End gauges for precise length calibration
End gauges provide exact reference lengths for calibrating measurement instruments and ensuring consistent dimensional accuracy in metalworking and inspection processes. Used in production and laboratory settings, these end gauges—made from steel, ceramic or carbide—allow technicians to compensate for wear and thermal effects and maintain measurement traceability, especially when employed alongside parallel end gauges, cylinder gauges and calibration masters. Classes 0, 1 and 2 define practical tolerance levels for workshop, inspection-room and production use respectively, delivering the repeatable precision required for machining and quality control.
100-200mm Gauge Block Accessory Set With Holders, Scriber And Centre Pin, Transport Case - Metav IndustryLine
Take advantage of a very stable construction and the included holders for 0–50 mm, 0–100 mm and 100–200 mm to achieve repeatable set-ups and reliable calibration results; the compact 12-piece composition reduces changeover time and supports precise marking and centring tasks. Order the accessory set directly via Metav Werkzeuge or consult our advisors for application guidance. End gauge accessory set II — 12-piece set with 0–200 mm holders (Metav IndustryLine) The End gauge accessory set II provides a compact, workshop-ready collection of holders and tips for end gauges, designed for precision measurement support and calibration work in metrology and quality assurance environments. Robust, stable construction for repeatable setups Contains holders 0–50, 0–100 and 100–200 mm Complete 12-piece set with scribing and centring tips Includes foot holder and two measuring jaws Durable design for repeatable measurements The kit is engineered with a robust construction that reduces distortion during use, supporting more consistent results on inspection benches. By fixing end gauges in predefined holders for 0–50 mm, 0–100 mm and 100–200 mm ranges, the set improves positional stability and lowers operator-induced variance. This predictable behaviour translates into fewer rechecks and a smoother measurement workflow, which is particularly valuable in routine calibration and incoming inspection processes. Content tailored to calibration and workshop tasks Supplied as a 12-piece arrangement, the set bundles holders, two measuring jaws, a scribing tip, a centring point and a foot holder, so that common preparation and marking steps are covered without additional improvised tooling. The inclusion of dedicated tips simplifies transfer scribing and centring operations; the practical composition is intended to shorten setup times and to make batch checks and gauge adjustments more efficient. The clear component logic supports traceable calibration procedures and repeatable reference set-ups. Practical use cases and compatibility with inspection routines Ideal for metrology labs, toolrooms and maintenance workshops, the accessory set supports consistent alignment of end gauges and simplifies the creation of test rigs for component inspection. The combination of precision holders and purpose-made tips makes the kit suitable for series checks, calibration support and fixture set-up. For technicians aiming to increase throughput while maintaining measurement confidence, the set offers a compact solution that integrates into existing measurement benches and gauge stations. For precise end-gauge work choose the Metav IndustryLine accessory set II and contact Metav Werkzeuge for tailored ordering or technical advice from our Emmerich-based specialists. Technical data SKU: M317.102 GTIN: 4054469127323 EClass: 21170108 Tariff number: 90173000 Pieces per set: 12 Facts Holder ranges: 0–50 mm; 0–100 mm; 100–200 mm Measuring jaws: 2 Weight: 2 kg Item type: End gauge accessory set Special features Very stable construction Includes scribing tip and centring point Foot holder included Designed for use with end gauges and calibration tasks FAQ What components are included in the set? The End gauge accessory set II (SKU M317.102) contains holders for 0–50 mm, 0–100 mm and 100–200 mm, two measuring jaws, a scribing tip, a centring point, a foot holder and associated mounting parts in a 12-piece composition. Which measurement ranges does the kit cover? The delivered holders provide direct support for gauges in the 0–50 mm, 0–100 mm and 100–200 mm ranges, enabling work across the most common end-gauge intervals used in workshop and inspection routines. Is the set suitable for calibration tasks? Yes. The End gauge accessory set II is intended to assist calibration and routine checks by providing stable positioning and dedicated tips for marking and centring, which support traceable inspection procedures. Can this kit be used on production inspection benches? The kit has been designed for practical use in metrology labs and production inspection benches where repeatable set-ups and efficient changeovers are required, helping to reduce inspection time on recurring tasks. What ensures the stability of the accessories during measurement? Stability is achieved through the set’s very stable construction and purpose-made holders, which minimise movement and help preserve alignment during measurement and marking operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100-250mm End Gauge Holder Very Sturdy Construction - Metav IndustryLine
Take advantage of the combination of a very stable construction, a practical 100–250 mm clamping range and lightweight handling to secure repeatable measurements and streamline calibration routines. Order the end-gauge holder directly via Metav Werkzeuge or ask our consultants if needed. End-gauge holder 100–250 mm — robust clamping for calibration, Metav IndustryLine The End-gauge holder 100–250 mm secures end measures for precise measurement and calibration tasks in workshops and metrology environments, offering a compact solution for reliable instrument verification and repeatable setups. Very stable construction Clamping range 100–250 mm Lightweight 0.4 kg for easy handling Optimised for precise calibration tasks Repeatable clamping for consistent measurement results A robust mounting design reduces flex and play, ensuring repeatable positioning of end measures across sequential checks. The holder’s very stable construction minimises influence from handling and vibration, so calibration runs deliver consistent results with fewer re-measures. For workshop or inspection routines this stability shortens cycle times and reduces variance in measurement data, which supports faster decision making in quality control processes. Built for calibration workflows and easy handling The clamping range of 100–250 mm covers the typical span required for standard end measures, while the slim cross‑section (30 x 5 mm for sizes up to 300 mm) keeps the assembly compact and accessible. With a weight of 0.4 kg, the unit is simple to reposition on benches or within test rigs without sacrificing stiffness. The design is optimised for the mounting and verification of gauge blocks and end measures, enabling precise alignment and straightforward integration into existing inspection setups. Practical advantages that support production and metrology Using a dedicated holder reduces setup time and helps to protect reference gauges from accidental contact during handling. The device is suitable for routine calibration and verification of measuring instruments and supports traceable, reproducible measuring sequences. Combined with Metav’s logistics and product range, the holder contributes to a dependable measurement workflow and makes high-precision routines accessible in small workshops as well as larger inspection departments. For tailored advice on integrating this Metav IndustryLine holder into calibration procedures, or to request support from Metav Werkzeuge, contact our technical team in Emmerich for prompt guidance and reliable delivery. Technical Data Article number: M317.205.1 GTIN: 4054469159324 Clamping range: 100–250 mm Weight: 0.4 kg Facts Cross-section (up to 300 mm): 30 x 5 mm Classification: 21170108 Tariff number: 90173000 Special features Very stable construction Suitable for use with end measures for precise measurement and calibration Brand: Metav IndustryLine FAQ What is the intended use of this holder? The holder is designed to secure end measures for precise measurement and calibration of measuring devices, enabling repeatable setups during verification. Which clamping range does the unit cover? The clamping range is 100–250 mm, making it suitable for standard end measures within that span. Is the holder suitable for workshop and laboratory environments? Yes, the robust design and compact cross-section make it appropriate for both workshop inspection benches and metrology labs. Does the item include a manufacturer SKU or article number for ordering? Orders can be placed using article number M317.205.1 or GTIN 4054469159324 to ensure the correct Metav IndustryLine model is supplied. How does the holder contribute to measurement quality? By reducing flex and stabilising end measures, the holder improves repeatability and reduces measurement variance during calibration routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Gauge Block End Measure Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of the combination of DIN EN ISO 3650 conformity, Grade 0 accuracy and a rigid, hardened special steel design for reliable master-length control in calibration and inspection routines. Order the gauge block directly via Metav Werkzeuge or consult the Metav team for specification support and logistic options. Gauge block 1000 mm — End gauge, DIN EN ISO 3650, Grade 0 (Metav IndustryLine) The gauge block is a 1,000 mm length standard for high-precision calibration and master checks in dimensional laboratories and quality departments. DIN EN ISO 3650, Grade 0 accuracy Hardened special steel construction 1,000 mm nominal length, stable profile Cross-section 35 x 9 mm, balanced rigidity Consistent master for laboratory and workshop use The long-format gauge block serves as a reproducible length master where traceable reference dimensions are required. Manufactured to DIN EN ISO 3650 and specified as Grade 0, this length standard provides the level of geometric accuracy demanded in final inspection and calibration jigs. The nominal 1,000 mm size reduces the need for compound stacking in many workflows, cutting handling time and cumulative error when setting up comparative measurements. Engineered stiffness and dimensional stability for reliable measurements A hardened special steel construction and a rectangular 35 x 9 mm cross-section deliver a favourable stiffness-to-weight ratio across the full span. That balanced profile minimises bending and thermal drift during routine use, which supports repeatable results in bench checks and assembly verification. The block's mass of approximately 4 kg provides stable contact during measurement while remaining manageable for single-operator handling with appropriate aids. Traceability, conformity and integration into quality systems Conformity to DIN EN ISO 3650 ensures the length standard integrates smoothly into calibration chains and quality documentation. The specification Grade 0 indicates tight geometric tolerances suitable for reference instrumentation and master gauges. When used as a master for comparative measurements or as a benchmark for gauge verification, this block supports consistent process control and long-term reproducibility in production or metrology labs. Choose the Metav IndustryLine 1,000 mm gauge block for reproducible master measurements — contact Metav Werkzeuge in Emmerich for specification support and supply. Technical data Article number: M320.999.0 GTIN: 4054469132600 Tariff code: 90173000 ECLASS: 21170108 Core specifications Nominal length: 1,000 mm Cross-section: 35 x 9 mm Weight: 4 kg Grade: 0 Materials & features Material: hardened special steel Standard: DIN EN ISO 3650 Category: End gauges / gauge blocks Brand: Metav IndustryLine FAQ What level of accuracy does this length standard provide? The length standard is manufactured to DIN EN ISO 3650 and specified as Grade 0, providing tight tolerances intended for use as a master reference in calibration and inspection. Can the 1,000 mm gauge block be used as a master for comparative measurements? Yes — the 1,000 mm gauge block from Metav IndustryLine is intended for use as a master reference in comparative setups and master checks where a long, stable reference length is required. What are the material and handling considerations for this gauge block? The block is made from hardened special steel with a 35 x 9 mm profile; its mass and stiffness reduce bending under load, but handling with appropriate supports or two-person assistance is advised for consistent placement and to avoid damage. Is this product suitable for integration into an accredited calibration routine? Conformity to DIN EN ISO 3650 makes this gauge block suitable as part of accredited calibration and quality assurance processes; check laboratory procedures for specific handling and environmental requirements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Gauge Block Grade 1, DIN EN ISO 3650, Hardened Special Steel 35x9mm - Metav IndustryLine
Take advantage of a DIN EN ISO 3650 Grade 1 reference that combines long-term stability, a clear nominal length and robust construction for reproducible shop‑floor measurements; order the gauge via Metav Werkzeuge or consult the team for integration into existing calibration routines. End gauge 1000 mm (Grade 1) — DIN EN ISO 3650, hardened special steel End gauge 1000 mm (Grade 1) is a precision length reference designed for laboratory and workshop verification tasks, offering a stable baseline for length checks and fixture set‑up. DIN EN ISO 3650 Grade 1 accuracy 1000 mm nominal length, precise reference Hardened special steel for stable measurement Cross-section 35 x 9 mm, robust profile Reproducible accuracy for quality assurance A certified Grade 1 end gauge manufactured to DIN EN ISO 3650 provides a reliable reference for routine verification and calibration workflows. As a length standard, it supports the traceability chain by offering a defined, repeatable datum that reduces measurement variation in production checks. The compliance with the relevant norm communicates measurable conformity rather than subjective claims, making the gauge suitable for workshops and small calibration labs that require documented, consistent results. Solid construction that keeps reference values stable Constructed from hardened special steel with a compact 35 x 9 mm cross-section, the profile aims to combine rigidity with manageable handling weight. The material choice and heat treatment lower wear on the contact surfaces and preserve the geometry under normal workshop use, allowing the gauge to remain a dependable reference over many cycles. The gauge’s nominal 1000 mm length is presented in a robust, easy-to-mount form that integrates with measuring fixtures and inspection layouts where a stable straight edge and length datum are required. Practical use cases and workflow advantages In production and incoming inspection, this end gauge serves as a clear, measurable baseline for setup, quick checks or comparative measurements with portable indicators and jigs. The item’s design simplifies repeat checks, helping to shorten setup times and to maintain consistent part tolerances across batches. Identified by SKU M320.999.1 and GTIN, the gauge is also straightforward to reference in procurement and inventory systems, supporting administrative traceability alongside physical measurement traceability. For precision references from Metav IndustryLine, contact Metav Werkzeuge to reserve the Grade 1 1000 mm end gauge and discuss delivery or calibration options. Technical Data Article number: M320.999.1 GTIN: 4054469132617 Manufacturer: Metav IndustryLine Facts Nominal length: 1000 mm Cross-section: 35 x 9 mm Weight: 4 kg Customs tariff number: 90173000 Accuracy grade: 1 Special features Material: hardened special steel Standard: DIN EN ISO 3650 Robust profile for workshop use Suitable as a reference length standard FAQ What level of accuracy does this end gauge provide? The end gauge meets DIN EN ISO 3650 Grade 1 requirements, providing a precise reference level appropriate for many workshop and calibration tasks. Is the 1000 mm gauge suitable for routine setup and production checks? Yes, the 1000 mm nominal length and sturdy 35 x 9 mm profile make it well suited for fixture set‑up, comparative checks and repeatability controls on the shop floor. What material is used and how does that affect longevity? Made from hardened special steel, the gauge resists surface wear and maintains geometry under normal inspection use, which supports long service life for a stable reference. Can the gauge be tracked in procurement and inventory systems? Yes. The item is listed under SKU M320.999.1 and GTIN 4054469132617, facilitating ordering and inventory control. Which environments is the gauge intended for? The gauge is intended for laboratory and workshop environments where a durable, norm‑conforming length reference is required for quality assurance and setup tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm End Gauge Holder Very Sturdy Design - Metav IndustryLine
Take advantage of the combination of robust construction, a precise 0–100 mm clamping range and compact handling to secure reproducible measurement results. Order this end gauge holder directly via Metav Werkzeuge or ask our consultants for application advice. End gauge holder 0–100 mm — Robust clamping, Metav IndustryLine The End gauge holder 0–100 mm secures gauge blocks for precise measurement and calibration in workshop and laboratory metrology. Very robust construction Clamping range 0–100 mm Compact, lightweight at 0.4 kg Suitable for precise calibration tasks Repeatable clamping for reliable measurement results A stable clamping device is the basis for reproducible results in any inspection routine. The holder is designed for robust fixation of end gauges and gauge blocks, reducing slippage and ensuring consistent contact geometry across repeated measurements. With a clear 0–100 mm range and a compact build, the unit minimises setup time and mechanical variables that typically cause measurement drift. The result is an efficient inspection workflow that maintains traceability and supports quality control procedures. Ideal for compact metrology and calibration benches This holder is engineered for benches where space and access are limited but accuracy remains essential. The compact design and low mass of 0.4 kg make handling straightforward while preserving stiffness where it matters: at the clamping interface. That combination benefits tasks such as small-part gauging, calibration of comparators, and fixture alignment, where ease of positioning and steady support translate directly into time savings and fewer re-measurements. Built for workshop durability and precise adjustment Constructed to withstand routine use, the holder features a very stable design that copes with workshop environments without sacrificing precision. The robust build reduces the need for frequent readjustment and helps protect gauge block surfaces during handling. As a Metav IndustryLine product, the component is intended to integrate into existing metrology equipment and inspection processes, offering a practical compromise between laboratory precision and shop-floor resilience. For robust 0–100 mm gauge holding and dependable measurement reproducibility, contact Metav Werkzeuge for product advice or to arrange procurement through Metav Werkzeuge. Technical data Article number: M317.204 GTIN: 4054469127507 eClass: 21170108 Customs tariff: 90173000 Facts Measurement range: 0–100 mm Weight: 0.4 kg Cross-section: bis 300mm 30x5mm und ab 300mm 30x6,7mm Special features Very robust construction Designed for end gauges / gauge blocks Compact format for bench use Category: End gauges FAQ What is the clamping range of the holder? The clamping range is 0–100 mm, suitable for common end gauges and gauge blocks used in small-part inspection. Is the holder suitable for calibration tasks on a workshop bench? Yes, the holder is designed for precise calibration work and stable repeatability in workshop and bench environments. Which Metav SKU identifies this product? This product is listed as M317.204 under the Metav IndustryLine range. How heavy is the device and does it require special mounting? The unit weighs 0.4 kg and is compactly designed for manual placement on calibration benches; no special mounting is required for standard use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Gauge Jaws for End Gauge Holder Pair 9×17 Cross‑Section, New Design - Metav IndustryLine
Take advantage of the precise mounting dimensions and the pairing format to improve setup speed and measurement repeatability; the compact 100 mm length and defined cross-section support consistent integration into existing end-gage holders. Order the planar jaws directly via Metav Werkzeuge or request compatibility advice from our consultants. Planar jaws for end gage holder (pair) — 100 x 9 x 19 mm, new design — Metav IndustryLine Planar jaws for end gage holder (pair) are mounting jaws developed for use on end-gage holders and inspection fixtures, offering a compact 100 mm working length and defined attachment geometry for repeatable positioning. Pair for end-gage holder Mounting 100 x 9 x 19 mm Cross-section 9 x 17 mm Precise mounting for consistent measurement results The pair of mounting jaws is engineered to provide repeatable positioning when used with standard end-gage holders, reducing setup variation between measurement cycles. The clearly defined mounting dimensions 100 x 9 x 19 mm ensure mechanical compatibility with common holder designs, which simplifies retrofitting and avoids custom machining. By fixing the contact geometry, the jaws help to maintain consistent measurement conditions across batches, supporting faster inspection throughput and fewer readjustments on the measurement bench. Easy integration and efficient workshop handling With a compact length and a paired set, these jaws are straightforward to install and exchange during routine inspections. The compact 100 mm length minimises overhang while still providing sufficient contact area for many workshop and bench tasks, combining space-efficient design with practical usability. Fewer handling steps and clearly indexed attachment points translate into time savings on repetitive tasks, thus contributing to reduced downtime and smoother production flow. Robust design that supports dependable results Although specific material details are not provided in the product data, the component is delivered as a matched pair and described as a new design, indicating an update aimed at improved fit and stability. The known cross-section of 9 x 17 mm and the lightweight characteristic of the set (0.2 kg) make it suitable for precise fixtures where low added mass is beneficial. The balanced combination of reduced mass and stable geometry helps to preserve measuring accuracy and makes the set appropriate for routine metrology and inspection applications. Practical advantages for workshop and quality assurance Supplied as a set of two, the jaws eliminate the need for individual sourcing of mating parts and support standardised fixture configuration. The compact format improves accessibility in tight setups and the fixed mounting pattern helps to speed up tool changes and minimise operator-induced variance. These attributes support clearer comparability of measurement results and contribute to consistent quality control procedures. For direct procurement or bespoke compatibility advice regarding the Metav IndustryLine planar jaws, contact Metav Werkzeuge in Emmerich and request guidance from our product consultants for fast, reliable supply. Technical Data Article number: M317.113 GTIN: 4054469127422 Label: Planschenkel für Endmaßhalter, Paar Aufnahme 100 x 9 x 19 mm NEUE AUSFÜHRUNG!!! Manufacturer brand: Metav IndustryLine Facts Length: 100 mm Cross-section: 9 x 17 mm Mounting dimensions: 100 x 9 x 19 mm Weight: 0.2 kg Pieces per set: 2 Tariff number: 90173000 ECLASS: 21170108 Special features Supplied as a matched pair for end-gage holders New design for improved fit and stability Intended for workshop and inspection fixtures Compact format for tight installation spaces FAQ Are these jaws compatible with standard end-gage holders? The planar jaws are designed with mounting dimensions 100 x 9 x 19 mm, enabling compatibility with end-gage holders that accept that attachment geometry; confirm the holder's mounting interface before installation. What is included in the delivery? Delivery comprises a matched pair of planar jaws (two pieces) as described under the Metav IndustryLine designation M317.113. How heavy is the set and does mass affect measurement stability? The set weighs 0.2 kg; the low mass supports ease of handling while the defined geometry aids measurement stability by reducing unwanted overhang and vibration. Is this a new design compared with previous versions? The item is offered as a new design version, intended to improve fit and repeatability when mounted in compatible end-gage holders. Can these jaws be used for large workpieces? The 100 mm length and compact cross-section are optimised for smaller to medium-sized inspection setups; for very large components, consider fixtures or jaws with greater reach or alternative mounting strategies. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
103 Piece Gauge Block Set, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine.
Take advantage of a hardened special steel design and conformity to DIN EN ISO 3650 for reliable end-measurement tasks; the comprehensive modular composition ensures flexible build-ups and long service life. Order the Parallel gauge block set M318.103.2 directly via Metav Werkzeuge or ask our consultants if technical clarification is required. Parallel gauge block set M318.103.2 — hardened special steel, DIN EN ISO 3650 Parallel gauge block set M318.103.2 is a precision end-measurement solution for calibration, assembly and inspection tasks in machine shops and metrology laboratories. Hardened special steel construction Conforms to DIN EN ISO 3650 Modular composition for build-up measurements Faster inspection through standardised precision The set delivers measurable improvements to quality-control throughput because each element is manufactured from hardened special steel, giving consistent surface quality and minimal wear. Conformity to DIN EN ISO 3650 guarantees that the dimensions and tolerances meet recognised European standards, which simplifies the integration of these elements into existing calibration and inspection routines. As a result, batch checks and comparative inspections run with fewer interruptions and greater predictability, supporting lean production processes and shorter cycle times. Durable materials that reduce recalibration frequency Because the blocks are produced in hardened special steel, abrasion resistance and long-term flatness are prioritised. This material choice translates into reproducible measurements over extended service intervals and reduces the frequency of corrective maintenance. For workshops where downtime is costly, the robustness of the components means stable reference lengths for assembly jigs and final inspections, while the nominal mass and machining quality assist in maintaining thermal stability during routine use. Modular build-ups for practical workshop use The composition is designed for rapid combination into a wide range of nominal lengths, so common measuring tasks no longer require bespoke gauges or time-consuming set-up. The modular approach supports efficient assembly measurement and in-process checking; technicians can construct the required nominal dimensions quickly and repeatably. This flexibility improves machine-setup times and lowers the likelihood of rework by providing accurate reference lengths at the point of need. Clear traceability and shop-floor value Selecting a set that conforms to industry standards simplifies documentation and traceability within a quality-management system. The construction and standard conformity support consistent internal audits and offer a dependable baseline for comparative checks. For procurement and inspection teams, the combination of hardened construction and DIN EN ISO 3650 compliance represents a pragmatic balance of long-term value and operational reliability. For procurement or technical advice about the Metav IndustryLine gauge block range, contact Metav Werkzeuge in Emmerich — info@metav-werkzeuge.com or call +49 2822 7131930 — to discuss how the hardened, standards-compliant composition fits specific inspection workflows. Technical data Article number: M318.103.2 GTIN: 4054469127880 Material: Special steel, hardened Standard: DIN EN ISO 3650 Pieces per set: 103 Weight: 3.3 kg Customs tariff number: 90173000 Facts Weight in kg: 3.3 Pieces: 103 GTIN numeric: 4054469127880 Special features Hardened special steel construction Conformity with DIN EN ISO 3650 Modular set for build-up measurements Category: Endmasse (gauge blocks) FAQ What standard does this gauge block set follow? The Parallel gauge block set M318.103.2 from Metav IndustryLine is manufactured to DIN EN ISO 3650, ensuring the dimensions and tolerances meet the applicable European specification for gauge blocks. Is the material suitable for frequent workshop use? Yes. The blocks are made of hardened special steel, which offers good wear resistance and dimensional stability for repetitive measurement tasks and routine inspection. Can this set be used to create different nominal lengths? The modular composition of the Metav IndustryLine set supports rapid build-up combinations, allowing versatile nominal lengths for assembly checks and calibration aids. What is the article number for ordering and documentation? Order and reference the set using Article number M318.103.2 when placing orders or recording the item in inventory systems. Is information on weight and customs classification available? The set weighs 3.3 kg and the customs tariff number is 90173000, which can be used for shipping and customs documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
103 Pieces Gauge Block Set 1.005–49 mm Hardened Special Steel DIN EN ISO 3650, In Case - Metav IndustryLine
Combine DIN EN ISO 3650 conformity with hardened special steel and a comprehensive gauge selection to ensure dependable reference measurements and reproducible workshop quality control. Order the set directly via Metav Werkzeuge or consult our specialists for tailored selection advice. Parallel end gauge set M318.103.0 — 103-piece parallel end gauge set, hardened special steel (Metav IndustryLine) The Parallel end gauge set M318.103.0 is a precision parallel gauge block set designed for dimensional reference, master measurements and calibration tasks in quality control and workshop environments. 103-piece comprehensive set Hardened special steel for long service life DIN EN ISO 3650 compliant Workshop-grade, stable construction Reliable reference standard for everyday metrology This parallel gauge collection provides a stable reference for assemblies, jigs and inspection fixtures, combining proven geometry with wear-resistant material. Manufactured to DIN EN ISO 3650, the blocks serve as a traceable baseline for comparative checks and setup tasks. The hardened special steel body reduces deformation under repeated use, so measurements remain reproducible over time. For operations that value repeatability, the set shortens adjustment cycles and supports consistent process control. Practical benefits for production and inspection Designed for hands-on workshop use, the gauges simplify common procedures such as setting runout tolerances, verifying parallelism and creating master gauges for go/no-go checks. The compact format and robust finish mean handling is straightforward while the geometry minimises measuring errors due to seating or tilt. As a result, throughput improves: fewer rechecks, faster setup and a lower risk of scrap. The construction also eases cleaning and maintenance, which preserves the reference surfaces and maintains measurement integrity. Integration into quality workflows and asset management As a complete set, these parallel end gauges provide the coverage needed for a wide range of reference tasks without constant tool changes. The moderate total weight and balanced sizing support safe storage and straightforward handling during inspections. Documentation-friendly labelling (SKU and GTIN) simplifies inventory control and traceability within calibration schedules. Choosing a standardised set manufactured to an established norm helps harmonise internal procedures and supports supplier audits and acceptance tests. Choose Metav IndustryLine precision and contact Metav Werkzeuge for expert selection support and reliable supply from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M318.103.0 GTIN: 4054469127866 Pieces per set: 103 Weight: 3.3 kg Facts Tariff number: 90173000 Eclass: 21179208 Category: End gauges / Measuring instruments Special features Material: Special steel, hardened Standard: DIN EN ISO 3650 Set type: Parallel end gauge set Packaging: Set delivery in a transportable container FAQ What standard does the set follow? The set conforms to DIN EN ISO 3650, ensuring standardised geometry and suitability for routine reference tasks with traceable manufacturing specifications. What material are the gauges made from? The parallel end gauges are manufactured from hardened special steel, providing durability and resistance to wear during repeated use. Which applications are typical for these gauges? Typical uses include master measurements, fixture setup, verification of parallelism and benchmarking components in production and inspection processes. How many pieces are included and how does that help workshops? The comprehensive 103-piece arrangement offers broad coverage for common reference combinations, reducing the need for frequent substitutions and accelerating setup operations. Is the overall weight suitable for benchtop use? With a total mass of approximately 3.3 kg, the set is compact enough for benchtop handling while remaining robust for regular workshop operation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
103 Pieces Parallel Gauge Block Set Hardened Special Steel DIN EN ISO 3650 Kitted Case - Metav IndustryLine
Benefit from the combination of hardened special steel, adherence to DIN EN ISO 3650 and a comprehensive configuration that delivers repeatable reference measures for workshop and production use. Secure the Parallel gauge block set directly via Metav Werkzeuge or consult their technical advisors for specification matching. Parallel gauge block set 103/1 (M318.103.1) – 103-piece, hardened special steel, DIN EN ISO 3650 The Parallel gauge block set serves as a precision reference for dimensional calibration, inspection and machine set-up across workshop and production environments Hardened special steel construction Conforms to DIN EN ISO 3650 Comprehensive 103-piece configuration Delivered in protective transport case Stable reference values for reliable quality control Manufactured from hardened special steel, this gauge block set provides a stable material basis that resists wear and thermal distortion during routine use. Compliance with DIN EN ISO 3650 ensures that form and dimensional tolerances meet an established international benchmark, which simplifies integration into inspection procedures and quality documentation. The combination of a robust material and recognised standard reduces uncertainty in measurement chains and supports consistent production outcomes. Versatile build-up options reduce setup time The collection is designed as a comprehensive reference set so that a wide range of nominal dimensions can be realised by stacking individual blocks. This set versatility shortens machine set-up and inspection cycles by allowing quick assembly of the required nominal lengths, improving throughput and reducing the frequency of tool changes. For workshops and maintenance shops the practical consequence is faster repeatability and fewer interruptions during calibration and alignment tasks. Practical handling and organised storage for the workshop Delivery in a protective transport case keeps the block faces organised and protected during storage and transit, which preserves accuracy between uses. The set’s overall mass and compact footprint make it convenient to move within the production environment while maintaining traceability of individual pieces. Metav’s logistics and quality filtering ensure consistent fulfilment for European customers, supporting dependable supply and straightforward replacement when expansion of inspection capability is required. Contact Metav Werkzeuge in Emmerich for application advice and to secure the Metav IndustryLine Parallel gauge block set (M318.103.1) Technical Data Article number: M318.103.1 GTIN: 4054469127873 Weight: 3.3 kg Material: Special steel, hardened Standard: DIN EN ISO 3650 Set: 103 pieces Tariff number: 90173000 Facts Pieces per set: 103 Weight: 3.3 kg ECLASS: 21179208 Special features Conforms to DIN 861/1 and DIN EN ISO 3650 Delivered in protective plastic or wooden case for transport Hardened special steel construction Size composition: 1 × 1.005 mm; 49 × 1.01–1.49 mm; 49 × 0.5–24.5 mm; 4 × 25–100 mm FAQ Which applications suit this gauge block set? The Parallel gauge block set is intended for dimensional calibration, inspection and machine tool set-up in workshops and production; the hardened special steel and DIN EN ISO 3650 standard provide a reliable reference for routine measurement tasks. What material and standard does the product follow? The blocks are made from hardened special steel and are specified to DIN EN ISO 3650; the Metav IndustryLine Parallel gauge block set (M318.103.1) also aligns with the DIN 861/1 format. How is the set supplied and stored? The set is supplied in a protective transport case that keeps individual blocks organised and protected, facilitating safe storage and straightforward selection during measurement or set-up. Can this set be used for traceable calibration? The set conforms to DIN EN ISO 3650 for dimensions and tolerances; for laboratory traceability and accredited calibration a separate certification process must be arranged. What sizes are included in the set? The configuration comprises a broad distribution of block sizes: 1 × 1.005 mm; 49 × 1.01–1.49 mm; 49 × 0.5–24.5 mm; 4 × 25–100 mm, allowing flexible build-up measurements across a wide range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10mm Gauge Extension Set With 10/15/20/25/30mm Spacers, Aluminium Case - Metav IndustryLine
Combine a 10 mm master gauge connector with modular extensions (10/15/20/25/30 mm) and a protective aluminium case for a tidy, adaptable gauge stack that simplifies small-step measurement tasks. Order the set directly via Metav Werkzeuge or contact our consultants for tailored advice. M317.134 End gauge extension and connector set (10 mm master gauge, extensions 10–30 mm) – Metav IndustryLine The M317.134 End gauge extension and connector is a compact kit designed to link and extend end gauges, supplied in an aluminium case for secure transport and orderly storage 10 mm master gauge connector included Extensions 10 / 15 / 20 / 25 / 30 mm Supplied in robust aluminium case Compatible with end gauges with/without holes Extend measurement range with repeatable precision This extension kit brings a modular approach to gauge stacks: the integrated 10 mm master gauge mates with the incremental extensions 10/15/20/25/30 mm to build precise nominal lengths without the need to stock multiple full-length gauges. The short, standardised extension increments reduce cumulative error during stack-ups and help maintain repeatable measurements in quality control processes. The arrangement is particularly useful for task-driven workshops and inspection benches where adaptability and traceability of lengths matter. Robust organisation and transport for the workshop Delivered as a complete set in a dedicated aluminium case, the kit protects calibration surfaces and small parts during handling and storage. The case keeps the components organised and ready for rapid deployment in production or metrology rooms, reducing setup time between jobs. The compact design supports routine shop-floor use and eases safe transport between inspection stations while preserving the condition of gauge faces and mating surfaces. Easy integration into existing gauge systems Assembly is straightforward: the connector and extensions are intended for reliable joining of standard end gauges, including those with or without connection holes. This compatibility allows the kit to supplement existing gauge inventories rather than replace them, offering a cost-effective route to greater measurement flexibility. Where nominal lengths need to be changed frequently, the set speeds up adaptation and lowers the logistical burden of managing multiple fixed gauges. Contact Metav Werkzeuge for technical guidance or to arrange supply of the Metav IndustryLine M317.134 set; email info@metav-werkzeuge.com or call +49 2822 7131930 for personalised advice and delivery options Technical data Article number: M317.134 GTIN: 4054469157764 ECLASS: 21170108 ETIM: EC002219 Customs tariff number: 90173000 Facts Master gauge size: 10 mm Extension lengths: 10 mm, 15 mm, 20 mm, 25 mm, 30 mm Complete set contains items M317.131 and M317.132 Packaging: aluminium case Special features Connects end gauges with or without connection holes Modular extension system for flexible nominal lengths Compact kit for workshop and inspection use FAQ What is included in the M317.134 set? The M317.134 set includes a 10 mm master gauge element, extensions in 10/15/20/25/30 mm and a protective aluminium case, supplied as a complete kit for modular length assembly. Can these extensions be used with existing end gauges? Yes, the extension and connector kit is compatible with standard end gauges and can link gauges both with and without connection holes to form accurate nominal stacks. Is the kit suitable for shop-floor use? The aluminium case and compact components make the kit well suited to workshop environments where organised, robust storage and frequent handling are required. How does the extension system affect measurement accuracy? Using standardised small increments minimises cumulative stacking error and supports repeatable measurements when components are assembled correctly and handled with care. Which industries benefit most from this kit? Machine shops, toolrooms and inspection departments that require flexible nominal lengths and efficient gauge management will find the kit particularly useful. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Combine high wear resistance and Grade 1 conformity for dependable length standards; benefit from the compact 11 mm size and low mass for repeatable reference measurements and order the ceramic gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic gauge block 11 mm, Grade 1 (Metav IndustryLine) The Ceramic gauge block 11 mm, Grade 1 serves as a compact reference length for precision calibration and workshop quality control, delivering stable, repeatable measurements where a fixed standard is required. High-stability ceramic material Grade 1 accuracy to DIN 861/1 Nominal length 11 mm, small and precise Reliable reference accuracy for calibration workflows The gauge block is manufactured to Grade 1 tolerance under DIN 861/1, making it suitable as a reference for routine calibrations and comparative checks in metrology labs and production control. As a fixed-length standard, it simplifies traceable measurement routines and reduces the need for repeated adjustments: the clear conformity to an established grade supports consistent results across inspection cycles. The compact 11 mm size is particularly useful when short, precise reference lengths are required in fixture set‑ups or instrument verifications. Material benefits that support long-term stability Made from ceramic, this end standard combines dimensional stability with strong wear resistance, which contributes to prolonged service life as a reference artefact. Ceramic materials typically resist corrosion and are non‑magnetic, so the block remains resistant to environmental influences that can affect metallic standards. The low mass (approx. 0.018 kg) aids safe handling and rapid placement without introducing excessive contact force, supporting faster measurement sequences and reduced operator fatigue in repetitive tasks. Practical use in quality control and instrument checks Engineered as a simple, robust reference, the block fits neatly into standard gauge block sets or serves as an individual calibration artefact for height gauges, micrometers and comparator systems. Its small footprint enables placement in confined jigs and on measurement benches where larger standards would be impractical. Where short, traceable checks are part of a production line’s in‑process control, the block provides a compact solution for verifying instrument performance and maintaining process reliability. Clear labelling and supply chain confidence Supplied under the Metav IndustryLine range with a recognised SKU and GTIN, the standard integrates easily into inventory systems and calibration records. The clearly defined tariff number ensures straightforward customs and procurement handling for international operations. For facilities seeking to consolidate trusted measurement tools, this ceramic reference block forms a reliable element in a broader metrology toolkit that supports reproducible outcomes. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine ceramic gauge block into existing calibration routines or to discuss bulk supply and traceability documentation via +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M324.011 GTIN: 4054469143101 Tariff number: 90173000 Weight: 0.018 kg Material: Ceramic Nominal length: 11 mm Grade: 1 (DIN 861/1) Dimensions & measurable values Nominal length: 11 mm Mass: 0.018 kg Features & applications Category: Endmasse (gauge blocks) Small-format reference standard for calibration High wear resistance inherent to ceramic material Non‑magnetic, corrosion‑resistant performance FAQ What tolerance class does this gauge block meet? The ceramic gauge block meets Grade 1 tolerance according to DIN 861/1, providing a standard suitable for many calibration and quality‑control tasks. Is the material suitable for use next to magnets or in corrosive environments? Yes, the ceramic composition of the Metav IndustryLine gauge block is non‑magnetic and offers resistance to corrosion, making it appropriate for such conditions. How does the 11 mm size fit into a calibration routine? The compact 11 mm length is ideal as a short reference for comparator checks, quick instrument verifications and use in confined fixtures where larger standards are impractical. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11 mm Gauge Block Single-End, Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
The combination of Grade 0 accuracy, hardened special steel and an industry‑standard cross‑section ensures reliable length references for workshop and inspection use; take advantage of these features and order the single end measure directly via Metav Werkzeuge or consult our specialists for application support. Single end measure 11 mm — Grade 0, DIN EN ISO 3650 (Metav IndustryLine) A single end measure 11 mm designed as a compact, high‑precision length standard for workshop checks and calibration chains Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel for dimensional stability Nominal size 11 mm, cross‑section 35 x 9 mm Lightweight 11 g for convenient handling Precision where repeatability matters The gauge is manufactured to DIN EN ISO 3650, offering Grade 0 accuracy suitable for demanding workshop inspections and reference stacks. As a single length standard, this end measure provides a defined nominal of 11 mm, making it simple to combine with other blocks or use as a standalone reference. The compliance with a recognised standard reduces uncertainty in comparative measurements and supports consistent quality control across production runs. Material and geometry for long service life Constructed from hardened special steel, the block resists wear and maintains dimensional integrity under routine handling. The cross‑section specified for sizes above 10.1 mm is 35 x 9 mm, which balances rigidity and ease of manipulation: the section prevents excessive bending while remaining compact enough for tight setups. These choices reduce deformation risk and prolong the useful life of the length standard in a busy quality environment. Practical integration into inspection workflows With a mass of only 0.011 kg, the block is easy to position, stack and transport between measurement stations. Its nominal format simplifies documentation and traceability during standard checks, enabling faster cycle times in incoming inspection or spot checks on the shop floor. The uncomplicated geometry also means the block is compatible with common holders and gauge racks used in machine shops and toolrooms. Suitable uses and handling guidance This end measure serves as a reference for comparative measurements, master blocks in gauge sets, and for verifying measuring equipment where an 11 mm reference is required. Handling recommendations include storing the block in a clean, dry environment and avoiding direct knocks to maintain surface integrity. When incorporated into measurement chains, ensure contact faces are clean and mating surfaces are flat to preserve the declared accuracy. For precise procurement and application advice on the Metav IndustryLine single end measure 11 mm (SKU M319.110.0), contact Metav Werkzeuge GmbH in Emmerich — technical consultants are available at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: M319.110.0 GTIN: 4054469131603 ECLASS: 21170108 Facts Nominal size: 11 mm Cross-section: 35 x 9 mm Weight: 0.011 kg Grade: 0 Standard: DIN EN ISO 3650 Tariff number: 90173000 Special features Material: hardened special steel Category: End masses Nominal specification: single end measure FAQ What tolerance class does the block comply with? The single end measure is manufactured to Grade 0 tolerance according to DIN EN ISO 3650, ensuring tight dimensional limits for workshop and inspection use. Is the 11 mm block suitable for stacking with other gauge blocks? Yes, the 11 mm end measure is intended for use in reference stacks and is dimensioned for straightforward combination with other blocks that meet the same standard. What is the cross‑section for this nominal size? For sizes above 10.1 mm the cross‑section is 35 x 9 mm, providing enhanced rigidity for reproducible measurements. What material is used and why does it matter? The block is made of hardened special steel, chosen for wear resistance and long‑term dimensional stability under normal workshop handling. How should the block be stored to preserve accuracy? Store in a clean, dry place and avoid impacts; keep contact faces free of debris to maintain declared accuracy and repeatability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.5 mm Gauge Block Single End, Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Taking advantage of DIN EN ISO 3650 conformity, Grade 0 accuracy and a hardened special steel construction, this single gauge block offers a compact, reliable reference for traceable dimensional checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Single gauge block 11.5 mm — Grade 0, DIN EN ISO 3650 The Single gauge block 11.5 mm is a precision reference standard designed for laboratory and workshop calibration tasks, supplying a stable nominal length and reproducible contact faces for stacking and comparison measurements. DIN EN ISO 3650 Grade 0 accuracy Hardened special steel construction Compact 11.5 mm nominal reference Certified accuracy for dependable reference measurements Manufactured to DIN EN ISO 3650 and specified as Grade 0, this gauge block functions as a high‑quality reference standard for dimensional verification. The tight tolerance band of Grade 0 guarantees repeatable results when used for setting gauges, verifying calipers or building calibrated stacks. By relying on a recognised standard, quality control cycles become more efficient: fewer repeat measurements, faster decision making and reduced downstream rework. The nominal length of 11.5 mm is suitable for both direct comparison and as part of stacked combinations to reach intermediary reference lengths. Robust material and geometry for long-term stability Made from hardened special steel, the block provides wear resistance and dimensional stability under normal metrology handling. The larger cross‑section specified for sizes above 10.1 mm yields a 35 x 9 mm block profile, improving grip and resistance to twisting during use while keeping mass low at approximately 0.011 kg. These attributes combine to reduce measurement variability: the hard surface resists abrasion, the stable geometry minimises bending effects, and the compact mass limits thermal inertia, so the block reaches ambient temperature quickly for accurate comparative measurements. Practical benefits in calibration workflows In calibration laboratories and precision workshops the block serves as a reliable master for setting instruments and verifying production fixtures. As a single, durable reference the unit supports quick checks of go/no‑go gauges, comparator set‑ups and incoming inspection tasks, helping production teams maintain conformity without interrupting throughput. The compact format simplifies storage and handling, while the conformity to an established norm streamlines documentation and audit trails. For specialised applications or stack configurations, Metav Werkzeuge consultants can advise on compatible reference sets and traceability options. Secure traceable measuring references from Metav IndustryLine — contact Metav Werkzeuge for tailored advice and reliable supply. Technical data Article number: M319.115.0 GTIN: 4054469131627 SKU: M319.115.0 Facts Nominal size: 11.5 mm Weight: 0.011 kg Cross-section (for >10.1 mm): 35 x 9 mm Tariff code: 90173000 ECLASS: 21170108 Special features Grade 0 tolerance according to DIN EN ISO 3650 Hardened special steel material Compact reference for stacking and comparator use Category: Gauge blocks / End gauges Label: Single gauge block 11.5 mm, DIN EN ISO 3650, Grade 0 FAQ What accuracy class does this gauge block meet? The block conforms to DIN EN ISO 3650 and is specified as Grade 0, providing a high level of dimensional reproducibility suitable for laboratory and inspection tasks. Which material is used for the measuring faces? The Single gauge block 11.5 mm is produced from hardened special steel, chosen for its wear resistance and dimensional stability under regular metrology handling. How is this block typically used in a calibration routine? As a compact reference standard, the block is used alone for direct comparisons or combined in stacks to achieve required calibration lengths for instruments and gauges. Is the block suitable for shop‑floor verification or only for laboratory use? Designed for both environments, the gauge block supports workshop checks and laboratory calibration; its hardened faces and robust profile make it practical for routine inspection tasks. What are the exact dimensions and identification for ordering? Nominal length 11.5 mm, cross‑section 35 x 9 mm (for sizes above 10.1 mm), weight approx. 0.011 kg; Article number M319.115.0 and GTIN 4054469131627 identify the item. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.5mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of ceramic construction, Grade 1 accuracy (DIN 861/1) and compact 11.5 mm length for a corrosion‑resistant, stable length reference that supports reproducible inspection results. Order the gauge block directly via Metav Werkzeuge or consult the Metav team for further specification advice. Ceramic gauge block 11.5 mm, Grade 1 (DIN 861/1) — Metav IndustryLine The Ceramic gauge block 11.5 mm, Grade 1 (DIN 861/1) is a compact, high‑stability length standard intended for precision inspection, calibration benches and laboratory reference stacks. Ceramic material for corrosion resistance Grade 1 accuracy per DIN 861/1 Nominal length 11.5 mm for compact references Low weight 0.02 kg for easy handling Consistent reference accuracy for inspection and calibration A Grade 1 length standard certified to DIN 861/1 provides a reliable baseline for comparative measurements and tool setting. The compact 11.5 mm nominal length makes this block ideal where a short reference is required without sacrificing metrological reliability. As a stable artefact for gauge stacks, the block helps to maintain traceable measurement chains and reduces the need for frequent re‑adjustment of bespoke fixtures. The combination of a compact form and class‑rated accuracy supports faster inspection cycles and more predictable quality workflows. Material benefits that reduce measurement uncertainty Manufactured from ceramic, the block offers pronounced corrosion‑resistant behaviour and excellent surface hardness, which together preserve measuring faces under repeated use. Ceramics typically show low thermal expansion, which lowers short‑term length variation when ambient temperatures fluctuate; this supports consistent readings on the workshop floor and in controlled laboratory conditions. The wear characteristics of the material also contribute to long service life, so the artefact remains a stable reference over extended calibration intervals. Practical handling and integration into metrology routines The compact form factor and light mass simplify handling and stacking within a gauge block set or master reference stack. Gentle cleaning with a lint‑free cloth and storage in a dry, dust‑free environment prevent surface contamination and preserve the measuring faces. For traceable workflows, the block functions as a dependable standard for comparative checks, instrument verification and as a base for setting micrometre and comparator references. Metav’s logistics and quality filter in Emmerich ensure consistent availability for industry and workshop supply chains. For consistent, corrosion‑resistant length standards, contact Metav Werkzeuge to discuss the Ceramic gauge block 11.5 mm, Grade 1 (DIN 861/1) and arrange delivery from Emmerich. Technical data SKU: M324.011.5 GTIN: 4054469143118 Customs tariff number: 90173000 Category: Endmasse (gauge blocks) Label: Ceramic gauge block 11.5 mm, Grade 1 DIN 861/1 Facts Nominal length: 11.5 mm Weight: 0.02 kg Grade: 1 Material: Ceramic Special features Conformity: DIN 861/1 Corrosion‑resistant measuring faces Compact reference for gauge stacks Suitable for precision inspection and calibration FAQ What level of accuracy does this gauge block provide? The Ceramic gauge block 11.5 mm, Grade 1 (DIN 861/1) is manufactured to Grade 1 tolerances under DIN 861/1, providing a high‑precision reference suitable for standard inspection and calibration tasks. Why choose a ceramic block rather than a steel block? Ceramic construction offers better corrosion resistance and lower thermal expansion than many steels, so the gauge block retains its length more stably under varying ambient conditions and repeated handling. How should the block be cleaned and stored to preserve accuracy? Clean the block with a soft, lint‑free cloth; avoid abrasive cleaners and strong solvents. Store in a clean, dry environment away from humidity and contaminants to keep the measuring faces pristine. Can this block be used in a master gauge stack for comparative measurements? Yes, the compact 11.5 mm block is intended for use within gauge stacks and as a compact reference when building calibrated length standards for comparators and setting fixtures. Is the block suitable for workshop use or only for laboratories? The robustness and corrosion resistance of the ceramic material make the gauge block suitable for both workshop inspection benches and controlled laboratory environments where a compact, class‑rated reference is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.5mm Gauge Block Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
The precise combination of DIN EN ISO 3650 Grade 1 conformity, hardened special steel and a compact cross-section ensures reliable reference measurements and consistent handling in inspection and set-up tasks. Order the gauge directly via Metav Werkzeuge or consult the technical team for application advice. End gauge 11.5 mm — DIN EN ISO 3650 Grade 1, hardened special steel The End gauge 11.5 mm is a precision reference gauge intended for dimensional verification and master-measurement tasks in quality control and production environments, compliant with DIN EN ISO 3650 Grade 1. Nominal size 11.5 mm, DIN EN ISO 3650 Grade 1 Hardened special steel construction Cross-section 35 x 9 mm for sizes above 10 mm Consistent reference accuracy for inspection and production A reference gauge manufactured to DIN EN ISO 3650 and specified as Grade 1 provides a clearly defined tolerance band for calibration and verification routines. The nominal 11.5 mm value is produced to reproduceable limits, enabling its use as a master for setting micrometres, verifying plug gauges or confirming gauge blocks. This level of conformity reduces uncertainty in acceptance testing and supports quality procedures that rely on traceable dimensional standards. Robust material and geometry for repeatable handling Constructed from hardened special steel, the gauge delivers long-term wear resistance and dimensional stability. For diameters above 10.1 mm the sectional profile is 35 x 9 mm, a geometry that balances stiffness and ergonomic handling; this reduces the risk of bending during use and helps to maintain measurement integrity. At just 0.011 kg the piece is easy to position while still offering the rigidity expected of a reference standard. Practical benefits in workshop and laboratory use In workshops and inspection rooms the gauge serves as a fast, reliable reference for set-up and routine checks. Use as a master for micrometre setting, as a go/no-go reference in process control, or for comparative checks during first-article inspections. The clear standardisation and compact format support efficient workflows, minimise machine downtime and contribute directly to lower scrap and rework rates through faster decision-making. Care recommendations to preserve accuracy To retain the original specification, protect the gauge from impacts and corrosive environments; clean before and after use and apply a light protective oil when storing for extended periods. Store the gauge in a cushioned box or drawer away from temperature extremes and abrasive materials. For assistance on proper handling or to confirm suitability for a specific measurement task, Metav Werkzeuge's product specialists are available to advise on best practice. For purchases or application guidance on this Grade 1 reference gauge, contact Metav Werkzeuge GmbH to discuss suitability and delivery options via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M319.115.1 GTIN: 4054469131634 Weight: 0.011 kg Nominal size: 11.5 mm Standard: DIN EN ISO 3650 Grade: 1 Material: Special steel, hardened Tariff number: 90173000 Facts Cross-section (for this size): 35 x 9 mm Nominal mass value: 11.5 mm Weight (gross): 0.011 kg Special features Conforms to DIN EN ISO 3650 Grade 1 Hardened special steel for wear resistance Category: End gauges / Endmasse Intended use: Reference and verification in quality control FAQ What tolerance class does this reference gauge meet? The gauge is manufactured to DIN EN ISO 3650 Grade 1, providing tight, reproducible tolerances suitable for inspection and calibration tasks. Can this gauge be used to set micrometres and comparators? Yes, the End gauge 11.5 mm is suitable as a master for setting micrometres, comparators and for comparative checks in production control. What material is the gauge made from and why does that matter? The gauge is made from hardened special steel, which improves wear resistance and dimensional stability, ensuring consistent measurement performance over time. Is the cross-section relevant for handling and rigidity? The cross-section of 35 x 9 mm (applied for sizes above 10.1 mm) increases stiffness and provides secure handling during measurement, helping to maintain repeatability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
110mm End Gauge Connector With 10mm Base Piece And 10/15/20/25/30mm Extensions - Metav IndustryLine
Take advantage of the modular coupling that links a 125 mm end gauge with smaller gauges below 100 mm and provides an extendable range up to 110 mm; the unit includes a 10 mm passpiece and modular extensions for flexible incremental lengths. Order the coupler directly via Metav Werkzeuge or consult our specialists for application advice. M317.132 Gauge block connector — connector for 125 mm to sub‑100 mm gauges with modular extensions (Metav IndustryLine) The M317.132 Gauge block connector serves as a precision coupling solution for joining a 125 mm end gauge with smaller slip gauges below 100 mm, enabling an extendable assembly for workshop and inspection setups. Compatible with 125 mm and sub‑100 mm gauges Expandable coupling range to 110 mm Includes 10 mm fitting plus extensions Connector only — gauges not included Preserve measurement accuracy when combining sets The coupler offers a precision coupling that maintains alignment and repeatability when different gauge lengths must be combined. By providing a stable mechanical interface between a 125 mm block and smaller blocks, the accessory minimises handling time and avoids improvised joins that can introduce misalignment. The result is a reliable intermediary that supports consistent stack geometry and reduces setup variability in calibration benches and inspection rigs. Flexible, modular extensions for tailored lengths A modular extension system is built around a 10 mm passpiece with a range of removable extensions (10, 15, 20, 25 and 30 mm), allowing incremental length adjustments up to a total extendable range of 110 mm. This configuration permits precise adaptation of gauge stacks without the need for custom slip gauges, which speeds up measurement tasks and improves workshop efficiency. The modular approach supports straightforward assembly and replacement of individual increments as requirements change. Seamless integration into metrology workflows Designed for metrology and quality‑control environments, the connector is supplied as a dedicated coupling device — no gauge blocks are included — so it complements existing sets and avoids unnecessary duplication. The robust mechanical interface is intended for routine workshop use where quick configuration changes and reliable repeatability are priorities. For tasks requiring mixed‑length stacks or temporary length adjustments, the component reduces downtime and supports a more orderly calibration process. For advice on suitability, configuration or to obtain the M317.132 through Metav Werkzeuge, contact our Emmerich team for fast specification support and delivery guidance Technical Data Article number: M317.132 GTIN: 4054469157740 Tariff number: 90173000 Category: Gauge blocks Facts Max expandable range: 110 mm Base fitting: 10 mm Extension sizes: 10 mm; 15 mm; 20 mm; 25 mm; 30 mm ECLASS: 21170108 ETIM: EC002219 Special features Connector for joining 125 mm and sub‑100 mm end gauges Supplied as connector only — gauges not included Passpiece with modular extensions SKU: M317.132 FAQ Can the connector join a 125 mm gauge with a 90 mm gauge? Yes. The M317.132 gauge block connector is designed to couple a 125 mm end gauge with smaller gauges under 100 mm, providing a stable joint for mixed‑length stacks. What extension sizes are supplied with the connector? The connector includes a 10 mm passpiece and modular extensions in 10 mm, 15 mm, 20 mm, 25 mm and 30 mm increments to achieve the required assembly length. Is any calibration certificate included? The product is supplied as a connector only; no gauges or calibration certificates are included with this item. Will the connector affect repeatability of gauge stacks? When used correctly, the connector preserves alignment and supports repeatable setups, helping to maintain stack geometry and minimise setup variability. What is the maximum extendable length with all extensions fitted? With the supplied extensions assembled, the maximum extendable coupling range is 110 mm for mixed gauge configurations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
110x65x35 mm Foot for End Gauge Holder Very Sturdy Construction - Metav IndustryLine
Benefit from a very stable construction and compact dimensions that deliver repeatable calibration results and reduced measurement uncertainty; order the foot directly via Metav Werkzeuge or ask our consultants if needed. M317.211 – Foot for end gauge holder, 110 x 65 x 35 mm, very stable construction (Metav IndustryLine) A M317.211 foot engineered to provide a rigid support for end gauge holders in precision metrology and calibration environments. Very stable construction for repeatable measurements Compatible with series 317.20X holders Compact footprint 110 x 65 x 35 mm Solid 1.2 kg mass for vibration damping Solid base that boosts measurement consistency The rigid base reduces micro-movements during contact and is therefore crucial for repeatable calibration cycles. With external dimensions of 110 x 65 x 35 mm and a mass of 1.2 kg, this foot provides a low centre of gravity and passive vibration damping, making measurements less sensitive to ambient disturbances. The robust build, described as very stable construction, supports consistent results when paired with end gauge holders and eliminates the need for frequent repositioning, which shortens set-up time and improves throughput in routine quality checks. Compatibility that simplifies workshop workflows Designed for integration with the 317.20X holder family, the foot fits directly to the corresponding holders and supports standard end gauge setups. It is explicitly compatible with the caliper-type gauges identified as M317.203 and M317.206, ensuring straightforward replacement or retrofitting in existing benches. The compact footprint and predictable mechanical interface reduce fixture complexity and allow the metrology bench to remain uncluttered, which benefits both small workshops and larger inspection cells where space and reproducibility matter. Cross-section options explained for larger measuring ranges The foot accommodates bar cross-sections used with end gauges: for measuring lengths up to 300 mm the prescribed cross-section is 30 x 5 mm, while for larger spans the profile increases to 30 x 6.7 mm. This graduated cross-sectional approach improves profile stiffness where required and helps maintain alignment over longer measuring spans. Explaining this in practical terms: the thicker profile for larger gauges resists bending and ensures that dimensional references remain parallel, which in turn reduces measurement scatter in medium‑to‑large workpieces. Built for industrial use and routine calibration The component is manufactured to withstand regular handling on the shop floor and is suitable for integration into calibration routines. Its mass and geometry are chosen to deliver a stable reference without adding unnecessary bulk to the metrology station. As part of an end gauge system, the foot supports traceable, repeatable measurements and is suitable for daily quality control tasks as well as periodic calibration campaigns where mechanical stability is a prime requirement. For precise integration advice or to order the M317.211 foot for end gauge holders, contact Metav Werkzeuge to discuss compatibility with existing equipment and supply options. Technical data Article number: M317.211 GTIN: 4054469157382 Category: Endmasse Tariff number: 90173000 Facts Dimensions: 110 x 65 x 35 mm Mass: 1.2 kg Cross-section up to 300 mm: 30 x 5 mm Cross-section from 300 mm: 30 x 6.7 mm Special features Very stable construction Compatible with series 317.20X holders Suitable for use with M317.203 and M317.206 calipers Compact design for stable calibration setups FAQ What is the primary function of this foot? The foot serves as a rigid base for end gauge holders, providing mechanical stability for repeatable measurement and calibration. Which holders and calipers are compatible with the foot? Compatibility is specified for the 317.20X holder series and the caliper items M317.203 and M317.206; it is intended as a direct support for these configurations. How does the cross-section change with gauge length? For measuring lengths up to 300 mm the cross-section is 30 x 5 mm; for lengths beyond 300 mm the profile increases to 30 x 6.7 mm to preserve stiffness. Is the foot suitable for routine industrial use? Yes, the solid design and 1.2 kg mass ensure resistance to shop-floor disturbances and support routine calibration and inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
112 Gauge Block Set 112 Pc, Hardened Special Steel, DIN EN ISO 3650, Supplied In Case - Metav IndustryLine
Benefit from hardened special-steel construction and conformity with DIN EN ISO 3650 for dependable length standards; take advantage of the comprehensive set composition and protective transport case to streamline inspection routines — order directly via Metav Werkzeuge or consult our specialists if required. Parallel end gauge block set M318.112.0 — hardened special steel, DIN EN ISO 3650 the Parallel end gauge block set M318.112.0 provides a workshop-grade set of precision length standards suitable for inspection, tool setting and comparative gauging in mechanical and metrology environments Hardened special-steel construction Conforms to DIN EN ISO 3650 Delivered in protective transport case Reliable length standards that reduce rework The set comprises a comprehensive assortment of precision gauge blocks finished from hardened special steel, offering stable reference lengths for everyday measurement tasks. Delivered to the workshop as a complete set, the blocks reduce the need for frequent stack adjustments and minimise downtime caused by re-measuring. The material choice provides wear resistance and long-term dimensional stability, so calibration intervals can be planned with confidence and process reproducibility improves. Designed for organised measurement workflow Organisation and ease of use are built into the set: the blocks are supplied in a protective transport case that keeps gauges sorted and accessible. The compact arrangement supports fast selection during set-up or inspection, helping to shorten cycle times on the shop floor. At a total weight of 3.6 kg, the kit remains portable while offering a full range of reference lengths; this balance supports frequent use across benches or mobile inspection stations within a production area. Conformity and material traceability for confident decisions Compliance with DIN EN ISO 3650 signals that the block dimensions and surface characteristics meet recognised industrial requirements. Material specification as special steel, hardened gives an indicator of robustness and long-term behaviour under normal workshop handling. Identification data such as SKU and GTIN allow straightforward inventory control and traceability back to the supplier, supporting quality documentation and audits without ambiguity. For assured workshop precision and reliable traceability, order the Metav IndustryLine parallel gauge block set from Metav Werkzeuge or contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com / +49 2822 7131930 for tailored advice and fast supply Technical data Article number: M318.112.0 GTIN: 4054469127897 Customs tariff number: 90173000 Facts Pieces per set: 112 Weight: 3.6 kg Set composition (sizes): 1 × 1.0005 mm; 9 × 1.001–1.009 mm; 49 × 1.01–1.49 mm; 49 × 0.5–24.5 mm; 4 × 25–100 mm Special features Material: Special steel, hardened Standard: DIN EN ISO 3650 Delivered in protective transport case Set: complete parallel gauge block assortment SKU: M318.112.0 FAQ What is the material and finish of the blocks? The blocks are made from special steel, hardened, providing wear resistance and stable reference lengths for workshop use. Which standard do the gauge blocks conform to? Conformity is to DIN EN ISO 3650, ensuring the blocks meet recognised dimensional and surface requirements for gauge blocks. How many pieces are included and what is the set composition? The set contains 112 pieces; composition details include single fine grades and ranges from 1.0005 mm up to 100 mm as listed in the technical data. Is the set supplied ready for transport and storage? Yes — the blocks are supplied in a protective transport case, arranged to keep gauges organised and protected during handling. What identification codes are available for procurement and inventory? Use SKU M318.112.0 and GTIN 4054469127897 for ordering and inventory control Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
112 Gauge Block Set 112 Pieces Hardened Special Steel DIN EN ISO 3650, Case Included - Metav IndustryLine
Take advantage of the combination of 112-piece coverage, hardened special steel construction and conformity with DIN EN ISO 3650 for reliable length references across production and inspection. Order the set directly via Metav Werkzeuge or consult the Metav team for application guidance. Parallel gauge block set M318.112.1 — 112-piece, DIN EN ISO 3650 (Metav IndustryLine) The Parallel gauge block set, DIN 861/1 provides precision length references for calibration, setup and inspection tasks in machine shops and quality departments. 112-piece precision gauge block set Hardened special steel construction Conforms to DIN EN ISO 3650 Comprehensive size range for workshops Consistent precision for reproducible results The set functions as a calibrated reference system that supports repeatable spacing and datum generation for measurement and tooling tasks. Constructed from hardened special steel, the blocks deliver stable dimensional behaviour across typical workshop temperatures; the material choice reduces wear and helps retain gauge tolerances during repeated stacking and use. Conformity with DIN EN ISO 3650 provides a recognised standard for comparability in inspection routines and documentation, reinforcing process reliability and audit readiness. Coverage and usability that streamline inspection work A broad selection of sizes minimises the need for excessive combinations during setup, speeding routine checks and fixture alignment. The 112-piece composition supplies a practical granularity of step sizes and increments, which shortens configuration time for comparative and functional measurements. Stacking capability and flat, parallel faces enable accurate composite lengths; compact organisation of the set aids systematic retrieval and returns the workflow to productive tasks more quickly. Robust construction and long-term value Blocks manufactured from heat-treated tool steel withstand repeated handling and resist surface damage when used with proper care and lubrication. The tough finish and precision grinding maintain measurement integrity, reducing the frequency of replacement and preserving instrument investment over time. This durability, combined with the set’s standard compliance, supports traceable measurement practice and long-term quality assurance in production and maintenance environments. Contact Metav Werkzeuge for procurement and technical advice on the Metav IndustryLine gauge block sets — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical Data Article number (SKU): M318.112.1 GTIN: 4054469127903 EClass: 21179208 Facts Piece count: 112 Weight: 3.6 kg Tariff number: 90173000 Special features Material: hardened special steel Standard: DIN EN ISO 3650 Set composition: 1x1.0005 / 9x1.001–1.009 / 49x1.01–1.49 / 49x0.5–24.5 / 4x25–100 Product type: gauge blocks FAQ What applications are suitable for these gauge blocks? The Parallel gauge block set M318.112.1 is suitable for calibration, dimensional inspection, fixture setup and forming precise reference lengths in machine shops and quality labs. Is the set compliant with industry standards? Yes, the blocks conform to DIN EN ISO 3650, giving a standardised basis for length references and inspection protocols. What material are the blocks made from and why is that important? The set is manufactured from hardened special steel; this material provides wear resistance and dimensional stability under normal workshop conditions. How many pieces are included and does the set cover fine increments? The set contains 112 pieces and provides a comprehensive range of sizes and increments to reduce stacking complexity and speed measurement tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
112 Piece Parallel Gauge Block Set 1.0005–1.49 mm Hardened Special Steel DIN EN ISO 3650, Supplied in Case - Metav IndustryLine
Take advantage of the combination of high repeatability, DIN EN ISO 3650 conformity and robust hardened special steel for reliable set-up and inspection tasks; order this precision set directly via Metav Werkzeuge or contact our specialists for sizing advice. Parallel end gauge set 112/2 (112-piece) — hardened special steel, DIN EN ISO 3650 (Metav IndustryLine) The Parallel end gauge set 112/2 is a comprehensive set of hardened parallel end gauges designed for accurate setting, alignment and inspection in toolrooms, machine shops and quality control laboratories. 112-piece set to DIN standard Hardened special steel construction Supplied in protective transport case Precision that reduces rework and inspection time This set delivers consistent reference faces across a broad range of sizes, enabling reliable alignment and repeatable measurements during fixture set-up and inspection. Manufactured from hardened special steel, the gauges resist wear and maintain flatness under repeated use, which supports predictable tolerances and reduces the frequency of recalibration. The combination of material hardness and DIN conformity provides a technically sound basis for tighter process control and fewer production interruptions. Practical coverage for workshop and lab applications With 112 items covering fine increments and larger steps, the set is arranged to handle small to medium assembly tasks as well as routine calibration work. The assortment includes the fine-thickness pieces needed for precise stack builds and the larger parallels for setting up vises, fixtures and gauge blocks, ensuring the right element is available for diverse tasks. Delivered in a protective transport case, the set is organised for safe storage and rapid access, which helps maintain workflow efficiency on the shop floor. Compliance and traceability for quality systems Produced in accordance with DIN EN ISO 3650, the set meets recognized standards for end measures, making it suitable for integration into documented quality procedures. The standardised conformity supports traceable measurement practices that are often required in industrial quality management and supplier audits. Where repeatable production and documented inspection records are essential, this set offers a pragmatic combination of standard compliance and long-term durability. Contact Metav Werkzeuge for specification support or to arrange supply of the Metav IndustryLine parallel end gauge set — expert advice from Emmerich ensures the right set-up for your metrology needs Technical data SKU: M318.112.2 GTIN: 4054469127910 Category: End gauges / Parallels Data Pieces per set: 112 Weight: 3.6 kg Tariff number: 90173000 Material: Hardened special steel Special features Compliance: DIN EN ISO 3650 Set composition: 1×1.0005, 9×1.001–1.009, 49×1.01–1.49, 49×0.5–24.5, 4×25–100 Delivery: Supplied in protective transport case Design: Workshop and laboratory grade parallels FAQ What sizes are included in the set? The set contains 112 pieces in the composition 1×1.0005, 9×1.001–1.009, 49×1.01–1.49, 49×0.5–24.5 and 4×25–100 as supplied with the Metav IndustryLine parallel end gauge set Is the material suitable for long-term workshop use? Yes, the gauges are made from hardened special steel which provides wear resistance and long service life for routine workshop and laboratory use Does the set comply with an international standard? The set is manufactured to DIN EN ISO 3650, ensuring suitability for standardised inspection and traceability requirements Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11mm Gauge Block, Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of Grade 1 tolerance, DIN EN ISO 3650 conformity and a hardened special‑steel construction to secure reproducible reference checks in production. Order the gauge via Metav Werkzeuge or consult Metav's specialists for specification matching and rapid supply. End gauge 11 mm — Grade 1, DIN EN ISO 3650 (Metav IndustryLine) The End gauge 11 mm, Grade 1 is a compact, workshop‑grade reference for fast dimensional verification and setting of tools and fixtures in precision metrology. Grade 1 tolerance to DIN EN ISO 3650 Hardened special steel construction Precision nominal size 11 mm Proven reference standard for consistent checks The end gauge serves as a fast, traceable reference for go/no‑go checks and comparative verification. Manufactured to DIN EN ISO 3650 with Grade 1 tolerance, the item provides a clear normative basis for dimensional conformity control and minimises interpretation error during routine inspections. Because the gauge is a fixed nominal measure of 11 mm, it reduces set‑up time when adjusting jigs, tool holders or measuring equipment, which boosts throughput without compromising reproducibility. Robust design that withstands workshop handling A hardened special‑steel body provides resistance to wear and deformation while the compact cross‑section keeps the gauge easy to handle and store. The specified cross‑section dimensions (up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm) ensure adequate stiffness for accurate contact with mating surfaces. The low mass (approx. 0.011 kg) and compact form make the gauge convenient for bench use, while the heat‑treated material gives long service life under regular use — a pragmatic balance of durability and handling comfort for production and toolmaking environments. Practical benefits for procurement and process reliability As a fixed‑length master, the gauge simplifies routine verification tasks and supports both machine shop control and incoming‑inspection procedures. Labelling with a clear SKU and GTIN enables streamlined inventory and procurement; the compact format reduces storage footprint and transport effort. Supplied by Metav IndustryLine, the product fits into a broader strategy of accessible precision: consistent availability from the Emmerich stock reduces lead times and helps maintain uninterrupted measurement routines on the shop floor. For specification checks or to arrange supply through Metav Werkzeuge, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss the Metav IndustryLine end gauge and its suitability for specific inspection tasks Technical Data Article number: M319.110.1 GTIN: 4054469131610 Standard: DIN EN ISO 3650 Tolerance grade: 1 Material: hardened special steel Facts Nominal size: 11 mm Weight: 0.011 kg Tariff number: 90173000 Cross-section: up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm Special features Compact reference gauge for workshop checks Grade 1 accuracy for reliable comparative control Brand: Metav IndustryLine FAQ What accuracy can be expected from this end gauge? The Metav IndustryLine end gauge 11 mm (SKU M319.110.1) is manufactured to Grade 1 under DIN EN ISO 3650, providing the precision characteristics defined for this tolerance class and suitable reproducibility for workshop and inspection tasks. Is the gauge suitable for use as a setting master on machines? Yes. The hardened special‑steel construction and compact geometry make the gauge appropriate as a setting master for fixtures, toolholders and quick reference checks in machine and toolroom workflows. How should the gauge be stored to preserve accuracy? Store the gauge in a dry, stable environment and protect contact faces from grit and impact; the robust material resists wear but sensible storage extends service life and maintains measurement reliability. Can the gauge be used for routine incoming inspection? The Metav IndustryLine end gauge 11 mm is well suited to incoming inspection tasks as a fixed nominal reference for quick conformity checks and pass/fail decisions where a defined 11 mm standard is required. Which industries commonly use this type of gauge? Applications include precision engineering, toolmaking, small‑series production and quality control in mechanical workshops where a compact, normative reference for dimensional checks is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12 mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
The combination of a ceramic measuring surface, Grade 1 accuracy and a compact 12 mm nominal length delivers a stable, low-maintenance reference for routine calibration and shop‑floor checks. Order this calibrated-ready reference via Metav Werkzeuge or consult our technical advisors for application advice. Ceramic gauge block 12 mm, Grade 1 DIN 861/1 — precision ceramic gauge block by Metav IndustryLine Ceramic gauge block 12 mm, Grade 1 DIN 861/1 provides a compact, wear‑resistant length standard for precision inspection and length verification in laboratory and production environments Ceramic body for thermal stability Grade 1 accuracy (DIN 861/1) Nominal length 12 mm, compact reference Consistent reference for reliable length verification A compact gauge block with a 12 mm nominal length is ideal where a stable, easily handled reference is required. The ceramic construction offers inherent advantages for measurement stability: reduced sensitivity to short‑term temperature fluctuations compared with some metals and high surface hardness that limits wear. Specified as Grade 1 (DIN 861/1), this block supports repeatable checks of measuring equipment and setup verification, helping maintain production throughput through quicker, trustworthy confirmations of tool and instrument performance. Practical benefits on the shop floor and in the lab The compact format reduces handling errors and simplifies integration into existing inspection routines. As a small-format reference, it fits into precision toolsets and bench setups without occupying space, enabling rapid comparative checks and batch spot‑checks. The 12 mm block suits gauging of small features and can be combined with other standards for stack calibration routines. Its low mass and robustness make transport between workstations straightforward while preserving the dimensional reference required for efficient quality control workflows. Material advantages and care guidance Made from high‑purity ceramic, the block combines surface hardness and chemical inertness that minimise sticking, corrosion and abrasion in normal workshop environments. Routine maintenance is limited to keeping the faces clean and free from lubricants or filings; light wiping with a lint‑free cloth is normally sufficient. When used correctly as a length reference, the material properties of the block support long service life and consistent measurement performance, reducing the need for frequent replacement and thereby lowering total cost of ownership. Measurement context and suitable use cases Designed for metrology tasks where a compact, stable reference is required, this standard is suited to inspection benches, measuring microscopes, comparator setups and equipment verification. Its specification to DIN 861/1 positions it within recognised inspection procedures, enabling straightforward inclusion in documentation for quality audits. For customers seeking integrated measurement solutions, the block complements a wider range of gauge standards and precision instruments available from Metav IndustryLine. For reliable small‑format length references, contact Metav Werkzeuge to order this Metav IndustryLine ceramic gauge block or to request tailored application advice — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M324.012 GTIN: 4054469143125 Category: Endmasse / Gauge block Manufacturer: Metav IndustryLine Facts Nominal length: 12 mm Weight: 0.021 kg Grade: 1 Tariff number: 90173000 Special features Material: Ceramic Standard: DIN 861/1 Short description: Keramik-Endmaß 12 mm, Güte 1 FAQ What accuracy class does this gauge block meet? The ceramic gauge block meets Grade 1 according to DIN 861/1, providing a recognised tolerance class for routine verification and comparative measurement tasks. Is the material suitable for routine workshop use? Yes, the ceramic construction of the 12 mm block resists wear and is chemically inert, making it well suited to regular use in both workshop and laboratory environments when handled and stored correctly. Can this block be used together with steel gauge blocks? The 12 mm ceramic block may be used alongside steel standards for comparative checks; however, differences in material properties mean handling and stack protocols should avoid introducing contamination or uneven wear between materials. How should the block be cleaned and stored? Clean the faces with a lint‑free cloth and avoid oils or aggressive solvents; store in a dry, dust‑free container to preserve the measuring faces and maintain reference integrity. Which product and SKU should be referenced when ordering or documenting? Reference the Ceramic gauge block 12 mm, Grade 1 DIN 861/1 (SKU M324.012) by Metav IndustryLine for ordering and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12 mm Gauge Block Grade 1 DIN EN ISO 3650 Hardened Special Steel - Metav IndustryLine
Take advantage of a precisely engineered verification tool built from hardened special steel and conforming to DIN EN ISO 3650 Grade 1 tolerances; the compact 12 mm nominal size gives repeatable limit checks in tight inspection workflows. Order directly via Metav Werkzeuge or consult the Metav team for technical questions and availability. End gauge 12 mm — DIN EN ISO 3650 Grade 1, hardened special steel — Metav IndustryLine A End gauge 12 mm designed for fast go/no‑go checks and dimensional verification in workshop and quality‑control environments. DIN EN ISO 3650 Grade 1 tolerance Hardened special steel construction Compact 12 mm nominal size SKU M319.120.1, GTIN 4054469131658 Reliable compliance for inspection routines The instrument is manufactured to DIN EN ISO 3650, offering a Grade 1 tolerance band that supports consistent pass/fail decisions without elaborate measurement setups. For small components and production sampling, the compact 12 mm nominal size enables rapid insertion and verification, reducing cycle time at the inspection station. The standardised tolerancing simplifies documentation and audit trails, making this gauge suitable for shop‑floor checks where repeatability and adherence to recognised standards are required. Robust design that endures daily use Constructed from hardened special steel, the gauge resists wear and maintains its dimensional integrity under frequent handling. The cross‑section for nominal sizes above 10.1 mm is 35 x 9 mm, providing a stable profile that minimises bending and supports reproducible contact during limit checks. At approximately 0.011 kg, the piece is easy to handle while offering the necessary mass for secure placement in fixtures or when used by hand. The compact geometry and durable finish together ensure long service life and consistent performance in routine inspection tasks. Practical integration into quality processes As a purpose‑built limit gauge, this device streamlines incoming inspection, production sampling and quick end‑of‑line checks. The simple go/no‑go nature reduces training overheads and enables technicians to make rapid decisions that feed directly into process control. Clear material specification and normative compliance support traceability and technical documentation. Where finer metrological records are required, the gauge complements measurement equipment rather than replacing detailed micrometre or caliper readings, serving as an efficient first‑level control in a layered quality strategy. For supply, availability and tailored advice on Metav IndustryLine inspection tools such as this end gauge, contact Metav Werkzeuge in Emmerich for prompt assistance and delivery coordination. Technical data SKU: M319.120.1 GTIN: 4054469131658 Standard: DIN EN ISO 3650 Nominal size: 12 mm Tolerance grade: 1 Material: Special steel, hardened Weight: 0.011 kg Tariff number: 90173000 Numbers / Core technical data Nominal diameter: 12 mm Cross-section (for >10.1 mm): 35 x 9 mm Weight: 0.011 kg GTIN: 4054469131658 Tolerance grade: 1 (per DIN EN ISO 3650) Materials / Special features Hardened special steel Compliance: DIN EN ISO 3650 Category: End gauges Compact, rigid cross‑section for repeatable contact FAQ What standard does this gauge conform to? The gauge is manufactured to DIN EN ISO 3650, providing a Grade 1 tolerance suitable for standardised go/no‑go verification routines. Is the material specified for durability? Yes, the tool is made of hardened special steel, which preserves accuracy under frequent use and resists surface wear. Which nominal size and cross‑section apply to this SKU? The nominal size is 12 mm (SKU M319.120.1) and the cross‑section for nominal sizes above 10.1 mm is 35 x 9 mm, offering stable handling and contact. Can this gauge be used for routine shop‑floor checks? Absolutely; as an end gauge it is intended for quick pass/fail inspections and complements more detailed measuring instruments within a quality workflow. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12 mm Gauge Block, Hardened Special Steel, Grade 0, DIN EN ISO 3650 - Metav IndustryLine
Combine DIN EN ISO 3650 Grade 0 accuracy with a hardened special steel construction and a compact 12 mm nominal size for a stable, traceable reference in workshop and laboratory settings. Order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. End measure 12 mm (DIN EN ISO 3650) — Grade 0, hardened special steel — Metav IndustryLine The End measure 12 mm is a Grade 0 reference gauge designed for precision length standards and calibration tasks in industrial metrology and quality control. Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel for wear resistance Nominal size 12 mm for compact reference checks Cross-section for 12 mm: 35 x 9 mm Reliable reference for calibration and inspection As a Grade 0 reference to DIN EN ISO 3650, this gauge establishes a stable baseline for dimensional checks and tool calibration. The hardened special steel construction reduces wear and maintains consistent geometry over repeated use, which is essential when establishing traceable standards in a workshop or inspection room. The nominal 12 mm size and the robust 35 x 9 mm cross-section for this diameter give a favourable stiffness-to-mass ratio, helping to minimise deformation during handling and so preserving measurement integrity. Practical advantages for production and laboratory workflows Familiar workshop tasks benefit from a compact, high-precision reference that fits easily into inspection benches, setting-up kits or gauge sets. The compact format provides fast comparison checks and simplifies the setup of micrometres, callipers and comparators. The small mass (approximately 0.011 kg) reduces thermal inertia, speeding thermal equilibration when used in controlled environments. Combined with the Grade 0 tolerance, this makes the gauge suitable as a repeatable check standard for routine quality control and machine set-up. Confidence through standards and supply chain reliability Choosing a DIN-compliant reference delivers measurable assurance across supply and production chains: compliance with DIN EN ISO 3650 communicates a quantifiable tolerance class, easing acceptance in audits and incoming inspection. Supplied by Metav IndustryLine, the gauge benefits from Metav’s European logistics and technical support, backed by a broad product range and long-standing market presence. This combination supports a predictable procurement process and reduces the risk of non-conforming reference standards disrupting production. For laboratory-grade reference work, contact Metav Werkzeuge to source the Metav IndustryLine End measure 12 mm (SKU M319.120.0) or to obtain tailored specification advice for calibration and integration into existing measurement routines. Technical data SKU: M319.120.0 GTIN: 4054469131641 Weight: 0.011 kg Nominal size: 12 mm Tariff number: 90173000 Grade: 0 Numbers / Core technical data Cross-section (up to 10 mm): 30 x 9 mm Cross-section (from 10.1 mm): 35 x 9 mm Material: special steel, hardened Standard: DIN EN ISO 3650 Special features / Versions Compact reference gauge for calibration tasks Designed for reduced wear and dimensional stability Category: End measures (gauge blocks) FAQ What tolerance class does this gauge meet? The Metav IndustryLine end measure meets Grade 0 tolerances according to DIN EN ISO 3650, providing a high-precision reference for inspection and calibration. Is the material suitable for long-term workshop use? Yes, the gauge is made from hardened special steel, chosen to resist wear and preserve dimensional stability under routine handling. Can this gauge be used for setting micrometres and callipers? The 12 mm nominal size and robust cross-section make the gauge suitable as a compact reference for setting and verifying micrometres, calipers and comparator standards. What are the physical dimensions for handling and storage? For a 12 mm nominal size the applicable cross-section is 35 x 9 mm, and the item weight is approximately 0.011 kg, offering easy handling and quick thermal equilibration. What is the SKU for ordering and identification? This item is listed as M319.120.0 in the Metav IndustryLine range and carries GTIN 4054469131641 for inventory and procurement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
ensure traceable length calibration with gauge blocks
gauge blocks, also called slip gauges or end gauges, are precision length standards designed to transfer exact measures during calibration and setup. Manufactured and graded for metrological use, they provide the reference dimensions needed to verify and adjust measuring instruments in industrial workshops and calibration labs.
how gauge blocks work and where they are essential
gauge blocks are used to create known lengths by wringing individual blocks together or by using a single block as a reference. length calibration in industry commonly relies on parallel gauge blocks, while angle, cylinder and sphere end gauges serve specialised tasks. these blocks are produced in steel, ceramic or carbide, and their material choice balances wear resistance with thermal behaviour. regular calibration—typically performed annually—by DAkkS-accredited laboratories ensures traceability. the highest-precision reference work, class K, is certified by the PTB using laser techniques; classes 0, 1 and 2 are tested under progressively less controlled conditions (class 0 in a climate-controlled lab, class 1 in a standard measurement room, class 2 in production).
measurable benefits that cut downtime and uncertainty
- consistent, traceable length standards reduce rework and measurement disputes by enabling reliable instrument calibration.
- choosing the correct material (steel, ceramic, carbide) extends service life and limits wear in high-use environments.
- selecting the right accuracy class (K, 0, 1 or 2) matches calibration effort to application needs and avoids over‑specification.
- annual calibration by accredited labs maintains documented compliance and supports quality systems such as ISO.
why Metav is a smart partner for precision standards
Metav combines specialist knowledge with a broad range of measurement technology, making the procurement of gauge blocks straightforward and dependable. with over 48,000 customers and more than 250,000 products stocked from Emmerich, Metav acts as a pragmatic quality filter for European workshops, reducing supplier complexity and ensuring consistent supply.
In short, gauge blocks deliver traceable, material‑appropriate and class‑matched references that keep calibration workflows efficient and auditable.
faq
what materials are gauge blocks available in and why does it matter?
gauge blocks are typically supplied in steel, ceramic or carbide. material choice affects wear resistance, stability and thermal expansion; selecting the right material for your environment optimises longevity and measurement stability.
how often should gauge blocks be calibrated?
industry practice is an annual calibration cycle, carried out by DAkkS-accredited laboratories, though frequency can be increased depending on usage and required uncertainty.
what do the accuracy classes k, 0, 1 and 2 indicate?
the classes denote graded tolerances and test conditions: K is the highest precision (certified by PTB with laser measurement), class 0 is checked under climate-controlled lab conditions, class 1 in a normal measurement room and class 2 in production environments.
are parallel gauge blocks always used for length calibration?
yes; for length calibration the parallel gauge blocks are the primary standard because they provide exact planar faces for wringing and stacking to create precise lengths.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com