DCGT11T301-FM2 WSM20S FM2 Wendeplatten - Walter Tools
Benefit from reliable chip control, extended tool life and stable cutting performance thanks to the combination of the WSM20S grade and the FM2 chipbreaker; order directly via Metav Werkzeuge or consult our advisers for application support. DCGT11T301-FM2 WSM20S – Turning indexable insert with FM2 chipbreaker for stainless steels and heat‑resistant alloys | Walter Tools The DCGT11T301-FM2 WSM20S is a rhombic 55° turning insert engineered for heavy‑duty machining of stainless steels and heat‑resistant superalloys, offering stable chip formation and consistent edge life Tiger·tec Silver coated carbide WSM20S FM2 chipbreaker for stable chip formation Rhombic 55° form for versatile turning 0.1 mm corner radius and 7° relief angle Built for demanding materials to boost productivity The insert combines the WSM20S grade with the Tiger‑tec Silver coating to provide improved thermal resistance and wear behaviour when machining tough alloys. This technical pairing promotes stable chip formation and reduces flank wear, which in turn extends tool life and reduces downtime for insert changes. For busy production environments, the result is a measurable improvement in process reliability and feeding rates, making the component a practical choice where consistent performance under thermal load is essential. Geometry that delivers precision and repeatability Its rhombic 55° shape together with a 0.1 mm corner radius and 7° relief angle ensures predictable engagement and secure seating in standard holders. The FM2 chipbreaker supports controlled chip segmentation, lowering the risk of built‑up edge and helping to maintain surface integrity on the workpiece. These geometric decisions translate directly into better dimensional repeatability and a superior surface finish in serial turning operations, while keeping machine cycles efficient. Integration into production workflows and handling guidance Designed as a direct replacement in compatible toolholders, this insert suits both roughing operations in high mechanical load conditions and finishing passes where edge stability matters. The coated carbide substrate is optimised for workpiece groups M and S — stainless steels and heat‑resistant alloys — offering a broad application window across aerospace and industrial components. For cutting data and holder recommendations, Metav Werkzeuge can provide tailored guidance ensuring the insert is deployed to its full potential in specific machining setups. For precise selection and application advice on Walter Tools Tiger‑tec Silver inserts such as this DCGT11T301-FM2 WSM20S, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and immediate availability. Technical Data SKU: DCGT11T301-FM2-WSM20S-WALTER Article designation: DCGT11T301-FM2 WSM20S Manufacturer: Walter Tools Series: Tiger‑tec Silver Facts Plate size: 11 Corner radius: 0.1 mm Relief (free) angle: 7° Plate thickness: T3 Plate form: Rhombus 55° Tolerance class: G Special features Grade: WSM20S Coating technology: Tiger‑tec Silver Chipbreaker: FM2 Material suitability: stainless steels (M) Material suitability: heat‑resistant superalloys / titanium (S) FAQ Which materials can this insert machine effectively? The DCGT11T301‑FM2 WSM20S insert is specified for stainless steels (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), with the Tiger‑tec Silver coating aiding thermal stability. What are the key geometry values of the insert? This turning insert features a rhombic 55° form, a 0.1 mm corner radius and a 7° relief angle, providing controlled engagement and repeatable cutting behaviour for serial machining. What chip control does the insert offer? Equipped with the FM2 chipbreaker, the insert promotes stable chip formation and reduces the likelihood of built‑up edge, improving surface quality and process stability. Is this insert suitable for heavy roughing operations? Yes, the combination of WSM20S grade and Tiger‑tec Silver coating makes the DCGT11T301‑FM2 suitable for demanding, heavy‑cut applications on tough alloys where edge strength and heat resistance are required. Which toolholders are compatible with this insert? The insert’s rhombic 55° geometry and ISO designation allow use in standard turning toolholders designed for DCGT‑style indexable plates; check holder seat compatibility and clamping type before mounting the DCGT11T301‑FM2 WSM20S. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCGT11T301-FN2 WNN10 Wendeplatten - Walter Tools
Take advantage of the combination of coated cemented carbide WNN10, a precise 0.1 mm corner radius and a controlled FN2 chipbreaker for steady chip formation and reliable turning results — order directly via Metav Werkzeuge or consult the specialists for application support. DCGT11T301-FN2 WNN10 — indexable turning insert, rhombic 55° form, Walter Tools The DCGT11T301-FN2 WNN10 is a coated cemented carbide indexable turning insert engineered for general turning applications where stable chip control and repeatable surface quality are required. Coated cemented carbide WNN10 Rhombic 55° geometry for stability 0.1 mm corner radius for fine finishes FN2 chipbreaker for controlled chips Maximise process stability and tool life The combination of a coated cemented carbide grade (WNN10) and a well-defined chipbreaker (FN2) delivers consistent material removal with reduced edge wear. The insert’s rhombic 55° form and the modest clearance angle of 7° contribute to reliable cutting engagement and predictable forces on the toolholder. For production-oriented workshops and CNC turning centres, this means longer intervals between index changes and fewer unscheduled tool interventions, improving overall machining efficiency. Achieve consistent surface finish and chip control A 0.1 mm corner radius provides a balance between edge strength and the ability to obtain fine finishes on turned components. The FN2 chipbreaker is designed to break and evacuate chips effectively across a variety of turning parameters; this reduces rework and minimises the risk of chip interference on complex or long-running jobs. Where surface integrity and repeatability matter, the controlled geometry helps engineers hit tolerances with fewer process adjustments. Practical integration and application advice The insert is supplied in the T3 thickness execution and the standard size 11, compatible with common insert clamping systems. The grade is described as a coated cemented carbide; suitability for specific workpiece materials should be verified against the manufacturer’s matrix. For machining planning, note the tolerance class G and use the specified insert geometry to match cutting data — this reduces trial cuts and shortens setup time in serial production. Contact Metav Werkzeuge for tailored recommendations on Walter Tools inserts and to discuss stock availability — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: DCGT11T301-FN2-WNN10-WALTER ISO designation: DCGT11T301-FN2 WNN10 Short designation: DCGT11T301-FN2 Manufacturer: Walter Tools Core technical data Clearance angle: 7° Corner radius: 0.1 mm Insert size: 11 Thickness code: T3 Tolerance class: G Special features Coated cemented carbide grade WNN10 Chipbreaker: FN2 Rhombic 55° insert form Execution: T Series: Walter Schneidstoffsorte - Serie offen Material: catalogue dependent Application note: verify workpiece suitability in the product matrix FAQ What materials is this insert intended for? The DCGT11T301-FN2 WNN10 is a coated cemented carbide insert; material suitability depends on the specific workpiece and should be checked against the Walter Tools application matrix. How does the FN2 chipbreaker affect machining? The FN2 chipbreaker promotes short, controllable chips under a wide range of cutting conditions, improving evacuations and reducing the likelihood of chip-related surface damage. What finish can be expected with a 0.1 mm corner radius? A 0.1 mm corner radius offers a compromise between edge strength and surface quality — suitable for good finishes on turned parts while maintaining sufficient edge robustness for many general applications. Is this insert compatible with standard insert holders? The insert uses a common rhombic 55° form and size 11 designation; compatibility with holders should be confirmed against the holder’s insert pocket and clamping specifications. Where can the official grade information be obtained? Detailed grade and coating information for WNN10 is provided by Walter Tools; consult the product matrix or contact Metav Werkzeuge for the manufacturer’s technical datasheet. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names such as Walter Tools and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is an original, brand-new product from the manufacturer. The Walter AG (brand appearance: Walter Tools) is part of the Sandvik Group.
DCGT11T301-MN2 WN10 Wendeplatten - Walter Tools
Die Kombination aus WN10-Hartmetall, präziser Rhombus-Form und dem MN2-Spanbrecher sorgt für verlässliche Spanbildung und konstante Oberflächengüte; die Ausführung T plus Toleranzklasse G ermöglicht reproduzierbare Einsetzbarkeit in standardisierten Werkzeughaltern. Bestellungen und Anfragen lassen sich direkt über Metav Werkzeuge klären oder durch technische Beratung absichern. DCGT11T301-MN2 WN10 — Turning indexable insert, Rhombus 55°, MN2 chipbreaker | Walter Tools A DCGT11T301-MN2 WN10 turning insert designed for stable general-purpose turning with a 55° rhombic geometry and integrated MN2 chip control. Uncoated carbide WN10 grade Rhombic 55° geometry 0.1 mm corner radius for fine turning MN2 chipbreaker for reliable chip control Stable chip control for consistent cycle times The integrated MN2 chipbreaker is developed to promote predictable chip formation and evacuation. By managing chip shape and flow, the chipbreaker reduces the risk of chip entanglement and tool interruptions, which in turn contributes to steadier cycle times and fewer part reworks. For production environments where uninterrupted operation is essential, this feature supports process reliability and improves overall machining efficiency. Geometry that supports precise finishing operations The Rhombus 55° profile combined with a 0.1 mm corner radius and a 7° relief angle delivers a balance between robustness and fine surface quality. The acute geometry enables access to narrow contours while the small nose radius favours a fine surface finish on turned components. The specified tolerance class G denotes consistent dimensional conformity, which helps to maintain repeatable machining results when inserts are rotated or replaced. Economical grade with clear specification advice The insert is supplied in the WN10 grade, an uncoated carbide composition from the Walter tooling series. This material choice typically offers cost-effective performance for a range of general turning tasks; however, material-specific suitability should be verified against the manufacturer's product matrix. The open series designation (Walter Schneidstoffsorte - Serie offen) indicates a standardised, broadly applicable grade designed for practical use across workshop scenarios. Simple integration and handling in production Marked as DCGT11T301-MN2, the insert corresponds to common holder systems for 11-size rhombic tooling and a T3 thickness that supports secure clamping and heat dissipation. The clear, standardised designation simplifies stock management and tool change procedures, while the execution code T and the chip control features make the insert suitable for structured production setups where tool life and reproducibility are priorities. Contact Metav Werkzeuge for tailored application advice on Walter Tools WN10 inserts and to confirm compatibility with existing toolholders — eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 Technical data Article number: DCGT11T301-MN2-WN10-WALTER Name: DCGT11T301-MN2 WN10 Product type: Drehwendeschneidplatte Manufacturer: Walter Tools Core specifications Plate size: 11 Thickness: T3 Corner radius: 0.1 mm Relief angle: 7° Plate form: Rhombus 55° Features Chipbreaker: MN2 Grade: WN10 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Tolerance class: G Design/execution: T FAQ What is the purpose of the MN2 chipbreaker? The MN2 chipbreaker on the DCGT11T301-MN2 WN10 insert is designed to shape and control chips for safe evacuation, reducing re-cutting and improving cycle stability. What does the WN10 designation indicate? WN10 denotes the Walter Tools carbide grade used for this insert; it is an uncoated grade intended for broad application — material-specific suitability should be checked against the manufacturer matrix. How does the 0.1 mm corner radius affect results? A 0.1 mm nose radius favours fine surface finishes and reduced cutting forces for finishing passes, while still offering enough strength for light roughing when managed appropriately. Is this insert compatible with standard DCGT11 holders? Yes, the DCGT11T301-MN2 designation and T3 thickness align with common 11-size rhombic holders; verification against the specific holder catalogue is recommended before fitting. What does the tolerance class G mean for repeatability? Tolerance class G indicates manufacturing tolerances that support consistent seating and repeatable part quality when inserts are indexed or replaced. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCGT11T301-MN2 WNN10 WNN10 Wendeplatten - Walter Tools
Take advantage of the combination of precise geometry and reliable chip control for efficient turning operations; purchase the insert directly via Metav Werkzeuge or contact our consultants for application advice. DCGT11T301-MN2 WNN10 turning insert — MN2 chipbreaker, Rhombic 55° by Walter Tools The DCGT11T301-MN2 WNN10 is a coated carbide turning insert designed for versatile turning tasks where a rhombic 55° geometry and a fine 0.1 mm corner radius are required Coated carbide for wide material range Rhombic 55° form for flexible approach angles 0.1 mm corner radius for fine surface finishes MN2 chipbreaker for consistent chip control Increase throughput with controlled chip formation The combination of a coated carbide grade and the MN2 chipbreaker makes this insert ideal for reducing interruptions during production. The engineered chipbreaker channels and breaks chips reliably, which minimises rework and tool change frequency. For routine and batch turning, the stable chip flow contributes to higher productive time and predictable cycle lengths. Explanation: a chipbreaker shapes the chips so they evacuate safely, preventing snarl-ups and protecting the toolholder from built-up edge. Achieve repeatable finishes from compact geometry A Rhombic 55° profile together with a 0.1 mm corner radius delivers access to profiles and controlled cutting engagement that benefit finishing passes. The modest radius supports a balance between edge strength and surface quality; it lowers cutting forces compared with larger radii while still avoiding fragile edges. The relief angle 7° ensures adequate clearance behind the cutting edge, reducing rubbing and heat generation during light to medium cuts. These geometry features help to obtain consistent surface results with less manual correction. Versatile grade selection for varied applications The WNN10 grade is specified as a coated carbide family within Walter’s open series; it is intended for a broad material spectrum—please verify the product matrix for precise material compatibility. The insert designation and the T3 thickness permit straightforward seat and clamp-up in common holders engineered for ISO-style rhombic inserts. For shops aiming to consolidate tooling, this indexable option supports an economical approach: reduced inventory variety combined with robust performance for general turning and finishing tasks. For machining enquiries or to secure these Walter Tools turning inserts, contact Metav Werkzeuge to request a tailored recommendation and ordering assistance via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: DCGT11T301-MN2-WNN10-WALTER Name: DCGT11T301-MN2 WNN10 Manufacturer: Walter Tools Product type: turning insert Series: Walter cutting grade - open series Facts Insert size: 11 Corner radius: 0.1 mm Relief angle: 7° Thickness: T3 Tolerance class: G Special features Chipbreaker: MN2 Plate form: Rhombus 55° Grade: WNN10 (coated carbide) Base designation: DCGT11T301-MN2 FAQ What machining tasks is this insert suited for? The DCGT11T301-MN2 WNN10 turning insert is suitable for general turning and finishing operations where a rhombic approach and fine corner radius are required; check the WNN10 grade matrix for specific material recommendations. How does the MN2 chipbreaker improve performance? The MN2 chipbreaker on this insert controls chip shape and evacuation, reducing interruptions and improving process stability when using the DCGT11T301-MN2 WNN10 in series production. What does the 0.1 mm corner radius mean for surface quality? A 0.1 mm corner radius offers a compromise between edge strength and surface finish, enabling finer finishes with lower cutting forces compared with larger radii on the same insert type. Can this insert be used for light finishing and roughing? Yes, the combination of Rhombic 55° geometry and the WNN10 coated carbide grade allows flexible use from light finishing to general turning; adaptability depends on cutting parameters and the specific material in the product matrix. Is the grade WNN10 a coated carbide? Yes, WNN10 is specified as a coated carbide grade within Walter’s series and is optimised for a broad workpiece material range; final suitability should be confirmed against the manufacturer’s product matrix. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are used here for identification and explanation only. There is no affiliation or connection implied between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
DCGT11T301-MN2 WSM01 MN2 Wendeplatten - Walter Tools
Take advantage of a high‑performance Tiger‑tec Silver grade and an MN2 chipbreaker to secure stable chip formation and extended tool life when machining stainless steel and difficult alloys; order the insert directly via Metav Werkzeuge or consult our specialists for application‑specific cutting data. DCGT11T301‑MN2 WSM01 — Turning insert, Rhombus 55°, 0.1 mm corner radius — Walter Tools DCGT11T301‑MN2 WSM01 is a rhombic turning insert engineered for the productive machining of stainless steel and heat‑resistant superalloys, offering a 7° relief and a compact 0.1 mm corner radius for controlled finishing. *Tiger‑tec Silver coating for extended wear life *Optimised MN2 chipbreaker for stable chips *Rhombic 55° shape with 0.1 mm corner radius *Suitable for stainless steel and superalloys Greater process reliability in demanding materials The combination of Tiger‑tec Silver grade and the WSM01 substrate provides improved resistance to abrasion and thermal load, which benefits operations on stainless steel and high‑temperature alloys. The coated hardmetal composition promotes stable chip formation, reducing the risk of build‑up edge and unexpected tool changeovers. For machining tasks where material toughness and temperature sensitivity are critical, this insert offers a predictable service life and consistent dimensional performance, helping to maintain cycle times and reduce overall tooling costs. Predictable surface quality and chip control An MN2 chipbreaker, paired with the Rhombus 55° geometry and a 0.1 mm corner radius, delivers fine control over chip shape and evacuation, which directly improves surface finish on turned components. The 7° relief angle reduces friction behind the cutting edge, lowering cutting forces and heat generation. These features make the insert well suited to finishing and semi‑finishing operations on demanding workpieces, where repeatable surface integrity and minimal post‑processing are required. Shop‑floor efficiency and straightforward integration With a standard ISO designation and tolerance class G, the insert supports fast indexing and reproducible set‑ups across toolholders that accept the DCGT form. The compact geometry and robust edge make replacement quick and predictable, reducing machine downtime. The grade’s balance of wear resistance and edge stability aids longer intervals between changes, which contributes to steady productivity and easier planning of tool inventories in production environments. For secure, high‑quality machining of stainless steel and superalloys, rely on Walter Tools Tiger‑tec Silver inserts — contact Metav Werkzeuge for tailored cutting parameters and purchase assistance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: DCGT11T301‑MN2‑WSM01‑WALTER Item description: Drehwendeschneidplatte DCGT11T301‑MN2 WSM01 Walter Tools Manufacturer: Walter Tools Series: Tiger‑tec Silver Grade: WSM01 Facts Shape: Rhombus 55° Size: 11 Corner radius: 0.1 mm Relief angle: 7° Thickness: T3 Chipbreaker: MN2 Tolerance class: G Special features Coated hardmetal grade for improved wear resistance Designed for stainless steel and high‑temperature alloys Optimised for stable chip formation and surface quality Compact geometry for finishing and semi‑finishing FAQ Which materials are best suited for this insert? The DCGT11T301‑MN2 WSM01 insert is designed primarily for stainless steel and heat‑resistant superalloys; the Tiger‑tec Silver grade supports machining where thermal resistance and edge stability are required. What is the purpose of the MN2 chipbreaker? The MN2 chipbreaker on this insert controls chip segmentation and evacuation to reduce build‑up edge and improve surface finish during turning operations. How does the 0.1 mm corner radius affect finishing? A 0.1 mm corner radius provides a fine cutting edge that improves surface quality and reduces cutting forces in finishing passes when using the DCGT11T301‑MN2 WSM01 insert. Can this insert be used in standard DCGT toolholders? Yes, the ISO‑standard DCGT form and tolerance class G make the insert compatible with holders designed for DCGT inserts, allowing straightforward replacement and repeatable set‑ups. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCGT11T301M-FP2 WEP10C WEP10C Wendeplatten - Walter Tools
Take advantage of the combination of Walter Cermet cutting performance, precise FP2 chip control and the compact Rhombic 55° form for consistent finishing results; order the inserts directly via Metav Werkzeuge or consult our specialists for application guidance. DCGT11T301M-FP2 WEP10C Turning Insert, Rhombus 55° (11 mm) – Walter Tools A DCGT11T301M-FP2 WEP10C turning insert engineered for precision finishing and stable chip control in general turning applications. Walter Cermet grade WEP10C for long tool life FP2 chipbreaker for controlled chip formation Rhombic 55° geometry for versatile turning 7° clearance angle and 0.1 mm nose radius Consistent finishing with cermet precision and wear resistance The Walter Cermet WEP10C grade delivers a balance between wear resistance and edge stability that benefits finishing operations. As a cermet-based cutting material, it combines ceramic hardness with metallic toughness to maintain a sharp cutting edge over prolonged cycles, which reduces rework and tool changes. This results in higher process reliability and a more predictable surface quality. The economic advantage is twofold: fewer interruptions in production and a lower effective tooling cost per component when integrated into standard finishing cycles. Stable chip control and geometry for reliable machining The FP2 chipbreaker is designed to produce short, controllable chips under a range of finishing conditions, improving surface integrity and reducing the risk of entanglement in automated turning cells. The Rhombic 55° insert form provides flexibility for both light profiling and fine turning, while the 7° clearance and 0.1 mm nose radius support low cutting forces and fine surface finishes. Together these geometric elements enhance process stability, simplify fixture setup and help to achieve repeatable part tolerances with minimal operator adjustment. Practical integration and benefits in manufacturing workflows With a standard format and T3 thickness, this insert fits common DCGT-style toolholders and is straightforward to specify in existing tool inventories. Tolerance class G indicates consistent dimensional accuracy for predictable clamping and indexing. The compact 11 mm inscribed circle makes it suitable where space and tool overhang are constrained, delivering dependable performance in both single-pass finishing and multi-step production routines. For application compatibility consult the manufacturer matrix to determine the ideal workpiece materials and cutting parameters. Contact Metav Werkzeuge for tailored selection advice and availability of DCGT11T301M-FP2 WEP10C inserts; specialists will assist with application data and supply options – eMail: info@metav-werkzeuge.com / Tel: +49 2822 7131930 Technical data SKU: DCGT11T301M-FP2-WEP10C-WALTER Designation: DCGT11T301M-FP2 WEP10C Manufacturer: Walter Tools Facts Insert form: Rhombus 55° Inscribed circle: 11 mm Relief angle: 7° Nose radius: 0.1 mm Thickness: T3 Tolerance class: G Special features Chipbreaker: FP2 Grade: WEP10C Series: Walter Cermet Execution: T ISO designation: DCGT11T301M-FP2 WEP10C Format: turning insert FAQ What are the main advantages of the WEP10C grade? The WEP10C grade offers the wear resistance and edge stability typical of Walter Cermet, making the DCGT11T301M-FP2 WEP10C insert suited to finishing operations where consistent surface quality and tool life matter. How does the FP2 chipbreaker improve machining? The FP2 chipbreaker on the DCGT11T301M-FP2 WEP10C produces short, controlled chips, reducing entanglement and improving process safety and surface integrity during precision turning. Which operations are best suited to this insert form? Rhombic 55° geometry and a 0.1 mm nose radius make this insert ideal for finishing and light profiling where fine surface finishes and dimensional repeatability are required. Will this insert fit standard toolholders? The DCGT11T301M-FP2 WEP10C follows common DCGT insert dimensions and, with its T3 thickness, is compatible with standard clamping systems designed for rhombic 55° turning inserts. What dimensional tolerances and features should be noted? Key specifications for this insert include a 7° clearance angle, 0.1 mm nose radius, 11 mm inscribed circle and tolerance class G; these determine fit and expected clamping accuracy. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used for explanation only. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
DCGT11T302-FL2 WSM01 WSM01 Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Silver series and the WSM01 grade to secure stable chip formation and extended cutting-edge life when machining difficult materials; the rhombic 55° form with a 0.2 mm corner radius and FL2 chipbreaker reduces rework and supports consistent surface quality. Order the insert directly via Metav Werkzeuge or consult the Metav team for application-specific guidance. DCGT11T302-FL2 WSM01 turning insert by Walter Tools — Tiger‑tec Silver, FL2 chipbreaker The DCGT11T302-FL2 WSM01 is a rhombic 55° turning insert designed for machining rostfreier Stahl and heat‑resistant superalloys, combining a stable cutting edge with a chipbreaker tuned for secure chip control Tiger‑tec Silver for thermal stability FL2 chipbreaker for controlled chips Rhombic 55° form for versatile turning Suitable for stainless steel and superalloys High‑performance grade for demanding materials The WSM01 grade from the Tiger‑tec Silver series delivers a balance between toughness and wear resistance, making it suitable for demanding turning applications. The coated carbide composition and the engineered chipbreaker improve chip control and reduce the risk of built‑up edge when facing materials that generate high temperatures and work‑hardening. This results in a more predictable machining process and fewer interruptions for tool changes, supporting higher productivity in serial production or small‑batch runs. Geometry that improves surface finish and process stability The rhombic 55° form coupled with a 0.2 mm corner radius and 7° clearance angle provides a compromise between strength and accessibility in confined turning operations. The modest corner radius supports improved edge life while still maintaining the capability for fine surface finishes at typical finishing feeds. The plate thickness T3 and size designation 11 contribute to a rigid clamping condition that minimises vibration and enhances dimensional repeatability in turned parts. Optimised chip formation and tool life The FL2 chipbreaker is tuned to produce short, controllable chips across a range of depths of cut common in stainless steels and nickel‑base alloys. Stable chip formation reduces workpiece surface damage and helps preserve the integrity of the cutting edge, which in turn lengthens consistent tool life and reduces overall production cost per part. This technical combination supports a higher degree of process security in challenging cut conditions and when machines operate at varying power levels. Practical application notes and selection guidance Intended primarily for rostfreier Stahl (ISO group M) and heat‑resistant alloys (ISO group S), the insert performs best when matched with appropriate cutting parameters and coolant strategies for the workpiece material. Selection of the WSM01 grade and the FL2 chipbreaker should be based on the workpiece alloy and the intended machining task—roughing or finishing—since geometry and grade interact to determine final surface quality and tool longevity. For further support on parameter selection, Metav Werkzeuge provides application advice and cutting data. For reliable machining of rostfreier Stahl and superalloys, contact Metav Werkzeuge to request the DCGT11T302-FL2 WSM01 insert from Walter Tools and obtain tailored cutting recommendations. Technical data SKU: DCGT11T302-FL2-WSM01-WALTER ISO designation: DCGT11T302-FL2 WSM01 Manufacturer: Walter Tools Facts Plate form: Rhombus 55° Plate size: 11 Corner radius: 0.2 mm Clearance angle: 7° Plate thickness: T3 Tolerance class: G Special features Series: Tiger‑tec Silver Grade: WSM01 (coated carbide) Chipbreaker: FL2 Execution: T Suitable materials: rostfreier Stahl (ISO M), heat‑resistant superalloys and titanium (ISO S) Product type: turning insert FAQ What materials is this insert intended for? The DCGT11T302-FL2 WSM01 is specified for rostfreier Stahl (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), offering tailored performance for these workpiece materials. How does the FL2 chipbreaker benefit production? The FL2 chipbreaker on the DCGT11T302-FL2 WSM01 produces controlled, short chips, which improves shopfloor safety and reduces the likelihood of surface damage, supporting longer uninterrupted machining cycles. What is the advantage of the rhombic 55° form? The Rhombus 55° geometry provides flexibility for a range of turning tasks, combining good accessibility with stable cutting conditions to achieve consistent surface quality. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (marketed as Walter Tools) is part of the Sandvik Group and is a leading provider of precision tools for metalworking. Protected trademarks and trade names belong to their respective owners. Mention of brand names is for explanation only; no affiliation is implied.
DCGT11T302-FM2 WMP20G WMP20G Wendeplatten - Walter Tools
Benefit from a combination of high process security and long tool life thanks to the Tiger·tec Gold grade and the FM2 chipbreaker; the insert delivers stable chip control when machining stainless steels and fits standard clamping systems — order directly via Metav Werkzeuge or consult our specialists for application advice. DCGT11T302-FM2 WMP20G turning insert — Rhombic 55°, Tiger·tec Gold for stainless steel (Walter Tools) The DCGT11T302-FM2 WMP20G is a rhombic 55° turning insert crafted for reliable machining of rostfreie Stähle under medium to robust conditions, combining a wear-resistant coating with a chipformer tailored for secure swarf evacuation. Tiger·tec Gold coated for improved edge life Optimised for stainless steel (group M) FM2 chipbreaker for secure chip control Rhombic 55° shape, 0.2 mm corner radius Predictable performance for stainless steel operations The combination of the Tiger·tec Gold coating and a coated carbide substrate provides measurable advantages when working with stainless steel: improved resistance to built-up edge and enhanced wear behaviour, which helps to maintain cutting geometry over longer cycles. This stability reduces variance in part quality and minimises unscheduled tool changes, supporting consistent batch throughput and improved process reliability for series production. Geometry that balances cutting forces and surface finish Featuring a Rhombic 55° form with a 0.2 mm corner radius and a 7° clearance angle, the insert is shaped to reduce cutting forces while preserving tool strength at the edge. The FM2 chipbreaker assists controlled chip formation on ductile, heat-generating materials, leading to better surface integrity and reduced rework. The geometry supports predictable contact conditions, which is particularly valuable for repeatable finishing operations. Enhanced tool life and production economy The insert’s grade WMP20G, part of the Tiger·tec Gold series, is engineered for mid-to-heavy duty applications in the ISO M group; this translates into reliable tool life under variable cutting conditions. Fewer tool changes and consistent cutting behaviour contribute directly to lower downtime and higher overall equipment effectiveness (OEE), making the component a pragmatic choice for manufacturers seeking a balance between performance and cost-efficiency. Practical compatibility and handling notes Designed as a standard-sized insert, the component fits conventional indexable tooling systems that accept the DCGT profile; the T3 thickness and Rhombic 55° footprint permit use across a broad range of toolholders. For optimal results in stainless-steel turning, ensure stable workpiece clamping and appropriate cooling strategy to manage heat and extend edge life. The insert is intended for the ISO M material group and is supplied in tolerance class G, supporting predictable mounting and repeatability in multi-insert assemblies. Contact Metav Werkzeuge for tailored cutting data and application support on Walter Tools Tiger·tec Gold inserts; request a material-specific recommendation via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: DCGT11T302-FM2-WMP20G-WALTER Article designation: DCGT11T302-FM2 ISO designation: DCGT11T302-FM2 WMP20G Product type: Drehwendeschneidplatte Brand: Walter Tools Facts Insert size: 11 mm Corner radius: 0.2 mm Clearance angle: 7° Thickness: T3 Tolerance class: G Special features Grade: WMP20G (Tiger·tec Gold series) Chipbreaker: FM2 Shape: Rhombus 55° Substrate: coated carbide Material application: suitable for rostfreie Stähle FAQ What materials is this insert suitable for? The DCGT11T302-FM2 WMP20G from Walter Tools is designed primarily for rostfreie Stähle (ISO M) and performs well under medium to robust machining conditions. How does the FM2 chipbreaker affect machining of stainless steel? The FM2 chipbreaker on the Walter Tools insert promotes secure chip control and reduced tendency for built-up edge during stainless-steel turning, improving surface quality and process stability. Is this insert compatible with standard DCGT toolholders? Yes, the insert follows the DCGT profile and T3 thickness, making it compatible with toolholders that accept DCGT11T302-style inserts when mounted according to the holder manufacturer’s instructions. What advantages does the Tiger·tec Gold coating provide? Tiger·tec Gold enhances wear resistance and edge stability under the high thermal and adhesive stresses common in stainless-steel turning, extending cutting intervals and ensuring more consistent part quality with the WMP20G grade. Which SKU should be ordered for this specification? Order SKU DCGT11T302-FM2-WMP20G-WALTER to obtain the rhombic 55° insert in the WMP20G Tiger·tec Gold grade from Walter Tools. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned for explanatory purposes only; no connection between our company and the named manufacturers is implied. The offered article is an original, factory-new product of the stated manufacturer.
DCGT11T302-FM2 WSM01 WSM01 Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Silver combination of wear-resistant coating and the WSM01 grade to secure stable chip formation and extended tool life for demanding turning tasks; order the insert directly via Metav Werkzeuge or request application advice from the consultants for process optimisation. DCGT11T302-FM2 WSM01 turning indexable insert by Walter Tools — coated carbide for rostfreier Stahl and high-temperature alloys, Rhombus 55° form DCGT11T302-FM2 WSM01 is a turning indexable insert designed for heavy-duty and temperamental materials, delivering reliable edge stability in continuous production. Tiger‑tec Silver coating WSM01 grade for tough alloys Stable chip formation, long life 7° clearance, 0.2 mm corner radius High-performance coating and grade for consistent productivity The Tiger‑tec Silver series delivers a balanced coating and substrate pairing that supports predictable performance in challenging operations. The insert’s WSM01 grade is a coated carbide developed to resist thermal and mechanical wear during the machining of rostfreier Stahl and heat‑resistant superalloys; this reduces the need for frequent tool changes and helps maintain cycle-time stability. The result is measurable process efficiency: fewer interrupted runs and improved component throughput without sacrificing dimensional control. Geometry engineered for stable cutting and chip control The Rhombus 55° form combined with the FM2 chipbreaker enables controlled chip formation even under variable cutting conditions. The modest 7° clearance angle and 0.2 mm corner radius contribute to a secure cutting edge that tolerates interrupted cuts and fluctuating feeds, which is particularly beneficial when machining sticky or work‑hardening materials. With the insert’s geometry, set-up times are reduced and surface finish consistency is improved, supporting predictable downstream processes. Application guidance and benefits for workshop planning This insert is intended for applications involving rostfreier Stahl and materials classified in the S‑group (high‑temperature alloys and titanium), offering operators the edge stability and heat resistance required for such alloys. The size 11 format and T3 thickness suit common turning toolholders, simplifying inventory management. For procurement and process planning, the combination of robust substrate, targeted coating and optimised chip control translates into lower overall machining costs through extended tool life and reduced scrap rates. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger‑tec Silver inserts and process parameter suggestions — email info@metav-werkzeuge.com or call +49 2822 7131930 for application support Technical data SKU: DCGT11T302-FM2-WSM01-WALTER Designation: DCGT11T302-FM2 WSM01 Product type: Turning indexable insert Brand: Walter Tools Facts Clearance angle: 7° Corner radius: 0.2 mm Insert form: Rhombus 55° Size: 11 Thickness: T3 Chipbreaker: FM2 Tolerance class: G Special features Series: Tiger‑tec Silver Grade: WSM01 (coated carbide) Suitable for: rostfreier Stahl; high‑temperature alloys and titanium (S and M groups) Stable chip formation and edge life Designed for productive turning of difficult‑to‑machine materials FAQ What materials is this insert suitable for? The Walter Tools DCGT11T302-FM2 WSM01 insert is suitable for machining rostfreier Stahl and S‑group materials such as heat‑resistant superalloys and titanium. What does the WSM01 grade provide? The WSM01 grade offers a coated‑carbide combination optimised for thermal resistance and edge stability, improving performance when cutting sticky or heat‑prone materials. Which insert geometry helps with chip control? The combination of Rhombus 55° form and the FM2 chipbreaker promotes controlled chips and consistent surface finish in turning operations. What are the key dimensional specifications to check for toolholder compatibility? Key specifications include the size 11, T3 thickness, 0.2 mm corner radius and the 7° clearance angle; confirm these against the toolholder data sheet. Can this insert be used for interrupted cuts? Yes; the insert’s geometry and grade deliver edge robustness suitable for interrupted cutting in rostfreier Stahl and similar alloys. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Die Walter AG (brand presentation: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned for explanation only. There is no connection between our company and the named brands. The offered item is an original factory‑new product of the manufacturer.
DCGT11T302-FM2 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, FM2 chipbreaker geometry and a compact Rhombus 55° form for stable chip control and secure performance in machining stainless steels and heat‑resistant alloys; order directly via Metav Werkzeuge or consult our specialists for application support. DCGT11T302-FM2 WSM10S indexable turning insert – Rhombus 55°, 7° clearance, Walter Tools The DCGT11T302-FM2 WSM10S is an indexable turning insert optimised for tough-to-machine materials, offering a compact Rhombus 55° form and a 7° clearance angle for secure edge engagement in interrupted or continuous turning operations. Tiger·tec Silver coated cemented carbide FM2 chipbreaker for stable chips 0.2 mm corner radius for finish turning Suitable for ISO groups M and S Consistent performance on stainless steels and superalloys The combination of the WSM10S grade and the Tiger·tec Silver technology delivers stable chip formation and high thermal resistance when machining stainless steels and heat‑resistant alloys. The coated cemented carbide substrate resists edge wear and supports predictable tool life, which translates into fewer insert changes and more predictable production cycles. This makes the insert particularly suitable for components where surface integrity and dimensional consistency are critical. Design that supports reliable cutting and surface quality The Rhombus 55° geometry with a 0.2 mm corner radius and a 7° clearance angle provides a stable cutting edge with controlled engagement, reducing the tendency for built‑up edge on adhesive materials. The FM2 chipbreaker promotes short, manageable chips under typical turning conditions, lowering the risk of workpiece damage and facilitating safer chip evacuation. These design choices improve process reliability and help achieve consistent surface finish with reduced secondary operations. Practical use and application advice for machining tasks This indexable insert is supplied in the DCGT form factor and is intended for turning operations on components made from rostfreier Stahl and nickel‑based or titanium alloys (ISO groups M and S). The insert’s coated surface and robust substrate support higher cutting temperatures and provide wear resistance during serial production. For selection of complementary tool holders and recommended cutting parameters, Metav Werkzeuge’s application consultants can advise on feed and speed ranges tailored to the specific alloy and part geometry. Contact Metav Werkzeuge for application guidance and to order Walter Tools Tiger·tec Silver inserts; expert advice and quick availability from Metav Werkzeuge ensure the right insert for the job Technical data Article number: DCGT11T302-FM2-WSM10S-WALTER Label: Drehwendeschneidplatte DCGT11T302-FM2 WSM10S Walter Tools ISO designation: DCGT11T302-FM2 WSM10S Manufacturer: Walter Tools Product type: Indexable turning insert Form: Rhombus 55° Size: 11 Thickness: T3 Clearance angle: 7° Corner radius: 0.2 mm Chipbreaker: FM2 Series: Tiger·tec Silver Grade: WSM10S Tolerance class: G Material group suitability: S / M Facts Insert size: 11 Corner radius: 0.2 mm Clearance angle: 7° Thickness designation: T3 Tolerance: G Special features Coated cemented carbide (Tiger·tec Silver) Designed for stainless steels (ISO M) Suitable for heat‑resistant alloys and titanium (ISO S) FM2 chipbreaker for controlled chips Compact Rhombus 55° geometry for versatile turning FAQ What materials is this insert best suited for? The DCGT11T302-FM2 WSM10S insert is designed primarily for stainless steels (ISO group M) and heat‑resistant alloys or titanium (ISO group S), where thermal resistance and edge stability are required. How does the Tiger·tec Silver technology benefit cutting performance? Tiger·tec Silver provides a coated surface and wear‑resistant substrate that reduce flank and crater wear on the DCGT11T302-FM2 WSM10S, enabling longer tool life and consistent surface quality in serial machining. Which chip control behaviour can be expected with the FM2 chipbreaker? The FM2 chipbreaker on this insert produces short, controllable chips under typical turning conditions, improving chip evacuation and reducing the risk of workpiece or tool damage. Is the DCGT11T302-FM2 compatible with standard DCGT tool holders? Yes, the DCGT form factor matches standard tool holders designed for DCGT inserts; verify seat and clamping specifications for secure mounting and optimal cutting geometry. What production advantages does this insert provide for serial operations? The combination of the WSM10S grade and robust geometry supports higher process stability, fewer insert changes and more predictable batch quality, which enhances overall productivity. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCGT11T302-FM2 WSM20S FM2 Wendeplatten - Walter Tools
Take advantage of the combination of WSM20S grade and Tiger·tec Silver coating for secure chip control and extended edge life when machining stainless steels and superalloys; order the DCGT11T302-FM2 WSM20S turning insert via Metav Werkzeuge or consult our specialists for application advice. DCGT11T302-FM2 – Indexable turning insert DCGT11T302-FM2 WSM20S for stainless steel and superalloys by Walter Tools The DCGT11T302-FM2 WSM20S is a coated carbide turning insert engineered for secure chip control and reliable performance when machining stainless steels and heat‑resistant superalloys. Tiger·tec Silver coated carbide grade WSM20S Optimised FM2 chipbreaker for stable chip control Rhombic 55° shape with r0.2 corner radius 7° clearance angle; thickness T3, tolerance G High‑performance grade for demanding materials The combination of the WSM20S grade and Tiger·tec Silver technology delivers a coated carbide solution tailored to stubborn materials. Designed for ISO groups M and S, the grade supports machining of stainless steels and heat‑resistant superalloys by offering improved thermal resistance and edge stability. The result is fewer interruptions for tool changes and a more consistent production rhythm, contributing to measurable productivity gains in serial turning operations. Precision geometry for consistent surface quality The insert’s Rhombic 55° geometry, combined with a r0.2 corner radius and 7° clearance, provides a balance between strength and cutting precision. This geometry enables controlled engagement during light finishing passes while maintaining tool life for semi‑finishing. The T3 plate thickness and tolerance G support repeatable seating and minimal setup deviation, translating to reliable dimensional accuracy and improved surface finishes on turned components. Stable chip formation and process security An optimised FM2 chipbreaker promotes secure chip formation across a range of cutting conditions, reducing the risk of built‑up edge and improving evacuation in continuous turning. The coating and substrate pairing emphasise process security, helping to maintain a stable cutting edge even under elevated temperatures that occur with difficult‑to‑machine alloys. For production shops seeking consistent cycle times and fewer rejects, this insert contributes to reduced overall machining costs through longer effective tool life and predictable performance. Contact Metav Werkzeuge for application recommendations and current availability on the Walter Tools DCGT11T302-FM2 WSM20S insert at info@metav-werkzeuge.com or +49 2822 7131930; specialists are available to advise on tooling strategies and batch supply Technical data Article number/SKU: DCGT11T302-FM2-WSM20S-WALTER Product type: Indexable turning insert Designation: DCGT11T302-FM2 WSM20S Facts Shape: Rhombic 55° Corner radius: r0.2 Clearance angle: 7° Thickness: T3 Size: 11 Tolerance class: G Special features Grade: WSM20S (Tiger·tec Silver) Coating/substrate: coated carbide Chipbreaker: FM2 Suitable for: stainless steel (ISO M), heat‑resistant superalloys and titanium (ISO S) Execution: T FAQ What materials is this insert suitable for? The DCGT11T302-FM2 WSM20S insert is specified for stainless steels (ISO M) and heat‑resistant superalloys and titanium (ISO S), reflecting the thermal and mechanical demands of these groups. What is the benefit of the Tiger·tec Silver grade? Tiger·tec Silver in the WSM20S grade provides enhanced thermal stability and wear resistance, extending edge life and improving consistency when machining demanding materials. What geometry and key dimensions does the insert offer? The insert features a Rhombic 55° form with r0.2 corner radius, 7° clearance, thickness T3, size 11 and tolerance G, enabling precise seating and repeatable results. How does the FM2 chipbreaker affect performance? The FM2 chipbreaker is optimised for controlled chip formation and evacuation, reducing built‑up edge and promoting stable cutting conditions in continuous turning processes. Is this insert suited for finishing operations? Yes—the combination of rhombic geometry and a small corner radius supports fine finishing passes while maintaining adequate edge strength for productive usage. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only and do not indicate any partnership or affiliation. The offered item is original, brand‑new goods from the manufacturer.
DCGT11T302-FN2 WN10 WN10 Wendeplatten - Walter Tools
Take advantage of consistent chip control and the precision geometry of this Walter Tools turning insert for reliable process stability in serial machining; check the product matrix for material suitability and order via Metav Werkzeuge or consult our technical team for selection support. DCGT11T302-FN2 WN10 — Indexable turning insert, rhombic 55°, FN2 chipbreaker (Walter Tools) The DCGT11T302-FN2 WN10 is an indexable turning insert designed for precision turning operations where repeatable chip control and edge stability are required Uncoated carbide grade WN10 Rhombic 55° geometry for versatile tool access FN2 chipbreaker for controlled chip formation 7° relief angle for secure cutting engagement 0.2 mm corner radius for fine finishing Reliable chip control for steady production The FN2 chipbreaker is engineered to promote stable chip formation, reducing risk of entanglement and interruptions on the production floor. By combining the chipbreaker with an uncoated carbide grade, the insert delivers predictable cutting behaviour that supports consistent cycle times. For process engineers this translates into fewer unscheduled stops and improved machine utilisation. Check the product matrix for specific workpiece compatibility before final selection to ensure optimal performance. Geometry tuned for precision and accessibility The rhombic 55° geometry and 7° relief angle enable secure cutting engagement while allowing access to profiles and interrupted cuts often encountered in turning operations. The small 0.2 mm corner radius offers a balance between edge strength and surface quality, making the insert suitable where dimensional accuracy and finish are priorities. Tooling setups benefit from the insert’s compact form, which supports tight radii and detailed contours with reliable repeatability. Uncoated carbide grade for consistent edge behaviour The WN10 designation denotes an uncoated cemented carbide composition known for its consistent edge geometry and ease of regrinding if required. Uncoated grades can be preferable where coating adhesion is a concern or where a sharp, well-defined cutting edge is needed for finishing passes. Material suitability should be verified using the manufacturer’s application matrix to match the insert to the correct workpiece material and cutting parameters. Production advantages: tolerance, series and handling Delivered in tolerance class G and produced as part of the Walter Schneidstoffsorte series, the insert supports standardised changeovers and predictable dimensional conformity. The T3 thickness and standard form factor simplify toolholder selection and inventory management, improving process control across batches. When paired with appropriate cutting data, this insert can contribute to steady tool life and fewer interventions, helping to streamline shopfloor operations and quality assurance. Discuss the Walter Tools DCGT11T302-FN2 WN10 with Metav Werkzeuge for application-specific recommendations and process optimisation — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: DCGT11T302-FN2-WN10-WALTER Label: Drehwendeschneidplatte DCGT11T302-FN2 WN10 Walter Tools Product type: Indexable turning insert Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Grade/Sorte: WN10 Key dimensions Insert size: 11 Shape: Rhombus 55° Thickness: T3 Relief angle: 7° Corner radius: 0.2 mm Materials & features Coating: uncoated (cemented carbide) Chipbreaker: FN2 Tolerance class: G Execution: T Note: Verify material suitability in the product matrix FAQ What types of machining is this insert suited for? The DCGT11T302-FN2 WN10 indexable turning insert by Walter Tools is intended for turning operations requiring controlled chips and precise edge behaviour; consult the product matrix for specific workpiece-material recommendations. Can the insert be reground or reused? The uncoated WN10 grade is compatible with regrinding practices typical for cemented carbide inserts; follow Walter Tools’ guidelines for maximum number of regrinds and cutting-edge dimensions. What does the FN2 chipbreaker offer compared with other breakers? The FN2 chipbreaker on this insert promotes stable chip formation and reduced chip stringing, which improves process stability and lowers the likelihood of machine interruptions. How does the 0.2 mm corner radius affect surface finish? A 0.2 mm corner radius provides a compromise between edge strength and surface quality, supporting fine finishing passes with good dimensional control when correct cutting parameters are applied. What does tolerance class G mean for production? Tolerance class G indicates standardised dimensional conformity for the insert, supporting predictable interchangeability and simplified quality checks in production environments. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCGT11T302-FN2 WNN10 Wendeplatten - Walter Tools
Take advantage of the combination of productive chip control and consistent tool life from a coated-carbide insert designed for general turning. The robust WNN10 grade together with the FN2 chipbreaker and 55° rhombic geometry ensures efficient material removal and stable cutting conditions; order directly via Metav Werkzeuge or consult their technical team for application support. DCGT11T302-FN2 WNN10 – Turning insert, rhombic 55° (Walter Tools) The DCGT11T302-FN2 WNN10 is a coated-carbide turning insert engineered for versatile external and light internal turning, offering a 55° rhombic geometry and a controlled-chip FN2 breaker for reliable swarf management Coated carbide grade WNN10 FN2 chipbreaker for stable chip flow Rhombic 55° geometry for versatile turning Consistent productivity through material and coating technology The insert is produced in the WNN10 coated-carbide grade, a choice that balances wear resistance and cost-effectiveness for a broad range of turning tasks. The coating reduces abrasive wear and helps maintain a sharp cutting edge over longer runs, which translates into fewer tool changes and improved uptime. The combination of a heat-resistant coating and a substrate designed for general turning yields predictable performance when machining a variety of steels and similar materials. This makes the component particularly suitable where cycle-time reduction and repeatable results are required. Geometry and small radii for precise surface control A rhombic 55° shape with a 0.2 mm corner radius supports both profile and finishing operations with good access in turning applications. The 55° approach angle provides a compromise between cutting-edge strength and the ability to produce narrow shoulders or interrupted cuts, while the small radius helps achieve finer surface finishes without excessive cutting forces. The T3 thickness offers a compact cutting edge geometry that suits light to medium cutting depths, helping to maintain dimensional accuracy and consistent surface quality on turned parts. Chip control and operational stability for reliable series production Built with the FN2 chipbreaker, the insert is optimised for stable chip formation across varying feed rates. Controlled chip breaking reduces the risk of long swarf strands that can tangle with the workpiece or toolholder, supporting safer and cleaner machining cycles. The DCGT11T302-FN2 WNN10 insert's profile and chip control features help to reduce secondary operations and machine downtime, delivering measurable efficiency gains in repetitive turning tasks. Where process reliability is essential, this solution offers a pragmatic balance of durability and chip management. Contact Metav Werkzeuge today for tailored application advice or to discuss toolholder compatibility and cutting parameters for this Walter Tools turning insert; phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: DCGT11T302-FN2-WNN10-WALTER Article designation: DCGT11T302-FN2 ISO designation: DCGT11T302-FN2 WNN10 Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Facts Clearance angle: 7° Corner radius: 0.2 mm Insert size: 11 Thickness code: T3 Tolerance class: G Special features Coating: coated carbide (WNN10) Chipbreaker: FN2 Plate form: Rhombus 55° Execution: T Material designation: catalogue dependent FAQ What applications is this insert suited for? The DCGT11T302-FN2 WNN10 turning insert is intended for general turning operations where controlled chip formation and a versatile rhombic geometry are required, covering many steel turning tasks when used with appropriate parameters. How does the FN2 chipbreaker affect machining? The FN2 chipbreaker on this Walter Tools insert produces short, manageable chips that improve process stability and reduce swarf-related interruptions during continuous and semi-continuous turning. Can the insert achieve fine surface finishes? Yes; the 55° rhombic geometry combined with the 0.2 mm corner radius supports improved surface quality in finishing passes while maintaining adequate edge strength for light- to medium-duty cuts. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCGT11T302-MM4 WSM01 WSM01 Wendeplatten - Walter Tools
Take advantage of the combination of precise geometry, secure chip control and a heat‑resistant coated carbide grade for consistent turning of stainless steels and superalloys; order the insert directly via Metav Werkzeuge or consult our specialists for application‑specific cutting data. DCGT11T302-MM4 WSM01 – Turning indexable insert with Rhombic 55° geometry, Tiger‑tec Silver The DCGT11T302-MM4 WSM01 is a rhombic 55° indexable turning insert engineered for heavy‑duty machining of stainless steels and heat‑resistant superalloys, offering a balance of chip control and cutting‑edge stability for demanding turning operations Tiger‑tec Silver coating technology Designed for stainless and superalloys Rhombic 55° geometry, 0.2 mm corner MM4 chipbreaker for secure chip control Increased productivity with reliable material coverage The combination of the Tiger‑tec Silver series and the WSM01 grade provides a coated carbide solution optimised for difficult‑to‑machine materials. Designed to tackle both stainless steels and heat‑resistant superalloys, this insert supports repeatable metal removal by improving cutting‑edge stability and reducing unexpected tool changes. The hardened coating and substrate pairing reduce wear when temperatures rise at the cutting zone, which translates into longer periods between tool changes and a steadier production flow. Where cycle time and component quality matter, the insert’s specification offers measurable process gains. Geometry and chip management that protect surface finish The Rhombic 55° shape with a 0.2 mm corner radius and a 7° clearance angle creates a cutting geometry that balances robustness and finesse. The MM4 chipbreaker is designed to form and control chips efficiently during interrupted cuts and continuous turning alike; this reduces the risk of chip entanglement and improves surface quality. For operators less familiar with chip morphology, the chipbreaker helps generate short, manageable chips instead of long, stringy ones, reducing manual intervention and increasing machine uptime while preserving the required workpiece finish. Durable performance and economical tool life Built to meet industrial tolerance class G and supplied in a compact 11 mm format with T3 thickness, the insert is engineered for stable clamping in standard toolholders and predictable wear progression. The WSM01 grade, a coated carbide, is tailored for the thermal and mechanical stresses of high‑temperature alloys and stainless materials, offering consistent edge retention and reduced notch wear. This combination lowers total cost of ownership through fewer insert changes and more predictable regrinding or replacement intervals, supporting continuous, efficient production in high‑mix and high‑volume turning operations. Contact Metav Werkzeuge for tailored cutting data and application advice on Walter Tools Tiger‑tec Silver inserts and receive specific recommendations for cycle speeds and feeds. Technical data Article number: DCGT11T302-MM4-WSM01-WALTER Designation: DCGT11T302-MM4 WSM01 Product type: Turning indexable insert Manufacturer: Walter Tools Facts Size: 11 mm Thickness: T3 Clearance angle: 7° Corner radius: 0.2 mm Geometry: Rhombic 55° Tolerance class: G Special features Series: Tiger‑tec Silver Grade: WSM01 (coated carbide) Chipbreaker: MM4 Suitable materials: stainless steels; heat‑resistant superalloys FAQ What materials is this insert best suited for? The DCGT11T302-MM4 WSM01 insert is formulated for stainless steels and heat‑resistant superalloys, benefitting from the Tiger‑tec Silver coating and WSM01 grade for secure chip formation. How does the MM4 chipbreaker affect machining? The MM4 chipbreaker on the DCGT11T302-MM4 supports controlled chip formation, producing short chips in both continuous and interrupted turning to protect the workpiece finish and machine tooling. What does the 0.2 mm corner radius mean for component finish? A 0.2 mm corner radius on the insert helps balance edge strength and surface quality; the small radius reduces cutting forces while still providing sufficient edge robustness for most turning tasks. Is this insert suitable for high‑temperature alloy work? Yes, the WSM01 grade and Tiger‑tec Silver series are designed for applications involving heat‑resistant superalloys where thermal stability and edge retention are critical. Which tolerance class is specified and why does it matter? The insert conforms to tolerance class G, ensuring consistent dimensions for secure seating in toolholders and predictable machining results across production batches. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product from the manufacturer.
DCGT11T302-MM4 WSM20S MM4 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WSM20S grade and a precise MM4 chipbreaker for reliable performance in stainless steel and heat-resistant alloys; order the DCGT11T302-MM4 WSM20S insert from Metav Werkzeuge or consult the technical team for tailored cutting data. DCGT11T302-MM4 WSM20S turning indexable insert by Walter Tools — Tiger·tec Silver, MM4 chipbreaker The DCGT11T302-MM4 WSM20S is a rhombic 55° turning insert designed for demanding operations in stainless steel and high-temperature alloys. Tiger·tec Silver coated carbide for longer life Grade WSM20S optimised for tough alloys MM4 chipbreaker for controlled chip formation Rhombus 55° geometry for versatile turning Precision coating for consistent production results The combination of the Tiger·tec Silver coating and the WSM20S carbide grade delivers a balance of wear resistance and edge security that supports stable chip formation in difficult-to-cut materials. The advanced coating reduces flank wear and helps maintain cutting-edge integrity during interrupted cuts and heavy engagement. For production environments where downtime and rework are costly, this insert contributes to process stability and predictable tool change intervals. Controlled chips and surface quality through geometry and edge design The MM4 chipbreaker and a 0.2 mm corner radius work together to moderate chip flow and minimise built-up edge, which is particularly beneficial when machining stainless steel or Inconel-type alloys. The rhombic 55° shape and a 7° clearance angle provide an effective balance between strength and accessibility, producing improved surface finishes and reducing the need for secondary operations. This geometry helps sustain cutting pressures within safe limits and supports repeatable component quality. Flexible integration with standard turning toolholders With an insert size of 11 and thickness T3, the design is suitable for a wide range of conventional turning toolholders and makes retrofitting into existing toolsets straightforward. The coated carbide substrate and the MM4 chip control make the solution a practical choice for batch production or mixed-series machining where stainless steel is a frequent workpiece material. For precise cutting parameters or application-specific recommendations, Metav Werkzeuge provides cutting data and support to align machining conditions with component tolerances and cycle-time goals. Contact Metav Werkzeuge for application advice, cutting data sheets or a tailored quotation for Walter Tools DCGT11T302-MM4 WSM20S inserts Technical data Article number: DCGT11T302-MM4-WSM20S-WALTER Designation: DCGT11T302-MM4 Series: Tiger·tec Silver Grade: WSM20S Manufacturer: Walter Tools Product type: Turning indexable insert Numbers / Facts Insert size: 11 Corner radius: 0.2 mm Clearance angle: 7° Thickness: T3 Tolerance class: G Special features / Versions Coating: Tiger·tec Silver Carbide type: Coated hardmetal (coated carbide) Chipbreaker: MM4 Geometry: Rhombus 55° Material suitability: stainless steel, heat-resistant superalloys and titanium Series note: Optimised for heavy-duty and high-temperature applications FAQ Is this insert suitable for stainless steel? Yes. The DCGT11T302-MM4 WSM20S insert with Tiger·tec Silver coating and MM4 chipbreaker is specifically designed to perform well in stainless steel, supporting secure chip formation and edge stability. Which materials beyond stainless steel can this grade machine? The WSM20S grade and coated substrate are suitable for heat-resistant superalloys and certain titanium applications, offering thermal stability and wear resistance under difficult cutting conditions. What are the advantages of the MM4 chipbreaker on this insert? The MM4 chipbreaker provides consistent chip control and reduces the risk of built-up edge, which improves surface finish and extends the interval between tool changes when machining tough alloys. Can the DCGT11T302-MM4 be used in standard toolholders? Yes. The insert’s size and T3 thickness are compatible with common turning toolholders, enabling straightforward integration into existing tool setups for production or prototyping. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCGT11T302-MN2 WN10 Wendeplatten - Walter Tools
Take advantage of a robust combination of WN10 uncoated cemented carbide and a precise MN2 chipbreaker to secure stable chip formation and consistent machining results; the rhombic 55° geometry with a 0.2 mm corner radius supports fine surface finishes while the 7° clearance angle reduces rubbing. Order the DCGT11T302-MN2 WN10 insert directly via Metav Werkzeuge or consult their specialists for application-specific setup. DCGT11T302-MN2 WN10 Rhombic 55° Turning Insert by Walter Tools — 0.2 mm corner radius, MN2 chipbreaker DCGT11T302-MN2 WN10 is an indexable turning insert designed for general turning tasks where predictable chip control and repeatable edge performance are required Uncoated carbide grade WN10 Rhombic 55° geometry for versatile turning 0.2 mm corner radius for fine finishes MN2 chipbreaker for controlled chip formation Reliable chip control for steady productivity The combination of an MN2 chipbreaker and an uncoated cemented carbide WN10 grade provides reliable chip formation across a range of common turning operations. The chipbreaker design supports consistent evacuation and reduces the risk of chip-related interruptions, which contributes to improved cycle times and fewer reworks. For process planners and shop floor engineers, this means a predictable cutting behaviour that aids parameter optimisation and shortens setup times. Geometry tuned for surface quality and tool life A rhombic 55° insert shape paired with a 0.2 mm corner radius and a 7° clearance angle delivers a balance between accessibility and finish quality. The modest corner radius is suited to fine to medium finishing passes where controlled cutting forces help achieve improved surface integrity. The insert’s tolerance class G ensures consistent fit in standard toolholders, supporting repeatable edge positioning and facilitating economical index changes during production runs. Practical selection and application guidance The insert is supplied in a T3 thickness format and a nominal size 11, making it compatible with many common turning tool systems; the uncoated nature of the WN10 grade should be matched to workpiece materials by consulting the product matrix. The series is listed as Walter Schneidstoffsorte - Serie offen, and material data are catalogue-dependent, so checking the exact material recommendations for specific steels or alloys will support optimal cutting speeds and feeds. The clearly stated geometry and chipbreaker help machinists choose suitable cutting parameters for stable, reproducible results. For machining situations that prioritise predictable chip behaviour with a no-coating carbide grade, contact Metav Werkzeuge to discuss the Walter Tools inserts and receive tailored parameter advice via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: DCGT11T302-MN2-WN10-WALTER Designation: DCGT11T302-MN2 WN10 Series: Walter Schneidstoffsorte - Serie offen Grade: WN10 Geometry: Rhombus 55° Size: 11 Thickness: T3 Corner radius: 0.2 mm Clearance angle: 7° Chipbreaker: MN2 Tolerance class: G Material: Katalogabhängig Core specifications Size: 11 mm Corner radius: 0.2 mm Clearance angle: 7° Thickness code: T3 Tolerance: G Materials & special features Uncoated cemented carbide (WN10) MN2 chipbreaker for controlled chips Rhombic 55° plate form for versatile turning Series designation indicates open product range Application: turning (indexable insert) FAQ What materials is this insert suitable for? Material suitability for the DCGT11T302-MN2 WN10 insert should be checked against the manufacturer’s product matrix; WN10 is an uncoated cemented carbide grade and general recommendations are available from Walter Tools documentation How does the MN2 chipbreaker affect performance? The MN2 chipbreaker on the DCGT11T302-MN2 WN10 promotes controlled chip formation and evacuation, which improves process stability and reduces the likelihood of chip interference during turning operations What does the designation DCGT11T302-MN2 WN10 mean? The designation describes a rhombic 55° indexable insert (DCGT), with nominal size 11 and thickness code T3, a 0.2 mm corner radius, MN2 chipbreaker and the WN10 uncoated carbide grade from Walter Tools (SKU DCGT11T302-MN2-WN10-WALTER) Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is original and brand-new from the manufacturer.
DCGT11T302-MN2 WNN10 Wendeplatten - Walter Tools
Combining the WNN10 coated-carbide grade with the MN2 chipbreaker and a 55° rhombic geometry delivers consistent chip control and long tool life for versatile turning operations; order directly via Metav Werkzeuge or consult their specialists for application-specific configuration. DCGT11T302-MN2 WNN10 – indexable turning insert, MN2 chipbreaker, rhombic 55° by Walter Tools The DCGT11T302-MN2 WNN10 is an indexable turning insert optimised for general turning, offering reliable chip control through the MN2 breaker and a compact rhombic 55° form for versatile approach angles. Coated carbide grade WNN10 MN2 chipbreaker for predictable chips Rhombic 55° geometry for versatile turning 0.2 mm corner radius for improved finishes Improved process efficiency with controlled chip formation The combination of a coated carbide cutting material and the MN2 chipbreaker focuses on stability and productivity. Coated carbide provides a wear-resistant cutting edge that extends tool life under typical turning conditions, while the MN2 chip control geometry reduces interruptions from irregular chips. This configuration supports a smoother machining cycle and fewer tool changes, which translates into measurable time savings on the shop floor. For operations where consistent metal removal rates are essential, the insert's design contributes to predictable chip control and reduced downtime. Geometry and edge detail that support surface quality The rhombic 55° insert shape with a corner radius of 0.2 mm and T3 thickness balances accessibility with surface finish requirements. The 55° approach angle allows secure positioning in standard tool holders and helps maintain consistent cutting forces during finishing passes. A modest corner radius provides a fine surface texture without sacrificing edge strength, while the insert thickness supports stable clamping and heat resistance. The specified tolerance class G indicates consistent dimensional accuracy, which is important for repeatable part quality in serial production. Selection guidance and application notes for reliable results This insert belongs to the Walter Schneidstoffsorte - Serie offen and is a coated carbide (WNN10) grade; material suitability should be verified against the manufacturer's product matrix before selecting cutting parameters. The insert is best applied in general turning tasks where medium to fine surface qualities are required. For unfamiliar workpiece materials or unusual process conditions, consult the technical information matrix to match grade and geometry to the substrate and cutting data. The insert's compact form and chipbreaker make it a practical choice when stable chip evacuation and consistent tool life are priorities. For tailored recommendations on using Walter Tools' WNN10 grade and the MN2 chipbreaker, contact Metav Werkzeuge for details and order support at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: DCGT11T302-MN2-WNN10-WALTER ISO designation: DCGT11T302-MN2 WNN10 Series: Walter Schneidstoffsorte - Serie offen Manufacturer: Walter Tools Numbers / Core technical data Insert size: 11 Thickness: T3 Corner radius: 0.2 mm Relief / free angle: 7° Insert form: Rhombus 55° Tolerance class: G Designs / Special features Chipbreaker: MN2 Material: Coated carbide (WNN10) Execution: T Application note: Check product matrix for material suitability FAQ What materials is this insert suitable for? Material suitability depends on the product matrix; the DCGT11T302-MN2 WNN10 is a coated carbide grade intended for a broad range of turning applications, but specific substrates should be confirmed against the manufacturer's recommendations. How does the MN2 chipbreaker affect performance? The MN2 chipbreaker promotes predictable chip shapes and improved evacuation, which supports continuous machining and reduces interruptions during turning operations with this insert. What surface finish can be expected with a 0.2 mm corner radius? A 0.2 mm corner radius helps achieve finer surface finishes while maintaining edge strength; the exact result depends on cutting conditions and workpiece material. Is the insert compatible with standard indexable tool holders? The rhombic 55° form and T3 thickness are designed for compatibility with common indexable turning holders that accept DCGT-style inserts. Where can one find cutting data and grade selection charts? Refer to the manufacturer's technical information and product matrix for cutting data, grade comparisons and recommended parameters for the DCGT11T302-MN2 WNN10 insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Mention of brand names such as Walter Tools is for explanatory purposes only and does not imply any affiliation with or endorsement by those trademark holders. The described article is offered as original, new factory products of the respective manufacturer.
DCGT11T302-MN2 WSM01 MN2 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating and the WSM01 grade for stable chip formation and extended tool life when machining stainless steel and high‑temperature alloys; order the insert directly via Metav Werkzeuge or request consultancy for optimised process integration. DCGT11T302-MN2 WSM01 indexable turning insert — Walter Tools, Tiger‑tec Silver, for stainless steel and superalloys A DCGT11T302-MN2 WSM01 indexable turning insert engineered to ensure reliable cutting performance in stainless steel and heat‑resistant superalloys under continuous production conditions Tiger‑tec Silver coating for thermal stability WSM01 grade for stainless steel and superalloys Rhombic 55° shape with 0.2 mm corner radius 7° clearance angle and T3 plate thickness Consistent cutting performance in demanding alloys The combination of the Tiger‑tec Silver series and the WSM01 carbide grade delivers a well‑balanced solution for machining stainless steel and heat‑resistant superalloys. The coating improves heat resistance and reduces flank wear, which in turn supports stable chip formation and prolongs tool life. For production environments where tool change frequency impacts throughput, this specification contributes directly to higher process efficiency and predictable results. Geometry that supports surface quality and repeatability A rhombic 55° profile with a 0.2 mm corner radius and a dedicated MN2 chipbreaker produces controlled chip flow and consistent contact conditions at the cutting edge. The modest 7° clearance angle and T3 plate thickness optimise engagement and mechanical rigidity, reducing vibration and improving surface finish. In practical terms, these geometrical choices reduce the need for rework and support tighter dimensional tolerances on turned components. Productivity gains and economic advantages Designed for continuous turning operations, the insert’s thermal resilience and edge stability reduce unplanned downtime and raise the achievable material removal rates. The robust cutting edge behaviour of the specified grade lowers the risk of built‑up edge on tough materials and supports higher cutting speeds where process conditions allow. These attributes translate into lower cost‑per‑part and improved overall equipment effectiveness in serial machining. Application guidance and selection notes The insert suits applications where stainless steel and other hard‑to‑cut alloys must be machined reliably; selection of feed and speed should reflect the component geometry and machine capability. The MN2 chipbreaker performs best in medium to heavy cuts where consistent chip control is required. Operators with limited experience in superalloy turning will benefit from process parameter suggestions and trial cuts to establish the most economical window for production. For tailored advice on integrating Walter Tools Tiger‑tec Silver inserts into production, contact Metav Werkzeuge for process consultation and availability — info@metav-werkzeuge.com • +49 2822 7131930. Technical Data Article number: DCGT11T302-MN2-WSM01-WALTER Label: Drehwendeschneidplatte DCGT11T302-MN2 WSM01 Walter Tools Manufacturer: Walter Tools Facts Corner radius: 0.2 mm Clearance angle: 7° Plate form: Rhombus 55° Plate size: 11 Plate thickness: T3 Tolerance class: G Special features Series: Tiger‑tec Silver Grade: WSM01 (coated carbide) Chipbreaker: MN2 Applicable materials: stainless steel (M), heat‑resistant superalloys/titanium (S) Execution: T FAQ What materials is this insert suitable for? The DCGT11T302-MN2 WSM01 insert is specified for stainless steel and heat‑resistant superalloys; the WSM01 grade supports secure chip formation and a stable cutting edge in these groups. How does the Tiger‑tec Silver series affect machining? The Tiger‑tec Silver coating increases thermal resistance and wear protection, enabling higher cutting speeds and longer tool life when using the Walter Tools turning insert. What does the MN2 chipbreaker provide? The MN2 chipbreaker is designed for reliable chip control in medium to heavy cutting conditions, reducing the likelihood of chip interference and improving surface consistency. Which geometry features improve surface finish? A rhombic 55° profile combined with a 0.2 mm corner radius and 7° clearance angle delivers reduced vibration and consistent contact, which supports improved surface quality and dimensional repeatability. Is this insert suitable for serial production? Yes — the grade and coating combination of this insert is optimised for process stability and extended tool life, making it well suited to serial turning of stainless steel and similar alloys. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany; Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
DCGT11T302FS-1 WDN10 WDN10 Wendeplatten - Walter Tools
Take advantage of the WDN10 polycrystalline diamond grade and precise Rhombic 55° geometry to extend tool life and ensure consistent turning performance; order this insert directly via Metav Werkzeuge or consult our technical advisors for application-specific guidance. DCGT11T302FS-1 WDN10 indexable turning insert by Walter Tools — PCD grade for abrasive non‑ferrous materials DCGT11T302FS-1 WDN10 is an indexable turning insert designed for high‑wear applications in non‑ferrous and abrasive, non‑iron materials, offering long tool life and consistent chip control Walter Tools PCD grade WDN10 Rhombic 55° insert geometry 0.2 mm corner radius for fine detail Free cutting angle 7° for reliable engagement Longer production runs through superior wear resistance The polycrystalline diamond (PCD) composition of this insert, specified as WDN10, delivers markedly improved wear resistance compared with conventional carbide grades. That resistance translates directly into longer stand‑times, fewer insert changes and less unplanned downtime — a clear advantage for batch production and serial machining of abrasive non‑ferrous parts. The economic effect is tangible: reduced tool consumption and greater uptime, which supports a smoother production flow and predictable throughput. Consistent component accuracy from optimised geometry The Rhombic 55° shape combined with a 0.2 mm corner radius and a 7° free cutting angle provides stable insert seating and predictable cutting forces. This geometry reduces vibration and supports repeatable dimensional results on turned components, especially where fine edge definition is required. The insert’s T3 thickness contributes to rigidity in the toolholder, improving surface finish and maintaining tolerance adherence across extended cycles. Tailored for abrasive, non‑ferrous materials — clear machining benefits Designed specifically for abrasive, non‑iron materials, the cutting grade excels on components such as abrasive aluminium alloys and other non‑ferrous, particle‑laden workpieces. The PCD cutting edge sustains sharpness in conditions that would rapidly wear carbide, enabling higher cut volumes before replacement. It is advisable to check the specific product matrix for workpiece compatibility to ensure optimal performance and to match cutting data to material characteristics. Easy integration and reliable specification for production planning Marked as DCGT11T302FS-1 and manufactured to tolerance class G, this indexable insert fits standard turning toolholders that accept the DCGT format. The clearly defined dimensions and chipbreaker designation support predictable chip formation and evacuation, helping to avoid rework and improving cycle consistency. For tailored cutting data and confirmation of toolholder compatibility, consult the Metav Werkzeuge technical team to align insert choice with production goals. Contact Metav Werkzeuge for a technical assessment of Walter Tools inserts and to request an application‑specific recommendation for DCGT11T302FS-1 WDN10 Technical data SKU: DCGT11T302FS-1-WDN10-WALTER Designation: DCGT11T302FS-1 WDN10 Type: Indexable turning insert Manufacturer: Walter Tools Grade: WDN10 (PCD) Series: Walter Schneidstoffsorte - Serie offen Facts Insert form: Rhombus 55° Corner radius: 0.2 mm Free cutting angle: 7° Insert size: 11 Thickness: T3 Chipbreaker: 1 Tolerance class: G Special features Material: Katalogabhängig High wear resistance due to PCD cutting edge Intended use: abrasive, non‑ferrous materials (verify product matrix) Stable chip control and consistent surface quality Suitable for production runs requiring long tool life FAQ What materials is this insert best suited for? The DCGT11T302FS-1 WDN10 insert employs a PCD grade that is particularly suited to abrasive, non‑ferrous materials; check the product matrix to confirm compatibility with specific alloys. How does the WDN10 grade affect tool life compared with carbide? WDN10’s polycrystalline diamond composition provides significantly higher wear resistance than typical carbide grades, resulting in longer stand‑times and fewer insert changes in abrasive non‑ferrous applications. Is the DCGT11T302FS-1 compatible with standard DCGT toolholders? Yes, the insert conforms to DCGT geometries and fits holders designed for Rhombus 55° DCGT inserts; confirm holder clamping specifications and tolerance class G for best results. Where can machining parameters for this Walter Tools insert be obtained? Cutting data and recommended parameters can be provided by Metav Werkzeuge; consult with their technical advisors to match feed, speed and depth of cut to the specific workpiece and process. Protected trademarks and trade names are mentioned for explanatory purposes only. The use of brand names and protected designations does not imply any affiliation or endorsement by the named manufacturers. The offered item is an original, factory‑new product of the respective manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
DCGT11T302M-FP2 WEP10C WEP10C Wendeplatten - Walter Tools
Take advantage of the combination of precise geometry, stable chip control and the wear-resistant WEP10C cermet grade for consistent finishing results; order the DCGT11T302M-FP2 WEP10C turning insert directly via Metav Werkzeuge or consult our advisors for application guidance. DCGT11T302M-FP2 WEP10C — Turning insert (Rhombus 55°, FP2) by Walter Tools A DCGT11T302M-FP2 WEP10C turning insert engineered for finishing and medium-duty turning, featuring a Rhombus 55° shape with a 0.2 mm corner radius and FP2 chip control for reliable machining. Walter Cermet grade WEP10C Rhombus 55° insert geometry FP2 chipbreaker for stable chip control 7° clearance angle, 0.2 mm corner radius Consistent surface quality through optimised geometry The combination of a Rhombus 55° form and a 0.2 mm corner radius is designed to deliver repeatable surface finishes while maintaining dimensional control in finishing passes. The modest clearance angle of 7° reduces rubbing and helps to keep cutting forces stable, which supports lower vibration and better tool life. These geometric details translate into fewer rework cycles and improved process reliability when used with appropriate holders and cutting parameters. Cermet grade WEP10C: precision and wear resistance Built on the Walter Cermet series, the WEP10C grade offers the characteristics typical of cermet cutters: enhanced hardness at cutting temperatures and a strong resistance to abrasive wear. That combination benefits finishing operations where surface integrity and consistent tool life are required. Material suitability should be verified in the manufacturer's application matrix, since cutting performance depends on workpiece material, cooling strategy and feed/speed selection. FP2 chipbreaker and its role in process stability The FP2 chipbreaker is tailored for controlled chip formation in light to medium cutting conditions, promoting steady chip flow and minimising entanglement. Controlled chips reduce the risk of tool damage and contribute to a safer machining environment. Together with the insert's production tolerance class G and its T3 thickness, the result is a predictable, indexable component that supports efficient tool changes and repeatable machining results. System compatibility and handling that speed operations The ISO-style designation indicates compatibility with standard DCGT11 indexable tool holders, permitting quick indexing and secure clamping. The insert's size and format simplify inventory management within indexable-tool systems and streamline set-up times on the shop floor. For complex applications or when material data is uncertain, the manufacturer's matrix and a short process trial will help determine optimal cutting parameters and confirm the insert's suitability. For precision finishing with the durability of a cermet solution, contact Metav Werkzeuge for technical advice on the Walter Cermet DCGT11T302M-FP2 WEP10C insert — technical consultants are available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: DCGT11T302M-FP2-WEP10C-WALTER Label: Drehwendeschneidplatte DCGT11T302M-FP2 WEP10C Walter Tools Manufacturer: Walter Tools Facts Insert size: 11 Thickness: T3 Clearance angle: 7° Corner radius: 0.2 mm Shape: Rhombus 55° Tolerance class: G Special features Series: Walter Cermet Grade: WEP10C (cermet) Chipbreaker: FP2 Execution: T ISO designation: DCGT11T302M-FP2 WEP10C Material information: Katalogabhängig FAQ Which materials is this cermet grade suitable for? The WEP10C cermet grade is intended for precision finishing; exact workpiece suitability should be checked in the manufacturer's material and application matrix for the DCGT11T302M-FP2 WEP10C insert. How does the Rhombus 55° geometry affect cutting performance? The Rhombus 55° shape on the DCGT11T302M-FP2 format allows versatile approach angles and helps balance cutting forces, supporting consistent surface quality and flexible toolpath strategies. What advantages does the FP2 chipbreaker provide? The FP2 chipbreaker on the DCGT11T302M-FP2 WEP10C promotes steady chip formation and evacuation, which improves process stability and reduces the likelihood of chip-related interruptions. Is the insert compatible with standard tool holders? Yes, the DCGT-style format is compatible with standard DCGT11 indexable tool holders, enabling secure clamping and straightforward indexing for the insert. What does tolerance class G mean for production? Tolerance class G indicates a consistent manufacturing tolerance that supports repeatable seating and predictable machining results when the insert is used within a system. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanation only. There is no connection between our company and the mentioned brands. The item offered is original, factory-new goods of the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
DCGT11T302ML-FX4 WEP01C WEP01C Wendeplatten - Walter Tools
Take advantage of the combination of precise cermet performance, controlled chip formation and robust geometry for consistent finishing results; order genuine Walter Tools inserts through Metav Werkzeuge or request advisory support from the Metav technical team. DCGT11T302ML-FX4 WEP01C indexable turning insert — Walter Tools, cermet grade with FX4 chipbreaker The DCGT11T302ML-FX4 WEP01C is an indexable turning insert designed for precision finishing and reliable chip control in metalcutting applications. Walter Cermet grade WEP01C FX4 chipbreaker for stable chips Rhombic 55° insert geometry 0.2 mm corner radius, 7° clearance Precision finishing through cermet technology The Walter Cermet series combines a fine-grain cermet cutting grade with a geometry tuned for high-quality surface finishes. The WEP01C grade is formulated to deliver improved wear resistance and dimensional stability during light to medium finishing passes, making it suitable for operations where surface integrity and repeatability matter. This results in fewer rework cycles and a more predictable finishing process, though final material suitability should be verified against the product matrix. Consistent chip control and process reliability The integrated FX4 chipbreaker is engineered to produce compact, manageable chips that reduce interruption and improve tool life. By shaping chip flow at the cutting edge, the FX4 geometry lowers the risk of entanglement and improves evacuation in both intermittent and continuous cuts. Combined with the rhombus 55° form and the 0.2 mm corner radius, this insert supports steady cutting forces and predictable tool behaviour, which is beneficial for shops aiming to increase throughput while maintaining surface quality. Stable clamping and repeatable tolerances for series production With a plate thickness of T3 and tolerance class G, the insert offers the mechanical stability required for repeatable set‑ups and shorter cycle variance in production environments. The DCGT11T302ML-FX4 geometry follows common ISO-inspired design, facilitating integration into existing toolholder systems that accept DCGT-style inserts. For process planning, this combination of geometry and tolerance supports consistent tool offsets and reduces the need for frequent re-qualifications in serial machining. Contact Metav Werkzeuge for tailored advice and availability of genuine Walter Tools inserts; Metav Werkzeuge’s technical consultants will confirm grade suitability and delivery options Technical Data SKU: DCGT11T302ML-FX4-WEP01C-WALTER Label: Drehwendeschneidplatte DCGT11T302ML-FX4 WEP01C Walter Tools Product type: Drehwendeschneidplatte Series: Walter Cermet Grade: WEP01C Chipbreaker: FX4 Shape: Rhombus 55° Execution: T ISO designation: DCGT11T302ML-FX4 WEP01C UID: DCGT11T302ML-FX4-WEP01C-WALTER Facts Clearance angle: 7° Corner radius: 0.2 mm Insert size: 11 Plate thickness: T3 Tolerance class: G Special features Cermet cutting grade FX4 chipbreaker for controlled chip formation Rhombic 55° geometry for versatile turning WEP01C grade – check product matrix for material match Designed for precision finishing and repeatability FAQ What materials is the WEP01C cermet grade suitable for? The WEP01C cermet grade is optimised for finishing applications; specific material suitability depends on the machining matrix and should be checked against Walter Tools’ data for the DCGT11T302ML-FX4 WEP01C insert. Which operations benefit most from the FX4 chipbreaker? The FX4 chipbreaker supports finishing and light to medium turning where compact, controllable chips and stable cutting conditions are required; the DCGT11T302ML-FX4 geometry promotes predictable chip flow. How does the rhombic 55° form affect cutting performance? A rhombic 55° form provides a favourable compromise between strength and accessibility, enabling effective finishing contours while maintaining edge stability and good toolholder compatibility. Will this insert fit standard DCGT toolholders? The DCGT-style designation indicates compatibility with toolholders designed for DCGT inserts; users should confirm holder specifications and clearance requirements for the DCGT11T302ML-FX4 WEP01C. What does tolerance class G mean in practice? Tolerance class G denotes the manufacturing tolerance level for the insert, contributing to consistent seating and repeatable offsets in serial production setups when used with correctly matching toolholders. The Walter AG (brand appearance: Walter Tools), headquartered in Tübingen, is among the world-leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered article is original, brand-new goods from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
DCGT11T302MR-FX4 WEP01C WEP01C Wendeplatten - Walter Tools
Benefit from the combination of Walter Cermet cutting grade and the FX4 chipbreaker for consistent chip control and prolonged edge life; the 0.2 mm corner radius and 7° clearance angle support high‑quality surface finishes and repeatable results. Order the insert directly via Metav Werkzeuge or ask our consultants for process data and cutting recommendations. DCGT11T302MR-FX4 WEP01C – Indexable turning insert, FX4 chipbreaker, Walter Tools The DCGT11T302MR-FX4 WEP01C is a rhombic 55° indexable turning insert designed for precision finishing where consistent chip formation and a fine surface are required Walter Cermet cermet grade WEP01C FX4 chipbreaker for stable chip control 0.2 mm corner radius for fine surface finish 7° clearance angle for secure cutting Stable chip control increases productivity The combination of the FX4 chipbreaker and the WEP01C cermet composition promotes reproducible chip formation even in demanding finishing passes. Stable chips reduce the need for intermittent machine stops and minimise the risk of rework, which improves process reliability and throughput. For manufacturers aiming to lower cost per part, the controlled chip flow and robust cutting edge contribute directly to longer tool life and fewer tool changes. Geometry tuned for precision finishes A 0.2 mm corner radius together with a 7° clearance angle and the rhombic 55° shape delivers a balance between edge strength and the ability to produce tight surface tolerances. The small corner radius supports narrow cutting widths and refined surface texture, while the clearance angle prevents rubbing and reduces heat build‑up. The moderate insert thickness T3 maintains rigidity for stable turning, making the insert suited for repeatable finishing operations where surface quality matters. Practical selection and process guidance for stable results The insert is part of the Walter Cermet series and is identified as DCGT11T302MR-FX4 WEP01C; check the product matrix for specific material suitability and cutting data before application. Choosing the correct cermet grade and chipbreaker combination can shorten setup time and reduce scrap rates. For tailored recommendations on feeds, speeds and tool holders, Metav Werkzeuge offers application support to integrate the insert into existing production flows and help achieve consistent component quality. Contact Metav Werkzeuge for tailored cutting data, application advice and to discuss the Walter Tools DCGT11T302MR-FX4 WEP01C for precision finishing Technical data SKU: DCGT11T302MR-FX4-WEP01C-WALTER Article designation: DCGT11T302MR-FX4 WEP01C Product type: Indexable turning insert Manufacturer: Walter Tools Core dimensions and tolerances Plate size: 11 Plate thickness: T3 Corner radius: 0.2 mm Clearance angle: 7° Tolerance class: G Materials and special features Series: Walter Cermet Grade: WEP01C (cermet) Chipbreaker: FX4 Plate form: Rhombus 55° Material designation: Catalogue dependent FAQ What types of machining is this insert intended for? The DCGT11T302MR-FX4 WEP01C is designed for precision finishing and applications where consistent chip control and a fine surface finish are required. How does the FX4 chipbreaker improve performance? The FX4 chipbreaker on this insert promotes stable chip formation, which enhances process reliability and can extend the effective tool life of the DCGT11T302MR-FX4 WEP01C. What does the WEP01C designation indicate? WEP01C denotes a cermet cutting grade within the Walter Cermet series; material suitability should be confirmed against the product matrix before operation. Which geometrical values influence the surface finish? The 0.2 mm corner radius and the 7° clearance angle, together with the rhombic 55° form, are the primary geometrical features that govern surface quality for this insert. Manufacturer: Walter Tools; Walter AG; Tübingen, Germany; Walter Tools is part of the Walter AG group Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCGT11T304-FL2 WPP20G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold coating and the WPP20G grade to secure longer tool life and consistent turning performance in steel applications; order the insert directly via Metav Werkzeuge or consult our technical team for process optimisation. Drehwendeschneidplatte DCGT11T304-FL2 WPP20G – rhombic 55° insert, Tiger‑tec Gold, Walter Tools The DCGT11T304-FL2 WPP20G is a rhombic 55° indexable insert designed for turning steel, offering optimised chip control and a durable coated carbide grade for productive machining. Tiger‑tec Gold coating for long tool life Optimised FL2 chipbreaker for steel turning Rhombic 55° geometry for versatile operations 0.4 mm corner radius for stable cutting edge High-performance coating for extended cutting intervals The Tiger‑tec Gold coating combined with the WPP20G grade provides a balance between wear resistance and toughness that benefits repetitive turning operations. The coating reduces flank and crater wear, which translates into fewer tool changes, improved component consistency and lower overall machining costs. In practical terms, the coated cemented carbide substrate resists thermal and abrasive loading typical for steel machining, enabling longer uninterrupted cycles and more predictable tool life. Geometry that delivers edge stability and process reliability The rhombic 55° shape and 0.4 mm corner radius give the insert a rigid cutting edge suited to a range of turning tasks, from finishing to light roughing. The combination of 55° geometry and modest corner radius improves access in profiled work and helps maintain surface quality while limiting vibration. The tolerance class G ensures dimensional repeatability of the insert seat, supporting consistent clamping and repeatable results across tool changes. Chip control tuned for steel applications Equipped with the FL2 chipbreaker, the insert manages chip formation for steels (material group P), encouraging short, controllable chips that evacuate reliably from the cutting zone. This reduces potential rework, keeps toolpaths clear and supports safer, more efficient automated cycles. The 7° clearance provides the necessary relief to limit rubbing while maintaining a stable cutting edge under moderate depths of cut. Practical guidance for integration and process improvement The insert is supplied in the DCGT11T304-FL2 cutting geometry and a thickness of T3, size 11, which matches common toolholder standards for turning. The combination of Tiger‑tec Gold technology and the WPP20G carbide specification is optimised for steel machining, offering a practical balance of productivity and edge retention. For shops seeking to increase throughput, this insert supports higher cutting speeds and predictable wear behaviour when paired with appropriate coolant strategies and stable toolholding. Contact Metav Werkzeuge today to discuss how the DCGT11T304-FL2 WPP20G can improve steel turning processes and to receive tailored application advice from our specialists Technical Data SKU: DCGT11T304-FL2-WPP20G-WALTER Designation: DCGT11T304-FL2 WPP20G Type: Drehwendeschneidplatte Series: Tiger‑tec Gold Grade: WPP20G Facts Size: 11 Thickness: T3 Clearance angle: 7° Corner radius: 0.4 mm Geometry: Rhombus 55° Chipbreaker: FL2 Tolerance class: G Special features Coated cemented carbide (Tiger‑tec Gold) Optimised for machining steel (P) Balanced wear resistance and toughness Designed for consistent chip control FAQ What materials is this insert suited for? The DCGT11T304-FL2 WPP20G is specifically optimised for steel (material group P) and the WPP20G grade is tuned to handle the heat and chip formation typical of steel turning. Which chip control regime does this insert use? This insert features the FL2 chipbreaker, designed to produce short, controlled chips in steel turning operations, improving evacuation and cycle reliability. How does the Tiger‑tec Gold coating benefit production? The Tiger‑tec Gold coating reduces abrasive and thermal wear, extending cutting intervals and supporting higher productivity with fewer tool changes. Is the insert compatible with standard DCGT toolholders? Yes, the DCGT11T304-FL2 geometry and size 11 specification match common DCGT toolholder interfaces for turning applications. Protected trademarks and product names are the property of their respective owners. Brand names are stated for clarification; there is no affiliation between our company and the named manufacturers. The offered article is an original, brand‑new product from the manufacturer, Walter Tools. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
DCGT11T304-FL2 WSM01 WSM01 Wendeplatten - Walter Tools
High-performance turning results from the combination of a heat-resistant grade and a wear‑resistant coating: the WSM01 grade in the Tiger‑tec Silver series provides reliable edge stability for stainless steels and superalloys, while the FL2 chipbreaker and a shallow 7° clearance promote controlled chip formation and reduced cutting forces. Order the DCGT11T304-FL2 WSM01 insert directly via Metav Werkzeuge or consult the team for application advice. DCGT11T304-FL2 WSM01 — Turning insert, FL2 chipbreaker, 7° clearance | Walter Tools The DCGT11T304-FL2 WSM01 is a rhombic 55° turning insert developed for machining stainless steel and heat‑resistant superalloys, optimised for stable chip control and reproducible surface finish. *Tiger‑tec Silver series coating for durability *WSM01 grade for stainless and superalloys *FL2 chipbreaker for stable chip formation *0.4 mm corner radius for precise finish Reliable cutting in difficult materials for steady production The Tiger‑tec Silver series, combined with the WSM01 grade, is formulated for demanding materials that generate heat and strain the cutting edge. The insert’s construction—coated cemented carbide—enhances wear resistance and supports consistent cutting conditions when machining stainless steel and nickel‑based alloys. By promoting a stable cutting edge and predictable wear behaviour, the tool contributes to fewer interruptions in the production flow and improved process repeatability. Controlled chip formation and secure cutting mechanics The integrated FL2 chipbreaker is engineered to produce short, manageable chips under a wide range of cutting parameters, reducing the risk of entanglement and downtimes. The modest 7° clearance angle lowers the contact area on the flank face, decreasing cutting forces and heat generation, while the 0.4 mm corner radius supports edge strength without compromising dimensional accuracy. These features together provide dependable chip control and help to maintain tool life under challenging cutting regimes. Geometry and surface quality for accurate turning operations Rhombus 55° geometry delivers a versatile cutting orientation suitable for facing and light profiling, with the 11 mm size and T3 thickness offering a balance of rigidity and accessibility in confined toolholders. The combination of geometry and grade supports consistent surface integrity and repeatable part tolerances, making the insert well suited to batch production where surface finish and reproducibility carry particular importance. Process security, economy and application scope With an emphasis on process stability, the grade’s thermal and mechanical properties make the insert applicable to stainless steel (ISO group M) and to heat‑resistant superalloys and titanium (ISO group S). This targeted suitability reduces the need for multiple tool types across similar applications, supporting economical tooling strategies and streamlined inventory management while maintaining high productivity and component quality. Contact Metav Werkzeuge today for advice on integrating Walter Tools Tiger‑tec Silver inserts into existing turning processes or to confirm stock and delivery options at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: DCGT11T304-FL2-WSM01-WALTER ISO designation: DCGT11T304-FL2 WSM01 Article designation: DCGT11T304-FL2 Manufacturer: Walter Tools Product type: Turning insert Numbers Free angle: 7° Corner radius: 0.4 mm Plate size: 11 mm Thickness: T3 Tolerance class: G Designs / Special features Series: Tiger‑tec Silver Grade: WSM01 (coated cemented carbide) Chipbreaker: FL2 Geometry: Rhombus 55° Applicable materials: stainless steel (M), superalloys and titanium (S) FAQ What materials is this insert suitable for? The DCGT11T304-FL2 WSM01 is designed for stainless steel (ISO group M) and for heat‑resistant superalloys and titanium (ISO group S), benefiting from the Tiger‑tec Silver coating and the WSM01 grade. How does the FL2 chipbreaker affect machining? The FL2 chipbreaker on the insert promotes consistent short chips, improving chip evacuation and reducing the risk of chip-related stoppages during turning operations with the DCGT11T304-FL2 WSM01. What advantages does the 0.4 mm corner radius provide? A 0.4 mm corner radius increases edge strength and contributes to a stable cutting edge while still enabling good surface finish and dimensional accuracy in turned components. Is the geometry suitable for facing and profiling? The rhombus 55° geometry offers flexibility for facing and light profiling tasks; combined with the WSM01 grade, it supports reliable surface quality and repeatable tolerances. Which series and coating technology is used on this insert? This insert is part of the Tiger‑tec Silver series and is made from a coated cemented carbide grade (WSM01), optimised for wear resistance and thermal stability. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen; The Walter AG (brand: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners. The mentioned brand names and trademarks are used for explanatory purposes only and do not imply any affiliation between Metav Werkzeuge and the trademark owners.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com