Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
13.41 mm Test Pin, Single, 50 mm Length Workshop Version - Metav IndustryLine
Precision workshop gauge pin with a 13.41 mm diameter, 50 mm length and an accuracy of ±0.002 mm provides repeatable end‑measure checks and robust daily use; supplied in a protective transport case and made from special steel for long service life. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Pin, 13.41 mm Ø, 50 mm Length – Metav IndustryLine The Gauge Pin, 13.41 mm Ø, 50 mm is a workshop‑grade precision pin for end‑measure verification and tight‑tolerance checking of small components Diameter 13.41 mm, accuracy ±0.002 mm 50 mm length, workshop design Supplied in a protective transport case Reliable end‑measure verification for small components The precision pin delivers measurable repeatability thanks to its ±0.002 mm tolerance, enabling reliable verification of bores, fits and end‑dimensions in production and inspection tasks. Such a tight tolerance corresponds to two micrometres of deviation allowance, which supports quality control where small variances affect assembly performance. By using a hardened and ground pin, the tool reduces uncertainty at the point of contact and helps maintain consistent production outcomes. Robust workshop construction for daily handling Manufactured from special steel, the unit is designed for everyday workshop use where resilience and surface integrity matter. The 50 mm shank length offers a practical balance between handling comfort and reach, while the workshop design resists wear under frequent insertion and extraction cycles. Classified for the Micro range (10–100 mm), this pin is particularly suited to fine mechanical tasks such as gauge setting, bore checking and fixture validation where compact, stiff measuring tools are required. Clear handling benefits and application scope The solid construction simplifies handling on the shop floor: one compact tool provides precise reference measurements for jigs, fixtures and incoming inspection. Supplied in a protective transport case, the pin stays protected during storage and transit, reducing the risk of damage that would alter its dimensional performance. As a gauge pin in the Messstifte category, it integrates readily into measurement routines that demand consistent contact geometry and minimal deformation under light manual force. Contact Metav Werkzeuge for tailored application advice and secure supply of the Metav IndustryLine 13.41 mm gauge pin; Metav Werkzeuge can advise on suitability for specific inspection tasks and arrange fast delivery from Emmerich. Technical Data SKU: M323.D41 GTIN: 4061905068980 Material: Special steel Weight: 0.1 kg Accuracy: ±0.002 mm Length: 50 mm Diameter: 13.41 mm Feature: Workshop version Delivery: Protective transport case Numbers / Core technical data Length: 50 mm Diameter: 13.41 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features / Applications Material: Special steel Workshop design for everyday use Suitable for Micro range measurements (10–100 mm) Protective transport case included Category: Gauge pin (Messstifte) FAQ What tolerance does this gauge pin offer? The gauge pin is specified with an accuracy of ±0.002 mm, providing micrometre‑level repeatability suitable for precision end‑measure checks. Is the gauge pin suitable for bore inspection on small parts? Yes. The 13.41 mm diameter and the 50 mm length make this gauge pin well suited to bore checking, fit verification and fixture validation in small component inspection. What material is used for the pin and how does it affect durability? The pin is made from special steel; this material ensures surface hardness and wear resistance, supporting long service life under frequent use. Does the product include protective packaging? The pin is supplied in a protective transport case to reduce the risk of damage during storage and transit and to help preserve dimensional accuracy. Which product identifiers should be quoted when ordering? Please quote the SKU M323.D41 and the GTIN 4061905068980 to ensure the correct gauge pin from the Metav IndustryLine is supplied. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.42mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Benefit from workshop-grade durability, a compact 50 mm length and a fine accuracy of ±0.002 mm for reliable end-dimension checks. Take advantage of the special steel construction and precise 13.42 mm diameter to maintain consistent production quality. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.D42 — single test pin, Ø 13.42 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.D42 is a single precision test pin intended for end-dimension verification and alignment tasks in workshop and jig-making applications. Workshop version for robust use Diameter 13.42 mm Length 50 mm Accuracy ±0.002 mm Special steel construction Precise measurement where it matters The M323.D42 is engineered for repeatable end-dimension control, delivering a declared positional accuracy of ±0.002 mm. This level of precision places the pin firmly in the realm of fine workshop metrology, where small deviations can affect assembly fit or running clearance. Because the diameter is specified as 13.42 mm, it functions as a reliable reference in bore gauges, alignment jigs and verification fixtures. The clear numeric specification reduces ambiguity during quality checks and supports traceable inspection routines. Compact format for fine mechanical work With a 50 mm length and a diameter in the micro range, the pin belongs to the micro measurement category (10–100 mm). That classification means the tool is particularly suited to tasks that require high stiffness in a compact form: small bores, precision fixtures and components for subassemblies. The short overall length helps to keep bending and measurement uncertainty low, so measurements remain reproducible without complex support arrangements. Durability and workshop readiness Constructed from special steel, the pin has been designed for routine workshop use and frequent handling. The workshop version emphasises robustness while still preserving the dimensional stability required for reference checks. Supplied as a single test pin, it is easy to integrate into existing gauge sets or to use as a dedicated master for pass/fail tests. The material choice supports wear resistance, which helps maintain the nominal diameter over many inspection cycles. Practical benefits for production and quality control Using a dedicated test pin simplifies setup and shortens inspection time by providing a direct mechanical reference for go/no-go checks and alignment operations. The compact form factor and clear specification minimise setup errors and ease communication between production and quality teams. When paired with documented inspection procedures, the pin contributes to a predictable measurement process and fewer ambiguous results during incoming or in‑process checks. For procurement advice or stock information on the Metav IndustryLine gauge pin M323.D42, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 to discuss availability and suitability for specific applications Technical data Article number: M323.D42 GTIN: 4061905069734 Brand: Metav IndustryLine Facts Diameter: 13.42 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Single piece supply Category: gauge pins / test pins Application: end-dimension checks FAQ What tolerance can be expected from this pin? The gauge pin M323.D42 is specified with an accuracy of ±0.002 mm, providing a fine tolerance suitable for precision workshop checks. What is the pin made of? The pin is manufactured from special steel, chosen for its wear resistance and dimensional stability in routine workshop use. Is the product supplied individually or as part of a set? This item is supplied as a single test pin (single piece), making it straightforward to use as a dedicated reference or to add to an existing set. Which measurement category does this pin fall into? With a diameter of 13.42 mm and a 50 mm length, the pin fits the micro measurement category (10–100 mm), ideal for fine mechanical and small‑part applications. How can the product be identified in orders or inventory? Identification is possible via the article number M323.D42 and GTIN 4061905069734 for unambiguous ordering and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.43mm Gauge Pin Length 50mm, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of tight dimensional control, robust workshop design and simple traceability for consistent end-measure checks; order the inspection pin directly via Metav Werkzeuge or contact our consultants for application support. Inspection pin M323.D43 — 13.43 mm diameter, 50 mm length (Metav IndustryLine) A Metav IndustryLine inspection pin for routine end‑measurement and gauge checks in workshop and inspection environments Workshop-grade inspection design Diameter 13.43 mm for accurate fits Tolerance ±0.002 mm for precision checks Precision where it counts for assembly and inspection The Metav IndustryLine inspection pin (M323.D43) is manufactured for applications that demand reproducible end‑measurement results. With a nominal diameter of 13.43 mm and a geometric tolerance of ±0.002 mm, the pin is intended for use as an end gauge or reference mandrel in assembly, inspection and go/no‑go testing. The controlled tolerance reduces measurement uncertainty during pass/fail checks and simplifies matching to mating bores or locating features. Built to withstand workshop routines while remaining easy to handle This single inspection pin combines a compact 50 mm length with a lightweight mass, making it straightforward to position in fixtures or measuring jigs. The workshop execution ensures surface and finish tolerances that tolerate frequent handling and insertion cycles without compromising fit. The compact geometry also supports use in confined setups where long probes would impede access, so operators benefit from quick, repeatable positioning during batch checks. Material selection and functional reliability explained Produced from special steel, the gauge pin offers a balance between surface hardness and dimensional stability, supporting repeated use in metalworking environments. The material choice minimises wear on contact surfaces while maintaining the required roundness and cylindricity for accurate fits. For traceability and inventory control, the item is supplied with its SKU and GTIN, enabling straightforward integration into quality documentation and inspection records. Practical integration into measuring workflows As a simple, robust reference element, the inspection pin suits a range of metrology tasks: end‑dimension verification, alignment of mating parts and use as a physical limit gauge in manual or semi‑automatic checks. The product’s measured form and tight tolerance support efficient decision‑making on the shop floor, reducing rework and supporting consistent assembly outcomes. Compatibility with common fixture designs and standard gauge blocks makes it a pragmatic choice for maintenance and small series production environments. Order the Metav IndustryLine inspection pin M323.D43 from Metav Werkzeuge for dependable workshop accuracy — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored technical advice Technical Data Article number: M323.D43 GTIN: 4061905069741 Manufacturer: Metav IndustryLine Material: Special steel Label: Inspection pin, single, 13.43 mm diameter, 50 mm length Numerical data Diameter: 13.43 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Workshop execution Single inspection pin Application: end measurement Category: Gauge pins / Messstifte FAQ What is the nominal diameter and tolerance of this inspection pin? The inspection pin has a nominal diameter of 13.43 mm and a stated tolerance of ±0.002 mm for precise end‑measurement tasks. Is the M323.D43 suitable for repeated use in a production environment? Yes, the M323.D43 is designed in a workshop execution with special steel to withstand frequent handling and insertion cycles while maintaining dimensional stability. Can this pin be used as an alignment or reference gauge? The inspection pin is suitable as an end gauge or reference mandrel for alignment, mating‑feature checks and simple go/no‑go evaluations in workshop settings. How is the product identified for traceability? The item is supplied with SKU M323.D43 and GTIN 4061905069741 for integration into inspection records and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.44mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Precision and durability in a compact format: the single gauge pin offers a 13.44 mm nominal diameter with a 50 mm overall length and an industrial tolerance of ±0.002 mm, ensuring reliable reference measurements in production and inspection. Benefit from a robust special steel construction and workshop-ready finish — order the single gauge pin M323.D44 directly via Metav Werkzeuge or ask our consultants if needed. Single gauge pin M323.D44 — 13.44 mm Ø, 50 mm length (Metav IndustryLine) Single gauge pin M323.D44 designed for reference measurements and go/no-go checks in workshop and small-series inspection tasks Accurate to ±0.002 mm 13.44 mm nominal diameter 50 mm overall length Delivered in protective transport box High-precision reference for repeatable checks The M323.D44 is built to provide repeatable dimensional references, with a verified tolerance of ±0.002 mm that places it in the high-precision class for gauging pins. Manufactured from special steel, the pin maintains roundness and dimensional stability under typical workshop handling, which reduces setup time for measuring routines and improves throughput during in-process checks. This mechanical reliability supports faster decision-making on the shop floor and fewer measurement-induced reworks. Compact design that suits micro-range inspection Classified within the micro range (measurement spans between 10 mm and 100 mm), the pin’s 13.44 mm diameter and 50 mm length combine reach with low bending sensitivity, making it suitable for fine mechanical tasks and small components. The compact dimensions ensure easy handling during fixture setup and manual gauging, while the workshop-oriented finish aids grip and alignment. The result is a practical inspection aid that simplifies handling without compromising metrological performance. Workshop-ready delivery and practical traceability Supplied as a workshop version and packaged in a protective transport box, this gauge pin is ready for immediate use at the bench or in assembly jigs. The robust packaging reduces risk during storage and transport and supports organised inventory management on the shop floor. As a Metav IndustryLine item, the pin benefits from accessible supply and the company’s quality filter in Emmerich, which helps ensure consistent availability and traceable sourcing for production-critical tools. Contact Metav Werkzeuge today to obtain the Metav IndustryLine single gauge pin M323.D44, check compatibility with specific measuring fixtures or request tailored advice from our consultants at the Emmerich team Technical data SKU: M323.D44 GTIN: 4061905069758 Category: Messstifte Facts Diameter: 13.44 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Delivered in a protective transport box Accuracy suited to fine inspection tasks FAQ What material is the gauge pin made from? The single gauge pin M323.D44 is manufactured from special steel, selected for dimensional stability and workshop durability. Is the tolerance of ±0.002 mm sufficient for precision inspection? Yes, the ±0.002 mm tolerance specified for this gauge pin positions it for precise reference measurements and reliable go/no-go checks in fine mechanical and workshop applications. Does the product come with a calibration certificate? This item is not indicated as supplied calibrated; a calibration certificate is only provided if the product is explicitly labelled as calibrated. For which applications is this gauge pin most suitable? The M323.D44 is best used for small-part inspection, fixture set-up and reference checks within the micro measurement range where compact dimensions and high repeatability are required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.45mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Combine ±0.002 mm tolerance with a compact 13.45 mm diameter and a 50 mm working length to secure reproducible fit checks and end-measurements; rely on the workshop-grade construction and specialist steel for long service life. Order the gauge pin directly via Metav Werkzeuge or consult our team for specification advice. M323.D45 gauge pin — 13.45 mm diameter, 50 mm length (Metav IndustryLine) The M323.D45 gauge pin is a workshop-grade checking pin designed for precise fit verification and end‑measurement tasks in production and inspection environments. Diameter 13.45 mm, tolerance ±0.002 50 mm length in workshop version Manufactured from special steel for durability Single item for individual inspection tasks Accurate fit control for assembly and inspection A ground checking pin with a declared tolerance of ±0.002 mm provides a reliable reference when verifying bore sizes and mating parts. The tight tolerance reduces uncertainty in go/no‑go decisions and shortens inspection cycles, which improves throughput in quality control. By converting dimensional data into clear pass/fail outcomes, the pin removes ambiguity from routine checks and supports traceable acceptance criteria for small series and batch production alike. Robust construction that endures workshop routines Manufactured in special steel and offered in a workshop configuration, this checking pin resists wear from repeated insertion and contact with common mating materials. The 50 mm length offers sufficient engagement for many fits while remaining compact for handheld use or bench fixtures; the modest mass also aids steady handling during manual inspections. This combination of material and design reduces the frequency of replacements and maintains measurement integrity over many cycles. Simple integration into quality workflows Marked and stocked under the SKU M323.D45 with an assigned GTIN for traceability, the pin is suited for standardised inspection procedures and documentation. Using a single, calibrated reference piece accelerates setup of comparative checks on production lines and simplifies tool lists for incoming inspection. The result is fewer process interruptions, faster decision-making at the inspection station and a more consistent record of conformity across repeating production steps. Contact Metav Werkzeuge for application advice or to arrange supply of the M323.D45 gauge pin and ensure the right fit verification tools for production needs Technical data SKU: M323.D45 GTIN: 4061905066016 Category: Gauge pins / Messstifte Manufacturer: Metav IndustryLine Facts Diameter: 13.45 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: Special steel Sold individually Suitable for end‑measurements and fit checks FAQ What tolerance does the gauge pin offer? The M323.D45 gauge pin is specified with a tolerance of ±0.002 mm, providing a high degree of repeatability for fit and end‑measurement applications. Which materials is the pin suitable for testing against? The checking pin, manufactured from special steel, is suitable as a reference for mating parts made of common engineering materials where a hard, wear‑resistant probe is required. Is the pin supplied as a single item or in sets? This article is supplied as a single item; the product is listed and stocked under SKU M323.D45 for individual inspection tasks. How does the pin support production inspection workflows? With a defined diameter and traceable identification (GTIN and SKU), the pin simplifies standard operating procedures and documentation for repetitive quality checks. Can the pin be used for assembly verification on small components? Yes, the compact diameter and 50 mm length make this gauge pin well suited to assembly and fit verification of small to medium components where controlled insertion depth is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.46mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise diameter control and minimal runout in a compact inspection element; the 13.46 mm diameter combined with a ±0.002 mm tolerance and 50 mm overall length supports repeatable end‑dimension checks in production and inspection routines. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for application-specific guidance. Gauge pin M323.D46 — 13.46 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin for precise end‑dimension verification and go/no‑go testing in workshop and inspection fixtures. Precision diameter 13.46 mm, tolerance ±0.002 mm 50 mm overall length for end‑face checks Made from special steel for wear resistance Reliable dimensional control for process stability The compact gauge pin delivers consistent dimensional references that reduce measurement uncertainty during frequent checks. With a nominal diameter of 13.46 mm and an indicated ±0.002 mm runout tolerance, the element provides the level of precision required for small‑part inspection and fixture alignment. The controlled tolerance helps to identify process drift early, improving first‑pass yield and reducing rework costs. Durable construction that keeps inspection intervals predictable Manufactured from special steel, the pin resists surface wear and preserves the reference diameter over repeated use. The material selection offers improved wear resistance compared with standard steels, which supports longer service life in high‑cycle inspection settings. The compact 50 mm length balances handling convenience with sufficient contact area for reliable end‑dimension verification. Simple integration into gauges and inspection jigs The gauge pin is suitable for insertion into fixture bores, stack gauges or as a reference plug in bench checks; its compact design enables quick interchangeability and minimal set‑up time. Marked with the internal SKU and traceable GTIN, the item simplifies inventory control and ensures reproducible identification across workstations. The low mass and straightforward geometry aid fast positioning while maintaining repeatability. Measurable benefits for workshop and production teams Using a tightly specified pin reduces subjective assessment in go/no‑go routines and supports objective acceptance criteria in quality documentation. The element's nominal dimensions and tolerance are suitable for precision fit checks, enabling faster decision cycles at incoming inspection and during in‑process verification. The robust finish reduces polishing and dressing frequency, lowering maintenance effort. Choose the Metav IndustryLine gauge pin M323.D46 for dependable, repeatable end‑dimension checks and contact Metav Werkzeuge for tailored advice on integrating this element into existing inspection fixtures Technical data Article number: M323.D46 GTIN: 4061905066023 Manufacturer: Metav IndustryLine Facts Nominal diameter: 13.46 mm Length: 50 mm Tolerance / runout: ±0.002 mm Weight: 0.1 kg Material: special steel Special features Workshop version (Werkstatt‑Ausführung) Single piece delivery Compact geometry for fixture insertion Traceable GTIN and SKU M323.D46 FAQ What inspection tasks is this gauge pin best suited for? It is ideal for end‑dimension verification, go/no‑go checks and fixture alignment where a compact, precision pin with 13.46 mm nominal diameter is required; the Metav IndustryLine gauge pin M323.D46 supports quick, repeatable checks. How accurate is the diameter of the pin? The pin is specified with a runout/tolerance of ±0.002 mm, which enables high repeatability for small‑part inspection and reduces ambiguity in pass/fail assessments. What material is the pin made from and why does it matter? Made from special steel, the gauge pin offers enhanced wear resistance compared with standard grades, extending service life and preserving reference dimensions under frequent use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.47mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the workshop-grade build, tight ±0.002 mm accuracy and compact 13.47 mm diameter for reproducible end‑measure checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin (single) – 13.47 mm, 50 mm length (Metav IndustryLine) The gauge pin 13.47 mm is a workshop-grade inspection pin for precise end‑measure verification and hole gauging in component checks. Workshop-grade design for daily use Diameter 13.47 mm with ±0.002 mm accuracy Length 50 mm for recessed measurements Supplied in transport case Precision that speeds routine inspection This inspection pin delivers a measured outcome thanks to its ±0.002 mm specification, reducing uncertainty during rapid go/no‑go checks and repeat measurements. The compact 13.47 mm diameter is suited to fine hole gauging and end‑measure verification in assembly and machining operations; the close tolerance translates into fewer rechecks and a smoother quality workflow. The result is quantifiable time savings in standard inspection cycles. Robust workshop design for everyday handling Constructed from special steel and offered in a workshop version, the pin resists wear during frequent insertion and offers consistent contact geometry over repeated use. The 50 mm length provides reach into recesses while maintaining a rigid profile that limits bending. Supplied in a protective transport case for safe movement between workstations, the tool is set up for practical shopfloor use without additional packaging effort. Simple integration into existing inspection routines As a single measuring pin, it functions as a reliable reference gauge for production sampling, first‑article checks and occasional verification of hole diameters. The compact format supports handheld gauging as well as fixture‑based checks; its reproducible dimensions make it a practical complement to calipers and bench gauges, enhancing throughput in standard quality control tasks. Clear technical attributes for procurement and traceability The pin’s straightforward specification—13.47 mm diameter, 50 mm overall length and ±0.002 mm dimensional variation—makes it easy to compare with existing standards and procurement lists. The modest mass and compact footprint simplify storage and handling on the shopfloor. For teams focused on reproducible inspection outcomes, this measuring pin provides a low‑complexity, high‑precision option. For Metav IndustryLine precision and workshop suitability, contact Metav Werkzeuge in Emmerich for tailored advice and ordering: info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.D47 GTIN: 4061905066030 Manufacturer: Metav IndustryLine Weight: 0.1 kg Facts Diameter: 13.47 mm Length: 50 mm Accuracy: ±0.002 mm Mass: 0.1 kg Special features Material: Special steel Workshop version Supplied in transport case (plastic or wooden) Category: Gauge pin / Measuring pin FAQ What applications suit this gauge pin best? The gauge pin M323.D47 is ideal for end‑measure verification, hole gauging and routine go/no‑go checks in machining and assembly workflows. Is the dimensional accuracy suitable for standard workshop control? Yes; the ±0.002 mm accuracy of this Metav IndustryLine measuring pin meets tight workshop tolerances for component inspection and sampling. How is the pin supplied and stored? The inspection pin is supplied in a protective transport case (plastic or wooden) to protect the contact geometry during handling and storage. What material is used for the pin and why does that matter? Made from special steel, the pin offers wear resistance and stable contact surfaces, supporting reproducible measurements over time. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.49mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a workshop‑grade construction, 13.49 mm diameter accuracy and a compact 50 mm length for reliable end‑measurement checks; order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.D49 — gauge pin Ø 13.49 mm, 50 mm length (Metav IndustryLine) A Test pin M323.D49 designed for precise end‑measurements and fixture checks in workshop and inspection environments Workshop version, robust design Diameter 13.49 mm, precision ±0.002 Compact 50 mm length for tight fixtures Reproducible checks with industrial accuracy The gauge pin delivers high repeatability thanks to its tight manufacturing tolerance of ±0.002 mm, which supports quantitative go/no‑go and end‑dimension assessments. In practical terms, this level of control converts into fewer reworks and faster setup times on the shop floor: a stable reference dimension reduces variation when aligning fixtures or verifying bore sizes. The design is therefore particularly suitable where measurable, documentable results are required for quality control processes. Robust construction for daily workshop use Built as a workshop version, the pin is made from special steel to withstand handling and routine use. The material choice prioritises wear resistance and dimensional stability under normal operating conditions; this means less frequent replacement and maintained accuracy over many inspection cycles. The compact format and balanced mass ensure the pin is easy to position in jigs and comparators while resisting minor knocks and scratches that commonly occur in production environments. Small footprint, wide applicability With a diameter of 13.49 mm and a length of 50 mm, the pin is optimised for confined spaces and smaller assemblies where bulkier gauges are impractical. Its geometry makes it useful for end‑measurement, checking plug fits, and verifying mating components in assemblies. The single‑piece supply format (individual pin) keeps inventory flexible: it can be incorporated into bespoke sets or used as a stand‑alone reference for targeted inspection tasks. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich (+49 2822 7131930, info@metav-werkzeuge.com) for procurement advice and reliable supply to the workbench Technical data SKU: M323.D49 GTIN: 4061905066054 Manufacturer: Metav IndustryLine Material: Special steel Special feature: Werkstatt‑Ausführung Story trigger: endmasse Facts Diameter: 13.49 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Supplied individually Suitable for end‑measurement and plug checks Compact form factor for tight fixtures FAQ What tolerance can be expected from the M323.D49? The M323.D49 gauge pin is manufactured to a tolerance of ±0.002 mm, offering the precision required for fine measurement tasks in workshop inspection routines. Which material is used for this gauge pin? The pin is produced from special steel, providing a balance of wear resistance and dimensional stability for repeated checking operations. For which applications is this test pin intended? This gauge pin is intended for end‑dimension checks, plug‑fit verification and fixture alignment in workshop and light production settings; its workshop version construction supports everyday use. Is the pin delivered as part of a set or individually? The product is supplied as an individual test pin (SKU M323.D49), allowing integration into custom inspection sets or use as a single reference gauge. How should the pin be handled to maintain accuracy? Handle the pin with care to avoid contamination and impact; store it clean and dry and inspect surfaces before measurement to preserve the ±0.002 mm accuracy. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.4mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high repeatability, compact workshop design and robust material for dependable end‑dimension checks; the precision of ±0.002 mm reduces rework and speeds quality decisions. Order the gauge directly via Metav Werkzeuge or ask the consultants for application advice. Single pin gauge M323.D40 — 13.4 mm diameter, 50 mm length (Metav IndustryLine) The single pin gauge M323.D40 is a compact inspection pin for fast end‑dimension verification in workshop and production environments High repeatability ±0.002 mm Diameter 13.4 mm for tight fits 50 mm hardened length for stable support Workshop version made from special steel Precision that shortens inspection cycles The compact inspection pin is designed for decisive dimensional checks where repeatability and clear tolerances matter. With a stated variation of ±0.002 mm, the gauge pin delivers measurement certainty that supports faster go/no‑go decisions on the shop floor and reduces downstream rework. The controlled diameter of 13.4 mm combined with a 50 mm length provides sufficient engagement depth for most end‑dimension checks while remaining easy to handle. This makes the tool particularly effective in series inspection, jigs and fixture checks where quick validation is required rather than lengthy measurement setups. Built for workshop handling and durability Constructed in special steel and specified as a workshop execution, the pin gauge resists everyday wear and maintains form under routine use. The design prioritises secure seating in fixtures and comfortable handling during repetitive tasks, supporting steady workflows in machining and assembly operations. Weight and balance have been tuned to ensure stable placement during inspection; the solid construction helps maintain dimensional stability over many cycles, giving a consistent reference that teams can rely on for serial checks and final inspections. Integrates with measurement routines and documentation The pin gauge fits into existing inspection processes as a stable reference instrument. Marked with SKU M323.D40 and traceable by GTIN 4061905068973, the part is straightforward to catalogue in quality systems and batch records. Its compact geometry reduces setup time compared with larger gauges, allowing technicians to validate bores and seating faces quickly. When used alongside calibrated gauges and documented control plans, this single pin gauge supports repeatable results and clear audit trails for internal quality control. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to discuss suitability for specific inspection tasks or to request the M323.D40 pin gauge directly. Technical data SKU: M323.D40 GTIN: 4061905068973 Category: Messstifte Facts Diameter: 13.4 mm Length: 50 mm Variation / Repeatability: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Version: workshop execution Application: end‑dimension checks, fixture verification FAQ What tolerance class does this pin gauge provide? The supplied single pin gauge offers a variation of ±0.002 mm, making it suitable for tight workshop inspections where high repeatability is required. Is the material corrosion‑resistant for humid environments? The gauge is manufactured from special steel and specified in a workshop execution; further surface protection options can be checked with Metav Werkzeuge if environmental resistance is required. Can this gauge be used for bore verification and seating checks? Yes, the 13.4 mm diameter and 50 mm engagement length are suitable for many bore verifications and seating face checks in fixtures and jigs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.51mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop‑grade measuring reference that combines 13.51 mm nominal diameter, a 50 mm length and a confirmed ±0.002 mm dimensional tolerance for reliable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Pin gauge, single, 13.51 mm, length 50 mm (M323.D51) — workshop version, special steel The pin gauge, single, 13.51 mm, length 50 mm is a hardened test pin intended for precision end‑measure inspection and gauge setting in workshop and production metrology. Workshop version for rugged use Diameter 13.51 mm with ±0.002 mm accuracy Length 50 mm for reach and stability Reliable dimensional reference for everyday workshop control This workshop‑grade gauge pin provides a stable reference for end‑measure tasks and quick dimensional checks. The declared ±0.002 mm accuracy positions the pin as a high‑precision reference suitable where repeatable, traceable checks are required. Made from special steel, the pin resists routine wear and maintains its profile under typical workshop handling. The compact geometry and 50 mm length deliver a practical balance of reach and rigidity, reducing bending and measurement variation during use. Compact format with industrial precision for small components Classified in the micro measuring range (10–100 mm), this pin is optimised for fine mechanical parts and assembly jigs where space is limited but tolerance demands are high. The nominal 13.51 mm diameter gives a definitive mating size for end‑measure and plug checks, while the workshop specification ensures compatibility with bench fixtures, gauge blocks and sizing inserts. The simple, single‑pin format is convenient for sorting, go/no‑go checks and rapid process verification without the overhead of complex fixturing. Durable design and practical delivery for immediate deployment Built as a workshop execution item, the pin combines a hardened surface finish with a geometry that supports repeatable touch and feel measurements over many cycles. Delivery includes a protective case to safeguard the pin in transit and storage, ensuring the measuring face stays free of damage prior to use. Lightweight at approximately 0.1 kg, the pin is easy to handle and integrates smoothly into inspection kits and portable measuring sets, making it a reliable tool for production lines and maintenance benches. Choose Metav IndustryLine pin gauges from Metav Werkzeuge for dependable workshop measurement—contact our specialists via info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and ordering support. Technical Data Article number: M323.D51 GTIN: 4061905067013 Manufacturer: Metav IndustryLine Weight: 0.1 kg Core specifications Nominal diameter: 13.51 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Category: Gauge pin (Messstifte) Special features Material: special steel Workshop version (robust execution) Delivered in protective case Suitable for end‑measure and gauge setting FAQ What applications suit this gauge pin best? This gauge pin is ideal for end‑measure inspection, plug checks and gauge setting in workshop and production environments; the Metav IndustryLine pin gauge M323.D51 is optimised for small components and fixture checks. Is the nominal diameter exactly 13.51 mm? Yes, the pin is specified as 13.51 mm nominal diameter and is manufactured to an accuracy of ±0.002 mm to ensure a precise reference size. Does the pin come ready for use or is additional preparation required? The Metav IndustryLine pin gauge is delivered in a protective case and ready for immediate use; routine cleaning before first use is recommended to remove handling residues. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.52mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Combine 13.52 mm diameter, 50 mm length and a tight ±0.002 mm tolerance to ensure repeatable end‑measure checks and faster set‑up times; robust special steel construction suits workshop use. Order directly via Metav Werkzeuge or consult our advisors for application support. M323.D52 Gauge pin — 13.52 mm diameter, 50 mm length (Metav IndustryLine) M323.D52 Gauge pin is a single precision pin for end‑measure verification and fixture alignment in inspection and production environments Single 13.52 mm gauge pin Length 50 mm for deep bore checks High repeatability with ±0.002 mm tolerance Workshop version for daily use Repeatable measurements that reduce downtime The compact geometry and the nominal 13.52 mm diameter, combined with a ±0.002 mm specification, make this pin a reliable reference for end‑measurements and go/no‑go verifications. Built to deliver consistent contact geometry over repeated cycles, the component helps to reduce measurement scatter and downstream rework. The controlled tolerance translates directly into fewer set‑up iterations on production lines and a steadier output quality in inspection routines. Durable construction for everyday workshop conditions Manufactured from special steel and supplied in a workshop configuration, the pin stands up to routine handling and frequent insertion cycles. The 50 mm length offers sufficient engagement for many fixture and bore checks while remaining compact for easy storage. The weight and balance support stable seating during measurement, which contributes to consistent readings and a longer service life under regular shopfloor conditions. Straightforward use across inspection and assembly tasks As a single precision test pin, the item is suitable for end‑measure checks, gauge setting and fixture verification across inspection, assembly and production stages. The simple, single‑piece design ensures fast positioning and minimal adjustment time, allowing teams to maintain throughput without sacrificing measurement confidence. Its form factor also eases integration into existing gauge sets and modular test fixtures. Traceability and identification for process control Identification by SKU M323.D52 and GTIN is available for inventory and process traceability. The clear technical specification supports documentation in quality records and assists in maintaining consistent inspection standards across shifts. The construction and stated tolerance support the rational decision to standardise on a single reference pin where repeatable end‑measure control is essential. For precision end‑measure checks, rely on Metav IndustryLine quality—contact Metav Werkzeuge in Emmerich for ordering details and technical guidance Technical data SKU: M323.D52 GTIN: 4061905067020 ECLASS: 21170231 Facts Diameter: 13.52 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Item type: Single gauge pin Intended use: End‑measure checks, fixture alignment FAQ What applications is this gauge pin suitable for? This M323.D52 gauge pin (Metav IndustryLine) is intended for end‑measure verification, fixture alignment and gauge setting in inspection and production contexts. Is the stated ±0.002 mm accuracy sufficient for precision inspection tasks? Yes, the ±0.002 mm specification provides a high level of repeatability appropriate for precision end‑measure checks and for reducing set‑up variability in manufacturing. Which material is the pin made from and what benefit does this provide? The pin is made from special steel, which offers robust performance for daily workshop handling and prolonged engagement cycles. How is the product identified for stock and quality records? Identification is via SKU M323.D52 and GTIN 4061905067020, supporting straightforward traceability in inventory and quality documentation. Can this test pin be integrated into existing gauge sets? The single‑piece design and standard form factor make the pin easy to integrate into modular fixtures and gauge sets used for routine inspection and assembly. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.53mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the 13.53 mm diameter and ±0.002 mm tolerance in a compact, workshop-grade design to secure repeatable reference measurements; the 50 mm length offers easy handling and insertion depth for bore checks. Order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin, single 13.53 mm (50 mm length) – workshop-grade precision from Metav IndustryLine A gauge pin, single 13.53 mm (50 mm length) designed for end‑measure verification and bore checking in workshop metrology, combining compact handling with tight dimensional control Workshop-grade execution Diameter 13.53 mm with ±0.002 mm tolerance 50 mm special steel length for stable handling Single pin for reference and inspection tasks Precision that reduces uncertainty on the shop floor With a nominal diameter of 13.53 mm and a stated tolerance of ±0.002 mm, this single gauge pin functions as a stable reference for go/no‑go checks and alignment tasks. The tight tolerance limits measurement scatter and supports quality control routines where repeatability matters. Such accuracy is especially valuable in small‑bore inspection, pin gauges for fixture alignment, and final inspection steps where a compact reference element simplifies comparison to nominal values. The clear numerical specification enables straightforward inclusion in inspection protocols and process sheets. Built for regular workshop use and straightforward handling The workshop execution reflects a focus on durability and everyday usability: manufactured from special steel, the pin maintains dimensional stability during normal handling and routine use. Its 50 mm length gives sufficient insertion depth while remaining easy to manipulate by hand or with simple clamping devices. The modest mass makes the item convenient for frequent checks without adding handling fatigue, and the single‑piece design minimises features that could trap debris—helping to maintain consistent contact and reproducible results across repeated measurements. Practical applications and process benefits This single gauge pin serves several clear roles in a production environment: reference checking of bores, end‑dimension verification, and use as a datum in quick inspection jigs. As a compact reference element it speeds up routine checks, reducing machine downtime caused by lengthy measurement procedures and allowing faster decision points on accept/reject flows. The combination of a defined 13.53 mm nominal size and ±0.002 mm tolerance supports traceable in‑process control and simplifies documentation when integrating the pin into quality records or inspection plans. Choose the Metav IndustryLine gauge pin for reliable 13.53 mm reference measurement and contact Metav Werkzeuge for tailored application advice and rapid supply Technical data Article number: M323.D53 GTIN: 4061905067037 Brand: Metav IndustryLine Core dimensions Diameter: 13.53 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials & features Material: Special steel Special feature: Workshop execution Category: Gauge pins (Messstifte) Accuracy class: ±0.002 mm FAQ What is the primary use of this gauge pin? The single gauge pin M323.D53 is intended for bore checking, end‑measure verification and use as a compact reference in inspection jigs. Does the pin provide traceable tolerance information? The M323.D53 from Metav IndustryLine is specified with a tolerance of ±0.002 mm, suitable for workshop calibration and process checks; a calibration certificate can be requested if required for documentation. What material is the gauge pin made from and how does that affect use? Made from special steel, the pin offers dimensional stability under normal workshop handling and resists minor wear during routine inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.54mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of workshop-grade durability, Ø 13.54 mm sizing and a ±0.002 mm tolerance to keep inspection and fixturing tasks consistent; order the gauge pin directly via Metav Werkzeuge or consult our technicians for application advice. Gauge pin M323.D54 — Workshop inspection pin, Ø 13.54 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.D54 is a single, workshop-grade inspection pin intended for dimensional checking, fixture alignment and reference gauging in production and quality-control environments Workshop-grade construction for daily use Diameter 13.54 mm for precise fit checks Tolerance ±0.002 mm for high-precision checks Reliable dimensional control for small bores and fits The pin delivers repeatable alignment and verification where tight clearances matter: with a Ø 13.54 mm diameter and 50 mm usable length, it is configured for accurate insertion and measurement of bores, dowel seats and mating parts. The specified ±0.002 mm tolerance denotes the manufacturing limit for deviation and supports reliable go/no-go assessments and comparative checks on the shop floor. This makes the pin suitable for routine inspection tasks that require consistent, quantifiable results rather than subjective judgement. Durable workshop design that suits daily handling Manufactured from special steel, the component is produced for dimensional stability and resistance under frequent use. The workshop version specification indicates a construction geared towards everyday handling and storage in industrial environments, combining practical robustness with the precise geometry necessary for insertion and withdrawal without compromising fit. As a single-unit supply, the pin is straightforward to replace or stock as a spare part in maintenance kits and inspection drawers. Traceability and simple integration into QC workflows Supplied as an individual inspection pin, the item supports clear inventory and traceability: the M323.D54 SKU and GTIN enable straightforward ordering and record keeping within quality-management systems. The compact 50 mm length eases manual handling and placement in jigs or fixtures, while the tight tolerance reduces measurement uncertainty when used as a reference or master pin. For tasks from assembly checks to in-process verification, this pin offers a low-complexity solution that aligns with standard metrology procedures. For dependable workshop measurement with Metav IndustryLine quality, request the M323.D54 gauge pin from Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for availability and technical guidance Technical Data SKU: M323.D54 GTIN: 4061905067044 Label: Prüfstift, einzeln, 13,54 mm Länge 50 mm Facts Diameter: 13.54 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Material: special steel Workshop version Supplied as single unit FAQ What applications suit this gauge pin best? The M323.D54 gauge pin is ideal for bore checking, fixture alignment and fit verification in production and inspection processes. What tolerance can be expected from this inspection pin? Tolerance is specified as ±0.002 mm, which supports high-precision checks and reproducible comparative measurements. Is the pin supplied individually or in sets? This item is supplied as a single unit, making it suitable for selective replacement or stocking as a spare part. Which material is used for the pin and why does it matter? The pin is made of special steel, chosen for dimensional stability and wear resistance under repetitive insertion and extraction. How is the item identified for ordering and traceability? The product can be ordered using SKU M323.D54 and GTIN 4061905067044 for clear traceability in inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.55mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high repeatability and compact handling thanks to the 13.55 mm diameter, ±0.002 mm tolerance and robust special steel construction; the compact gauge pin arrives in a protective transport case and can be ordered directly via Metav Werkzeuge or discussed with our technical consultants. Gauge pin M323.D55, single — 13.55 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.D55 is a workshop-grade cylindrical test pin for end-face checks, fit verification and assembly inspections in production and maintenance environments. Single gauge pin 13.55 mm diameter Workshop-grade special steel construction Precision tolerance ±0.002 mm Supplied in protective transport case Reliable fit checks for assembly and inspection A compact cylindrical test pin provides a dependable reference for go/no-go assessments and shaft-fit checks. The 13.55 mm nominal diameter with a tolerance of ±0.002 mm ensures that dimensional verifications are consistent across repeated measurements, reducing the risk of assembly rejects. The workshop design permits quick handling on the shop floor, while the solid construction keeps deformation low during routine use. This combination supports faster quality decisions and lower rework rates in mechanical assembly and maintenance operations. Consistent measurement accuracy under workshop conditions Precision is the primary rational advantage of this tool: the specified tolerance translates into measurable control for clearance and interference checks. The material selection—special steel—maintains surface integrity under frequent contact and resists wear that would otherwise alter the functional size. By using a dedicated measurement pin instead of improvised substitutes, inspection routines gain traceable repeatability and a clear pass/fail criterion, which streamlines quality documentation and speeds up throughput in production and repair tasks. Practical handling and secure storage for everyday use At 50 mm overall length the pin balances reach with manoeuvrability, making it suitable for confined assemblies as well as bench inspections. Delivery in a protective transport case preserves the finished surface and ensures safe storage between uses, so calibration drift and handling damage are minimised. The workshop-oriented configuration supports frequent deployment by technicians and inspectors, offering a robust, low-complexity solution that integrates smoothly into established inspection workflows. Contact Metav Werkzeuge for stock availability and tailored technical advice on the M323.D55 gauge pin, shipped from Emmerich with reliable supply and expert support Technical data SKU: M323.D55 GTIN: 4061905067051 Category: Messstifte Key measurements Diameter: 13.55 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.1 kg Features & materials Material: Special steel Version: Workshop execution Delivery: Protective transport case Image file: m323a01-main.jpg FAQ What checks is this gauge pin best suited for? The M323.D55 gauge pin is intended for end-face checks, fit verification and quick go/no-go assessments in assembly and inspection tasks. Is the accuracy of the pin suitable for fine mechanical work? Yes, the specified ±0.002 mm tolerance makes the M323.D55 suitable for demanding workshop inspections where tight dimensional control is required. How is the pin delivered and protected during transport? The test pin is supplied in a protective transport case to preserve the measuring surface and prevent handling damage. Can the M323.D55 be used for routine machine shop inspections? The workshop-grade construction and nominal dimensions of the M323.D55 make it practical for repetitive checks on shafts, housings and assembly fittings in machine shops. Which material is used and why does it matter? Constructed from special steel, the pin offers good surface hardness and wear resistance, maintaining dimensional stability over frequent use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.56mm Test Pin Length 50mm Workshop Version - Metav IndustryLine
Precise, compact and workshop‑graded: the combination of ±0.002 mm tolerance, 13.56 mm diameter and 50 mm length provides a reliable reference for end‑dimension verification and fixture alignment; order the test pin directly via Metav Werkzeuge or consult our specialists for application advice. Test pin, single, 13.56 mm diameter, length 50 mm (M323.D56) The Test pin, single, 13.56 mm, length 50 mm (M323.D56) serves as a precision gauge pin for end‑measure verification, alignment and plug‑gauge tasks in workshop and inspection environments Precision ±0.002 mm tolerance Diameter 13.56 mm for end‑measure checks 50 mm overall length for compact fixtures Workshop version in special steel Engineered for dependable end‑dimension verification The gauge pin is produced to a tight ±0.002 mm manufacturing tolerance, making it suitable as a reference element in repetitive inspection tasks where reproducible results are required. With a nominal diameter of 13.56 mm, the pin functions as a standardised plug for checking final dimensions and seating in bores or sockets; the narrow tolerance reduces the risk of false rejects and supports faster decision cycles on the shop floor. The construction emphasises dimensional accuracy and consistent repeatability rather than decorative finishes, which benefits quality control routines and process stability. Compact design that suits fixtures and inspection rigs At 50 mm overall length and weighing approximately 0.1 kg, the component offers a low‑profile solution for confined set‑ups and fixture blocks. The special steel composition grants mechanical robustness under frequent insertion and removal, while the short form factor helps maintain alignment integrity in tight assemblies. This compact, workshop‑grade configuration simplifies handling and reduces set‑up time compared with longer or heavier reference pins, so throughput in small‑batch inspection and jigs is improved without compromising measurement certainty. Reliable integration into production and measurement workflows Designed for straightforward use in end‑measure control, the pin complements common plug‑gauge and alignment procedures; it is appropriate for controlled checks during assembly, final inspection and part acceptance. The production tolerance and simple geometry make the element compatible with established metrology equipment and manual verification steps, providing a clear pass/fail reference or a repeatable datum. The workshop specification supports frequent, practical use where traceable results and limited handling complexity are priorities. Contact Metav Werkzeuge for ordering details or application support for the Metav IndustryLine test pin M323.D56 with 13.56 mm diameter and ±0.002 mm precision and ensure the correct reference parts are supplied for the inspection task at hand Technical Data Article number: M323.D56 GTIN: 4061905067068 Label: Test pin, single, 13.56 mm, length 50 mm Facts Diameter: 13.56 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Material: Special steel Special features Workshop version Suitable for end‑dimension verification Compact form for fixture integration FAQ What tolerance does this gauge pin provide and what does it mean for inspection? The test pin is manufactured to a ±0.002 mm tolerance; this level of precision delivers a stable reference point for end‑dimension checks and reduces measurement variability in routine inspection workflows with the Metav IndustryLine M323.D56 test pin. Is the material suitable for frequent use in a workshop environment? Yes, the M323.D56 is made from special steel and specified as a workshop version, giving mechanical resilience for repeated insertion and handling in fixtures and measurement set‑ups. Can this pin be used as a plug gauge for bore verification? The 13.56 mm diameter and tight tolerance make the pin appropriate as a plug‑type reference for bore seating and end‑measure verification within compatible inspection procedures. Does the product come with traceability or calibration documentation? The product data does not indicate supplied calibration certificates; any calibration or traceability requirements should be confirmed with Metav Werkzeuge prior to purchase to ensure alignment with specific quality system needs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.57mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
A compact gauge that combines tight dimensional control and workshop robustness: the precise 13.57 mm diameter and ±0.002 mm tolerance ensure reproducible end‑measure checks, while the 50 mm shaft and special steel construction withstand routine use; order the gauging pin directly via Metav Werkzeuge or ask the consultants for application advice. Gauging pin M323.D57 – Test pin, Ø 13.57 mm, 50 mm length (Metav IndustryLine) A gauging pin (M323.D57) designed for fast end‑dimension checks and go/no‑go inspection in workshop environments Workshop version for everyday use Diameter exactly 13.57 mm for end‑dimension checks 50 mm length for stable engagement Accuracy ±0.002 mm for reproducible results Precision that lowers inspection uncertainty The inspection pin delivers a reliably repeatable reference with a stated accuracy of ±0.002 mm, making it suitable where small deviations affect assembly or fit. The defined 13.57 mm measuring dimension is provided as a fixed end‑measure, reducing interpretation in routine checks and accelerating process control. Using a dedicated gauging element simplifies decision chains in quality control: the measured result is clear, the need for rework is reduced and the throughput of inspection stations is increased, which supports leaner production cycles. Robust construction for workshop routines Manufactured from special steel, the pin is configured as a workshop version that balances durability with handling comfort. The 50 mm shaft provides sufficient engagement depth for many end‑measure applications while remaining compact for fast manual use. The listed mass of 0.1 kg gives a stable feel without unnecessary bulk. Where repeated insertion and withdrawal occur, this construction reduces wear on mating surfaces and keeps replacement intervals low, which contributes to predictable maintenance planning. Practical benefits for process control As an individual test pin, this product fits into both dedicated inspection fixtures and ad‑hoc checks at the machine or assembly bench. It is intended specifically for end‑dimension verification and is therefore effective for quick go/no‑go decisions, first‑article checks and in‑process sampling. The clear numeric specification and single‑dimension design lower the operator training threshold and shorten measurement cycles, delivering a measurable productivity gain on routine inspection tasks. Traceability and workshop logistics The pin is supplied as a single item with clear identification via SKU M323.D57 and GTIN 4061905067952, which eases stock keeping and traceability in ERP systems. Delivery includes a transport case to protect the gauge in transit and storage, reflecting the workshop focus on robustness and ease of handling. The combination of distinct labelling and protective packaging supports orderly shelf management and fast retrieval during production. Contact Metav Werkzeuge for supply and application support on the Metav IndustryLine M323.D57 gauging pin—the team in Emmerich will advise on suitability and delivery options Technical data Article number: M323.D57 GTIN: 4061905067952 Manufacturer: Metav IndustryLine Core dimensions Diameter: 13.57 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Special features Material: special steel Workshop version Supplied in transport case Single, individual test pin FAQ What is the intended use of this gauge? The M323.D57 gauging pin is intended for end‑dimension checks and go/no‑go inspection in workshop and production settings where a single, clearly defined reference diameter is required. Is the diameter tolerance suitable for precision assemblies? Yes, the ±0.002 mm accuracy of the inspection pin meets the demands of tightened assembly tolerances and provides reproducible results for serial inspection. What material is the pin made from and how does that affect wear? The pin is made from special steel, chosen to provide resistance to routine wear in workshop applications while maintaining dimensional stability. Does the product include protective packaging? The gauging pin is supplied as a single item and is delivered in a transport case to protect the gauge during storage and transport. How can the M323.D57 be identified in stock systems? Identification is via SKU M323.D57 and GTIN 4061905067952, simplifying inventory control and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.58mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precise bore verification thanks to the combination of a 13.58 mm nominal diameter, tight ±0.002 mm tolerance and a 50 mm length in a robust workshop design; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.D58 — 13.58 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.D58 for precise checking of bores and fits in workshop and inspection environments. Diameter 13.58 mm precision check Dimensional tolerance ±0.002 mm 50 mm overall length for deeper bores Workshop version with protective transport box Consistent accuracy for fewer rejects and faster inspection This single test pin is manufactured for repeatable dimensional checks where reliable tolerance control matters. With a nominal diameter of 13.58 mm and a verified positional variation of ±0.002 mm, the pin supports tight go/no‑go decisions on fits and clearances. The combination of exact nominal size and low variation reduces measurement uncertainty, helping to lower scrap rates and shorten inspection cycles — a clear efficiency benefit for production and quality control. The instrument’s compact length is suited to component bores and fixtures where controlled insertion depth is required. Built for the workshop — durable handling and safe transport Designed as a workshop execution, the pin is made from special steel, giving a balance of mechanical integrity and handling robustness appropriate for everyday use at the bench or on the shop floor. Supplied as a single item with a protective transport box, the pin is easy to store and carry without risking damage in transit. The modest mass facilitates quick manual handling during repetitive checking tasks and integration into inspection jigs or assembly stations, preserving throughput without compromising on measurement stability. Simple integration into quality workflows and supplier assurance The test pin is suitable for routine verification tasks and set‑up checks in batches or fixtures, providing a straightforward physical reference that complements electronic measurement systems. The clear identification (SKU M323.D58, GTIN 4061905067969) and the workshop specification simplify procurement and inventory management. Metav’s role as a precision partner, with a broad catalogue and logistics base in Emmerich, ensures reliable supply and supportive consultancy when matching measuring hardware to particular process requirements. Contact Metav Werkzeuge for tailored advice on integrating this gauge pin into inspection routines and for delivery directly from our Emmerich quality hub Technical data SKU: M323.D58 GTIN: 4061905067969 Label: Prüfstift, einzeln, 13,58 mm Länge 50 mm Manufacturer brand: Metav IndustryLine Weight: 0.1 kg Core specifications Nominal diameter: 13.58 mm Length: 50 mm Dimensional variation: ±0.002 mm Special features Workshop version Delivered in protective transport box Material: Special steel Single test pin FAQ What nominal diameter does the pin have? The gauge pin M323.D58 has a nominal diameter of 13.58 mm. What tolerance is achieved with this test pin? The workshop pin from Metav IndustryLine is specified with a dimensional variation of ±0.002 mm. What material is used for the pin? The pin is made from special steel, supplied as a single test pin (SKU M323.D58). How is the pin supplied for transport and storage? Delivery is in a protective transport box to prevent damage during handling and transit. Can this pin be used in inspection fixtures and jigs? Yes, the 50 mm length and precise diameter make it suitable for use as a reference or checking element in fixtures and inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.59mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise small‑diameter gauging combined with rugged workshop design and reliable transport protection; the compact gauge pin streamlines end‑dimension checks and reduces inspection rework. Order the item directly via Metav Werkzeuge or consult our specialists for application advice. Test pin M323.D59 — Gauge pin, 13.59 mm diameter, 50 mm length (Metav IndustryLine) A Test pin M323.D59 designed for precise end‑dimension verification and use in workshop jigs and inspection fixtures. Workshop version for industrial use Tolerance ±0.002 mm for fine repeatability Diameter 13.59 mm, length 50 mm Precision where small differences matter The compact gauge pin delivers high precision for measurement tasks in which millimetre fractions decide accept/reject outcomes. With a nominal diameter of 13.59 mm and a declared accuracy of ±0.002 mm, this pin is classified for the micro measurement range suitable for fine mechanical work; that classification reflects the balance between minimal probe deflection and the reach required for typical small components. The immediate benefit is faster, reproducible inspection: fewer ambiguous readings, fewer rework cycles and a clearer quality record for serial checks. Built to withstand workshop routines Manufactured from special steel and specified as a workshop version, the pin combines corrosion‑resistant durability with dimensional stability under frequent handling. A 50 mm shaft length provides sufficient engagement for end‑dimension checks while remaining easy to seat in chimed holders or simple fixtures. Supplied in a transport case, the component arrives protected against knocks and contamination, reducing the time needed to prepare inspection tools and preserving the pin’s metrological condition between uses. Practical integration in inspection setups The gauge pin is intended for end‑dimension and positional checking in jigs, go/no‑go fixtures and single‑point inspection tools. Its compact form factor supports quick replacement and low‑effort alignment in series testing, which increases throughput in repetitive QA tasks. Where traceable calibration is required, the listing does not include a calibration certificate; nevertheless, the pin’s combination of nominal diameter and fine tolerance makes it a reliable reference element for shop‑floor control and batch sampling processes. For workshop‑grade, small‑diameter gauging rely on Metav IndustryLine’s test pin M323.D59 — contact Metav Werkzeuge for availability and supply from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: M323.D59 GTIN: 4061905067976 Manufacturer: Metav IndustryLine Weight: 0.1 kg Facts Diameter: 13.59 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Material: Special steel Special features Workshop version Supplied in transport case for protection Intended use: end‑dimension checks Measurement category: Micro (10–100 mm range) FAQ What tolerance does the gauge pin offer? The Test pin M323.D59 (Metav IndustryLine) is specified with a tolerance of ±0.002 mm, suitable for fine workshop inspections. Is the pin supplied ready for transport and storage? The item is delivered in a transport case to protect the gauge pin during handling and transit. Which applications suit this pin best? Its design targets end‑dimension verification, quick go/no‑go fixtures and small‑component checks in workshop and production environments. What material is used for the pin and how does it behave under use? The gauge pin is made from special steel, selected for dimensional stability and resistance to everyday workshop influences. Is a calibration certificate included with the product? The product listing does not include a calibration certificate; the standard delivery comprises the gauge pin and transport case. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.5mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of high-precision tolerance (±0.002 mm), 13.5 mm diameter and robust special-steel construction for repeatable go/no-go checks on workshop gauges; supplied as a workshop-grade part with transport case for safe handling — order or consult Metav Werkzeuge for application advice. Gauge pin, single, Ø13.5 mm, length 50 mm (M323.D50) — Metav IndustryLine Gauge pin M323.D50 is a single plug gauge pin designed for end‑limit checks and precise reference measurements in jigs and fixtures High-precision tolerance ±0.002 mm Diameter 13.5 mm, length 50 mm Special-steel construction Workshop version, transport case included Precision that reduces rework and inspection time For repetitive dimensional checks the primary benefit is predictable accuracy: the pin’s tolerance of ±0.002 mm minimises ambiguity in pass/fail tasks and reduces downstream rework. Compact and purpose-built for workshop use, the solid cylindrical design provides a stable reference that integrates easily into measuring fixtures and checking assemblies. The tight tolerance translates directly into fewer ambiguous decisions on the shop floor, which improves throughput in batch inspections and speeds routine quality gates without adding complexity to existing processes. Robust material and handling for heavy use Constructed from special steel, this gauge pin resists wear and maintains form under frequent insertion cycles, extending service life compared with untreated pins. The workshop version specification means the finish and hardening balance durability with practical handling; the result is a component that performs consistently in demanding environments. Supplied in a transport case, the pin arrives protected from damage in transit and is ready for immediate use or secure storage between shifts, preserving calibration and minimising downtime for replacements. Practical application and compatibility with inspection workflows Engineered as a simple, reliable reference for go/no‑go checks and alignment tasks, the single gauge pin matches common workshop routines where end‑measurements and fitting checks are required. The cylindrical form and standard diameter make it straightforward to pair with bore gauges, alignment fixtures or comparator setups. Marked with the SKU M323.D50, the component suits production and maintenance environments where small, repeatable gauges are used to confirm assembly tolerances or to check tooling runs quickly without elaborate setup. Contact Metav Werkzeuge for tailored advice and secure immediate supply of the M323.D50 gauge pin for your inspection tasks Technical Data Article number: M323.D50 GTIN: 4061905066290 Material: Special steel Diameter: 13.5 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Facts Category: Gauge pins Single, plain cylindrical design Workshop-grade finish Transport case for delivery Special features Suitable for fixture and jig checks Durable against repeated insertion cycles Compact for easy storage and handling SKU marking for inventory control FAQ What tolerance can be expected from this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, providing high repeatability for go/no‑go checks and reference measurements in workshop applications. Which materials is the pin suitable for checking? As a dimensional reference, the pin itself is made from special steel; it is intended for use in verifying bores, seats and alignment features across typical metallic components. Is the M323.D50 ready for immediate use upon delivery? Yes, the M323.D50 is supplied as a workshop version and arrives in a transport case, protected for immediate deployment or safe storage without additional packaging work. How does the M323.D50 support production efficiency? By offering a compact, precisely made reference with a tight tolerance, the pin reduces ambiguity in inspection steps, speeds routine checks and lowers the risk of rework in serial production. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.61mm Gauge Pin, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from workshop-grade robustness, ±0.002 mm verification accuracy and a compact 13.61 mm reference diameter for repeatable go/no‑go checks; order the gauge pin directly via Metav Werkzeuge or request guidance from our consultants. Gauge pin M323.D61 — single gauge pin, 13.61 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.D61 is a single reference pin designed for precise fit checks and dimensional verification in workshop and inspection environments Workshop-grade construction for daily use Diameter 13.61 mm for precision fits Length 50 mm with robust special steel Tolerance ±0.002 mm for tight verification Precise verification that speeds approval processes The compact reference diameter and tight tolerance make this pin a reliable instrument for repeatable acceptance checks. With a nominal diameter of 13.61 mm and a verified tolerance of ±0.002 mm, the component supports decisive go/no‑go evaluations and reduces measurement uncertainty during routine inspections. This direct performance data helps to shorten decision loops in quality control and to maintain consistent assembly tolerances across batches. Workshop-ready build for frequent handling Built as a workshop version, the pin is manufactured from special steel and configured for everyday use where robustness and handling matter. The 50 mm length provides secure engagement with small assemblies while keeping the tool compact for rapid exchange on benches. Supplied ready for transport in a protective case, the item is dimensionally stable and simple to store between shifts, supporting continuous operation without time‑consuming setup. Designed for small-part inspection and precision fits Classified in the micro range (measurement span around 10–100 mm), this reference pin is suitable for fine mechanical tasks such as connector seating checks, small bearing trials and precision mating tests. Its compact geometry combines stiffness with accessibility for confined spaces, making it well suited to inspection benches, jig stations and final acceptance routines. The combination of material choice and dimensional accuracy supports reliable checks that integrate directly into standard workshop workflows. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to secure the M323.D61 and discuss application suitability via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.D61 GTIN: 4061905067990 Material: Special steel Diameter: 13.61 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Delivery: Transport case included Facts Nominal diameter: 13.61 mm Measurement range: 13.61 mm Length: 50 mm Weight: 0.1 kg Resolution / accuracy class: ±0.002 mm Special features Workshop version Robust special steel construction Compact geometry for small components SKU: M323.D61 FAQ What is the intended use for this gauge pin? The gauge pin M323.D61 is intended for fit checks, go/no‑go verification and dimensional confirmation of small components in workshop and inspection settings. Is the material corrosion‑resistant? The pin is made from special steel; specific corrosion properties depend on the alloy treatment and environment, so storage in the supplied protective case is recommended. How precise is the pin for dimensional checks? The pin is manufactured to a tolerance of ±0.002 mm, making it suitable for tight verification tolerances in quality control. Can this gauge pin be used in confined assemblies? Yes. The 50 mm length and compact diameter are designed to access confined areas and to support checks on small assemblies and connectors. Does the product come with a transport or storage solution? The M323.D61 is supplied with a protective transport case to simplify handling and safe storage between uses. Is this part suitable for serial inspection workflows? Yes. The workshop design and repeatable dimensional accuracy make the pin appropriate for serial inspection and routine quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.62mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact 13.62 mm diameter and a 50 mm length in a rugged workshop version, manufactured from special steel and finished to a tight ±0.002 mm tolerance; the result is a reliable gauge pin that keeps inspection cycles short and rejects low. Order the test pin directly via Metav Werkzeuge or contact our consultants for specification checks. Test pin M323.D62 — workshop test pin, Ø 13.62 mm, 50 mm length Test pin M323.D62 for end‑dimension checks and fixture gauging in workshop and inspection environments. Workshop version, robust design Diameter 13.62 mm for precise gauging Length 50 mm for standard fixtures Tolerance ±0.002 mm ensures tight accuracy Reliable accuracy for daily inspection tasks A compact gauge pin that prioritises precision for routine measurement work: the diameter of 13.62 mm and the manufacturing tolerance of ±0.002 mm deliver reproducible results when inspecting end dimensions or confirming fit within assemblies. Machined from special steel, the component resists wear and maintains contact geometry over repeated cycles, which reduces the need for frequent replacements and supports a steady quality flow on the shop floor. Compact design for fixture and gauge compatibility The moderate 50 mm length and standard diameter make this measuring pin suitable for common jigs, plug gauges and handheld verification tools; it slips into existing set‑ups without custom adapters. The workshop version is optimised for handling and resilience rather than delicate laboratory storage, and the item is supplied in a protective transport box to safeguard the measuring face during transit. Such packaging helps preserve the pin’s geometry until the moment of use. Integration into efficient workshop routines Built for fast repeatability, the gauge pin reduces adjustment time and simplifies go/no‑go checks in production and maintenance workflows. As part of the Metav IndustryLine range, the component benefits from a robust supply chain and consistent quality control, which supports predictable stock and fast replenishment when instruments wear. Technical teams benefit from a low‑complexity replacement policy and straightforward interchangeability with matching fixtures and gauges. For workshop-ready precision from Metav IndustryLine, request availability and tailored advice from Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.D62 GTIN: 4061905068003 Manufacturer: Metav IndustryLine Facts Diameter: 13.62 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Supplied in transport box Intended for end-dimension checks and gauging FAQ What tolerance does the test pin offer? The test pin is manufactured to a tolerance of ±0.002 mm, providing the close dimensional control required for workshop gauging. Which material is used for this gauge pin? This gauge pin is made from special steel to ensure wear resistance and long service life in routine inspection tasks. What are the main applications for this measuring pin? The measuring pin is intended for end‑dimension checks, fixture verification and plug gauge applications in production and maintenance. Is the pin compatible with standard fixtures? The 13.62 mm diameter and 50 mm length were chosen for compatibility with common fixtures and gauges, allowing simple integration into existing setups. How is the item packaged for delivery? The pin is supplied protected in a transport box to preserve the measuring faces during storage and shipment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.63mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of workshop-ready robustness, traceable precision and compact handling to speed up inspection routines and reduce rework; order the gauge pin directly via Metav Werkzeuge or consult Metav’s specialists for application advice. Gauge pin M323.D63 – Ø 13.63 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.D63 is a single precision test pin intended for end-dimension checks and hole gauging in workshop and metrology settings. Precision tolerance ±0.002 mm Diameter Ø 13.63 mm for accurate gauging Hardened special-steel construction Precision that keeps production moving The gauge pin is manufactured for precision inspection tasks where repeatable results matter. With a specified tolerance of ±0.002 mm, the pin supports fine dimensional checks that reduce the risk of rejected parts or costly rework. The nominal diameter Ø 13.63 mm matches common hole sizes, enabling straightforward verification of bores and plug fits. For operators and quality engineers, the measurable benefit is lower scrap rates and faster go/no-go decisions thanks to consistently narrow uncertainty margins. Workshop-ready design for practical use Designed as a single test pin for hands-on inspection, this tool combines a 50 mm length with a compact form that is easy to handle and position in production environments. The special steel construction provides wear resistance and dimensional stability during repeated use, so calibration intervals can be extended compared with softer materials. The workshop version is optimised for routine checks on assemblies and components, helping technicians complete verification steps quickly without compromising on accuracy. Seamless fit into quality workflows The M323.D63 integrates simply into established inspection procedures and jigs, making it suitable for incoming inspection, in-process checks and final dimensional control. Supplied as a single, labelled pin, it supports traceable measurements when recorded in inspection logs and contributes to a consistent quality culture on the shop floor. Sourcing from Metav IndustryLine ensures access to a wide range of complementary measurement aids and fast replenishment from Metav Werkzeuge, shortening procurement cycles and keeping production lines supplied. Choose Metav IndustryLine gauge pins via Metav Werkzeuge for traceable precision and straightforward supply — contact Metav Werkzeuge for technical advice or to request the gauge pin M323.D63 Technical Data Article number: M323.D63 GTIN: 4061905068010 Brand: Metav IndustryLine Numbers / Core technical data Diameter: 13.63 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features / Design Single test pin Workshop design Material: special steel Application: end-dimension checks, hole gauging FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.D63 is specified with a tolerance of ±0.002 mm, suitable for precision inspection tasks requiring close dimensional control. Which materials is the pin suitable for checking? As a measurement artefact, the pin itself is made of special steel and is used to inspect holes and fits in a wide range of component materials; the pin verifies dimensions rather than cutting or shaping materials. Is the gauge pin supplied individually or as a set? This article is supplied as a single test pin (single unit) and is intended for direct use in inspection routines or as a reference piece. Can the pin be used for plug-fitting tests and go/no-go checks? Yes, the gauge pin is suitable for plug-fitting checks and for use within go/no-go procedures when incorporated into the appropriate inspection jigs. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.64mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of high dimensional accuracy (±0.002 mm), workshop‑grade design, and protected delivery in a transport case for dependable inspection results; order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin M323.D64 — Precision gauge pin, Ø 13.64 mm, length 50 mm (Metav IndustryLine) The gauge pin M323.D64 is a single precision checking pin intended for dimensional inspection and end‑measure verification in workshop and quality‑control environments Workshop-grade design for robust use Diameter 13.64 mm with ±0.002 mm accuracy Length 50 mm for end‑measure verification Precision where repeatability matters A compact measuring reference, this checking pin delivers ±0.002 mm dimensional accuracy, which supports tight tolerance control during fit and end‑measure checks. The defined diameter of 13.64 mm provides a stable datum for quick go/no‑go assessments and reference comparisons on production benches. By using a fixed‑size reference pin, measurement variability is reduced and inspection throughput is increased, enabling faster decision making in production control without compromising traceability. Built for the workshop — robust and reliable Manufactured from special steel, the pin is offered in a workshop‑grade execution that balances durability with dimensional stability. The 50 mm shank provides sufficient engagement for end‑measure tasks while remaining easy to handle during repetitive checks. Delivered individually and protected for transport, the component is ready for immediate use in inspection fixtures or hand‑held verification routines, ensuring low downtime between setup and measurement. Practical application and efficiency gains The test pin performs as a reliable reference for manual inspection, fixture verification and rapid fit trials in assembly or maintenance workflows. Its single‑piece design simplifies inventory and replacement logic, while the narrow tolerance reduces the need for repeat measurements and rework. For operations seeking to streamline quality checks, the pin offers a practical combination of precision, robustness, and straightforward integration into existing inspection zones. For precision end‑measure verification, specify the Metav IndustryLine gauge pin M323.D64 through Metav Werkzeuge — contact our Emmerich team for product matching and delivery options Technical Data Article number: M323.D64 GTIN: 4061905068997 Brand: Metav IndustryLine Facts Diameter: 13.64 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Delivered in transport case Single checking pin FAQ What tolerance can be expected from this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, making the Metav IndustryLine M323.D64 suitable for precise end‑measure verification. Which materials is the pin made from? This test pin is produced from special steel, offering a balance of dimensional stability and workshop durability. How is the pin supplied for transport and storage? The M323.D64 is delivered individually and protected in a transport case to prevent damage during handling and transit. What typical tasks is the pin suited for in quality control? The checking pin is intended for dimensional inspection, fit trials and end‑measure checks on production benches and fixtures. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.65mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of tight dimensional control with a 13.65 mm diameter test pin manufactured in special steel and finished to a ±0.002 mm tolerance; the compact 50 mm length makes it ideal for routine end‑measure verification. Order the item directly via Metav Werkzeuge or ask our consultants for application advice. M323.D65 gauge pin — 13.65 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.D65 for precise end‑measurement checks and workshop inspection tasks Workshop‑grade design Ø 13.65 mm nominal 50 mm overall length Tolerance ±0.002 mm Precision where small tolerances matter The compact test pin delivers repeatable dimensional checks for end‑measure verification, combining a 13.65 mm nominal diameter with a certified ±0.002 mm tolerance. Such specification supports efficient quality control by reducing rework and lowering measurement uncertainty during pass/fail assessments. The tight tolerance is particularly useful for short production runs or in‑process inspection where small deviations have immediate downstream effects, enabling faster decision‑making and more consistent part acceptance rates. Durable construction for everyday workshop use Manufactured from special steel and executed for workshop conditions, this single test pin balances stiffness and handling convenience in a 50 mm overall length. The material choice provides wear resistance during repeated seating in fixture bores and maintains surface integrity over numerous inspection cycles. At approximately 0.1 kg, the pin is easy to position in gauges and jigs while offering the mass needed for stable contact during verification tasks, minimising measurement error caused by movement. Designed for straightforward integration into inspection routines The compact format and clear identification make the product simple to incorporate into existing inspection benches and fixture systems. Traceability is supported through the SKU and GTIN, aiding inventory control and audit trails within production quality workflows. The pin is supplied as a single unit intended for end‑measure checks and is particularly suited to workshops that require reliable, repeatable small‑diameter verification without complex handling or calibration regimes. For workshop‑ready precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for tailored advice and supply via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: M323.D65 GTIN: 4061905069000 Label: Gauge pin, single, 13.65 mm, length 50 mm Facts Diameter: 13.65 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop execution Single test pin for end‑measure verification High‑precision finishing FAQ What tolerance does this gauge pin provide? The Metav IndustryLine M323.D65 gauge pin is finished to a ±0.002 mm tolerance, suitable for tight end‑measure verification tasks. What material is the pin made from? The pin is manufactured from special steel, chosen for wear resistance and suitability for frequent use in workshop inspection. Which tasks is this pin best suited for? This compact gauge pin is intended for end‑measurement checks, final size verification and plug‑type inspections in workshop and small‑series production. Can the pin be used in standard fixture gauges and test benches? Yes, the 50 mm overall length and 13.65 mm diameter make the pin compatible with common fixture setups and bench gauges designed for short‑range verification. How is the item identified for procurement and traceability? Identification is via SKU M323.D65 and GTIN 4061905069000 for stock control and audit purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com