1; the Ceramic gauge block 100 mm, Grade 1 DIN 861/1 is manufactured to meet those limits and is intended for industrial precision checks rather than sub‑micrometre reference duties. Why choose a ceramic gauge block instead of a steel one? The ceramic construction of the Ceramic gauge block 100 mm, Grade 1 DIN 861/1 offers improved dimensional stability against temperature shifts and enhanced surface durability, which benefits repeated comparative measurements in mixed workshop environments. Is this gauge block suitable for use on a comparator bench? Yes, the 100 mm reference length is well suited to comparator stands and common bench equipment; the block functions as a stable master for verifying the performance of measuring instruments. How should the gauge block be stored to maintain accuracy? Store the block clean and dry at a stable ambient temperature, protected from mechanical shocks and contamination; use a dedicated protective case and suitable handling practices to preserve the reference surface. Which instruments can be checked using this gauge block? Typical applications include verification of calipers, micrometres, comparator systems and other length‑measuring instruments where a traceable 100 mm reference is required; the block is a versatile element in routine quality checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100 mm End Gauge Holder Very Robust Design - Metav IndustryLine
Take advantage of the holder's robust construction, defined 0–100 mm clamping range and compact mass to ensure repeatable reference measurements in calibration and inspection workflows; order the unit directly via Metav Werkzeuge or consult our technical team for integration advice. Gauge block holder 100 mm – Gauge block holder with 0–100 mm clamping range (Metav IndustryLine) The gauge block holder 100 mm secures gauge blocks for precise comparison and calibration work, providing a stable clamping solution for metrology benches and workshop inspection stations. Robust, heavy-duty construction Clamping range 0–100 mm for small gauges Cross-section 30.5 x 2.5 mm profile Compact mass 0.4 kg for easy handling Repeatable support for precision measurement A dedicated holder stabilises reference standards during comparison routines; by fixing gauge blocks in a defined position the risk of positional drift and operator-induced variance is reduced. The 0–100 mm clamping span covers the most common small reference sets, while the squared 30.5 x 2.5 mm profile ensures mechanical rigidity under clamping force. For workshops and calibration labs this translates into more repeatable results and fewer re-checks, improving throughput in quality control processes while maintaining traceability to standard gauges. Robust build for long-term, reliable use Built as a very stable execution, this holder is designed for continuous use under workshop conditions. The compact mass of 0.4 kg makes the device simple to reposition without compromising stability during an inspection sequence. The substantial profile minimises bending and ensures that clamped gauge blocks remain aligned over repeated cycles. As a result, maintenance intervals are reduced and the holder becomes a dependable element in routine measurement chains and device verification procedures. Faster setups and clearer measurement routines Faster, predictable clamping reduces per-measurement setup time and simplifies operator training. The holder is intended for use with gauge blocks when establishing reference lengths, facilitating external comparison of callipers, micrometres or other length measuring instruments. By providing a consistent clamping geometry, the device supports efficient inspection work and helps to avoid time-consuming adjustments, making it particularly suitable for production testing and incoming goods inspection where quick verification is essential. For a tailored recommendation on integrating the gauge block holder into existing measurement setups, contact Metav Werkzeuge to discuss technical compatibility and delivery options for the M317.104 unit. Technical Data Article number: M317.104 GTIN: 4054469127347 EClass: 21170108 Description: Gauge block holder Facts Clamping range: 0–100 mm Cross-section: 30.5 x 2.5 mm Mass: 0.4 kg Customs tariff number: 90173000 Special features Very stable execution Intended for use with gauge blocks Category: Endmasse Suitable for calibration and comparison tasks FAQ What is the clamping range of the holder? The clamping range is 0–100 mm, enabling secure fixing of standard small gauge block sets for measurement and comparison. Is the holder suitable for workshop and laboratory use? Yes, the holder’s robust construction and compact mass make it suitable for both metrology laboratories and workshop inspection benches. Which profile dimensions ensure rigidity? The profile measures 30.5 x 2.5 mm, which contributes to mechanical rigidity and reproducible clamping conditions. Can the holder be used to support calliper calibration? The holder is intended for gauge-block-based comparison; it provides a stable reference for calibrating callipers, micrometres and other length measuring instruments. What is the product reference for ordering and documentation? Refer to the SKU M317.104 (GTIN 4054469127347) when ordering or requesting technical information. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100 mm Gauge Block Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of a certified reference with DIN EN ISO 3650 Grade 1 conformity and a 100 mm nominal size to secure repeatable dimensional checks; the hardened special steel construction and compact cross-section combine stability with easy handling for routine inspection tasks. Order directly via Metav Werkzeuge for reliable supply or contact the technical team for application advice. End gauge 100 mm (DIN EN ISO 3650), Grade 1 — Metav IndustryLine The End gauge 100 mm (DIN EN ISO 3650) Grade 1 serves as a precision reference for dimensional inspection and quality control in production and laboratory environments. DIN EN ISO 3650 Grade 1 precision 100 mm nominal length as reference standard Hardened special steel construction Compact cross-section for stable handling Accuracy that supports quality assurance and reduces rework The DIN EN ISO 3650 specification and Grade 1 designation indicate a high level of dimensional fidelity suitable for routine calibration and verification tasks. As a 100 mm reference, this gauge provides a stable baseline for checking calipers, micrometres and other measuring devices, helping to reduce measurement variance and avoid costly rework. The standardised tolerance class ensures compatibility with established inspection procedures and supports traceable decisions during incoming and final inspections. Robust materials and form for reproducible results Manufactured from hardened special steel, the gauge resists wear and maintains dimension under frequent use, which increases the interval between replacements and preserves measurement integrity. The specified cross-section dimensions (30 x 9 mm up to 10 mm; 35 x 9 mm above 10.1 mm) give the gauge a balanced stiffness-to-mass ratio, minimising bending and thermal drift during handling. At approximately 0.243 kg, the component remains easy to manipulate on the bench while providing the rigidity needed for repeatable contact measurements. Practical integration into inspection workflows Designed as a compact reference standard, the gauge fits inspection benches and calibration setups without special fixtures. It is suitable for direct comparison measurements and routine verification of hand tools and precision instruments, contributing to faster quality decisions on the shop floor. Clear standard compliance simplifies documentation for quality audits and helps maintain consistent measurement chains across suppliers and production sites. Choose the Metav IndustryLine reference gauge for dependable standardisation in every inspection process and contact Metav Werkzeuge in Emmerich for tailored technical guidance and fast delivery: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: M320.100.1 GTIN: 4054469132358 Norm: DIN EN ISO 3650 Grade: 1 Facts Nominal size: 100 mm Weight: 0.243 kg Tariff number: 90173000 Cross-section: up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm Special features Material: special steel, hardened Category: End gauges Suitable for precision dimensional checks FAQ What tolerance class does Grade 1 represent under DIN EN ISO 3650? Grade 1 denotes a high-precision tolerance band according to DIN EN ISO 3650; the End gauge 100 mm (DIN EN ISO 3650) Grade 1 is intended for reliable reference use in inspection and verification. Can this gauge be used to verify calipers and micrometres? Yes. The gauge’s 100 mm nominal length and Grade 1 conformity make it suitable as a reference for checking calipers, micrometres and similar measuring instruments. What material is the gauge made from and why does it matter? The gauge is made from hardened special steel, which improves wear resistance and dimensional stability during repeated contact measurements. Is the cross-section relevant for measurement stability? Indeed; the specified cross-section dimensions provide the stiffness required to reduce bending and thermal effects, ensuring reproducible results during handling. Which SKU should be referenced when ordering or documenting this gauge? Use SKU M320.100.1 to reference the End gauge 100 mm (DIN EN ISO 3650) Grade 1 in orders and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100 mm Gauge Block, Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of Grade 0 accuracy, hardened special steel construction and strict DIN EN ISO 3650 conformity for reliable reference measurements and repeatable set-ups — order directly via Metav Werkzeuge or consult our specialists for selection advice. Single gauge block 100 mm — Grade 0, DIN EN ISO 3650 (Metav IndustryLine) The Single gauge block 100 mm is a precision reference length for calibration, inspection and machine set-up tasks in production and metrology environments. Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel construction Nominal length 100 mm Precision reference for calibration labs Confidence from standardised accuracy Manufactured to DIN EN ISO 3650 and classified as Grade 0, this reference element provides a documented tolerance class for high‑precision comparison and length setting. The tight tolerance of the Grade 0 specification reduces setup time and measurement uncertainty when establishing reference chains or verifying instruments. As a traceable length standard, the block supports reproducible measurement procedures and helps to maintain process stability across inspection routines. Robust design for repeatable handling The block is produced from special steel, hardened to ensure long service life and consistent surface integrity under regular use. The compact geometry and defined cross-section sizes maintain stiffness and simplify positioning between holders or on reference plates. At approximately 0.243 kg, the piece is easy to manipulate while remaining substantial enough for stable contact during comparisons. These characteristics lower the risk of handling‑induced deviation and make the element suitable for both workshop and laboratory environments. Practical role in measurement and production workflows Used as a reference for calibrating micrometers, setting gauge lengths and checking machine offsets, this precision length standard reduces downtime associated with frequent verification. The block supports efficient quality assurance workflows by providing a reliable master length that integrates into master sets and inspection benches. Metav IndustryLine’s supply reliability and broad product range further simplify reordering and set completion for busy workshops and calibration laboratories. Contact Metav Werkzeuge in Emmerich for tailored advice on integrating this Grade 0 100 mm reference into inspection routines or for assistance with kit selection and rapid supply Technical data SKU: M320.100.0 GTIN: 4054469132341 Norm: DIN EN ISO 3650 Facts Nominal length: 100 mm Tolerance grade: 0 Weight: 0.243 kg Tariff number: 90173000 Special features Material: Special steel, hardened Cross-section (≤10 mm): 30 x 9 mm Cross-section (>10.1 mm): 35 x 9 mm Category: Gauge blocks / End measures FAQ What tolerance class does this gauge block meet? The Single gauge block 100 mm meets Grade 0 tolerances according to DIN EN ISO 3650, providing the dimensional stability required for high‑precision comparisons. Which material is used and how does it affect wear? This Metav IndustryLine gauge block is produced from special steel, hardened, which gives good wear resistance and maintains surface integrity during repeated use. Is the block suitable for workshop and laboratory use? Yes — the 100 mm nominal length and robust construction make this gauge block appropriate for calibration benches, comparator setups and workshop verification tasks. How should the block be stored to preserve accuracy? Store the block clean and dry, ideally in a protective case or drawer to avoid corrosion and surface damage; the hardened steel construction helps, but careful storage preserves long‑term accuracy. What is the SKU for ordering and traceability? The product is listed under SKU M320.100.0 (Metav IndustryLine) and GTIN 4054469132341 for ordering and inventory control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100 x 25 mm Plain Glass Surface Plate 0.1 µm Flatness Accuracy - Metav IndustryLine
Take advantage of the combination of 0.1 µm flatness, a compact 100 mm diameter and a robust 25 mm section for reliable surface verification; order the reference directly via Metav Werkzeuge or consult the specialists for application advice. Optical flat 100 x 25 mm, 0.1 µm flatness (Metav IndustryLine) The optical flat 100 x 25 mm is a precision reference tool for fast visual and comparative flatness checks in inspection benches and workshop metrology. Flatness 0.1 µm for high-precision checks 100 mm diameter with 25 mm thickness Low mass 0.3 kg for easy handling Suited for parallel supports and reference measurements Trusted reference for precise flatness verification The plate provides a guaranteed flatness of 0.1 µm across a 100 mm contact area, making it suitable as a reference for comparative surface assessments and quick inspection routines. Such a level of accuracy detects submicrometre deviations that commonly escape coarse gauges; this brings measurable improvements to quality control processes and reduces the risk of downstream rework. The model is identified as M318.224, which fits a workshop environment where reproducible, repeatable checks are required. Compact, stiff design for practical workshop use With a thickness of 25 mm the component offers a stable reference surface that resists bending during manual placement. The overall mass of 0.3 kg keeps handling straightforward while limiting contact-induced distortion, supporting reliable results even in routine use. The compact footprint simplifies storage on inspection benches and compatibility with established parallel supports, so integration into existing measurement setups is immediate and efficient. Simple application and workflow benefits Used as a comparative standard, the optical flat enables quick visual inspection via interference fringes or as a datum for tactile and optical comparative measurements. The product supports common metrology tasks such as checking planarity of machined faces, verifying parallel plates and confirming assembly seating surfaces. As a readily available precision reference, the plate improves throughput in inspection workflows and helps maintain production tolerances without complex setup. For dependable workshop-grade flatness checks, choose the Metav IndustryLine optical flat M318.224 and contact Metav Werkzeuge for direct supply and practical advice from Emmerich. Technical Data Article number: M318.224 GTIN: 4054469184258 Label: Planglas, 100 x 25 mm Genauigkeit 0,1 um Weight: 0.3 kg Facts Diameter: 100 mm Thickness: 25 mm Flatness tolerance: 0.1 µm Mass: 0.3 kg Special features Product type: optical flat / flat glass Category: Parallel supports (Parallelunterlagen) Intended use: checking surface flatness and reference measurements ECLASS: 21170126 FAQ What level of flatness does this reference achieve? The optical flat M318.224 from Metav IndustryLine provides a flatness tolerance of 0.1 µm, suitable for fine inspection and comparative checks. How is the plate typically used in a workshop? The plate is placed on the test surface and used as a reference for visual interference checks or comparative measurement procedures; the Metav IndustryLine optical flat is intended for quick verification of planarity and seating surfaces. Is the component easy to handle during routine inspections? Yes; with a 100 mm diameter and a mass of 0.3 kg, the flat is compact and light enough for single-person handling while remaining sufficiently stiff for reproducible checks. Which measurement tasks is this product suited for? The device is designed for flatness verification of machined faces, checking parallel supports and serving as a workshop reference for routine quality control tasks. Does the product fit into existing inspection setups? The item integrates well with standard inspection benches and parallel supports; the compact dimensions and robust section make it practical for immediate use in established workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100 x 70 x 25 mm Foot for Gauge Block Holder Very Sturdy Design - Metav IndustryLine
Take advantage of a very robust construction, compact footprint and precise geometry to secure repeatable measurements during gauge calibration and inspection. The solid base and defined cross-section give stable support for end gauge holders, reducing setup variability. Order the component directly via Metav Werkzeuge or contact our consultants for specification matching. Foot for End Gauge Holder M317.111 — Robust 100 x 70 x 25 mm base (Metav IndustryLine) Foot for End Gauge Holder M317.111 is a compact metrology base designed to stabilise end gauge holders during calibration and inspection. Very robust construction Compact 100 x 70 x 25 mm footprint Defined 30.5 x 2.5 mm cross-section Stable support that reduces measurement scatter The robust construction of this base ensures a secure seating for end gauge holders, which directly reduces setup variability and improves repeatability in calibration routines. With a deliberately compact footprint of 100 x 70 x 25 mm, the component is easy to position on workbenches or inside inspection jigs while still providing the mass needed to dampen minor vibrations. This stability contributes to more reliable results during routine gauge verification. Precise geometry for consistent alignment A consistently machined contact area and the 30.5 x 2.5 mm cross-section provide a predictable interface between the base and the holder, helping to maintain alignment across repetitive measurements. The geometric definition is intended to limit micro-movements that otherwise introduce error, so the base functions as a simple but effective measure to uphold dimensional traceability during gauge use. Designed for workshop and calibration environments The construction and modest weight of 1.2 kg make the base suitable for both bench-mounted and portable calibration setups where a stable datum is required. Its dimensions allow compatibility with a range of holders without occupying excessive workspace, offering a practical balance between rigidity and manoeuvrability for quality control departments and metrology benches. Durability that supports long-term workflows A very stable design translates into fewer adjustments and less wear on mating parts over time, supporting continuous operation in production or laboratory environments. The component’s durability helps to reduce downtime associated with repositioning or re-clamping, which in turn supports efficient throughput in calibration cycles and routine inspection tasks. Practical handling and integration The compact form factor simplifies storage and handling; the base can be integrated into existing fixtures or used as a stand-alone datum. Its clearly defined geometry assists technicians in achieving reproducible setups quickly, which is particularly useful when several instruments are verified in succession or when time-sensitive quality checks are performed. Contact Metav Werkzeuge for application advice or to request detailed specifications for the Metav IndustryLine base M317.111 — our consultants in Emmerich will ensure the component meets the required calibration and inspection needs. Technical data SKU: M317.111 GTIN: 4054469127415 eClass: 21170108 Category: End gauge components Country tariff number: 90173000 Facts Dimensions: 100 x 70 x 25 mm Cross-section: 30.5 x 2.5 mm Weight: 1.2 kg Special features Very stable construction Intended as a base for end gauge holders Compact footprint suitable for bench and jig use Manufacturer: Metav IndustryLine Story trigger: end gauges FAQ What are the exact dimensions of the base? The base measures 100 x 70 x 25 mm; the cross-section is 30.5 x 2.5 mm and the weight is approximately 1.2 kg for the Metav IndustryLine foot M317.111. Is the base suitable for calibration benches and mobile inspection setups? Yes, the design of the Metav IndustryLine foot for end gauge holders (M317.111) is compact yet stable, making it suitable for both calibration benches and portable inspection arrangements. How does the base improve measurement repeatability? The defined geometry and robust construction of M317.111 reduce micro-movements and vibration at the interface with the holder, which improves alignment stability and repeatability during gauge verification. Can this base be integrated into existing fixtures? Integration is straightforward: the compact dimensions and flat mounting footprint allow the base to be incorporated into existing fixtures or used as a stand-alone datum in inspection jigs. Who supplies this component and where can specification enquiries be directed? The component is supplied under Metav IndustryLine. For further specification details, contact Metav Werkzeuge for assistance with application matching and technical data. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100-200 mm End Gauge Holder Stable Design, 30.5x2.5 mm Cross Section - Metav IndustryLine
The combination of a very stable construction, a 100–200 mm clamping range and a compact 30.5 x 2.5 mm cross-section ensures repeatable alignment of gauge blocks for reliable calibration jobs; order the holder directly via Metav Werkzeuge or ask our consultants if needed End gauge holder 200 mm — clamping range 100–200 mm (Metav IndustryLine) The End gauge holder 200 mm clamping range 100–200 mm secures gauge blocks for precise measurement and calibration tasks in workshop and laboratory environments Very stable construction Clamping range 100–200 mm Cross-section 30.5 x 2.5 mm For precision gauge blocks and calibration Stability that secures repeatable measurements A robust fixture is the first prerequisite for reproducible dimensional control. The holder features a very stable construction that reduces deflection and vibration during setup, which in turn lowers measurement scatter in serial checks. With a clamping range of 100–200 mm, the device covers common block stacks used in workshop calibration and quality control, enabling consistent positioning of precision standards. The specified cross-section (30.5 x 2.5 mm) contributes to lateral rigidity while keeping the unit easy to handle; the modest weight of 0.6 kg supports rapid exchange without compromising stability. Designed for efficient calibration flow By holding gauge blocks securely, the device streamlines calibration and comparative measurements: stacks remain aligned, contact surfaces are stable, and transfer errors are minimised. This holder is intended as a practical aid for routine calibration of measuring instruments and for comparative length checks in production or inspection. The design focuses on operational efficiency — quick clamping, unambiguous seating and repeatable positioning translate into shorter cycle times and fewer re-measurements, which supports higher throughput in the metrology bench or workshop. Built for workshop and lab continuity Durability and predictable behaviour across repeated cycles are decisive for everyday use. The holder’s construction resists typical workshop influences and maintains alignment during handling and repositioning. Compatibility with standard gauge blocks makes integration straightforward and avoids the need for special adapters; the unit is therefore suitable for quality-control stations, calibration labs and assembly areas. Backed by Metav’s emphasis on accessible precision, this solution forms part of a broader offering that combines practical reliability with supply-chain transparency from Emmerich. Contact Metav Werkzeuge to secure the Metav IndustryLine gauge block holder M317.105 for reliable calibration and to discuss application specifics with our technical consultants Technical data Article number: M317.105 GTIN: 4054469127354 ECLASS: 21170108 Category: Gauge blocks Facts Holder length: 200 mm Clamping range: 100–200 mm Cross-section: 30.5 x 2.5 mm Weight: 0.6 kg Special features Very stable construction Suitable for precision gauge blocks and calibration Customs tariff number: 90173000 FAQ What is the primary use of this gauge block holder? The gauge block holder is designed to secure gauge blocks for precise measurement and calibration tasks, providing stable support for comparative checks and instrument adjustment. Which clamping range does the holder cover? The holder supports a clamping range of 100–200 mm, which covers typical gauge block stacks used in workshop and calibration-laboratory routines. Is the holder compatible with standard gauge blocks? Yes, the design is compatible with standard gauge blocks and intended for use in calibration and quality-control workflows. How does the construction affect measurement repeatability? The very stable construction reduces deflection and handling-induced variation, improving repeatability when conducting serial measurements or instrument adjustments. What is the product identifier for ordering? The gauge block holder is listed as M317.105 in the Metav IndustryLine range and can be referenced when specifying or ordering the item. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
ensure traceable length calibration with gauge blocks
gauge blocks, also called slip gauges or end gauges, are precision length standards designed to transfer exact measures during calibration and setup. Manufactured and graded for metrological use, they provide the reference dimensions needed to verify and adjust measuring instruments in industrial workshops and calibration labs.
how gauge blocks work and where they are essential
gauge blocks are used to create known lengths by wringing individual blocks together or by using a single block as a reference. length calibration in industry commonly relies on parallel gauge blocks, while angle, cylinder and sphere end gauges serve specialised tasks. these blocks are produced in steel, ceramic or carbide, and their material choice balances wear resistance with thermal behaviour. regular calibration—typically performed annually—by DAkkS-accredited laboratories ensures traceability. the highest-precision reference work, class K, is certified by the PTB using laser techniques; classes 0, 1 and 2 are tested under progressively less controlled conditions (class 0 in a climate-controlled lab, class 1 in a standard measurement room, class 2 in production).
measurable benefits that cut downtime and uncertainty
- consistent, traceable length standards reduce rework and measurement disputes by enabling reliable instrument calibration.
- choosing the correct material (steel, ceramic, carbide) extends service life and limits wear in high-use environments.
- selecting the right accuracy class (K, 0, 1 or 2) matches calibration effort to application needs and avoids over‑specification.
- annual calibration by accredited labs maintains documented compliance and supports quality systems such as ISO.
why Metav is a smart partner for precision standards
Metav combines specialist knowledge with a broad range of measurement technology, making the procurement of gauge blocks straightforward and dependable. with over 48,000 customers and more than 250,000 products stocked from Emmerich, Metav acts as a pragmatic quality filter for European workshops, reducing supplier complexity and ensuring consistent supply.
In short, gauge blocks deliver traceable, material‑appropriate and class‑matched references that keep calibration workflows efficient and auditable.
faq
what materials are gauge blocks available in and why does it matter?
gauge blocks are typically supplied in steel, ceramic or carbide. material choice affects wear resistance, stability and thermal expansion; selecting the right material for your environment optimises longevity and measurement stability.
how often should gauge blocks be calibrated?
industry practice is an annual calibration cycle, carried out by DAkkS-accredited laboratories, though frequency can be increased depending on usage and required uncertainty.
what do the accuracy classes k, 0, 1 and 2 indicate?
the classes denote graded tolerances and test conditions: K is the highest precision (certified by PTB with laser measurement), class 0 is checked under climate-controlled lab conditions, class 1 in a normal measurement room and class 2 in production environments.
are parallel gauge blocks always used for length calibration?
yes; for length calibration the parallel gauge blocks are the primary standard because they provide exact planar faces for wringing and stacking to create precise lengths.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com