High-precision clamping holders with internal coolant for extended tool life
Clamping holders with internal coolant are designed to secure indexable inserts accurately while delivering coolant directly to the cutting edge, reducing thermal load and improving chip evacuation in demanding metalworking operations. Used for turning and internal machining of tough materials, these holders channel the coolant through built-in boreholes to the insert and beneath the chip, which boosts tool life and enhances surface finish. As a reliable system solution, the combination of clamping holder, internal coolant and indexable insert ensures consistent performance at high cutting speeds and under heavy cut conditions.
125mm PCLNR 2020 Tool Holder PCLN For CNMG Indexable Inserts, 95° Cut Angle, K12-IKG1/8, For CNMG 1204 Inserts, Internal Cooling, Right-Hand Cutting - Teknik Makina
Take advantage of a secure clamping system, internal coolant and precise compatibility with CNMG 1204 inserts for consistent turning performance; order directly via Metav Werkzeuge or consult our specialists for application advice. Klemmhalter PCLN for CNMG Indexable Inserts — Right-hand turning holder with internal coolant (PCLNR 2020) by Teknik Makina The Klemmhalter PCLN for CNMG Indexable Inserts is a right-hand turning holder engineered for external turning with CNMG 1204 inserts; it combines secure clamping and coolant feed to support reliable production runs Right-hand turning holder for CNMG 1204 Internal coolant for improved chip evacuation ISO designation PCLNR 2020 for standardised fit 125 mm overall length with 28 mm cutting height Consistent clamping for repeatable turning results The holder's ISO designation PCLNR 2020 signifies a standardised fit and makes insert changes straightforward. The PCLN-style clamp secures CNMG 1204 indexable inserts via a robust clamp screw (TH821) together with the matching U‑plate (TA016-1) and locating pin (TS-4), which ensures repeatable seating and reduces set-up time. This precise clamping reduces insert micro-movement under cutting forces, translating into stable tool life and fewer interruptions during batch production. Cooler cutting and improved surface finishes Built-in internal coolant supplies coolant directly to the cutting zone, helping to control temperature and evacuate chips more effectively. By reducing thermal load and swarf contact at the cutting edge, the holder can extend insert life and promote a more consistent surface finish on turned components. For operations that prioritise cycle-time reliability and dimensional repeatability, the coolant provision supports higher feeds and steady metal removal rates without sacrificing quality. Compact, rigid design for versatile turning operations With an overall length of 125 mm, a cutting height of 28 mm and a cutting head width of 25 mm, the toolholder balances reach and rigidity for general external turning tasks. The holder's right-hand orientation and a specified cutting angle of 95° make it suitable for facing and general-purpose turning where access and clearance are factors. Weighing 0.428 kg, the tool is easy to handle during mounting yet substantial enough to damp vibrations, supporting precise machining results across small to medium batches. Discuss application requirements with Metav Werkzeuge—our specialists can advise on the PCLN holder, mounting components and compatible CNMG 1204 inserts; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: AP130TM Manufacturer: Teknik Makina Facts Holder height: 20 mm Cutting head width: 25 mm Holder width: 20 mm Cutting height: 28 mm Overall length: 125 mm Weight: 0.428 kg Cutting angle: 95° Internal coolant: yes Special features ISO designation: PCLNR 2020 Suitable for: CNMG 1204 inserts Cutting direction: right Clamp screw: TH821 U‑plate: TA016-1 Locating pin: TS-4 Knee lever: TL4 Allen key: 3 Allen FAQ Is this holder compatible with CNMG 1204 inserts? The PCLN holder is designed for CNMG 1204 indexable inserts and secures them in the standard PCLNR 2020 seat. Does the holder provide coolant to the insert? Yes, the turning holder features internal coolant, supplying fluid to the cutting zone for improved chip control and temperature management. Which cutting direction is supported by the holder? This toolholder is specified for right-hand turning operations. What mounting components are included or required? The design pairs with the TH821 clamp screw, TA016-1 U‑plate and TS-4 locating pin; the knee lever is TL4 and an Allen key (3 Allen) is referenced for assembly. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Precision Caliper PWLNL 2020 PWLN for WNMG 0604, 95° Cutting Angle, Internal Cooling, Left-Hand Cutting K06-IKG1/8 - Teknik Makina
The combination of a secure clamping system, internal coolant and compact dimensions delivers reliable left-hand turning with reduced vibration and consistent surface finish; the robust TH617 clamping screw and standardised interfaces simplify integration into existing toolposts. Order the PWLN holder directly via Metav Werkzeuge or consult the advisers for tailored application support. PWLN for WNMG Indexable Inserts (PWLNL 2020) — Left-hand clamping holder with internal coolant A PWLN for WNMG Indexable Inserts clamping holder engineered for left-hand turning on lathes, offering internal coolant supply and a compact 125 mm overall length for enhanced rigidity and process stability Left-hand turning orientation Internal coolant supply Compatible with WNMG 0604 inserts Compact 125 mm overall length Precision clamping for stable turning and tool life The toolholder delivers secure clamping via the specified TH617 clamping screw and an ISO-compatible seat (PWLNL 2020), designed to accept WNMG 0604 indexable inserts. The holder geometry, with a 95° cutting angle, a head width of 25 mm and a nominal holder height of 20 mm, is arranged to reduce radial runout and minimise chatter. This rigidity translates into improved surface finish and longer insert life, meaning fewer interruptions for tool changes and a more predictable production flow. Coolant-through design to improve chip control and machining reliability Equipped with internal coolant, the holder channels cutting fluid close to the cutting edge, which enhances cooling and optimises chip evacuation. For processes where consistent temperature control matters, this feature helps maintain edge integrity and reduces thermal wear on the insert. The net effect is higher process reliability and the possibility of maintaining stable cutting parameters for longer machining cycles, supporting efficient batch production and repeatable component quality. Compact footprint that reduces overhang and eases integration With an overall length of 125 mm and a weight of 0.415 kg, this clamping holder reduces overhang and increases stiffness at the tool tip compared with longer assemblies. The compact dimensions allow closer positioning to the workpiece and a lower lever arm, which helps prevent deflection during heavy cuts. Standard accessory fitments — such as the U-plate TA021, roll pin TS3, knee lever TL3 and compatibility with shank type K06-IKG1/8 — make installation straightforward and ensure rapid repeatability when replacing holders or reconfiguring turret stations. Practical details that simplify workshop use The holder is supplied with the standard hex key size 2.5 Allen for adjustment and maintenance, and it supports a cutting height of 30 mm to match common turret setups. Its design focuses on compatibility and quick assembly: the standardised interface and accessory list reduce setup time and support consistent clamping force across tooling changes. For users seeking predictable machining cycles and reduced downtime, this configuration supports a pragmatic balance of performance and maintainability. Contact Metav Werkzeuge for application advice and request the Teknik Makina PWLN holder (AP165TM) to evaluate left-hand turning with internal coolant and compact rigidity Technical data Article number: AP165TM Manufacturer: Teknik Makina ISO designation: PWLNL 2020 Suitable for inserts: WNMG 0604 Cutting direction: left Overall length: 125 mm Holder height: 20 mm Head width: 25 mm Holder width: 20 mm Cutting height: 30 mm Cutting angle: 95° Internal coolant: yes Weight: 0.415 kg Clamping screw: TH617 U-plate: TA021 Roll pin: TS3 Knee lever: TL3 Hex key: 2.5 Allen Compatible shank: K06-IKG1/8 Numbers / Core technical data Overall length: 125 mm Holder height: 20 mm Head width: 25 mm Holder width: 20 mm Cutting height: 30 mm Cutting angle: 95° Weight: 0.415 kg Design / Special features Internal coolant supply Left-hand turning orientation ISO seat: PWLNL 2020 Compatible with WNMG 0604 inserts Standard accessory list (TA021, TS3, TL3) TH617 clamping screw Supplied hex key: 2.5 Allen FAQ What inserts does this holder accept? The holder accepts WNMG 0604 indexable inserts and uses the standard ISO seat designation PWLNL 2020 for secure seating. Is the holder suitable for left-hand turning only? Yes, the toolholder is configured for left-hand turning operations as specified in the product data. Does the toolholder provide internal coolant? Internal coolant is integrated into the holder to support improved chip evacuation and edge cooling at the cutting zone. Which accessories are compatible for assembly? Assembly and clamping reference parts include the TA021 U-plate, TS3 roll pin and TL3 knee lever; the clamping screw specified is TH617. What is the overall length and how does it affect rigidity? The overall length is 125 mm; the compact footprint reduces overhang, increasing rigidity and lowering the risk of deflection during heavier cuts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Precision Clamp Holder 95° DWLNL 2020 K08 For WN-- 0804 Indexable Inserts Innenkühlung Linksschneidend - Teknik Makina
Take advantage of a precise left‑hand clamping solution with a DWLNL 2020 profile and compatibility for WN-- 0804 indexable inserts; its 125 mm length and 95° cutting angle deliver consistent tool engagement and predictable chip flow. Order directly via Metav Werkzeuge or consult the technical team for integration support. Klemmhalter (DWLNL 2020) — clamping holder for WN-- 0804, left‑hand, Teknik Makina A sturdy Klemmhalter (DWLNL 2020) engineered as a left‑hand clamping holder for turning operations using WN-- 0804 indexable inserts, suited to precision workshop and production environments. DWLNL 2020 ISO holder for WN-- 0804 inserts Left‑hand orientation, 95° cutting angle 125 mm overall length for secure reach Compact 20 mm height and 25 mm head width Consistent turning performance through defined geometry The clamping holder is designed to provide repeatable tool positioning and reliable chip control in turning applications. With an ISO designation DWLNL 2020, the holder accepts WN-- 0804 indexable inserts and locates them at a 95° cutting angle, which helps maintain a stable cutting edge engagement and predictable cutting forces. The combination of standardised geometry and a firm clamping arrangement reduces set‑up time and supports higher process repeatability on series work. Easy integration into existing toolposts and bar setups A 125 mm overall length and a compact shank make this holder straightforward to fit into common toolposts or boring bar arrangements; the bores and profile correspond with standard bar designation K08, simplifying retrofits or replacements. The left‑hand orientation is specified for operations where the tool must cut in a counter‑clockwise direction; this specification removes ambiguity at ordering and during machine set‑up, shortening downtime and improving process planning. Compact form with practical dimensional benefits Key dimensions such as a 20 mm shank height, 25 mm head width and a 32 mm cutting height are balanced to provide a low‑profile but rigid solution. The holder’s modest mass (0.442 kg) contributes to lower centrifugal loads when used on rotating boring bars, while still offering the stiffness required for moderate turning tasks. These features support stable cutting performance without requiring oversized toolholders or adapters. Compatibility and handling explained for purchase decisions Compatibility with WN-- 0804 indexable inserts means insert selection governs achievable surface finish and cutting parameters; the holder itself provides the correct seat and clamping geometry to exploit the insert’s capability. The ISO DWLNL 2020 designation standardises expectations for seat angle and clamping location, aiding purchasing decisions and ensuring interchangeability with other DWLNL‑specification components. Practical note on application planning When specifying tooling for a machine line, note the left‑hand cutting direction and the holder’s 95° cutting angle to match insert geometry and spindle rotation. If a mirror‑image operation is required, select the corresponding right‑hand variant. The clear dimensional data and ISO labelling allow planners to check for interference, reach and clearance in CAM setups or on‑machine trials before production runs. For precise left‑hand turning with standard WN-- 0804 inserts, contact Metav Werkzeuge for tailored technical advice and secure supply of the Teknik Cutting Tools clamping holder D316TM; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application specifics and availability Technical data Article number: D316TM Description: DWLN for WN-- Indexable Inserts ISO designation: DWLNL 2020 Cutting direction: left Cutting angle: 95° Overall length: 125 mm Shank height: 20 mm Head width: 25 mm Holder width: 20 mm Cutting height: 32 mm Compatible inserts: WN-- 0804 Bar designation: K08 Weight: 0.442 kg Manufacturer: Teknik Makina Numbers Overall length: 125 mm Cutting angle: 95° Shank height: 20 mm Head width: 25 mm Holder width: 20 mm Cutting height: 32 mm Weight: 0.442 kg Special features ISO DWLNL 2020 Compatible with WN-- 0804 indexable inserts Left‑hand orientation Bar designation K08 DWLN holder type for turning applications Teknik Makina production FAQ Which inserts fit this holder? The clamping holder accepts WN-- 0804 indexable inserts; compatibility follows the DWLNL seating standard. What does the 95° cutting angle mean for machining? A 95° cutting angle positions the insert close to radial, providing a compromise between clearance and cutting edge support for stable turning. Is this holder right‑ or left‑hand? This tool is a left‑hand holder, specified for counter‑clockwise cutting directions relative to the workpiece. Which ISO designation applies? The holder conforms to DWLNL 2020 ISO designation, ensuring standardised seat geometry and interchangeability. What are the key dimensions to check before fitting? Confirm the 125 mm overall length, 20 mm shank height and 25 mm head width for reach and clearance in the machine setup. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Precision Clamp Holder PSSN For SNMG Indexable Inserts 45° PSSNR 2020 K12 For SNMG 1204 Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a compact, right-hand clamping solution that combines secure insert retention and straightforward integration into standard turning setups; the holder’s PSSNR 2020 design and compatibility with SNMG 1204 inserts support consistent cycle times and repeatable results. Order the clamping holder directly via Metav Werkzeuge or consult the Metav team for application-specific advice. PSSN for SNMG indexable inserts (P171TM) — PSSNR 2020 clamping holder, right-hand, 45° A right-hand PSSN clamping holder for turning with SNMG 1204 indexable inserts, engineered for stable clamping and compact toolsetting in general workshop and production turning applications. PSSNR 2020 shank design for stable clamping Compatible with SNMG 1204 indexable inserts Right-hand cutting at a 45° approach angle Compact dimensions: 20 x 20 mm shank, 125 mm overall Stable clamping that reduces vibration and improves repeatability The holder’s PSSNR 2020 geometry provides a rigid interface between toolholder and insert, reducing chatter and improving surface finish on turned parts. With a defined 45° approach angle and right-hand orientation, the component is optimised for conventional turning operations where predictable chip flow and consistent tool projection are required. The compact shank footprint (bold values below) keeps overhang low, which helps to maintain cutting stability and extend insert life while also simplifying toolpost arrangement in multi-tool setups. Quick set-up and clear compatibility for efficient workflows Designed for rapid integration into existing turning stations, the toolholder accepts SNMG 1204 indexable inserts and matches common clamping practices to reduce set-up time. The overall length of 125 mm and a shank section of 20 x 20 mm allow straightforward mounting in standard toolposts; the cutting head width of 25 mm and a cutting height of 30 mm deliver the necessary support for medium-duty turning operations. The nominal mass of 0.416 kg gives a balanced feel during handling and contributes to predictable dynamic behaviour at typical spindle speeds. Practical workshop use and flexible application range This clamping tool is suitable for right-hand finishing and light-to-medium roughing where SNMG inserts are preferred for their indexable versatility. The holder’s compatibility with a K12-style boring bar designation supports integration into modular tooling systems. As a compact, mechanically simple solution, the unit helps shops streamline tooling choices and maintain repeatable set-ups across batches. The product’s SKU P171TM identifies the specific holder model for ordering and stock control, and the Teknı̇k Makina design focus ensures the holder meets common industrial expectations for robustness and ease of use. Contact Metav Werkzeuge for tailored application advice or to request availability of the PSSN clamping holder (P171TM) for your turning operations; technical consultants in Emmerich will support specification and dispatch. Technical data Article number: P171TM Manufacturer: Teknik Makina ISO designation: PSSNR 2020 Facts Shank height: 20 mm Shank width: 20 mm Cutting-head width: 25 mm Cutting height: 30 mm Overall length: 125 mm Weight: 0.416 kg Cutting angle: 45° Cutting direction: right Suitable for inserts: SNMG 1204 Special features Compatible with SNMG 1204 indexable inserts ISO designation PSSNR 2020 Boring bar designation: K12 Right-hand clamping holder for turning FAQ Which indexable inserts fit this holder? The PSSN clamping holder is designed for SNMG 1204 indexable inserts; this compatibility enables rapid index changes and standardised insert sourcing. Is the holder suitable for heavy roughing? The PSSNR 2020 design offers good rigidity for light-to-medium turning; for heavy roughing, selection should be based on machine rigidity and insert grade rather than the holder alone. What are the key dimensions to check for mounting? Important dimensions include the shank 20 x 20 mm, overall length 125 mm, cutting-head width 25 mm and cutting height 30 mm, which determine fit in the toolpost and clearance for the workpiece. How is the product identified for ordering? Order using the SKU P171TM and the model designation PSSNR 2020; the holder is listed under Teknik Makina tooling lines. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Precision Clamp Holder PWLNL 2020 PWLN for WNMG 0804, 95° Cut Angle, Internal Coolant, Left-Hand Cutting - Teknik Makina
Take advantage of precise clamping, integrated internal coolant and a 95° cutting angle for consistent chip control and repeatable turning results; the compact 125 mm design reduces interference in tight set-ups. Order the clamping holder directly via Metav Werkzeuge or consult the Metav team for application advice. Klemmhalter PWLN for WNMG Indexable Inserts — left-hand clamping holder with internal coolant (Teknik Makina) The Klemmhalter PWLN for WNMG Indexable Inserts is a left-hand clamping holder intended for turning operations with WNMG 0804 inserts, offering integrated coolant delivery and a rigid PWLNL 2020-style mounting *Left-hand turning holder for WNMG 0804 inserts *Internal coolant for improved chip evacuation *95° cutting angle for stable facing and turning *125 mm overall length, robust 20 mm shank Increased process stability through precise geometry The clamping tool is engineered for repeatable performance: compatibility with WNMG 0804 inserts and the PWLNL 2020 mounting ensure a standardised fit across common indexable insert systems. The 95° cutting angle reduces radial forces during facing and roughing, which contributes directly to longer tool life and more predictable component tolerances. Because the toolholder is designed for left-hand orientation, it is immediately suitable for lathes and turning centres configured for left-hand operations, preventing setup ambiguity and minimising changeover time. Reliable chip evacuation and cooling for higher productivity Integrated internal coolant channels deliver cutting fluid close to the cutting edge, which aids chip control and heat dissipation during demanding cuts. The result is improved surface finish and reduced thermal wear on the insert, translating into fewer interruptions for regrinding or insert changes. Combined with the holder’s compact 125 mm overall length and a cutting height of 30 mm, the design balances rigidity and access, enabling higher material removal rates where stable clamping is required. Practical fastening and compact handling for workshop efficiency Clamping is secured using the designated TH821 clamping screw together with the matching U-plate TA020-1, dowel TS-4 and lever TL4, providing a secure, repeatable seat for inserts. The holder’s modest mass (0.425 kg) and a shank dimension of 20 × 20 mm make tool changes straightforward and reduce spindle load during acceleration. Basic maintenance and setup require only the supplied 3 Allen key sizes, so downtime for assembly or replacement is kept to a minimum. Application benefits and suitability This holder excels in turning tasks that demand consistent chip flow and coolant at the cutting zone: facing, light roughing and finishing on steel and alloy components where WNMG geometry is appropriate. The compact head width (25 mm) and robust shank provide a balance between accessibility and stiffness, which is particularly useful in confined tool pockets or multi-tool turrets. The result is fewer rejects, steadier surface quality and a predictable machining cycle time. For application recommendations or to secure the Teknik Cutting Tools clamping holder AP155TM, contact Metav Werkzeuge in Emmerich for tailored technical advice and prompt supply via e‑mail info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: AP155TM Manufacturer: Teknik Makina Designation: Clamping holder PWLN for WNMG indexable inserts ISO designation: PWLNL 2020 Core specifications Overall length: 125 mm Head width: 25 mm Holder width: 20 mm Holder height: 20 mm Cutting height: 30 mm Cutting angle: 95° Weight: 0.425 kg Insert size compatibility: WNMG 0804 Cutting direction: left-hand Internal coolant: yes Special features Clamping screw: TH821 U-plate: TA020-1 Dowel: TS-4 Knee lever: TL4 Allen key set: 3 Allen Compatible boring bar: K08-IKG1/8 FAQ Is this holder compatible with standard WNMG inserts? The clamping holder PWLN for WNMG indexable inserts is specified for WNMG 0804 inserts and uses the PWLNL 2020 mounting style to ensure a standardised fit. Can the holder be used with through‑coolant systems? Yes, the holder features internal coolant channels to deliver cutting fluid close to the cutting edge for improved chip control and cooling. Which cutting direction is supported by this toolholder? This toolholder is configured for left‑hand cutting direction, suitable for left‑hand turning set-ups or specific machining arrangements requiring left‑hand orientation. What fastening parts are required for installation? Installation uses the TH821 clamping screw, U‑plate TA020-1, dowel TS‑4 and knee lever TL4; the product specification AP155TM lists these matching components. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Precision Clamp Holder SDACR 2020 K11-F For DCMT 11T3 Inserts Interior Cooling Right-Hand Cutting - Teknik Makina
Take advantage of a compact, right-hand turning solution with DCMT 11T3 compatibility and a 90° cutting angle for reliable, repeatable machining; the holder’s 20 mm head dimensions and 125 mm overall length ensure easy integration into existing setups. Order or request advice directly via Metav Werkzeuge for assured supply and technical support. Clamping holder SDACR-F for DCMT indexable inserts (right-hand) – Teknik Makina A robust SDACR-F clamping holder designed for right-hand turning with DCMT 11T3 indexable inserts, suitable for workshop and production turning tasks. Right-hand turning, 90° cutting angle Compatible with DCMT 11T3 indexable inserts ISO designation SDACR 2020 20 mm head height and 125 mm overall length Consistent cutting results through rigid clamping and geometry The holder’s design delivers rigid clamping and stable tool presentation, which reduces chatter and improves surface finish during turning operations. With a 90° cutting angle and accommodation for DCMT 11T3 inserts the tool promotes predictable chip formation and repeatable toolpaths, translating into fewer scrapped parts and reduced rework. The arrangement is particularly beneficial when consistent axial positioning and reliable insert seating are required for batch production or precision jobbing. Simple compatibility for fast tool changes and setup Designed to the ISO SDACR 2020 shank standard, the clamping solution integrates smoothly with conventional toolposts and boring-bar systems identified as K11-F. The standardised interface enables quick mounting and exchange of indexable inserts, so changeovers are faster and machine downtime is reduced. At a weight of 0.397 kg and a compact 125 mm overall length, the unit balances rigidity with manageable mass for routine workshop handling. Economical tooling and suitability for mixed workshops By accepting replaceable indexable inserts, the holder reduces consumable costs compared with solid-tool alternatives: only the cutting edge is replaced while the main body remains in service. The compact dimensions—20 mm head height and 20 mm widths—make it suitable for confined setups where space and access matter, while the right-hand orientation supports standard turning directions. This combination of economy, straightforward maintenance and compact form factor suits both small specialist workshops and larger production environments seeking consistent turning performance. For precision right-hand turning solutions from Teknik Makina, rely on the SDACR-F clamping holder—contact Metav Werkzeuge for product availability and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D444TM Product name: SDACR-F for DCMT Indexable Inserts Model designation: SDACR 2020 Brand: Teknik Makina Weight: 0.397 kg Dimensions & core data Head height: 20 mm Head width: 20 mm Shank width: 20 mm Overall length: 125 mm Cutting angle: 90° Cutting direction: right Compatibility & special features For DCMT 11T3 indexable inserts ISO designation SDACR 2020 Boring bar designation: K11-F Right-hand turning tool FAQ Which inserts fit the clamping holder? The SDACR-F clamping holder is designed for DCMT 11T3 indexable inserts and secures them for standard turning operations. Is the holder suitable for left-hand turning? This holder is configured for right-hand turning with a 90° cutting angle; left-hand operations require a corresponding left-hand tool variant. What does ISO SDACR 2020 mean for mounting? ISO SDACR 2020 denotes the shank and head geometry standard, ensuring compatibility with toolposts and holders designed for that format. Can the holder be used in small jobbing shops? Yes, the compact 125 mm overall length and modest weight make the holder practical for both small workshops and larger production environments. How does the design help reduce tooling costs? By using replaceable indexable inserts, only the cutting edges are renewed when worn, extending the service life of the holder and lowering per-edge costs. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Precision Clamping Holder DCLNL 2020 K12 for CN-- 1204 Indexable Inserts, 95° Cut Angle, Left-Hand Cutting, Internal Cooling - Teknik Makina
Take advantage of a compact, purpose‑built clamp holder that combines reliable indexable‑insert compatibility with stable clamping and a short overhang for reduced vibration — ideal for left‑hand turning operations. Order directly via Metav Werkzeuge for fast delivery or consult the technical team for tailored set‑ups. Klemmhalter DCLN for CN-- Indexable Inserts (DCLNL 2020) — Left‑hand turning, 95° cutting angle — Teknik Makina The Klemmhalter DCLN for CN-- Indexable Inserts is a left‑hand turning toolholder designed for use with CN-- 1204 indexable inserts, offering a compact footprint and secure clamping for stable lathe operations Left‑hand orientation for reversing cuts Compatible with CN-- 1204 inserts 95° cutting angle for stable engagement Compact 125 mm length for tight setups Robust clamping with 20 mm holder height Stable cutting performance for left‑hand turning The DCLN‑style holder is engineered to provide predictable chip formation and consistent contact between insert and workpiece. With its 95° cutting angle and specification as DCLNL 2020, the design directs cutting forces into the tool body to reduce deflection. This results in improved surface finish and longer insert life when performing left‑hand turning or facing tasks. The combination of angle geometry and insert compatibility makes the holder suitable for repeatable production runs where process stability is essential. Space‑saving design that reduces overhang A short overall length of 125 mm and a compact cross‑section help to minimise tool overhang and vibration in confined toolposts. The holder’s 20 mm body width and 25 mm cutting‑head width are balanced to fit tight setups while maintaining rigidity. The modest mass of 0.441 kg further reduces inertial forces, making the component a practical choice for smaller lathes and workshops aiming to increase spindle speeds or shorten cycle times without sacrificing control. Secure clamping and straightforward insert handling Designed for CN-- 1204 inserts, the clamp mechanism gives repeatable seat alignment and reliable retention during interrupted cuts. The 20 mm clamp height and 30 mm cutting height ensure the insert is presented at the correct datum for consistent engagement. For users less familiar with indexable tooling: an indexable insert is a replaceable cutting tip that can be rotated or replaced when worn, delivering economical and fast restoration of cutting performance compared with brazed or tipped tools. Practical applications and target environments This holder suits workshops, maintenance departments and light production where left‑hand turning or reverse‑direction cuts are required. It is appropriate for general turning, profiling and facing when used with compatible CN-- 1204 inserts and a matching K12 shank designation for secure toolpost mounting. The technical specification supports efficient changeovers and predictable tool behaviour — key attributes when throughput and process reliability are priorities. For tailored advice on integrating the Teknik Makina DCLN holder into existing tool setups or for ordering assistance, contact Metav Werkzeuge — our experts in workshop precision are available to recommend the right combination for the application and to ensure prompt supply from Emmerich. Technical data SKU: D301TM Manufacturer: Teknik Makina Designation: DCLN for CN-- Indexable Inserts ISO designation: DCLNL 2020 Dimensions & weights Overall length: 125 mm Weight: 0.441 kg Holder height: 20 mm Head width: 25 mm Body width: 20 mm Cutting height: 30 mm Cutting angle: 95° Features & compatibility Compatible inserts: CN-- 1204 Cutting direction: left Shank / bar designation: K12 Application: indexable‑insert turning FAQ What inserts fit this holder? The holder accepts CN-- 1204 indexable inserts; the DCLN geometry is matched to that insert format for reliable seating and cutting. Is the toolholder suitable for left‑hand turning only? Yes — the toolholder is specified for left cutting direction and is intended for reversing cuts on lathes. What are the key dimensions to check for machine compatibility? Check the 125 mm overall length, 20 mm holder height and the K12 shank designation to ensure the holder fits the toolpost and provides sufficient rigidity. Which SKU and manufacturer should be referenced when ordering? Reference SKU D301TM and the Teknik Makina designation DCLN for CN-- Indexable Inserts when enquiring or ordering. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Precision Clamping Holder DVJNL 2020 K16 For VN-- 1604 Indexable Inserts Internal Cooling Left-Hand Cutting 93° - Teknik Makina
Benefit from the combination of a defined 93° cutting angle and a 40 mm cutting height that deliver stable engagement and predictable chip flow. The compact overall length and precise clamping reduce setup time and tool changes for small- to mid-series turning. Order the DVJN tool holder directly via Metav Werkzeuge or ask our consultants if needed. DVJN tool holder (DVJNL 2020) – for VN-- 1604 indexable inserts, 93° approach geometry (Teknik Makina) The DVJN for VN-- 1604 Indexable Inserts is a left-hand turning toolholder engineered for secure clamping and consistent approach geometry in CNC and lathe operations. 93° approach geometry for reliable cutting Compatible with VN-- 1604 indexable inserts Overall length 125 mm for compact setups Secure clamping, 20 mm holder width Greater process security through defined approach geometry The holder provides a 93° cutting angle, which creates a controlled engagement between insert and workpiece. This geometry reduces radial loading and helps to stabilise the cut in left-hand turning operations, delivering more predictable tool life and surface finish. The combination of 40 mm cutting height and the defined approach assists in consistent chip evacuation, which is particularly useful in repetitive turning tasks where repeatability is critical. Repeatable clamping and compact design for efficient setup Designed with a 20 mm holder width and a 27 mm cutting-head width, the toolholder is balanced for compact tool stacks and easy access in confined turret stations. The ISO designation DVJNL 2020 denotes compatibility with common mounting standards, and the solid construction ensures secure clamping of VN--type inserts. With a weight of 0.428 kg, the unit is light enough to reduce turret inertia while remaining rigid for production use. Simple integration with existing tooling and inserts Compatibility with VN-- 1604 indexable inserts means standard insert stocks can be used without modification, lowering tooling variety and spare-part inventory. The shank/boring-bar reference K16 and overall length of 125 mm permit straightforward installation in many turning tool posts and turrets. The left-hand orientation is specified for counter-clockwise feed directions, ensuring correct tool geometry when combined with standard turning programmes. Reliability for everyday workshop and CNC use The construction focuses on durability and straightforward operation: robust clamping, standard ISO form, and compact dimensions support frequent insert changes and predictable maintenance intervals. The precise approach geometry contributes to consistent results across runs, reducing scrap and the need for rework. The holder is suitable for both manual lathe setups and automated CNC environments where dependable performance is required. Contact Metav Werkzeuge today for tailored advice on integrating the Teknik Makina DVJN tool holder into existing setups and to discuss delivery options from our Emmerich facility. Technical data Article number: D343TM Manufacturer: Teknik Makina Type designation: DVJNL 2020 Product name: DVJN for VN-- 1604 Indexable Inserts Facts Overall length: 125 mm Cutting height: 40 mm Holder height: 20 mm Cutting-head width: 27 mm Holder width: 20 mm Weight: 0.428 kg Cutting angle: 93° Special features Compatible with VN-- 1604 indexable inserts Left-hand cutting direction Shank/boring-bar designation: K16 ISO-compatible toolholder form DVJNL 2020 Designed for indexable turning applications FAQ Which insert type fits this holder? The DVJN tool holder accepts VN-- 1604 indexable inserts and is prepared for standard VN-- insert geometries used in turning operations. Is this holder intended for left-hand turning? Yes, the holder is specified for left-hand cutting direction and is intended for operations that require counter-clockwise feed orientation. What are the overall length and weight of the tool holder? The overall length is 125 mm and the weight is 0.428 kg, values that support compact turret mounting with lower inertia. What ISO or designation identifies the holder? This toolholder is designated DVJNL 2020, matching common ISO toolholder forms for indexable inserts. Which shank size or boring-bar reference is applicable? The holder references K16 for the shank/boring-bar designation to assist with selection of compatible tool posts and adaptors. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Precision Clamping Holder SVJCR 2020 K11 For VCMT 1103 Indexable Inserts Innenkühlung Rechtsschneidend, 93° - Teknik Makina
Benefit from a rigid right‑hand clamping system and precise compatibility with VCMT 1103 indexable inserts to ensure steady turning and repeatable results; order directly via Metav Werkzeuge or consult the specialists for application guidance. Klemmhalter — SVJC holder for VCMT indexable inserts, right‑hand, ISO SVJCR 2020 A Klemmhalter designed as a right‑hand turning holder for VCMT 1103 indexable inserts, ideal for standard external lathe operations where reliable clamping and repeatable geometry are required. Right‑hand turning orientation Compatible with VCMT 1103 inserts 20 mm shank for stable mounting 93° cutting angle for consistent cuts Predictable rigidity for repeatable turning The holder delivers a stable clamping platform that reduces deflection in repetitive turning tasks. With a 20 mm shank and a compact 125 mm overall length, the assembly is engineered to be sufficiently rigid while remaining easy to integrate into existing tool posts. The 93° cutting angle supports predictable chip flow and light cutting engagement, which in turn helps to maintain consistent surface finish and dimensional accuracy over longer production runs. Seamless integration with common indexable inserts Designed to accept VCMT 1103 plates, the holder follows the SVJCR 2020 ISO designation for compatibility with widely available inserts. This standardised interface enables quick plate replacement and reduces tooling complexity at the machine, allowing a smooth transition between jobs or grades of carbide without swapping tool bodies. The result is shorter changeover times and improved shop-floor efficiency. Geometry that supports machining quality and process control A 33 mm effective cutting height and the right‑hand orientation are combined in a layout that helps to keep the insert in the intended cutting plane, improving repeatability across multiple setups. The holder’s geometry is intended to favour predictable tool life under stable cutting conditions; as insert seating and clamping are consistent, variance in part results is minimised. The tool’s relatively low mass (0.378 kg) also contributes to controlled dynamic behaviour at typical lathe speeds. Practical advantages for workshop workflows The compact dimensions — 20 mm shank height and width with a 25 mm head width — make the holder suitable for tight setups where space is limited but accuracy must not be compromised. The right‑hand configuration meets common turning requirements and simplifies stocking of tool holders for routine operations. Reliability is supported by a straightforward design that focuses on essential functions: secure clamping, standard insert compatibility and a utilitarian footprint conducive to varied lathe applications. For application-specific recommendations or to secure a batch of Teknik Cutting Tools SVJCR 2020 holders, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice and reliable supply coordination. Technical data Article number: D242TM Manufacturer: Teknik Makina Designation: Klemmhalter SVJC for VCMT Indexable Inserts ISO designation: SVJCR 2020 Facts Overall length: 125 mm Shank height: 20 mm Shank width: 20 mm Head width: 25 mm Cutting height: 33 mm Cutting angle: 93° Weight: 0.378 kg Special features For VCMT 1103 inserts Right‑hand orientation Bore designation: K11 Suitable for standard external turning FAQ Which insert type fits the holder? The holder is designed to accept VCMT 1103 indexable inserts; the interface complies with the SVJCR 2020 geometry specified for this class. Is the clamping direction left or right? This is a right‑hand tool holder; the right‑hand orientation ensures correct approach geometry for standard turning operations with VCMT 1103 plates. What are the shank dimensions and overall length? Shank dimensions are 20 mm × 20 mm with an overall length of 125 mm, giving the holder a compact profile suitable for constrained setups. How does the holder support machining repeatability? The holder’s fixed geometry, 93° cutting angle and secure seating for VCMT 1103 inserts contribute to repeatable cutting conditions and consistent part quality. What is the SKU and who is the manufacturer? The SKU is D242TM and the product is supplied by Teknik Makina under the designation SVJC for VCMT indexable inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm SCACR 2020 SCACR-F For CCMT Indexable Inserts For CCMT 09T3 Inserts Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a compact, precision clamping solution that combines compact dimensions, a stable 90° cutting geometry and reliable compatibility with CCMT inserts to keep turning operations consistent and efficient; order directly via Metav Werkzeuge or consult our specialists for application-specific advice. Klemmhalter — SCACR-F turning holder for CCMT 09T3, right-hand, 20 × 20 mm (Teknik Makina) The Klemmhalter SCACR-F is a right-hand turning holder designed for external turning with CCMT 09T3 indexable inserts, suited to conventional and CNC lathes where compact, repeatable clamping is required Right-hand turning orientation Compatible with CCMT 09T3 inserts 20 x 20 mm head and shank 125 mm overall length, 0.42 kg weight Stable clamping for repeatable turning cycles The SCACR-F holder delivers rigid clamping and a consistent seating for indexable inserts, ensuring predictable tool behaviour during serial turning operations. With a 20 x 20 mm head and shank profile and a compact 125 mm overall length, the design reduces overhang and vibration, which supports surface finish consistency and longer insert life. The 90° cutting angle provides a straightforward geometry for facing and straight turning, while the modest mass of 0.42 kg contributes to quick spindle response on smaller lathes. Optimised for CCMT 09T3 inserts and workshop workflows Engineered specifically for CCMT 09T3 indexable inserts, the holder follows the ISO designation SCACR 2020, allowing simple matching with commonly stocked inserts and predictable indexing. The clamping concept prioritises quick insert changes and secure fixation, which reduces downtime during tool swaps and increases throughput. The clear designation and standardised mounting simplify integration into existing tool sets and tool turrets, helping maintain production rhythm in both single-piece and batch environments. Practical integration and maintenance in everyday use Compact dimensions and standard ISO form mean straightforward handling and storage in a busy workshop. The robust construction supports repeatable positioning and straightforward inspection; routine checks focus on the clamping screw and seating surface only, keeping maintenance effort minimal. For shops that require dependable, no-frills holders for standard CCMT inserts, this design offers a balance of precision, durability and ease of use that fits into typical turning operations without elaborate setup. For professional advice on integrating the SCACR-F turning holder into existing tool systems, or to secure reliable supply from Emmerich, contact Metav Werkzeuge — our specialists will advise on compatibility and delivery options via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: D416TM Brand: Teknik Makina Article: SCACR-F for CCMT Indexable Inserts ISO designation: SCACR 2020 Core technical data Overall length: 125 mm Holder height: 20 mm Cutting head width: 20 mm Shank width: 20 mm Weight: 0.42 kg Cutting angle: 90° Special features For inserts: CCMT 09T3 Cutting direction: Right-hand ECLASS: 21181004 FAQ Which inserts are compatible with this holder? The holder accepts CCMT 09T3 indexable inserts; the SCACR-F geometry is matched to that insert size for reliable seating and indexing. Is the toolholder for left- or right-hand turning? This model is specified for right-hand turning applications, suited to standard right-hand cutting directions. What are the main dimensions and weight? Overall length is 125 mm, head and shank measure 20 x 20 mm, and the weight is 0.42 kg. What is the ISO designation of the holder? The holder is listed under SCACR 2020, the common ISO designation for this style of turning holder. Which production scenarios suit this holder best? The holder is ideal for lathe operations using CCMT 09T3 inserts where compact overhang, stable clamping and straightforward insert changes improve throughput. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm SDJCL 2020 SDJC for DCMT Indexable Inserts For DCMT 11T3 Inserts Innenkühlung Linksschneidend - Teknik Makina
Benefit from internal coolant and a precise fit for DCMT indexable inserts; the robust shank and a defined 32 mm cutting height deliver stable, repeatable turning results. Order the Klemmhalter SDJCL 2020 directly via Metav Werkzeuge or ask our consultants if needed. Klemmhalter SDJCL 2020 — Left‑hand toolholder with internal coolant (Teknik Makina) Klemmhalter SDJCL 2020 is a left‑hand toolholder for turning applications, designed for use with DCMT 11T3 indexable inserts and internal coolant supply Left‑hand cutting orientation Internal coolant supply For DCMT 11T3 indexable inserts ISO SDJCL 2020 designation Enhanced process stability through coolant delivery The integrated internal coolant channel ensures consistent lubrication and chip evacuation directly at the cutting edge, reducing heat and improving tool life. With a focused coolant feed, the holder supports longer uninterrupted runs and fewer tool changes, which contributes to higher machine uptime. This section highlights the holder’s capacity to maintain cutting conditions, rather than only listing dimensions, so production planners can expect more reliable cycle times and reduced rework. Accurate geometry for repeatable turning results Built to the ISO SDJCL 2020 profile, the clamping geometry offers a secure seat for DCMT 11T3 inserts and a repeatable insert position. The defined cutting height of 32 mm and a cutter head width of 25 mm guarantee consistent cutting geometry across batches. For work requiring tight tolerances, the stable insert clamping minimises deflection and supports predictable toolpath outcomes, which simplifies process qualification and shortens setup times. Compact design that fits workshop workflows With an overall length of 125 mm and a compact shank, the holder offers a balance between accessibility and rigidity in confined turret stations. The modest weight of 0.404 kg contributes to low centrifugal loads during high‑speed rotations while the left‑hand orientation and 93° cutting angle optimise chip flow for typical turning operations. The combination of compact size and solid construction supports flexible machine set‑ups and easier handling during indexable insert changes. Ready for integration and secure fastening Delivery features suitable fastening details for a fast fit on compatible tool posts: the holder accepts a Torx T15 drive and is secured with an M3,5x11 screw, while the U‑plate designation TA030 and toolbar rod reference K11 indicate common mounting interfaces. These attributes reduce adaptation effort when switching holders or integrating into existing turning stations, helping maintenance teams implement changes with minimal downtime. For reliable left‑hand turning with internal coolant, order the Teknik Makina SDJCL 2020 through Metav Werkzeuge — contact our team in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for application advice Technical Data Article number: AP516TM Manufacturer: Teknik Makina Product designation: SDJC for DCMT Indexable Inserts ISO designation: SDJCL 2020 Facts Overall length: 125 mm Cutting height: 32 mm Holder height: 20 mm Head width: 25 mm Shank width: 20 mm Weight: 0.404 kg Cutting angle: 93° ECLASS: 21181004 Suitable inserts: DCMT 11T3 Screw: M3,5x11 Torx key: T15 Special features Internal coolant Left‑hand cutting direction U‑plate: TA030 Toolholder rod: K11 Designed for DCMT 11T3 indexable inserts FAQ Which insert types are compatible with this holder? The holder is designed for DCMT 11T3 indexable inserts; the SDJCL 2020 geometry ensures secure seating for these inserts on Teknik Makina holders (AP516TM) Is the coolant delivered to the cutting edge? Yes — the Klemmhalter SDJCL 2020 features internal coolant delivery that channels fluid directly to the insert area to improve cooling and chip control Can the holder be mounted on standard toolposts? Mounting uses common interfaces: the U‑plate designation TA030 and toolholder rod K11 align with many turret systems for straightforward installation What orientation is the holder made for? This toolholder has a left‑hand cutting orientation and a 93° cutting angle, optimised for left‑hand turning operations Which torque or driver is required for the clamping screw? The holder uses an M3,5x11 screw with a Torx T15 drive for clamping and insert fastening Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm SRDCN 2020 SRDCN For RCMT 0803 Inserts, 20mm Width/Height, Neutral Cutting - Teknik Makina
Strong clamping for RCMT 0803 indexable inserts combined with a compact 20 mm shank ensures stable turning and fast changeovers for batch and single-part production. Take advantage of the SRDCN 2020’s 125 mm overall length and neutral cutting direction for versatile workshop use; order directly via Metav Werkzeuge or ask our consultants if needed. SRDCN 2020 clamp holder — neutral cutting direction, for RCMT 0803 indexable inserts (Teknik Makina) The SRDCN 2020 is a clamp holder designed for RCMT 0803 indexable inserts, providing secure insert retention and compatibility with standard 20 mm shanks for a wide range of turning tasks. Designed for RCMT 0803 inserts Neutral cutting direction for versatile turning 20 mm shank width and height Total length 125 mm, robust construction Secure insert clamping for consistent turning results The SRDCN 2020 offers reliable insert retention that reduces vibration and improves surface finish during turning operations. Compatible with RCMT 0803 indexable inserts, the holder secures the cutting edge precisely to provide repeatable results across batches. The clamping geometry has been engineered for stability, which shortens set-up time and lowers scrap rates by keeping the insert position constant even under intermittent cutting loads, making the tool holder a practical choice for production and repair workshops alike. Compact dimensions that speed up set-up and handling With a total length of 125 mm and a shank dimension of 20 mm x 20 mm, this clamp holder is compact yet accessible for rapid tool changes and straightforward mounting. The cutting-head width of 10 mm and a cutting height of 37 mm mean the holder fits neatly into existing tool stations while maintaining adequate reach for most turning tasks. Compatibility with K08 boring-bar interfaces simplifies integration into standard tool systems, reducing inventory complexity and enabling quicker responses to production changes. Robust build for dependable workshop performance Manufactured to industry expectations, the holder’s design emphasises mechanical rigidity and straightforward serviceability for daily use. The neutral cutting direction makes the unit adaptable to both conventional and atypical turning scenarios, while the modest weight of 0.358 kg keeps handling safe and convenient during tool changes. Backed by Teknik Makina’s engineering and supplied through Metav’s quality-filtered distribution, the clamp holder supports continuous production with a focus on reliability and predictable performance. For expert advice on integrating the SRDCN 2020 clamp holder into workshop tooling systems, contact Metav Werkzeuge for tailored recommendations and reliable supply from Emmerich — info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: D270TM GTIN: 4061905154065 Manufacturer: Teknik Makina Model: SRDCN 2020 Dimensions & weights Total length: 125 mm Shank width: 20 mm Shank height: 20 mm Cutting-head width: 10 mm Cutting height: 37 mm Weight: 0.358 kg Special features For RCMT 0803 indexable inserts Neutral cutting direction Compatible with K08 boring-bar designation Label: Klemmhalter SRDCN 2020 RCMT 0803 FAQ Which inserts fit this clamp holder? The holder accepts RCMT 0803 indexable inserts; the clamping seat and geometry are specified for this insert size on the SRDCN 2020 tool holder. Is the SRDCN 2020 suitable for both right- and left-hand turning? The SRDCN 2020 is specified for a neutral cutting direction, making it suitable for a wide variety of turning set-ups rather than being limited to a single hand. What are the mounting dimensions required for fitting the holder? Mounting requires a shank interface of 20 mm x 20 mm and a total available length of around 125 mm to accommodate the holder comfortably. Can the holder be used with standard boring bars? The holder is compatible with the K08 boring-bar designation, allowing straightforward integration into common tool systems. Who manufactures and distributes this tool? The tool is manufactured by Teknik Makina and distributed via Metav Werkzeuge; the product is listed under SKU D270TM (SRDCN 2020). Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Toolholder 20mm Clamp Width 16mm Clamp Height 30° Cutting Angle - Teknik Makina
Take advantage of the combination of a compact 125 mm reach, a firm 20 mm clamping face and a defined 30° cutting geometry for dependable tool positioning and steady machining results; order the clamping holder directly via Metav Werkzeuge or consult our specialists for application advice. Clamping holder L125 mm — tool holder with 20 mm clamping width and 30° cutting angle (Teknik Makina) A robust clamping holder L125 mm designed for secure tool mounting in precision turning and general metalcutting applications. 125 mm reach for deep tool positions 20 mm clamping width for firm seating 30° cutting angle for controlled engagement ISO 2020 shank for standard toolposts Accurate tool positioning for repeatable results The holder’s geometry provides a stable reference for turning operations: the 125 mm overall length offers reach without excessive overhang, while the 20 mm clamping face ensures a compact contact area that reduces lateral play. With a 30° cutting angle incorporated into the design, the assembly supports predictable tool engagement and consistent chip formation. These measurable characteristics translate into improved repeatability in series production and fewer tool-setting adjustments between setups. Compact form factor that fits standard toolposts Engineered to align with common workshop standards, the unit carries an ISO 2020 designation, simplifying integration into existing toolposts and fixtures. The moderate mass of 0.312 kg keeps inertia low, aiding stable dynamics during rotation and reducing the risk of chatter when used within recommended operating parameters. The compact footprint eases storage and handling while delivering the mechanical stability expected in a professional machining environment. Practical identification and traceability for production planning Traceability is supported by the clear marking and unique identifier P090TM, which simplifies stock management and replacement planning in busy shops. Supplied by Teknik Makina, the holder is suitable where a reliable, easily referenced clamping solution is required. The combination of standard dimensions and a defined profile reduces downtime for changeovers and helps maintain consistent part tolerances across batches. Procurement and workshop assistance for confident implementation For procurement and workshop integration the straightforward specification simplifies planning: defined dimensions, standard ISO compatibility and a concise product code accelerate ordering and inventory control. If further clarification is required on fitment or application, technical advisors are available to discuss suitability for specific machine tool environments, recommended clamping practices and any auxiliary accessories that support installation. For tailored advice on workshop compatibility and to arrange supply from Metav Werkzeuge — Manufacturer support and stock at Emmerich ensure fast dispatch; contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the Teknik Makina clamping holder (SKU P090TM) and suitability for the intended application Technical data Article number: P090TM Label: Klemmhalter L125mm Manufacturer: Teknik Makina Dimensions & weight Overall length: 125 mm Width: 20 mm Height: 16 mm Weight: 0.312 kg Cutting angle: 30° Standards & identifiers ISO designation: 2020 eClass: 21181004 Product type: Klemmhalter UID: P090TM FAQ What machines is this clamping holder suitable for? The clamping holder from Teknik Makina (SKU P090TM) is intended for standard turning toolposts that accept an ISO 2020 mounting; suitability should be checked against the lathe toolpost specification. How does the 125 mm length affect machining performance? A 125 mm overall length provides extended reach while keeping overhang moderate, helping the holder maintain rigidity and consistent positioning during machining when used as recommended. Is the clamping face dimension compatible with common insert holders? The 20 mm clamping width is a compact contact dimension that is compatible with many standard insert and holder arrangements; the specific interface should be verified for the intended insert system. Can the product be identified easily for reordering? Yes — the unit is listed under SKU P090TM and labelled Klemmhalter L125mm, which supports straightforward reordering and inventory control. What information helps decide if this holder fits the toolpost? Confirm the toolpost accepts the ISO 2020 shank and compare the overall length and clamping width (125 mm and 20 mm respectively) to ensure correct fitment. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Toolholder for SCMT 1204 Indexable Inserts 45° Right-Hand, 20mm Wide - Teknik Makina
Take advantage of the combination of secure clamping, a compact 20 x 20 mm square shank and a 125 mm overall length for stable, extended-reach turning with SCMT 1204 indexable inserts; order the clamping holder directly via Metav Werkzeuge or consult their specialists for application advice. Klemmhalter — clamping holder for SCMT 1204 indexable inserts, right-hand, 45° cutting angle (Teknik Makina) Klemmhalter is a precision clamping holder intended for turning with SCMT 1204 indexable inserts, offering a compact square shank and a 45° tool geometry for controlled chip flow and versatile lathe setups. For SCMT 1204 indexable inserts 125 mm overall length 20 x 20 mm square shank Right-hand, 45° cutting angle Secure insert clamping for reproducible turning cycles The holder provides a rigid, repeatable clamping solution designed for SCMT 1204 indexable inserts. The integrated clamping screw (M5x12) driven by a T20 Torx key ensures reliable axial retention and consistent seating of the insert, reducing vibration and improving surface finish. The ISO designation 2020 describes the tool geometry and seating interface, allowing straightforward replacement and compatibility checks across tool systems. Geometry that improves access and set-up speed A 20 x 20 mm square shank combined with a 125 mm overall length increases reach while maintaining stiffness for off-centre turning or operations in confined fixtures. The tool head offers a 25 mm cutting head width and 25 mm cutting height, making it suitable for both general turning and finishing passes. The 45° cutting angle directs chips away from the workpiece and toolholder, facilitating coolant flow and easier chip evacuation during continuous production. Designed for consistent production performance Configured for right-hand turning, the holder is engineered to deliver stable, repeatable results in batch and single-part production. With a mass of 0.374 kg, the assembly balances rigidity and manageable handling during tool changes. Manufactured by Teknik Makina, the construction focuses on durability and workshop efficiency, helping maintain cycle times and reduce downtime related to tooling adjustments or insert misalignment. Contact Metav Werkzeuge for tailored advice on application suitability and supply of the Teknik Makina clamping holder D466TM with its 45° right-hand geometry and SCMT 1204 compatibility Technical data Article number: D466TM Label: Klemmhalter SCMT 1204 L125mm Manufacturer: Teknik Makina Facts Overall length: 125 mm Weight: 0.374 kg Shank width: 20 mm Shank height: 20 mm Cutting head width: 25 mm Cutting height: 25 mm Cutting angle: 45° Torx screw: M5x12 Torx key: T20 Cutting direction: right Special features Compatibility: SCMT 1204 indexable inserts ISO designation: 2020 Product type: clamping holder eClass: 21181004 SKU: D466TM Category path: Zerspanen > Klemmhalter FAQ Which inserts fit this holder? The holder is made for SCMT 1204 indexable inserts; the clamping seat and geometry match the SCMT 1204 family for secure retention. Is the holder suitable for finishing passes? Yes; the 45° geometry and rigid 20 x 20 mm shank support finishing operations where stable contact and reduced vibration are required. What fastener is used to secure the insert? An M5x12 Torx screw is supplied for insert retention; the screw is driven with a T20 Torx key for reliable tightening. Can this tool be used for long-reach turning? The 125 mm overall length provides added reach while the square shank maintains stiffness for extended setups. What is the SKU and who manufactures the holder? The SKU is D466TM and the tool is manufactured by Teknik Makina, designed for workshop and production use. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Toolholder for SCMT 1204 Indexable Inserts Left 45° Cut, 20mm Width - Teknik Makina
Take advantage of robust secure clamping and a compact 125 mm reach combined with a 45° cutting geometry for consistent profile turning; order the clamp holder directly via Metav Werkzeuge or request further technical advice from our consultants. Clamp holder for SCMT 1204 indexable inserts — 125 mm, left-hand, Teknik Makina A clamp holder for SCMT 1204 indexable inserts engineered for left-hand profile turning and medium-reach applications. Secure clamping for SCMT 1204 inserts 125 mm overall length for extended reach 45° cutting angle for precise profiling Torx T20 screw, M5x12 for reliable fixation Reliable clamping and consistent reach for workshop turning The clamp holder is designed to accept SCMT 1204 indexable inserts and offers a full 125 mm overall length, providing a balance between accessibility and rigidity. The compact mass of 0.374 kg contributes to stable cutting conditions while the ISO 2020 designation clarifies the compatible toolholder geometry for inventory and tool management. The robust clamp geometry secures the insert during interrupted cuts, reducing vibration and supporting repeatable results across series production. Compatibility with a common insert standard lowers stocking complexity and streamlines tool changes for maintenance planning. Optimised geometry for precise profile and side cutting A defined 45° cutting angle and left-hand cutting direction make this holder suitable for profiling and external turning where access and chip flow require an acute approach angle. The 25 mm cutting head width and 25 mm cutting height establish clear seating for the insert, improving chip evacuation and surface finish when compared with blunt approach geometries. Fixing is handled via a Torx T20 interface and an M5x12 screw, providing secure torque transmission and simple, service-friendly removal using standard Torx tools commonly found in workshop tool kits. Practical workshop advantages and operational efficiency Fitting the clamp holder is straightforward thanks to standardised dimensions — 20 mm tool shank width and height — which simplifies clamping into common toolposts and reduces setup time between jobs. The unit’s measured specifications and consistent clamping behaviour support process reliability and contribute to fewer tool-related disruptions on the shop floor. For specialised applications or material-specific strategies, technical clarifications and compatibility checks are available to ensure the holder integrates seamlessly into existing tooling systems and production sequences. Request a technical consultation or a tailored quotation via Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 to arrange precise specifications and delivery options Technical Data Article number: D470TM Label: Clamp holder SCMT 1204 L125mm Manufacturer: Teknik Makina Facts Total length: 125 mm Weight: 0.374 kg Width: 20 mm Height: 20 mm Cutting head width: 25 mm Cutting height: 25 mm Cutting angle: 45° Torx key: T20 Torx screw: M5x12 Special features Compatible with SCMT 1204 indexable inserts Left-hand cutting direction ISO designation: 2020 Product type: Clamp holder FAQ What size of insert fits this holder? The clamp holder accepts SCMT 1204 indexable inserts, matching the insert geometry used in many turning operations. Is the holder suitable for right-hand machining? This holder is configured for left-hand cutting direction; right-hand machining requires a corresponding right-hand holder. Which screw and key are required for insert clamping? Clamping uses an M5x12 Torx screw tightened with a T20 Torx key for reliable fixation. Can the holder be mounted in standard toolposts? Yes — the 20 mm width and 20 mm height correspond to common toolholder dimensions for straightforward mounting. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Toolholder for VER16 Indexable Inserts, 20mm Width/Height, 22mm Cutting Head - Teknik Makina
Take advantage of a robust, precision-ready clamp holder that combines firm clamping, standardised compatibility and straightforward setup for consistent turning performance. The design supports VER16 indexable inserts and a compact 125 mm overall length for reduced overhang and improved rigidity. Order directly via Metav Werkzeuge or consult our specialists for configuration advice. Klemmhalter VER16 L125mm — Clamp holder for VER16 indexable inserts, 125 mm overall length, Teknik Makina A Klemmhalter VER16 L125mm engineered as a compact clamp holder for turning operations with VER16 indexable inserts, suited to workshop lathes and small turning centres. Secure Torx T15 clamping Compatible with VER16 indexable inserts 125 mm overall length for reduced overhang ISO 2020 designation for standardised fit Increased machining stability through a compact, standardised design The clamp holder delivers repeatable rigidity thanks to a compact 125 mm overall length, which reduces cantilever effects and helps maintain cutting stability during interrupted cuts. Intended for metalworking environments where consistent seating of indexable inserts matters, the holder is compatible with VER16 inserts and follows the ISO 2020 designation so replacement parts and inserts from standard ranges fit without adaptation. This standard compatibility reduces setup complexity and supports predictable machining results in both batch production and single-part turning. Faster clamping and reliable insert retention for reduced downtime Setup is straightforward: the clamping system uses a M3.5x8.5 mounting screw and a Torx T15 drive, enabling secure torque transmission with minimal cam-out and quick tool changes. The 22 mm cutting head width and 30 mm cutting height increase the contact area between holder and insert, improving lateral support and reducing micro-movements that cause chatter. At approximately 0.385 kg, the toolholder balances mass for rigidity without excessive inertial load on the turret, supporting stable feed rates and consistent surface finish. Workshop-ready compatibility and straightforward maintenance Designed for everyday use in industrial and craft workshops, the clamp holder keeps maintenance simple: insert replacement requires only the Torx key, and the standardised geometry means spare parts are widely available. The compact form factor allows installation in constrained turret pockets while preserving secure seating for cutting inserts. The product is listed under SKU D520TM, making ordering and stock checks straightforward for procurement teams. For operations seeking dependable, repeatable clamping performance, this toolholder provides a pragmatic balance of rigidity, serviceability and fit-to-industry standards. Contact Metav Werkzeuge to confirm compatibility and reserve stock of the Teknik Makina D520TM clamp holder at the Emmerich warehouse: info@metav-werkzeuge.com · +49 2822 7131930 Technical data SKU: D520TM Label: Klemmhalter VER16 L125mm Manufacturer: Teknik Makina Product type: Klemmhalter ECLASS: 21181004 ISO designation: 2020 Key measurements Overall length: 125 mm Clamping width: 20 mm Height: 20 mm Cutting head width: 22 mm Cutting height: 30 mm Weight: 0.385 kg Features and compatibility Compatible with VER16 indexable inserts Torx drive: T15 Clamping screw: M3.5x8.5 SKU reference: D520TM Product category: Clamp holder FAQ What inserts fit this clamp holder? The clamp holder is compatible with VER16 indexable inserts; the holder follows the ISO 2020 standard for straightforward insert selection. Which tool is required to tighten the clamping screw? A Torx T15 key is specified for the clamping screw (M3.5x8.5) to ensure secure, repeatable seating of the insert in the D520TM. Is this toolholder suitable for turret mounting on small lathes? The compact 125 mm overall length and 20 mm clamping width make it suitable for many turret pockets on small to medium turning centres, providing reduced overhang and improved rigidity. How does the cutting head geometry influence performance? The 22 mm cutting head width and 30 mm cutting height increase support for the insert, which helps reduce vibration and improves surface finish during typical turning operations. Can the holder be identified easily for reordering? Yes — the toolholder is listed as SKU D520TM and labelled Klemmhalter VER16 L125mm for straightforward procurement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
125mm Toolholder SDJC 2020 For DCMT 11T3 Inserts 93° Cutting Angle, Internal Coolant, Right-Hand - Teknik Makina
Take advantage of a coolant-fed, right-hand clamping solution that combines secure insert retention and compact dimensions for stable turning operations; order the SDJCR 2020 directly via Metav Werkzeuge or consult our tooling specialists for application advice. SDJCR 2020 clamping holder — SDJC tool holder for DCMT 11T3 inserts, right-hand, internal coolant (Teknik Cutting Tools) SDJCR 2020 clamping holder is a right-hand turning tool holder designed for DCMT indexable inserts; suitable for precise external turning where coolant feed and rigid clamping are required SDJC design for DCMT 11T3 inserts Right-hand turning orientation Integrated internal coolant feed Robust 20 x 20 mm shank for stability Secure insert seating for consistent machining The holder’s SDJCR 2020 geometry is tuned for stable clamping of DCMT 11T3 indexable inserts, delivering predictable seating and repeatable cutting performance. The clamping arrangement and the supplied M3.5x11 fixing screw ensure the insert is retained with minimal movement, which reduces vibration and protects the cutting edge. Compatibility with a widely used insert size simplifies tooling logistics and supports quicker tool set-up in small-series and production environments alike. Compact dimensions that improve toolpath reliability A compact but robust design—with a 20 x 20 mm shank, 25 mm cutting-head width and 125 mm overall length—provides a favourable stiffness-to-length ratio for turning tasks. The modest mass (approx. 0.404 kg) and precise geometry help to lower deflection under load, which in turn supports tighter tolerances and longer tool life. For workshop planners the short footprint and standard shank size make toolholder exchange and turret programming straightforward. Built-in coolant and serviceable components for uptime The internal coolant channel promotes efficient chip evacuation and targeted cooling at the insert rake zone, which can extend insert life and improve surface finish on difficult-to-machine materials. Practical service features—such as the T15 Torx drive for the clamp screw and the U-plate reference TA030—allow fast insert changes and straightforward maintenance. The holder’s 93° cutting angle and 32 mm cutting-edge height align with common lathe set-ups, reducing the need for supplementary fixtures or offsets. For coolant-fed right-hand turning where consistent insert retention matters, contact Metav Werkzeuge in Emmerich to request the SDJCR 2020 from Teknik Cutting Tools and discuss the best insert and clamp combinations for the intended application. Technical data Article number: AP511TM Manufacturer: Teknik Makina ISO designation: SDJCR 2020 Facts Overall length: 125 mm Shank: 20 x 20 mm Cutting head width: 25 mm Cutting-edge height: 32 mm Cutting angle: 93° Weight: 0.404 kg Special features For indexable inserts: DCMT 11T3 Direction: right-hand turning Internal coolant: yes Torx key: T15 Screw: M3.5x11 U-plate reference: TA030 Compatible toolholder bar: K11-IK FAQ What inserts fit this holder? The SDJCR 2020 clamping holder accepts DCMT 11T3 indexable inserts; the geometry and clamp screw configuration are matched to that insert designation. Is this holder for right-hand or left-hand turning? This tooling is configured for right-hand turning operations, as indicated by the SDJC orientation. Does the tool holder provide internal coolant? Yes — the holder features internal coolant feed to the insert zone to aid chip control and tool life. What shank size is required for the turret? The holder has a 20 x 20 mm shank and is intended for toolposts or turrets that accept that standard square shank. Which fastener and key are used for the clamping screw? Clamping uses an M3.5x11 screw secured with a T15 Torx key for reliable insert retention. What is the article number for reordering? The SKU for this product is AP511TM, handy for procurement and inventory management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Klemmhalter 72.5° SVVBN 1212 J11 For VBMT 1103 Indexable Inserts Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of the 72.5° cutting geometry and ISO SVVBN 1212 format to ensure stable, repeatable turning operations; the compact 110 mm overall length and 12 mm shank make it straightforward to integrate into existing toolposts. Order directly via Metav Werkzeuge or consult the specialists for application advice. Klemmhalter SVVBN 1212 – SVVBN for VBMT Indexable Inserts by Teknik Makina, 72.5° approach, 110 mm length Klemmhalter SVVBN 1212 is a compact tool holder designed for external turning with VBMT indexable inserts, combining precise geometry with standardised shank dimensions for reliable workshop use 72.5° cutting geometry for precise profiling ISO SVVBN 1212 designation for standard fit Compatible with VBMT 1103 indexable inserts 12 mm shank width and 110 mm overall length Stable cutting geometry for consistent surface quality The holder’s 72.5° approach angle is engineered to direct cutting forces evenly across the insert flank, reducing chatter and improving surface finish on external turning tasks. As a purpose-designed tool holder for indexable inserts, it supports controlled chip formation and predictable tool life, which translates into fewer interruptions on the shop floor and more consistent part tolerances. The orientation of the cutting edge is particularly advantageous for profiling and finishing operations where a defined entry angle reduces burr formation and downstream rework. Compact dimensions that simplify toolset planning With an overall length of 110 mm and a shank width of 12 mm, the holder fits common turret and toolpost arrangements without obstructing adjacent tools. The SVVBN 1212 ISO designation indicates the holder geometry and nominal cross-section, making it straightforward to match with existing tool carriers and adapters. The compact head width and a defined cutting height contribute to a low-offset setup that helps maintain rigidity; this minimises deflection and preserves the intended cutting geometry even under moderate feeds. Compatibility, handling and workshop benefits Designed for use with VBMT 1103 inserts, the clamping arrangement allows secure retention and repeatable index changes, cutting setup time and simplifying inventory management through standardised insert sizes. The holder’s light mass (approx. 0.129 kg) eases handling during tool changes while preserving sufficient mass for vibration damping in many turning applications. Supplied in a standard SVVBN configuration, the component supports quick retrofitting and reduces the need for bespoke toolholders, helping to streamline procurement and reduce downtime. Contact Metav Werkzeuge for tailored application advice and prompt supply from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: D131TM Manufacturer: Teknik Makina SKU: D131TM ISO designation: SVVBN 1212 Facts Overall length: 110 mm Shank width: 12 mm Cutting head width: 6 mm Cutting height: 25 mm Cutting angle: 72.5° Weight: 0.129 kg Special features Compatible inserts: VBMT 1103 Secondary designation: SVVBN for VBMT Indexable Inserts Toolholder type: clamping holder for indexable inserts Mounting reference: J11 FAQ What insert type fits this holder? The holder is specified for VBMT 1103 indexable inserts; the SVVBN geometry ensures correct seating and clamping for this insert format. Is the holder suitable for finishing passes? Yes, the 72.5° approach angle and rigid SVVBN configuration are optimised for finishing and profiling where controlled contact and reduced vibration are important. Which ISO designation identifies the shank and head geometry? The tool is designated SVVBN 1212, indicating the nominal shank dimensions and head form for compatibility with standard fixtures. Can this holder be used in standard toolposts without modification? The 12 mm shank and the ISO format are intended for standard turrets and toolposts; however, final fit depends on the specific machine carrier and adaptor used. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Precision Clamping Holder SVJCL 1212 J11-F-IK For VCMT 1103 Inserts Innenkühlung Linksschneidend - Teknik Makina
Take advantage of the combination of compact dimensions, reliable clamping and integrated internal coolant for consistent left-hand turning performance. Order the clamping holder directly via Metav Werkzeuge or consult our technical advisers for integration support. SVJCL 1212 clamping holder (SVJC for VCMT indexable inserts) — left-hand cut, internal coolant — Teknik Makina The SVJCL 1212 clamping holder is a compact, left-hand clamping solution for turning with VCMT 1103 indexable inserts, offering internal coolant and a robust Torx clamp screw. Compact 12 × 12 mm toolholder profile Internal coolant for improved tool life Compatible with VCMT 1103 indexable inserts Left-hand cutting with 93° cutting angle Precise clamping for stable left-hand turning The holder delivers repeatable positioning through a proven clamping geometry and an ISO designation SVJCL 1212, which ensures interchangeability across setups. Designed for left-hand cutting, the tool supports VCMT 1103 inserts, allowing predictable chip formation and consistent surface finish. The combination of a compact cross-section and a secure Torx screw system provides reliable clamping, which reduces vibration and contributes to longer insert life — a clear advantage for batch production and short-cycle work. Compact design that saves space and simplifies maintenance With a small cross-section of 12 mm × 12 mm and an overall length of 110 mm, the holder is intended for tight toolstations and multi-tool turret machines. The clamping screw specification M2.5×6.5 with T8 key access enables fast insert changes and straightforward maintenance. The compact form factor minimises interference when using adjacent tools and shortens set-up times, supporting higher machine utilisation and easier toolroom handling. Integrated coolant and geometry that improve process stability Internal coolant routing is built into the holder to deliver cutting fluid close to the insert rake, helping to control temperature and flush chips from the cutting zone. Coupled with a 93° cutting angle, the assembly is engineered for controlled cutting forces and effective chip flow on left-hand operations. This arrangement promotes enhanced tool life and more consistent component quality, especially in medium to high-material-removal tasks where thermal control matters. Practical compatibility and straightforward deployment The holder is specified to accept VCMT 1103 indexable inserts and is referenced by its ISO code, making it compatible with established tooling systems. At a weight of 0.1 kg, the component is easy to handle during set-up and rotation changes. The short list of attachment details and the standardised design reduce procurement complexity and simplify tool inventory management in the workshop or production cell. For left-hand turning operations that demand compactness and coolant-through capability, choose the Teknik Makina SVJCL 1212 clamping holder — request a quote or technical advice from Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application-specific integration. Technical Data Article number: AP537TM Manufacturer: Teknik Makina ISO designation: SVJCL 1212 Compatible inserts: VCMT 1103 Dimensions & weight Width: 12 mm Height: 12 mm Cutting head width: 12 mm Overall length: 110 mm Overall height: 12 mm Cutting height: 32 mm Cutting angle: 93° Weight: 0.1 kg Special features Internal coolant Left-hand cutting direction Torx screw M2.5×6.5, Torx key T8 Compatible with VCMT 1103 indexable inserts FAQ What inserts fit this clamping holder? The SVJCL 1212 clamping holder is designed for VCMT 1103 indexable inserts and offers correct seat support for those insert dimensions. Is coolant-through supported? Yes, the holder features internal coolant to supply cutting fluid directly to the insert rake for improved cooling and chip evacuation. Which cutting direction is intended for this tool? This holder is configured for left-hand cutting, with a tool geometry optimised for left-hand turning operations. What are the fastening details for the insert clamp? Clamping is provided via a Torx screw M2.5×6.5 and requires a T8 Torx key for tightening and release. What is the SKU and who manufactures the tool? The product is listed as AP537TM and manufactured by Teknik Makina; the ISO code for the holder is SVJCL 1212. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SCLCR 1212 SCLC For CCMT 09T3 Indexable Inserts, 95° Cut Angle, J09-F Mount, Right-Hand Cutting, Internal Cooling - Teknik Makina
A compact, right-hand clamping tool holder offering secure seating for CCMT 09T3 inserts, a 95° cutting angle and a slim 12 mm head for close turning operations; ideal where repeatable clamp force and quick insert changes are required. Order the tool holder directly via Metav Werkzeuge or ask our consultants if needed Klemmhalter SCLC for CCMT Indexable Inserts — SCLCR 1212 tool holder (Teknik Makina) A Klemmhalter SCLC for CCMT Indexable Inserts intended for right-hand turning, designed to accept CCMT 09T3 indexable inserts for medium to fine turning applications Compatible with CCMT 09T3 inserts ISO SCLCR 1212 holder type 12 mm head width and height 110 mm overall length Precise compatibility that reduces setup time The clamping solution is designed for repeatability: the SCLCR 1212 configuration guarantees consistent seat geometry for CCMT 09T3 inserts, which simplifies insert replacement and reduces downtime. With a slim head profile of 12 mm and an overall length of 110 mm, the holder allows confined tool positions and improved access to shoulders and grooves. The right-hand orientation and a 95° cutting angle deliver predictable chip flow and stable cutting forces, supporting efficient machining programmes in small-batch and serial turning. Robust clamping and predictable process stability Manufactured for stability on the lathe, this tool holder combines a compact design with a reliable clamping interface that keeps the insert fixed under varying loads. The modest mass (approx. 0.144 kg) contributes to low overhang inertia while maintaining sufficient rigidity for finishing and semi-finishing passes. The holder is specified with the shank designation J09-F, ensuring compatibility with commonly used boring-bar systems and facilitating straightforward integration into existing tool posts. Practical benefits for workshop efficiency By standardising on a holder that fits the widely used CCMT 09T3 grade, tool change routines are simplified and tool-store complexity is reduced. The concise head dimensions and the 95° incident angle support close-proximity turning and allow economical approach angles without compromising edge life. The straightforward design also makes visual inspection and clamp-screw access fast, helping maintain throughput during shift changes and rapid order fluctuations. Where predictable results and easy handling are priorities, this holder contributes to smoother production flows and less rework. For a reliable Teknik Makina clamping solution and fast delivery from Metav Werkzeuge in Emmerich, request the D426TM holder specification or technical advice by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: D426TM Manufacturer: Teknik Makina Article designation: SCLC for CCMT Indexable Inserts ISO designation: SCLCR 1212 For inserts: CCMT 09T3 Cutting direction: right Overall length: 110 mm Head width: 12 mm Head height: 12 mm Weight: 0.144 kg Cutting angle: 95° Shank designation: J09-F Facts Overall length: 110 mm Head width: 12 mm Head height: 12 mm Weight: 0.144 kg Cutting angle: 95° SKU: D426TM Special features Compatible with CCMT 09T3 inserts ISO SCLCR 1212 holder type Right-hand turning orientation Shank type J09-F Brand: Teknik Makina FAQ Which insert format fits this holder? The holder accepts CCMT 09T3 indexable inserts; the seat geometry matches the CCMT profile to ensure correct clamping and repeatable positioning. Is this holder suitable for finishing or roughing operations? With a 95° cutting angle and a compact 12 mm head, the holder is best suited to finishing and semi-finishing where access and accuracy are required rather than heavy roughing. What is the overall length and how does that affect tool overhang? The overall length is 110 mm, which helps to limit overhang and reduce vibration compared with longer holders, improving stability for fine turning passes. How is the orientation specified? This is a right-hand holder for conventional right-hand turning applications; the designation SCLCR 1212 reflects the ISO geometry and turning side Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SDJC For DCMT 0702 Indexable Inserts, 93° Cutting Angle, SDJCR 1212, K07, For DCMT 0702 Inserts, Innenkühlung, Right-Hand Cutting - Teknik Makina
Take advantage of a compact, ISO‑specified holder that combines rigid clamping with fast insert changes and consistent geometry for stable turning. Order the toolholder directly via Metav Werkzeuge or consult our specialists for application advice. Klemmhalter (SDJC) — SDJCR 1212 right-hand toolholder for DCMT 0702 inserts by Teknik Makina The Klemmhalter (SDJC) is a right-hand turning toolholder designed for external machining with DCMT 0702 indexable inserts, offering a compact 12×12 mm shank and secure Torx clamping. Compact SDJCR 1212 holder, 12×12 mm Right-hand configuration for external turning Accepts DCMT 0702 indexable inserts Torx clamping screw M2.5x5.5 (T8) Consistent clamping for repeatable turning results The holder's ISO designation SDJCR 1212 and 12×12 mm shank deliver a predictable and rigid connection between toolpost and insert, reducing vibration and improving surface finish in production. The clamping system uses a M2.5x5.5 screw operated with a T8 Torx key, which secures the insert firmly and keeps set‑up times short. This fixed geometry supports reproducible positioning of the cutting edge so batch runs maintain tolerance without frequent adjustments. Faster insert changes and optimised cutting posture Compatibility with DCMT 0702 indexable inserts simplifies tooling logistics and allows quick insert replacement without re‑setting the holder. The specified 15 mm cutting height guarantees correct insert alignment for consistent tool engagement, while the 93° cutting angle provides the necessary clearance for typical external turning tasks. Designed as a right‑hand holder, it is optimised for conventional lathe feed directions and delivers reliable chip flow and tool life when matched with appropriate insert grades. Compact reach and straightforward inventory management With an overall length of 125 mm and a cutting‑head width of 16 mm, this holder balances reach and rigidity for confined setups and general turning operations. At approximately 0.13 kg, it is easy to handle during tool changes yet substantial enough to dampen chatter. The holder is identified by SKU D220-1TM and the shank designation K07, simplifying ordering and stock control for workshops and production lines. The robust, standardised specification supports a lean toolroom approach and predictable maintenance intervals. For reliable turning results with Teknik Makina toolholders and tailored tooling recommendations, contact Metav Werkzeuge in Emmerich — eMail: info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: D220-1TM Manufacturer: Teknik Makina ISO designation: SDJCR 1212 Shank designation: K07 Compatible inserts: DCMT 0702 Data Shank width: 12 mm Shank height: 12 mm Cutting head width: 16 mm Cutting height: 15 mm Overall height: 12 mm Overall length: 125 mm Weight: 0.13 kg Cutting angle: 93° Special features Right-hand toolholder Accepts DCMT 0702 indexable inserts Clamping screw M2.5x5.5 (Torx T8) ISO: SDJCR 1212 SKU D220-1TM Manufacturer: Teknik Makina FAQ Which insert size fits this holder? The holder is designed for DCMT 0702 indexable inserts; matching inserts ensure correct cutting geometry and clamping. What is the shank dimension and ISO code? Shank size is 12×12 mm and the holder is specified as SDJCR 1212 for straightforward identification. Which clamping screw and key are required? Clamping uses a M2.5x5.5 screw and a T8 Torx key for secure fastening. Is this holder for left‑hand or right‑hand turning? This is a right‑hand toolholder suitable for standard external turning feeds. How long is the holder and what is the cutting height? Overall length is 125 mm and the cutting height is 15 mm, providing correct insert alignment and reach. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SDJC for DCMT 11T3 Indexable Insert Clamp Holder 93° Right-Hand J11-F-IC, Innenkühlung, SDJCR 1212 - Teknik Makina
Take advantage of a compact, coolant-ready toolholder that secures DCMT 11T3 inserts reliably while delivering stable right-hand turning performance; order the AP571TM directly via Metav Werkzeuge or consult our specialists for application advice. Clamping holder AP571TM — SDJC toolholder for DCMT 11T3 with internal coolant The Clamping holder AP571TM is a right-hand SDJC toolholder designed for use with DCMT 11T3 indexable inserts, offering internal coolant supply and a compact 12 × 12 mm cutting head for stable precision turning. SDJCR 1212 ISO designation Compatible with DCMT 11T3 inserts Internal coolant for improved chip evacuation Robust 12 x 12 mm cutting head dimensions Secure clamping that keeps cutting geometry stable The AP571TM is engineered to maintain consistent cutting geometry during interrupted cuts and heavy finishing passes. The SDJCR 1212 designation corresponds to a proven clamping form that fits standard turning toolholders, while the M3.5x8.5 Torx screw and T15 key provide a secure, repeatable clamp force. This mechanical reliability minimises insert movement and run-out, translating into predictable tool life and a constant surface finish. For workshops aiming to reduce rework and tool-change downtime, this holder supports efficient shopfloor processes through dependable retention and straightforward maintenance. Coolant-fed design for better chip control and tool life Integrated supply channels allow coolant to reach the cutting zone directly, supporting effective chip control and heat dissipation. The internal coolant capability reduces edge temperature and helps prevent built-up edge on the insert, which in turn extends insert life and preserves component tolerances. In applications where surface finish and tool longevity affect production economics, this coolant-ready configuration offers a measurable improvement in machining stability and process reproducibility, especially on medium–heavy duty turning where thermal management matters. Compact dimensions for rigid performance in confined setups With a cutting-head footprint of 12 mm by 12 mm, a cutting height of 32 mm and an overall length of 110 mm, the holder combines rigidity with access to tighter fixtures. The modest mass (0.11 kg) and a 93° cutting angle produce low overhang and reduced vibration, improving chip formation and dimensional control. The right-hand cutting direction specification makes the holder suitable for standard right-hand lathes and CNC turning centres. These compact geometries are particularly beneficial for secondary operations and when tool clearance is limited, enabling more reliable finishes without sacrificing stability. Easy integration and standardised tooling for efficient workflows The toolholder accepts common DCMT 11T3 indexable inserts and mounts on a J11-F-IC shank, simplifying inventory management across tooling systems. The ISO-style designation and conventional fixing hardware mean familiar handling for technicians and fast replacement during tool changes. Standardisation reduces the number of specialised parts required in a busy workshop and streamlines procurement, maintenance and operator training — factors that support continuous, predictable production rhythms. For coolant-ready, compact turning solutions from Teknik Makina, contact Metav Werkzeuge in Emmerich for procurement and technical advice via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: AP571TM Manufacturer: Teknik Makina Article designation: SDJC for DCMT indexable inserts (SDJCR 1212) Facts Cutting-head width: 12 mm Holder height: 12 mm Cutting-head width (alternate): 12 mm Cutting height: 32 mm Overall length: 110 mm Overall height: 12 mm Weight: 0.11 kg Cutting angle: 93° Cutting direction: right-hand Torx screw: M3.5x8.5 Torx key: T15 Shank designation: J11-F-IC Special features Internal coolant: yes Compatible inserts: DCMT 11T3 ISO designation: SDJCR 1212 FAQ What insert type fits this holder? The holder accepts DCMT 11T3 indexable inserts; the AP571TM is specified for this insert form and secures it using the SDJCR-style clamp. Is the holder suitable for coolant-fed machining? Yes. The AP571TM features internal coolant channels to deliver cutting fluid to the insert interface for improved chip evacuation and thermal control. Which cutting direction is supported? This toolholder is configured for right-hand cutting operations and is intended for installation on right-handed turning setups. What are the key mounting and fixing details? Fixing is provided via an M3.5x8.5 Torx screw tightened with a T15 key; shank designation for mounting is J11-F-IC. How does the compact design affect performance? The 12 × 12 mm cutting-head dimensions and 110 mm overall length reduce overhang, increase rigidity and help to lower vibration, resulting in more consistent finishes and longer tool life. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SDJC For DCMT Indexable Inserts 93° Left-Hand SDJCL 1212, K07-F, For DCMT 0702, Innenkühlung, Linksschneidend - Teknik Makina
Reliable clamping for DCMT 0702 inserts combined with a compact 12 × 12 mm cross section ensures stable left‑hand turning with minimal vibration; the 125 mm overall length provides extended reach while the standard Torx M2.5 × 5.5 clamp allows quick insert changes — order via Metav Werkzeuge or consult Metav's technical team if guidance is required. Klemmhalter SDJC for DCMT indexable inserts, left‑hand, 12 × 12 mm (Teknik Makina) Klemmhalter SDJC for DCMT indexable inserts is a left‑hand turning toolholder designed for external turning with DCMT 0702 inserts, offering a compact 12 × 12 mm profile for confined set‑ups. For DCMT 0702 inserts, left‑hand cutting Compact 12 × 12 mm toolholder cross section 125 mm overall length for good reach Torx clamp screw M2.5 × 5.5, T8 key required Precision clamping for repeatable turning results The SDJC clamping geometry is engineered to secure DCMT 0702 inserts with consistent pressure, reducing micro‑movement during interrupted cuts. With a compact 12 × 12 mm cross section and ISO designation SDJCL 1212, the holder provides a stable platform that minimises deflection in light and medium turning applications. The clamping mechanism uses a Torx screw for direct, reliable locking; this standard fastening reduces tool change time and simplifies maintenance while preserving repeatability across batches. Geometry tuned for consistent chip flow and durable edges An approach angle of 93° and a left‑hand orientation create a geometry that separates radial and axial cutting forces, promoting predictable chip flow and more even insert wear. The defined cutting height 15 mm aligns the insert correctly with the tool centre, which supports surface finish stability and reduces the need for corrective passes. For setups that prioritise dimensional control and tool life, the combination of holder angle and insert form delivers measurable process reliability without complex adjustments. Serviceable, workshop‑ready design to reduce downtime Designed for practical workshop use, the holder measures 125 mm overall and weighs 0.14 kg, offering a balance between reach and low rotating mass. The clamp screw specification M2.5 × 5.5 (Torx) and the required T8 key are industry standards, ensuring replacement parts are readily available. Mounting compatibility with bar designation K07‑F and the compact head width of 12 mm make the unit suitable for retrofit into existing toolpost arrangements. Clear, standard features enable quick insert changes and predictable servicing intervals, reducing machine downtime and improving throughput. For application‑specific selection or batch supply of the Teknik Makina SDJC toolholder, contact Metav Werkzeuge's specialists in Emmerich for immediate advice and delivery from stock — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: D154TM Manufacturer: Teknik Makina Article designation: SDJC for DCMT Indexable Inserts ISO designation: SDJCL 1212 Facts Cross section: 12 × 12 mm Head width: 12 mm Cutting height: 15 mm Overall length: 125 mm Weight: 0.14 kg Cutting angle: 93° Cutting direction: left Special features Compatible with DCMT 0702 indexable inserts Clamp screw: M2.5 × 5.5 (Torx) Torx key size: T8 Boring bar designation: K07‑F FAQ Which inserts fit this holder? The holder is specified for DCMT 0702 indexable inserts; the SDJC geometry secures this insert form for reliable external turning. Is the holder for left‑hand or right‑hand turning? This toolholder is a left‑hand version intended for left‑hand turning operations and is identified accordingly in the technical data. What fastener and key are required for the clamp? Clamping uses a Torx screw sized M2.5 × 5.5 and requires a T8 key for safe insertion and removal. What are the critical dimensions for fitting into a toolpost? Key dimensions: cross section 12 × 12 mm, overall length 125 mm, head width 12 mm; ISO designation SDJCL 1212 guides mounting compatibility. How does the 93° cutting angle influence machining? The 93° approach angle shifts the force components to improve stability and chip evacuation, which helps maintain surface quality and extend insert life. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah. 422 Nolu Sokak No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12mm SDJC For DCMT Indexable Inserts 93° SDJCL 1212 K07 For DCMT 0702 Indexable Inserts Innenkühlung Left-Hand Cutting - Teknik Makina
Take advantage of precise left-hand geometry and secure clamping for reliable turning operations; the holder accepts DCMT 0702 inserts and uses a Torx M2.5x5.5 clamping screw for consistent seating. Order the toolholder directly via Metav Werkzeuge or consult our specialists for application advice. SDJC clamp holder for DCMT indexable inserts — left-hand toolholder by Teknik Makina The SDJC clamp holder for DCMT indexable inserts is a left-hand turning toolholder engineered for secure retention of DCMT 0702 inserts in longitudinal and profiling operations. Left-hand design for longitudinal turning Compatible with DCMT 0702 inserts Torx M2.5x5.5 clamping screw, T8 SDJCL 1212 profile, 12 × 12 mm Precision clamping that reduces setup variability The SDJC-style holder delivers secure clamping of DCMT 0702 indexable inserts through a robust Torx M2.5x5.5 screw and a machined pocket that maintains insert seating under cutting loads. This stability reduces rework and minimises vibration, which in turn improves surface finish and extends insert life. For workshops seeking predictable cycle times, the controlled interface between holder and insert translates directly into fewer interventions and steadier part quality. Geometry designed for reliable left-hand turning performance With a left-hand cutting orientation and a defined cutting angle of 93°, the toolholder is tailored for negative-rake DCMT inserts used in facing and longitudinal turning on lathes. The SDJCL 1212 profile (12 × 12 mm) ensures compatibility with standard toolposts and provides a compact footprint while retaining sufficient overhang resistance. For engineers unfamiliar with insert geometry: the 93° angle positions the cutting edge to balance tool life and chip flow, making it suitable for a wide range of steels and general workshop applications. Compact dimensions and serviceable hardware for straightforward maintenance A total length of 125 mm and a cutting-head width of 16 mm give the holder a practical reach without excessive overhang, helping to maintain rigidity in confined setups. The clamping screw uses a common T8 Torx key, which simplifies maintenance and replacement. Because the design favours standardised fixings and dimensions, spare parts management is simplified and downtime is reduced — practical advantages for production environments where tool change frequency impacts throughput. For dependable left-hand turning choose the SDJC clamp holder from Teknik Makina — contact Metav Werkzeuge for supply from Emmerich or request tailored application advice at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical Data SKU: D360-1TM Brand: Teknik Makina ISO designation: SDJCL 1212 Compatible inserts: DCMT 0702 Cutting direction: left Total length: 125 mm Overall height: 12 mm Holder width: 12 mm Cutting head width: 16 mm Cutting height: 15 mm Cutting angle: 93° Clamping screw: M2.5x5.5 Torx T8 Weight: 0.13 kg Facts Total length: 125 mm Holder width: 12 mm Overall height: 12 mm Cutting head width: 16 mm Cutting height: 15 mm Cutting angle: 93° Weight: 0.13 kg Clamping screw: M2.5x5.5 Special features SDJCL 1212 profile Compatible with DCMT 0702 indexable inserts Left-hand turning orientation Torx clamping screw M2.5x5.5, T8 key required Compact, rigid form for reduced vibration FAQ What insert size does this holder accept? The holder accepts DCMT 0702 indexable inserts; the pocket and clamping geometry are matched to that insert size. Is the holder suitable for left-hand turning only? Yes, the tool is designed with a left-hand cutting orientation and is intended for left-hand turning applications. What are the mounting dimensions of the holder? The holder uses an SDJCL 1212 profile with a holder width and height of 12 mm and an overall length of 125 mm. Which screw and key are required for clamping the insert? Clamping is performed with an M2.5x5.5 Torx screw; a T8 Torx key is the correct tool for tightening. How does the 93° cutting angle affect machining? A 93° cutting angle positions the insert to balance cutting forces and chip evacuation, offering versatile performance across common materials and promoting stable cutting with good surface finish. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Precision coolant delivery for demanding turning operations
Tool holders with internal coolant are precision components used in machining, particularly turning, to hold indexable inserts securely and feed them to the workpiece. Also referred to as through-coolant tool holders or internal coolant toolholders, these systems channel coolant directly to the cutting edge to reduce thermal load and improve chip control in heavy or high-speed machining.
How they work and where they help most
Standard holders without internal coolant rely on external nozzles, which can be blocked by chips and fail to reach the insert tip reliably. In contrast, holders with internal coolant contain integrated coolant channels and boreholes in the tool shank that guide the coolant under pressure straight to the insert. This targeted supply is particularly valuable for difficult-to-machine materials, high cutting speeds, deep cuts and internal turning where conventional coolant delivery struggles.
Key facts
| characteristic | detail |
|---|---|
| category | tool holders with internal coolant |
| common synonyms | internal coolant toolholders; coolant-through tool holders |
| typical application | turning, heavy machining, internal bore finishing |
| coolant routing | internal channels and boreholes delivering coolant to the insert seat |
| key technical effect | direct cooling at the cutting edge, improved chip evacuation, reduced thermal load |
| comparison | standard holders use external nozzles; internal coolant holders route coolant through the shank |
Measurable benefits for production
- Direct coolant feed reduces the thermal stress on the insert, extending tool life.
- Improved pressure at the cutting zone enhances chip evacuation, reducing recutting and tool damage.
- More consistent cooling helps achieve better surface finish and dimensional stability.
- Reliable coolant delivery under challenging chip conditions supports higher cutting speeds and heavier cuts.
Metav: precision supply and industrial competence
Metav positions itself as the practical partner for workshops and production: a European quality filter based in Emmerich that combines broad product availability with technical expertise. With over 48,000 customers and more than 250,000 products, Metav supplies through-coolant tool holders and related accessories with dependable logistics and application guidance, making sophisticated cooling solutions accessible for every workshop.
In short
Tool holders with internal coolant deliver targeted, high-efficiency coolant to the insert tip, improving chip control, tool life and surface quality in demanding turning tasks.
FAQ
When should I choose tool holders with internal coolant over standard holders?
Choose tool holders with internal coolant when external coolant nozzles cannot reliably reach the cutting edge, for deep cuts, internal turning, heavy machining or when machining difficult materials at high speeds. The internal coolant toolholders ensure direct cooling and better chip evacuation in these scenarios.
Can internal coolant toolholders be used with all insert types?
Internal coolant toolholders are compatible with most indexable inserts provided the holder and insert interface are specified for coolant-through operation. Verify seat type and manufacturer recommendations for coolant-through compatibility.
What performance improvements can I expect from coolant-through tool holders?
Typical improvements include longer tool life, fewer interruptions from clogged external nozzles, improved chip control and a more consistent surface finish due to reduced thermal distortion at the cutting edge.
How is coolant delivered inside an internal coolant toolholder?
Coolant is channelled through boreholes and internal passages in the tool shank directly to the insert pocket; this focused path creates sufficient pressure at the cutting edge to flush chips away and cool the insert effectively.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com