Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
1.27mm Gauge Pin Length 50mm ±0.001mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of high repeatability and workshop-ready robustness provided by a compact 1.27 mm diameter and a tight ±0.001 mm tolerance together with a corrosion‑resistant special‑steel construction for dependable end‑measurements; order directly via Metav Werkzeuge or contact the consultants for application advice and stock status. Gauge pin M323.127 — single precision test pin, 1.27 mm, ±0.001 mm The Gauge pin M323.127 is a single, workshop‑grade test pin designed for precise end‑measurements and checking of small bores and features in inspection and production environments. Precision ±0.001 mm tolerance Diameter 1.27 mm, length 50 mm Made from special steel workshop grade Supplied in protective transport case Accuracy that supports repeatable inspection results The compact inspection pin delivers a ±0.001 mm manufacturing tolerance, which translates into reliable pass/fail decisions when used as a reference element in gauging jigs or manual checks. This level of precision places the pin in the realm of fine workshop metrology where micrometric reproducibility is required; deviations at this order are traced to material contact or fixture behaviour rather than the probe itself. The small 1.27 mm diameter and 50 mm length allow use in confined bores and assembly fixtures while maintaining stable seating and contact geometry. By specifying the tolerance in absolute terms, the component enables predictable interchangeability in serial quality checks and shortens corrective loops in production. Designed for practical workshop integration Built as a workshop execution, the test pin combines a hardwearing special‑steel body with a form factor that fits standard inspection racks and handheld fixtures. Handling is simplified by the balanced 50 mm length and a total mass of approximately 0.003 kg, which reduces inertia during manual transfer and positioning. Supplied in a protective transport case, the item is ready for safe storage and movement between bench, lab and machine shop without additional packaging steps. The robust construction minimises fretting and wear at contact points, so that maintenance intervals are extended and inspection throughput remains steady. Consistency, traceability and procurement convenience Traceability is supported by clear identifiers: SKU M323.127 and GTIN 4061905055218 allow inventory control and procurement integration. The special‑steel composition ensures dimensional stability under typical workshop conditions; hardened surfaces resist rapid abrasion, preserving the ±0.001 mm rating over repeated cycles. For purchasing and supply reliability, Metav IndustryLine places the emphasis on dependable stock and predictable lead times, backed by a European quality filter that vets incoming parts for conformity. This combination of dimensional accuracy, durable material selection and logistical transparency reduces downtime and contributes to consistent product quality. Contact Metav Werkzeuge in Emmerich for technical matching, availability and supply of the M323.127 gauge pin: info@metav-werkzeuge.com — Tel. +49 2822 7131930 Technical Data Article number: M323.127 GTIN: 4061905055218 Label: Prüfstift, einzeln, 1,27mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 1.27 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Workshop execution Protective transport case included Material: special steel SKU: M323.127 FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.127 is manufactured to a ±0.001 mm tolerance, enabling high‑precision end‑measurements and consistent repeatability in inspection tasks. Which dimensions define the pin for fixture planning? The pin has a diameter of 1.27 mm and a length of 50 mm, information that can be used directly for fixture layout and bore engagement calculations. Is the pin ready for workshop use on delivery? Yes, the M323.127 arrives as a workshop‑grade test pin and is supplied in a protective transport case suitable for safe storage and movement between bench, lab and shop floor. How is the product identified for ordering and stock control? Order and inventory references include SKU M323.127 and GTIN 4061905055218, which facilitate procurement and catalogue matching. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.28mm Gauge Pin Length 50mm ±0.001mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of micron-level accuracy (±0.001 mm) combined with a 1.28 mm diameter and a compact 50 mm length for dependable fit verification and repeatable checking in workshop environments; order the gauge pin directly via Metav Werkzeuge or ask our consultants for application support. Gauge pin M323.128 — Single workshop-grade gauge pin, 1.28 mm, ±0.001 mm The gauge pin M323.128 is a workshop-grade single gauge pin intended for precise end‑measurements and fit checks in inspection and assembly routines. Workshop-grade execution Tolerance ±0.001 mm for micron accuracy Compact 50 mm length for tight installations Manufactured from special steel for durability Micron accuracy where it matters The primary advantage of this gauge pin is its ±0.001 mm tolerance, which corresponds to one micrometre and allows reliable discrimination between barely differing fits. Such a fine tolerance makes the pin suitable for acceptance checks, go/no-go validations and serial inspection tasks where repeatability reduces rework and scrap. The high resolution supports quality control across production runs and provides a verifiable reference for measuring instruments or comparators. Robust construction for everyday workshop use Produced in special steel and specified as a workshop-grade component, the pin combines resistance to wear with practical handling characteristics. Its 50 mm length offers sufficient reach for many end‑measure and assembly checks while remaining short enough to avoid bending under normal handling. The light mass contributes to comfortable, safe handling during repetitive checks and reduces operator fatigue during batch verifications. Practical integration into inspection workflows Designed as a single pin for direct fit inspection, the component simplifies checks on bores, pins and assembly seats by offering a standardised reference gauge. The 1.28 mm diameter is useful for precision dowel checks and mating part verifications; its use streamlines decision-making in production and inspection stages by delivering quick, unambiguous results. When combined with documented measurement procedures, the pin helps sustain process stability and traceability across production cycles. Contact Metav Werkzeuge today for procurement and technical advice on Metav IndustryLine gauge pins — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M323.128 GTIN: 4061905055225 Brand: Metav IndustryLine Facts Diameter: 1.28 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: special steel Workshop-grade execution Single gauge pin for end measurements Intended for fit checks and inspection FAQ What tolerance does the gauge pin offer and what does that mean for inspections? The gauge pin M323.128 has a tolerance of ±0.001 mm, which allows micron‑level discrimination during acceptance checks and fit inspections, improving repeatability in serial measurements. Is the gauge pin suitable for use on precision dowel checks and small bores? Yes, the 1.28 mm diameter of the M323.128 makes it suitable for dowel verifications and small bore fit checks where tight dimensional control is required. What material is used and how does it affect durability? The pin is made from special steel, chosen for wear resistance and stability in workshop environments, which supports sustained accuracy over repeated use. Can the pin be used as a reference for serial inspection processes? The M323.128 gauge pin is designed for quick go/no‑go checks and standardised fit verification, making it a practical reference tool in serial inspection workflows. What is the intended application area for this pin? This single gauge pin is intended for end‑measurements, fit checks and assembly verification tasks in workshops and small‑batch production settings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.29mm Gauge Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
Take advantage of the extremely fine tolerance of ±0.001 mm, the compact 1.29 mm diameter and the 50 mm shaft to secure repeatable gauging and end‑measure inspections in a busy workshop environment. Order the test pin directly via Metav Werkzeuge or consult the team for integration advice. Test pin M323.129 — Inspection pin, 1.29 mm diameter, ±0.001 mm (Metav IndustryLine) The Test pin M323.129 is a workshop‑grade inspection pin designed for precise end‑measure checks, tight‑tolerance gauging and fixture‑based probing in mechanical workshops and quality control benches. Workshop-grade inspection pin Diameter 1.29 mm for fine gauges Tolerance ±0.001 mm for high accuracy Length 50 mm, special steel construction Consistent high precision for reproducible measurements The slender probe is engineered for repeatability in routine inspection tasks: with a stated tolerance of ±0.001 mm, the pin suits high‑precision checks where micrometre differences are critical. The small 1.29 mm diameter minimises contact area and is ideal for narrow bores, pin gauges and end‑measure references, while the 50 mm shaft length provides adequate reach without compromising stiffness. The special steel construction contributes to reliable surface behaviour under repeated contact, reducing measurement scatter and supporting consistent quality control results. Easy to integrate into fixtures and gauge systems The compact geometry and workshop specification make the pin straightforward to incorporate into bespoke fixtures, plug gauges and comparator setups. The 50 mm length is a practical compromise between reach and rigidity, enabling its use in modular test rigs and handheld comparators alike. Using a dedicated inspection pin of this calibre reduces rework and speeds up inspection cycles, a rational benefit for production lines and measuring stations that require fast, verifiable decisions. Robust handling and clear identification for workshop use Designed as a workshop version, the pin tolerates frequent handling and standard workshop conditions while maintaining dimensional stability. With a low mass of 0.003 kg and a clear manufacturer SKU for traceability, the component is easy to store, pick and deploy during batch inspections. The included GTIN aids inventory management and reduces sourcing errors; the clear specification and material declaration support procurement and long‑term replacement planning with minimal downtime. For reliable supply and technical guidance on the M323.129 inspection pin from Metav IndustryLine, contact Metav Werkzeuge in Emmerich — the team can advise on fixture compatibility and ordering options via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.129 GTIN: 4061905055645 Manufacturer: Metav IndustryLine EClass: 21170231 Data Diameter: 1.29 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: special steel Version: workshop execution Category: test pins FAQ What applications suit this inspection pin best? The M323.129 inspection pin by Metav IndustryLine is intended for end‑measure checks, gauge inserts and precise probing in mechanical workshops and quality control benches. Is the pin supplied with a calibration certificate? The M323.129 test pin is supplied as a workshop‑grade component; it is not delivered with a calibration certificate unless stated otherwise in the product label. Can this probe be used inside narrow bores and fixtures? Yes — the 1.29 mm diameter and 50 mm shaft length make the pin suitable for narrow bores and integration into bespoke fixtures or plug gauge assemblies. How is the component identified for reordering and inventory? Identification is via SKU M323.129 and GTIN 4061905055645, which support straightforward reordering and stock tracking for the inspection pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.2mm Test Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
The combination of a 1.20 mm diameter, ±0.001 mm tolerance and a robust 50 mm length ensures highly reproducible end‑measure checks in routine workshop use. Order the M323.120 directly via Metav Werkzeuge or consult our specialists for application advice. Test pin M323.120 — single precision gauging pin, 1.20 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Test pin M323.120 is a single, precision‑ground gauging pin designed for reliable end‑measure verification and workshop gauging tasks, combining fine dimensional control with a compact 50 mm form. Precision tolerance ±0.001 mm Diameter 1.20 mm, length 50 mm Special steel construction for durability Workshop version for routine gauging Repeatable precision for end‑measure verification The M323.120 serves where consistent dimensional checks are essential: its ±0.001 mm declared accuracy provides a clear quantitative basis for pass/fail decisions in small‑bore inspections and end‑measure controls. Because the pin is manufactured from special steel and finished for high concentricity, measuring uncertainty from the gauge itself is minimised, which helps to reduce rework and scrap rates. In practical terms, this means faster quality decisions during batch checks and more predictable outcomes for downstream processes. Durable construction and handling suited to busy workshops A compact 50 mm length combined with a 1.20 mm diameter yields a form factor that is easy to position while remaining stiff under normal gauging loads. The core material, listed as special steel, offers durability and wear resistance for repetitive insertion checks; the nominal mass of 0.003 kg reflects the small, machined geometry. The workshop specification emphasises a balance between handling robustness and measurement fidelity, so the pin is appropriate for regular use in fixture setups and comparative gauges without unnecessary fragility. Practical integration into quality routines and documentation Designed as a single, ready‑to‑use gauging element, this test pin fits directly into go/no‑go fixtures, measuring jigs and pin gauges for end‑measure tasks. The clearly stated dimensional data — 1.20 mm diameter, ±0.001 mm tolerance, 50 mm length — supports straightforward inclusion into inspection plans and measurement protocols. Metav IndustryLine’s positioning as a precision partner means the M323.120 is offered within a broader supply and documentation ecosystem that helps standardise workshop processes and maintain traceable component records. Contact Metav Werkzeuge to discuss how the M323.120 can be specified for existing fixtures or measurement procedures and to obtain the full product details Technical data Article number: M323.120 GTIN: 4061905054419 Brand: Metav IndustryLine Label: Test pin, single, 1.20 mm, ±0.001 mm, length 50 mm Special feature: Workshop version Core specifications Diameter: 1.20 mm Tolerance / accuracy: ±0.001 mm Length: 50 mm Weight: 0.003 kg Material: Special steel eCl@ss: 21170231 Design & functional features Single gauging pin (sold individually) Precision ground finish Suited for end‑measure checks and fixture use Compact, stiff geometry for reliable insertion FAQ What level of accuracy does the pin provide? The pin is specified with a tolerance of ±0.001 mm, making it suitable for very fine end‑measure verifications where micrometre‑level precision is required. What are the pin's exact dimensions? The gauging pin has a diameter of 1.20 mm and a length of 50 mm, matching the dimensional data for the M323.120. What material is used for the pin? The component is manufactured from special steel, selected for durability and stable dimensional behaviour in workshop environments. Is the pin supplied individually or as a set? This item is offered as a single gauging pin and is intended for installation in fixtures or use as a standalone check pin. How should the pin be handled to preserve accuracy? Handle by the shank without forcing sideways loads; store in a clean, dry environment to avoid contamination and prevent surface wear that could affect measurement fidelity. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.31mm Test Pin Single ±0.001mm Accuracy 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop durability, sub‑micron repeatability and compact handling for reliable end‑measure inspection. Order the test pin directly via Metav Werkzeuge or ask our consultants for application advice. M323.131 Test Pin — Single precision gauge pin 1.31 mm, ±0.001 mm (Metav IndustryLine) The M323.131 is a single test pin designed for precise end‑measure and gauge checks in workshop and inspection environments. Single test pin 1.31 mm diameter, high precision Tolerance ±0.001 mm for tight inspection tasks Length 50 mm suitable for through and blind checks Repeatable sub‑micron performance for critical inspections The component is manufactured for repeatable measurement where tight limits matter; the nominal diameter of 1.31 mm is held to a ±0.001 mm tolerance, ensuring that dimensional checks produce consistent, verifiable results. The tight tolerance makes the pin suitable for comparative gauging, pin‑and‑plug fit tests and end‑measure controls in small‑component production. Clear numerical stability reduces process variation and supports routine quality documentation. Workshop‑grade construction for robust handling Machined from special steel, the pin offers a balance between surface hardness and machinability that keeps wear low in repetitive use. At a length of 50 mm, the shank gives sufficient reach for through‑hole and blind‑depth checks while remaining easy to handle during repetitive inspection cycles. The workshop version specification prioritises practical durability and lowers the risk of deformation under typical handling conditions. Integrates simply into inspection routines and fixtures The compact form factor and precise diameter make the element straightforward to fit into standard test fixtures, gauge blocks and comparator setups. Marked as a workshop test item from Metav IndustryLine, the product (SKU M323.131) is intended for direct incorporation into established measurement sequences, supporting traceable checks and routine end‑of‑line verification. Packaging is provided for secure transport, easing storage and handling between production and quality control stations. For reliable gauge pins from Metav IndustryLine, order the M323.131 through Metav Werkzeuge in Emmerich or contact our advisors at info@metav-werkzeuge.com / +49 2822 7131930 for tailored application guidance Technical Data Article number: M323.131 GTIN: 4061905055669 Material: Special steel Diameter: 1.31 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Packaging: transport box Facts Category: Gauge pin / test pin Version: Workshop execution Use case: End‑measure and gauge checks SKU: M323.131 Special features High repeatability for small‑part inspection Compact, easy‑to‑mount geometry Delivered secured for transport and storage FAQ What tolerance can be expected from this test pin? The M323.131 test pin is specified with a tolerance of ±0.001 mm, allowing sub‑micron repeatability for tight inspection tasks. Which material is the pin made from and how does that affect wear? The pin is produced from special steel, chosen to balance hardness and wear resistance for prolonged workshop use. Is the length of 50 mm suitable for blind‑hole checks? Yes; the 50 mm length provides adequate reach for many blind‑hole and through‑hole verifications while remaining manageable in fixtures. Can the pin be used directly in gauge block comparisons and fixtures? The diameter and form factor of the M323.131 make it suitable for integration into standard fixtures and gauge block comparison setups. How is the product delivered and protected in transit? The item is supplied secured in a transport box to protect the pin during shipment and handling Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.32mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of high repeatability and ultraprecise tolerance control with a compact, workshop-grade measuring pin. Combining ±0.001 mm positional accuracy and a slender 1.32 mm diameter in a 50 mm length ensures reliable end‑measure checks and fast fixture verification—order the probe via Metav Werkzeuge or consult our specialists for application advice. M323.132 Test pin (single) — Ø 1.32 mm, ±0.001 mm, 50 mm — Metav IndustryLine The M323.132 is a single precision test pin designed for fine dimensional checks, end‑measure verification and fixture testing in workshop and toolroom environments. Workshop execution for everyday robustness Diameter 1.32 mm for fine detail checks Tolerance ±0.001 mm for sub‑micron repeatability Length 50 mm suited to fixture and gauge use Consistent precision for production control Manufactured from special steel, the measuring pin delivers a ±0.001 mm positional accuracy that supports high‑precision inspection tasks and reduces downstream rework. The slim 1.32 mm nominal diameter minimises intrusion into tight features while the 50 mm overall length provides enough reach for most gauge blocks, jigs and reference fixtures. In practice, this combination reduces readjustment cycles during set‑up and shortens control loops, meaning fewer stoppages and more predictable throughput. The compact mass also limits inertial effects during manual probe placement, preserving measurement repeatability. Practical benefits in workshop and toolroom use Built as a workshop version, the probe balances wear resistance with practical handling for routine checks and assembly control. The choice of special steel enhances surface stability under frequent use and resists minor impacts common at the bench. For technicians and quality engineers the pin functions effectively as a precision reference for end‑face checks or as a locating element in small fixtures; the geometry supports both axial alignment and repeatable contact position. Where fast comparative measurements are needed, the pin simplifies go/no‑go assessments and speeds up batch inspection. Integration and traceability for quality procedures Traceable identification and robust construction assist documentation within inspection plans and quality records. The pin’s nominal values and measured tolerance make it straightforward to reference in process control charts and inspection protocols. Lightweight construction minimises handling fatigue during repetitive checks and supports consistent touch force when used with mechanical holders. For customers requiring further data or compatibility information, Metav Werkzeuge offers technical consultation to align the probe with existing gauges or fixture systems, ensuring the test pin integrates cleanly into documented workflows. Order the Metav IndustryLine M323.132 test pin from Metav Werkzeuge for precision end‑measure verification and process reliability; for specification matching or application guidance contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.132 GTIN: 4061905055676 Material: Special steel Length: 50 mm Diameter: 1.32 mm Tolerance: ±0.001 mm Weight: 0.003 kg Facts Diameter: 1.32 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg GTIN: 4061905055676 Special features Workshop execution Single test pin Special steel construction SKU: M323.132 FAQ What inspection tasks is this test pin suited for? The M323.132 test pin from Metav IndustryLine is suited to end‑measure checks, fixture alignment and small‑feature verification where a 1.32 mm locating element and ±0.001 mm tolerance are required. Is the material corrosion resistant for workshop use? The measuring pin is made of special steel, selected for surface stability and wear resistance in a workshop environment; corrosion behaviour depends on local conditions and maintenance routines. Can the pin be used as a locating dowel in jigs? Yes, the probe functions reliably as a locating element in jigs and fixtures thanks to its precise diameter and stable length (50 mm), which support reproducible positioning and quick comparative checks. How is the M323.132 identified for inventory and traceability? Identification is via the SKU M323.132 and GTIN 4061905055676, enabling direct reference in inspection records and procurement systems. What benefits does the workshop execution provide? The workshop execution prioritises durability and practical handling for routine use, offering a balance between hardness and serviceability for frequent measuring tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.33mm Test Pin, Single, ±0.001 mm, 50mm Length, Workshop Version - Metav IndustryLine
Compact workshop test pin combining sub‑micron tolerance and robust special‑steel construction for consistent end‑gauge and inspection use; ideal where repeatable, small‑diameter checks are required. Order directly via Metav Werkzeuge or consult our specialists for technical alignment. Test pin M323.133 — precision 1.33 mm, ±0.001 mm | Metav IndustryLine A Test pin M323.133 engineered for workshop use, offering a 1.33 mm diameter and a length of 50 mm for precise end‑gauge and component inspection. Test pin M323.133 by Metav IndustryLine Diameter 1.33 mm with ±0.001 mm tolerance 50 mm length for end‑gauge tasks Made from special steel, workshop version Reduce rejects with measurable sub‑micron precision The M323.133 test pin delivers a tolerance of ±0.001 mm, a level of accuracy that significantly narrows the uncertainty band in go/no‑go and end‑gauge checks. Such fine specification is particularly effective when verifying bores, alignment pins or mating features where small deviations translate into assembly issues. By converting a dimensional check into a reproducible, numerical pass/fail result, this pin supports faster decision‑making on the shop floor and reduces downtime caused by unnecessary rework. The compact geometry and strict dimensional control make it suitable as a reference for comparative gauging and verification routines. Compact design for confined and precision applications A small diameter combined with a 50 mm usable length allows access to confined features without compromising handling or stability. The slim profile is useful when probing tight bores, locating tiny dowel seats or checking spacing in micro‑mechanical assemblies. The pin’s form factor balances reach and rigidity to minimise bending under light application forces, thereby improving measurement repeatability. For workshop environments that demand both dexterity and accuracy, this design eases handling while maintaining the geometric fidelity necessary for reliable inspections. Robust material choice for repeated workshop use Constructed from special steel, the test pin is intended for regular use in industrial settings where durability matters. The material selection provides resistance to wear and preserves the critical measuring diameter over many cycles, reducing the frequency of replacement and ensuring consistent results. For routine inspection tasks and production checks, the combination of a hardened contact surface and a corrosion‑resistant finish supports longevity and protects the calibrated condition of the gauge. Practical fit into quality assurance workflows Designed for straightforward integration into existing inspection routines, the pin serves as a compact reference element for incoming inspection, in‑process checks and final acceptance. Its clear numerical specification and robust construction enable the transfer of measurement tasks from specialised labs to the workshop while keeping traceability and repeatability intact. When used alongside standard gauging jigs or comparators, the pin gives a fast, objective check that complements digital measurement systems and manual comparators alike. Contact Metav Werkzeuge to check compatibility of the M323.133 test pin with existing gauging setups or to request delivery from our Emmerich quality hub: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.133 GTIN: 4061905055683 Brand: Metav IndustryLine Category: Measuring pins Facts Diameter: 1.33 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: Special steel Workshop execution Suitable for end‑gauge and inspection tasks ECLASS: 21170231 FAQ What applications is this test pin suitable for? The M323.133 test pin from Metav IndustryLine is suitable for end‑gauge checks, bore verification and small‑feature inspections where a 1.33 mm reference is required. How precise is the measurement capability of the pin? The test pin offers a tolerance of ±0.001 mm, providing sub‑micron repeatability for fine inspection tasks with consistent pass/fail assessment. Which material is used and why does it matter? Manufactured from special steel, the pin resists wear under repeated use and preserves the critical diameter for reliable inspection cycles. Can the pin be used in a production environment? Yes — the workshop design of this Metav IndustryLine test pin makes it robust for regular shop‑floor inspections and integration with gauging fixtures. What is the article number for ordering or referencing? Refer to the article number M323.133 and GTIN 4061905055683 when ordering or specifying the test pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.34mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied In Case - Metav IndustryLine
Compact precision and robust workshop design combine here to ensure repeatable end‑measure checks: the 1.34 mm diameter with a tight ±0.001 mm tolerance and a 50 mm shaft minimise measurement variance and speed up pass/fail decisions. Order this gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.134 — precision gauge pin, 1.34 mm, ±0.001 mm (Metav IndustryLine) A precision gauge pin intended for reliable end‑measure and limit checks in workshop environments, presented as a single, hardened measuring pin. Workshop-grade construction for robust daily use Diameter 1.34 mm with ±0.001 mm tolerance 50 mm length for deep-feature checks Special steel for wear resistance Faster inspection through measurable precision A narrow tolerance reduces uncertainty and accelerates routine checks: the ±0.001 mm specification allows this pin to serve as a dependable reference for go/no‑go assessments and dimensional verification. Because the diameter is set at 1.34 mm, insertion fits and seating behaviour are highly reproducible; deviations that matter for production control are immediately apparent. This degree of precision supports a reduction in rework by enabling clear, objective pass‑fail decisions and shorter inspection loops. Built to last in daily workshop use Constructed in a workshop-grade format and machined from special steel, the shaft offers resistance to abrasion and deformation under repeated seating. The 50 mm overall length balances access to recessed features with a stiffness that limits bending during measurement, which preserves dimensional integrity over time. Where frequent handling and repeated insertions are expected, the combination of material choice and compact geometry delivers lower lifecycle costs through extended service intervals. Simple integration into common metrology tasks Designed as a single probe for end measurement, the gauge pin M323.134 is suitable as a calibrated reference in inspection benches and jigs, or as a quick‑check tool in first article inspection. The compact form factor supports compatibility with a wide range of fixtures and extension tools, while the clear numeric specification ensures traceability in documentation. With its defined tolerance and standard dimensions, the pin can be incorporated into routine quality control procedures to improve repeatability and simplify reporting. Contact Metav Werkzeuge today to discuss Metav IndustryLine gauge pins or to request technical matching for specific inspection tasks; deliveries are managed from our Emmerich location for reliable supply across Europe. Technical data Article number: M323.134 GTIN: 4061905056383 Manufacturer: Metav IndustryLine Facts Diameter: 1.34 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Accuracy class: ±0.001 Special features Workshop execution Material: special steel Single measuring pin for end‑measure applications Category: gauge pin (messstifte) Story trigger: end‑measure FAQ What is the diameter tolerance of the gauge pin? The gauge pin M323.134 is manufactured to a ±0.001 mm diameter tolerance for high‑precision reference measurements. Which material is used for the shaft? The shaft is made from special steel, chosen to provide durability and resistance against wear during repeated use. For which applications is this pin intended? It is intended for end‑measure checks, go/no‑go reference tasks and quick dimensional verification in workshop inspection routines. How is traceability provided for this pin? The product is listed with GTIN 4061905056383 and is supplied with the documented nominal and tolerance values for inclusion in inspection records. What length is available and why is it useful? A 50 mm length offers sufficient reach for recessed features while maintaining stiffness to reduce measurement error. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.35mm Gauge Pin, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine ±0.001 mm tolerance, a compact 1.35 mm diameter and a 50 mm working length for repeatable end‑measurement checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Pin M323.135 – 1.35 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The gauge pin M323.135 is a single‑piece precision test pin designed for fine inspection tasks and end‑measurement verification in workshop environments High precision tolerance ±0.001 mm Diameter 1.35 mm for fine inspection 50 mm working length Workshop‑grade special steel construction Accuracy that reduces inspection uncertainty The core benefit of this pin is its ±0.001 mm specification, which supports repeatable dimensional checks in quality control processes. With a nominal diameter of 1.35 mm, the pin is suited to narrow bores and tight fits where micrometre‑level certainty matters. The narrow tolerance reduces ambiguity in go/no‑go assessments and enables faster decision making on the shop floor, lowering rework rates and improving first‑pass yield. Robust, workshop‑ready construction for everyday use Built as a workshop version, the pin combines compact geometry with resilient special steel for reliable handling in routine inspection tasks. The 50 mm length gives a useful reach without sacrificing stiffness, keeping deflection minimal during insertion. Lightweight at 0.003 kg, the component is easy to position in jigs and fixtures while offering the mechanical integrity required for repeated contact in busy production runs. Designed for precise end‑measurement verification Intended for end‑measurement applications, this test pin acts as a reference probe for gauging assemblies, fixture alignment and comparative checks. Supplied as a single item, the component integrates with standard inspection setups and can serve as a replacement pin in sets or bespoke gauges. The simple geometry means measurement uncertainty is governed by diameter tolerance and handling technique, so consistent test procedures maximise the benefit of the specified accuracy. Traceability, identification and procurement made straightforward Identification via GTIN 4061905056390 and SKU M323.135 ensures straightforward inventory control and traceability through procurement and inspection records. The compact dimensions and workshop focus make this pin a practical choice where space, speed and precision intersect—for example, detailed end‑of‑line checks, sample testing or integration into maintenance toolkits. Reliability in delivery is underpinned by Metav IndustryLine’s quality filter at the Emmerich site. Contact Metav Werkzeuge today for tailored advice or to request the Metav IndustryLine gauge pin M323.135 for reliable end‑measurement verification — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M323.135 GTIN: 4061905056390 Description: Test pin, single item, 1.35 mm, ±0.001 mm, 50 mm length Facts Diameter: 1.35 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Accuracy: ±0.001 Special features Material: Special steel Workshop execution Application: end‑measurement Item type: Gauge pin Category: Gauge pins FAQ How precise is the gauge pin? The gauge pin M323.135 has a tolerance of ±0.001 mm, providing micrometre‑level precision suitable for tight tolerance inspections in workshop and inspection settings. What material is used for this test pin? The M323.135 is manufactured from special steel chosen for wear resistance and dimensional stability under typical workshop conditions. For which applications is this pin most suitable? This test pin is intended for end‑measurement verification, narrow bore checks and use in jigs or fixture assemblies where a small‑diameter, high‑precision reference is required. Is the item supplied individually or in a set? The product is supplied as a single gauge pin (single item) and is suitable as a spare or for integration into bespoke inspection tools. How is the product identified for procurement and traceability? Identification is provided via GTIN 4061905056390 and SKU M323.135 to support purchasing, inventory and inspection traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.36mm Gauge Pin ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of exact roundness and repeatable length control combined with workshop-ready durability for consistent go/no-go checks in serial production. Benefit from the ultra-fine ±0.001 mm tolerance and the compact 1.36 mm diameter to ensure precise end‑measurements; order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application advice. M323.136 Gauge pin (single) — 1.36 mm, ±0.001 mm, 50 mm length — Metav IndustryLine The M323.136 gauge pin is a single test pin designed for precision end‑measurement and fit checking in workshop and inspection environments Workshop version for robust handling Diameter 1.36 mm for precise fits Tolerance ±0.001 mm high accuracy Length 50 mm for deep measurements Accuracy that reduces rework and speeds inspection A ±0.001 mm tolerance delivers measurable benefits for quality control and final inspection: fewer false rejects and faster acceptance decisions. The very small 1.36 mm diameter and calibrated length provide a reliable reference for plug and bore checks, while the tight roundness and dimensional stability support automated and manual gauging routines. This level of precision is particularly useful where tight fits and clearance checks determine assembly success, allowing process engineers to quantify tolerances rather than estimate them. Built for everyday workshop use with dependable material properties Manufactured from special steel, the pin balances surface hardness and resistance to wear with ease of handling. The workshop execution emphasises robustness for repeated insertion and removal in jigs, fixtures and test benches. A 50 mm overall length gives sufficient reach for deeper bores and stepped components while remaining compact enough for handheld inspection. The combination of material choice and construction reduces deformation risk during routine use, supporting reproducible results across shifts. Clear identification and traceability for production lines Items are supplied with the visible product code M323.136 and manufacturer identification to simplify storekeeping and traceability. The included GTIN 4061905056406 supports inventory workflows and ensures correct part selection for assembly or inspection stations. Stable labelling and a compact form factor reduce picking errors and speed up tool changes on the shop floor, which in turn shortens process downtime and improves throughput. Practical application: where this test pin adds value The single gauge pin is suitable for final inspection, quick gauge blocks checks, sliding‑fit verification and small‑bore roundness spot checks. Its high precision makes it suitable for both prototype evaluation and low‑volume production where dimensional certainty is required. When incorporated into a routine inspection sequence, the pin helps standardise go/no‑go checks and supports consistent documentation of acceptance criteria. For precision applications that demand reproducible sub-micron control, contact Metav Werkzeuge regarding the Metav IndustryLine M323.136 gauge pin to discuss suitability for specific fixtures and to arrange supply from Emmerich — info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: M323.136 GTIN: 4061905056406 Label: Prüfstift, einzeln, 1,36mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 1.36 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: Special steel Workshop version Supplied in protective transport case FAQ Is the gauge pin suitable for serial go/no-go checking? The M323.136 gauge pin from Metav IndustryLine is designed for serial go/no-go and fit verification tasks thanks to its ±0.001 mm tolerance and stable length. What materials is the pin compatible with for inspection tasks? The gauge pin itself is constructed from special steel and is used as a reference artefact; appropriate handling prevents damage when used with soft or abrasive workpieces. How is the M323.136 delivered and identified for stock control? The product is supplied with clear labelling and GTIN 4061905056406 to support inventory systems and avoid mix-ups on the shop floor. Can this pin be used for deep bore checks? With a 50 mm length, the pin is intended for deeper bore access than standard short pins and suits many fixtures that require extended reach. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.37mm Gauge Pin ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
This workshop-grade gauge pin combines sub-micron repeatability, a compact 1.37 mm diameter and ±0.001 mm tolerance with a robust 50 mm length for reliable end‑measure checks; supplied in a protective transport case and produced from special steel. Order directly via Metav Werkzeuge or contact our consultants for application advice and availability. Gauge pin M323.137 — Workshop test pin, 1.37 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The gauge pin M323.137 is a single, workshop‑grade test pin intended for precise end‑measure verification and small‑bore checking in routine metrology and inspection tasks. Workshop version for daily shop use Diameter 1.37 mm with ±0.001 mm tolerance Length 50 mm for end‑measure checks Delivered in protective transport case Repeatable, measurable accuracy for everyday inspection A compact test pin with a 1.37 mm diameter and ±0.001 mm tolerance provides a measurable basis for repeatable fit and end‑measure assessments. The tight tolerance reduces uncertainty in pass/fail checks and helps to prevent costly rework by ensuring immediate detection of deviations. Manufactured in a workshop execution, this pin is intended for frequent handling and fast inspection cycles; the special steel construction supports dimensional stability during routine use. Designed for tough shop environments and safe handling The workshop design emphasises robustness without compromising precision. At 50 mm length and a low mass of 0.003 kg, the pin is easy to position and manoeuvre in restricted setups, while the protective transport case minimises the risk of nicks and contamination during storage and transport. The compact format suits bench inspection procedures and keeps handling straightforward in both manual and semi‑automated verification stations. Simple integration into inspection processes and traceability As a single gauge pin, the item is suitable for end‑measure verification, fixture set‑up and small‑bore checks within larger gauging routines. Clear identifiers such as GTIN and SKU permit simple inventory management and traceability for quality records. The precise dimensions make the pin suitable as a workshop reference component for routine checks and quick comparative measurements, supporting a consistent quality workflow. Request supply or technical advice from Metav Werkzeuge—contact Metav Werkzeuge GmbH in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical details Article number: M323.137 GTIN: 4061905056413 Manufacturer: Metav IndustryLine SKU: M323.137 Core specifications Diameter: 1.37 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.003 kg Classification: Workshop execution Features / Materials Material: Special steel Application: End‑measure verification / small‑bore checks Delivery: Protective transport case ECLASS: 21170231 FAQ What tolerance does the pin offer? The gauge pin M323.137 is specified with a tolerance of ±0.001 mm, providing high repeatability for workshop verification. Which material is used for this test pin? The pin is made from special steel, selected for dimensional stability and suitability for routine shop handling. Is the pin delivered ready for use and protected? Yes, the item is supplied in a protective transport case to reduce the risk of damage during storage and transport. What inspection tasks is this pin suited to? This single test pin is intended for end‑measure verification, small‑bore checks and quick fixture set‑ups in workshop inspection routines. How can the pin be identified for inventory and traceability? Identification is via GTIN 4061905056413 and article number M323.137 for clear traceability in quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.38mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Finish, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of highly repeatable inspection results through a combination of extreme dimensional accuracy, compact form and durable special steel construction; the result is fewer rejects and faster inspection cycles. Order the M323.138 gauge pin directly via Metav Werkzeuge or consult our team for specification matching. M323.138 gauge pin — 1.38 mm, ±0.001 mm (Metav IndustryLine) A M323.138 gauge pin designed for precision end-measure checks and fine-fit verification in metrology and workshop inspection environments High-precision tolerance ±0.001 mm Diameter 1.38 mm for fine fits Length 50 mm for deeper checks Special steel workshop version Reliable precision for fine-fitting measurements This compact inspection element delivers micrometric accuracy where small clearances matter. With a declared tolerance of ±0.001 mm, the pin reduces uncertainty in go/no-go and fit verification tasks, allowing consistent decisions during quality control. The small 1.38 mm diameter is optimised for narrow bores and precision holes; the slim profile helps to access confined features without influencing the assembly or mating surfaces, which improves overall repeatability of checks. Durable construction that supports frequent use Manufactured from special steel and offered in a workshop grade configuration, the gauge pin balances surface integrity with day-to-day robustness. The 50 mm length provides enough engagement for many inspection scenarios while remaining easy to handle and less prone to bending than overly long probes. These material and geometric choices mean lower wear over repeated cycles and a longer interval between replacements, supporting efficient inspection routines and steady production throughput. Practical fit for inspection workflows Supplied as a single element for individual use in inspection benches or pin sets, the pin suits both manual and fixture-based checks. The 50 mm shank allows safe handling and deeper insertion into housings and recesses without needing special adapters. Traceability is supported by the SKU and GTIN on product documentation; identification and inventory management in central stores or quality labs is straightforward, making integration into existing inspection kits seamless. Choose the Metav IndustryLine M323.138 gauge pin for repeatable fine-fit control and request delivery from Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M323.138 GTIN: 4061905056420 SKU: M323.138 Brand: Metav IndustryLine Facts Diameter: 1.38 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: special steel Supply form: single gauge pin Workshop execution FAQ What is the declared tolerance of this gauge pin? The M323.138 gauge pin is specified with a dimensional tolerance of ±0.001 mm, suitable for fine-fit verifications. For which inspection tasks is this pin suitable? This gauge pin from Metav IndustryLine is intended for precise end-measure checks, narrow-bore diameter verification and fine-fit assessments in workshop and metrology environments. How is the product supplied and identified? The item is delivered as a single gauge pin; identification is available via SKU M323.138 and GTIN 4061905056420 for inventory and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.39mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of ±0.001 mm tolerance and durable special steel in a compact 50 mm length for repeatable inspection results; order the M323.139 directly via Metav Werkzeuge or consult the technical team for application support. Gauge pin M323.139 (single) – 1.39 mm, ±0.001 mm, 50 mm length by Metav IndustryLine The Gauge pin M323.139 is a workshop‑grade precision test pin designed for dimensional verification and end‑position checks in routine inspection and assembly environments. Workshop‑grade construction Diameter 1.39 mm, tolerance ±0.001 mm 50 mm hardened special steel shaft Supplied in protective case Consistent precision for routine inspection This single gauge pin delivers a repeatable measurement with a stated accuracy of ±0.001 mm, making it suitable for fine tolerance checks and verification tasks where small deviations matter. The tight tolerance reduces uncertainty in go/no‑go checks and fits verification, enabling faster decision‑making on production lines and in quality control benches. As a hardened inspection pin, it provides a stable reference for plug measurements and helps maintain traceable results across repeated cycles. Built to endure workshop conditions Manufactured in special steel and presented in a workshop‑grade execution, the tool withstands regular handling while retaining dimensional stability. The 50 mm shaft length and slender 1.39 mm diameter are optimised for confined bore inspections and plug checks in assemblies. Supplied in a protective case, the pin is protected during transport and storage, reducing the risk of nicks that would compromise measurement integrity. The compact, single‑piece design supports straightforward use in fixtures and manual inspection rigs. Practical use and integration into inspection routines Ideal for bench checks, fixture set‑ups and final inspection, the pin functions as a straightforward reference for bore gauging and pass/fail assessments. The compact geometry and high-precision specification simplify integration with existing inspection jigs and optical comparators; the gauge pin can be used where a precise cylindrical reference is required. Traceability is supported by the supplied labelling and the product’s unique SKU, which aids inventory control and process documentation in quality management systems. For reliable workshop inspections choose the Metav IndustryLine M323.139 gauge pin and contact Metav Werkzeuge in Emmerich for technical advice and prompt delivery to your facility: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: M323.139 GTIN: 4061905056437 Label: Prüfstift, einzeln, 1,39mm, +/- 0.001 mm Länge 50 mm Category: Messstifte Facts Diameter: 1.39 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: special steel Workshop version Supplied in protective case Single piece gauge pin FAQ What is the intended use of this gauge pin? The M323.139 gauge pin is intended for precision plug checks, bore verification and end‑position inspection in workshop and production environments. How tight is the tolerance and what does it mean for inspections? With a tolerance of ±0.001 mm the gauge pin offers very fine repeatability; this level of accuracy supports precise go/no‑go assessments and reduces uncertainty in pass/fail decisions. Is the pin supplied ready for use and protected for transport? The gauge pin is supplied as a single, workshop‑grade item and comes in a protective case to prevent damage during transport and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.3mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
The combination of high repeatability, ultra‑fine ±0.001 mm tolerance and a compact 50 mm length ensures dependable end‑measurements; order the gauge pin directly via Metav Werkzeuge or contact our advisers for application support. M323.130 Gauge pin, 1.30 mm diameter, ±0.001 mm tolerance — Metav IndustryLine A M323.130 gauge pin designed for precision end‑measurements, inspection gauges and jig alignment in workshop and production settings. Workshop‑grade construction Diameter 1.30 mm, tolerance ±0.001 mm Length 50 mm for deeper features Made from special steel, hardened finish Precision where small differences decide outcomes This inspection pin delivers high precision for end‑measurement tasks thanks to its tight ±0.001 mm tolerance and nominal 1.30 mm diameter. For applications in quality control and gauge setting, this degree of accuracy reduces measurement uncertainty and rejects fewer parts at final inspection. The compact geometry supports repeatable contact conditions, which is essential when consistency across multiple measurement points is required. Robust design for everyday workshop use Manufactured in a workshop‑grade execution, the pin combines a 50 mm shank length with a surface finish that resists ordinary wear. The balanced length-to‑diameter ratio keeps the pin stable during insertion and avoids excessive bending in typical jigs and fixtures. As a result, throughput improves because fewer rechecks are necessary and fitting operations remain reliable during routine production. Streamlining inspection and tooling workflows As a single test pin for end‑measurements, this component integrates easily into existing gauge blocks, masters and fixture plates. The gauge pin format simplifies replacement and calibration tasks, reducing downtime in maintenance cycles. Where traceable repeatability is part of the inspection plan, using a dedicated pin of known tolerance minimises operator variation and shortens the time needed to validate a measurement setup. Material selection and service life considerations Made from special steel with a hardened finish, the pin is tailored for long service life under regular contact stresses in jigs and inspection tools. The choice of material supports dimensional stability and resistance to surface damage that would otherwise affect measurement reliability. For environments requiring documented calibration history, specify calibration options through Metav Werkzeuge to maintain quality records. Contact Metav Werkzeuge today to discuss Metav IndustryLine gauge pins and arrange supply or technical advice — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.130 GTIN: 4061905055652 Manufacturer: Metav IndustryLine Facts Diameter: 1.30 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Measurement range: 1.3 mm Special features Material: Special steel Workshop execution Single test pin for end‑measurements Suitable for inspection, jigging and calibration FAQ What applications is this gauge pin suitable for? The M323.130 gauge pin is suitable for end‑measurements, fixture alignment and inspection gauge setups in production and workshop environments. How tight is the tolerance and what does it mean for measurement reliability? With a tolerance of ±0.001 mm, the M323.130 provides very fine repeatability, reducing measurement uncertainty in critical end‑measurement tasks. What material is used and how does it affect durability? The pin is made from special steel with a hardened finish; this material combination improves wear resistance and maintains dimensional stability over repeated use. Can this pin be used as a replacement in existing gauge sets? Yes. The single test pin format and standard diameter make the M323.130 compatible with common gauge holders and fixture designs for easy replacement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.41mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
The combination of exceptional dimensional accuracy, robust special-steel construction and workshop-ready packaging ensures reliable in-process checks and repeatable go/no-go assessments; order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application advice. Gauge pin M323.141 — Metav IndustryLine, diameter 1.41 mm, tolerance ±0.001 mm Gauge pin M323.141 is a single, hardened test pin for precise end-diameter checks in workshop and inspection environments Diameter 1.41 mm with ±0.001 mm tolerance 50 mm length, workshop version Special steel construction for durability Supplied individually in transport box Precise measurement for reliable production decisions This workshop-grade gauge pin delivers a tight ±0.001 mm tolerance on a 1.41 mm diameter, enabling decisive go/no-go assessments where small deviations matter. The fine tolerance reduces measurement uncertainty and supports faster acceptance or rejection of parts during batch inspections. By converting numerical accuracy into clear pass/fail results, the instrument shortens inspection cycles and lowers scrap rates, making it especially valuable in serial production and quality-control stations. Built for the workshop — toughness and handling Crafted from special steel and finished for everyday use, the pin’s 50 mm length balances reach with stiffness for repeated insertions and removals. The workshop version construction emphasises resistance to wear and deformation under typical shop handling. Supplied individually in a transport box, the item remains protected between uses and during transit, which preserves the calibrated geometry and extends service life while simplifying storage and organisation at the workbench. Practical applications and compatibility with inspection workflows As an end-measure reference, this pin is suitable for verifying drilled holes, bores and fixture openings where a precise reference diameter is required. The compact single-pin format suits manual gauges, fixture checks and bench-top inspection routines. When used alongside other plug or ring gauges, the device helps establish a clear measurement chain, improving reproducibility across operators and machines and reducing rework caused by ambiguous inspection outcomes. Confidence through traceable identification and Metav quality The part is identified as M323.141 and carries the GTIN 4061905057168 for traceability within procurement and inventory systems. Supplied under the Metav IndustryLine umbrella, the item benefits from Metav’s quality filtering and logistics from Emmerich, which supports consistent availability and dependable handling. The combination of traceable identification and robust construction promotes auditability and long-term consistency in routine inspection tasks. For workshop checks that require sub-micrometre certainty, request the Metav IndustryLine gauge pin M323.141 from Metav Werkzeuge — Metav’s specialists can advise on integration into existing inspection routines and supply matching reference sets Technical data Article number: M323.141 GTIN: 4061905057168 Material: Special steel Diameter: 1.41 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Category: Gauge pins / Messstifte Brand: Metav IndustryLine Workshop design Supplied in transport box Facts Diameter (numerical): 1.41 mm Tolerance (numerical): ±0.001 mm Length (numerical): 50 mm Weight (numerical): 0.003 kg Special features Single-piece delivery Robust finish for shop use GTIN for traceability Workshop execution designation FAQ What is the intended use of this gauge pin? The gauge pin M323.141 from Metav IndustryLine is intended for end-diameter checks, verification of drilled holes and go/no-go assessments in workshop and inspection environments. Is the diameter specification suitable for precision inspection work? Yes, the 1.41 mm diameter with a ±0.001 mm tolerance makes this pin suitable for precise dimensional checks and reliable pass/fail decisions in standard production control. How is the product supplied and protected in transit? The pin is supplied individually and protected in a transport box to preserve the measuring geometry and ensure safe handling between uses. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.42mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Compact, workshop-grade precision with a guaranteed micro tolerance and robust stainless-feel finish: the combination of ±0.001 mm tolerance, 1.42 mm nominal diameter and a 50 mm length ensures reliable end‑measurement checks in serial inspection and setup tasks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.142 by Metav IndustryLine — 1.42 mm diameter, ±0.001 mm tolerance The Gauge pin M323.142 is a single test pin designed for precise end‑measurement tasks and reference fitting in workshop and inspection environments. Tolerance ±0.001 mm Diameter 1.42 mm Length 50 mm Special‑steel construction Precision where it counts for repeatable inspection results The gauge pin delivers a manufacturable micro tolerance of ±0.001 mm, which translates directly into measurable improvements in first‑off verification and in‑process spot checks. Such a fine tolerance reduces uncertainty when establishing reference fits or checking end dimensions, enabling higher confidence in pass/fail decisions. Thanks to the compact 1.42 mm diameter and the slim 50 mm shaft, the component is especially suited to small bores, dowel seats and dimensional references where space is limited but repeatability is crucial. Workshop durability and handling that supports busy production Made from special steel, this workshop‑grade pin resists wear during repeated seating and extraction, preserving the critical diameter tolerance over time. The modest mass and straight shank geometry simplify handling during assembly and inspection, while the 50 mm length provides reach for recessed features without sacrificing stiffness. Built as a single test pin for quick interchange in pin sets or fixture pockets, the component combines low handling effort with robust metrological properties to keep throughput steady. Integrating the pin into quality control workflows Traceability and procurement are straightforward: the part is available under SKU M323.142 with GTIN for order and inventory management. Use the pin as a reference in gauging fixtures, as a go/no‑go seating reference, or as a datum when setting up small assemblies; its geometry makes it compatible with standard pin guides and hardened locating bores. The compact form factor supports tight tolerances in serial production and helps reduce rework by improving the clarity of inspection tolerances at the operator level. Metav IndustryLine's catalogue position ensures consistent availability for routine replacement and set replenishment. For application guidance or to secure workshop‑grade M323.142 pins from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for fast procurement and technical advice: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.142 GTIN: 4061905057502 Manufacturer: Metav IndustryLine Facts Nominal diameter: 1.42 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg eClass: 21170231 Special features Material: special steel Workshop execution Story trigger: end measurements FAQ What is the achievable measurement tolerance with this gauge pin? The gauge pin offers a tolerance of ±0.001 mm, making it suitable for micro‑precision end‑measurements and reference seating. Is the pin suitable for use in small bore gauging and dowel checks? Yes, the 1.42 mm diameter and 50 mm length make the test pin ideal for small bore inspection, dowel seat checks and tight‑fit references. Which material is the gauge pin made from and what does that mean for wear resistance? The pin is manufactured from special steel, selected to balance hardness and resistance to wear under frequent seating and extraction in workshop conditions. How is the product identified for ordering and inventory? Order using SKU M323.142 or GTIN 4061905057502; the part is listed under Metav IndustryLine for consistent procurement. Can the pin be used as a datum in fixture set‑ups? Yes, the pin’s straight shank and precision tolerance make it suitable as a datum or reference for fixture alignment and small‑part assembly checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.43mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Finish - Metav IndustryLine
Take advantage of the combination of micro‑tolerance accuracy, compact design and robust special steel construction for reliable reference measurements and stable fixture alignment; order the item directly via Metav Werkzeuge or request specialist advice from our consultants. Test pin M323.143 — Single gauge pin, 1.43 mm diameter, ±0.001 mm accuracy The Test pin M323.143 is a single, high-precision gauge pin intended for end-measure checking and reference probing in workshop metrology applications. ±0.001 mm tolerance for reference measurements 1.43 mm diameter for fine bore verification 50 mm length for deep-pocket access Workshop version with robust special steel construction Consistent, repeatable reference measurements The core advantage of this gauge pin is its ±0.001 mm tolerance, which delivers consistent reference values for assembly jigs, go/no-go checks and micro‑inspection tasks. With such a fine tolerance the pin serves as a reliable master for dimensional verification, reducing measurement scatter and rework. The compact diameter and calibrated length make it suitable for small bores and precision fit checks where a stable datum is required. Durable construction for everyday workshop use Manufactured from special steel, the pin combines contact durability with dimensional stability under normal workshop conditions. The 50 mm shaft provides sufficient engagement for many fixture designs while remaining manageable for handling and storage. The workshop specification ensures the part resists wear from repeated contact, maintaining the 1.43 mm reference dimension through routine use in production and quality assurance processes. Integration into inspection and tooling workflows As a single precision gauge pin, this component is straightforward to integrate into existing gaging sets, plug gauges or fixture assemblies. The small form factor supports access into tight bores and cavities, simplifying pass/fail checks and alignment operations. Used as a reference dowel in inspection sequences, the pin helps to reduce cycle time and improve throughput by providing an immediate, traceable measurement point. For precise reference measurements choose the Metav IndustryLine Test pin M323.143; contact Metav Werkzeuge in Emmerich for ordering and technical guidance at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.143 GTIN: 4061905057519 Brand: Metav IndustryLine Facts Diameter: 1.43 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Workshop version Single gauge pin for end-measure applications Material: special steel FAQ What is the dimensional tolerance of this gauge pin? The Test pin M323.143 features a tolerance of ±0.001 mm, suitable for high‑precision reference measurements. Which materials is the pin made from? This item is produced from special steel, selected for contact durability and dimensional stability in workshop environments. For which applications is the gauge pin intended? The gauge pin is intended for end‑measure checks, fixture alignment and fine bore verification where a compact, high‑accuracy reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.44mm Gauge Pin, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm repeatability, a compact 1.44 mm diameter and a robust 50 mm length to streamline precision checks in production and inspection. The workshop‑grade construction and protective transport case keep the gauge pin ready for daily use. Order this gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Metav IndustryLine Gauge Pin — 1.44 mm, ±0.001 mm tolerance The Metav IndustryLine gauge pin 1.44 mm is a workshop‑grade precision cylindrical gauge designed for fast end‑measurement and fit verification in inspection, assembly and toolrooms. High‑precision ±0.001 mm tolerance Diameter 1.44 mm for tight fits 50 mm overall length for handling convenience Special‑steel construction with transport case Reduce inspection time with measurable accuracy A compact cylindrical gauge that delivers ±0.001 mm nominal tolerance improves process control by limiting uncertainty at the smallest scales. As a plain‑language equivalent: the diameter variation is better than one thousandth of a millimetre, which is sufficient for most precision fits, go/no‑go checks and press‑fit verifications. Using such a high‑accuracy pin reduces the number of secondary checks and helps avoid rework, because the measurement outcome is directly comparable and repeatable under workshop conditions. Built for repeatable handling and long‑term use The pin is made from special steel and finished for workshop applications, giving a balance between wear resistance and dimensional stability. The 50 mm shaft provides enough length for secure gripping while keeping the gauge compact for toolboxes and bench use. Supplied as a workshop‑grade item, the component benefits from familiar handling characteristics: it seats easily in jigs, enters tight bores without wobble and resists distortion during routine use. Practical application and inspection advice This cylindrical gauge is primarily intended for quick verification of hole diameters, locating pins and fitted components where a nominal 1.44 mm size is required. For accurate results, measure with gentle seating and avoid lateral forces; if repeatable traceability is required, integrate the pin into a routine that logs measurement outcomes. The protective transport case included with delivery safeguards the pin from knocks and contamination between uses, preserving its dimensional integrity over time. Choose the Metav IndustryLine gauge pin for dependable micro‑inspection and contact Metav Werkzeuge for supply and tailored advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M323.144 GTIN: 4061905057526 Manufacturer: Metav IndustryLine Facts Diameter: 1.44 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Workshop‑grade execution Material: Special steel Supplied in protective transport case Single item supply (individual gauge pin) FAQ What is this gauge pin used for? This gauge pin is used for end‑measurement and fit checks of small bores and locating holes; the Metav IndustryLine gauge pin 1.44 mm is suited to quick inspection tasks in workshops and assembly stations. How precise is the diameter of the pin? The nominal diameter is 1.44 mm with a tolerance of ±0.001 mm, which permits reliable go/no‑go assessments and dimensional checks at micrometre scale. What material is the pin made from and how durable is it? The pin is manufactured from special steel in a workshop‑grade finish, offering good wear resistance for regular inspection use while maintaining dimensional stability. Is the pin delivered with protective packaging? Yes—the gauge pin is supplied in a protective transport case to prevent damage during storage and transit. Which article number should be ordered? Order using SKU M323.144 (GTIN 4061905057526) to ensure the correct gauge pin is supplied. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.45mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of workshop-grade accuracy combined with a compact 1.45 mm diameter and a durable special steel construction for reproducible end‑measure checks. Order the pin directly via Metav Werkzeuge or consult our specialists for application-specific guidance. Gauge pin M323.145 — single precision test pin, 1.45 mm diameter, ±0.001 mm (Metav IndustryLine) The gauge pin M323.145 is a single, high-precision test pin designed for fine end‑measure verification and fit checks in workshop inspection routines. Workshop-grade precision pin ±0.001 mm Diameter 1.45 mm, length 50 mm Made from special steel for durability Supplied in a protective transport case Reliable accuracy for critical fits The pin delivers a declared tolerance of ±0.001 mm, making it suitable where close dimensional control is essential. This level of precision supports repeatable checks of bores, plugs and mating parts in small‑feature components and helps to identify infinitesimal deviations that would otherwise affect assembly quality. The compact 1.45 mm diameter is particularly useful for narrow holes and precision gauges, providing a stable reference for go/no‑go assessments and end‑measurement tasks. The precise geometry reduces measurement uncertainty and improves consistency in routine quality control. Durable design for everyday workshop use Constructed from special steel, the pin combines wear resistance with dimensional stability under normal handling. The 50 mm nominal length offers convenient handling and reach for most small to medium test tasks while remaining easy to store and position in fixtures. As a workshop version, it withstands frequent use and is supplied in a protective transport case, which preserves the measuring surface during storage and transport. These characteristics reduce the need for frequent replacement and support a dependable inspection flow on the shop floor. Smooth integration into inspection workflows The pin is supplied as a single item with clear identification (SKU and GTIN) for traceable inventory management and straightforward procurement. Its compact form factor and clear specification simplify the selection process for calibration, fixture mounting or insertion into inspection jigs. For bespoke metrology setups or repeated comparative checks, the pin acts as a stable datum that complements calipers and micrometres in quality control stations. The straightforward specification enables rapid comparison against technical drawings and measurement logs. For precise, repeatable end‑measure verification choose the Metav IndustryLine gauge pin M323.145 — contact Metav Werkzeuge for tailored advice and procurement at info@metav-werkzeuge.com or +49 2822 7131930. Technical data SKU: M323.145 GTIN: 4061905054587 Manufacturer: Metav IndustryLine Description: single gauge pin, 1.45 mm, ±0.001 mm, length 50 mm Facts Diameter: 1.45 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: special steel Workshop version Supplied in a protective transport case Category: Gauge pins FAQ What tolerance does the pin offer? The declared tolerance of the gauge pin is ±0.001 mm, providing high‑precision control for fine fits. Is the pin suitable for measuring small bore diameters? Yes, the 1.45 mm diameter and stable geometry make the pin suitable for checking narrow bores and precision fit examinations. What material is the pin made from? The pin is manufactured from special steel, designed for durability and dimensional stability in workshop use. Is the pin supplied with a protective case? Yes, the item is supplied in a protective transport case to preserve the measuring surface during storage and handling. Can the pin be supplied calibrated? Calibration is not specified in the product data; for calibration options and certificates, please contact Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.46mm Test Pin ±0.001mm Length 50mm Workshop Version Plastic Case - Metav IndustryLine
Benefit from the combination of ultra-fine tolerance (±0.001 mm) and workshop-grade construction for dependable end-measure inspections. Order the gauge pin M323.146 directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.146 — 1.46 mm diameter, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) A gauge pin M323.146 designed for exact end-measure checks and precision locating tasks in workshop environments Ultra-fine tolerance ±0,001 mm 1.46 mm diameter, 50 mm length Workshop-grade special steel construction Supplied in a protective transport case Consistent results for tight tolerances This precision pin delivers repeatable measurement accuracy thanks to its ±0.001 mm specification. For production processes where small deviations lead to rework, the fine tolerance reduces uncertainty and supports consistent quality control. The compact geometry and stable material properties make the component suitable for series inspections and dimensional verification where reliable end-measure and plug checks are required. Durable workshop design that eases handling Manufactured in special steel and labelled as a workshop edition, the pin withstands everyday handling and the demands of a metalworking environment. The 50 mm length provides secure engagement in fixtures and test benches while the slender 1.46 mm diameter allows access to narrow bores and pockets. Supplied in a protective transport case, the item is ready for safe storage and routine use on the shop floor. Clear application logic and measurement benefit Engineered for end-measure checks, the pin acts as a precise reference probe for gauging and locating operations. Its geometry minimises bending and ensures stable contact during measurement cycles, which lowers measurement scatter and supports faster inspection throughput. Where interchangeability and traceable checks are required, this pin integrates into established inspection routines with minimal setup time. For procurement or advice on integrating Metav IndustryLine gauge pins into production workflows, contact Metav Werkzeuge for local supply and technical guidance. Technical data Article number: M323.146 GTIN: 4061905054594 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 1,46mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 1.46 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.003 kg Special features Material: special steel Workshop version Supplied in a protective transport case eClass: 21170231 Story trigger: end measures (endmasse) FAQ What level of accuracy does this gauge pin provide? The gauge pin M323.146 offers an accuracy of ±0.001 mm, intended for fine inspection and precise end-measure checks. Is the pin suitable for use in a production workshop? Yes, the workshop-grade construction and special steel make the pin appropriate for regular use on the shop floor. Does the item arrive ready for storage and transport? The pin is supplied in a protective transport case to facilitate safe handling and storage. Which measurements is the pin primarily used for? The pin is designed for end-measure and locating tasks, particularly for small bores, plug checks and fixture alignment. Can the pin be used as a reference in inspection fixtures? Yes, the dimensional stability and fine tolerance of this gauge pin make it suitable as a reference element in inspection fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.47mm Test Pin Single, ±0.001mm, Length 50mm, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high‑precision tolerance, workshop-grade construction and stable probing length for reliable end‑gauge and dimensional inspections. Order genuine Metav IndustryLine test pins directly via Metav Werkzeuge or consult the specialists for application advice. Test pin M323.147 — single gauge pin, 1.47 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A Test pin M323.147 designed for precise end‑gauge checks and dimensional control in workshop and inspection routines. Workshop-grade special steel construction Diameter 1.47 mm with ±0.001 mm tolerance Length 50 mm for stable probing Supplied individually for flexible use Precision that reduces measurement uncertainty The pin offers an ultra‑tight tolerance of ±0.001 mm, equivalent to 1 µm, which significantly reduces measurement uncertainty when used for end‑gauge or reference checks. Such a specification places the component in the realm of high‑precision inspection tools, suitable for fine quality control tasks where reproducibility matters. The 1.47 mm diameter is manufactured to exacting limits so that fits, clearances and calibrated plug gauges can be verified reliably. Explaining the benefit: a smaller stated tolerance means fewer rejected parts due to measurement error and a clearer signal when process adjustments are required. Workshop design for repeatable handling and durability Constructed from special steel and supplied as a single unit, this test pin combines corrosion resistance with a form factor optimised for handheld and fixture use. The 50 mm length provides a stable bearing surface during probing, which helps maintain repeatability across multiple measurements and operators. The workshop specification emphasises robustness under everyday use: components are finished to avoid burrs and ensure smooth seating in gauge holders. As a consequence, downtime for handling‑related issues is minimised and calibration intervals remain predictable. Practical integration into inspection workflows The product is intended for straightforward incorporation into existing inspection jigs, plug gauges and comparator setups; traceable inspection routines benefit from the pin’s consistent geometry. When recorded as a reference element in quality documentation, the ±0.001 mm tolerance supports tighter process capability assessments and clearer go/no‑go decisions. For shops aiming to raise inspection confidence without complex retrofits, this single test pin can serve as a compact, dependable reference in measuring benches or mobile inspection kits. For custom fixturing or batch supplies, Metav IndustryLine options and support can be consulted. Secure workshop accuracy with Metav IndustryLine precision pins — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for specification guidance and reliable supply. Technical data Article number: M323.147 GTIN: 4061905054600 Label: Prüfstift, einzeln, 1,47mm, +/- 0.001 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 1.47 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: Special steel Workshop version Single delivery unit Application: end‑gauge and dimensional inspection FAQ What level of accuracy can be expected from this test pin? The test pin delivers an accuracy of ±0.001 mm (1 µm); this allows clear differentiation of small dimensional deviations during end‑gauge and plug‑gauge checks. Is the pin suitable for use in standard gauge holders and fixtures? Yes. The pin’s geometry and 50 mm length are compatible with common inspection jigs and comparator setups used in workshop environments. What material is used and how does it affect durability? Manufactured from special steel, the pin is designed for daily workshop use with a focus on wear resistance and stable seating, which supports repeatable measurements. Can this item be used as a reference in quality documentation? Yes. With a defined tolerance of ±0.001 mm, the component is appropriate as a reference element for documented inspection routines and process capability checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.48mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of submicrometre accuracy, robust special steel construction and a compact 50 mm length for consistent end‑dimension checks in the workshop; order the part directly from Metav Werkzeuge or contact the consultants for specification advice. M323.148 Gauge Pin (Metav IndustryLine) — 1.48 mm, ±0.001 mm The M323.148 is a workshop‑grade gauge pin designed for precise end‑dimension inspection and fixture alignment in metalworking and quality control applications. Diameter 1.48 mm with ±0.001 mm tolerance 50 mm working length for compact components Special steel, workshop execution for durability Supplied in a transport case for safe handling Reliable checks with measurable tolerance and repeatability The inspection pin offers a diameter of 1.48 mm with a tolerance of ±0.001 mm, making it suitable for demanding go/no‑go and end‑dimension verifications where repeatability is essential. The tight tolerance reduces ambiguity in acceptance criteria and helps shorten inspection cycles, which supports efficient production throughput. The compact design yields rapid handling during batch checks and fixture set‑up, enabling objective pass/fail decisions without elaborate measurement routines. Designed for workshop conditions and long service life Constructed from special steel and specified as a workshop execution, the pin resists wear under routine use and maintains dimensional stability over extended inspection runs. The moderate 50 mm length provides sufficient contact area while remaining easy to manipulate in confined assemblies or jigs. The robust finish ensures reliable seating in bores and repeatable alignment, so fewer re‑measurements are needed—contributing to lower rework rates and steadier process capability. Practical integration into inspection and assembly workflows Supplied in a protective transport case, the component is immediately ready for use at the bench or in the calibration lab and remains organised between shifts. The small mass and compact footprint make it suitable for portable inspection kits and fixture‑setting tasks. Where traceability is required, the clear labelling and the manufacturer‑grade SKU facilitate inventory control and replacement planning, supporting quality management processes without unnecessary complexity. For specification guidance, batch availability or to order the Metav IndustryLine M323.148 gauge pin with assured delivery from Emmerich, contact Metav Werkzeuge for expert assistance and fast dispatch. Technical data Article number: M323.148 GTIN: 4061905054617 Brand: Metav IndustryLine Numbers Diameter: 1.48 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: Special steel Workshop execution Delivery: Transport case included Label: Prüfstift, einzeln, 1,48mm, +/- 0.001 mm Länge 50 mm FAQ What is the nominal diameter and tolerance of the pin? The pin has a nominal diameter of 1.48 mm and a declared tolerance of ±0.001 mm (SKU M323.148), suitable for high‑precision end‑dimension checks. Is the pin suitable for fixture alignment and go/no‑go testing? Yes, the compact 50 mm length and tight tolerance make the pin well suited to fixture alignment and rapid go/no‑go inspections in workshop environments. What material is used and how does it affect durability? The pin is manufactured from special steel in a workshop execution, which provides enhanced wear resistance and dimensional stability for routine inspection tasks. How is the product delivered and stored between uses? The gauge pin is supplied in a transport case to protect the measuring surface and to simplify storage and handling between shifts. Can the product be tracked or reordered using a unique identifier? Yes, the part is identifiable by SKU M323.148 and GTIN 4061905054617 for inventory control and straightforward reordering. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.49mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of workshop-grade robustness and micrometre-level accuracy for reproducible end‑measure checks; this single gauge pin combines a Ø 1.49 mm diameter with ±0.001 mm tolerance and a 50 mm length for consistent inspection results. Order directly via Metav Werkzeuge or contact the consultants for application advice and stock information. Gauge pin M323.149 — Single test pin, Ø 1.49 mm, ±0.001 mm, 50 mm A gauge pin M323.149 designed for precise end‑measure inspections and workshop checking of small components. High accuracy ±0.001 mm Compact Ø 1.49 mm diameter Robust workshop edition Delivered in transport case Precision that supports repeatable quality control The instrument's ±0.001 mm specification offers micrometre‑class repeatability, making it suitable for tight tolerance checks during final inspection or when setting up gauges and fixtures. The small Ø 1.49 mm working diameter allows access to narrow bores and fine features, while the 50 mm length provides reach without compromising stability. This combination reduces measurement uncertainty and helps maintain process control across batch runs, translating directly into fewer rejections and less rework. Durable design for the workshop environment Built as a workshop edition, the pin is manufactured from special steel for wear resistance under frequent handling. The compact mass and balanced geometry minimise bending moments during insertion, maintaining dimensional integrity over repeated cycles. Delivery in a dedicated transport case ensures safe storage and portability between inspection stations or job sites, preserving the gauge surface and supporting reliable use in everyday production routines. Practical integration into inspection workflows The single test pin is intended for end‑measure and go/no‑go checks where a clear, unambiguous result is required. Its straightforward form factor facilitates quick deployment within existing jigs and comparison sets; traceable identification (GTIN included in technical data) simplifies inventory management and quality documentation. For workshop teams seeking a low‑effort component that delivers high precision, this test pin is an efficient addition to control plans and first‑article inspections. For dependable, ready‑to‑use measuring components choose Metav IndustryLine’s gauge pin M323.149 — contact Metav Werkzeuge for availability, delivery options and specialist advice. Technical Data Article number: M323.149 GTIN: 4061905054624 Manufacturer: Metav IndustryLine Category: Gauge pins / Test pins Numeric data Diameter: 1.49 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.003 kg EClass: 21170231 Features & application Workshop edition Material: Special steel Delivered in transport case Suitable for end‑measure checks and small bores Story trigger: endmasse FAQ Is this pin supplied individually or in sets? The gauge pin is supplied as a single test pin; the product is listed as a single item under the designation M323.149 from Metav IndustryLine. Can the pin be used for bore gauging and end‑measure checks? Yes, the Ø 1.49 mm diameter and 50 mm length make the pin suitable for bore gauging and end‑measure inspections where micrometre accuracy is required. What material is used and how does it affect durability? The test pin is made from special steel, chosen for wear resistance in workshop conditions to ensure sustained dimensional reliability during frequent use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.4mm Gauge Pin Length 50mm ±0.001 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm repeatability, a compact 1.40 mm diameter and a 50 mm working length for reliable end‑measurement in workshop inspections. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin, single, 1.40 mm, ±0.001 mm, length 50 mm (Metav IndustryLine) Test pin, single, 1.40 mm, ±0.001 mm, length 50 mm is a precision inspection pin designed for fine end‑measurement tasks and everyday workshop use Workshop version for robust everyday use Diameter 1.40 mm with ±0.001 mm tolerance Length 50 mm for confined inspection tasks Made from special steel for wear resistance Accuracy designed for traceable inspection results The compact inspection pin delivers a tolerance of ±0.001 mm, which translates into reproducible end‑measurements where small deviations matter. Thanks to the fine diameter and tightly controlled geometry, this precision component supports consistent compliance checks on small bores, seats and mating faces. The high level of dimensional control reduces uncertainty in quality reports and simplifies pass/fail decisions during serial inspection, making it a rational choice where measurement certainty is priority. Robust workshop configuration for daily routines Built as a workshop version, the pin balances dimensional exactness with mechanical resilience. The use of special steel increases resistance to surface wear and handling marks that commonly occur in production environments. The 50 mm length is practical for access into assemblies without sacrificing stiffness, while the compact 1.40 mm profile suits confined features and thin walls. These characteristics combine to support efficient throughput and lower rework rates in routine inspection workflows. Integration into metrology workflows and traceability As a small-format gauge element, the component integrates readily into handheld and bench inspection sequences, complementing dial test indicators, height gauges and gauge blocks. The pin's consistent geometry aids in repeatable seating and alignment during comparative checks and gauging templates. Where process documentation is required, the component provides a clear, measurable reference value that supports quality records and audit trails in production and workshop environments. For reliable workshop inspections with high repeatability, request the Metav IndustryLine test pin (M323.140) from Metav Werkzeuge — experts are available at info@metav-werkzeuge.com or +49 2822 7131930 to advise on suitable inspection setups Technical data Article number: M323.140 GTIN: 4061905056444 Brand: Metav IndustryLine Facts Diameter: 1.40 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.003 kg Special features Material: special steel Configuration: workshop version Application: end‑measurement Category: test pins FAQ What is the main application of this inspection pin? The inspection pin M323.140 is intended for precise end‑measurement tasks such as checking small bores, seats and mating faces in workshop and production inspections. How tight is the dimensional tolerance of the pin? This Metav IndustryLine test pin is specified with a tolerance of ±0.001 mm, providing high repeatability for comparative gauging and critical fit checks. Which materials is the pin suitable for measuring against? The pin itself is made from special steel and functions as a reference element; contact surfaces measured are application dependent, while the pin resists common workshop wear. Can the pin be used in confined or hard‑to‑reach features? Yes, the compact 1.40 mm diameter and 50 mm length make the pin suitable for confined inspection tasks where accessibility is limited. Is this component suitable for routine workshop use? The workshop configuration and durable special steel construction make the M323.140 fitting for daily inspection routines and repeated handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com