140mm 10x10mm Right-Hand Indexable Grooving Tool Carbide P25/P30, 3mm Cut Width - Werner Wilke Zerspanungstechnik GmbH
Reliable chip control from carbide P25/P30 tips and a compact 10 x 10 mm cross-section ensure consistent right-hand turning performance; combine robust diamond-ground cutting plates with a 140 mm overall length for flexible toolholder compatibility — order directly via Metav Werkzeuge or consult our specialists for application advice. Hook turning tool WN263 – carbide P25/P30, 10 x 10 mm by Werner Wilke The Hook turning tool WN263 is a right-hand turning tool designed for precise internal and external profiling and grooving on conventional lathes and CNC turning centres. Solid carbide P25/P30 cutting tips 10 x 10 mm cross-section for standard toolholders Right-hand cutting direction for conventional turning 3 mm grooving width suitable for narrow cuts Precise cutting and reliable edge life for production use The combination of carbide P25/P30 cutting plates and a diamond-ground finish delivers a stable cutting edge that resists abrasion and maintains geometry over many passes. The design focuses on repeatable results in production environments where small variances in tool life can multiply into significant downtime. The 10 x 10 mm cross-section fits common mini toolholders, while the overall length of 140 mm provides sufficient reach for most toolpost setups. These attributes translate into fewer tool changes, reduced machine stops and steadier component tolerances. Designed for narrow grooving and controlled chip flow Equipped with a dedicated 3 mm grooving capability and a right-hand cut orientation, the tool enables clean entry and exit on narrow profiles, reducing burr formation and secondary finishing. The steel shank fitted with diamond-ground carbide cutting plates combines the rigidity of a stable holder with the wear resistance of premium carbide. In practice, this means cleaner surfaces and less reworking – a direct benefit for workshops aiming to improve throughput and surface quality on turned parts. Practical compatibility and workshop logistics The tool is supplied in a pack of 5, which supports batch replenishment without frequent ordering. Marked as WN263, the designation helps with straightforward inventory management and tool surface matching across toolrooms. The compact cross-section ensures compatibility with a wide range of clamping systems, and the robust carbide grade is suitable for general-purpose turning of common engineering materials. Where indexable or replaceable cutting plates are preferred, the diamond-ground finish aids consistent seating and alignment, simplifying insert changes and maintenance routines. Contact Metav Werkzeuge for matching toolholders, delivery options from Emmerich and expert advice on integrating the WN263 into production workflows. Technical data Article number: 4118660052NW Item name: Hakendrehmeißel 10x10mm HM P25/P30 re. Wilke Norm/designation: WN263 Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Total length: 140 mm Cross-section: 10 x 10 mm Grooving width: 3 mm Packaging unit: 5 Special features Carbide grade: P25/P30 Right-hand cutting direction Steel shank with diamond-ground carbide cutting plates Suitable for profiling and narrow grooving FAQ What applications suit this hook turning tool? The hook turning tool WN263 by Werner Wilke is intended for narrow grooving and finishing profiles where a 3 mm cut width and a right-hand orientation are required, offering good edge stability for serial turning tasks. Is the cutting material solid carbide or an insert system? This product features carbide P25/P30 cutting plates mounted on a steel shank; the cutting edges are diamond-ground to ensure consistent seating and long tool life. Which toolholders are compatible with the 10 x 10 mm cross-section? Standard mini toolholders and compact clamping blocks that accept a 10 x 10 mm shank are compatible; this geometry enables flexible mounting in common lathe toolposts. How should the WN263 be stored to preserve the diamond-ground edges? Store the tools in their original packaging and avoid contact between cutting edges to maintain the diamond-ground surface; the pack of 5 supports organised stock rotation. Can the WN263 be used on hardened steels? The P25/P30 carbide grades are optimised for general turning and finishing; verify material-specific suitability against tool data sheets and machining parameters for hardened materials. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
140mm 25 x 25 Side Turning Tool Carbide P25/P30, Offset, DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of an offset shank, carbide P25/P30 cutting plates and DIN 4980 compatibility for reliable, precise external turning operations; order directly via Metav Werkzeuge or contact our advisors for specification support. Side-turning tool DIN 4980 (ISO 6), 25 x 25 mm, carbide P25/P30 by Werner Wilke The side-turning tool DIN 4980 (ISO 6) 25 x 25 mm is an offset, right-hand external turning tool designed for use in standard DIN 4980 (ISO 6) toolholders, suitable for precision lathe operations. Carbide P25/P30 inserts fitted Offset shank for clearance DIN 4980 (ISO 6) shank form 25 x 25 mm cross-section Precision external turning with robust carbide inserts The side-turning tool combines a steel shank with diamond-ground carbide cutting plates in grade P25/P30, yielding consistent cutting edges and predictable wear characteristics. The diamond grinding on the inserts improves surface contact and reduces the need for frequent adjustment, which translates into shorter setup times and steadier part finish during batch production. With an overall length of 140 mm and a clear 25 x 25 mm cross-section, the tool suits standard holders while offering the rigidity required for moderate to demanding external turning. The right-hand cutting direction is specified for typical lathe feed directions and avoids ambiguity during tool selection. Seamless compatibility with DIN 4980 toolholders Designed to the DIN 4980 (ISO 6) shank form and presented as an offset (abgesetzt) variant, the tool integrates directly with widely used lathe toolposts and indexable systems that accept this standard. Compatibility with the DIN 4980 standard simplifies procurement and replacement planning in production environments where interchangeability is essential. The offset geometry provides the necessary clearance between the cutting edge and workpiece shoulders or fixtures, reducing the risk of collision and enabling easier access to stepped profiles or close-to-flange turning tasks. The combination of standardised shank form and defined cross-section supports stable clamping and repeatable tool resets. Built for repeatable production and ergonomic handling A steel shank fitted with replaceable, diamond-ground carbide plates keeps maintenance straightforward: worn inserts can be exchanged without replacing the entire toolholder. The tool’s construction supports consistent repeatability in serial production, helping to reduce scrap and rework. Its format and balance aid in operator handling when mounting or changing tools, and the defined cross-section (25 x 25 mm) provides a robust contact surface in the toolholder, limiting vibration and enhancing surface finish. These attributes make the tool a pragmatic choice for workshops seeking durable, easy-to-service turning solutions. Material guidance and application overview The cutting plates are specified as carbide P25/P30, industrial grades suited to a broad range of turning tasks on steels and similar materials. The designation indicates a robust carbide grade intended for general steel machining operations while maintaining edge stability; diamond grinding improves chip control and edge conformity. As a right-hand, offset side-turning tool, it is optimised for conventional lathe feeds and external profiling; however, compatibility with specific steels, alloys or advanced materials depends on cutting parameters, insert geometry and machine rigidity. For tailored setup recommendations and cutting data, technical consultation is available to match tool grade and machining strategy to the intended application. For precision external turning with proven carbide inserts, request availability from Metav Werkzeuge and benefit from expert selection and fast supply from Emmerich. Technical data Article number: 4118640252NW Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 140 mm Cross-section: 25 x 25 mm Packaging unit: 3 Special features Carbide: P25/P30 Offset shank (abgesetzt) DIN 4980 (ISO 6) shank form Steel shank fitted with diamond-ground carbide inserts Right-hand cutting FAQ What material are the cutting plates made of? The cutting plates are manufactured from carbide P25/P30, supplied on the side-turning tool by Werner Wilke Zerspanungstechnik GmbH for stable cutting performance. Is this tool compatible with DIN 4980 toolholders? Yes, the tool follows the DIN 4980 (ISO 6) shank form, ensuring compatibility with holders that accept this standard shank profile. What are the dimensions and form of the tool shank? The side-turning tool has a 25 x 25 mm cross-section and an overall length of 140 mm, provided in an offset form for improved clearance. Can the cutting plates be replaced? The tool uses replaceable, diamond-ground carbide inserts in grade P25/P30, allowing replacement of worn plates without removing the shank from the machine. Is this tool suitable for left-hand turning tasks? This specific tool is specified as right-hand cutting; for left-hand operations a corresponding left-hand variant should be selected. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
140mm 25x16mm Grooving Tool Carbide P25/P30 6mm Cut Width, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
High-precision parting with robust carbide and standardised fitting ensures reliable production cycles; benefit from the combination of carbide P25/P30 cutting plates, a 25 x 16 mm cross-section and a precise 6 mm parting width for repeatable results. Order the tool directly via Metav Werkzeuge or request tailored advice from our consultants. Wilke parting tool (25 x 16 mm) – Carbide P25/P30, DIN 4981 (ISO 7) Wilke parting tool (25 x 16 mm) is a right-hand, carbide-equipped cut-off tool engineered for precise parting and grooving tasks in standard workshop turning applications Carbide P25/P30 grades for durability DIN 4981 (ISO 7) compatible mounting Diamond-ground carbide cutting plates 6 mm parting width, right-hand cut Precision cutting for consistent parting results The tool delivers repeatable, clean parting thanks to its standardised interface and premium cutting materials. The combination of DIN 4981 (ISO 7) compliance and a compact 25 x 16 mm cross-section ensures consistent seat and alignment in compatible holders, reducing runout and vibration. With the cutting edges made from carbide P25/P30, the insert maintains edge stability under typical lathe speeds, which translates into longer tool life and fewer interruptions in production. Engineered for productivity and surface quality A steel shank fitted with diamond-ground carbide cutting plates gives a stable connection between holder and insert while promoting improved surface finish on the parted face. The defined 6 mm parting width minimises material waste and simplifies process planning for narrow grooves. The right-hand cutting direction is optimised for conventional turning directions on most lathes, enabling efficient chip breakage and steady feed rates for short-cycle and batch operations. Compatibility, handling and best-practice use The tool’s standard interface simplifies integration into existing setups that accept DIN 4981 (ISO 7) tools and holders. With an overall length of 140 mm, the geometry supports secure clamping while reducing overhang where possible. For best results, secure the shank firmly, use appropriate coolant or lubrication for the material being machined, and avoid excessive overhang to preserve edge life. The straightforward design supports both occasional workshop use and higher-frequency production runs, offering a balance of accessibility and professional performance. For availability, compatibility checks or expert recommendations on Wilke parting tools, contact Metav Werkzeuge GmbH in Emmerich or request a customised proposal via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 4118645202NW Label: Stechdrehmeißel DIN 4981ISO7 25x16mm HM P25/P30 re. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Parting tool Standard: DIN 4981 (ISO 7) Material: Hartmetall P25/P30 UID: 4118645202NW Core dimensions Overall length: 140 mm Cross-section: 25 x 16 mm Parting width: 6 mm Packaging unit: 5 Special features Right-hand cutting direction Steel shank with diamond-ground carbide cutting plates Carbide grades: P25 / P30 Designed for standard DIN 4981 (ISO 7) holders FAQ What material are the cutting plates made of? The cutting plates are made of carbide P25/P30, offering a balance of wear resistance and toughness for general turning and parting operations with the Wilke parting tool (SKU 4118645202NW). Which standard does the tool mount to? The tool complies with DIN 4981 (ISO 7), ensuring compatibility with holders and tooling systems that accept this standard interface. What is the parting width and why does it matter? The parting width is 6 mm, which determines the kerf and influences material removal, chip formation and waste; narrower widths help reduce material loss and can simplify finishing operations. Is the tool suitable for automated batch production? The combination of a steel shank, diamond-ground carbide plates and standardised mounting makes this parting tool suitable for both workshop use and higher-frequency production, provided proper clamping and cooling are observed. How long is the tool and how does that affect mounting? The overall length is 140 mm; keeping overhang minimal and ensuring rigid clamping will help maintain precision and prolong cutting edge life. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
140mm 25x25mm Side Turning Tool Carbide P25/P30 Offset Left DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Combine carbide P25/P30 cutting edges, a stepped steel shank and DIN 4980 (ISO 6) compatibility for stable, repeatable left-hand finishing; order directly via Metav Werkzeuge or ask our consultants for application advice. Wilke Side turning tool DIN 4980 (ISO 6) – 25 x 25 mm, carbide P25/P30, left-hand A Wilke Side turning tool DIN 4980 (ISO 6) designed for precision external turning and finishing on a wide range of steels, featuring a stepped shank and diamond-ground carbide cutting inserts. Carbide P25/P30 cutting edges Stepped steel shank design Left-hand cutting direction DIN 4980 (ISO 6) compatible Consistent cutting performance for production environments The tool is built around carbide P25/P30 inserts that offer a reliable balance of wear resistance and toughness, enabling longer tool life in series turning. The diamond-ground cutting faces reduce vibration at cut entry, which improves surface finish and lowers rework rates. For production lines where cycle time and repeatability matter, the combination of a robust cutting grade and a secure insert seating delivers measurable productivity gains without complex setup routines. Stability and repeatability from the stepped shank A stepped steel shank provides firm clamping and accurate register to DIN 4980 (ISO 6), reducing axial play during heavy cuts. The 25 x 25 mm cross-section gives a rigid interface with standard toolholders, helping to maintain concentricity and geometric tolerances across multiple workpieces. This mechanical stability translates into fewer rejects and steadier process windows when machining external contours or shoulder faces on turned parts. Left-hand orientation and practical handling benefits Designed for left-hand cutting operations, the tool is suitable for facing or turning directions that require opposite-hand geometry. The offset (abgesetzt) shank allows access in restricted setups where a straight shank would interfere, improving tool reach without compromising clamping integrity. This configuration simplifies tool selection for asymmetric setups and reduces the need for special fixtures. Clear specification and application guidance Conforming to DIN 4980 (ISO 6) ensures compatibility with widely used toolholder systems, making the tool straightforward to integrate into existing tooling arrays. The steel shank fitted with diamond-ground carbide inserts is intended primarily for finishing and semi-finishing on common steels; the design supports consistent surface quality and repeatable dimensions in medium- to high-volume machining operations. Technical staff unfamiliar with carbide grades will find P25/P30 a pragmatic choice for mixed-production environments. For application advice or to secure supply of the Wilke side turning tool with carbide P25/P30 inserts, contact Metav Werkzeuge in Emmerich for specialist consultation and reliable delivery Technical data Article number: 4118640702NW Product name: Wilke Side turning tool DIN 4980 (ISO 6) 25 x 25 mm left-hand Material: Carbide P25/P30 Cross-section: 25 x 25 mm Overall length: 140 mm Cutting direction: Left-hand Standard: DIN 4980 (ISO 6) Packaging unit: 3 Facts Overall length: 140 mm Cross-section: 25 x 25 mm Packaging unit: 3 Special features Steel shank with diamond-ground carbide inserts Carbide grade P25/P30 Stepped (abgesetzt) shank design Left-hand cutting orientation FAQ What materials is this side turning tool suited for? This side turning tool with carbide P25/P30 inserts is intended primarily for turning and finishing common steels; consult Metav Werkzeuge for specific material recommendations. Is the tool compatible with standard DIN 4980 toolholders? Yes, the tool conforms to DIN 4980 (ISO 6) and is compatible with toolholders designed to that standard; the stepped shank ensures secure clamping. What is the cross-section and overall length of the tool? The tool has a 25 x 25 mm cross-section and an overall length of 140 mm, specified for stable mounting and reach in confined setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
140mm External Threading Tool 20 x 20 Carbide P25/P30 60° Right-Hand WN282 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the durable carbide P25/P30 cutting edges and the precise 60° profile for consistent external threads; the robust 20 x 20 mm shank ensures stable mounting and reliable repeatability in series production. Order directly via Metav Werkzeuge or consult the team for application-specific advice. External thread turning tool 20 x 20 mm, carbide P25/P30 – Werner Wilke The External thread turning tool 20 x 20 mm HM P25/P30 is a right‑hand, 60° profile threading solution for precision external thread turning on shaft workpieces, mounted on a solid steel shank with diamond‑ground carbide inserts. Carbide P25/P30 cutting edges 60° thread profile for exact forms 20 x 20 mm steel shank Diamond‑ground carbide inserts Accurate 60° profile for repeatable thread geometry The 60° profile is central to producing standard external threads with consistent flank geometry, reducing the need for subsequent rework. The tool’s geometry ensures the thread form is generated with high fidelity, which benefits production runs that demand uniformity. Using a defined profile reduces adjustment time at the machine and supports faster first‑part approval. Long tool life and fine surface finish from carbide grades Equipped with carbide P25/P30 cutting edges and diamond‑ground inserts, the tool offers increased wear resistance and a smooth cutting edge that promotes superior surface finish on the thread flanks. The combination of these carbide grades with a precision ground cutting face reduces edge chipping and extends the interval between indexings or insert changes, improving uptime in continuous machining operations. Compact 20 x 20 mm shank for secure clamping and straightforward integration The 20 x 20 mm cross‑section combined with an overall length of 140 mm provides a compact, rigid tooling solution that fits many standard external toolholders. The solid steel shank construction supports stable cutting conditions and minimises vibration during thread generation. Identification to WN282 simplifies integration into existing tooling assemblies and changeover documentation. Right‑hand cutting for standard turning operations and efficient cycle times Designed as a right‑hand cut tool, the turning insert is optimised for conventional lathe feed directions common in production environments. The tool’s configuration supports efficient machining cycles and predictable toolpaths, helping to reduce cycle time per part while maintaining thread accuracy. When paired with consistent setup practices, the tool contributes to repeatable output and lower scrap rates. For application guidance or to place an order referencing WN282, contact Metav Werkzeuge for tailored advice and reliable supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4118650352NW Model / Standard: WN282 Product: External thread turning tool Manufacturer (label): Werner Wilke Zerspanungstechnik GmbH Cross-section: 20 x 20 mm Overall length: 140 mm Tip angle: 60° Cutting direction: right Material: Carbide P25/P30 Packaging unit: 5 Facts Cross-section numeric: 20 x 20 Overall length numeric: 140 mm Tip angle numeric: 60° Packaging unit numeric: 5 Special features Steel shank fitted with diamond‑ground carbide inserts 60° thread profile Right‑hand cutting direction Identification: WN282 FAQ What materials is the tool suitable for? The External thread turning tool 20 x 20 mm HM P25/P30 is built with carbide P25/P30 inserts that provide wear resistance suitable for general external threading tasks; material compatibility should be confirmed for specialised alloys. Is the tool compatible with standard toolholders? The 20 x 20 mm shank and WN282 identification mean the tool is compatible with common external turning toolholders designed for 20 x 20 mm shanks. How does the 60° profile affect thread accuracy? A defined 60° profile directly reproduces the thread flank geometry, so the tool supports consistent thread form and reduces the requirement for corrective finishing operations. What are the key benefits of the diamond‑ground inserts? Diamond‑ground inserts deliver a finer cutting edge and improved surface finish on thread flanks, while also enhancing resistance to edge chipping during interrupted cuts. How is the product supplied and what is the packaging unit? The tool is supplied in packaging units of 5 and is clearly identified by SKU 4118650352NW for reordering and inventory control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
140mm Precision Turning Tool 25x25mm Carbide P25/P30 Bent Right-Hand, DIN 4972 (ISO 2) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a robust, DIN‑compliant turning solution that combines a 25 x 25 mm cross section and carbide P25/P30 cutting edges for consistent performance in general turning tasks; order directly via Metav Werkzeuge or ask the consultants for application advice. Turning tool DIN 4972 (ISO 2) 25 x 25 mm — carbide P25/P30, right‑hand, bent (Werner Wilke) A bent turning tool DIN 4972 (ISO 2) 25 x 25 mm designed for right‑hand turning, fitted with diamond‑ground carbide inserts for reliable cutting performance in workshop environments Bent design to DIN 4972 (ISO 2) Carbide grade P25/P30 inserts fitted Steel shank with diamond-ground inserts Right-hand cutting for standard turning Consistent geometry and workshop compatibility for reliable turning The bent turning tool is manufactured to DIN 4972 (ISO 2), ensuring repeatable tool geometry and straightforward mounting in standard tool holders. The 25 x 25 mm cross section and a total length of 140 mm provide a stable connection between the tool and the machine, reducing vibration and improving process reliability. With the tool fitted on a steel shank and equipped with precision diamond-ground carbide cutting plates, dimensional consistency and repeatability are prioritised, which simplifies setup and reduces measurement variation in serial production. Balanced carbide grade and cutting orientation for everyday machining Equipped with carbide P25/P30, the tool offers a considered balance between wear resistance and toughness suitable for a wide range of turning operations in workshop environments. The right‑hand cutting orientation and the bent profile improve clearance and chip flow on conventional lathes, supporting steady cutting conditions and predictable tool life. For purchasers seeking a dependable standard turning solution, this combination of geometry and carbide specification supports both finishing and general‑purpose roughing where stable cutting parameters are required. Practical benefits that keep the production line moving The design focuses on operational efficiency: the mounted carbide plates are diamond‑ground for a consistent cutting edge, which reduces the time spent on regrinding or quality checks and helps maintain surface finish. The robust shank and standardised interface contribute to lower tool change frequency and reduced machine downtime. By choosing a DIN‑compliant, carbide‑tipped turning solution, workshops gain a component that is easy to integrate into existing tooling systems while supporting predictable tool performance and process stability. Contact Metav Werkzeuge for availability and tailored technical guidance on Werner Wilke carbide turning tools — email info@metav-werkzeuge.com or call +49 2822 7131930 Product details Article number: 4118605252NW Label: Drehmeißel DIN 4972ISO2 25x25mm HM P25/P30 re. geb. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Tool type: Turning tool Configuration: bent, right-hand Dimensions & core data Cross section: 25 x 25 mm Overall length: 140 mm Packaging unit: 3 UID: 4118605252NW Materials & features Carbide: P25/P30 Steel shank with diamond-ground carbide inserts Standard: DIN 4972 (ISO 2) Bent design FAQ What standard does this turning tool conform to? The turning tool conforms to DIN 4972 (ISO 2), which defines the geometry and mounting dimensions for tools of this type (SKU 4118605252NW). Which cutting direction is provided by the tool? This item is configured for right‑hand cutting; the bent profile supports the intended chip direction and clearance for conventional lathes. What carbide grade is used and what does it mean? The tool is fitted with P25/P30 carbide plates; this grade provides a balanced combination of hardness and toughness suitable for general turning tasks in workshop environments. Are the cutting plates supplied already ground? Yes, the steel shank is fitted with diamond‑ground carbide inserts, providing a consistent cutting edge on delivery and reducing the need for immediate reconditioning. Which tool holders are compatible with this product? Compatibility aligns with the DIN 4972 (ISO 2) interface, making the tool suitable for standard holders designed for that specification Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Internal Corner Turning Tool 10x10mm Carbide P25/P30, DIN 4974 (ISO 9) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of diamond-ground carbide cutting edges, a compact 10 x 10 mm cross-section and a 150 mm overall length for precise internal profiling in restricted bores; suitable for right-hand turning applications and compatible with bores from 18 mm. Order the internal corner turning tool directly via Metav Werkzeuge or ask our consultants if needed. Internal corner turning tool DIN 4974 (ISO 9) — 10 x 10 mm, carbide P25/P30, right-hand The Internal corner turning tool DIN 4974 (ISO 9) is a purpose-built internal profiling tool fitted with diamond-ground carbide inserts for machining radii and small internal corners in bores from 18 mm. Carbide P25/P30 inserts Cross-section 10 x 10 mm Right-hand cutting orientation Minimum bore Ø 18 mm Precision and repeatability for internal finishing The tool is designed to deliver consistent internal radii and corner profiles thanks to diamond-ground carbide inserts in P25/P30 grade. These inserts are mounted on a robust steel shank, which stabilises the cutting geometry and reduces chatter at typical cutting speeds. For shops that demand reproducible results, the combination of a defined 10 x 10 mm cross-section and a standardised holder interface ensures predictable engagement with the workpiece, minimizing rework and inspection effort. The DIN 4974 (ISO 9) conformity provides a verifiable basis for integration into established machining processes. Compatibility with restricted bores and right-hand operations Engineered for internal operations, the tool requires a minimum bore diameter of 18 mm, which makes it suitable for small to medium internal profiles in components. The right-hand cutting direction and the 150 mm overall length support deep internal approaches while keeping the tool overhang manageable. For operators less familiar with bore constraints, "minimum bore Ø" refers to the smallest inside diameter where the tool can be introduced without interference; this metric is critical when selecting tooling for assemblies with internal features. Material performance and practical benefits Manufactured from carbide, the cutting inserts combine hardness and wear resistance for sustained edge life during finishing passes. The choice of P25/P30 grades balances toughness and abrasion resistance for common steels and alloyed materials. In practical terms, this means longer intervals between insert changes and predictable surface finishes, which contributes directly to process economy. Where a polished edge or tight dimensional tolerance is required, the diamond-ground geometry aids in achieving a smoother running surface and reduced burr formation. Integration into workshop workflows and quality assurance The tool’s standardised geometry and DIN compliance facilitate quick mounting and replacement within modular tool holders, supporting lean tooling setups. Traceability is simplified by the SKU and product labelling for inventory control. For purchasers seeking reliability, the combination of tried-and-tested carbide grades and a steel shank with precision-mounted inserts reduces the risk of premature wear or tool failure during internal turning operations, thereby supporting steady production output and consistent part quality. For ordering or technical advice on the P25/P30 carbide internal corner turning tool, contact Metav Werkzeuge — phone +49 2822 7131930 or email info@metav-werkzeuge.com for prompt assistance and guidance Technical data SKU: 4118615102NW Label: Inneneckdrehmeißel DIN 4974ISO9 10x10mm HM P25/30 re. Wilke UID: 4118615102NW Facts Standard: DIN 4974 (ISO 9) Cross section: 10 x 10 mm Overall length: 150 mm Minimum bore Ø: 18 mm Packaging unit: 5 Special features Material: Carbide P25/P30 Right-hand cutting direction Steel shank with diamond-ground carbide inserts FAQ What minimum bore diameter is required for use? The tool requires a minimum bore Ø of 18 mm; the Internal corner turning tool must be introduced only into bores meeting or exceeding this diameter to avoid interference. Which carbide grades are fitted to the inserts? Fitted inserts are P25/P30 grade carbide, chosen to provide a balance of toughness and wear resistance suitable for common steel and alloy applications. Is the tool suitable for deep internal profiling? Yes, the 150 mm overall length and the steel shank design permit internal profiling at moderate depths while maintaining stability for accurate finishes. What does DIN 4974 (ISO 9) mean for the user? DIN 4974 (ISO 9) indicates a standardised tool geometry and mounting interface, which simplifies replacement, holder compatibility and process documentation for the internal corner turning tool. How many pieces are supplied per package? The product is supplied in a packaging unit of 5 pieces, allowing for quick inventory replenishment and predictable usage planning. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Internal Turning Tool 10x10mm Carbide P25/P30 Right-Handed, DIN 4973 (ISO 8) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, DIN 4973 (ISO 8) compatibility and a compact 10 x 10 mm cross-section for consistent internal turning results; order directly via Metav Werkzeuge or contact our consultants for technical guidance. Innendrehmeißel (Internal turning tool) DIN 4973 (ISO 8) – 10 x 10 mm, Carbide P25/P30, right-hand by Werner Wilke The Innendrehmeißel (Internal turning tool) DIN 4973 (ISO 8) – 10 x 10 mm, Carbide P25/P30, right-hand is a compact internal turning solution designed for small-bore machining and standardised toolholder compatibility for precision metalworking. Carbide P25/P30 inserts DIN 4973 (ISO 8) compatibility Square cross-section 10 x 10 mm Suitable for bore Ø ≥ 18 mm Precision performance in confined spaces Designed for internal turning operations where access is limited, this tool delivers consistent cutting geometry in small bores. The 10 x 10 mm cross-section minimises interference while providing sufficient rigidity for fine internal profiles. Compliance with DIN 4973 (ISO 8) ensures the tool mates reliably with standard holders and adapters, reducing setup time and ensuring repeatable centring. The compact form factor and standard interface mean that the tool slotting into an existing holder requires minimal adjustment, supporting efficient batch processing and predictable tolerances. Durable cutting edge and extended service life Equipped with carbide P25/P30 cutting plates mounted on a robust steel shank, the tool balances toughness and hardness for reliable erosion and wear resistance. P25/P30 designations indicate grades optimised for a range of finishing and semi-finishing tasks, providing a superior combination of fracture toughness and abrasive resistance compared with conventional grades. The diamond-ground carbide inserts create a fine, sharp edge that reduces cutting forces and improves surface finish, which in turn lowers the need for secondary operations and increases productivity in the workshop. Seamless integration and straightforward handling The overall length of 150 mm and the standardised mounting geometry enable rapid integration into existing tool systems, helping maintain machine uptime. The tool’s right-hand cutting direction is optimised for conventional spindle rotation and common clamping arrangements, simplifying tooling lists for production runs. Because the tool follows established standards, inventory management becomes easier: holders, extensions and inserts conforming to DIN 4973 (ISO 8) will fit without custom machining, so changeover is faster and error margins in set-up are reduced. Practical advantages for workshops and small-series production Supplied in packaging units of 5 and suitable for bores from Ø 18 mm upwards, this internal turning solution supports serial workflows and repair jobs alike. The combination of carbide cutting plates and a hardened steel shank offers dependable repeatability across multiple parts, reducing scrap rates and contributing to a lower cost per part in medium-volume production. For purchasers seeking a standardised, robust option for internal turning, this tool offers clear rational benefits: predictable tool life, easy replacement of inserts and compatibility with a wide range of toolholders. For reliable internal turning with P25/P30 carbide and DIN 4973 compatibility, contact Metav Werkzeuge for ordering or technical consultation via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 4118610102NW Label: Innendrehmeißel DIN 4973ISO8 10x10mm HM P25/30 re. Wilke Standard: DIN 4973 (ISO 8) Facts Overall length: 150 mm Cross-section: 10 x 10 mm Minimum bore diameter: 18 mm Pack unit: 5 Special features Material: Hartmetall P25/P30 Right-hand cutting direction Steel shank with diamond-ground carbide cutting plates Designed for internal turning applications FAQ What minimum bore diameter is required for this tool? The tool requires a minimum bore diameter of 18 mm; the Innendrehmeißel (Internal turning tool) by Werner Wilke is specified for bores Ø 18 mm and above (SKU 4118610102NW). Which carbide grade is fitted to the inserts? The inserts are supplied in P25/P30 carbide grades, offering a balance between toughness and wear resistance suitable for internal finishing and semi-finishing operations. Is the tool compatible with standard DIN 4973 holders? Yes. The tool is manufactured to DIN 4973 (ISO 8) dimensions to ensure compatibility with standard toolholders and existing clamping systems. What is the overall length and cross-section of the tool? The tool has an overall length of 150 mm and a square cross-section of 10 x 10 mm, providing rigidity while fitting compact internal profiles. How is the cutting geometry oriented? This item features a right-hand cutting direction, which corresponds to conventional spindle rotation and standard machining setups for internal turning. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16 x 10mm Grooving Tool 4mm Cut Width Carbide P25/P30, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of durable P25/P30 carbide tips, a secure 16 x 10 mm shank, and a precise 4 mm parting width for dependable parting operations; order the tool directly via Metav Werkzeuge or consult their specialists for application guidance. Werner Wilke parting-off tool 16 x 10 mm (left-hand) — Carbide P25/P30, DIN 4981 (ISO 7) The parting-off tool is a left-hand, carbide-tipped turning tool for precise parting and grooving on lathes, designed to fit holders compliant with DIN 4981 (ISO 7). Carbide P25/P30 cutting tips DIN 4981 (ISO 7) shank form Left-hand cutting direction 4 mm parting width Engineered for reliable, repeatable parting cuts This turning insert is built around P25/P30 carbide, a grade chosen for a balance of toughness and wear resistance that suits frequent parting operations. The 16 x 10 mm cross-section of the shank provides secure clamping in standard holders, while the adherence to DIN 4981 (ISO 7) ensures interchangeability and simple replacement in compatible tool posts. The 4 mm parting width is specified for narrow, accurate cut-off work, reducing material waste and helping maintain concentricity. For machine shops seeking predictable results, the combination of standardised shank dimensions and a proven carbide grade supports consistent process setup and efficient tool management. Longer service life and fewer machine interruptions Carbide tips in P25/P30 deliver reliable wear behaviour under interrupted cutting conditions typical of parting work. The tool's construction, featuring a steel shank fitted with diamond-ground carbide cutting plates, reduces the need for frequent re-grinding and keeps changeover times low. This directly contributes to higher machine uptime and a more favourable cost-per-part scenario. Where repeatability and minimised setup time are priorities, a dedicated parting solution such as this lowers the risk of unexpected rejects and supports continuous production runs with fewer manual interventions. Practical mounting and application advantages Compatibility with the DIN 4981 (ISO 7) standard simplifies selection of suitable tool holders and ensures a solid mechanical interface. The left-hand cutting direction is ideal for operations where material feed and lathe configuration require a counterclockwise cut; specifying the correct orientation avoids fixture adjustments and preserves thread or shoulder geometry adjacent to the cut-off point. The 16 x 10 mm cross-section also aids in resisting lateral forces during parting, helping to maintain cut stability and preventing chatter, even with brief interruptions in the cut. Where this tool performs best in the workshop This tool is suited to steel and general metal parting tasks on conventional and CNC lathes where narrow, precise cuts are required. The robust carbide plates perform well in standard turning applications and support short-cycle production as well as precision one-off jobs. For precision workshops and industrial users who value interchangeability and operative reliability, the combination of standard shank form, dedicated 4 mm parting width and P25/P30 carbide provides a practical balance of performance and versatility. For specialised materials or non-standard set-ups, professional consultation is available to match tool choice to the workpiece and machine characteristics. For reliable supply and application advice on this Werner Wilke parting-off tool, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss specifications and delivery. Technical Data Article number: 4118645552NW Standard: DIN 4981 (ISO 7) Material: Carbide P25/P30 Product type: Parting-off tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Cross-section: 16 x 10 mm Overall length: 110 mm Parting width: 4 mm Cutting direction: left-hand Packaging unit: 5 Special features Steel shank with diamond-ground carbide plates Suitable for standard DIN 4981 (ISO 7) holders Designed for narrow parting and grooving operations FAQ What standard does the shank conform to? The parting-off tool conforms to DIN 4981 (ISO 7), ensuring compatibility with holders built to the same standard. Which carbide grade is used on the cutting plates? The tool is fitted with P25/P30 carbide plates, chosen for a balance of toughness and wear resistance appropriate to parting work. What is the effective cutting width of the tool? The specified parting width is 4 mm, suitable for narrow cut-off operations that require precision and minimal material loss. Is the tool right- or left-hand oriented? This variant is left-hand, intended for applications where a left-hand cut direction is required by the lathe setup. How is the tool supplied and in what quantity? The article is supplied in a packaging unit of 5, facilitating straightforward replacement planning in production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16 x 10mm Offset Carbide Turning Tool P25/P30, DIN 4978 (ISO 3) Right-Hand - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of robust cemented carbide P25/P30 cutting plates, an offset steel shank and standardised DIN conformity for consistent corner turning results; order directly via Metav Werkzeuge or consult the Metav specialists for application matching. Wilke corner turning tool DIN 4978 (ISO 3) – 16 x 10 mm, cemented carbide P25/P30, right-hand The Wilke corner turning tool DIN 4978 (ISO 3) 16 x 10 mm is an offset corner tool for precision external corner work on lathes and CNC turning centres in professional workshops and production environments Solid carbide cutting plates P25/P30 Conforms to DIN 4978 (ISO 3) 16 x 10 mm cross-section Right-hand cutting direction for external turning Precision and stability for accurate corner turning The Wilke tool combines an offset geometry with a rigid steel shank to provide consistent tool positioning and repeatable results when machining external corners. The combination of a stepped holder and diamond-ground cutting faces reduces vibration and runout, which supports precision finishes and dimensional stability in serial production. The standardised form according to DIN 4978 (ISO 3) ensures compatibility with industry fixtures and predictable cutting behaviour across setups. Durable carbide edges for predictable performance Equipped with cemented carbide P25/P30 plates, the holder delivers a balance of hardness and toughness appropriate for general turning tasks. The diamond-ground cutting surfaces promote consistent edge geometry and reliable chip formation, which helps maintain surface quality over multiple regrinds or replacements. This construction reduces unexpected tool wear and contributes to longer service intervals, aiding stable throughput in day-to-day machining. Streamlined integration into workshop tooling systems With a compact 16 x 10 mm cross-section and an overall length of 110 mm, the tool is sized for straightforward integration into standard tool posts and turret stations. The right-hand cutting orientation is suited to common external turning operations and simplifies setup when matching tool direction to spindle rotation. The modest footprint of the holder supports flexible clamping arrangements without sacrificing rigidity. Practical handling and maintenance advantages The design uses a steel shank fitted with diamond-ground cutting plates, enabling quick plate replacement and precise seating of the cutting edge. The offset form facilitates access to sharp internal corners and narrow workpiece features while preserving a secure clamping interface. Supplied in practical packaging units of five, the tool is prepared for staged tool inventories and rapid replenishment in the workshop. For secure and consistent corner turning choose the Wilke corner turning tool and contact Metav Werkzeuge for detailed application advice or to request assistance with tooling selection from the Metav specialists Technical data Article number: 4118635052NW Label: Eckdrehmeißel DIN 4978ISO3 16x10mm HM P25/P30 re. Wilke Product type: Corner turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Core data Overall length: 110 mm Cross-section: 16 x 10 mm Packaging unit: 5 Special features Material: Cemented carbide P25/P30 Offset design Steel shank with diamond-ground cutting plates Right-hand cutting direction Standard: DIN 4978 (ISO 3) FAQ What is the intended application of this corner turning tool? The corner turning tool is intended for external corner turning tasks on lathes and CNC turning centres; the Wilke corner turning tool with diamond-ground carbide plates provides consistent edge geometry for precision work. Is the cutting direction right-hand or left-hand? This tool is manufactured with a right-hand cutting direction, suited for standard external turning operations and compatible with common spindle rotations. How is the cutting plate mounted and replaced? The steel shank is fitted with diamond-ground carbide cutting plates designed for secure seating and straightforward replacement to minimise downtime during tool changes. Which standard does the tool conform to? The tool form complies with DIN 4978 (ISO 3), enabling predictable mounting and interchangeability in setups that follow the same standard. What is the package quantity for orders? The product is supplied in packaging units of five, allowing orderly stock management for workshop inventories. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16 x 16mm External Thread Turning Tool 60° Carbide P25/P30, Right-Hand - Werner Wilke Zerspanungstechnik GmbH
Achieve consistent production threads with the combination of carbide P25/P30, a 16 x 16 mm cross section and a 60° tip angle for standard metric forms — order the external thread turning tool directly via Metav Werkzeuge or consult our advisers for installation support. External thread turning tool 16 x 16 mm, carbide P25/P30, right‑hand, 60° – Wilke The External thread turning tool 16 x 16 mm, carbide P25/P30, right‑hand, 60° – Wilke is a right‑hand external threading tool designed for precision thread turning on shafts and turned parts in production environments Carbide P25/P30 grade for extended wear 16 x 16 mm cross section for secure clamping 60° tip angle for standard metric thread geometry Right‑hand cutting direction for conventional lathe set‑ups Consistent wear resistance for continuous production The combination of carbide P25/P30 inserts and diamond‑ground seating ensures predictable tool life and steady performance across production runs. The chosen carbide grade balances hardness and toughness, reducing the frequency of regrinds and downtime. For machining processes where repeatability matters, the tool’s wear characteristics translate directly into fewer interruptions and stable cycle times, supporting higher overall equipment effectiveness and lower per‑part production costs. Accurate thread form and repeatable quality A 60° tip angle provides the standard flank geometry for metric thread profiles, helping to achieve consistent fits and functional threads without additional finishing passes. The diamond‑ground cutting edges maintain their profile for precise flank angles and improved surface finish. As a result, downstream inspection and assembly tolerances are easier to meet, reducing scrap rates and improving first‑pass yield in batch or single‑piece flow production. Robust shank design for secure set‑up and vibration control The 16 x 16 mm cross section gives a compact yet rigid footprint for firm mounting in tool holders, helping to minimise deflection during engagement. The tool is supplied with a steel shank fitted with diamond‑ground carbide inserts, which simplifies insert replacement and maintains alignment. The right‑hand cutting direction matches conventional lathe feeds and set‑ups, enabling straightforward integration into existing tooling systems and quick changeover between operations. Practical use cases and maintenance clarity This external thread turning tool is suited to serial turning operations where consistent thread geometry and predictable tool life are priorities. The modular insert arrangement allows controlled maintenance: replace worn inserts rather than the whole tool body, which reduces consumable costs. Clear identification via the SKU and model facilitates inventory management and reordering in procurement systems for production and maintenance teams. For procurement of Wilke external thread turning tools or tailored technical advice on integrating carbide P25/P30 inserts into an existing workflow, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for competent supply and consultancy. Technical data Article number: 4118650302NW Model: WN282 Name: External thread turning tool 16 x 16 mm, carbide P25/P30, right‑hand, 60° Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: External thread turning tool UID: 4118650302NW Core data Overall length: 125 mm Cross section: 16 x 16 mm Tip angle: 60° Cutting direction: Right‑hand Pack size: 5 Special features Material: Carbide P25/P30 Design: Steel shank with diamond‑ground carbide inserts Execution: 60° tip angle Norm: WN282 FAQ What is the recommended thread form for this tool? The tool produces standard 60° metric thread geometry; the External thread turning tool 16 x 16 mm, carbide P25/P30, right‑hand, 60° – Wilke (SKU 4118650302NW) is set up for conventional metric profiles. Can the inserts be replaced individually? Yes, the tool uses diamond‑ground carbide inserts mounted on a steel shank; inserts can be replaced individually to extend the service life of the holder. Is this tool suitable for conventional lathe feeds? The right‑hand cutting direction matches standard lathe feed directions and is compatible with typical turning set‑ups. How does the 16 x 16 mm cross section affect performance? The 16 x 16 mm cross section offers secure clamping and stiffness, reducing deflection and improving thread accuracy in production environments. What identification should be used when reordering? Use the SKU 4118650302NW and model WN282 when reordering the Wilke external thread turning tool to ensure correct matching of carbide grade and geometry. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16 x 16mm Facing Tool Carbide P25/P30, Offset, DIN 4977 (ISO 5) - Werner Wilke Zerspanungstechnik GmbH
Combine the carbide P25/P30 cutting plates with a rigid 16 x 16 mm stepped shank and DIN 4977 conformity for consistent turning results; order the tool directly via Metav Werkzeuge or consult our technical advisors for application matching. Face turning tool (DIN 4977 / ISO 5) — 16 x 16 mm, Carbide P25/P30 by Werner Wilke Face turning tool fitted with diamond-ground carbide cutting plates, intended for right-hand lathe operations and compatible with DIN 4977 (ISO 5) toolholders Carbide P25/P30 cutting plates 16 x 16 mm shank cross-section 110 mm overall length Right-hand cutting, DIN 4977 compliant Precision and material performance for repeatable finishing The carbide P25/P30 plates provide a reliable balance between wear resistance and toughness, making this insert-equipped turning tool suitable for a broad range of steel applications. The plates are diamond-ground to a fine finish, which reduces built-up edge and improves surface quality on workpieces. This construction enhances repeatability in production environments and reduces downtime for regrinding, resulting in more predictable cycle times and consistent part quality. Stable clamping and compatibility with standard toolholders A 16 x 16 mm stepped shank and an overall length of 110 mm ensure secure clamping and good rigidity when used in standard DIN 4977 (ISO 5) toolholders. The stepped design minimises vibration and supports dimensional accuracy during face-turning operations. The tool’s right-hand cutting orientation suits common lathe setups; compatibility with established standards simplifies integration into existing tooling systems and shortens setup time on the shop floor. Economical handling and workshop advantages Equipped with carbide plates mounted on a robust steel shank, the tool lowers lifetime costs because the cutting elements are the wearing parts and are straightforward to service. The combination of a hardened carbide grade and precision mounting results in stable cutting performance under repetitive loads. The tool is particularly useful for workshops seeking a compact, standardised face-turning solution that delivers precision, easy handling and reliable results across small- and medium-batch production. Contact Metav Werkzeuge for application advice or to specify the right variant for machining requirements; Metav’s experts in Emmerich will assist with technical matching and supply logistics Technical data Article number: 4118630052NW Label: Stirndrehmeißel DIN 4977ISO5 16x16mm HM P25/P30 re. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Total length: 110 mm Cross-section: 16 x 16 mm Standard: DIN 4977 (ISO 5) Packaging unit: 5 Special features Material: Carbide P25/P30 Form: stepped shank Cutting direction: right-hand Steel shank fitted with diamond-ground carbide cutting plates FAQ What materials is this face turning tool intended for? The face turning tool is supplied with carbide P25/P30 plates, making it suitable primarily for a wide range of steels and general turning tasks where a balance of wear resistance and cutting toughness is required. Is the tool compatible with common toolholders? Yes, the tool complies with DIN 4977 (ISO 5) and is designed to fit standard holders that accept a 16 x 16 mm shank, enabling straightforward integration into existing setups. Can the carbide plates be replaced? The steel shank is fitted with diamond-ground carbide cutting plates; the design facilitates replacement of the cutting elements to restore cutting performance without replacing the entire holder. Which cutting direction does the tool support? This variant is configured for right-hand cutting, suitable for conventional lathe orientations where right-hand tools are required. What are the practical benefits in a production environment? The combination of a rigid 16 x 16 mm stepped shank, precise carbide plates and DIN 4977 standardisation delivers improved stability, reduced vibration and consistent surface finish, which helps maintain throughput and part quality. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16 x 16mm Turning Tool Broad Carbide P25/P30, DIN 4976 (ISO 4) - Werner Wilke Zerspanungstechnik GmbH
Combining carbide P25/P30 cutting geometry with a 16 x 16 mm robust cross-section and a 110 mm overall length delivers a stable, wide, straight-profile turning solution for consistent insert life and secure seating. Order the tool directly via Metav Werkzeuge or contact the advisors for application support and compatibility guidance. Turning tool DIN 4976 (ISO 4) 16 x 16 mm HM P25/P30 — Werner Wilke The Turning tool DIN 4976 (ISO 4) 16 x 16 mm HM P25/P30 is a wide, straight-profile lathe tool designed for stable mounting in standard holders and repeatable turning operations across general machining tasks Carbide P25/P30 cutting grade for durability Solid 16 x 16 mm cross-section for rigidity 110 mm overall length for standard tool posts Diamond-ground carbide insert fitted Stable carbide geometry for reliable machining results Equipped with a carbide P25/P30 cutting configuration, this wide turning tool prioritises long tool life and consistent cutting geometry. The diamond-ground cutting plate offers a precise edge and uniform flank, which results in reproducible cutting behaviour and more predictable maintenance intervals. Compliance with DIN 4976 (ISO 4) ensures compatibility with common clamping systems, so toolholders can be changed or replaced without extensive readjustment, maintaining production rhythm and reducing downtime. Rigidity and dimensions that reduce vibration and improve finishes The combination of a 16 x 16 mm cross-section and a 110 mm overall length gives a favourable stiffness-to-reach ratio that helps to minimise chatter during straight turning operations. Reduced vibration translates directly into a better surface finish and less frequent rework. The wide execution of the cutting head improves load distribution across the insert, supporting steady chip formation and consistent dimensional control in serial production environments. Secure mounting and straightforward integration into workflows A steel shank fitted with a diamond-ground carbide insert provides a secure seating surface and repeatable positioning when the insert is tightened. This construction simplifies tool change routines and supports a fast return to nominal machining parameters after maintenance or insert replacement. The straight cutting orientation helps to maintain predictable force vectors in the cut, which benefits process stability and makes the tool suitable for routine lathe setups that demand dependable, repeatable results. Contact Metav Werkzeuge for tailored advice on integrating this wide, straight carbide turning tool into the production line; Metav’s specialists in Emmerich can confirm fitment, delivery options and technical suitability via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4118625152NW Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Turning tool (Drehmeißel) Label: Drehmeißel DIN 4976ISO4 16x16mm HM P25/P30 ger. breit Wilke Dimensions & core data Overall length: 110 mm Cross-section: 16 x 16 mm Form: wide Cutting direction: straight Standard: DIN 4976 (ISO 4) Packaging unit: 5 Materials & special features Material: carbide P25/P30 Steel shank fitted with diamond-ground carbide insert Wide execution Straight-cutting orientation FAQ What standard does this turning tool comply with? This turning tool complies with DIN 4976 (ISO 4), which ensures compatibility with standard toolholders and repeatable positioning for the Turning tool DIN 4976 (ISO 4) 16 x 16 mm HM P25/P30 from Werner Wilke (SKU 4118625152NW). Which grade of cutting material is used? The tool is supplied with carbide P25/P30 cutting plates; the diamond-ground finish supports consistent geometry and wear characteristics for stable machining. What are the key dimensions for selecting a compatible holder? Select holders compatible with a 16 x 16 mm cross-section and an overall tool length of 110 mm to ensure correct seating and clamping of this tool. Is the insert permanently brazed or replaceable? The tool features a steel shank fitted with a diamond-ground carbide cutting plate; the construction is intended for secure seating and routine maintenance practices typical for carbide-tipped turning tools. How is the tool packaged for delivery? The item is supplied in packaging units of 5, as stated in the product data for the Turning tool DIN 4976 (ISO 4) 16 x 16 mm HM P25/P30 (SKU 4118625152NW). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16 x 16mm Turning Tool Carbide P25/P30 Bent Right-Hand DIN 4972 (ISO 2) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 cutting heads, a bent 16 x 16 mm profile for improved clearance, and conformity with DIN 4972 (ISO 2) for consistent set-up and efficient turning operations; order the Wilke bent turning tool directly via Metav Werkzeuge or consult our specialists for application guidance. Wilke bent turning tool – DIN 4972 (ISO 2), 16 x 16 mm, carbide P25/P30 The Wilke bent turning tool is a right‑hand, bent lathe tool designed for standard external turning tasks on lathes, offering a compact 110 mm total length and carbide cutting plates for durable performance Carbide P25/P30 cutting heads Bent profile for clearance and chip evacuation 16 x 16 mm square shank for standard tool holders Right‑hand orientation for conventional turning Precision and repeatability for everyday turning The bent turning tool combines a steel shank with diamond‑ground carbide inserts in P25/P30 grades, delivering consistent edge geometry and extended tool life. The adherence to DIN 4972 (ISO 2) ensures repeatable positioning in compatible tool posts, which minimises set‑up time and reduces scrap. This results in reliable cycle times and predictable component tolerances in small‑batch and series production alike. Geometry that improves clearance and chip control A bent design provides increased clearance between the workpiece and the toolholder, lowering the risk of interference on external contours. The right‑hand cutting orientation and the 16 x 16 mm cross‑section keep the assembly rigid, reducing tool vibration and improving surface finish. Diamond grinding of the carbide faces contributes to stable cutting edges, which supports smoother feeds and helps control chip flow during typical turning operations. Robust construction for consistent workshop performance The use of Hartmetall P25/P30 carbide in the cutting plates offers a balance between toughness and wear resistance appropriate for a wide range of turning tasks. The compact overall length of 110 mm makes the tool suitable where space is limited on the carriage, while the square 16 x 16 mm section fits common holders. Benefit here is reduced downtime: fewer tip changes and consistent cutting behaviour prolong uninterrupted production sequences. Standards, packaging and practical advantages Conformity to DIN 4972 (ISO 2) simplifies replacement and inventory management, as the tool aligns with established toolholder dimensions and clamping systems. Supplied in pack units of 5, the set‑up supports controlled stock rotation and predictable resupply. The bent execution also facilitates access to recesses and stepped turned areas where straight holders may be obstructed, improving flexibility without sacrificing stability. For tailored advice on integrating the Wilke bent turning tool into workshop processes, contact Metav Werkzeuge for a supply recommendation and delivery details at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 4118605152NW Label: Drehmeißel DIN 4972ISO2 16x16mm HM P25/P30 re. geb. Wilke Product type: Turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH SKU: 4118605152NW Specifications Total length: 110 mm Cross-section: 16 x 16 mm Standard: DIN 4972 (ISO 2) Cutting direction: Right Pack unit: 5 Materials & Features Cutting material: Carbide P25/P30 Construction: Bent design Shank: Steel shank with diamond‑ground carbide cutting plates Execution: Right‑hand turning FAQ What is the intended application for this bent turning tool? The Wilke bent turning tool (turning tool, SKU 4118605152NW) is intended for right‑hand external turning operations on lathes where a bent profile improves clearance and access to stepped contours. Which standard ensures compatibility with toolholders? Compatibility is ensured by conformity to DIN 4972 (ISO 2), which allows secure and repeatable clamping in holders designed to this standard. What is the cutting material and its benefit? The tool is fitted with carbide P25/P30 cutting plates, offering a balance of wear resistance and toughness for consistent edge life in routine turning tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16 x 16mm Turning Tool Carbide P25/P30 Straight Left-Hand DIN 4971 (ISO 1) - Werner Wilke Zerspanungstechnik GmbH
Reliable turning performance is achieved through the combination of a steel shank fitted with diamond-ground carbide inserts and adherence to DIN 4971 (ISO 1), giving consistent results in left-hand turning operations. Order supply and technical guidance via Metav Werkzeuge or consult our specialists for application advice. Wilke straight turning tool DIN 4971 (ISO 1) — 16 x 16 mm, carbide P25/P30, left-hand A Wilke straight turning tool designed for stable left-hand turning in standard holders, offering robust carbide cutting edges for repeatable machining. Straight steel shank with diamond-ground inserts Carbide grade P25/P30 for consistent edge life Conforms to DIN 4971 (ISO 1) standard Left-hand cutting for specific turning operations Precision that delivers predictable chip control and surface quality The tool combines a steel shank with diamond-ground inserts made from carbide P25/P30, providing a stable cutting geometry that supports predictable chip formation. Conformity with DIN 4971 (ISO 1) ensures compatibility with standard clamping interfaces and repeatable axial alignment, which in turn reduces setup variance and contributes to lower scrap rates. The straight form and defined cross-section support rigid mounting, improving precision in short to medium-length turning tasks. Durable cutting edges for reduced tool changes Carbide in grades P25/P30 is selected for its balance of toughness and wear resistance, which translates into longer service intervals under conventional turning conditions. The diamond grinding on the cutting inserts refines the edge microgeometry, enhancing initial sharpness and maintaining consistent cutting behaviour over time. This robustness reduces unplanned downtime and supports steadier production output, making the tool suitable for routine batch machining where predictable tool life is valued. Compact dimensions for straightforward integration With a cross-section of 16 x 16 mm and an overall length of 110 mm, the design fits common toolholders that follow DIN 4971 (ISO 1) guidelines, simplifying replacement and inventory management. The left-hand cutting orientation is intended for operations requiring reversed feed direction or specific fixture layouts. Supplied in packaging units of five, the tool is practical for small series production and maintenance stock, easing logistical planning and enabling quick replenishment when paired with Metav Werkzeuge’s centralised supply. Choose the Werner Wilke straight turning tool for dependable left-hand turning and contact Metav Werkzeuge for supply and application advice via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 4118601602NW SKU: 4118601602NW Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Turning tool Facts Cross-section: 16 x 16 mm Overall length: 110 mm Packaging unit: 5 Cutting direction: left-hand Special features Material: carbide P25/P30 Form: straight Standard: DIN 4971 (ISO 1) Steel shank with diamond-ground carbide inserts FAQ What is the intended clamping standard for this turning tool? The tool follows DIN 4971 (ISO 1), which defines the shank geometry for compatibility with standard clamping systems. Is the cutting direction left-hand or right-hand? This turning tool is specified for left-hand cutting, making it suitable for operations that require reverse feed orientation. Which carbide grade is used for the cutting inserts? The cutting edges are made from carbide P25/P30, chosen for a balance of toughness and wear resistance. What are the key dimensions to check for toolholder compatibility? Check the 16 x 16 mm cross-section and the 110 mm overall length to ensure fitment in holders compatible with DIN 4971 (ISO 1). How is the cutting edge prepared? The inserts are diamond-ground, delivering a refined edge geometry for consistent cutting behaviour. Manufacturer: Werner Wilke Zerspanungstechnik GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16 x 16mm Turning Tool Right Hand Straight Carbide P25/P30, DIN 4971 (ISO 1) - Werner Wilke Zerspanungstechnik GmbH
Combine the diamond-ground carbide cutting plates with a standardised 16 x 16 mm DIN 4971 (ISO 1) shank for dependable, repeatable turning operations; order the turning tool directly via Metav Werkzeuge or ask our consultants if needed. Turning tool DIN 4971 (ISO 1) 16 x 16 mm, carbide P25/P30 — Werner Wilke A turning tool DIN 4971 (ISO 1) 16 x 16 mm designed for right-hand external turning and general lathe applications, fitted with diamond-ground carbide cutting plates for consistent edge performance Diamond-ground carbide cutting plates Straight steel shank for secure clamping DIN 4971 (ISO 1) 16 x 16 mm shank Right-hand cutting direction Consistent cutting quality through carbide grade selection The combination of carbide P25/P30 cutting plates and a precision-ground edge delivers consistent cutting performance and improved wear resistance compared with ungraded tips. The diamond-ground finish on the cutting plates enhances the micro-geometry of the edge, reducing built-up edge and improving surface finish on turned components. This results in fewer rework cycles and steadier process windows in repetitive production, supporting a measurable productivity gain in machining routines. Reliable clamping with a standardised straight shank A straight steel shank to DIN 4971 (ISO 1) means straightforward compatibility with standard external toolholders and cross-slide mounts. The 16 x 16 mm square section provides a positive fit and stable seating, reducing vibration and runout during turning. Because the shank is straight, set-up time is minimised and alignment becomes more repeatable, which supports consistent component tolerances across batch production runs. Practical benefits of right-hand operation explained The tool’s right-hand cutting direction makes it suitable for conventional external turning tasks where the cutting action proceeds from left to right relative to the operator. In practice this means straightforward integration into typical lathe workflows and predictable chip flow. For operators less familiar with terminology: right-hand indicates the orientation of the cutting edge and the direction the tool must travel to remove material efficiently, helping to avoid mistakes during tool selection and setup. Workshop efficiency and low-maintenance handling Fitted with robust carbide plates and a hardened steel shank, this tool emphasises durability and low-maintenance handling. The solid construction and precision-ground cutting surfaces reduce the need for frequent tool changes and support longer uninterrupted runs. For procurement and workshop managers, the resulting stability helps reduce tooling inventory churn and supports leaner production planning without sacrificing cutting performance. For personalised machining guidance or to secure dependable supply, contact Metav Werkzeuge in Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss the turning tool and compatible toolholders Technical data Article number: 4118601152NW Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Turning tool Label: Drehmeißel DIN 4971ISO1 16x16mm HM P25/P30 re. ger. Wilke Numbers / Core technical data Shank cross-section: 16 x 16 mm Overall length: 110 mm Standard: DIN 4971 (ISO 1) Cutting direction: Right-hand Material (cutting plates): Carbide P25/P30 Form: Straight Special features Steel shank with diamond-ground carbide cutting plates Straight design for standard toolholders Compatible with ISO 1 / DIN 4971 holders Robust construction for repetitive turning tasks FAQ What is the shank size and standard of this lathe tool? The turning tool is supplied with a 16 x 16 mm square shank conforming to DIN 4971 (ISO 1), ensuring compatibility with standard external toolholders. Which carbide grade is fitted to the cutting plates? The cutting plates are made from carbide P25/P30, offering a balance of toughness and wear resistance suitable for general turning operations. Is this tool suitable for left-hand turning? No, this item is specified as right-hand cutting; left-hand operations require a corresponding left-hand tool geometry. How does the diamond-ground finish affect performance? The diamond-ground finish refines the cutting edge micro-geometry, improving surface finish and reducing built-up edge, which supports longer tool life and more consistent results. What is the article number for ordering and reference? The article number for this turning tool is 4118601152NW, which can be used when enquiring with Metav Werkzeuge or internal purchasing systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm 12 x 12mm Right-Hand Carbide Grooving Tool 4mm Cut Width, WN263 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a carbide-tipped hook-style turning tool that combines the wear resistance of P25/P30 carbide with diamond-ground cutting tips for precise 4 mm grooving; the right-hand cut and a 160 mm steel shank ensure stable machining and consistent surface quality. Order the tool directly via Metav Werkzeuge or consult the Metav team for application-specific advice. Hook-style turning tool 12 x 12 mm HM P25/P30, right-hand (Wilke) — turning tool for precise grooving with diamond-ground carbide tips A Hook-style turning tool 12 x 12 mm HM P25/P30, right-hand (Wilke) designed for repeatable grooving and finishing operations where tool life and surface quality matter Solid carbide P25/P30 grade Diamond-ground carbide cutting tips Right-hand cutting direction 4 mm grooving capability Consistent groove quality through premium carbide and tip geometry The combination of P25/P30 carbide and diamond-ground cutting tips delivers high wear resistance and predictable tool performance. This construction minimises edge wear and maintains cutting geometry over longer runs, which reduces rework and improves first-pass yield. The 12 x 12 mm cross-section together with the 4 mm grooving capability offers controlled chip formation and repeatable groove width, making it suitable for operations that demand consistent dimensional accuracy and surface finish. Stable tool support for reduced vibration and accurate depths A solid steel shank and a total length of 160 mm provide the rigidity required for stable cutting conditions. The WN263 specification indicates compatibility with standard holder geometries, enabling secure clamping and reduced micro-movement during cutting. The result is lower vibration, improved surface integrity and more accurate groove depths, which contributes to longer insert life and fewer rejects in serial production environments. Efficient workshop integration and predictable maintenance intervals The tool’s inserted carbide tips and standardised geometry allow straightforward replacement and integration into existing turning tool setups. Predictable wear characteristics mean maintenance intervals can be planned, reducing unplanned downtime. The right-hand cutting orientation is optimised for conventional lathe feeds and supports effective chip evacuation. For workshop procurement, the tool is supplied in practical units to support stock planning and rapid replacement when required. For reliable workshop performance and expert advice on selecting the right Wilke hook-style turning tool for specific applications, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 4118660102NW Norm: WN263 Label: Hakendrehmeißel 12x12mm HM P25/P30 re. Wilke Type: Hook-style turning tool Facts Overall length: 160 mm Cross-section: 12 x 12 mm Grooving width: 4 mm Packaging unit: 5 Special features Material: Carbide P25/P30 Cutting direction: Right-hand Steel shank with diamond-ground carbide cutting plates WN263 compatibility FAQ What materials is the tool suitable for? The hook-style turning tool with P25/P30 carbide tips is designed primarily for metal turning tasks and performs reliably when machining steels and similar materials where wear resistance is required. How wide are the grooves produced with this tool? The tool is specified for a 4 mm grooving width, providing a consistent slot dimension when used with appropriate feeds and stable clamping. Is the tool compatible with standard lathe holders? Yes, the tool’s geometry and WN263 compatibility allow secure mounting in common turning tool holders for stable operation. How are the cutting tips manufactured and what is the benefit? The cutting tips are diamond-ground carbide, which improves edge consistency and prolongs cutting life, resulting in more predictable machining and reduced frequency of tip changes. Which SKU should be ordered for this hook-style turning tool? Order SKU 4118660102NW for the Wilke hook-style turning tool with 12 x 12 mm cross-section and P25/P30 carbide tips. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm 25 x 25 External Threading Tool Carbide P25/P30 60° Right-Hand WN282 - Werner Wilke Zerspanungstechnik GmbH
Combining a carbide P25/P30 grade with a 60° tip and a rigid 25 x 25 mm cross-section delivers precise, repeatable external threads in production environments; request supply or consulting directly from Metav Werkzeuge for a dependable addition to the tooling kit. External thread turning tool 25 x 25 mm, carbide P25/P30, right-hand, 60° (Wilke) External thread turning tool 25 x 25 mm for precision external threading on lathes and CNC turning centres with a steel shank fitted with diamond-ground carbide inserts Carbide P25/P30 for extended tool life 25 x 25 mm cross-section for rigid set-up 60° tip for ISO metric threads Right-hand cutting for standard lathes High-precision threads through optimised carbide The External thread turning tool 25 x 25 mm uses carbide P25/P30, a grade optimised for a balance of toughness and wear resistance, which reduces flank wear during serial production. The 60° tip conforms to ISO metric threading geometry, enabling consistent profile accuracy and reducing rework. This technical combination supports higher first-pass yields and predictable tool-change intervals, promoting leaner machining cycles and measurable productivity gains. Rigid tool body for consistent repeatability A 25 x 25 mm cross-section and a 160 mm length provide a stiff mounting condition, lowering vibration and improving surface finish on the thread flank. The tool is supplied on a steel shank fitted with diamond-ground inserts, which ensures repeatable seat accuracy and minimal run-out when clamped in standard tool holders. Right-hand cutting orientation matches common lathe stock rotation, simplifying setup and reducing the need for alternative tooling. Seamless integration and reliable sourcing Designed to the WN282 designation, the tool integrates with existing turning tool stations and clamping systems without custom adapters. Supplied as a single unit per packaging, it is suitable for workshop replenishment or targeted replacement in production cells. For technical clarification or compatibility checks, Metav Werkzeuge acts as a precision partner, offering product knowledge and rapid fulfilment from its Emmerich supply hub. For specification guidance or to arrange delivery of the Wilke external thread turning tool, contact Metav Werkzeuge directly for tailored advice and prompt supply from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 4118650402NW Name: External thread turning tool 25 x 25 mm HM P25/P30 re. 60° Wilke Product type: External thread turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 160 mm Cross-section: 25 x 25 mm Tip angle: 60° Packaging unit: 1 Special features Material: carbide P25/P30 Cutting direction: right-hand Norm: WN282 Steel shank fitted with diamond-ground carbide inserts FAQ What thread form does the tool produce? The tool produces ISO metric thread profiles via its 60° tip geometry; the External thread turning tool 25 x 25 mm is configured for standard external threading. Which materials suit this turning tool? The Wilke carbide grades P25/P30 are optimised for general-purpose turning, particularly for steels and similar alloys where a balance of wear resistance and toughness is required. How is the tool supplied and mounted? The tool is supplied as a single unit (packaging unit 1) on a steel shank; mounting uses a standard toolholder compatible with the WN282 designation. Is the cutting direction compatible with my lathe? This version is right-hand cutting, matching conventional lathe spindle rotation and common fixture setups. What identifies this specific article? Reference the SKU 4118650402NW for ordering and technical queries related to this external thread turning tool. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm Internal Thread Turning Insert 12x12mm Carbide P25/P30 60° Right-Hand WN283 - Werner Wilke Zerspanungstechnik GmbH
High precision for internal threads is ensured by the combination of solid carbide P25/P30 construction and a 12 x 12 mm cross-section, while the 60° profile and right-hand cutting direction guarantee compatibility with standard metric internal threads; order the WN283 tool via Metav Werkzeuge or request technical advice from their consultants. Internal thread turning tool 12 x 12 mm, solid carbide P25/P30, 60° — Wilke The internal thread turning tool 12 x 12 mm from Werner Wilke is a compact carbide-tipped tool designed for accurate internal threading in limited bores on conventional lathes Solid carbide P25/P30 for durable edges 12 x 12 mm cross-section for tight bores 60° profile for standard metric threads Right-hand cutting for conventional lathes Robust carbide grade for predictable cutting performance The tool is built with solid carbide P25/P30, a specification that combines wear resistance with stable cutting properties to support repeatable results in serial production. The chosen carbide grade and the precise edge geometry provide consistent chip formation and reduce the need for frequent regrinding, which translates into quieter toolroom cycles and fewer unscheduled tool changes. Stability under load is a key technical advantage for workshop environments focused on reproducible thread quality. Compact geometry that reaches confined bores With a 12 x 12 mm cross-section and an overall length of 160 mm, the design offers a compromise between rigidity and accessibility for internal threading tasks. The compact section reduces vibration in narrow bores while the length provides the reach necessary for deeper thread profiles. For machinists working on components with limited internal space, the geometry supports controlled tool engagement and improved surface finish, helping to maintain dimensional accuracy even in small or awkwardly positioned bores. Standard 60° profile and right-hand cutting for compatibility The 60° thread angle aligns with common metric and ISO thread forms, ensuring the tool is suitable for producing standard internal threads in a wide range of components. The right-hand cutting direction corresponds to typical lathe spindle rotation, simplifying setup on conventional turning centres. Identified as WN283, the cutter’s profile and orientation minimise setup complexity and help maintain thread form integrity across batches. Solid construction and precision-mounted cutting plates The tool combines a substantial steel shank with diamond-ground carbide cutting plates mounted to the holder, providing sharp, repeatable cutting edges and reliable seat stability. Diamond grinding of the plates enhances edge definition and contributes to consistent tool life. The assembly is suitable for routine workshop maintenance and offers clear traceability through the WN283 designation and article numbering, which aids stock management and reordering in industrial supply chains. For specification checks, availability of the Wilke WN283 internal thread turning tool or tailored application advice, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 for prompt technical support and supply information Technical data Article number: 4118655102NW Name: Internal thread turning tool 12 x 12 mm, WN283 Product type: Internal thread turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 160 mm Cross-section: 12 x 12 mm Point angle: 60° Packaging unit: 5 pieces Special features Material: solid carbide P25/P30 Steel shank with diamond-ground carbide cutting plates Right-hand cutting direction WN283 designation FAQ What material is the tool made from? The Wilke internal thread turning tool is supplied with solid carbide P25/P30 plates mounted on a steel shank with diamond-ground cutting plates for defined edge geometry. Which thread profile is produced with this tool? The tool employs a 60° profile, suitable for standard metric internal threads and compatible with common ISO thread forms. Is the tool suitable for use in confined bores? Yes, the 12 x 12 mm cross-section combined with the 160 mm overall length provides access to compact internal bores while maintaining sufficient rigidity for accurate threading. How is the tool identified for reordering? This item is designated WN283 and listed under article number 4118655102NW, produced by Werner Wilke Zerspanungstechnik GmbH Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16x16mm Carbide Turning Tool Bent Left-Hand DIN 4972 (ISO 2) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a robust combination of carbide P25/P30 cutting plates, a bent profile for improved chip control and a rigid 16 x 16 mm shank to maintain stable turning operations; order directly via Metav Werkzeuge or consult our specialists for application advice. Turning tool DIN 4972 (ISO 2) – 16 x 16 mm, Carbide P25/P30, Left-hand, Bent (Wilke) The Turning tool DIN 4972 (ISO 2) is a left-hand, bent lathe tool designed for precise external turning and reliable chip guidance in industrial and workshop environments Carbide P25/P30 cutting insert Bent profile for improved chip control Cross-section 16 x 16 mm shank Left-hand, compliant with DIN 4972 (ISO 2) Faster, more consistent turning through optimised carbide geometry Equipped with carbide P25/P30, the tool balances wear resistance and toughness to support steady cutting performance under varied loads. The combination of a compact 16 x 16 mm shank and an overall length of 110 mm reduces unwanted flex and vibration, which directly improves dimensional consistency and surface finish on turned parts. For manufacturers seeking reproducible cycle times, the hardened cutting plates and precise geometry reduce rework and help streamline production planning. Improved chip control and stability for reliable finishes The bent profile is specifically shaped to influence chip flow and contact angles, helping to evacuate swarf cleanly and prevent build-up on the cutting edge. A steel shank fitted with diamond-ground carbide cutting plates provides a secure mounting for the insert and promotes thermal stability during continuous use. These features combine to lower the risk of chatter and to produce a smoother component face, which is particularly beneficial in batch production and precision repair work. Practical fit for workshop and machine tool setups Designed according to DIN 4972 (ISO 2) standards, the turning implement integrates easily into common tool posts and toolholders used in turning centres and conventional lathes. The left-hand cutting direction caters for turning operations where the tool approaches from the workpiece’s right-hand side. Its compact geometry and standardised interfaces make it suitable for both retrofit and new-tool setups, enabling faster tool changes and predictable machine set-up times. Simple maintenance, spare-part logistics and packaging Cutting plates are replaceable, allowing maintenance teams to restore cutting performance without replacing the entire holder. The unit is supplied in a pack of 5, facilitating stock control and minimising downtime for shops that rotate tools frequently. With a clear article reference and standard dimensions, procurement can be planned reliably and integrated into existing inventory systems to maintain continuous production flow. For tailored recommendations or to arrange procurement through Metav Werkzeuge, please contact our team with the SKU 4118605602NW for fast, expert assistance. Technical data Article number: 4118605602NW Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Turning tool Label: Drehmeißel DIN 4972ISO2 16x16mm HM P25/P30 li. geb. Wilke Packaging unit: 5 Facts Cross-section: 16 x 16 mm Overall length: 110 mm Special features Material: Carbide P25/P30 Bent profile Left-hand cutting direction Steel shank with diamond-ground carbide cutting plates Compliant with DIN 4972 (ISO 2) FAQ What materials is this turning tool intended for? The turning tool with carbide P25/P30 is designed for general external turning applications; selection of the correct insert grade and cutting data should be matched to the workpiece material for optimal results. How does the bent profile affect chip control? The bent profile alters the contact angle and helps direct chips away from the cutting zone, improving evacuation and reducing the likelihood of re-cutting or edge build-up during extended passes. Is the insert replaceable and how is the tool supplied? The tool is supplied as a holder fitted with diamond-ground carbide cutting plates and is delivered in a pack of 5; worn plates can be replaced to restore cutting performance. Which standard does the tool conform to and why is that important? Compliance with DIN 4972 (ISO 2) ensures compatibility with standard toolholders and predictable mounting geometry, simplifying integration into existing lathe setups. What does the left-hand cutting direction mean for application? Left-hand cutting indicates the tool is intended to cut when the workpiece rotation and tool feed require a left-handed approach; it is suited to operations where the tool engages the workpiece from the right-hand side. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16x16mm Internal Corner Turning Tool Carbide P25/P30, Right-Hand, DIN 4974 (ISO 9) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of cemented carbide P25/P30 inserts, a compact 16 x 16 mm cross-section and a 210 mm overall length for consistent internal corner turning; order the tool directly via Metav Werkzeuge or ask the consultants for application advice. Internal corner turning tool DIN 4974 (ISO 9) — 16 x 16 mm, carbide P25/P30 (Werner Wilke) The Internal corner turning tool DIN 4974 (ISO 9) 16 x 16 mm HM P25/P30 re. Wilke provides precise internal profiling for medium-duty lathe operations and is designed for bores from 27 mm Cemented carbide P25/P30 insert Cross-section 16 x 16 mm Right-hand cutting direction Suitable for bores from 27 mm Accurate internal profiling with standardised geometry The Internal corner turning tool DIN 4974 (ISO 9) combines standardised tool geometry with cemented carbide cutting tips to deliver repeatable internal corner radii in routine production. The P25/P30 grade offers a balance between toughness and wear resistance, making it suited to a broad range of turning tasks on common engineering steels. The tool conforms to DIN 4974 (ISO 9), which ensures compatibility with existing toolholders and fixtures and simplifies process planning for workshops working to industrial standards. Sturdy construction for stable cuts and predictable tool life A steel shank fitted with diamond-ground carbide inserts gives the assembly torsional stability and consistent cutting edges, reducing vibration and improving surface finish. The compact 16 x 16 mm cross-section and 210 mm overall length provide a balance of reach and rigidity, while the right-hand cutting orientation is appropriate for conventional turning setups. These characteristics help to reduce set-up adjustments and increase the proportion of first-pass acceptable parts, supporting efficient machining cycles and lower rework rates. Designed for workshop reliability and straightforward selection Intended for turning shops, maintenance departments and small-batch production, this internal profiling tool supports operations where standardised, rugged tooling is valued. The specification indicating a minimum bore diameter of 27 mm helps planners confirm suitability quickly without extensive calculations. The combination of standard dimensions and a recognised carbide grade simplifies spare tooling management and procurement, allowing a predictable stocking strategy that reduces downtime in busy workshops. For tailored advice on integrating this Werner Wilke internal corner turning tool into existing toolsets or to arrange rapid supply from Metav Werkzeuge in Emmerich, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4118615202NW Norm: DIN 4974 (ISO 9) Product type: Internal corner turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Packaging unit: 5 Facts Overall length: 210 mm Cross-section: 16 x 16 mm Smallest bore Ø: 27 mm Cutting direction: Right-hand Special features Material: Cemented carbide P25/P30 Steel shank with diamond-ground carbide inserts Standardised DIN 4974 (ISO 9) geometry Label: Inneneckdrehmeißel DIN 4974ISO9 16x16mm HM P25/30 re. Wilke SKU/UID: 4118615202NW FAQ What materials is this tool suitable for? The Internal corner turning tool DIN 4974 (ISO 9) with P25/P30 carbide is primarily specified for general engineering steels and similar materials where a combination of toughness and wear resistance is required. What is the minimum bore size for use with this internal tool? The tool requires a minimum bore diameter of 27 mm, as indicated in the technical specification, to provide sufficient clearance for safe and effective internal profiling. Which cutting direction does the tool use and what does that mean for set-up? This version has a right-hand cutting orientation; operators should set the lathe and toolholder accordingly so that chip formation and tool approach suit conventional right-hand turning operations. How does the carbide grade P25/P30 affect performance? The P25/P30 carbide grade delivers a compromise between resistance to abrasive wear and impact toughness, resulting in reliable tool life under typical workshop turning conditions when using the Internal corner turning tool DIN 4974 (ISO 9). How is the tool supplied and what is the packaging unit? The product is supplied in a packaging unit of 5, enabling straightforward replenishment of commonly used tooling items in small-batch or continuous production environments. Manufacturer: Werner Wilke Zerspanungstechnik GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16x16mm Internal Thread Turning Tool Carbide P25/P30 60° Right-Hand WN283 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, a compact 16 x 16 mm cross-section and a precise 60° profile for reliable internal threading; order directly via Metav Werkzeuge or consult the technical team for application support. Internal thread turning tool 16x16 mm, carbide P25/P30, right-hand, 60° — Wilke A Internal thread turning tool 16x16 mm P25/P30 engineered for precise internal thread cutting in turning operations, suitable for repetitive workshop and light industrial use Carbide P25/P30 inserts for high wear resistance 16 x 16 mm square cross-section 60° thread angle for standard internal threads Right-hand cutting direction for conventional turning Consistent performance from premium carbide grades The choice of carbide P25/P30 offers a balance between toughness and hardness that benefits continuous machining processes. This grade resists abrasive wear while maintaining edge stability during interrupted cuts, which reduces the frequency of insert changes and supports longer uninterrupted production runs. The result is a lower total cost of operation through fewer tool changes and less machine downtime. Precise 60° profile for repeatable thread geometry A defined 60° tip angle provides the correct flank geometry for standard internal threads, ensuring thread form accuracy and improved mating with external threads. The controlled profile reduces the need for additional finishing passes and minimises the risk of rework, which is particularly valuable for components requiring consistent thread tolerance and surface finish across batches. Rigid holder geometry for secure clamping and stability The 16 x 16 mm square section combined with a steel shank and diamond-ground carbide cutting plates (as supplied) gives a stable tool assembly that resists vibration under load. The robust design supports higher cutting parameters where appropriate and simplifies tool positioning in the holder, translating directly into reproducible thread starts and improved dimensional stability on turned parts. Practical suitability and operational benefits With a total length of 180 mm and a right-hand cutting direction, this tool integrates easily into standard lathe setups for conventional internal threading tasks. Supplied in pack sizes of five, the tools allow preparations for serial production while keeping spare inserts accessible. The configured tool suits workshops aiming for dependable, repeatable threading without complex retooling. Contact Metav Werkzeuge for tailored application advice and to secure the Wilke carbide P25/P30 internal thread turning tool via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 4118655152NW Standard: WN283 Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Total length: 180 mm Cross-section: 16 x 16 mm Tip angle: 60° Pack unit: 5 Special features Material: Carbide P25/P30 Right-hand cutting direction Steel shank with diamond-ground carbide cutting plates Execution: 60° profile FAQ Which materials are suitable for machining with this tool? The internal thread turning tool 16x16 mm P25/P30 is designed primarily for general steel applications and similar materials where carbide inserts of grade P25/P30 provide effective wear resistance. How does the 60° tip angle affect thread compatibility? A 60° tip angle corresponds to standard thread flank geometry, which ensures that threads produced with this tool match common metric and unified profiles when used with correct pitch and feed settings. Is the tool supplied ready-to-use in the holder configuration described? The tool arrives equipped with diamond-ground carbide cutting plates on a steel shank, allowing immediate mounting and use in compatible tool holders for internal threading operations. What advantages do carbide P25/P30 inserts provide over other grades? Carbide P25/P30 combines hardness and toughness suitable for repetitive turning tasks, extending tool life under typical workshop cutting conditions and reducing the need for frequent insert replacement. Can this tool be used for interrupted cuts or entry into previously machined bores? The robust shank and carbide inserts provide the stability needed for many interrupted cuts; however, machining parameters should be adjusted according to the specific workpiece material and bore condition. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16x16mm Internal Turning Tool Carbide P25/P30, Right-Handed, DIN 4973 (ISO 8) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the diamond-ground carbide inserts (P25/P30), the 16 x 16 mm robust shank and the right-hand cutting orientation for consistent internal turning in restricted bores; order directly via Metav Werkzeuge or consult our specialists for compatibility and delivery options. Internal turning tool DIN 4973 (ISO 8) — 16 x 16 mm, carbide P25/P30, right-hand (Wilke) The Internal turning tool DIN 4973 (ISO 8) is a right-hand internal turning tool designed for machining bores from 27 mm upwards, featuring a steel shank fitted with diamond-ground carbide (P25/P30) cutting plates for precise internal finishing Carbide cutting inserts P25/P30 16 x 16 mm robust cross-section Right-hand cutting orientation Minimum bore Ø 27 mm Consistent bore quality thanks to diamond-ground carbide The combination of P25/P30 carbide and diamond-ground cutting plates provides a stable cutting edge and reduced vibration, which leads to consistent surface finishes in internal turning operations. The carbide grades cited ensure wear resistance under typical finishing feeds; the diamond-ground geometry stabilises chip formation and reduces the need for frequent edge dressing. For production environments where repeatable bore quality matters, this cutting arrangement supports predictable cycle times and fewer reworks. Rigid geometry for stable internal machining A 16 x 16 mm cross-section and a 210 mm overall length deliver the stiffness required for internal operations while permitting access into moderate-depth bores. The square shank profile resists torsion and bending under load, reducing chatter and preserving tool life. Compliance with DIN 4973 (ISO 8) ensures compatibility with standard tool holders and indexable setups, simplifying integration into existing turning centres without bespoke adapters. Designed for restricted bores and right-hand turning With a minimum bore diameter of 27 mm and a right-hand cutting orientation, the tool is tailored to internal facing, profiling and light boring tasks where access is limited. The right-hand cut direction suits standard spindle rotation and common turning strategies, providing intuitive tool paths for operators. This configuration is particularly useful for engineering workshops tackling internal machining on medium-sized components where tool access and reliable chip evacuation are critical. Easy specification and workshop integration The tool’s steel shank, fitted with diamond-ground carbide plates, allows straightforward replacement of inserts and predictable performance across batches. As a DIN-conforming internal turning tool, it fits established holders and clamping systems, reducing setup time. For procurement and planning, the item is supplied in packaging units of five, enabling stock control for small to medium production runs while maintaining traceability through the SKU and standard reference. Contact Metav Werkzeuge for tailored advice on fitting the Wilke internal turning tool with P25/P30 carbide inserts and to confirm availability from our Emmerich warehouse Technical data Article number: 4118610202NW Standard: DIN 4973 (ISO 8) Product type: Internal turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Core specifications Overall length: 210 mm Cross-section: 16 x 16 mm Minimum bore diameter: 27 mm Packaging unit: 5 Materials & special features Carbide: P25/P30 Right-hand cutting orientation Steel shank with diamond-ground carbide cutting plates FAQ What is the minimum bore diameter for this internal turning tool? The tool requires a minimum bore diameter of 27 mm, so internal operations below this diameter are not recommended. Which carbide grades are fitted to the cutting plates? The inserts are P25/P30 carbide, diamond-ground for stable cutting edges and improved surface finish in internal turning. Is this tool compatible with standard DIN holders? Yes, the tool conforms to DIN 4973 (ISO 8) and is designed to fit standard compatible holders and clamping systems. What is the cross-section and overall length of the shank? The shank measures 16 x 16 mm in cross-section with an overall length of 210 mm, offering a balance of stiffness and reach. Is the cutting orientation left- or right-hand? This internal turning tool features a right-hand cutting orientation, suitable for conventional spindle rotation and turning strategies. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16x16mm Side Turning Tool Carbide P25/P30 Offset Left DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of proven carbide performance and a DIN‑compliant stepped shank for stable clamping and repeatable results; the left‑hand cut and 110 mm overall length make this tool suitable for reverse turning and deeper operations. Order the part directly via Metav Werkzeuge or contact our consultants for application advice. Side‑turning tool DIN 4980 (ISO 6) 16 x 16 mm — carbide P25/P30, left‑hand (Werner Wilke) A side‑turning tool DIN 4980 (ISO 6) 16 x 16 mm designed for reliable external profiling and facing on lathes, featuring a stepped shank and diamond‑ground carbide cutting plates suited to industrial turning tasks Stepped shank, DIN 4980 (ISO 6) compatible Cross‑section 16 x 16 mm for stable clamping Left‑hand cutting direction for reverse machining 110 mm overall length for deep operations Consistent machining quality for production environments The Side‑turning tool DIN 4980 (ISO 6) 16 x 16 mm delivers consistent cut geometry thanks to its diamond‑ground carbide cutting plates in P25/P30 grade, which ensure high wear resistance and edge stability during repeated cycles. The stepped shank design increases clamping rigidity, reducing vibration and improving surface finish; DIN‑compliant shank dimensions also enable quick toolholder interchangeability across standard toolposts. For production lines where repeatability matters, this combination of precision and standard conformity reduces scrap rates and set‑up time. Longer service life and predictable maintenance intervals Fitted with carbide P25/P30, the turning tool is optimised for a balance between toughness and hardness, extending tool life on general steel turning operations. The material choice supports stable cutting in continuous use, which translates to fewer interruptions for tool changes and a lower total cost of ownership over time. The left‑hand orientation suits reverse or internal approach cuts, while the 16 x 16 mm cross‑section contributes to secure clamping and reduced deflection under load, helping maintain dimensional tolerances across batches. Straightforward compatibility and practical handling Compliance with DIN 4980 (ISO 6) offers clear mechanical compatibility with standard toolholders, simplifying procurement and stocking decisions. The stepped steel shank, equipped with carbide cutting plates, is easy to mount and index where applicable, and the 110 mm overall length provides extra reach for recessed or deeper turning tasks without compromising stability. For workshops transitioning between jobs, the standardised interface and robust carbide tips make process planning more predictable and reduce set‑up complexity. For ordering or technical advice on the carbide performance and compatibility of this side‑turning tool, contact Metav Werkzeuge for specialist guidance and procurement support Technical Data Article number: 4118640602NW Product type: Side‑turning tool Label: Seitendrehmeißel DIN 4980ISO6 16x16mm HM P25/P30 li. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 110 mm Cross‑section: 16 x 16 mm Packaging unit: 5 Special features Material: carbide P25/P30 Stepped shank (abgesetzt) DIN 4980 (ISO 6) compatible Steel shank fitted with diamond‑ground carbide cutting plates Left‑hand cutting direction FAQ What materials is this turning tool suited for? The turning tool with carbide P25/P30 is suitable primarily for general steel machining; the carbide grade balances toughness and hardness for reliable performance in common turning applications. Is the shank compatible with standard toolholders? Yes, the stepped shank conforms to DIN 4980 (ISO 6), ensuring mechanical compatibility with standard holders that accept 16 x 16 mm shanks. What is the overall length and how does it affect reach? The overall length is 110 mm, offering increased reach for deeper or recessed turning tasks while maintaining clamping stability. Can this tool be used for reverse or left‑hand cuts? The tool is specified with a left‑hand cutting direction, making it suitable for reverse‑direction machining and specific facing or profiling operations. What is the article number for ordering and reference? The SKU for ordering and reference is 4118640602NW; include this when enquiring to ensure the correct side‑turning tool and configuration are supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com