High-precision clamping holders with internal coolant for extended tool life
Clamping holders with internal coolant are designed to secure indexable inserts accurately while delivering coolant directly to the cutting edge, reducing thermal load and improving chip evacuation in demanding metalworking operations. Used for turning and internal machining of tough materials, these holders channel the coolant through built-in boreholes to the insert and beneath the chip, which boosts tool life and enhances surface finish. As a reliable system solution, the combination of clamping holder, internal coolant and indexable insert ensures consistent performance at high cutting speeds and under heavy cut conditions.
Klemmhalter 95° DCLNR 2020 K12 for CN-- 1204 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Benefit from a compact turning solution that pairs a 95° clamping angle with compatibility for CN-- 1204 indexable inserts and a right-hand cutting orientation; the combination delivers reliable, repeatable machining in confined turret or toolpost spaces. Order the component through Metav Werkzeuge or consult their advisors for application-specific guidance. Clamping holder DCLN for CN-- 1204 — right-hand, 95° head by Teknik Makina Clamping holder DCLN for CN-- 1204 is a right-hand turning tool holder designed for precision workholding with indexable inserts in industrial and workshop turning applications 95° clamping angle for stable cutting For CN-- 1204 indexable inserts Right-hand turning orientation Compact overall length 125 mm Stable clamping for consistent turning results The combination of a 95° clamping angle and a tailored seat for CN-- 1204 indexable inserts ensures stable clamping and reduced deflection during interrupted or continuous cuts. This geometry translates into more consistent chip formation and improved surface finish on turned parts. The right-hand configuration suits standard lathe setups and enables predictable toolpath planning, which supports higher process repeatability and fewer in-process adjustments. Compact dimensions that suit workshop tooling With an overall length of 125 mm, a head width of 25 mm and a holder height of 20 mm, the design is intentionally space-efficient for multi-tool turrets and small lathes. The cutting height 30 mm aligns the insert tip to standard toolpost centres, simplifying set-up and reducing the need for shim adjustments. The reduced mass (0.441 kg) lowers inertial loading on the turret, aiding quicker accelerations and minimising tool-change impact on cycle time without compromising rigidity. Clear specification for straightforward integration Supplied to ISO DCLNR 2020 profile standards and compatible with a K12 mounting shank, the component is specified for reliable indexing and repeatable seating in common tool holders. The SKU D160TM identifies the exact configuration for procurement and stock control. Technical purchases benefit from the transparency of dimensions and ISO designation, which simplifies NC programming checks and fixture planning while reducing downtime during tool changeovers. Metav Werkzeuge’s inventory approach and product range support consistent replenishment for production and service environments. Contact Metav Werkzeuge to discuss integrating this Teknik Makina turning holder into existing tooling arrays or to request detailed dimensional drawings and delivery options via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: D160TM Brand: Teknik Makina eClass: 21181004 Facts Overall length: 125 mm Cutting angle: 95° Head width: 25 mm Holder width: 20 mm Holder height: 20 mm Cutting height: 30 mm Weight: 0.441 kg Special features For CN-- 1204 indexable inserts ISO designation: DCLNR 2020 Right-hand turning orientation Mounting shank: K12 SKU: D160TM FAQ Which insert type fits this holder? The holder is designed for CN-- 1204 indexable inserts and seats them in the standard pocket geometry for secure clamping. Is this a right- or left-hand holder? This is a right-hand turning holder; the cutting orientation is specified as right-hand in the technical data. What are the key dimensions to check for turret compatibility? Check the overall length 125 mm, head width 25 mm and cutting height 30 mm to ensure correct fit and centre height alignment. What ISO designation applies to the tool profile? The tool corresponds to ISO designation DCLNR 2020, which clarifies the holder geometry for specification and replacement. How is the holder identified for ordering and stock? The item is listed under SKU D160TM and the brand Teknik Makina for precise procurement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Klemmhalter 95° DCLNR 2525 M16 for CN-- 1606 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of secure clamping and precise geometry to improve part finish and extend tool life; the holder's 95° cutting angle and compatibility with CN-- 1606 inserts deliver repeatable results for series turning. Order and technical advice are available via Metav Werkzeuge. Clamping holder DCLN for CN-- indexable inserts (DCLNR 2525) by Teknik Makina — M16, right-hand A Clamping holder DCLN for CN-- indexable inserts engineered for right-hand turning operations, providing secure insert retention and consistent tool position for medium-duty lathe work Right-hand clamping holder, 95° cutting angle Compatible with CN-- 1606 indexable inserts DCLNR 2525 form with M16 shank Overall length 150 mm, cutting height 36 mm, 0.432 kg Precision and stability for demanding turning The DCLN-style toolholder delivers secure clamping that reduces micro-movement at the cutting edge, which directly improves the surface finish and helps to extend insert life. The 95° cutting angle is designed to offer a balance between effective cutting geometry and clearance for interrupted cuts; this results in shorter cycle times because fewer passes are needed to achieve the required profile. For workshops that prioritise repeatability, the precise seating and robust mechanics minimise setup variation and reduce scrap rates. Compatibility and fast set-up for production workflows Designed around the familiar DCLNR 2525 form and an M16 shank, this holder accepts CN-- 1606 indexable inserts, enabling quick insert changes without regrinding or complex re-adjustment. The clear interface between holder and insert simplifies tool inventory management and reduces changeover time, which benefits batch production. The standardised connection makes the holder compatible with many common tool posts and boring bar adaptors, providing practical interchangeability across machines. Designed to enhance workshop efficiency and handling With a 150 mm overall length and 36 mm cutting height, the toolholder offers the reach and geometry needed for typical turning tasks while keeping rigidity high. At 0.432 kg, the unit is lightweight enough to handle easily during set-up yet substantial enough to damp vibration in most lathe arrangements. The result is a practical combination of handling convenience and machining stability that supports consistent throughput and predictable maintenance intervals. For secure, high‑repeatability turning choose Teknik Makina's clamping holder and contact Metav Werkzeuge for supply and technical consultation at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: D162-1TM Manufacturer: Teknik Makina Designation: DCLN for CN-- Indexable Inserts (DCLNR 2525) Facts Overall length: 150 mm Cutting height: 36 mm Holder height: 25 mm Cutting head width: 32 mm Holder width: 25 mm Cutting angle: 95° Weight: 0.432 kg Special features Compatible inserts: CN-- 1606 Shank/thread: M16 Cutting direction: Right-hand ISO designation: DCLNR 2525 Form: DCLN for CN-- indexable inserts FAQ Which indexable inserts fit this holder? The clamping holder accepts CN-- 1606 indexable inserts; the DCLN form is matched to that insert geometry for correct seating and clamping. Is the holder suitable for right-hand or left-hand turning? This toolholder is configured for right-hand cutting direction, matching the specified cutting geometry and chip flow. What is the mounting thread or shank type? The holder uses an M16 shank/thread connection in line with the DCLNR 2525 specification for secure attachment. How does the 95° cutting angle influence machining? A 95° cutting angle gives good frontal clearance and versatility for typical facing and finishing cuts, reducing interference and enabling stable contact at the insert nose. What are the critical dimensions for setup checks? Key dimensions to verify during setup are the 150 mm overall length and the 36 mm cutting height to ensure correct tool centre height and clearance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° DCLNR 3232 P12 for CN-- 1204 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Benefit from secure, repeatable clamping and compatibility with standard CN-- 1204 inserts: the right-hand DCLN holder combines a 95° cutting angle with a 170 mm overall length for stable turning operations. Order directly via Metav Werkzeuge or consult the technical team for application guidance. Clamp holder DCLN for CN-- indexable inserts — right-hand, 95° cutting angle (Teknik Makina) A Clamp holder DCLN for CN-- indexable inserts engineered for right-hand turning, offering a compact 170 mm length and robust geometry for industrial turning applications. Right-hand cutting orientation Compatible with CN-- 1204 inserts Robust 40 mm cutting-head width 170 mm total length, 95° angle Reliable clamping for consistent turning results The DCLNR 3232 designation indicates a standardised interface that ensures repeatable seating of CN-- 1204 indexable inserts. With a holder height of 32 mm and a cutting height of 30 mm, the tool provides a stable contact zone that reduces micro‑movement during operation. Reduced vibration leads to a more consistent surface finish and fewer reworks, which is particularly important for batch production and workshops where predictable output is essential. The item is purpose‑built for turning tasks where dimensional stability and a fixed cutting geometry are required. Geometry that improves chip flow and machining accuracy A 95° cutting angle and 40 mm cutting‑head width focus the cutting forces into a well‑defined area, allowing efficient chip formation when used with the appropriate insert grade. The right‑hand orientation and the 170 mm overall length make the holder suitable for both held‑tool setups and modular turret arrangements. The measured weight of 1.379 kg contributes to a low centre of gravity in the cutting zone, which helps maintain positional accuracy. When matched with suitable inserts, the geometry supports steady cutting conditions and predictable tool behaviour across repeated cycles. Integration into production environments with familiar interfaces The holder uses the common shank designation P12, facilitating integration into existing toolposts and fixtures without the need for custom adapters. Identified as a clamp‑style toolholder, it simplifies insert changes thanks to its standard ISO form, while the DCLNR 3232 format supports widely available CN‑type inserts. For operations that require quick tooling swaps and minimal setup time, the toolholder’s standard interfaces allow technicians to service machines faster and keep productivity high. Supplied by an established precision partner, this unit is appropriate for industrial workshops and specialised job shops alike. For secure, production-ready turning with Teknik Makina’s DCLN clamp holder, contact Metav Werkzeuge for application support and reliable supply from our Emmerich facility. Technical data Article number: D164TM Designation: DCLN for CN-- indexable inserts ISO designation: DCLNR 3232 Brand: Teknik Makina Cutting direction: right Core specifications Total length: 170 mm Weight: 1.379 kg Cutting‑head width: 40 mm Holder width: 32 mm Holder height: 32 mm Cutting height: 30 mm Cutting angle: 95° Special features Compatible with CN-- 1204 indexable inserts Shank designation: P12 Right‑hand turning orientation Suitable for standard turret and toolpost interfaces FAQ Which inserts fit this holder? The clamp holder accepts CN-- 1204 indexable inserts; the DCLN interface is designed for that insert geometry and the ISO designation DCLNR 3232 ensures correct seating. Is the holder right‑hand or left‑hand? This model is a right‑hand turning holder, specified for right‑hand cutting direction and corresponding insert orientation. What are the key dimensions to check for machine compatibility? Important dimensions include the 170 mm total length, 32 mm holder height and 40 mm cutting‑head width; these determine clearance and mounting suitability in a given turret or toolpost. What shank type does the holder use? The holder uses the P12 shank designation, which is compatible with common mounting systems and simplifies integration into existing setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° DWLNL 2020 K06 For WN-- 0604 Innenkühlung Linksschneidend - Teknik Makina
Take advantage of the secure clamping for WN-- 0604 inserts and the defined 95° cutting angle to increase process stability and surface quality; specified dimensions and the left-hand orientation make this holder a practical choice for mirror-image turning operations—order via Metav Werkzeuge or consult their specialists for fitment advice. Klemmhalter DWLNL 2020 — Left-hand turning holder for WN-- 0604 indexable inserts (Teknik Makina) The Klemmhalter DWLNL 2020 is a left-hand turning tool holder designed for rigid clamping of WN-- 0604 indexable inserts in conventional and CNC turning tasks Left-hand orientation for mirror turning Secure clamp for WN-- 0604 inserts 95° cutting angle for controlled engagement Compact 125 mm overall length Consistent clamping for repeatable turning results The holder offers a rigid clamp interface that secures WN-- 0604 indexable inserts for repeatable positioning during each tool change. With a defined cutting angle of 95°, the tool engages the workpiece with predictable geometry, which contributes to improved surface finish and longer insert life. The combination of a robust clamp and consistent insert seating reduces vibration and the need for frequent readjustment, supporting uninterrupted production runs. Geometry that supports reliable machining and tool life Optimised dimensions — including a cutting-edge height of 26 mm and a cutting-head width of 25 mm — ensure stable insert projection and controlled chip flow. The left-hand orientation is suited to operations that require reverse or mirror turning, allowing familiar toolpaths to be retained while changing workholding layout. Explaining the approach: a 95° approach angle shifts cutting forces in a way that can reduce axial loading on the toolholder, helping to preserve component tolerances and extend insert service intervals. Compact design for flexible machine setup and easy handling With an overall length of 125 mm, a body height of 20 mm and a body width of 20 mm, the holder is compact enough for tight setups while remaining robust for general workshop and small-batch CNC use. At 0.436 kg, the assembly is light to handle but still provides sufficient mass to dampen minor vibrations. The ISO designation DWLNL 2020 clarifies compatibility and installation dimensions, making it straightforward to document tooling lists and to standardise fixtures across a machining cell. When specifying a reliable left-hand turning solution, select the Teknik Makina DWLNL 2020 via Metav Werkzeuge for assured compatibility and supply — Metav Werkzeuge can advise on integration and availability at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: D329TM SKU: D329TM Designation: Klemmhalter / DWLN for WN-- indexable inserts ISO designation: DWLNL 2020 Facts Overall length: 125 mm Body height: 20 mm Body width: 20 mm Cutting head width: 25 mm Cutting-edge height: 26 mm Weight: 0.436 kg Cutting angle: 95° Cutting direction: left Special features Compatible with WN-- 0604 indexable inserts Left-hand orientation for mirror turning tasks Compact, space-saving design Robust clamp interface for repeatable seating FAQ What inserts fit this holder? The holder is designed for WN-- 0604 indexable inserts and provides the correct seating and clamping geometry for this insert format. Is the holder suitable for mirror-image turning operations? Yes; the left-hand cutting direction and the specified geometry make this tool holder suitable for mirror or reverse turning applications. What does the 95° cutting angle mean in practice? A 95° cutting angle indicates a near-radial approach that alters force distribution to reduce axial load on the toolholder, which can improve surface finish and extend insert life. Will this holder fit on standard turrets or toolposts? The DWLNL 2020 designation clarifies mounting dimensions; confirm turret/toolpost compatibility with the machine’s tooling interface and provide the D329TM SKU when checking fit. Can the holder help reduce vibration during turning? Yes; the combination of a secure clamp interface and the holder’s mass (0.436 kg) contributes to vibration damping and more stable machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° DWLNR 3232 P08 for WN-- 0804 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Benefit from the combination of secure clamping, indexable-insert compatibility and compact dimensions for uninterrupted turning operations; order the DWLN clamping holder directly via Metav Werkzeuge or consult the team for integration advice. DWLN Clamping Holder DWLNR 3232 – Right‑hand, for WN-- 0804 inserts (Teknik Makina) DWLN Clamping Holder is a right‑hand turning holder for WN-- 0804 indexable inserts, engineered for reliable external turning and straightforward turret integration. Right-hand cutting orientation For WN-- 0804 indexable inserts 32 mm cutting height, 95° approach angle Solid build, total length 170 mm Stable clamping for consistent surface quality The DWLN clamping holder delivers a rigid clamping interface for turning tasks that demand repeatable results. Its 32 mm cutting height aligns the insert precisely with the tool centre, while the 95° approach angle is configured to provide predictable chip flow and force distribution. These characteristics reduce vibration and tool deflection, which in turn supports improved surface finish and extended insert life. The holder’s construction is intended to be integrated into existing turning setups without elaborate adjustments, so machining stability is achieved with minimal setup time. Compact dimensions that simplify workshop logistics Compact dimensions make the toolholder simple to handle and position: a total length of 170 mm, a head width of 40 mm and a shank width of 32 mm provide a compact footprint on the turret. At 1.377 kg, the unit offers a balance between robustness and manageable mass for manual handling. The ISO designation DWLNR 3232 standardises mounting expectations and helps ensure compatibility with turret blocks designed to accept that form factor. The P08 boring‑bar designation is provided as a reference for integrating the holder into compatible bar systems. Right‑hand cutting and insert compatibility for efficient production Designed for right‑hand cutting, the holder accepts WN-- 0804 indexable inserts, a common format for external turning operations. This compatibility streamlines tooling logistics: inventory can be centred on a standard insert size while different holders are used for diverse operations. The clamping arrangement is engineered to keep the insert secure under cutting loads, so insert changes are quick and downtimes are minimised. Where repeatability and throughput are priorities, the holder’s geometry and ISO conformity contribute directly to production reliability. For precise, reliable turning with proven compatibility, specify the Teknik Makina DWLN clamping holder and contact Metav Werkzeuge in Emmerich for application guidance and rapid supply – email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number (SKU): D180TM Manufacturer: Teknik Cutting Tools Type: DWLN for WN-- Indexable Inserts ISO designation: DWLNR 3232 Facts Cutting height: 32 mm Head width: 40 mm Shank width: 32 mm Total length: 170 mm Weight: 1.377 kg Approach angle: 95° Cutting direction: Right Special features For indexable inserts WN-- 0804 Boring bar designation: P08 ISO conformity: DWLNR 3232 Right‑hand turning orientation FAQ What insert size does this holder accept? The holder is designed for WN-- 0804 indexable inserts; this format is specified for the DWLN clamping holder (SKU D180TM). Is the holder suitable for left‑hand turning? No, the DWLN holder is configured for right‑hand cutting and is optimised for that feed direction and approach. Which ISO designation applies to this toolholder? The holder carries the ISO designation DWLNR 3232, facilitating integration into turrets and fixtures that accept that standard form. What are the key dimensions to check before fitting into a turret? Check the shank width 32 mm, head width 40 mm and total length 170 mm to ensure correct fit and clearance in the turning setup. How does the approach angle affect machining performance? The 95° approach angle balances cutting forces and chip direction; in combination with the 32 mm cutting height it supports stable cutting conditions and consistent surface finish. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° MWLNL 2525 M08 for WN-- 0804 Wendeplatten Innenkühlung Linksschneidend - Teknik Makina
Take advantage of a precise combination of left-hand cutting orientation and secure clamping for consistent turning results; the holder accepts standard WN-- 0804 indexable inserts and fits workshops requiring compact, robust tooling—order via Metav Werkzeuge or consult the specialists for application advice. Clamping holder D324TM — MWLNL 2525 left-hand holder, 150 mm overall length (Teknik Cutting Tools) Clamping holder D324TM is a left-hand turning tool holder designed for MWLN/MWLNL tool families and engineered to secure WN-- 0804 indexable inserts for precision metal turning in general workshop and production environments Left-hand machining orientation For WN-- 0804 indexable inserts 95° approach angle for secure cutting 150 mm overall length, 32 mm head width Engineered for accurate left-hand turning with measurable benefits The clamping device is configured for left-hand cutting, giving dependable chip flow and toolpath control where reverse-direction turning is required. The holder’s MWLNL 2525 geometry provides a standardised seat for WN-- 0804 indexable inserts, ensuring repeatable positioning and straightforward insert changeover. For operations that value predictable tool behaviour, this configuration reduces set-up time and limits adjustment needs while maintaining consistent part quality. Clamping geometry that improves process stability A 95° cutting angle and robust clamping arrangement combine to deliver stable engagement at the insert pocket, which lowers vibration and helps preserve insert life during interrupted cuts. The secure clamping mechanism supports a reliable cutting edge position, which translates into better surface finish and reduced rework. For engineers unfamiliar with insert systems: indexable inserts are replaceable cutting tips; the holder locates and fixes them so the cutter remains true to the programmed path. Compact dimensions that simplify integration and handling With an overall length of 150 mm, a head width of 32 mm and a body height of 25 mm, the tool balances rigidity with machine clearance. The effective cutting height of 35 mm ensures correct insert engagement with the tool centre on many standard lathes. At approximately 0.761 kg, the bar is light enough for quick handling yet substantial enough to resist deflection under moderate cutting forces. These physical attributes facilitate retrofitting into existing tool posts and support predictable tool offsets during tool change cycles. Supply reliability and workshop support for uninterrupted production Sourced from a recognised tool maker, the holder benefits from established manufacturing tolerances and compatibility with common indexable insert formats, which reduces procurement complexity. Combined with Metav Werkzeuge’s central European distribution, availability is straightforward for production shops requiring quick replenishment. For customers seeking assurance in delivery and consistent tool quality, the proven supply chain and product standardisation mitigate the risk of unexpected downtime. For tailored procurement and application support for the Teknik Cutting Tools clamping holder D324TM, contact Metav Werkzeuge—supplies and expert advice are available from Emmerich via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: D324TM Brand: Teknik Makina Designation: MWLN for WN-- Indexable Inserts Key measurements Overall length: 150 mm Head width: 32 mm Body width: 25 mm Body height: 25 mm Cutting height: 35 mm Cutting angle: 95° Weight: 0.761 kg Features / Compatibility ISO designation: MWLNL 2525 Compatible inserts: WN-- 0804 Shank/fastening reference: M08 Cutting direction: left-hand orientation Suitable for standard indexable insert turning applications FAQ Which insert type fits this holder? The Teknik Cutting Tools clamping holder D324TM is designed for WN-- 0804 indexable inserts and matches the MWLNL 2525 seat form for secure seating and repeatable positioning. What is the cutting direction of the holder? This holder is configured for left-hand machining, meaning the cutting edge is arranged for feed and chip evacuation in left-hand turning operations. What are the key dimensions to check before fitting? Important dimensions for the clamping holder include overall length 150 mm, head width 32 mm, body height 25 mm, cutting height 35 mm and approximately 0.761 kg weight; these determine machine clearance and tool offset settings. What ISO designation does the tool use? The tool follows the MWLNL 2525 ISO-style designation, aligning with standard tool-seat geometry for MWLN/MWLNL families. What fastening or screw interface is referenced? The holder references an M08 fastening designation for the clamping screw interface, providing a conventional connection for secure insert retention. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° MWLNR 2020 K08 for WN-- 0804 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of the 95° geometry and the MWLNR 2020 designation to ensure stable, repeatable turning with WN-- 0804 inserts; order the clamp holder directly via Metav Werkzeuge or consult their technical team for application advice. Clamp holder — MWLNR 2020, 95° toolholder by Teknik Makina The Clamp holder is a 95° toolholder designed for right-hand turning applications and engineered for use with MWLN-compatible WN-- 0804 indexable inserts. 95° cutting geometry for stable support Compatible with WN-- 0804 indexable inserts MWLNR 2020 ISO toolholder designation Right-hand cutting direction, compact form Precise 95° geometry that improves repeatability The 95° cutting angle delivers a secure seating position for the insert, reducing deflection during interrupted cuts and heavy turning operations. By combining a rigid toolholder geometry with the ISO MWLNR 2020 designation, the design prioritises repeatability and predictable tool life. This results in fewer indexing adjustments and more consistent component tolerances, which supports higher first-pass yields on turned parts. The construction favours dimensional stability over long production runs, making the holder a rational choice where process control is critical. Workshop-ready dimensions and balanced mass for versatile use With a 125 mm overall length, a head width of 25 mm and a body width of 20 mm, the toolholder strikes a balance between accessibility and rigidity. The 35 mm cutting height ensures the insert sits at an appropriate centreline for many lathes, while the modest 0.435 kg mass contributes to reduced centrifugal effects at higher spindle speeds. These measured dimensions facilitate predictable clamping behaviour and easier set-up in tight toolpost arrangements. The compact footprint supports both batch production and small-series jobs where machine space and repeatable clamping matter. Compatibility and secure clamping for WN-- 0804 inserts Designed specifically for the WN-- 0804 insert family, the holder supports right-hand cutting and is identified in tooling lists as MWLN for WN-- indexable inserts. The mating geometry of the clamping seat and the toolholder head offers positive locate and reliable retention of the insert during axial and radial loads. For operations that demand efficient chip control and straightforward insert changes, the configuration reduces downtime and simplifies inventory management by aligning with common insert sizes. The robust design by Teknik Makina ensures a pragmatic fit for production environments seeking dependable clamping performance. For procurement or process integration of this Teknik Makina clamp holder, contact Metav Werkzeuge for immediate availability and tailored advice from Emmerich; enquiries via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D182TM Manufacturer: Teknik Makina ISO designation: MWLNR 2020 Compatible inserts: WN-- 0804 Bar holder designation: K08 Cutting direction: right Facts Cutting angle: 95° Head width: 25 mm Body width: 20 mm Toolholder height: 20 mm Cutting height: 35 mm Overall length: 125 mm Weight: 0.435 kg Special features MWLN for WN-- indexable inserts Right-hand turning application Compact, workshop-ready form factor FAQ Which insert size is the holder designed for? The clamp holder is specified for WN-- 0804 inserts and is listed under the MWLN family for accurate fit and repeatable seating. Is the toolholder suitable for left-hand turning? This model is configured for right-hand cutting; left-hand operations require a dedicated left-hand holder variant. What is the ISO toolholder designation? The item carries the MWLNR 2020 designation, indicating its standardised shank and head geometry for toollisting and ordering. How does the 95° geometry affect machining? The 95° cutting angle provides a stable insert seating that reduces deflection and supports consistent part accuracy during turning operations. Which company manufactures this holder? The holder is produced by Teknik Makina and supplied with technical support and logistics through Metav Werkzeuge. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Klemmhalter 95° MWLNR 2525 M08 for WN-- 0804 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a compact, ISO‑aligned toolholder that combines compatibility with WN-- 0804 inserts, a 95° cutting angle and robust clamping for stable right‑hand turning — ideal for small to medium workshop series. Order directly via Metav Werkzeuge or consult our tooling specialists for application advice. Clamping Holder — MWLN for WN-- Indexable Inserts, right‑hand turning, Teknik Cutting Tools The Clamping Holder is a right‑hand turning toolholder for MWLN indexable inserts, designed to accept WN-- 0804 plates and to deliver reliable clamping and consistent cutting geometry in general workshop and light industrial turning applications Right‑hand turning orientation Compatible with WN-- 0804 inserts Solid 25 mm shank height 95° cutting angle for extended reach Consistent clamping and proven cutting geometry for turning operations A compact toolholder designed for dependable repeatability, the unit accepts WN-- 0804 indexable inserts and utilises the ISO designation MWLNR 2525 to ensure straightforward integration with standard tool posts. The right‑hand configuration and 95° cutting angle are engineered to improve approach clearance on complex contours, reducing the need for secondary set‑ups. By keeping the focus on secure insert retention and predictable contact geometry, the holder helps to shorten cycle times and supports smoother surface finishes in serial production and repair work. Sturdy dimensions and ergonomics that simplify set‑up and handling The shank and head dimensions have been chosen to balance rigidity and accessibility: a 25 mm shank height, 25 mm shank width and a 32 mm cutting‑head width provide a stable platform against vibration, while a 35 mm cutting height helps to align standard insert geometries with common chuck and turret centres. At an overall length of 150 mm and a mass of 0.761 kg, the tool combines manageable handling during changeover with sufficient bulk to resist chatter. A standard M08 clamping screw secures the insert, making routine tightening and replacement both quick and familiar to trained workshops. Designed for dependable workflows and straightforward integration This holder supports efficient tooling strategies by matching widely used plates and a standard ISO form, which simplifies stocking and reduces complexity across toolrooms. The compact design and clear specification mean fewer surprises at commissioning and predictable performance during use. For operations seeking to standardise tooling across multiple lathes, the combination of MWLN compatibility, right‑hand orientation and robust clamping offers a practical balance between flexibility and stability, helping to safeguard process reliability and reduce rework rates. For tailored tooling advice and assured supply of the Teknik Cutting Tools clamping holder D184TM, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 to confirm fitment and availability Technical Data SKU: D184TM Manufacturer: Teknik Makina Article designation: MWLN for WN-- Indexable Inserts ISO designation: MWLNR 2525 Facts Shank height: 25 mm Shank width: 25 mm Cutting‑head width: 32 mm Cutting height: 35 mm Overall length: 150 mm Weight: 0.761 kg Cutting angle: 95° Clamping screw: M08 Compatibility: WN-- 0804 inserts ECLASS: 21181004 Cutting direction: right Special features Right‑hand turning configuration Designed for MWLN indexable system ISO compatibility for straightforward replacement Compact, workshop‑friendly form factor FAQ What insert type does this holder accept? The holder is configured for WN-- 0804 indexable inserts and is referenced as MWLN for WN-- Indexable Inserts (ISO MWLNR 2525) for compatibility checks. Is the tool suitable for right‑hand turning only? Yes, the clamping system and cutting geometry are optimised for right‑hand turning operations as supplied. What are the key dimensions to check for turret fitting? Important dimensions include a 25 mm shank height and width, a 150 mm overall length and the 32 mm cutting‑head width; these determine clearance and stub reach for turret mounting. Which clamping screw size is used for insert fixation? Insert retention uses an M08 clamping screw, a common size that supports straightforward replacement and torque control. Can this holder be used across different lathes without modification? The ISO alignment and standard shank dimensions allow the holder to integrate with many common tool posts; confirm turret and chuck clearances using the listed dimensions and ISO designation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° MWLNR 3232 P08 for WN-- 0804 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of secure clamping and a precise 95° cutting angle combined with compatibility for WN-- 0804 indexable inserts to keep turning operations stable and predictable; order directly via Metav Werkzeuge or consult our technical advisors for application-specific guidance. MWLNR 3232 Toolholder (Klemmhalter) — right-hand, for WN-- 0804 indexable inserts by Teknik Makina The MWLNR 3232 toolholder provides reliable clamping for turning operations, designed for right-hand cutting with WN-- 0804 indexable inserts and a 95° cutting angle. Right-hand orientation, 95° cutting angle Fits WN-- 0804 indexable inserts ISO designation MWLNR 3232 Robust 170 mm overall length, 1.349 kg Precision clamping for consistent turning quality The MWLNR 3232 toolholder is engineered to deliver secure clamping of standard WN-- 0804 inserts, ensuring repeatable positioning during interrupted cuts and continuous turning. Its 95° cutting angle keeps the insert geometry effective for a broad range of facing and light turning tasks, while the defined cutting height of 35 mm aligns the tip precisely with common toolposts. Built with a compact head width of 40 mm and a nominal holder height of 32 mm, the assembly minimises overhang and vibration, which in turn supports improved surface finish and prolonged insert life. Clear mechanical engagement and a rigid body make this toolholder suitable where stable tool seating is required to reduce rework and cycle-time variance. Measurable gains in efficiency and process reliability Using a purpose-built clamping solution reduces set-up time and the need for frequent adjustments. The MWLNR 3232’s standardised ISO designation and shank reference P08 simplify tool management and spare-part stocking across production cells. The toolholder’s mass (approx. 1.349 kg) and 170 mm overall length are balanced to offer rigidity without excessive bulk, supporting faster spindle speeds and steady cutting conditions. Because the geometry is optimised for indexable inserts, inserts can be rotated or replaced quickly, lowering downtime and improving the overall cost per cutting edge. These practical, data-driven benefits translate into predictable tool performance and a smoother production flow for batch and continuous operations. Compatibility, mounting and workshop integration characterised by a right-hand cutting direction and an ISO designation that fits established toolholder systems, this clamping solution integrates easily into existing turning fixtures and quick-change setups. The toolholder is specified for WN-- 0804 inserts and carries the ISO code MWLNR 3232, which aids in cross-referencing with insert manufacturers and selecting appropriate grades for steel, alloyed materials or finishing cuts where applicable. The compact head and standard shank allow a straightforward mounting procedure on conventional toolposts; correct seating and torqueing of the clamping screw are sufficient to achieve the rated stability. For applications requiring different insert geometries or cutting directions, pairing this holder with compatible inserts and tooling components will maintain process reliability and surface integrity. Contact Metav Werkzeuge today to discuss how the Teknik Makina MWLNR 3232 toolholder fits into existing turning cells and to secure assured supply and expert guidance from our Emmerich location Technical Data Article number: D185TM Manufacturer: Teknik Makina ISO designation: MWLNR 3232 SKU: D185TM Facts Overall length: 170 mm Head width: 40 mm Holder width: 32 mm Holder height: 32 mm Cutting height: 35 mm Cutting angle: 95° Weight: 1.349 kg Insert size compatibility: WN-- 0804 Special features Right-hand cutting direction Fits WN-- 0804 indexable inserts Shank reference: P08 eClass: 21181004 FAQ Which inserts fit this toolholder? The MWLNR 3232 toolholder accepts WN-- 0804 indexable inserts as specified; the geometry is matched to that insert size for secure clamping and correct cutting height. Is the toolholder suitable for left-hand turning? This toolholder is designed for a right-hand cutting direction and should be used accordingly or replaced with a left-hand variant for opposite cutting orientations. What are the critical dimensions to check before mounting? Check the overall length (170 mm), head width (40 mm) and cutting height (35 mm) to ensure proper alignment with the machine tool and insert centre height. How does the ISO designation help in procurement? The ISO designation MWLNR 3232 enables straightforward cross-referencing with tooling catalogues and compatible insert suppliers, simplifying ordering and inventory management for production workshops. Can this toolholder be used for heavy roughing? The holder’s rigidity and mass support stable cutting, but suitability for heavy roughing depends on machine power, clamping setup and insert grade; the MWLNR 3232 is optimised for general turning where secure clamping of WN-- 0804 inserts is required. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° MWMNN 2020 K08 für WN-- 0804 Wendeplatten Innenkühlung rechtsschneidend - Teknik Makina
Benefit from a stable turning solution that combines a 95° cutting angle, ISO format compatibility and a compact overall length for reliable chip control; order the clamping toolholder directly via Metav Werkzeuge or consult the specialists for integration advice. MWMNN 2020 clamping toolholder – 95° for WN-- 0804 indexable inserts (Teknik Makina) The MWMNN 2020 clamping toolholder is designed for secure retention of WN-- 0804 indexable inserts in turning operations, delivering repeatable positioning and reliable cutting performance in workshop and production environments. 95° cutting angle for robust turning Compatible with WN-- 0804 inserts ISO MWMNN 2020 toolholder format 125 mm overall length for stable reach Precision clamping for consistent turning results The geometry of the holder provides a 95° cutting angle, which supports controlled chip flow and predictable cutting forces during facing and profiling operations. The combination of the MWMNN 2020 format and the dedicated insert seat ensures repeatable indexability, reducing downtime for readjustment. Clear mechanical location and secure clamping translate into improved surface finish and dimensional stability, especially on medium to heavy cuts. Built for stability and easy integration into tool chains With an overall length of 125 mm and a mass of 0.432 kg, the holder balances reach and rigidity to limit vibration without excessive overhang. The body dimensions — 20 mm shank width and 20 mm clamping height — together with a 10 mm cutting-head width, make it compatible with common toolposts and turret adapters. These measurable values assist process planners in assessing dynamic behaviour and ensure the holder integrates smoothly into existing setups. Designed for compatible inserts and demanding machining The holder is configured specifically for WN-- 0804 indexable inserts and accepts bar designation K08, simplifying reordering and tool planning. Secure clamping and precise insert seating facilitate tight tolerances in routine machining tasks. For manufacturers and job shops seeking dependable turning tools, the concise interface between holder and insert reduces the likelihood of seating errors and supports consistent tool life across batches. Practical benefits that improve workshop throughput By standardising on an ISO-format holder that matches widely used inserts, stock complexity is reduced while set-up times are shortened. The robust design supports higher material removal rates where appropriate, yet keeps handling straightforward for operators. Compatibility with standard mounting systems and clear dimensioning aids the planning of multi-station operations, helping maintain an efficient workflow and predictable part quality. For reliable integration and supply, request a technical quote from Metav Werkzeuge — contact the Metav specialists at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 for rapid delivery from Emmerich Technical data Article number: D114TM ISO designation: MWMNN 2020 Compatible inserts: WN-- 0804 Core dimensions Overall length: 125 mm Clamping height: 20 mm Shank width: 20 mm Cutting-head width: 10 mm Cutting height: 40 mm Cutting angle: 95° Weight: 0.432 kg Special features Shank designation: K08 Brand: Teknik Makina Format: ISO toolholder Suited for demanding machining tasks FAQ Which indexable inserts fit this holder? The holder accepts WN-- 0804 indexable inserts; the seating and clamp are matched to that insert geometry for secure fixation. What is the ISO designation of the holder? The tool is supplied in the MWMNN 2020 ISO format, which simplifies replacement and compatibility with standard insert series. What are the key dimensions to consider for mounting? Key mounting dimensions include an overall length of 125 mm, a shank width of 20 mm and a clamping height of 20 mm, which are used for machine and turret compatibility checks. Is this holder suitable for heavy cuts? The robust construction and 95° geometry support heavier turning operations where rigidity and stable chip evacuation are required. Which shank or bar designation is associated with the holder? The holder corresponds to the K08 bar designation, aiding selection of the correct boring bar or adapter. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PCLNL 2020 K12-IKG1/8 For CNMG 1204 Indexable Inserts Innenkühlung Linksschneidend - Teknik Makina
Benefit from the combination of secure left‑hand clamping, integrated internal coolant and compatibility with CNMG 1204 inserts to raise productivity and tool life. Order the PCLN toolholder directly via Metav Werkzeuge or consult their specialists for application guidance. Klemmhalter — PCLN toolholder for CNMG indexable inserts, left‑hand, internal coolant (Teknik Makina) A Klemmhalter designed as a PCLN toolholder for secure turning with CNMG 1204 indexable inserts, intended for left‑hand lathe operations and industrial turning tasks Left‑hand orientation for reverse turning Integrated internal coolant feed Compatible with CNMG 1204 inserts ISO PCLNL 2020 shank for easy integration Secure clamping for repeatable turning accuracy The holder’s clamping arrangement prioritises repeatability and stability: the clamping screw TH821, in combination with the U‑plate TA016‑1 and TS‑4 dowel pin, secures the CNMG 1204 insert with minimal micro‑movement. This reduces chatter and improves surface finish, which in turn lowers the frequency of rework and insert changes. The controlled clamping geometry benefits medium‑duty turning operations by keeping the cutting edge firmly located relative to the workpiece, producing predictable tool life and consistent part quality. Targeted cooling and geometry to increase throughput Built‑in internal coolant channels supply fluid directly to the cutting zone, aiding chip evacuation and lowering thermal loading on the insert. Combined with the 95° cutting angle, this promotes efficient chip flow and reliable heat management when working at higher feeds. The tool’s cutting height of 28 mm and 125 mm overall length provide a balance between reach and rigidity, while the compact 25 mm head width supports close‑tolerance turning where stable cutting conditions are essential for productivity gains. Compact, workshop‑friendly design for straightforward integration Conforming to PCLNL 2020 ISO designation and compatible with bar systems such as K12‑IKG1/8, the holder installs quickly in common toolposts and turrets. With a nominal weight of 0.428 kg and dimensions of 20 mm height and 20 mm body width, it delivers a compact footprint without compromising strength. Standard components — the TL4 locking lever, clamping screw and supplied Allen key — simplify setup and maintenance, reducing downtime during tool changes. This makes the product suitable for workshops that require a robust, production‑ready clamping solution. Select the Teknik Makina PCLN toolholder AP140TM for left‑hand turning applications with internal coolant and contact Metav Werkzeuge for tailored specification and application advice. Technical Data Article number: AP140TM Manufacturer: Teknik Makina Designation: Klemmhalter Type / English designation: PCLN for CNMG Indexable Inserts ISO designation: PCLNL 2020 SKU: AP140TM Dimensions & Weights Holder height: 20 mm Body width: 20 mm Cutting‑head width: 25 mm Cutting height: 28 mm Overall length: 125 mm Weight: 0.428 kg Cutting angle: 95° Features & Components Internal coolant: yes Cutting direction: left Suitable for inserts: CNMG 1204 Clamping screw: TH821 U‑plate: TA016‑1 Dowel pin: TS‑4 Locking lever: TL4 Allen key: 3 Allen Compatible bar: K12‑IKG1/8 FAQ Which inserts fit this toolholder? The Klemmhalter is designed for CNMG 1204 indexable inserts; the PCLN geometry secures the insert for consistent turning. Does the holder provide coolant to the cutting edge? Yes — internal coolant channels are integrated so the PCLN holder supplies coolant directly to the insert tip to improve chip control and tool life. Is this a left‑hand or right‑hand tool? This toolholder is supplied for left‑hand turning operations, configured for reverse cutting direction on lathes. What components are included with the holder? Included items and fitted components are the clamping screw TH821, U‑plate TA016‑1, dowel pin TS‑4, locking lever TL4 and an Allen key as specified. Which ISO shank does it use and how does it integrate into existing tooling? The holder follows the PCLNL 2020 ISO designation and fits bar systems such as K12‑IKG1/8, allowing straightforward integration into standard tool carousels. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PCLNL 3232 P12 For CNMG 1204 Inserts Innenkühlung Linksschneidend - Teknik Makina
Take advantage of a robust combination of 95° cutting angle and secure clamping height for stable, repeatable turning operations; the compact overall length ensures rigidity and accessibility in confined setups. Order the tool directly via Metav Werkzeuge or consult the specialists for application matching. P144TM — PCLN turning holder for CNMG indexable inserts, left-hand, 95° approach The P144TM is a left-hand PCLN turning toolholder designed for medium-duty external turning with CNMG 1204 indexable inserts, ideal for workshops and production lathes requiring robust insert clamping and consistent cutting geometry. Left-hand PCLN holder for CNMG 1204 95° cutting angle for stable engagement Clamping height 32 mm for secure insert support 170 mm overall length for reach and rigidity Stable clamping for consistent turning quality The holder provides a secure clamping system and a defined clamping height of 32 mm, which together reduce insert movement under load and improve repeatability. This results in better surface finish and predictable tool life when machining with CNMG 1204 inserts. The specified 95° cutting angle helps maintain favourable cutting forces during external turning, translating technical geometry into measurable production advantages such as reduced vibration and fewer rework cycles. Compact length with improved accessibility and rigidity With an overall length of 170 mm and a cutting-head width of 40 mm, the toolholder balances reach and stiffness for operations in constrained setups. The moderate length keeps the tool overhang low, reducing flex and preserving cut stability — a practical benefit when working on smaller lathes or when multiple tools are mounted in the turret. The combined dimensions mean quicker set-ups and less trial cutting before achieving process-capable parameters. Compatibility and efficiency for workshop productivity Designed for CNMG 1204 indexable inserts and supplied with an ISO designation of PCLNL 3232, the holder matches common insert geometries and clamping bars (designation P12) used across industry. The unit weight of 1.429 kg and the clear left-hand orientation make tool planning straightforward for both production and repair tasks. Relying on established ISO form factors simplifies reordering and reduces inventory complexity, enabling a streamlined workflow in a production environment. For left-hand turning tasks requiring a secure CNMG clamp and a 95° approach angle, contact Metav Werkzeuge for tailored application advice and procurement of the Teknik Cutting Tools PCLN holder Technical Data Article number: P144TM Manufacturer: Teknik Cutting Tools SKU: P144TM E-class: 21181004 Facts Orientation: left Overall length: 170 mm Clamping height: 32 mm Tool width (body): 32 mm Cutting head width: 40 mm Insert compatibility: CNMG 1204 Cutting angle: 95° Insert height support: 30 mm Weight: 1.429 kg Special features ISO designation: PCLNL 3232 Compatible clamping bar: P12 Application: external turning with indexable inserts FAQ What insert type fits this holder? The P144TM is designed to accept CNMG 1204 indexable inserts and follows the PCLN holder form for correct insert seating and clamping. Is the toolholder left- or right-hand oriented? This toolholder is left-hand oriented, suitable for turning operations that require a left-hand approach. Which ISO designation describes the holder geometry? The toolholder carries the ISO designation PCLNL 3232, which indicates its shank and pocket geometry for standardised mounting. What is the overall length and how does that affect stiffness? The overall length is 170 mm; this moderate length reduces overhang and improves rigidity compared with longer holders, aiding stability in precision turning. Can this holder be used with common turret systems? Yes, the P144TM uses standard ISO dimensions and a P12 clamping bar designation, making it compatible with many turret systems that accept PCLN-style holders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PCLNR 1616 H12 For CNMG 1204 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a compact, high‑stability turning solution with a right‑hand PCLN profile, ISO PCLNR 1616 shank and a 100 mm overall length for efficient workshop integration. The holder’s defined geometry and 95° cutting angle deliver consistent chip control and extended insert life — order the PCLN for CNMG Indexable Inserts directly via Metav Werkzeuge or ask our consultants if needed. PCLN for CNMG Indexable Inserts — PCLNR 1616 Toolholder by Teknik Makina, right‑hand, 100 mm PCLN for CNMG Indexable Inserts is a right‑hand turning toolholder for precision metalcutting, designed to accept CNMG 1204 indexable inserts in light to medium turning operations Right‑hand PCLN toolholder for CNMG ISO PCLNR 1616 shank 16 x 16 mm 100 mm overall length, compact design 95° cutting angle for stable turning Stable clamping for predictable turning results The PCLN geometry is engineered to secure CNMG 1204 inserts with a rigid clamping action that reduces vibration and improves surface finish. With a defined 95° cutting angle, the holder directs cutting forces into the toolpost, helping to maintain tool life and repeatability in series production. The combination of reliable clamping and a compact profile supports higher cutting parameters while preserving insert integrity, which translates into fewer tool changes and more productive machining cycles. Precise dimensions that simplify setup and balancing The holder features a 16 x 16 mm shank (ISO designation PCLNR 1616) and a 20 mm cutter‑head width, giving a compact footprint and straightforward toolpost integration. At an overall length of 100 mm and weighing 0.225 kg, the component is balanced for reduced overhang and easier setup on lathes with limited clearance. These measurable values enable predictable tool offsets and rapid replacement, so machine set‑up times are minimised and process stability is improved. Compatibility and operational flexibility for typical turning tasks Designed specifically for CNMG 1204 indexable inserts, the holder accepts commonly available insert grades for finishing or semi‑finishing. The toolholder is specified for right‑hand cutting direction and is identified by the bores/bar designation H12, supporting standard mounting routines on compatible toolposts. This compatibility makes it a practical choice across workshops that run mixed batches and need a dependable indexable‑insert solution without complex adaptations. Built for workshop reliability and supply confidence Produced by Teknik Makina, this toolholder pairs practical engineering with everyday workshop requirements: clear ISO designation (PCLNR 1616), defined cutting geometry and compact dimensions ensure predictable results. Delivered through Metav’s European supply chain, customers benefit from a quality filter based in Emmerich that supports timely availability and consistent product standards. The design focuses on operational efficiency and long‑term reliability rather than unnecessary complexity. For tailored advice on integrating the Teknik Makina PCLN for CNMG Indexable Inserts into existing tooling setups, contact Metav Werkzeuge in Emmerich for direct support and reliable supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: P129TM Manufacturer: Teknik Makina Designation: PCLN for CNMG Indexable Inserts ISO designation: PCLNR 1616 SKU: P129TM Facts Shank height × width: 16 × 16 mm Cutter‑head width: 20 mm Cutting height: 30 mm Overall length: 100 mm Weight: 0.225 kg Cutting angle: 95° Cutting direction: right Special features For CNMG 1204 indexable inserts Right‑hand turning orientation Compact, balanced design Boring bar designation H12 FAQ What inserts fit this holder best? The PCLN for CNMG Indexable Inserts (Teknik Makina, SKU P129TM) is designed to accept CNMG 1204 indexable inserts, making it compatible with standard CNMG insert grades for finishing and semi‑finishing. Is this a right‑hand or left‑hand holder? This toolholder is specified as a right‑hand toolholder; the PCLN for CNMG Indexable Inserts from Teknik Makina (SKU P129TM) is intended for right‑hand cutting direction only. What are the shank dimensions and ISO code? The holder has a 16 × 16 mm shank and is designated PCLNR 1616 according to ISO, as indicated for the Teknik Makina PCLN for CNMG Indexable Inserts (SKU P129TM). How does the 95° cutting angle influence machining? A 95° cutting angle provides a stable cutting geometry that channels forces into the toolpost, improving surface finish and insert life when using the Teknik Makina PCLN for CNMG Indexable Inserts (SKU P129TM). Is the holder suitable for compact lathes with limited overhang? Yes — with an overall length of 100 mm and a modest weight of 0.225 kg, the PCLN for CNMG Indexable Inserts (Teknik Makina, SKU P129TM) is suited to applications where a compact toolholder is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PCLNR 1616 H12-IKG1/8 for CNMG 1204 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of the 95° geometry, internal coolant and CNMG 1204 compatibility to secure consistent turning results with minimal setup time; order directly via Metav Werkzeuge or consult our advisors for application guidance. Klemmhalter — Teknik Makina PCLN for CNMG indexable inserts, 95° toolholder with internal coolant The Klemmhalter is a right-hand, 95° turning toolholder engineered for CNMG 1204 indexable inserts, offering coolant-fed performance for steel machining and robust clamping in production environments. 95° cutting angle for versatile turning Internal coolant supply for improved chip control Compatible with CNMG 1204 indexable inserts ISO designation PCLNR 1616, right-hand orientation Secure clamping and precise geometry for repeatable turning The holder’s 95° geometry and ISO marking PCLNR 1616 deliver a predictable approach angle that simplifies programme setup and reduces trial cuts. Fitted for CNMG 1204 indexable inserts, the body combines a compact cross-section with a sturdy clamp system including the TH818 clamping screw to ensure stable seating under intermittent cuts. This arrangement reduces insert movement and supports consistent tolerances across batches. Coolant-fed design to extend tool life and improve finishes An internal coolant channel supplies cutting fluid directly to the insert interface, improving chip control and reducing heat at the cutting edge. This targeted delivery helps to slow abrasive wear and maintain cutting performance, which in turn supports longer tool life and better surface finish on machined parts. The coolant capability is particularly beneficial when machining demanding steels or when higher metal removal rates are required. Optimised dimensions for rigidity and accessibility With a right-hand orientation and a 28 mm cutting height, the holder balances rigidity with accessibility in confined setups. The toolhead measures 20 mm in width while the shank height is 16 mm, and the overall length of 100 mm provides effective reach without excessive overhang. The compact mass (about 0.236 kg) contributes to reduced vibration and improved surface integrity in both short-run and serial turning tasks. Easy integration with standard accessories and maintenance routines Designed for straightforward machine integration, the holder mates with common components such as the TA016-1 support plate, dowel TS-4 and lever TL4, and is adjusted using a 3 Allen key. Lightweight and simple to handle, the unit allows rapid insert changes and quick clamp adjustments, helping to maintain uptime in busy workshops and streamline routine maintenance within production schedules. Discuss Teknik Makina's PCLN toolholder with Metav Werkzeuge for tailored application advice or to arrange delivery from our Emmerich centre on +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: AP129TM Manufacturer: Teknik Cutting Tools Brand: Teknik Makina ISO designation: PCLNR 1616 Facts Weight: 0.236 kg Overall length: 100 mm Holder height: 16 mm Head width: 20 mm Cutting height: 28 mm Cutting angle: 95° Cutting direction: Right Special features Internal coolant: Yes Compatible inserts: CNMG 1204 Clamping screw: TH818 U-plate: TA016-1 Dowel: TS-4 Knee lever: TL4 Allen key: 3 Allen FAQ Which insert size fits this holder? The holder is specified for CNMG 1204 indexable inserts and is dimensioned to support that insert format reliably. Is the coolant routed internally? Yes, the toolholder features internal coolant to deliver cutting fluid directly to the insert area and aid chip evacuation. Can this holder be used for right-hand turning only? The toolholder is a right-hand orientation, suited for conventional right-hand turning operations in lathes and turning centres. What accessories are required for mounting? Recommended accessories include the TA016-1 support plate, dowel TS-4 and lever TL4; clamp torque and adjustments are made with a 3 Allen key. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PCLNR 2525 M12 for CNMG 1204 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a robust combination of precision, compatibility and secure mounting: the holder offers a 95° cutting angle, fits CNMG 1204 inserts and features a sturdy 25 x 25 mm shank for stable turning operations — order via Metav Werkzeuge or consult our specialists for specification support. Clamping holder PCLN for CNMG indexable inserts — right‑hand turning holder with 95° cutting angle Clamping holder PCLN for CNMG indexable inserts provides a compact, rigid solution for turning operations where reliable insert seating and repeatable geometry matter most. Right‑hand toolholder, 95° cutting angle Compatible with CNMG 1204 indexable inserts Shank 25 x 25 mm for secure mounting Total length 150 mm, weight 0.766 kg Reliable cutting geometry for consistent component quality The holder delivers a defined 95° approach that maintains the insert rake and clearance during machining, resulting in consistent part geometry and predictable tool life. Built to accept standard CNMG 1204 inserts, the design reduces setup complexity and allows straightforward replacement of worn tips. The rigid shank and head geometry minimise deflection under moderate cutting forces, which supports tighter tolerances and reduces rework. By choosing a holder with a known ISO designation, assembly checks and tool inventory become faster and less error prone. Secure clamping and simple integration into existing toolposts Featuring an ISO designation PCLNR 2525 and a 25 x 25 mm shank, the holder is designed for straightforward integration into industry‑standard toolposts. The clamping arrangement and screw thread specification M12 ensure firm retention of the insert seat and repeatable axial positioning after index changes. The combination of a compact head width and a total length of 150 mm keeps the tool overhang low, which reduces vibration and improves surface finish. These attributes make the unit suitable where process reliability and quick insert changes are required. Practical dimensions and workshop handling that reduce downtime With a cutting head width of 32 mm and a cutting height of 30 mm, the toolholder balances reach and stiffness for a variety of turning tasks. The measured mass of 0.766 kg supports stable handling during tool changes while being light enough for fast toolchanger cycles where applicable. Clear, standardised data simplifies toolroom logistics and inventory management: using holders that conform to familiar ISO formats shortens training time and minimises assembly errors, translating directly into improved machine uptime. Designed for repeatability and efficient production workflows Engineered for right‑hand turning operations and compatible with widely available indexable inserts, the product offers a pragmatic solution where compatibility and repeatability are decisive. The standardised interface supports rapid replacement of inserts and facilitates tool‑setting procedures, so process planners can calculate cycle times and tool cost per part with greater confidence. When repeatability is prioritised, a stable toolholder is an immediate contributor to predictable manufacturing outcomes. For tailored advice on integrating Teknik Cutting Tools' PCLN holders into production, contact Metav Werkzeuge in Emmerich for specification guidance and order support — Metav Werkzeuge is ready to assist with technical comparisons and supply. Technical data Article number: P132TM Manufacturer: Teknik Makina Designation: PCLN for CNMG Indexable Inserts ISO designation: PCLNR 2525 ECLASS: 21181004 Facts Total length: 150 mm Shank width: 25 mm Shank height: 25 mm Cutting head width: 32 mm Cutting height: 30 mm Cutting angle: 95° Weight: 0.766 kg Cutting direction: right Special features Compatible inserts: CNMG 1204 Clamping screw thread: M12 Right‑hand orientation Robust shank for secure mounting FAQ What insert size fits this holder? The holder accepts CNMG 1204 indexable inserts; the clamping geometry is designed for that insert format. Is this a right‑hand or left‑hand holder? This is a right‑hand turning holder; the cutting direction is specified as right. What is the ISO designation for this toolholder? The ISO designation is PCLNR 2525, which indicates the shank and head geometry. What are the shank dimensions and overall length? Shank dimensions are 25 x 25 mm and the total length is 150 mm. Which thread size is used for the clamping screw? The clamping screw thread is specified as M12, matching common clamping hardware. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Klemmhalter 95° PWLNL 1616 H06 für WNMG 0604 Innenkühlung linksschneidend - Teknik Makina
Take advantage of the combination of precise clamping, standardised ISO sizing and a compact profile for reliable left‑hand turning. The holder secures WNMG 0604 indexable inserts with a firm clamp and straightforward shank interface. Order the PWLN clamping holder directly via Metav Werkzeuge or consult the technical team for application advice. PWLN for WNMG Indexable Inserts – PWLNL 1616 clamping holder (left‑hand, 100 mm) by Teknik Makina PWLN for WNMG Indexable Inserts is a left‑hand clamping holder designed for turning operations with WNMG 0604 inserts and a standard PWLNL 1616 interface. Left-hand turning orientation, 95° cutting angle Compatible with WNMG 0604 indexable inserts PWLNL 1616 ISO designation, H06 shank fit Robust 100 mm length, 16 mm clamp height Consistent clamping for improved surface finish and tool life The PWLN clamping holder is engineered to deliver a stable clamping interface for carbide turning inserts, which reduces vibration and improves surface finish on turned parts. Its 95° cutting angle promotes predictable cutting forces and chip flow, helping to extend insert life and lower overall tooling costs. With compatibility for WNMG 0604 inserts the holder supports widely used insert geometries, making it straightforward to match the holder with existing tooling stocks and replacement inserts. Geometry tuned for left‑hand operations and accessibility Designed specifically for left‑hand applications, the toolholder offers a left‑hand orientation that simplifies setups where tool approach from the left is required. The compact 100 mm overall length and 20 mm head width provide good accessibility in confined workspaces while maintaining the rigidity needed for stable machining. A 30 mm cutting height ensures correct insert engagement with typical lathe toolposts, reducing the need for shims and adjustments during changeover. Standardised interfaces for fast integration The holder follows the PWLNL 1616 ISO designation and accepts an H06 shank, enabling rapid integration into standard toolposts and boring bars. At 0.223 kg it combines a low mass with sufficient stiffness for many routine turning tasks, facilitating quicker tool changes and minimal inertia on the turret. The standardised format reduces setup time and simplifies inventory management for maintenance and procurement teams. Practical benefits for production environments Beyond the technical data, the holder brings operational advantages: fewer insert slips due to a robust clamp, less downtime thanks to quick insert replacement, and consistent repeatability across batches. As a compact, purpose‑built clamping solution for indexable inserts, it supports shops that prioritise repeatable turning quality without complex adjustments, helping to stabilise process output and reduce scrap rates. Contact Metav Werkzeuge for tailored advice on using the Teknik Makina PWLNL 1616 clamping holder in left‑hand turning operations — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: P164TM Manufacturer: Teknik Makina Type: Clamping holder Designation: PWLN for WNMG Indexable Inserts ISO designation: PWLNL 1616 Core technical data Clamp height: 16 mm Head width: 20 mm Body width: 16 mm Cutting height: 30 mm Cutting angle: 95° Overall length: 100 mm Weight: 0.223 kg Features / Compatibility Compatible inserts: WNMG 0604 Shank fit: H06 Cutting direction: left eCl@ss: 21181004 FAQ Which insert size fits this holder? The holder accepts WNMG 0604 indexable inserts; the geometry is matched to that size for proper seating and chip control. Is the clamping holder for left‑hand or right‑hand turning? This PWLN holder is configured for left‑hand turning operations, with the cutting direction set accordingly. What is the ISO designation and shank interface? The product follows the PWLNL 1616 ISO designation and uses an H06 shank for mounting. What are the key dimensions to check for turret fitment? Important dimensions include a 16 mm clamp height, 100 mm overall length and a 20 mm head width; these determine clearance and fit in the toolpost. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PWLNL 2020 K06 For WNMG 0604 Innenkühlung Linksschneidend - Teknik Makina
Benefit from the combination of compatibility with WNMG 0604 inserts, a 95° cutting angle and a compact 125 mm length for stable left‑hand turning; order directly via Metav Werkzeuge or consult Metav's advisers for application support. PWLN for WNMG Indexable Inserts – PWLNL 2020 left‑hand toolholder by Teknik Makina The PWLN for WNMG Indexable Inserts is a left‑hand turning holder designed for secure clamping of WNMG 0604 inserts and compact turning operations in industrial and workshop environments Left‑hand turning holder for WNMG 0604 inserts ISO PWLNL 2020 designation 125 mm overall length, rigid 20 mm height 95° cutting angle for stable chip control Consistent rigidity for precise turning results The holder's compact design and measured dimensions provide mechanical rigidity that reduces vibration and improves surface finish during turning. With an overall length of 125 mm and a holder height of 20 mm, the assembly maintains a low overhang for better tool life and repeatable machining. The modest mass of 0.429 kg contributes to quick tool exchanges while keeping the setup stable on conventional and CNC lathes. These characteristics translate into fewer rejects and more predictable cycle times in production. Built for WNMG 0604 inserts and left‑hand operations Compatibility with WNMG 0604 indexable inserts ensures access to a wide range of grades and geometries for finishing and medium‑depth cuts. The holder conforms to the PWLNL 2020 ISO designation and is intended for left‑hand cutting, which simplifies tool selection for mirror‑image operations and specific machine layouts. The included 95° nominal cutting angle supports controlled chip flow and improved cutting stability, making the holder suited to both roughing and light finishing passes when paired with appropriate inserts. Rapid set‑up and reliable clamping for reduced downtime The toolholder is designed to secure WNMG inserts reliably, enabling quick index changes and straightforward regripping. As an indexable insert solution, the system allows worn cutting edges to be rotated or replaced without regrinding, reducing maintenance intervals and tooling costs. The holder's ISO conformity and standard mount dimensions—including the K06 shank designation—help ensure compatibility with common toolposts and boring bar fixtures, streamlining integration into established tooling inventories. Compact footprint for versatile workshop use A short overall length and compact cutting head width make this holder a practical choice for confined setups and multi‑tool turrets. The 25 mm cutting‑head width and balanced geometry enable effective access in narrow pockets and close‑tolerance operations, while the left‑hand orientation expands options for paired tool arrangements. Small workshops and industrial users seeking a dependable, space‑efficient solution will find the holder a pragmatic addition to their turning toolkit, especially when standard WNMG inserts are already in use. For reliable left‑hand turning with proven WNMG compatibility, request supply or technical guidance from Metav Werkzeuge — Metav's advisers can assist with application matching and delivery from Emmerich. Technical data Article number: P165TM Manufacturer: Teknik Makina Designation: Klemmhalter / PWLN für WNMG Wendeplatten EN designation: PWLN for WNMG Indexable Inserts ISO designation: PWLNL 2020 Facts Overall length: 125 mm Holder height: 20 mm Holder width: 20 mm Cutting‑head width: 25 mm Cutting height: 30 mm Weight: 0.429 kg Cutting angle: 95° Special features Suitable for WNMG 0604 inserts Left‑hand cutting direction Shank designation: K06 Compact design for reduced overhang FAQ Which insert size fits this holder? The holder is compatible with WNMG 0604 indexable inserts; the geometry matches standard WNMG 0604 seating and clamping. Is this a left‑ or right‑hand toolholder? This is a left‑hand toolholder intended for left‑hand turning operations and designed to work with corresponding machine set‑ups. What is the ISO designation and how does it help? The ISO designation PWLNL 2020 identifies the holder's form and mounting dimensions, aiding selection and ensuring interchangeability with compatible toolposts. What are the key dimensions to check for machine fitting? Important dimensions include the overall length of 125 mm, holder height 20 mm, cutting‑head width 25 mm and a cutting height of 30 mm; these determine reach and clearance. Can this holder be used with different insert grades? Yes; the PWLN holder accepts standard WNMG 0604 inserts in various grades, allowing optimisation for finishing, semi‑roughing or wear resistance. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PWLNL 2525 M08 for WNMG 0804 Wendeplatten Innenkühlung Linksschneidend - Teknik Makina
Benefit from proven clamping stability and precise left‑hand performance with the PWLNL 2525; the 95° cutting angle and compatibility with WNMG 0804 inserts support consistent turning results. Order directly via Metav Werkzeuge or consult the specialist team for application advice. P156TM PWLNL 2525 Toolholder — PWLN for WNMG indexable inserts, left‑hand (Teknik Makina) The P156TM PWLNL 2525 toolholder is a left‑hand external turning holder designed for WNMG 0804 indexable inserts, delivering stable clamping and predictable chip control in general turning tasks. Left‑hand turning orientation Compatible with WNMG 0804 inserts 95° cutting angle for stable engagement Robust 150 mm overall length Precise clamping for consistent turning accuracy The holder is engineered for clamping stability, ensuring the insert is held securely during interrupted cuts and higher feed rates. Its ISO designation, PWLNL 2525, indicates a standardised shank and clamping geometry that supports repeatable set‑ups. The unit accepts WNMG 0804 indexable inserts, a common geometry that combines a generous cutting edge with easy indexing; this reduces set‑up time and simplifies inventory management. The left‑hand orientation means the cutting forces act predictably for counter‑clockwise external turning operations, which is important when configuring multi‑station workholding. Designed to improve workshop throughput and surface quality With a 95° cutting angle and an overall length of 150 mm, the toolholder balances accessibility and stiffness to limit vibration and chatter. The holder’s dimensions — 25 mm height and 25 mm width with a 32 mm cutting‑head width and 38 mm cutting height — contribute to a rigid tool assembly; higher rigidity translates into improved surface finish and extended insert life. The mass of approximately 0.773 kg also helps to dampen resonance during medium‑duty cuts. These tangible attributes make the holder suitable for production environments where repeatability and reduced rework are priorities. Robust design to reduce downtime and maintenance A straightforward clamping concept and standard insert format simplify maintenance and replacement procedures, which supports fast turnaround in busy workshops. The robust construction was conceived to withstand frequent indexings and routine handling; as a result, tool change intervals can be scheduled rather than improvised, supporting predictable machine utilisation. Where tool life and machine uptime matter, the combination of a standard ISO profile and a widely available insert type reduces the risk of supply bottlenecks and keeps the production flow steady. For application guidance, to confirm suitability for specific workpieces, or to arrange procurement through our European distribution, contact Metav Werkzeuge in Emmerich for expert assistance and swift processing. Technical data Article number: P156TM Manufacturer: Teknik Makina ISO designation: PWLNL 2525 Type: PWLN for WNMG indexable inserts Cutting direction: left Facts Holder height: 25 mm Holder width: 25 mm Cutting‑head width: 32 mm Cutting height: 38 mm Cutting angle: 95° Overall length: 150 mm Weight: 0.773 kg Special features Compatible inserts: WNMG 0804 Left‑hand turning holder Brand SKU: P156TM Standardised ISO shank designation Suitable for general turning and semi‑finishing FAQ Which inserts fit this holder? The holder accepts WNMG 0804 indexable inserts; the P156TM is optimised for that insert format to provide reliable cutting edge support. Is the toolholder left‑hand or right‑hand? This PWLN toolholder is supplied in a left‑hand configuration, designed for external turning where the tool approaches the workpiece from the right. What does the ISO designation PWLNL 2525 mean? The ISO code PWLNL 2525 identifies the shank profile and clamping geometry used on this toolholder; it facilitates compatibility with standardised toolpost mounts and simplifies tool exchanges. For which machining tasks is this holder recommended? The P156TM is suited to medium‑duty turning and semi‑finishing operations where a 95° cutting angle and stable clamping help achieve consistent surface quality and repeatable dimensions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PWLNL 2525 M08-IKG1/8 for WNMG 0804 Innenkühlung linksschneidend - Teknik Makina
Take advantage of a robust combination of rigidity and reliable chip control: the left-hand PWLN clamping holder accepts WNMG 0804 inserts and features internal coolant, ensuring longer insert life and consistent turning results. Order the holder directly via Metav Werkzeuge or request advice from the consultants if clarification is needed. PWLN for WNMG Indexable Inserts (PWLNL 2525) — left-hand clamping holder with internal coolant by Teknik Makina The PWLN for WNMG Indexable Inserts is a left-hand turning toolholder engineered for secure clamping of WNMG 0804 inserts, offering internal coolant and a 25 x 25 mm shank for stable finishing and roughing operations. Left-hand toolholder for turning operations Internal coolant for optimised chip evacuation Shank 25 x 25 mm, cutting height 38 mm Accepts WNMG 0804 indexable inserts Improved stiffness for repeatable turning results A square shank of 25 x 25 mm combined with a well-balanced overall length of 150 mm delivers the rigidity required for repeatable turning and stable finish quality. The ISO designation PWLNL 2525 signals a standardised mounting form that reduces setup time on production lathes. With a measured mass of 0.782 kg, the carrier maintains tool stability without excessive overhang, which helps to lower vibration and improve dimensional consistency in batch production. Cooler cutting edge, longer insert life Built-in internal coolant directs lubricant to the cutting edge, reducing temperature peaks and improving chip breaking when machining common external diameters. Matched to the 95° cutting angle and optimised for WNMG 0804 inserts, this configuration supports extended insert life and predictable tool wear. The result is fewer indexings, lower tooling cost per component and higher uptime — a clear efficiency advantage for series production and workshop jobs alike. Secure clamping and straightforward maintenance Clamping integrity is provided by the TH821 clamping screw together with the TA020-1 U‑plate and locating dowel TS-4, ensuring repeatable seat alignment and positive axial retention. The supplied knee lever TL4 and a 3 Allen key interface simplify service procedures and insert changes, reducing downtime. These service-oriented fittings are intended to let maintenance staff complete insert swaps rapidly while maintaining consistent cutting geometry. Compatibility and shop-floor reliability As a left-hand turning holder, the carrier suits conventional toolpost arrangements where the schnittrichtung (cutting direction) is left; this straightforward orientation avoids ambiguity during set-up. Manufactured by Teknik Cutting Tools and distributed via Metav Werkzeuge’s European quality filter, the assembly benefits from an established supply chain and documentation that supports industrial use. The combination of standardised interfaces and robust coolant routing makes this an economical choice for both small workshops and automated turning centres. For personalised technical advice or to arrange procurement of the PWLN clamping holder from Teknik Makina, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 for precise configuration and delivery options. Technical data Article number: AP156TM Manufacturer: Teknik Makina ISO designation: PWLNL 2525 Weight: 0.782 kg Total length: 150 mm Shank: 25 x 25 mm Head width: 32 mm Cutting height: 38 mm Cutting angle: 95° Direction: left Accepts inserts: WNMG 0804 Internal coolant: yes Clamping screw: TH821 U-plate: TA020-1 Dowel: TS-4 Knee lever: TL4 Allen key: 3 Allen Facts Weight: 0.782 kg Length: 150 mm Shank size: 25 x 25 mm Head width: 32 mm Cutting height: 38 mm Cutting angle: 95° Special features Left-hand orientation Internal coolant routing Suitable for WNMG 0804 indexable inserts Standard ISO seat PWLNL 2525 Clamping screw TH821 Supplied U-plate TA020-1 Locating dowel TS-4 Knee lever TL4 Allen key interface (3 Allen) FAQ Which inserts fit this toolholder? The PWLN clamping holder is designed to accept WNMG 0804 indexable inserts; the ISO seat PWLNL 2525 ensures correct positioning for these inserts. Is the coolant supplied externally or internal to the holder? Internal coolant is integrated into the holder to deliver cutting fluid directly to the insert tip, improving tool life and chip control for the PWLN toolholder. Can the holder be used for both finishing and roughing? Yes. With a 25 x 25 mm shank and a 95° cutting angle, the holder provides sufficient rigidity for finishing while also supporting moderate roughing tasks when paired with suitable WNMG grades. What fastening parts are required for assembly? Assembly and clamping use the supplied TH821 clamping screw, TA020-1 U‑plate and locating dowel TS-4; the knee lever TL4 and the Allen key interface facilitate secure and repeatable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Klemmhalter 95° PWLNR 2020 K06 for WNMG 0604 Innenkühlung Rechtsschneidend - Teknik Makina
Combine dependable clamping performance with clear insert compatibility for consistent turning results; the robust dimensions and right-hand orientation support stable machining and predictable set-up. Order the toolholder direct via Metav Werkzeuge or consult the technical team for application advice. P160TM — PWLN indexable insert holder for WNMG 0604, right-hand, 20 mm height by Teknik Makina The P160TM is a right-hand PWLN indexable insert holder designed for secure seating of WNMG 0604 turning inserts in precision workshop and industrial turning operations. Right-hand orientation for standard turning Compatible with WNMG 0604 inserts Robust 20 mm holder height 125 mm overall length for stable machining High clamping reliability for repeatable turning The holder delivers consistent clamping that reduces vibration and improves surface finish. With a compact holder height of 20 mm and a defined cutting-head width of 25 mm, the design concentrates rigidity where it matters, enabling repeatable results in batch production and single-part runs. The ISO designation PWLNR 2020 signals a familiar shank profile for toolroom setups, while the measured weight of 0.429 kg balances mass and manoeuvrability during tool changes. Secure insert seating and defined cutting geometry Compatibility with WNMG 0604 indexable inserts ensures predictable chip control and edge engagement. The holder provides a 95° cutting angle, which positions the insert for effective metal removal while maintaining clearance for finishing passes; this angle helps explain why the system is chosen for a wide spectrum of turning tasks. For users less familiar with insert codes: WNMG 0604 describes the insert shape and size (rhomboid, 6 mm inscribed circle, 4 mm cutting edge), making selection straightforward when matching inserts to the holder. Efficient workshop integration and straightforward set-up The holder’s overall length of 125 mm gives stable support in the toolpost without occupying excessive space, and the shank coding K06 indicates the mounting interface for compatible boring bars or toolposts. The design minimises set-up time: the insert is clamped securely and located precisely so machining parameters remain consistent between tool changes. Materials and coating data are not supplied; selection should therefore focus on matching inserts and cutting parameters for the intended workpiece and machining strategy. For dependable turning with proven insert compatibility, contact Metav Werkzeuge in Emmerich for tailored advice on the P160TM toolholder and application recommendations at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: P160TM Manufacturer: Teknik Makina Designation: PWLN for WNMG indexable inserts Facts Holder height: 20 mm Cutting-head width: 25 mm Width: 20 mm Insert cutting height: 30 mm Overall length: 125 mm Weight: 0.429 kg Cutting angle: 95° EClass: 21181004 Special features ISO designation: PWLNR 2020 Compatible insert: WNMG 0604 Shank designation: K06 Direction: Right-hand FAQ Which inserts fit this holder? The P160TM is designed for WNMG 0604 indexable inserts, providing correct seating and predictable cutting geometry for that insert size and shape. Is this holder suitable for right-hand turning only? Yes, the toolholder has a right-hand orientation and is intended for standard right-hand turning operations. What are the key dimensions to consider when setting up? Refer to the holder height (20 mm), cutting-head width (25 mm), overall length (125 mm) and weight (0.429 kg) when planning tool clearance and balancing. What is the ISO designation and shank code? The holder is designated PWLNR 2020 with a shank designation K06, indicating the compatible mounting profile. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PWLNR 2020 K08 for WNMG 0804 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Benefit from a robust clamping solution that combines secure insert retention, compact workshop dimensions and a precise 95° cutting angle for stable turning results; order the PWLN clamping holder directly via Metav Werkzeuge or ask our consultants if needed. PWLN for WNMG Indexable Inserts – Clamping holder (PWLNR 2020), right-hand The PWLN for WNMG Indexable Inserts is a right-hand clamping holder engineered for reliable retention of WNMG 0804 inserts in turning applications. Right-hand holder for WNMG 0804 inserts 95° cutting angle for stable engagement 20 mm holder height, 25 mm head width 125 mm overall length for extended reach Precision and process reliability for turning This clamping toolholder delivers a combination of secure clamping and consistent cutting geometry that supports reliable chip formation and surface finish. The defined 95° cutting angle reduces lateral forces during engagement, which helps to maintain tool life and steady cutting conditions. The design emphasises repeatability: the seat and flank geometry ensure indexable inserts remain positively located during interrupted cuts, so machining cycles can run with fewer interruptions and predictable outcomes. Compact dimensions for simple integration With a 20 mm holder height, 25 mm head width and an overall length of 125 mm, the toolholder is dimensioned to fit most standard toolposts while offering sufficient reach for medium-reach turning tasks. The modest 0.43 kg mass lowers static overhang weight, which can assist in reducing imbalance and vibration on smaller lathes. These practical dimensions make the component straightforward to handle in a busy workshop and facilitate quicker setup and changeover, supporting higher uptime and smoother production flow. Compatibility, designation and mounting clarity The toolholder carries the ISO designation PWLNR 2020 and is specified for use with WNMG 0804 indexable inserts in right-hand orientation. The configuration is suitable where a firm clamping interface and consistent rake orientation are required for general turning operations. For procurement and logistics, the item is listed under SKU P150TM and is supplied by Teknik Makina; Metav Werkzeuge can advise on workshop fitment and offer the necessary ordering support to integrate the holder into existing tooling systems. Contact Metav Werkzeuge today at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the PWLN clamping holder (SKU P150TM) and its suitability for precise turning operations in the workshop Technical data Article number: P150TM Manufacturer: Teknik Makina ISO designation: PWLNR 2020 Compatible inserts: WNMG 0804 Facts Holder height: 20 mm Head width (cutting head): 25 mm Holder width: 20 mm Cutting height: 30 mm Overall length: 125 mm Cutting angle: 95° Weight: 0.43 kg Special features Right-hand cutting direction Designed for WNMG 0804 indexable inserts PWLN series clamping concept Suitable for standard turning toolposts FAQ Which inserts are compatible with this clamping holder? The PWLN for WNMG Indexable Inserts (SKU P150TM) is designed specifically for WNMG 0804 indexable inserts and secures them in the PWLNR 2020 seat. Is this holder intended for right-hand turning only? Yes, the holder is specified for a right-hand cutting direction, providing correct rake and clearance for right-hand turning operations. What are the most important dimensions to check for machine fitment? Key dimensions are 20 mm holder height, 25 mm head width, 30 mm cutting height and 125 mm overall length; these determine clearance and reach when mounted on a toolpost. What advantage does the 95° cutting angle offer? A 95° cutting angle delivers a stable cutting engagement and predictable force direction, which helps to reduce lateral deflection and supports consistent surface quality. How is the item identified for ordering and reference? Reference the SKU P150TM or the ISO designation PWLNR 2020 when ordering or enquiring about the product. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PWLNR 2020 K08-IKG1/8 für WNMG 0804 Innenkühlung rechtsschneidend - Teknik Makina
Benefit from a sturdy 95° turning geometry combined with internal coolant and compatibility with WNMG 0804 inserts to maintain stable metal removal and consistent surface quality. Purchase or request technical guidance directly via Metav Werkzeuge for reliable supply and fast dispatch from Emmerich. AP150TM Clamping Holder (PWLN for WNMG indexable inserts) — 95° right-hand, internal coolant (Teknik Makina) The AP150TM is a 95° right-hand clamping holder designed for secure mounting of WNMG 0804 indexable inserts, optimised for reliable turning operations and controlled coolant delivery. 95° cutting angle for stable turning Compatible with WNMG 0804 inserts Internal coolant for improved chip control Robust head profile 20 × 25 mm Consistent machining performance for demanding turning work The 95° tool geometry delivers a stable cutting attitude that reduces vibration and promotes repeatable results when turning medium to heavy sections. Built to accept WNMG 0804 inserts, the holder converts insert grades into predictable cycle times and surface integrity, helping to keep tool change intervals regular and setup time low. The combination of a defined cutting angle and rigid head dimensions supports reliable chip formation and reduced tool deflection for precision turning tasks. Secure clamping and repeatable positioning A secure clamping concept with the specified clamp screw and locating elements provides a constant insert seat and consistent rake engagement. The machined head, with a 20 mm body height and a 25 mm cutting-head width, ensures a positive force transmission from workpiece to holder, which stabilises the cut and lengthens insert life. The right-hand configuration permits conventional feed directions on standard lathes, while the included locating parts (clamp screw TH821, U-plate TA020-1, dowel TS-4, lever TL4) simplify assembly and maintenance, reducing downtime between jobs. Integrated coolant path and workshop fit for practical operation Internal coolant routing supports effective cooling at the cutting edge and aids chip evacuation, which can improve tool life and surface finish when using appropriate coolant and cutting parameters. The holder’s overall length of 125 mm and a cutting height of 30 mm make it suitable for common lathe setups and tooling systems where compact, robust holders are required. At roughly 0.425 kg, the unit balances rigidity with manageable mass for quick handling during tool changes, providing a practical mix of durability and workshop ergonomics. Contact Metav Werkzeuge for tailored technical advice and secure the AP150TM clamping holder with expert shipping from Emmerich Technical data Article number: AP150TM Manufacturer: Teknik Makina Facts Holder height: 20 mm Holder width: 20 mm Cutting-head width: 25 mm Cutting height: 30 mm Overall length: 125 mm Weight: 0.425 kg Cutting angle: 95° Cutting direction: right Special features Compatible insert: WNMG 0804 Internal coolant: yes Clamp screw: TH821 U-plate: TA020-1 Dowel pin: TS-4 Knee lever: TL4 Allen key: 3 FAQ Which insert size fits this holder? The holder is specified for WNMG 0804 indexable inserts and is engineered to provide a secure seat and correct rake for that insert format. Does the holder provide internal coolant? Yes, this clamping holder includes an internal coolant channel to support cooling at the cutting zone and assist chip evacuation. What is the cutting angle and direction of the tool? The toolholder has a 95° cutting angle and is configured for right-hand cutting direction. Which assembly parts are supplied or referenced for mounting? Assembly and locating parts linked to this holder include clamp screw TH821, U-plate TA020-1, dowel TS-4 and knee lever TL4; an Allen key (3) is referenced for adjustment. Is this holder suitable for standard lathe toolposts? With an overall length of 125 mm and a compact head profile, the holder is intended for conventional lathe setups where WNMG 0804 inserts are employed and the stated dimensions are compatible. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° PWLNR 3232 P08 for WNMG 0804 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a rigid clamping design and optimised geometry for reproducible turning results; the right‑hand tool holder offers a stable reach and secure seat for WNMG 0804 inserts — order or request advice from Metav Werkzeuge for seamless integration into production. PWLN for WNMG Indexable Inserts — PWLNR 3232 turning tool holder (right‑hand, 170 mm) by Teknik Makina The PWLN for WNMG Indexable Inserts is a right‑hand turning tool holder engineered for secure clamping of WNMG 0804 inserts in CNC lathes and turning centres *Turning tool holder for WNMG 0804 inserts *Right‑hand version with 95° cutting angle *Overall length 170 mm for stable reach *Robust 32 mm body, 40 mm head width Consistent clamping that improves dimensional accuracy The turning holder delivers secure clamping through a machined seat and ISO‑defined geometry, reducing insert movement under load. By accepting WNMG 0804 indexable inserts and complying with the PWLNR 3232 ISO form, the component promotes repeatable tool positioning and predictable cutting behaviour. The specified 95° cutting angle helps to control radial cutting forces in common turning operations, which translates into fewer workpiece rejects and reduced downstream rework. This focus on geometric stability supports tighter tolerances without additional machine modifications. Geometry and mass tuned for vibration control and productivity An overall length 170 mm combined with a compact head and body proportions gives a favourable stiffness‑to‑reach ratio. The holder’s cutting height 38 mm and 32 mm body contribute to a low overhang and improved rigidity, while the 40 mm head width stabilises the insert under intermittent cuts. At approximately 1.421 kg, the mass helps dampen chatter on medium‑duty turning cycles, supporting higher feed rates and improved surface finish. These engineered dimensions enable efficiency gains on batch work, allowing faster cycle times without sacrificing component integrity. Compatibility and workshop integration for smooth setup Designed for common workshop standards, the tool holder fits WNMG 0804 grade inserts and references the clamping bar designation P08, simplifying part selection in tool inventories. The right‑hand orientation matches typical lathe setups where conventional forward turning is required, avoiding unnecessary holder swaps. For straightforward integration, the holder’s ISO designation and dimensional data allow quick verification against machine tool envelopes and turret pockets. Technical assistance for fixture selection and process adaptation is available through Metav Werkzeuge to ensure the holder performs optimally within the production cell. For Teknik Makina quality and dependable turning performance, contact Metav Werkzeuge in Emmerich for tailored advice and order processing: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: P152TM Manufacturer: Teknik Makina Article designation: PWLN for WNMG Indexable Inserts ISO designation: PWLNR 3232 Facts Overall length: 170 mm Cutting height: 38 mm Holder height: 32 mm Holder width: 32 mm Cutting head width: 40 mm Weight: 1.421 kg Cutting angle: 95° Special features Compatible with WNMG 0804 inserts Right‑hand orientation Clamping bar designation: P08 Tool category: turning tool holder for indexable inserts FAQ What insert size does the holder accept? The holder is specified for WNMG 0804 indexable inserts, ensuring a standard insert seat and reliable clamping. Is the orientation suitable for conventional turning on lathes? Yes, the component is a right‑hand turning tool holder designed for conventional lathe turning directions. What is the ISO designation for this tool holder? The ISO designation is PWLNR 3232, which aids compatibility checks with turrets and tool lists. How does the geometry affect machining stability? The combination of 170 mm overall length, controlled head width and body height reduces overhang and enhances rigidity, improving surface finish and reducing vibration. Which clamping bar or shank reference is compatible? The holder references the clamping bar designation P08, simplifying replacement and spares management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Klemmhalter 95° SCLCL 1010 J06 Für CC-- 0602 Wendeplatten Innenkühlung Linksschneidend - Teknik Makina
Taking advantage of a compact, ISO‑compliant design and robust clamping geometry results in consistent, repeatable turning operations; select this left‑hand toolholder for stable performance with CCMT inserts and order or consult Metav Werkzeuge for fast supply and expert guidance. Klemmhalter — SCLC holder for CCMT indexable inserts, left‑hand, SCLCL 1010 by Teknik Makina The Klemmhalter is a left‑hand clamping holder designed for turning with CCMT 0602 indexable inserts, suitable for standard lathe toolposts and ISO‑based tool selection. Left‑hand configuration for reverse turning ISO designation SCLCL 1010 Compatible with CC-- 0602 CCMT inserts 95° cutting angle for stable cutting Consistent clamping for repeatable turning results The holder offers precision clamping through a compact geometry that secures the insert with consistent bite and minimal play. With an overall length 110 mm, cutting height 10 mm and a head width 12 mm, the assembly is designed to fit common toolposts while keeping the cutting edge at the correct reference height. The ISO code SCLCL 1010 simplifies selection and inventory management by matching established toolholder conventions. Geometry tuned to reduce vibration and extend tool life A 95° cutting angle and rigid saddle contact reduce bending moments at the insert, which in turn lowers chatter and helps preserve the insert edge. The combination of short overhang and focused support delivers rigidity during interrupted cuts, translating into longer tool life and more predictable surface finish — advantages that improve productivity and reduce tool consumption in series production. Seamless integration and practical handling on the shop floor Marked for left‑hand machining and compatible with the CC-- 0602 size family, the holder accepts standard clamping screws and aligns with shank codes such as J06 for easier replacement and stocking. The lightweight construction (approx. 0.105 kg) and compact profile make indexable insert changes and tool rotations straightforward, helping to keep setup time low and machine uptime high. For procurement or technical specification requests for the Teknik Makina SCLC holder, contact Metav Werkzeuge for tailored advice and reliable delivery from Emmerich. Technical data Article number: D404TM Brand: Teknik Makina Designation: SCLC for CCMT Indexable Inserts (SCLCL 1010) ECLASS: 21181004 Cutting direction: left Dimensions & weight Cutting height: 10 mm Head width: 12 mm Holder width: 10 mm Overall length: 110 mm Weight: 0.105 kg Compatibility & features Compatible inserts: CC-- 0602 Cutting angle: 95° Shank/boring bar designation: J06 ISO designation: SCLCL 1010 FAQ Which inserts fit this holder? The holder is specified for CC-- 0602 / CCMT 0602 indexable inserts and is designed to secure that insert size with appropriate clamping geometry. Is the toolholder suitable for right‑hand turning? This version is a left‑hand configuration and is intended for reverse cutting directions; choose the corresponding right‑hand variant for standard right‑hand turning. What does SCLCL 1010 mean? SCLCL 1010 is the ISO designation indicating the holder shape and size family; it helps ensure correct selection and interchangeability with matching insert and shank standards. How compact is the holder for tight setups? With an overall length of 110 mm and a cutting height of 10 mm, the holder is compact and intended for confined toolpost arrangements where short overhang is required. Can this holder be used with standard clamping screws and toolposts? Yes; the holder follows common ISO conventions for insert seating and clamping, allowing use with standard clamping hardware and compatible toolposts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Precision coolant delivery for demanding turning operations
Tool holders with internal coolant are precision components used in machining, particularly turning, to hold indexable inserts securely and feed them to the workpiece. Also referred to as through-coolant tool holders or internal coolant toolholders, these systems channel coolant directly to the cutting edge to reduce thermal load and improve chip control in heavy or high-speed machining.
How they work and where they help most
Standard holders without internal coolant rely on external nozzles, which can be blocked by chips and fail to reach the insert tip reliably. In contrast, holders with internal coolant contain integrated coolant channels and boreholes in the tool shank that guide the coolant under pressure straight to the insert. This targeted supply is particularly valuable for difficult-to-machine materials, high cutting speeds, deep cuts and internal turning where conventional coolant delivery struggles.
Key facts
| characteristic | detail |
|---|---|
| category | tool holders with internal coolant |
| common synonyms | internal coolant toolholders; coolant-through tool holders |
| typical application | turning, heavy machining, internal bore finishing |
| coolant routing | internal channels and boreholes delivering coolant to the insert seat |
| key technical effect | direct cooling at the cutting edge, improved chip evacuation, reduced thermal load |
| comparison | standard holders use external nozzles; internal coolant holders route coolant through the shank |
Measurable benefits for production
- Direct coolant feed reduces the thermal stress on the insert, extending tool life.
- Improved pressure at the cutting zone enhances chip evacuation, reducing recutting and tool damage.
- More consistent cooling helps achieve better surface finish and dimensional stability.
- Reliable coolant delivery under challenging chip conditions supports higher cutting speeds and heavier cuts.
Metav: precision supply and industrial competence
Metav positions itself as the practical partner for workshops and production: a European quality filter based in Emmerich that combines broad product availability with technical expertise. With over 48,000 customers and more than 250,000 products, Metav supplies through-coolant tool holders and related accessories with dependable logistics and application guidance, making sophisticated cooling solutions accessible for every workshop.
In short
Tool holders with internal coolant deliver targeted, high-efficiency coolant to the insert tip, improving chip control, tool life and surface quality in demanding turning tasks.
FAQ
When should I choose tool holders with internal coolant over standard holders?
Choose tool holders with internal coolant when external coolant nozzles cannot reliably reach the cutting edge, for deep cuts, internal turning, heavy machining or when machining difficult materials at high speeds. The internal coolant toolholders ensure direct cooling and better chip evacuation in these scenarios.
Can internal coolant toolholders be used with all insert types?
Internal coolant toolholders are compatible with most indexable inserts provided the holder and insert interface are specified for coolant-through operation. Verify seat type and manufacturer recommendations for coolant-through compatibility.
What performance improvements can I expect from coolant-through tool holders?
Typical improvements include longer tool life, fewer interruptions from clogged external nozzles, improved chip control and a more consistent surface finish due to reduced thermal distortion at the cutting edge.
How is coolant delivered inside an internal coolant toolholder?
Coolant is channelled through boreholes and internal passages in the tool shank directly to the insert pocket; this focused path creates sufficient pressure at the cutting edge to flush chips away and cool the insert effectively.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com