Turning Tools

Turning Holder (Klemmhalter) from Teknik Makina The Turning Holder MTJNL 2525 is a precision clamping tool for TN-- 2204 indexable inserts, engineered for reliable left-hand turning operations on metalworking lathes. For TN-- 2204 indexable inserts 150 mm overall length for varied setups ISO MTJNL 2525 for secure, repeatable clamping Left-hand cutting with 93° cutting angle 32 mm cutting head width for stable contact Consistent Clamping and Compatibility for Workshop Use Built for repeatable results, the Turning Holder offers a stable platform for TN-- 2204 indexable inserts. Its ISO MTJNL 2525 designation ensures compatibility with common insert geometries, reducing setup time and alignment errors. For users who value uptime, the 150 mm overall length gives flexibility in mounting positions while the 32 mm cutting head width improves insert support, which translates into fewer vibrations and longer Insert Life. Precision Geometry That Boosts Cutting Reliability Thanks to the 93° Cutting Angle and Left-hand Cutting orientation, this holder concentrates cutting forces where the insert seats best, improving surface finish and dimensional control. The defined cut geometry minimizes chatter and simplifies toolpath planning on turning operations. For machinists aiming for consistent tolerances, that focused geometry is a direct contributor to process stability and predictable tool wear. Practical Use Cases and Target Users This clamping tool is designed for shops performing medium-duty turning tasks that require reliable insert retention and easy indexing. Typical applications include component turning, facing, and light profiling where TN-- 2204 inserts are preferred. Small job shops and production lines benefit from reduced setup variance, while maintenance teams appreciate the clear interface between holder and insert for quick replacements. Installation, Handling and a Short Explanation for Newcomers Mounting is straightforward: align the holder to the tool post, secure per machine specifications, and insert the TN-- 2204 indexable insert into the pocket. The ISO code (MTJNL 2525) denotes the holder form and clamping style; it helps you match inserts and toolposts without trial-and-error. Regular inspection of the clamping screw and seat keeps contact surfaces clean and prevents premature wear, ensuring consistent performance over time. Choose Teknik Makina's Turning Holder for dependable left-hand turning and contact METAV Werkzeuge for expert advice and tailored support via info@metav-werkzeuge.com or WhatsApp +49 170 2837271 Technical Data Bezeichnung: Turning Holder Brand: Teknik Makina SKU: D340TM For Indexable Inserts: TN-- 2204 Compatible Inserts: TN-- 2204 Overall Length: 150 mm Weight: 0.775 kg ISO Designation: MTJNL 2525 Secondary Designation: M22 Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Direction: Left Cutting Angle: 93° GTIN: 4061905151187 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Turning Holder from Teknik Makina is designed specifically for TN-- 2204 indexable inserts, ensuring a precise fit when using compatible inserts with the MTJNL 2525 pocket. Is the Teknik Makina Turning Holder suitable for left-hand operations? Yes, the Teknik Makina Turning Holder supports Left-hand Cutting and is configured with a 93° cutting angle to suit left-hand turning applications. How do I maintain the Turning Holder to ensure longevity? Regularly clean the clamping seat and check the clamping screw on the Turning Holder; simple checks prevent deformation and maintain secure insert seating, preserving cutting performance. Can METAV Werkzeuge advise on whether this Turning Holder meets my requirements? If uncertain whether the Turning Holder from Teknik Makina fits specific machining needs, METAV Werkzeuge provides detailed consultation—contact info@metav-werkzeuge.com or call +49 2822 7131930 or WhatsApp +49 170 2837271 for assistance. 150mm MTJNL 2525 Turning Holder for TN-- 2204 Indexable Inserts, 93° Left Cut - Teknik Makina

Turning Holder for Indexable Inserts by Teknik Makina The Turning Holder is designed to securely clamp TN-- 2204 indexable inserts for precision turning tasks on CNC lathes. Compatible with TN-- 2204 indexable inserts Overall length 150 mm for compact setups 25 mm shank width and 25 mm height 32 mm cutting head width for stable clamping 93° cutting angle with right-hand operation Reliable Clamping for Consistent Surface Quality The toolholder delivers stable clamping of TN-- 2204 inserts, which directly improves Surface Finish and Extends Tool Life. Its proven geometry reduces Micro-Vibration during cuts, allowing higher Cutting Parameters without sacrificing Accuracy. For production environments where repeatability matters, this Holder offers predictable results and fewer reworks thanks to its robust clamp design. Rigidity and Design That Withstand Demanding Cuts With a Shank Width of 25 mm and a Cutting Head Width of 32 mm, the Holder provides increased Rigidity that supports heavier feeds and depths of cut. The compact Overall Length of 150 mm helps to minimize Overhang and thus reduces tool deflection. This design advantage leads to more efficient Material Removal and stable chip formation with less spindle load. Engineered Compatibility and Clear Technical Reference The device follows the ISO designation MTJNR 2525, ensuring easy identification when selecting Toolholders and Inserts. The right-hand Cutting Direction and the 93° Cutting Angle are suited for standard external turning operations on conventional and CNC lathes. For users with limited experience: the ISO designation is a common reference that matches Holder geometry to Insert specification, simplifying procurement and machine setup. Fast Setup, Practical Use and Support Mounting and adjustment are straightforward, with a secondary designation of M22 for the clamping interface that aligns with common workshop tooling. This reduces Setup Time and lowers the risk of incorrect fastening. If there is any uncertainty about suitability or integration with a specific lathe, METAV Werkzeuge provides technical advice and application support to ensure the Holder matches your machining requirements. Choose Teknik Makina’s Turning Holder for dependable Precision and durability — for personalized advice contact METAV Werkzeuge at info@metav-werkzeuge.com, +49 2822 7131930 or WhatsApp +49 170 2837271 Technical Data Designation: Turning Holder Brand: Teknik Makina SKU: D202TM Compatible Inserts: TN-- 2204 Overall Length: 150 mm ISO Designation: MTJNR 2525 Secondary Designation: M22 Shank Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Angle: 93° Cutting Direction: Right Weight: 0.775 kg GTIN: 4061905151125 Availability: in Stock Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Turning Holder from Teknik Makina is compatible with TN-- 2204 indexable inserts; the Holder geometry and ISO designation MTJNR 2525 ensure correct seating and reliable clamping for these Inserts. Can the Turning Holder be used for heavy-duty turning? Yes, the Turning Holder’s 25 mm Shank Width and 32 mm Cutting Head Width provide sufficient Rigidity for many demanding external turning tasks, offering stable performance under higher feeds. How do I mount the Teknik Makina Turning Holder on my lathe? Mounting uses the M22 clamping interface specified for this Holder; follow your machine’s tooling guidelines and secure the clamping screw accordingly, or contact METAV Werkzeuge for step-by-step assistance. Is the Turning Holder available for immediate delivery? The Teknik Makina Turning Holder is listed as in Stock; for exact lead times or shipping enquiries, METAV Werkzeuge can provide up-to-date availability and help coordinate delivery. 93° MTJNR 2525 Turning Holder for TN-- 2204, 150 mm Length, M22 — Teknik Makina

Turning Holder — PCLN for CNMG Indexable Inserts Turning Holder by Teknik Makina is a robust toolholder designed to secure CNMG 1204 indexable inserts for precise external turning operations. PCLNR 2525 for CNMG 1204 inserts 150 mm overall length for extended reach Internal coolant for improved chip evacuation 25 x 25 mm shank for stable turning 95° cutting angle for right-hand operations Precision and Rigidity for Accurate Turning Built for shops that demand repeatable results, this clamping tool combines Precision and Rigidity to minimise vibration and tool deflection during cuts. The PCLNR 2525 interface ensures a consistent seat for CNMG 1204 inserts, so each cut maintains dimensional accuracy and surface finish. Operators benefit from reliable clamping force and a geometrically stable setup that supports high-feed and finishing passes without compromising part tolerances. Optimised Cooling and Chip Control for Longer Insert Life Equipped with Internal Coolant, the holder channels cutting fluid directly to the cutting edge, promoting efficient Chip Control and reducing built-up edge on the insert. Enhanced cooling lowers cutting temperatures, which can extend insert life and reduce wear rates. This feature is particularly useful for interrupted cuts or machining tougher steels, where thermal management directly impacts tool performance and process stability. Compact Dimensions that Improve Workshop Productivity The 25 x 25 mm shank and a 32 mm cutting head width deliver a compact, stiff package that fits common turret stations and reduces interference in tight setups. With a 150 mm overall length, the tool offers additional reach for machining deeper features while maintaining a stable cutting stance. These attributes contribute to quicker setup changes and fewer toolholder swaps, making daily shop routines more efficient. Intended Users and Typical Applications Designed for professional turning shops, maintenance workshops and production lines, this holder targets machinists who use CNMG 1204 inserts for medium to heavy turning tasks. The holder’s right-hand 95° cutting orientation and secure fixation make it suitable for external profiling, facing and light roughing operations. Users looking for a dependable toolholder that supports aggressive feeds without sacrificing surface quality will find this solution effective. For precise and dependable turning operations we recommend the Teknik Makina Turning Holder — contact METAV Werkzeuge for dedicated technical support via info@metav-werkzeuge.com or call +49 2822 7131930. Technical Data Bezeichnung: Klemmhalter Marke: Teknik Makina SKU: AP132TM For Indexable Inserts: CNMG 1204 ISO Designation: PCLNR 2525 Designation 2: M12-IKG1/8 Overall Length: 150 mm Shank Width: 25 mm Shank Height: 25 mm Cutting Head Width: 32 mm Cutting Height: 30 mm Cutting Angle: 95° Cutting Direction: Right Internal Coolant: Yes Clamp Screw: TH821 Knee Lever: TL4 Roll Pin: TS-4 Allen Key: 3 Allen Weight: 0.781 kg GTIN: 4061905150296 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit this Turning Holder and who makes it? The Turning Holder by Teknik Makina is designed for CNMG 1204 indexable inserts and provides the PCLNR 2525 mounting interface for secure seating and precise positioning. Does the Turning Holder support coolant-through operation? Yes, the Teknik Makina Turning Holder features internal coolant to direct fluid to the cutting edge, improving chip evacuation and thermal control during machining. What are the key dimensions and who can advise on suitability? The holder has a 150 mm overall length with a 25 x 25 mm shank and a 32 mm cutting head width; for tailored advice on whether this Turning Holder matches your setup, METAV Werkzeuge offers expert consultation at info@metav-werkzeuge.com or +49 2822 7131930. Is the Turning Holder suitable for right-hand turning? Yes, the Teknik Makina Turning Holder is configured for right-hand cutting with a 95° cutting angle, making it suitable for standard external turning tasks. 150mm Turning Holder PCLNR 2525, 95° With Internal Coolant For CNMG 1204 - Teknik Makina

Turning Holder (Klemmhalter) — PCLN for CNMG Indexable Inserts by Teknik Makina The Turning Holder is a robust PCLN tool holder designed for CNMG 1204 indexable inserts, providing secure clamping and reliable performance for left-hand turning operations. Compatible with CNMG 1204 indexable inserts Internal coolant for improved chip evacuation ISO PCLNL 2525 profile for stable clamping 150 mm overall length for standard toolposts Left-hand cutting with 95° cutting angle Precision clamping for consistent machining results A toolholder that delivers repeatable results reduces setup time and scrap. The Turning Holder uses the ISO PCLNL 2525 profile to ensure stable clamping of CNMG 1204 inserts, so the insert seat remains rigid under cutting forces. This design focus translates into more consistent diameters and surface finishes on turned parts, which is particularly valuable for batch production and tight-tolerance workpieces. Improved chip control thanks to internal coolant Internal coolant is integrated to support continuous cutting processes and better thermal control at the cutting edge. By directing coolant through the shank toward the insert pocket, this holder improves chip evacuation and coolant delivery, reducing built-up edge and extending insert life. Workshops that run medium to long cycles will benefit from reduced tool wear and fewer unscheduled tool changes. Standard dimensions for effortless integration into setups With a 150 mm overall length and a 25 x 25 mm shank, the holder fits common toolposts and fixtures without the need for custom adapters. The 32 mm cutting head width and 30 mm cutting height are matched to CNMG 1204 geometry, while the 95° cutting angle and left-hand orientation suit a wide range of turning applications. These standardized dimensions make retrofitting and tool inventory management straightforward. Practical handling and maintenance on the shop floor Installation and routine maintenance are simplified: the clamping screw specification TH821 and the supplied Allen key requirement (3 Allen) make insert changes fast and reliable. Technicians will appreciate the clear access to the clamping elements and the robust mechanical components like the TL4 lever and TS-4 dowel pin, which support repeatable seating and torque behaviour. This holder is engineered for everyday use in demanding machining environments. Highly recommend Teknik Makina’s Turning Holder for workshops seeking durable, coolant-capable holders — contact METAV Werkzeuge for personalised technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Specifications Bezeichnung: Klemmhalter Marke / Hersteller: Teknik Makina SKU: AP142TM For indexable inserts: CNMG 1204 Compatible inserts: CNMG 1204 Overall length: 150 mm Weight: 0.781 kg Allen key: 3 Allen Internal coolant: Yes ISO designation: PCLNL 2525 Secondary designation: M12-IKG1/8 Width: 25 mm Height: 25 mm Cutting head width: 32 mm Clamping screw: TH821 Knee lever: TL4 Cutting direction: left Cutting angle: 95° Cutting height: 30 mm GTIN: 4061905150326 Label: Klemmhalter PCLNL 2525 95° CNMG 1204 Condition: new Availability: in Stock Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina and which sizes are supported? The Turning Holder from Teknik Makina is designed specifically for CNMG 1204 indexable inserts; the holder geometry and pocket dimensions match CNMG 1204 to ensure correct seating and cutting clearance. Does the Teknik Makina Turning Holder provide coolant to the cutting edge? Yes, the Teknik Makina Turning Holder includes internal coolant to improve coolant delivery and chip evacuation, which supports longer insert life and more stable cutting conditions. Which tools are required to change inserts in the Turning Holder? Insert changes and clamping adjustments for the Turning Holder typically require a 3 Allen key for the clamping screw TH821; this makes routine maintenance quick and predictable. Is the Turning Holder suitable for left-hand turning operations? The Turning Holder is configured for left-hand cutting with a 95° cutting angle, making it suitable for applications that require left-direction machining on standard lathes. Who can I contact for further technical details or personalised advice on the Turning Holder? For detailed application support, METAV Werkzeuge offers expert consultation on the Turning Holder by Teknik Makina; contact info@metav-werkzeuge.com, call +49 2822 7131930 or WhatsApp +49 170 2837271. 150mm PCLNL 2525 Turning Holder, 95° Cut Angle, Internal Cooling, For CNMG 1204 Inserts - Teknik Makina

Turning Holder PCLNR 2525 – PCLN Turning Holder for CNMG 1204 Inserts by Teknik Makina The Turning Holder PCLNR 2525 is a right-hand clamping tool for CNMG 1204 indexable inserts, engineered for stable, high-precision turning operations in professional workshops and CNC lathes. Turning Holder PCLNR 2525 for CNMG 1204 inserts Overall length 150 mm for secure reach 95° cutting angle for stable cutting 25 × 25 mm shank for rigid mounting Right-hand cutting direction for turning Consistent clamping for reliable machining results Designed to deliver repeatable performance, this Turning Holder clamps CNMG 1204 inserts securely to minimize vibration and edge deflection. The robust clamping geometry supports stable chip formation and surface finish, which reduces rework and improves cycle-time consistency. For operators, this means fewer adjustments and more predictable output on production runs. Compact dimensions with proven tool geometry With an overall length of 150 mm and a 25 × 25 mm shank, the holder combines compactness with stiffness. The 95° approach angle and 32 mm cutting head width provide a controlled cutting geometry that suits facing and light to medium turning tasks. The ISO code PCLNR 2525 indicates a square shank profile that simplifies fixture selection and ensures compatibility with standard tool posts. Made for professional shops and CNC setups This Turning Holder is intended for machinists, maintenance workshops and small-batch production environments that require dependable indexable tooling. Its design focuses on operational efficiency: fast insert changes with minimal set-up time and compatibility with widely used CNMG 1204 inserts make it suitable for a variety of steels and cast materials. For team workflows, it supports consistent quality across shifts. Practical mounting and compatibility details The clamping screw thread specified as M12 enables secure attachment and easy maintenance. The holder’s right-hand cutting direction matches common lathe configurations and reduces setup errors when replacing tools. Installation follows standard mounting practices for PCLN-type holders: ensure correct seating of the CNMG insert, tighten the clamp screw to the recommended torque, and verify clearance before the first cut. Choose the Teknik Makina Turning Holder PCLNR 2525 for dependable turning performance and contact METAV Werkzeuge for personalized technical advice and support — eMail: info@metav-werkzeuge.com • Phone: +49 2822 7131930 • WhatsApp: +49 170 2837271 Technical Information Designation: Turning Holder Brand: Teknik Makina SKU: P132TM For indexable inserts: CNMG 1204 ISO designation: PCLNR 2525 Overall length: 150 mm Shank width: 25 mm Shank height: 25 mm Cutting head width: 32 mm Cutting height: 30 mm Cutting angle: 95° Cutting direction: right Clamping screw thread: M12 GTIN: 4061905149832 Availability: in Stock Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder PCLNR 2525 from Teknik Makina? The Turning Holder PCLNR 2525 is designed for CNMG 1204 indexable inserts; use inserts sized CNMG 1204 and follow the insert manufacturer’s recommendations for grade and geometry to match the machining task. Can the Teknik Makina Turning Holder PCLNR 2525 be used on CNC lathes? Yes, the Turning Holder PCLNR 2525 is suitable for CNC lathes and manual lathes alike; its 25 × 25 mm shank and standard PCLNR mounting make it compatible with common tool posts and turret systems. How is the CNMG insert secured in the Turning Holder PCLNR 2525? The CNMG 1204 insert is clamped using the holder’s M12 clamping screw; ensure the insert sits flush in the pocket and tighten the screw to the recommended torque to achieve secure, vibration-resistant clamping. Who can provide technical support or further compatibility advice for the Turning Holder PCLNR 2525? METAV Werkzeuge offers expert consultation for the Turning Holder PCLNR 2525 and other Teknik Makina tools — contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored assistance. 95° PCLNR 2525 Turning Holder for CNMG 1204, 150mm - Teknik Makina

Turning Holder PDJNR 2525 for DNMG 1506 inserts by Teknik Makina The Turning Holder is a right-hand toolholder designed for machining with DNMG 1506 indexable inserts, offering internal coolant for stable chip evacuation and precise turning operations. Turning Holder PDJNR 2525 for DNMG 1506 inserts Right-hand orientation with 93° cutting angle Internal coolant for improved chip control 150 mm overall length with 32 mm head width 25 x 25 mm shank for secure clamping Robust construction for steady turning performance This toolholder combines a compact form with durable design elements to ensure consistent results in turning applications. The PDJNR 2525 geometry provides a secure seat for DNMG 1506 indexable inserts, while the 25 x 25 mm shank reduces vibration and improves tool life. One clear advantage is the stable clamping, which translates into improved surface finish and reduced rework for precision parts. Improved chip control and coolant support for longer cycles Engineered with internal coolant, the holder enhances chip evacuation directly at the cutting edge to prevent built-up edge and overheating. The 93° cutting angle and right-hand orientation focus cutting forces to enable predictable tool behavior. For operators this means fewer interruptions for cleaning and more uninterrupted machining time, particularly beneficial on medium-duty turning tasks. Clear compatibility and easy integration in tooling setups Focused on compatibility, the insert seat accepts DNMG 1506 indexable inserts and follows the ISO designation PDJNR 2525, making the unit straightforward to integrate into existing tool turrets and toolrooms. The 150 mm overall length and 32 mm head width balance reach and rigidity, allowing use on various lathes while maintaining accessibility to typical workpiece geometries. Who benefits and where the holder excels Workshops producing turned components with medium to high repeatability gain from the holder’s balance of rigidity and coolant support. The product suits machinists and small to medium batch production environments seeking predictable tool life and consistent part quality. For tailored application advice or assembly recommendations, professional support is available from the dealer network. Strong recommendation: Choose Teknik Makina toolholders for demanding turning tasks and contact METAV Werkzeuge for expert advice at info@metav-werkzeuge.com or +49 2822 7131930 — WhatsApp: +49 170 2837271 Technical specifications Designation: Turning Holder (Klemmhalter) Brand: Teknik Makina SKU: P112TM For indexable inserts: DNMG 1506 Compatible inserts: DNMG 1506 Overall length: 150 mm Weight: 0.73 kg Internal coolant: Yes ISO designation: PDJNR 2525 Secondary designation: M15 Width: 25 mm Height: 25 mm Cutting head width: 32 mm Cutting angle: 93° Cutting direction: Right GTIN: 4061905149764 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Turning Holder by Teknik Makina is designed for DNMG 1506 indexable inserts; the ISO seat PDJNR 2525 ensures secure mounting and correct rake and clearance for standard DNMG formats. Does the Turning Holder support coolant-through operation? Yes, the Turning Holder includes internal coolant to guide coolant to the cutting edge, improving chip control and reducing temperatures during continuous turning cycles. What machining direction is the Teknik Makina Turning Holder intended for? The Teknik Makina Turning Holder is specified for right-hand cutting, with a 93° cutting angle optimized for conventional turning setups. How can I get technical advice or confirm suitability for my lathe? If unsure whether the Turning Holder fits your requirements, METAV Werkzeuge offers competent consultation — contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored support. 150mm Turning Holder PDJN for DNMG Indexable Inserts, 93° Cutting Angle, Right-Hand, PDJNR 2525 - Teknik Makina

Turning Holder (Klemmhalter) by Teknik Makina Turning Holder (Klemmhalter) for secure mounting of DNMG indexable inserts, designed for precise left-hand turning operations in professional workshops. Turning Holder PDJNL 2525 by Teknik Makina Compatible with DNMG 1506 indexable inserts Overall length 150 mm for enhanced rigidity Left-hand cutting with 93° cutting angle Internal coolant for improved chip removal High-precision support for reliable turning results The Turning Holder (Klemmhalter) is engineered to deliver consistent stability during turning tasks. With its ISO designation PDJNL 2525, the toolholder offers a square shank interface that provides reliable clamping and reduced vibration. This stability translates into improved Surface Finish and longer Insert Life when paired with DNMG 1506 indexable inserts, making it suitable for demanding production environments where repeatable accuracy is required. Robust geometry that simplifies setup and handling Designed with a 150 mm Overall Length and a compact Cross-Section, this holder balances reach and stiffness to support a broad range of turning operations. The 32 mm Cutting Head Width and 25 x 25 mm shank dimensions facilitate easy toolpost installation and secure fixation. Users benefit from reduced setup time and a more predictable machining process thanks to the holder’s straightforward mechanical interface. Better chip control and tool life with internal coolant Equipped with Internal Coolant, the holder helps direct cutting fluid close to the cutting edge, which enhances Cooling and Chip Evacuation. For operators unfamiliar with this feature: internal coolant supplies lubricant and coolant through the holder directly to the insert edge, lowering Cutting Temperatures and helping to extend Insert Lifetime. This characteristic is especially useful in continuous production or when working with tougher materials that generate heat. Who benefits from this tool and where to use it Professional machinists and toolroom technicians will find this Turning Holder particularly suitable for medium to heavy-duty turning on lathes that require left-hand cutting. The holder is optimized for DNMG 1506 Inserts—a common, versatile insert geometry—so workshops seeking a reliable, easily serviceable toolholder will find it an efficient choice. For bespoke setups or questions about compatibility, tailored advice is available from METAV Werkzeuge. Secure precise turning performance with Teknik Makina’s Turning Holder — for personalised selection and technical support contact METAV Werkzeuge via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 or WhatsApp: +49 170 2837271 Bezeichnung: Klemmhalter Marke: Teknik Makina SKU: P124TM GTIN: 4061905149795 Passende Wendeplatten: DNMG 1506 ISO Bezeichnung: PDJNL 2525 Bezeichnung 2: M15 Gesamtlänge: 150 mm Breite: 25 mm Höhe: 25 mm Schneidekopf Breite: 32 mm Schneidenhöhe: 38 mm Schnittwinkel: 93° Schnittrichtung: Left Mit Innenkühlung: Yes Gewicht: 0.73 kg Zustand: New Verfügbarkeit: In Stock Hersteller / Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Verantwortliche Person / Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder by Teknik Makina and which versions are compatible? The Turning Holder (Klemmhalter) from Teknik Makina is compatible with DNMG 1506 indexable inserts; this holder is designed for the negative rhombic DNMG geometry commonly used for general turning, enabling straightforward fitment and repeatable clamping. Does the Teknik Makina Turning Holder support coolant-through operation? Yes, the Teknik Makina Turning Holder (Klemmhalter) features internal coolant capability, which directs coolant close to the cutting edge to improve chip evacuation and lower cutting temperatures during machining. Is the PDJNL 2525 designation important when selecting a holder? The PDJNL 2525 ISO designation of this Turning Holder (Klemmhalter) indicates the shank and clamp style; choosing a holder with the correct ISO designation helps ensure secure mounting and compatibility with your toolpost and lathe setup. Who can advise if the Turning Holder from Teknik Makina suits my application? If you are unsure whether the Teknik Makina Turning Holder (Klemmhalter) meets your requirements, METAV Werkzeuge provides expert guidance and can assist with technical details — contact info@metav-werkzeuge.com or call +49 2822 7131930. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#P124TM","sku":"P124TM","mpn":"PDJNL 2525","gtin13":"4061905149795","name":"150mm Turning Holder PDJN for DNMG Indexable Inserts, 93° Left, PDJNL 2525 - Teknik Makina","description":"Turning holder for DNMG 1506 indexable inserts; 150 mm overall length, 25 mm width, 25 mm height, 32 mm cutting head width, internal coolant, 93° cutting angle.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/08/8d/e2/62/62e28d080f56dbb4de4e1288/p119tm-main.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Suitable Inserts","value":"DNMG 1506"},{"@type":"PropertyValue","name":"Overall Length","value":"150 mm"},{"@type":"PropertyValue","name":"Weight","value":"0.73 kg"},{"@type":"PropertyValue","name":"Internal Coolant","value":"yes"},{"@type":"PropertyValue","name":"ISO Designation","value":"PDJNL 2525"},{"@type":"PropertyValue","name":"Shank Designation","value":"M15"},{"@type":"PropertyValue","name":"Width","value":"25 mm"},{"@type":"PropertyValue","name":"Height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting Head Width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting Angle","value":"93°"},{"@type":"PropertyValue","name":"Cutting Direction","value":"left"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"DNMG 1506 indexable inserts fit this holder."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"The overall length is 150 mm."}},{"@type":"Question","name":"Does the holder support internal coolant?","acceptedAnswer":{"@type":"Answer","text":"Yes, the holder features internal coolant."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"The cutting angle is 93°."}},{"@type":"Question","name":"What is the ISO designation?","acceptedAnswer":{"@type":"Answer","text":"ISO designation PDJNL 2525."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-03-31T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder Series"},{"@type":"Thing","name":"Allround Turning Operations"},{"@type":"Thing","name":"Requires DNMG 1506 Inserts"}],"mentions":[{"@type":"Thing","name":"PDJNL 2525"},{"@type":"Thing","name":"Internal Coolant"},{"@type":"Thing","name":"M15 Shank"}]}]}

Turning Holder PDJN for DNMG Indexable Inserts by Teknik Makina The Turning Holder PDJN for DNMG Indexable Inserts is a precision clamping tool designed to secure DNMG 1506 indexable inserts for reliable turning operations in metalworking and industrial workshops. Turning Holder PDJNR 2525 for DNMG 1506 inserts Overall length 150 mm for stable machining Internal coolant for improved chip evacuation 93° cutting angle with right-hand orientation 25 x 25 mm shank with 32 mm cutting head width Precision clamping for consistent machining results The Turning Holder PDJNR 2525 delivers repeatable geometry and machining stability by combining a compact shank with a purpose‑built head for DNMG 1506 inserts. The PDJNR 2525 design ensures secure seating of indexable inserts and reduces vibration, which directly improves surface finish and extends insert life. Operators benefit from predictable tool behaviour during turning, reducing rework and increasing process reliability. Coolant-fed design improves chip control and tool life Equipped with Internal Coolant, this clamping holder channels coolant to the cutting zone to aid chip evacuation and thermal control. By keeping the cutting edge cooler and clearing chips efficiently, the holder supports longer insert life and more consistent cutting forces. The internal coolant feature is particularly advantageous for medium- to high‑speed turning where heat and built-up edge can affect tolerances. Built for workshop versatility and easy setup With a 150 mm overall length and a 25 x 25 mm shank, the holder balances reach and rigidity for diverse shop tasks. The 32 mm cutting head width and 93° cutting angle (right-hand orientation) make the tool suitable for facing and general turning profiles where DNMG 1506 inserts are specified. Quick clamping using the TH825 clamping screw and supplied Allen key helps minimise setup time between tool changes. Compatible components and maintenance guidance Compatibility with DNMG 1506 indexable inserts and the ISO designation PDJNR 2525 simplifies tool selection and inventory management. The holder includes standard accessories such as the TS-4 roll pin and works with the TL4B knee lever for secure fastening. Regular inspection of clamping surfaces and coolant channels preserves performance; blocked coolant passages should be cleared to maintain effective cooling. We recommend Teknik Makina’s Turning Holder PDJNR 2525 for workshops seeking precise, coolant-assisted turning — for tailored advice and support contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Bezeichnung: Turning Holder Marke: Teknik Makina SKU: AP112TM Suitable Inserts: DNMG 1506 ISO Designation: PDJNR 2525 Alternative designation / Part: M15-IKG1/8 Overall length: 150 mm Shank width: 25 mm Shank height: 25 mm Cutting head width: 32 mm Cutting height: 40 mm Cutting angle: 93° Cutting direction: Right Clamping screw: TH825 Knee lever: TL4B Roll pin: TS-4 Allen key: 3 Allen Internal coolant: Yes Tool plate: TA014-1 Weight: 0.759 kg GTIN: 4061905150241 Availability: in Stock Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Turning Holder PDJNR 2525 from Teknik Makina is designed for DNMG 1506 indexable inserts and provides the correct seating and clamping geometry for reliable turning operations with that insert type. Does the Turning Holder have coolant capability? Yes, the Teknik Makina Turning Holder PDJNR 2525 features Internal Coolant to support chip evacuation and thermal control during medium- to high‑speed turning. What are the main dimensions of the Teknik Makina Turning Holder? Key dimensions for the Turning Holder PDJNR 2525 include an overall length of 150 mm, a 25 x 25 mm shank, and a 32 mm cutting head width, which together balance reach and rigidity. Who can I contact for technical advice about the Turning Holder? For technical guidance on the Turning Holder PDJNR 2525 by Teknik Makina, METAV Werkzeuge offers expert consultation — eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271. 93° PDJNR 2525 Turning Holder for DNMG 1506, 150mm, Internal Coolant - Teknik Makina

Turning Holder (Klemmhalter) — PSSNR 2525 for SNMG 1204 by Teknik Makina The Turning Holder (Klemmhalter) is a right-hand toolholder engineered for SNMG 1204 indexable inserts, offering a 45° cutting angle and 150 mm overall length for stable, precise turning operations. PSSNR 2525 ISO designation for secure clamping Compatible with SNMG 1204 indexable inserts 150 mm overall length for stable cutting reach 45° cutting angle for efficient right-hand turning 25 × 25 mm shank: compact, rigid toolholder Precision and stability that reduce rework and cycle time Built to support consistent machining results, the PSSNR 2525 configuration ensures reliable insert retention and repeatable positioning. The 45° rake geometry improves chip flow and reduces cutting forces, which translates into lower vibration and more accurate diameters. As a result, operators achieve tighter tolerances with fewer passes, making this holder especially suitable for production turning where repeatability and surface finish are critical. Optimised for SNMG 1204 indexable inserts to simplify tooling By design, the holder accepts SNMG 1204 indexable inserts, a common size that balances robustness and versatility. SNMG inserts feature four cutting edges per insert, allowing quick indexing when one edge wears. This reduces downtime compared with solid-carbide tooling and lowers operating costs per cutting edge. For users new to indexable tooling, an SNMG insert is a replaceable carbide plate that seats into the pocket of the holder to provide the actual cutting edge. Compact dimensions that increase rigidity and tool life The holder’s 25 mm by 25 mm shank and 32 mm cutting-head width deliver high rigidity at the cutting point, decreasing deflection under load. With an overall length of 150 mm and a mass of approximately 0.742 kg, the toolholder maintains a favourable stiffness-to-reach ratio that helps prevent chatter and prolongs insert life. These dimensional choices are deliberate: greater rigidity means improved surface quality and longer intervals between insert changes. Made for professional workshops and production environments Workshops and small production lines benefit from a toolholder that combines compatibility, stability and simple handling. The design supports efficient tool setup and repeatable mounting, which helps reduce setup time and improves workflow. If you require application-specific guidance—for example feed/speed recommendations or holder orientation—METAV Werkzeuge provides competent technical support to help integrate the holder into your machining process. Strong recommendation: For reliable SNMG 1204 turning applications, choose the Teknik Makina Turning Holder and contact METAV Werkzeuge for tailored technical advice — eMail: info@metav-werkzeuge.com | Phone: +49 2822 7131930 | WhatsApp: +49 170 2837271 Technical Specifications Bezeichnung: Klemmhalter Brand: Teknik Makina SKU: P172TM For Inserts: SNMG 1204 Suitable Inserts: SNMG 1204 ISO Designation: PSSNR 2525 Overall Length: 150 mm Shank Width: 25 mm Shank Height: 25 mm Cutting Head Width: 32 mm Cutting Angle: 45° Cutting Direction: Right Weight: 0.742 kg Condition: new Availability: in Stock GTIN: 4061905052576 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder by Teknik Makina and what is the benefit? The Turning Holder from Teknik Makina is designed for SNMG 1204 indexable inserts; using these inserts gives four cutting edges per insert and fast indexing, which reduces machine downtime and cost per edge. Can the Teknik Makina Turning Holder be used for heavy-duty turning? The Teknik Makina Turning Holder, with a 25 × 25 mm shank and 150 mm length, offers increased rigidity for many demanding turning tasks; for extremely heavy cuts, consider matching insert grade and machine power accordingly. How does the 45° cutting angle affect machining with the Klemmhalter? A 45° cutting angle on the Klemmhalter improves chip evacuation and lowers cutting forces, resulting in smoother surfaces and less tool deflection during right-hand turning. Who can provide technical setup help for the Turning Holder (Klemmhalter)? METAV Werkzeuge offers professional advice for integrating the Turning Holder into your workflow; contact Metav for assistance with speeds, feeds and optimal insert selection. 150mm Turning Holder PSSN for SNMG 1204 Inserts, 45°, PSSNR 2525 - Teknik Makina

Turning Holder (PWLN for WNMG Indexable Inserts) by Teknik Makina The Turning Holder is a precision toolholder designed for turning operations with WNMG 0604 indexable inserts, providing stable clamping and predictable cutting performance. Turning Holder for WNMG 0604 inserts 150 mm total length for extended reach ISO PWLNR 2525 compatible 25 × 25 mm shank for secure clamping 95° cutting angle, right-hand orientation Precision and repeatability for demanding turning tasks This toolholder is engineered to deliver consistent machining results when used with WNMG 0604 inserts. The geometry ensures that the insert sits at the correct rake and clearance angles, so engagement with the workpiece is predictable and stable. For shops that prioritise reproducible surface finish and dimensional accuracy, the holder’s compatibility with the PWLNR 2525 ISO profile reduces setup time and minimizes indexable insert adjustments, allowing faster changeovers and fewer trial cuts. Stable clamping and vibration control for cleaner cuts With a 25 × 25 mm shank and a cutting-head width of 32 mm, the holder provides a rigid interface between machine and insert. The 150 mm overall length balances reach and stiffness to keep chatter low on most standard lathes. A stable clamping system reduces micro-movements during cutting, which helps extend insert life and improves surface quality. This mechanical reliability is particularly beneficial when machining interrupted cuts or heavier feed conditions. Clear guidance for application and compatibility The holder is set up for right-hand turning operations with a 95° cutting angle and is intended specifically for WNMG 0604 indexable inserts. For users less familiar with insert nomenclature: WNMG 0604 denotes a rhombic-shaped carbide insert, 6 mm inscribed circle with a 0.4 mm nose radius, commonly used for general turning and finishing work. Using the correct insert type with this holder ensures correct seat contact and optimal cutting performance without modification. Practical support and workshop integration Manufactured by Teknik Makina and supplied new and in stock, this holder integrates into typical lathe toolposts and clamping systems that accept a 25 mm square shank. If there is uncertainty about suitability for your machine or the intended operation, METAV Werkzeuge offers competent technical advice and can assist with selection and setup. Their team can help match insert grades, cutting parameters and fixturing to your specific application, ensuring the holder performs as expected on your parts. For precision turning applications that demand stable clamping and quick insert changes, choose the Teknik Makina Turning Holder — for personalised technical advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Name: Turning Holder (PWLN for WNMG Indexable Inserts) Manufacturer: Teknik Makina SKU: P161TM For Indexable Inserts: WNMG 0604 Compatible Inserts: WNMG 0604 Total Length: 150 mm Weight: 0.758 kg ISO Designation: PWLNR 2525 Secondary Designation: M06 Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Angle: 95° Cutting Direction: Right GTIN: 4061905052460 Condition: new Availability: in Stock Manufacturer or Manufacturer for English: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person or Responsible Person for English: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Teknik Makina Turning Holder is designed for WNMG 0604 indexable inserts; using WNMG 0604 ensures correct seat engagement and the expected cutting geometry with the PWLN-style pocket. Can this holder be used for left-hand turning? This specific Turning Holder is manufactured for right-hand cutting direction with a 95° cutting angle; left-hand operations would require a correspondingly oriented holder. What shank size and length does the Teknik Makina Turning Holder offer? The holder features a 25 × 25 mm shank and a total length of 150 mm, balancing reach and rigidity for standard lathe toolpost setups. Is technical support available for setup and insert selection? Yes, METAV Werkzeuge provides expert consultation for the Teknik Makina Turning Holder; contact info@metav-werkzeuge.com or call +49 2822 7131930 for application-specific advice. 95° PWLN Turning Holder for WNMG 0604, 150mm, 25×25 mm, PWLNR 2525 - Teknik Makina

Introducing the Turning Holder PWLN for WNMG Indexable Inserts by Teknik Makina The Turning Holder PWLN for WNMG Indexable Inserts secures WNMG 0604 inserts for precision turning tasks across workshops and production environments. PWLNL 2525 ISO Holder design Compatible with WNMG 0604 inserts 150 mm overall length for extended reach 25 x 25 mm shank for stable rigidity 95° cutting angle, left-hand orientation Secure Seating for Accurate Turning The PWLNL 2525 geometry provides a reliable clamping interface for WNMG 0604 indexable inserts, ensuring consistent seating and repeatable results. By keeping the Insert firmly positioned, the Holder reduces micro-movement during cuts, which directly improves Dimension Accuracy and surface quality. This design is particularly advantageous when repeatability and close tolerances are required in serial turning operations. Stable Shank and Reach for Reduced Vibration With a 25 x 25 mm shank and a 150 mm overall length, the toolholder balances reach and stiffness to minimise Vibration while machining. The stable shank cross-section helps maintain tool rigidity, so each cutting pass remains consistent and tool life is supported by lower dynamic loads. The measured Shank dimensions are beneficial for setups that need extended reach without sacrificing stability. Optimised Geometry for Specific Turning Tasks A 95° cutting angle combined with left-hand orientation enables favourable chip flow and clearance for certain turning strategies. For users unfamiliar with indexable inserts: WNMG 0604 denotes an indexable turning insert with a rhombic shape and a 06 size, offering multiple cutting edges that can be rotated or replaced individually. The left-hand configuration suits operations where tool approach and machine spindle direction require that orientation, improving operator planning and fixture layout. Designed for Workshops and Production Environments Teknik Makina engineered this Holder to meet demands of job shops and production lines that process steel and alloy components using indexable tooling. The compact Schneidkopf width of 32 mm and Schneidenhöhe of 30 mm provide compatibility with common toolpost setups and robust engagement during interrupted cuts. Maintenance is straightforward thanks to the standardised ISO designation and readily available replacement inserts. For demanding turning applications, rely on Teknik Makina’s Turning Holder PWLN for WNMG Indexable Inserts — for personalised technical advice contact METAV Werkzeuge at info@metav-werkzeuge.com, call +49 2822 7131930 or WhatsApp +49 170 2837271 Technical Specifications for Confident Selection Bezeichnung: Turning Holder Brand: Teknik Makina SKU: P166TM For Indexable Inserts: WNMG 0604 Compatible Inserts: WNMG 0604 Overall Length: 150 mm Weight: 0.758 kg ISO Designation: PWLNL 2525 Secondary Designation: M06 Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Height: 30 mm Cutting Direction: left Cutting Angle: 95° GTIN: 4061905150005 Availability: in Stock Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Turning Holder by Teknik Makina is designed for WNMG 0604 indexable inserts, and this compatibility ensures straightforward replacement and consistent cutting geometry when using the specified inserts. Is the Turning Holder PWLN suitable for left-hand operations? Yes, the Turning Holder PWLN for WNMG inserts is manufactured with a left-hand cutting orientation, making it suitable for setups and turning strategies that require a left-hand approach. What are the critical dimensions I should check before ordering the Turning Holder? Check the overall length of 150 mm and the shank cross-section of 25 x 25 mm for machine toolholder clearance; these dimensions for the Turning Holder by Teknik Makina determine fit and rigidity in your turret or toolpost. Can METAV Werkzeuge help with technical questions about the Turning Holder? METAV Werkzeuge offers competent advice on the Turning Holder PWLN for WNMG Indexable Inserts; contact them at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 for tailored support. 150mm PWLN Turning Holder for WNMG 0604, 95° Left - Teknik Makina

Turning Holder PWLN for WNMG Indexable Inserts by Teknik Makina The Turning Holder PWLN for WNMG Indexable Inserts is a right-hand clamping tool designed for secure external turning with WNMG 0604 indexable inserts in medium-duty lathe applications. Suitable for WNMG 0604 inserts 150 mm overall length Internal cooling for stable cutting 95° cutting angle for secure clamping ISO PWLNR 2525 compatible Precision and repeatable clamping for consistent cycle times The Turning Holder delivers a stable and repeatable setup that reduces downtime caused by insert adjustments. Its 95° cutting angle and precise clamp geometry ensure the insert sits with minimal runout, which in turn preserves tool life and improves part consistency. For production environments seeking predictable cycle times, this holder offers a straightforward way to lower rework rates and increase first-pass yield. Built-in cooling that supports longer tool life Integrated internal cooling channels provide a controlled coolant flow directly to the cutting edge, helping to manage temperatures and chip evacuation. This targeted coolant delivery reduces heat-related wear on the Insert and allows higher cutting parameters in many materials. The result is extended insert life and fewer tool changes during a shift, improving overall machining efficiency. Compact dimensions that fit tight tool-post setups With a 150 mm overall length, 25 mm width and 25 mm height, the toolholder is engineered to fit compact turret and tool-post arrangements without sacrificing rigidity. The reduced overhang helps minimize vibration and supports stable cutting when working on external diameters. This compact footprint is particularly beneficial in small- to medium-sized lathes or when multiple tools are mounted simultaneously. Compatibility focused on proven insert geometry Designed specifically for WNMG 0604 indexable inserts, this clamping tool aligns with common insert geometries and grades used across a wide range of turning tasks. The ISO designation PWLNR 2525 indicates standardized interface dimensions, simplifying inventory and replacement strategies for workshops that rely on consistent tooling systems. Robust fastening components for secure operation Critical clamping elements such as the TH617 clamp screw, TL3 lever, and TS3 dowel pin provide mechanical security and ease of maintenance. The included 2.5 mm Allen key specification allows for convenient on-machine adjustments, while the solid clamping design reduces the risk of insert movement under load, supporting higher feeds and reliable finishes. Who benefits from this toolholder This turning clamp is aimed at machinists and production engineers who require a dependable, easy-to-service holder for general turning tasks. Workshops focusing on repeatable volume production, prototype shops needing predictable results, and users migrating to standardized insert systems will find the toolholder a practical choice to streamline setups and reduce tooling complexity. For dependable turning performance choose Teknik Makina’s Turning Holder PWLN for WNMG Indexable Inserts — for tailored advice and application support contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Information Bezeichnung: Klemmhalter Marke: Teknik Makina SKU: AP161TM For Indexable Inserts: WNMG 0604 ISO Designation: PWLNR 2525 Designation 2: M06-IKG1/8 Overall Length: 150 mm Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Direction: right Cutting Angle: 95° Internal Cooling: Yes Allen Key: 2.5 Allen Clamp Screw: TH617 Lever: TL3 Dowel Pin: TS3 Insert Seat: TA021 Weight: 0.756 kg GTIN: 4061905150395 Condition: new Availability: in Stock Manufacturer: Teknik Makina Manufacturer for English: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person for English: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder PWLN for WNMG Indexable Inserts by Teknik Makina? The Turning Holder PWLN for WNMG Indexable Inserts from Teknik Makina is designed for WNMG 0604 indexable inserts, ensuring compatibility with commonly stocked grades and geometries used for external turning. Does the Teknik Makina Turning Holder include internal cooling? Yes, the Teknik Makina Turning Holder PWLN for WNMG Indexable Inserts features internal cooling, which directs coolant to the cutting zone to help control temperature and improve chip evacuation. Can this holder be used in compact tool-posts? The Turning Holder PWLN for WNMG Indexable Inserts has a 150 mm overall length and 25 mm cross-section, making it suitable for compact turrets and tool-post setups while maintaining rigidity for stable cutting. What fastening parts are specified for this toolholder by Teknik Makina? Teknik Makina specifies components such as the TH617 clamp screw, TL3 lever and TS3 dowel pin for the Turning Holder PWLN for WNMG Indexable Inserts, and an Allen key size of 2.5 mm is used for adjustments. 95° Turning Holder 150mm for WNMG 0604, Internal Coolant - Teknik Makina

Turning Holder PWLN for WNMG Indexable Inserts from Teknik Makina The Turning Holder PWLN for WNMG indexable inserts secures WNMG 0804 cutting inserts for precise left-hand turning applications on lathes. Turning Holder PWLNL 2525 for WNMG 0804 by Teknik Makina Suitable for WNMG 0804 indexable inserts 25 mm x 25 mm shank for stable clamping 95° cutting angle for left-hand turning 150 mm overall length for secure reach Rigid clamping for consistent machining accuracy The PWLN holder is designed to provide stable clamping and repeatable positioning when using WNMG 0804 inserts, which reduces vibration and improves Surface Finish. The combination of a compact shank and robust head geometry results in high rigidity during interrupted cuts, so workshops benefit from fewer reworks and longer tool life. This makes the holder particularly suitable for precision turning tasks where consistent dimensional accuracy is required. Compact dimensions that increase accessibility and control With a 25 mm x 25 mm shank and 150 mm overall length, the tool reaches into tight setups while maintaining low deflection. The PWLNL 2525 ISO designation denotes the shank format and left-hand orientation, simplifying selection for standard toolposts. A 32 mm cutting-head width gives sufficient support for the indexable insert edge, enabling secure tool seating and controlled chip formation even under moderate cutting forces. Designed for professional workshops and versatile operations This tool holder targets metalworking professionals who require reliable performance with indexable carbide inserts. Its 95° cutting angle and left-hand cut direction are optimised for facing and external turning operations on lathes, offering an effective balance between chip control and tool accessibility. Manufactured by Teknik Makina, the holder integrates into standard tool systems and supports efficient workshop workflows with minimal setup time. We recommend the Turning Holder from Teknik Makina for demanding left-hand turning tasks — for application advice or technical clarifications contact METAV Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 (WhatsApp +49 170 2837271) for expert support. Technical Information Designation: Turning Holder Brand: Teknik Makina SKU: P156TM For Insert: WNMG 0804 ISO Designation: PWLNL 2525 Overall Length: 150 mm Shank Width: 25 mm Shank Height: 25 mm Cutting Head Width: 32 mm Cutting Direction: Left Cutting Angle: 95° Weight: 0.773 kg GTIN: 4061905149931 Availability: In Stock Condition: New Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder by Teknik Makina? The Turning Holder from Teknik Makina is specified for WNMG 0804 indexable inserts, ensuring correct seating and secure clamping for standard WNMG geometry. Is the PWLNL 2525 holder suitable for left-hand operations? Yes, the PWLNL 2525 Turning Holder is designed for left-hand turning, with a 95° orientation optimised for facing and external turning where left-handed cut direction is required. How does the 25 mm x 25 mm shank benefit workshop setups? A 25 mm x 25 mm shank provides a compact footprint with good rigidity, allowing the Turning Holder to access confined setups while maintaining stability during machining. Who can advise if this Turning Holder meets my application needs? METAV Werkzeuge offers competent, hands-on advice for the Turning Holder by Teknik Makina; contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored technical support. 95° PWLN Turning Holder for WNMG 0804, 150mm Length - Teknik Makina

Turning Holder — SCLC for CCMT Indexable Inserts by Teknik Makina Turning Holder SCLC for CCMT Indexable Inserts is a robust clamping tool designed for precision right-hand turning operations with CC-- 09T3 indexable inserts. Fits CC-- 09T3 indexable inserts 150 mm overall length for versatile reach Right-hand orientation with 95° cutting angle SCLCR 2525 shank: 25 × 25 mm compact profile 32 mm cutting head width for stable insert support Compact design for stable, repeatable turning The Turning Holder combines a compact SCLCR 2525 shank with a precisely machined cutting head to deliver repeatable results. Its 25 × 25 mm shank profile reduces vibration and improves tool life by providing a rigid connection to the tool post. Operators benefit from consistent surface finish and dimensional accuracy, particularly on short- to medium-length turning tasks where rigidity impacts final tolerance. Engineered for CC-- 09T3 inserts to maximize performance Designed specifically for CC-- 09T3 indexable inserts, this clamping holder secures the insert with stable geometry, ensuring consistent chip formation and heat dissipation. The 95° cutting angle and 32 mm cutting head width support reliable cutting edge engagement, helping to extend insert life and reduce the frequency of tool changes in production workflows. Practical advantages for workshop applications Thanks to its 150 mm overall length, the holder provides the reach needed for a variety of turning setups without sacrificing stiffness. Its right-hand configuration is suitable for standard lathe turning directions, and the compact form factor allows for close-quarter machining where larger holders would obstruct access. This makes the tool a practical choice for job shops and production lines focusing on repeatable component runs. Clear compatibility and straightforward selection For technicians selecting tooling, the ISO designation SCLCR 2525 clarifies the shank size and type, simplifying toolholder programming and inventory management. The holder’s designation and compatible insert type (CC-- 09T3) make it easy to match with existing tooling systems and to standardize tooling across machines, reducing setup time and minimizing confusion during job changes. Support and guidance for integration into your process If integration into an existing tooling setup raises questions, METAV Werkzeuge offers expert consultation and can advise on suitability, clamping torque recommendations, and optimal insert choices. Professional guidance helps ensure the Turning Holder delivers the expected productivity and surface quality in your specific applications. Strong recommendation: Choose the Teknik Makina Turning Holder for dependable right-hand turning with CC-- 09T3 inserts, and contact METAV Werkzeuge for tailored technical advice — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930, WhatsApp: +49 170 2837271 Bezeichnung: Klemmhalter Brand: Teknik Makina SKU: D403TM Passende Wendeplatten: CC-- 09T3 Gesamtlänge: 150 mm ISO Bezeichnung: SCLCR 2525 Bezeichnung 2: M09 Breite: 25 mm Höhe: 25 mm Schneidekopf Breite: 32 mm Schnittwinkel: 95° Schnitt Richtung: right Gewicht: 0.772 kg GTIN: 4061905153044 Hersteller / Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Verantwortliche Person / Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Turning Holder by Teknik Makina is designed to accept CC-- 09T3 indexable inserts; matching the insert type ensures proper clamping and optimal cutting geometry for stable turning. Is the Turning Holder suitable for long-reach machining? The Turning Holder (SCLCR 2525) offers a 150 mm overall length suitable for many turning tasks, but for extended long-reach applications, Teknik Makina toolholders with larger shank profiles may be preferable. Can METAV Werkzeuge advise on using this Turning Holder in my shop? Yes. METAV Werkzeuge provides expert consultation for the Turning Holder by Teknik Makina, including recommendations on insert selection and setup to ensure the tool meets your production requirements. What is the orientation and cutting angle of the Turning Holder? This Teknik Makina Turning Holder is configured for right-hand turning and features a 95° cutting angle, designed to provide reliable edge engagement and chip control. 150mm SCLCR 2525 Turning Holder for CC-- 09T3 Indexable Inserts, 95° - Teknik Makina

Turning Holder SCLCL 2525 for CC-- 09T3 Indexable Inserts by Teknik Makina Turning Holder SCLCL 2525 — a robust left-hand clamping toolholder engineered for precision turning with CC-- 09T3 indexable inserts in industrial lathes. Suitable for CC-- 09T3 indexable inserts 150 mm overall length for deep reach 25 x 25 mm shank cross-section 32 mm cutting head width for stability 95° cutting angle for accurate profiling Precision build for reliable clamping and repeatable results The Turning Holder SCLCL 2525 combines a compact geometry with solid construction to ensure consistent clamping and minimal vibration during machining. Its 25 x 25 mm shank and widened 32 mm cutting head provide a stable interface between tool and machine, which translates into improved surface finish and longer insert life. Designed for industrial use, the holder supports repeatable setups and reduces downtime in serial production. Designed for demanding left-hand turning applications This clamping holder is optimised for left-hand cutting operations and suits a wide range of turning tasks, from profiling to roughing, when paired with CC-- 09T3 indexable inserts. The combination of the toolholder's geometry and the 95° cutting angle helps maintain cutting forces in favourable directions, enabling precise control over chip flow and part tolerance. Suitable for workshops that require predictable performance under continuous loads. Clear compatibility and practical installation The holder follows the ISO designation SCLCL 2525 and accepts the listed insert type, making integration into existing tooling setups straightforward. With an overall length of 150 mm, the unit offers extended reach while keeping rigidity. The secondary designation M09 and standardised mounting dimensions simplify replacement and inventory management. Simple clamping mechanics allow quick insert changes and reduce set-up times. Expert support and maintenance guidance for longevity Beyond the technical design, the holder benefits from a maintenance-oriented approach: regular inspection of clamping surfaces and correct torque on fastening screws preserve accuracy and safety. For applications requiring tuning—such as special insert grades or non-standard tool angles—professional support is available. METAV Werkzeuge offers competent consultation for selecting the right insert grades and setup parameters to match specific material and cycle requirements. Strong recommendation: choose the Teknik Makina Turning Holder SCLCL 2525 for robust left-hand turning performance — for personalised technical advice and ordering support contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271) Technical data Bezeichnung: Klemmhalter Brand: Teknik Makina SKU: D408TM Compatible Inserts: CC-- 09T3 ISO Designation: SCLCL 2525 Secondary Designation: M09 Overall Length: 150 mm Shank Width: 25 mm Shank Height: 25 mm Cutting Head Width: 32 mm Cutting Angle: 95° Cutting Direction: left Weight: 0.772 kg GTIN: 4061905153112 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder SCLCL 2525 from Teknik Makina? The Turning Holder SCLCL 2525 by Teknik Makina is designed for CC-- 09T3 indexable inserts; using the specified insert type ensures correct seating and reliable performance. Can the Teknik Makina Turning Holder SCLCL 2525 be used for heavy-duty roughing? Yes, the robust 25 x 25 mm shank and widened cutting head of the Teknik Makina Turning Holder SCLCL 2525 provide the rigidity required for many roughing operations, though insert grade and machine power should be matched to the workload. How is the Turning Holder SCLCL 2525 installed and maintained? Installation follows standard clamping procedures for SCLCL holders; ensure proper torque on fastening screws and inspect clamping surfaces regularly to keep the Teknik Makina Turning Holder SCLCL 2525 performing accurately. Who can advise on selecting the right insert grade for the Turning Holder SCLCL 2525? METAV Werkzeuge provides expert consultation for the Teknik Makina Turning Holder SCLCL 2525 and can recommend suitable insert grades and cutting parameters — contact them at info@metav-werkzeuge.com or +49 2822 7131930. 95° SCLCL 2525 Turning Holder for CC-- 09T3, 150mm, left cut - Teknik Makina

Turning Holder SCLCL 2525 for CCMT 1204 Indexable Inserts The Turning Holder SCLCL 2525 is a robust toolholder designed for left-hand turning with CCMT 1204 indexable inserts, offering high rigidity and consistent machining performance in professional turning operations. For CCMT 1204 indexable inserts 150 mm overall length for deep reach Integrated inner cooling for chip control 95° cutting angle for stable machining ISO SCLCL 2525 shank, 25 x 25 mm Precision and Stability for Demanding Turning The Turning Holder SCLCL 2525 combines a rigid ISO SCLCL 2525 shank with a 95° cutting angle to minimise tool deflection and improve surface finish. This structural clarity translates into measurable process benefits: fewer reworks, improved Repeatability and consistent part quality. The holder's geometry supports secure clamping of CCMT 1204 inserts, enabling stable chip formation even under moderate cutting forces. Efficient Cooling and Better Insert Life Built-in inner cooling directs coolant close to the cutting edge, reducing heat concentration and the risk of Built-Up Edge. For the workshop, this means longer insert life and more consistent cycle times without frequently stopping for adjustments. Inner coolant channels also support improved Chip Evacuation, which reduces downtime for manual cleaning during batch production. Straightforward Compatibility and Fast Setup Designed for compatibility with standard CCMT 1204 indexable inserts, the holder features a 25 x 25 mm shank and a 150 mm overall length for increased reach in recessed areas. Installation is simple thanks to standard Torx fastening (Torx key: T15, screw: M4x11) and the compatible U-Plate TA015-1. These widely used interfaces make tool changes predictable and minimise setup time on the machine. Who Benefits and Typical Applications Engineered for professional Workshops and Production Environments, this turning holder excels in left-hand turning tasks where stability and coolant supply are essential. The combination of a sturdy shank, targeted cooling and standardised clamping makes it suitable for serial turning of medium-sized components, particularly where consistent surface quality and process reliability are priorities. Teknik Makina's focus on robust tool design supports repeatable machining results. Choose the robust Turning Holder from Teknik Makina for reliable left-hand turning — METAV Werkzeuge offers expert setup support and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 (WhatsApp: +49 170 2837271). Technical Specifications for Setup and Procurement Designation: Turning Holder (Klemmhalter) Brand: Teknik Makina SKU: AP508TM Compatible Inserts: CCMT 1204 Overall Length: 150 mm Weight: 0.771 kg ISO Designation: SCLCL 2525 Alternate Designation: M12-IK Width (Shank): 25 mm Height (Shank): 25 mm Cutting Head Width: 32 mm Cutting Height: 30 mm Cutting Direction: Left Cutting Angle: 95° Inner Cooling: Yes Torx Key: T15 Torx Screw: M4x11 U-Plate: TA015-1 GTIN: 4061905052187 Availability: In Stock Condition: New Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder SCLCL 2525 from Teknik Makina? The Turning Holder SCLCL 2525 from Teknik Makina is designed to accept CCMT 1204 indexable inserts, using the standard clamping interfaces for secure seating and reliable cutting performance. Does the Turning Holder SCLCL 2525 include coolant supply? Yes, the Turning Holder SCLCL 2525 features inner cooling, which delivers coolant close to the cutting edge to improve chip control and extend insert life. How long is the Turning Holder SCLCL 2525 and is it suitable for recessed turning? The Turning Holder SCLCL 2525 has an overall length of 150 mm, providing additional reach for recessed or deeper turning applications while maintaining shank stability. Who can help with setup or technical questions about the Turning Holder SCLCL 2525? METAV Werkzeuge provides expert advice and support for the Turning Holder SCLCL 2525; contact their technical team at info@metav-werkzeuge.com or call +49 2822 7131930 for personalised assistance. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#AP508TM","sku":"AP508TM","mpn":"AP508TM","gtin13":"4061905052187","name":"150mm SCLCL 2525 95° CCMT 1204 Turning Holder","description":"150mm SCLCL 2525 turning holder for CCMT 1204 indexable inserts; 95° cutting angle, internal coolant, left-hand cut; robust aluminium construction.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/0a/8d/e2/62/62e28d0a0f56dbb4de4e128b/ap505tm-main.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Suitable inserts","value":"CCMT 1204"},{"@type":"PropertyValue","name":"Overall length","value":"150 mm"},{"@type":"PropertyValue","name":"ISO designation","value":"SCLCL 2525"},{"@type":"PropertyValue","name":"Shank size (W x H)","value":"25 x 25 mm"},{"@type":"PropertyValue","name":"Cutting head width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting angle","value":"95°"},{"@type":"PropertyValue","name":"Cutting direction","value":"Left-hand"},{"@type":"PropertyValue","name":"Internal coolant","value":"yes"},{"@type":"PropertyValue","name":"Weight","value":"0.771 kg"},{"@type":"PropertyValue","name":"Torx key","value":"T15"},{"@type":"PropertyValue","name":"Torx screw","value":"M4x11"},{"@type":"PropertyValue","name":"Manufacturer part","value":"M12-IK"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"CCMT 1204 indexable inserts fit this holder."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 150 mm."}},{"@type":"Question","name":"Does it have internal coolant?","acceptedAnswer":{"@type":"Answer","text":"Yes, the holder features internal coolant supply."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"The cutting angle is 95°."}},{"@type":"Question","name":"What is the cutting direction?","acceptedAnswer":{"@type":"Answer","text":"The holder is configured for left-hand cutting."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Manufacturer is Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/150mm-sclcl-2525-95-ccmt-1204","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder"},{"@type":"Thing","name":"Indexable Insert Tooling"},{"@type":"Thing","name":"Lathe Tooling Accessories"}],"mentions":[{"@type":"Thing","name":"Internal coolant"},{"@type":"Thing","name":"SCLCL 2525 ISO designation"},{"@type":"Thing","name":"CCMT 1204 compatible inserts"}]}]}

Turning Holder (Klemmhalter) for CC-- 1204 Inserts by Teknik Makina Turning Holder (Klemmhalter) for secure right-hand turning with indexable inserts in professional workshops. Turning Holder (Klemmhalter) by Teknik Makina SCLCR 2525 shank for stable clamping 150 mm overall length for extended reach 25 x 25 mm shank cross-section for rigidity 95° cutting angle for precise right-hand turning High-precision clamping for consistent turning results The Turning Holder (Klemmhalter) is engineered to deliver consistent machining accuracy by combining a rigid SCLCR 2525 shank with a compact geometry. This configuration reduces vibration and enhances repeatability, so each pass maintains the desired tolerance. For workshops focused on productivity, the stable clamping translates directly into fewer reworks and longer uninterrupted run times. Compact dimensions that improve tool stability and access With an overall length of 150 mm and a shank cross-section of 25 x 25 mm, this clamping tool balances reach and stiffness for medium-duty turning tasks. The 32 mm cutting-head width supports secure seating of the insert while the M12 fixing interface ensures reliable tightening. These dimensions make the holder well suited for setups where both access to tight workpieces and tool rigidity are required. Built for compatibility and practical shop use Designed specifically for CC-- 1204 indexable inserts, the holder supports right-hand cutting operations with a 95° cutting angle that aids in achieving clean profiles and repeatable faces. The product's straightforward interface simplifies insert changes and reduces downtime, making it a practical choice for machinists who use standard indexable inserts across varied turning tasks. Expert support and straightforward integration into production Installation is straightforward: secure the holder with the specified M12 clamp screw and confirm insert seating before cutting. If questions arise about compatibility or setup, METAV Werkzeuge offers detailed advice and technical support to help integrate the holder into existing tool chains. Contact METAV for tailored recommendations or additional technical data to ensure optimal performance. Choose the Teknik Makina Turning Holder for dependable right-hand turning — contact METAV Werkzeuge for expert advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical specifications for setup and ordering Designation: Turning Holder (Klemmhalter) Brand: Teknik Makina SKU: D403-1TM Compatible inserts: CC-- 1204 indexable inserts ISO designation: SCLCR 2525 Secondary designation: M12 Overall length: 150 mm Shank width: 25 mm Shank height: 25 mm Cutting head width: 32 mm Cutting direction: right Cutting angle: 95° Weight: 0.768 kg GTIN: 4061905153068 Availability: in Stock Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts are compatible with the Turning Holder from Teknik Makina? The Turning Holder (Klemmhalter) by Teknik Makina is compatible with CC-- 1204 indexable inserts, ensuring straightforward interchangeability with commonly used turning grades. Is the Turning Holder suitable for right-hand cutting only? Yes, the Teknik Makina Turning Holder (Klemmhalter) is specified for right-hand cutting with a 95° cutting angle, designed to optimise right-hand turning operations. How does the SCLCR 2525 designation affect rigidity and clamping? The SCLCR 2525 designation of the holder indicates the shank geometry and clamping interface; the Teknik Makina Klemmhalter’s SCLCR 2525 shank improves rigidity and stability during medium-duty turning. Who can I contact for installation or compatibility questions about this Turning Holder? For any setup or compatibility questions regarding the Turning Holder (Klemmhalter) by Teknik Makina, METAV Werkzeuge provides expert advice — eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#D403-1TM","sku":"D403-1TM","mpn":"D403-1TM","gtin13":"4061905153068","name":"150mm SCLCR 2525 Turning Holder for CC-- 1204, 95° - Teknik Makina","description":"SCLCR 2525 turning holder for CC-- 1204 indexable inserts; 150 mm length, 95° cutting angle, M12 mount, 25x25 mm shank, 32 mm cutter head width; robust, precise toolholder.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/9d/18/35/64/6435189d79db570c35c6c987/d398tm-main.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/d1/7e/de/62/62de7ed10aced56449540ec3/d398tm-technische-zeichnung.jpg","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/2e/7e/de/62/62de7e2e0aced56449540e8b/d398tm-artikelliste.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Length","value":"150 mm"},{"@type":"PropertyValue","name":"ISO designation","value":"SCLCR 2525"},{"@type":"PropertyValue","name":"For inserts","value":"CC-- 1204"},{"@type":"PropertyValue","name":"Mount thread","value":"M12"},{"@type":"PropertyValue","name":"Shank width","value":"25 mm"},{"@type":"PropertyValue","name":"Shank height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutter head width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting angle","value":"95°"},{"@type":"PropertyValue","name":"Direction","value":"right"},{"@type":"PropertyValue","name":"Weight","value":"0.768 kg"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"Compatible with CC-- 1204 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 150 mm."}},{"@type":"Question","name":"What is the shank size?","acceptedAnswer":{"@type":"Answer","text":"Shank measures 25 mm x 25 mm (SCLCR 2525)."}},{"@type":"Question","name":"What is the cutter head width?","acceptedAnswer":{"@type":"Answer","text":"Cutter head width is 32 mm."}},{"@type":"Question","name":"What is the mounting thread?","acceptedAnswer":{"@type":"Answer","text":"Mounting thread is M12."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle is 95°."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Manufacturer: Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-03-31T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"SCLC for CCMT Indexable Inserts"},{"@type":"Thing","name":"Turning Holder SCLCR 2525"},{"@type":"Thing","name":"Toolholder for precision turning"}],"mentions":[{"@type":"Thing","name":"M12 Mount"},{"@type":"Thing","name":"95° Cutting Angle"},{"@type":"Thing","name":"25x25 mm Shank"}]}]}

Clamp Holder — Turning Holder for CCMT 1204 Indexable Inserts by Teknik Makina The Clamp Holder is a Turning Holder designed for CCMT 1204 indexable inserts, offering secure clamping and right-hand turning for precision metalworking. Clamp Holder SCLCR 2525 for CCMT 1204 inserts Internal coolant for improved chip evacuation 150 mm overall length for stable tool support 95° cutting angle for precise right-hand turning 25 x 25 mm shank with 32 mm cutter head Secure clamping and proven compatibility for indexable inserts The SCLCR 2525 designation ensures direct compatibility with CCMT 1204 indexable inserts, delivering a reliable seating and repeatable positioning that reduces vibration and improves surface finish. Built for quick insert changes, the clamp mechanism secures the cutting edge firmly while allowing uncomplicated maintenance. The presence of internal coolant supports chip evacuation and coolant delivery to the cutting zone, which can extend insert life and stabilise machining results in demanding turning operations. Geometry engineered for accurate right-hand turning With a 95° cutting angle and a cutter head width of 32 mm, this turning holder provides a geometry that promotes consistent tool engagement and dimensional stability. The 150 mm overall length offers balanced overhang for many lathe setups, helping to reduce deflection under load. Designed for right-hand cutting, the toolholder's dimensions (25 mm shank width / 25 mm shank height) make it suitable for standard tool posts and clamping systems used in professional workshops that prioritise precise, repeatable turning operations. Practical assembly and workshop efficiency Assembly and service are straightforward thanks to industry-standard fastenings such as the Torx T15 interface and the supplied M4x11 Torx screw; the designated U-Plate TA015-1 simplifies mounting and alignment. These features minimise setup time and downtime, making the holder a pragmatic choice for machine shops that require dependable changeover routines. Suited to skilled machinists and production environments, the holder helps maintain throughput while reducing the complexity of insert handling and coolant routing. Choose Teknik Makina’s Clamp Holder for consistent, production-grade turning — for expert advice or to confirm fitment, contact METAV Werkzeuge by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Technical Specifications for Workshop Planning Designation: Clamp Holder Brand: Teknik Makina SKU: AP503TM For Indexable Inserts: CCMT 1204 ISO Designation: SCLCR 2525 Overall Length: 150 mm Shank Width: 25 mm Shank Height: 25 mm Cutter Head Width: 32 mm Cutting Height: 30 mm Cutting Direction: right (right-hand turning) Cutting Angle: 95° Internal Coolant: Yes Torx Key: T15 Torx Screw: M4x11 U-Plate: TA015-1 Weight: 0.771 kg GTIN: 4061905052651 Availability: in Stock Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts are compatible with the Clamp Holder from Teknik Makina? The Clamp Holder from Teknik Makina is designed specifically for CCMT 1204 indexable inserts; the ISO designation SCLCR 2525 ensures correct seating and alignment for these insert types. Does the Teknik Makina Clamp Holder support internal coolant? Yes, the Teknik Makina Clamp Holder features internal coolant, which aids chip evacuation and cooling directly at the cutting edge when connected to the machine's coolant supply. Is the Clamp Holder suitable for right-hand turning only? The Clamp Holder is configured for right-hand cutting, providing optimized geometry and a 95° cutting angle for standard right-hand turning operations. How can I get help choosing the right turning holder for my machine? If you are unsure whether the Teknik Makina Clamp Holder fits your setup, METAV Werkzeuge offers expert consultation—contact info@metav-werkzeuge.com, call +49 2822 7131930, or message via WhatsApp at +49 170 2837271 for personalised assistance. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#AP503TM","sku":"AP503TM","mpn":"AP503TM","gtin13":"4061905052651","name":"150mm SCLCR 2525 Turning Holder for CCMT 1204, 95° cutting angle - Teknik Makina","description":"150mm SCLCR 2525 turning holder for CCMT 1204 indexable inserts; internal coolant, 95° cutting angle, suitable for right-hand cutting.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/0a/8d/e2/62/62e28d0a33927e49dbf377eb/ap500tm-main.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Length","value":"150 mm"},{"@type":"PropertyValue","name":"ISO designation","value":"SCLCR 2525"},{"@type":"PropertyValue","name":"For inserts","value":"CCMT 1204"},{"@type":"PropertyValue","name":"Insert designation 2","value":"M12-IK"},{"@type":"PropertyValue","name":"Width","value":"25 mm"},{"@type":"PropertyValue","name":"Height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting head width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting angle","value":"95°"},{"@type":"PropertyValue","name":"Weight","value":"0.771 kg"},{"@type":"PropertyValue","name":"Coolant","value":"internal"},{"@type":"PropertyValue","name":"Cutting direction","value":"right"},{"@type":"PropertyValue","name":"Torx key","value":"T15"},{"@type":"PropertyValue","name":"Torx screw","value":"M4x11"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What length is the turning holder?","acceptedAnswer":{"@type":"Answer","text":"The turning holder has a total length of 150 mm."}},{"@type":"Question","name":"Which inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"Designed for CCMT 1204 indexable inserts."}},{"@type":"Question","name":"What is the ISO designation?","acceptedAnswer":{"@type":"Answer","text":"ISO designation SCLCR 2525."}},{"@type":"Question","name":"Does the holder support internal coolant?","acceptedAnswer":{"@type":"Answer","text":"Yes, the holder features internal coolant."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle is 95° for right-hand cutting."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"SCLC for CCMT Indexable Inserts"},{"@type":"Thing","name":"Turning Holder SCLCR 2525"},{"@type":"Thing","name":"Teknik Makina tooling"}],"mentions":[{"@type":"Thing","name":"Internal coolant"},{"@type":"Thing","name":"CCMT 1204 inserts"},{"@type":"Thing","name":"95° cutting angle"}]}]}

Turning Holder SDHC for DCMT Indexable Inserts by Teknik Makina The Turning Holder SDHC for DCMT Indexable Inserts is a precision clamping solution for turning applications, designed to secure DCMT 11T3 indexable inserts for reliable metalcutting operations. Teknik Makina Turning Holder SDHCR 2525 for DCMT 11T3 Secure clamping with robust SDHC design 150 mm overall length for standard toolposts Right-hand cutting with 107.5° cutting angle Compact head width 32 mm for versatile access Durable clamping and consistent cutting performance Built for repeatable results, this Turning Holder features the SDHCR 2525 ISO design that delivers stable insert seating and reduced vibration. The holder’s construction supports consistent chip flow and improved surface finish, making it suitable for serial turning tasks. With a focus on repeatability, the design reduces setup times and minimises downtime, ensuring efficient machining across batches. Compatibility with DCMT 11T3 inserts for flexible tooling Engineered specifically for DCMT 11T3 indexable inserts, the holder enables quick insert changes and secure fixation. This compatibility simplifies tooling logistics and allows workshops to use a common insert family across multiple operations. The targeted fit helps maintain cutting geometry and prolongs insert life by ensuring correct seating and pressure distribution during cutting. Compact dimensions for better accessibility and tool life The holder’s compact head width of 32 mm and a tool body of 25 mm x 25 mm allow access to confined areas while maintaining rigidity. Reduced overhang and a 150 mm overall length lower bending moments and extend tool and insert life. For operations where reach and stiffness must be balanced, this design offers improved stability without sacrificing access to tight workpiece features. Designed for workshop reliability and simple integration Manufactured by Teknik Makina, the holder is built to integrate smoothly into standard toolposts and setups. The right-hand cutting orientation and a precise 107.5° cutting angle deliver predictable chip control and repeatable results on common turning materials. For maintenance and replacement planning, the clear ISO designation and robust mounting geometry simplify inventory and procurement. Choose Teknik Makina’s Turning Holder for dependable clamping of DCMT inserts — for expert advice or technical clarification contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Technical Specifications for reliable clamping Bezeichnung: Turning Holder Brand: Teknik Makina SKU: D252TM For Indexable Inserts: DCMT 11T3 Compatible Inserts: DCMT 11T3 Overall Length: 150 mm Weight: 0.738 kg ISO Designation: SDHCR 2525 Secondary Designation: M11 Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Direction: Right Cutting Angle: 107.5° GTIN: 4061905153495 Condition: New Availability: In Stock Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts does the Turning Holder from Teknik Makina accept? The Teknik Makina Turning Holder is designed to accept DCMT 11T3 indexable inserts, ensuring a secure fit and correct cutting geometry for standard turning operations. Is the Turning Holder SDHCR 2525 suitable for right-hand turning only? Yes, the Teknik Makina Turning Holder SDHCR 2525 shown here is specified for right-hand cutting, which aligns with common turning setups that require that orientation. Can the Turning Holder be used in compact toolposts and confined spaces? The compact dimensions and 32 mm cutting head width of the Teknik Makina Turning Holder make it well suited for installations where accessibility and rigidity are both required. Who can I contact for technical questions about the Turning Holder? For technical questions about the Teknik Makina Turning Holder, METAV Werkzeuge offers expert advice — eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271. 150mm SDHC Turning Holder for DCMT 11T3 Indexable Inserts, SDHCR 2525, 107.5° - Teknik Makina

Turning Holder (SDHCL 2525) for DCMT 11T3 Inserts — Teknik Makina The Turning Holder is a robust toolholder designed to securely clamp DCMT 11T3 indexable inserts for precise left-hand turning operations in metalworking. SDHCL 2525 for DCMT 11T3 inserts 150 mm overall length for deep reach 25 mm shank width and height 107.5° cutting angle for stable cuts Left-hand cutting direction Consistent Rigidity and Repeatability for Accurate Turning The Turning Holder delivers Rigidity that reduces vibration and improves Surface Finish when machining a variety of materials. The clamping concept ensures repeatable insert positioning so that tool paths remain stable cycle after cycle. For users seeking measurable improvements in tool life and part quality, this Holder provides a straightforward way to raise Process Reliability without changing machine settings. Clear Dimensions and Direct Compatibility to Save Setup Time With an Overall Length of 150 mm and a Shank of 25 mm x 25 mm, the holder fits common toolpost mounts and enables access to deeper workpieces. The Schneidkopf Width of 32 mm and ISO designation SDHCL 2525 make it compatible with DCMT 11T3 indexable inserts, simplifying procurement and changeover. For those new to insert coding: DCMT denotes a diamond-shaped insert with specific rake and clearance characteristics, chosen here for universal turning tasks. Geometry Designed for Efficient Cutting and Chip Control The Holder’s 107.5° Cutting Angle and Left-Hand cutting direction concentrate cutting forces to the clamped Insert, promoting stable cutting and predictable chip flow. This geometry helps reduce deflection during interrupted cuts and supports consistent surface tolerance. Operators benefit from fewer reworks and more predictable tool-change intervals, improving overall Shop Floor Throughput with minimal process adjustment. Who Benefits and Where to Get Expert Advice Precision Workshops, Job Shops and Maintenance Departments that require reliable, repeatable turning operations will find this Holder especially useful. Installation and selection are straightforward, yet technical choices such as Insert Grade or Cutting Conditions can impact results. METAV Werkzeuge offers extensive and competent advice for tool selection and application support; expert help is available if further technical data or compatibility checks are needed. We recommend Teknik Makina’s Turning Holder SDHCL 2525 for reliable, precision turning — for personalised advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930. Designation: Turning Holder (Klemmhalter) Brand: Teknik Makina SKU: D352TM Compatible Inserts: DCMT 11T3 ISO Designation: SDHCL 2525 Overall Length: 150 mm Shank Width: 25 mm Shank Height: 25 mm Cutting Head Width: 32 mm Cutting Angle: 107.5° Cutting Direction: Left Weight: 0.738 kg GTIN: 4061905153518 Availability: In Stock Condition: New Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina and which designation should I order? The Turning Holder from Teknik Makina is designed for DCMT 11T3 indexable inserts; order inserts matching the DCMT 11T3 geometry to ensure correct fit and cutting performance with the SDHCL 2525 clamp. Can the Turning Holder SDHCL 2525 be mounted on my existing toolpost? The SDHCL 2525 Turning Holder has a Shank of 25 mm x 25 mm and an Overall Length of 150 mm, so it fits standard toolpost systems that accept a 25 mm shank; confirm your toolpost clamping dimensions or contact METAV Werkzeuge for compatibility checks. How does the 107.5° cutting angle affect machining with the Teknik Makina Turning Holder? The 107.5° cutting angle concentrates cutting forces to the Insert and Holder interface, improving stability and chip control during turning; this leads to more consistent surface quality and extended Insert life under comparable cutting conditions. 150mm SDHCL 2525 Turning Holder for DCMT 11T3 Indexable Inserts, 107.5° - Teknik Makina

Clamping Holder — Turning Holder for DCMT Indexable Inserts by Teknik Makina The Clamping Holder is a precision turning holder designed for DCMT 11T3 indexable inserts, optimised for right-hand external turning and stable metalcutting setups. SDJCR 2525 ISO design for secure clamping Compatible with DCMT 11T3 indexable inserts 150 mm overall length for rigid setups 25 x 25 mm shank for compact toolposts 93° cutting angle for consistent chip control Built for secure, repeatable clamping and longer Insert Life The holder's SDJCR 2525 ISO configuration ensures a firm, repeatable seat for DCMT 11T3 inserts, which directly improves process stability and reduces insert wear. By keeping the Insert position constant, cutting forces remain predictable and finishing quality becomes more consistent. For workshops running small to medium turning batches, this repeatability translates into fewer tool changes and more uptime. Compact dimensions that increase Rigidity and control With an overall length of 150 mm and a shank of 25 mm x 25 mm, the design minimises overhang while providing a robust connection to the toolpost. The 32 mm cutting-head width balances accessibility and support for the Insert, improving heat dissipation and lowering vibration during cuts. These dimensional properties make setup straightforward and help maintain surface finish under typical external turning loads. Designed for straightforward integration into turning setups The holder is configured for right-hand cutting with a 93° cutting angle, giving predictable chip direction and reliable clearance for general turning tasks. The alternative designation M11 indicates the specified mounting/connection interface used for secure fixation in compatible toolholders. Together, these features allow rapid tool changes and simple calibration, so setups remain efficient without compromise to precision. Who benefits and how to apply the holder effectively Workshops, CNC turning centres and maintenance departments that use indexable tooling will find this holder particularly useful when a compact, rigid turning tool is required. Installation is practical for routine external turning and for jobs where predictable chip control matters. For best results, pair the holder with recommended DCMT 11T3 grades tuned to the workpiece material and verify clamping torque to maintain consistent performance. Choose Teknik Makina’s Clamping Holder for reliable, repeatable turning — METAV Werkzeuge offers expert technical advice and personalised support: eMail info@metav-werkzeuge.com • Phone +49 2822 7131930 • WhatsApp +49 170 2837271 Technical specifications for setup and compatibility Bezeichnung: Clamping Holder Marke: Teknik Makina SKU: D228TM For indexable inserts: DCMT 11T3 ISO designation: SDJCR 2525 Secondary designation: M11 Overall length: 150 mm Shank width: 25 mm Shank height: 25 mm Cutting-head width: 32 mm Cutting direction: Right Cutting angle: 93° Weight: 0.735 kg GTIN: 4061905153273 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Clamping Holder from Teknik Makina? The Teknik Makina Clamping Holder is designed for DCMT 11T3 indexable inserts; using the specified insert type ensures correct seating and optimal cutting performance. Is the Clamping Holder suitable for right-hand turning only? Yes, this Clamping Holder is configured for right-hand cutting and a 93° cutting angle, making it suitable for standard external turning applications that require that orientation. How does the SDJCR 2525 designation affect compatibility? The SDJCR 2525 ISO designation defines the holder geometry and clamping method; matching this holder with corresponding toolposts and DCMT 11T3 inserts guarantees proper fit and repeatability. Can METAV Werkzeuge advise on choosing the right insert grade? Absolutely — METAV Werkzeuge provides competent consultation for selecting insert grades and setup parameters to match your machining task; contact info@metav-werkzeuge.com or call +49 2822 7131930 for personalised support. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#D228TM","sku":"D228TM","mpn":"D228TM","gtin13":"4061905153273","name":"Turning Holder SDJCR 2525 93° for DCMT 11T3, 150 mm - Teknik Makina","description":"Turning holder for DCMT 11T3 indexable inserts; ISO SDJCR 2525; overall length 150 mm; right-hand cut; robust 25x25 mm shank.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/15/14/35/64/64351415e3692e16d2a37e9e/d220tm-main.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/2d/7e/de/62/62de7e2d33927e49dbf32731/d220tm-artikelliste.jpg","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/d0/7e/de/62/62de7ed00aced56449540ec0/d220tm-technische-zeichnung.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"For indexable inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"ISO designation","value":"SDJCR 2525"},{"@type":"PropertyValue","name":"Overall length","value":"150 mm"},{"@type":"PropertyValue","name":"Shank width","value":"25 mm"},{"@type":"PropertyValue","name":"Shank height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting head width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting height","value":"30 mm"},{"@type":"PropertyValue","name":"Cutting direction","value":"right"},{"@type":"PropertyValue","name":"Cutting angle","value":"93°"},{"@type":"PropertyValue","name":"Weight","value":"0.735 kg"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"Designed for DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 150 mm."}},{"@type":"Question","name":"What is the ISO designation?","acceptedAnswer":{"@type":"Answer","text":"ISO designation SDJCR 2525."}},{"@type":"Question","name":"What are the shank dimensions?","acceptedAnswer":{"@type":"Answer","text":"Shank width 25 mm and shank height 25 mm."}},{"@type":"Question","name":"What cutting angle does it have?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle 93°; right-hand cutting direction."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Manufacturer Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder"},{"@type":"Thing","name":"DCMT 11T3 Compatibility"},{"@type":"Thing","name":"SDJCR 2525 ISO Standard"}],"mentions":[{"@type":"Thing","name":"25x25 mm shank"},{"@type":"Thing","name":"150 mm overall length"},{"@type":"Thing","name":"93° cutting angle"}]}]}

Turning Holder SDJCL 2525 for DCMT 11T3 Indexable Inserts by Teknik Makina The Turning Holder SDJCL 2525 is a robust lathe tool holder designed for precise left‑hand turning with DCMT 11T3 indexable inserts, suitable for professional workshop use and production environments. Compatible with DCMT 11T3 indexable inserts 150 mm overall length for stable tool overhang Internal Coolant for improved chip evacuation Secure clamping with Torx T15 and M3.5x11 screws 93° cutting angle for reliable left‑hand turning Precision and Compatibility that Reduce Set‑up Time The SDJCL 2525 holder has been engineered to accept DCMT 11T3 indexable inserts, enabling quick insert changes and consistent cutting geometry. By matching the insert pocket precisely, the holder minimizes runout and vibration, which leads to more predictable surface finish and longer insert life. For users unfamiliar with insert codes: DCMT denotes a double‑sided, rhombic insert type with a 55° diamond shape; this holder ensures correct seating and orientation so the tool performs as intended without repeated adjustments. Practical Workshop Features for Reliable Operation With a 150 mm overall length and a 93° cutting angle for left‑hand operations, this holder balances accessibility and rigidity to support stable turning. The Internal Coolant channel directs fluid close to the cutting edge, helping to control temperature and chip flow while reducing thermal wear on the insert. Clamping and maintenance are simplified by the Torx T15 drive and M3.5x11 screws, which provide reproducible torque and secure fixation—advantages that reduce downtime during tool changes in busy shop environments. Who Benefits and How to Integrate It into Your Process Machinists and production technicians who require repeatable left‑hand turning will find this turning holder especially useful. Its 25 mm width and 25 mm height make it compatible with standard toolposts for small to medium turning applications, while the 32 mm Schneidkopf (cutting‑head) width offers a stable seat for the insert. When integrating the holder, confirm insert type DCMT 11T3 and the left‑hand orientation; correct pairing yields consistent cutting forces and predictable chip control. For assistance selecting the right holder for a specific machine or application, expert support is available. For workshops seeking durable, production‑ready tooling we recommend the Teknik Makina Turning Holder SDJCL 2525 — for tailored advice and ordering assistance contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271). Technical Details Turning Holder Brand: Teknik Makina SKU: AP517TM Compatible Inserts: DCMT 11T3 ISO Designation: SDJCL 2525 Overall Length: 150 mm Width: 25 mm Height: 25 mm Cutting‑head Width: 32 mm Cutting Angle: 93° Cutting Direction: Left Internal Coolant: Yes Torx Key: T15 Torx Screw: M3.5x11 U Plate: TA030 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ Which inserts fit the Turning Holder SDJCL 2525 from Teknik Makina? The Turning Holder SDJCL 2525 by Teknik Makina is designed for DCMT 11T3 indexable inserts; pairing this holder with the specified insert type ensures correct seating, cutting geometry and optimal performance. Does the Teknik Makina Turning Holder SDJCL 2525 support internal coolant? Yes, the Teknik Makina Turning Holder SDJCL 2525 features Internal Coolant, which channels fluid to the cutting zone to improve chip evacuation and reduce thermal loading on the insert. Is the Turning Holder SDJCL 2525 suitable for left‑hand turning only? The SDJCL 2525 turning holder is configured for left‑hand cutting direction as specified by Teknik Makina; for right‑hand operations a corresponding right‑hand holder should be chosen. How do I secure the insert and perform maintenance on the Teknik Makina Turning Holder SDJCL 2525? Clamping is accomplished using the Torx T15 interface and M3.5x11 screws supplied; regular checks of screw torque and coolant channels will keep the Turning Holder SDJCL 2525 operating reliably—METAV Werkzeuge can advise on torque settings and maintenance routines if needed. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#AP517TM","sku":"AP517TM","mpn":"AP517TM","gtin13":"4061905052248","name":"150mm SDJCL 2525 93° SDJC for DCMT Indexable Inserts","description":"SDJC turning holder for DCMT 11T3 indexable inserts, 150 mm overall length, coolant-through, left cutting, robust construction by Teknik Makina.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/09/8d/e2/62/62e28d0933927e49dbf377ea/ap515tm-main.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Compatible inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Overall length","value":"150 mm"},{"@type":"PropertyValue","name":"Weight","value":"0.735 kg"},{"@type":"PropertyValue","name":"ISO designation","value":"SDJCL 2525"},{"@type":"PropertyValue","name":"Shank designation","value":"M11"},{"@type":"PropertyValue","name":"Width","value":"25 mm"},{"@type":"PropertyValue","name":"Height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting head width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting angle","value":"93°"},{"@type":"PropertyValue","name":"Coolant-through","value":"yes"},{"@type":"PropertyValue","name":"Cutting direction","value":"left"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Which inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"150 mm overall length."}},{"@type":"Question","name":"Does it support coolant-through?","acceptedAnswer":{"@type":"Answer","text":"Yes, the holder is coolant-through."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle 93°."}},{"@type":"Question","name":"Is the cutting direction left or right?","acceptedAnswer":{"@type":"Answer","text":"Left cutting direction."}},{"@type":"Question","name":"What is the ISO designation?","acceptedAnswer":{"@type":"Answer","text":"ISO designation SDJCL 2525."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder"},{"@type":"Thing","name":"SDJC for DCMT Indexable Inserts"},{"@type":"Thing","name":"Coolant-through tooling"}],"mentions":[{"@type":"Thing","name":"Teknik Makina"}]}]}

Turning Holder SDJC for DCMT 11T3 Indexable Inserts by Teknik Makina The Turning Holder is a robust toolholder for left-hand turning, engineered to securely carry DCMT 11T3 indexable inserts in demanding metalcutting applications. Turning Holder for DCMT 11T3 indexable inserts 150 mm overall length for stable support 93° cutting angle for reliable chip control 32 mm cutting head width for robust performance Left-hand cutting, ISO SDJCL 2525 designation Maximised Stability for Precise Turning Results Heavy-duty construction delivers stability where it matters: the holder’s 150 mm overall length and 32 mm cutting head width reduce deflection during engaging cuts. This increases process reliability and allows operators to maintain consistent surface finishes with fewer interruptions. The design focuses on one clear benefit — higher part quality through reduced tool vibration. Engineered Compatibility and Clear Setup Benefits Designed specifically for DCMT 11T3 indexable inserts, the toolholder simplifies setup and reduces guessing during insert changes. The ISO designation SDJCL 2525 ensures predictable clamping geometry and repeatable seating, so fitting an insert is straightforward even in fast-paced production. For machinists, this means shorter set-up times and fewer alignment adjustments per batch. Optimised Cutting Geometry for Controlled Chip Flow A 93° cutting angle contributes to chip control and effective heat distribution at the cutting edge, especially for left-hand turning operations. That geometry helps maintain tool life under cyclic loads and supports smoother feeds on a range of materials. For processes requiring consistent chip evacuation, this feature translates into fewer stoppages and improved cycle stability. Who Benefits from This Toolholder Workshops and manufacturers focusing on turning operations with indexable inserts will find the holder particularly suited to small- and medium-batch production where tool reliability and speed matter. The toolholder is appropriate for skilled operators and production teams seeking predictable tool behaviour and straightforward compatibility with DCMT 11T3 inserts. We recommend the Teknik Makina Turning Holder for precision left-hand turning; contact METAV Werkzeuge for personalised advice and implementation support — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930, WhatsApp: +49 170 2837271 Designation: Turning Holder Brand: Teknik Makina SKU: D368TM Compatible Inserts: DCMT 11T3 Overall Length: 150 mm Weight: 0.735 kg ISO Designation: SDJCL 2525 Secondary Designation: SDJC for DCMT Indexable Inserts Shank Width: 25 mm Shank Height: 25 mm Cutting Head Width: 32 mm Cutting Height: 30 mm Cutting Direction: Left Cutting Angle: 93° GTIN: 4061905153327 Availability: in Stock Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts are compatible with the Turning Holder from Teknik Makina? The Turning Holder from Teknik Makina is compatible with DCMT 11T3 indexable inserts; the holder’s geometry and the ISO designation SDJCL 2525 ensure secure seating and repeatable clamping for these inserts. Can the Teknik Makina Turning Holder be used for right-hand operations? The Teknik Makina Turning Holder is specified for left-hand cutting direction; for right-hand applications, please consult METAV Werkzeuge to verify alternative holders or configurations suitable for right-hand turning. How does the 93° cutting angle benefit machining with the Teknik Makina Turning Holder? A 93° cutting angle on the Teknik Makina Turning Holder helps with chip control and heat distribution, improving tool life and surface finish by reducing edge loading in demanding turning operations. Who should I contact for technical advice on installing the Turning Holder? For tailored setup guidance and additional technical data for the Turning Holder by Teknik Makina, contact METAV Werkzeuge — eMail: info@metav-werkzeuge.com or Tel: +49 2822 7131930; WhatsApp: +49 170 2837271. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#D368TM","sku":"D368TM","mpn":"D368TM","gtin13":"4061905153327","name":"SDJCL 2525 Turning Holder for DCMT 11T3, 93° Left","description":"150mm turning holder for DCMT 11T3 indexable inserts; ISO SDJCL 2525; 25x25mm shank, 32mm cutting head width; left-hand, 93° cut; Manufacturer: Teknik Makina","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/9f/13/35/64/6435139f4fcfb37a48907531/d360tm-main.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/d0/7e/de/62/62de7ed00f56dbb4de4dbf3f/d360tm-technische-zeichnung.jpg","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/2d/7e/de/62/62de7e2d148ec6b71020ff7a/d360tm-artikelliste.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Suitable Inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Overall Length","value":"150 mm"},{"@type":"PropertyValue","name":"Shank Width","value":"25 mm"},{"@type":"PropertyValue","name":"Shank Height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting Head Width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting Height","value":"30 mm"},{"@type":"PropertyValue","name":"Cutting Direction","value":"Left"},{"@type":"PropertyValue","name":"Cutting Angle","value":"93°"},{"@type":"PropertyValue","name":"Weight","value":"0.735 kg"},{"@type":"PropertyValue","name":"ISO Designation","value":"SDJCL 2525"},{"@type":"PropertyValue","name":"Designation 2","value":"M11"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 150 mm."}},{"@type":"Question","name":"What are the shank dimensions?","acceptedAnswer":{"@type":"Answer","text":"Shank width and height are 25 mm each."}},{"@type":"Question","name":"What is the cutting angle and direction?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle 93° with left-hand cutting direction."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/SDJCL-2525-D368TM","dateModified":"2026-03-31T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder SDJCL 2525"},{"@type":"Thing","name":"DCMT 11T3 Indexable Inserts"},{"@type":"Thing","name":"Teknik Makina"}],"mentions":[{"@type":"Thing","name":"25x25 mm shank"},{"@type":"Thing","name":"150 mm overall length"},{"@type":"Thing","name":"93° cutting angle"}]}]}

Turning Holder (Klemmhalter) SDNCN 2525 for DC-- 11T3 Inserts by Teknik Makina The Turning Holder (Klemmhalter) SDNCN 2525 delivers a rigid, indexable solution for precision external turning with DC-- 11T3 inserts. For DC-- 11T3 indexable inserts ISO SDNCN 2525 shank for consistent mounting 150 mm overall length for stable reach 25 × 25 mm shank for high rigidity 62.5° cutting angle for improved clearance Optimised rigidity and repeatability for turning tasks The Turning Holder is designed to secure Indexable Inserts reliably, delivering consistent cutting geometry across repetitive operations. Its SDNCN 2525 designation denotes a standardised shank interface that simplifies tool setup and repeatability at the toolpost. This results in reduced vibration and improved surface finish, which translates into fewer rework cycles and more predictable machining results for production Turning and workshop applications. Compact dimensions that enhance machining stability With an Overall Length of 150 mm and a 25 × 25 mm shank profile, this holder prioritises stability in external turning operations. The Cutting Head Width of 12.5 mm and a 62.5° Cutting Angle increase clearance for interrupted cuts and complex part geometries while maintaining support close to the cutting edge. These dimensions help minimise deflection and allow for higher feed rates without compromising precision. Easy insert handling and clear compatibility The holder is compatible with DC-- 11T3 inserts, enabling quick insert changes and straightforward tool management. For customers less familiar with tooling codes: "Indexable Insert" refers to a replaceable cutting tip that can be rotated or exchanged when worn, reducing tooling costs compared with one-piece cutters. The ISO-style designation SDNCN 2525 identifies the holder style and shank size, making it simpler to select matching toolholders and clamping accessories across different machines. Who benefits and where to use it Workshops, maintenance departments and small-series production environments benefit most from this holder’s balance of rigidity and accessibility. Its compact shank and standardised interface make it suitable for manual and CNC lathes where space is limited but consistent accuracy is required. The product comes in new condition and is listed as in stock, which supports rapid integration into ongoing tooling setups. Choose Teknik Makina’s Turning Holder for dependable clamping precision and consult METAV Werkzeuge for tailored technical advice — contact info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 for support and compatibility guidance Technical Details Designation: Klemmhalter Brand: Teknik Makina SKU: D124TM For Indexable Inserts: DC-- 11T3 Compatible Inserts: DC-- 11T3 Overall Length: 150 mm Weight: 0.705 kg ISO Designation: SDNCN 2525 Secondary Designation: M11 Shank Width: 25 mm Shank Height: 25 mm Cutting Head Width: 12.5 mm Cutting Angle: 62.5° GTIN: 4061905153372 Condition: New Availability: In Stock Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder by Teknik Makina? The Turning Holder (Klemmhalter) SDNCN 2525 from Teknik Makina accepts DC-- 11T3 indexable inserts; these inserts are specified for the holder’s insert pocket and ensure proper cutting geometry when mounted correctly. How does the SDNCN 2525 designation affect compatibility? SDNCN 2525 indicates the holder’s shank style and size; with this designation, the Turning Holder by Teknik Makina is compatible with tooling systems and clamping fixtures designed for a 25 × 25 mm shank. Can the Turning Holder handle heavy-duty cuts? The Teknik Makina Turning Holder’s 25 × 25 mm shank and compact 150 mm length provide enhanced rigidity suitable for many standard turned operations; for specific heavy-duty applications, METAV Werkzeuge can advise on optimal insert grades and machining parameters. Where can I get technical support for the Klemmhalter? For application support and detailed technical data regarding the Klemmhalter Turning Holder by Teknik Makina, contact METAV Werkzeuge at info@metav-werkzeuge.com, call +49 2822 7131930 or WhatsApp +49 170 2837271. 150mm SDNCN 2525 Turning Holder for DC-- 11T3 Indexable Inserts, 62.5° - Teknik Makina