Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
5.5mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
A compact workshop-grade gauge pin combining ±0.001 mm dimensional accuracy with a 5.50 mm diameter and a 50 mm working length for reliable end‑measurement checks and fixture setting; order the pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.550 — Single workshop test pin, 5.50 mm, ±0.001 mm The gauge pin M323.550 is a single, workshop‑grade inspection pin designed for precision checking, alignment and end‑measurement tasks in metalworking and assembly environments. Tolerance ±0.001 mm precision Diameter 5.50 mm nominal Length 50 mm, workshop grade Special steel construction Delivered in protective transport case Minimal uncertainty for pass/fail and set‑up checks A tolerance of ±0.001 mm positions this inspection pin among high‑precision workshop tools suitable for tight Go/No‑Go checks and comparative measurements. The fine tolerance reduces measurement scatter in routine inspection tasks and supports consistent set‑up of jigs and fixtures. By keeping a predictable nominal diameter of 5.50 mm, the pin functions reliably as a reference element in inspection stacks and assembly gauges. The combination of small form factor and high repeatability makes it suitable where reproducible gauge dimensions matter for process control. Robust construction for frequent handling and machining environments Made from special steel, this test pin is designed to withstand daily workshop use while maintaining its dimensional integrity. The material choice balances hardness, wear resistance and machinability so that the pin remains true over repeated insertions and contact cycles. At a mass of 0.012 kg and a working length of 50 mm, the component is easy to handle yet offers sufficient engagement depth for many alignment and go‑gauge applications. Supplied in a protective transport case, the pin remains protected from knocks and contamination during storage and transport. Integrates cleanly into inspection and tool‑setting workflows As a single gauge element, the pin serves directly in end‑measurement, plug‑type verification and fixture alignment tasks. Its nominal size and tolerance support straightforward interchange with existing gauge sets and reference inserts; the compact format eases storage in tool drawers or inspection kits. The product’s GTIN 4061905059889 and clear article designation simplify catalogue management and inventory tracking within calibration and quality assurance processes, allowing rapid replacement and traceable part control. Proven source and workshop‑focused delivery Offered under the Metav IndustryLine, this workshop version reflects a supplier strategy that emphasises availability, consistent quality and practical packaging for industrial users. Metav’s European distribution and stock handling ensure reliable supply, while the product’s design focuses on practical benefits for machinists and quality technicians who require repeatable, rugged measuring aids. The small, precise test pin works well as a daily reference in production inspection, toolrooms and maintenance departments. For dependable gauge‑work and repeatable setup results, choose the Metav IndustryLine gauge pin M323.550 and contact Metav Werkzeuge for prompt delivery from Emmerich. Technical Data Article number: M323.550 GTIN: 4061905059889 Manufacturer: Metav IndustryLine Facts Diameter: 5.50 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.012 kg Special features Workshop version Material: special steel Delivered in protective transport case Category: Messstifte FAQ What tolerance and dimensions does this gauge pin offer? The gauge pin provides ±0.001 mm tolerance with a nominal diameter of 5.50 mm and a working length of 50 mm, making the M323.550 suitable for tight dimensional checks. Which applications are suitable for this inspection pin? The inspection pin is intended for end‑measurement checks, plug‑type verification, fixture alignment and general set‑up tasks in machining and assembly environments where compact, precise reference elements are required. What material is the pin made from and how does that help? The pin is manufactured from special steel, selected to offer a balance of wear resistance and dimensional stability under frequent handling, which supports long‑term repeatability in inspection routines. Is the pin supplied in protective packaging? Yes, the product is supplied in a protective transport case to reduce risk of damage and contamination during storage and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.61mm Test Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of a highly stable measurement reference with a 5.61 mm diameter and an ultra‑tight ±0.001 mm tolerance, combined with a 50 mm shaft in special steel for long‑term repeatability. Order the M323.561 directly via Metav Werkzeuge or consult our specialists for integration into inspection routines. M323.561 — Precision gauge pin (5.61 mm, ±0.001 mm, 50 mm) The M323.561 is a single precision gauge pin intended for end‑measurement and inspection tasks in workshop and production metrology. Diameter 5.61 mm with tolerance ±0.001 mm 50 mm shaft length for end‑measurements Made from special steel for wear resistance Workshop version for everyday measurement tasks Precision where every micron matters The M323.561 functions as a dedicated plug gauge for end‑measurements, offering a diameter of 5.61 mm with a tolerance of ±0.001 mm. Such specification places the pin in the realm of high‑precision inspection tools, where geometric conformity determines acceptance. Using a reference pin with this level of accuracy reduces measurement uncertainty, simplifies go/no‑go checks and supports consistent quality decisions in serial production. The compact geometry ensures stable seating in fixtures and repeatable contact, which is decisive when converting dimensional checks into reliable process data. Built for repetitive workshop use and traceable performance Constructed from special steel and presented in a workshop version, the pin combines surface hardness with dimensional stability to resist everyday wear. The 50 mm shaft provides sufficient engagement for end‑measurement tasks while remaining easy to handle and position in jigs or collets. The robust material choice minimises fretting and abrasion, extending service life and reducing the need for frequent replacements. This balance of durability and dimensional fidelity supports efficient inspection intervals and lowers total cost of ownership in routine quality control. Practical integration into inspection workflows As a standard reference component, the gauge pin integrates easily into manual inspection benches and automated checking stations. The clear, narrow tolerance band simplifies decision logic for operators and PLC‑based inspection systems alike, helping to speed up throughput without compromising traceability. The M323.561’s compact form factor suits confined measuring fixtures and facilitates quick interchange between measuring points. For inventory and procurement, the component is identifiable by its SKU and GTIN, supporting seamless stock management and audit trails across production sites. For reliable precision parts and production‑grade inspection accessories, request the Metav IndustryLine M323.561 via Metav Werkzeuge and consult our Emmerich team for delivery and application advice Technical data Article number: M323.561 GTIN: 4061905061097 eClass: 21170231 Core data Diameter: 5.61 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Workshop version Material: special steel Intended use: end‑measurements Label: Prüfstift, einzeln, 5,61mm, +/- 0.001 mm Länge 50 mm FAQ Is this gauge pin suitable for serial end‑measurements? Yes. The M323.561 pin, with its 5.61 mm diameter and ±0.001 mm tolerance, is designed for repeatable end‑measurement tasks in production and inspection environments. What material is used and how does it affect wear resistance? The M323.561 is made from special steel, which provides enhanced wear resistance and dimensional stability compared with untreated grades, extending usable service life in workshop applications. Can the pin be used in standard plug‑gauge holders? The pin’s compact form and standard shaft dimensions allow integration into common holders and fixtures used for plug‑gauge checks and alignment tasks. Is a calibration certificate supplied with the pin? No calibration certificate is included by default. Specific calibration or certification can be arranged separately if traceable measurement records are required. How should the gauge pin be stored and maintained? Store the M323.561 in a dry, dust‑free container and keep contact surfaces clean and lightly oiled if stored long term. Handle with care to avoid knocks that could alter the calibrated diameter. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.62mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of ultra-fine ±0.001 mm tolerance, 5.62 mm diameter and robust special-steel workshop construction to secure reproducible end-measure checks and reduce rework; order directly via Metav Werkzeuge or contact the consultants for application advice. Metav IndustryLine Precision Gauge Pin — 5.62 mm, ±0.001 mm, 50 mm The precision gauge pin is a single gauge pin designed for precise end-measurement and verification tasks in workshop and workshop-quality inspection applications. Workshop-grade special steel construction Diameter 5.62 mm, length 50 mm Ultra-fine tolerance ±0.001 mm Supplied in transport case Minimise rework with sub-micron repeatability A measurement standard with an accuracy of ±0.001 mm provides a clear advantage when parts must meet tight fit and clearance specifications. The pin’s 5.62 mm diameter and 50 mm length make it ideal as a reference for end-face checks, go/no-go comparisons and dimensional verification of mating components. Using a dedicated gauge reduces variability inherent to improvised standards and supports quicker decisions on conformity, which in turn lowers scrap rates and shortens inspection loops. Durable workshop design for everyday inspection Constructed from special steel in a workshop-grade finish, this single gauge pin resists everyday handling and keeps its form under normal inspection loads. The workshop execution balances toughness with surface integrity so the reference face remains stable over repeated use. Supplied in a transport case, the pin is protected from knocks and contamination during storage and transfer, preserving the measurement surface and extending service life. Fits smoothly into standard inspection routines The pin is suitable for use in manual and semi-automated measurement setups as a simple, robust reference tool. It functions well for end-measures, bore checks when used as a fixed mandrel and for checking mating surfaces in assembly validation. The straightforward geometry and tight tolerance make it compatible with optical comparators, micrometres and comparator stands, enabling integration without complex retooling of existing processes. Reliability backed by Metav’s quality filter Sourcing from Metav IndustryLine brings the logistical and quality assurance benefits of a dedicated European supplier. Metav’s presence in Emmerich acts as a local quality filter for the market, supporting consistent availability and traceable product provenance. For production environments where reproducibility and dependable supply are equally important, this workshop-grade gauge pin offers a measurable improvement to routine inspection and part acceptance. For precise end-measurement requirements select the Metav IndustryLine gauge pin and contact Metav Werkzeuge in Emmerich for delivery details and consultancy at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: M323.562 GTIN: 4061905061851 Label: Prüfstift, einzeln, 5,62mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.62 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Supplied in transport case for transport protection FAQ What level of precision does this gauge pin provide? The gauge pin delivers an accuracy of ±0.001 mm, making it suitable for fine tolerance end-measure checks and high-precision workshop inspections. Is the pin suitable for bore checking and go/no-go tests? Yes, the pin is intended for end-face checks and can be used as a mandrel for bore verification and simple go/no-go comparisons in workshop settings. Which material is used and how robust is it? Made from special steel in a workshop-grade finish, the pin resists normal handling and maintains form for reliable reference use. How should the pin be stored to preserve accuracy? Keep the pin in its transport case when not in use to protect the measurement surface from contamination and impacts and preserve the reference geometry. Can this gauge pin be used in optical or mechanical comparator setups? The simple geometry and tight tolerance make the pin compatible with comparator stands, micrometres and many optical inspection setups for straightforward integration. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.63mm Gauge Pin ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of ultra‑fine accuracy and robust workshop design for reliable part verification; the 5.63 mm gauge pin with ±0.001 mm tolerance and 50 mm length streamlines dimensional checks and reduces rework. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.563 — 5.63 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) the Gauge pin M323.563 is a single precision pin for dimensional verification and end‑size control in workshop environments ±0.001 mm accuracy for fine tolerance checks Diameter precisely ground to 5.63 mm 50 mm overall length for stable engagement Made from special steel for wear resistance Accurate verification for critical tolerances The core benefit of this instrument is its exceptional measurement precision: with a tolerance of ±0.001 mm, the pin suits fine end‑size inspection, plug gauge checks and comparator set‑ups where repeatability matters. Ground to a nominal 5.63 mm diameter and a nominal length of 50 mm, the geometry offers stable seating in bores and fixtures, reducing lateral play during measurement. Using a single, hardened and finished pin simplifies process control because the dimensional statement is immediate and verifiable; adopters in toolrooms and small‑batch production gain consistent pass/fail data without complex fixtures. The robust finish on the special steel body also extends service life under periodic insertion cycles. Built for workshop use and reproducible handling Designed as a workshop version, the pin combines practical handling with precision. The 50 mm shaft length balances reach and rigidity so that insertion forces remain low while alignment is straightforward, which helps maintain repeatability across multiple operators. The compact mass (approx. 0.013 kg) minimises inertia during handling and reduces wear on mating surfaces. Supplied in a protective transport case, the piece is ready for secure storage and safe transfer between inspection benches. For manufacturers focused on throughput, the result is quicker verification loops and fewer ambiguous measurements. Integration into quality processes and documentation As a discrete gauge element, this pin is ideal for integration into go/no‑go stacks, reference sets and manual gauging routines. Its simple geometry makes it compatible with micrometre checks, height gauges and comparator fixtures for cross‑validation. Traceable labelling and clear identification (SKU M323.563) support inventory control and calibration scheduling within a quality management system. Choosing a standardised pin for routine checks reduces decision time on the shop floor, supports consistent documentation and helps demonstrate control during internal audits. Contact Metav Werkzeuge for tailored guidance and secure the M323.563 gauge pin for dependable dimensional checks in your inspection routine. Technical data Article number: M323.563 GTIN: 4061905061868 Manufacturer: Metav IndustryLine Facts Nominal diameter: 5.63 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: special steel Workshop version Supplied in transport case Category: Gauge pins FAQ What is the declared tolerance of this gauge pin? The gauge pin M323.563 is manufactured and specified to a tolerance of ±0.001 mm, suitable for fine end‑size verification. Can the pin be used in production gauging fixtures? Yes, the workshop‑grade construction and 50 mm length make this pin appropriate for fixture use, stack gauges and manual inspection routines. Which material is the pin made from and why does that matter? Manufactured from special steel, the pin offers improved wear resistance and surface stability, which prolongs service life during repeated insertions. Is the pin delivered ready for storage and transport? The product is supplied in a protective transport case to prevent damage and to simplify handling between inspection points. How is the item identified for stock and calibration control? The item is listed under SKU M323.563 and GTIN 4061905061868, supporting inventory tracking and calibration scheduling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.64mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of workshop-grade reliability and laboratory-level repeatability: the pin combines a 5.64 mm diameter with an accuracy of ±0.001 mm in a 50 mm length, making it ideal for end‑measurement fixtures and inspection benches. Order the gauge pin directly via Metav Werkzeuge or consult the Emmerich team for batch supply and availability. M323.564 gauge pin (single) — 5.64 mm, ±0.001 mm by Metav IndustryLine A M323.564 gauge pin designed for precise end measurements and repeatable inspection tasks in workshop and production environments. Workshop‑grade finish, robust for daily use Diameter 5.64 mm with ±0.001 mm tolerance Length 50 mm suited to end‑measurements Supplied in a transport box for safe handling Precision that minimises rework and inspection time Built for tasks where dimensional certainty matters, this gauge pin delivers a tight tolerance of ±0.001 mm, which reduces the need for repeated checks and corrective work. The controlled diameter of 5.64 mm ensures secure seating in test jigs and plug‑gauges, providing a reliable reference for go/no‑go tests or positional checks. As a single‑piece tool presented in a workshop‑grade configuration, it is easy to integrate into existing measurement routines and reduces cycle interruptions in quality control. Durable construction for repetitive production use Constructed of special steel, the pin resists wear under frequent insertion and withdrawal cycles while keeping its roundness and surface finish. The 50 mm length gives sufficient engagement for many end‑measurement applications without unnecessary overhang, helping to maintain alignment and minimise bending moments during use. The workshop version specification indicates an emphasis on robustness and handling, suitable for assembly lines and tool rooms where tools are subject to regular, practical handling. Practical benefits for fixtures and gaging systems Delivered as a single item and supplied in a transport box, the pin is protected during storage and transit, reducing the risk of damage before commissioning. Its compact mass and consistent form make it suitable as a reference piece in fixture construction, alignment procedures or as a replacement pin in modular gaging systems. The simple geometry and exacting specification help streamline calibration intervals and support predictable measurement results when used as an end‑measure reference. Contact Metav Werkzeuge for availability and advice on integrating Metav IndustryLine gauge pins into inspection fixtures or gaging systems Technical data Article number: M323.564 GTIN: 4061905061875 Label: Prüfstift, einzeln, 5,64mm, +/- 0.001 mm Länge 50 mm Core specifications Diameter: 5.64 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Designation: Workshop version Packaging: Supplied in transport box Supplied as: Single piece Application hint: End measurements / inspection FAQ What are the exact dimensions and tolerance of this gauge pin? The gauge pin M323.564 has a diameter of 5.64 mm, a length of 50 mm and an accuracy of ±0.001 mm. For which measurement tasks is this pin intended? This pin is intended primarily for end‑measurements and repeatable inspection tasks, making it suitable for fixture references, positional checks and go/no‑go applications. What material and durability can be expected? Manufactured from special steel in a workshop version, the pin is designed for frequent use with good resistance to wear while maintaining geometric stability. How is the product delivered and protected in transit? The item is supplied as a single piece and delivered in a transport box to protect the surface and preserve dimensional integrity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.65mm Gauge Pin Single, ±0.001mm, Length 50mm, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Precision measurement performance is delivered by the combination of ±0.001 mm tolerance and a 5.65 mm diameter in a compact 50 mm length, ensuring repeatable end‑measure checks and secure fixture verification; order the gauge pin directly via Metav Werkzeuge or consult our team for application advice. Gauge Pin M323.565 — Workshop gauge pin, Ø 5.65 mm, ±0.001 mm A gauge pin M323.565 designed for precise end‑measure verification and fixture alignment in workshop environments Workshop version, robust design Diameter 5.65 mm for tight fits Tolerance ±0.001 mm for high precision Length 50 mm, compact handling Repeatable accuracy that reduces rework and waste The combination of a ±0.001 mm tolerance and a compact geometry delivers high‑precision verification for end‑measure and go/no‑go tasks. Such fine tolerance reduces the risk of undetected deviations during assembly or inspection, improving first‑pass yields and lowering downstream rework. The performance is particularly valuable where component fit is critical, for example in tight‑tolerance bores or precision jigs, because the narrow dimensional scatter translates directly into fewer production interruptions and more predictable quality metrics. Compact dimensions for practical workshop use With a diameter of 5.65 mm and a length of 50 mm, this test pin combines reach and manoeuvrability without imposing unnecessary bulk in tight fixtures. The short, stiff geometry is suited to manual handling and bench inspection, and the low mass supports quick, repeatable placement. Manufactured from special steel, the pin resists deformation under typical workshop loads and preserves calibration over many cycles, making it a practical choice where space‑efficient gauging is required and handling speed matters. Traceable identification and workshop integration Marked as a single item with SKU M323.565 and GTIN 4061905057533, the pin is suitable for routine inventory and process documentation. The compact format simplifies storage and deployment in standard inspection sets and allows seamless integration into existing quality procedures. As a workshop‑grade tool it provides a straightforward metrological reference for end‑measure checks, fixture benchmarking and quick conformity tests, supporting systematic quality control without overcomplicating the setup. Contact Metav Werkzeuge for individual advice on incorporating this Metav IndustryLine gauge pin into existing inspection routines and for prompt supply from Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical data SKU: M323.565 GTIN: 4061905057533 Manufacturer: Metav IndustryLine Length: 50 mm Diameter: 5.65 mm Weight: 0.013 kg Tolerance: ±0.001 mm Material: Special steel Version: Workshop execution Packaging: single item delivery FAQ What applications is this gauge pin suitable for? This gauge pin is intended for precise end‑measure checks, fixture alignment and go/no‑go verifications in workshop and production environments; the M323.565 is particularly useful where tight fits and repeatable inspections are required. Is the pin supplied as a single unit or in sets? The product is supplied as an individual gauge pin; the designation indicates a single‑item delivery suitable for integration into inspection sets or for standalone use. What material is the pin made from and why does it matter? Made from special steel, the pin offers wear resistance and dimensional stability under normal workshop handling, which helps maintain the specified ±0.001 mm tolerance over repeated use. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.66mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of industrial robustness, sub‑micron accuracy and compact form factor to stabilise inspection routines and reduce rework. With a tolerance of ±0.001 mm, a Ø 5.66 mm gauge dimension and a 50 mm length, ordering is straightforward via Metav Werkzeuge or technical consultants can be contacted for application advice. Metav IndustryLine gauge pin M323.566 — Ø 5.66 mm, ±0.001 mm, length 50 mm The Metav IndustryLine gauge pin M323.566 is a single precision test pin designed for end‑measurement tasks and fine mechanical inspection in workshop environments Metav IndustryLine gauge pin Ø 5.66 mm Tolerance ±0.001 mm for high precision Length 50 mm workshop execution Made from special steel, weight 0.013 kg Stabilise measurements with sub‑micron repeatability The compact probe is engineered to deliver consistent results where tight tolerances matter. With a tolerance of ±0.001 mm, the component supports repeatable go/no‑go checks and final size verification on short production runs or inspection benches. The small diameter (Ø 5.66 mm) minimises probe intrusion and enables accurate contact on narrow bores and small features, which in turn reduces scrap rates and shortens quality loops. Suited for fine‑mechanical and workshop inspection Classified in the Micro category due to its limited measuring span, this test pin is ideal for precision work on small parts, gauges and fixtures. The 50 mm shank length balances accessibility with rigidity for handheld checking or fixture mounting. Constructed for workshop use, the design is optimised for frequent handling and rapid interchange in measuring assemblies, so throughput in the inspection area can be increased without sacrificing accuracy. Durable construction for everyday shop use Manufactured from special steel, the pin provides wear resistance appropriate for regular contact measurement. The low mass (approx. 0.013 kg) helps to reduce dynamic loading in delicate setups and supports stable positioning during tactile checks. As a dedicated end‑measurement tool, the probe is a pragmatic choice for metrology tasks that require both dimensional certainty and a robust, workshop‑grade build. Secure precise end measurements with Metav IndustryLine components — contact Metav Werkzeuge in Emmerich for specification matching and reliable delivery by phone or e‑mail (+49 2822 7131930 / info@metav-werkzeuge.com) Technical Data Article number: M323.566 GTIN: 4061905057540 Manufacturer: Metav IndustryLine Description: Gauge pin, single, Ø 5.66 mm, ±0.001 mm, length 50 mm Facts Diameter: 5.66 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Measuring range: 5.66 mm Special features Workshop execution Material: Special steel Intended use: end measurements Accuracy class: ±0.001 mm FAQ How precise is the gauge pin M323.566? The Metav IndustryLine gauge pin M323.566 is specified to ±0.001 mm, making it suitable for high‑precision end measurements and fine inspection tasks. What applications suit this test pin? This single gauge pin is intended for end‑measurement and fine‑mechanical inspection in workshop and fixture environments, particularly where compact probes and tight tolerances are required. What is the material and durability of the pin? The probe is made from special steel, chosen for wear resistance and stable contact behaviour under regular workshop use. Can the pin be used in fixture assemblies and gauges? Yes, the 50 mm length and Ø 5.66 mm diameter make the pin well suited for integration into gauges, fixtures and short‑reach inspection jigs. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.67mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Precise probe performance and robust workshop construction combine to support repeatable end‑dimension inspections: the ±0.001 mm tolerance and special steel construction deliver consistent results, while the protective case allows safe transport and immediate use in workshop environments. Order the test pin directly via Metav Werkzeuge or consult our specialists for application advice. Precision Test Pin M323.567 — Ø 5.67 mm, ±0.001 mm (Metav IndustryLine) The Precision Test Pin M323.567 is a single workshop‑grade inspection pin for end‑dimension checks and fixture verification in industrial metrology and workshop inspection. Workshop‑grade robustness Ø 5.67 mm with ±0.001 mm tolerance 50 mm length for fixture integration Supplied in a protective case Accuracy that keeps production moving High repeatability is the practical advantage of a ±0.001 mm specification: such fine tolerance reduces ambiguity when checking final dimensions and decreases the risk of rework in serial production. The probe pin functions as a reliable reference in inspection jigs and test fixtures, supporting faster decision‑making during quality control. By converting narrow numerical tolerances into operational certainty, the component helps maintain throughput without sacrificing measurement confidence. Robust workshop design and handling Built as a workshop‑version component from special steel, the pin resists the knocks and handling typical of shop‑floor use. The 50 mm overall length provides secure seating in holders and leaves sufficient protrusion for alignment tasks, while the compact mass minimises inertia during manual handling. Delivery in a protective case preserves the measuring face in transit and storage, ensuring the pin arrives ready for immediate deployment in fixture setups or portable inspection rigs. Typical applications and practical benefits Designed for end‑dimension checks, the pin suits tasks such as gauge setting, fixture verification and reference probing in assembly lines or maintenance bays. As a single inspection pin it integrates cleanly into manual or semi‑automated verification stations, offering a concise solution where tight tolerances are critical. The clear numeric specification and workshop orientation simplify procurement and replaceability, allowing production planners to match inspection hardware directly to quality requirements. For workshop‑grade, high‑precision inspection components choose Metav IndustryLine—contact Metav Werkzeuge for availability and application guidance Technical data Article number: M323.567 GTIN: 4061905058387 EClass: 21170231 Label: Prüfstift, einzeln, 5,67mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.67 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Material: special steel Version: workshop execution Delivery: protective case included Application focus: end‑dimension checks FAQ What tolerance can be expected from this test pin? The pin is specified with a tolerance of ±0.001 mm, which positions it for high‑precision end‑dimension verification in workshop environments. Is the pin suitable for use in fixtures and jigs? Yes, the 50 mm length and workshop‑grade construction make the pin well suited for mounting in fixtures and test jigs; the M323.567 integrates into typical verification setups. What material is used for the probe? The probe is made from special steel, providing robustness for routine workshop handling while maintaining the specified measurement stability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.68mm Gauge Pin, ±0.001mm, Length 50mm, Workshop Version, Special Steel, Supplied In Case - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, ±0.001 mm dimensional precision and a compact 50 mm length for reliable end‑dimension checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.568 — precision 5.68 mm, ±0.001 mm (Metav IndustryLine) A gauge pin designed for straightforward end‑dimension inspection and plug‑gauge tasks, specified at 5.68 mm diameter with a 50 mm length for checks in deeper bores. Workshop version for robust use Diameter 5.68 mm ±0.001 mm 50 mm length for deep bores Delivered in protective transport case Consistent measurement where repeatability matters A compact inspection pin with a specified tolerance of ±0.001 mm supports repeatable pass/fail checks and close‑fit verification in assembly and quality control. The very fine tolerance reduces uncertainty when establishing final dimensions on mating parts, enabling faster decision making on production lines and during set‑up. A clearly defined diameter of 5.68 mm makes the component suitable for comparison against drawing limits and for use as a reference in gauging fixtures. Built for workshop use and long service life Constructed from special steel, this workshop‑specification pin balances surface hardness and resistance to wear without unnecessary brittleness. The workshop version designation indicates components intended for daily handling and transport; the pin arrives in a protective transport case to prevent damage and to keep inspection tools organised. The modest mass supports easy handling for bench testing while preserving the stiffness required for accurate contact measurement. Practical integration in inspection procedures Designed as a single, purpose‑built inspection element, the pin integrates simply into existing gauging sets and plug‑gauge assemblies. Its 50 mm overall length is intended for checks in deeper bores or for reach beyond flanges where short pins would not suffice. Weight and compact form factor allow quick interchangeability in hand‑held routines or fixture checks, streamlining throughput and reducing non‑productive time in routine quality loops. Choose Metav IndustryLine precision—contact Metav Werkzeuge for tailored advice and assured supply from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.568 GTIN: 4061905058394 Category: Messstifte Facts Diameter: 5.68 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Delivered in protective transport case ECLASS: 21170231 FAQ What is the stated precision of the gauge pin? The M323.568 gauge pin is specified with a tolerance of ±0.001 mm, suitable for precise end‑dimension checks. What material is used for the pin? The pin is made from special steel, selected for durability and surface integrity under repeated contact. What are the diameter and length of the pin? Diameter is 5.68 mm with a 50 mm overall length, designed for measurements in deeper bores. Is the pin supplied in protective packaging? Yes, the M323.568 is delivered in a protective transport case to prevent damage during storage and transit. What applications is this pin intended for? Typical uses include final‑dimension verification, plug‑gauge complements and inspection tasks in workshop and assembly contexts where tight tolerances must be verified. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.69mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Finish - Metav IndustryLine
High‑precision workshop test pin combining ±0.001 mm tolerance, compact 5.69 mm diameter and robust special‑steel construction to ensure repeatable end‑measure inspections; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.569 – single test pin, 5.69 mm diameter, ±0.001 mm The gauge pin M323.569 is a workshop‑grade inspection pin designed for end‑measure checks and dimensional control in production and quality environments. Tolerance ±0.001 mm Diameter 5.69 mm Length 50 mm Workshop version design Made from special steel Precision that keeps production stable The compact test pin offers a tolerance of ±0.001 mm, making it suitable where narrow limits and repeatable results matter. Manufactured for inspection tasks, this gauge pin provides a reliable reference for go/no‑go checks, plug gauges and verification of bore diameters. The fine tolerance reduces uncertainty during assembly and helps to avoid costly rework by ensuring that measured components conform closely to specification. Designed for everyday workshop use Built as a workshop version, the pin combines handling convenience with dimensional stability. The special steel construction delivers resistance to wear under regular use while retaining surface finish required for accurate contact measurement. At 50 mm length and only 0.013 kg, the format is easy to integrate into fixtures and portable inspection setups without adding unnecessary bulk, so routine checks remain fast and consistent. Integration and measurement efficiency As a single test pin, the component supports rapid inspection cycles on production lines and in metrology benches. The nominal 5.69 mm diameter and tight tolerance make it especially apt for end‑measure applications and serial inspection of small bores. Using defined, hardened reference pins in measurement routines shortens setup time and clarifies acceptance criteria, which contributes to higher throughput and fewer disputes between production and quality. Traceability, identification and workshop assurance The pin is listed under SKU M323.569 and GTIN 4061905058400 for straightforward inventory control and procurement. Supplied as an individual inspection element, it complements calibration and gauge systems already present in the workshop. Metav IndustryLine’s supply chain focus ensures consistent availability and supports a predictable stocking strategy for inspection tools across manufacturing sites. Choose the M323.569 from Metav IndustryLine for reliable end‑measure checks and contact Metav Werkzeuge in Emmerich for specification advice via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: M323.569 SKU: M323.569 GTIN: 4061905058400 ECLASS: 21170231 Facts Diameter: 5.69 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Workshop version Material: Special steel Single test pin configuration Compact, low‑mass design FAQ What nominal diameter and tolerance does this test pin have? The gauge pin is specified at a nominal 5.69 mm diameter with a tolerance of ±0.001 mm, suitable for precise bore and end‑measure checks. Is the pin suitable for use in fixture and gauge assemblies? Yes, the single‑piece design of the M323.569 is intended for integration in fixtures, plug gauges and handheld inspection tools where a compact, hard reference is required. What material is used and how does it affect wear? The pin is made from special steel, providing a balance between surface hardness and damage resistance for typical workshop inspection routines. Does the product include a calibration certificate? Calibration status is not specified in the product data; the listing does not indicate a supplied calibration certificate. How is the item identified for procurement and inventory? The part is identified by SKU M323.569 and GTIN 4061905058400 for clear ordering and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.6mm Gauge Pin ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
High-precision test pin with ±0.001 mm tolerance and a compact 5.60 mm diameter provides repeatable end‑measurement references; the workshop design in special steel and delivery in a protective case support durable everyday use. Order directly via Metav Werkzeuge or consult our advisors for application advice. Test pin M323.560 – 5.60 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Test pin M323.560 is a precision end‑measurement pin designed for workshop inspection and end‑dimension checks in fine mechanical and toolmaking environments. ±0.001 mm tolerance for micrometre accuracy 5.60 mm diameter with 50 mm length Workshop design in special steel Supplied in protective transport case Precision where it matters most The inspection pin is machined to a ±0.001 mm tolerance, providing micrometre‑grade repeatability for reference and end‑dimension checks. With a compact diameter of 5.60 mm and a length of 50 mm, the component serves as a reliable reference in tight assemblies and gauge setups. Classified in the Micro category (measurement range up to 10–100 mm), this format prioritises rigidity and stability over long spans, making it particularly well suited to fine mechanical tasks such as component end‑measurements, small bore gauges and precision fit tests. The narrow profile minimises sag and contact ambiguity, so measurement variation is reduced and inspection throughput becomes more consistent. Built for routine workshop use Constructed from special steel and labelled as a workshop execution, the pin combines dimensional fidelity with day‑to‑day durability. The robust material selection supports repeated handling and insertion without rapid wear of the critical diameter. The compact mass (approx. 0.013 kg) and the short, stiff geometry ensure secure seating in fixtures and gauges; handling is straightforward and positioning is fast, which streamlines inspection cycles. Supplied in a protective transport case, the item remains shielded during storage and movement, reducing the risk of damage to the reference surface and preserving long‑term accuracy. Practical integration and application As an end‑measurement reference, this pin is useful for setting limits, verifying bores or serving as a master datum in assembly checks. Its precision rating and compact form factor make it compatible with bench fixtures, portable measuring rigs and comparative measuring procedures where a small, stable reference is required. The product bears the internal article code M323.560 and is traceable by GTIN for inventory and quality‑management processes. Use of a standardised, tight‑tolerance inspection pin reduces uncertainty in repeat measurements and supports reliable decision making in production and quality control. Choose the Metav IndustryLine M323.560 for consistent end‑measurements and long‑term workshop reliability — contact Metav Werkzeuge in Emmerich for application guidance or to place an order via info@metav-werkzeuge.com or +49 2822 7131930 Technical specifications Article number: M323.560 GTIN: 4061905060786 Brand: Metav IndustryLine Key measurements Diameter: 5.60 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Measurement range category: Micro (≤ 10–100 mm) Special features Workshop execution Material: Special steel Supplied in protective transport case ECLASS: 21170231 FAQ What level of accuracy does the test pin provide? The test pin M323.560 is manufactured to a tolerance of ±0.001 mm, delivering micrometre‑level accuracy suitable for precise end‑measurements. For which applications is this inspection pin suitable? The inspection pin is intended for end‑dimension checks, reference seating and small‑bore verification in fine mechanical, toolmaking and workshop inspection tasks. Is the pin delivered ready for use and protected during transport? Yes, the item is supplied in a protective transport case to preserve the reference surface and support safe handling between workstations. Which material is used for the pin and why does it matter? The pin is made from special steel; this provides dimensional stability and wear resistance appropriate for routine workshop use. How is the product identified for ordering and inventory? The article number is M323.560 and the product can be referenced by GTIN 4061905060786 for procurement and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.71mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Grade - Metav IndustryLine
Take advantage of the combination of ultra‑fine tolerance and compact form for reliable end‑measurement and assembly checks; the solid special steel construction supports repeated workshop use. Order the gauge pin directly via Metav Werkzeuge or consult the team for application advice. Gauge Pin M323.571 — Precision 5.71 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge Pin M323.571 is a single precision test pin designed for end‑measurement and alignment tasks in inspection and workshop environments High‑precision tolerance ±0.001 mm Diameter 5.71 mm for tight fit checks 50 mm overall length for in‑fixture reach Workshop version made from special steel Precision where tolerances decide quality Small deviations can cause costly rework; this gauge pin delivers an accuracy of ±0.001 mm, making it suitable for fine inspection tasks and end‑measure verification. The nominal diameter of 5.71 mm is manufactured to tight limits to ensure repeatable fits in bores and gauge fixtures, which helps to reduce measurement uncertainty and throughput interruptions. As a measuring artefact with a 50 mm length, it supports both surface and depth checks while maintaining dimensional stability. Robust construction for repeated workshop use Constructed from special steel and presented as a workshop version, the pin balances hardness and toughness for regular handling. The component is lightweight at 0.013 kg, easing manual positioning while preserving rigidity during measurement. The 50 mm length offers sufficient reach for many test setups without compromising handling, so mounting and extraction remain straightforward in the shop environment. Practical applications and handling benefits This precision test pin is intended for end‑measure checks, alignment of fixtures and go/no‑go verification of small bores. Its form factor supports easy integration in inspection benches and assembly jigs; the slim diameter is ideal where clearance is limited. Using a dedicated gauge pin speeds up repetitive checks and decreases machine downtime by providing a fast, unambiguous reference for pass/fail decisions. Traceability and dependable supply for production workflows The component is supplied with traceable identification and is part of a dependable product range intended for industrial use. Selecting this gauge pin contributes to a consistent metrology routine and, when stocked through a reliable distributor, supports uninterrupted production. Metav’s catalogue approach provides access to extensive measurement supplies and a transparent logistics base from Emmerich, enhancing procurement security for precision workshops. For precise end‑measurement and fixture checks, choose the Metav IndustryLine gauge pin M323.571; contact Metav Werkzeuge in Emmerich for ordering and technical consultation via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.571 GTIN: 4061905058424 ECLASS: 21170231 Key measurements Diameter: 5.71 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Materials & features Material: Special steel Product type: Gauge pin / Test pin Version: Workshop execution Designed for end‑measurement applications FAQ What is the declared tolerance of this gauge pin? The declared tolerance for the gauge pin M323.571 is ±0.001 mm, suitable for fine inspection tasks. Which material is used for the test pin? The M323.571 is manufactured from special steel, specified for workshop durability. For which applications is this pin intended? The pin is intended for end‑measure verification, fixture alignment and small‑bore fit checks in inspection and assembly settings. What are the key dimensions to note? Key dimensions are 5.71 mm diameter and 50 mm length; the item weight is 0.013 kg. How is the product identified in inventory systems? Identification: SKU M323.571; GTIN 4061905058424. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.72mm Gauge Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine ±0.001 mm tolerance, compact 5.72 mm diameter and robust special steel construction for reliable end‑measurement control in workshop environments; order the part directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.572 — 5.72 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) A gauge pin (5.72 mm, ±0.001 mm, 50 mm) engineered for precise end‑measurements and repeatable fit checking in workshop settings. Precision tolerance ±0.001 mm Diameter 5.72 mm Length 50 mm Special steel, workshop grade Precision where it counts for assembly and inspection The fine ±0.001 mm tolerance delivers a measurable advantage when verifying end fits, seating depths or bore interfaces. As a single‑piece gauge pin, it provides a stable reference dimension that reduces uncertainty in comparison checks and inline control. The controlled diameter specification of 5.72 mm ensures repeatable contact geometry, which translates into fewer rework cycles and more predictable assembly outcomes. Built for repetitive workshop use with consistent wear resistance Constructed from special steel, this inspection pin combines surface hardness with dimensional stability under normal workshop handling. The 50 mm overall length offers a practical engagement depth for many end‑measurement tasks while keeping the component light at approximately 0.013 kg, facilitating quick manual manipulation and fast cycling on the shop floor. The workshop‑grade finish mitigates premature wear and helps preserve the reference dimension during standard use. Simple integration into gauging processes and fixtures The compact diameter and standardised geometry make the pin suitable for use with pin blocks, fixture seats or bespoke test rigs. As a single test element, it supports efficient verification routines for batch inspections as well as ad‑hoc checks during setup operations. The clear dimensional labelling and GTIN allow straightforward inventory control and traceability within established quality workflows. Reliable measurement behaviour and operational benefit By using a purpose‑made inspection pin, measurement variance due to ill‑fitting tools is reduced and inspection throughput can be increased without sacrificing confidence in results. The product’s specification and workshop orientation provide a pragmatic balance between precision and robustness, supporting consistent quality control in production and maintenance contexts. For precise workshop gauging, request the Metav IndustryLine gauge pin M323.572 via Metav Werkzeuge — Metav’s specialists in Emmerich can advise on fitment and delivery at info@metav-werkzeuge.com or +49 2822 7131930. Technical Data Article number: M323.572 GTIN: 4061905058431 Brand: Metav IndustryLine Facts Diameter: 5.72 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Material: special steel Workshop execution Category: gauge pins Label: Prüfstift, einzeln, 5,72mm, +/- 0.001 mm Länge 50 mm Accuracy variation: ±0.001 FAQ What measurements is this pin intended for? The gauge pin is intended for end‑measurements, fit checks and seating verification where a defined reference diameter of 5.72 mm and tolerance of ±0.001 mm are required. Can the pin be used in fixture blocks or pin sets? Yes, the geometry and standardised diameter allow the pin to be used in pin blocks, seating fixtures and bespoke test rigs for repeatable inspection tasks. What advantages does the special steel construction offer? Special steel provides a balance of hardness and dimensional stability that helps maintain the reference diameter during repetitive use in workshop environments. Is this item part of a branded series? This is supplied under the Metav IndustryLine range and is identified as M323.572 for catalogue and inventory purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.73mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Combine micrometre‑level accuracy with a compact, workshop‑ready design for dependable end‑measurements; the 5.73 mm diameter at ±0.001 mm tolerance and 50 mm length deliver consistent reference fits. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.573 — 5.73 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) A gauge pin designed for precise end‑measurements and reference fitting in workshop metrology, available in a robust workshop execution. Diameter 5.73 mm with ±0.001 mm tolerance 50 mm length in workshop execution Made from special steel for durability Supplied in protective transport case Micrometre precision for repeatable end‑measurements The core advantage of this tool is its extreme accuracy: a tolerance of ±0.001 mm corresponds to 1 µm, making the pin suitable for measurement and inspection tasks where tight form and size control are required. At 5.73 mm diameter the component serves as a precise reference for bore checks, plug‑fits and end‑dimension verification. Such repeatability reduces downstream rework and supports consistent process control in production and quality‑assurance setups. Built for workshop use and safe handling Manufactured in special steel and specified as a workshop execution, the pin combines strength with a compact footprint. The 50 mm overall length provides a balance between handling convenience and sufficient engagement depth for many small to medium components. Supplied in a protective transport case, the item remains protected during storage and transit, helping to preserve the calibrated condition and surface integrity that determine reliable measurements. Practical integration into inspection routines As a small, high‑precision reference element, the pin integrates easily into bench inspection workflows, gauge assemblies and fixture checks. The compact mass and standard form factor permit rapid placement and comparison measurements, speeding up routine checks without sacrificing accuracy. Traceable identification via the SKU and GTIN supports inventory control and quality documentation, simplifying audit trails and part tracking across production stages. Proven supply and support from Metav IndustryLine Metav IndustryLine delivers this component as part of a broader offering engineered for practicality and reliability. Backed by Metav's logistics and quality filter in Emmerich, the product is supported by decades of metrology experience and a broad industrial catalogue, which helps teams standardise tools and reduce supplier complexity. The combination of precision, durable materials and workshop suitability makes this a pragmatic choice for engineering shops and quality departments seeking dependable reference pins. For precise end‑measurements choose the Metav IndustryLine gauge pin M323.573 — contact Metav Werkzeuge in Emmerich for tailored advice and fast dispatch via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.573 GTIN: 4061905058448 Manufacturer: Metav IndustryLine Facts Diameter: 5.73 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Workshop execution Supplied in transport case FAQ What level of accuracy does this gauge pin offer? The gauge pin delivers ±0.001 mm accuracy, equating to 1 µm, which makes the M323.573 suitable for high‑precision end and reference measurements in workshop metrology. For which tasks is this pin best suited? This precision pin is intended for end‑dimension checks, reference fitting and plug‑fit inspections where a 5.73 mm nominal diameter and tight tolerance are required. What material is the pin made from and why does it matter? Constructed from special steel, the pin combines wear resistance with dimensional stability, ensuring sustained measurement reliability under normal workshop conditions. Is the item delivered ready for use and how is it protected? The product is supplied in a protective transport case, which keeps the surface and dimensions secure during storage and transport, preserving measurement quality. How can the product be identified and ordered? The item is listed under SKU M323.573 and GTIN 4061905058448; these identifiers facilitate ordering and stock control for the Metav IndustryLine gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.74mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
High-precision Ø 5.74 mm gauge pin with a tolerance of ±0.001 mm and a 50 mm working length ensures dependable end‑measurement checks; the workshop version in special steel and delivery in a protective case supports repeatable results and safe transport. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.574 – gauge pin, Ø 5.74 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.574 is a workshop‑grade, single test pin designed for precise dimensional verification and end‑measurement applications in production and quality control environments Workshop version for robust use Diameter 5.74 mm with ±0.001 mm accuracy Length 50 mm in special steel Delivered in protective case Precision that secures measurement decisions Manufactured for tasks where tolerances are decisive, this test pin offers ±0.001 mm accuracy across its nominal 5.74 mm diameter. Such precision reduces downstream rework by providing a clear, objective reference when verifying bores, gauge blocks or finished end‑masses. The fine tolerance class makes the pin suitable for use in calibration benches and fixture checks where measurement uncertainty must be minimised. The compact geometry and tight specification allow integration into existing inspection jigs without complex adaptation, supporting faster throughput in series inspection while maintaining documented traceability. Built to withstand workshop conditions Designed as a workshop version, the pin combines a practical length of 50 mm with a hard‑wearing special steel. The material choice balances surface stability and corrosion resistance, ensuring consistent contact geometry over many inspection cycles. Delivered as a single item in a protective case, the pin is ready for safe storage and transport between workstations or to the inspection lab. Robustness in the component reduces the need for frequent replacement and supports reliable measurement routines under everyday shopfloor handling, contributing to lower operational disruption and longer service life. Streamlined use in inspection workflows As a single test instrument, the pin is straightforward to implement in go/no‑go checks, plug gauge arrangements and comparative setups. The slim profile and low mass make the item easy to position for quick go‑checks or when used as a reference in gauge assemblies. Laboratory technicians and production inspectors benefit from the repeatability granted by the component’s geometry and finish, enabling consistent results across shifts. Where documentation is required, the clearly specified tolerance and material data simplify reporting and quality records, supporting supplier audits and internal process control. For precise end‑measurement and dependable shopfloor inspection, contact Metav Werkzeuge to order the Metav IndustryLine gauge pin M323.574 or request tailored application guidance from our advisors. Technical data Article number: M323.574 GTIN: 4061905059407 Label: Prüfstift, einzeln, 5,74mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.74 mm Accuracy/tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Single item delivery Delivered in protective case Intended for end‑measurement and dimensional verification FAQ Is the gauge pin supplied ready for immediate inspection use? The gauge pin M323.574 is delivered as a single workshop unit in a protective case and can be used immediately for dimensional checks. What tolerance class does this test pin meet? This test pin provides an accuracy of ±0.001 mm, suitable for high‑precision verification and fine tolerance control. Can the pin be used for bore verification and plug gauge tasks? Yes, the Ø 5.74 mm pin is suitable for plug gauge arrangements and quick bore checks as part of standard inspection routines. What material is the pin made from and how does that affect longevity? Constructed from special steel, the pin offers durable contact surfaces and resistance to wear, supporting long service life under normal workshop conditions. Is the item supplied individually or as part of a set? The product is supplied as a single test pin (single item delivery), packaged in a protective case for transport and storage. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.75mm Test Pin, Single, ±0.001mm, Length 50mm, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of workshop‑grade robustness combined with micrometre‑class accuracy: the pin’s ±0.001 mm tolerance and 5.75 mm diameter ensure reliable end‑size inspection, while the 50 mm length and protective transport case support safe storage and handling. Order directly via Metav Werkzeuge or consult our technical team for specification advice. Test pin M323.575 — single gauge pin, 5.75 mm, ±0.001 mm The Test pin M323.575 is a workshop‑grade gauge pin for precise end‑size checks and fixture alignment in metalworking and toolmaking environments. Workshop version for rugged use Diameter 5.75 mm with ±0.001 mm tolerance Length 50 mm for fixture and gauge applications Supplied in protective transport case Precision where it counts in production High‑accuracy pin gauges are a simple but decisive element for consistent quality control. With a tolerance of ±0.001 mm, this gauge pin delivers micrometre‑class repeatability that reduces false rejects and limits rework time. The tight specification is particularly beneficial for end‑size verification and plug gauges used during setup, where consistent diameter control shortens inspection cycles and increases throughput. The result is fewer production holds and a more predictable quality flow. Robust design tailored to workshop routines Constructed from special steel, this workshop‑grade pin combines surface stability with resistance to everyday handling. At 50 mm overall length and a mass of approximately 0.013 kg, the component is easy to manipulate in fixtures and assembly benches yet stiff enough for reliable seating in bores and gauges. Delivery in a protective transport case keeps the measuring surface clean and prevents dings during storage or transit, so the pin remains ready for immediate use when called upon at the workbench. Practical gains for tooling and inspection Integrating a precision gauge pin into inspection routines simplifies go/no‑go assessments and fixture adjustments. The compact geometry makes the pin suitable for tight‑tolerance bores and alignment jigs, supporting fast comparative measurements and reducing set‑up time. As an individual measuring item, it complements gauge sets or acts as a replacement part in maintenance stocks, contributing to lower downtime and consistent production quality. The clear specification and single‑piece supply suit both small workshops and larger production lines seeking straightforward, measurable improvements. For workshop‑ready precision from Metav IndustryLine, request the M323.575 gauge pin via Metav Werkzeuge or contact our Emmerich team for tailored advice and supply options: info@metav-werkzeuge.com Technical data SKU: M323.575 GTIN: 4061905059414 Diameter: 5.75 mm Length: 50 mm Tolerance: ±0.001 mm Material: Special steel Weight: 0.013 kg Delivered in protective transport case Numbers / Core technical data Diameter: 5.75 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg GTIN: 4061905059414 Special features / Versions Workshop version Single test pin Protective transport case for delivery Intended use: end‑size inspection and fixture alignment FAQ What tolerance can be expected from this gauge pin? The M323.575 gauge pin is specified with a ±0.001 mm tolerance, providing micrometre‑class accuracy suitable for end‑size verification. Which material is used for the pin? The pin is made from special steel, chosen for dimensional stability and robustness in workshop use. Is the pin supplied ready for use and protected during transport? Yes, the item is supplied as a single test pin and shipped in a protective transport case to preserve the measuring surface. Can this pin be used for fixture alignment and gauge sets? The compact 5.75 mm diameter and 50 mm length make the M323.575 suitable for fixture alignment, plug checks and as a replacement part in gauge sets. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.76mm Gauge Pin Single ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
High-precision end-dimension checks become straightforward with a 5.76 mm gauge pin that delivers ±0.001 mm repeatability over a 50 mm shaft; combine this dimensional accuracy with workshop-grade construction for dependable verification in production and inspection tasks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application-specific guidance. M323.576 gauge pin — 5.76 mm, ±0.001 mm accuracy, 50 mm length M323.576 is a precision gauge pin designed for end‑dimension and positional verification in workshop and inspection environments. ±0.001 mm tolerance for high-precision checks 5.76 mm diameter matched to end‑dimension control 50 mm shaft for accessible insertion depth Special steel construction for workshop execution Consistent micron-level verification for production control The gauge pin provides a reliable reference for final dimension checks, with a stated ±0.001 mm accuracy that supports high‑precision tasks where repeatability matters. The small diameter makes the component suitable for tight tolerances and fine fits, while the specified tolerance establishes a quantifiable basis for pass/fail decisions in inspection routines. This level of precision reduces uncertainty in critical measurements and helps maintain product quality across serial production. Robust design tailored to workshop routines Manufactured in special steel and labelled as a workshop execution, the probe is built for frequent handling and insertion cycles typical in daily measurement tasks. The 50 mm shaft length gives enough engagement for many end‑dimension and positional checks without compromising handling comfort, and the single‑piece format simplifies stockkeeping and replacement. The overall design balances durability with the fine detail required for accurate gauging, making it practical for both bench inspection and in-process checks. Easy integration into quality workflows As a compact test pin, the component slots into existing gauge sets, fixtures or test jigs and supports straightforward comparison measurements and functional go/no‑go routines. The clear specification of diameter, length and tolerance enables rapid documentation in inspection plans and traceability records. Where consistency of result is essential, the defined metrology parameters allow planners to model measurement uncertainty and to align the probe with current quality standards. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine gauge pin M323.576 into inspection routines and to secure reliable supply from Emmerich. Technical data Article number: M323.576 GTIN: 4061905059421 Manufacturer: Metav IndustryLine Facts Diameter: 5.76 mm Length: 50 mm Tolerance/accuracy: ±0.001 mm Weight: 0.013 kg Special features Material: special steel Workshop execution Single-piece probe format FAQ What measurement accuracy does the gauge pin offer? The gauge pin delivers an accuracy of ±0.001 mm, making the M323.576 suitable for high-precision end‑dimension verification. Is the probe suitable for routine workshop use? Yes, the workshop execution and special steel construction of the M323.576 ensure it withstands regular handling and insertion cycles typical in inspection stations. How deep can the pin be inserted for checks? The 50 mm shaft provides the insertion depth required for most end‑dimension and positional checks while maintaining shaft stability. Can the pin be used within existing gauge sets or fixtures? The compact, single-piece format of this gauge pin allows straightforward integration into standard gauge sets and test jigs for comparative or go/no‑go measurements. What information is available for traceability? Specification details such as diameter (5.76 mm), length (50 mm) and tolerance (±0.001 mm) are provided for inclusion in inspection plans and traceability documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.77mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
Combining micron-level accuracy, a compact Micro-range format and a workshop-ready design ensures reproducible inspection results with minimal rework; ideal for precision fits and quality checks in small assemblies. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.577 (single test pin, 5.77 mm, ±0.001 mm) — Metav IndustryLine Gauge pin M323.577 is a single test pin for high-precision dimensional inspection in fine mechanical and workshop environments Micron-level tolerance ±0.001 mm Precision ground 5.77 mm diameter Workshop-ready with transport case Reproducible accuracy for small diameters The gauge pin delivers a measured diameter of 5.77 mm with an exceptional ±0.001 mm tolerance, making it suitable where tight fits and minimal clearance are critical. Thanks to its fine tolerance, the pin reduces the need for iterative adjustments and rework during assembly or inspection processes, improving throughput in small-part production. The compact dimensions and precision finish facilitate use in gauging fixtures and comparative checks where consistent contact and repeatability are required. Built for daily workshop use and longevity Manufactured from special steel and specified as a workshop version, the test pin resists everyday handling and retains dimensional stability under regular inspection cycles. The hardened and ground surface ensures reliable contact geometry, which maintains measurement integrity over time and reduces the frequency of replacements. This robustness supports continuous production checks and lowers overall maintenance effort by providing a stable reference for go/no-go tests and fit verifications. Practical handling and ready-to-store organisation With a length of 50 mm and a lightweight construction (approximately 0.013 kg), the pin is easy to position in jigs and fixtures, while remaining rigid enough for precise insertion. Delivery includes a transport case suitable for workshop use, which protects the pin during transit and storage and simplifies inventory management. The compact format is particularly advantageous in confined measurement setups and for technicians who require a portable, reliably protected reference gauge. Streamlined inspection workflows and traceability Designed as a straightforward inspection tool, the pin integrates smoothly into manual and semi-automated checking routines. Clear identifiers such as M323.577 and GTIN: 4061905059438 enable rapid ordering and stock control in procurement systems. The combination of a micro-range format with micron tolerance supports quality assurance steps that prevent downstream assembly issues, helping to reduce scrap and ensure component interchangeability across batches. Contact Metav Werkzeuge for availability and tailored advice on integrating this Metav IndustryLine gauge pin into existing inspection routines Technical data Article number: M323.577 GTIN: 4061905059438 Category: Gauge pins Facts Diameter: 5.77 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: special steel Workshop version Delivery: in plastic or wooden transport case SKU: M323.577 FAQ What applications is this gauge pin suited for? This gauge pin is intended for fine mechanical inspection and small-part checking; the Metav IndustryLine gauge pin M323.577 is especially useful for precision fits and dimensional verification in miniature assemblies. Does the pin come with a certificate of calibration? No calibration certificate is specified for this item; the Metav IndustryLine product M323.577 is supplied as a precision ground test pin for workshop use without an ISO 17025 certificate unless specifically ordered. How should the pin be stored between uses? Store the test pin in its supplied transport case to protect the ground surface and ensure long-term dimensional stability; the case included with M323.577 simplifies organised storage. Can the gauge pin be used in gauging fixtures? Yes, the compact length and rigid design make the pin suitable for gauging fixtures and manual go/no-go checks as part of standard inspection equipment. How can M323.577 be ordered or referenced? Refer to article number M323.577 or GTIN 4061905059438 when ordering to ensure exact identification of the Metav IndustryLine gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.78mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
The combination of ±0.001 mm tolerance, a precise 5.78 mm diameter and a robust 50 mm length delivers reproducible inspection results and reduced scrap rates on the shop floor; choose this gauge pin for dependable end‑measure checks and controlled interchangeability. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application support. Gauge pin, 5.78 mm, ±0.001 mm, 50 mm — Metav IndustryLine A gauge pin designed for precision end‑measure inspection in workshop and production environments. High-precision tolerance ±0.001 mm Diameter 5.78 mm exact ground Length 50 mm for component checks Workshop design in special steel Consistent dimensional control to speed inspection A finely ground gauge pin with a diameter of 5.78 mm and a rated tolerance of ±0.001 mm provides a reliable reference for go/no‑go checks and tight fits. The very small tolerance reduces measurement uncertainty, which in turn lowers the risk of rejected parts and rework. Using a dedicated inspection mandrel instead of improvised gauges shortens throughput times in quality control, as one defined reference replaces repeated comparative methods while improving traceability during series testing. Material and manufacturing benefit accuracy and durability Manufactured from special steel, the pin combines surface hardness and corrosion resistance suited to regular workshop use. The precision grinding process creates a consistent cylindrical profile that maintains contact geometry during measurement, supporting repeatable results. The robust material choice and workshop specification mean the pin resists wear from frequent insertion cycles, so calibration intervals are extended and tool life is increased — an economic benefit for production and maintenance planning. Practical form factor for everyday checks With a 50 mm overall length, the inspection pin reaches typical bore depths while remaining easy to handle and position in fixtures. The compact but deliberate length ensures stable seating during end‑measure inspections and reduces bending or misalignment compared with overly long probes. Designed for straightforward use in assembly, jigs and test benches, the pin integrates seamlessly into existing workflows and supports rapid in‑process verification without special adapters. Traceability, identification and workshop readiness Each unit is supplied as a single, individually identified gauge pin, complete with a unique article reference and GTIN for inventory and quality records. The product’s workshop classification highlights suitability for everyday production tasks rather than delicate laboratory work, offering a balance between precision and robustness. For production environments seeking standardised inspection tools, this pin provides an accessible and durable solution that aligns with industrial quality processes. For application advice or to secure a steady supply of Metav IndustryLine inspection tools, contact Metav Werkzeuge in Emmerich—our team will advise on integration and deliverability to match production requirements. Technical Data Article number: M323.578 GTIN: 4061905059445 Manufacturer: Metav IndustryLine Facts Diameter: 5.78 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Workshop version Material: special steel Delivered as single gauge pin SKU: M323.578 FAQ What measurement accuracy can be expected from this gauge pin? The gauge pin offers a rated accuracy of ±0.001 mm, making it suitable for high‑precision end‑measure inspections where tight tolerances are required. Is the material suited for regular workshop use and frequent handling? Yes; the pin is made from special steel and specified as a workshop version, combining durability with the surface properties needed for repeated insertion and removal. Can this pin be used for bore checks and component end‑measure inspections? The 5.78 mm diameter and 50 mm length make this pin ideal for bore checks and end‑measure verification of through‑holes and seating features in typical production parts. How is the product identified for inventory and traceability? The item is supplied with an article number (M323.578) and GTIN (4061905059445) for simple tracking in quality and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.79mm Test Pin ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of industrial accuracy, compact dimensions and robust workshop design to streamline end‑measure inspections; the precise ±0.001 mm tolerance on a 5.79 mm diameter pin and a 50 mm length supports consistent pass/fail decisions on the shop floor. Order the item directly via Metav Werkzeuge or consult the team for application advice. Gauge pin M323.579 – 5.79 mm, ±0.001 mm, length 50 mm (Metav IndustryLine) The gauge pin M323.579 is a single precision measuring pin designed for end‑measure verification and dimensional checking in workshop and inspection environments. Precision ±0.001 mm tolerance Diameter 5.79 mm for end‑measure checks Length 50 mm for compact fixture use Workshop version made from special steel Faster, more reliable inspection decisions through tight tolerance control With a declared ±0.001 mm variation, this measuring pin reduces uncertainty in pass/fail checks and supports faster quality decisions. The narrow tolerance translates into fewer ambiguous readings during go/no‑go checks, which in turn lowers rework rates and shortens inspection cycles. By combining a fine tolerance with a defined diameter, the pin ensures repeatable contact geometry, making it suitable for routine dimensional verification where consistent results are required. Robust material and compact form for daily workshop use Manufactured from special steel, this workshop‑grade pin resists wear under frequent use while maintaining its measuring edge and surface integrity. The 50 mm length provides a compact handling profile that is easy to install in fixtures or use freehand when checking end‑measures on small to medium components. The solid construction and balanced mass support stable contact during measurement, helping to avoid bounce or misalignment that could compromise a reading. Integrates with existing checking workflows and fixtures Designed as a single measuring element for end‑measure applications, the pin fits into common gauge sets and dedicated checking fixtures to expand existing inspection capabilities. The compact design and low mass facilitate fast swapping and positioning, making it practical for repetitive quality tasks. Lightweight handling minimises operator fatigue during batch inspection and the clear nominal diameter supports traceable results within an established measurement routine. For workshop‑grade precision from Metav IndustryLine, request the M323.579 gauge pin via Metav Werkzeuge for supply and technical advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical Data Article number: M323.579 GTIN: 4061905059452 Brand: Metav IndustryLine Facts Diameter: 5.79 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Workshop execution Material: special steel Single measuring pin for end‑measure checks Intended for compact fixture and handheld use FAQ What is the primary application for this gauge pin? The gauge pin M323.579 from Metav IndustryLine is intended for end‑measure verification and dimensional checking in workshop and inspection settings. Does the pin resist wear during frequent use? Yes, the pin is made of special steel, which offers increased wear resistance appropriate for recurring shop‑floor inspection tasks. How does the ±0.001 mm tolerance affect inspection? A tight ±0.001 mm tolerance provides clearer pass/fail decisions and reduces ambiguous measurements during routine checks. Can the pin be used in existing fixtures and gauge sets? The compact 50 mm length and standardised diameter make the pin compatible with common fixture arrangements and gauge sets for end‑measure checks. Is the gauge pin supplied individually or in sets? This item is supplied as a single measuring pin (single unit), suitable for adding to bespoke gauge arrangements or replacing worn elements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.7mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
This precision 5.70 mm gauge pin, with ±0.001 mm tolerance and a 50 mm length, delivers reliable inspection results and repeatable fits for small-bore components; its special steel construction suits demanding workshop use. Order the item directly via Metav Werkzeuge or request advice from our consultants for application-specific guidance. Gauge pin M323.570 – 5.70 mm diameter, ±0.001 mm tolerance by Metav IndustryLine A gauge pin M323.570 engineered for precision inspection and fixture verification in workshop and metrology environments. 5.70 mm diameter precision pin Tolerance ±0.001 mm for high accuracy Length 50 mm for deeper bores Workshop-grade special steel construction Precision that secures measurement confidence The combination of a 5.70 mm nominal diameter and ±0.001 mm tolerance makes this gauge pin a dependable reference for tight-tolerance checks. Designed to provide high accuracy in repetitive inspections, the test pin minimises uncertainty when verifying bores, pins and mating features. The narrow tolerance range supports quality assurance processes by reducing rework and ensuring parts conform to specified fits. Where repeatable results matter, a hardened, dimensionally stable reference like this plays a decisive role. Robust design for everyday workshop handling Built as a workshop version, the pin uses special steel to resist wear during frequent use. The 50 mm length reaches deeper features while remaining simple to handle and store; its compact mass supports fast alignment in gauges and fixtures. The construction balances surface hardness with corrosion resistance so the component retains dimensional integrity across standard workshop conditions. This focus on durability translates into fewer replacements and lower lifecycle costs for routine inspection tools. Practical integration into inspection workflows As a precision reference component, the pin integrates seamlessly into caliper, bore gauge and fixture checks, helping to accelerate inspection cycles without compromising accuracy. The modest weight and straight geometry make it suitable for manual and jig-based verification routines. Traceability is supported by clear identification: article number M323.570 and GTIN are provided in the technical data for inventory and quality records. For users seeking stable, workshop-capable gauges, this precision pin offers a straightforward, low-overhead way to tighten process control. Choose the Metav IndustryLine gauge pin M323.570 for dependable workshop accuracy; contact Metav Werkzeuge for tailored advice or to arrange supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.570 GTIN: 4061905058417 Manufacturer: Metav IndustryLine Weight: 0.013 kg Label: Prüfstift, einzeln, 5,70mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 5.70 mm Tolerance: ±0.001 mm Length: 50 mm Mass: 0.013 kg Special features Material: Special steel Version: Workshop execution Single test pin for inspection and fixture use FAQ What is the nominal diameter and tolerance of this pin? The gauge pin has a nominal diameter of 5.70 mm with a tolerance of ±0.001 mm, specified for the M323.570 precision pin from Metav IndustryLine. Can this pin be used for bore checking in fixtures? Yes, the M323.570 gauge pin is intended for fixture and bore verification; its 50 mm length is suited to checking deeper bores and aligning components. What material is the pin made from? The pin is manufactured from special steel, selected for wear resistance and dimensional stability in workshop conditions. Is the pin supplied individually or in a set? The product is supplied as a single gauge pin, article number M323.570, suitable for inventory by piece. How does this pin support quality assurance processes? With a tolerance of ±0.001 mm, the pin provides a stable reference for repeatable inspections, helping to reduce measurement uncertainty and support consistent acceptance criteria. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.81mm Test Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine tolerance, compact dimensions and workshop‑grade robustness to secure reliable end‑measurement references. Order the gauging pin directly via Metav Werkzeuge or contact our consultants for application advice. M323.581 Gauging pin – Metav IndustryLine (Ø 5.81 mm, ±0.001 mm) A gauging pin designed for precise end‑dimension checks and reference tasks in workshop metrology, offering micrometre‑level reproducibility in a compact format Workshop version for robust daily use Diameter 5.81 mm with ±0.001 mm accuracy 50 mm ground length for stable reference Precision that reduces rework and inspection time The core advantage of this tool is its ±0.001 mm nominal tolerance, which corresponds to 1 µm resolution in practice and provides a dependable reference for fine fitting and go/no‑go verification. A cylindrical diameter of 5.81 mm is produced to tight limits so that the component or gauge where it is used registers minimal clearance variation. By using a dedicated gauging pin as a reference mandrel or alignment aid, measurement uncertainty is reduced and downstream rework is avoided—benefits that translate directly into shorter inspection loops and steadier production outcomes. Durable design for everyday workshop routines Manufactured from special steel in a workshop version, the pin combines surface hardness with a ground finish along the 50 mm usable length to ensure consistent contact geometry and wear resistance. The compact mass and small cross‑section make handling straightforward while the ground length provides a stable datum against which measurements or settings can be repeatedly made. Delivery in a protective transport case preserves the ground surfaces during storage and transport, helping to maintain the original tolerance over many inspection cycles. Traceability, cataloguing and practical integration Lightweight construction (approximately 0.013 kg) and single‑piece supply simplify inventory and tool‑setting logistics. The item is listed under SKU M323.581 and GTIN 4061905060335, making procurement and traceability straightforward for quality documentation. Suited to end‑dimension checks and fixture setting, this compact reference element fits into standard inspection workflows and complements other workshop gauges. Metav IndustryLine provides the logistical and quality‑assurance backbone from Emmerich, ensuring availability and a consistent supply chain for routine and scheduled measurement tasks. For specific advice on integrating the M323.581 gauging pin into inspection routines or to secure stock for production, contact Metav Werkzeuge in Emmerich by phone on +49 2822 7131930 or by email at info@metav-werkzeuge.com Technical data SKU: M323.581 GTIN: 4061905060335 Brand: Metav IndustryLine Description: Single gauging pin Ø 5.81 mm, ±0.001 mm, length 50 mm Facts Diameter: 5.81 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.013 kg Special features Material: Special steel Workshop version Delivered in transport case Single piece supply Category: Gauge pins Application: End measurements FAQ What tolerance does this gauging pin offer? The M323.581 gauging pin from Metav IndustryLine is specified at ±0.001 mm, providing micrometre‑level reference accuracy for inspection and setting tasks. Is the pin suitable for regular workshop use? Yes — the workshop version is manufactured from special steel with a ground 50 mm length and is supplied in a transport case to protect the measuring surface during daily handling. How is the item identified for procurement and documentation? The product is listed as SKU M323.581 with GTIN 4061905060335, which supports straightforward ordering and traceability in quality records. For which measurement tasks is this pin typically used? This gauge pin is intended for end‑dimension checks, fixture alignment and as a reference mandrel in workshop inspection processes where consistent contact geometry is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.82mm Test Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-ready robustness, micron-level accuracy and practical handling for consistent inspection results; order directly via Metav Werkzeuge or ask the consultants for application advice. M323.582 Test Pin (Gauge Pin) – 5.82 mm Ø, ±0.001 mm, 50 mm length | Metav IndustryLine The M323.582 is a compact test pin designed for precision end‑measure checks and gauge applications in workshop and inspection environments. Workshop-grade construction Diameter 5.82 mm, tolerance ±0.001 mm Length 50 mm for stable handling Delivered in protective transport case Accuracy that saves time and rejects The M323.582 is engineered for repeatable measurements where small deviations matter. With a diameter of 5.82 mm and a verified tolerance of ±0.001 mm, this precision pin reduces measurement uncertainty during dimensional checks and fixture set‑up. The tight tolerance corresponds to micron-level control, which often translates into fewer reworks and more reliable process decisions. As a result, inspection cycles become more predictable and quality gates are easier to enforce. Built for workshop use and straightforward handling Constructed in special steel, the test pin combines wear resistance with a compact 50 mm shank that is easy to seat in holders or gauges. The workshop-grade execution ensures robustness against daily handling, while the modest mass of 0.013 kg contributes to convenient manipulation without excess inertia. Delivery in a protective transport case preserves the measurement face during storage and transport, keeping the function ready for immediate use on the shop floor. Seamless integration into inspection routines This gauge pin fits standard plug and gauge arrangements and is suitable for end‑measure verifications, alignment of fixtures and quick go/no‑go checks where a defined diameter reference is required. The simple geometry minimises operator influence and supports consistent tactile positioning in assemblies. The combination of compact form and high repeatability makes the pin a practical component within quality control processes and assembly jigs. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to secure the M323.582 and confirm suitability for specific inspection tasks — Metav Werkzeuge is available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M323.582 GTIN: 4061905060342 Manufacturer: Metav IndustryLine Material: Special steel Weight: 0.013 kg Facts Diameter: 5.82 mm Length: 50 mm Tolerance: ±0.001 mm Mass: 0.013 kg Special features Workshop-grade execution Protective transport case included Precision tolerance for end-measure checks Compact form for fixture and gauge integration FAQ What are the exact dimensions and tolerance of this gauge pin? The gauge pin measures 5.82 mm in diameter with a tolerance of ±0.001 mm and a length of 50 mm, making it suitable for fine dimensional references. Which material is used for the test pin? The M323.582 is manufactured from special steel, chosen for wear resistance and stability under normal workshop conditions. Is the pin supplied in a protective container? Yes, the item is shipped in a protective transport case to reduce the risk of damage during handling and storage. For which inspection tasks is this product intended? Typical uses include end‑measure checks, fixture alignment, plug‑gauge references and rapid go/no‑go verification where a precise diameter datum is required. Is a calibration certificate included with the pin? Product data does not specify a calibration certificate. For traceable calibration options or certificates, select versions or services that explicitly list calibration details. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5.83mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine precision, robust special steel construction and protective transport packaging for reliable inspection and reference measuring in workshop environments. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for batch or delivery enquiries. M323.583 Gauge pin — 5.83 mm, ±0.001 mm (Metav IndustryLine) The M323.583 gauge pin is a single inspection pin designed for end‑measure checks, reference gauging and fixture setup in workshop metrology. Precision ±0.001 mm for micrometric checks Nominal diameter 5.83 mm Length 50 mm, workshop version Supplied in transport case Accurate reference for quick pass/fail checks The M323.583 serves as a compact, high‑precision gauge pin for repetitive verification tasks. With a tolerance of ±0.001 mm, the pin provides micrometric certainty when used as a reference element in plug gauges, jigs or inspection fixtures. The small footprint and 50 mm shank length make it particularly useful where space is limited but measurement certainty must not be compromised. Measurable performance reduces rework and supports consistent production quality by turning intermittent checks into reliable, repeatable data points. Durable workshop design that handles everyday use Manufactured from special steel, this inspection pin combines hardness with corrosion resistance suited to routine workshop handling. The workshop version finish balances wear resistance and ease of cleaning, while the low mass (approx. 13 g) simplifies handling during rapid inspection cycles. Delivered in a protective transport case, the pin arrives ready for insertion into toolboxes or inspection kits—minimising the risk of damage during transit and storage and ensuring the calibrated geometry remains intact for practical use. Practical benefits for quality assurance and fixture building As a single, nominally 5.83 mm plug, the component is ideal for end‑measure verification, alignment references and setting gauges during assembly and maintenance work. The clearly defined tolerance and compact form factor support faster decision making on the shop floor, reducing downtime caused by uncertain measurements. For procurement and planning, the product is offered under the Metav IndustryLine umbrella, which emphasises accessible precision and dependable supply for industrial customers and specialist workshops. Contact Metav Werkzeuge for tailored delivery options, batch supply or advice on integrating the M323.583 gauge pin into existing inspection routines Technical Data Article number: M323.583 GTIN: 4061905060359 ECLASS: 21170231 Material: Special steel Version: Workshop execution Facts Nominal diameter: 5.83 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.013 kg Special features Single inspection/gauge pin Supplied in transport case for secure transit Workshop finish for daily use FAQ What is the declared tolerance of the gauge pin? The declared tolerance is ±0.001 mm for the M323.583 gauge pin (Metav IndustryLine), suitable for micrometric reference checks. Is the pin suitable for use in inspection fixtures and jigs? Yes, the M323.583 inspection pin is designed for fixture integration and end‑measure reference use in workshop metrology applications. What material is the pin made from and how does that affect durability? The pin is manufactured from special steel, which provides enhanced wear resistance and robustness for routine shop‑floor handling. Does the product come with protective packaging? The M323.583 is supplied in a protective transport case to reduce handling damage during storage and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com