200-225mm Three-Point Internal Micrometer Self-Centring, Interchangeable Anvils, Delivered in Case - Metav IndustryLine
Take advantage of the self-centring three-point system and interchangeable measuring insert for reliable blind-hole measurements; combined with carbide measuring faces and an accuracy of ±0.007 mm, this instrument supports consistent quality control. Order the (three-point internal micrometer MS908.667) directly via (Metav Werkzeuge) or ask our consultants if needed. Three-point internal micrometer MS908.667 — self-centring, interchangeable insert The three-point internal micrometer for precise measurement of blind bores in workshop and inspection environments, designed as a mechanical instrument for repeatable internal diameter checks. Self-centring three-point system Interchangeable measuring insert Carbide measuring faces for wear resistance High precision ±0.007 mm Reliable blind-bore measurement with minimal operator influence The three-point system centres automatically within blind bores, reducing alignment errors and giving a reproducible contact geometry; this produces consistent results when inspecting bores. With a reading resolution of 0.005 mm (vernier) and a stated accuracy of ±0.007 mm, the instrument narrows measurement uncertainty to a level suitable for many workshop and production control tasks. The effect is a measurable reduction in rework and faster go/no-go decisions on turning and drilling operations. Durable contact surfaces and easy servicing save time Hard-wearing carbide measuring faces extend service intervals and maintain measurement integrity under repeated use. The measuring insert is exchangeable, which simplifies maintenance and allows quick replacement of worn contacts without discarding the whole instrument. The mechanical construction is straightforward and low-maintenance compared with electronic systems, making it suitable for environments where robustness and simple servicing are priorities. Size and handling tuned to everyday workshop needs Classified in the standard measuring range (measuring range 200–225 mm), this device offers a practical balance of reach and stiffness for typical machine‑shop components such as housings, sleeves and medium-sized bores. The instrument’s overall length of 145 mm supports good accessibility in confined bores while remaining easy to handle during repeated checks. As an analogue instrument with a vernier readout, it performs reliably where electronic readouts are unnecessary or undesired. Confidence for quality control and process stability Intended for routine inspection and in-process checks, the micrometer’s self-centring action and robust contact faces reduce operator-dependent variation and increase throughput in batch inspection. The interchangeable insert concept supports lifecycle planning: wear parts can be stocked and replaced quickly to maintain traceable measurement performance. The device is suitable for blind-hole measurement tasks and integrates well into manual quality-control workflows where mechanical verifiability is required. Contact Metav Werkzeuge today for ordering details and specification advice on the Metav IndustryLine three-point internal micrometer MS908.667 and its spare measuring inserts Technical Data Article number: MS908.667 Manufacturer: Metav IndustryLine Category: Micrometers (internal micrometer) Facts Measuring range: 200–225 mm Reading / Resolution: 0.005 mm Accuracy: ±0.007 mm Overall length: 145 mm Display: analogue (vernier) Features & Delivery Self-centring three-point system Carbide measuring faces Interchangeable measuring insert Designed for blind bores (blind-hole measurement) Mechanical, analogue instrument FAQ How does the three-point centring reduce measurement error? The self-centring three-point mechanism distributes contact forces evenly; the three-point internal micrometer MS908.667 centres itself in the bore to reduce eccentricity and improve repeatability. Can the measuring faces be replaced when worn? Yes — the instrument is fitted with an exchangeable measuring insert, so worn carbide faces can be renewed without replacing the entire micrometer. Is the reading digital or mechanical? The device uses a mechanical vernier readout with a reading resolution of 0.005 mm, offering a robust, electronics-free solution for workshop environments. For which bore types is this instrument intended? It is designed specifically for blind bores; the three-point configuration ensures reliable contact geometry in such applications. What is the measuring range and typical accuracy? The measuring range is 200–225 mm and the stated accuracy is ±0.007 mm, suitable for standard workshop inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
225-240mm Three-Point Internal Micrometer Self-Centering Exchangeable Anvils, Supplied in Case - Metav IndustryLine
Take advantage of self‑centring three‑point measurement and carbide measuring faces for consistent, reproducible results in blind‑hole bores; the interchangeable measuring inserts allow flexible adaptation across the nominal range. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.668 — self‑centring, carbide faces (Metav IndustryLine) The MS908.668 is a three‑point internal micrometer for accurate measurement of blind‑hole bores in workshop and inspection environments. Self‑centring three‑point measuring head Carbide measuring faces for wear resistance Interchangeable measuring inserts Delivered in protective case Faster, repeatable centring in blind‑hole measurement The self‑centring three‑point measuring head significantly reduces setup time when inspecting blind‑hole bores. By contacting the bore with three equidistant measuring points the instrument centres itself automatically, which improves repeatability compared with two‑point probes and speeds up routine checks. The analogue mechanism keeps the operation straightforward for technicians and maintenance staff who require reliable results without complex electronics. Metrology performance you can rely on Designed for industrial use, the instrument offers a stated accuracy 0.007 mm and a resolution 0.005 mm, values that make it well suited for quality control in machining and assembly. These specifications mean the device detects small deviations while providing a clear mechanical indication of the measurement. The combination of robust mechanical gearing and a clear, fine graduation supports precise readings under standard workshop conditions, helping to maintain product tolerances and reduce the risk of costly rework. Durable contact surfaces and flexible inserts The measuring faces are carbide tipped to resist wear during frequent use, preserving the nominal geometry and ensuring long‑term stability. Interchangeable measuring inserts permit adaptation across the stated measuring span so one instrument can cover a range of bore diameters without compromising accuracy. Supplied in a protective case, the tool is ready for transport to the machine or for storage in an inspection cabinet, keeping the measuring faces protected between uses. Trusted partner for precision tasks As part of the Metav IndustryLine range, this three‑point internal micrometer benefits from the supplier’s focus on accessibility and reliability. Metav’s approach to precision brings workshop‑grade metrology within reach, backed by a broad product portfolio and proven logistical support from Emmerich. The instrument suits metrology labs, maintenance teams and production lines that prioritise consistent centring, wear resistance and straightforward operation. For expert advice or to purchase the Metav IndustryLine three‑point internal micrometer MS908.668 with interchangeable inserts and carbide faces, please contact Metav Werkzeuge for tailored assistance and fast supply Technical data Article number: MS908.668 Brand: Metav IndustryLine Category: Messschrauben Numbers / Facts Measuring range: 225–240 mm Resolution (reading): 0.005 mm Accuracy: 0.007 mm Length: 145 mm Analogue instrument Special features / Versions Self‑centring three‑point measuring head Carbide measuring faces Interchangeable measuring inserts Suitable for blind‑hole bores Supplied in protective case FAQ What measuring range does the instrument cover? The MS908.668 three‑point internal micrometer covers a measuring span from 225 mm to 240 mm as delivered. Is this tool suitable for blind‑hole measurements? Yes; the three‑point, self‑centring design is specifically intended for reliable measurement of blind‑hole bores. Can the measuring inserts be replaced to adjust for different bore sizes? Interchangeable measuring inserts are provided, allowing the instrument to be adapted across its nominal measuring span. How precise are the readings from this analogue instrument? The instrument provides a resolution of 0.005 mm with a stated accuracy of 0.007 mm, suitable for workshop and production quality checks. Are the measuring faces durable under regular workshop use? The contact points are carbide tipped to increase wear resistance and maintain geometric integrity over extended use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25-30mm Three-Point Internal Micrometer Self-Centering, 0.004mm Accuracy, Supplied in Case - Metav IndustryLine
Take advantage of the combination of precise 0.004 mm accuracy, a self‑centring three‑point measuring head and carbide measuring faces for consistent blind‑hole measurement; order directly via Metav Werkzeuge or contact the consultancy team for tailored advice. MS908.656 Three‑Point Internal Micrometer — Self‑centring, 25–30 mm range (Metav IndustryLine) A three‑point internal micrometer designed for accurate measurement of blind holes and restricted bores in the 25–30 mm range, combining a compact form with stable contact geometry. Three‑point self‑centring measuring head Measuring range 25–30 mm Carbide measuring faces for wear resistance Analogue drive with 0.005 mm resolution Consistent results for blind‑hole inspection The instrument's self‑centring three‑point system guarantees repeatable contact with bore surfaces, reducing setup variance and rework in production inspection. The compact contact geometry suits restricted bores where standard callipers cannot reach, while the analogue drive and fine spindle allow controlled approach to the measuring surfaces. This configuration translates directly into fewer rejected parts and more reliable pass/fail decisions on the shop floor. Precision that meets workshop demands With a documented accuracy of 0.004 mm and a readable resolution of 0.005 mm, the device sits between general workshop tools and high‑precision instruments. The mechanical design and robust spindle ensure stable readings even in routine quality control. For applications that require exact internal diameters in small assemblies, this micrometer provides a balance of sensitivity and practical handling without invoking complex electronic systems. Durable contact surfaces for long service life The measuring faces are made from carbide, offering superior wear resistance under frequent use and abrasive conditions. That hard contact material preserves the reference geometry over many cycles and keeps measurement uncertainty low. An adjustment ring marked 25 assists with quick reference when setting or checking the nominal diameter, making repetitive tasks more efficient and less error‑prone. Compact format for fine mechanical work Classified in the micro range by its 25–30 mm span, the tool is ideal where small, precise components are involved. The short overall length supports handling in confined environments and maintains torsional stiffness for reliable contact pressure. As an analogue internal measuring instrument, it offers familiar operation for technicians while delivering the benefits of a three‑point system designed specifically for blind‑hole measurement. For precise and repeatable blind‑hole measurement, contact Metav Werkzeuge to request the Metav IndustryLine three‑point internal micrometer MS908.656 or to speak with a specialist at info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: MS908.656 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Facts Measuring range: 25–30 mm Resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features Self‑centring three‑point measuring head Carbide measuring faces Analogue micrometer design Adjustment ring marked 25 Suitable for blind‑hole measurement FAQ What measuring range does this instrument cover? The three‑point internal micrometer MS908.656 covers a measuring range of 25–30 mm, suited to small‑bore and blind‑hole applications. Is this micrometer suitable for blind‑hole measurement? Yes, the self‑centring three‑point system of the Metav IndustryLine three‑point internal micrometer is specifically designed to measure blind holes and restricted bores reliably. What accuracy and resolution can be expected? The instrument provides an accuracy of 0.004 mm with an analogue readable resolution of 0.005 mm, offering precise control for workshop inspections. Are the measuring faces durable for repeated use? The measuring faces are made of carbide, ensuring wear resistance and long‑term stability of the contact geometry under frequent measurement cycles. How is the instrument adjusted for repetitive tasks? An adjustment ring marked 25 is provided for quick reference and repeatable setting when working with the same nominal diameters. Is this a digital instrument? No, the MS908.656 is an analogue internal micrometer, combining mechanical reliability with a fine spindle for controlled readings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25-50mm Digital Bore Gauge Colour 2.4" Touchscreen, Wireless USB, IP65 - Microtech Metrology
Take advantage of the micrometer’s combination of high repeatability (0.004 mm), wireless and USB data transfer, and robust IP65 protection to speed up inspection routines and reduce documentation errors. Order via Metav Werkzeuge or consult the specialists for integration into existing quality workflows. Digital Micrometer 25–50 mm — Microtech Metrology, 2.4" touchscreen, Wireless+USB The Digital Micrometer 25–50 mm is a compact, workshop-ready measuring instrument designed for precise external measurements of small components in production and inspection environments. High precision 0.004 mm accuracy Wireless and USB data output Colour 2.4" touchscreen display IP65 dust and splash protection Ø12 mm measuring faces Consistent precision for fine mechanical parts The instrument delivers 0.004 mm stated accuracy with a display resolution of 0.0001 mm, making it suitable for demanding small-part measurement. This level of control reduces uncertainty when checking turned parts, shafts or precision pins: the tighter accuracy ensures fewer borderline results while the fine resolution allows operators to detect small trends in process drift. As a member of the Micro class, the device is optimised for short-range, high-stability measurement where the short spindle and compact frame minimise bending and handling errors. Streamlined data capture for industry workflows Equipped with Wireless+USB outputs and a responsive 2.4" colour touchscreen, the device supports rapid, low-effort data transfer to quality software and SPC systems, cutting manual transcription time and error rates. The digital interface presents readings clearly and the connectivity options allow both direct logging and integration into inspection stations. These features translate into measurable efficiency gains: fewer manual entries, faster batch checks and a more auditable trace of measurement results. Robust construction for everyday shop use The micrometer is rated IP65, so the electronics are protected against dust ingress and low-pressure water jets — a practical advantage at busy benches or on shop floors. The Ø12 mm measuring faces provide a stable contact area for repeatable measurements across small diameters while the compact form factor supports single-handed operation and swift part handling. Built-in durability combined with clear display feedback reduces rework and downtime in standard production and maintenance tasks. Practical benefits and implementation considerations Beyond the core metrological performance, the device assists with traceability and laboratory-to-shop transferability of measurement data thanks to the digital outputs and standardised reading format. The compact nature of the instrument makes it particularly useful for inspection of micro-series, tooling checks and in-cabinet measurements where space is limited. Integration into existing quality processes is eased by common data interfaces and clear numeric output, enabling faster decision loops in fabrication and assembly. For procurement or process-integration advice, contact Metav Werkzeuge to secure the Microtech Metrology digital micrometer with Wireless+USB outputs and discuss options for delivery and calibration support. Technical data SKU: 133800508 GTIN: 4061905458132 eClass: 21170328 Manufacturer: Microtech Metrology Core specifications Measuring range: 25–50 mm Accuracy: 0.004 mm Resolution (reading): 0.0001 mm Measuring faces diameter: Ø12 mm Display: Colour 2.4" touchscreen Protection rating: IP65 Features Data output: Wireless + USB Digital measuring device Category: Micro class micrometer Compact, workshop-suitable construction FAQ What measuring range does the micrometer cover? The micrometer covers a measuring range of 25–50 mm, suitable for small components and precision checks. What accuracy and resolution are specified? The instrument specifies an accuracy of 0.004 mm and a display resolution of 0.0001 mm, enabling fine discrimination in inspection tasks. How can measurement data be exported? Measurement data can be exported via Wireless and USB interfaces, allowing straightforward transfer to inspection software or data loggers. Is the device suitable for harsh workshop conditions? Yes. With an IP65 rating and robust measuring faces (Ø12 mm), the instrument resists dust ingress and splash exposure encountered on production floors. Does the product include a calibration certificate? The product data does not specify an included calibration certificate; calibration options should be checked with the supplier or Metav Werkzeuge if a traceable certificate is required. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
25.4mm Digital Indicator Colour 2.4" Touchscreen Wireless USB Modbus PLC Connection, 0.002mm Accuracy - Microtech Metrology
Take advantage of a compact measuring solution that combines 0–25.4 mm measuring range, 0.002 mm accuracy and flexible data transfer for streamlined quality control. Order the instrument directly via Metav Werkzeuge or consult the Metav team for integration advice. Microtech digital indicator (dial gauge) — 0–25.4 mm range, 2.4‑inch colour touchscreen The digital indicator from Microtech Metrology offers precise linear measurement for inspection tasks and process control in workshops and production environments. 0–25.4 mm measuring range 0.002 mm accuracy 2.4″ colour touchscreen display Wireless and USB data output Consistent high‑precision measurement for quality control This compact digital indicator delivers a 0.002 mm accuracy across a 0–25.4 mm measuring range, providing the reliability required for dimensional spot checks and first‑piece inspection. The specified accuracy describes the instrument’s typical deviation under normal conditions, which helps to reduce uncertainty when comparing parts or validating production steps. The clear numeric readout combined with a fine display increment 0.0001 supports precise decisions without repeated manual interpretation, so measurement records become a dependable basis for quality documentation. Seamless data capture and straightforward integration Equipped with Wireless and USB outputs and a 2.4‑inch touchscreen, the indicator enables rapid transfer of measurement results into statistical process control and traceability systems. The wireless option simplifies temporary setups or mobile inspection stations, while USB provides a direct, stable connection for workbench logging. The touchscreen speeds navigation through measurement modes and zeroing functions, reducing handling time and cutting the administrative overhead of manual data transcription. Gentle contact and repeatable probing A measuring force of 0.7–1.2 N balances reliable contact with minimal surface impact, making the device suitable for soft or finished surfaces where indentation must be avoided. Stable probe pressure reduces variability between operators and supports repeatable readings when used for batch checks. The construction emphasises a compact, rigid feel that minimises deflection over short measuring strokes, improving reproducibility in routine inspection work. Practical application scope and workshop benefits Designed for direct use on the shop floor and in inspection benches, this digital dial gauge is well suited to applications such as component acceptance, tool setting and maintenance checks. Its compact format and readable colour display make it useful where space is at a premium but traceable data is required. Metav’s position as a precision partner ensures easy access to advice and regional supply chains, supporting quick replacement or scaling across multiple workstations. Contact Metav Werkzeuge in Emmerich to discuss application requirements or to arrange a tailored delivery and integration plan for this Microtech Metrology digital indicator Technical data Article number: 120139258M GTIN: 4061905453458 Manufacturer: Microtech Metrology Category: Dial indicators Display: Colour 2.4‑inch touchscreen Data output: Wireless + USB Facts Measuring range: 0–25.4 mm Accuracy: 0.002 Display increment: 0.0001 Measuring force: 0.7–1.2 N Special features Digital display Compact, rigid design for short‑stroke repeatability Wireless connectivity for mobile inspection USB port for direct data capture and logging FAQ What measurement accuracy can be expected from this indicator? The digital indicator from Microtech Metrology provides an accuracy of 0.002, suitable for precise workshop inspection and many quality‑control tasks. How are readings transferred to a PC or data system? Measurement values can be transmitted via Wireless or USB, enabling direct logging into SPC software or simple file export for traceability. Is the contact pressure suitable for delicate surfaces? Yes. With a measuring force of 0.7–1.2 N the instrument applies minimal pressure while maintaining reliable contact for repeatable readings. What measuring range does the device cover? The instrument covers a range of 0–25.4 mm, making it ideal for small to medium components and routine dimensional checks. Can the indicator be used for batch inspection on the shop floor? The combination of a clear colour touchscreen, wireless connectivity and compact form factor makes this indicator well suited to shop‑floor batch inspection and spot checks. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
250-275mm Three-Point Internal Micrometer Self-Centring Interchangeable Spindle, 0.007mm Accuracy, Supplied in Case - Metav IndustryLine
Combine reliable self‑centring measurement with a 250–275 mm measuring range and interchangeable measuring inserts for consistent, repeatable bore checks; order the instrument directly via Metav Werkzeuge or consult their specialists for application advice. Three‑point internal micrometer MS908.669 — self‑centring bore micrometer, 250–275 mm (Metav IndustryLine) The Three‑point internal micrometer MS908.669 is a self‑centring bore micrometer designed for precision measurement of blind holes in machining and workshop quality control. Self‑centring three‑point measurement Measuring range 250–275 mm Accuracy ±0.007 mm Interchangeable measuring insert Accurate bore measurement where alignment matters The three‑point design provides a self‑centring contact with the bore, which reduces alignment error and speeds up set‑up when checking blind holes. With a stated accuracy of ±0.007 mm and an analogue reading step of 0.005 mm, the instrument delivers reproducible results for routine quality checks. The mechanical nonius format keeps the workflow straightforward and avoids dependencies on batteries or electronics, supporting continuous shop‑floor operation. Robust construction for workshop use Classified within the standard range for workshop micrometres, the device covers 250–275 mm, a span that balances reach and stiffness for typical machine‑shop components. The measuring faces are made of carbide, improving wear resistance when probing machined bores. The interchangeable measuring insert system allows quick replacement of worn or specialised tips, extending the instrument’s service life and adapting it to specific bore geometries. Practical handling to reduce cycle time Designed for efficient operation, the instrument’s three‑point geometry centres itself in the bore and thus shortens measurement cycles compared with multi‑step setups. The analogue format is tactile and direct, providing immediate feedback during measurement. Supplied in a protective case for secure transport, the tool is ready for use at different workstations and is dimensioned to be handled easily by one operator for most inspection tasks. Reliable data for consistent quality control Used within a production or inspection routine, the micrometer supports fast go/no‑go decisions and reduces rework by providing consistent internal diameter readings. The combination of a defined measuring range, carbide contact faces and an exchangeable insert system means fewer interruptions for maintenance and predictable measurement behaviour over time. The instrument is especially well suited to blind‑hole verification in component production, jig making and fitting operations. Contact Metav Werkzeuge today to discuss how the MS908.669 can be integrated into existing inspection routines or to arrange a tailored measurement solution from their Emmerich facility Technical data Article number: MS908.669 Product type: Three‑point internal micrometer Brand: Metav IndustryLine Facts Measuring range: 250–275 mm Measuring range (min): 250 mm Measuring range (max): 275 mm Accuracy: ±0.007 mm Reading increment: 0.005 mm Length: 145 mm Special features Self‑centring three‑point measurement Carbide measuring faces Interchangeable measuring insert Suitable for blind‑hole bores Supplied in protective case Analogue mechanical instrument FAQ What measuring range does the instrument cover? The instrument covers a measuring range of 250–275 mm, intended for medium‑sized bores in workshop use. Is the device suitable for blind‑hole measurements? Yes, the three‑point, self‑centring geometry is specifically designed for reliable measurement of blind holes. What accuracy and resolution can be expected? The micrometer offers an accuracy of ±0.007 mm with an analogue reading increment of 0.005 mm. Can the measuring faces be replaced or adapted? The instrument features an interchangeable measuring insert, and the measuring faces are carbide for long service life. How is the product delivered and how is it identified? The tool is supplied in a protective case and is listed as MS908.669 from Metav IndustryLine Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25mm Digital Indicator 0.01mm Resolution Absolute System 330° Rotating Display IP54 - Metav IndustryLine
Combine high-resolution measurement, a rotatable absolute display and robust ingress protection to secure consistent inspection results in production and inspection routines. Benefit from 0.01 mm resolution, 0.005 mm repeatability and IP54 protection for dependable reads. Order the Digital Indicator M301.032 directly via Metav Werkzeuge or ask our consultants if needed. Digital Indicator M301.032 – 25 mm range, 0.01 mm resolution (Metav IndustryLine) A Digital Indicator M301.032 designed for precise linear displacement measurement in workshop inspection and assembly tasks, featuring an absolute measurement system and a display that rotates through 330° for flexible mounting. 25 mm range, 0.01 mm resolution Absolute measurement system Display rotatable by 330° IP54 splash protection Precise measurement for reliable quality control The indicator delivers 0.01 mm resolution with a documented repeatability of 0.005 mm, enabling reliable detection of small deviations during routine checks. The measuring force of >1.5 N minimises bounce and ensures stable contact with workpieces, while the absolute measurement system (3 V supply) preserves reference values after power cycles so readings remain immediately comparable. These characteristics support faster decision-making in inspection, where reproducible data reduces rework and conveyor stoppages. Flexible handling and integration to suit workshop setups A 330° rotatable display allows ergonomic placement on stands or fixtures, keeping the readout visible in tight set-ups. The digital interface includes ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/Inch and ± keys for quick mode changes, and an RB 6 data output for direct capture of measurement results into inspection software or SPC systems. The scale uses a glass guide for improved scanning accuracy and the housing rated IP54 resists splash and dust in demanding environments, extending service intervals and uptime. Practical application and compatibility across tasks Engineered for routine shop-floor inspection, fixture verification and assembly checks, the instrument suits both manual gauges and semi-automated test stations where tight tolerances matter. The compact design and lightweight construction (0.29 kg) mean easy repositioning between stations with minimal fixture change time. Compatibility with common measurement procedures and the comprehensive display modes make the indicator a versatile tool for machinists, quality engineers and metrology labs seeking stable, traceable results. For reliable high-resolution inspection and straightforward data capture, choose the Metav IndustryLine M301.032 and contact Metav Werkzeuge for specification support or purchasing from Emmerich. Technical data Article number: M301.032 GTIN: 4054469158365 Manufacturer: Metav IndustryLine Facts Measuring range: 0–25 mm Resolution: 0.01 mm Repeatability: 0.005 mm Measuring force: >1.5 N Weight: 0.29 kg Protection class: IP54 Measuring system: Absolute with 3 V Special features Display rotatable 0–330° Digital functions: ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/Inch, ± Data output: RB 6 Scale with glass guide for improved scanning accuracy Robust housing suitable for workshop environments FAQ What accuracy can be expected from this indicator? The M301.032 achieves a resolution of 0.01 mm with a repeatability of 0.005 mm, providing the precision needed for standard workshop and inspection tasks. Is the display readable in awkward positions? Yes; the display rotates through 330°, allowing flexible mounting and clear visibility in confined or unusual orientations. Can measurement data be exported to a PC or SPC system? Measurement values can be transmitted via the RB 6 data output, enabling integration into data collection or SPC workflows. Is the indicator suitable for use on the shop floor? With an IP54 protection rating and a robust housing, the indicator is designed to withstand typical shop-floor conditions while maintaining measurement stability. Which measurement modes are available on the display? The digital readout provides ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/Inch conversion and ± functions for versatile measurement workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25mm Digital Indicator Absolute System Rotary Display 0–330° IP54 - Metav IndustryLine
Take advantage of the combination of high-resolution measurement, a rotatable display and robust IP54 protection to keep inspection work fast and reliable; order the gauge directly via Metav Werkzeuge or consult the team for application support. Metav IndustryLine Digital Indicator M301.038 — 25 mm range, 0.001 mm resolution, 330° rotatable display The Metav IndustryLine Digital Indicator M301.038 is a compact, workshop-ready measuring instrument designed for precise short-range inspection and bench-level quality control in machine shops and inspection stations. 25 mm range with 0.001 mm resolution Absolute measuring system with 3 V battery Display rotatable 0–330° for flexible reading IP54 protection for workshop use Accurate short-range inspection that reduces rework The instrument provides a 25 mm measuring range with a fine 0.001 mm display resolution, delivering measurement detail that supports tight tolerance checks on small components. Its repeatability of 0.004 mm ensures consistent results across repeated measurements, which reduces the risk of rejecting correctly manufactured parts or missing out-of-tolerance items. The absolute measuring system preserves the reference position after battery changes, eliminating zero-point drift and shortening setup time for repetitive inspection tasks. Built for everyday workshop conditions A robust enclosure with IP54 protection and a rotatable 0–330° display keeps readings legible in constrained setups and under light contamination. The device’s scale is equipped with a glass slide to support accurate scanning of the encoder, improving signal stability during measurements. The construction and the specified measurement force (>1.5 N) give a reliable sensing action that balances contact stability with component safety, making the gauge suitable for routine shop-floor use and quality control benches. Flexible digital functions and data handling The indicator’s electronic interface includes ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/inch and +/– functions to adapt quickly to diverse inspection procedures and drawing specifications. Power is supplied by a 3 V battery and the instrument offers a data output: RB 6, facilitating integration with downstream data collection or SPC systems where this connector and protocol are supported. These features streamline logging and analysis, so measurement evidence can be consolidated without manual transcription. Practical delivery and typical applications Delivered complete in a transport case, the unit is prepared for secure storage and safe dispatch to job sites. At just 0.29 kg, the gauge is easy to handle for repetitive tasks such as runout checks, small-part height control, or setup verification on fixtures. The combination of compact size, precise resolution and workshop protection makes it well suited for small-part inspection, assembly control and quality assurance processes where fast, reproducible measurements matter. For reliable precision measurement and application advice, contact Metav Werkzeuge in Emmerich—the Metav IndustryLine specialists will assist with selection, technical details and order handling: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: M301.038 GTIN: 4054469163840 ECLASS: 21170308 ETIM: EC003591 Facts Measuring range: 0–25 mm Resolution (display): 0.001 mm Repeatability / Accuracy: 0.004 mm Weight: 0.29 kg Protection class: IP54 Special features Absolute measuring system Display rotatable 0–330° Measurement force: >1.5 N Power: 3 V battery Data output: RB 6 Digital functions: ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/inch, +/– Scale with glass slide for precise scanning Delivered in plastic/wooden case FAQ Is the indicator suitable for routine workshop use? The Metav IndustryLine digital indicator M301.038 is designed for workshop conditions with IP54 protection, a robust enclosure and a rotatable display for ergonomic reading. What data output options are available? This indicator provides a data output: RB 6, enabling connection to compatible data acquisition or SPC devices where the RB 6 interface is supported. How precise is the measurement and how repeatable are results? The device displays 0.001 mm resolution with a repeatability/accuracy listed as 0.004 mm, making it suitable for precise short-range inspection tasks. Does the instrument require calibration on delivery? The product is supplied ready for use and comes with the features specified; calibration status or certificates are provided only if stated separately in the product labelling or order documentation. Which measurement functions are integrated in the display? Integrated functions include ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/inch selection and +/– for offset and tolerance checks. Is the display orientation adjustable for awkward setups? Yes, the rotatable 0–330° display allows flexible positioning so readings remain visible in confined or rotated setups. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
275-300mm Three-Point Internal Micrometer Self-Centring, Interchangeable Anvils, Calibrated in Plastic Case - Metav IndustryLine
Take advantage of a self‑centring three‑point measuring head, robust carbide measuring faces and a 275–300 mm range for consistent blind‑hole inspection — order the instrument via Metav Werkzeuge or contact our specialists for application advice. Three‑point internal micrometer MS908.670 — self‑centring, 275–300 mm range (Metav IndustryLine) The Three‑point internal micrometer is a precision analogue instrument for reliable measurement of blind bores in machine construction and toolmaking. Self‑centring three‑point head Measuring range 275–300 mm Interchangeable measuring insert Resolution 0.005 mm, accuracy ±0.007 mm Consistent centring for blind‑hole work that saves time The instrument’s self‑centring three‑point head guarantees that the measuring contacts align automatically with the bore axis, reducing setup time and minimising operator error. For applications in production or quality control where repeatability matters, this design converts manual handling into a reproducible process. The unit’s standard range (275–300 mm) fits typical medium‑sized bores encountered in fixtures, housings and component assemblies, providing an efficient balance between reach and ease of handling. Clear analogue reading with industry‑grade precision Equipped with an analogue graduation that offers a resolution of 0.005 mm and a stated accuracy of ±0.007 mm, the device provides measurable certainty without complex electronics. These specifications correspond with workshop inspection needs where a tactile feel and immediate visual feedback are valued. In practice, the resolution allows fine incremental control during measurement and the accuracy ensures confidence when recording results for process control or acceptance tasks. Durable measuring faces and modular inserts for long service life The measuring contacts are furnished with carbide measuring faces, chosen for wear resistance and stable contact geometry under repeated use. The interchangeable measuring insert system permits adaptation to varying bore conditions and simplifies maintenance: inserts can be replaced without extensive downtime, extending the instrument’s operational life and keeping measurement uncertainty low. This modularity supports varied production demands while lowering total cost of ownership. Workshop‑ready design tailored to machine‑shop workflows Built as an analogue micrometer in the Metav IndustryLine, the instrument combines straightforward handling with workshop robustness. A compact overall form (length approx. 145 mm) and a three‑point contact principle help to maintain stiffness during measurement, which is crucial when inspecting bores that require high concentricity. The tool is well suited for standard quality control loops and for technicians who prefer a mechanical measuring instrument with clear physical feedback. For expert specification and rapid procurement of the Metav IndustryLine three‑point internal micrometer MS908.670, contact Metav Werkzeuge for tailored advice and to arrange purchase through our European distribution. Technical data Article number: MS908.670 Name: Three‑point internal micrometer Brand: Metav IndustryLine Measuring range: 275–300 mm Length: 145 mm Reading: 0.005 mm Accuracy: ±0.007 mm Self‑centring three‑point head Interchangeable measuring insert Carbide measuring faces Analogue instrument Suitable for blind bores FAQ What bores is this micrometer intended for? The three‑point internal micrometer MS908.670 is designed for blind‑hole measurement and is optimised for bores within the 275–300 mm range. How precise is the measurement result? The instrument provides a resolution of 0.005 mm and an accuracy of ±0.007 mm, allowing dependable readings for workshop inspection and process control. Can the measuring contacts be replaced? Yes. The device features an interchangeable measuring insert system so contacts can be swapped to suit different bore conditions or renewed after wear. Are the measuring faces durable for high batch usage? The micrometer is fitted with carbide measuring faces, offering wear resistance and long service life under repetitive measurement cycles. Who manufactures the instrument and what is the model reference? The product is supplied under Metav IndustryLine as the three‑point internal micrometer MS908.670 and is distributed by Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
30-40mm Three-Point Internal Micrometer Self-Centering, Supplied in Case - Metav IndustryLine
Take advantage of the combination of compact, workshop‑grade precision and robust design for repeatable blind‑hole measurement; the self‑centring three‑point contact and hardened measuring faces deliver reliable results across production and maintenance tasks. Order the instrument directly via Metav Werkzeuge or consult our advisors for application guidance. Three‑point internal micrometer MS908.657 (Metav IndustryLine) — Self‑centring, 30–40 mm The Three‑point internal micrometer MS908.657 is a mechanically driven measuring instrument intended for precise internal diameter checks, especially blind‑hole applications in fine mechanical and light industrial environments. Self‑centring three‑point contact system Measurement range 30–40 mm Hardened measuring faces for durability Precision designed for blind‑hole measurement The three‑point geometry provides self‑centring contact inside blind holes, ensuring that the contact points align automatically with the bore axis and thereby reduce eccentricity errors. With an accuracy of ±0.004 mm and a mechanical reading of 0.005 mm, this analogue measuring instrument translates fine thread motion into dependable metrology results without electronic dependence. The three‑point contact method also helps to average minor surface irregularities, which can reduce rework and speed up routine inspection tasks, making it suitable for both small series production and maintenance checks. Compact format for fine mechanical work Classified in the Mikro range (measurement span up to 100 mm), the instrument’s 30–40 mm span and overall length of 97 mm offer a favourable balance between reach and stiffness. This makes the device well suited to precision tasks where space is limited, such as watch and instrument repair, small housings and insert fittings. The hardened measuring faces increase wear resistance and preserve measurement consistency over long service intervals, so that calibration intervals remain predictable and downtime is minimised. Workshop‑ready robustness and simple handling The analogue design emphasises mechanical reliability: a clear adjustment ring (setting ring 40) allows quick pre‑setting and repeatable contact positioning, while the compact construction withstands everyday workshop handling. Delivered in a protective case for transport, the micrometer is prepared for secure storage and movement between benches or sites. The instrument’s straightforward operation and sturdy build lower the barrier to consistent metrology in production, inspection and maintenance workflows while keeping measurement practice transparent and traceable. Contact Metav Werkzeuge today for tailored application advice on the Metav IndustryLine Three‑point internal micrometer MS908.657 and ensure the right fit for blind‑hole inspection in your workshop Technical data Article number: MS908.657 Manufacturer: Metav IndustryLine Product type: Three‑point internal micrometer Suitable for: Blind‑hole measurement Core data Measurement range: 30–40 mm Length: 97 mm Accuracy: ±0.004 mm Reading (resolution): 0.005 mm Adjustment ring: 40 Mechanical type: Analogue Special features Self‑centring three‑point contact Hardened measuring faces Delivered in protective case for transport Suited to fine mechanical and light industrial use FAQ What makes the three‑point contact better for blind holes? The three‑point geometry centres itself in the bore and averages contact positions; the MS908.657 uses this principle to reduce eccentricity and provide stable internal diameter readings for blind‑hole applications. What accuracy and resolution can be expected from this instrument? The instrument offers an accuracy of ±0.004 mm with a mechanical reading of 0.005 mm, giving precise analogue measurement suitable for production checks and workshop inspection. Is the device suitable for watchmaking and small parts? Yes. With its compact dimensions and classification in the Mikro range, the micrometer is well adapted to fine mechanical work, small housings and components where a short, stiff measuring span is required. Are the measuring faces wear‑resistant? The micrometer is supplied with hardened measuring faces, which increases durability and helps maintain measurement consistency over extended use. Does the delivery include a protective case? The instrument is supplied in a protective case for transport and secure storage, making it straightforward to move between benches or sites. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.5 mm Hand Lever For Dial Gauges Reduces Max Range By 5mm - Metav IndustryLine
Taking advantage of a compact, purpose-built actuator that fits dial gauges with a 4.5 mm measuring pin, this lever delivers repeatable actuation while remaining extremely lightweight; note that the maximum measuring range is reduced by 5 mm when the lever is used. Order accessories or request tailored advice directly via Metav Werkzeuge. Hand lever for dial gauges M208.000 — 4.5 mm pin compatibility, lightweight accessory (Metav IndustryLine) The Hand lever for dial gauges M208.000 is a compact, bolt‑on accessory for actuating dial indicators that use a 4.5 mm measuring pin, suited to workshop and bench inspection tasks. For dial gauges with 4.5 mm pin Reduces measuring range by 5 mm when used Extremely lightweight at 0.04 kg Simple bolt-on attachment for quick setup Repeatable actuation for consistent gauge readings The lever is engineered to provide a consistent actuation path for dial indicators, reducing variability caused by manual finger pressure. By fitting to dial indicators with a 4.5 mm measuring pin, the device turns intermittent manual probing into a steady mechanical action, which supports more reliable comparative measurements during series checks. The built‑in mechanical interface is designed to keep inertia to a minimum thanks to an extremely low mass of 0.04 kg, so the impact on the instrument’s dynamics is negligible while actuation remains crisp and controllable. Practical mounting and application benefits The accessory installs as a bolt‑on, quick‑fit lever, enabling fast retrofitting to existing gauges without the need for additional brackets or complex fixtures. In production or test benches where multiple checks are performed, the lever shortens handling times and improves throughput by standardising the actuation movement. A key operating note: the maximum measuring range is shortened by 5 mm when the lever is engaged, which should be considered when planning inspection sequences to ensure the remaining travel meets tolerance requirements. The simple mechanical design avoids electronic interfaces, resulting in a maintenance‑friendly solution for repetitive gauge tasks. A compact accessory backed by a trusted precision partner As a compact accessory from Metav IndustryLine, the lever complements a pragmatic approach to workshop measurement: small, effective adaptations that increase process stability without overcomplicating setups. The accessory is classified as a gauge lever and is intended for routine use in machine shops, maintenance bays and inspection benches where dial indicators are already in service. For organisations consolidating tooling and measurement supplies, this lever is a low‑investment way to raise repeatability across manual checks while relying on the logistics and quality filters maintained by Metav Werkzeuge. Contact Metav Werkzeuge for specification matching or to reserve the M208.000 — call +49 2822 7131930 or email info@metav-werkzeuge.com for prompt advice and supply from Emmerich Technical data Article number: M208.000 GTIN: 4054469181387 Weight: 0.04 kg Category: Messgeräte > Messuhr Facts Bolt / pin diameter: 4.5 mm Maximum measuring range reduced by: 5 mm Weight: 0.04 kg Special features Suitable for dial indicators with 4.5 mm measuring pin Quick bolt‑on fixing for simple installation Extremely low mass for minimal inertia Accessory type: hand lever for dial gauges FAQ Is this lever compatible with standard dial indicators? Compatibility is given for dial indicators that use a 4.5 mm measuring pin; the lever is designed specifically for that interface and provides a reliable mechanical actuation. Does the lever affect the available measuring travel? Yes — when the lever is used, the maximum measuring range is reduced by 5 mm; this limitation is intrinsic to the actuation geometry and should be considered in measurement planning. How is the lever attached and is the M208.000 easy to retrofit? The lever mounts by a simple bolt‑on fix to the gauge pin and was developed for quick retrofitting to existing setups, enabling rapid deployment without additional fixtures. Is the accessory suitable for repetitive production checks? Its low mass and consistent actuation make the lever suitable for repetitive series checks and bench inspection workflows where standardised probe movement improves repeatability. Which SKU identifies this product for ordering? The lever is listed as M208.000 and is supplied as an accessory for dial gauges; the SKU may be referenced when requesting availability from Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40-50mm Three-Point Internal Micrometer Self-Centring, Precision 0.005mm, Supplied in Case - Metav IndustryLine
Benefit from the combination of self‑centring three‑point contact, 0.005 mm accuracy and carbide measuring faces to secure reproducible blind‑hole measurements; order the MS908.658 directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.658 — self‑centring, 40–50 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.658 is a self‑centring, analogue instrument intended for precision measurement of blind holes and internal bores in small to medium components, offering a compact solution for fine mechanical and toolmaking tasks. Self‑centring three‑point measurement High precision: 0.005 mm accuracy Carbide measuring faces for durability Measuring range 40–50 mm for blind holes Reliable accuracy for critical fits and assemblies The MS908.658 delivers a resolution of 0.005 mm with a matching accuracy of 0.005 mm, providing measurable repeatability for tolerance‑sensitive internal features. The finely graduated analogue scale suits production and workshop environments where a tactile, immediate reading is preferred over electronic systems. This level of precision reduces rework and inspection time by supplying a clear, verifiable measurement result that supports quality control routines and efficient process decisions. Compact, micro‑range design that reduces handling error Classified in the micro range (max. 10–100 mm), the instrument’s 40–50 mm span targets finely detailed components such as small housings, inserts and precision sleeves. The self‑centring mechanism with three‑point contact automatically aligns the measuring faces within a bore, lowering sensitivity to off‑axis entry and operator variance. The compact form factor and balanced length make single‑handed operation straightforward, improving throughput where frequent in‑process checks are required. Durable measuring faces for long‑term repeatability Equipped with carbide (hardmetal) measuring faces, the micrometer resists wear and maintains measurement integrity across extended use. Carbide tips provide a hard, stable contact surface that minimises surface damage to workpieces while preserving repeatable reference points. For workshops seeking a robust, low‑maintenance gauge, this construction ensures a consistent lifecycle performance and contributes to lower total cost of ownership over time. Practical handling, calibration and typical applications The instrument is analogue and supplied with a setting ring at 40 mm to simplify zeroing and quick verification before series checks. Its total length of 97 mm facilitates access to compact bores while keeping the device rigid during measurement. Typical applications include blind‑hole inspection in toolmaking, component verification in precision engineering and quick fit checks in assembly processes. For specification matching and integration into inspection routines, Metav’s product consultants can assist with selection and measuring technique recommendations. Choose the Metav IndustryLine MS908.658 for reproducible blind‑hole measurement and contact Metav Werkzeuge in Emmerich for tailored technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: MS908.658 Type: Three‑point internal micrometer Brand: Metav IndustryLine Measuring range: 40–50 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm Operation: Analogue Setting ring: 40 Length: 97 mm Facts Measuring range: 40–50 mm Resolution: 0.005 mm Accuracy: ±0.005 mm Length: 97 mm Special features Self‑centring mechanism Three‑point contact for blind‑hole measurement Carbide (hardmetal) measuring faces Suited for fine mechanical and toolmaking applications Analogue scale for immediate readings FAQ What bore sizes can be measured with this instrument? The MS908.658 covers internal dimensions in the 40–50 mm range and is optimised for blind‑hole measurement within that span. How precise is the measurement capability? The instrument offers a resolution of 0.005 mm with an accuracy rated at 0.005 mm, suitable for many tolerance‑sensitive internal checks. Are the measuring faces wear‑resistant? Yes, the MS908.658 is fitted with carbide (hardmetal) measuring faces, which provide superior wear resistance and long‑term repeatability. Is this gauge suitable for production‑line checks? Its compact, analogue design and self‑centring three‑point system make the micrometer well suited to repetitive in‑process inspections and quick verification tasks. Does the micrometer require electronic data output? This model is analogue and does not include electronic data output; it is designed for direct, fast readings on the shop floor. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5-30mm Bore Micrometer With Microcomputer Colour 2.4" Touchscreen, IP65 - Microtech Metrology
Benefit from compact yet robust measurement that combines high repeatability, reliable workshop protection and flexible data transfer for streamlined quality control. The compact 5–30 mm range and 0.004 mm resolution make this instrument ideal where fine tolerances matter. Order the micrometer (Micrometer for internal measurements) directly via (Metav Werkzeuge) or ask our consultants if needed. Micrometer for internal measurements — 2.4‑inch colour touchscreen, Wireless+USB (Microtech Metrology) The micrometer for internal measurements is a compact, high-resolution instrument intended for precision checks of small bores and internal features in workshops and inspection benches. 2.4‑inch colour touchscreen display Wireless and USB data output IP65 protection for workshop conditions 0.004 mm resolution for repeatable readings Fast, repeatable results where accuracy matters The instrument delivers 0.004 mm resolution across a measuring range 5–30 mm, which translates into highly repeatable readings during routine quality checks. The compact measuring faces (Ø2 mm) reduce contact area for confined bores and ensure stable seating inside small features; this minimises measurement scatter and shortens inspection time. Such precision supports process control in small-part assembly and metrological checkpoints, turning single checks into verifiable records suitable for traceable documentation. Built for daily workshop use and harsh environments A IP65 rating provides protection against dust ingress and water jets, so measuring workpieces at the machine or bench is possible without additional shielding. The solid construction and compact form factor place this tool within the micro‑range class of measuring instruments, making it especially suitable for fine mechanical applications such as watchmaking, small hydraulic components or precision fittings. The included setting ring eases zeroing and routine checks, reducing downtime during shift changes and calibration cycles. Digital connectivity that speeds data workflows Equipped with Wireless and USB outputs alongside a 2.4‑inch touchscreen, the unit simplifies transfer of measurement data into inspection software or spreadsheets without manual transcription. The colour touchscreen improves legibility of results and menus, while the dual data channels enable integration into both mobile measuring routines and fixed data-capture stations. This connectivity reduces administrative overhead and supports faster statistical evaluation or SPC input directly from the measurement step. Practical integration and partner support for procurement Compact dimensions and direct data export make this instrument straightforward to fold into an existing inspection process, whether used at the bench or integrated into a quality-control station. Metav’s service network and product range allow procurement of matching accessories and calibration services from a single source, helping to maintain instrument availability and traceability. For purchasers seeking a reliable supplier, this product combines technical suitability with a partner able to support sourcing and aftermarket needs. For specification advice or to arrange supply from Emmerich, contact Metav Werkzeuge about the Microtech Metrology micrometer and discuss integration options with our technical consultants. Technical data Article number: 133800308 GTIN: 4061905457746 Manufacturer: Microtech Metrology Category: Micrometers Digital: Yes Core specifications Measuring range: 5–30 mm Resolution / accuracy: 0.004 mm Measuring faces: Ø2 mm Protection class: IP65 Display: 2.4‑inch colour touchscreen Data output: Wireless + USB Features / Accessories Includes setting ring Colour touchscreen for clear readings Wireless and USB connectivity Compact micro‑range design for small bores Suitable for workshop and inspection use FAQ How precise is the micrometer and what tolerances can it check? The Micrometer (Microtech Metrology, SKU 133800308) provides 0.004 mm resolution, making it suitable for quality checks and dimensional control where sub‑hundred‑micrometre accuracy is required. Is this instrument made for internal measurements only? Yes, the design and Ø2 mm measuring faces are optimised for internal diameter checks and confined bores, enabling stable contact in small features. How is measurement data exported from the device? Data can be exported via Wireless or USB, and the 2.4‑inch touchscreen simplifies on‑device review before transfer into inspection systems or spreadsheets. Can the micrometer be used at the machine or in damp environments? The IP65 protection rating allows use in dusty or splash‑prone workshop conditions, supporting measurement at the production line or next to machining operations. What is included in the delivery? Delivery includes the micrometer, a setting ring for zeroing/verification and standard packaging as supplied by Microtech Metrology. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
50-100mm Three-Point Internal Micrometer Self-Centring, Set of 4, Delivered in Case - Metav IndustryLine
Take advantage of precise internal measurement, robust carbide contact faces and a self-centring three-point design for reproducible results in blind-hole inspection; order directly via Metav Werkzeuge or consult our specialists for application support. Three-point internal micrometer MS908.674 — self-centring, 50–100 mm (Metav IndustryLine) The Three-point internal micrometer MS908.674 is a self-centring, analogue gauge designed for precise measurement of blind holes and internal bores in fine mechanical and workshop environments Three-point internal micrometer for blind holes Self-centring contact ensures consistent alignment Carbide measuring faces for wear resistance Resolution 0.005 mm for fine readings Accurate internal measurement even in blind holes The three-point contact mechanism provides a self-centring measuring action that minimises positional error when measuring blind holes and stepped bores. With an analogue graduation of 0.005 mm, the instrument offers repeatable readings suitable for detailed inspection tasks where sub-0.01 mm differentiation is required. The design converts radial deflection into a centralised reading, reducing user-induced eccentricity and enabling faster measurement cycles compared with single-contact probes. Durable contact faces and stable mechanical construction Carbide-tipped measuring faces give the gauge excellent wear resistance, keeping tolerances stable over extended use in workshop conditions. The mechanical construction prioritises stiffness and low play, which supports reproducible results across multiple measurements. Where surface finish and hardness vary, the robust contact material helps maintain accuracy without frequent rework or adjustment. Complete set and accessories for flexible reach Supplied as a set of four pieces, the package includes setting rings at 62 mm and 87 mm for quick verification and adjustment of the instrument. Extension pieces enabling deeper reach are available up to 150 mm, which allows measurement of recessed or deep blind bores without compromising the centring effect. This combination reduces the need for additional special tooling and speeds up inspection workflows. Designed for precision workbenches and toolrooms Classified in the Micro range with a maximum measuring limit of 100 mm, this gauge is particularly suited to fine mechanics, watchmaking and precision component inspection where compact size and high accuracy are essential. The analogue format preserves a direct, tactile measurement experience favoured in quality control loops, while the three-point geometry and carbide faces address longevity and measurement integrity in regular production use. Contact Metav Werkzeuge for a specification review and to discuss application-matched delivery of the Metav IndustryLine three-point internal micrometer MS908.674, including set contents and available extensions Technical Data Article number: MS908.674 Product: Three-point internal micrometer Brand: Metav IndustryLine Facts Measuring range: 50–100 mm Graduation / reading: 0.005 mm Format: Analogue Set quantity: 4 pieces Extensions available: 150 mm Setting rings: 62 mm, 87 mm Special features Self-centring three-point contact Carbide (hard metal) measuring faces Suitable for blind-hole measurement Ideal for micro-range internal inspection FAQ How does the three-point contact improve measurements? The three-point geometry of the Three-point internal micrometer MS908.674 ensures that the gauge self-centres in the bore, reducing eccentricity and producing more reproducible internal diameter readings than single-contact methods. Is the instrument suitable for blind holes only, or can it measure through-holes too? While optimised for blind-hole inspection, the MS908.674 can also be used for internal measurements in through-holes where the three-point centring and carbide faces remain advantageous. What verification accessories are supplied with the set? The delivered set contains setting rings at 62 mm and 87 mm for rapid verification and adjustment, supporting a straightforward calibration routine before inspection runs. Can the gauge reach deep recesses or stepped bores? Extensions up to 150 mm are available to increase reach; when combined with the self-centring mechanism, these extensions enable accurate measurement of recessed internal features. What level of durability can be expected from the contact faces? The carbide measuring faces are specified for high wear resistance, ensuring long-term dimensional stability under regular workshop use and reducing maintenance intervals. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50-63mm Three-Point Internal Micrometer Self-Centring, Supplied in Case - Metav IndustryLine
Take advantage of a self‑centring three‑point measuring head and a 0.005 mm accuracy across a compact 50–63 mm range for reproducible blind‑bore inspections; order the instrument directly via Metav Werkzeuge or consult the specialists for application advice. Three‑point internal micrometer MS908.659 — Metav IndustryLine, self‑centring, 50–63 mm The Three‑point internal micrometer is a precision instrument designed for accurate measurement of blind bores and other internal diameters within the 50–63 mm range, combining a self‑centring three‑point head with robust analogue mechanics for repeatable results. Self‑centring three‑point measuring head Range 50–63 mm Accuracy 0.005 mm Carbide measuring faces Reproducible internal measurements through self‑centring design The instrument’s self‑centring three‑point measuring head converts small operator variations into consistent contact across the bore, which reduces eccentricity and minimises measurement scatter. With a declared accuracy of 0.005 mm and an analogue readout, this tool offers a clear, verifiable performance baseline that supports process control and reduces rework in production environments. The three‑point geometry is particularly effective on short to medium blind bores, where central alignment is critical to obtain reliable diameter values. Built for workshop use: durable faces and compact handling Equipped with carbide measuring faces, the device resists wear from regular contact with machined surfaces and maintains form integrity during frequent use. The compact overall length of 114 mm and a setting ring of 62 support comfortable handling in workshop and inspection‑bench situations, enabling efficient measurement cycles without sacrificing stiffness. As an analogue instrument, it delivers straightforward operation and low maintenance while providing the tactile feedback many technicians prefer for repeat measurements. Practical benefits for quality assurance and inspection routines Integrating this internal micrometer into quality checks provides a direct improvement to inspection throughput and measurement consistency. The tool is explicitly suitable for blind‑bore applications and mechanical assembly checks, offering a reliable technical solution where calipers or telescoping gauges may be less repeatable. The combination of a robust three‑point head and carbide contact faces translates into fewer measurement-related interruptions and a steadier conformity assessment across batches. Contact Metav Werkzeuge in Emmerich for tailored advice on application and availability of the MS908.659 three‑point internal micrometer Technical data Article number: MS908.659 Product: Three‑point internal micrometer Manufacturer: Metav IndustryLine Numbers / Core technical data Measuring range: 50–63 mm Minimum range: 50 mm Maximum range: 63 mm Reading / resolution: 0.005 mm Accuracy: 0.005 mm Length: 114 mm Setting ring: 62 Special features / Designs Self‑centring three‑point head Carbide (hard‑metal) measuring faces Analogue mechanical operation Suitable for blind bores FAQ What degree of accuracy can be expected from this three‑point internal micrometer? The MS908.659 from Metav IndustryLine delivers an accuracy of 0.005 mm with a 0.005 mm reading increment, suitable for precise workshop inspection tasks. Is this instrument suitable for blind‑bore measurement only? While optimised for blind bores, the three‑point internal micrometer is also applicable to other internal diameter checks where central alignment and repeatability are required. How does the self‑centring feature improve measurement results? The self‑centring three‑point head ensures even contact around the circumference, reducing eccentricity and enabling more reproducible diameter readings during routine inspections. What maintenance is recommended to retain measurement reliability? Regular cleaning of the carbide faces and periodic verification against a calibrated ring gauge will preserve the instrument’s performance; the analogue mechanics favour simple, on‑site care. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50-75mm Micrometer Depth Gauge With Colour Touchscreen, Wireless/USB, IP65 - Microtech Metrology
Take advantage of the combination of reliable ±0.004 mm measurement accuracy, robust IP65 protection and seamless Wireless+USB data transfer for precision tasks in the 50–75 mm range. Order the micrometer directly via Metav Werkzeuge or ask our consultants if needed. Microtech Metrology digital micrometer (50–75 mm) — Colour 2.4" touchscreen & Wireless+USB The Microtech Metrology micrometer is a digital measuring instrument designed for precise workshop and laboratory measurements within the 50–75 mm range, combining a Colour 2.4" touchscreen with protected connectivity for modern data workflows. Colour 2.4" touchscreen display Wireless and USB data output IP65 dust and water protection High accuracy ±0.004 mm Repeatable precision for quality control and inspection The instrument delivers high repeatability with a declared accuracy of ±0.004 mm, making it suitable for routine quality control and dimensional verification in component production. The tight tolerance ensures that inspection results are directly comparable across shifts and measuring sessions, reducing rework and non‑conforming parts. Built-in digital readout avoids manual interpolation errors and speeds up measurement cycles, which supports lean production targets and consistent process control. Modern data handling to streamline documentation Equipped with Wireless+USB data output and a Colour 2.4" touchscreen, the device enables direct transfer of measured values into spreadsheets and SPC systems, eliminating transcription errors and saving administrative time. The clear colour display improves readability in variable lighting, while tactile screen controls simplify menu navigation for common functions. Integration capability with existing data capture workflows facilitates traceable batch documentation and faster reporting for inspection records. Robust design for everyday shopfloor use With a measuring range of 50–75 mm and hardened measuring faces of Ø12 mm, the micrometer is dimensioned for typical workshop components where a balance of reach and rigidity is required. The IP65 protection rating shields electronics from dust and splashes, extending service life in harsher production environments. Ergonomic construction and a concise footprint allow handheld operation for rapid checks at the machine or measuring bench, providing confidence that measured values reflect part geometry rather than handling artefacts. Choose Microtech Metrology’s digital micrometer for precise 0.004 mm measurement and reliable data transfer; contact Metav Werkzeuge in Emmerich for tailored supply and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 133800758 GTIN: 4061905458149 Manufacturer: Microtech Metrology Facts Measuring range: 50–75 mm Accuracy: ±0.004 mm Measuring faces: Ø12 mm Display: Colour 2.4" touchscreen Protection class: IP65 Special features Digital output: Wireless + USB Digital device (electronic readout) Category: Micrometers eClass: 21170328 FAQ What measuring range does this micrometer cover? The micrometer covers a measuring range of 50–75 mm (Microtech Metrology, SKU 133800758), suitable for medium‑sized workshop components. How precise is the device for inspection tasks? Precision is specified as ±0.004 mm for the Microtech Metrology micrometer, making it appropriate for standard quality control and dimensional checks. Which data interfaces are available for logging measurements? Measurement data can be exported via Wireless and USB connections, allowing the micrometer to feed values directly into documentation or SPC systems. Is the micrometer protected against dust and splashes? Yes, the unit carries an IP65 rating, so the electronics and display are protected against dust ingress and water jets typical of workshop environments. What advantages does the touchscreen bring to daily measuring? The Colour 2.4" touchscreen provides improved legibility and intuitive controls, speeding routine measurements and reducing input errors on the Microtech Metrology micrometer. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
50.8mm Digital Indicator With 0.0001mm Resolution Colour Touchscreen, Wireless/USB Output - Microtech Metrology
Take advantage of the combination of 0.003 mm accuracy, a 50.8 mm measuring range and flexible data transfer via Wireless and USB for reliable inline checks and repeatable bench measurements. Order the instrument directly via Metav Werkzeuge or contact our consultants for integration advice. Messuhr — Digital indicator with 2.4" colour touchscreen and Wireless/USB output (Microtech Metrology) The Messuhr is a compact electronic measuring indicator designed for precise displacement measurement in inspection benches and production control environments. *High accuracy 0.003 mm *50.8 mm measuring range for compact parts *2.4" colour touchscreen for intuitive operation *Wireless and USB data output for integration Reduce scrap with laboratory-grade repeatability An accuracy of 0.003 mm delivers measurement certainty where tolerance margins are tight. The instrument’s 50.8 mm measuring range covers small to medium components while keeping a compact footprint suited to quality-control benches. This precision reduces rework and speeds up go/no-go decisions by providing a clear, verifiable measurement result every time. Streamline data collection and process control Equipped with Wireless and USB interfaces, the indicator simplifies transfer of readings into inspection software and traceability systems. Wireless transfer avoids cable clutter on the bench; USB provides a reliable direct link for batch logging. Both options support quick incorporation of measurement data into statistical process control and documentation workflows. Consistent contact and straightforward operation A controlled measuring force of 1.2–2.2 N ensures consistent contact pressure, which limits variability from manual handling and improves repeatability. The 2.4" colour touchscreen presents readings and menus clearly, shortening training time and reducing operator errors. The user interface is designed for swift measurement tasks common in workshop and laboratory routines. Built for workshop inspection and inline quality checks This electronic indicator is a practical choice for component inspection, gauge checks and incoming goods control. The robust digital design combines dependable electronics with easy integration into inspection chains, making it suitable for small series production as well as laboratory applications. Traceable data capture supports quality documentation and audit requirements. Contact Metav Werkzeuge for a technical consultation on integrating this Microtech Metrology digital indicator into existing inspection systems Technical data Article number: 120139508M GTIN: 4061905453465 ECLASS: 21170308 Manufacturer: Microtech Metrology Facts Measuring range: 0–50.8 mm Accuracy: 0.003 mm Measuring force: 1.2–2.2 N Display size: 2.4" colour touchscreen Special features Digital indicator (electronic) Wireless + USB data output Colour 2.4" touchscreen Digital display FAQ What level of precision can be expected from this instrument? The Messuhr from Microtech Metrology provides an accuracy of 0.003 mm, suitable for high-precision bench measurements and tight-tolerance quality checks. How can measurement data be exported for analysis? Readings can be exported via the instrument’s Wireless connection or through the USB port for integration into SPC software or laboratory databases. Is the measuring force adjustable or fixed? The instrument operates with a measuring force in the range of 1.2–2.2 N, designed to provide consistent contact and repeatable readings across standard inspection tasks. Which applications suit this digital indicator best? This electronic indicator is ideal for component inspection, incoming goods control and bench-level process checks where compact range and high accuracy are required. Does the product have an identifiable model or article number for ordering? Yes — the model is listed under article number 120139508M and is offered by Microtech Metrology. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
50mm Digital Dial Gauge 0.001mm Resolution Absolute System Rotating Display 330° IP54 - Metav IndustryLine
Benefit from 0.001 mm resolution, an absolute measuring system and a rotatable display for dependable shop‑floor readings; order the digital indicator directly via Metav Werkzeuge or consult the specialists for application advice. Digital dial indicator M301.039 — 0–50 mm, 0.001 mm resolution, rotatable display (Metav IndustryLine) The Digital dial indicator M301.039 is a compact electronic measuring gauge designed for precise displacement and run‑out checks in workshop, inspection and production environments. High resolution 0.001 mm readout Rotatable display up to 330° for flexible viewing IP54 splash and dust protection Absolute measuring system with 3 V supply Precision that maintains process reliability The electronic gauge delivers a 0–50 mm measuring range with a fine 0.001 mm display step, making it suitable for fine dimensional checks and quality assurance tasks. The combination of a low measurement force (>2.2 N) and a repeatability of ±0.005 mm reduces operator‑induced variation, while the stated accuracy of 0.008 mm provides a clear performance expectation for toleranced work. The absolute measuring system preserves the reference position after power cycles, which simplifies set‑up and reduces cycle time in serial inspection. Designed for robust workshop use and ergonomic operation A display that rotates through 0–330° improves readability in confined fixturing and allows the instrument to be mounted in a variety of orientations without losing sight of the reading. The unit meets IP54 protection, offering reliable resistance to splashes and tool‑shop dust. A glass scale rail ensures stable scanning and consistent signal pickup, while the overall weight of 0.29 kg keeps handling comfortable for frequent checks. Delivery in a protective case supports safe transport and storage between job sites and inspection benches. Digital functions for efficient data handling and flexible measurement The indicator includes a comprehensive set of front‑panel controls (ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/inch and +/- keys) for rapid switching between measurement modes and units. Data output is provided via the RB 6 interface, permitting straightforward connection to data collectors and SPC systems where required. These features make the gauge a practical choice for bench inspection, small‑batch production control and integration into digitised quality workflows without excessive operator training. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine digital indicator M301.039 can be integrated into measurement routines and to arrange delivery in its protective case Technical data Article number: M301.039 GTIN: 4054469164878 ECLASS: 21170308 ETIM: EC003591 Label: Digital dial indicator, 50 x 0.001 mm, Absolute system, rotatable display, IP54 Facts Measuring range: 0–50 mm Resolution / reading: 0.001 mm Accuracy: 0.008 mm Repeatability: 0.005 mm Weight: 0.29 kg Protection rating: IP54 Measuring force: >2.2 N Power / measuring system: Absolute with 3 V Special features Rotatable display 0–330° Glass scale rail for improved scanning Data output: RB 6 Digital functions: ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/inch, +/- keys Delivered in protective case FAQ How accurate is the instrument for routine inspection tasks? The M301.039 digital dial indicator provides an accuracy of 0.008 mm with a repeatability of 0.005 mm, which suits common workshop and quality‑control applications where sub‑hundred‑micrometre consistency is required. Can the display be read when the gauge is mounted in different orientations? Yes, the display rotates through 0–330°, allowing the indicator to be read comfortably from most mounting positions without re‑orienting the whole assembly. Is the unit suitable for use at the machine bench or only in clean inspection rooms? With an IP54 rating and a protected glass scale rail, the instrument is designed for typical machine‑shop environments and bench‑top inspection where splash and dust resistance are beneficial. Does the indicator provide a data output for SPC systems? The gauge offers a data output via the RB 6 interface for connection to data loggers and SPC equipment, facilitating digital recording and process monitoring. What digital functions are available on the display? The display provides ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/inch switching and +/- keys, enabling flexible measurement modes and quick unit changes during inspection routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
50mm Digital Indicator Absolute Display 0–330° Rotatable, IP54 - Metav IndustryLine
Take advantage of a compact, workshop-ready solution that combines high repeatability, absolute measuring technology and a rotatable display for efficient set-ups; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Metav IndustryLine Digital Indicator M301.033 — 50 mm range, 0.01 mm resolution, 330° rotatable display A compact digital indicator designed for precise workshop and inspection tasks, offering an absolute measuring system, fine resolution and a display that can be rotated by up to 330° for ergonomic reading. 50 mm measuring range, resolution 0.01 mm Rotatable display up to 330° Absolute measuring system with 3 V power IP54 splash and dust protection Reliable measurements that save time on the shop floor This instrument is built to deliver consistent, repeatable readings in everyday industrial use. With a resolution of 0.01 mm and a measured repeatability of 0.008 mm, the gauge reduces rework caused by measurement variability and accelerates quality checks. The Absolute measuring system preserves the reference position even after power cycles, which eliminates time-consuming re-zeroing and supports faster set-up in production runs. The compact form factor and robust construction make it suitable for routine dimensional inspection in metalworking and assembly environments. Designed for ergonomic handling and tight spaces A 330° rotatable display allows the readout to be orientated for the operator, reducing the need to reposition workpieces or the indicator itself. The device’s lightweight build and the provided 8 h6 mounting interface simplify attachment to stands or holders, while the measuring force above 2.2 N ensures reliable contact without excessive pressure. The combination of a glass-guided scale and stable electronics gives improved scanning accuracy, especially when taking repeated measurements in limited access areas. Clear digital functions and data connectivity for process control The digital readout offers a comprehensive control set — ON/OFF, origin, 0/ABS, preset, tolerance, mm/inch and +/- keys — supporting flexible measurement workflows and quick toggling between modes. Data output is provided via an RB 6 interface, enabling straightforward connection to downstream logging equipment or a readout unit for traceable documentation of measurement results. For traceability and quality records, the indicator’s absolute system ensures consistent reference behaviour that integrates well into inspection routines and production control. Built to withstand industrial environments With an IP54 rating, the instrument resists dust ingress and splashing liquids typical of workshop conditions, helping to maintain measurement integrity over time. The specified accuracy of 0.015 mm positions this gauge for demanding dimensional control tasks where precise tolerances are required but where a compact, portable instrument is preferred over bench-mounted metrology. The device’s construction emphasises robustness and low maintenance, supporting frequent use across inspection benches and set-up stations. Discuss application requirements or request a tailored quotation from Metav Werkzeuge – contact details below for prompt technical guidance and local supply from Emmerich. Technical Data Article number: M301.033 GTIN: 4054469158372 Category: Messuhren Manufacturer: Metav IndustryLine Core specifications Measuring range: 0–50 mm Resolution: 0.01 mm Accuracy: 0.015 mm Repeatability: 0.008 mm Weight: 0.29 kg Measuring force: >2.2 N Display rotation: 0–330° Protection rating: IP54 Features & materials Measuring system: Absolute with 3 V Data output: RB 6 Digital functions: ON/OFF, ORIGIN, 0/ABS, PRESET, TOL, mm/Inch, +/- Scale guidance: glass slide for improved scanning Mounting: 8 h6 FAQ What precision can be expected in repeated measurements? Repeatability is specified at 0.008 mm; the Metav IndustryLine digital indicator M301.033 provides consistent results for serial inspection tasks thanks to its stable mechanical guidance and electronic processing. Is the display orientation adjustable for awkward set-ups? Yes, the display rotates by up to 330°, allowing the readout to be positioned ergonomically without moving the workpiece or the measuring stand. Can the instrument be integrated into data-collection systems? The unit offers an RB 6 data output interface for connection to readout or logging systems, enabling straightforward transfer of measured values from the Metav IndustryLine gauge. Is the indicator suitable for a workshop environment with occasional splashes and dust? With an IP54 protection rating, the indicator tolerates typical workshop dust and splashes, making it suitable for routine shop-floor measurement tasks. Which mounting standard is used for attaching the indicator? The device uses an 8 h6 mounting interface, compatible with common indicator holders and stands for stable fixturing during inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6-12mm Three-Point Internal Micrometer Self-Centering Set, Supplied in Case - Metav IndustryLine
Take advantage of self‑centring three‑point measurement, hardened measuring faces and a compact 6–12 mm range to inspect blind bores with repeatable accuracy; the set format provides practical coverage across small diameters. Order the Three‑point internal micrometer set MS908.671 directly via Metav Werkzeuge or ask our consultants if needed. Three‑point internal micrometer MS908.671 — self‑centring, hardened faces by Metav IndustryLine The Three‑point internal micrometer MS908.671 is an analogue, precision measuring set for blind‑hole inspection in the micro class, designed to deliver stable readings in confined diameters. Self‑centring three‑point measuring system Measuring range 6–12 mm in micro class Hardened measuring faces for durability Includes adjustment rings 6, 8, 10 mm Precision for small bores and repeatable inspection results This set is classified in the micro class with a 6–12 mm measuring span, making it suitable where short measuring jaws and torsion‑resistant geometry matter. The compact dimensions reduce lever effect and deformation during measurement, which benefits quality control in precision engineering and small‑parts production. As an analogue instrument, it provides a tactile feel during adjustment and a reliable mechanical reference that is simple to verify against calibration standards. Stable centring and wear‑resistant contact surfaces The self‑centring three‑point system ensures the contact points centre automatically in blind bores, reducing centring errors and shortening setup time. Combined with hardened measuring faces, this mechanism keeps contact geometry consistent over many cycles and supports repeatable results when inspecting internal diameters. Included adjustment rings (6, 8, 10 mm) and a 100 mm extension option expand the practical use for varying bore depths and minor diameter steps without compromising alignment. Practical workshop benefits and typical applications Offered as a set of three, the instrument collection covers successive diameter bands within the stated range, which streamlines inspection in toolrooms, fixture production and component assembly lines. The analogue micrometer screw provides fine mechanical control for small adjustments, while the robust design minimises maintenance needs. This combination of features helps to reduce rework, improve first‑pass yield and integrate smoothly into established inspection routines in small‑part manufacture. Contact Metav Werkzeuge to discuss the Metav IndustryLine three‑point internal micrometer set MS908.671 for blind bores and arrange supply or technical advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.671 Manufacturer: Metav IndustryLine Product type: Three‑point internal micrometer set Reading type: Analog Measuring range: 6.0–12.0 mm Pieces per set: 3 Extensions: 100 mm Adjustment rings: 6 mm, 8 mm, 10 mm Hardened measuring faces: yes Self‑centring: yes Facts Measuring range min: 6 mm Measuring range max: 12 mm Reading increment: 0.005 mm Set quantity: 3 pieces Extension length: 100 mm Special features Self‑centring three‑point system Hardened contact faces for long life Analogue micrometer screw drive Suited for blind‑hole/internal bore measurement Compact micro‑class design for small diameters FAQ What measuring range is covered by the set? The set covers a 6–12 mm measuring span suited to micro‑class internal measurements. Is the instrument suitable for blind‑hole inspection? Yes, the Three‑point internal micrometer MS908.671 is specifically designed for blind‑hole (sack‑hole) measurements using a self‑centring three‑point contact system. Are extensions and adjustment rings included? Adjustment rings of 6, 8 and 10 mm are included and a 100 mm extension option is listed for deeper bore measurements. Are the measuring faces hardened? The measuring faces are hardened to resist wear and preserve contact geometry during repeated use. How many instruments are supplied in the set? The delivery comprises a set of three instruments to cover the stated diameter range efficiently. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
62-75mm Three-Point Internal Micrometer Self-Centring, 0.005mm Graduation, Supplied in Case - Metav IndustryLine
Benefit from the self-centring design, carbide measuring faces and ±0.005 mm accuracy to secure reproducible internal measurements in compact assemblies; order the three-point internal micrometer directly via Metav Werkzeuge or consult our specialists for technical guidance. Three-point internal micrometer MS908.660 — self-centring, 62–75 mm range A compact, analogue three-point internal micrometer designed for precise internal diameter checks in confined bores and fine-mechanical work. Self-centring three-point mechanism Measuring range 62–75 mm High accuracy ±0.005 mm Carbide measuring faces, analogue Precision where access is restricted The three-point internal micrometer is engineered for accurate measurements in confined spaces. Its self-centring mechanism ensures the measuring anvils align centrally within a bore, reducing operator-induced eccentricity and improving repeatability. With a readout resolution of 0.005 mm and a verified accuracy of ±0.005 mm, the instrument provides a reliable basis for quality control tasks where small deviations matter. The compact profile and 114 mm body length make this instrument particularly suitable for short, deep bores and components that cannot be accessed with larger gauges, offering precision without the need for complex fixturing. Durable construction for consistent results Built with carbide measuring faces, the instrument resists wear and maintains a stable contact geometry over extended use, which preserves measurement integrity in production environments. The analogue mechanism is robust and free of electronics, making it uncomplicated to operate in workshop conditions where durability is paramount. The combination of hardened contact surfaces and mechanical simplicity translates into low maintenance and consistent performance during repetitive checking routines, supporting efficient inspection workflows on the shop floor. Practical handling and typical applications Designed for ease of use in inspection and assembly, the instrument delivers fast, reliable readings for internal diameters between 62 and 75 mm. Its three-point contact is particularly effective for detecting form deviations and average bore sizes without additional adapters. Typical applications include component verification in machining, maintenance checks on housings and bearings, and quality assurance in small-batch production. The analogue format permits immediate interpretation of results, while the instrument’s geometry supports measurements that would be difficult with external gauges or callipers. Contact Metav Werkzeuge today for tailored advice and to arrange supply of the Metav IndustryLine three-point internal micrometer MS908.660 via Metav Werkzeuge GmbH; technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.660 Brand: Metav IndustryLine Type: Analogue three-point internal micrometer Measuring range: 62–75 mm Readout: 0.005 mm Accuracy: ±0.005 mm Body length: 114 mm Self-centring mechanism Carbide measuring faces Suitable for blind-hole measurement Analogue (mechanical) operation FAQ How accurate is the three-point internal micrometer for routine inspection? The MS908.660 delivers an accuracy of ±0.005 mm, making it suitable for routine precision checks and quality control where sub-hundredth-millimetre repeatability is required. Can the instrument be used in blind or recess bores? Yes, the design is intended for confined and blind-hole measurements; the three-point contact provides reliable central alignment inside such bores. What maintenance is required to preserve measurement accuracy? Regular cleaning of contact surfaces and occasional verification on a calibrated reference ring are recommended to maintain the micrometer’s performance; the carbide measuring faces reduce wear and extend intervals between checks. Is the readout mechanical or electronic? This is an analogue instrument with a mechanical readout at 0.005 mm resolution, favouring robustness in workshop settings without relying on electronics. Which environments and applications suit this instrument best? The three-point internal micrometer is ideal for machine shops, maintenance workshops and inspection benches where compact, repeatable internal measurements are needed across small to medium-sized components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6–8mm Three-Point Internal Micrometer Self-Centring For Blind Holes In Plastic Case - Metav IndustryLine
Compact, self‑centring three‑point internal micrometre with a 6.0–8.0 mm measuring range and high mechanical resolution; the MS908.650 combines precise blind‑hole measurement with hardened measuring faces and a fine 0.001 mm reading—Order the three‑point internal micrometre directly via Metav Werkzeuge or ask our consultants if needed Three‑point internal micrometre MS908.650 — self‑centring, 6.0–8.0 mm range Three‑point internal micrometre MS908.650 delivers reliable blind‑hole measurement for precision workshops and production lines Self‑centring three‑point contact Measuring range 6.0–8.0 mm Resolution 0.001 mm reading Hardened measuring faces (HM) Precision where blind‑hole bores matter The self‑centring three‑point contact mechanism ensures coaxial alignment inside blind holes, reducing measurement variability compared with two‑point probes. With a measuring range of 6.0–8.0 mm and an analogue vernier controlled fine adjustment, this instrument is optimised for small‑diameter bores where repeatability is critical. The device’s geometry minimises radial play so that each measurement reflects the actual bore diameter rather than positioning error, which is particularly valuable in small‑component assembly and quality control workflows. Exceptional reading and repeatability for workshop standards Equipped with a mechanical reading division of 0.001 mm, the instrument offers a fine visual resolution while the stated accuracy of ±0.004 mm provides a clear performance expectation for routine inspections. The analogue vernier design gives tactile feedback during measurement, enabling experienced operators to control contact force intuitively. This combination of high resolution and guaranteed accuracy supports process control in machining and metrology tasks where small deviations can affect assembly fit or functional tolerances. Durable contact faces for industrial use The micrometre is fitted with hardened measuring faces (HM) to withstand repeated contact with workpiece surfaces and abrasive contaminants found in production environments. These robust faces preserve the geometry of the contact points over long service intervals, which reduces drift and the need for frequent re‑profiling. In practice, hardened faces extend usable life and maintain measurement integrity when inspecting ferrous and non‑ferrous components during serial production. Designed for blind‑hole measurement and simple handling Specifically configured for blind‑hole bores, the three‑point contact and compact body (length 54.5 mm) permit access to confined features that larger gauges cannot reach. The instrument includes an adjustment ring (setting ring 6) that allows controlled extension of the contact arms, making it suitable for varied hole depths within the stated range. Its compact, mechanically driven construction requires no batteries and integrates easily into inspection benches, making it a practical choice for laboratories and on‑shop measuring stations where robustness and low maintenance are priorities. Contact Metav Werkzeuge today to discuss how the MS908.650 can be integrated into existing inspection routines or to request tailored advice from our technical consultants Technical data Article number: MS908.650 Manufacturer: Metav IndustryLine Type: Three‑point internal micrometre Facts Measuring range: 6.0–8.0 mm Length: 54.5 mm Reading increment: 0.001 mm Accuracy: ±0.004 mm Adjustment ring: 6 Special features Self‑centring three‑point contact Hardened measuring faces (HM) Analogue vernier reading Suitable for blind‑hole bores Category: Messschrauben FAQ What measurement range does this instrument cover? The MS908.650 covers a measuring range of 6.0–8.0 mm, optimised for small blind‑hole bores. Is the device suitable for repetitive production checks? Yes, the MS908.650 is designed for workshop and production use with hardened measuring faces and a robust three‑point contact that supports repeatable inspections. What level of accuracy and resolution can be expected? The instrument provides a reading increment of 0.001 mm and a stated accuracy of ±0.004 mm, suitable for demanding quality control tasks. Can the micrometre measure deep blind holes? The compact length (54.5 mm) and the adjustment ring (6) make the MS908.650 appropriate for many blind‑hole depths within its 6.0–8.0 mm range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75-100mm Precision Micrometer With Colour Touchscreen, Wireless USB, IP65 - Microtech Metrology
Benefit from high-precision measurement, robust ingress protection and seamless data transfer for efficient quality control. Combine the accuracy 0.004 mm, Wireless + USB output and IP65 sealing for reliable on‑site and lab use. Order directly via Metav Werkzeuge or consult our specialists for integration advice. Microtech Micrometer — digital micrometer, 75–100 mm, IP65, 2.4" touchscreen The Microtech Micrometer is a digitally measured micrometer designed for precise workshop and laboratory measurements across a 75–100 mm range. High precision ±0.004 mm accuracy Integrated Wireless + USB output Robust IP65 protection Colour 2.4" touchscreen display Precision where repeatability counts The instrument delivers substantial measurement reliability thanks to its accuracy 0.004 mm and high-resolution reading of 0.0001 mm, which together reduce uncertainty in routine inspection tasks. This level of precision supports repeatable results when checking components with tight tolerances and enables confident go/no-go decisions in production. The solid measuring faces (Ø12 mm) maintain consistent contact geometry for each reading, limiting variability introduced by changing contact conditions. Seamless data capture for process control Equipped with Wireless + USB outputs and a clear 2.4" touchscreen, the device simplifies data logging and process documentation. Measurements can be transmitted directly to inspection software or a laptop for traceable records, reducing transcription errors and speeding up reporting. Integration into existing quality workflows is straightforward, making the instrument suitable for traceable inspection routines and batch control where documented evidence is required. Built for workshop durability and continuous use The unit’s IP65 rating protects the electronics against dust and water jets, which extends operational life in harsher workshop environments. The robust construction means fewer interruptions for maintenance and reliable performance on the shop floor. The digital electronics and sealed enclosure also contribute to lower service frequency compared with purely analogue instruments, promoting sustained availability for production-critical measurement tasks. Practical handling and measurement versatility Operating ergonomics are tuned for regular use: the digital display is legible and responsive, and the compact form factor supports comfortable one‑hand measurement across the measurement range 75–100 mm. The instrument’s measuring faces of Ø12 mm give a stable contact area for consistent pressure distribution. As a digitally driven micrometer, it reduces operator influence on readout interpretation and helps maintain throughput during repetitive inspection cycles. For detailed technical advice on the Microtech Micrometer or to discuss integration into an existing inspection line, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our consultants provide specification guidance and delivery options tailored to professional requirements. Technical data Article number: 133801008 GTIN: 4061905457982 Manufacturer: Microtech Metrology Facts Measurement range: 75–100 mm Accuracy: 0.004 mm Reading: 0.0001 mm Display: Colour 2.4" touchscreen Protection class: IP65 Special features Data output: Wireless + USB Measuring faces: Ø12 mm Instrument type: Digital micrometer Digital: yes FAQ What measurement range does this micrometer cover? The micrometer covers a 75–100 mm range, suitable for medium‑sized component checks and workshop inspection tasks. How accurate is the instrument for inspection work? With an accuracy of 0.004 mm and a reading step of 0.0001 mm, the instrument meets the demands of precision quality control in production and lab environments. Can measurement data be exported directly to inspection software? Yes, the device offers Wireless + USB outputs for direct data transfer to PCs or data loggers, facilitating digital record keeping. Is the micrometer suitable for harsh workshop conditions? The IP65 rating provides dust and water‑jet protection, making the instrument durable for routine shop‑floor use. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
75-88mm Three-Point Internal Micrometer Self-Centring, Hardened Measuring Faces, Supplied in Case - Metav IndustryLine
Benefit from precise three-point contact, a self-centring mechanism and an accuracy of 0.005 mm for reliable blind‑hole measurement; order the MS908.661 directly via Metav Werkzeuge or ask our consultants for application advice. Three‑point internal micrometer MS908.661 — 75–88 mm range, self‑centring (Metav IndustryLine) The Three‑point internal micrometer MS908.661 offers a compact, mechanically robust solution for accurate measurement of blind bores between 75 and 88 mm, combining repeatable contact geometry with workshop‑grade durability. Self‑centring three‑point contact Measuring range 75–88 mm Accuracy 0.005 mm Precise three‑point geometry for repeatable blind‑hole results The instrument employs a three‑point contact arrangement that engages the bore at equidistant positions, producing consistent centring and minimising eccentricity in blind‑hole measurements. With a specified accuracy of 0.005 mm and a reading increment of 0.005 mm, the mechanical design prioritises repeatability and straightforward interpretation of results. This focus on measurable performance supports quicker decision‑making on the shop floor and reduces the likelihood of rework caused by inconsistent bore centring. Robust construction and easy handling for daily use Built for persistent use in production and inspection areas, the gauge features hardened measuring faces and an analogue measuring mechanism that requires no batteries. The compact body (length 114 mm) and an adjustable setting ring (87) provide tactile control during measurement operations. Hardened contact surfaces extend service life under typical workshop conditions, while the analogue format keeps the instrument immediately usable without electronic maintenance. The combined effect is low‑maintenance operation with dependable mechanical accuracy. Practical suitability and workflow benefits Designed specifically for blind‑hole applications, the tool is suited to toolrooms, maintenance shops and quality control benches where internal diameters must be checked quickly and reliably. The self‑centring action reduces setup time and helps standardise measurement procedures across operators, improving throughput and traceability. As a purely mechanical gauge it integrates easily with established inspection routines and supports rapid pass/fail decisions without additional calibration steps beyond routine verification. Quality assurance and provenance that support procurement Supplied under the Metav IndustryLine umbrella, the instrument represents a balance of functional precision and workshop pragmatism. Choice of a mechanically driven, three‑point internal gauge is a rational investment when repeatability and simple operation are priorities. Metav’s approach to product selection and distribution provides transparency and supply reliability for industrial buyers who prioritise consistent measurement outcomes. For technical availability and procurement of the MS908.661 three‑point internal micrometer, contact Metav Werkzeuge for product guidance and stock information at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: MS908.661 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Core specifications Measuring range: 75–88 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 114 mm Setting ring: 87 Special features Self‑centring three‑point contact Hardened measuring faces Analogue measuring mechanism Suitable for blind‑hole bores Category: Micrometers FAQ What measuring range does this instrument cover? The MS908.661 covers a measuring range of 75–88 mm and is therefore suited to medium‑sized internal diameters such as blind bores in assemblies. How precise is the measurement? Precision is stated as 0.005 mm with a reading increment of 0.005 mm, which ensures repeatable results for standard workshop inspection tasks. Why is three‑point contact advantageous for blind holes? Three‑point contact centres the gauge automatically within the bore, reducing eccentricity and improving repeatability compared with single‑point internal probes. Where is this instrument typically used? This analogue internal micrometer is used in toolrooms, maintenance workshops and quality control where robust, battery‑free measurement of blind bores is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com