ADMT120408R-F56 WSM35G WSM35G Wendeplatten - Walter Tools
Combining the WSM35G Tiger‑tec Gold coating with the Parallelogram 85° geometry and the F56 chipbreaker provides stable chip formation and extended edge life in demanding machining of stainless and heat‑resistant alloys. Order this insert directly via Metav Werkzeuge or request tailored advice from our consultants. ADMT120408R-F56 WSM35G indexable milling insert — Tiger‑tec Gold for stainless steel and superalloys | Walter Tools The ADMT120408R-F56 WSM35G is an indexable milling insert engineered for reliable, high‑stability cutting in stainless steels and heat‑resistant superalloys and titanium applications. Tiger‑tec Gold coating, WSM35G grade Optimised for stainless steel and superalloys Parallelogram 85° insert geometry Chipbreaker F56 for stable chip control 0.8 mm corner radius for reliable edge life Robust coated grade for demanding alloys and elevated temperatures The combination of Tiger‑tec Gold coating and the WSM35G grade means the insert is designed to counteract the specific challenges of machining stainless steels and heat‑resistant alloys. These materials tend to work‑harden and generate higher cutting temperatures, which can cause built‑up edge and premature wear. A coated carbide grade with optimised coating architecture improves heat resistance and reduces adhesion at the cutting edge, resulting in more consistent flank wear progression and predictable tool life. In practice, this leads to fewer unscheduled tool changes and a more consistent production output. Geometry and chip control for consistent surface quality The Parallelogram 85° shape and the F56 chipbreaker are chosen to provide dependable chip formation and evacuation when machining ductile, heat‑sensitive materials. The insert’s 15° clearance angle supports secure entry and reduced rubbing on the workpiece, while the 0.8 mm corner radius balances edge strength with surface finish requirements. Effective chip control reduces rework and improves operator safety by diminishing stringy chips in stainless and nickel‑based alloys. These geometric choices support a reliable surface finish and repeatable dimensional results on each component. Production benefits: predictable tool life and process stability Stable cutting edges and controlled chip flow contribute directly to process reliability. The grade and geometry combination helps maintain a stable cutting edge, which reduces scatter in cycle times and decreases the risk of scrap. For production environments this translates into higher overall equipment effectiveness: fewer machine stoppages, improved first‑pass yield and lower indirect costs. From a cost perspective, predictable tool life enables better tool‑change planning and inventory management, strengthening both throughput and economic efficiency. Application guidance and integration into tool systems Designed as an indexable milling insert, the ADMT120408R‑F56 series integrates into standard cutter bodies compatible with Parallelogram 85° inserts. The grade is intended for ISO material groups M (stainless steels) and S (heat‑resistant superalloys / titanium), and the F56 chipbreaker supports operations where consistent chip segmentation is required. For selection, compare insert size, clamping type and corner radius with existing toolholders. If further machining data or cutting parameter recommendations are required, Metav Werkzeuge can provide application‑specific guidance to ensure optimal integration and performance. Contact Metav Werkzeuge for application advice, process recommendations or a tailored quote for Walter Tools ADMT120408R-F56 WSM35G inserts — phone +49 2822 7131930, eMail info@metav-werkzeuge.com Technical Data Article number: ADMT120408R-F56-WSM35G-WALTER Label: Fräswendeschneidplatte ADMT120408R-F56 WSM35G Walter Tools Manufacturer: Walter Tools Product type: Indexable milling insert Grade: WSM35G Series: Tiger‑tec Gold Key dimensions Free cutting angle: 15° Corner radius: 0.8 mm Insert size: 12 Thickness code: 04 Special features Parallelogram 85° insert geometry Chipbreaker: F56 Coated carbide grade (Tiger‑tec Gold) Material suitability: S / M Tolerance class: M FAQ What materials is this insert designed for? The ADMT120408R‑F56 WSM35G insert is optimised for ISO groups M and S — primarily stainless steels and heat‑resistant superalloys/titanium. How does the Tiger‑tec Gold coating help performance? The Tiger‑tec Gold coating on the WSM35G grade increases heat resistance and reduces adhesion, which supports stable chip formation and extends edge life during difficult cuts. Which chipbreaker is fitted and what benefit does it provide? This insert uses the F56 chipbreaker, which promotes consistent chip segmentation and evacuation, improving surface finish and reducing the risk of built‑up edge. Is the Parallelogram 85° geometry suitable for roughing and finishing? The Parallelogram 85° shape provides a versatile compromise between cutting engagement and edge strength, making it suitable for a range of operations when the correct cutting data are applied. How should the 0.8 mm corner radius be considered in process planning? The 0.8 mm corner radius strengthens the cutting edge for durable performance while still allowing acceptable surface quality; choose radius size based on the required edge strength and finish. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names remain the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The item offered is original factory‑new goods of the manufacturer.
ADMT120408R-F56 WSM45X WSM45X Wendeplatten - Walter Tools
Take advantage of the WSM45X coated carbide grade and the F56 chipbreaker for secure chip control and reliable cutting in stainless steel and heat-resistant alloys; this combination supports stable production and longer tool life. Order the insert directly via Metav Werkzeuge or consult our specialists for application advice. ADMT120408R-F56 WSM45X indexable milling insert – coated carbide for stainless steel and superalloys | Walter Tools ADMT120408R-F56 WSM45X is an indexable milling insert engineered for high thermal and mechanical stress applications, ideal for machining stainless steel and heat-resistant superalloys where chip control and edge stability are critical. Coated carbide grade WSM45X Optimised F56 chipbreaker Parallelogram 85° insert form 15° relief angle, 0.8 mm radius Consistent performance for demanding materials The WSM45X grade is a coated carbide specifically developed for difficult-to-machine materials. In practice, the grade promotes stable chip formation when machining stainless steel and heat-resistant superalloys, which are prone to work hardening and high cutting temperatures. The insert’s substrate and coating combination reduces the tendency for built-up edge, extending effective cutting life and lowering process variability. For shops aiming to increase throughput without compromising surface quality, this insert offers a reliable foundation for consistent results. Geometry that enhances cutting stability and surface finish The parallelogram 85° form and F56 chipbreaker are designed to work together to manage chip flow and cutting forces. The 15° relief angle reduces friction behind the cutting edge, while the 0.8 mm corner radius balances edge strength and accessible corner regrinding. These geometrical choices translate into fewer interruptions for de-burring and a predictable workpiece finish, making the insert suitable for production environments where repeatability and reduced secondary operations matter. Technical users will appreciate the clear link between geometry and reduced tool-induced vibration. Practical application and process advantages As an indexable insert from Walter Tools, this item supports fast replacement and minimal downtime in milling operations. The F56 chipbreaker helps break chips into manageable lengths, which benefits automated part handling and chip evacuation. Where high cutting temperatures and poor thermal conductivity of the workpiece present challenges, the coated grade contributes to process security by protecting the cutting edge against thermal degradation. For operations focused on lean manufacturing, this results in fewer tool changes and steadier cycle times. For machining stainless steel and superalloys with Walter Tools inserts, contact Metav Werkzeuge for supply and technical consultation via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: ADMT120408R-F56-WSM45X-WALTER Designation: ADMT120408R-F56 ISO designation: ADMT120408R-F56 WSM45X Manufacturer: Walter Tools Measurements / Core data Insert size: 12 Thickness: 04 Relief angle: 15° Corner radius: 0.8 mm Insert form: Parallelogramm 85° Chipbreaker: F56 Grade: WSM45X Features / Applications Coated carbide grade WSM45X Suitable for stainless steel (ISO group M) Suitable for heat-resistant superalloys and titanium (ISO group S) Tolerance class: M Series: Walter Schneidstoffsorte - Serie offen Execution: T FAQ Which materials is this insert intended for? The ADMT120408R-F56 WSM45X insert from Walter Tools is designed primarily for stainless steel and heat-resistant superalloys (ISO groups M and S), offering improved chip control and thermal resistance. What are the key geometric features that affect performance? The parallelogram 85° form, 15° relief angle and 0.8 mm corner radius on the ADMT120408R-F56 provide a balance of edge strength and accessibility, supporting stable cutting and good surface finish. How does the F56 chipbreaker benefit production? The F56 chipbreaker on this Walter Tools insert breaks chips into manageable segments, aiding chip evacuation and reducing the risk of entanglement in automated milling setups. Is this insert suitable for high-temperature applications? Yes; the WSM45X coated carbide grade in the ADMT120408R-F56 is formulated to withstand elevated cutting temperatures typical of stainless steel and superalloy machining, helping maintain process security. Can this insert be indexed to reduce downtime? The ADMT120408R-F56 is an indexable milling insert by Walter Tools, enabling quick indexation or replacement to keep machine uptime high and changeover times short. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
ADMT120408R-F56 WSP45G WSP45G Wendeplatten - Walter Tools
Benefit from the Tiger‑tec Gold PVD coating combined with the WSP45G grade for robust chip control and extended tool life; the parallelogram 85° form with a 0.8 mm corner radius and 15° relief angle delivers stable milling performance. Order the insert directly via Metav Werkzeuge or request guidance from our consultants for application optimisation. ADMT120408R-F56 WSP45G milling insert (Parallelogram 85°, 0.8 mm radius) – Walter Tools ADMT120408R-F56 WSP45G is a precision milling insert developed for productive face and profile milling in a wide range of materials Tiger‑tec Gold PVD coating for longer service life Versatile for Stahl, rostfreier Stahl and Titan (P/M/S) Parallelogram 85° form, 0.8 mm corner radius 15° relief angle for stable cutting action Maximum process reliability through coated carbide technology The combination of the Tiger‑tec Gold coating and the WSP45G carbide grade focuses on consistent performance under typical milling stresses. The multilayer PVD coating improves wear resistance and reduces friction at the tool–workpiece interface, which supports stable cutting conditions and lengthens tool life. In practical terms, the coated grade reduces the frequency of insert changes and contributes to predictable tool costs per component — an essential factor for high‑volume and continuous production environments. Geometry engineered for chip control and surface quality The parallelogram 85° insert form and the 0.8 mm corner radius are designed to balance strength and accessibility in milling applications. Combined with the F56 chipbreaker and a 15° relief angle, the geometry promotes controlled chip formation and evacuation, which minimises recutting and heat build‑up. For operators less familiar with chipbreaker function: the profile channels chips away from the cutting zone to prevent build‑up on the cutting edge, resulting in improved surface finish and reduced risk of built‑up edge on challenging workpieces such as Stahl, rostfreier Stahl or heat‑resistant alloys. Predictable performance and economic machining Tolerance class M and the standard thickness designation ensure repeatable seating and clamping in compatible toolholders, maintaining dimensional stability across tool changes. The insert size and thickness coding support straightforward tool selection and inventory management for toolrooms. Walter Tools’ grade selection aims to provide cost‑effective productivity: stable edge life decreases downtime, and the insert’s versatility across P/M/S groups simplifies tooling lists. For shops seeking to reduce process variability while maintaining component quality, this approach supports efficient cycle times and consistent results. For robust, versatile milling performance choose the Walter Tools ADMT120408R‑F56 WSP45G — contact Metav Werkzeuge for tailored cutting data and application advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: ADMT120408R-F56-WSP45G-WALTER Product designation: ADMT120408R-F56 WSP45G Manufacturer: Walter Tools Series: Tiger-tec Gold Grade: WSP45G Facts Relief angle: 15° Corner radius: 0.8 mm Insert form: Parallelogram 85° Insert size: 12 Thickness code: 04 Tolerance class: M Special features Coating: Tiger‑tec Gold (PVD) Chipbreaker: F56 Execution: T Material groups: P / M / S (suitable for Stahl, rostfreier Stahl, superalloys/Titan) ISO designation: ADMT120408R-F56 WSP45G FAQ What materials is this insert suitable for? The ADMT120408R‑F56 WSP45G is formulated for use across the P/M/S groups and is suitable for machining Stahl, rostfreier Stahl and heat‑resistant alloys such as Titan, as indicated by the WSP45G grade. How does the F56 chipbreaker influence milling performance? The F56 chipbreaker on the ADMT120408R‑F56 promotes controlled chip formation and efficient evacuation, reducing the risk of recutting and improving surface finish in interrupted or continuous milling operations. What advantages does the Tiger‑tec Gold coating provide? Tiger‑tec Gold enhances wear resistance and thermal stability for the WSP45G grade, helping to extend insert life and maintain consistent cutting-edge behaviour across longer tool cycles. Is the insert compatible with standard toolholders? The ADMT120408R‑F56 follows common ISO insert sizing and the tolerance class M, ensuring reliable seating and clamping in appropriately specified toolholders designed for parallelogram 85° inserts. What is the purpose of the 0.8 mm corner radius? A 0.8 mm corner radius on this milling insert offers a compromise between edge strength and achievable surface finish, providing robustness against edge chipping while maintaining acceptable form accuracy. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ADMT120408R-G56 WKP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WKP35G grade for reliable, long-lasting performance in Stahl and cast iron; order the insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. ADMT120408R-G56 WKP35G indexable milling insert — Tiger·tec Gold for Stahl and cast iron | Walter Tools ADMT120408R-G56 WKP35G is an indexable milling insert engineered for high-productivity machining in general industry, optimised for operations on Stahl and cast iron. Tiger·tec Gold coating technology Optimised chipformer G56 for stable chips Positive geometry with 15° relief angle Parallelogram 85° form for robust engagement Grade WKP35G: coated carbide for long life Boosted process security and throughput with coated carbide The combination of the Tiger·tec Gold coating and the WKP35G cutting grade provides a predictable wear pattern and extended tool life, which translates directly into higher uptime on the machine. Coated carbide is designed to withstand the thermal and mechanical demands of medium‑ to high‑speed milling, so the insert keeps edge integrity longer and reduces unscheduled tool changes. For production environments seeking consistent cycle times, this insert contributes to a measurable improvement in process reliability and overall equipment efficiency. Stable chip control for consistent surface quality The integrated chipformer G56 is shaped to break and evacuate chips reliably when machining common industrial materials. Stable chip formation reduces the likelihood of re-cutting and surface damage, which helps maintain a consistent finish with fewer rework steps. The 0.8 mm corner radius and the positive 15° relief angle together moderate cutting forces and support predictable engagement, especially in interrupted cuts or semi‑finishing passes, providing practitioners with a balanced combination of edge strength and surface integrity. Geometry and form that support flexibility in operations The parallelogram 85° insert form provides a secure clamping interface and favourable cutting directionality for many milling strategies, from shoulder cuts to helical entry. The modest corner radius offers a compromise between robustness and precision, while the plate thickness code and M tolerance class ensure dimensional consistency across batches. This geometry is particularly suited to tools where versatile cutting orientations are required, enabling shops to standardise on a single insert geometry for multiple tasks and thus simplify tool inventory. Application guidance and handling for predictable results Designed for use on ISO material groups P and K (Stahl and cast iron), the insert performs well in both continuous and interrupted milling when paired with appropriate carbide bodies and clamping systems. While the insert is optimised for common production metals, cutting data should be selected according to the specific machine, workpiece rigidity and coolant strategy. For precise speeds and feeds or for guidance on toolholder compatibility, Metav Werkzeuge’s consultants can provide tailored recommendations to translate the insert’s capabilities into reliable cutting parameters. For product enquiries or to specify the ADMT120408R‑G56 WKP35G insert for a particular application, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — our technical team will advise on selection and availability Technical data Article number: ADMT120408R-G56-WKP35G-WALTER SKU: ADMT120408R-G56-WKP35G-WALTER Series: Tiger-tec Gold Grade: WKP35G Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 0.8 mm Plate size: 12 Plate thickness: 04 Plate form: Parallelogram 85° Tolerance class: M Special features Material compatibility: P / K (Stahl, cast iron) Chipbreaker: G56 Cutting material: coated carbide (Tiger·tec Gold) Execution code: T FAQ What materials is this insert suited for? The ADMT120408R‑G56 WKP35G indexable milling insert from Walter Tools is formulated for ISO groups P and K, meaning it is suitable for machining Stahl and cast iron. What benefit does the Tiger·tec Gold series provide? Tiger·tec Gold coating on the WKP35G grade enhances thermal resistance and wear behaviour, extending edge life and supporting stable cutting in production milling. Is the ADMT120408R‑G56 suitable for interrupted cuts? Yes; the positive relief angle and the 0.8 mm corner radius give the insert a good balance of toughness and cutting precision, making it acceptable for many interrupted‑cut scenarios when mounted correctly. How does the G56 chipformer affect performance? The G56 chipformer is designed to produce short, controlled chips in typical conditions for Stahl and cast iron, reducing the risk of chip entanglement and improving surface consistency. Where can specific speeds and feeds be obtained? For machine‑ and application‑specific cutting data for the ADMT120408R‑G56 WKP35G insert, consult Metav Werkzeuge’s technical team who can recommend speeds, feeds and coolant strategies. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ADMT120408R-G56 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and an optimised G56 chipformer for stable chip control and extended tool life; order the insert directly via Metav Werkzeuge or consult our specialists for process optimisation. ADMT120408R-G56 / ADMT120408R-G56 WKP35S (WKP35S) milling indexable insert for steel and cast iron — Walter Tools (15° relief, 0.8 mm corner radius) A ADMT120408R-G56 WKP35S insert engineered for productive milling in ISO P and K applications, offering robust edge stability and consistent chip formation for industrial metalworking. Tiger-tec Silver coating Optimised G56 chipformer 15° relief angle 0.8 mm corner radius Boosted productivity through advanced coating and grade The combination of the Tiger·tec Silver coating and the WKP35S grade is designed to deliver higher wear resistance and reliable performance in mixed production environments. The coating technology reduces built-up edge and improves thermal stability, which directly translates into longer tool life and fewer index changes. For machining steel and cast iron, this translates into reduced downtime and a more predictable process window, supporting tighter production schedules and improved overall efficiency. Consistent chip control and improved process reliability The G56 chipformer is engineered to create short, controllable chips under the typical cutting conditions of P- and K-group materials. This targeted chip control reduces the risk of entanglement and workpiece damage, allowing for smoother automatic handling and easier post-process cleaning. Coupled with the 15° relief and Parallelogram 85° geometry, the insert provides a secure cutting edge with predictable force distribution, which benefits toolholders and machine spindle life through reduced vibration. Geometry designed for strength and surface quality With a 0.8 mm corner radius, the insert balances edge strength and surface finish, making it suitable for a range of slotting and shoulder milling tasks where robustness is required without compromising the machined surface. The parallelogram form gives a stable seating and enables advantageous cutting orientations for a variety of cutter bodies, while the tolerance class M supports consistent interchangeability. The result is a reliable milling solution that supports high-feed strategies and maintains dimensional accuracy across batches. For process advice or to secure the ADMT120408R-G56 WKP35S insert from Walter Tools, contact Metav Werkzeuge for tailored recommendations and ordering via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: ADMT120408R-G56-WKP35S-WALTER Name: ADMT120408R-G56 WKP35S Product type: milling indexable insert Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 0.8 Plate form: Parallelogram 85° Plate size: 12 Plate thickness: 04 Tolerance class: M Special features Coating: Tiger·tec Silver Grade: WKP35S (coated carbide) Chipformer: G56 Material suitability: Steel (P), Cast iron (K) Series: Tiger-tec Silver FAQ What materials is this insert suitable for? This insert is suitable for machining steel and cast iron as indicated by the WKP35S grade and the Tiger·tec Silver series. How does the G56 chipformer improve machining? The G56 chipformer provides controlled, short chips, enhancing process reliability and reducing risk of chip-related interruptions when milling steel and cast iron. What are the key geometric advantages of this insert? The parallelogram 85° shape with a 0.8 mm corner radius and 15° relief offers enhanced edge strength and stable seating for consistent cutting performance. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
ADMT120408R-G56 WSM35G WSM35G Wendeplatten - Walter Tools
The combination of a Tiger·tec Gold coating and the WSM35G grade delivers stable cutting edges and secure chip control for demanding materials; order the insert via Metav Werkzeuge or request application advice from Metav Werkzeuge consultants for optimal integration into existing processes. ADMT120408R-G56 WSM35G milling insert (Tiger·tec Gold) by Walter Tools — for stainless steels & superalloys The ADMT120408R-G56 WSM35G is a Tiger·tec Gold‑coated milling insert engineered for robust performance in the machining of stainless steels and heat‑resistant superalloys, offering secure chip formation and reliable edge life. Tiger·tec Gold coating for thermal stability Optimised G56 chipformer for secure chip control 15° relief angle for robust cutting performance Parallelogram 85° shape with 0.8 mm corner radius Consistent edge life through advanced coating technology The combination of the Tiger·tec Gold coating and the WSM35G cemented‑carbide grade is designed to resist thermal and mechanical loads encountered when machining demanding alloys. The multi‑layer coating provides a thermal barrier and improved surface hardness, which together reduce flank wear and delay crater formation under elevated cutting temperatures. This means fewer tool changes and a more predictable tool‑life curve, contributing directly to process stability and reduced machine downtime. Where high heat generation is an issue, the coated grade supports a consistent cutting edge and helps maintain dimensional accuracy of the workpiece. Geometry and chip control for safer machining The insert’s G56 chipformer and parallelogram 85° geometry improve chip breaking and evacuation in interrupted and continuous milling operations. The 15° relief angle reduces rubbing at the margin while the 0.8 mm corner radius increases edge strength, producing a favourable balance between surface finish and insert durability. These geometry choices are particularly beneficial during heavier cuts or when axial depths vary, as they reduce the risk of built‑up edge and stabilise cutting forces. Clear chip control lowers the chance of recutting and helps maintain consistent machining cycles. Tailored for stainless steels and high‑temperature alloys This grade is assigned to the ISO groups M and S, indicating suitability for stainless steels and heat‑resistant superalloys/titanium respectively. Such materials are prone to work hardening, poor thermal conductivity and sticky chip formation; the WSM35G grade compensates by promoting stable chip formation and maintaining a sharp, wear‑resistant edge. In practice, this enables more reliable machining of components that demand tight tolerances and good surface integrity. Where geometry permits, the insert supports operations that prioritise tool life and reproducible component quality. Practical benefits and selection guidance for production When integrating the insert into production, the main advantages are process reliability, reduced unplanned interventions and consistent surface quality, particularly on demanding alloys. Selection should consider machine rigidity, cutting parameters and the intended cut type: the insert is suited to medium to heavy milling, where the combination of the Tiger·tec Gold coating and robust chipformer delivers measurable uptime benefits. For specification matching or to confirm optimal cutting data, technical consultation with Metav Werkzeuge is recommended to align insert choice with machining strategy and production goals. Contact Metav Werkzeuge for tailored cutting data and application recommendations for Walter Tools Tiger·tec Gold inserts, or arrange a material‑specific consultation via Metav Werkzeuge. Technical data Article number: ADMT120408R-G56-WSM35G-WALTER Designation: ADMT120408R-G56 WSM35G Manufacturer: Walter Tools Facts Size: 12 Thickness: 04 Relief angle: 15° Corner radius: 0.8 mm Tolerance class: M Special features Coating/series: Tiger·tec Gold Grade: WSM35G (coated cemented carbide) Chipformer: G56 Geometry: Parallelogram 85° Suitable for: stainless steels (M), superalloys & titanium (S) FAQ What materials is this insert intended for? The ADMT120408R-G56 WSM35G insert by Walter Tools is intended for stainless steels (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), as indicated by the grade and series designation. How does the Tiger·tec Gold coating help in practice? The Tiger·tec Gold coating on the WSM35G grade improves thermal resistance and surface hardness, which extends edge life during high‑temperature cutting and reduces wear when machining challenging alloys. What is the effect of the G56 chipformer? The G56 chipformer is optimised for predictable chip breaking and evacuation, reducing the risk of built‑up edge and enabling safer, more stable milling cycles in both continuous and interrupted cuts. Which operations suit this geometry best? Parallelogram 85° geometry combined with a 15° relief angle and 0.8 mm corner radius is well suited to medium and heavy milling operations where edge strength and chip control are priorities. Is this insert appropriate for finishing cuts on stainless steel? Yes; the insert’s coating and edge geometry support improved surface quality while maintaining tool life, making it a viable option for finishing operations depending on machine and process parameters. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand presentation: Walter Tools) with headquarters in Tübingen is part of the Sandvik group and is a leading manufacturer of precision cutting tools. Protected trademarks and product names are the property of their respective owners. Mark names and registered trademarks are mentioned exclusively for explanatory purposes; there is no affiliation between our company and the mentioned brands. The offered item is an original, factory‑new product of the manufacturer.
ADMT120408R-G56 WSP45G WSP45G Wendeplatten - Walter Tools
The combination of Tiger·tec Gold coating, stable G56 chipbreaker, and a parallelogram 85° form delivers high productivity and consistent surface quality; order the ADMT120408R-G56 WSP45G milling insert directly via Metav Werkzeuge or consult the technical team for application advice. Fräswendeschneidplatte ADMT120408R-G56 WSP45G – indexable milling insert with Tiger·tec Gold coating by Walter Tools, for steel, stainless steel and heat-resistant alloys ADMT120408R-G56 WSP45G is an indexable milling insert designed for versatile milling of steels, stainless steel and heat-resistant superalloys, offering reliable chip control and edge stability Tiger·tec Gold PVD-coated carbide grade WSP45G For steel, stainless steel and heat-resistant alloys Parallelogram 85° form with 15° clearance Productivity through a robust coating and stable chip control The combination of Tiger·tec Gold PVD technology and a WSP45G coated carbide delivers measurable productivity gains in milling operations. The coating improves wear resistance and thermal stability, which results in longer tool life and fewer indexings. The G56 chipbreaker is engineered to ensure consistent chip control, reducing downtime caused by poor chip evacuation and improving cycle-time reliability. For production environments focused on efficiency, this insert supports higher process stability and more reproducible results. Precise geometry for secure engagement and surface quality The parallelogram 85° form with a 15° clearance and a 0.8 mm corner radius produces a stable cutting edge and controlled cutting forces during side and face milling. The geometry reduces vibration and spreads the cutting load across the edge, which contributes to improved surface finish and predictable wear behaviour. The insert form is especially suitable for applications requiring accurate axial and radial positioning, where the set geometry helps to maintain dimensional tolerances across repeated operations. Broad material capability explained simply This insert is rated for the ISO material groups P / M / S, meaning suitability for unalloyed and alloyed steels, stainless steel, and heat-resistant superalloys or titanium. The WSP45G grade is a tough, versatile PVD-coated carbide that copes well with the heat and adhesion tendencies typical of these materials. In practice, this means fewer tool changes across mixed-component batches and improved throughput for shops that machine a range of demanding workpiece materials. Practical advantages for workshop integration The ADMT120408R-G56 WSP45G insert integrates into common milling tool holders as an indexable insert, simplifying tool inventory and replacement procedures. Consistent manufacturing tolerances (tolerance class M) ensure repeatable seating and minimal rework during re-indexing. Where process reproducibility and predictable maintenance intervals are essential, the insert’s design helps to reduce setup variability and increase overall machine uptime. For technical guidance on integrating the Walter Tools ADMT120408R-G56 WSP45G into specific machining processes or to request a quote, contact Metav Werkzeuge for expert assistance and ordering. Technical Data SKU: ADMT120408R-G56-WSP45G-WALTER Product type: Fräswendeschneidplatte (indexable milling insert) Series: Tiger·tec Gold Grade: WSP45G Manufacturer: Walter Tools Facts Clearance angle: 15° Corner radius: 0.8 mm Insert size: 12 Thickness: 04 Tolerance class: M Special features Parallelogram 85° form Chipbreaker: G56 Material groups: P / M / S Execution: T ISO designation: ADMT120408R-G56 WSP45G Base designation without grade: ADMT120408R-G56 FAQ What workpiece materials can this insert machine effectively? The ADMT120408R-G56 WSP45G insert is suitable for machining steels, stainless steel and heat-resistant superalloys/titanium (ISO groups P / M / S), providing stable cutting performance across these materials. How does the Tiger·tec Gold coating benefit milling applications? The Tiger·tec Gold PVD coating on the ADMT120408R-G56 WSP45G improves wear resistance and thermal stability, which extends tool life and supports consistent surface quality in demanding milling cycles. What is the advantage of the parallelogram 85° form? The parallelogram 85° form offers secure seating and optimised cutting geometry for side and face milling, reducing vibration and improving reproducibility of the tool path when using the ADMT120408R-G56 WSP45G. Is the insert suitable for high-speed milling operations? The WSP45G grade and the insert geometry are designed for productive milling; recommended cutting parameters depend on the workpiece material and machine capabilities, and the ADMT120408R-G56 WSP45G performs well under appropriately adjusted high-speed conditions. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned solely for explanation. There is no affiliation between our company and the named manufacturers. The offered item is original, factory-new merchandise of the manufacturer Walter Tools.
ADMT120412R-F56 WKP35G Wendeplatten - Walter Tools
High wear resistance from the Tiger·tec Gold coating and the WKP35G grade, combined with a robust 1.2 mm corner radius and parallelogram 85° geometry, delivers stable, productive machining of steel and cast iron; order directly via Metav Werkzeuge or consult our specialists for application advice. ADMT120412R-F56 WKP35G milling indexable insert — Tiger·tec Gold for steel & cast iron (Walter Tools) The ADMT120412R-F56 WKP35G is a parallelogram 85° milling insert engineered for reliable, wear-resistant cutting in steel and cast iron applications. Tiger·tec Gold coated carbide grade WKP35G Suitable for steel and cast iron machining Parallelogram 85° cutting geometry 15° clearance angle for stable cutting Corner radius 1.2 mm for robust edges Engineered for consistent material removal and chip control The combination of the Tiger·tec Gold coating and the WKP35G carbide grade delivers enhanced resistance to abrasive wear and improved thermal stability in demanding milling operations. The integrated F56 chipbreaker is tuned to promote predictable chip formation when machining ISO groups P and K, which means more consistent cutting forces and reduced risk of unexpected tool interruptions. The parallelogram 85° geometry provides a balanced cutting position that supports stable engagement and efficient evacuation of chips, helping to maintain surface quality and process reliability over longer tool lives. Increased productivity through reproducible edge stability A 1.2 mm corner radius and a 15° clearance angle give the insert a robust cutting edge that tolerates higher cutting loads and shock conditions, translating into fewer indexings and more productive machining cycles. The tolerance class M and execution code T ensure repeatable seating and predictable performance in standard pocket clamps, which supports efficient tool management and reduced setup variability. For production environments where predictable tool life and process repeatability are valued, this geometry and grade combination contributes directly to improved machine uptime and lower overall machining costs. Clear selection and application benefits for workshop and production planning Specified as a coated carbide insert in the Tiger·tec Gold series, this item suits a wide range of general-purpose milling tasks in steel and cast iron, from light profiling to more demanding peripheral milling where stability and wear resistance are required. The insert’s design supports straightforward inventory allocation: one grade for multiple P and K applications, simplifying tool choice and replenishment. For tailored cutting data or to match the insert to a particular holder or machining strategy, technical documentation from the manufacturer and measured process feedback should be consulted to achieve optimal results. Contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored cutting data and application support for this Walter Tools Tiger·tec Gold insert Technical Data SKU: ADMT120412R-F56-WKP35G-WALTER Designation: ADMT120412R-F56 WKP35G Type: Milling indexable insert Series: Tiger·tec Gold Grade: WKP35G Chipbreaker: F56 Geometry: Parallelogram 85° Execution: T Tolerance class: M Core data Corner radius: 1.2 mm Clearance angle: 15° Insert size: 12 Thickness code: 04 Special features Material group: P / K (steel and cast iron) Suitable for: steel Suitable for: cast iron Series technology: Tiger·tec Gold (coated carbide) Manufacturer: Walter Tools FAQ Which workpiece materials is this insert designed for? The ADMT120412R-F56 WKP35G insert from Walter Tools is designed for ISO groups P and K, specifically for machining steel and cast iron. What are the main benefits of the WKP35G grade and Tiger·tec Gold series? The WKP35G grade combined with Tiger·tec Gold coating offers high abrasion resistance and thermal stability, improving tool life and maintaining edge integrity in challenging steel and cast iron milling. How does the insert geometry contribute to process stability? The parallelogram 85° geometry and 15° clearance angle provide balanced engagement and predictable chip flow, while the 1.2 mm corner radius reduces edge chipping under higher loads. For which milling tasks is this chipbreaker (F56) best suited? The F56 chipbreaker supports controlled chip formation across a variety of milling operations in P and K materials, promoting consistent cutting forces and surface finish. What should be considered when choosing this insert for production? Consider machine rigidity, clamping method, and expected cutting conditions; the ADMT120412R-F56 WKP35G is intended where robust edge stability and predictable wear behaviour are priorities. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned only for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered article is original, factory-new goods from the manufacturer Walter Tools. The Walter brand is part of the Walter AG / Walter Tools product portfolio and is referenced here solely to describe the origin and specification of the product.
ADMT120412R-F56 WKP35S Wendeplatten - Walter Tools
The combination of a WKP35S wear-resistant grade and Tiger·tec Silver coating ensures reliable performance on steel and cast iron, reducing downtime and tool change frequency; order the insert directly via Metav Werkzeuge or consult the technical team for application-specific advice. ADMT120412R-F56 WKP35S — Indexable milling insert, F56 chipbreaker, Walter Tools The ADMT120412R-F56 WKP35S is an indexable milling insert designed for productive machining of steel and cast iron, featuring a 15° relief angle and a robust parallelogram 85° form. Tiger·tec Silver coating for long tool life WKP35S grade for steel and cast iron 15° relief angle for stable cutting Parallelogram 85° form with 1.2 mm corner Durable coating for extended service life and consistent results The Tiger·tec Silver coating combined with the WKP35S substrate provides a balance of wear resistance and toughness that is engineered for the thermal and mechanical stresses typical when machining steel and cast iron. This coated carbide construction reduces abrasive and adhesive wear, which in turn extends tool life and supports reproducible component quality. The result is a measurable reduction in tool changes and improved process stability, particularly in medium- to high-volume production where predictable tool performance is essential. Geometry tuned for secure clamping and controlled chip formation With a 15° relief angle and a parallelogram 85° form, the insert delivers secure seating and effective engagement for radial and axial milling operations; the 1.2 mm corner radius increases edge strength for interrupted cuts and contributes to a consistent surface finish. The integrated F56 chipbreaker is designed to fragment and evacuate chips efficiently when machining both continuous and brittle chip formers, which helps to maintain stable cutting forces and reduces the risk of re-cutting chips in the work zone. These geometric choices translate into improved tool life and a more predictable machining cycle. Application focus and economical advantages in production Specified for groups P and K according to ISO 513, the grade is intended for unalloyed and alloyed steel as well as cast iron, making the insert a versatile option across mixed production environments. The coated cutting material is suited to standard machining feeds and speeds typical for catalogue geometries, offering a practical compromise between performance and cost-efficiency. Using this insert can lead to higher machine uptime and lower per-part tooling costs due to fewer changes and stable edge behaviour under common shop conditions. Contact Metav Werkzeuge for tailored application guidance and to secure Walter Tools ADMT120412R-F56 WKP35S inserts for reliable, productive milling Technical data SKU: ADMT120412R-F56-WKP35S-WALTER Product type: Indexable milling insert Brand: Walter Tools Series: Tiger·tec Silver Grade: WKP35S Facts Relief angle: 15° Corner radius: 1.2 mm Plate size: 12 mm Thickness: 04 Form angle: Parallelogram 85° Special features Chipbreaker: F56 Applicable materials: Steel (P), Cast iron (K) Execution: T Tolerance class: M Designation: ADMT120412R-F56 ISO designation: ADMT120412R-F56 WKP35S FAQ What materials are suitable for this insert? The ADMT120412R-F56 WKP35S insert by Walter Tools is suitable for machining steel (P) and cast iron (K) as indicated by its grade and series. What benefits does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating on the WKP35S grade improves wear resistance and thermal stability, extending service life and supporting consistent results in milling operations. How does the parallelogram 85° form affect machining? The parallelogram 85° shape provides secure seating and favourable cutting angles for effective engagement during radial and axial milling, improving stability and surface finish. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
ADMT120412R-F56 WSM35G T Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold wear resistance, the WSM35G coated-carbide grade and optimised F56 chip control for secure machining of stainless steel and heat‑resistant superalloys; order directly via Metav Werkzeuge or request tailored advice from our consultants. ADMT120412R-F56 WSM35G milling insert — Tiger·tec Gold, for stainless steel & superalloys | Walter Tools The ADMT120412R‑F56 WSM35G is a parallelogram 85° milling insert engineered for high‑temperature alloy and stainless steel operations, offering robust edge stability and consistent chip formation. Tiger·tec Gold coated carbide grade WSM35G Optimised chip control with F56 chipbreaker Parallelogram 85° form with 15° free angle Suitable for stainless steel and superalloys Longer tool life through advanced coating and grade selection The Tiger·tec Gold coating paired with the WSM35G grade is designed to resist abrasive wear and thermal load, which translates into extended tool life and fewer index changes during production. Coated carbide ensures heat resistance and edge stability when machining demanding materials such as stainless steel and nickel‑based alloys; this reduces the frequency of interruptions and supports steady cycle times. Less wear means lower tool consumption and improved cost efficiency over extended production runs. Predictable chip flow and fewer process interruptions A dedicated F56 chipbreaker and the parallelogram 85° insert form deliver controlled chip detachment and predictable evacuation, which is essential for continuous milling of heat‑resistant alloys. The geometry, combined with a 15° free angle and a 1.2 mm corner radius, provides a balance between shear strength and surface integrity. Process stability is enhanced, resulting in reduced built‑up edge formation and more consistent surface finishes, thereby supporting higher machine utilisation and reliable output quality. Versatility across roughing and finishing tasks With tolerance class M and the compact size 12 format, the insert is adaptable to a range of machining strategies from aggressive material removal to fine finishing passes depending on toolholder and cutter configuration. The thickness 04 and the insert’s design allow secure clamping and repeatable positioning, so machining programmes remain stable and reproducible. The result is a flexible solution that supports mixed production environments where different grades and materials must be processed with consistent results. Practical benefits for workshop workflows As an indexable milling plate from Walter Tools, this insert simplifies tool management: quick indexing reduces downtime and the standard form factor integrates seamlessly into existing cutter systems. The combination of a stable cutting edge and effective chip control improves operator confidence and contributes to predictable planning of tool change intervals. For complex components or serial production in aerospace, energy or medical sectors, the insert supports reproducible quality and process security. Contact Metav Werkzeuge for application advice and to secure a supply of Walter Tools ADMT120412R‑F56 WSM35G inserts for challenging stainless steel and superalloy machining Technical Data SKU: ADMT120412R-F56-WSM35G-WALTER Article designation: ADMT120412R-F56 WSM35G Product type: Fräswendeschneidplatte / milling insert Manufacturer: Walter Tools Facts Free angle: 15° Corner radius: 1.2 Insert size: 12 Thickness: 04 Tolerance class: M Special features Series: Tiger·tec Gold Grade: WSM35G Chipbreaker: F56 Plate form: Parallelogram 85° Material application: S / M Execution: T FAQ What materials is this insert best suited for? The ADMT120412R‑F56 WSM35G insert is intended for stainless steel and heat‑resistant superalloys (S / M), offering enhanced edge life and thermal stability for these groups. How does the F56 chipbreaker improve machining? The F56 chipbreaker on the ADMT120412R‑F56 promotes controlled chip formation and evacuation, which helps to maintain stable cutting conditions and reduces the risk of built‑up edge when machining difficult materials. Can the insert be used for both roughing and finishing? Yes, the combination of the parallelogram 85° form, tolerance class M and the insert geometry allows flexible use from heavier roughing to finishing passes when matched with the appropriate cutter and process parameters. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation and identification purposes; no affiliation with Metav Werkzeuge is implied. The offered article is an original, factory‑new product of the manufacturer.
ADMT120412R-F56 WSP45G WSP45G Wendeplatten - Walter Tools
Reliable milling performance with the Tiger‑tec Gold coating and the versatile WSP45G grade delivers stable chip formation and long tool life, especially in demanding steel and stainless steel applications. The parallelogram 85° geometry combined with a 15° clearance and 1.2 mm corner radius provides secure clamping and improved edge strength. Order the ADMT120412R-F56 WSP45G directly via Metav Werkzeuge or consult our specialists for application advice. ADMT120412R-F56 WSP45G milling insert, Parallelogram 85°, Tiger‑tec Gold (Walter Tools) The ADMT120412R-F56 WSP45G is a versatile milling insert designed for finishing and general milling of steel, stainless steel and heat‑resistant alloys Tiger‑tec Gold coating for extended tool life Suitable for Steel, Stainless and Superalloys Parallelogram 85° shape for secure clamping 15° clearance angle for stable cutting 1.2 mm corner radius for improved edge strength Durable coating and material adaptability for reliable production The combination of the Tiger‑tec Gold coating and the WSP45G grade creates a PVD‑coated cutting surface engineered for durability and predictable wear. This specification is tailored to handle the thermal loads and chip behaviour typical of machining steel and stainless steel, while also offering resilience for tougher superalloys and titanium‑based materials. The result is consistent tool life and fewer unexpected tool changes, supporting a smooth production flow and reduced downtime. Geometry that improves stability and workpiece quality The parallelogram 85° insert form gives a secure seat in compatible toolholders and optimises the clamping force distribution for milling operations. A 15° clearance reduces rubbing at the flank, while the 1.2 mm corner radius increases edge strength and helps achieve a more uniform surface finish. The integrated chipbreaker F56 assists in controlled chip formation, lowering the risk of built‑up edge and improving repeatable dimensional results on the workpiece. Practical benefits for productivity and process security Designed as a general‑purpose milling solution, this insert supports a wide range of applications from finishing passes to medium‑duty face milling. The versatile grade minimises the need for multiple insert types across different materials, which simplifies inventory and contributes to cost efficiency in high‑mix production environments. For process planning, the insert’s balanced geometry and coating can help maintain cycle times and improve overall process stability when used in appropriately rated holders and cutting parameters. For additional machining data or application recommendations, Metav Werkzeuge provides tailored consultation and cutting‑tool expertise. Contact Metav Werkzeuge for tailored application support and to request ordering details for the Walter Tools ADMT120412R-F56 WSP45G milling insert Technical data SKU: ADMT120412R-F56-WSP45G-WALTER Article designation: ADMT120412R-F56 WSP45G Product type: Fräswendeschneidplatte / milling insert Series: Tiger‑tec Gold Grade: WSP45G Manufacturer: Walter Tools Facts Insert size: 12 Corner radius: 1.2 mm Clearance angle: 15° Thickness code: 04 Tolerance class: M Special features Coating: Tiger‑tec Gold (PVD) Chipbreaker: F56 Shape: Parallelogram 85° Grade material: P / M / S (Steel / Stainless steel / Superalloys) Execution: T Designation without grade: ADMT120412R-F56 FAQ Is this insert suitable for stainless steel machining? Yes. The ADMT120412R-F56 WSP45G is specified for stainless steel applications and its WSP45G grade is designed to promote secure chip formation and edge stability when machining stainless materials. What does the chipbreaker F56 do? The chipbreaker F56 on the ADMT120412R-F56 WSP45G controls chip shape and evacuation, which helps reduce chip entanglement and supports consistent surface quality during milling. Can this insert be used on heat‑resistant superalloys and titanium? Yes. The WSP45G grade covers the S material group and offers enhanced heat resistance and edge stability for demanding alloys and titanium‑based materials. Which geometric features improve clamping and surface finish? The parallelogram 85° shape combined with a 15° clearance and 1.2 mm corner radius enhances clamping security, reduces vibration and contributes to improved surface finishes in routine milling operations. Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. It is an original, factory‑new item of the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
ADMT120416L-F56 WKP35G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating, the WKP35G grade and a precise parallelogram 85° geometry to achieve consistent chip control and long tool life when machining Stahl and Gusseisen. Order the ADMT120416L-F56 WKP35G directly via Metav Werkzeuge or consult our specialists for application-specific guidance. ADMT120416L-F56 WKP35G milling indexable insert — Parallelogramm 85°, 15° relief (Walter Tools) The ADMT120416L-F56 WKP35G is a parallelogram 85° milling indexable insert designed for productive machining of Stahl (P) and Gusseisen (K), combining a Tiger·tec Gold coated substrate with a tailored chipbreaker for reliable performance. Tiger·tec Gold coating for abrasion resistance Optimised chip control with F56 chipbreaker Parallelogramm 85° geometry for versatile milling 15° relief angle and 1.6 mm corner radius Stable cutting performance thanks to modern coating technology The combination of the Tiger·tec Gold coating and the WKP35G grade yields a coating system optimised for abrasive wear resistance and thermal stability, which translates into longer service life in mixed production environments. The coated cemented carbide construction, described in the series information, is specifically tailored for typical heat development and chip behaviour when machining Stahl and Gusseisen. This reduces flank wear and maintains dimensional accuracy over longer tool life, therefore increasing productivity per insert installed. Better chip control and surface finish through geometry The parallelogram 85° form and the integrated F56 chipbreaker improve chip evacuation and reduce built-up edge formation in interrupted and continuous cuts. With a 15° relief angle and a 1.6 mm corner radius, this geometry balances edge strength and cutting sharpness, enabling stable performance on a wide range of workpiece geometries. For operations that require repeatable surface quality, the geometry minimises vibration and supports consistent cutting conditions across different batch sizes. Application advantages: efficient machining of Stahl and Gusseisen Selected for use on Stahl (P) and Gusseisen (K) according to ISO 513 groupings, the insert addresses the most common industrial machining tasks where a combination of wear resistance and chip control is essential. The WKP35G grade is a coated carbide variant that performs well under the typical thermal and mechanical loads encountered in these materials. Where throughput and reproducible results matter, this insert supports stable cycle times and predictable tool-change intervals, contributing to lower unit costs and improved shop-floor efficiency. Contact Metav Werkzeuge for application advice on using the Tiger·tec Gold WKP35G insert in specific machining scenarios or to request further technical documentation via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: ADMT120416L-F56-WKP35G-WALTER Designation: ADMT120416L-F56 WKP35G Type: Fräswendeschneidplatte Series: Tiger·tec Gold Grade: WKP35G Manufacturer: Walter Tools Facts Corner radius: 1.6 mm Relief angle: 15° Insert size: 12 mm Thickness: 4 mm Tolerance class: M Special features Geometry: Parallelogramm 85° Chipbreaker: F56 Material applicability: Stahl (P) and Gusseisen (K) Execution: T Coating: Tiger·tec Gold (coated cemented carbide) FAQ What materials is this insert suitable for? The ADMT120416L-F56 WKP35G is intended for machining Stahl (P) and Gusseisen (K) as defined by ISO 513 and is optimised accordingly. How does the Tiger·tec Gold coating affect tool life? The Tiger·tec Gold coating on the WKP35G grade improves resistance to abrasive wear and thermal loading, which extends the useful life of the insert in standard production conditions. What advantage does the parallelogram 85° shape provide? The parallelogram 85° geometry allows flexible milling strategies and supports efficient chip flow with the specified F56 chipbreaker, enhancing process stability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ADMT120416L-F56 WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold PVD technology, stable chip control and precise insert geometry for reliable milling results and reduced downtime; order directly via Metav Werkzeuge or contact the consultants for application support and tailored recommendations. ADMT120416L-F56 WSP45G milling insert — Tiger·tec Gold PVD, 15° relief (Walter Tools) The ADMT120416L-F56 WSP45G is a PVD-coated milling insert designed for versatile milling of Stahl, rostfreier Stahl and heat‑resistant alloys in demanding production environments. Tiger·tec Gold PVD coating *Suitable for Stahl, rostfreier Stahl, and superalloys *Parallelogram 85° insert geometry *15° relief and 1.6 mm corner radius Stable chip formation for predictable cycle times The combination of the Tiger·tec Gold coating and the F56 chipbreaker delivers consistently controlled chip formation across a wide range of applications. The engineered chip control reduces interruptions and the need for manual chip handling, which helps to maintain steady cycle times and minimises rework. As a result, the production process benefits from improved throughput and fewer process deviations. Durable cutting edges for longer tool life The insert grade WSP45G is a tough, PVD‑coated carbide designed to withstand the thermal and mechanical loads typical of milling operations in Stahl, rostfreier Stahl and high‑temperature alloys. This composition supports a stable cutting edge, reducing flank wear and extending time between indexings or re‑grinds. The outcome is a lower effective tooling cost per component and enhanced process reliability. Precision geometry for flexible milling strategies The parallelogram 85° form combined with a 15° relief and 1.6 mm corner radius provides a balance between strength and accessibility. The insert’s size (12 mm) and thickness code (04) enable both robust roughing and fine finishing passes when matched with appropriate cutting parameters. The geometry promotes a favourable force distribution on the cutter body, supporting stable toolpaths and predictable surface quality. Application scope and process recommendations This indexable insert is intended for general milling tasks across the P / M / S material groups, covering unalloyed and alloyed Stahl, rostfreier Stahl, plus heat‑resistant superalloys and titanium grades. The Tiger·tec Gold layer enhances wear resistance and aids in reliable chip evacuation. For optimal performance, select feeds and speeds that correspond to the workpiece material and machine rigidity; for specialised setups or sample calculations, Metav Werkzeuge’s technical team can provide targeted advice and parameter sheets. Contact Metav Werkzeuge for tailored application advice, supply options and to discuss integration of Walter Tools ADMT120416L‑F56 WSP45G inserts into existing machining processes Technical Data Article number: ADMT120416L-F56-WSP45G-WALTER Designation: ADMT120416L-F56 WSP45G Series: Tiger-tec Gold Manufacturer: Walter Tools Core dimensions Size: 12 mm Thickness code: 04 Relief angle: 15° Corner radius: 1.6 mm Geometry angle: 85° Materials & special features Grade: WSP45G Coating: Tiger·tec Gold (PVD) Chipbreaker: F56 Material range: P / M / S Execution: T Tolerance class: M FAQ What materials can this insert machine? The ADMT120416L‑F56 WSP45G is specified for the P, M and S groups and is suitable for machining Stahl, rostfreier Stahl and heat‑resistant superalloys including titanium. How does the Tiger·tec Gold coating affect performance? The Tiger·tec Gold PVD coating improves wear resistance and heat tolerance, enabling the WSP45G grade to maintain a stable cutting edge under typical milling loads and extending the tool‑life in serial production. Which chipbreaker is fitted and what is its benefit? The insert features an F56 chipbreaker, which is designed to produce predictable chip shapes and to facilitate efficient evacuation, reducing the risk of recutting and machine downtime. What geometric features support finishing operations? The parallelogram 85° form with a 15° relief and 1.6 mm corner radius provides a compromise between edge strength and surface finish capability, enabling controlled finishing passes when paired with the correct cutting data. Is this insert suited for high‑productivity milling? Yes. The combination of the WSP45G grade and Tiger·tec Gold coating delivers process security and reliable edge stability that support higher material removal rates when machine rigidity and cooling strategy are appropriate. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
ADMT120416R-F56 WKP35G T Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold wear resistance and robust geometry for consistent cutting performance and longer tool life; the design supports reliable chip control in demanding steel and cast-iron operations. Order the ADMT120416R-F56 WKP35G milling insert directly via Metav Werkzeuge or ask our consultants if needed. ADMT120416R-F56 WKP35G milling insert — Tiger‑tec Gold, chipbreaker F56 — Walter Tools ADMT120416R-F56 WKP35G is a precision indexable milling insert optimised for productive machining of steel and cast iron in demanding industrial applications Tiger‑tec Gold coating for enhanced wear resistance Suitable for steel (P) and cast iron (K) Parallelogram 85° form, 15° rake angle Corner radius 1.6 mm for stable cutting Increase process reliability with coated Tiger‑tec Gold technology The Tiger‑tec Gold coating combines a durable layered finish with a tailored substrate to reduce flank and crater wear, which improves consistency in serial production. As a result, cycle times remain steady and tool-change intervals are extended, supporting higher machine uptime and predictable outputs. The WKP35G grade is formulated specifically for the thermal and abrasive demands encountered when machining steel and cast iron, delivering stable cutting and dependable flank-life behaviour under a range of cutting parameters. Geometry and chip control designed for predictable productivity A parallelogram 85° form with a chipbreaker F56 and a corner radius 1.6 mm gives this insert a balanced combination of edge strength and chip segmentation. The geometry promotes controlled chip formation and evacuation, reducing the risk of built-up edge and improving surface finish consistency. The insert’s 15° rake angle supports efficient cutting forces and contributes to lower power consumption during heavy cuts, which translates into measurable gains in productivity on batch and continuous operations. Application versatility and integration into existing tool systems Marked as suitable for the ISO material groups P and K, this indexable insert performs across a broad material spectrum typical in general engineering and automotive production. The grade and series choice minimises sorting complexity while enabling process engineers to select a single insert for multiple workpiece types. Compatibility with standard toolholders and straightforward indexing means rapid replacement and minimal setup overhead, helping to keep spindle time productive and tool logistics simple in the workshop. Contact Metav Werkzeuge for application advice on the Walter Tools Tiger‑tec Gold inserts and fast, reliable availability. Technical Data SKU: ADMT120416R-F56-WKP35G-WALTER Item designation: ADMT120416R-F56 WKP35G Brand: Walter Tools Facts Corner radius: 1.6 mm Rake/free angle: 15° Form/shape: Parallelogram 85° Size: 12 Thickness: 04 Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WKP35G (coated carbide) Chipbreaker: F56 Material suitability: steel (P), cast iron (K) Substrate/grade notation: P / K Execution: T FAQ What materials is this insert suitable for? The ADMT120416R-F56 WKP35G insert is specified for ISO groups P and K, meaning it is suitable for machining steel and cast iron with optimised wear behaviour for these materials. What advantages does the Tiger‑tec Gold series provide? The Tiger‑tec Gold series offers a coated carbide combination designed to improve wear resistance and maintain cutting-edge stability, which helps to extend tool life and secure consistent machining results. How does the insert geometry affect machining results? The parallelogram 85° form with chipbreaker F56 and a corner radius 1.6 mm delivers predictable chip control and edge strength, supporting better surface finish and fewer interruptions for chip-related issues. Is this insert compatible with standard milling holders? Yes, the insert’s form and designation follow common indexable milling standards; it can be integrated into holders that accept the ADMT120416R-F56 family, enabling straightforward indexing and replacement. Which grade designation should be chosen for mixed production of steel and cast iron? The WKP35G grade balances the demands of both steel and cast iron, making it a practical choice for mixed-production environments where a single insert type reduces tool inventory complexity. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners and are mentioned solely for clarification. There is no affiliation between Metav Werkzeuge and the named brands. The offered article is original, factory-new merchandise of the manufacturer.
ADMT120416R-F56 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of proven Tiger‑tec Silver performance, stable chip control and robust edge strength to keep milling cycles productive and predictable; order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. ADMT120416R-F56 WKP35S indexable milling insert, Tiger‑tec Silver, for Steel and Cast iron | Walter Tools ADMT120416R-F56 WKP35S is a parallelogram milling insert designed for versatile face and slot milling in steels and cast irons Tiger‑tec Silver coating, WKP35S grade Suitable for Steel (P) and Cast iron (K) Parallelogram 85° form for versatile milling Corner radius 1.6 mm for reliable edge strength High-performance coated grade for consistent productivity The ADMT120416R-F56 WKP35S insert uses the Tiger‑tec Silver technology to combine a wear-resistant coated carbide substrate with surface engineering that stabilises flank wear and extends tool life. The WKP35S grade is optimised for cyclic loads typical of steel and cast-iron machining, which translates directly into fewer indexings and reduced tooling cost per part. By controlling flank wear and promoting steady cutting conditions, the insert supports higher metal removal rates while helping to maintain repeatable component dimensions and consistent cycle times. Geometry that improves chip flow and surface quality The parallelogram shape with an 85° form and a 15° clearance angle provides a favourable cutting geometry for a wide range of finishing and semi-finishing operations. The integrated chipbreaker F56 promotes orderly chip formation and evacuation; this reduces re-cutting of swarf and helps achieve a stable surface finish. For customers less familiar with industry coding: the letters P and K follow ISO 513 and indicate suitability for Steel (P) and Cast iron (K) respectively. The combination of geometry and chip control contributes to reduced vibration and improved tool life, which benefits throughput and downstream processes such as heat treatment or assembly. Robust design and process security for workshop integration With a corner radius 1.6 mm and a thickness of 4 mm in a 12 mm insert format, this grade offers a balance between edge strength and cutting versatility. The tolerance class M ensures repeatable seating and positioning in standard milling cutters, simplifying tool setup and changeover. The insert's designation and chipbreaker match common clamping systems, making retrofit into existing toolheads straightforward. Walter Tools' production quality and the Tiger‑tec Silver series deliver consistent performance across batches, supporting predictable maintenance intervals and easier process planning for production environments. For application-specific advice on the Tiger‑tec Silver WKP35S range or to assess suitability for particular machining tasks, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav Werkzeuge will provide tailored recommendations and cutting data. Technical data Article number: ADMT120416R-F56-WKP35S-WALTER Label: Fräswendeschneidplatte ADMT120416R-F56 WKP35S Walter Tools Manufacturer: Walter Tools Facts Free cutting angle: 15° Corner radius: 1.6 mm Insert size: 12 mm Thickness: 4 mm Form angle: Parallelogram 85° Tolerance class: M Special features Coating/grade: Tiger‑tec Silver, WKP35S Chipbreaker: F56 Material compatibility: Steel (P) and Cast iron (K) Designation: ADMT120416R-F56 WKP35S Execution: T FAQ Which materials is this insert suitable for? The ADMT120416R-F56 WKP35S insert is designed for Steel (P) and Cast iron (K) applications, following ISO 513 classifications; the Tiger‑tec Silver grade balances toughness and wear resistance for these materials. What does the WKP35S grade offer compared with other grades? WKP35S is a Walter Tools coated carbide grade within the Tiger‑tec Silver family, offering enhanced wear resistance and thermal stability suited to cyclic loads in steel and cast-iron machining. How does the chipbreaker F56 affect machining? The F56 chipbreaker promotes orderly chip formation and evacuation, improving chip control and reducing the risk of re-cutting swarf, which supports a better surface finish and more stable cutting forces. Why is the parallelogram 85° form beneficial? The Parallelogram 85° geometry provides a versatile cutting edge orientation that balances radial and axial force components, enabling flexible engagement strategies for both slotting and face milling with controlled tool deflection. What is the significance of the corner radius and tolerance class? A corner radius of 1.6 mm increases edge robustness for interrupted cuts, while tolerance class M ensures consistent seating and repeatable positioning in compatible milling cutters; together they support process reliability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Trademarks and product names mentioned are the property of their respective owners. Brand names and protected trademarks are cited solely for explanation. No connection between our company and the trademark owners is implied. The offered item is an original, factory-new product of the manufacturer Walter Tools.
ADMT120416R-F56 WSM35G WSM35G Wendeplatten - Walter Tools
Enhanced productivity and consistent edge life result from the Tiger·tec Gold coating combined with the WSM35G grade, optimised for stainless steels and heat‑resistant alloys. The ADMT120416R‑F56 insert offers controlled chip formation via the F56 breaker and robust edge security with a 1.6 mm corner radius — order directly via Metav Werkzeuge or consult our specialists for application support. ADMT120416R-F56 WSM35G milling insert by Walter Tools — Tiger·tec Gold, F56 chipbreaker The ADMT120416R-F56 WSM35G is a parallelogram 85° milling insert designed for reliable machining of stainless steels and heat‑resistant superalloys. Tiger·tec Gold coating for high wear resistance Optimised F56 chipbreaker for reliable chip control Suitable for stainless steels and superalloys 1.6 mm corner radius for improved edge strength Higher throughput with a hard‑wearing grade and coating The combination of the WSM35G grade and Tiger·tec Gold coating delivers measurable improvements in tool life and process stability when working with demanding materials. Designed for materials that tend to work‑harden or generate high temperatures, this coated cemented‑carbide grade supports stable chip formation and reduced flank wear. The result is fewer tool changes, less unplanned downtime and a more predictable production rhythm — all of which contribute to lower unit costs and higher overall productivity. Consistent surface quality and secure cutting edges The insert’s parallelogram 85° geometry, combined with a 15° free angle and a 1.6 mm corner radius, provides a good mix of accessibility and edge robustness. The F56 chipbreaker is optimised to produce controllable chips on stainless steels and heat‑resistant alloys, reducing the risk of built‑up edge and improving surface finish. With this geometry, the insert maintains a stable cutting edge under thermal stress, which helps to achieve reproducible component quality across series production. Predictable integration into production environments Tolerance class M and the standardised designation simplify tool planning and tool‑holder selection. The insert’s specification supports process planners who prioritise repeatability: consistent tool life, known wear behaviour and easy replacement. The robust nature of the grade and coating also supports tougher operating windows, allowing for optimised cutting parameters and fewer process iterations during setup. This makes the insert particularly suitable for shops focused on efficiency and reliable throughput. Application focus and handling recommendations Specifically engineered for machining stainless steels (ISO group M) and heat‑resistant superalloys and titanium (ISO group S), the insert is well suited to components that demand thermal stability and clean chip evacuation. When integrating the insert into an existing process, select the appropriate feed and depth of cut for temperature control and consider coolant strategy for high alloy materials. The insert’s geometry and chipbreaker ease handling in both semi‑roughing and finishing passes, providing flexibility across several production stages. Contact Metav Werkzeuge for availability and tailored cutting recommendations for the Walter Tools ADMT120416R‑F56 WSM35G milling insert Technical data SKU: ADMT120416R-F56-WSM35G-WALTER Article designation: ADMT120416R-F56 WSM35G Manufacturer: Walter Tools Product type: Milling insert (indexable) Series: Tiger‑tec Gold Grade: WSM35G Core specifications Free angle: 15° Corner radius: 1.6 mm Insert size: 12 Thickness code: 04 Parallelogram angle: 85° Tolerance class: M Chipbreaker: F56 Features and applications Coating technology: Tiger·tec Gold Grade: WSM35G (coated cemented carbide) Suitable materials: stainless steels (M), superalloys and titanium (S) Geometry: Parallelogram 85° Execution code: T Material code: S / M FAQ What materials is this insert intended for? The ADMT120416R‑F56 WSM35G insert is intended for stainless steels (ISO group M) and heat‑resistant superalloys and titanium (ISO group S), using the Tiger·tec Gold coating to maintain edge stability. How does the F56 chipbreaker improve machining? The F56 chipbreaker on this Walter Tools milling insert promotes controlled chip formation and evacuation, reducing the risk of built‑up edge and aiding consistent surface quality. What does the 1.6 mm corner radius mean in practice? A 1.6 mm corner radius provides enhanced edge strength and resistance to chipping, which is beneficial for semi‑finishing and finishing passes where edge robustness supports repeatable results. Is this insert compatible with standard holders? The ADMT120416R‑F56 WSM35G follows standard insert dimensions and tolerance class M, enabling straightforward integration with compatible tool holders designed for parallelogram 85° inserts. Which series and coating technology does the insert use? This insert belongs to the Tiger·tec Gold series and uses the WSM35G coated grade, optimised for demanding, heat‑generating workpiece materials. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only and do not imply any affiliation between our company and the listed manufacturers. The offered item is an original, factory‑new product from the manufacturer.
ADMT120416R-F56 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the robust WSP45G grade for extended tool life and consistent chip control; the insert’s 15° relief and 1.6 mm corner radius support secure cutting in demanding milling operations. Order this insert directly via Metav Werkzeuge or consult our technical team for application-specific recommendations. ADMT120416R-F56 WSP45G — Milling indexable insert (Tiger‑tec Gold, 15° relief) by Walter Tools The ADMT120416R-F56 WSP45G is a parallelogram milling indexable insert designed for versatile face and shoulder milling across steel, stainless steel and heat‑resistant alloys. Tiger‑tec Gold PVD‑coated grade WSP45G Suitable for steel, stainless and superalloys 15° relief angle for secure cutting Parallelogram 85° insert with 1.6 mm radius High‑performance coating for longer tool life The combination of Tiger‑tec Gold technology and the WSP45G grade provides a PVD‑coated cutting edge engineered for extended life and stable performance. The coating reduces flank wear and supports consistent chip control, which lowers machining downtime and improves overall process reliability. For production environments where tool longevity and repeatable results matter, this coating‑substrate pairing reduces the frequency of index changes and contributes directly to improved throughput. Edge geometry that ensures repeatable, secure cuts The insert’s 1.6 mm corner radius with a 15° relief angle and Parallelogram 85° shape is designed to deliver stable engagement and predictable cutting forces. A larger corner radius increases edge strength for finish and semi‑roughing passes, while the relief angle promotes safer entry and exit during interrupted cuts. These characteristics combine to reduce vibration and improve surface integrity, making the insert especially suitable where dimensional repeatability and edge robustness are required. Broad material range explained for confident selection Marked as P / M / S, the insert is suitable for machining steel, stainless steel and superalloys/titanium in accordance with ISO material groupings. Steel applications typically demand heat‑resistant and good‑chip‑forming grades; stainless steels require toughness and anti‑built‑up‑edge behaviour; superalloys and titanium need thermal stability and a strong cutting edge. The ADMT120416R‑F56 WSP45G addresses these demands by combining a resilient substrate with a modern PVD coating to balance wear resistance and edge stability. Productivity features and practical benefits on the shop floor The integrated F56 chipbreaker and the insert dimensions (size 12, thickness 04) enable controlled chip formation and reliable evacuation during milling. A tolerance class of M supports consistent seating and minimal runout when paired with correctly matched toolholders, reducing setup variability. Together these features translate into fewer tool changes, predictable tool life and efficient machining cycles — advantages that deliver measurable gains in downstream operations and production planning. For productive and reliable milling with Walter Tools Tiger‑tec Gold technology, choose the ADMT120416R‑F56 WSP45G; contact Metav Werkzeuge for precise application advice or to secure supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: ADMT120416R-F56-WSP45G-WALTER Designation: ADMT120416R-F56 WSP45G Type: Milling indexable insert (Fräswendeschneidplatte) Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 1.6 mm Insert size: 12 Thickness: 04 Tolerance class: M Insert form angle: Parallelogram 85° Special features Grade: WSP45G Series: Tiger‑tec Gold Chipbreaker: F56 Applicable materials: P / M / S (steel, stainless steel, superalloys/titanium) Execution: T FAQ What materials can this insert machine effectively? The ADMT120416R‑F56 WSP45G is specified for P / M / S materials, meaning it is suitable for steel, stainless steel and superalloys/titanium, offering a versatile solution across these groups. How does the Tiger‑tec Gold coating benefit milling operations? Tiger‑tec Gold on the ADMT120416R‑F56 WSP45G enhances wear resistance and thermal stability, resulting in longer tool life and more consistent chip control in continuous and interrupted milling. What is the purpose of the F56 chipbreaker? The F56 chipbreaker on the insert promotes controlled chip formation and evacuation, reducing the risk of recutting chips and improving surface finish during face and shoulder milling. Is the insert suitable for interrupted cuts and roughing? Yes — the combination of a 1.6 mm corner radius, robust grade and 15° relief makes the insert suitable for interrupted cuts and mixed roughing/finishing operations where edge strength is critical. What does the tolerance class M indicate for workshop use? Tolerance class M ensures consistent insert dimensions for precise seating in toolholders, supporting reliable runout and repeatable machining without frequent adjustments. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original, factory‑new goods of the manufacturer.
ADMT120420R-F56 WKP35G Wendeplatten - Walter Tools
Take advantage of a Tiger·tec Gold-based grade and a precision F56 chipbreaker to achieve longer tool life and stable chip control in demanding milling operations; order directly via Metav Werkzeuge or request application advice from our consultants. ADMT120420R-F56 WKP35G indexable milling insert — Tiger·tec Gold, 15° clearance (Walter Tools) ADMT120420R-F56 WKP35G is an indexable milling insert designed for high-productivity machining of steel and cast iron, offering a coated-carbide grade and geometry optimised for reliable chip control. Tiger·tec Gold coated for long tool life Optimised chip control with F56 chipbreaker Suitable for steel and cast iron (ISO P/K) Parallelogram 85° geometry, 15° clearance Higher productivity through advanced coating and grade The Tiger·tec Gold coating combined with the WKP35G grade provides a balance of wear resistance and toughness that favours extended cutting edges in mixed-production environments. As a coated carbide solution, the insert is formulated to cope with the heat and abrasion typical when machining steel and cast iron, which are classified under ISO groups P and K respectively. This combination reduces tool changes and supports higher material removal rates, translating into measurable production gains without sacrificing component quality. Consistent chip formation and surface quality The chipbreaker F56 is tailored to produce short, controlled chips when cutting both steels and cast irons, lowering the risk of built-up edge and improving surface finish. The parallelogram 85° insert form and the 15° clearance reduce flank contact and help maintain stable cutting conditions, while the 2 mm corner radius adds robustness at the cutting edge. Together these features decrease vibration and stabilise the cutting process, which supports repeatable dimensional accuracy and a better finish on machined components. Straightforward integration into milling systems Marked as ADMT120420R-F56, the insert has a nominal size of 12 mm and a plate thickness corresponding to the 04 series, with tolerance class M for consistent seating. The execution code T and the series affiliation to Tiger-tec Gold simplify tool selection for standard milling toolholders that accept parallelogram inserts. The grade’s focus on ISO P/K makes it a versatile choice for production lines that handle a mix of unalloyed, alloyed steels and a range of cast-iron grades, enabling process planners to standardise operations and reduce tooling variants. For application-specific recommendations or to confirm stock and delivery options for the ADMT120420R-F56 WKP35G indexable milling insert, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt, expert assistance Technical data SKU: ADMT120420R-F56-WKP35G-WALTER Article designation: ADMT120420R-F56 WKP35G Product type: Indexable milling insert Manufacturer: Walter Tools Core data Clearance angle: 15° Corner radius: 2 mm Shape: Parallelogram 85° Insert size: 12 mm Thickness: 4 mm Tolerance class: M Chipbreaker: F56 Special features Coating: Tiger·tec Gold Grade: WKP35G (coated carbide) Material suitability: Steel (ISO P), Cast iron (ISO K) Series: Tiger-tec Gold Execution: T Material of insert: P / K FAQ What materials is this insert designed to machine? The ADMT120420R-F56 WKP35G indexable milling insert from Walter Tools is designed primarily for steel (ISO P) and cast iron (ISO K) applications. What benefit does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the WKP35G grade enhances wear resistance and thermal stability, extending cutting-edge life and enabling higher cutting speeds under demanding conditions. How does the F56 chipbreaker affect performance? The chipbreaker F56 produces short, controlled chips for improved chip evacuation and reduced risk of built-up edge, which contributes to more consistent surface quality and easier swarf handling. Why is the parallelogram 85° geometry advantageous? The parallelogram 85° form reduces radial cutting forces and enables favourable approach angles for milling, improving tool-holder stability and repeatability during interrupted cuts. How should the designation ADMT120420R-F56 be interpreted? The designation ADMT120420R-F56 indicates the insert geometry and chipbreaker version; combined with the WKP35G grade it identifies this specific Walter Tools solution for standard milling toolholders. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ADMT120420R-F56 WKP35S Wendeplatten - Walter Tools
High-performance Tiger‑tec Silver coating together with the WKP35S grade ensures stable chip formation and extended tool life for steel and cast iron machining; ideal where productivity and repeatable results are required. Order directly via Metav Werkzeuge or consult our specialists for application advice. ADMT120420R-F56 WKP35S indexable milling insert (Tiger‑tec Silver) — Walter Tools ADMT120420R-F56 WKP35S is an indexable milling insert designed for productive machining of steel and cast iron, combining robust cutting performance with consistent chip control Tiger‑tec Silver coating for improved wear resistance Designed for steel and cast iron machining 15° clearance, corner radius 2 Parallelogram 85° form for stable cutting Consistent productivity thanks to a modern coating and grade The combination of the Tiger‑tec Silver coating and the WKP35S grade provides high resistance to abrasive wear and stable chip control, targeted specifically at the thermal and mechanical conditions encountered when machining steel and cast iron. This coated carbide formulation reduces flank wear and supports longer tool life, which translates into fewer insert changes and increased uptime. The design focuses on repeatable results under continuous production loads, offering a reliable baseline for process planning and cycle-time optimisation. Geometry that stabilises cuts and improves surface quality A parallelogram 85° plate form with 15° clearance and a corner radius 2 delivers a balance between edge strength and cutting stability. The F56 chipbreaker is tuned for controlled chip segmentation and evacuation during interrupted and continuous cuts, reducing the risk of chatter and improving surface finish. Tolerance class M and the specified plate dimensions aid in predictable seating and indexing, which supports fast insert changes and consistent positioning in tool holders — a practical advantage in high-throughput environments. Integrating the insert into process chains for reliable results The insert's specification — including series designation Tiger‑tec Silver, grade WKP35S, and its suitability for ISO groups P and K — simplifies tooling decisions when matching cutting data to workpiece material. Its execution code T and plate characteristics make it suitable for a wide range of milling operations where stability and tool life are priorities. For production teams seeking lower variability in their machining results, this insert supports standardisation of tool inventories and facilitates predictable maintenance cycles without compromising productivity. Contact Metav Werkzeuge for tailored application guidance on Walter Tools inserts and to confirm suitability for specific machining tasks: info@metav-werkzeuge.com, +49 2822 7131930 Technical data SKU: ADMT120420R-F56-WKP35S-WALTER Article: ADMT120420R-F56 WKP35S Manufacturer: Walter Tools Product type: Indexable milling insert Series: Tiger-tec Silver Core dimensions / performance Clearance angle: 15° Corner radius: 2 Plate form: Parallelogram 85° Plate size: 12 Plate thickness: 04 Tolerance class: M Chipbreaker: F56 Materials / special features Grade: WKP35S (coated carbide) Material suitability: P (steel), K (cast iron) Execution: T Series enrichment: Tiger-tec Silver FAQ Which materials is this insert intended for? The ADMT120420R-F56 WKP35S insert is specified for machining steel (ISO group P) and cast iron (ISO group K) according to the supplied material suitability information. What benefits does the Tiger‑tec Silver coating bring? The Tiger‑tec Silver coating on the WKP35S grade increases wear resistance and supports stable chip control, which helps maintain edge life and consistent part quality during batch production. How does the plate geometry affect machining stability? The parallelogram 85° form combined with 15° clearance and corner radius 2 enhances cutting stability and reduces vibration, contributing to improved surface finish and reduced risk of tool or part damage. Is the F56 chipbreaker suitable for interrupted cuts? The F56 chipbreaker is designed to control chip formation in both continuous and interrupted milling, promoting predictable chip flow and safer machining of abrasive cast iron and tougher steels. Can the ADMT120420R-F56 WKP35S be used for finishing operations? The insert’s geometry and WKP35S grade are optimised for productive general milling; finishing performance depends on specific cutting parameters and machine setup, and data-sheet values should be consulted when setting up fine finishing passes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered article is original, brand‑new goods from the manufacturer.
ADMT120420R-F56 WSM35G WSM35G Wendeplatten - Walter Tools
Combining the Tiger·tec Gold wear resistance and the WSM35G carbide grade with a Parallelogram 85° geometry and a 15° clearance angle, this insert delivers stable chip formation and reliable cutting performance when machining stainless steels and heat‑resistant superalloys. Order the ADMT120420R-F56 WSM35G directly via Metav Werkzeuge or consult our specialists for tailored selection advice. ADMT120420R-F56 WSM35G indexable milling insert for hard-to-machine materials, Tiger·tec Gold – Walter Tools The ADMT120420R-F56 WSM35G is an indexable milling insert engineered for productive cutting of stainless steels and heat‑resistant superalloys, combining a wear‑resistant coating with a secure parallelogram seating for repeatable performance. Tiger·tec Gold coated carbide grade WSM35G Optimised for stainless steels and superalloys Parallelogram 85° geometry for secure clamping 15° clearance angle with 2 mm corner radius Longer tool life and secure chip control for demanding materials The combination of the Tiger·tec Gold coating and the WSM35G grade provides elevated wear resistance and thermal stability, which directly reduces flank wear and prolongs usable edge life when cutting tough materials. For materials classified as M (stainless steels) and S (heat‑resistant superalloys and titanium), the coated carbide helps to reduce the risk of built‑up edge and supports consistent chip formation, leading to fewer interrupted cuts and improved process reliability. The result is higher tool utilisation and fewer index changes during a production shift, benefitting cycle time and manufacturing uptime. Geometry that improves clamping stability and surface finish The insert’s Parallelogram 85° geometry combined with a 15° clearance angle is designed to ensure a stable mechanical seat and optimised cutting direction, so the cutter body sees reduced vibration and improved repeatability. The 2 mm corner radius gives a balance between edge strength and surface quality: larger radii strengthen the cutting edge and extend tool life, while the chosen radius maintains acceptable workpiece finish for most milling operations. The integrated F56 chipbreaker is tuned for controlled fragmentation, which simplifies chip evacuation and reduces heat concentration at the cutting edge. Productivity gains and predictable process behaviour When integrated into a machining strategy for difficult‑to‑machine alloys, this indexable insert supports higher cutting parameters with predictable wear patterns, thanks to the coating and grade combination. The insert’s design focuses on reproducible performance rather than one‑off speed bursts, enabling stable feeds and speeds that improve overall shop efficiency. In practice, this translates into fewer rework operations and a more consistent surface integrity on components made from stainless steels or superalloys, which is especially relevant for precision components and repeat production runs. Discuss the selection of Tiger·tec Gold WSM35G inserts with Metav Werkzeuge to ensure the best match for the application and machine setup — contact our specialists at info@metav-werkzeuge.com or call +49 2822 7131930 for precise recommendations Technical Data Article number: ADMT120420R-F56-WSM35G-WALTER Product label: Fräswendeschneidplatte ADMT120420R-F56 WSM35G Walter Tools Manufacturer: Walter Tools Product type: Fräswendeschneidplatte Grade / Sort: WSM35G Series: Tiger-tec Gold Core specifications Clearance angle: 15° Corner radius: 2 mm Plate size: 12 Plate thickness: 04 Geometry: Parallelogram 85° Chipbreaker: F56 Tolerance class: M Features and applications Coating: Tiger·tec Gold Material composition: S / M Suitable for: stainless steels (M) and superalloys/titanium (S) Execution: T Use case: heavy and difficult machining, depending on geometry suitable for stainless steel FAQ What materials is this insert suitable for? The ADMT120420R-F56 WSM35G is suitable for stainless steels (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), due to the thermal stability and wear resistance of the WSM35G grade with Tiger·tec Gold coating. How does the Tiger·tec Gold coating help in production? The Tiger·tec Gold coating increases heat resistance and reduces abrasive wear, which leads to more predictable edge life and improved process security when using this milling insert in continuous production. What advantages does the parallelogram 85° shape provide? The Parallelogram 85° geometry offers a secure clamping position and favourable force distribution in the cutter body, lowering vibration and supporting consistent cutting performance and surface quality. What is the function of the F56 chipbreaker? The F56 chipbreaker is designed to promote controlled chip fragmentation for the targeted material groups, improving chip evacuation and reducing local heat build‑up at the cutting edge. Hersteller: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ADMT120420R-F56 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the versatile WSP45G grade for reliable, long-running milling operations; the robust chip control of the F56 breaker and the 85° parallelogram shape ensure stable cutting conditions and fewer tool changes—order the ADMT120420R-F56 WSP45G directly via Metav Werkzeuge or consult our specialists for production planning ADMT120420R-F56 WSP45G — Fräswendeschneidplatte (indexable milling insert) by Walter Tools, Tiger·tec Gold, for P/M/S applications ADMT120420R-F56 WSP45G is an indexable milling insert designed for demanding milling tasks across steels, rostfreier Stahl and heat-resistant alloys Tiger·tec Gold PVD-coated carbide Versatile for P / M / S material groups Parallelogram 85° for axial/face milling Chipbreaker F56 for secure chip control Reliable cutting performance with long tool life The Tiger·tec Gold coating combined with the WSP45G grade provides a PVD-coated carbide solution optimised for milling. This coating technology enhances wear resistance and thermal stability, which translates into longer service life under cyclic loads. The insert’s composition is suitable for machining unalloyed and alloyed steel, tough rostfreier Stahl and heat-resistant superalloys or titanium. The result is consistent dimensional accuracy and fewer interruptions for tool changes, improving overall process efficiency and reducing per-part cost. Geometry engineered for stable cutting and improved process security The insert’s parallelogram 85° geometry and relief angle 15° give a reliable cutting orientation for both axial and face milling. The corner radius 2 mm strengthens the cutting edge for interrupted cuts and heavy engagement, while the chipbreaker F56 supports controlled chip formation and evacuation. These geometry choices combine to reduce the risk of build-up on the edge and to maintain a stable cutting edge under variable cutting conditions, helping to secure repeatable surface finishes and high process reliability. Versatility that boosts productivity and simplifies inventory With applicability to the P / M / S ISO material groups, this grade reduces the need for multiple specialised inserts in mixed-production environments. The insert is supplied in size code 12 with thickness code 04 and tolerance class M, offering a compact, standardised solution for many milling tasks. Using a single, robust grade for a wide material range shortens set-up time, minimises tool inventory and supports higher machine utilisation—benefits that are particularly important in serial production and jobbing workshops. Clear advantages for planning and machining strategy As a Tiger·tec Gold product from Walter Tools, this insert offers proven coating technology and consistent manufacturing quality. The combination of a strong edge radius, an efficient chipbreaker and a stable geometry supports both roughing and semi-finish operations without sacrificing edge life. For production planners, the key advantage is predictable tool life across varied components, enabling better cycle-time estimation and fewer unscheduled tool changes. If further cutting data or machining parameters are required for specific alloys, technical advisors can provide tailored recommendations. Contact Metav Werkzeuge to discuss specification matching, batch supply and application parameters for the ADMT120420R-F56 WSP45G from Walter Tools Technical data Article number: ADMT120420R-F56-WSP45G-WALTER Designation: ADMT120420R-F56 WPL grade: WSP45G Manufacturer: Walter Tools Numbers / Facts Corner radius: 2 mm Relief angle: 15° Insert size: 12 Thickness code: 04 Tolerance class: M Shape: Parallelogram 85° Chipbreaker: F56 Special features / Versions Coating: Tiger·tec Gold Substrate/grade: PVD-coated carbide Material suitability: P / M / S (steel; rostfreier Stahl; superalloys/Titan) Series: Tiger·tec Gold Application: Milling Execution: T FAQ What materials can this insert machine effectively? The ADMT120420R-F56 WSP45G from Walter Tools is suitable for the ISO material groups P, M and S, covering a broad range from unalloyed and alloyed steel to rostfreier Stahl and heat-resistant superalloys or titanium. How does the chipbreaker F56 influence machining? The chipbreaker F56 supports secure chip formation and evacuation; in combination with the Tiger·tec Gold coating it reduces edge build-up and contributes to a stable cutting process for both roughing and semi-finish operations. Which cutting strategies benefit most from the 85° parallelogram shape? The parallelogram 85° geometry is advantageous for axial and face milling where a positive engagement and consistent chip flow are required; it helps maintain cutting forces and improves surface finish consistency. Is this insert suitable for interrupted cuts? Yes, the corner radius 2 mm and the robust PVD-coated carbide grade make the insert resilient to the mechanical shocks typical of interrupted cutting, offering enhanced edge strength. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. There is no connection between our company and the mentioned brands; the reference to Walter Tools serves explanatory purposes. The offered item is an original, factory-new product of the manufacturer.
ADMT120425L-F56 WKP35S Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Silver coating and the WKP35S grade for durable, high-productivity milling of steel and cast iron; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. ADMT120425L-F56 WKP35S Fräswendeschneidplatte – for Steel and Cast Iron | Walter Tools A ADMT120425L-F56 WKP35S milling indexable insert designed for reliable general milling of steels (P) and cast irons (K), combining a Tiger·tec Silver coating with a robust chipbreaker geometry. Tiger·tec Silver coating for enhanced wear resistance WKP35S grade for steel and cast iron machining Parallelogram 85° form with 15° relief 2.5 mm corner radius for robust edge strength Maximise uptime with proven coating and grade The combination of the Tiger·tec Silver coating and the WKP35S grade provides a reliable balance between wear resistance and edge toughness for mixed-production environments. Designed specifically to handle the thermal and mechanical demands of machining steel and cast iron, this insert sustains cutting performance under interrupted cuts and variable feed conditions. The coated hardmetal substrate reduces flank and crater wear, which in turn supports longer tool life and fewer indexings, contributing to a more continuous production flow and predictable tool-change intervals. Geometry engineered for stable cutting and surface quality A Parallelogram 85° form and 15° relief create a positive cutting geometry that promotes controlled chip formation and consistent contact with the workpiece. The F56 chipbreaker is tuned to the WKP35S grade to encourage short, breakable chips when working cast iron and to manage swarf effectively when machining steels. The 2.5 mm corner radius increases edge robustness, reducing the risk of premature chipping and helping to maintain surface finish quality over extended tool life. These geometric choices reduce vibration and improve process stability in standard face and shoulder milling operations. Practical compatibility and workshop advantages The insert is supplied in the ADMT120425L-F56 format and suits toolholders that accept the parallelogram 85° form; its nominal size 12 and thickness 4 mm ensure compatibility with common milling systems. With a tolerance class M, the component meets production repeatability expectations for industrial settings. Selection of the WKP35S variant simplifies tooling decisions where mixed batches of steel and cast iron are run, lowering inventory complexity while keeping machining results consistent. For specific cutting data and clamping recommendations, Metav Werkzeuge provides application support to match the insert to the cutter body and machining conditions. Contact Metav Werkzeuge for tailored application guidance on Walter Tools inserts and to secure the ADMT120425L-F56 WKP35S for upcoming production runs Technical Data Article number: ADMT120425L-F56-WKP35S-WALTER Name: ADMT120425L-F56 WKP35S Manufacturer: Walter Tools Product type: Fräswendeschneidplatte Series: Tiger-tec Silver Facts Size: 12 mm Thickness: 4 mm Corner radius: 2.5 mm Relief angle: 15° Plate form: Parallelogram 85° Tolerance class: M Special features Coating: Tiger·tec Silver Grade: WKP35S Chipbreaker: F56 Applicable material groups: Steel (P), Cast iron (K) Execution: T Material designation: P / K FAQ What materials is this insert suitable for? The ADMT120425L-F56 WKP35S insert is specified for machining steel (P) and cast iron (K) according to its WKP35S grade and Tiger·tec Silver coating. How does the Tiger·tec Silver coating benefit production? Tiger·tec Silver on the ADMT120425L-F56 WKP35S reduces abrasive and thermal wear, extending service life and improving process reliability in mixed steel and cast-iron applications. Which geometric features improve edge stability? The Parallelogram 85° form combined with a 2.5 mm corner radius and 15° relief on this insert increases edge strength and reduces the likelihood of chipping under interrupted cuts. Is the chipbreaker suitable for both cast iron and steel? Yes; the F56 chipbreaker is matched to the WKP35S grade to encourage short, controllable chips on cast iron while maintaining good swarf control when machining steel. Can this insert be used with standard cutter bodies? The ADMT120425L-F56 format and nominal size align with common milling holders designed for parallelogram inserts; Metav Werkzeuge can advise on exact cutter compatibility. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation. There is no connection between our company and the trademark owners. The offered item is original, factory-new goods of the listed manufacturer.
ADMT120425L-F56 WSP45G Wendeplatten - Walter Tools
The combination of Tiger·tec Gold coating and the robust WSP45G grade delivers high process reliability and consistent tool life for demanding milling operations; the insert’s parallelogram 85° geometry with a 2.5 mm corner radius ensures stable chip control and predictable edge behaviour. Order the original insert via Metav Werkzeuge or request technical advice from the Metav consultants for application-specific support. ADMT120425L-F56 WSP45G Fräswendeschneidplatte by Walter Tools — Tiger·tec Gold, 2.5 mm radius The ADMT120425L-F56 WSP45G is a parallelogram milling insert optimised for productive milling of steel, stainless steel and heat‑resistant alloys under varied cutting conditions. Tiger·tec Gold PVD-coated grade WSP45G Suitable for steel, stainless and superalloys Parallelogram 85° shape with 15° relief Corner radius 2.5 mm for stable cutting edge High productivity through optimised grade and coating The Tiger·tec Gold series combines a modern coating stack with a tough carbide substrate to extend tool life under mixed milling tasks. The WSP45G grade is a PVD‑coated carbide designed to handle the thermal and mechanical loads typical of machining steel, stainless steel and superalloys. This results in reliable edge life and fewer insert changes, which in turn reduces machine downtime and increases effective throughput. The coating reduces adhesion and flank wear, supporting longer uninterrupted production cycles and consistent surface quality on the workpiece. Geometry and chip control that stabilise production processes A carefully chosen geometry turns hard specifications into practical advantages: the parallelogram 85° shape provides positive cutting engagement for versatile milling strategies, while the 15° relief supports smooth entry and exit behaviour at varying depths of cut. The F56 chipbreaker promotes controlled chip formation across a range of feed rates, lowering the risk of built‑up edge and improving surface finish. The 2.5 mm corner radius contributes to a robust cutting edge that tolerates interrupted cuts and contributes to predictable wear patterns, enabling planners to schedule tool changes more efficiently. Application benefits and process security for mixed materials This insert suits both general and demanding milling tasks where material mixes occur or when a single tool needs to cover roughing and semi‑finishing steps. The P / M / S suitability means one insert can address unalloyed and alloyed steel, stainless steel and certain heat‑resistant superalloys or titanium, reducing tool inventory complexity. The standardised geometry and proven grade synergy provide process security: machining parameters can be transferred between machines with minimal rework, supporting reproducible component quality and lower scrap rates in production. For process‑reliable milling with the WSP45G Tiger·tec Gold insert, contact Metav Werkzeuge for application consulting and order support at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: ADMT120425L-F56-WSP45G-WALTER Description: Fräswendeschneidplatte ADMT120425L-F56 WSP45G Manufacturer: Walter Tools Series: Tiger-tec Gold Grade: WSP45G ISO designation: ADMT120425L-F56 WSP45G Facts Relief angle: 15° Corner radius: 2.5 mm Shape: Parallelogram 85° Size: 12 Thickness code: 04 Chipbreaker: F56 Tolerance class: M Special features Coating: Tiger·tec Gold PVD technology Material/grade: PVD-coated carbide (WSP45G) Material suitability: P / M / S Execution: T Series description: Tough, versatile PVD grade for milling FAQ What materials can be machined with this insert? The ADMT120425L-F56 WSP45G insert is rated for steel, stainless steel and superalloys/titanium (P / M / S), making it suitable for mixed‑material milling tasks where a single grade is preferred. Which feature ensures stable chip formation? The F56 chipbreaker combined with the parallelogram 85° geometry and 2.5 mm corner radius promotes controlled chip formation and reduces the risk of built‑up edge during milling. Is this insert suitable for finishing operations? Yes, the PVD‑coated WSP45G grade provides good wear resistance and surface quality, enabling use in semi‑finishing and certain finishing applications depending on cutting data. How does the Tiger·tec Gold coating contribute to tool life? The Tiger·tec Gold coating reduces adhesive wear and improves thermal resistance, which supports longer tool life and consistent cutting performance under variable cutting conditions. What geometry advantages does the insert offer for production? The 15° relief and parallelogram form provide positive cutting engagement and predictable entry/exit behaviour, aiding stable process parameters and easier transfer between machines. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ADMT120425R-F56 WKP35G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating, the WKP35G grade and the F56 chipbreaker for extended tool life and reliable chip control in steel and cast iron milling; the parallelogram 85° geometry and 2.5 mm corner radius ensure stable cutting and reproducible results. Order directly via Metav Werkzeuge or consult our specialists for application-specific advice. ADMT120425R-F56 WKP35G Fräswendeschneidplatte – Tiger·tec Gold, F56 chipbreaker (Walter Tools) The ADMT120425R-F56 WKP35G is an indexable milling insert engineered for productive machining of steel (P) and cast iron (K) with emphasis on process stability and repeatable performance Tiger·tec Gold coating for extended tool life WKP35G grade optimised for steel and cast iron Parallelogram 85° for stable cutting geometry F56 chipbreaker for controlled chip formation Increased productivity through advanced coating and grade The combination of the Tiger·tec Gold coating and the WKP35G cemented-carbide grade delivers measurable productivity gains in medium to heavy steel and cast-iron milling. Coating technology reduces flank wear and improves heat resistance, which translates into longer tool life and fewer index changes. For production-focused workshops this means fewer interruptions and higher output per toolset. The F56 chipbreaker contributes to predictable chip formation, reducing the risk of choke-ups and supporting unattended machining sequences. Overall, the insert supports a balance of durability and material removal rate that suits series production and demanding single-pass operations. Stable geometry for consistent surface quality and process security The Parallelogram 85° form with a 15° clearance and a 2.5 mm corner radius provides a robust cutting edge geometry that promotes stable engagement and consistent surface finish. This geometry helps distribute cutting forces, lowering vibration and protecting the cutting edge under varying depths of cut. The F56 chipbreaker is designed to generate short, controllable chips in both steel and cast iron, aiding chip evacuation and reducing machine downtime. Tolerance class M supports interchangeability and predictable seating in standard toolholders, which simplifies tool management and minimises setup deviations. Application guidance and practical benefits for workshop use Designed for the ISO material groups P (steel) and K (cast iron), this insert suits a wide range of milling tasks from roughing to semi-finishing where robust chip control and tool life are priorities. The insert thickness and insert size provide a stable platform for higher cutting volumes, while the coated grade helps maintain edge integrity under thermally demanding conditions. For selection, match the insert geometry and chipbreaker to the cutter body and machining strategy; the combination of grade, coating and geometry typically improves process repeatability and reduces overall tooling costs through extended service intervals. For tailored recommendations on feeds, speeds and cutter compatibility, technical advice is available. Contact Metav Werkzeuge for specific application advice on Tiger·tec Gold inserts and to arrange supply of the ADMT120425R-F56 WKP35G from Walter Tools — info@metav-werkzeuge.com, +49 2822 7131930 Technical data SKU: ADMT120425R-F56-WKP35G-WALTER Article: ADMT120425R-F56 WKP35G Product type: Fräswendeschneidplatte (milling insert) Brand: Walter Tools Facts Insert size: 12 mm Thickness: 4 mm Relief angle: 15° Corner radius: 2.5 mm Shape: Parallelogram 85° Tolerance class: M Special features Series: Tiger·tec Gold Grade: WKP35G (coated carbide) Chipbreaker: F56 Machinable materials: Steel (P), Cast iron (K) Execution: T FAQ What materials is this insert suited for? The ADMT120425R-F56 WKP35G insert is specified for ISO groups P and K, meaning it is suitable for machining steel and cast iron, leveraging the WKP35G grade and Tiger·tec Gold coating for those materials. How does the F56 chipbreaker affect machining? The F56 chipbreaker on this Walter Tools insert promotes short, controlled chips, improving chip evacuation and reducing the risk of tool or machine stoppages during steel and cast-iron milling. What benefits does the Tiger·tec Gold coating provide? Tiger·tec Gold coating increases wear resistance and thermal stability, extending tool life and supporting higher cutting parameters compared with uncoated grades. Is the insert compatible with standard toolholders for 85° parallelogram inserts? Yes, the parallelogram 85° form and tolerance class M are intended for use with matching standard milling cutter bodies designed for this geometry. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names such as Walter Tools are mentioned for explanation only. There is no affiliation between our company and the named brands. The offered article is an original, brand-new product of the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com