100-125mm Three-Point Internal Micrometer Self-Centring With Hardened Measuring Faces In Plastic Case - Metav IndustryLine
Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100-150mm Three-Point Inside Micrometer Colour Touchscreen Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of precise three-point measurement, wireless data output with USB, and full ISO 17025 calibration for dependable bore inspection and traceable results; order via Metav Werkzeuge or consult the specialists for application advice. Three-point internal micrometer — digital, 100–150 mm measuring range, Wireless + USB, Microtech Metrology The Three-point internal micrometer is a digital, workshop-ready instrument for repeatable bore and internal diameter checks from 100 to 150 mm, designed for production quality control and laboratory verification. ISO 17025 calibration certificate included Wireless and USB data output Colour 1.5" touchscreen display High repeatability: 0.004 mm accuracy Reliable measurement where it matters The instrument delivers consistent three-point measurement across bores, reducing orientation error and improving repeatability compared with single-point probes. With a specified accuracy of ±0.004 mm, the device supports quality control procedures that demand tight tolerances. The standard-sized measuring range classifies the tool for typical workshop and machine‑shop applications, offering a practical balance between reach and rigidity for medium-sized components. Fast data capture and traceability for production Equipped with Wireless and USB data outputs and a Colour 1.5" touchscreen, the device streamlines data acquisition and logging without manual transcription. The high-resolution reading (0.0001 mm) ensures fine increments are visible on the display, while digital output supports integration into measurement software or SPC workflows. This lowers administrative effort and helps maintain a clear audit trail for batch releases. Practical handling that reduces operator influence The included adjustment ring simplifies zeroing and routine checks, and the three-contact measuring head minimises tilting errors during insertion into bores. A measuring depth of 250 mm allows access to deeper cavities while preserving stability. These ergonomic and mechanical details reduce the effect of operator technique on the measurement result, improving reproducibility across shifts. Certified delivery and industrial readiness This micrometer is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate, making it immediately suitable for accredited quality environments. The combination of high accuracy, digital interfacing and certified calibration positions the instrument as a reliable tool for incoming inspection, in‑process checks and final acceptance testing. Contact Metav Werkzeuge for tailored advice and secure a certified Microtech Metrology three-point internal micrometer (SKU 133715010) with ISO 17025 calibration for your measurement process Technical data Article number: 133715010 GTIN: 4061905074295 Manufacturer: Microtech Metrology ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 100–150 mm Resolution (reading): 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 250 mm Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Calibration: ISO 17025 certificate included Special features Three-point internal measurement Adjustment ring included Digital operation for SPC integration Suitable for workshop and lab use Delivered calibrated for traceability FAQ Is this instrument supplied calibrated? Yes. The Microtech Metrology three-point internal micrometer (SKU 133715010) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. Which measurement range does the instrument cover? The device covers a measuring range of 100–150 mm, which places it in the standard class for workshop and machine‑shop bore inspection tasks. How are measurement results exported? Measurement data can be exported either wirelessly or via USB, enabling direct transfer into inspection software or SPC systems from the Microtech Metrology instrument. What resolution and accuracy can be expected? The display resolution is 0.0001 mm and the specified accuracy is ±0.004 mm, suitable for stringent dimensional checks in production control. Is the touchscreen suitable for use with gloves? The 1.5" colour touchscreen provides clear readout and simple menus; for glove operation, common shop gloves may limit sensitivity—repeatable results are maintained via the device’s stable mechanical design. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
10–12mm Three-Point Inside Micrometer Self-Centering, Supplied in Case - Metav IndustryLine
The combination of precise self‑centring contact, a compact 10–12 mm measuring range and robust carbide faces ensures fast, repeatable blind‑hole measurements with minimal setup. Order the instrument directly via Metav Werkzeuge or consult the team for application advice. Metav IndustryLine Three‑Point Internal Micrometre MS908.652 — self‑centring, 10–12 mm range The Three‑Point Internal Micrometre MS908.652 is a compact analogue micrometre designed for precise diameter measurement inside blind holes and small bores in the 10–12 mm range. Self‑centring three‑point contact Measuring range 10–12 mm Accuracy 0.004 mm Carbide measuring faces Reliable centring for blind‑hole measurement A three‑point contact ensures rapid and reproducible alignment in blind holes, reducing repositioning time and measurement scatter. The micrometre’s self‑centring mechanism automatically locates the bore centre, so the operator obtains a consistent contact geometry on each measurement. With a measuring span of 10–12 mm the instrument is tailored to micro components and small bores where repeatability and short setup times are essential, improving throughput in small‑part inspection tasks. Durable contact surfaces for longer service life The measuring faces are manufactured as carbide contacts to resist wear and preserve accuracy during frequent use. The unit’s analogue design gives a tactile feel and straightforward reading, paired with a fine adjustment capability to approach tight fits carefully. The compact body (length approx. 54.5 mm) is suited to constrained access, while a setting ring (size 10) is included for verification and quick zeroing, supporting stable traceability in routine quality checks. Practical workflow advantages and workshop integration This three‑point micrometre combines simple operation with technical reliability: measurements are quick, calibration checks are straightforward and the tool integrates easily into existing inspection benches. Classified in the Micro range (max. 10–100 mm), it fulfils typical needs of precision engineering, watchmaking and small‑component production where stiffness, reach and single‑hand operation must be balanced. Metav’s distribution ensures European stock and reliable delivery from Emmerich. Request application guidance or order details from Metav Werkzeuge for the Metav IndustryLine three‑point internal micrometre MS908.652 — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.652 Brand: Metav IndustryLine Category: Micrometres Type: Three‑point internal micrometre Measuring range: 10.0–12.0 mm Minimum range: 10 mm Maximum range: 12 mm Accuracy: 0.004 mm Length: 54.5 mm Setting ring: 10 Self‑centring three‑point contact Carbide (hard metal) measuring faces Analogue operation (nonius style) Suitable for blind‑hole bores FAQ How does the three‑point contact improve measurement in blind holes? The three‑point geometry of the MS908.652 centres automatically in a bore, giving a stable contact triangle that reduces wobble and improves repeatability compared with single‑point probes. What measurement accuracy can be expected from this instrument? The instrument is specified with an accuracy of 0.004 mm; in routine use this delivers repeatable diameter readings for small‑bore inspection tasks. Is the micrometre suitable for workshop use or only for laboratory conditions? Designed for practical workshop use, the robust carbide faces and analogue adjustment make the MS908.652 resilient to frequent handling while keeping measurement quality high. How is the instrument returned to zero or checked on site? A setting ring (size 10) is provided for quick verification and zeroing of the micrometre before inspection runs. Which components and applications benefit most from this micrometre? Small bores, precision fittings, watch‑ and micro‑mechanical parts and any blind‑hole diameters in the 10–12 mm range benefit from the compact form, self‑centring contact and carbide faces of the MS908.652. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10–12mm Three-Point Internal Micrometer Color Touchscreen, Wireless USB, ISO 17025 Calibrated - Microtech Metrology
Benefit from the combination of three-point contact stability, a colour touchscreen readout and ISO 17025 traceable calibration to secure reproducible internal measurements in the 10.0–12.0 mm range. Order the Three‑Point Internal Micrometer directly via Metav Werkzeuge or consult our specialists for integration advice. Three‑Point Internal Micrometer — digital instrument with Wireless + USB (Microtech Metrology) The Three‑Point Internal Micrometer is a precision instrument for stable internal diameter measurement in small bores, suitable for quality control and bench metrology in workshops and production. Three-point contact for stable internal measurements Colour 1.5" touchscreen for clear readouts Wireless and USB data output for traceable transfer Delivered calibrated to ISO 17025 with certificate Dependable accuracy where tight tolerances matter The instrument combines a three-point contact measuring head with a high‑precision mechanism to reduce runout and centring error, delivering an accuracy of ±0.004 mm across its measuring span. With a measuring range of 10.0–12.0 mm, this device is aimed at fine internal dimensions where repeatability and a low measurement uncertainty are decisive. The robust contact geometry and confirmed specification make it well suited to small‑bore inspection tasks in component finishing and final inspection workflows, supporting a rational decision process for integrating metrology into production control. Seamless data capture for quality documentation Digital measurement is presented on a Colour 1.5" touchscreen for fast reading and reduced interpretation errors; the unit also provides Wireless and USB data output for direct transfer into SPC systems or inspection software. Combined with the included calibration trace, this workflow supports rapid documentation and traceability. The instrument’s readable display and straightforward data export reduce process steps and the risk of transcription mistakes, promoting efficiency and error‑resilient quality reporting in serial inspection and laboratory environments. Practical design for everyday workshop use A compact measuring head with an extended measuring depth of 154 mm keeps handling comfortable while reaching into bores and recesses. A setting ring is included to simplify zeroing and periodic checks. Delivered fully calibrated to ISO 17025, the micrometer arrives with a formal calibration certificate, providing immediate confidence for compliance audits and internal quality routines. The combination of robust measuring geometry, clear digital feedback and certified calibration supports both operational ease and trustworthy results, reinforcing productive workflows and peace of mind in routine inspections. For traceable high‑precision internal measurement solutions from Microtech Metrology, contact Metav Werkzeuge for ordering and application support — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 133701210 GTIN: 4061905074202 Manufacturer: Microtech Metrology Numbers Measuring range: 10.0–12.0 mm Measuring depth: 154 mm Accuracy: ±0.004 mm Resolution/readout: 0.0001 mm Special features Digital display: Colour 1.5" touchscreen Data output: Wireless and USB Setting ring: included Delivered calibrated to ISO 17025 with certificate FAQ Is the instrument delivered with a calibration certificate? Yes. The Three‑Point Internal Micrometer from Microtech Metrology is supplied fully calibrated to ISO 17025 and includes the calibration certificate for traceability. What measurement range is covered by this micrometer? The device covers internal diameters from 10.0 to 12.0 mm and is designed specifically for high‑precision work within that span. How is measured data transferred to a PC or quality system? Measurement results can be exported via both Wireless and USB connections, enabling straightforward integration into inspection software and SPC workflows. What advantage does the three‑point contact offer? Three contact points centre in the bore automatically, reducing eccentricity and improving repeatability compared with two‑point methods, which is why this geometry is preferred for small‑bore internal measurements. Can the micrometer reach recessed bores? Yes. The instrument’s 154 mm measuring depth allows access to deeper internal features while maintaining the necessary measurement stability. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
12-16mm Three-Point Internal Micrometer Colour Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of high accuracy, wireless + USB data transfer and full ISO 17025 calibration with certificate for reliable measurements in precision workshops; order the three-point internal micrometre directly via Metav Werkzeuge or ask our consultants for tailored advice. Three‑Point Internal Micrometre – Digital internal measuring tool with wireless + USB and 1.5" colour touchscreen (Microtech Metrology) The Three‑Point Internal Micrometre is a compact digital instrument engineered for precise internal diameter measurement in small bores and precision components within the micro measurement category. *Digital display: 1.5" colour touchscreen *Wireless and USB data output *ISO 17025 calibrated with certificate *Measuring range 12–16 mm, 0.004 mm accuracy Accurate measurements for micro components Classified in the Micro category (suitable for very compact tasks), this instrument covers a measuring range of 12.0–16.0 mm, offering a practical reach for miniature assemblies and precision parts. The instrument combines a fine resolution of 0.0001 mm with a guaranteed accuracy of ±0.004 mm, which reduces measurement uncertainty and supports reproducible inspection results. Such precision is particularly valuable when inspecting small bores in sub‑assemblies where even slight deviations can affect fit and function. Traceable data capture and delivered calibration Designed for modern production environments, the micrometre provides wireless and USB connectivity for straightforward data transfer into inspection logs and SPC systems. The 1.5" colour touchscreen simplifies reading and setting adjustments on the shop floor, while the supplied setting ring ensures fast zeroing and repeatable reference points. The tool is supplied fully calibrated to ISO 17025 and includes a calibration certificate, enabling formal traceability and immediate use in processes that require accredited measurement results. Ergonomic handling that speeds up inspections The three‑point contact design centres measurement force, improving contact consistency inside bores and reducing operator‑induced variation. The compact format supports single‑hand operation in confined spaces and the intuitive touchscreen speeds routine checks, lowering cycle times and decreasing the likelihood of rework. The included setting ring and clear digital readout combine to make daily inspection routines both ergonomic and efficient. Integration into workshop quality routines With its digital outputs and compact form factor, the device integrates easily into existing inspection stations and handheld workflows. The substantial measuring depth of 230 mm provides versatility when accessing deeper bores or assemblies, while the three‑point mechanism ensures stable centring for reliable interior measurements. Together, these features support a consistent quality chain from initial inspection through to final acceptance. Contact Metav Werkzeuge in Emmerich for a suitability review or to request a quotation for this Microtech Metrology three‑point internal micrometre with ISO 17025 calibration; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 133701610 GTIN: 4061905074219 Manufacturer: Microtech Metrology ECLASS: 21170335 Facts Measuring range: 12.0–16.0 mm Resolution: 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 230 mm Special features Digital colour 1.5" touchscreen Data output: Wireless and USB Included setting ring ISO 17025 calibration with certificate Three‑point internal measuring spindle FAQ What bore sizes can be inspected with this instrument? The Three‑Point Internal Micrometre is designed for bores in the 12.0–16.0 mm range and is classified in the micro category for compact internal measurements. Is the micrometre delivered calibrated for traceability? Yes, the instrument is supplied fully calibrated to ISO 17025 and includes a calibration certificate for immediate traceable use. How are measurement results transferred to a PC or inspection system? Measurement data can be transmitted via the micrometre’s wireless interface or exported using the USB connection for integration into inspection logs. What level of precision can be expected during routine checks? Routine measurements with the Three‑Point Internal Micrometre offer a resolution of 0.0001 mm and an accuracy of ±0.004 mm, suitable for high‑precision shopfloor inspections. Does the tool include accessories for initial setup? The micrometre is supplied with an inclusive setting ring to establish a reproducible zero reference and support repeatable measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
12-16mm Three-Point Internal Micrometer Self-Centering, Plastic Case - Metav IndustryLine
Take advantage of the combination of compact design, repeatable self‑centring measurement and wear‑resistant carbide faces to maintain consistent bore quality in small components. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.653 — self‑centring three‑point head, carbide measuring faces (Metav IndustryLine) A Three‑point internal micrometer MS908.653 engineered for precise measurement of blind bores in workshop and quality‑control environments. Self‑centring three‑point measuring head Carbide measuring faces for wear resistance Precise range 12–16 mm with 0.004 mm accuracy Compact 80 mm body length for confined spaces Accurate measurements in confined bores The three‑point geometry provides a self‑centring effect that stabilises the measuring axis in blind holes, reducing eccentricity and improving repeatability. With a declared accuracy of 0.004 mm and a vernier reading increment of 0.005 mm, this analogue instrument delivers the fine mechanical resolution expected in micro‑component inspection. The design minimises operator variation by ensuring the measuring anvils expand symmetrically, which translates into faster decision‑making during incoming inspection or in‑process checks. Small format, specialist capability Classified in the Micro category (measuring range 12–16 mm), the tool combines a short 80 mm body length with a compact head that is easy to manoeuvre inside tight bores. The carbide measuring faces resist wear during repetitive use, extending the interval between maintenance cycles and preserving measurement integrity. An adjustment ring (size 16) allows repeatable pre‑settings for batch measurements, so set‑ups for small series or precision assemblies remain consistent without excessive rework. Built for blind‑hole tasks and straightforward handling Designed specifically for blind‑hole measurement, the three‑point micrometer eliminates the need for improvised measuring aids. Its analogue, non‑electronic construction favours robustness in workshop conditions and simplifies routine maintenance compared with electronic gauges. The combination of mechanical simplicity and the self‑centring head reduces measurement time and supports reliable dimensional control of bores used in bearings, housings and valve seats. Workshop integration and supplier confidence Metav IndustryLine supplies a practical measuring solution that fits established inspection routines and supports traceable quality processes. The instrument’s proven geometry and durable contact faces make it suitable for precision toolrooms and production lines where compact accuracy is required. For specification matching, calibration options and integration into existing quality workflows, Metav Werkzeuge acts as a single, reliable partner with rapid technical guidance and supply across Europe. Contact Metav Werkzeuge today for tailored technical advice and reliable supply of the MS908.653 three‑point internal micrometer via Metav Werkzeuge GmbH in Emmerich Technical data Article number: MS908.653 Brand: Metav IndustryLine Category: Messschrauben Facts Measuring range: 12.0–16.0 mm Measuring range (min): 12 mm Measuring range (max): 16 mm Body length: 80 mm Accuracy: 0.004 mm Reading increment: 0.005 mm Adjustment ring: 16 Special features Self‑centring three‑point head Carbide measuring faces Designed for blind‑hole measurement Analog/vernier design Compact micro‑class instrument FAQ What types of bores is this instrument intended for? This three‑point internal micrometer MS908.653 is designed for precise measurement of blind bores and internal diameters within its 12–16 mm range. How precise is the measurement and what resolution is readable? The instrument offers an accuracy of 0.004 mm with a vernier reading increment of 0.005 mm, providing fine mechanical resolution suitable for micro‑component inspection. Are the measuring faces durable for repetitive workshop use? Yes, the micrometer is fitted with carbide measuring faces to increase wear resistance during repetitive measurements and to maintain dimensional integrity. Is the micrometer suitable for small‑batch production set‑ups? Its compact 80 mm body and adjustment ring (size 16) enable repeatable pre‑settings, making the MS908.653 well suited to small series and frequent set‑ups. Can calibration or certification be arranged for this instrument? Calibration options and certificates can be arranged through Metav Werkzeuge; contact the supplier for available services and lead times. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12-20mm Three-Point Internal Micrometer Self-Centreing, 0.005mm Graduation, Supplied In Case - Metav IndustryLine
Benefit from self‑centring three‑point measurement, carbide measuring faces and a 0.005 mm vernier resolution to perform reliable blind‑hole checks in the micro range; order this precision set directly via Metav Werkzeuge or consult our experts for application guidance. Three‑point internal micrometer MS908.672 — 12–20 mm range, 0.005 mm vernier (Metav IndustryLine) The Three‑point internal micrometer MS908.672 is an analogue, self‑centring gauge designed for accurate measurement of blind bores within the micro range, where compact size and repeatable centring are essential. Self‑centring three‑point measurement Carbide measuring faces for wear resistance Resolution 0..005 mm for fine readings Precision where small tolerances matter This instrument is tailored to the micro range (12–20 mm), a segment where stiffness and compactness determine repeatability. The three‑point geometry automatically centres in blind bores, reducing operator alignment error and speeding up routine checks. With an analogue vernier reading at 0.005 mm, the gauge enables fine discrimination that supports tight tolerances without the complexity of digital systems. The compact format is especially useful in repair benches, toolrooms and micro‑assembly stations where space and manoeuvrability are constraints. Durable construction for frequent shop use Key contact surfaces are fitted with carbide measuring faces, providing excellent resistance to wear and abrasion and maintaining measurement integrity over many cycles. The instrument’s analogue vernier construction offers a robust, low‑maintenance solution for production environments. An adjustment ring (16) allows controlled settling of the measuring head, while the solid mechanical design minimises play and drift during repeated inside measurements. Practical set composition and extendibility Supplied as a set of two, the micrometers offer complementary coverage for daily shop workflows and quick changeover between inspection tasks. Extensions of 150 mm are available for deeper blind bore access, enabling the same measuring principle to be applied where reach is required. The compact set format reduces tool change time and simplifies storage for inspection kits on the shop floor. Application suitability and operator benefit Designed specifically for blind‑hole measurement, the gauge removes the need for complex adapters in many common tasks. The self‑centring action reduces the influence of operator alignment, while the fine vernier graduation supports confident pass/fail assessments in first‑operation inspection and incoming goods control. The analogue nature makes it straightforward to interpret results and integrate the device into established quality routines without training overhead. For tailored technical advice or to reserve this two‑piece precision set, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: MS908.672 Type: Three‑point internal micrometer Brand: Metav IndustryLine Designation: Three‑point internal micrometer Measurements Measuring range: 12.0–20.0 mm Resolution (reading): 0.005 mm Adjustment ring: 16 Set quantity: 2 pieces Special features Self‑centring three‑point system Carbide measuring faces Analogue vernier scale Suitable for blind‑hole measurement Extensions: 150 mm FAQ What measuring range does the instrument cover? The Three‑point internal micrometer MS908.672 covers a measuring range of 12.0–20.0 mm, placing it in the micro range suitable for fine mechanical work. Is this gauge suitable for blind‑hole inspection? Yes — the self‑centring three‑point design is specifically intended for blind‑hole (Sackloch) measurement and ensures reliable centring in such applications. How fine is the reading and how is it read? The analogue vernier provides a reading resolution of 0.005 mm; readings are taken from the vernier scale, offering precise manual measurement without electronics. Are the measuring faces robust enough for regular use? Measuring faces are made of carbide, giving the MS908.672 high wear resistance and long service life even under frequent shop use. Does the delivery include extensions and how many pieces are supplied? The delivered set comprises two instruments and includes extensions of 150 mm to extend reach into deeper blind bores. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125-150mm Three-Point Internal Micrometer Self-Centring With Hardened Measuring Faces, Supplied In Case - Metav IndustryLine
Take advantage of the combination of self-centring three-point contact, hardened measuring faces and a protective case for reliable, repeatable blind-bore measurement; order directly via Metav Werkzeuge or request advice from our technical consultants. Three-point internal micrometer MS908.664 — self-centring design, 125–150 mm (Metav IndustryLine) The Three-point internal micrometer MS908.664 is a precision instrument for accurate measurement of blind bores and internal diameters in machine shops and inspection benches Self-centring three-point contact Accuracy ±0.005 mm Hardened measuring faces Supplied in protective case Consistent concentric measurement where it matters The instrument’s self-centring three-point contact mechanism converts small radial differences into a single, centred datum, ensuring high repeatability during blind-bore checks. With a mechanical resolution and accuracy of ±0.005 mm, the device supports tight tolerance verification and process control for internal diameters. This level of precision is particularly useful when comparing series parts or validating internal fits, as the three-point geometry minimises eccentricity and reduces operator-induced variation. Robust construction for repetitive workshop use A durable construction and hardened measuring faces protect the contact points from wear and maintain measurement integrity over prolonged use. The analogue, mechanical drive reduces complexity and avoids battery dependence, making the tool suitable for routine quality inspections on the shop floor. The overall length of 145 mm gives the reach required for its measurement range while keeping the instrument compact enough for stable handling during repeated checks. Ideal balance of reach and stiffness for standard applications Classified in the standard range for internal measurement instruments (125–150 mm), this micrometer offers the best compromise between measuring reach and structural rigidity. That balance is critical in metalworking and fixture assembly, where longer tools can introduce deflection and shorter tools lack coverage. The design is optimised for blind bores, providing reliable access and reproducible contact even when full through-access is not available. Delivered protected and ready for transport The instrument is supplied in a protective case to safeguard measuring faces and the mechanism during transport and storage. Built for regular inspection cycles, it integrates easily into workshop tool sets and measurement benches; its analogue readout is simple to interpret and maintain, supporting efficient quality routines without complex electronic calibration procedures. Contact Metav Werkzeuge for tailored advice on the Metav IndustryLine three-point internal micrometer MS908.664 and to arrange procurement or technical specification support; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.664 Manufacturer: Metav IndustryLine Type: Three-point internal micrometer Feature: Self-centring Measuring range: 125–150 mm Length: 145 mm Accuracy: 0.005 mm Reading: 0.005 mm Mechanism: Analogue Delivery: protective case Measuring faces: hardened Suitable for: blind bores Numeric data Measurement range: 125–150 mm Maximum measurement: 150 mm Minimum measurement: 125 mm Accuracy/resolution: 0.005 mm Length: 145 mm SKU: MS908.664 Design and special features Self-centring three-point contact Hardened measuring faces for wear resistance Analogue drive for low maintenance Compact length for stable handling Supplied in protective case for transport Intended for blind-bore measurement FAQ What measurement range does the instrument cover? The instrument covers a measurement range of 125–150 mm, placing it in the standard workshop range suitable for many machine‑building and metalworking applications; refer to MS908.664 for exact limits. What accuracy and resolution are specified? The device offers an accuracy and reading resolution of 0.005 mm, enabling reliable checks against typical tight tolerance requirements. Is the design suitable for blind bores? Yes — the self-centring three-point contact is engineered specifically to measure blind bores with improved concentricity and repeatability. Are the measuring faces wear-resistant? The measuring faces are hardened to resist wear and maintain consistent contact geometry during repetitive inspection tasks. Is a protective case included? The instrument is supplied in a protective case to secure the micrometer during transport and storage. Is the micrometer digital or analogue? This is an analogue instrument with a mechanical drive and a direct, tactile measuring feel appropriate for workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150-175mm Three-Point Internal Micrometer Self-Centring, 0.005mm Accuracy, Replaceable Anvils, Delivered in Case - Metav IndustryLine
Take advantage of the combination of precise 0.005 mm reading, a self‑centring three‑point measuring mechanism and interchangeable measuring inserts to ensure reproducible internal measurements of blind bores in the standard workshop range. Order the instrument directly via Metav Werkzeuge or consult the Metav team for application advice. Three‑point internal micrometer MS908.665 — self‑centring, 150–175 mm range (Metav IndustryLine) The three‑point internal micrometer is an analogue internal measuring instrument designed for reliable measurement of blind bores and internal diameters in the workshop and production environment. Self‑centring three‑point design Measurement range 150–175 mm Analogue reading 0.005 mm resolution Hardened measuring faces, interchangeable insert Reliable metrology for internal diameters and blind bores The three‑point design offers consistent contact on the bore surface, enabling reproducible centring even in deep blind holes. With a measurement range of 150–175 mm this instrument fits the standard class of workshop metrology where reach, stiffness and one‑hand operation are required. The analogue scale provides a clear 0.005 mm reading and an equivalent stated accuracy, which supports routine quality checks and rapid go/no‑go decisions on the shop floor. Practical handling and application benefits for production Interchangeable measuring inserts allow adaptation to differing bore geometries without replacing the whole instrument, reducing downtime and consumable cost. The self‑centring mechanism simplifies alignment and lowers operator variability, which increases throughput and decreases rework. Designed for internal measurements including blind bores, the tool is particularly suitable for machine shops, toolrooms and maintenance departments that require straightforward, rugged measuring devices for repeat measurements. Construction and durability tailored to industrial use Hardened measuring faces reduce wear and maintain measurement fidelity over long service periods; the instrument’s analogue mechanics are engineered for robustness rather than electronic sensitivity. The combination of hardened anvils, an interchangeable insert system and solid construction ensures long‑term stability under workshop conditions and predictable measurement behaviour when performing internal diameter checks on components. Contact Metav Werkzeuge in Emmerich for tailored advice on the MS908.665 three‑point internal micrometer and to arrange delivery from stock — info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: MS908.665 Name: Three‑point internal micrometer (Dreipunkt‑Innenmessschraube) Manufacturer: Metav IndustryLine Core technical data Measurement range: 150–175 mm Reading / resolution: 0.005 mm Accuracy: 0.005 mm Length: 145 mm Analogue instrument Special features Self‑centring three‑point design Hardened measuring faces Interchangeable measuring insert Suitable for blind bores Analogue scale, workshop grade FAQ What measuring range does the MS908.665 cover? The MS908.665 three‑point internal micrometer by Metav IndustryLine covers a measurement range of 150–175 mm. How fine is the resolution and what accuracy is stated? The instrument provides an analogue reading with 0.005 mm resolution and a stated accuracy of 0.005 mm for routine workshop control. Is the design suitable for blind hole measurements? Yes, the three‑point geometry and self‑centring action of this micrometer make it particularly suitable for reliable measurements in blind bores. Can the measuring faces be replaced if worn? The MS908.665 features an interchangeable measuring insert system; hardened faces prolong service life and can be renewed through the insert mechanism. For which workshop tasks is this micrometer intended? The instrument is designed for internal diameter checks in machine shops, toolrooms and maintenance operations where robust, repeatable analogue measurement is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16-20mm Three-Point Internal Micrometer Self-Centering, Calibrated in Wooden Case - Metav IndustryLine
Take advantage of self‑centring three‑point measuring, compact dimensions and a finely graduated reading for consistent blind‑bore checks; the combination of repeatable centring, carbide measuring faces and analogue robustness supports efficient workshop workflows. Order the Three‑point internal micrometer directly via Metav Werkzeuge or ask our consultants if needed. Three‑point internal micrometer MS908.654 — self‑centring, 16–20 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.654 is a precision instrument designed for reliable measurement of blind bores in the 16–20 mm band, combining a three‑point contact head with a compact frame for confined spaces Self‑centring three‑point head Measurement range 16–20 mm Carbide measuring faces (HM) Delivered in protective case Precise bore measurement where space is limited The three‑point contact design ensures automatic centring inside a blind bore so that the measuring points engage evenly; this reduces eccentricity and improves repeatability compared with single‑point probes. With a defined measurement range of 16–20 mm the instrument falls into the micro class of calipers, making it especially suitable for fine mechanical tasks and small assemblies where controlled measuring force and stable contact geometry are decisive for consistent results. The compact geometry helps to keep torsion low and supports reproducible checks in confined geometries. Workshop‑grade contact surfaces and durability Hard‑facing on the contact surfaces gives dependable wear resistance: the carbide measuring faces resist abrasion in routine shop use and extend service life under frequent contact with metal workpieces. The micrometer’s analogue construction avoids batteries and electronic vulnerabilities, favouring simple maintenance and immediate readiness. Supplied in a protective case, the instrument is shielded during transport and storage, supporting reliable deployment across different production stations. Readability and measurement certainty The instrument provides a fine reading step alongside a verified accuracy that supports confident decision making. With a display increment of 0.005 mm and an assessed accuracy of ±0.004 mm, the micrometer allows precise comparative measurements and go/no‑go assessments in production and quality control. The three‑point mechanism shortens setup time for successive measurements and reduces correctional effort, which increases throughput without compromising measurement integrity. Applications, classification and practical benefit Classified as a micro‑range internal micrometer, the tool is suited to watchmaking, valve seats, small hydraulic components and other blind‑hole checks where a short, rigid measuring system is required. The self‑centring function removes an additional alignment step, while the robust contact material supports mixed workshop environments. As a compact analogue instrument it combines mechanical simplicity with measurement quality, making it an efficient choice wherever repeatable internal diameters must be verified. For procurement or technical advice on Metav IndustryLine measuring instruments, contact Metav Werkzeuge in Emmerich for personalised guidance and secure delivery from our European warehouse Technical data SKU: MS908.654 Manufacturer: Metav IndustryLine Type: Three‑point internal micrometer Core specifications Measurement range: 16–20 mm Accuracy: ±0.004 mm Reading increment: 0.005 mm Overall length: 80 mm Analogue operation Features and materials Self‑centring three‑point head Carbide measuring faces Suitable for blind‑hole bores Delivered in protective case Compact micro‑range instrument FAQ What measurement range does this instrument cover? The Three‑point internal micrometer MS908.654 covers a range of 16–20 mm, designed for precise checks in small blind bores. How accurate is the micrometer for production checks? The instrument offers an assessed accuracy of ±0.004 mm with a reading increment of 0.005 mm, allowing reliable comparative measurements on small components. Are the contact faces suitable for regular shop use? Yes, the measuring faces are made of carbide, providing increased wear resistance and extended service life in routine workshop conditions with the Three‑point internal micrometer. Is this micrometer suitable for very tight or confined bores? Its compact frame and self‑centring three‑point head make the tool especially suitable for confined blind‑hole applications where stable contact and low torsion are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
175-200mm Three-Point Internal Micrometer Self-Centring, Interchangeable Anvils, Supplied in Case - Metav IndustryLine
Take advantage of the self‑centring three‑point contact, the 175–200 mm measuring range and the proven 0.005 mm accuracy to ensure reliable blind‑hole checks in routine inspection. Order the instrument directly via Metav Werkzeuge or ask the consultants for application advice. Three‑Point Internal Micrometer (MS908.666) — Self‑centring, 175–200 mm range; 0.005 mm accuracy Three‑Point Internal Micrometer (MS908.666) is a mechanical measuring instrument designed for precise measurement of blind holes in the standard workshop range. Self‑centring three‑point contact system Measuring range 175–200 mm High accuracy 0.005 mm Interchangeable measuring anvils Reliable centring for blind‑hole measurement The self‑centring three‑point contact design guarantees consistent alignment with the bore axis, reducing operator‑dependent variance during inspections. With a measuring range of 175–200 mm, this instrument falls into the standard class for workshop metrology: it combines sufficient reach with manageable stiffness for repeatable checks on housings and medium‑sized components. The mechanical, analog construction gives direct tactile feedback when seating the contacts, which supports quick decision‑making on the shop floor and lowers cycle time for routine checks. Accurate results with carbide measuring faces Equipped with carbide measuring faces, the gauge provides wear resistance where contact durability matters most. The specified accuracy of 0.005 mm positions the instrument for high‑precision internal measurement tasks where sub‑hundred‑micrometre reproducibility is required. This level of accuracy is communicated as a clear, quantifiable benefit: fewer reworks, more reliable acceptance testing and better conformity with drawing tolerances during incoming or in‑process inspections. Adaptable anvils for different bore conditions Interchangeable measuring anvils increase the micrometer’s versatility: the exchangeable heads allow adaptation to varying bore geometries and surface finishes without sacrificing the calibration baseline. For workshops that encounter a range of blind‑hole diameters, the ability to switch measuring faces minimises downtime and reduces the need for multiple dedicated gauges, thereby improving operational efficiency and tool inventory management. Robust, workshop‑ready mechanical design The analogue mechanism with a precise reading increment of 0.005 mm is robust and straightforward to maintain in industrial environments. The solid mechanical construction suits regular use in inspection benches and quality departments where resilience and uncomplicated operation are priorities. The compact feel combined with the instrument’s length makes it practical for ergonomic handling during repeated measurements, supporting consistent measurement practice and traceable results. For precise blind‑hole inspections, contact Metav Werkzeuge to discuss the Three‑Point Internal Micrometer MS908.666 and its interchangeable anvils for seamless integration into existing inspection routines. Technical data Article number: MS908.666 Product type: Three‑point internal micrometer Brand: Metav IndustryLine Facts Measuring range: 175–200 mm Minimum range: 175 mm Maximum range: 200 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 145 mm Operation: Analog Special features Self‑centring three‑point contact Interchangeable measuring anvils Carbide measuring faces Suitable for blind‑hole measurement Mechanical design for workshop use FAQ What measuring range does the instrument cover? The Three‑Point Internal Micrometer MS908.666 from Metav IndustryLine covers a 175–200 mm measuring range. How precise is the three‑point internal micrometer? The gauge delivers an accuracy of 0.005 mm, offering high repeatability for internal bore checks. Can the measuring faces be changed for different bores? Yes, the instrument features interchangeable measuring anvils, allowing adaptation to varying bore geometries without replacing the whole tool. Is the micrometer suitable for blind‑hole measurements? Designed specifically for blind‑hole (sackloch) inspection, the self‑centring three‑point design ensures reliable centring in such applications. What construction ensures long service life in the workshop? The MS908.666 uses carbide measuring faces and a robust analogue mechanism to withstand frequent use in industrial inspection environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20-25mm Three-Point Internal Micrometer Self-Centring, Plastic Case - Metav IndustryLine
Take advantage of the combination of self‑centring, carbide measuring faces and high repeatability for reliable blind‑hole inspection; the compact 20–25 mm range is ideal for fine mechanical and precision engineering tasks. Order the instrument directly via Metav Werkzeuge or request specification advice from our consultants. Three‑point internal micrometer MS908.655 — self‑centring, carbide measuring faces (20–25 mm) by Metav IndustryLine The Three‑point internal micrometer MS908.655 is a self‑centring internal measuring instrument designed for accurate measurement of blind holes in precision engineering and workshop environments, offering an analogue reading with fine resolution for repeatable results Self‑centring three‑point mechanism Carbide measuring faces for wear resistance Measurement accuracy 0.004 mm Compact range 20–25 mm for fine parts Precise blind‑hole measurement with minimal setup The instrument delivers high repeatability through its self‑centring three‑point mechanism, which ensures concentric contact inside blind bores without complex alignment. With a rated accuracy of 0.004 mm and an analogue reading of 0.005 mm, the device is engineered for tasks where micrometre‑level certainty matters; this combination reduces rework and measurement uncertainty in small components. The compact design is especially suited to micro fabrication and precision inspection of housings and bores. Durable contact faces and dependable mechanical operation Carbide contact faces provide excellent wear resistance, maintaining measurement integrity over extended use in workshop conditions. The analogue nonius construction offers tactile feedback preferred in many inspection routines and requires no batteries or electronic interfaces, supporting uninterrupted operation on the shop floor. The included adjustment ring (25) enables straightforward zeroing and fine setting, while the robust build keeps the mechanical play to a minimum for consistent results. Designed for micro‑range quality control and fine parts Classified in the micro range (suitable for 10–100 mm scales), the 20–25 mm span targets small‑format parts such as precision sleeves, bearing bores and microassemblies. Its compact dimensions and precise geometry make it practical for use in bench inspection and in‑process checks where access is restricted. The measuring faces and frame geometry have been selected to balance stiffness and accessibility, ensuring stable measurements even when handling delicate components. Integration into workshop procedures and traceability The analogue three‑point gauge complements digital and traditional inspection tools as part of a consistent metrology chain; repeatable manual results simplify tolerance checks and go/no‑go decisions. Further technical documentation and measurement data are available from Metav Werkzeuge for integration into QA processes and production control. For operators transitioning from standard calipers or bore gauges, the instrument provides a clear step up in concentricity control without introducing complex electronics. For specification advice or to secure the MS908.655 from Metav IndustryLine, contact Metav Werkzeuge for personalised guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.655 Manufacturer: Metav IndustryLine Product: Three‑point internal micrometer Numbers / Core technical data Measuring range: 20–25 mm Reading / resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features / Materials Self‑centring three‑point mechanism Carbide measuring faces Analogue nonius scale Suitable for blind‑hole measurement FAQ What measuring range does the MS908.655 cover? The MS908.655 covers a measuring range of 20–25 mm, making it suitable for small bores and fine mechanical components. How precise is the instrument for repeatable checks? The three‑point internal micrometer achieves a stated accuracy of 0.004 mm with an analogue reading of 0.005 mm, designed for consistent bench and in‑process inspection. Are the measuring faces wear resistant? Yes, the contact faces are made of carbide, providing enhanced wear resistance and long‑term dimensional stability for routine use. Is the gauge suitable for blind‑hole applications? The instrument is explicitly intended for blind‑hole measurement, featuring a self‑centring mechanism that ensures concentric contact within such bores. Does Metav IndustryLine provide technical support for integration into QA procedures? Metav IndustryLine and Metav Werkzeuge can supply further technical documentation and advice to assist with integration of the MS908.655 into quality control workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20-50mm Three-Point Internal Micrometer Self-Centring Set, 4 Pieces in Case - Metav IndustryLine
Take advantage of a self-centring three‑point system together with wear‑resistant carbide measuring faces and a fine 0.005 mm analogue graduation for repeatable blind‑hole measurements. Order the set directly via Metav Werkzeuge or contact our consultants for advice on matching extensions and gauges to specific bores. Three‑point internal micrometer MS908.673 — self‑centring, 0.005 mm analogue The Three‑point internal micrometer MS908.673 is an analogue, self‑centring inside micrometer designed for precise measurement of blind holes in fine mechanical and workshop applications Self‑centring three‑point measuring system Hardmetal measuring faces (carbide) Analogue resolution 0.005 mm Designed for blind‑hole measurement Repeatable centring for reliable results The micrometer’s defining benefit is its self‑centring three‑point head, which aligns reliably in blind bores and reduces off‑axis error during measurement. This design converts operator input into a consistent contact geometry, lowering variance between individual readings and helping to meet process tolerances with fewer rechecks. The analogue graduation with 0.005 mm division gives a clear, immediate view of dimensional changes; when traceable comparability is required, the instrument’s mechanical simplicity supports straightforward in‑house verification routines. Built for longevity and stable contact Measuring faces made from carbide (hardmetal) ensure high wear resistance where repeated contact with bore edges would otherwise round or score softer contacts. The harder contact points preserve nominal diameter and shape over long production runs, translating into lower replacement frequency and a steadier measuring baseline. Where repeatability over time matters for quality control, the combination of robust contact materials and the three‑point geometry yields consistent seating in the bore and predictable measurement behaviour. Practical set composition and extension options Supplied as a set of four, this analogue internal micrometer covers a practical range for precision blind‑hole work and fast gauge changes between nominal sizes. Extensions are available up to 150 mm, enabling larger or deeper bores to be reached without sacrificing centring performance. The instrument is analogue by construction, making it straightforward to use alongside existing mechanical measuring tools; shops that prefer simple, robust gauges will appreciate the minimal maintenance and easy field adjustments afforded by the setting rings. Clear advantages in process environments In repetitive inspection tasks or small‑batch production, the instrument’s self‑centring function reduces operator training time and speeds routine checks. The carbide faces and solid construction lower total cost of ownership by reducing wear‑related drift; together with the fine analogue graduation, these characteristics deliver a balance of durability and measurement fidelity that supports reliable quality control in component manufacture. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine three‑point internal micrometer MS908.673 and available extensions fit into current inspection routines and to request a tailored quotation Technical data Article number: MS908.673 Manufacturer: Metav IndustryLine Category: Messschrauben Measuring principle: Analogue (mechanical) Facts Measuring range: 20–50 mm Reading / graduation: 0.005 mm Pieces per set: 4 Extension option: 150 mm Special features Self‑centring three‑point design Hardmetal (carbide) measuring faces Suitable for blind‑hole measurements Analogue nonius graduation FAQ What measurement range does the instrument cover? The set covers a 20–50 mm measuring range, supplied as a set of four sizes to allow quick changes between nominal diameters. Is the micrometer suitable for blind‑hole bores? Yes — the instrument is explicitly designed for blind‑hole measurements, its three‑point, self‑centring head ensuring reliable seating where standard internal callipers may not centre. What is the smallest readable increment on the scale? The analogue nonius offers a 0.005 mm graduation for fine visual readings and repeatable comparison checks. Are extension rods available for deeper bores? Extension rods up to 150 mm are available to access deeper or recessed bores while maintaining the self‑centring capability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200-225mm Three-Point Internal Micrometer Self-Centring, Interchangeable Anvils, Delivered in Case - Metav IndustryLine
Take advantage of the self-centring three-point system and interchangeable measuring insert for reliable blind-hole measurements; combined with carbide measuring faces and an accuracy of ±0.007 mm, this instrument supports consistent quality control. Order the (three-point internal micrometer MS908.667) directly via (Metav Werkzeuge) or ask our consultants if needed. Three-point internal micrometer MS908.667 — self-centring, interchangeable insert The three-point internal micrometer for precise measurement of blind bores in workshop and inspection environments, designed as a mechanical instrument for repeatable internal diameter checks. Self-centring three-point system Interchangeable measuring insert Carbide measuring faces for wear resistance High precision ±0.007 mm Reliable blind-bore measurement with minimal operator influence The three-point system centres automatically within blind bores, reducing alignment errors and giving a reproducible contact geometry; this produces consistent results when inspecting bores. With a reading resolution of 0.005 mm (vernier) and a stated accuracy of ±0.007 mm, the instrument narrows measurement uncertainty to a level suitable for many workshop and production control tasks. The effect is a measurable reduction in rework and faster go/no-go decisions on turning and drilling operations. Durable contact surfaces and easy servicing save time Hard-wearing carbide measuring faces extend service intervals and maintain measurement integrity under repeated use. The measuring insert is exchangeable, which simplifies maintenance and allows quick replacement of worn contacts without discarding the whole instrument. The mechanical construction is straightforward and low-maintenance compared with electronic systems, making it suitable for environments where robustness and simple servicing are priorities. Size and handling tuned to everyday workshop needs Classified in the standard measuring range (measuring range 200–225 mm), this device offers a practical balance of reach and stiffness for typical machine‑shop components such as housings, sleeves and medium-sized bores. The instrument’s overall length of 145 mm supports good accessibility in confined bores while remaining easy to handle during repeated checks. As an analogue instrument with a vernier readout, it performs reliably where electronic readouts are unnecessary or undesired. Confidence for quality control and process stability Intended for routine inspection and in-process checks, the micrometer’s self-centring action and robust contact faces reduce operator-dependent variation and increase throughput in batch inspection. The interchangeable insert concept supports lifecycle planning: wear parts can be stocked and replaced quickly to maintain traceable measurement performance. The device is suitable for blind-hole measurement tasks and integrates well into manual quality-control workflows where mechanical verifiability is required. Contact Metav Werkzeuge today for ordering details and specification advice on the Metav IndustryLine three-point internal micrometer MS908.667 and its spare measuring inserts Technical Data Article number: MS908.667 Manufacturer: Metav IndustryLine Category: Micrometers (internal micrometer) Facts Measuring range: 200–225 mm Reading / Resolution: 0.005 mm Accuracy: ±0.007 mm Overall length: 145 mm Display: analogue (vernier) Features & Delivery Self-centring three-point system Carbide measuring faces Interchangeable measuring insert Designed for blind bores (blind-hole measurement) Mechanical, analogue instrument FAQ How does the three-point centring reduce measurement error? The self-centring three-point mechanism distributes contact forces evenly; the three-point internal micrometer MS908.667 centres itself in the bore to reduce eccentricity and improve repeatability. Can the measuring faces be replaced when worn? Yes — the instrument is fitted with an exchangeable measuring insert, so worn carbide faces can be renewed without replacing the entire micrometer. Is the reading digital or mechanical? The device uses a mechanical vernier readout with a reading resolution of 0.005 mm, offering a robust, electronics-free solution for workshop environments. For which bore types is this instrument intended? It is designed specifically for blind bores; the three-point configuration ensures reliable contact geometry in such applications. What is the measuring range and typical accuracy? The measuring range is 200–225 mm and the stated accuracy is ±0.007 mm, suitable for standard workshop inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
225-240mm Three-Point Internal Micrometer Self-Centering Exchangeable Anvils, Supplied in Case - Metav IndustryLine
Take advantage of self‑centring three‑point measurement and carbide measuring faces for consistent, reproducible results in blind‑hole bores; the interchangeable measuring inserts allow flexible adaptation across the nominal range. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.668 — self‑centring, carbide faces (Metav IndustryLine) The MS908.668 is a three‑point internal micrometer for accurate measurement of blind‑hole bores in workshop and inspection environments. Self‑centring three‑point measuring head Carbide measuring faces for wear resistance Interchangeable measuring inserts Delivered in protective case Faster, repeatable centring in blind‑hole measurement The self‑centring three‑point measuring head significantly reduces setup time when inspecting blind‑hole bores. By contacting the bore with three equidistant measuring points the instrument centres itself automatically, which improves repeatability compared with two‑point probes and speeds up routine checks. The analogue mechanism keeps the operation straightforward for technicians and maintenance staff who require reliable results without complex electronics. Metrology performance you can rely on Designed for industrial use, the instrument offers a stated accuracy 0.007 mm and a resolution 0.005 mm, values that make it well suited for quality control in machining and assembly. These specifications mean the device detects small deviations while providing a clear mechanical indication of the measurement. The combination of robust mechanical gearing and a clear, fine graduation supports precise readings under standard workshop conditions, helping to maintain product tolerances and reduce the risk of costly rework. Durable contact surfaces and flexible inserts The measuring faces are carbide tipped to resist wear during frequent use, preserving the nominal geometry and ensuring long‑term stability. Interchangeable measuring inserts permit adaptation across the stated measuring span so one instrument can cover a range of bore diameters without compromising accuracy. Supplied in a protective case, the tool is ready for transport to the machine or for storage in an inspection cabinet, keeping the measuring faces protected between uses. Trusted partner for precision tasks As part of the Metav IndustryLine range, this three‑point internal micrometer benefits from the supplier’s focus on accessibility and reliability. Metav’s approach to precision brings workshop‑grade metrology within reach, backed by a broad product portfolio and proven logistical support from Emmerich. The instrument suits metrology labs, maintenance teams and production lines that prioritise consistent centring, wear resistance and straightforward operation. For expert advice or to purchase the Metav IndustryLine three‑point internal micrometer MS908.668 with interchangeable inserts and carbide faces, please contact Metav Werkzeuge for tailored assistance and fast supply Technical data Article number: MS908.668 Brand: Metav IndustryLine Category: Messschrauben Numbers / Facts Measuring range: 225–240 mm Resolution (reading): 0.005 mm Accuracy: 0.007 mm Length: 145 mm Analogue instrument Special features / Versions Self‑centring three‑point measuring head Carbide measuring faces Interchangeable measuring inserts Suitable for blind‑hole bores Supplied in protective case FAQ What measuring range does the instrument cover? The MS908.668 three‑point internal micrometer covers a measuring span from 225 mm to 240 mm as delivered. Is this tool suitable for blind‑hole measurements? Yes; the three‑point, self‑centring design is specifically intended for reliable measurement of blind‑hole bores. Can the measuring inserts be replaced to adjust for different bore sizes? Interchangeable measuring inserts are provided, allowing the instrument to be adapted across its nominal measuring span. How precise are the readings from this analogue instrument? The instrument provides a resolution of 0.005 mm with a stated accuracy of 0.007 mm, suitable for workshop and production quality checks. Are the measuring faces durable under regular workshop use? The contact points are carbide tipped to increase wear resistance and maintain geometric integrity over extended use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25-30mm Three-Point Internal Micrometer Self-Centering, 0.004mm Accuracy, Supplied in Case - Metav IndustryLine
Take advantage of the combination of precise 0.004 mm accuracy, a self‑centring three‑point measuring head and carbide measuring faces for consistent blind‑hole measurement; order directly via Metav Werkzeuge or contact the consultancy team for tailored advice. MS908.656 Three‑Point Internal Micrometer — Self‑centring, 25–30 mm range (Metav IndustryLine) A three‑point internal micrometer designed for accurate measurement of blind holes and restricted bores in the 25–30 mm range, combining a compact form with stable contact geometry. Three‑point self‑centring measuring head Measuring range 25–30 mm Carbide measuring faces for wear resistance Analogue drive with 0.005 mm resolution Consistent results for blind‑hole inspection The instrument's self‑centring three‑point system guarantees repeatable contact with bore surfaces, reducing setup variance and rework in production inspection. The compact contact geometry suits restricted bores where standard callipers cannot reach, while the analogue drive and fine spindle allow controlled approach to the measuring surfaces. This configuration translates directly into fewer rejected parts and more reliable pass/fail decisions on the shop floor. Precision that meets workshop demands With a documented accuracy of 0.004 mm and a readable resolution of 0.005 mm, the device sits between general workshop tools and high‑precision instruments. The mechanical design and robust spindle ensure stable readings even in routine quality control. For applications that require exact internal diameters in small assemblies, this micrometer provides a balance of sensitivity and practical handling without invoking complex electronic systems. Durable contact surfaces for long service life The measuring faces are made from carbide, offering superior wear resistance under frequent use and abrasive conditions. That hard contact material preserves the reference geometry over many cycles and keeps measurement uncertainty low. An adjustment ring marked 25 assists with quick reference when setting or checking the nominal diameter, making repetitive tasks more efficient and less error‑prone. Compact format for fine mechanical work Classified in the micro range by its 25–30 mm span, the tool is ideal where small, precise components are involved. The short overall length supports handling in confined environments and maintains torsional stiffness for reliable contact pressure. As an analogue internal measuring instrument, it offers familiar operation for technicians while delivering the benefits of a three‑point system designed specifically for blind‑hole measurement. For precise and repeatable blind‑hole measurement, contact Metav Werkzeuge to request the Metav IndustryLine three‑point internal micrometer MS908.656 or to speak with a specialist at info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: MS908.656 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Facts Measuring range: 25–30 mm Resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features Self‑centring three‑point measuring head Carbide measuring faces Analogue micrometer design Adjustment ring marked 25 Suitable for blind‑hole measurement FAQ What measuring range does this instrument cover? The three‑point internal micrometer MS908.656 covers a measuring range of 25–30 mm, suited to small‑bore and blind‑hole applications. Is this micrometer suitable for blind‑hole measurement? Yes, the self‑centring three‑point system of the Metav IndustryLine three‑point internal micrometer is specifically designed to measure blind holes and restricted bores reliably. What accuracy and resolution can be expected? The instrument provides an accuracy of 0.004 mm with an analogue readable resolution of 0.005 mm, offering precise control for workshop inspections. Are the measuring faces durable for repeated use? The measuring faces are made of carbide, ensuring wear resistance and long‑term stability of the contact geometry under frequent measurement cycles. How is the instrument adjusted for repetitive tasks? An adjustment ring marked 25 is provided for quick reference and repeatable setting when working with the same nominal diameters. Is this a digital instrument? No, the MS908.656 is an analogue internal micrometer, combining mechanical reliability with a fine spindle for controlled readings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250-275mm Three-Point Internal Micrometer Self-Centring Interchangeable Spindle, 0.007mm Accuracy, Supplied in Case - Metav IndustryLine
Combine reliable self‑centring measurement with a 250–275 mm measuring range and interchangeable measuring inserts for consistent, repeatable bore checks; order the instrument directly via Metav Werkzeuge or consult their specialists for application advice. Three‑point internal micrometer MS908.669 — self‑centring bore micrometer, 250–275 mm (Metav IndustryLine) The Three‑point internal micrometer MS908.669 is a self‑centring bore micrometer designed for precision measurement of blind holes in machining and workshop quality control. Self‑centring three‑point measurement Measuring range 250–275 mm Accuracy ±0.007 mm Interchangeable measuring insert Accurate bore measurement where alignment matters The three‑point design provides a self‑centring contact with the bore, which reduces alignment error and speeds up set‑up when checking blind holes. With a stated accuracy of ±0.007 mm and an analogue reading step of 0.005 mm, the instrument delivers reproducible results for routine quality checks. The mechanical nonius format keeps the workflow straightforward and avoids dependencies on batteries or electronics, supporting continuous shop‑floor operation. Robust construction for workshop use Classified within the standard range for workshop micrometres, the device covers 250–275 mm, a span that balances reach and stiffness for typical machine‑shop components. The measuring faces are made of carbide, improving wear resistance when probing machined bores. The interchangeable measuring insert system allows quick replacement of worn or specialised tips, extending the instrument’s service life and adapting it to specific bore geometries. Practical handling to reduce cycle time Designed for efficient operation, the instrument’s three‑point geometry centres itself in the bore and thus shortens measurement cycles compared with multi‑step setups. The analogue format is tactile and direct, providing immediate feedback during measurement. Supplied in a protective case for secure transport, the tool is ready for use at different workstations and is dimensioned to be handled easily by one operator for most inspection tasks. Reliable data for consistent quality control Used within a production or inspection routine, the micrometer supports fast go/no‑go decisions and reduces rework by providing consistent internal diameter readings. The combination of a defined measuring range, carbide contact faces and an exchangeable insert system means fewer interruptions for maintenance and predictable measurement behaviour over time. The instrument is especially well suited to blind‑hole verification in component production, jig making and fitting operations. Contact Metav Werkzeuge today to discuss how the MS908.669 can be integrated into existing inspection routines or to arrange a tailored measurement solution from their Emmerich facility Technical data Article number: MS908.669 Product type: Three‑point internal micrometer Brand: Metav IndustryLine Facts Measuring range: 250–275 mm Measuring range (min): 250 mm Measuring range (max): 275 mm Accuracy: ±0.007 mm Reading increment: 0.005 mm Length: 145 mm Special features Self‑centring three‑point measurement Carbide measuring faces Interchangeable measuring insert Suitable for blind‑hole bores Supplied in protective case Analogue mechanical instrument FAQ What measuring range does the instrument cover? The instrument covers a measuring range of 250–275 mm, intended for medium‑sized bores in workshop use. Is the device suitable for blind‑hole measurements? Yes, the three‑point, self‑centring geometry is specifically designed for reliable measurement of blind holes. What accuracy and resolution can be expected? The micrometer offers an accuracy of ±0.007 mm with an analogue reading increment of 0.005 mm. Can the measuring faces be replaced or adapted? The instrument features an interchangeable measuring insert, and the measuring faces are carbide for long service life. How is the product delivered and how is it identified? The tool is supplied in a protective case and is listed as MS908.669 from Metav IndustryLine Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
30-40mm Three-Point Internal Micrometer Self-Centering, Supplied in Case - Metav IndustryLine
Take advantage of the combination of compact, workshop‑grade precision and robust design for repeatable blind‑hole measurement; the self‑centring three‑point contact and hardened measuring faces deliver reliable results across production and maintenance tasks. Order the instrument directly via Metav Werkzeuge or consult our advisors for application guidance. Three‑point internal micrometer MS908.657 (Metav IndustryLine) — Self‑centring, 30–40 mm The Three‑point internal micrometer MS908.657 is a mechanically driven measuring instrument intended for precise internal diameter checks, especially blind‑hole applications in fine mechanical and light industrial environments. Self‑centring three‑point contact system Measurement range 30–40 mm Hardened measuring faces for durability Precision designed for blind‑hole measurement The three‑point geometry provides self‑centring contact inside blind holes, ensuring that the contact points align automatically with the bore axis and thereby reduce eccentricity errors. With an accuracy of ±0.004 mm and a mechanical reading of 0.005 mm, this analogue measuring instrument translates fine thread motion into dependable metrology results without electronic dependence. The three‑point contact method also helps to average minor surface irregularities, which can reduce rework and speed up routine inspection tasks, making it suitable for both small series production and maintenance checks. Compact format for fine mechanical work Classified in the Mikro range (measurement span up to 100 mm), the instrument’s 30–40 mm span and overall length of 97 mm offer a favourable balance between reach and stiffness. This makes the device well suited to precision tasks where space is limited, such as watch and instrument repair, small housings and insert fittings. The hardened measuring faces increase wear resistance and preserve measurement consistency over long service intervals, so that calibration intervals remain predictable and downtime is minimised. Workshop‑ready robustness and simple handling The analogue design emphasises mechanical reliability: a clear adjustment ring (setting ring 40) allows quick pre‑setting and repeatable contact positioning, while the compact construction withstands everyday workshop handling. Delivered in a protective case for transport, the micrometer is prepared for secure storage and movement between benches or sites. The instrument’s straightforward operation and sturdy build lower the barrier to consistent metrology in production, inspection and maintenance workflows while keeping measurement practice transparent and traceable. Contact Metav Werkzeuge today for tailored application advice on the Metav IndustryLine Three‑point internal micrometer MS908.657 and ensure the right fit for blind‑hole inspection in your workshop Technical data Article number: MS908.657 Manufacturer: Metav IndustryLine Product type: Three‑point internal micrometer Suitable for: Blind‑hole measurement Core data Measurement range: 30–40 mm Length: 97 mm Accuracy: ±0.004 mm Reading (resolution): 0.005 mm Adjustment ring: 40 Mechanical type: Analogue Special features Self‑centring three‑point contact Hardened measuring faces Delivered in protective case for transport Suited to fine mechanical and light industrial use FAQ What makes the three‑point contact better for blind holes? The three‑point geometry centres itself in the bore and averages contact positions; the MS908.657 uses this principle to reduce eccentricity and provide stable internal diameter readings for blind‑hole applications. What accuracy and resolution can be expected from this instrument? The instrument offers an accuracy of ±0.004 mm with a mechanical reading of 0.005 mm, giving precise analogue measurement suitable for production checks and workshop inspection. Is the device suitable for watchmaking and small parts? Yes. With its compact dimensions and classification in the Mikro range, the micrometer is well adapted to fine mechanical work, small housings and components where a short, stiff measuring span is required. Are the measuring faces wear‑resistant? The micrometer is supplied with hardened measuring faces, which increases durability and helps maintain measurement consistency over extended use. Does the delivery include a protective case? The instrument is supplied in a protective case for transport and secure storage, making it straightforward to move between benches or sites. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40-50mm Three-Point Internal Micrometer Self-Centring, Precision 0.005mm, Supplied in Case - Metav IndustryLine
Benefit from the combination of self‑centring three‑point contact, 0.005 mm accuracy and carbide measuring faces to secure reproducible blind‑hole measurements; order the MS908.658 directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.658 — self‑centring, 40–50 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.658 is a self‑centring, analogue instrument intended for precision measurement of blind holes and internal bores in small to medium components, offering a compact solution for fine mechanical and toolmaking tasks. Self‑centring three‑point measurement High precision: 0.005 mm accuracy Carbide measuring faces for durability Measuring range 40–50 mm for blind holes Reliable accuracy for critical fits and assemblies The MS908.658 delivers a resolution of 0.005 mm with a matching accuracy of 0.005 mm, providing measurable repeatability for tolerance‑sensitive internal features. The finely graduated analogue scale suits production and workshop environments where a tactile, immediate reading is preferred over electronic systems. This level of precision reduces rework and inspection time by supplying a clear, verifiable measurement result that supports quality control routines and efficient process decisions. Compact, micro‑range design that reduces handling error Classified in the micro range (max. 10–100 mm), the instrument’s 40–50 mm span targets finely detailed components such as small housings, inserts and precision sleeves. The self‑centring mechanism with three‑point contact automatically aligns the measuring faces within a bore, lowering sensitivity to off‑axis entry and operator variance. The compact form factor and balanced length make single‑handed operation straightforward, improving throughput where frequent in‑process checks are required. Durable measuring faces for long‑term repeatability Equipped with carbide (hardmetal) measuring faces, the micrometer resists wear and maintains measurement integrity across extended use. Carbide tips provide a hard, stable contact surface that minimises surface damage to workpieces while preserving repeatable reference points. For workshops seeking a robust, low‑maintenance gauge, this construction ensures a consistent lifecycle performance and contributes to lower total cost of ownership over time. Practical handling, calibration and typical applications The instrument is analogue and supplied with a setting ring at 40 mm to simplify zeroing and quick verification before series checks. Its total length of 97 mm facilitates access to compact bores while keeping the device rigid during measurement. Typical applications include blind‑hole inspection in toolmaking, component verification in precision engineering and quick fit checks in assembly processes. For specification matching and integration into inspection routines, Metav’s product consultants can assist with selection and measuring technique recommendations. Choose the Metav IndustryLine MS908.658 for reproducible blind‑hole measurement and contact Metav Werkzeuge in Emmerich for tailored technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: MS908.658 Type: Three‑point internal micrometer Brand: Metav IndustryLine Measuring range: 40–50 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm Operation: Analogue Setting ring: 40 Length: 97 mm Facts Measuring range: 40–50 mm Resolution: 0.005 mm Accuracy: ±0.005 mm Length: 97 mm Special features Self‑centring mechanism Three‑point contact for blind‑hole measurement Carbide (hardmetal) measuring faces Suited for fine mechanical and toolmaking applications Analogue scale for immediate readings FAQ What bore sizes can be measured with this instrument? The MS908.658 covers internal dimensions in the 40–50 mm range and is optimised for blind‑hole measurement within that span. How precise is the measurement capability? The instrument offers a resolution of 0.005 mm with an accuracy rated at 0.005 mm, suitable for many tolerance‑sensitive internal checks. Are the measuring faces wear‑resistant? Yes, the MS908.658 is fitted with carbide (hardmetal) measuring faces, which provide superior wear resistance and long‑term repeatability. Is this gauge suitable for production‑line checks? Its compact, analogue design and self‑centring three‑point system make the micrometer well suited to repetitive in‑process inspections and quick verification tasks. Does the micrometer require electronic data output? This model is analogue and does not include electronic data output; it is designed for direct, fast readings on the shop floor. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50-63mm Three-Point Internal Micrometer Self-Centring, Supplied in Case - Metav IndustryLine
Take advantage of a self‑centring three‑point measuring head and a 0.005 mm accuracy across a compact 50–63 mm range for reproducible blind‑bore inspections; order the instrument directly via Metav Werkzeuge or consult the specialists for application advice. Three‑point internal micrometer MS908.659 — Metav IndustryLine, self‑centring, 50–63 mm The Three‑point internal micrometer is a precision instrument designed for accurate measurement of blind bores and other internal diameters within the 50–63 mm range, combining a self‑centring three‑point head with robust analogue mechanics for repeatable results. Self‑centring three‑point measuring head Range 50–63 mm Accuracy 0.005 mm Carbide measuring faces Reproducible internal measurements through self‑centring design The instrument’s self‑centring three‑point measuring head converts small operator variations into consistent contact across the bore, which reduces eccentricity and minimises measurement scatter. With a declared accuracy of 0.005 mm and an analogue readout, this tool offers a clear, verifiable performance baseline that supports process control and reduces rework in production environments. The three‑point geometry is particularly effective on short to medium blind bores, where central alignment is critical to obtain reliable diameter values. Built for workshop use: durable faces and compact handling Equipped with carbide measuring faces, the device resists wear from regular contact with machined surfaces and maintains form integrity during frequent use. The compact overall length of 114 mm and a setting ring of 62 support comfortable handling in workshop and inspection‑bench situations, enabling efficient measurement cycles without sacrificing stiffness. As an analogue instrument, it delivers straightforward operation and low maintenance while providing the tactile feedback many technicians prefer for repeat measurements. Practical benefits for quality assurance and inspection routines Integrating this internal micrometer into quality checks provides a direct improvement to inspection throughput and measurement consistency. The tool is explicitly suitable for blind‑bore applications and mechanical assembly checks, offering a reliable technical solution where calipers or telescoping gauges may be less repeatable. The combination of a robust three‑point head and carbide contact faces translates into fewer measurement-related interruptions and a steadier conformity assessment across batches. Contact Metav Werkzeuge in Emmerich for tailored advice on application and availability of the MS908.659 three‑point internal micrometer Technical data Article number: MS908.659 Product: Three‑point internal micrometer Manufacturer: Metav IndustryLine Numbers / Core technical data Measuring range: 50–63 mm Minimum range: 50 mm Maximum range: 63 mm Reading / resolution: 0.005 mm Accuracy: 0.005 mm Length: 114 mm Setting ring: 62 Special features / Designs Self‑centring three‑point head Carbide (hard‑metal) measuring faces Analogue mechanical operation Suitable for blind bores FAQ What degree of accuracy can be expected from this three‑point internal micrometer? The MS908.659 from Metav IndustryLine delivers an accuracy of 0.005 mm with a 0.005 mm reading increment, suitable for precise workshop inspection tasks. Is this instrument suitable for blind‑bore measurement only? While optimised for blind bores, the three‑point internal micrometer is also applicable to other internal diameter checks where central alignment and repeatability are required. How does the self‑centring feature improve measurement results? The self‑centring three‑point head ensures even contact around the circumference, reducing eccentricity and enabling more reproducible diameter readings during routine inspections. What maintenance is recommended to retain measurement reliability? Regular cleaning of the carbide faces and periodic verification against a calibrated ring gauge will preserve the instrument’s performance; the analogue mechanics favour simple, on‑site care. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6-12mm Three-Point Internal Micrometer Self-Centering Set, Supplied in Case - Metav IndustryLine
Take advantage of self‑centring three‑point measurement, hardened measuring faces and a compact 6–12 mm range to inspect blind bores with repeatable accuracy; the set format provides practical coverage across small diameters. Order the Three‑point internal micrometer set MS908.671 directly via Metav Werkzeuge or ask our consultants if needed. Three‑point internal micrometer MS908.671 — self‑centring, hardened faces by Metav IndustryLine The Three‑point internal micrometer MS908.671 is an analogue, precision measuring set for blind‑hole inspection in the micro class, designed to deliver stable readings in confined diameters. Self‑centring three‑point measuring system Measuring range 6–12 mm in micro class Hardened measuring faces for durability Includes adjustment rings 6, 8, 10 mm Precision for small bores and repeatable inspection results This set is classified in the micro class with a 6–12 mm measuring span, making it suitable where short measuring jaws and torsion‑resistant geometry matter. The compact dimensions reduce lever effect and deformation during measurement, which benefits quality control in precision engineering and small‑parts production. As an analogue instrument, it provides a tactile feel during adjustment and a reliable mechanical reference that is simple to verify against calibration standards. Stable centring and wear‑resistant contact surfaces The self‑centring three‑point system ensures the contact points centre automatically in blind bores, reducing centring errors and shortening setup time. Combined with hardened measuring faces, this mechanism keeps contact geometry consistent over many cycles and supports repeatable results when inspecting internal diameters. Included adjustment rings (6, 8, 10 mm) and a 100 mm extension option expand the practical use for varying bore depths and minor diameter steps without compromising alignment. Practical workshop benefits and typical applications Offered as a set of three, the instrument collection covers successive diameter bands within the stated range, which streamlines inspection in toolrooms, fixture production and component assembly lines. The analogue micrometer screw provides fine mechanical control for small adjustments, while the robust design minimises maintenance needs. This combination of features helps to reduce rework, improve first‑pass yield and integrate smoothly into established inspection routines in small‑part manufacture. Contact Metav Werkzeuge to discuss the Metav IndustryLine three‑point internal micrometer set MS908.671 for blind bores and arrange supply or technical advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.671 Manufacturer: Metav IndustryLine Product type: Three‑point internal micrometer set Reading type: Analog Measuring range: 6.0–12.0 mm Pieces per set: 3 Extensions: 100 mm Adjustment rings: 6 mm, 8 mm, 10 mm Hardened measuring faces: yes Self‑centring: yes Facts Measuring range min: 6 mm Measuring range max: 12 mm Reading increment: 0.005 mm Set quantity: 3 pieces Extension length: 100 mm Special features Self‑centring three‑point system Hardened contact faces for long life Analogue micrometer screw drive Suited for blind‑hole/internal bore measurement Compact micro‑class design for small diameters FAQ What measuring range is covered by the set? The set covers a 6–12 mm measuring span suited to micro‑class internal measurements. Is the instrument suitable for blind‑hole inspection? Yes, the Three‑point internal micrometer MS908.671 is specifically designed for blind‑hole (sack‑hole) measurements using a self‑centring three‑point contact system. Are extensions and adjustment rings included? Adjustment rings of 6, 8 and 10 mm are included and a 100 mm extension option is listed for deeper bore measurements. Are the measuring faces hardened? The measuring faces are hardened to resist wear and preserve contact geometry during repeated use. How many instruments are supplied in the set? The delivery comprises a set of three instruments to cover the stated diameter range efficiently. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
62-75mm Three-Point Internal Micrometer Self-Centring, 0.005mm Graduation, Supplied in Case - Metav IndustryLine
Benefit from the self-centring design, carbide measuring faces and ±0.005 mm accuracy to secure reproducible internal measurements in compact assemblies; order the three-point internal micrometer directly via Metav Werkzeuge or consult our specialists for technical guidance. Three-point internal micrometer MS908.660 — self-centring, 62–75 mm range A compact, analogue three-point internal micrometer designed for precise internal diameter checks in confined bores and fine-mechanical work. Self-centring three-point mechanism Measuring range 62–75 mm High accuracy ±0.005 mm Carbide measuring faces, analogue Precision where access is restricted The three-point internal micrometer is engineered for accurate measurements in confined spaces. Its self-centring mechanism ensures the measuring anvils align centrally within a bore, reducing operator-induced eccentricity and improving repeatability. With a readout resolution of 0.005 mm and a verified accuracy of ±0.005 mm, the instrument provides a reliable basis for quality control tasks where small deviations matter. The compact profile and 114 mm body length make this instrument particularly suitable for short, deep bores and components that cannot be accessed with larger gauges, offering precision without the need for complex fixturing. Durable construction for consistent results Built with carbide measuring faces, the instrument resists wear and maintains a stable contact geometry over extended use, which preserves measurement integrity in production environments. The analogue mechanism is robust and free of electronics, making it uncomplicated to operate in workshop conditions where durability is paramount. The combination of hardened contact surfaces and mechanical simplicity translates into low maintenance and consistent performance during repetitive checking routines, supporting efficient inspection workflows on the shop floor. Practical handling and typical applications Designed for ease of use in inspection and assembly, the instrument delivers fast, reliable readings for internal diameters between 62 and 75 mm. Its three-point contact is particularly effective for detecting form deviations and average bore sizes without additional adapters. Typical applications include component verification in machining, maintenance checks on housings and bearings, and quality assurance in small-batch production. The analogue format permits immediate interpretation of results, while the instrument’s geometry supports measurements that would be difficult with external gauges or callipers. Contact Metav Werkzeuge today for tailored advice and to arrange supply of the Metav IndustryLine three-point internal micrometer MS908.660 via Metav Werkzeuge GmbH; technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.660 Brand: Metav IndustryLine Type: Analogue three-point internal micrometer Measuring range: 62–75 mm Readout: 0.005 mm Accuracy: ±0.005 mm Body length: 114 mm Self-centring mechanism Carbide measuring faces Suitable for blind-hole measurement Analogue (mechanical) operation FAQ How accurate is the three-point internal micrometer for routine inspection? The MS908.660 delivers an accuracy of ±0.005 mm, making it suitable for routine precision checks and quality control where sub-hundredth-millimetre repeatability is required. Can the instrument be used in blind or recess bores? Yes, the design is intended for confined and blind-hole measurements; the three-point contact provides reliable central alignment inside such bores. What maintenance is required to preserve measurement accuracy? Regular cleaning of contact surfaces and occasional verification on a calibrated reference ring are recommended to maintain the micrometer’s performance; the carbide measuring faces reduce wear and extend intervals between checks. Is the readout mechanical or electronic? This is an analogue instrument with a mechanical readout at 0.005 mm resolution, favouring robustness in workshop settings without relying on electronics. Which environments and applications suit this instrument best? The three-point internal micrometer is ideal for machine shops, maintenance workshops and inspection benches where compact, repeatable internal measurements are needed across small to medium-sized components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6–8mm Three-Point Internal Micrometer Self-Centring For Blind Holes In Plastic Case - Metav IndustryLine
Compact, self‑centring three‑point internal micrometre with a 6.0–8.0 mm measuring range and high mechanical resolution; the MS908.650 combines precise blind‑hole measurement with hardened measuring faces and a fine 0.001 mm reading—Order the three‑point internal micrometre directly via Metav Werkzeuge or ask our consultants if needed Three‑point internal micrometre MS908.650 — self‑centring, 6.0–8.0 mm range Three‑point internal micrometre MS908.650 delivers reliable blind‑hole measurement for precision workshops and production lines Self‑centring three‑point contact Measuring range 6.0–8.0 mm Resolution 0.001 mm reading Hardened measuring faces (HM) Precision where blind‑hole bores matter The self‑centring three‑point contact mechanism ensures coaxial alignment inside blind holes, reducing measurement variability compared with two‑point probes. With a measuring range of 6.0–8.0 mm and an analogue vernier controlled fine adjustment, this instrument is optimised for small‑diameter bores where repeatability is critical. The device’s geometry minimises radial play so that each measurement reflects the actual bore diameter rather than positioning error, which is particularly valuable in small‑component assembly and quality control workflows. Exceptional reading and repeatability for workshop standards Equipped with a mechanical reading division of 0.001 mm, the instrument offers a fine visual resolution while the stated accuracy of ±0.004 mm provides a clear performance expectation for routine inspections. The analogue vernier design gives tactile feedback during measurement, enabling experienced operators to control contact force intuitively. This combination of high resolution and guaranteed accuracy supports process control in machining and metrology tasks where small deviations can affect assembly fit or functional tolerances. Durable contact faces for industrial use The micrometre is fitted with hardened measuring faces (HM) to withstand repeated contact with workpiece surfaces and abrasive contaminants found in production environments. These robust faces preserve the geometry of the contact points over long service intervals, which reduces drift and the need for frequent re‑profiling. In practice, hardened faces extend usable life and maintain measurement integrity when inspecting ferrous and non‑ferrous components during serial production. Designed for blind‑hole measurement and simple handling Specifically configured for blind‑hole bores, the three‑point contact and compact body (length 54.5 mm) permit access to confined features that larger gauges cannot reach. The instrument includes an adjustment ring (setting ring 6) that allows controlled extension of the contact arms, making it suitable for varied hole depths within the stated range. Its compact, mechanically driven construction requires no batteries and integrates easily into inspection benches, making it a practical choice for laboratories and on‑shop measuring stations where robustness and low maintenance are priorities. Contact Metav Werkzeuge today to discuss how the MS908.650 can be integrated into existing inspection routines or to request tailored advice from our technical consultants Technical data Article number: MS908.650 Manufacturer: Metav IndustryLine Type: Three‑point internal micrometre Facts Measuring range: 6.0–8.0 mm Length: 54.5 mm Reading increment: 0.001 mm Accuracy: ±0.004 mm Adjustment ring: 6 Special features Self‑centring three‑point contact Hardened measuring faces (HM) Analogue vernier reading Suitable for blind‑hole bores Category: Messschrauben FAQ What measurement range does this instrument cover? The MS908.650 covers a measuring range of 6.0–8.0 mm, optimised for small blind‑hole bores. Is the device suitable for repetitive production checks? Yes, the MS908.650 is designed for workshop and production use with hardened measuring faces and a robust three‑point contact that supports repeatable inspections. What level of accuracy and resolution can be expected? The instrument provides a reading increment of 0.001 mm and a stated accuracy of ±0.004 mm, suitable for demanding quality control tasks. Can the micrometre measure deep blind holes? The compact length (54.5 mm) and the adjustment ring (6) make the MS908.650 appropriate for many blind‑hole depths within its 6.0–8.0 mm range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75-88mm Three-Point Internal Micrometer Self-Centring, Hardened Measuring Faces, Supplied in Case - Metav IndustryLine
Benefit from precise three-point contact, a self-centring mechanism and an accuracy of 0.005 mm for reliable blind‑hole measurement; order the MS908.661 directly via Metav Werkzeuge or ask our consultants for application advice. Three‑point internal micrometer MS908.661 — 75–88 mm range, self‑centring (Metav IndustryLine) The Three‑point internal micrometer MS908.661 offers a compact, mechanically robust solution for accurate measurement of blind bores between 75 and 88 mm, combining repeatable contact geometry with workshop‑grade durability. Self‑centring three‑point contact Measuring range 75–88 mm Accuracy 0.005 mm Precise three‑point geometry for repeatable blind‑hole results The instrument employs a three‑point contact arrangement that engages the bore at equidistant positions, producing consistent centring and minimising eccentricity in blind‑hole measurements. With a specified accuracy of 0.005 mm and a reading increment of 0.005 mm, the mechanical design prioritises repeatability and straightforward interpretation of results. This focus on measurable performance supports quicker decision‑making on the shop floor and reduces the likelihood of rework caused by inconsistent bore centring. Robust construction and easy handling for daily use Built for persistent use in production and inspection areas, the gauge features hardened measuring faces and an analogue measuring mechanism that requires no batteries. The compact body (length 114 mm) and an adjustable setting ring (87) provide tactile control during measurement operations. Hardened contact surfaces extend service life under typical workshop conditions, while the analogue format keeps the instrument immediately usable without electronic maintenance. The combined effect is low‑maintenance operation with dependable mechanical accuracy. Practical suitability and workflow benefits Designed specifically for blind‑hole applications, the tool is suited to toolrooms, maintenance shops and quality control benches where internal diameters must be checked quickly and reliably. The self‑centring action reduces setup time and helps standardise measurement procedures across operators, improving throughput and traceability. As a purely mechanical gauge it integrates easily with established inspection routines and supports rapid pass/fail decisions without additional calibration steps beyond routine verification. Quality assurance and provenance that support procurement Supplied under the Metav IndustryLine umbrella, the instrument represents a balance of functional precision and workshop pragmatism. Choice of a mechanically driven, three‑point internal gauge is a rational investment when repeatability and simple operation are priorities. Metav’s approach to product selection and distribution provides transparency and supply reliability for industrial buyers who prioritise consistent measurement outcomes. For technical availability and procurement of the MS908.661 three‑point internal micrometer, contact Metav Werkzeuge for product guidance and stock information at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: MS908.661 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Core specifications Measuring range: 75–88 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 114 mm Setting ring: 87 Special features Self‑centring three‑point contact Hardened measuring faces Analogue measuring mechanism Suitable for blind‑hole bores Category: Micrometers FAQ What measuring range does this instrument cover? The MS908.661 covers a measuring range of 75–88 mm and is therefore suited to medium‑sized internal diameters such as blind bores in assemblies. How precise is the measurement? Precision is stated as 0.005 mm with a reading increment of 0.005 mm, which ensures repeatable results for standard workshop inspection tasks. Why is three‑point contact advantageous for blind holes? Three‑point contact centres the gauge automatically within the bore, reducing eccentricity and improving repeatability compared with single‑point internal probes. Where is this instrument typically used? This analogue internal micrometer is used in toolrooms, maintenance workshops and quality control where robust, battery‑free measurement of blind bores is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com