100-125mm Three-Point Internal Micrometer Self-Centring With Hardened Measuring Faces In Plastic Case - Metav IndustryLine
Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100-150mm Three-Point Inside Micrometer Colour Touchscreen Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of precise three-point measurement, wireless data output with USB, and full ISO 17025 calibration for dependable bore inspection and traceable results; order via Metav Werkzeuge or consult the specialists for application advice. Three-point internal micrometer — digital, 100–150 mm measuring range, Wireless + USB, Microtech Metrology The Three-point internal micrometer is a digital, workshop-ready instrument for repeatable bore and internal diameter checks from 100 to 150 mm, designed for production quality control and laboratory verification. ISO 17025 calibration certificate included Wireless and USB data output Colour 1.5" touchscreen display High repeatability: 0.004 mm accuracy Reliable measurement where it matters The instrument delivers consistent three-point measurement across bores, reducing orientation error and improving repeatability compared with single-point probes. With a specified accuracy of ±0.004 mm, the device supports quality control procedures that demand tight tolerances. The standard-sized measuring range classifies the tool for typical workshop and machine‑shop applications, offering a practical balance between reach and rigidity for medium-sized components. Fast data capture and traceability for production Equipped with Wireless and USB data outputs and a Colour 1.5" touchscreen, the device streamlines data acquisition and logging without manual transcription. The high-resolution reading (0.0001 mm) ensures fine increments are visible on the display, while digital output supports integration into measurement software or SPC workflows. This lowers administrative effort and helps maintain a clear audit trail for batch releases. Practical handling that reduces operator influence The included adjustment ring simplifies zeroing and routine checks, and the three-contact measuring head minimises tilting errors during insertion into bores. A measuring depth of 250 mm allows access to deeper cavities while preserving stability. These ergonomic and mechanical details reduce the effect of operator technique on the measurement result, improving reproducibility across shifts. Certified delivery and industrial readiness This micrometer is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate, making it immediately suitable for accredited quality environments. The combination of high accuracy, digital interfacing and certified calibration positions the instrument as a reliable tool for incoming inspection, in‑process checks and final acceptance testing. Contact Metav Werkzeuge for tailored advice and secure a certified Microtech Metrology three-point internal micrometer (SKU 133715010) with ISO 17025 calibration for your measurement process Technical data Article number: 133715010 GTIN: 4061905074295 Manufacturer: Microtech Metrology ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 100–150 mm Resolution (reading): 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 250 mm Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Calibration: ISO 17025 certificate included Special features Three-point internal measurement Adjustment ring included Digital operation for SPC integration Suitable for workshop and lab use Delivered calibrated for traceability FAQ Is this instrument supplied calibrated? Yes. The Microtech Metrology three-point internal micrometer (SKU 133715010) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. Which measurement range does the instrument cover? The device covers a measuring range of 100–150 mm, which places it in the standard class for workshop and machine‑shop bore inspection tasks. How are measurement results exported? Measurement data can be exported either wirelessly or via USB, enabling direct transfer into inspection software or SPC systems from the Microtech Metrology instrument. What resolution and accuracy can be expected? The display resolution is 0.0001 mm and the specified accuracy is ±0.004 mm, suitable for stringent dimensional checks in production control. Is the touchscreen suitable for use with gloves? The 1.5" colour touchscreen provides clear readout and simple menus; for glove operation, common shop gloves may limit sensitivity—repeatable results are maintained via the device’s stable mechanical design. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
100mm Dial Indicator Colour 2.4" Touchscreen Wireless USB, Microcomputer, Modbus PLC Ready - Microtech Metrology
Take advantage of the combination of ±0.005 mm accuracy, a 0–100 mm measuring range and seamless Wireless + USB data transfer for faster inspection cycles and reliable traceability — order directly via Metav Werkzeuge or consult our specialists for integration advice. Digital dial gauge — 2.4" colour touchscreen, Wireless + USB (Microtech Metrology) The digital dial gauge is a compact electronic indicator designed for precision inspection and process data capture in production, quality control and calibration benches. Colour 2.4" touchscreen display Wireless and USB data output High precision: ±0.005 mm accuracy Measuring range 0–100 mm Precision that keeps production moving A reliable measurement device cuts rework and shortens inspection times. The digital indicator delivers an accuracy of ±0.005 mm combined with a display resolution of 0.0001 mm, enabling fine discrimination of dimensional variations that matter in serial production. This level of performance supports consistent acceptance criteria and reduces uncertainty in pass/fail decisions, so process control becomes both faster and more predictable. The compact format suits bench-mounted gauges and inline inspection stations where repeatable results are required. Fast data flow for traceable quality records Efficient capture and routing of measurement data reduces transcription errors and accelerates reporting. With Wireless and USB connectivity and a user-friendly 2.4" colour touchscreen, the instrument permits immediate transfer to SPC systems or PLCs and visual confirmation at the point of measurement. The device’s digital architecture supports straightforward logging of readings, improving traceability in audits and enabling quicker feedback to production. The touchscreen simplifies setup and unit selection, cutting operator time per measurement. Robust contact mechanics for steady results Consistent probe contact is essential for repeatable readings. The indicator’s measuring force of 1.2–2.2 N helps maintain stable contact without excessive deflection, making it suitable for delicate gauge work as well as routine inspection of machined parts. The electronic design minimises mechanical wear compared with analogue heads, so service intervals are extended and downtime reduced. Built with industrial use in mind, this indicator is appropriate for workshop benches, toolrooms and production lines that require dependable dimensional control. For measurement solutions tailored to production needs, contact Metav Werkzeuge to discuss application requirements, request technical documentation or arrange a customised supply plan — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 120139907M GTIN: 4061905453472 eClass: 21170308 Core specifications Measuring range: 0–100 mm Resolution (display): 0.0001 mm Accuracy: 0.005 mm Measuring force: 1.2–2.2 N Display: Colour 2.4" touchscreen Features Data output: Wireless + USB Digital indicator Category: Messuhren FAQ What measurement accuracy does the device deliver? The digital dial gauge achieves an accuracy of ±0.005 mm, suitable for precision inspection tasks where tight tolerances are required. How can measurement data be exported from the gauge? Data can be exported via Wireless and USB connections, allowing the digital dial gauge by Microtech Metrology (SKU 120139907M) to interface with SPC systems and PLCs. What resolution is shown on the display? The indicator provides a display resolution of 0.0001 mm, enabling fine-grained readings for detailed dimensional analysis. Which measuring range is covered by this indicator? The instrument covers a measuring range of 0–100 mm, making it appropriate for small to medium-sized components on the workshop bench. Is the contact force suitable for sensitive components? Yes. The measuring force is specified at 1.2–2.2 N, which balances secure contact with minimal influence on delicate parts when using the digital dial gauge. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
10mm Dial Test Indicator With Flexible Stand And Grip Clamp, Supplied In Case - Metav IndustryLine
Compact, workshop-friendly metrology kit combining a high-resolution 0–10 mm dial gauge with a versatile stand and grip clamp for reliable small-part checks; perfect for routine quality control and setup tasks. The 0.01 mm resolution and analogue simplicity deliver repeatable indications with minimal training. Order the 2-piece measuring set directly via Metav Werkzeuge or ask our consultants if needed. Metav IndustryLine 2-piece Dial Gauge Set — 0–10 mm Dial Gauge with Flexible-Arm Stand and Grip Clamp The Metav IndustryLine 2-piece dial gauge set is a compact metrology solution for precision checks, runout and comparative measurements in small workshops and fine-mechanical applications. 0.01 mm resolution dial gauge Flexible-arm stand for stable positioning Grip clamp for tubes Ø25 mm and sheet 20 mm Compact two-piece kit for micro measurements Precision where space is tight Designed for the micro range, this set covers a 0–10 mm measuring span with an analogue 0.01 mm reading, making it ideal for tasks that demand fine resolution in confined spaces. The small measurement range is matched with mechanical rigidity to reduce bending and torsion during measurement, so that repeatable measurements become the norm rather than the exception. The analogue display keeps interpretation straightforward while maintaining the sensitivity required for runout, depth and comparative checks in precision engineering and watchmaking contexts. Stable mounting for repeatable results The included stand features a flexible arm that allows fast alignment and secure positioning of the gauge over the test piece. The grip clamp is adapted for tubes up to Ø25 mm and sheet material up to 20 mm, enabling a wide variety of fixtures without additional tooling. With a total height of 320 mm and a practical mass that supports steadiness during probing, the assembly reduces setup time and measurement scatter, which in turn supports faster decision cycles on the shop floor and fewer reworks. A compact kit that keeps workshop checks fast Supplied as a two-piece kit, the contents comprise one dial gauge and one measuring stand with the grip clamp, offering a complete, portable solution for routine inspection tasks. The analogue gauge is valued for its robustness and ease of use where digital interfaces are unnecessary or undesired; maintenance is straightforward and calibration intervals are easily managed within existing quality processes. For small-batch production, toolroom set-up or incoming inspection, this compact solution delivers dependable visual feedback that complements digital systems without complication. Choose the Metav IndustryLine dial gauge set for precise micro-range checks and contact Metav Werkzeuge for technical guidance or to secure supply from our Emmerich warehouse Technical Data Article number: M300.019 GTIN: 4054469181523 Contents: 1x dial gauge, 1x flexible-arm stand with grip clamp Weight: 1.8 kg Total height: 320 mm Facts Measurement range: 0–10 mm Resolution: 0.01 mm Pieces per set: 2 Special features Analogue dial gauge with 0.01 mm graduation Flexible-arm stand for fast alignment Grip clamp for tubes up to Ø25 mm and sheet up to 20 mm Compact two-piece measuring set FAQ What is the measurement range and resolution of the set? The set provides a 0–10 mm measuring range with a 0.01 mm analogue graduation, suitable for fine-detail measurements. What is included in the M300.019 kit? The M300.019 set includes one dial gauge and one measuring stand with flexible arm and grip clamp, supplied as a ready-to-use two-piece kit. Can the stand hold round and flat workpieces? Yes, the grip clamp is designed to secure tubes up to Ø25 mm and flat material up to 20 mm, enabling both round and sheet applications. Is the gauge suitable for runout and comparative checks? The analogue indicator and stable mounting make the kit well suited to runout, flatness and comparative inspections in small-part production or toolroom settings. Who manufactures the set and where is it supplied from? The set is part of the Metav IndustryLine range and is supplied via Metav Werkzeuge from Emmerich for reliable European distribution. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10–12mm Three-Point Inside Micrometer Self-Centering, Supplied in Case - Metav IndustryLine
The combination of precise self‑centring contact, a compact 10–12 mm measuring range and robust carbide faces ensures fast, repeatable blind‑hole measurements with minimal setup. Order the instrument directly via Metav Werkzeuge or consult the team for application advice. Metav IndustryLine Three‑Point Internal Micrometre MS908.652 — self‑centring, 10–12 mm range The Three‑Point Internal Micrometre MS908.652 is a compact analogue micrometre designed for precise diameter measurement inside blind holes and small bores in the 10–12 mm range. Self‑centring three‑point contact Measuring range 10–12 mm Accuracy 0.004 mm Carbide measuring faces Reliable centring for blind‑hole measurement A three‑point contact ensures rapid and reproducible alignment in blind holes, reducing repositioning time and measurement scatter. The micrometre’s self‑centring mechanism automatically locates the bore centre, so the operator obtains a consistent contact geometry on each measurement. With a measuring span of 10–12 mm the instrument is tailored to micro components and small bores where repeatability and short setup times are essential, improving throughput in small‑part inspection tasks. Durable contact surfaces for longer service life The measuring faces are manufactured as carbide contacts to resist wear and preserve accuracy during frequent use. The unit’s analogue design gives a tactile feel and straightforward reading, paired with a fine adjustment capability to approach tight fits carefully. The compact body (length approx. 54.5 mm) is suited to constrained access, while a setting ring (size 10) is included for verification and quick zeroing, supporting stable traceability in routine quality checks. Practical workflow advantages and workshop integration This three‑point micrometre combines simple operation with technical reliability: measurements are quick, calibration checks are straightforward and the tool integrates easily into existing inspection benches. Classified in the Micro range (max. 10–100 mm), it fulfils typical needs of precision engineering, watchmaking and small‑component production where stiffness, reach and single‑hand operation must be balanced. Metav’s distribution ensures European stock and reliable delivery from Emmerich. Request application guidance or order details from Metav Werkzeuge for the Metav IndustryLine three‑point internal micrometre MS908.652 — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.652 Brand: Metav IndustryLine Category: Micrometres Type: Three‑point internal micrometre Measuring range: 10.0–12.0 mm Minimum range: 10 mm Maximum range: 12 mm Accuracy: 0.004 mm Length: 54.5 mm Setting ring: 10 Self‑centring three‑point contact Carbide (hard metal) measuring faces Analogue operation (nonius style) Suitable for blind‑hole bores FAQ How does the three‑point contact improve measurement in blind holes? The three‑point geometry of the MS908.652 centres automatically in a bore, giving a stable contact triangle that reduces wobble and improves repeatability compared with single‑point probes. What measurement accuracy can be expected from this instrument? The instrument is specified with an accuracy of 0.004 mm; in routine use this delivers repeatable diameter readings for small‑bore inspection tasks. Is the micrometre suitable for workshop use or only for laboratory conditions? Designed for practical workshop use, the robust carbide faces and analogue adjustment make the MS908.652 resilient to frequent handling while keeping measurement quality high. How is the instrument returned to zero or checked on site? A setting ring (size 10) is provided for quick verification and zeroing of the micrometre before inspection runs. Which components and applications benefit most from this micrometre? Small bores, precision fittings, watch‑ and micro‑mechanical parts and any blind‑hole diameters in the 10–12 mm range benefit from the compact form, self‑centring contact and carbide faces of the MS908.652. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10–12mm Three-Point Internal Micrometer Color Touchscreen, Wireless USB, ISO 17025 Calibrated - Microtech Metrology
Benefit from the combination of three-point contact stability, a colour touchscreen readout and ISO 17025 traceable calibration to secure reproducible internal measurements in the 10.0–12.0 mm range. Order the Three‑Point Internal Micrometer directly via Metav Werkzeuge or consult our specialists for integration advice. Three‑Point Internal Micrometer — digital instrument with Wireless + USB (Microtech Metrology) The Three‑Point Internal Micrometer is a precision instrument for stable internal diameter measurement in small bores, suitable for quality control and bench metrology in workshops and production. Three-point contact for stable internal measurements Colour 1.5" touchscreen for clear readouts Wireless and USB data output for traceable transfer Delivered calibrated to ISO 17025 with certificate Dependable accuracy where tight tolerances matter The instrument combines a three-point contact measuring head with a high‑precision mechanism to reduce runout and centring error, delivering an accuracy of ±0.004 mm across its measuring span. With a measuring range of 10.0–12.0 mm, this device is aimed at fine internal dimensions where repeatability and a low measurement uncertainty are decisive. The robust contact geometry and confirmed specification make it well suited to small‑bore inspection tasks in component finishing and final inspection workflows, supporting a rational decision process for integrating metrology into production control. Seamless data capture for quality documentation Digital measurement is presented on a Colour 1.5" touchscreen for fast reading and reduced interpretation errors; the unit also provides Wireless and USB data output for direct transfer into SPC systems or inspection software. Combined with the included calibration trace, this workflow supports rapid documentation and traceability. The instrument’s readable display and straightforward data export reduce process steps and the risk of transcription mistakes, promoting efficiency and error‑resilient quality reporting in serial inspection and laboratory environments. Practical design for everyday workshop use A compact measuring head with an extended measuring depth of 154 mm keeps handling comfortable while reaching into bores and recesses. A setting ring is included to simplify zeroing and periodic checks. Delivered fully calibrated to ISO 17025, the micrometer arrives with a formal calibration certificate, providing immediate confidence for compliance audits and internal quality routines. The combination of robust measuring geometry, clear digital feedback and certified calibration supports both operational ease and trustworthy results, reinforcing productive workflows and peace of mind in routine inspections. For traceable high‑precision internal measurement solutions from Microtech Metrology, contact Metav Werkzeuge for ordering and application support — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 133701210 GTIN: 4061905074202 Manufacturer: Microtech Metrology Numbers Measuring range: 10.0–12.0 mm Measuring depth: 154 mm Accuracy: ±0.004 mm Resolution/readout: 0.0001 mm Special features Digital display: Colour 1.5" touchscreen Data output: Wireless and USB Setting ring: included Delivered calibrated to ISO 17025 with certificate FAQ Is the instrument delivered with a calibration certificate? Yes. The Three‑Point Internal Micrometer from Microtech Metrology is supplied fully calibrated to ISO 17025 and includes the calibration certificate for traceability. What measurement range is covered by this micrometer? The device covers internal diameters from 10.0 to 12.0 mm and is designed specifically for high‑precision work within that span. How is measured data transferred to a PC or quality system? Measurement results can be exported via both Wireless and USB connections, enabling straightforward integration into inspection software and SPC workflows. What advantage does the three‑point contact offer? Three contact points centre in the bore automatically, reducing eccentricity and improving repeatability compared with two‑point methods, which is why this geometry is preferred for small‑bore internal measurements. Can the micrometer reach recessed bores? Yes. The instrument’s 154 mm measuring depth allows access to deeper internal features while maintaining the necessary measurement stability. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
12-16mm Three-Point Internal Micrometer Colour Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of high accuracy, wireless + USB data transfer and full ISO 17025 calibration with certificate for reliable measurements in precision workshops; order the three-point internal micrometre directly via Metav Werkzeuge or ask our consultants for tailored advice. Three‑Point Internal Micrometre – Digital internal measuring tool with wireless + USB and 1.5" colour touchscreen (Microtech Metrology) The Three‑Point Internal Micrometre is a compact digital instrument engineered for precise internal diameter measurement in small bores and precision components within the micro measurement category. *Digital display: 1.5" colour touchscreen *Wireless and USB data output *ISO 17025 calibrated with certificate *Measuring range 12–16 mm, 0.004 mm accuracy Accurate measurements for micro components Classified in the Micro category (suitable for very compact tasks), this instrument covers a measuring range of 12.0–16.0 mm, offering a practical reach for miniature assemblies and precision parts. The instrument combines a fine resolution of 0.0001 mm with a guaranteed accuracy of ±0.004 mm, which reduces measurement uncertainty and supports reproducible inspection results. Such precision is particularly valuable when inspecting small bores in sub‑assemblies where even slight deviations can affect fit and function. Traceable data capture and delivered calibration Designed for modern production environments, the micrometre provides wireless and USB connectivity for straightforward data transfer into inspection logs and SPC systems. The 1.5" colour touchscreen simplifies reading and setting adjustments on the shop floor, while the supplied setting ring ensures fast zeroing and repeatable reference points. The tool is supplied fully calibrated to ISO 17025 and includes a calibration certificate, enabling formal traceability and immediate use in processes that require accredited measurement results. Ergonomic handling that speeds up inspections The three‑point contact design centres measurement force, improving contact consistency inside bores and reducing operator‑induced variation. The compact format supports single‑hand operation in confined spaces and the intuitive touchscreen speeds routine checks, lowering cycle times and decreasing the likelihood of rework. The included setting ring and clear digital readout combine to make daily inspection routines both ergonomic and efficient. Integration into workshop quality routines With its digital outputs and compact form factor, the device integrates easily into existing inspection stations and handheld workflows. The substantial measuring depth of 230 mm provides versatility when accessing deeper bores or assemblies, while the three‑point mechanism ensures stable centring for reliable interior measurements. Together, these features support a consistent quality chain from initial inspection through to final acceptance. Contact Metav Werkzeuge in Emmerich for a suitability review or to request a quotation for this Microtech Metrology three‑point internal micrometre with ISO 17025 calibration; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 133701610 GTIN: 4061905074219 Manufacturer: Microtech Metrology ECLASS: 21170335 Facts Measuring range: 12.0–16.0 mm Resolution: 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 230 mm Special features Digital colour 1.5" touchscreen Data output: Wireless and USB Included setting ring ISO 17025 calibration with certificate Three‑point internal measuring spindle FAQ What bore sizes can be inspected with this instrument? The Three‑Point Internal Micrometre is designed for bores in the 12.0–16.0 mm range and is classified in the micro category for compact internal measurements. Is the micrometre delivered calibrated for traceability? Yes, the instrument is supplied fully calibrated to ISO 17025 and includes a calibration certificate for immediate traceable use. How are measurement results transferred to a PC or inspection system? Measurement data can be transmitted via the micrometre’s wireless interface or exported using the USB connection for integration into inspection logs. What level of precision can be expected during routine checks? Routine measurements with the Three‑Point Internal Micrometre offer a resolution of 0.0001 mm and an accuracy of ±0.004 mm, suitable for high‑precision shopfloor inspections. Does the tool include accessories for initial setup? The micrometre is supplied with an inclusive setting ring to establish a reproducible zero reference and support repeatable measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
12-16mm Three-Point Internal Micrometer Self-Centering, Plastic Case - Metav IndustryLine
Take advantage of the combination of compact design, repeatable self‑centring measurement and wear‑resistant carbide faces to maintain consistent bore quality in small components. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.653 — self‑centring three‑point head, carbide measuring faces (Metav IndustryLine) A Three‑point internal micrometer MS908.653 engineered for precise measurement of blind bores in workshop and quality‑control environments. Self‑centring three‑point measuring head Carbide measuring faces for wear resistance Precise range 12–16 mm with 0.004 mm accuracy Compact 80 mm body length for confined spaces Accurate measurements in confined bores The three‑point geometry provides a self‑centring effect that stabilises the measuring axis in blind holes, reducing eccentricity and improving repeatability. With a declared accuracy of 0.004 mm and a vernier reading increment of 0.005 mm, this analogue instrument delivers the fine mechanical resolution expected in micro‑component inspection. The design minimises operator variation by ensuring the measuring anvils expand symmetrically, which translates into faster decision‑making during incoming inspection or in‑process checks. Small format, specialist capability Classified in the Micro category (measuring range 12–16 mm), the tool combines a short 80 mm body length with a compact head that is easy to manoeuvre inside tight bores. The carbide measuring faces resist wear during repetitive use, extending the interval between maintenance cycles and preserving measurement integrity. An adjustment ring (size 16) allows repeatable pre‑settings for batch measurements, so set‑ups for small series or precision assemblies remain consistent without excessive rework. Built for blind‑hole tasks and straightforward handling Designed specifically for blind‑hole measurement, the three‑point micrometer eliminates the need for improvised measuring aids. Its analogue, non‑electronic construction favours robustness in workshop conditions and simplifies routine maintenance compared with electronic gauges. The combination of mechanical simplicity and the self‑centring head reduces measurement time and supports reliable dimensional control of bores used in bearings, housings and valve seats. Workshop integration and supplier confidence Metav IndustryLine supplies a practical measuring solution that fits established inspection routines and supports traceable quality processes. The instrument’s proven geometry and durable contact faces make it suitable for precision toolrooms and production lines where compact accuracy is required. For specification matching, calibration options and integration into existing quality workflows, Metav Werkzeuge acts as a single, reliable partner with rapid technical guidance and supply across Europe. Contact Metav Werkzeuge today for tailored technical advice and reliable supply of the MS908.653 three‑point internal micrometer via Metav Werkzeuge GmbH in Emmerich Technical data Article number: MS908.653 Brand: Metav IndustryLine Category: Messschrauben Facts Measuring range: 12.0–16.0 mm Measuring range (min): 12 mm Measuring range (max): 16 mm Body length: 80 mm Accuracy: 0.004 mm Reading increment: 0.005 mm Adjustment ring: 16 Special features Self‑centring three‑point head Carbide measuring faces Designed for blind‑hole measurement Analog/vernier design Compact micro‑class instrument FAQ What types of bores is this instrument intended for? This three‑point internal micrometer MS908.653 is designed for precise measurement of blind bores and internal diameters within its 12–16 mm range. How precise is the measurement and what resolution is readable? The instrument offers an accuracy of 0.004 mm with a vernier reading increment of 0.005 mm, providing fine mechanical resolution suitable for micro‑component inspection. Are the measuring faces durable for repetitive workshop use? Yes, the micrometer is fitted with carbide measuring faces to increase wear resistance during repetitive measurements and to maintain dimensional integrity. Is the micrometer suitable for small‑batch production set‑ups? Its compact 80 mm body and adjustment ring (size 16) enable repeatable pre‑settings, making the MS908.653 well suited to small series and frequent set‑ups. Can calibration or certification be arranged for this instrument? Calibration options and certificates can be arranged through Metav Werkzeuge; contact the supplier for available services and lead times. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12-20mm Three-Point Internal Micrometer Self-Centreing, 0.005mm Graduation, Supplied In Case - Metav IndustryLine
Benefit from self‑centring three‑point measurement, carbide measuring faces and a 0.005 mm vernier resolution to perform reliable blind‑hole checks in the micro range; order this precision set directly via Metav Werkzeuge or consult our experts for application guidance. Three‑point internal micrometer MS908.672 — 12–20 mm range, 0.005 mm vernier (Metav IndustryLine) The Three‑point internal micrometer MS908.672 is an analogue, self‑centring gauge designed for accurate measurement of blind bores within the micro range, where compact size and repeatable centring are essential. Self‑centring three‑point measurement Carbide measuring faces for wear resistance Resolution 0..005 mm for fine readings Precision where small tolerances matter This instrument is tailored to the micro range (12–20 mm), a segment where stiffness and compactness determine repeatability. The three‑point geometry automatically centres in blind bores, reducing operator alignment error and speeding up routine checks. With an analogue vernier reading at 0.005 mm, the gauge enables fine discrimination that supports tight tolerances without the complexity of digital systems. The compact format is especially useful in repair benches, toolrooms and micro‑assembly stations where space and manoeuvrability are constraints. Durable construction for frequent shop use Key contact surfaces are fitted with carbide measuring faces, providing excellent resistance to wear and abrasion and maintaining measurement integrity over many cycles. The instrument’s analogue vernier construction offers a robust, low‑maintenance solution for production environments. An adjustment ring (16) allows controlled settling of the measuring head, while the solid mechanical design minimises play and drift during repeated inside measurements. Practical set composition and extendibility Supplied as a set of two, the micrometers offer complementary coverage for daily shop workflows and quick changeover between inspection tasks. Extensions of 150 mm are available for deeper blind bore access, enabling the same measuring principle to be applied where reach is required. The compact set format reduces tool change time and simplifies storage for inspection kits on the shop floor. Application suitability and operator benefit Designed specifically for blind‑hole measurement, the gauge removes the need for complex adapters in many common tasks. The self‑centring action reduces the influence of operator alignment, while the fine vernier graduation supports confident pass/fail assessments in first‑operation inspection and incoming goods control. The analogue nature makes it straightforward to interpret results and integrate the device into established quality routines without training overhead. For tailored technical advice or to reserve this two‑piece precision set, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: MS908.672 Type: Three‑point internal micrometer Brand: Metav IndustryLine Designation: Three‑point internal micrometer Measurements Measuring range: 12.0–20.0 mm Resolution (reading): 0.005 mm Adjustment ring: 16 Set quantity: 2 pieces Special features Self‑centring three‑point system Carbide measuring faces Analogue vernier scale Suitable for blind‑hole measurement Extensions: 150 mm FAQ What measuring range does the instrument cover? The Three‑point internal micrometer MS908.672 covers a measuring range of 12.0–20.0 mm, placing it in the micro range suitable for fine mechanical work. Is this gauge suitable for blind‑hole inspection? Yes — the self‑centring three‑point design is specifically intended for blind‑hole (Sackloch) measurement and ensures reliable centring in such applications. How fine is the reading and how is it read? The analogue vernier provides a reading resolution of 0.005 mm; readings are taken from the vernier scale, offering precise manual measurement without electronics. Are the measuring faces robust enough for regular use? Measuring faces are made of carbide, giving the MS908.672 high wear resistance and long service life even under frequent shop use. Does the delivery include extensions and how many pieces are supplied? The delivered set comprises two instruments and includes extensions of 150 mm to extend reach into deeper blind bores. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.5mm Digital Indicator With Microcomputer, Modbus PLC Wireless+USB - Microtech Metrology
Take advantage of the combination of precise measurement, flexible data output and straightforward PLC integration to streamline inspection routines; the Microtech Metrology dial gauge delivers repeatable readings with a compact footprint — order the instrument directly via Metav Werkzeuge or consult the Metav team for system integration. Microtech Metrology Dial Gauge — digital indicator with Modbus PLC connection and 2.4" touchscreen A Microtech Metrology dial gauge built as a compact digital indicator for high-resolution displacement measurement and direct integration into PLC systems and data-collection setups Modbus PLC connection and wireless data 2.4-inch colour touchscreen display High accuracy: 0.002 mm Compact 0–12.5 mm measuring range Reliable precision for routine inspection and quality control The instrument provides 0.002 mm accuracy with a fine resolution of 0.0001 mm, making it suitable for high-precision checks on small components and assemblies. The compact 0–12.5 mm measuring range covers typical fine‑mechanical tasks while the specified measuring force of 0.6–1 N maintains consistent contact pressure, reducing variability between readings. These technical characteristics translate into reliable pass/fail decisions and shortened inspection times, supporting repeatable quality control without the overhead of larger metrology systems. Integration that reduces manual steps and speeds data flow Equipped with Modbus for PLC connectivity and dual wireless + USB data outputs, the indicator allows direct transmission of measurement values to machine control or data-logging systems. The built-in microcomputer handles signal processing locally, so measurement results are presented immediately on the 2.4" colour touchscreen and can be forwarded to production databases without intermediary conversion. This direct data path decreases transcription errors and facilitates automated traceability, offering a clear efficiency gain in production environments that demand documented results. Practical design for everyday workshop and laboratory use The device combines a compact, serviceable form factor with an intuitive touchscreen interface that simplifies setup and reading interpretation. The digital indicator’s construction supports frequent handling in both bench‑top and in‑process checks, while the display’s clarity improves operator confidence and reduces training time. Supplied by a trusted metrology brand and distributed through Metav Werkzeuge’s European quality filter, this solution brings professional measurement performance to workshops that require dependable, easy-to-integrate instruments. Contact Metav Werkzeuge in Emmerich for advice on PLC integration, delivery options and to source Microtech Metrology dial gauges for immediate use in production. Technical Data Article number: 120139137M GTIN: 4061905453397 Manufacturer: Microtech Metrology Facts Measuring range: 0–12.5 mm Accuracy: 0.002 mm Resolution (display/readout): 0.0001 mm Measuring force: 0.6–1 N Display: 2.4" colour touchscreen Data output: Wireless, USB, Modbus PLC Special features Integrated microcomputer for local processing Designed for direct PLC integration via Modbus Compact digital indicator for precision tasks Suitable for bench and in-process measurement Category: dial gauge / digital indicator FAQ What measurement range does the dial gauge cover? The dial gauge covers a 0–12.5 mm range, suitable for fine mechanical inspections and small-part measurement tasks. How accurate is the instrument for quality checks? The instrument achieves 0.002 mm accuracy with a readout resolution of 0.0001 mm, providing reliable precision for routine quality control. Which data interfaces are available for automation? Measurement values can be exported via Modbus for PLCs and transmitted over wireless or USB connections for data logging and process integration. Is the display suitable for shop-floor conditions? Yes; the 2.4" colour touchscreen offers clear, legible readings and straightforward operation, reducing operator errors and setup time. Can the measurement values be sent directly to a control system? Yes. The built-in Modbus connection and the device’s microcomputer enable direct transfer of values to control systems or databases without extra converters. Microtech Metrology: Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
12.7mm Digital Dial Gauge Absolute System 0.001mm Resolution 330° Rotatable Display IP54 - Metav IndustryLine
Take advantage of precise measurement, a rotatable readout and robust protection to keep inspection routines efficient and reproducible; the combination of 0.001 mm resolution, an absolute measurement system and IP54 ingress protection ensures reliable results across workshop and laboratory tasks. Order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. M301.035 digital dial indicator — 12.7 mm range, 0.001 mm resolution The M301.035 is a compact digital indicator designed for contact measurement tasks in quality control and precision assembly, offering an absolute measuring system and a rotatable display for flexible mounting and easy reading Absolute measurement system, 0.001 mm resolution 12.7 mm measuring range 330° rotatable display for flexible reading IP54 protection against dust and splashes Precision that reduces rework and secures tolerances The gauge delivers an outstanding combination of 0.001 mm display resolution and an accuracy of 0.002 mm, helping to detect small deviations before they escalate into costly production faults. The excellent repeatability of 0.004 mm provides stable results across repeated checks, which streamlines process control and supports consistent part quality. The absolute measuring system removes ambiguity after power cycles, so reference points remain intact and measurement workflows become faster and less error-prone. Readability and durability for everyday shop use A 330° rotatable display and a clear digital readout simplify measurement in confined fixtures and awkward orientations, while the IP54 rating protects the electronics from dust and coolant splashes commonly found in machine shops. The instrument runs from a 3 V supply and features a scale with a glass rail for improved scanning stability, reducing measurement jitter. Supplied in a transport case for safe handling, the gauge combines ergonomic operation with the robustness required for routine inspection and bench use. Connectivity and functions that support traceable workflows The unit offers a practical keypad layout (ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/inch and +/-) and a data output RB 6 for external data capture, enabling straightforward logging of measured values into inspection records. With a measuring force greater than 1.5 N and a compact mass of 0.29 kg, the indicator balances gentle contact with mechanical stability. The 12.7 mm travel is ideal for small to medium measurement tasks, providing enough range for many workshop applications while retaining fine control and stiffness. Contact Metav Werkzeuge for tailored advice on the Metav IndustryLine M301.035 digital indicator and to arrange supply or technical clarification via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M301.035 GTIN: 4054469158389 Label: Digital indicator, 12.7 x 0.001 mm, Absolute system, 330° rotatable, IP54 Manufacturer: Metav IndustryLine Facts Measuring range: 0–12.7 mm Resolution: 0.001 mm Accuracy: 0.002 mm Repeatability: 0.004 mm Measuring force: >1.5 N Weight: 0.29 kg Protection class: IP54 Power supply: 3 V Display rotation: 330° Special features Absolute measurement system Digital display with ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/inch, +/- keys Data output: RB 6 Scale with glass rail for improved scanning Delivered in transport case FAQ What is the measuring range and resolution of the indicator? The indicator has a 12.7 mm measuring range and a display resolution of 0.001 mm, suitable for fine workshop and quality inspection tasks. Is the display protected against coolant and dust? Yes, the instrument is rated IP54, so the electronics are protected against limited dust ingress and splashing liquids typical in machining environments. Can measurement data be exported for documentation? A data output RB 6 is provided for external data capture, allowing measured values from the gauge to be recorded in inspection logs or data collection systems. Does the instrument require recalibration on delivery? The gauge is supplied calibrated according to standard factory procedures and includes a transport case for secure delivery; for traceable certification please enquire about available calibration services if needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.7mm Digital Test Indicator 0.01mm Resolution, Rotating 0–330° Display, Absolute System, IP54 - Metav IndustryLine
Precise, robust and simple to integrate: the digital dial indicator combines 0.01 mm resolution, an absolute measuring system and a 330° rotatable display for straightforward inspection tasks; delivered in a protective transport case for safe handling. Order the digital dial indicator M301.031 directly via Metav Werkzeuge or ask our consultants if needed. M301.031 — Digital dial indicator, 12.7 mm range, 0.01 mm resolution (Metav IndustryLine) The M301.031 digital dial indicator is a compact measuring instrument for accurate short-range checks in workshop inspection and machining set-ups, featuring an absolute system and a rotatable display for ergonomic reading. Resolution 0.01 mm Absolute measuring system Display rotatable 0–330° IP54 protection for workshop use Precision where it matters: consistent short-range measurement The indicator delivers a measuring range of 12.7 mm with a fine resolution of 0.01 mm, making it suitable for detailed measurement tasks and repeat checks. Its repeatability of 0.005 mm ensures that successive readings stay consistent within narrow tolerances, which is essential for quality control or tool setting. The integrated absolute measuring system prevents datum loss after power cycles, so reference points remain stable between jobs. Easy integration and reliable data transfer Designed for straightforward integration into inspection routines, the instrument offers a clear digital readout with functions such as ON/OFF, ORIGIN, 0/ABS, PRESET, TOL and mm/inch switching. A dedicated data output (RB 6) facilitates connection to data loggers or inspection software, enabling documentation without manual transcription. The compact build and low mass support quick fixture mounting and minimal inertia during probing. Ergonomic operation and workshop resilience A 330° rotatable display provides flexible viewing angles, reducing operator strain in confined set-ups and speeding up throughput. The scale uses a glass slide for accurate scanning and a measuring force above 1.5 N for stable contact. With an IP54 rating and a protective transport case included, the instrument tolerates typical workshop environments and is safeguarded during transit or storage. Practical benefit: more uptime, fewer errors By combining a robust enclosure, a rotatable, easy-to-read display and dependable repeatability, this indicator reduces measurement-related interruptions and rework. The compact form factor and clear digital functions accelerate routine checks and calibration tasks; this supports faster decision-making on the shop floor and steadier production flow without compromising measurement integrity. For tailored advice on integrating the Metav IndustryLine M301.031 into existing quality workflows or to request a quotation, contact Metav Werkzeuge in Emmerich for expert assistance and reliable delivery. Technical data Article number: M301.031 GTIN: 4054469158358 ECLASS: 21170308 ETIM: EC003591 Weight: 0.29 kg Protection class: IP54 Measuring range: 0–12.7 mm Numbers / Core technical data Resolution: 0.01 mm Repeatability: 0.005 mm Measuring force: >1.5 N Measuring system: Absolute, 3 V Display rotation: 0–330° Data output: RB 6 Special features / Versions Digital functions: ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/inch, +/− Scale with glass slide for accurate scanning Reversible measuring direction possible Delivered in a protective transport case Designed for workshop inspection and tool setting FAQ How accurate is the M301.031 for repeat measurements? The M301.031 offers a repeatability of 0.005 mm, which supports reliable successive readings suitable for routine inspection and tool setup. Can the indicator display be read in different orientations? Yes, the instrument features a 330° rotatable display, allowing the screen to be turned for optimal readability in confined or awkward measuring positions. Is the M301.031 suitable for data logging with inspection systems? The gauge includes a data output (RB 6) for connection to compatible data loggers or inspection software to record measurements without manual entry. What environmental protection does the indicator provide? With an IP54 rating and a protective transport case included, the M301.031 is protected against dust ingress and splashing water typical in workshop settings. Which functions support quick setup and tolerance checks? Built-in functions such as 0/ABS, PRESET and TOL facilitate fast zeroing, presetting of reference values and basic tolerance monitoring during routine checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125-1000mm Internal Micrometer Digital, ISO 17025 Calibrated, IP65 - Microtech Metrology
Take advantage of the combination of a wide measuring range, robust IP65 protection and an ISO 17025 calibration certificate to secure reproducible bore measurements in production and inspection. Order the device directly via Metav Werkzeuge or ask the Metav consultants for detailed application advice. Microtech inside micrometer – Digital, IP65, 125–1000 mm A Microtech inside micrometer designed for precise internal diameter measurement across large bores and adaptable to workshop and metrology environments. Digital display, IP65 protected Measuring range 125–1000 mm Calibrated to ISO 17025 Accuracy ±0.015 mm Accurate, repeatable data for quality control The measuring system delivers traceable results thanks to the included ISO 17025 calibration certificate, making the instrument suitable for production control and incoming inspection. With a declared accuracy of ±0.015 mm and a fine display resolution of 0.0001 mm, the device provides the numerical certainty required for process capability assessments. The digital readout simplifies data capture and reduces transcription errors, supporting faster decision-making on the shop floor and in the measurement lab. Robust construction for demanding workshop conditions Built to withstand industrial use, this instrument features an IP65 rating that protects the electronics from dust and spray, extending service life in harsher environments. The construction is optimised for stable handling during deep-bore work: the measurement interface has a 22 mm diameter for secure contact and consistent seating in the bore. The solid mechanical design reduces measurement scatter and supports reproducible results even when used in production settings with frequent handling. Flexible range with extendable rods for larger bores The modular extension system allows coverage from 125 mm up to 1,000 mm without compromising stiffness. The delivery scope includes a set of extension rods (25; 50 (2); 100 (2); 200; 400 (2)) so larger internal diameters can be reached economically and accurately. This modular approach reduces the need for multiple instruments and speeds up set-up times, which benefits throughput where varying bore sizes occur in the same production run. Ready-to-use calibration and straightforward integration Supplied fully calibrated under ISO 17025, the instrument arrives ready for immediate use with a calibration certificate included in the delivery. The combination of a digital output, rugged protection class and factory calibration supports integration into quality management processes and traceability chains. Metrology teams and workshop supervisors will value the reduced lead time from receipt to production-ready status and the documented compliance for audits. Choose the Microtech inside micrometer for robust, ISO‑traceable bore measurement and contact Metav Werkzeuge in Emmerich for application-specific advice or ordering assistance Technical data Article number: 133800100 GTIN: 4061905041709 Manufacturer: Microtech Metrology Digital: yes IP rating: IP 65 Numbers / Core technical data Measuring range: 125–1000 mm Accuracy: ±0.015 mm Display resolution: 0.0001 mm Diameter: 22 mm ISO 17025: calibrated and certificate included Special features / Versions Digital readout with robust housing Extension rods included: 25; 50 (2); 100 (2); 200; 400 (2) Suitable for internal diameter and bore measurement eClass: 21170335 / ETIM: EC003590 FAQ What measurement range does this inside micrometer cover? The instrument covers a measuring range from 125 mm to 1000 mm, enabled by the supplied extension rods for larger bores. Is the device delivered calibrated for traceability? Yes, the Microtech inside micrometer is supplied fully calibrated under ISO 17025 and includes the calibration certificate with delivery. How accurate is the inside micrometer in typical use? The declared accuracy is ±0.015 mm, with a display resolution of 0.0001 mm, suitable for standard industrial inspection tasks. Can the instrument be used in a workshop environment with dust and coolant? The IP65 protection rating safeguards the digital electronics against dust ingress and low-pressure water jets, making it appropriate for challenging shop-floor conditions. Which accessories are supplied to extend the measuring range? The delivery includes extension rods in the sizes 25; 50 (2); 100 (2); 200; 400 (2), allowing the micrometer to reach up to 1000 mm. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
125-1500mm Internal Micrometer Digital, IP65, ISO 17025 Calibrated - Microtech Metrology
Combine 0.0001 mm display resolution with a robust IP65 enclosure and an ISO 17025 calibration certificate to ensure repeatable measurements on long internal diameters; the extended rod set facilitates measuring up to 1,500 mm. Order the internal micrometer directly via Metav Werkzeuge or ask our consultants for further technical clarification. Internal Micrometer – Digital internal measuring instrument, IP65, Microtech Metrology The Internal Micrometer is a digital instrument for precise internal diameter measurement across a 125–1,500 mm range, optimised for production metrology and workshop quality control. Digital display with 0.0001 mm resolution IP65 protection for dust and splash resistance ISO 17025 calibration certificate included Range 125–1,500 mm with extension rods High-resolution measurement for large bores The design delivers a fine display resolution of 0.0001 mm together with a stated accuracy of ±0.015 mm, providing reliable numeric feedback when inspecting larger internal diameters. This combination reduces statistical uncertainty in serial inspection and speeds up go/no-go decisions on the shop floor. The digital readout minimises reading errors compared with mechanical scales, which improves throughput in batch inspections while preserving the traceability required for quality control. Robust construction for workshop and production use Equipped with an IP65 rating, the unit withstands dust and light spray, allowing use close to machining centres without compromising electronics. The compact measuring head (Ø 22 mm) and modular extension rods make the instrument practical for confined bores and long shafts alike. The construction balances stiffness and reach: the long measuring range is handled by a rod system that keeps deflection low while remaining manageable for single operators or paired use when needed. Traceable calibration and easy integration into inspection routines Delivered with an ISO 17025 calibration certificate, the instrument is ready for integration into formal inspection procedures and audit trails. The included calibration certificate documents measurement uncertainty and supports compliance with internal QA systems. The extended rod set (25 mm; 50 mm ×2; 100 mm ×2; 200 mm; 400 mm ×2) allows flexible setup without additional purchases, shortening setup time and reducing tool changeover in the measuring bay. Contact Metav Werkzeuge in Emmerich for specification advice or to request a quotation for the Microtech Metrology internal micrometer (SKU 133800150); technical consultants are available by phone or email at info@metav-werkzeuge.com / +49 2822 7131930. Technical data Article number: 133800150 GTIN: 4061905100222 Manufacturer: Microtech Metrology Calibration: ISO 17025 certificate included IP protection: IP65 Digital: yes Facts Measuring range: 125–1,500 mm Resolution (display): 0.0001 mm Accuracy: ±0.015 mm Measuring head diameter: 22 mm Special features Digital readout for reduced reading error Extension rods: 25 mm; 50 mm (2); 100 mm (2); 200 mm; 400 mm (2) Delivered calibrated to ISO 17025 Rated for dusty and splash-prone environments (IP65) Suited to long-range internal diameter inspection (long category) FAQ What measuring range does the instrument cover? The Microtech Metrology internal micrometer (SKU 133800150) covers a measuring range from 125 mm to 1,500 mm with the supplied extension rods. What resolution and accuracy can be expected? Resolution is 0.0001 mm on the digital display and the device specification lists an accuracy of ±0.015 mm. Is the instrument supplied calibrated? Yes, the instrument is delivered with an ISO 17025 calibration certificate, documenting traceable calibration and measurement uncertainty. Can the micrometer be used near machining centres? The IP65 rating protects the electronics against dust and spray, making the device suitable for use close to machining operations, provided standard local precautions are observed. Which extensions are included and how do they affect measurements? The supplied extension set includes 25 mm; 50 mm (2); 100 mm (2); 200 mm; 400 mm (2). Extensions increase reach while the specification accounts for accuracy across the stated measuring range. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
125-150mm Three-Point Internal Micrometer Self-Centring With Hardened Measuring Faces, Supplied In Case - Metav IndustryLine
Take advantage of the combination of self-centring three-point contact, hardened measuring faces and a protective case for reliable, repeatable blind-bore measurement; order directly via Metav Werkzeuge or request advice from our technical consultants. Three-point internal micrometer MS908.664 — self-centring design, 125–150 mm (Metav IndustryLine) The Three-point internal micrometer MS908.664 is a precision instrument for accurate measurement of blind bores and internal diameters in machine shops and inspection benches Self-centring three-point contact Accuracy ±0.005 mm Hardened measuring faces Supplied in protective case Consistent concentric measurement where it matters The instrument’s self-centring three-point contact mechanism converts small radial differences into a single, centred datum, ensuring high repeatability during blind-bore checks. With a mechanical resolution and accuracy of ±0.005 mm, the device supports tight tolerance verification and process control for internal diameters. This level of precision is particularly useful when comparing series parts or validating internal fits, as the three-point geometry minimises eccentricity and reduces operator-induced variation. Robust construction for repetitive workshop use A durable construction and hardened measuring faces protect the contact points from wear and maintain measurement integrity over prolonged use. The analogue, mechanical drive reduces complexity and avoids battery dependence, making the tool suitable for routine quality inspections on the shop floor. The overall length of 145 mm gives the reach required for its measurement range while keeping the instrument compact enough for stable handling during repeated checks. Ideal balance of reach and stiffness for standard applications Classified in the standard range for internal measurement instruments (125–150 mm), this micrometer offers the best compromise between measuring reach and structural rigidity. That balance is critical in metalworking and fixture assembly, where longer tools can introduce deflection and shorter tools lack coverage. The design is optimised for blind bores, providing reliable access and reproducible contact even when full through-access is not available. Delivered protected and ready for transport The instrument is supplied in a protective case to safeguard measuring faces and the mechanism during transport and storage. Built for regular inspection cycles, it integrates easily into workshop tool sets and measurement benches; its analogue readout is simple to interpret and maintain, supporting efficient quality routines without complex electronic calibration procedures. Contact Metav Werkzeuge for tailored advice on the Metav IndustryLine three-point internal micrometer MS908.664 and to arrange procurement or technical specification support; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.664 Manufacturer: Metav IndustryLine Type: Three-point internal micrometer Feature: Self-centring Measuring range: 125–150 mm Length: 145 mm Accuracy: 0.005 mm Reading: 0.005 mm Mechanism: Analogue Delivery: protective case Measuring faces: hardened Suitable for: blind bores Numeric data Measurement range: 125–150 mm Maximum measurement: 150 mm Minimum measurement: 125 mm Accuracy/resolution: 0.005 mm Length: 145 mm SKU: MS908.664 Design and special features Self-centring three-point contact Hardened measuring faces for wear resistance Analogue drive for low maintenance Compact length for stable handling Supplied in protective case for transport Intended for blind-bore measurement FAQ What measurement range does the instrument cover? The instrument covers a measurement range of 125–150 mm, placing it in the standard workshop range suitable for many machine‑building and metalworking applications; refer to MS908.664 for exact limits. What accuracy and resolution are specified? The device offers an accuracy and reading resolution of 0.005 mm, enabling reliable checks against typical tight tolerance requirements. Is the design suitable for blind bores? Yes — the self-centring three-point contact is engineered specifically to measure blind bores with improved concentricity and repeatability. Are the measuring faces wear-resistant? The measuring faces are hardened to resist wear and maintain consistent contact geometry during repetitive inspection tasks. Is a protective case included? The instrument is supplied in a protective case to secure the micrometer during transport and storage. Is the micrometer digital or analogue? This is an analogue instrument with a mechanical drive and a direct, tactile measuring feel appropriate for workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125-2000mm Inside Micrometer Digital Readout IP65, Calibrated to ISO 17025 - Microtech Metrology
Take advantage of the combination of ISO 17025 traceable calibration, a 125–2000 mm measuring range and robust IP65 protection for reliable long‑range internal measurement in production environments; order the internal micrometer directly via Metav Werkzeuge or ask our consultants for application advice. Microtech Metrology Internal Micrometer – digital, ISO 17025 calibrated The internal micrometer is a digital measuring instrument designed for long‑range internal diameter checks in toolmaking, fixture construction and heavy machining. ISO 17025 calibration certificate included IP65 protection for workshop conditions Measuring range 125–2000 mm Digital readout with 0.0001 mm resolution Precise long‑range measurement that stays reliable The instrument delivers reproducible results across a 125–2000 mm span, making it suitable for large bores and assemblies where consistent internal diameters are critical. With a stated accuracy of 0.02 mm and a high‑definition resolution of 0.0001 mm, the device separates the notions of resolution and measurement uncertainty clearly: the fine digital readout supports precise setting and trend detection, while the declared accuracy defines the reliable tolerance for quality control. This combination benefits production control and in‑process inspection by reducing rework and scrap through dependable size verification. Built for the workshop, guarded against contamination A workshop‑grade design with IP65 ingress protection ensures the electronics and measuring mechanism withstand dust and splash exposure typical in machining environments. The construction is aimed at long‑range handling: a compact measuring head (diameter 22 mm) and modular rod system minimise bending and enable stable positioning over the full measuring span. The robust build reduces measurement variation across multiple operators and shifts, supporting consistent throughput in demanding production contexts. Flexible extension system and intuitive digital operation Modular extension rods are supplied to cover the complete range: short and long extensions are available to bridge between the spindle and large bore surfaces, enabling efficient stepwise assembly for different component sizes. The digital readout simplifies read‑back and reduces transcription errors; numeric steps and clear display settings accelerate routine checks and help maintain production flow. The combination of modular extension rods and a clear electronic display makes measurements quicker to set up and easier to document in inspection plans. Traceable calibration for quality assurance Delivered fully calibrated to ISO 17025 with a corresponding certificate, the instrument integrates into accredited quality management systems without additional calibration steps. Traceability to an international standard provides auditors and quality engineers with verifiable measurement confidence and streamlines acceptance in regulated production. For companies consolidating supplier lists, this traceable supply from a recognised metrology manufacturer supports audit readiness and reduces administrative burden. For tailored advice on long‑range internal measurement or to secure supply of the Microtech Metrology internal micrometer and compatible extension rods, contact Metav Werkzeuge in Emmerich for expert consultation and prompt delivery. Technical data Article number: 133800200 GTIN: 4061905041716 Manufacturer: Microtech Metrology Digital display: yes IP rating: IP 65 ISO 17025: delivered calibrated with certificate Facts Measuring range: 125–2000 mm Resolution (display): 0.0001 mm Accuracy: 0.02 mm Diameter: 22 mm eCl@ss: 21170335 ETIM: EC003590 Special features Delivered calibrated to ISO 17025 with certificate Modular extension rods: 25 +50 (2 pcs) +100 (2 pcs) +200 (2 pcs) +400 (3 pcs) Robust construction for workshop use Suitable for long‑span internal diameter inspection Category: internal micrometers (Messschrauben) FAQ Is the instrument supplied with a calibration certificate? Yes. The Microtech Metrology internal micrometer (SKU 133800200) is delivered fully calibrated to ISO 17025 and includes the calibration certificate. What is the usable measuring range for this micrometer? The device covers a measuring span from 125 to 2000 mm, using the supplied modular extension rods to reach larger internal diameters. How does the resolution relate to accuracy on this instrument? The digital readout shows 0.0001 mm steps for precise indication, while the guaranteed measurement uncertainty is 0.02 mm, defining the reproducible tolerance for quality control. Is the unit suitable for workshop environments with coolant or dust? Yes. The micrometer is rated IP65, affording protection against dust ingress and low‑pressure water jets typical in machining environments. Are extension rods included and which sizes are available? Extension rods are available as described: 25, 50 (2 pieces), 100 (2 pieces), 200 (2 pieces) and 400 (3 pieces) to assemble the required measuring length. Who manufactures this internal micrometer? The instrument is produced by Microtech Metrology and is supplied calibrated for industrial use; refer to the product SKU 133800200 for ordering and traceability. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
125-3000mm Internal Micrometer Digital, IP65, ISO 17025 Calibrated - Microtech Metrology
Combine long-range internal measurement with robust protection and traceable calibration to ensure reproducible results on large bores. Benefit from the modular extension system and IP65 rating for reliable workshop use; order the internal micrometer directly via Metav Werkzeuge or consult our specialists for configuration advice. Internal Micrometer — digital long-range bore gauge, IP65 (Microtech Metrology) Internal Micrometer for extra-long internal measurements up to 3,000 mm with a high-resolution digital readout High-resolution digital readout 0.0001 mm Measurement range up to 3,000 mm IP65 dust and water protection ISO 17025 calibration certificate included Precision over long distances for large components This inside measurement system is designed as an extra-long solution for bores and internal features up to 3,000 mm, combining reach with repeatability. The instrument offers a digital readout with a display resolution of 0.0001 mm, while the specified measurement accuracy ±0.03 mm defines the dependable tolerance band for inspection tasks. The separation between display resolution and accuracy is explained here: the high display resolution helps detect small changes during alignment and adjustment, whereas the stated accuracy reflects the certified uncertainty of measurement under calibrated conditions. Typical applications include large housing bores, long spindle seats and toolroom inspection where length and stability matter. Built to withstand workshop conditions and repeat measurement cycles Constructed for regular use on the shop floor, the gauge features an IP65 rating that guards electronics against dust ingress and water jets, making it suitable for dusty or coolant-prone environments. The robust design with modular extension rods (25, 50, 100, 200, 400 mm modules in various counts) allows flexible assembly for a wide range of depths without resorting to ad-hoc fixtures. As a result, the system reduces handling time and improves reproducibility when measuring elongated cavities or stepped bores, supporting consistent quality control across production batches. Traceable calibration and configurable delivery for inspection-ready use Delivered fully calibrated with an ISO 17025 certificate, the device arrives ready for integration into quality assurance processes that require traceability. The included calibration certificate documents the measurement uncertainty and the test conditions used during verification. For inspection labs and manufacturing departments, this means immediate acceptance for documented measurement tasks and reduced lead time before first use. The modular extension set can be selected to match the measurement range required, simplifying inventory management for metrology equipment. Choose Microtech Metrology's calibrated internal micrometer for dependable long-range bore control and contact Metav Werkzeuge in Emmerich for specification support and tailored extension sets — info@metav-werkzeuge.com · +49 2822 7131930 Technical data Article number: 133800300 GTIN: 4061905041723 Brand: Microtech Metrology IP rating: IP65 Calibration: ISO 17025 certificate included Facts Measurement range: 125–3,000 mm Resolution (display): 0.0001 mm Accuracy: ±0.03 mm Extension rods: 25+50 (2)+100 (2)+200 (3)+400 (5) eClass: 21170335 ETIM: EC003590 Special features Digital internal micrometer / bore gauge Robust electronics sealed to IP65 Modular extension system for long-range measurement Supplied calibrated with traceable certificate High-resolution readout for alignment work FAQ What measurement range does the instrument cover? The device measures from 125 mm up to 3,000 mm, making it suitable for extra-long internal dimensions and deep bore inspections. Is the micrometer delivered calibrated and traceable? Yes, the instrument is supplied fully calibrated and includes an ISO 17025 calibration certificate that documents measurement uncertainty and traceability. What accuracy and resolution can be expected? The system provides a display resolution of 0.0001 mm while the certified accuracy is ±0.03 mm, reflecting the instrument's calibrated performance envelope. Can the set be adapted to different bore depths? The micrometer is modular: it uses extension rods in the supplied configuration (25, 50, 100, 200 and 400 mm lengths) to assemble the required measuring length for specific applications. Is the readout protected for use in industrial environments? Yes, the electronics are sealed to IP65, protecting the readout from dust and low-pressure water jets commonly encountered on shop floors. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
125mm–4000mm Internal Micrometer Digital Readout, IP65, ISO 17025 Calibrated - Microtech Metrology
Take advantage of reliable, traceable measurements and a robust digital readout to speed up inspection of large bores; the instrument’s IP65 protection and ISO 17025 calibration certificate support consistent workshop use and documented quality. Order directly via Metav Werkzeuge or consult the Metav team for configuration and delivery. Inside micrometer – digital, ISO 17025 calibrated (Microtech Metrology) The Inside micrometer is a digital internal-measuring instrument designed for large diameters and on-site inspection tasks across machine building and heavy fabrication. 0.0001 mm display resolution ISO 17025 calibration certificate included Measuring range 125–4,000 mm IP65 protection for workshop environments Reach big components with repeatable precision The instrument covers an extra‑long range (125–4,000 mm) by means of extension rods, which makes it suitable for measurements on housings, large bearings and pipe bores that require single‑setup inspection. The long measuring span is supported by a stable gauge geometry that reduces bending and lateral play; this translates into consistent repeatability when measuring across a structure rather than relying on multiple shorter gauges. The available extensions allow a modular approach to reach without compromising measurement chain integrity. Traceability and measurable assurance for quality control Calibrated to ISO 17025, the device is supplied with a calibration certificate, providing documented traceability for incoming inspection and production control. The instrument’s stated accuracy of 0.04 mm combined with a digital readout resolution of 0.0001 mm offers a clear balance between workshop robustness and reliable numerical output for reporting. For contract measurement or production release, the delivered certificate simplifies audit trails and reduces administrative queries during quality reviews. Rugged design for workshop integration and uptime With an IP65 rating and a compact measuring head with a 22 mm gauge diameter, the instrument tolerates coolant splash and dusty environments while maintaining stable contact with the measured surface. The digital interface speeds up read-off and reduces transcription errors compared with analogue alternatives; data output options are not listed, so it is treated as a stand‑alone measuring device with a robust display for immediate decision making on the shop floor. The modular extension set supplied covers common step increments, allowing flexible adaptation to a wide range of parts. Contact Metav Werkzeuge for tailored advice on configuration, delivery options and to discuss how the Microtech Metrology inside micrometer with ISO 17025 calibration can be integrated into existing inspection routines; Metav’s specialists in Emmerich will assist with selection and supply. Technical data Article number: 133800400 GTIN: 4061905041730 Manufacturer: Microtech Metrology Facts Measuring range: 125–4,000 mm Accuracy: 0.04 mm Display resolution: 0.0001 mm Diameter: 22 mm IP rating: IP65 Special features Digital readout ISO 17025 calibration certificate included Extensions: 25 + 50 (2 pcs.) + 100 (2 pcs.) + 200 (2 pcs.) + 400 (8 pcs.) eClass: 21170335 ETIM: EC003590 FAQ What measurement range does this instrument cover? The inside micrometer covers a measuring range from 125 to 4,000 mm, provided by the modular extension set supplied with the instrument. Is the instrument delivered calibrated and documented? Yes. The device is delivered with an ISO 17025 calibration certificate, documenting traceable accuracy for quality assurance and audit purposes. What accuracy and resolution can be expected? The instrument’s stated accuracy is 0.04 mm with a digital display resolution of 0.0001 mm, suitable for workshop and production control tasks requiring documented results. Can the micrometer be used in wet or dusty environments? The micrometer is rated IP65, which protects it against dust ingress and low‑pressure water jets, making it appropriate for typical workshop conditions. Which accessories are included for extended reach? The supplied extension set comprises 25, 50 (2 pcs.), 100 (2 pcs.), 200 (2 pcs.) and 400 (8 pcs.) rods to assemble the required measuring length up to 4,000 mm. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150-175mm Three-Point Internal Micrometer Self-Centring, 0.005mm Accuracy, Replaceable Anvils, Delivered in Case - Metav IndustryLine
Take advantage of the combination of precise 0.005 mm reading, a self‑centring three‑point measuring mechanism and interchangeable measuring inserts to ensure reproducible internal measurements of blind bores in the standard workshop range. Order the instrument directly via Metav Werkzeuge or consult the Metav team for application advice. Three‑point internal micrometer MS908.665 — self‑centring, 150–175 mm range (Metav IndustryLine) The three‑point internal micrometer is an analogue internal measuring instrument designed for reliable measurement of blind bores and internal diameters in the workshop and production environment. Self‑centring three‑point design Measurement range 150–175 mm Analogue reading 0.005 mm resolution Hardened measuring faces, interchangeable insert Reliable metrology for internal diameters and blind bores The three‑point design offers consistent contact on the bore surface, enabling reproducible centring even in deep blind holes. With a measurement range of 150–175 mm this instrument fits the standard class of workshop metrology where reach, stiffness and one‑hand operation are required. The analogue scale provides a clear 0.005 mm reading and an equivalent stated accuracy, which supports routine quality checks and rapid go/no‑go decisions on the shop floor. Practical handling and application benefits for production Interchangeable measuring inserts allow adaptation to differing bore geometries without replacing the whole instrument, reducing downtime and consumable cost. The self‑centring mechanism simplifies alignment and lowers operator variability, which increases throughput and decreases rework. Designed for internal measurements including blind bores, the tool is particularly suitable for machine shops, toolrooms and maintenance departments that require straightforward, rugged measuring devices for repeat measurements. Construction and durability tailored to industrial use Hardened measuring faces reduce wear and maintain measurement fidelity over long service periods; the instrument’s analogue mechanics are engineered for robustness rather than electronic sensitivity. The combination of hardened anvils, an interchangeable insert system and solid construction ensures long‑term stability under workshop conditions and predictable measurement behaviour when performing internal diameter checks on components. Contact Metav Werkzeuge in Emmerich for tailored advice on the MS908.665 three‑point internal micrometer and to arrange delivery from stock — info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: MS908.665 Name: Three‑point internal micrometer (Dreipunkt‑Innenmessschraube) Manufacturer: Metav IndustryLine Core technical data Measurement range: 150–175 mm Reading / resolution: 0.005 mm Accuracy: 0.005 mm Length: 145 mm Analogue instrument Special features Self‑centring three‑point design Hardened measuring faces Interchangeable measuring insert Suitable for blind bores Analogue scale, workshop grade FAQ What measuring range does the MS908.665 cover? The MS908.665 three‑point internal micrometer by Metav IndustryLine covers a measurement range of 150–175 mm. How fine is the resolution and what accuracy is stated? The instrument provides an analogue reading with 0.005 mm resolution and a stated accuracy of 0.005 mm for routine workshop control. Is the design suitable for blind hole measurements? Yes, the three‑point geometry and self‑centring action of this micrometer make it particularly suitable for reliable measurements in blind bores. Can the measuring faces be replaced if worn? The MS908.665 features an interchangeable measuring insert system; hardened faces prolong service life and can be renewed through the insert mechanism. For which workshop tasks is this micrometer intended? The instrument is designed for internal diameter checks in machine shops, toolrooms and maintenance operations where robust, repeatable analogue measurement is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Digital Dial Indicator Color 2.4" Touchscreen Wireless USB Modbus PLC Connection, 0.008mm Accuracy - Microtech Metrology
Benefit from the combination of high-resolution measurement, a responsive 2.4" colour touchscreen and flexible wireless and USB data export to keep quality control reliable and traceable; order the instrument directly via Metav Werkzeuge or consult our specialists for system integration. Digital Dial Gauge — 0–150 mm range with 2.4" colour touchscreen (Microtech Metrology) Digital Dial Gauge 0–150 mm, designed for precise shop-floor and inspection use, offers fast readings and modern data transfer for seamless process control 0–150 mm measuring range 2.4" colour touchscreen display Wireless and USB data output High reading resolution 0.0001 mm Precision that supports process control A measurement device with a 0–150 mm span and a resolution of 0.0001 mm delivers the repeatability required in production and incoming inspection. The instrument’s stated accuracy of ±0.008 mm positions it for fine tolerance checks where small deviations matter; the specified measurement force 3.2–5.2 N contributes to repeatable contact conditions and reduces variation caused by manual probing. These technical values translate into fewer rejected parts and more consistent process data when control limits are tight. Effortless data capture and traceability Integrated Wireless and USB outputs enable direct transfer of readings into inspection routines, SPC software or batch reports, removing error-prone manual transcription. The 2.4" colour touchscreen provides immediate visual confirmation of live values and simple menu navigation, which accelerates measurement cycles and shortens training time for new operators. The digital readout combined with reliable data transfer supports fast decision-making and smoother documentation for audit trails. Designed for repeatable measurements on the shop floor The compact, digital construction focusses on robust handling and clear legibility in workshop conditions. Ergonomic controls and a bright display reduce operator strain and make subsequent checks faster; the stable measurement force range helps to maintain reproducible contact across many cycles. Supplied by Microtech Metrology, this dial gauge suits routine in-process checks as well as quality-lab spot verifications, offering a practical link between bench inspection and digital quality management. Contact Metav Werkzeuge today to discuss integration options or request a tailored quotation for the Microtech Metrology digital dial gauge (SKU 120139505M) — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 120139505M GTIN: 4061905453533 ECLASS: 21170308 Manufacturer: Microtech Metrology Facts Measuring range: 0–150 mm Resolution (display): 0.0001 mm Accuracy: ±0.008 mm Display: 2.4" colour touchscreen Measurement force: 3.2–5.2 N Data output: Wireless, USB Special features Digital dial gauge design Colour touchscreen interface Wireless and USB connectivity Suitable for production and inspection tasks Category: Dial gauge (dial indicator) FAQ What measuring range does the instrument cover? The digital dial gauge covers a measuring range of 0–150 mm, suitable for standard workshop and inspection tasks. What accuracy and resolution can be expected? The device offers an accuracy of ±0.008 mm with a display resolution of 0.0001 mm, which supports fine tolerance checks in quality control. How are readings exported for documentation? Readings are exported via Wireless and USB interfaces; the Microtech Metrology dial gauge (SKU 120139505M) is configured for direct transfer into data-collection or SPC systems. Is the display suitable for busy shop-floor conditions? Yes; the 2.4" colour touchscreen provides clear visibility and intuitive navigation, aiding rapid checks even under challenging workshop lighting. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
16-20mm Three-Point Internal Micrometer Self-Centering, Calibrated in Wooden Case - Metav IndustryLine
Take advantage of self‑centring three‑point measuring, compact dimensions and a finely graduated reading for consistent blind‑bore checks; the combination of repeatable centring, carbide measuring faces and analogue robustness supports efficient workshop workflows. Order the Three‑point internal micrometer directly via Metav Werkzeuge or ask our consultants if needed. Three‑point internal micrometer MS908.654 — self‑centring, 16–20 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.654 is a precision instrument designed for reliable measurement of blind bores in the 16–20 mm band, combining a three‑point contact head with a compact frame for confined spaces Self‑centring three‑point head Measurement range 16–20 mm Carbide measuring faces (HM) Delivered in protective case Precise bore measurement where space is limited The three‑point contact design ensures automatic centring inside a blind bore so that the measuring points engage evenly; this reduces eccentricity and improves repeatability compared with single‑point probes. With a defined measurement range of 16–20 mm the instrument falls into the micro class of calipers, making it especially suitable for fine mechanical tasks and small assemblies where controlled measuring force and stable contact geometry are decisive for consistent results. The compact geometry helps to keep torsion low and supports reproducible checks in confined geometries. Workshop‑grade contact surfaces and durability Hard‑facing on the contact surfaces gives dependable wear resistance: the carbide measuring faces resist abrasion in routine shop use and extend service life under frequent contact with metal workpieces. The micrometer’s analogue construction avoids batteries and electronic vulnerabilities, favouring simple maintenance and immediate readiness. Supplied in a protective case, the instrument is shielded during transport and storage, supporting reliable deployment across different production stations. Readability and measurement certainty The instrument provides a fine reading step alongside a verified accuracy that supports confident decision making. With a display increment of 0.005 mm and an assessed accuracy of ±0.004 mm, the micrometer allows precise comparative measurements and go/no‑go assessments in production and quality control. The three‑point mechanism shortens setup time for successive measurements and reduces correctional effort, which increases throughput without compromising measurement integrity. Applications, classification and practical benefit Classified as a micro‑range internal micrometer, the tool is suited to watchmaking, valve seats, small hydraulic components and other blind‑hole checks where a short, rigid measuring system is required. The self‑centring function removes an additional alignment step, while the robust contact material supports mixed workshop environments. As a compact analogue instrument it combines mechanical simplicity with measurement quality, making it an efficient choice wherever repeatable internal diameters must be verified. For procurement or technical advice on Metav IndustryLine measuring instruments, contact Metav Werkzeuge in Emmerich for personalised guidance and secure delivery from our European warehouse Technical data SKU: MS908.654 Manufacturer: Metav IndustryLine Type: Three‑point internal micrometer Core specifications Measurement range: 16–20 mm Accuracy: ±0.004 mm Reading increment: 0.005 mm Overall length: 80 mm Analogue operation Features and materials Self‑centring three‑point head Carbide measuring faces Suitable for blind‑hole bores Delivered in protective case Compact micro‑range instrument FAQ What measurement range does this instrument cover? The Three‑point internal micrometer MS908.654 covers a range of 16–20 mm, designed for precise checks in small blind bores. How accurate is the micrometer for production checks? The instrument offers an assessed accuracy of ±0.004 mm with a reading increment of 0.005 mm, allowing reliable comparative measurements on small components. Are the contact faces suitable for regular shop use? Yes, the measuring faces are made of carbide, providing increased wear resistance and extended service life in routine workshop conditions with the Three‑point internal micrometer. Is this micrometer suitable for very tight or confined bores? Its compact frame and self‑centring three‑point head make the tool especially suitable for confined blind‑hole applications where stable contact and low torsion are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
175-200mm Three-Point Internal Micrometer Self-Centring, Interchangeable Anvils, Supplied in Case - Metav IndustryLine
Take advantage of the self‑centring three‑point contact, the 175–200 mm measuring range and the proven 0.005 mm accuracy to ensure reliable blind‑hole checks in routine inspection. Order the instrument directly via Metav Werkzeuge or ask the consultants for application advice. Three‑Point Internal Micrometer (MS908.666) — Self‑centring, 175–200 mm range; 0.005 mm accuracy Three‑Point Internal Micrometer (MS908.666) is a mechanical measuring instrument designed for precise measurement of blind holes in the standard workshop range. Self‑centring three‑point contact system Measuring range 175–200 mm High accuracy 0.005 mm Interchangeable measuring anvils Reliable centring for blind‑hole measurement The self‑centring three‑point contact design guarantees consistent alignment with the bore axis, reducing operator‑dependent variance during inspections. With a measuring range of 175–200 mm, this instrument falls into the standard class for workshop metrology: it combines sufficient reach with manageable stiffness for repeatable checks on housings and medium‑sized components. The mechanical, analog construction gives direct tactile feedback when seating the contacts, which supports quick decision‑making on the shop floor and lowers cycle time for routine checks. Accurate results with carbide measuring faces Equipped with carbide measuring faces, the gauge provides wear resistance where contact durability matters most. The specified accuracy of 0.005 mm positions the instrument for high‑precision internal measurement tasks where sub‑hundred‑micrometre reproducibility is required. This level of accuracy is communicated as a clear, quantifiable benefit: fewer reworks, more reliable acceptance testing and better conformity with drawing tolerances during incoming or in‑process inspections. Adaptable anvils for different bore conditions Interchangeable measuring anvils increase the micrometer’s versatility: the exchangeable heads allow adaptation to varying bore geometries and surface finishes without sacrificing the calibration baseline. For workshops that encounter a range of blind‑hole diameters, the ability to switch measuring faces minimises downtime and reduces the need for multiple dedicated gauges, thereby improving operational efficiency and tool inventory management. Robust, workshop‑ready mechanical design The analogue mechanism with a precise reading increment of 0.005 mm is robust and straightforward to maintain in industrial environments. The solid mechanical construction suits regular use in inspection benches and quality departments where resilience and uncomplicated operation are priorities. The compact feel combined with the instrument’s length makes it practical for ergonomic handling during repeated measurements, supporting consistent measurement practice and traceable results. For precise blind‑hole inspections, contact Metav Werkzeuge to discuss the Three‑Point Internal Micrometer MS908.666 and its interchangeable anvils for seamless integration into existing inspection routines. Technical data Article number: MS908.666 Product type: Three‑point internal micrometer Brand: Metav IndustryLine Facts Measuring range: 175–200 mm Minimum range: 175 mm Maximum range: 200 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 145 mm Operation: Analog Special features Self‑centring three‑point contact Interchangeable measuring anvils Carbide measuring faces Suitable for blind‑hole measurement Mechanical design for workshop use FAQ What measuring range does the instrument cover? The Three‑Point Internal Micrometer MS908.666 from Metav IndustryLine covers a 175–200 mm measuring range. How precise is the three‑point internal micrometer? The gauge delivers an accuracy of 0.005 mm, offering high repeatability for internal bore checks. Can the measuring faces be changed for different bores? Yes, the instrument features interchangeable measuring anvils, allowing adaptation to varying bore geometries without replacing the whole tool. Is the micrometer suitable for blind‑hole measurements? Designed specifically for blind‑hole (sackloch) inspection, the self‑centring three‑point design ensures reliable centring in such applications. What construction ensures long service life in the workshop? The MS908.666 uses carbide measuring faces and a robust analogue mechanism to withstand frequent use in industrial inspection environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20-25mm Three-Point Internal Micrometer Self-Centring, Plastic Case - Metav IndustryLine
Take advantage of the combination of self‑centring, carbide measuring faces and high repeatability for reliable blind‑hole inspection; the compact 20–25 mm range is ideal for fine mechanical and precision engineering tasks. Order the instrument directly via Metav Werkzeuge or request specification advice from our consultants. Three‑point internal micrometer MS908.655 — self‑centring, carbide measuring faces (20–25 mm) by Metav IndustryLine The Three‑point internal micrometer MS908.655 is a self‑centring internal measuring instrument designed for accurate measurement of blind holes in precision engineering and workshop environments, offering an analogue reading with fine resolution for repeatable results Self‑centring three‑point mechanism Carbide measuring faces for wear resistance Measurement accuracy 0.004 mm Compact range 20–25 mm for fine parts Precise blind‑hole measurement with minimal setup The instrument delivers high repeatability through its self‑centring three‑point mechanism, which ensures concentric contact inside blind bores without complex alignment. With a rated accuracy of 0.004 mm and an analogue reading of 0.005 mm, the device is engineered for tasks where micrometre‑level certainty matters; this combination reduces rework and measurement uncertainty in small components. The compact design is especially suited to micro fabrication and precision inspection of housings and bores. Durable contact faces and dependable mechanical operation Carbide contact faces provide excellent wear resistance, maintaining measurement integrity over extended use in workshop conditions. The analogue nonius construction offers tactile feedback preferred in many inspection routines and requires no batteries or electronic interfaces, supporting uninterrupted operation on the shop floor. The included adjustment ring (25) enables straightforward zeroing and fine setting, while the robust build keeps the mechanical play to a minimum for consistent results. Designed for micro‑range quality control and fine parts Classified in the micro range (suitable for 10–100 mm scales), the 20–25 mm span targets small‑format parts such as precision sleeves, bearing bores and microassemblies. Its compact dimensions and precise geometry make it practical for use in bench inspection and in‑process checks where access is restricted. The measuring faces and frame geometry have been selected to balance stiffness and accessibility, ensuring stable measurements even when handling delicate components. Integration into workshop procedures and traceability The analogue three‑point gauge complements digital and traditional inspection tools as part of a consistent metrology chain; repeatable manual results simplify tolerance checks and go/no‑go decisions. Further technical documentation and measurement data are available from Metav Werkzeuge for integration into QA processes and production control. For operators transitioning from standard calipers or bore gauges, the instrument provides a clear step up in concentricity control without introducing complex electronics. For specification advice or to secure the MS908.655 from Metav IndustryLine, contact Metav Werkzeuge for personalised guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.655 Manufacturer: Metav IndustryLine Product: Three‑point internal micrometer Numbers / Core technical data Measuring range: 20–25 mm Reading / resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features / Materials Self‑centring three‑point mechanism Carbide measuring faces Analogue nonius scale Suitable for blind‑hole measurement FAQ What measuring range does the MS908.655 cover? The MS908.655 covers a measuring range of 20–25 mm, making it suitable for small bores and fine mechanical components. How precise is the instrument for repeatable checks? The three‑point internal micrometer achieves a stated accuracy of 0.004 mm with an analogue reading of 0.005 mm, designed for consistent bench and in‑process inspection. Are the measuring faces wear resistant? Yes, the contact faces are made of carbide, providing enhanced wear resistance and long‑term dimensional stability for routine use. Is the gauge suitable for blind‑hole applications? The instrument is explicitly intended for blind‑hole measurement, featuring a self‑centring mechanism that ensures concentric contact within such bores. Does Metav IndustryLine provide technical support for integration into QA procedures? Metav IndustryLine and Metav Werkzeuge can supply further technical documentation and advice to assist with integration of the MS908.655 into quality control workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20-50mm Three-Point Internal Micrometer Self-Centring Set, 4 Pieces in Case - Metav IndustryLine
Take advantage of a self-centring three‑point system together with wear‑resistant carbide measuring faces and a fine 0.005 mm analogue graduation for repeatable blind‑hole measurements. Order the set directly via Metav Werkzeuge or contact our consultants for advice on matching extensions and gauges to specific bores. Three‑point internal micrometer MS908.673 — self‑centring, 0.005 mm analogue The Three‑point internal micrometer MS908.673 is an analogue, self‑centring inside micrometer designed for precise measurement of blind holes in fine mechanical and workshop applications Self‑centring three‑point measuring system Hardmetal measuring faces (carbide) Analogue resolution 0.005 mm Designed for blind‑hole measurement Repeatable centring for reliable results The micrometer’s defining benefit is its self‑centring three‑point head, which aligns reliably in blind bores and reduces off‑axis error during measurement. This design converts operator input into a consistent contact geometry, lowering variance between individual readings and helping to meet process tolerances with fewer rechecks. The analogue graduation with 0.005 mm division gives a clear, immediate view of dimensional changes; when traceable comparability is required, the instrument’s mechanical simplicity supports straightforward in‑house verification routines. Built for longevity and stable contact Measuring faces made from carbide (hardmetal) ensure high wear resistance where repeated contact with bore edges would otherwise round or score softer contacts. The harder contact points preserve nominal diameter and shape over long production runs, translating into lower replacement frequency and a steadier measuring baseline. Where repeatability over time matters for quality control, the combination of robust contact materials and the three‑point geometry yields consistent seating in the bore and predictable measurement behaviour. Practical set composition and extension options Supplied as a set of four, this analogue internal micrometer covers a practical range for precision blind‑hole work and fast gauge changes between nominal sizes. Extensions are available up to 150 mm, enabling larger or deeper bores to be reached without sacrificing centring performance. The instrument is analogue by construction, making it straightforward to use alongside existing mechanical measuring tools; shops that prefer simple, robust gauges will appreciate the minimal maintenance and easy field adjustments afforded by the setting rings. Clear advantages in process environments In repetitive inspection tasks or small‑batch production, the instrument’s self‑centring function reduces operator training time and speeds routine checks. The carbide faces and solid construction lower total cost of ownership by reducing wear‑related drift; together with the fine analogue graduation, these characteristics deliver a balance of durability and measurement fidelity that supports reliable quality control in component manufacture. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine three‑point internal micrometer MS908.673 and available extensions fit into current inspection routines and to request a tailored quotation Technical data Article number: MS908.673 Manufacturer: Metav IndustryLine Category: Messschrauben Measuring principle: Analogue (mechanical) Facts Measuring range: 20–50 mm Reading / graduation: 0.005 mm Pieces per set: 4 Extension option: 150 mm Special features Self‑centring three‑point design Hardmetal (carbide) measuring faces Suitable for blind‑hole measurements Analogue nonius graduation FAQ What measurement range does the instrument cover? The set covers a 20–50 mm measuring range, supplied as a set of four sizes to allow quick changes between nominal diameters. Is the micrometer suitable for blind‑hole bores? Yes — the instrument is explicitly designed for blind‑hole measurements, its three‑point, self‑centring head ensuring reliable seating where standard internal callipers may not centre. What is the smallest readable increment on the scale? The analogue nonius offers a 0.005 mm graduation for fine visual readings and repeatable comparison checks. Are extension rods available for deeper bores? Extension rods up to 150 mm are available to access deeper or recessed bores while maintaining the self‑centring capability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com