Precision rulers for accurate alignment
Precision rulers are specialised measuring tools used to check flatness and straightness in metalworking and inspection processes, providing reliable alignment and verification for assemblies and machined surfaces. They are typically made from stainless steel or precision metals and serve machining, optics, electronics and quality control applications where tight tolerances are required; using a precision ruler improves repeatability and reduces non‑conformances. Common synonyms include straight edge and flatness gauge, and the durable construction alongside fine graduations ensures the tool remains accurate over years of workshop use.
500x40x5 mm Workshop Rule Ground Steel, Polished - Metav IndustryLine
Take advantage of the combination of a 500 mm measuring length, ground special steel construction and a flat 40 x 5 mm profile for stable, repeatable layout work; order the tool directly via Metav Werkzeuge or consult the team for application advice. Workshop ruler 500 x 40 x 5 — flat steel rule for robust workshop layout (Metav IndustryLine) The Workshop ruler 500 x 40 x 5 is a flat steel rule designed for precise marking and measuring in metalworking, fabrication and general workshop use. 500 mm length for extended reach Ground special steel surface for durability Flat profile 40 x 5 mm for stable measurements No chamfer for full-length reference edge Precision and a reliable reference edge for layout work The flat, ground special steel construction offers a consistent, wear-resistant measuring surface that supports accurate marking and repeatable checks. With a full length of 500 mm and a profile of 40 x 5 mm, the rule provides a rigid reference that resists bending during hand-held use, which is essential when transferring lines across plates or setting out assemblies. The absence of a chamfer means the full edge can be used as a datum, simplifying tasks where a continuous reference is required. The combination of a ground finish and stable cross-section reduces edge wear and maintains measurement integrity over long service intervals. Designed for dependable handling and workshop efficiency The flat geometry and modest mass (approximately 0.8 kg) deliver a balance between heft for stability and manoeuvrability for frequent use. The 40 mm width increases contact area, improving lateral stability when scribing or checking straightness on components. Classified for large-format workshop measuring at the 500 mm range, this tool suits layout work on medium-sized parts, jigs and fixtures where a robust, easy-to-read reference rule speeds up production tasks. The ruled profile lends itself to repeatable marking and quick comparative measurements without the need for complex setups. Built for durability and smooth integration into the workshop A ground surface finish provides resistance to abrasion and straightforward cleaning after cutting or filing operations, extending service life and reducing downtime for maintenance. The robust build aligns with Metav’s approach to accessible precision: durable tools that suit both industrial environments and busy workshops. As a straightforward steel rule, it integrates seamlessly into standard layout kits and tool stations, offering a low-complexity solution for repeatable results and clear reference lines across common fabrication applications. For robust, accurate layout tasks choose the Metav IndustryLine workshop ruler—contact Metav Werkzeuge in Emmerich for specification details or purchasing guidance at info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M214.702 GTIN: 4054469109473 SKU: M214.702 Facts Length: 500 mm Cross section: 40 x 5 mm Weight: 0.8 kg Tariff code: 90178010 Special features Material: ground special steel No chamfer (full-length reference edge) Category: Rulers / Lineale FAQ Is this ruler suitable for heavy fabrication layout work? The workshop ruler 500 x 40 x 5 from Metav IndustryLine is intended for medium to large workshop tasks; its 500 mm length and flat 40 x 5 mm profile provide the stiffness required for reliable layout on many fabrication jobs. Can the rule be used as a datum edge for repeated scribing? Yes. The absence of a chamfer gives a continuous reference edge that is suitable for repeated scribing and transfer marking with consistent results. What material is the ruler made from and how does that affect durability? Manufactured from ground special steel, the ruler resists abrasion and maintains edge integrity over prolonged use, reducing the need for frequent replacement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50mm Glass Rule For Microscope Calibration With 0.1mm Scale, Supplied In Case - Metav IndustryLine
Take advantage of a compact, soda‑lime glass reference that combines a fine 0.1 mm engraved scale with a measurement range suited to precision optical checks; its low weight and stable material support repeatable microscope verification. Order directly via Metav Werkzeuge or consult our specialists for application advice. Glass ruler by Metav IndustryLine — 0–50 mm, 0.1 mm scale Glass ruler for quick verification and alignment tasks in optical inspection and microscopy; a compact, high‑contrast reference tool for laboratories and inspection benches. Made from soda‑lime glass 0–50 mm measurement range 0.1 mm engraved scale High precision: (1.5+2L/1000) µm Precise, stable reference for optical checks Constructed from soda‑lime glass, this compact reference offers a stable, non‑reactive surface that keeps markings sharp and readable. The 0–50 mm measurement range places the tool in the micro class for fine mechanical work, where short jaws and minimal flexure deliver the best repeatability. The engraved 0.1 mm graduations provide a clear visual reference for alignment and calibration tasks, while the stated accuracy formula (1.5+2L/1000) µm indicates a tolerance that increases predictably with length—making uncertainty easier to quantify for quality documentation. Practical benefits for laboratory and workshop use The low mass (approximately 0.03 kg) and slim profile support quick handling during routine checks without adding thermal or mechanical load to delicate setups. Optical verification tasks benefit from the glass’s transparency and contrast against microscope reticles, improving positional accuracy when setting or checking scales. For inspection benches focused on small components or watchmaking, the combination of compact design and reliable graduations speeds up processes and reduces rework, offering a tangible efficiency advantage in daily quality routines. Handling guidance and integration into workflows Careful handling preserves the reference surface: clean with a lint‑free cloth and mild glass cleaner, avoid abrasive pads and sudden temperature shifts. The ruler’s dimensions (total length 80 mm, width 30 mm, thickness 5 mm) mean it fits comfortably into inspection jigs or alongside other optical references. For traceable measurement chains, discuss calibration options with Metav Werkzeuge; the tool is designed to serve as a stable visual and dimensional check within existing quality procedures and documentation practices. Contact Metav Werkzeuge for tailored advice on using the Metav IndustryLine glass ruler in microscope verification and to discuss calibration or batch requirements — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M910.321 GTIN: 4061905450037 Material: sodium glass Total length: 80 mm Measurement range: 0–50 mm Facts Width: 30 mm Thickness: 5 mm Weight: 0.03 kg Scale: 0.1 mm Accuracy: (1.5+2L/1000) µm Special features Application: verification of microscopes Category: Rulers (Lineale) Engraved, high‑contrast graduations Lightweight, compact design FAQ What material is the ruler made from and why is it suitable for microscopes? The ruler is made from sodium glass; this material offers stable, non‑reactive surfaces and good contrast, which helps when aligning and checking microscope scales with the Metav IndustryLine glass ruler (SKU M910.321). How precise is the measurement reference? Precision is given as (1.5+2L/1000) µm, a tolerance that grows with length; this predictable behaviour makes the glass ruler suitable as a repeatable reference in optical checks and documentation. Is the ruler suitable for watchmaking and micro components? Yes. With a 0–50 mm range and fine 0.1 mm graduations, the tool fits micro‑class applications where compactness and minimal flexure support accurate, repeatable checks. How should the ruler be cleaned and stored? Use a lint‑free cloth and mild glass cleaner; avoid abrasive agents and sharp impacts. The Metav IndustryLine glass ruler should be stored flat and protected from hard knocks to preserve the engraved scale. Can the ruler be used as part of a calibrated measurement chain? The ruler serves as a stable reference for visual and dimensional checks; for traceability or specific calibration certificates, consult Metav Werkzeuge to arrange suitable calibration services. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50mm Glass Ruler For Microscope Verification, 0.5mm Scale, Packed In Case - Metav IndustryLine
Take advantage of the combination of compact format, reliable accuracy and stable soda‑lime glass construction for precise visual inspection and verification tasks; order the Glass ruler directly via Metav Werkzeuge or ask our consultants if needed. Glass ruler M910.322 — Soda‑lime glass, 0.5 mm scale (Metav IndustryLine) The Glass ruler M910.322 is a compact inspection ruler for microscope verification and fine measurement tasks in the micro measurement range. Compact 80 mm overall length for fine tasks 0.5 mm etched scaling for clear readings Soda‑lime glass for dimensional stability Low mass 0.03 kg for easy handling Precision tailored to small parts and optical checks The instrument is designed for micro-range measurement work, with a measuring span up to 50 mm, which places it in the category for extremely compact, high-resolution inspection tools. The 0.5 mm etched scale gives clear visual graduations, while the quoted accuracy formula of (1.5 + 2L/1000) µm describes the typical deviation behaviour across the length — a concise way to estimate tolerances when comparing or calibrating small features. Together, these attributes support repeatable readings on small components and optical instruments without introducing excessive handling complexity. Stable material and compact geometry for repeatable readings Made from soda‑lime glass, the ruler combines dimensional stability with a smooth reading surface, reducing the risk of wear that can obscure fine graduations. With an overall length of 80 mm, a width of 30 mm and a thickness of 5 mm, the geometry keeps the instrument stiff enough for short-span measurements while remaining easy to position under optics. The low mass (0.03 kg) minimises movement during inspection and helps when aligning the scale under a microscope or camera, simplifying routine verification work in laboratories and inspection benches. Practical integration into inspection workflows Marked with a clear 0.5 mm scale and identified by SKU M910.322 and GTIN 4061905448980, the ruler is suited to visual verification, reference marking and comparative inspection tasks. Its compact format makes it suitable for watchmaking, micro‑assembly or quality control benches where short, precise reference lengths are required. Metav’s supply chain and local presence in Emmerich ensure dependable availability and a consistent quality filter for the European market, supporting workshops and small labs that require dependable, easy‑to‑use measurement aids. Contact Metav Werkzeuge in Emmerich for technical advice and fast supply of the Metav IndustryLine Glass ruler M910.322 Technical data Article number: M910.322 GTIN: 4061905448980 Name: Glass ruler M910.322 Core dimensions Overall length: 80 mm Measuring range: 0–50 mm Width: 30 mm Thickness: 5 mm Mass: 0.03 kg Materials & features Material: soda‑lime glass Scale: 0.5 mm etched Accuracy: (1.5 + 2L/1000) µm Category: micro‑range inspection ruler FAQ What measurement span does the ruler cover? The glass ruler covers a measuring range from 0 to 50 mm and is therefore classified for micro‑range inspection tasks suitable for fine parts. Is the material suitable for optical work and microscope checks? Yes, the soda‑lime glass surface is dimensionally stable and provides a clear, wear‑resistant scale ideal for microscope verification and visual comparison. How is accuracy specified for the instrument? Accuracy is given as (1.5 + 2L/1000) µm, which indicates the expected deviation related to length; this allows assessment of suitability for small‑part inspection. Can the ruler be used for dimensioning tiny components on the bench? The compact format and clear 0.5 mm graduations make the ruler suitable for bench reference, marking and quick comparative checks of small components. Which identifiers help with stock and ordering? Use SKU M910.322 or GTIN 4061905448980 to identify the exact Metav IndustryLine glass ruler when ordering or checking stock. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600 mm Working Scale 40 x 5 mm With Millimetre Graduation DIN 866/B - Metav IndustryLine
Take advantage of a 600 mm working length, ground special steel construction, and clear millimetre graduation for reliable large‑format layout and marking. Order the working scale directly via Metav Werkzeuge or consult our team for application advice and availability. Metav IndustryLine Working Scale M214.713 – 600 x 40 x 5 mm, DIN 866/B, millimetre graduation The Metav IndustryLine working scale M214.713 is a heavy‑duty, ground steel rule designed for precise layout and marking of larger components in metalworking and fabrication. 600 mm working length Ground special steel profile Conforms to DIN 866/B Precise millimetre graduation Precision for repeatable layout on large components The 600 mm length combined with a ground special steel profile provides a straight, stable reference for scribing and marking. Compliance with DIN 866/B guarantees that the scale meets established flatness and graduation standards, so measurements and transfer marks remain reliable over repeated use. The mm graduation is optimised for quick, unambiguous readings during layout operations, reducing rework and cycle time in the workshop. Robust construction that endures shop use A ground surface finish and solid profile give the scale mechanical resistance and long service life under typical workshop conditions. At approximately 1.2 kg, the rule is heavy enough to lie flat during marking yet light enough for single‑person handling. Its build quality suits plant‑level tasks and assembly‑line layout where a Large (500–1,000 mm) measuring range is required, combining reach with the rigidity necessary to maintain accuracy across the full length. Practical handling that speeds up daily work The millimetre divisions are clearly engraved and contrasted for rapid visual recognition when marking or checking dimensions. The robust edges are suitable for use with scribers and layout punches, and the flatness of the rule supports accurate baseline transfers. For workshops that require traceable calibration or integration into quality procedures, Metav Werkzeuge can advise on available services and documentation to match internal control systems. Contact Metav Werkzeuge in Emmerich to confirm stock status and discuss how the Metav IndustryLine working scale M214.713 fits specific layout or inspection workflows Technical data SKU: M214.713 GTIN: 4054469109558 Label: Arbeitsmaßstab 600 x 40 x 5 mm DIN 866/B, mit mm-Teilung Material: Spezialstahl, geschliffen Standard: DIN 866/B Facts Length: 600 mm Width: 40 mm Thickness: 5 mm Weight: 1.2 kg Tariff number: 90178010 Special features Millimetre graduation Ground surface for flatness Conforms to DIN 866/B Classified for Large (500–1,000 mm) measuring range FAQ What material is the rule made from? The Metav IndustryLine working scale M214.713 is made from special steel, ground, which gives a stable reference edge and good wear resistance. Is this scale suitable for metal layout and scribing? Yes, the M214.713 is intended for layout work on metal and other robust materials; the flat, ground profile and clear mm graduation support precise scribing and marking. Does the scale meet any industrial standards? The working scale conforms to DIN 866/B, ensuring standardised graduation spacing and surface flatness for reproducible measurements. How long is the working range and what does that imply? With a 600 mm working range, the rule falls in the Large (500–1,000 mm) category, offering the reach needed for larger components while retaining stiffness for accurate transfers. How should the rule be stored to preserve accuracy? Store the Metav IndustryLine working scale flat or hung by a protective edge to avoid bending; keep it dry and away from corrosive environments to maintain the ground surface. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600 mm Workshop Rule 40 x 5 mm Ground Special Steel - Metav IndustryLine
Taking advantage of a ground special steel construction and a compact 600 mm working length results in reliable, repeatable layout work and easy handling on the shop floor; precise alignment and robust contact surfaces minimise rework and downtime. Order the workshop ruler directly via Metav Werkzeuge or contact the sales team for application advice. Workshop ruler 600 x 40 x 5 (M214.703) — Ground special steel, 600 mm measuring bar by Metav IndustryLine The Workshop ruler 600 x 40 x 5 is a durable, ground special-steel measuring bar designed for precision layout, marking and simple dimensional checks in general workshop and production environments. Ground special steel construction 600 mm working length 40 mm width for rigidity Flat finish for stable contact Precise layout and repeatable results for everyday tasks The ground special-steel surface delivers a consistently flat reference that supports repeatable layout and marking tasks. Thanks to the 600 mm working length and 40 mm profile, the rule combines reach with stiffness, reducing deflection during use and ensuring that measurements remain consistent across repeated operations. The flat finish provides reliable contact for scribes, punches and dial gauges, making the tool suitable for routine workshop quality checks and setup tasks where speed and dependability matter. Built for robustness and straightforward handling A workshop-focused design means the ruler tolerates the rougher conditions of a production environment without compromising function. The special steel, ground construction resists wear on the contact surfaces and maintains straightness over time, which lowers the frequency of replacement and reduces unplanned downtime. The absence of a chamfer keeps one edge fully usable as a reference face for marking and clamping, while the compact cross-section facilitates single-person handling and quick positioning on benches or fixtures. Practical integration into shop workflows This measuring bar supports rapid measurements and marking without complicated setup: its clear geometry aids fast alignment and it fits standard workshop tool racks and storage. The robust format is compatible with visual inspection, layout operations and simple comparative gauging; calibration is straightforward when required and identification via the M214.703 SKU and GTIN assists inventory management. For teams seeking a dependable, low-maintenance reference bar, the product offers a pragmatic balance of stability and usability. Request Metav Werkzeuge’s supply information for the Metav IndustryLine workshop ruler M214.703 and receive guidance from the Emmerich-based team to ensure the ruler matches specific workshop requirements Technical data Article number: M214.703 GTIN: 4054469109480 EClass: 21170122 Tariff number: 90178010 Manufacturer: Metav IndustryLine Facts Length: 600 mm Width: 40 mm Thickness: 5 mm Material: special steel, ground Special features Ground surface for stable reference Without chamfer for full-edge use Workshop-optimised geometry Category: Lineale FAQ What is the primary application of this ruler? The workshop ruler M214.703 from Metav IndustryLine is intended for layout, marking and basic dimensional checks in workshop and production settings. Is the ruler suitable as a reference for scribing and clamping? Yes, the ground special-steel face of the Metav IndustryLine workshop ruler provides a stable reference surface suitable for scribing, clamping and comparative checks. How is the ruler identified for inventory and procurement? Identification is via the article number M214.703 and GTIN 4054469109480, which are printed or recorded for ordering and stock control. Can the ruler be used on a hard-wearing shop floor without rapid wear? The ground special-steel construction of the workshop ruler is designed to resist normal workshop wear and maintain functional flatness over extended use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600mm Steel Scratch Gauge Hardened Ground Lapped DIN 874/0, 2kg - Metav IndustryLine
Take advantage of the combination of stainless steel construction, DIN 874/0 flatness, and a stable 600 mm working length for reliable workshop inspection and layout tasks; order the hairline straight edge directly via Metav Werkzeuge or contact our consultants for application advice. Hairline Straight Edge M214.126 — stainless steel, DIN 874/0, 600 mm (Metav IndustryLine) The Hairline Straight Edge M214.126 is a hardened, ground and lapped stainless steel reference tool designed for flatness checks, layout work and inspection tasks in workshop and metrology environments. Hardened stainless steel construction Lapped and ground flatness surface Conforms to DIN 874/0 accuracy Precise flatness control for inspection benches The straight edge is manufactured from stainless steel, fully hardened, ground and lapped to provide a consistently flat reference over its length. Conformity with DIN 874/0 signals the highest tolerance class for straight edges, which translates into repeatable visual and feeler‑gauge checks during acceptance testing or daily inspection routines. The measured flatness and surface finish reduce measurement uncertainty when comparing workpieces or setting up inspection fixtures, offering a pragmatic way to maintain quality without requiring specialised laboratory equipment. Robust construction that supports daily workshop use A robust mass of 2 kg and the choice of stainless steel provide both stability and corrosion resistance for routine handling on the shop floor. The hardened construction resists wear from scribing and light contact, while the lapped surface ensures minimal local deviation when performing lay‑out scribing or edge alignment. This combination of durability and stable geometry helps to shorten setup times and reduces the frequency of rework caused by unreliable references, improving throughput in production and maintenance workflows. Practical dimensions and traceable identification for quality processes With a working length of 600 mm, the tool bridges bench‑scale inspection and larger format layout tasks, making it suitable as a universal reference for many machine‑shop applications. The item is identified as SKU M214.126 with GTIN 4054469106762, which supports traceability in procurement and stock systems. The straight edge functions as a comparative reference for flatness checks and alignment; for documented calibrations or laboratory standards, integration into a traceable measurement chain is recommended to complement workshop checks and maintain quality records. Enquire with Metav Werkzeuge for application guidance or to request the Metav IndustryLine Hairline Straight Edge M214.126 for your inspection bench — our specialists in Emmerich can advise on fitment and use. Technical data SKU: M214.126 GTIN: 4054469106762 ECLASS: 21170120 Customs tariff: 90173000 Facts Length: 600 mm Weight: 2 kg Standard: DIN 874/0 Special features Material: stainless steel, fully hardened, ground and lapped Category: rulers / straight edges Intended use: flatness checks, layout, inspection FAQ Is this straight edge suitable for precision inspection work? The Hairline Straight Edge M214.126 from Metav IndustryLine meets DIN 874/0 and is intended for workshop‑level flatness checks and layout tasks where a high‑quality visual reference is required. How should the straight edge be maintained to preserve accuracy? Regular cleaning, avoidance of knocks and storage in a dry area preserve the ground and lapped surface; minor handling wear can be monitored with feeler gauges and routine visual inspection of the reference edge. Can the tool be used for alignment and scribing? Yes — the weight and straightness of the 600 mm edge make it suitable for scribing, alignment and comparative checks on machine beds and assemblies. Is the material corrosion‑resistant for use in humid workshops? Constructed from stainless steel, the straight edge offers good resistance to corrosion for typical workshop environments; standard care further extends service life. How is the product identified for procurement and inventory? The item is listed as SKU M214.126 with GTIN 4054469106762 to support ordering and traceability in stock systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600mm Steel Straightedge Blackened Ground Lapped, DIN 874/0 - Metav IndustryLine
Combine DIN 874/0 reference accuracy with a hardened, ground and lapped tool-steel blade and a compact 600 mm length for dependable alignment and inspection. Order the Precision Straightedge 600 mm DIN 874/0 directly via Metav Werkzeuge or ask our consultants if needed. Precision Straightedge 600 mm DIN 874/0 — hardened tool steel, blackened finish (Metav IndustryLine) The Precision Straightedge 600 mm DIN 874/0 is a hardened, ground and lapped reference blade intended for alignment, inspection and workshop metrology tasks. DIN 874/0 certified reference accuracy Hardened, ground and lapped tool steel 600 mm measuring length for workshop tasks Blackened finish reduces glare and corrosion Accurate reference for alignment and inspection The straightedge serves as a stable reference for run‑out checks, squareness verification and surface alignment thanks to its DIN 874/0 classification. This class denotes the highest tolerance within the DIN 874 standard for straightness, which translates into a measurable reduction in setup time and rework during assembly and inspection. By providing a verified straight datum, the blade supports reproducible results in both manual checks and comparison procedures. Robust construction for everyday workshop use Constructed from hardened tool steel that is ground and lapped, the blade combines stiffness with a finely finished measuring face to resist wear under frequent handling. The mass—approximately 2 kg—adds stability during contact measurements and helps maintain consistent contact pressure when used against heavy parts. The combination of heat treatment and lapping ensures the tool keeps its flatness over time, reducing the need for frequent reconditioning. Practical dimensions that suit standard metrology tasks At 600 mm, this straightedge covers the most common inspection range in mechanical workshops and small jig and fixture assembly. The length offers an optimal balance between reach and rigidity, making the blade easy to manoeuvre while still suitable for checking medium‑sized components and tables. The preserved datum edge allows for quick comparison checks against machine beds, vises and gauge blocks without excessive handling. Visibility and longevity designed into the finish The blackened finish reduces surface glare under workshop lighting and provides a degree of corrosion protection for the steel substrate, extending service life in everyday environments. Precision lapping of the measuring face improves tactile feedback during contact measurements and minimises the risk of introducing measurement errors. For storage, a clean, dry environment is recommended to preserve the finish and the flatness of the reference faces. Choose the Metav IndustryLine Precision Straightedge for reliable workshop references and contact Metav Werkzeuge in Emmerich for detailed specifications and supply Technical data SKU: M214.026 GTIN: 4054469106175 Manufacturer: Metav IndustryLine Standard: DIN 874/0 Facts Length: 600 mm Weight: 2 kg Special features Material: Tool steel, fully hardened, ground and lapped Finish: Blackened (schwarz bruniert) Category: Straightedge / Lineal Tariff number: 90173000 FAQ What level of straightness tolerance does this straightedge provide? The Precision Straightedge 600 mm DIN 874/0 meets the straightness tolerance defined by DIN 874/0, providing the highest class accuracy for visual and tactile reference measurements. Is the blade suitable for use on heavy machine beds and fixtures? Yes. The hardened, ground and lapped construction of the straightedge ensures durable flatness for use as a reference against machine beds, vises and fixtures; the 600 mm length is appropriate for medium‑sized components. What protective properties does the blackened finish offer? The blackened finish on the straightedge reduces glare under bright workshop lighting and offers basic corrosion resistance to protect the steel surface during regular use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600mm Wooden Case For Hairline Scale For 500 And 600 Hairline Scales - Metav IndustryLine
Take advantage of a robust wooden transport case that protects delicate hairline rulers, combines lightweight handling with secure workshop storage and ensures organised tool management; order the item directly via Metav Werkzeuge or consult our specialists for availability and procurement advice. Wooden Case for 600 mm Hairline Ruler (fits 500/600 mm) — Metav IndustryLine Wooden Case for 600 mm Hairline Ruler — a protective storage and transport solution for precision hairline rulers used in workshop and inspection environments. Fits 500 and 600 mm hairline rulers Robust wooden transport case Secure storage for precision instruments Protects precision instruments during transport and storage A purpose-made wooden case delivers reliable protection for measurement tools that demand careful handling. Constructed to house standard hairline rulers up to 600 mm, the box reduces the risk of shocks and knocks in transit and prevents surface damage that can impair measurement accuracy. The combination of robust construction and compact design makes the case a practical choice for workshops and inspection benches where tool preservation and repeatable accuracy matter. Keeps the workshop organised and instruments ready for use Clear organisation reduces downtime: a designated wooden storage box creates a defined place for hairline rulers so they are readily accessible when needed. The low weight of the box (approx. 2 kg) supports easy two-handed handling and straightforward placement on shelving or in vehicles. By keeping instruments protected between uses, the case contributes to longer service life of precision items and minimises the frequency of repairs or replacements, delivering a tangible efficiency improvement to routine measurement workflows. Practical material choice with long-term usability Wood was selected as the enclosure material for its combination of durability and repairability compared with many lightweight synthetics. The plain, solid construction supports simple maintenance and contributes to a professional workshop appearance. For businesses that prioritise reliable storage without complex packaging, this wooden case presents a straightforward solution that complements other precision equipment and aligns with standard workshop logistics. For procurement, availability checks and tailored advice on incorporating this Metav IndustryLine wooden case into workshop tool management, contact Metav Werkzeuge for prompt support and ordering information. Technical Data Article number: M214.026.K GTIN: 4054469106182 Facts Weight: 2 kg Compatible length: fits up to 600 mm Special features Material: wood Suitable for: hairline rulers 500 mm and 600 mm Category: rulers / measuring instruments FAQ Is this case suitable for 500 mm hairline rulers? Yes. The wooden case is designed to accommodate both 500 mm and 600 mm hairline rulers and offers protection during storage and transport. What is the weight of the wooden case? The case weighs approximately 2 kg, providing a balance between sturdy protection and manageable handling. Can the case be used for other measuring tools? The case is intended for hairline rulers up to 600 mm; other slim measuring tools of similar dimensions may also be stored, provided they fit without forcing the lid closed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600mm Workshop Aluminium Ruler With Mm Graduation, Anodised - Metav IndustryLine
Take advantage of a 600 mm straight edge that combines anodised aluminium resilience with a clear mm scale and a non-reflective finish for dependable everyday measuring; order directly via Metav Werkzeuge or consult our specialists for application advice. Workshop ruler M203.054 — Anodised 600 mm aluminium, mm scale (Metav IndustryLine) The Workshop ruler M203.054 is a robust, anodised aluminium measuring rule intended for general workshop marking, setup tasks and quick length checks across metalworking and woodworking applications Anodised aluminium profile Precise mm graduation Non-reflective satin finish Lightweight 600 mm length Reliable measurements for daily workshop tasks The straight profile provides a stable reference for everyday marking and checking tasks. Made from anodised aluminium, the rail resists corrosion and retains its appearance under regular use, while the mm scale delivers straightforward, easily readable graduations for quick verification of lengths up to 600 mm. The combination of a clear scale and a rigid section reduces measuring uncertainty compared with improvised straight edges, which supports faster, more reliable set-ups on the shop floor and at inspection benches. Practical handling that reduces errors and speeds work A matt, non-reflective finish minimises glare under workshop lighting, making it easier to read the graduations without eye strain. The compact cross-section (50 × 5 mm) keeps the rule lightweight (approximately 0.2 kg) yet sufficiently stiff for routine marking and transfer measurements. These qualities translate into time savings: fewer repeated checks, simpler alignment against edges and fixtures, and consistent results when used for layout, scribing or as a partner for square and gauge work. Integration, sourcing and confidence for the production line As part of the Metav IndustryLine, the rule fits a pragmatic procurement strategy focused on reliable stock and predictable delivery. The compact, durable design is suitable for workbenches, tool trolleys and inspection kits, and the clearly specified dimensions simplify inventory and tool lists. Metav’s position as a dependable supplier underlines the product’s role in democratising precision: high-quality measuring aids available to small shops and large workshops alike, backed by a documented supply chain and customer base that values consistency. Contact Metav Werkzeuge for availability, technical details and to secure the Metav IndustryLine 600 mm anodised workshop ruler, SKU M203.054. Technical Data Article number: M203.054 GTIN: 4054469183374 Manufacturer: Metav IndustryLine Facts Length: 600 mm Width: 50 mm Thickness: 5 mm Weight: 0.2 kg Special features Material: Anodised aluminium Scale: mm division Finish: Non-reflective (matt) Category: Rulers ECLASS: 21170122 FAQ What material is the rule made from? The rule is manufactured from anodised aluminium, which delivers corrosion resistance and a durable surface suited to everyday workshop use. How precise is the printed scale? The printed mm scale provides clear graduations for general-purpose measuring and marking; the format is intended for rapid length checks rather than traceable calibration-required measurement tasks. Is the surface reflective under typical workshop lighting? No; the ruler has a non-reflective, satin finish to reduce glare and improve legibility in bright or angled light conditions. Can the rule be used for scribing and layout on metal and wood? Yes; the straight, rigid profile and clear mm division make it suitable for scribing, marking and layout operations on common workshop materials. Which SKU should be referenced when ordering? Reference SKU M203.054 or the GTIN 4054469183374 when enquiring about this anodised 600 mm workshop ruler. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600mm Workshop Rule 40mm Wide 5mm Thick Bevelled Edge Ungraduated, Special Steel - Metav IndustryLine
Combine the 600 mm working length, the ground special steel construction and the faceted edge to secure reliable alignment and long service life; order the workshop ruler directly via Metav Werkzeuge or consult our advisors for further specifications. Workshop ruler M214.723 — 600 × 40 × 5 mm, faceted, ground special steel (Metav IndustryLine) The Workshop ruler M214.723 is an ungraduated, heavy-duty straightedge designed for layout, marking and alignment tasks in busy workshops and toolrooms. 600 mm working length for large-format layouts Ground special steel for long-term durability Faceted edge for reliable alignment and stop Solid 5 mm thickness for stiffness and stability Stable reference over long runs for consistent layout results The 600 mm length combined with a 5 mm thickness and 40 mm face provides a rigid reference that resists bending during marking and scribing. Manufactured from ground special steel, the bar keeps a flat, wear-resistant surface that secures repeatable contact across its full length. The listed mass of 1.2 kg gives the rule useful inertia when used as a straightedge or clamping reference, reducing the tendency to shift during scribing or transfer operations. Faceted edge and ungraduated design for versatile workshop use A faceted edge simplifies alignment against stops and faces, enabling quick transfer of edges and concise layout lines without distraction from scale markings. The absence of graduations makes the bar particularly suitable as a precision straightedge, layout rule or inspection reference where a clean, uninterrupted bearing surface is required. The ground finish further minimises burrs and ensures a secure seating against workpieces and fixtures, supporting accurate marking on steel, wood or composite materials. Engineered for everyday industrial demands with Metav quality control This solid workshop rule is built for repetitive use in fabrication, maintenance and jig-making environments where durability and a reliable datum are essential. The ground special steel construction balances toughness with dimensional stability so that routine handling, clamping and light impacts do not compromise its reference function. Supplied under the Metav IndustryLine, the component benefits from the company’s quality filter in Emmerich, which supports consistent availability and traceability for professional buyers. Secure the Metav IndustryLine workshop ruler through Metav Werkzeuge for dependable layout precision; contact our advisors at info@metav-werkzeuge.com or call +49 2822 7131930 for technical clarifications and ordering support Technical data Article number: M214.723 GTIN: 4054469109626 Tariff number: 90178010 Weight: 1.2 kg Material: ground special steel Facts Length: 600 mm Width: 40 mm Thickness: 5 mm Special features Faceted edge Without graduations (ungraduated) Ground surface finish Category: rulers (Lineale) Brand: Metav IndustryLine FAQ Is the ruler graduated for direct measurement? The workshop ruler M214.723 is supplied without graduations; it is intended as an ungraduated straightedge and layout tool rather than a scale for direct measurements. What material and finish does the bar have? The bar is made of ground special steel, which provides a wear-resistant, flat bearing surface suitable for layout and marking tasks. Is this ruler suitable for heavy workshop use? Yes, the construction and 5 mm thickness deliver stiffness and robustness for daily use in fabrication, maintenance and jig-making applications. Can the ruler be used as a reference for clamping or fixturing? The faceted edge and rigid profile make the M214.723 suitable as a datum for alignment, clamping and transfer operations where a straight, unmarked bearing is required. What is the exact product identifier for ordering? Order under SKU M214.723 / GTIN 4054469109626; the item is part of the Metav IndustryLine range and is supplied via Metav Werkzeuge. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
600mm Workshop Rule With Bevel And Millimetre Scale, Ground Special Steel - Metav IndustryLine
Take advantage of a robust measuring tool that combines ground special steel, a chamfered edge and clear millimetre graduation for reliable layout and verification in metalworking. Order the workshop ruler directly via Metav Werkzeuge or consult our specialists for application advice. Workshop ruler M214.733 — 600 x 40 x 5 mm, chamfered, ground special steel The Workshop ruler M214.733 is a heavy-duty steel rule designed for precise linear measurement and layout work in general fabrication and metal workshops. Durable ground special steel construction Precise millimetre graduation for clear readings Chamfered edge for accurate alignment and reduced burrs Solid 600 x 40 x 5 mm profile for workshop tasks Lasting accuracy from robust construction The ruler is manufactured from ground special steel, a choice that gives a stable, wear-resistant measuring edge and consistent flatness over time. The 600 x 40 x 5 mm cross-section provides a stiff profile that reduces flex and improves repeatability when marking or checking parts on a bench. Thanks to the ground finish, reflections are minimised and the scale stays legible under workshop lighting, ensuring reliable results across routine inspection and layout tasks. Clear graduations and practical edge geometry A straight, chamfered edge with millimetre graduation supports quick, unambiguous measurements and clean scribing along the line. The chamfer (facetted) edge helps to avoid catching on burrs and makes it easier to align the rule against edges and faces, which speeds up marking operations and reduces the chance of misalignment. The combination of readable divisions and a low‑distortion surface reduces measurement uncertainty in everyday tasks. Designed for the workshop environment The overall format and finish suit hard‑wearing use in assembly, maintenance and general fabrication. The tool’s mass and profile give it a stable hand feel during layout work and it integrates easily with other measuring aids and marking tools. As part of a workshop kit, the ruler supports efficient workflows by providing a dependable reference for straightness, length checks and scribing operations without requiring specialised fixtures. For project-specific advice or to secure the Workshop ruler M214.733 from Metav IndustryLine for routine layout and inspection tasks, contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com Technical Data Article number: M214.733 GTIN: 4054469109695 Brand: Metav IndustryLine Category: Lineale Material: Ground special steel Facts Length: 600 mm Width: 40 mm Thickness: 5 mm Weight: 1.0 kg Special features Chamfered edge (facetted) Millimetre graduation Ground surface finish Workshop ruler for layout and inspection FAQ What is the exact length and cross section of the ruler? The Workshop ruler M214.733 has a length of 600 mm with a cross section of 40 x 5 mm, providing a stiff profile suitable for workshop layout. Which material is used for this ruler and why does it matter? The M214.733 is made from ground special steel; the ground finish improves flatness and legibility, which helps maintain measurement reliability in daily use. Is the scale readable in standard workshop lighting? Yes, the millimetre graduation combined with the ground surface of the Workshop ruler M214.733 delivers clear contrast and low reflection for easier reading during marking and inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
750mm Assembly Ruler Double-T Aluminium‑Magnesium Alloy Grade 0, 60mm Height, 30mm Width, HV80 Hardness - Metav IndustryLine
The combination of Grade 0 flatness and a lightweight Aluminium‑magnesium alloy body ensures consistent alignment results and easy handling on the shop floor. Benefit from precise 0.005 mm flatness and parallelism for reliable fixture set-up; order the straightedge directly via Metav Werkzeuge or contact the technical team for application advice. Assembly straightedge M214.743 — 750 × 60 × 30 mm, AlMg alloy, Grade 0 (Metav IndustryLine) A precise Assembly straightedge M214.743 designed for flatness-critical alignment and repeatable fixture set-up in industrial metrology and assembly work. 750 × 60 × 30 mm aluminium-magnesium alloy Grade 0 flatness 0.005 mm tolerance Hardness HV 80 for wear resistance Lightweight design at 1.2 kg for handling Consistent alignment through measurable precision The straightedge delivers repeatable positioning thanks to its Grade 0 specification, with both flatness and parallelism rated at 0.005 mm. These measurable tolerances make the tool suitable for quality control and alignment tasks where traceable reproducibility reduces rework and saves production time. The strict geometric specifications support fast decision-making in inspection steps and help to maintain a defined reference across multiple set-ups. Lightweight alloy construction with industrial endurance Constructed from an Aluminium‑magnesium alloy, the beam balances low mass and structural rigidity for workshop use. At 1.2 kg, the component is easy to manoeuvre while the surface hardness of HV 80 provides resistance to wear in regular handling. The stated yield strength (110 kg/mm²) and tensile strength (47 kg/mm²) indicate a material chosen for dimensional stability under typical assembly loads, offering longevity without significant weight penalties. Practical benefits for fixture set-up and inspection With overall dimensions of 750 × 60 × 30 mm, this straightedge spans medium-format assemblies and fixturing tasks while remaining compact enough for frequent repositioning. The design supports rapid visual and tactile checks when establishing datum lines or checking mating surfaces. In environments where consistent reference geometry shortens alignment cycles, the tool functions as a dependable workshop standard and integrates well into existing inspection procedures. Contact Metav Werkzeuge today to discuss how the Assembly straightedge M214.743 fits into current set-ups or to request detailed specifications and procurement assistance from the Emmerich team Technical data Article number: M214.743 GTIN: 4054469184517 ECLASS: 21170122 Core specifications Dimensions: 750 × 60 × 30 mm Weight: 1.2 kg Flatness: 0.005 mm Parallelism: 0.005 mm Hardness: HV 80 Features & materials Material: Aluminium‑magnesium alloy Yield strength: 110 kg/mm² Tensile strength: 47 kg/mm² Category: Lineal / measuring device FAQ What applications is this straightedge suited for? The Assembly straightedge M214.743 is suitable for fixture alignment, reference checks and flatness verification in machining and assembly tasks where Grade 0 tolerances are required. Does the product include a calibration certificate? The product description does not state calibrated delivery; calibration options and certificates can be provided on request by Metav Werkzeuge for shop-floor or laboratory requirements. How does the alloy construction affect handling and durability? The Aluminium‑magnesium alloy combines low weight with good stiffness, enabling simple handling at 1.2 kg while the HV 80 surface hardness helps resist wear during routine use. Can the straightedge be used as a reference for inspection gauges? Yes, the specified 0.005 mm flatness and parallelism make the tool suitable as a working reference for comparative checks and set-up verification in quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75mm Hairline Gauge Stainless Steel, Hardened, Ground And Lapped, DIN 874/00 - Metav IndustryLine
Take advantage of a compact, workshop-ready solution that combines DIN 874/00 conformity with fully hardened, ground and lapped INOX stainless steel for consistent layout and vernier tasks; order directly via Metav Werkzeuge or consult the specialists for application advice. Hairline ruler INOX 75 mm DIN 874/00 — compact precision hairline ruler (Metav IndustryLine) A Hairline ruler INOX 75 mm DIN 874/00 designed for fine mechanical measurement and layout work where a slim, corrosion‑resistant straight edge and clear hairline definition are required. Hardened, ground and lapped INOX steel Compact 75 mm length for fine work Conforms to DIN 874/00 Precision where small dimensions matter The compact straight edge is manufactured from INOX stainless steel that is hardened, ground and lapped, producing a stable reference surface with minimal runout. The short length and refined finish make this hairline gauge ideal for tasks that demand repeatable marking and inspection in restricted spaces. Because the metallic surface is corrosion‑resistant, the tool maintains accuracy over time with straightforward cleaning, giving a reliable baseline for layout, comparison and vernier measurements in workshops and inspection benches. Why the DIN standard and surface treatment improve results Conformity with DIN 874/00 signals a measured approach to dimensional and surface tolerances; this standard ensures the hairline edge meets expected flatness and finish criteria for workshop use. The combination of surface lapping and grinding reduces microscopic irregularities that could otherwise shift a mark or reading. In practice, this means fewer rechecks, reduced scrap and faster throughput on small assemblies where the definition of the hairline itself becomes the decisive factor. Designed for everyday workshop integration A short straight edge excels in repeatable, one‑hand layout operations and precision marking on small housings, shafts and fittings. The compact format fits in tool trays and pockets, simplifying workflow by keeping a precision reference at hand. For production environments that value predictable processes, this type of instrument supports quick visual checks and fine adjustments without the overhead of larger metrological equipment. As a practical benefit, the rust‑resistant steel eliminates common concerns about surface deterioration that can compromise markings and measurements. Contact Metav Werkzeuge to discuss the Metav IndustryLine INOX hairline ruler and secure the compact precision tool tailored to fine measurement tasks Technical data SKU: M214.119 GTIN: 4054469106670 Brand: Metav IndustryLine Tariff code: 90173000 Core measurements Length: 75 mm Standard: DIN 874/00 Special features Material: INOX stainless steel, hardened, ground and lapped Finish: precision lapped surface for defined hairline Application: layout, marking and vernier comparison tasks FAQ What sizes are available for similar hairline rulers? This item is the 75 mm version; comparable products from the same range are typically offered in longer lengths for larger assemblies. Is the surface resistant to corrosion? Yes, the INOX stainless steel construction gives the hairline ruler good corrosion resistance while preserving the precision finish. Can this ruler be used for vernier or comparative measurements? The hardened and lapped reference edge is suitable for vernier comparisons and layout checks where a defined straight edge is required. What does DIN 874/00 guarantee for this tool? Compliance with DIN 874/00 indicates adherence to accepted flatness and finish standards for small straight edges, ensuring consistent performance for shop use. Is the product suitable for use in assembly jigs and fixtures? The compact size and stable hardened surface make the instrument well suited for fixture setup and fine alignment tasks in small assemblies. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75mm Hairline Ruler Blackened Tool Steel, Hardened Ground And Lapped, DIN 874/00 - Metav IndustryLine
Take advantage of a compact 75 mm format combined with DIN 874/00 standardisation and a fully hardened, ground and lapped tool-steel construction for reliable layout and repeatable reference lines; order the hairline ruler directly via Metav Werkzeuge or ask our consultants if needed. Hairline ruler M214.019 — 75 mm, hardened tool steel (DIN 874/00) A hairline ruler intended for precise scribing and inspection tasks in metalworking and fine assembly, offering a durable reference edge in a compact format. DIN 874/00 standardised measuring rule Fully hardened, ground and lapped Compact 75 mm length for fine work Blackened finish for corrosion resistance Reliable standard compliance for repeatable markings The DIN 874/00 conformity ensures that the rule serves as a stable reference for layout and inspection tasks, reducing variability when transferring measurements. With a 75 mm usable length and a fully hardened, ground and lapped surface, the tool provides a flat, wear-resistant edge that maintains accuracy over many cycles. This construction minimises burr formation and keeps scribed lines consistent, which is essential for quality control in small-part production. Robust finish and compact handling for workshop use A blackened finish gives the rule improved resistance to corrosion while reducing surface reflections during marking operations. The compact dimensions make the instrument easy to position and handle in confined spaces, enabling steady, precise work on small components. The combination of hardness and surface finishing reduces the need for frequent replacement, supporting continuous operation in busy workshops and inspection benches. Practical applications and dependable build quality Ideal for precision marking, visual inspection and fine mechanical assembly, the hairline ruler is suited to tool rooms, maintenance shops and electronics assembly where a reliable reference line is required. The hardened and lapped edge resists deformation, supporting repeatable layout work and contributing to faster inspection cycles. Traceability is supported by the clear labelling and standard conformity, helping integrate the tool into routine quality processes. Contact Metav Werkzeuge for procurement advice or to request the Metav IndustryLine hairline ruler M214.019 for your workshop Technical data Article number: M214.019 GTIN: 4054469106076 Standard: DIN 874/00 Length: 75 mm Material: tool steel, fully hardened, ground and lapped, blackened Facts Customs tariff number: 90173000 eClass: 21170120 Special features Category: rulers Finish: blackened (schwarzbruniert) Construction: hardened, ground and lapped surface Intended use: precision scribing and inspection FAQ What is the usable length of this hairline ruler? The ruler provides a 75 mm measuring edge, suitable for fine marking and short-range inspection tasks. Is the edge durable enough for repeated scribing? Yes. The fully hardened, ground and lapped tool-steel edge is designed to resist wear and maintain a reliable reference over prolonged use. What standard does the ruler comply with? This instrument is manufactured to DIN 874/00, ensuring standardised form and function for workshop layout and inspection. Does the finish protect against corrosion? The blackened finish offers improved resistance to surface corrosion and reduces glare during marking operations. Can this ruler be used for precision assembly work? Yes. Its compact format and wear-resistant edge make it well suited to precise assembly and inspection tasks in tool rooms and fine-mechanical workshops. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8 m Twist Tape Measure 25 mm Steel Tape With Belt Clip And Lock, Class II - Metav IndustryLine
Take advantage of the compact 8 m measuring range, robust 25 mm steel tape and secure positive-lock for dependable daily use; lightweight handling and a belt clip keep the measure at hand on the workfloor. Order the instrument directly via Metav Werkzeuge or consult the specialists for specification advice. Pocket tape measure M203.112 — 8 m x 25 mm, ABS case, belt clip (Metav IndustryLine) A pocket tape measure that combines an 8 m reach with a sturdy ABS housing and a belt clip for workshop and trade applications 8 m measuring range, 25 mm steel blade ABS impact-resistant case with belt clip Positive-lock mechanism for secure measurements Accuracy Class II suitable for workshop use Reliable measuring performance for everyday workshop tasks The compact design delivers a consistent measuring range of 8 m on a 25 mm wide steel tape, balancing reach and stability for routine site and workshop work. The instrument meets Class II accuracy, which permits reliable results for general trade and construction tasks while conforming to recognised measuring standards. The tape’s blade geometry and material reduce flutter on extensions, enabling faster, more repeatable readings and fewer retakes to keep processes efficient. Practical handling and durable construction for frequent use Housed in an ABS case, the measure resists impacts and abrasion typical in workshops and on building sites; the belt clip ensures the tool is immediately available without occupying pockets. A positive-lock system secures the blade during layout or transfer measurements, preventing slip and reducing rework. With a net weight of approximately 0.4 kg, the unit is light enough for handheld convenience yet robust enough to withstand everyday handling, making it a dependable companion for technicians and tradespeople. Where this measure adds value in workflows This tape is ideal for carpentry, general building, fitting and metalworking where quick, repeatable linear checks are required. The steel tape suits indoor and sheltered-site use and is compatible with common workshop practices such as marking, templating and quick verification of component dimensions. Its compact form supports mobility across job locations, while the lock and blade stiffness reduce measurement error, supporting smoother production or installation sequences. Contact Metav Werkzeuge today for detailed technical advice or to arrange fast supply from our Emmerich warehouse — our consultants will help specify the right measuring tools for the task at hand. Technical data Article number: M203.112 GTIN: 4054469181721 Label: Pocket tape measure, EC Class II, 8 m x 25 mm, ABS case, lock + belt clip Facts Measuring range: 8 m (0–8000 mm) Blade width: 25 mm Weight: 0.4 kg Accuracy: Class II Special features Material: steel tape ABS case Belt clip Positive-lock mechanism FAQ What accuracy can be expected from this tape measure? The pocket tape measure M203.112 provides Class II accuracy, suitable for standard workshop and site measurements where repeatable results are required. Is the blade material suitable for professional use? Yes, the steel tape blade of the M203.112 is designed for regular trade and workshop applications and offers good stiffness for extended measurements. Does the measure include a locking mechanism? A positive-lock mechanism is fitted, enabling secure blade fixation during transfer and layout tasks to reduce measurement errors. How portable is the instrument for site work? Weighing about 0.4 kg and equipped with a belt clip, the measure is engineered for portability and quick access on site or in the workshop. Can this tape be used for exterior building measurements? The M203.112 is primarily intended for indoor and sheltered-site use; care is advised against prolonged exposure to harsh weather to preserve blade condition and accuracy. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
800 x 40 x 5 mm Workshop Rule With Chamfer, Unmarked, Hardened Ground Special Steel - Metav IndustryLine
Take advantage of the 800 x 40 x 5 mm profile and ground special steel construction for a robust marking and referencing tool in workshop layout and fabrication. The bevelled edge and ungraduated face provide a reliable guide for scribing and clamping, while procurement and advice are handled directly via Metav Werkzeuge. Werkstatt-Lineal 800 x 40 x 5 — ground special steel, bevelled edge (Metav IndustryLine) A Werkstatt-Lineal 800 x 40 x 5 designed as a heavy-duty workshop rule for precise alignment, scribing and routing tasks in metalworking and general fabrication. Ground special steel construction for flatness and durability Bevelled edge for clear scribing and guide work Plain, ungraduated face suitable for marking templates Consistent reference for layout and machining The long, flat profile of this workshop rule provides a dependable reference line for layout and machine set-up. The 800 x 40 x 5 mm dimensions combine reach with rigidity, reducing flex during use and improving repeatability when clamping against vices or machine fixtures. The ground special steel finish contributes to a stable contact surface and long-term flatness, which translates into fewer alignment errors and less rework in production environments. Emphasis on measurable stability supports quicker set-up times and predictable results. Designed for accurate scribing and clamping operations A bevelled edge on the rule creates a precise face for scribing, letting operators draw clean lines while maintaining a safe clearance for cutting tools. The intentionally plain, ungraduated face avoids visual clutter, making this tool ideal as a datum or template rather than a measuring instrument; it performs best when used in combination with calibrated gauges or micrometre systems for final inspection. This focused functionality supports efficient workflows: faster marking, secure clamping and reliable transfer of reference lines to workpieces. Built for workshop resilience and procurement clarity Manufactured from ground special steel, the rule offers wear resistance and a robust surface for repeated contact with scribes, squares and cutting edges. The simple, engineered form factor minimises failure modes and eases storage. As part of the Metav IndustryLine range, it benefits from centralised supply and quality control—an asset for purchasing departments that prefer consistent sourcing and dependable lead times. Traceability is supported by the article identifiers provided below, enabling straightforward inventory management. Choose the Metav IndustryLine workshop rule for dependable referencing in production — contact Metav Werkzeuge in Emmerich for procurement advice and delivery coordination via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M214.724 GTIN: 4054469109633 Tariff number: 90178010 ECLASS: 21170122 Facts Dimensions: 800 x 40 x 5 mm Category: Measuring instruments / Rulers File reference image available Special features Material: special steel, ground Bevelled edge for scribing and guidance Plain, ungraduated face for template work FAQ What applications suit this workshop rule best? The workshop rule M214.724 is suited to layout, scribing and clamping tasks in metalworking and fabrication where a flat, robust datum is required rather than a graduated measuring scale. Is the surface finish suitable for precision reference work? Yes. The ground finish on the special steel provides a stable, wear-resistant contact surface that supports repeatable referencing and alignment. Does the rule include graduations or markings? No. This product is supplied without graduations; its plain face is intended for use as a datum or template and for guiding scribing operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
800mm Precision Steel Ruler, Hardened Ground Lapped, Black Oxide Finish - Metav IndustryLine
Benefit from the combination of hardened tool steel, DIN 874/0 conformity and a blackened, ground and lapped blade to secure repeatable straightness references across workshop and inspection tasks; this robust 800 mm straight edge supports stable setup and reduces rework. Order the item directly from Metav Werkzeuge or consult their specialists for application advice. Hairline straight edge 800 mm (DIN 874/0) — Metav IndustryLine, hardened tool steel The Hairline straight edge 800 mm (DIN 874/0) is a hardened, ground and lapped tool-steel rule with a blackened finish, intended for accurate straightness and flatness checks in workshop and inspection environments. 800 mm hardened, ground and lapped blade Complies with DIN 874/0 tolerance standard Blackened finish reduces glare and corrosion Solid tool-steel construction for stability Reliable reference for inspection and layout work The straight edge serves as a stable reference line for inspection, scribing and machine set-up, offering conformity with DIN 874/0 so that results can be compared against a recognised tolerance class. Because the blade is ground and lapped, the surface presents a uniform contact face that reduces point loading and localised error; this improves repeatability when checking flatness or aligning components. The calibrated geometry of the edge minimises interpretation uncertainty during quality control tasks and supports faster decision making on whether a part meets specification. Robust construction that maintains accuracy over time Constructed from tool steel, fully hardened and finished by grinding and lapping, the blade resists wear and keeps its reference profile under frequent use. The blackened finish reduces glare under workshop lighting and offers a degree of surface protection against corrosion, while the substantial mass contributes to stability during measurement and layout tasks. These attributes reduce the need for constant rechecking and support a steady production flow by lowering the risk of measurement-induced rework. Practical benefits for the workshop and inspection bench At 800 mm length the straight edge strikes a pragmatic balance between reach and handling: long enough for many fixture and housing checks, yet manageable for single-person use. The weight and construction improve contact consistency on measured surfaces, aiding quicker assessments with dial indicators or visual hairline alignment. Supplied as a branded Metav IndustryLine tool, the item aligns with Metav’s approach to democratising precision: reliable quality, broad stock availability and straightforward integration into existing metrology routines help reduce supplier overhead and keep inspections on schedule. For precise straightness checks and robust workshop performance, request the Metav IndustryLine hairline straight edge (SKU M214.027) from Metav Werkzeuge or ask their consultants for assistance in choosing the right inspection reference for specific applications. Technical data SKU: M214.027 GTIN: 4054469106205 Tariff code: 90173000 Facts Length: 800 mm Weight: 6 kg Special features Material: Tool steel, fully hardened, ground and lapped Finish: Blackened (brunited) Standard: DIN 874/0 Category: Measuring instruments / Rulers FAQ What accuracy class does the straight edge meet? The hairline straight edge 800 mm meets the DIN 874/0 standard, providing a recognised tolerance class for straightness checks suitable for workshop inspection tasks. Is the tool suitable for heavy workshop use? Yes; the Metav IndustryLine hairline straight edge (SKU M214.027) is made from hardened tool steel with a ground and lapped surface designed for regular workshop inspection and layout duties. How should the straight edge be cared for to retain accuracy? Store the tool clean and dry, avoid knocks or drops, and protect the blade surface from grit. The ground and lapped finish benefits from light maintenance and careful handling to preserve the reference face. Can the straight edge be used with dial indicators or surface plates? The straight edge is intended as a reference for alignment and comparison work and pairs well with surface plates and dial indicators for visual and quantitative inspection routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
800mm Steel Straightedge, Hardened Ground And Lapped, DIN 874/0 - Metav IndustryLine
Take advantage of the combination of 800 mm working length, fully hardened stainless steel construction and DIN 874/0 accuracy for consistent alignment and inspection results. Order the hairline straightedge directly via Metav Werkzeuge or ask our consultants if needed. Hairline straightedge 800 mm — precision alignment rule (Metav IndustryLine) The Hairline straightedge 800 mm (INOX, DIN 874/0) is a hardened, ground and lapped stainless-steel straightedge designed for precise alignment, inspection and layout tasks in machine shops, inspection benches and toolrooms. 800 mm measuring length Hardened, ground and lapped stainless steel DIN 874/0 accuracy class Fine hairline for precise alignment Accurate reference for alignment and inspection A straight and stable reference speeds up inspection and reduces rework. Built to DIN 874/0, the instrument provides a defined tolerance class for straightness and flatness, making it suitable as a workshop reference for alignment checks and comparative inspection. The integrated hairline enables fine visual alignment against edges and surfaces; when used on machine beds, jigs or component faces it simplifies set‑up tasks and shortens inspection cycles, which improves throughput and reduces downtime. Robust construction for long service life Material selection and finishing determine longevity in a busy workshop. The bar is made from stainless steel, fully hardened, then ground and lapped to deliver a wear‑resistant, dimensionally stable surface that resists deformation during handling. The mass of the tool contributes to a stable contact against workpieces, so fewer rechecks are necessary and handling becomes more predictable. Corrosion resistance and surface finish preserve the reference quality, lowering maintenance effort and extending service intervals. Practical identification and workshop integration Clear identification and compatibility ease procurement and inventory control. Identifier details such as SKU M214.127 and GTIN 4054469163260 simplify ordering and stockkeeping; the tariff code supports freight and customs handling. The tool is intended for precision layout, machine alignment and quality inspection in industrial environments, where a durable straight reference improves measurement repeatability and operator confidence. The robust finishing also makes the piece suitable for regular use on inspection benches and in toolrooms without rapid wear. For reliable, workshop-grade alignment choose the Metav IndustryLine hairline straightedge and contact Metav Werkzeuge in Emmerich for order placement or technical guidance: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: M214.127 GTIN: 4054469163260 Tariff code: 90173000 Facts Length: 800 mm Weight: 6 kg Standard: DIN 874/0 Special features Material: stainless steel, fully hardened, ground and lapped Fine hairline for visual alignment Category: straightedge / rule FAQ What tasks is this straightedge best suited for? The hairline straightedge 800 mm is ideal for alignment, visual inspection and layout work on benches, machine beds and fixtures where a stable, straight reference is required. Is the straightedge corrosion resistant? Yes, the straightedge is made from stainless steel and is finished by grinding and lapping to provide long‑term corrosion resistance and surface stability. How does DIN 874/0 affect usability? DIN 874/0 defines the straightness and flatness tolerance class; the classification ensures predictable performance for workshop inspection and alignment tasks. Can the SKU and GTIN be used for procurement? The SKU M214.127 and GTIN 4054469163260 are provided for straightforward ordering, stockkeeping and logistics integration. Is this straightedge suitable for frequent workshop use? The hardened, ground and lapped construction makes the tool well suited to regular workshop use, offering wear resistance and stable reference quality over time. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
800mm Working Scale 40 x 5mm Graduations DIN 866/B, Ground Special Steel - Metav IndustryLine
Robust ground special steel construction, precise mm graduation and strict DIN 866/B conformity provide a stable 800 mm reference for workshop layout and inspection; order the working scale directly via Metav Werkzeuge or consult our technical advisors if further details are needed. Working scale 800 x 40 x 5 mm DIN 866/B – ground special-steel rule, mm graduation The Working scale 800 x 40 x 5 mm DIN 866/B, with mm division is a workshop-grade steel rule engineered for layout, measurement and quality-control tasks where a straight, wear‑resistant reference length is required. Ground special steel construction DIN 866/B standard compliant 800 mm measuring length Clear mm graduation for layout A dependable reference for precise workshop measuring The ground construction from special steel ensures a flat and wear‑resistant surface that maintains straightness under regular workshop use. With a full-length mm graduation and adherence to DIN 866/B, the rule functions as a reproducible reference for setting up jigs, checking part lengths and transferring dimensions. The 800 mm measuring span reduces the need for joins or repeated repositioning, which helps to cut cumulative measurement error in production and assembly environments. Built for durability and ease of interpretation A ground finish gives long service life and resists rapid wear, while the scale’s cross-section (40 x 5 mm) provides the stiffness required for handling without excessive flexing. The clear millimetre divisions simplify rapid visual reading during layout operations and routine checks. The construction and finish combine to reduce rework caused by ambiguous markings or surface degradation, supporting smoother shopfloor workflows and consistent results. Practical benefits that support productivity and quality Integrating a standardised, DIN‑compliant steel rule as a workshop datum shortens setup times and improves repeatability across workstations. The material choice and machining quality deliver a stable measuring tool that tolerates daily use without compromising reference accuracy. Backed by Metav’s position as a precision partner for industry and trade, this rule contributes to a predictable quality chain and dependable supply for busy machine shops and toolrooms. Contact Metav Werkzeuge to secure the Metav IndustryLine working scale with 800 mm measuring length and durable ground‑steel construction; technical consultants in Emmerich are ready to advise on compatibility with specific workshop tasks. Technical data Article number: M214.714 GTIN: 4054469109565 Tariff number: 90178010 Category: Measuring instruments › Rulers Facts Dimensions: 800 x 40 x 5 mm Weight: 1.6 kg Standard: DIN 866/B Measuring graduation: mm Special features Material: ground special steel Finish: precision ground surface Label: Arbeitsmaßstab 800 x 40 x 5 mm DIN 866/B, mit mm‑Teilung FAQ What materials is the rule made from? The working scale is manufactured from ground special steel, providing a wear‑resistant surface and stable reference length. Is the scale suitable for precision layout work? Yes. The Working scale 800 x 40 x 5 mm DIN 866/B, with mm division by Metav IndustryLine (SKU M214.714) is designed for workshop layout, inspection and repeatable measurement tasks. Which standard does the ruler comply with? Compliance with DIN 866/B ensures the scale’s graduation and overall dimensions meet established workshop ruler standards. What measuring range does the rule cover? The rule provides an 800 mm measuring length with millimetre graduation across its full span. Is the finish resistant to workshop wear? The precision ground surface increases wear resistance and supports clearer graduation readability over prolonged use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
800mm Workshop Rule 40mm Wide 5mm Thick Ground Special Steel - Metav IndustryLine
Combining a robust ground special steel construction with an 800 mm measuring length, the rule delivers a stable reference edge for layout and inspection tasks while resisting wear in daily workshop use. Order the tool directly via Metav Werkzeuge or consult our advisors for application guidance. Workshop rule M214.704 — 800 x 40 x 5 mm, ground special steel (Metav IndustryLine) The Workshop rule M214.704 is a durable straightedge intended for layout, inspection and machining support in general workshop and metalworking environments. 800 mm length for extended reach Ground special steel for stable straightness 40 mm width for secure guidance No chamfer for full-edge measuring Consistent reference for layout and inspection A long, rigid straightedge is the basis for reproducible layout and quick visual inspection. The 800 mm measuring length provides extra reach without sacrificing handling, while the ground special steel surface maintains a reliable straightness over time. In practice this means fewer rechecks during assembly or marking operations and a steady datum for scribing, aligning and checking flatness on medium-sized components. Construction that reduces measurement uncertainty The profile—40 mm wide and 5 mm thick—combines sufficient stiffness with manageable mass for single-person handling. The ground finish lowers surface irregularities that could affect contact, and the absence of a chamfer keeps the full edge available as a reference line. These design choices reduce operator-induced variation and support repeatable results during routine workshop tasks such as fixture set-up or part alignment. Practical handling, durability and workshop integration Made from special steel, ground, the straightedge stands up to knocks and abrasive workshop conditions while remaining serviceable for daily use. The geometry is suitable for guiding scribes, checking runout by eye and comparing against machine tables or component faces. Stored flat and cleaned after use, the tool sustains its performance; when integrated into a set of hand tools it becomes a go-to reference for both quick checks and more deliberate marking jobs. Why this tool makes sense for professional shops For workshops seeking a straightforward and durable reference edge, the combination of extended length and ground special-steel construction offers a cost-effective way to improve layout accuracy and decrease rework. The low-maintenance nature of the design keeps downtime to a minimum, while Metav IndustryLine distribution ensures availability from stock at the Emmerich site for reliable supply to industry and trade. Contact Metav Werkzeuge today for application advice and fast delivery from Emmerich — specify the Metav IndustryLine Workshop rule M214.704 to secure a rugged, long-length reference edge for your workshop. Technical data Article number: M214.704 GTIN: 4054469109497 Category: Rulers Customs tariff number: 90178010 Facts Dimensions: 800 x 40 x 5 mm Measuring length: 800 mm Width: 40 mm Thickness: 5 mm Special features Material: Special steel, ground Edge: No chamfer (full-edge reference) Suitable for layout, inspection and machining tasks Brand: Metav IndustryLine FAQ What is the best use for this workshop rule? The Workshop rule M214.704 is best used as a straight reference for layout, scribing and visual inspection on medium to large components where an 800 mm datum is helpful. Is the edge suitable for direct reference marking? Yes, the full-edge design without chamfer on the Metav IndustryLine rule allows direct use as a reference for scribing and alignment tasks. How durable is the material under workshop conditions? Constructed from ground special steel, the straightedge resists routine wear and maintains straightness when used and stored correctly. Can this rule be used for checking machine tables and large assemblies? The 800 mm length and stiff profile make the rule suitable for spot-checking flatness and alignment on machine tables and assemblies typical in general workshop use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
800mm Workshop Rule 40mm Wide, 5mm Thick, Bevel Edge, Millimetre Scale - Metav IndustryLine
The combination of a ground special-steel profile, a clear millimetre graduation and a chamfered edge ensures repeatable layout and reliable alignment in everyday workshop tasks; order the ruler via Metav Werkzeuge or consult our specialists for specification matching. Workshop ruler 800 x 40 x 5 mm — Metav IndustryLine, ground special steel, mm scale The Workshop ruler 800 x 40 x 5 mm is a sturdy, ground measuring profile for workshop and metalworking use, combining an easily readable millimetre graduation with a chamfered edge for precise marking and alignment 800 mm hardened, ground special-steel profile Precise millimetre graduation, easy reading Chamfered edge for reliable alignment Repeatable measurements with a rigid profile The ruler's geometry and finish make it suited to routine layout and inspection work where repeatability matters. The 800 mm length with a 40 x 5 mm cross-section provides a balance between reach and stiffness, reducing bend and vibration during handling. The ground special steel surface yields a flat, wear-resistant reference that preserves scale accuracy over time, so measurement routines stay consistent and rework is reduced. This stability supports quicker set‑ups on benches and in fixtures, improving throughput on repetitive tasks. Faster, clearer marking and checking on the shop floor A clear millimetre graduation allows for quick visual readings and accurate scribing without additional gauges. The chamfered edge simplifies edge alignment and prevents the rule from digging into softer workpieces while marking, which minimises measurement error during layout. For machinists and fitters, these features translate into fewer measurement steps and less time spent transferring dimensions, yielding tangible efficiency gains in daily processes. Built for longevity and easy integration into workflows The ground finish resists surface wear and simplifies cleaning after use, maintaining legibility of the scale even in demanding environments. The robust construction suits frequent handling and transport between machines and benches without rapid degradation. Supplied as part of the Metav IndustryLine, the product benefits from Metav’s quality control in Emmerich and its broad spare-part and accessory availability, supporting long-term, reliable use in professional workshops. Contact Metav Werkzeuge today for advice on integrating this Metav IndustryLine workshop ruler into production setups or for delivery details—call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M214.734 GTIN: 4054469109701 Dimensions: 800 x 40 x 5 mm Material: special steel, ground Tariff number: 90178010 Core measurements Length: 800 mm Width: 40 mm Thickness: 5 mm Special features Millimetre graduation Chamfered edge (facette) Ground surface finish Category: rulers (lineals) Brand: Metav IndustryLine FAQ What material is the ruler made from and why does it matter? The workshop ruler is made from ground special steel, a choice that offers a wear‑resistant, flat reference surface; this material maintains the integrity of the millimetre graduation for long service life. Is the scale suitable for precision layout work in a machine shop? Yes, the clear millimetre graduation and the rigid 40 x 5 mm profile make the ruler well suited for machine‑shop layout and general inspection tasks where repeatable alignment is required. Can the ruler be used for marking curved or irregular surfaces? The chamfered edge assists in aligning against straight edges and profiles; for curved or highly irregular shapes, the rule serves as a stable reference but additional fixtures or contour templates are recommended. Does the product come with calibration or a certificate? This workshop ruler is supplied in line with Metav IndustryLine quality procedures; specific calibration certificates are provided only when indicated in the product label or order details. What typical applications does this ruler cover? Common uses include layout and marking, quick dimensional checks on components, alignment of fixtures and jigs, and workshop inspection tasks where a robust, repeatable straightedge is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
810 mm Interior Wooden Case For 800 mm Gauge - Metav IndustryLine
Opt for a purpose-built wooden transport and storage solution with an interior length of 810 mm and a robust 6 kg construction to protect precision straight edges; order the wooden case directly via Metav Werkzeuge or consult our specialists for compatibility advice. Wooden case for 800 mm hairline rule (interior 810 mm) — Metav IndustryLine protective storage The Wooden case for 800 mm hairline rule provides secure storage and safe transport for precision rulers and straight edges used in workshops, inspection rooms and on-site measurement tasks. Solid wooden transport case, interior 810 mm Designed for 800 mm hairline rule compatibility Sturdy 6 kg construction for safe transport Protects precision instruments during transport and storage The purpose-made wooden case combines a precise internal clearance of 810 mm with a sturdy construction to prevent movement and impact damage to delicate straight edges. For instrument custodians and workshop managers this means fewer repair cycles and less downtime: a well‑fitted case reduces the risk of nicks, bends and surface wear that arise during handling. The robust build also aids repeatable stacking and secure placement in vehicles or storage racks, supporting a smoother material flow for quality‑driven operations. Integrates with the workshop to save time and reduce risk Designed specifically for compatibility with an 800 mm hairline rule, the case simplifies logistics and inventory handling in production and inspection environments. The clear sizing eliminates guesswork when assigning storage or tool trolleys, while the solid weight of 6 kg gives a reassuring feel of protection when moving items between benches or to measuring stations. This practical design supports efficient workflows and lowers the likelihood of accidental instrument damage, contributing directly to operational reliability and predictable inspection outcomes. Built and supplied with traceable quality and local support The wooden case is supplied by Metav IndustryLine from the Emmerich warehouse, reflecting a commitment to accessible precision. Local stockholding means shorter lead times and a single trusted source for replacements or matching accessories. Choosing this storage solution aligns with Metav’s promise to democratise precision: reliable products, transparent logistics and a broad range of compatible measuring equipment available from one partner. The combination of tailored fit, solid construction and dependable supply improves long‑term asset protection for any measurement arsenal. Contact Metav Werkzeuge for personalised advice and to reserve the wooden case held at our Emmerich warehouse. Technical data Article number: M214.027.K GTIN: 4061905450181 Label: Holzkasten für Haarlineal 800 mm innen 810 mm SKU: M214.027.K Facts Inside length: 810 mm Suitable for: 800 mm hairline rule Weight: 6 kg Special features Material: wood Purpose: transport and storage for hairline rules Category: Rulers FAQ Is this case suitable for an 800 mm straight edge? Yes. The Wooden case for 800 mm hairline rule is designed with an internal length of 810 mm to accommodate an 800 mm hairline rule with the necessary clearance for safe handling. Does the case provide adequate protection for precision surfaces? The wooden construction and precise internal clearance reduce movement and impact, so the Metav IndustryLine wooden case helps protect the straight edge surface during transport and storage. What are the shipping dimensions and weight to consider for logistics? The case has an internal length of 810 mm and a total weight of 6 kg; these figures support planning for handling and vehicle loading. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
LED Lighting for Rule Magnifier, Clip-On Attachment - Metav IndustryLine
Take advantage of the precise, even LED illumination and the clear compatibility with ruler magnifiers to improve scale readability and workflow reliability. Order the accessory directly via Metav Werkzeuge or consult our specialists for application advice. LED lighting for ruler magnifier — compact LED illumination for scale-reading tasks (Metav IndustryLine) The LED lighting supplies consistent, shadow-minimising illumination for precise readings on ruler-type magnifiers used in inspection and assembly tasks. Bright, uniform LED illumination Compatible with ruler magnifiers Low energy consumption and long life Improve measurement clarity with steady, glare-minimised light Even, reproducible lighting reduces reading errors when working with fine scales and magnified graduations. The LED module provides uniform illumination across the scale plane, so contrasts remain stable and parallax effects are easier to control. By supplying consistent light, the accessory supports faster, more reliable visual inspection and measurement work, which in turn reduces rework and inspection time. The design focuses on delivering an illumination that emphasises edge definition and scale markings without introducing hotspots or distracting reflections. Seamless integration into existing inspection setups The unit is designed for straightforward attachment to common ruler-style magnifiers and comparable scale-reading devices, making retrofit simple in production and laboratory environments. Quick installation translates into immediate operational benefits: measurements can continue with minimal downtime and without additional alignment tools. Compatibility with standard magnifier profiles ensures the lighting becomes part of the working process rather than an extra step, supporting efficient, repeatable measurement routines in both bench-top and mobile inspection situations. Durable performance for everyday workshop and quality-control use LED technology offers long service life and low power consumption, supporting continuous use in busy inspection areas while keeping maintenance intervals long. The robust construction withstands routine handling in metalworking and assembly environments, contributing to dependable uptime. Because the lamp provides stable illumination over time, calibration checks and visual verifications become more consistent, helping teams meet internal quality standards and maintain traceable inspection results with less variability. Contact Metav Werkzeuge for a tailored recommendation on the Metav IndustryLine LED lighting for scale magnifiers: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: M903.204 GTIN: 4061905449093 SKU: M903.204 Brand: Metav IndustryLine Product: LED lighting for ruler magnifier Facts GTIN: 4061905449093 SKU identifier: M903.204 Special features LED illumination technology Intended for ruler-type magnifiers Compact accessory for inspection and scale reading FAQ What does the LED lighting improve compared with ambient workshop light? The LED lighting provides uniform, directed illumination for scale readings, making graduations and edges easier to discern than with general ambient lighting; it is intended for use with ruler magnifiers and similar devices. Is the accessory compatible with all ruler magnifiers? Compatibility is intended for standard ruler-type magnifiers; the Metav IndustryLine LED lighting (SKU M903.204) is designed for straightforward attachment to common profiles used in inspection and measuring tasks. How does the LED lighting affect inspection efficiency? Consistent illumination reduces interpretation errors and speeds up visual measurements, supporting a more efficient inspection flow and fewer repeated checks. Who supplies this product and where can further technical questions be directed? The product is distributed by Metav IndustryLine; for specific fitting advice or technical details refer to Metav Werkzeuge using the contact details provided below Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Accurate checks with precision straightedges
Precision straightedges are high-accuracy measuring tools designed to verify flatness and straightness across surfaces. Available in several lengths and finished from durable metals, these instruments provide a simple, repeatable method for alignment and inspection in industrial settings.
How precision straightedges work and where they are used
A precision straightedge is laid against a surface to reveal deviations from true flatness or a straight line, with fine graduations enabling careful assessment of run-out and planar error. Typical applications include mechanical engineering, electronics, optics and microscopy, machine tool build and quality control, where reliable visual or feeler-gauge inspection prevents assembly issues and functional failure.
Key advantages that cut waste and speed up production
- high accuracy and stable construction reduce measurement uncertainty and help maintain production tolerances.
- stainless steel or other precision metals ensure long service life and corrosion resistance.
- fine graduations and etched scales allow precise readings and repeatable checks.
- various lengths suit bench work as well as larger components, shortening setup time.
- simple handling lowers inspection time and contributes to fewer rejects and rework.
Why Metav is the practical choice for precision straightedges
Metav combines decade-long expertise with a broad range of measurement tools, making it a pragmatic partner for workshop and production buyers. With over 48,000 customers and a catalogue exceeding 250,000 products, Metav operates from Emmerich as a quality filter for the european market, offering consistent availability and straightforward order processing. For those seeking a reliable source of precision straightedges and complementary measuring instruments, Metav’s range and technical information help select the correct specification for the intended inspection task.
In brief
Precision straightedges deliver fast, reliable assessments of flatness and straightness across industries, improving quality control and reducing scrap while being simple to use and maintain.
FAQ
What materials are precision straightedges typically made from?
Precision straightedges are commonly manufactured from stainless steel or other precision metals to ensure stability, wear resistance and longevity in industrial use.
In which industries are precision straightedges most valuable?
Precision straightedges are widely used in mechanical engineering, electronics, optics and microscopy, machine tool construction and general quality control where geometric accuracy is critical.
How is a precision straightedge used to check flatness?
Place the precision straightedge on the surface and inspect gaps visually or with feeler gauges; fine graduations and a straight reference edge make deviations from flatness evident for correction or further machining.
Are different lengths available for precision straightedges?
Yes, precision straightedges are offered in various lengths to match bench-top inspections as well as larger component checks, allowing selection of the most efficient tool for each application.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com