High-precision clamping holders with internal coolant for extended tool life
Clamping holders with internal coolant are designed to secure indexable inserts accurately while delivering coolant directly to the cutting edge, reducing thermal load and improving chip evacuation in demanding metalworking operations. Used for turning and internal machining of tough materials, these holders channel the coolant through built-in boreholes to the insert and beneath the chip, which boosts tool life and enhances surface finish. As a reliable system solution, the combination of clamping holder, internal coolant and indexable insert ensures consistent performance at high cutting speeds and under heavy cut conditions.
12mm SDJC For DCMT Indexable Inserts 93° SDJCR 1212 J11-F For DCMT 11T3 Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a compact, robust clamping solution that combines precise insert positioning and space-saving dimensions for reliable external turning operations; order directly via Metav Werkzeuge or request tailored advice from the consultants. Clamping holder SDJC for DCMT indexable inserts — right-hand, flat style by Teknik Makina The SDJC for DCMT Indexable Inserts is a right-hand clamping holder designed for external turning with a flat head, optimised for DCMT 11T3 inserts in confined setups. Right-hand clamping holder SDJCR 1212 Flat head for DCMT 11T3 indexable inserts 12 × 12 mm head dimensions for compact turning 110 mm overall length, lightweight 0.134 kg Stable cutting performance for small-diameter turning The holder, designated SDJCR 1212, secures DCMT 11T3 indexable inserts in a low-profile mounting that reduces tool overhang and vibration. The flat head geometry, together with a defined 93° cutting angle, was engineered to maintain a repeatable cutting edge position, which is beneficial when machining short, external profiles. Precision is supported by the standardised ISO-style seat, so insert seating and indexing are consistent; this reduces set-up deviations and contributes to predictable tool life and part tolerances. Space-saving design that improves machining access With a head footprint of 12 mm by 12 mm and an overall length of 110 mm, the turning holder enables access in tight fixtures and close to shoulders where larger tools would obstruct the operation. The holder’s lightweight construction (0.134 kg) reduces dynamic loads on the turret during rapid direction changes, which helps to preserve surface finish. The right-hand orientation is matched to clockwise cutting applications and is suitable for many general-purpose turning tasks in job shops and production cells where compactness and rigidity are required. Compatibility and practical workshop advantages The unit accepts indexable inserts, permitting economical regrinds and rapid replacement without full tool change. The bar designation J11-F indicates the compatible shank system for insertion into common tool posts and turrets. As a standardised clamping solution, the component is compatible with established insert grades and chipbreaker geometries, allowing adaptation to a wide range of materials and cutting conditions while keeping inventory management straightforward. Reliability, supply and partner assurance Manufactured by Teknik Makina and distributed through Metav’s quality-controlled supply chain, the toolholder combines practical design with consistent availability for workshop planners. The standardised ISO-style identification and compact dimensions mean predictable integration into existing tooling setups, reducing planning time and improving machine uptime. For machining strategies where small turnings, close tolerances and repeatable insert location matter, this holder delivers measurable process stability. Contact Metav Werkzeuge for specification matching and delivery from Emmerich — telephone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for tailored advice and rapid dispatch. Technical Data Article number: D457TM Manufacturer: Teknik Makina Product: SDJC for DCMT Indexable Inserts SKU: D457TM ISO designation: SDJCR 1212 Compatible insert: DCMT 11T3 Cut direction: right eClass: 21181004 Facts Head width: 12 mm Head height: 12 mm Head cutting width: 12 mm Overall length: 110 mm Weight: 0.134 kg Cutting angle: 93° Special features Flat head design Right-hand clamping holder Bar designation J11-F Indexable insert compatibility Compact, low-profile construction FAQ What inserts fit this clamping holder? The clamping holder is specified for DCMT 11T3 indexable inserts and secures them via the SDJCR 1212 seat for standard seating and indexing. Is the holder right- or left-hand oriented? This toolholder is a right-hand design, intended for clockwise cutting directions in standard turning operations. What are the key dimensions to check for turret fitment? Critical dimensions are the 12 mm head width/height and 110 mm overall length; verify turret clearance and the J11-F bar designation for correct shank compatibility. Will the holder work in tight shoulder machining? Yes — the flat head and compact 12 × 12 mm footprint are intended to improve access in confined setups while maintaining a stable cutting position. Which manufacturer produces this toolholder and who supplies it? The toolholder is produced by Teknik Makina and supplied via Metav’s distribution, referenced under SKU D457TM for procurement and stock enquiries. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SDJCL 1212 SDJC For DCMT 11T3 Indexable Inserts, For DCMT 11T3 Inserts, Innenkühlung, Linksschneidend, 93° - Teknik Makina
Take advantage of a compact, left‑hand clamping solution with internal coolant and proven compatibility with DCMT 11T3 indexable inserts for steady turning performance; purchase directly from Metav Werkzeuge or request specialist advice from our consultants. SDJC Clamping Holder for DCMT Indexable Inserts — Left‑hand holder with internal coolant (Teknik Makina) The SDJC for DCMT Indexable Inserts is a left‑hand clamping holder designed for turning operations that require internal coolant delivery and a compact 12 mm shank for versatile workshop use Holder SDJCL 1212 by Teknik Makina Internal coolant for reliable chip evacuation Compatible with DCMT 11T3 indexable inserts Left‑hand orientation, 93° cutting angle Precision clamping for reproducible turning results The holder is engineered to deliver consistent clamping pressure via its SDJCL 1212 ISO profile, which secures DCMT‑style inserts with repeatable seating. This reduces setup time and minimises rework by keeping the insert position stable across cycles. The compact 12 mm shank and 16 mm cutting head width balance rigidity and access, so turning tasks that demand tight tolerances benefit from reduced vibration and improved surface finish. Coolant‑assisted chip control that supports productivity Equipped with internal coolant, the tool directs coolant to the cutting zone so chips are cleared efficiently and tool life is extended. For materials that produce long or stringy chips, forced coolant can prevent martensitic heat build‑up and lessen manual cleaning intervals. The internal feed is integrated without compromising the holder profile, meaning coolant is supplied while retaining full clamping reliability. Designed for workshop compatibility and quick changeovers Compatibility with DCMT 11T3 indexable inserts and the J11‑IC toolholder designation ensures that the holder fits common insert geometries and available insert grades. The left‑hand orientation and 93° cutting angle are suited to specific turning set‑ups, while the supplied Torx and clamping hardware (M3.5x11 Torx screw, T15 key, and M5 clamping plate screw) are industry standard for rapid, secure insert changes. At 110 mm overall length and 0.11 kg weight, the holder is easy to handle during tool changes and storage. Built for reliable, everyday workshop use Materials and construction are focused on longevity and consistent performance; the holder is finished to withstand routine use and is compatible with a range of insert grades for diverse materials. The robust clamping mechanism, together with measured dimensions and a 32 mm cutting height, supports repeatable setups and predictable machining results, so production planners can schedule operations with confidence rather than frequent adjustments. For reliable turning with internal coolant and DCMT compatibility, contact Metav Werkzeuge for availability and technical guidance — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: AP514TM Manufacturer: Teknik Makina ISO designation: SDJCL 1212 For indexable inserts: DCMT 11T3 Toolholder designation: J11-IC Weight: 0.11 kg Overall length: 110 mm Total height: 12 mm Shank width: 12 mm Cutting head width: 16 mm Cutting height: 32 mm Cutting angle: 93° Internal coolant: yes Cutting direction: left U‑plate: TA030 U‑plate screw: M5 Torx screw: M3,5x11 Torx key: T15 SKU: AP514TM FAQ What insert types are compatible with this holder? The holder accepts DCMT 11T3 indexable inserts; the SDJC geometry is matched to that insert form for reliable seating and repeatability. Is the coolant internal or external on this clamping holder? Internal coolant is provided; coolant is channelled to the cutting zone to aid chip evacuation and tool life. What is the ISO designation and main dimensions of the holder? The ISO designation is SDJCL 1212, with a 12 mm shank width, 110 mm overall length and a 16 mm cutting head width. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SDJCR 1212 SDJC for DCMT Indexable Inserts for DCMT 0702, Innenkühlung, Rechtsschneidend, 93° - Teknik Makina
Take advantage of the compact 12 x 12 mm shank, internal coolant, and compatibility with DCMT 0702 inserts to improve chip control and repeatability in small to medium turning operations. Order the tool via Metav Werkzeuge or contact the technical team for application advice. SDJCR 1212 clamp holder — right‑hand turning holder with internal coolant (Teknik Makina) The SDJCR 1212 clamp holder is a right‑hand turning toolholder designed for indexable DCMT 0702 inserts, offering internal coolant and a compact 12 x 12 mm shank for stable turning in confined setups. Right‑hand turning holder SDJCR 1212 Internal coolant for improved chip control Compatible with DCMT 0702 indexable inserts Compact 12 x 12 mm shank for small setups Improved cycle time through secure clamping and coolant supply The SDJCR 1212 is built for consistent production cycles by combining a robust clamping system with integrated coolant supply. The internal coolant channel directs cutting fluid close to the cutting edge, which reduces thermal load and improves chip evacuation; this leads to longer insert life and fewer interruptions for tool changes. With a lightweight construction of 0.17 kg and a 125 mm overall length, the holder balances rigidity and manoeuvrability, making it suitable for batch production and shorter set‑ups where fast throughput and reliable repeatability matter. Precision and compatibility for predictable turning results Configured for DCMT 0702 indexable inserts, the holder ensures consistent geometry and repeatable cutting conditions. The 93° cutting angle and 27 mm cutting height are engineered to maintain clearance and minimise interference in typical lathe operations. The part’s 12 x 12 mm shank and 16 mm cutting head width support accurate positioning in small turrets and tool posts, while the supplied M2.5×5.5 Torx screw (driven with a T8 key) secures the insert reliably, reducing micro‑movement under load. These features translate into stable surface finishes and predictable tool life in turning tasks. Practical workshop advantages and maintenance ease Assembly and maintenance are straightforward: the standard Torx fixation simplifies insert changes and ensures repeatable clamping torque, while the compact geometry reduces the need for special adapters. The holder’s compatibility with the common K07‑IC boring bar designation expands its integration options in modular setups. Because the design focuses on core performance—secure clamping, coolant delivery and dimensional compatibility—it supports both experienced setups and users seeking dependable results with minimal tuning. For dependable turning performance, request the Teknik Cutting Tools SDJCR 1212 clamp holder via Metav Werkzeuge or call +49 2822 7131930 / email info@metav-werkzeuge.com for tailored application advice Technical Data Article number: AP560TM Manufacturer: Teknik Makina ISO designation: SDJCR 1212 ECLASS: 21181004 Facts Shank width: 12 mm Shank height: 12 mm Cutting head width: 16 mm Cutting height: 27 mm Overall length: 125 mm Weight: 0.17 kg Cutting angle: 93° Special features Internal coolant Compatible with DCMT 0702 inserts Right‑hand cutting direction Torx screw: M2.5×5.5 Torx key: T8 Boring bar designation: K07‑IC FAQ Which inserts fit this holder? The holder is designed for DCMT 0702 indexable inserts, providing correct seating and repeatable geometry for standard turning tasks. Does the holder support internal coolant? Yes, this SDJCR 1212 clamp holder features internal coolant to direct fluid to the cutting zone and assist chip control. Is the clamping screw a standard size? The clamp is secured with an M2.5×5.5 Torx screw, tightened using a T8 key, ensuring straightforward insert changes and secure fixation. What is the intended cutting direction? The toolholder is configured for right‑hand turning operations and is optimised for that feed orientation. Can the holder be used in compact turrets? With a 12 x 12 mm shank and 125 mm overall length, the holder is suitable for compact turrets and limited‑space tool posts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SVJBL 1212 SVJB Holder for VBMT 1103 Indexable Inserts, Internal Cooling, Left-Hand Cutting, 93° - Teknik Makina
Take advantage of the holder's combination of rigid clamping, internal coolant and compact 12×12 mm head to secure stable left-hand turning operations; purchase through Metav Werkzeuge or request tailored advice from our consultants. Klemmhalter SVJB for VBMT Indexable Inserts — left-hand, internal coolant (Teknik Makina) Klemmhalter SVJB for VBMT Indexable Inserts is a left-hand turning toolholder engineered for secure clamping of VBMT 1103 indexable inserts and for coolant-fed machining in constrained toolpost setups. For VBMT 1103 indexable inserts Internal coolant supply to the insert Left-hand orientation, 93° approach angle Compact 12×12 mm head for tight spaces Greater machining stability through compact, rigid design The Klemmhalter SVJB is designed to deliver consistent tool support where rigidity matters. The compact 12×12 mm head and a nominal overall length of 110 mm reduce overhang and vibration, helping to improve surface finish and tool life in short‑to‑medium reach turning. The holder’s SVJBL 1212 ISO designation signals a standardised geometry that simplifies fixture planning and replacement in production environments. Built for industrial workshops, the clamping geometry and mass distribution focus on minimising chatter during interrupted cuts while keeping changeover straightforward. Cooler cutting, longer tool life An integrated internal coolant channel supplies cutting fluid directly to the insert seat, improving chip evacuation and temperature control at the cutting edge. Used with VBMT 1103 inserts this coolant feed reduces thermal wear and supports higher material removal rates on moderate to demanding applications. The holder’s 93° cutting angle combined with left-hand cutting orientation is particularly effective for facing and certain profiling tasks, where coolant-directed lubrication helps preserve edge integrity and extend insert life. Practical handling and workshop compatibility Changeover and maintenance are simplified: the clamping screw is specified as M2.5×6.5 and requires a T8 Torx key for secure fixation, while the shank is specified as J11‑F‑IK, enabling easy integration into compatible toolposts. The toolholder’s cutting height of 32 mm and modest weight of 0.11 kg make it suitable for medium-duty turrets that require precise height matching and low centrifugal load. These attributes reduce setup time, lower scrap risk and support a more predictable production flow when paired with standard VBMT inserts. Contact Metav Werkzeuge today for specialist advice on Teknik Cutting Tools SVJB toolholders and to arrange supply directly from our Emmerich facility Technical data Article number: AP558TM Manufacturer: Teknik Makina ISO designation: SVJBL 1212 Shank designation: J11-F-IK Facts Head width: 12 mm Head height: 12 mm Cutting head width: 12 mm Cutting height: 32 mm Overall height: 12 mm Overall length: 110 mm Cutting angle: 93° Weight: 0.11 kg Torx screw: M2.5×6.5 Torx key: T8 Special features Internal coolant For VBMT 1103 indexable inserts Left-hand orientation Compact 12×12 mm toolhead SVJBL 1212 geometry FAQ Which inserts are compatible with this holder? The holder is designed for VBMT 1103 indexable inserts; the seating and coolant channel match the insert geometry for reliable clamping. Does the toolholder provide coolant to the cutting edge? Yes, the holder includes internal coolant that feeds the insert seat to aid chip control and reduce temperature at the cutting edge. What is the cutting direction and approach angle? This is a left-hand holder with a 93° cutting angle, suited for left-hand turning and facing tasks. Which fastening components are required for insert clamping? Clamping is achieved with an M2.5×6.5 Torx screw; a T8 Torx key is used for tightening and removal. What shank designation and overall length should be considered for machine integration? The shank is specified as J11-F-IK and the overall length is 110 mm, which should be checked against turret capacity and toolpost clearance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SVJCL 1212 J11 For VCMT 1103 Indexable Inserts Left-Hand Cutting, 93° - Teknik Makina
Benefit from precise ISO clamping, reliable compatibility with VCMT 1103 indexable inserts and a compact 110 mm overall length for dependable left‑hand turning operations; order via Metav Werkzeuge or consult our specialists for application support. Clamping holder SVJCL 1212 — SVJC for VCMT Indexable Inserts, left‑hand — Teknik Makina The Clamping holder SVJCL 1212 is a left‑hand turning tool holder designed to carry VCMT 1103 indexable inserts for stable external turning and facing operations in small to medium lathes. *Compatible with VCMT 1103 inserts *Left‑hand orientation for reverse turning *Compact overall length 110 mm for tight setups *ISO designation SVJCL 1212 for standardised mounting Consistent cutting performance through engineered geometry The SVJCL 1212 design delivers a controlled cutting geometry that reduces vibration and improves surface finish when paired with VCMT 1103 inserts. The holder’s cutting angle of 93° and secure clamping arrangement maintain insert position under load, which enables predictable material removal rates and longer insert life. By stabilising the insert during engagement, cycle times become more consistent and tool change frequency is reduced, supporting higher throughput in production environments. Space‑saving design that keeps the workflow moving A modest overall length of 110 mm and a compact head with a 16 mm cutting‑head width allow reliable access in confined fixturing without compromising rigidity. The low mass — approx. 0.135 kg — and standard J11 shank interface simplify handling and indexing, which speeds up tool setup and reduces downtime between jobs. For workshop planners this means more efficient use of machine capacity and fewer interruptions during batch runs. Clear compatibility and practical benefits for everyday turning This turning holder accepts VCMT 1103 indexable inserts and is specified as a left‑hand tool, making it suitable for operations that require reverse cutting direction. The holder’s cutting height of 21 mm aligns insert geometry with common toolpost heights, avoiding additional shims or adjustments. The ISO marking SVJCL 1212 identifies the holder size and clamping format, ensuring interchangeability within standard tooling systems and simplifying inventory management. Robust functionality explained in plain terms An indexable‑insert holder clamps replaceable cutting tips rather than fixed single‑point cutters; this means insert replacements are quick and repeatable. The clamping mechanism on this holder secures inserts firmly to maintain the correct rake and clearance during cutting, which reduces chatter and improves repeatability. The left‑hand specification denotes the intended feed direction across the workpiece; selecting the correct orientation prevents unexpected tool marks and maximises process reliability. For secure supply and expert advice on selecting the right SVJC turning holder for a specific application, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com — +49 2822 7131930; Metav’s specialists will advise on integration and delivery. Technical data Article number: D384TM Manufacturer: Teknik Makina SKU: D384TM Facts Overall length: 110 mm Cutting height: 21 mm Holder height: 12 mm Holder width: 12 mm Cutting‑head width: 16 mm Weight: 0.135 kg Cutting angle: 93° Special features ISO designation: SVJCL 1212 Compatible inserts: VCMT 1103 Shank type: J11 Feed direction: left‑hand (reverse turning) Application: external turning and facing with indexable inserts FAQ Which inserts fit this holder? The holder is made for VCMT 1103 indexable inserts; the SVJCL 1212 clamping geometry secures the VCMT form for repeatable turning. Is this a left‑hand or right‑hand tool? This model is specified for left‑hand cutting direction, suitable for operations requiring reverse feed on the workpiece. What is the overall length and why does it matter? The overall length is 110 mm, which permits use in compact toolpost arrangements and reduces interference in tight setups. Can the holder be used on most lathes? The SVJCL 1212 holder uses a standard J11 shank interface and common ISO clamping, so it integrates with many lathe toolposts designed for indexable insert holders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SVJCR 1212 SVJC for VCMT 1103 Indexable Inserts, 93° Cut Angle, J11-F-IK, Internal Cooling, Right-Hand Cutting - Teknik Makina
Take advantage of a compact clamp holder that combines internal coolant, a 93° cutting angle and secure Torx clamping for consistent turning results. The combination of precision, durability and straightforward maintenance supports reliable throughput in small-batch and serial production. Order the tool directly via Metav Werkzeuge or consult the Metav advisors for application-specific guidance. SVJC clamp holder for VCMT indexable inserts — 93° cutting angle, internal coolant by Teknik Makina The SVJC clamp holder for VCMT indexable inserts is a right‑hand turning tool holder in a flat design, made for secure clamping of VCMT 1103 inserts during steel machining and general metal turning. Internal coolant for controlled chip evacuation Compatible with VCMT 1103 indexable inserts Robust 12 × 12 mm shank dimensions Secure clamping with M2.5x6.5 Torx screw Precision and performance where it matters This turning tool holder delivers reliable machining through its 93° cutting angle, a geometry that supports stable tool engagement in interrupted cuts and difficult-to-access contours. The integrated internal coolant feed helps to evacuate chips efficiently and reduce thermal load at the cutting edge, which in turn extends the life of the insert and reduces downtime. Thanks to the compact 110 mm overall length and low mass (0.1 kg), the holder minimises vibration and improves repeatable surface finish in short‑reach turning applications. Secure clamping and straightforward servicing Clamping integrity is achieved with a M2.5x6.5 Torx screw and a corresponding T8 key, ensuring repeatable seating of the insert and fast changeovers. The flat head design gives a low profile where clearance is limited, and the holder’s 12 × 12 mm shank and 12 mm head width provide a stable interface with common tool posts. Maintenance is uncomplicated: the screw and clamping geometry are standardised for predictable torque behaviour, helping preserve seat accuracy and reducing the need for frequent adjustments. Compatibility and application scope in production Designed specifically for VCMT 1103 indexable inserts, the clamp holder supports right‑hand turning operations and is suited to general steel working and similar materials. The ISO designation SVJCR 1212 and mounting option J11‑F‑IK make it straightforward to integrate into existing tool sets; the holder’s cutting height of 32 mm aligns the insert with typical tool‑post centres used in medium‑duty lathes. When combined with appropriate inserts, the assembly offers a dependable choice for workshops seeking an efficient, repeatable turning setup. Practical advantages for workshop efficiency Choosing a compact, cooled clamp holder reduces cycle variability and helps maintain tool life under continuous use. The unit’s modest footprint and standardised fastenings mean fewer special spares and easier logistics on the shop floor. For operations balancing throughput with flexibility—such as prototype runs or mixed production—the holder provides a pragmatic compromise between rigidity and accessibility, enabling quick insert changes while maintaining consistent clamping accuracy. Order the Teknik Makina SVJC clamp holder (AP527TM) via Metav Werkzeuge for a dependable, internally cooled turning solution; contact Metav Werkzeuge for tailored application advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: AP527TM Manufacturer: Teknik Makina ISO designation: SVJCR 1212 Mounting reference: J11-F-IK Weight: 0.1 kg Facts Shank width: 12 mm Shank height: 12 mm Head width: 12 mm Overall length: 110 mm Total height: 12 mm Cutting height: 32 mm Cutting angle: 93° Cutting direction: right Special features Internal coolant Compatible with VCMT 1103 indexable inserts Torx screw M2.5x6.5 Torx key T8 Flat head / low‑profile design FAQ Which inserts are compatible with this clamp holder? The SVJC clamp holder is designed for VCMT 1103 indexable inserts and pairs with standard triangular VCMT‑format grades for turning tasks. Is coolant through the holder available for high‑temperature operations? Yes, the clamp holder features internal coolant to support chip control and reduce thermal stress at the cutting edge during continuous turning. What fastening hardware is required for insert changes? Insert clamping is secured with a M2.5x6.5 Torx screw; a T8 key is used for tightening and removal to ensure consistent clamping torque. Can the holder be used for left‑hand turning? This variant is specified for right‑hand cutting direction; left‑hand operations require the corresponding left‑hand version. Is the holder suitable for tight‑clearance tool posts? The flat, low‑profile head and 12 × 12 mm shank make this holder appropriate for installations with limited overhang and reduced clearance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SVVCN 1212 SVVCN for VC-- Indexable Inserts For VC-- 1103 Indexable Inserts Innenkühlung Neutral Cutting Direction 72.5° - Teknik Makina
Benefit from robust clamping, precise 72.5° cutting geometry and direct compatibility with VC-- 1103 indexable inserts for dependable chip control and repeatable seating; order the clamping holder via Metav Werkzeuge or consult the Metav sales team for application matching. Clamping holder SVVCN 1212 – toolholder with 72.5° cutting angle for VC-- 1103 indexable inserts (Teknik Makina) Clamping holder SVVCN 1212 engineered as a compact toolholder for secure fixing of VC-- 1103 indexable inserts in neutral cutting operations across turning and profiling tasks SVVCN 1212 for VC-- 1103 indexable inserts 72.5° cutting angle for predictable chip flow Compact 12 mm width with 6 mm head width Neutral cutting direction for bidirectional use Consistent clamping for reliable production The SVVCN 1212 clamping system provides a stable interface between insert and holder, designed to reduce vibration and positioning error. With a 72.5° approach angle the holder supports controlled chip formation, which helps to extend insert life and maintain surface quality. The compact construction — 12 mm body width and a 6 mm cut-head width — minimises overhang and contributes to improved process stability. Where repeatability and uptime matter, this toolholder reduces fixture adjustments and machining interruptions. Faster production through simple integration This toolholder is specified for a neutral cutting direction, enabling flexible setup and reducing inventory complexity when both turning directions are required. The ISO designation SVVCN 1212 and the shank code J11 allow straightforward replacement and compatibility checks in existing tool posts and turrets. At an overall length of 110 mm and a weight of 0.127 kg, the holder is easy to handle and integrates with standard toolholding systems without extensive modification, supporting quicker changeovers and less downtime. Clear compatibility and safe handling Designed for VC-- 1103 indexable inserts, the holder secures the insert firmly while allowing correct seat alignment and clamping force distribution; this lowers the risk of insert movement under load. The specified cutting height 22 mm ensures alignment with common tool stations; installation requires standard clamping screws and follows established shop-floor procedures. For workshops seeking a compact, well-specified holder, this model delivers predictable performance for medium-duty turning and profiling applications. Select the Teknik Makina SVVCN 1212 clamping holder for robust seating of VC-- 1103 inserts and contact Metav Werkzeuge for rapid delivery and technical matching — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: D142TM Manufacturer: Teknik Makina Model designation: SVVCN 1212 Suitable for inserts: VC-- 1103 Dimensions & weight Height: 12 mm Width: 12 mm Cutting head width: 6 mm Cutting height: 22 mm Overall length: 110 mm Weight: 0.127 kg Cutting angle: 72.5° Features & compatibility Neutral cutting direction Shank designation: J11 For VC-- indexable inserts ISO designation SVVCN 1212 Brand: Teknik Makina FAQ Which inserts fit this clamping holder? The holder is designed for VC-- 1103 indexable inserts and secures them in the SVVCN 1212 seat for correct orientation and clamping. Is the cutting direction fixed to one side? The toolholder has a neutral cutting direction, making it suitable for setups that require bidirectional operation. What are the critical dimensions for installation? Key installation values include a body height of 12 mm, overall length 110 mm and a cutting head width of 6 mm; these values help verify fitment in the toolpost. Can this toolholder be used for heavy roughing operations? The design prioritises stable clamping and predictable chip control; for heavy roughing, assess cutting parameters and insert grade to match the holder’s geometry and the machining forces. How is the insert secured in the holder? The holder uses a standard clamping arrangement compatible with VC-- 1103 inserts; correct torque on the clamping screw ensures secure seating and repeatable positioning. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Toolholder for TCMT 16T3 Indexable Inserts 91° Cutting Angle, Right-Hand - Teknik Makina
Take advantage of a robust clamping solution that combines secure insert retention, standardised shank dimensions and a neutral cutting geometry to keep turning operations efficient. The holder’s compatibility with TCMT 16T3 indexable inserts and its right-hand configuration minimise setup complexity and support consistent surface finishes. Order the clamp holder directly via Metav Werkzeuge or request further technical advice from our consultants. Clamp holder D472TM for TCMT 16T3 indexable inserts — right-hand, 12 × 12 mm shank (Teknik Makina) A Clamp holder D472TM engineered to secure TCMT 16T3 inserts for right-hand external turning, offering standard shank dimensions for easy integration into common toolposts. Secure clamping for TCMT 16T3 inserts Right-hand cut orientation, 91° approach angle 12 × 12 mm shank fits standard toolholders Torx T15 screw with M3.5×8.5 fastener Consistent cutting geometry for reliable turning performance The clamp is built to provide secure clamping of TCMT 16T3 indexable inserts, delivering a repeatable interface between insert and holder that reduces micro-movement under load. The nominal 91° approach angle establishes a near-neutral cutting geometry that is well suited to general external turning tasks and helps to balance radial cutting forces. With a compact head and defined cutting height, the toolholder supports steady chip formation and contributes to longer insert life through reduced vibration and predictable contact conditions. Fast insert changes and maintenance-friendly fastening Designed with workshop efficiency in mind, the holder employs a Torx T15 drive and an M3.5×8.5 fastening screw for straightforward insert clamping and removal. This proven fastening standard speeds up indexable insert replacement and maintenance routines, lowering machine downtime. The combination of a clearly defined screw interface and robust clamping geometry ensures repeatable seating of the insert, minimising the need for frequent re-adjustment and thereby improving overall process uptime. Compact shank and stable construction for easy integration A 12×12 mm shank and a 16 mm cutting head width make this holder simple to fit into standard toolposts and quick-change systems common in small to medium-sized lathes. The 22.5 mm cutting height and the modest mass (approx. 0.136 kg) mean the holder contributes only minimal inertial load while maintaining the rigidity required for stable turning. Marked to ISO designation 1212 and supplied as SKU D472TM, the construction suits routine workshop applications where predictable clamping behaviour and conformity to established toolholder standards are essential. Contact Metav Werkzeuge for application advice on the Teknik Makina D472TM clamp holder and to arrange supply from our Emmerich stock. Technical data Article number: D472TM Manufacturer: Teknik Makina Product type: Clamp holder Label: Klemmhalter TCMT 16T3 ISO designation: 1212 Core data Shank width: 12 mm Shank height: 12 mm Cutting head width: 16 mm Cutting height: 22.5 mm Cutting angle: 91° Direction: right Weight: 0.136 kg Torx screw: M3.5×8.5 Torx key: T15 Special features Compatible with TCMT 16T3 indexable inserts Right-hand turning orientation SKU D472TM Compact, workshop-friendly dimensions FAQ What inserts are compatible with this clamp holder? The clamp holder is compatible with TCMT 16T3 indexable inserts; the pocket geometry and clamping arrangement are configured for that insert designation. Is this holder suitable for left-hand turning? This specific toolholder is configured for right-hand turning; a left-hand version is not indicated for SKU D472TM. What drive is required to tighten the clamping screw? A Torx T15 driver is specified for the M3.5×8.5 clamping screw used on the holder. Can the holder be mounted in standard 12 × 12 mm toolposts? Yes, the 12×12 mm shank is dimensioned for standard toolposts and quick-change adapters used in many workshops. What does the 91° cutting angle mean for machining? The 91° approach angle gives a near-neutral cutting geometry that helps distribute cutting forces predictably, aiding in stable external turning and consistent surface finish. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamp Holder 30° SRGCL 2525 M12 For RCMT 1204 Indexable Inserts Internal Cooling Left-Hand Cutting - Teknik Makina
Take advantage of the combination of reliable clamping, standard insert compatibility and a compact overall length for efficient left‑hand turning cycles; order this clamping holder directly via Metav Werkzeuge or ask our consultants if needed. Klemmhalter SRGC (SRGCL 2525) — clamping holder for RCMT 1204 indexable inserts, left‑hand, 30° cutting angle (Teknik Makina) A Klemmhalter designed as a left‑hand turning toolholder for standard RCMT 1204 indexable inserts, offering a 30° cutting angle and a secure M12 clamping interface for robust workshop use SRGCL 2525 ISO toolholder design Compatible with RCMT 1204 inserts 30° cutting angle for stable chip control M12 clamping screw, 150 mm overall length Increased stability and predictable chip control for left‑hand turning The clamping holder is engineered to provide consistent performance in left‑hand turning applications thanks to its 30° cutting angle, which promotes controlled chip formation and reduces the risk of chatter. The toolholder geometry and solid design deliver improved contact between insert and seat, which in practice means fewer vibrations and a more predictable surface finish on turned components. This stability is particularly relevant when machining medium‑duty parts where repeatable tolerances are required and cycle times must be maintained. Quick set‑up and broad insert availability to reduce downtime Designed around the widely used RCMT 1204 indexable inserts, the holder simplifies tooling logistics by accepting standard insert sizes that are readily available. The M12 clamping screw ensures a secure and repeatable clamping action while keeping set‑up straightforward; reduced set‑up complexity translates directly into less machine downtime. The ISO designation SRGCL 2525 identifies the holder form factor for compatibility checks, making it easier to integrate into existing toolpacks and programming routines. Compact dimensions with practical reach for workshop routines With a 25 mm holder height, 32 mm cutting‑head width and 150 mm overall length, the design balances rigidity and access to confined turning zones. The moderate mass of 0.744 kg contributes to stable tool dynamics without unnecessary inertia, supporting controlled feed rates and improved tool life under typical shop conditions. The toolholder’s compact footprint benefits smaller lathes and multi‑station turrets where space is at a premium, while still providing a secure platform for indexable inserts and straightforward maintenance procedures. Contact Metav Werkzeuge today for application guidance, availability from our Emmerich stock and tailored recommendations for the SRGCL 2525 clamping holder by Teknik Makina Technical data Article number: D291TM Brand: Teknik Makina Type: SRGC for RCMT Indexable Inserts ISO designation: SRGCL 2525 SKU: D291TM Facts Holder height: 25 mm Cutting‑head width: 32 mm Holder width: 25 mm Overall length: 150 mm Cutting height: 30 mm Cutting angle: 30° Cutting direction: left Clamping screw thread: M12 Weight: 0.744 kg Special features Compatible with RCMT 1204 indexable inserts Left‑hand turning configuration Designed for standard insert availability and fast replacements FAQ Which insert type fits this toolholder? The clamping holder accepts RCMT 1204 indexable inserts; the SRGCL 2525 form is optimised for that insert size and grade. What is the cutting direction of the holder? This holder is configured for left‑hand turning operations, as specified in the product data for the SRGCL 2525 by Teknik Makina (SKU D291TM). What are the key dimensions to check for machine compatibility? Relevant dimensions include a 25 mm holder height, 150 mm overall length and 32 mm cutting‑head width; these determine clearance and turret fit. Which clamping thread secures the insert? The tool uses an M12 clamping screw interface for insert retention and repeatable clamping torque. Is the holder suitable for compact lathes and multi‑station turrets? Yes — the compact dimensions and moderate mass (0.744 kg) make the holder suitable for machines with limited turret space while maintaining necessary rigidity for typical turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamp Holder 60° MTENN 2525 M22 For TN-- 2204 Indexable Inserts Innenkühlung Rechtsschneidend - Teknik Makina
Combining a standardised MTENN 2525 mounting with compatibility for TN-- 2204 indexable inserts and a compact 150 mm overall length, this clamping holder delivers repeatable turning performance and stable chip control; Order the Klemmhalter directly via Metav Werkzeuge or ask our consultants if needed. Klemmhalter MTENN 2525 — Clamping holder for TN-- indexable inserts, 60° cutting angle (Teknik Makina) A Klemmhalter engineered for turning operations with TN-- 2204 indexable inserts, providing secure clamping and consistent chip control for workshop and production environments *ISO designation MTENN 2525 for standardised fit *Compatible with TN-- 2204 indexable inserts *25 mm shank width and 25 mm shank height *60° cutting angle for controlled chip formation Precision mounting for repeatable turning results The MTENN 2525 designation ensures a standardised interface that simplifies tool change and repeatability in production. With a defined 60° cutting angle, the holder positions an indexable insert to promote stable cutting forces and predictable chip flow. Compatibility with the TN-- 2204 insert family means the toolholder integrates into existing indexable‑insert systems, reducing the need for custom tooling. For engineers and workshop managers this translates into measurable process stability and fewer setup iterations. Compact, rigid geometry to reduce vibration and setup time A short overall length of 150 mm combined with a 25 mm shank width and height lowers overhang and improves dynamic stiffness at the cutting edge. The narrow cutting‑head width of 12.5 mm keeps the tool profile compact, while a mass of 0.734 kg aids controlled acceleration and handling during set‑up. These dimensional choices reduce chatter susceptibility and shorten calibration cycles on lathes and turning centres. The result is less rework and more consistent surface finish on medium‑batch production runs. Practical compatibility for everyday workshop use Designed for turning operations, the holder accepts TN-- 2204 indexable inserts and carries the ISO name MTENN 2525, making it a practical choice for standard turning tasks. The bar designation M22 is provided for straightforward matching with boring bars and adaptors. In plain terms: an indexable insert system lets the cutting edge be replaced quickly without regrinding, so tool maintenance is faster and machine uptime increases. The robust clamping arrangement gives confidence in repeatable clamping force and long‑term positional stability. For dependable, standardised turning with TN-- inserts, source the MTENN 2525 clamping holder from Metav Werkzeuge in Emmerich for procurement advice and reliable supply Technical data Article number: D112TM Manufacturer: Teknik Makina Designation: MTENN for TN-- Indexable Inserts ISO designation: MTENN 2525 Facts Overall length: 150 mm Shank width: 25 mm Shank height: 25 mm Cutting‑head width: 12.5 mm Cutting height: 40 mm Weight: 0.734 kg Cutting angle: 60° Design and compatibility Compatible with TN-- 2204 indexable inserts Bar designation: M22 Application: turning with indexable‑insert systems Compact geometry for reduced overhang FAQ Which inserts are suitable for this holder? The Klemmhalter is specified for TN-- 2204 indexable inserts; use inserts of that designation to ensure correct seating and chip control. What is the significance of the 60° cutting angle? A 60° cutting angle positions the insert to balance radial and axial cutting forces, improving chip formation and helping to maintain consistent surface finish during turning. What are the key dimensions to consider for machine setup? Essential measurements are overall length 150 mm, shank width 25 mm, shank height 25 mm, and cutting‑head width 12.5 mm; these determine overhang and clamping clearances. Is the holder compatible with standard boring bars? The holder carries a bar designation M22, which facilitates matching with M22‑compatible boring bars and adaptors for secure mounting. Which manufacturer produced this toolholder and how is it identified? This item is produced by Teknik Makina and identified as MTENN 2525, SKU D112TM, for use with TN-- indexable inserts Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamp Holder 93° PDJNL 2525 M15 For DNMG 1506 Indexable Inserts Innenkühlung Left-Hand Cutting - Teknik Makina
Take advantage of a robust left‑hand clamping solution that combines precise insert compatibility and a rigid 93° cutting geometry for dependable turning performance; order directly via Metav Werkzeuge or consult Metav’s specialists for configuration advice. Klemmhalter PDJN for DNMG Indexable Inserts — left‑hand tool holder with PDJNL 2525 ISO designation by Teknik Makina Klemmhalter PDJN for DNMG Indexable Inserts is a left‑hand turning holder designed for facing and light turning operations with DNMG‑format inserts, delivering stable clamping and consistent cutter alignment for industrial workshops. Left‑hand orientation for facing operations For DNMG 1506 indexable inserts ISO PDJNL 2525 designation 150 mm overall length for deep reach Precise clamping for reliable turning results The holder is engineered to secure DNMG 1506 inserts with repeatable accuracy, reducing chatter and rework in batch production. Its PDJNL 2525 mounting geometry ensures consistent seat contact and predictable rake orientation, which translates into steady cutting forces and extended insert life. The left‑hand configuration and the 93° cutting angle combine to keep tool engagement stable on shoulder and face cuts, helping shops hit tolerances more reliably while maintaining throughput. Geometry and fastening that speed up setup times A compact head width of 32 mm and a holder width of 25 mm deliver a low‑profile design that facilitates access in confined setups and multi‑station lathes. The clamping arrangement, specified with an M15 screw interface for the tool‑post mounting, allows secure fixation with minimal torque variation, so changeovers are quicker and tool runout remains low. These aspects reduce setup time and increase uptime, supporting lean production without compromising rigidity. Built for practical reach and balanced handling With an overall length of 150 mm and a cutting height of 38 mm, this holder provides the reach necessary for recessed shoulders while retaining a compact centre of gravity; the result is improved handling during manual set‑up and reduced vibration during turning cycles. The component mass of 0.73 kg contributes to a stable assembly that limits deflection when machining medium to light steel workpieces, helping maintain surface finish and dimensional consistency in series work. A dependable option for systematic workshop workflows Chosen as part of a coordinated tooling system, the PDJN clamping solution supports standardised insert use and straightforward inventory management. The combination of an established ISO designation and a clear material of application for DNMG 1506 inserts simplifies procurement and training, while the left‑hand orientation expands capability for asymmetric machining tasks. This makes the holder a practical addition for workshops aiming to harmonise tooling across multiple machines and operators. For robust left‑hand turning applications, specify the PDJNL 2525 holder from Teknik Makina via Metav Werkzeuge — Metav’s specialists can advise on matching inserts and mounting options to suit the production task. Technical Data Article number: P124TM Manufacturer: Teknik Makina Designation (EN): PDJN for DNMG Indexable Inserts ISO designation: PDJNL 2525 ECLASS: 21181004 Numbers / Core technical data Overall length: 150 mm Cutting head width: 32 mm Holder width: 25 mm Holder height: 25 mm Cutting height: 38 mm Weight: 0.73 kg Cutting angle: 93° Designs / Special features For DNMG 1506 indexable inserts Left‑hand cutting orientation Shank / mounting designation: M15 Suited for industrial turning and facing operations FAQ What inserts fit this holder? The Klemmhalter PDJN for DNMG Indexable Inserts is designed specifically for DNMG 1506 format inserts and provides the correct seat geometry for secure indexing and repeatable positioning. Is the holder suitable for heavy roughing cuts? The PDJN holder by Teknik Makina offers a rigid 93° cutting geometry and a solid clamping design, which is suited for medium to light turning operations; for heavy roughing, selection should be matched to machine stiffness and insert grade. Which side does the holder cut from? This variant is configured for left‑hand cutting, intended for operations where tool engagement is required from the workpiece’s left side relative to spindle rotation. What mounting or shank designation is used? The tool holder is specified with an M15 mounting designation, enabling compatibility with appropriate tool posts and adaptors in standard lathe setups. How does the overall length affect machining access? An overall length of 150 mm provides extended reach for recessed features and shoulders while maintaining control over deflection and vibration for typical workshop tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamp Holder 93° SDJCR 2525 M11 For DCMT 11T3 Indexable Inserts Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of the combination of precise insert compatibility, a stable 25 x 25 mm shank and a compact 150 mm overall length for reliable turning operations; order directly via Metav Werkzeuge or consult the team for application advice. SDJCR 2525 clamping toolholder – SDJC for DCMT indexable inserts (right-hand) The SDJCR 2525 clamping toolholder is a right-hand turning holder designed to accept DCMT 11T3 indexable inserts for medium-duty external turning and facing tasks in general workshop and production environments. Compatible with DCMT 11T3 indexable inserts Right-hand cutting orientation Robust 25 x 25 mm shank 150 mm overall length for extended reach Consistent chip control and repeatable geometry for efficient turning The holder is engineered to secure DCMT 11T3 inserts with a stable clamping interface, which reduces micro-movement and improves surface finish on serial components. The 93° cutting angle provides a balanced approach between clearance and cutting force, helping to maintain tool life under typical machining feeds. In practice, a dependable clamping design lowers rework rates by limiting insert chatter, and the result is a more predictable process that supports tighter tolerances on turned parts. Rigid shank and compact length to increase stability and access A 25 x 25 mm shank combined with a 150 mm overall length gives a sturdy yet compact footprint for lathe setups where access and rigidity matter. The moderate mass of 0.735 kg contributes to vibration damping without making tool changes cumbersome. The 32 mm cutting head width and 30 mm cutting height are matched to the insert geometry so cutting forces are transferred evenly into the holder; this reduces edge wear on inserts and allows consistent finishing passes with fewer tool adjustments. Fast mounting and straightforward integration with standard toolposts The turning holder includes an M11 mounting characteristic for straightforward attachment where compatible posts or adapters are used, and the SDJC clamping concept allows quick insert indexing and replacement. For production environments, reduced downtime during insert changes and the use of standard DCMT 11T3 sizes mean less inventory complexity and faster cycle recovery. The combination of standard interface and robust construction supports reliable throughput and simplifies tooling management on the shopfloor. For supply and technical guidance on Teknik Cutting Tools' SDJCR 2525 clamping toolholder, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss compatibility with specific lathes and insert grades Technical Data Article number: D228TM Manufacturer: Teknik Makina ISO designation: SDJCR 2525 ECLASS: 21181004 Data Shank width: 25 mm Shank height: 25 mm Overall length: 150 mm Cutting head width: 32 mm Cutting height: 30 mm Cutting angle: 93° Weight: 0.735 kg Suitable for inserts: DCMT 11T3 Mounting thread: M11 Cutting direction: right Special features SDJC clamping concept for DCMT inserts Right-hand turning configuration Compact, rigid construction for reduced vibration FAQ Which insert size fits this holder? The SDJCR 2525 clamping toolholder accepts DCMT 11T3 indexable inserts as the standard size for its clamping pocket. Is the holder suitable for right-hand turning only? Yes, the holder is configured for a right-hand cutting direction and is intended for external turning and facing in that orientation. What are the shank dimensions and overall length? The holder features a 25 x 25 mm shank and an overall length of 150 mm, providing a compact but rigid setup for many lathe toolposts. How does the SDJC clamping system affect tool change time? The SDJC clamping design allows quick indexing and secure retention of inserts, which reduces changeover time and supports higher machine uptime. Can this holder be mounted to standard toolposts? The holder uses an M11 interface characteristic and is compatible with standard mounting arrangements where that thread or corresponding adapter is accepted. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamp Holder 93° SVJBL 2020 M16-IK For VBMT 1604 Indexable Inserts Interior Cooling Left-Hand Cutting - Teknik Makina
Take advantage of precise clamping, integrated internal coolant and proven compatibility with VBMT 1604 inserts for reliable turning operations; order via Metav Werkzeuge or consult our specialists for application advice. SVJBL 2020 clamping toolholder — Left‑hand turning holder with internal coolant by Teknik Makina The SVJBL 2020 clamping toolholder is a left‑hand turning holder designed for VBMT 1604 indexable inserts, offering through‑coolant capability for improved chip control and tool life. Left‑hand holder for VBMT 1604 inserts Integrated internal coolant channel 93° cutting angle for versatile turning 150 mm overall length for extended reach Improved cycle times through secure clamping and coolant supply The holder combines a robust clamping design with an integrated internal coolant channel, reducing setup time and improving cutting stability. The secure clamp interface minimises insert movement under load, which translates into consistent surface finish and fewer rework cycles. With the coolant routed directly to the cutting zone, chip evacuation and thermal control are enhanced — a practical advantage when machining alloys or longer workpieces where temperature and chip control influence part quality. Versatility in turning applications with standard insert compatibility Engineered for VBMT 1604 indexable inserts, the toolholder supports a wide range of carbide grades and chipbreaker geometries, enabling flexible process selection for finishing and semi‑roughing. The 93° cutting angle delivers a favourable approach for general‑purpose external turning, while the left‑hand orientation caters to specific machine setups and toolpath strategies. Compatibility with a standard shank designation (M16‑IK) and the supplied top plate reference (TA034) simplifies integration into existing tool assemblies. Practical assembly and service features that reduce downtime Designed for straightforward mounting and service, the assembly uses an M3.5x11 Torx screw and a T15 Torx key for clamping plate retention, enabling quick insert changes and secure fastening. The holder’s 150 mm overall length and compact head dimensions (head width 32 mm, body width 25 mm, height 25 mm) balance accessibility and stiffness, which is especially useful on lathes where reach and rigidity must be optimised. The modest mass of approximately 0.683 kg keeps tool overhang manageable while maintaining stability during cuts. Contact Metav Werkzeuge for detailed application guidance and to discuss suitability of the Teknik Cutting Tools SVJBL 2020 clamping toolholder for specific turning tasks — Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany; eMail: info@metav-werkzeuge.com; Tel: +49 2822 7131930 Technical data Article number: AP555TM Manufacturer: Teknik Makina ISO designation: SVJBL 2020 Intended inserts: VBMT 1604 Shank designation: M16‑IK Facts Overall length: 150 mm Holder height: 25 mm Head width: 32 mm Body width: 25 mm Cutting height: 40 mm Cutting angle: 93° Weight: 0.683 kg Special features Left‑hand orientation Internal coolant (through‑coolant) Top plate reference: TA034 Fastening: Torx screw M3.5x11 Required Torx key: T15 FAQ What inserts fit this holder? The SVJBL 2020 clamping toolholder is specified for VBMT 1604 indexable inserts and accepts standard VBMT geometries used in turning. Is the coolant internal or external? This holder provides internal (through) coolant, directing cutting fluid to the insert‑nose area for improved chip control and tool life. Which shank or boring bar designation is required? The toolholder is designed for a M16‑IK bar or bore stem, as indicated by the provided shank designation. Can the holder be used for finishing and roughing operations? Yes. With appropriate carbide grades and chipbreakers in VBMT 1604 inserts, the holder suits both finishing and semi‑roughing applications thanks to its secure clamp and 93° approach. What fastening parts are needed for maintenance? Replacement or service requires the M3.5x11 Torx screw and a T15 Torx key for top plate and clamp operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamp Holder 93° SVJCR 2525 M16 For VCMT 1604 Indexable Inserts Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a compact, right‑hand turning toolholder that combines ISO SVJCR 2525 compatibility with a 150 mm overall length for improved rigidity and straightforward insert replacement; order the part directly via Metav Werkzeuge or contact our consultants for application advice. Toolholder SVJCR 2525 – SVJC for VCMT Indexable Inserts (Teknik Makina) — Right‑hand turning, 150 mm overall length The SVJC for VCMT Indexable Inserts is a right‑hand turning toolholder engineered for secure clamping of VCMT 1604 inserts in standard external turning applications. *SVJCR 2525 ISO designation for standardised fit *Compatible with VCMT 1604 indexable inserts *Right‑hand turning with 150 mm overall length *Robust head: 32 mm width, 25 mm height Reliable clamping for consistent machining results The holder is designed around the SVJCR 2525 ISO interface and secures VCMT 1604 indexable inserts with a conventional clamping screw configuration, ensuring repeatability across multiple tool changes. The integrated M16 bore fastens the insert seat reliably, which reduces setup variation and minimises rework caused by inconsistent positioning. This results in shorter machine downtime and more predictable process outputs, making the component suitable for production lines where repeatable turning accuracy matters. Dimensions that increase rigidity and extend cutter life With an overall length of 150 mm and a toolhead measuring 32 mm wide by 25 mm high, the holder provides a stable platform that limits vibration during external turning. The specified cutting height of 40 mm and a cutting angle 93° contribute to optimal chip flow and controlled engagement for medium‑duty operations. The assembly weighs approximately 0.683 kg, a balance that supports steady clamping while remaining easy to handle during setup. The mechanical geometry is aimed at improving tool life by maintaining stable cutting conditions rather than relying on compensatory machining parameters. Simple integration and production readiness Configured for right‑hand operation, the toolholder integrates into conventional turret and toolpost setups and is a direct option where SVJCR holders are already standardised. Compatibility with the widespread VCMT insert family simplifies inventory and spares management, while the ISO designation supports rapid replacement without the need for special adaptors. For procurement, Metav Werkzeuge acts as a European quality filter and supply partner, offering consistent availability from stock and technical guidance for workshop integration. For purchase enquiries or detailed application guidance regarding the SVJCR 2525 toolholder, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — consultants are available to advise on fitment and machining set‑up. Technical Data Article number: D248TM Manufacturer: Teknik Makina Designation: SVJCR 2525 Product name: SVJC for VCMT Indexable Inserts Suitable inserts: VCMT 1604 Cutting direction: right Dimensions & Weights Overall length: 150 mm Head width: 32 mm Holder width: 25 mm Cutting height: 40 mm Weight: 0.683 kg Cutting angle: 93° Features & Compatibility M16 clamping bore ISO interface: SVJCR 2525 Compatible with VCMT 1604 indexable inserts Right‑hand turning orientation Designed for external turning applications FAQ Which inserts fit this toolholder? The SVJC for VCMT Indexable Inserts accepts VCMT 1604 indexable inserts and is designed for standard insert seating and clamping. Is the holder for right‑hand or left‑hand turning? This toolholder is configured for right‑hand turning operations. What is the ISO designation of the tool shank? The shank is specified as SVJCR 2525, matching common ISO toolholder standards. What are the key dimensions to check for machine compatibility? Key dimensions are an overall length of 150 mm, head width 32 mm, holder width 25 mm, and cutting height 40 mm. How is the insert secured to the holder? Clamping is achieved via the M16 bore and standard clamping hardware, providing secure seating for VCMT 1604 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamp Holder 95° DCLNR 2525 M19 For CN-- 1906 Indexable Inserts Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a robust, right‑hand toolholder that combines a 95° cutting angle with proven compatibility for CN-- 1906 indexable inserts, ensuring secure clamping and reproducible turning results; order directly via Metav Werkzeuge or request consultation from our specialists. Toolholder DCLN (DCLNR 2525) — right‑hand turning holder for CN-- inserts by Teknik Makina A Toolholder DCLN designed for right‑hand turning operations with CN-- indexable inserts, optimised for medium‑duty workshop and production turning tasks. Right‑hand turning holder DCLN Compatible with CN-- 1906 inserts 95° cutting angle for secure cutting 150 mm overall length, robust 0.82 kg Precision and stability for consistent turning performance The DCLN toolholder delivers stable chip control and reliable insert clamping through its 95° cutting angle, which reduces radial loads and helps maintain tool life. Its ISO designation DCLNR 2525 denotes a standardised shank geometry for predictable setup and repeatable positioning in the toolpost. For production environments where process stability matters, the holder’s dimensions and mass contribute to reduced vibration during turning, resulting in improved surface finish and consistent part tolerances. Fast setup and wide insert compatibility to save machine time Designed to accept CN-- 1906 indexable inserts, the holder simplifies insert changes and shortens setup cycles. The M19 bore designation and clear shank dimensions assist with secure mounting and alignment in common toolpost systems. With a cutting height of 40 mm and compact head width, this solution allows quick access to the insert seat and straightforward clamping, limiting downtime and enabling efficient changeovers between operations. Workshop durability and clear technical fit for everyday use Constructed for routine workshop demands, the holder’s 150 mm overall length and 0.82 kg weight offer a balance between reach and rigidity. The head width of 32 mm and shank width of 25 mm make the unit suitable for a broad range of turning tasks while keeping the tool overhang moderate. The right‑hand orientation and defined geometry support predictable chip flow and a secure interface with standard indexable turning plates, helping maintain throughput without frequent adjustments. Contact Metav Werkzeuge for personalised advice on the Teknik Makina DCLN toolholder (SKU D163TM); technical data and application guidance are available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: D163TM Manufacturer: Teknik Makina Designation: DCLN for CN-- Indexable Inserts ISO designation: DCLNR 2525 Cutting direction: right Facts Shank height: 25 mm Head width: 32 mm Shank width: 25 mm Cutting height: 40 mm Overall length: 150 mm Weight: 0.82 kg Cutting angle: 95° Special features Compatible inserts: CN-- 1906 Bore designation: M19 Right‑hand turning holder Standardised ISO shank geometry FAQ Which inserts fit this holder? The holder accepts CN-- 1906 indexable inserts; the DCLN design ensures proper seating and secure clamping for these plates. What is the cutting direction of the toolholder? This toolholder is specified for right‑hand turning operations and is manufactured to suit conventional right‑hand tool setups. What are the key dimensions to check for machine compatibility? Important dimensions include the 25 mm shank height, 32 mm head width, 150 mm overall length and the 40 mm cutting height; verify these against the machine’s toolpost and clearance requirements. Is the DCLN suitable for production use? Yes. The holder’s standardised geometry and robust mass provide stability for routine workshop and small‑series production tasks where reproducible results are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamp Holder 95° SCLCR 2525 M12-IK For CCMT 1204 Inserts Interior Cooling Right-Hand Cutting - Teknik Makina
Combining secure clamping for CCMT 1204 inserts with internal coolant and a stable 95° cutting angle, this holder delivers consistent right‑hand turning and reduced vibration. Benefit from the compact 150 mm overall length and straightforward Torx fixation for fast insert changes; order direct through Metav Werkzeuge or consult our specialists for precise implementation. SCLC for CCMT indexable inserts – SCLCR 2525 clamping holder (right‑hand, internal coolant) by Teknik Makina A SCLC for CCMT indexable inserts clamping holder engineered for right‑hand turning operations, offering internal coolant delivery and robust ISO SCLCR 2525 compatibility for medium‑duty lathe work Right‑hand cutting orientation Internal coolant for controlled flow Compatible with CCMT 1204 inserts ISO SCLCR 2525 toolholder design Accuracy and insert compatibility for reliable turning results The holder is designed around the CCMT 1204 insert family and the SCLCR 2525 ISO form, which together provide a reproducible insert seat and predictable cutting line. The slightly negative 95° cutting angle reduces radial load peaks and helps keep the workpiece concentric during finishing passes. For production contexts where repeatability matters, this configuration supports stable surface quality and consistent dimensional outcomes, reducing scrap rates and machine idle time. Robust clamping and quick serviceability to cut setup times A compact head width of 32 mm and a secure clamping geometry deliver repeatable seating and low vibration. The clamp is fastened with a Torx screw M4x11, operated with a T15 key, while the matching U‑plate is identified as TA015‑1 for straightforward replacement. With an overall length of 150 mm and a weight of 0.771 kg, the assembly balances rigidity and handling ease, so countertop setup is faster and tool swaps are less disruptive to cycle times. Coolant integration and operational advantages on the lathe Integrated internal coolant channels feed the insert area directly, improving chip evacuation and helping to manage cutting temperatures without external modification. The holder accepts a conventional M12‑IK bore interface for secure mounting and is optimised for right‑hand cutting direction in typical turning cycles. Together, these technical choices contribute to longer insert life and more consistent performance during extended production runs, while the compact form supports close‑quarters tool layouts on the turret. For practical purchasing or application advice regarding this Teknik Makina SCLC clamping holder (SKU AP503TM), contact Metav Werkzeuge for technical clarification or to arrange a supply — telephone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical Data Article number: AP503TM Manufacturer: Teknik Makina Type: SCLC for CCMT Indexable Inserts (SCLCR 2525) Brand: Teknik Makina Cutting direction: right Internal coolant: yes Dimensions & weight Overall length: 150 mm Head width: 32 mm Holder width: 25 mm Holder height: 25 mm Cutting height: 30 mm Weight: 0.771 kg Cutting angle: 95° Design & special features Compatible inserts: CCMT 1204 Fastening screw: M4x11 (Torx) Torx key size: T15 U‑plate: TA015‑1 Tool shank / bore designation: M12‑IK ISO designation: SCLCR 2525 FAQ What inserts fit this clamping holder? The holder is specified for CCMT 1204 indexable inserts; the SCLCR 2525 seating ensures correct positioning and chip control. Is the coolant internal or external? The toolholder features internal coolant, supplying fluid directly to the insert zone to aid chip evacuation and temperature control. Which cutting direction is intended for this toolholder? This design is for right‑hand turning operations, with geometry optimised for stable right‑hand cuts. What fastener and key are required for insert clamping? Clamping uses a Torx screw M4x11, tightened with a T15 key for secure and repeatable fixation. Can this holder be mounted on standard tool posts? The holder uses an M12‑IK shank/bore designation for turret mounting; ensure turret compatibility with this standard. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamping Holder 25mm Width 25mm Height 30° Rake Angle - Teknik Makina
Take advantage of a robust combination of extended reach and stable clamping for efficient turning operations; the compact cross-section and ISO conformity reduce tool changes and simplify inventory. Order directly via Metav Werkzeuge or consult our specialists for application guidance. Clamping holder L150 mm (P095TM) – 150 mm length, 25 x 25 mm cross-section, Teknik Makina A clamping holder L150 mm designed for secure tool mounting in machining applications, offering extended reach and standardised compatibility for workshop tool posts 150 mm overall length for extended reach 25 x 25 mm cross-section for stable clamping ISO 2525 standard shank for compatibility 30° cutting angle for controlled tool engagement Extended reach that reduces setup frequency The 150 mm overall length provides extra reach for components with deeper profiles, enabling fewer workpiece repositionings and a more efficient setup routine. The elongated design balances accessibility with rigidity, so the holder supports stable machining even when access is limited. With a mass of 0.594 kg, the component offers reassuring solidity without excessive weight, contributing to consistent tool behaviour and reduced vibration during cuts. Standardised shank for straightforward tool management Built to the ISO 2525 specification, the holder interfaces cleanly with widely used tool posts and fixtures, reducing the variety of adapters required in the tool crib. The 25 x 25 mm cross-section denotes the clamping envelope, ensuring a tight seat and reliable torque transmission. For purchasers managing stock, this standardisation simplifies procurement and minimises downtime caused by incompatible fittings — a pragmatic advantage for production-focused workshops. Geometry tuned for controlled engagement and durability A 30° cutting angle supports predictable chip formation and steadier tool entry, making the holder suitable for general turning tasks where surface quality and tool life are priorities. The robust construction and attention to machining tolerances translate into a dependable clamping solution for repetitive workflows. Supplied by Teknik Makina, the design aims to balance practical performance with ease of integration into existing setups, reducing the need for frequent adjustments. For dependable supply and tailored advice on Teknik Makina clamping solutions, contact Metav Werkzeuge for ordering and technical consultation at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — Metav Werkzeuge will assist with product selection and delivery to suit workshop needs Technical data Article number: P095TM Label: Klemmhalter L150mm Manufacturer: Teknik Makina Facts Overall length: 150 mm Weight: 0.594 kg Cross-section width: 25 mm Cross-section height: 25 mm Cutting angle: 30° eClass: 21181004 Special features ISO designation: 2525 Product type: Clamping holder Category path: Zerspanen > Klemmhalter UID: P095TM FAQ What machine interfaces is this holder compatible with? The clamping holder L150 mm (P095TM) conforms to ISO 2525, so it is compatible with machine tool posts and fixtures designed for that shank standard. Can the holder be used for deeper turned parts without extra supports? Yes, the 150 mm overall length provides additional reach; however, the stability of each setup should be evaluated and, where necessary, supplementary support or reduced overhang should be considered. How does the 25 x 25 mm cross-section affect performance? A 25 x 25 mm cross-section ensures a secure clamping envelope and good torque transmission, which helps to maintain cutting stability and consistent surface finish during operations. Is the 30° cutting angle suitable for general turning tasks? The 30° engagement angle is designed for controlled entry and predictable chip formation, making the holder well suited to a broad range of general turning applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamping Holder 25mm Width 25mm Height 30° Rake Angle, ISO 2525 - Teknik Makina
Take advantage of a compact, ISO‑standard interface and a 150 mm reach to improve turning stability and accessibility in constrained setups; the combination of a 25×25 mm cross section and a 30° approach angle supports consistent cutting results. Order the clamping holder directly via Metav Werkzeuge or request a technical consultation for integration advice. Clamping Holder L150 mm (Toolholder) – 25×25 mm, 30° by Teknik Makina The Clamping Holder L150 mm is a compact toolholder engineered for secure mounting and precise positioning in small to medium turning applications, offering an ISO‑standard interface for straightforward integration. ISO 2525 compatible mounting interface Robust 25×25 mm cross section 150 mm overall length for deep reach 30° cutting angle for universal turning Improved machining stability for consistent results The Clamping Holder L150 mm delivers measurable improvements in repeatability through its rigid 25×25 mm cross section and standardised ISO 2525 interface. These attributes reduce unwanted deflection during cut entry and exit, which in turn contributes to a more uniform surface finish and fewer corrective passes. For operations where part tolerances and cycle reliability matter, the reduced vibration and steady clamping position help to decrease rework and increase first‑pass accuracy, making the holder a sound choice for production and jobbing environments that prioritise process stability. Optimised reach and workshop versatility to increase throughput With an overall length of 150 mm, the toolholder provides extended reach for deeper bores and components with restricted access while maintaining adequate stiffness for routine turning tasks. The 30° approach facilitates favourable cutting engagement for a range of turning strategies, allowing simpler tool set‑ups and faster changeovers when paired with compatible insert systems. Because the holder adheres to a recognised interface standard, retrofitting into existing tool posts is straightforward, reducing machine downtime and supporting leaner workflow in mixed‑batch production. Durable construction, traceability and straightforward procurement The holder’s compact mass (approx. 0.594 kg) and precise form factor support robust day‑to‑day handling without compromising machine balance. Traceability is ensured via the stock reference P092TM, which simplifies ordering and inventory management. Supplied by Teknik Makina and distributed through Metav’s European logistics hub, the component benefits from consistent quality checks and reliable availability. For workshops seeking dependable tooling components that integrate seamlessly into established processes, this toolholder offers a pragmatic combination of durability and standards compliance. Contact Metav Werkzeuge today for a detailed specification match or to secure supply of the Teknik Makina clamping holder P092TM; Metav’s specialists in Emmerich provide prompt technical advice and order handling Technical data Article number: P092TM Label: Clamping Holder L150mm Product type: Clamping holder Facts Overall length: 150 mm Width: 25 mm Height: 25 mm Weight: 0.594 kg Cutting angle: 30° Special features ISO interface: 2525 Manufacturer: Teknik Makina ECLASS: 21181004 FAQ What standard interface does the holder use? The holder features an ISO 2525 interface, allowing straightforward mounting on compatible tool posts and carriers. What are the main dimensions and weight? Key dimensions are 150 mm overall length with a 25×25 mm cross section and a weight of approximately 0.594 kg for the P092TM item. Which machining tasks is this holder suited for? This clamping holder is designed for small to medium turning operations where a compact, stiff toolholder with a 30° approach is advantageous. How can the P092TM be identified for reordering? Reorder using the stock reference P092TM and the label Clamping Holder L150mm; these identifiers ensure traceability through Metav’s catalogue. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamping Holder 60° MTENN 2525 M16 for TN-- 1604 Indexable Inserts Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of reliable clamping with a 25 mm body and 150 mm overall length for stable turning and consistent chip control; the MTENN design enables quick insert changes and predictable tool performance. Order directly via Metav Werkzeuge or consult our specialists for spacing, compatibility and delivery options. Clamping holder MTENN 2525 – MTENN toolholder for TN-- 1604 indexable inserts, 25 mm body (Teknik Makina) The Clamping holder MTENN 2525 is a robust turning toolholder designed for secure seating of TN-- 1604 indexable inserts in general turning applications, combining compact dimensions with a standard ISO interface for workshop integration 25 mm body diameter for rigid support 150 mm overall length for stable overhang Compatible with TN-- 1604 indexable inserts 60° cutting angle for common turning profiles Consistent rigidity for precision turning A short, rigid clamping body reduces vibration and keeps cutting geometry stable; the 25 mm body width and 150 mm overall length deliver a compact span that improves surface finish and repeatability. The design translates into fewer reworks and steadier cycle times: by limiting deflection the holder supports the insert edge where accuracy matters most. The included 60° cutting angle aligns with common insert grades and turning strategies, making the unit suitable for diverse workshop setups while reducing the need for multiple toolholders. Fast insert changes and straightforward compatibility Designed around the MTENN ISO designation, this toolholder accepts TN-- 1604 indexable inserts and is prepared for routine insert replacement without specialised fixtures. The clamping geometry and M16 shank/interface allow a secure fit and predictable repeatability between changes, which shortens tool-change time and supports lean production. Material and coating details for inserts determine cutting data; pairing the holder with appropriate grades ensures optimum edge life and process stability. This combination supports higher throughput and fewer unexpected stoppages. Workshop-ready reliability and easy integration With a mass of 0.724 kg and a compact cutting-head width of 12.5 mm, the MTENN arrangement is easy to mount and balances well on common toolposts or turrets. The ISO designation MTENN 2525 simplifies procurement and machine setup, while the compatibility note for TN-- 1604 inserts helps planners standardise tooling. The result is a durable clamping solution that slots into existing tool inventories, lowers setup complexity and supports consistent production quality in small-batch and serial turning alike. Contact Metav Werkzeuge today for procurement and technical advice on the MTENN clamping holder with 25 mm body and 150 mm length Technical data Article number: D110TM Manufacturer: Teknik Makina ISO designation: MTENN 2525 Compatible inserts: TN-- 1604 Data Overall length: 150 mm Weight: 0.724 kg Body width: 25 mm Cutting head width: 12.5 mm Cutting height: 35 mm Cutting angle: 60° Special features For TN-- 1604 indexable inserts M16 shank/interface Product type: Clamping holder Brand: Teknik Makina FAQ What inserts are compatible with this holder? The clamping holder is specified for TN-- 1604 indexable inserts and the MTENN 2525 interface ensures correct positioning. Is the MTENN 2525 suitable for general turning tasks? Yes, the MTENN 2525 toolholder with its 60° cutting angle is aimed at standard turning profiles and common workshop applications. How does the holder affect machining accuracy? The compact 25 mm body and 150 mm overall length reduce deflection, improving surface finish and dimensional repeatability when the MTENN clamping holder is used. What mounting interface is used on the holder? The holder employs an M16 shank/interface and an ISO MTENN 2525 designation to match common turret and toolpost fittings. Can insert changes be performed quickly? Yes, the clamping geometry has been designed for straightforward, repeatable insert replacement to support efficient tool changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Clamping Holder 62.5° DDNNN 2525 M15 for DN-- 1506 Indexable Inserts Innenkühlung Rechtsschneidend - Teknik Makina
A compact, rigid clamping toolholder with a 25 x 25 mm shank, 150 mm overall length and compatibility with DN-- 1506 indexable inserts — delivering predictable cutting geometry and stable clamping. Order the Klemmhalter DDNNN 2525 directly via Metav Werkzeuge or ask our consultants if needed. Klemmhalter — DDNNN 2525 clamping toolholder for DN-- 1506 indexable inserts (Teknik Makina) A Klemmhalter clamping holder engineered to secure DN-- 1506 indexable inserts for compact turning applications, combining a standardised shank with a controlled cutting geometry. 25 x 25 mm shank for rigid clamping Compatible with DN-- 1506 inserts 150 mm overall length for compact setups 62.5° cutting angle for stable cutting Greater rigidity for steady machining results The DDNNN 2525 holder is designed around a 25 x 25 mm shank that prioritises rigidity and repeatability at the toolpost. This robust cross-section reduces vibration and deflection during cutting, which in turn supports improved surface finish and extended insert life. With the ISO DDNNN 2525 designation and a compact 150 mm overall length, the holder integrates into machining centres and lathes where a short overhang and predictable behaviour are required. The combination of structural stiffness and standard geometry makes this a practical choice for workshops seeking consistent turning performance. Secure insert clamping and predictable cutting geometry Clamping is arranged to accept DN-- 1506 indexable inserts and to maintain the correct seating under cutting forces. The toolholder presents a 40 mm cutting height and a 12.5 mm cutting‑head width that together position the insert reliably at the intended datum. A defined 62.5° cutting angle offers controlled engagement with the workpiece, aiding chip formation and dimensional hold. The M15 thread interface provides a straightforward mechanical connection for mounting or replacement, supporting quick insert changes and dependable repeatability under varied cutting conditions. Compact design for easy workshop integration At just 150 mm long and weighing 0.724 kg, this clamping toolholder occupies little bench or turret space while still delivering a solid toolholding solution. The modest footprint reduces interference in multi‑tool arrangements and simplifies setup in confined fixtures. Compliance with the DDNNN format ensures compatibility with standard indexable insert families, making inventory management easier. For production environments where uptime and consistent results matter, the holder’s combination of compactness and standardised dimensions helps streamline tooling routines and reduce changeover times. For tailored advice on Teknik Makina toolholders and to confirm compatibility with individual machines, contact Metav Werkzeuge — info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: D106TM Brand: Teknik Makina Compatible inserts: DN-- 1506 ISO designation: DDNNN 2525 Dimensions & Performance Shank height: 25 mm Shank width: 25 mm Cutting-head width: 12.5 mm Cutting height: 40 mm Overall length: 150 mm Weight: 0.724 kg Cutting angle: 62.5° Mounting thread/interface: M15 Features & Compatibility For DN-- 1506 indexable inserts ISO standardised DDNNN 2525 format Compact 150 mm footprint Clamping design for indexable inserts FAQ Which indexable inserts fit this holder? The holder accepts DN-- 1506 indexable inserts and is specified as DDNNN 2525 for correct fit and seating. What are the main dimensions to consider for fixture planning? Shank 25 x 25 mm, overall length 150 mm, cutting‑head width 12.5 mm and cutting height 40 mm; weight 0.724 kg. What cutting geometry does the toolholder present? The toolholder positions the insert at a 62.5° cutting angle to support consistent chip control and dimensional stability. Which mounting interface is required? A M15 interface is provided for mounting; check turret or toolpost compatibility before installation. Is this holder suitable for compact multi‑tool arrangements? Yes — the 150 mm overall length and standardised format make it suitable where a short overhang and compact tool layout are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Clamping Holder 62.5° DDNNN 3232 P15 For DN-- 1506 Indexable Inserts Innenkühlung Rechtsschneidend - Teknik Makina
Combining a robust 32 mm body, compatibility with DN--1506 indexable inserts and a precise 62.5° cutting angle delivers stable, repeatable turning performance; order the DDNNN clamping holder directly via Metav Werkzeuge or consult the Metav team for application advice. Klemmhalter DDNNN 3232 — DDNNN clamping holder for DN--1506 indexable inserts (Teknik Makina) A Klemmhalter DDNNN 3232 designed for secure mounting of DN--1506 indexable inserts in turning and grooving operations, suited to industrial workshop use Compatibility with DN--1506 inserts 32 mm body width for stable support 62.5° cutting angle for defined chip flow Durable 1.29 kg construction for minimal vibration Consistent clamping geometry for reliable part quality The DDNNN-style clamping holder provides a stable tool position that reduces vibration and machining variance. With a 32 mm body width and a defined 62.5° approach, the holder secures the insert so that cutting forces remain consistent cycle after cycle. This predictable geometry benefits repeatability on medium- to high-volume turning tasks and helps maintain dimensional tolerances without constant readjustment. The ISO designation DDNNN 3232 indicates the standardised fit and orientation that workshop engineers expect when integrating toolholders into established toolposts. Robust build to shorten set-up and boost uptime A rigid clamping interface and compact form reduce the frequency of re‑clamping and adjustment, resulting in lower set-up times between jobs. The compact head width of 16 mm and a cutting height of 40 mm allow integration into tight turret positions while preserving clearance for chip evacuation. The overall length of 170 mm balances reach and stiffness for a wide range of turning and profiling operations. The holder’s mass (1.29 kg) contributes to damping of transient cutting forces, which supports longer tool life for the inserts and steadier surface finishes on workpieces. Compatibility that simplifies inventory management Designed for use with DN--1506 indexable inserts and a P15 shank designation for the relevant boring bar range, the holder reduces the number of adapter types required across turning centres. Standardised interface dimensions mean that inserts from approved series seat reliably, so setting sheets and process windows remain stable when inserts are changed. For procurement and maintenance teams, this compatibility lowers the logistical overhead and simplifies reorder cycles while preserving machining performance. Practical advantages for workshop workflows The holder’s compact geometry and standardised ISO labelling enable fast identification and replacement on the shop floor. Reduced vibration and a well-defined cutting angle support improved surface integrity, which in turn decreases downstream inspection time and rework. For workshops seeking a balance between tool stability and flexibility, this clamping holder offers an efficient route to consistent production results with minimal adjustment effort. For tailored recommendations on mounting or process parameters, Metav Werkzeuge’s application specialists can provide machining guidance. Contact Metav Werkzeuge for precise application advice on Teknik Makina clamping holders and arrange procurement directly from Metav’s Emmerich hub Technical data Article number: D109TM Manufacturer: Teknik Makina Designation: Klemmhalter DDNNN 3232 For indexable inserts: DN-- 1506 SKU: D109TM Facts Body height: 32 mm Body width: 32 mm Head width: 16 mm Cutting height: 40 mm Cutting angle: 62.5° Overall length: 170 mm Weight: 1.29 kg eCl@ss: 21181004 Special features Compatible with DN--1506 indexable inserts ISO designation DDNNN 3232 Boring bar/shank designation P15 Suitable for turning and grooving operations Brand: Teknik Makina FAQ Which inserts fit this clamping holder? The clamping holder is designed for DN--1506 indexable inserts; compatibility is ensured by the ISO DDNNN 3232 interface. What is the cutting angle and why does it matter? A 62.5° cutting angle defines the insert approach and helps control chip flow and cutting forces, improving surface finish and repeatability. What are the key dimensions to check for turret clearance? Check the body height 32 mm, body width 32 mm, head width 16 mm and overall length 170 mm against available turret space. How heavy is the holder and what is the effect on machining? The holder weighs 1.29 kg, which contributes to vibration damping and increases rigidity for steadier cuts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamping Holder 93° Cut Angle SVJBR 2525 M16-IK For VBMT 1604 Indexable Inserts Internal Coolant Right-Hand Cutting - Teknik Makina
Achieve secure right-hand turning with internal coolant, precise compatibility for VBMT 1604 inserts and robust ISO SVJBR 2525 clamping — a compact solution engineered for repeatable results on production lathes; order the holder directly via Metav Werkzeuge or consult the team for fitment advice. SVJBR 2525 clamping holder – right-hand, internal coolant (Teknik Makina) The SVJBR 2525 clamping holder is a right-hand toolholder for turning applications with VBMT 1604 indexable inserts, designed for secure clamping and integrated coolant supply to improve chip control and tool life Right-hand turning with fixed 93° cutting angle Internal coolant for improved chip evacuation Compatible with VBMT 1604 indexable inserts ISO SVJBR 2525 form with 150 mm overall length Stable clamping for predictable turning accuracy A compact, purpose-built clamping solution ensures consistent contact between insert and holder. With a clamp height of 25 mm and an effective cutting height of 40 mm, the design reduces deflection during interrupted cuts and long turning passes. The head width of 32 mm and a nominal 93° cutting angle give a neutral engagement geometry that simplifies setup and reduces the need for repeated adjustments. For workshop planners this means fewer rejects and less rework: the holder translates insert geometry into reliable cutting performance, and the ISO designation SVJBR 2525 makes integration straightforward where standardised interfaces are used. Productivity gains through coolant and compact integration Integrated internal coolant directs cutting fluid close to the cutting edge, improving lubrication and chip evacuation for longer insert life and steadier surface finish. The compact shank design (M16-IK) and 150 mm overall length enable tight clearances on multi-tool turrets while the low mass (approx. 0.192 kg) helps reduce vibration transfer. The holder accepts the common VBMT 1604 insert form and secures it with a Torx fastener (T15), using a M3.5x11 screw and the matching TA034 locating plate for rapid, repeatable insert changes. These technical choices are made to support higher spindle speeds and uninterrupted production cycles, turning technical detail into measurable throughput gains. Practical fitment, applications and workshop confidence Designed for right-hand turning tasks, this clamping holder suits general machining shops, subcontract turning centres and in-house production lines that rely on standardised indexable inserts. The holder’s compact geometry is particularly useful for finishing passes and semi-finishing where rigidity and coolant access are decisive. Metav’s product curation and logistics mean the component is delivered from a quality-controlled stock in Emmerich with documentation and fast shipping options, providing a trustworthy supply channel for maintenance and production planning. For procurement and floor managers, the combination of standard ISO form, coolant capability and simple mechanical fixing offers a pragmatic balance between performance and operational ease. Contact Metav Werkzeuge for tailored advice on Teknik Cutting Tools SVJBR 2525 clamping holders and to confirm compatibility with existing toolposts and turret systems Technical data SKU: AP546TM Manufacturer: Teknik Makina ISO designation: SVJBR 2525 Article name: SVJB for VBMT Indexable Inserts Facts Overall length: 150 mm Clamp height: 25 mm Head width: 32 mm Cutting height: 40 mm Weight: 0.192 kg Cutting angle: 93° Special features Internal coolant: yes Direction: right-hand Compatible inserts: VBMT 1604 Shank / bore holder: M16-IK U-plate: TA034 Torx key: T15 Torx screw: M3.5x11 FAQ What insert type does this holder accept? The holder accepts VBMT 1604 indexable inserts and is supplied in the ISO form SVJBR 2525 (SKU AP546TM) for standardised fitment. Is coolant supply integrated in the toolholder? Yes — internal coolant is provided to direct fluid to the cutting zone, improving chip control and insert life. Which direction of cut is the holder designed for? This is a right-hand clamping holder intended for conventional right-hand turning operations. What mounting / shank interface does it require? The toolholder is specified with a M16-IK shank designation and suits compatible boring bars or toolposts designed for that interface. Are the fastening parts standardised for simple maintenance? Fastening uses a Torx T15 and a M3.5x11 screw together with the TA034 locating plate for quick and repeatable insert changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamping Holder 93° Cut Angle SVJCL 2020 K16-IK For DCMT 11T3 Indexable Inserts Internal Cooling Left-Hand Cutting - Teknik Makina
The combination of a secure clamp system and internal coolant ensures stable, long‑running left‑hand turning operations with consistent surface finish. Benefit from compatibility with DCMT/VCMT indexable inserts and robust geometry to reduce vibration and tool change time — order the holder directly via Metav Werkzeuge or request technical advice from our consultants. SVJCL 2020 clamping toolholder (SVJC for VCMT indexable inserts) — left‑hand with internal coolant The SVJCL 2020 clamping toolholder is a left‑hand turning tool designed for VCMT/DCMT indexable inserts, delivering secure clamping and integrated coolant for machining centres and conventional lathes. Left‑hand turning orientation (left) Internal coolant channel for reliable chip clearance Fits DCMT/VCMT indexable inserts Overall length 150 mm, robust 0.735 kg Stable performance for left‑hand turning and repeatable results Engineered for precision turning, this clamp‑style toolholder provides a defined cutting angle of 93°, which positions the insert for controlled chip formation and consistent contact pressure. The holder accepts standard DCMT/VCMT indexable inserts, enabling quick index changes and familiar insert geometry for toolrooms and production lines. Reduced setup time and repeatability are the primary benefits: repeatable seating and clamping lower scrap rates and shorten machine downtime, while established insert formats keep tooling logistics simple. Integrated coolant and secure clamping for longer insert life The internal coolant channel improves cooling at the cutting edge, supporting longer cutting intervals and more predictable tool wear. With the dedicated clamping plate TA034 and the supplied fastening hardware (Torx screw M3.5x11, Torx key T15), the insert is held firmly to minimise micro‑movement under load. This combination reduces thermal softening and edge chipping, which in turn increases productive cutting time and helps maintain surface quality on turned components — a direct economic advantage on medium‑ to high‑volume batches. Robust dimensions that enhance rigidity and reduce vibration With an overall length of 150 mm and a weight of 0.735 kg, the toolholder balances reach and rigidity for stable turning operations. Key dimensions such as a cutting height of 35 mm, a holder height of 25 mm, and a cutting‑head width of 32 mm contribute to a low‑vibration setup that supports better surface finish and longer insert life. The shank designation K16‑IK indicates the mounting profile, making integration into existing toolposts straightforward and ensuring secure support during heavy cuts. For technical consultation on integrating the SVJCL 2020 into existing setups or to request a quote, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — our specialists will advise on suitability and supply options Technical data Article number: AP535TM Manufacturer: Teknik Makina ISO designation: SVJCL 2020 Product type: SVJC for VCMT indexable inserts Facts Overall length: 150 mm Cutting height: 35 mm Holder height: 25 mm Cutting head width: 32 mm Holder width: 25 mm Weight: 0.735 kg Cutting angle: 93° ECLASS: 21181004 Special features Internal coolant: yes Fits inserts: DCMT 11T3 / VCMT Clamping plate: TA034 Torx screw: M3.5x11 Torx key: T15 Shank designation: K16‑IK Cutting direction: left FAQ Is this holder suitable for standard DCMT and VCMT inserts? The SVJCL 2020 holder is specified for DCMT 11T3 and compatible VCMT indexable inserts, enabling use of common turning inserts in production and repair workshops (AP535TM). Does the toolholder provide coolant to the insert tip? Yes — the holder includes an internal coolant channel, delivering coolant towards the insert to improve tool life and surface finish during sustained turning operations. What mounting or fastening parts are supplied? The holder is supplied with the designated clamping plate TA034 and uses a Torx screw M3.5x11 (Torx key T15) for secure retention of the insert seat. Can this holder be mounted in a standard toolpost with a K16 profile? The shank designation K16‑IK indicates compatibility with toolposts and boring bars accepting that profile; the holder offers straightforward integration where the K16 mounting is used. Is the SVJCL 2020 suitable for heavy roughing cuts? The toolholder’s robust geometry, defined cutting height and mass (0.735 kg) give it good rigidity for many turning tasks; assessment for heavy roughing should consider the machine power, insert grade and cutting parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamping Holder 93° Cutting Angle SVJCR 2525 M16-IK For DCMT 11T3 Indexable Inserts Internal Cooling Right-Hand Cutting - Teknik Makina
Take advantage of the combination of precise clamping, internal coolant and compact dimensions to maintain cycle-time stability and extend insert life; order the holder directly via Metav Werkzeuge or consult our tooling specialists for application-specific advice. SVJCR 2525 — SVJC for VCMT Indexable Inserts, internal coolant, right-hand SVJCR 2525 is a right-hand clamping holder designed for turning applications with VCMT/DCMT-style indexable inserts; ideal for medium-duty external turning where secure insert retention and coolant supply increase productivity. Right-hand turning orientation Internal coolant supply Compatible with DCMT 11T3 inserts ISO designation SVJCR 2525 Consistent right-hand turning for stable throughput The holder delivers repeatable clamping and a defined cutting geometry that reduces setup time and stabilises cycle times. With a right-hand orientation and a 93° approach angle, the toolholder is intended for conventional turning operations where predictable chip formation and tool behaviour are required. The overall length of 150 mm and compact head width minimise overhang, which in turn reduces vibration and supports more consistent surface finish and dimensional control—benefits that translate directly into fewer reworks and higher process reliability. Secure clamping and coolant to extend insert life A secure clamping mechanism, specified under ISO SVJCR 2525, holds DCMT/VCMT indexable inserts firmly and is tightened using an M3.5x11 Torx screw (T15), ensuring repeatable torque and seating. The integrated internal coolant channel supplies coolant directly to the cutting edge; this reduces thermal load, improves chip evacuation and commonly extends the service life of carbide inserts. For manufacturers seeking to lower tooling costs per component, the combination of firm clamping and directed coolant provides a measurable reduction in wear and a more stable cutting process. Compact footprint and straightforward integration Designed with a 25 mm shank width and a 25 mm holder height, together with a 32 mm cutting-head width, this clamping holder fits common turret and toolpost setups while keeping footprint small. The modest weight of 0.735 kg and standardised interface simplify handling and changeover; the holder accepts the common DCMT 11T3 insert form factor, which facilitates stocking and reduces inventory complexity. Where quick set-up is essential, the standardised dimensions and familiar screw interface enable rapid installation with existing tooling hardware. Practical advantages for workshop and production use Because the design focuses on proven interface standards and coolant-fed cooling, it suits both jobbing shops and production lines where repeatability and uptime are priorities. The robust construction and clear ISO designation make procurement and QA processes straightforward, while the compatibility with commonly used indexable inserts ensures broad applicability across turning tasks. Technical advisors are available to discuss specific workpiece materials and machining parameters to ensure the holder matches the intended application. Contact Metav Werkzeuge for tailored tooling recommendations and request the SVJCR 2525 right-hand clamping holder with internal coolant (AP526TM) — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: AP526TM Manufacturer: Teknik Makina Designation: SVJC for VCMT indexable inserts ISO designation: SVJCR 2525 Facts Cutting height: 35 mm Holder height: 25 mm Shank width: 25 mm Cutting-head width: 32 mm Overall length: 150 mm Weight: 0.735 kg Cutting direction: right Approach angle: 93° Compatible inserts: DCMT 11T3 Coolant: internal Special features Clamping plate: TA034 Torx screw: M3.5x11 Torx key size: T15 Right-hand orientation Suitable for VCMT/DCMT indexable inserts FAQ Which insert types fit this holder? The clamping holder is intended for DCMT / VCMT indexable inserts; the geometry matches DCMT 11T3-style inserts to ensure correct seating and cutting clearance. Does the holder provide coolant to the insert tip? Yes, the toolholder features an internal coolant channel that supplies coolant close to the cutting edge to support chip control and reduce thermal loading. What fastener is used to secure the insert? An M3.5x11 Torx screw is used for insert clamping; the required Torx key size is T15, providing consistent torque for repeatable clamping. Is this holder suitable for left-hand turning? No, the holder is specified for right-hand turning; left-hand operations require the corresponding left-hand variant. Can the holder be mounted in standard toolposts and turrets? Yes, the holder's standardised shank dimensions and ISO designation are compatible with common turret and toolpost interfaces used in turning centres. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Precision coolant delivery for demanding turning operations
Tool holders with internal coolant are precision components used in machining, particularly turning, to hold indexable inserts securely and feed them to the workpiece. Also referred to as through-coolant tool holders or internal coolant toolholders, these systems channel coolant directly to the cutting edge to reduce thermal load and improve chip control in heavy or high-speed machining.
How they work and where they help most
Standard holders without internal coolant rely on external nozzles, which can be blocked by chips and fail to reach the insert tip reliably. In contrast, holders with internal coolant contain integrated coolant channels and boreholes in the tool shank that guide the coolant under pressure straight to the insert. This targeted supply is particularly valuable for difficult-to-machine materials, high cutting speeds, deep cuts and internal turning where conventional coolant delivery struggles.
Key facts
| characteristic | detail |
|---|---|
| category | tool holders with internal coolant |
| common synonyms | internal coolant toolholders; coolant-through tool holders |
| typical application | turning, heavy machining, internal bore finishing |
| coolant routing | internal channels and boreholes delivering coolant to the insert seat |
| key technical effect | direct cooling at the cutting edge, improved chip evacuation, reduced thermal load |
| comparison | standard holders use external nozzles; internal coolant holders route coolant through the shank |
Measurable benefits for production
- Direct coolant feed reduces the thermal stress on the insert, extending tool life.
- Improved pressure at the cutting zone enhances chip evacuation, reducing recutting and tool damage.
- More consistent cooling helps achieve better surface finish and dimensional stability.
- Reliable coolant delivery under challenging chip conditions supports higher cutting speeds and heavier cuts.
Metav: precision supply and industrial competence
Metav positions itself as the practical partner for workshops and production: a European quality filter based in Emmerich that combines broad product availability with technical expertise. With over 48,000 customers and more than 250,000 products, Metav supplies through-coolant tool holders and related accessories with dependable logistics and application guidance, making sophisticated cooling solutions accessible for every workshop.
In short
Tool holders with internal coolant deliver targeted, high-efficiency coolant to the insert tip, improving chip control, tool life and surface quality in demanding turning tasks.
FAQ
When should I choose tool holders with internal coolant over standard holders?
Choose tool holders with internal coolant when external coolant nozzles cannot reliably reach the cutting edge, for deep cuts, internal turning, heavy machining or when machining difficult materials at high speeds. The internal coolant toolholders ensure direct cooling and better chip evacuation in these scenarios.
Can internal coolant toolholders be used with all insert types?
Internal coolant toolholders are compatible with most indexable inserts provided the holder and insert interface are specified for coolant-through operation. Verify seat type and manufacturer recommendations for coolant-through compatibility.
What performance improvements can I expect from coolant-through tool holders?
Typical improvements include longer tool life, fewer interruptions from clogged external nozzles, improved chip control and a more consistent surface finish due to reduced thermal distortion at the cutting edge.
How is coolant delivered inside an internal coolant toolholder?
Coolant is channelled through boreholes and internal passages in the tool shank directly to the insert pocket; this focused path creates sufficient pressure at the cutting edge to flush chips away and cool the insert effectively.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com