180mm 12 x 12mm Internal Turning Tool Carbide P25/P30 Right-Handed, DIN 4973 (ISO 8) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the blend of carbide P25/P30 cutting plates, compact 12 x 12 mm cross-section and a 180 mm overall length for reliable internal turning in restricted bores; robust construction reduces tool changes and supports consistent surface quality. Order the (Internal turning tool DIN 4973 (ISO 8) 12 x 12 mm, Carbide P25/P30, right-hand) directly via (Metav Werkzeuge) or ask our consultants if needed. Internal turning tool DIN 4973 (ISO 8) – 12 x 12 mm, Carbide P25/P30 (right-hand) — Werner Wilke Internal turning tool DIN 4973 (ISO 8) – 12 x 12 mm, Carbide P25/P30 (right-hand) — Werner Wilke is a purpose-built tool for precision internal turning in bores from 21 mm, featuring diamond-ground carbide cutting plates on a steel shank for stable performance Carbide P25/P30 cutting plates Compliant with DIN 4973 (ISO 8) Steel shank with diamond-ground plates Minimum bore Ø 21 mm Consistent cutting performance for internal bores The compact design with 12 x 12 mm cross-section and fitted carbide P25/P30 plates delivers predictable wear characteristics and reliable chip control in confined internal turning tasks. The compliance with DIN 4973 (ISO 8) signals standardised geometry and clamping interfaces, which simplifies toolholder selection and streamlines setup in production environments. Translating grade codes: P25/P30 denotes a fine-grained carbide composition optimised for general to fine finishing applications, offering a balance between toughness and wear resistance that supports longer intervals between tool changes. Stable construction for precise finishes and reduced vibration A steel shank fitted with diamond-ground carbide cutting plates ensures rigid seating and accurate cutting edge positioning, which benefits surface finish and dimensional repeatability. The 180 mm overall length provides sufficient reach for many internal operations while maintaining stiffness; the right-hand cutting direction supports standard lathe rotations and tool paths. This combination reduces the risk of chatter, which otherwise affects cycle times and rework rates, thereby contributing to a more efficient machining flow. Practical data for planning and integration The tool is specified for internal turning in bores from 21 mm and is supplied in a packaging unit of 5. Its compact profile and standardised norm make it straightforward to integrate into existing tool stations and adaptors. Where tighter tolerances or different inserts are required, the standardised mounting and the diamond-ground plate finish allow predictable regrinding or replacement procedures, keeping downtime to a minimum and supporting continuity in serial production. For tailored advice on integrating this internal turning tool with specific holders or machines, contact Metav Werkzeuge for technical guidance and procurement assistance — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: 4118610152NW Product type: Internal turning tool Norm: DIN 4973 (ISO 8) Material: Carbide P25/P30 Facts Overall length: 180 mm Cross-section: 12 x 12 mm Minimum bore diameter: 21 mm Packaging unit: 5 pcs Special features Steel shank with diamond-ground carbide cutting plates fitted Right-hand cutting direction Compact profile optimised for internal turning FAQ What is the minimum bore diameter for this internal turning tool? The minimum bore diameter for the Internal turning tool DIN 4973 (ISO 8) 12 x 12 mm, Carbide P25/P30 (right-hand) is 21 mm, which defines the smallest internal cavity where the tool can be used effectively. Which material are the cutting plates made from? The cutting plates are carbide P25/P30, a fine-grained carbide grade chosen for its balance of wear resistance and toughness suitable for internal finishing operations. Does the tool conform to an industry standard? Yes, the tool conforms to DIN 4973 (ISO 8), ensuring standardised dimensions and compatibility with corresponding toolholders. What are the key dimensional specifications of the tool? Key dimensions include a 12 x 12 mm cross-section and an overall length of 180 mm as listed for SKU 4118610152NW. How is the tool supplied and what is the packaging unit? The Internal turning tool is supplied in a packaging unit of 5 pieces, making it suitable for batch machine tooling or stocking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
180mm Hakendrehmeissel 16x16mm Solid Carbide P25/P30 5mm Cut Width, Right-Hand - Werner Wilke Zerspanungstechnik GmbH
Benefit from a combination of P25/P30 carbide cutting heads, a rigid 16 x 16 mm shank and a 5 mm plunge width for reliable, repeatable turning results; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Hook turning tool 16 x 16 mm HM P25/P30 (right‑hand) — Werner Wilke precision turning chisel with carbide tips Hook turning tool 16 x 16 mm HM P25/P30 (right‑hand) is a right‑hand turning chisel designed for precision lathe operations where stable clamping and controlled plunge cutting are required. Solid carbide P25/P30 cutting heads Cross-section 16 x 16 mm for stable clamping 5 mm plunge width for precise grooving Right-hand cutting direction for lathe turning Consistent metal removal for production environments The tool delivers consistent cutting performance by combining a square 16 x 16 mm shank with hardened carbide heads in grades P25/P30, ensuring dimensional stability during continuous turning work. The 5 mm plunge width allows controlled material access for grooving and profiling operations, reducing the need for repeated passes. This configuration supports process reliability and helps maintain component tolerances in small-batch and serial production. Durable carbide construction reduces downtime Fitted with carbide cutting plates, the design prioritises wear resistance and predictable tool life. The specification P25/P30 refers to cemented carbide grades selected for a balance of toughness and hardness, making the tool suited to typical workshop turning tasks where edge retention and impact resistance matter. Diamond-ground faces on the inserts promote stable cutting edges and help achieve consistent surface finishes without frequent regrinding. Secure mounting and machine compatibility The square shank geometry provides secure seating in standard 16 mm tool holders, improving rigidity and vibration control during turning. With an overall length of 180 mm and a right‑hand cutting direction, the tool is compatible with conventional lathe setups that accept square shanks and right‑hand tools. The combination of shank stability and carbide tip design supports accurate, repeatable results in machining sequences. Practical handling and maintenance guidance Constructed as a steel shank equipped with diamond-ground carbide cutting plates, the tool is built for straightforward handling and inspection. Regular visual checks of the cutting edge and timely replacement of worn inserts extend service life and preserve part quality. Where a fine surface or tight tolerance is required, the carbide tips deliver consistent performance until replacement is necessary, simplifying maintenance planning for workshop teams. For reliable carbide performance from Werner Wilke and purchase assistance, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for personalised advice and order support. Technical data Article number: 4118660152NW Designation: WN263 Label: Hakendrehmeißel 16x16mm HM P25/P30 re. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Core technical data Overall length: 180 mm Cross-section: 16 x 16 mm Plunge width: 5 mm Packaging unit: 5 Special features Material: Carbide P25/P30 Cutting direction: right‑hand Shank: steel shank with diamond-ground carbide cutting plates Standard/nominal: WN263 FAQ What cutting direction does this turning tool use? The tool features a right‑hand cutting direction; the Hook turning tool 16 x 16 mm HM P25/P30 (right‑hand) from Werner Wilke is therefore intended for right‑hand lathe operations. Which dimensions define the shank and reach? The tool has a square shank of 16 x 16 mm and an overall length of 180 mm, as stated for SKU 4118660152NW. What material are the cutting heads made from? The cutting plates are manufactured from P25/P30 cemented carbide, providing a balance between toughness and hardness for stable cutting performance. How wide is the plunge or grooving capacity? The tool offers a 5 mm plunge width, which supports precise grooving and controlled material removal in turning tasks. What construction details support durability? The device is a steel shank with diamond-ground carbide cutting plates, a combination that promotes edge stability and consistent wear characteristics for routine workshop use. Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20 x 12mm Parting Tool Carbide P25/P30 5mm Cut Width, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, a 5 mm parting width and a rigid 20 x 12 mm shank for controlled, repeatable parting operations; order directly via Metav Werkzeuge or ask the technical consultants for application advice. Wilke Stechdrehmeißel (Parting Tool) 20 x 12 mm — HM P25/P30, left-hand The Stechdrehmeißel (parting tool) is designed for left-hand parting and grooving in lathe turning, featuring a robust 20 x 12 mm shank and diamond-ground carbide cutting plates for stable performance. Carbide grades P25/P30 for durability 5 mm parting width for precise cuts 20 x 12 mm shank, 125 mm overall length Left-hand cutting, DIN 4981 (ISO 7) compatibility Durable carbide for consistent cutting performance The tool uses Hartmetall P25/P30 inserts that combine wear resistance with a balanced toughness, reducing the frequency of insert changes and downtime. Diamond-ground cutting faces ensure a consistent cutting edge geometry, which improves surface finish and reduces micro-chipping during high-precision parting work. This results in fewer interruptions to the machining cycle and a measurable uplift in process stability when compared with generic-grade inserts. Compact, rigid design for accurate parting and groove control A 20 x 12 mm shank cross-section and an overall length of 125 mm provide the rigidity required for narrow 5 mm parting operations. The compact profile reduces deflection under load and supports accurate depth control, so operators benefit from cleaner cut-off points and reduced secondary finishing. Conformance to DIN 4981 (ISO 7) simplifies integration with compatible tool holders, ensuring straightforward mounting and repeatable set-up. Left-hand orientation and standard compatibility for flexible shop use The left-hand cutting orientation is suited to applications where tool approach and spindle rotation necessitate a leftward cutting direction; this is specified in the product designation to avoid setup errors. The parting blade is equipped on a steel shank with diamond-ground carbide plates, a configuration that balances economy with service life. For shops standardising tooling, the compliance with recognised norms streamlines inventory choices and reduces the need for bespoke holders. Practical handling and predictable maintenance Thanks to the replaceable carbide plates, maintenance focuses on quick insert swaps rather than full tool replacement, cutting service time and inventory waste. The tool’s geometry supports controlled chip formation at the specified 5 mm cutting width, reducing the chance of chip entanglement during parting. For complex or critical applications, Metav’s technical team can provide guidance on optimised cutting parameters and compatible tool holders to preserve tool life and part quality. Request tailored advice from Metav Werkzeuge for optimal deployment of the Wilke left-hand parting tool — Metav’s specialists can recommend holders, cutting parameters and delivery options from Emmerich Technical data Article number: 4118645602NW Label: Stechdrehmeißel DIN 4981ISO7 20x12mm HM P25/P30 li. Wilke Type: Stechdrehmeißel Manufacturer: Werner Wilke Zerspanungstechnik GmbH Standard: DIN 4981 (ISO 7) Core technical data Overall length: 125 mm Cross-section: 20 x 12 mm Parting width: 5 mm Packing unit: 5 Design & special features Material: Hartmetall P25/P30 Left-hand cutting direction Steel shank with diamond-ground carbide cutting plates Designed for parting and grooving in turning operations FAQ What does left-hand cutting mean for setup? Left-hand cutting indicates the tool is designed to cut when fed from right to left relative to the workpiece; the Wilke parting tool must be mounted accordingly to match spindle rotation and feed direction. How wide is the cutting slot produced by this tool? The tool provides a 5 mm parting width as specified; this dimension refers to the effective cut width produced by the carbide cutting plates. Which standard ensures holder compatibility? Compatibility is assured by DIN 4981 (ISO 7), which defines the tool-shank and holder interfaces relevant to this parting tool. What are the benefits of P25/P30 carbide grades? P25/P30 carbide grades offer a balance of wear resistance and toughness, delivering reliable edge life for interrupted cuts and the demands of parting operations. How is the tool maintained when inserts wear? The diamond-ground carbide plates are replaceable; worn plates are exchanged rather than replacing the entire shank, reducing maintenance time and material waste. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20 x 20mm Bent Turning Tool Carbide P25/P30 Left-Hand DIN 4972 (ISO 2) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of P25/P30 carbide cutting plates, a bent left‑hand geometry, and standardised DIN 4972 (ISO 2) dimensions for consistent turning performance; order the tool directly via Metav Werkzeuge or contact their consultants for application guidance. Wilke bent turning tool DIN 4972 (ISO 2) — 20 x 20 mm, carbide P25/P30, left‑hand Wilke bent turning tool DIN 4972 (ISO 2) 20 x 20 mm P25/P30 is a left‑hand, bent lathe tool intended for demanding turning tasks where access and reliable chip control are required Carbide P25/P30 for high wear resistance Bent shank for improved chip evacuation DIN 4972 (ISO 2) standardised geometry Left‑hand cutting orientation for specialised operations Robust carbide composition for longer service life The tool is equipped with P25/P30 carbide, a grade chosen for a balance of toughness and wear resistance, which supports extended tool life during continuous turning cycles. Diamond‑ground cutting plates reduce friction at the cutting edge and contribute to a consistent surface finish, while the steel shank provides the necessary rigidity for repeatable results. These material choices result in fewer tool changes and less downtime, improving throughput in production environments. Geometry and form for precise left‑hand turning Built to DIN 4972 (ISO 2) dimensions with a 20 x 20 mm cross‑section and a bent profile, the design offers improved access to shoulders and internal contours compared with straight tools. The left‑hand cutting orientation enables operations where the feed and spindle rotation require a left‑hand tool, helping to maintain correct cutting directions and secure chip flow. The overall length of 125 mm balances reach and stiffness, supporting stable cutting at moderate depths of cut. Practical workshop integration and predictable handling This indexable style solution arrives with diamond‑ground carbide plates mounted on a steel shank, ensuring repeatable seating and alignment in standard tool holders compatible with DIN 4972 tooling. The combination of a 20 x 20 mm shank and standardised geometry simplifies tooling setup and replacement cycles, reducing set‑up time. Clear specification of the cutting direction and form supports process planning and inventory management for metalworking shops seeking consistent, industrial‑grade turning tools. Contact Metav Werkzeuge for tailored advice on selecting the correct Wilke bent turning tool and to discuss compatible tool holders or application parameters; Metav Werkzeuge provides expert consultation and shipment from Emmerich to the European workshop. Technical data Article number: 4118605652NW Label: Drehmeißel DIN 4972ISO2 20x20mm HM P25/P30 li. geb. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Turning tool Norm: DIN 4972 (ISO 2) Facts Cross‑section: 20 x 20 mm Overall length: 125 mm Cutting direction: left Material: Carbide P25/P30 Packing unit: 5 Special features Bent profile Steel shank with diamond‑ground carbide cutting plates Standardised geometry for compatible tool holders FAQ What materials is this turning tool best suited for? The Wilke bent turning tool with P25/P30 carbide is designed for general steel turning and applications where a combination of wear resistance and toughness is required; actual performance depends on cutting data and workpiece material. Can the carbide plates be reconditioned or indexed? The tool is supplied with diamond‑ground carbide plates mounted on a steel shank; depending on workshop practices, the plates can be replaced to restore cutting geometry and performance. Is the geometry compatible with common tool holders? Yes, the DIN 4972 (ISO 2) conformity and 20 x 20 mm cross‑section ensure compatibility with holders designed for standardised turning tool inserts. What advantages does the bent, left‑hand form provide? The bent shank improves access to shoulders and tight contours, while the left‑hand cutting orientation is required where spindle rotation and feed direction mandate a left‑hand tool for correct machining. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20 x 20mm Turning Tool Carbide P25/P30 Straight DIN 4971 (ISO 1), Right-Hand - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 grade, a rigid 20 x 20 mm cross-section and compatibility with DIN 4971 (ISO 1) for reliable, repeatable turning operations; order directly via Metav Werkzeuge or consult our advisers for application support. Wilke turning tool DIN 4971 (ISO 1) – 20 x 20 mm, carbide P25/P30, right‑hand, straight The Wilke turning tool is a straight, right‑hand lathe toolholder designed for general turning tasks in workshop and industrial environments, compatible with DIN 4971 (ISO 1) tool clamping systems. Carbide grade P25/P30 for durability and performance 20 x 20 mm cross-section for stable clamping Right‑hand straight design for conventional turning Fitted with diamond‑ground carbide cutting plates High stability and standardised compatibility for secure clamping A compact, standardised design ensures reliable clamping in holders compliant with DIN 4971 (ISO 1). The 20 x 20 mm cross-section combines stiffness with compactness, reducing chatter and improving surface finish when paired with suitable tool posts. This configuration benefits setup speed and machine uptime by fitting common lathe toolholders without additional adapters, supporting efficient changeovers and consistent results. Carbide cutting performance tailored for general turning Equipped with Hartmetall P25/P30 carbide cutting plates, the assembly offers a balance between toughness and wear resistance suitable for a wide range of steels and general engineering materials. The diamond‑ground finish on the inserts enhances edge durability and delivers a sharper initial cutting geometry, which translates into steadier cutting forces and longer intervals between dressing or replacement. The specification is aimed at operators seeking dependable tool life under typical workshop feeds and speeds. Practical geometry for everyday machining tasks The straight, right‑hand configuration provides a familiar geometry for conventional turning operations. With an overall length of 125 mm, the toolholder gives adequate reach while maintaining rigidity close to the clamped shank. This geometry supports repeatable results in facing, light profiling and external turning where a robust shank and precise insert seating are essential for dimensional accuracy and surface quality. Ready supply and workshop suitability Supplied as a pack of five, the product suits small series production or stocking for maintenance cycles. The steel shank fitted with carbide plates arrives ready for installation into standard DIN‑compliant holders, reducing setup time. Metav’s procurement and logistics from Emmerich ensure transparent order processing and reliable delivery for workshops and small industrial users looking to consolidate suppliers and simplify inventory management. For precision turning with carbide performance, contact Metav Werkzeuge for advice and fast supply from Emmerich — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: 4118601202NW Label: Drehmeißel DIN 4971ISO1 20x20mm HM P25/P30 re. ger. Wilke Product type: Turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH UID: 4118601202NW Facts Cross-section: 20 x 20 mm Overall length: 125 mm Packaging unit: 5 Special features Material: Hartmetall P25/P30 Form: straight Standard: DIN 4971 (ISO 1) Cutting direction: right‑hand Configuration: steel shank fitted with diamond‑ground carbide cutting plates FAQ What materials is the tool suitable for? The Wilke turning tool is specified with carbide P25/P30 cutting plates, making it suitable for general engineering materials such as common steels; compatibility with harder or exotic alloys should be evaluated against cutting parameters and insert wear. How is the tool mounted in a lathe? The tool is made to DIN 4971 (ISO 1) dimensions and is clamped into standard DIN‑compliant tool holders; correct seating and positive clamping ensure repeatable alignment and rigidity. Does the tool come ready to use? Yes, the assembly is supplied with diamond‑ground carbide cutting plates already fitted to the steel shank, allowing immediate installation and use in compatible holders. What advantages do diamond‑ground inserts offer? Diamond‑ground inserts provide a precise cutting edge and improved initial sharpness, resulting in steadier cutting forces and better surface finish for typical workshop turning tasks. Is this tool suitable for high‑volume production? The robust 20 x 20 mm shank and P25/P30 carbide make it a reliable choice for sustained workshop production; for very high volumes or specialised materials, tool selection should be reviewed for optimal lifecycle economics. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20 x 20mm Turning Tool Carbide P25/P30 Straight Left-Hand DIN 4971 (ISO 1) - Werner Wilke Zerspanungstechnik GmbH
Benefit from the combination of P25/P30 carbide construction, a compact 20 x 20 mm cross-section and a straight design for reliable left-hand turning in production environments; order this turning tool directly via Metav Werkzeuge or consult our specialists for application advice. Turning tool DIN 4971 (ISO 1) 20 x 20 mm – Carbide P25/P30, left-hand, straight (Wilke) Turning tool DIN 4971 (ISO 1) 20 x 20 mm – Carbide P25/P30, left-hand, straight (Wilke) is a straight, carbide-tipped turning tool designed for standardised workshop turning tasks where repeatable geometry and tool life are priorities Solid carbide P25/P30 cutting tip 20 x 20 mm square cross-section Conforms to DIN 4971 (ISO 1) Straight shank, left-hand cutting Precision and durability for consistent turning results This carbide-tipped turning tool and its P25/P30 grade inserts deliver a robust balance of hardness and toughness, making it suitable for repetitive turning operations. The 20 x 20 mm cross-section provides stable clamping and reduced vibration, which preserves the cutting edge and improves surface finish. Conformity with DIN 4971 (ISO 1) ensures interchangeability with standard toolholders and predictable axial positioning, supporting consistent process control on the shop floor. The result is fewer tool changes and steadier component tolerances. Seamless integration with standard toolholders and workflows Engineered as a straight shank tool with a 125 mm overall length, this tool is straightforward to mount in existing tool posts and turrets that accept ISO 1 turning tools. The adherence to established norms simplifies set-up and inventory management across multiple machines. A steel shank fitted with diamond-ground carbide cutting plates reduces micro-chatter and assists repeatable clamping, so setup times are reduced and production throughput is improved without bespoke adapters or modifications. Practical handling and material versatility Although optimised for general-purpose turning, the carbide composition and insert geometry make the tool suitable for a range of steel machining tasks in day-to-day workshop use. The left-hand cutting direction is clearly indicated, avoiding mix-ups at the workbench and helping plan tool rotation and chip evacuation. Clear item identification and a compact square profile also aid storage and rapid retrieval during job changes, supporting lean production practices and minimising downtime. Why this tool fits a professional workshop For procurement and shop-floor managers looking for reliable, standardised tooling, this product combines the advantages of a hardened cutting tip with the practical benefits of a norm-compliant shank. The diamond-ground carbide plates give consistent edge preparation, which improves surface quality on machined parts and extends service intervals. Where predictability and compatibility with established machine tooling systems matter, this turning tool bridges technical performance with operational simplicity. Contact Metav Werkzeuge for tailored application advice and to confirm availability of the Wilke turning tool; our consultants can advise on compatibility and delivery directly from Emmerich Technical Data Article number: 4118601652NW Label: Drehmeißel DIN 4971ISO1 20x20mm HM P25/P30 li. ger. Wilke Product type: Turning tool Material: Hartmetall P25/P30 Facts Overall length: 125 mm Cross-section: 20 x 20 mm Cutting direction: Left-hand Packing unit: 5 pieces Special features Conforms to DIN 4971 (ISO 1) Straight execution Steel shank with diamond-ground carbide cutting plates Carbide grade P25/P30 FAQ What materials is this turning tool suitable for? The Wilke turning tool fitted with P25/P30 carbide inserts is primarily suited to general steel machining; its carbide composition provides wear resistance appropriate for many workshop steel applications. Is the tool compatible with standard ISO 1 toolholders? Yes, the tool is manufactured to DIN 4971 (ISO 1) dimensions and is intended for direct use in toolholders that accept ISO 1 turning tools. What does left-hand cutting mean for machine setup? Left-hand cutting indicates the orientation of the cutting edge relative to spindle rotation; the tool should be mounted and the programme set accordingly to ensure correct cutting direction. How is the tool supplied and identified? The item is supplied in a packing unit of 5 pieces and is listed under SKU 4118601652NW for straightforward inventory tracking. Can the carbide inserts be reworked or re-sharpened? The diamond-ground carbide cutting plates are prepared for service life and precision; reconditioning depends on workshop practice, but replacement of inserts is the standard approach for maintaining cutting geometry. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20x12mm Corner Turning Tool Carbide P25/P30 Offset Right DIN 4978 (ISO 3) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a rugged combination of carbide P25/P30 cutting edges, a stepped shank for improved accessibility and a DIN‑compliant geometry for repeatable turning performance; order this tool directly via Metav Werkzeuge or consult our specialists for application advice. Corner turning tool DIN 4978 (ISO 3) 20 x 12 mm, carbide P25/P30, right‑hand (Wilke) The Corner turning tool DIN 4978 (ISO 3) 20 x 12 mm is a stepped, right‑hand external turning holder supplied with diamond‑ground carbide inserts for precise, stable metalworking operations. Carbide P25/P30 grade for wear resistance Stepped shank for better access Right‑hand cutting orientation Conforms to DIN 4978 (ISO 3) Consistent cutting performance from a proven carbide grade The tool is equipped with Carbide P25/P30 inserts, a specification that balances hardness and toughness for reliable edge life in general turning applications. The DIN 4978 (ISO 3) geometry ensures a standardised rake and clearance configuration, which simplifies setup and helps to reproduce cutting conditions across different machines. These attributes result in consistent chip formation and extended service intervals compared with unspecified, non‑graded inserts. For production environments where predictable tool life and fewer interruptions improve throughput, this specification brings measurable operational stability. Improved accessibility and rigidity with the stepped shank A stepped shank design gives greater clearance to shoulder areas and hard‑to‑reach contours while maintaining torsional stability. The holder’s 20 x 12 mm cross‑section and 125 mm overall length provide a compact footprint with the stiffness required for stable external turning. Because the shank is a steel shank fitted with diamond‑ground inserts, the interface between holder and insert is precision finished for repeatable seating and minimal runout. The result is reduced vibration and improved surface finish on turned components, especially when working on short to medium overhangs. Straightforward integration into workshop tooling systems The turned holder is delivered ready for installation and matches standard tool posts that accept DIN‑compliant profiles. The combination of a hardened, finished holder and diamond‑ground carbide cutting edges simplifies clamping and repeatable indexing, which shortens tool change and setup times. Maintenance is likewise uncomplicated: worn carbide inserts can be replaced without modifying the holder, limiting downtime and keeping toolstock management efficient. For operations seeking dependable mechanical performance in everyday turning tasks, this insert‑equipped holder provides a pragmatic balance of durability and serviceability. For tailored application guidance or to secure inventory from Metav Werkzeuge, contact Metav Werkzeuge directly — their specialists can advise on compatibility with existing tool posts and recommend suitable inserts for specific machining tasks Technical data Article number: 4118635102NW Product: Corner turning tool Brand: Werner Wilke Zerspanungstechnik GmbH Dimensions & performance Length: 125 mm Cross‑section: 20 x 12 mm Cutting direction: right‑hand Standard: DIN 4978 (ISO 3) Package quantity: 5 Design & special features Material: Carbide P25/P30 Shank: steel shank fitted with diamond‑ground carbide inserts Shank style: stepped (abgesetzt) Label: Eckdrehmeißel DIN 4978ISO3 20x12mm HM P25/P30 re. Wilke FAQ What materials suit the Corner turning tool DIN 4978 (ISO 3) 20 x 12 mm? The Corner turning tool DIN 4978 (ISO 3) 20 x 12 mm is furnished with Carbide P25/P30 inserts, providing a good compromise of hardness and toughness for a wide range of general turning tasks encountered in workshops. How is the insert seating achieved on this Wilke turning holder? The Wilke holder features a steel shank with diamond‑ground inserts, ensuring precise seating and repeatable clamping for consistent cutting geometry. Can this tool be used in standard tool posts? Yes, the turning holder follows DIN 4978 (ISO 3) geometry so it integrates with tool posts designed for DIN‑compliant turning profiles. What is the package quantity and SKU for ordering? The item ships in a package quantity of 5 and is listed under SKU 4118635102NW for procurement and inventory tracking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20x20mm Internal Corner Turning Tool Carbide P25/P30, 250mm, Right-Hand, DIN 4974 (ISO 9) - Werner Wilke Zerspanungstechnik GmbH
High-precision internal corner turning with a 20 x 20 mm cross-section and a carbide P25/P30 cutting edge delivers consistent corner radii and long service life; combine durability, straightforward insert maintenance and compatibility with bores from 34 mm for reliable machining cycles. Order the internal corner turning tool directly via Metav Werkzeuge or ask our consultants for application advice. Internal corner turning tool Wilke (DIN 4974 / ISO 9) – 20 x 20 mm, carbide P25/P30 The internal corner turning tool Wilke is designed for precise internal radius machining, featuring a steel shank fitted with diamond-ground carbide inserts for use in bores from 34 mm upward. Steel shank with carbide inserts Carbide grade P25/P30 for long life Suitable for bores from 34 mm Precision and productivity in confined bores The tool combines a rigid 20 x 20 mm cross-section with an overall length of 250 mm, offering stable turning performance in internal applications. The carbide P25/P30 cutting edges provide a balance between toughness and wear resistance, which reduces microchipping and maintains dimensional accuracy over longer production runs. Conforming to DIN 4974 (ISO 9) ensures interchangeability with established holders and setups, simplifying tool replacement and machine setup times. These characteristics translate into fewer interruptions and a measurable productivity gain on the turning centre. Versatile material capability and predictable results Equipped with diamond-ground inserts on a steel shank, the turning holder is suitable for a wide range of internal finishing and profiling tasks. The right-hand cutting direction is optimised for conventional internal turning operations. The tool’s geometry and carbide grade make it appropriate for steels and typical engineering alloys where consistent corner radii and surface quality are required. By specifying this turning tool, machinists benefit from predictable tool life and repeatable part quality, reducing rework and securing process stability in small-diameter bores. Reliability, serviceability and procurement confidence Maintenance is straightforward: replace the diamond-ground carbide inserts to restore cutting performance without changing the whole holder, which keeps downtime and operating costs low. Supplied in a packaging unit of 5, this tool is suitable for workshops that require quick replenishment. Sourced from established manufacturing practice and kept in stock via Metav’s European distribution, the turning tool supports steady supply chains and fast dispatch. For buyers seeking a dependable internal turning solution, this tool offers the technical conformity and supply reliability needed for continuous production. For precision internal turning applications, specify the Wilke internal corner turning tool with carbide P25/P30 and contact Metav Werkzeuge for tailored advice and supply: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4118615252NW Label: Internal corner turning tool DIN 4974 (ISO 9) 20 x 20 mm carbide P25/P30 right-hand (Wilke) Product type: Internal corner turning tool Standard: DIN 4974 (ISO 9) Facts Overall length: 250 mm Cross-section: 20 x 20 mm Smallest bore diameter: 34 mm Cutting direction: right-hand Special features Material: carbide P25/P30 Steel shank with diamond-ground carbide inserts Packaging unit: 5 FAQ What is the minimum bore diameter for use with this tool? The tool requires a minimum bore diameter of 34 mm, as specified for the internal corner turning tool (SKU 4118615252NW), ensuring adequate clearance for the holder and inserts. Which carbide grade is fitted on the inserts? The turning tool uses carbide grade P25/P30, chosen for a compromise of toughness and wear resistance suited to internal finishing on typical engineering steels. Is the holder right- or left-handed? This version is a right-hand internal corner turning tool, designed for conventional internal turning operations on lathes and turning centres. Can the cutting inserts be replaced separately? Yes, the steel shank is fitted with diamond-ground carbide inserts, allowing insert replacement to restore cutting performance without changing the entire holder. Does the tool conform to any standard for holder interchangeability? The tool is manufactured to DIN 4974 (ISO 9), facilitating compatibility with standard holders and simplifying integration into existing tool setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20x20mm Internal Thread Turning Tool Carbide P25/P30 60° Right-Hand WN283 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 cutting edges, a rigid 20 x 20 mm square shank and a 60° tip angle for reliable, repeatable internal thread turning; order directly via Metav Werkzeuge or consult the Metav team for compatibility and supply options. Internal thread turning tool WN283 — 20 x 20 mm, carbide P25/P30, 60° right-hand (Werner Wilke) A WN283 internal thread turning tool designed for precision internal 60° thread machining in turning applications, equipped with diamond-ground carbide cutting plates for consistent thread form. Carbide P25/P30 cutting insert 20 x 20 mm square shank 60° tip for standard thread profiles Right-hand cutting direction 210 mm overall length Precision threads with consistent profile quality The combination of P25/P30 carbide and diamond-ground cutting plates provides high dimensional stability and a defined cutting edge, which reduces the need for rework and ensures consistent 60° thread geometry. This construction supports reproducible results in series production and single-part manufacture alike. The hardened cutting plates are ground to form, so the tool maintains thread profile accuracy over repeated cuts, contributing to lower scrap rates and predictable cycle times. Rigid shank design for secure clamping and reduced vibration A 20 x 20 mm square shank and 210 mm overall length deliver the mechanical stiffness required for internal turning operations in conventional and CNC lathes. The robust shank reduces chatter and improves surface finish by maintaining tool position under load. As a result, tool life is extended and surface integrity of internal threads is improved, which benefits subsequent assembly and reduces downstream inspection effort. Straightforward integration into shop workflows Supplied to the WN283 standard and fitted on a steel shank, the tool is ready to be mounted in standard toolholders for immediate use. The right-hand cutting direction matches common turning setups, simplifying process planning and reducing setup time. Packaged in practical multiples, the tool supports predictable replenishment and keeps production moving without frequent procurement interruptions. Industrial reliability and procurement confidence Sourced from an experienced tooling specialist and offered through Metav's distribution, this tool is backed by a distribution network focused on dependable supply and quality filtering from Emmerich. Metav’s approach to democratising precision means access to a broad range of measurement and tooling products, with stable availability for workshops and industrial users. The combination of proven cutting materials and a stable supply chain supports both daily production demands and planned maintenance cycles. Contact Metav Werkzeuge for a consultation on how the WN283 internal thread turning tool fits into current tooling setups and to secure reliable supply from Emmerich. Technical data Article number: 4118655202NW Standard: WN283 Brand: Werner Wilke Zerspanungstechnik GmbH Product type: Internal thread turning tool Label: Innengewindedrehmeißel 20x20mm HM P25/P30 re. 60° Wilke Data Overall length: 210 mm Cross section: 20 x 20 mm Tip angle: 60° Cutting direction: right Packaging unit: 5 Materials and features Carbide P25/P30 Steel shank fitted with diamond-ground carbide cutting plates 60° configuration Right-hand operation FAQ What is the tip angle of this internal thread turning tool? The tool features a 60° tip angle, designed for standard internal 60° thread profiles. What are the shank dimensions and overall length? The shank measures 20 x 20 mm and the overall length is 210 mm, offering a balance of rigidity and reach. Which cutting material is used for the inserts? The tool is equipped with P25/P30 carbide cutting plates, diamond-ground for consistent edge geometry. Is this a right-hand or left-hand tool? This model is configured for right-hand cutting direction. How many pieces are supplied per packaging unit? The item is supplied in a packaging unit of 5. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20x20mm Internal Turning Tool Carbide P25/P30 Right-Hand, DIN 4973 (ISO 8) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of robust carbide P25/P30, a compact 20 x 20 mm cross-section and a minimum bore Ø 34 mm capability for reliable internal turning in production environments; order directly via Metav Werkzeuge or contact our consultants for application advice. Internal turning tool DIN 4973 (ISO 8) – 20 x 20 mm, HM P25/P30, right-hand (Werner Wilke) An internal turning tool for compact bores, fitted with diamond-ground carbide cutting plates and designed for dependable, repeatable internal machining in workshops and light industrial production. Carbide P25/P30 for robust cutting 20 x 20 mm cross-section for compact bores Right-hand cutting for standard turning Suitable for minimum bore Ø 34 mm Accurate bore turning with compact stability The 20 x 20 mm cross-section provides a stable contact profile for internal operations, reducing vibration and improving surface finish in confined spaces. Compliant with DIN 4973 (ISO 8), this design supports consistent centring and measured tool positioning, which is particularly beneficial when machining shafts, bushings or stepped bores. By combining a compact shank with rigid construction, the tool simplifies setup and maintains cutting geometry over runs, contributing to predictable cycle times and less rework in serial production. Durable carbide for consistent performance Equipped with carbide inserts in grades P25 and P30, the tool delivers a balance of wear resistance and toughness suited to a range of steels and alloyed materials. The diamond-ground finish on the cutting plates reduces built-up edge and improves chip control, which extends insert life and keeps surface integrity high. A steel shank carrying the inserts ensures secure clamping and repeatable orientation, translating into lower tooling costs per part and reliable performance across medium-duty turning tasks. Production-ready handling and integration Designed as a right-hand internal turning solution with a total length of 250 mm, the tool fits common turret and toolpost arrangements while allowing access into bores down to the minimum bore Ø 34 mm. Supplied in packaging unit: 5, it is suitable for replenishment in small workshops or for stocking at the production line. The configuration and dimensions make the tool straightforward to insert in standard holders, and its geometry supports predictable chip flow and easy post-process inspection—factors that accelerate downstream quality control and reduce machine downtime. Benefit from Werner Wilke’s carbide expertise—contact Metav Werkzeuge for tailored application support and assured supply from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: 4118610252NW Label: Innendrehmeißel DIN 4973ISO8 20x20mm HM P25/30 re. Wilke Product type: Internal turning tool Material: Hartmetall P25/P30 Manufacturer: Werner Wilke Zerspanungstechnik GmbH Core data Total length: 250 mm Cross-section: 20 x 20 mm Minimum bore diameter: 34 mm Cutting direction: right Standard: DIN 4973 (ISO 8) Features Steel shank with diamond-ground carbide cutting plates Carbide grades P25/P30 Packaging unit: 5 SKU: 4118610252NW Suitable for internal turning operations in compact bores FAQ What minimum bore diameter is required for this tool? The internal turning tool requires a minimum bore Ø 34 mm, as stated in the technical data for SKU 4118610252NW. Which carbide grades are used on the inserts? The tool is fitted with carbide plates in P25 and P30, offering a compromise between wear resistance and toughness for general steel machining. Is the tool right-hand or left-hand? This version is right-hand, designed for standard turning directions in turret and toolpost applications. Can the tool be used in automated turret systems? Yes, the geometry and shank dimensions (20 x 20 mm cross-section, 250 mm length) make it compatible with common turret holders for internal turning; reference SKU 4118610252NW for holder selection. Manufacturer: Werner Wilke Zerspanungstechnik GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20x20mm Right-Hand Hook Turning Tool Carbide P25/P30 6mm Cut Width, WN263 - Werner Wilke Zerspanungstechnik GmbH
Combine durable carbide P25/P30 cutting performance with a 6 mm grooving width and right-hand cutting for accurate, repeatable turning results; order the tool directly via Metav Werkzeuge or consult our specialists for application support. Hook turning tool 20 x 20 mm, carbide P25/P30 — right-hand (Werner Wilke WN263) The hook turning tool 20 x 20 mm, carbide P25/P30 is a right-hand grooving and turning implement engineered for stable, high-precision lathe operations in both production and workshop environments. Carbide grades P25/P30 for high wear resistance 20 x 20 mm square section for stable mounting 6 mm grooving width for precise parting Right-hand cutting, 210 mm overall length Precise groove control for consistent parting quality The combination of carbide P25/P30 and diamond-ground inserts delivers a consistent cutting edge that keeps groove geometry stable across runs. The tool’s defined 6 mm grooving width reduces secondary finishing and supports repeatable dimensional accuracy, which translates into fewer rejects and less rework. For technicians who monitor process capability, this configuration helps to maintain tight tolerances during medium- to high-volume turning tasks without sacrificing edge life. Robust shaft geometry for vibration-free turning A 20 x 20 mm square cross-section and a 210 mm overall length provide a rigid mounting interface that minimises chatter in the holder. The steel shank construction paired with the carbide cutting plates offers a secure clamping surface and improved tool stability, especially when machining interrupted cuts. Reduced vibration improves surface finish and extends the service life of the cutting edge, benefiting throughput and scheduling in busy workshops. Practical design that integrates with standard setups Equipped with diamond-ground carbide cutting plates, the tool is prepared for immediate use in compatible toolholders and is suited to routine grooving and finishing tasks on turning centres. The right-hand cutting orientation simplifies setup for standard lathe feed directions and helps to keep cycle times predictable. Clear marking of the designation and norm (WN263) supports fast identification in tool cabinets and simplifies inventory management for production planners. Contact Metav Werkzeuge today for tailored advice on toolholders and application setup for the Werner Wilke hook turning tool WN263 (SKU 4118660202NW) — our team in Emmerich can recommend the optimal configuration for the task at hand Technical data Article number: 4118660202NW Norm / Designation: WN263 Product type: Hook turning tool (Hakendrehmeißel) Manufacturer: Werner Wilke Zerspanungstechnik GmbH UID: 4118660202NW Core dimensions Overall length: 210 mm Cross-section: 20 x 20 mm Grooving width: 6 mm Cutting direction: Right-hand Materials & special features Material: Carbide P25/P30 Steel shank with diamond-ground carbide inserts Label: Hakendrehmeißel 20x20mm HM P25/P30 re. Wilke FAQ What groove width does the tool provide? The grooving width is 6 mm, as specified for the hook turning tool WN263 (SKU 4118660202NW), suitable for accurate parting and controlled chip formation. Is this tool limited to right-hand cutting only? Yes, the tool has a right-hand cutting orientation; setups should match the lathe’s feed direction for correct chip flow and cutting geometry. Which carbide grades are used and what is the benefit? The tool uses P25/P30 carbide grades; these grades offer good wear resistance and edge stability for routine turning and grooving operations on typical workshop workpieces. Which toolholder fits the 20 x 20 mm shank? The square 20 x 20 mm shank is compatible with standard 20 x 20 mm toolholders and clamping blocks commonly used on lathes and turning machines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25 x 16mm Corner Turning Tool Carbide P25/P30 Offset Right-Hand, DIN 4978 (ISO 3) - Werner Wilke Zerspanungstechnik GmbH
Benefit from a combination of diamond-ground carbide cutting edges and a stiff steel shank that deliver reliable shoulder turning under DIN 4978 (ISO 3). The right-hand orientation and compact 25 x 16 mm cross-section ensure consistent set-up and repeatable results in batch production — order directly via Metav Werkzeuge or consult the specialists for application advice. Corner turning tool – Eckdrehmeißel DIN 4978 (ISO 3), 25 x 16 mm, carbide P25/P30, right-hand – Wilke The Eckdrehmeißel DIN 4978ISO3 25x16mm HM P25/P30 re. Wilke is an offset corner turning tool for precise shoulder and profiling operations in workshop and production environments Diamond-ground carbide inserts fitted Steel shank, overall length 140 mm Conforms to DIN 4978 (ISO 3) Right-hand cutting orientation High repeatability for shoulder turning with certified geometry The corner turning assembly features cemented carbide P25/P30 inserts that are diamond-ground to a consistent edge geometry, providing stable dimensional control when machining shoulders and faces. Conformity with DIN 4978 (ISO 3) means the cutting geometry adheres to an established profile standard, reducing setup variation and supporting consistent part interchangeability. This results in fewer rejects and less rework in serial production while maintaining predictable machining behaviour. Robust shank and secure mounting for vibration resistance A sturdy steel shank with a compact 25 x 16 mm cross-section and an overall length of 140 mm delivers a rigid interface between the insert and the toolholder. The offset design increases accessibility for shoulder cuts while the right-hand orientation aligns with standard turning directions. The combination of a rigid holder and precision-ground inserts reduces chatter, improving surface finish and extending insert life — a direct benefit for shops seeking dependable daily performance. Efficient insert handling and consistent set-up The tool is supplied with diamond-ground carbide cutting plates mounted on the shank, enabling quick replacement and straightforward re-establishment of cutting geometry. Clear mechanical seating and standardised geometry shorten tool-change intervals and lower process downtime. For operations requiring repeatable set-ups across multiple machines, this toolholder design supports standardised clamping and minimal adjustment effort, helping to maintain throughput and predictable cycle times. Practical choice for workshop and small-batch production With a compact profile and standardised dimensions, this corner turning solution suits both manual lathes and CNC turret systems that accept a 25 x 16 mm holder size. The right-hand cutting direction and DIN-standard geometry make it straightforward to integrate into existing tooling families. Where space is constrained at the toolpost or turret, the offset arrangement offers improved access to shoulder features without compromising holder rigidity, supporting more efficient toolpaths and better surface integrity. For reliable shoulder turning with proven carbide performance, contact Metav Werkzeuge for tailored advice and fast supply from Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 — Metav specialists are available to discuss compatibility and delivery. Technical data Article number: 4118635152NW Product: Corner turning tool, DIN 4978 (ISO 3) Design: Offset (abgesetzt) Brand: Werner Wilke Zerspanungstechnik GmbH Key figures Overall length: 140 mm Shank cross-section: 25 x 16 mm Pack quantity: 5 pieces SKU: 4118635152NW Materials / Special features Cemented carbide P25/P30 cutting plates Steel shank with diamond-ground carbide inserts Right-hand cutting orientation Conforms to DIN 4978 (ISO 3) FAQ What material are the cutting plates made of? The cutting plates are made of cemented carbide P25/P30, offering a balance of wear resistance and toughness for general turning tasks with the Eckdrehmeißel DIN 4978ISO3 25x16mm HM P25/P30 re. Wilke (SKU 4118635152NW) Is this tool right-hand or left-hand? This corner turning tool is specified for right-hand cutting, designed to match standard right-hand turning operations. What are the shank dimensions and overall length? The holder has a 25 x 16 mm cross-section and an overall length of 140 mm, suitable for toolposts and turret systems accommodating that size. Does the tool comply with any international standard? Yes, the geometry conforms to DIN 4978 (ISO 3), ensuring standardised cutting-edge geometry for reproducible results. How many items are supplied per pack? The product is supplied in a pack quantity of 5 pieces as indicated on the product data. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25 x 16mm Grooving Tool Carbide P25/P30 6mm Cut Left DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, a 25 x 16 mm robust shank and a precise 6 mm parting width for consistent, high‑quality parting operations; order directly via Metav Werkzeuge or consult our advisers for application support. Parting tool DIN 4981 (ISO 7) — 25 x 16 mm, carbide P25/P30, left‑hand (Wilke) Parting tool DIN 4981 (ISO 7) — 25 x 16 mm, carbide P25/P30, left‑hand (Wilke) offers an industrial‑grade solution for controlled parting and grooving in turning operations across general workshop and production environments. Carbide grade P25/P30 for demanding turning Complies with DIN 4981 (ISO 7) interface 25 x 16 mm cross‑section, robust shank 6 mm parting width for precise cuts High reliability and repeatable accuracy for parting tasks The design targets repeatable results in batch and one‑off turning. With a carbide P25/P30 cutting configuration and a steel shank fitted with diamond‑ground carbide inserts, the tool offers stable edge retention and consistent cutting geometry. The adherence to DIN 4981 (ISO 7) ensures compatibility with standard toolholders, reducing setup time and enabling straightforward interchangeability in a production cell. These characteristics translate directly into higher uptime and fewer reworks when parting and grooving operations demand tight tolerances. Robust construction that supports efficient machining A substantial 25 x 16 mm cross‑section and an overall length of 140 mm provide the rigidity required for clean parting strokes, while the 6 mm parting width is tuned for narrow, material‑saving separations. The left‑hand cutting orientation suits applications where the tooling arrangement or spindle direction requires an inverse approach. Robust mechanical properties reduce chatter and deliver a superior surface finish compared with less rigid tools, contributing to faster cycle times and lower scrap rates on both small and medium series. Clear application advantages and material suitability The combination of P25/P30 carbide and diamond‑ground topography makes the tool particularly effective for steel and alloy turning where wear resistance and edge stability matter. The tool is suited for industrial workshops and specialist turning centres seeking a balance between tool life and finish quality. Where narrow parting widths and controlled chip formation are required, this configuration reduces the risk of workpiece pull‑out and supports safer separating operations, especially in automated or semi‑automated turning cells. Practical fit‑and‑use considerations for the workshop Compliance with the DIN 4981 (ISO 7) interface simplifies fixture planning and spare‑part logistics: the tool mounts into standard holders without modification. Packaged in units of five, the set‑supply approach supports predictable stock levels for maintenance teams. The left‑hand orientation and specified dimensions should be checked against existing toolholders and part programmes during setup; if necessary, consult technical documentation for holder clamping and overhang limits to preserve tool life and maintain process stability. For precise parting applications, contact Metav Werkzeuge for technical advice and availability via info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data SKU: 4118645652NW Product type: Parting tool Material: Carbide P25/P30 Cross‑section: 25 x 16 mm Parting width: 6 mm Overall length: 140 mm Cutting direction: Left‑hand Standard: DIN 4981 (ISO 7) Packaging unit: 5 Facts Overall length: 140 mm Cross‑section: 25 x 16 mm Parting width: 6 mm Packaging unit: 5 pieces Special features Carbide P25/P30 cutting configuration Steel shank fitted with diamond‑ground carbide inserts Complies with DIN 4981 (ISO 7) Left‑hand cutting orientation FAQ What materials is this parting tool best suited for? The parting tool with carbide P25/P30 is optimised for steel and alloy turning, offering good wear resistance and edge stability for typical workshop steels. Is the tool compatible with standard DIN 4981 toolholders? Yes, compliance with DIN 4981 (ISO 7) means the tool is designed for use with standard holders that accept this interface size. What is the effective parting width and why does it matter? The specified 6 mm parting width provides a narrow kerf for material savings and reduced clamping forces while maintaining chip control during separation. How is the tool supplied and what is the SKU for reordering? The item is supplied in packaging units of five and is listed under SKU 4118645652NW for easy reordering. Which direction of cut does this tool use and when is that required? This is a left‑hand parting tool; it is used where the tool must cut towards the operator’s left or in setups that require inverse cutting orientation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25 x 25mm Internal Corner Turning Tool Carbide P25/P30, Right-Hand, DIN 4974 (ISO 9) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 robustness, diamond-ground inserts accuracy and a compact 25 x 25 mm cross-section for reliable internal corner turning; order directly via Metav Werkzeuge or consult our technical team for application guidance. Internal corner turning tool DIN 4974 (ISO 9) — 25 x 25 mm, carbide P25/P30, right-hand (Werner Wilke) Internal corner turning tool DIN 4974 (ISO 9) — 25 x 25 mm, carbide P25/P30, right-hand (Werner Wilke) is designed for precision internal profiling on lathes, combining a steel shank with diamond-ground carbide inserts for consistent edge geometry in restricted bores Carbide P25/P30 grade for durability Complies with DIN 4974 (ISO 9) Steel shank with diamond-ground inserts Minimum bore 43 mm Accurate internal corner machining with standard compliance The Internal corner turning tool DIN 4974 (ISO 9) is engineered to meet the demands of internal profiling where repeatable accuracy is essential. Conforming to DIN 4974 (ISO 9) ensures a standardised fit and interface for toolholders and fixtures, while the 25 x 25 mm cross-section offers a compact footprint that still provides sufficient rigidity. The 300 mm overall length gives reach into deeper bores, subject to the stated minimum bore diameter of 43 mm, and the right-hand cutting orientation matches conventional lathe setups. These characteristics reduce the need for rework and help maintain cycle-time reliability on production and maintenance tasks. Longer service life through optimised carbide and insert finish Durability and consistent cutting geometry are achieved by the combination of carbide P25/P30 and diamond-ground inserts. The chosen P25/P30 carbide composition is selected for a balance of toughness and wear resistance suitable for finishing and semi-finishing operations, while the diamond-ground finish on the inserts promotes stable cutting edges and reduced vibration. As a result, the tool supports predictable tool life and surface quality, cutting downtime and saving costs through fewer insert changes. Routine inspection and correct clamping of the insert seats maintain peak performance and protect the cutting geometry. Practical integration into workshop processes and supply assurance With its steel shank and standardised interface, the tool integrates straightforwardly into common lathe toolposts and holders used in small-batch and series production. The compact 25 x 25 mm profile simplifies fixturing in constrained spaces, and the specified minimum bore of 43 mm clarifies applicability before setup, avoiding unsuitable configurations. Supplied in practical packaging multiples, this component benefits from Metav’s distribution model: a European quality filter and dependable logistics that support timely replenishment and consistent product availability for trade and industry. Choose Werner Wilke’s internal corner turning tool with P25/P30 carbide for dependable finishing operations and contact Metav Werkzeuge for specific application advice and supply from Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4118615302NW Designation: Inneneckdrehmeißel DIN 4974 (ISO 9) 25 x 25 mm HM P25/30 re. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Internal corner turning tool Facts Overall length: 300 mm Cross-section: 25 x 25 mm Minimum bore diameter: 43 mm Packaging unit: 3 Special features Material: carbide P25/P30 Standard: DIN 4974 (ISO 9) Steel shank with diamond-ground carbide inserts Right-hand cutting direction FAQ What bore size is required for safe use of this tool? The tool requires a minimum bore diameter of 43 mm; the Internal corner turning tool DIN 4974 (ISO 9) 25 x 25 mm (SKU 4118615302NW) is designed for operations where that clearance is available. Which carbide grade is fitted and what does it mean for performance? The fitted P25/P30 carbide offers a balance of toughness and wear resistance suitable for finishing and semi-finishing, supporting longer tool life and stable cutting. Is the insert finish significant for surface quality? Yes, the diamond-ground inserts produce a consistent cutting geometry that helps achieve superior surface finish and reduces vibration during internal profiling. Can this tool be used in standard lathe toolholders? The steel shank and the standardised dimensions (25 x 25 mm, DIN 4974) ensure compatibility with common lathe toolholders and fixtures used in workshops. What cutting direction does the tool use and why is that important? This is a right-hand cutting tool; selecting the correct cutting direction ensures proper chip flow and safe engagement with internal corners. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25 x 25mm Turning Tool Broad Straight Carbide P25/P30, DIN 4976 (ISO 4) - Werner Wilke Zerspanungstechnik GmbH
Combine reliable carbide performance with a standardised DIN interface and a rigid 25 x 25 mm cross-section for steady turning results; take advantage of quick availability via Metav Werkzeuge or consult our specialists for application advice. Wilke Turning Tool (DIN 4976 / ISO 4) 25 x 25 mm — wide, straight, carbide P25/P30 Wilke Turning Tool (DIN 4976 / ISO 4) 25 x 25 mm is a wide, straight-profile lathe cutting tool fitted with diamond-ground carbide inserts and intended for standardised lathe setups where robust, repeatable turning is required *Carbide P25/P30 for high wear resistance *25 x 25 mm cross-section for stable clamping *Diamond-ground carbide inserts fitted *Conforms to DIN 4976 (ISO 4) for standard tooling Reliable cutting life through optimised carbide grade The tool is equipped with P25/P30 carbide, a grade chosen for a balance between toughness and hardness; this combination is effective where prolonged tool life and consistent edge retention are required. The diamond-ground inserts provide a fine, sharp cutting edge that reduces surface roughness and prolongs interval times between regrinds. For workshop managers seeking predictable maintenance cycles, the selection of this carbide grade translates into lower downtime and fewer unexpected tool changes. Rigid geometry for precise set-up and repeatable results With a 25 x 25 mm cross-section and a total length of 140 mm, the design emphasises rigidity and ease of clamping, reducing chatter in medium-duty turning operations. Compliance with DIN 4976 (ISO 4) ensures compatibility with matching tool holders and fixtures, so set-up time is minimised and fixture interchangeability is straightforward. The wide profile contributes to stable contact during cuts, enabling better dimensional control on turned parts and a more consistent surface finish. Practical integration and supply reliability for production The turning cutter is supplied with factory-mounted carbide plates on a steel shank, configured for straight cutting direction, which simplifies inventory management and reduces assembly steps at the machine. Packaged in units of three, the product supports small-batch stocking while enabling quick replenishment. Confidence in continuous supply is underpinned by Metav’s distribution model, which places a quality filter at the European distribution hub in Emmerich and supports predictable delivery to the shop floor. Secure the Wilke P25/P30 wide turning tool via Metav Werkzeuge for consistent workshop performance, or contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com / +49 2822 7131930 for tailored technical advice and swift supply Technical data SKU: 4118625252NW Product type: Turning tool Label: Drehmeißel DIN 4976ISO4 25x25mm HM P25/P30 ger. breit Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Total length: 140 mm Cross-section: 25 x 25 mm Packaging unit: 3 Special features Material: carbide P25/P30 Wide execution Diamond-ground carbide inserts fitted Steel shank with mounted carbide plates Straight cutting direction Conforms to DIN 4976 (ISO 4) FAQ What materials is this turning tool best suited for? The Wilke Turning Tool (DIN 4976 / ISO 4) 25 x 25 mm is furnished with P25/P30 carbide, a grade commonly used for reliable performance in general turning tasks; its construction is aimed at broad workshop use rather than specialised exotic alloys. Is the tool compatible with standard DIN holders? Yes, compliance with DIN 4976 (ISO 4) means the cutter fits standard holders designed to that interface, allowing straightforward integration into existing tool posts and clamping systems. How does the wide profile benefit machining operations? The wide profile increases contact stability between the insert and workpiece, which reduces vibration and improves dimensional stability and surface finish during turning operations. Are the carbide plates replaceable or mounted permanently? The product is supplied with diamond-ground carbide inserts fitted on a steel shank; replacement or refurbishment can be carried out according to workshop practice for tools of this configuration. What is the delivered quantity per package? The item is supplied in a packaging unit of 3, enabling small-batch stocking and straightforward replenishment planning. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25 x 25mm Turning Tool, Carbide P25/P30 Bent Left, DIN 4972 (ISO 2) - Werner Wilke Zerspanungstechnik GmbH
Combine the robustness of solid carbide P25/P30 with a bent DIN 4972 (ISO 2) geometry and a left-hand cutting direction for dependable, repeatable turning operations; order this tool directly via Metav Werkzeuge or consult our specialists for application advice. Drehmeißel (bent) – 25 x 25 mm, solid carbide P25/P30, left-hand by Werner Wilke Zerspanungstechnik Drehmeißel DIN 4972ISO2 25x25mm HM P25/P30 li. geb. Wilke is a bent turning tool designed for precise metalcutting tasks where clearance and secure chip flow are essential Solid carbide P25/P30 grade Bent geometry to DIN 4972 (ISO 2) Left-hand cutting direction 25 x 25 mm cross-section Precise cutting performance for stable production The bent turning tool delivers consistent dimensional accuracy thanks to its solid carbide construction in P25/P30 grade. The combination of a rigid steel shank and diamond-ground carbide inserts reduces vibration and improves tool life, which supports stable cycle times and consistent surface finish. The left-hand cutting orientation suits specific lathe setups and reversing operations; the standardised geometry to DIN 4972 (ISO 2) ensures predictable engagement angles and compatibility with holders designed to this norm. These characteristics translate directly into fewer rejects and more predictable throughput for production-focused workshops. Space-saving geometry with reliable chip management The bent design provides increased clearance between the toolholder and the workpiece, enabling machining in confined setups and near shoulders without compromising accessibility. The 25 x 25 mm cross-section balances stiffness with adaptability to common toolholders, while the overall length of 140 mm is dimensioned for secure clamping and optimal reach. Diamond-ground cutting faces promote uniform chip formation and ease finishing, reducing the need for downstream rework. For operations that demand repeatable dimensions and straightforward handling, this geometry reduces setup time and supports uninterrupted machining sequences. Practical handling, maintenance and application flexibility The tool arrives with pre-mounted carbide cutting plates on a steel shank, simplifying installation and replacement during tool changes. The robust carbide grade resists wear in many general turning tasks; the bent execution assists in avoiding collisions and improving operator sightlines to the cutting zone. Left-hand cutting tools are particularly useful in specialised turning strategies and for reversing feed directions without repositioning the workpiece. Routine inspection of the diamond-ground inserts and secure clamping of the shank will maintain cutting quality and extend service intervals, contributing to lower overall operating costs. Contact Metav Werkzeuge for tailored technical advice or to request detailed compatibility information; reach out via info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application-specific recommendations and procurement options Technical data Article number / SKU: 4118605702NW Product label: Drehmeißel DIN 4972ISO2 25x25mm HM P25/P30 li. geb. Wilke Product type: Turning tool Facts Material: Hartmetall P25/P30 Cross-section: 25 x 25 mm Overall length: 140 mm Cutting direction: Left-hand Form: Bent Standard: DIN 4972 (ISO 2) Special features Steel shank with diamond-ground carbide inserts Bent execution for improved clearance Pre-mounted carbide plates Packaging unit: 3 FAQ What applications is this bent turning tool best suited for? This bent turning tool is designed for general turning operations where clearance is required; the solid carbide P25/P30 construction and diamond-ground inserts make it suitable for consistent finishing and medium-duty cutting tasks. Can the tool be used in standard DIN 4972 toolholders? Yes, the geometry complies with DIN 4972 (ISO 2), so the tool fits holders that accept this standard profile and offers predictable seating and cutting angles. Why choose a left-hand cutting direction? A left-hand cutting direction supports setups where feed and spindle rotation require reverse orientation; the left-hand characteristic of this tool helps avoid repositioning some workpieces or fixtures. How does the carbide grade influence tool life? The P25/P30 carbide grade balances toughness and wear resistance; it offers reliable durability for production runs and contributes to consistent surface quality over extended use. Is the shank configurable or supplied ready-to-fit? The tool is supplied with a steel shank fitted with diamond-ground carbide inserts, ready for mounting in compatible toolholders Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm 25x25mm Right-Hand Grooving Turning Tool Carbide P25/P30, 8mm Cut Width - Werner Wilke Zerspanungstechnik GmbH
Combining carbide P25/P30 cutting plates with a 25 x 25 mm cross-section and an 8 mm grooving width, this right‑hand hook turning tool offers precise, repeatable grooving and reliable tool life; order directly via Metav Werkzeuge or consult our specialists for application advice. Hakendrehmeißel 25x25mm HM P25/P30 re. Wilke — Right‑hand hook turning tool with carbide P25/P30 Hakendrehmeißel 25x25mm HM P25/P30 re. Wilke is a right‑hand turning tool designed for precise grooving and parting tasks where consistent cut geometry and tool life are essential Carbide P25/P30 cutting plates 25 x 25 mm robust cross-section Right‑hand cutting direction 8 mm grooving width for precise cuts Consistent grooving with industrial‑grade carbide Equipped with carbide P25/P30 cutting plates mounted on a steel shank, this hook turning tool delivers consistent groove profiles even in repetitive production runs. The designation WN263 denotes the standardised geometry that supports stable tool seating and repeatability; diamond‑ground carbide edges provide a sharper initial profile and reduce vibration, which translates into steadier surface finish and fewer reworks. Such characteristics are particularly relevant for turning operations requiring tight tolerances over long batches. Durable configuration reduces downtime The combination of a 25 x 25 mm cross‑section and the reinforced shank configuration increases stiffness at the cutting edge, lowering deflection during engagement. This stiffness, together with the wear resistance of P25/P30 grade carbide, extends the intervals between insert changes and maintenance, contributing to higher machine uptime. The tool’s build aims to provide an economical balance of tool life and cutting performance for medium‑duty steel turning and grooving operations. Easy adaptation to existing lathe setups Designed as a right‑hand tool with a 250 mm overall length, the component integrates smoothly into standard tool holders and turret stations. The 8 mm groove width is suitable for common parting and undercut profiles, allowing straightforward changeover from general‑purpose cutters without extensive fixture modification. Clear, measurable dimensions and standardised geometry mean predictable set‑up times and fewer trial cuts during process introduction. Practical performance across common workshop materials While optimised for steelwork, the tool’s carbide composition and ground cutting edges deliver reliable results across a range of applications where a robust grooving action is required. The tool’s geometry prioritises chip control and edge strength, reducing the risk of built‑up edge formation and ensuring stable performance in continuous turning cycles. The result is dependable surface quality and repeatability where production consistency matters. Quality assurance and application support Manufactured to a recognised tooling standard and supplied in practical packing units, the tool is aimed at workshops and production lines that require predictable behaviour and straightforward inventory management. The proven carbide grades and accessory specifications support quality‑centred workflows and help streamline procurement for precision turning operations. Contact Metav Werkzeuge for tailored advice on integrating this Wilke right‑hand hook turning tool into existing turning processes or for ordering information through Metav Werkzeuge. Technical data SKU: 4118660252NW Norm: WN263 Product type: Hook turning tool (right‑hand) Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Total length: 250 mm Cross‑section: 25 x 25 mm Grooving width: 8 mm Packaging unit: 3 pcs Special features Material: Carbide P25/P30 Steel shank fitted with diamond‑ground carbide cutting plates Right‑hand cutting direction Label: Hakendrehmeißel 25x25mm HM P25/P30 re. Wilke FAQ What materials is the tool suitable for? The tool, specified as a right‑hand hook turning tool with carbide P25/P30, is intended primarily for steel turning and grooving applications while offering reliable performance on common engineering materials. How wide is the grooving cut with this tool? The grooving width is 8 mm, a dimension suitable for typical parting and undercutting tasks in workshop and light industrial settings. What standard or geometry does the tool conform to? The tool follows the WN263 geometry, providing consistent seating and predictable tool behaviour in compatible holders. What is the overall length and cross‑section of the tool? Overall length is 250 mm, with a 25 x 25 mm cross‑section providing stiffness and reduced deflection during cutting. Is the cutting edge pre‑finished? Yes, the cutting plates are diamond‑ground carbide, offering a sharp initial edge and improved surface finish. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25x16mm Carbide Turning Tool Sharp Tip 80° Straight Cut DIN 4975 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of high wear resistance and a standardised shank interface to keep turning operations consistent and downtime low; combined with diamond-ground carbide inserts and an 80° tip angle this tool delivers precise edge definition and predictable cutting behaviour. Order directly via Metav Werkzeuge or request technical advice from our consultants. Turning tool DIN 4975 — 25 x 16 mm, cemented carbide P25/P30, pointed (Werner Wilke) Turning tool DIN 4975 — 25 x 16 mm, cemented carbide P25/P30, pointed (Werner Wilke) is a lathe cutting implement designed for standardised clamping and repeatable performance in workshop and production environments Cemented carbide P25/P30 for durable edges Standardised DIN 4975 shank interface Pointed 80° tip for accurate profiling Steel shank with diamond-ground inserts Longer tool life through high-grade carbide and precise geometry The Turning tool DIN 4975 25 x 16 mm, cemented carbide P25/P30, pointed combines a cemented carbide P25/P30 cutting body with an accurately shaped 80° tip to deliver extended service life and steady edge retention. The diamond-ground finish on the carbide cutting inserts reduces micro-roughness at the cutting edge, which helps to maintain consistent surface finishes and lowers the frequency of tool changes. This results in measurable process stability and reduced tooling costs in repetitive turning tasks. Reliable machine compatibility and accurate clamping Thanks to the DIN 4975 standardised shank and the robust steel shank construction, the tool integrates easily with common turret and tool-holder systems used in industrial lathes. The precise shank geometry minimises run-out and vibration, while the pointed 80° tip angle supports fine profiling and detail cuts. Where toolholders comply with the same standard, fitting is straightforward and repeatability across tool changes is improved, supporting higher first-pass yield rates in production. Practical supply and handling for workshop routines Supplied in a practical pack size, the tool is prepared for straightforward storage and replenishment on the shop floor. The combination of diamond-ground inserts and a solid mounting means predictable wear patterns and easier inspection of edge condition during routine checks. For workshop managers seeking to standardise tooling across machines, the clear specification and standard interface support stock consolidation and simpler inventory control while maintaining machining accuracy. For reliable precision and stocked availability, order through Metav Werkzeuge and contact our team for tailored advice — info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 4118620152NW Label: Drehmeißel DIN 4975 25x16mm HM P25/30 ger. spitz Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Dimensions & core data Cross-section: 25 x 16 mm Overall length: 140 mm Tip angle: 80° Standard: DIN 4975 Pack unit: 5 Materials & features Material: cemented carbide P25/P30 Form: pointed Cutting direction: straight Steel shank with diamond-ground carbide cutting inserts Product type: turning tool FAQ What is the shank standard of this turning tool? The turning tool uses the DIN 4975 standardised shank interface for secure and repeatable clamping. Which carbide grade is used for the cutting parts? The tool is equipped with cemented carbide P25/P30, chosen for its wear resistance and dimensional stability. What is the tip geometry and how does it affect results? An 80° tip angle provides defined edge geometry for precise profiling and improved surface finish in detailed turning operations. How is the tool supplied and what is the pack size? The product is supplied in a pack unit of 5, suitable for workshop stocking and scheduled tool replacement. Can this tool be used across different lathe tool holders? Compatibility is supported via the DIN 4975 shank; where holders meet this standard, the tool will fit and maintain repeatability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25x25mm Face Turning Tool Carbide P25/P30 Offset Right-Hand, DIN 4977 (ISO 5) - Werner Wilke Zerspanungstechnik GmbH
Benefit from a robust combination of a 25 x 25 mm square shank, P25/P30 carbide cutting edges and a stepped 140 mm steel holder for dependable right-hand face turning — order via Metav Werkzeuge or consult our specialists for application advice. Wilke face turning tool – 25 x 25 mm, carbide P25/P30, DIN 4977 (ISO 5) The Wilke face turning tool is a stepped, right-hand turning holder designed for precision external and face turning to DIN 4977 (ISO 5) standards, fitted with diamond-ground carbide cutting plates for stable chip control Carbide P25/P30 cutting edges 25 x 25 mm square shank Stepped steel shank, 140 mm overall length Right-hand cutting orientation, DIN 4977 compliant Consistent cutting performance for small-series and production runs Equipped with P25/P30 carbide inserts, this turning holder delivers a balance between wear resistance and toughness, which minimises tool changes and supports longer uninterrupted production cycles. The diamond-ground cutting plates provide defined cutting geometry for repeatable edge life and predictable surface finish, translating into reduced setup time and fewer rejects during serial turning operations. Stable clamping and straightforward setup reduce downtime The 25 x 25 mm square shank and stepped design ensure secure mounting in standard toolholders while improving accessibility for facing operations. The right-hand cutting orientation, combined with the steel shank construction, produces reliable rigidity and vibration damping — advantages that directly reduce chatter and improve dimensional consistency on turned parts. For workshops transitioning from general-purpose tooling, the simplified clamping geometry enables fast integration into existing tool posts. Clear material capability and standard conformity for process planning The holder is supplied to DIN 4977 (ISO 5), guiding compatibility with established turning practices and inspection routines. Material designation carbide P25/P30 indicates suitability for a wide range of steels and common non-ferrous materials where a balance of edge stability and toughness is required. The product’s design — a steel shank fitted with diamond-ground carbide plates — supports predictable cutting behaviour; technical specifications assist planning for cutting data and replacement inserts in production documentation. Discuss application requirements with Metav Werkzeuge to ensure the selected Wilke face turning tool matches the intended machining tasks; contact via info@metav-werkzeuge.com or call +49 2822 7131930 for precise guidance Technical data Article number: 4118630152NW Designation: Stirndrehmeißel (face turning tool) Brand: Werner Wilke Zerspanungstechnik GmbH Form: abgesetzt Specifications Standard: DIN 4977 (ISO 5) Overall length: 140 mm Cross-section: 25 x 25 mm Cutting direction: right-hand Packaging unit: 3 Features & materials Material: carbide P25/P30 Shank: steel shank with diamond-ground carbide cutting plates Additional info: stepped design, DIN 4977 compliance FAQ What materials can be machined with this face turning tool? The Wilke face turning tool is equipped with P25/P30 carbide plates and is suitable for a broad range of steels and common non-ferrous materials; specific limits should be confirmed against the intended workpiece material and cutting data. Is the tool supplied ready to fit in a standard toolholder? Yes, the stepped 25 x 25 mm shank and 140 mm overall length are intended for standard holders that accept square shanks and the tool is prepared for immediate mounting. Does the tool comply with recognised standards? The turning holder is manufactured to DIN 4977 (ISO 5), facilitating integration into established process documentation and quality checks. How are the carbide plates finished and why does this matter? The cutting plates are diamond-ground, which ensures precise cutting geometry and consistent edge condition, improving surface quality and extending predictable tool life. What is the packing unit for ordering and how is it delivered? The product is supplied in a packaging unit of 3; delivery and logistical arrangements can be coordinated through Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25x25mm Internal Thread Turning Tool Carbide P25/P30 60° Right-Hand WN283 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, a 25 x 25 mm rigid cross-section, and a 60° profile for consistent internal thread quality; order via Metav Werkzeuge or contact the consultants for selection guidance. Internal thread turning tool WN283 — 25 x 25 mm, Carbide P25/P30, 60° right-hand (Wilke) A Internal thread turning tool WN283 engineered for machining internal metric threads in lathes and CNC turning centres, supplied with a steel shank and diamond-ground carbide cutting inserts. Carbide P25/P30 for reliable wear resistance 25 x 25 mm cross-section for rigid setup 60° profile angle for standard metric threads Right-hand orientation; diamond-ground inserts High-performance cutting with carbide inserts for repeatable results The tool is equipped with carbide P25/P30 cutting edges mounted on a steel shank, delivering a balance of toughness and wear resistance suitable for production environments. The use of diamond-ground inserts gives a defined cutting geometry that promotes stable chip formation and predictable tool life. As a result, shops can expect improved process stability and fewer interruptions from unplanned tool changes, which supports higher overall machine utilisation and a more efficient workflow. Secure internal thread form and dimensional accuracy With a 25 x 25 mm cross-section and a 60° profile, the design focuses on rigidity and correct thread geometry for standard metric threads. The larger cross-section increases radial stiffness in internal operations, reducing deflection during plunging and profile cutting. By preserving the correct profile angle and insert geometry, the tool helps maintain thread form tolerance and surface finish, which is particularly important when producing mating components and assemblies where thread fit is critical. Practical handling and economic operation in production The cartridge-style arrangement of carbide inserts on a hardened steel shank allows straightforward replacement of cutting edges, reducing downtime and consumable cost over time. The right-hand cutting direction aligns with common lathe setups and turning centres, enabling simple integration into existing tool posts and holders. For batch production, the combination of long shank length and standard cross-section supports consistent set-ups and fast changeovers, contributing to lower unit costs and a more reliable manufacturing schedule. Secure reliable internal threading with the Wilke WN283 — contact Metav Werkzeuge for tailored advice and dependable supply from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 4118655252NW Norm: WN283 Label: Innengewindedrehmeißel 25x25mm HM P25/P30 re. 60° Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 250 mm Cross-section: 25 x 25 mm Tip angle: 60° Packaging unit: 1 Special features Material: Carbide P25/P30 Execution: 60° thread profile Cutting direction: Right-hand Steel shank with diamond-ground carbide inserts FAQ What is this tool intended for? The internal thread turning tool WN283 is designed for machining internal metric threads on lathes and CNC turning centres, providing a standard 60° profile for mating thread fits. Which cutting material is used on the inserts? The cutting edges are carbide P25/P30, presented as diamond-ground inserts mounted on a steel shank to combine edge stability with toughness. Is the tool right-hand or left-hand? This tool is supplied in a right-hand configuration for conventional turning operations. What shank size and length does the tool have? Shank cross-section is 25 x 25 mm with an overall length of 250 mm, suitable for holders that accept 25 x 25 profiles. Does the tool support standard metric thread profiles? Yes, the tool is configured for the 60° thread profile commonly used for metric internal threads. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300mm 25 x 25 Internal Turning Tool Carbide P25/P30, Right-Handed, DIN 4973 (ISO 8) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 cutting performance, a diamond‑ground carbide insert fitted on a steel shank and DIN 4973 (ISO 8) compatibility for reliable internal turning in bores from 43 mm; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Internal turning tool DIN 4973 (ISO 8) – 25 x 25 mm, Carbide P25/P30 – Werner Wilke The Internal turning tool DIN 4973 (ISO 8) is a right‑hand tool designed for precise internal turning in bores from 43 mm, featuring diamond‑ground carbide cutting plates mounted on a robust steel shank. Diamond‑ground carbide cutting plates Carbide grade P25/P30 25 x 25 mm cross‑section Right‑hand cutting, DIN 4973 compliant Consistent cutting performance from a proven carbide grade This internal turning tool is built around carbide P25/P30, a grade selected for sustained wear resistance and repeatable edge geometry. The diamond‑ground inserts provide a precisely finished cutting edge that maintains form over repeated cycles, reducing the need for frequent regrinding. Conformity with DIN 4973 (ISO 8) ensures dimensional consistency and interchangeability with compatible tool holders, which simplifies tool inventory management and supports predictable machining results in series production. Rigidity and reach that improve surface finish and stability A 25 x 25 mm cross‑section combined with a 300 mm overall length offers a well balanced compromise between reach and stiffness. The larger cross‑section increases resistance to deflection during internal cuts, helping to reduce chatter and deliver a more consistent surface finish. For operations where tolerance stability matters, the tool’s geometry translates directly into fewer rejects and less dressing time for downstream processes, supporting tighter production tolerances without complex setup changes. Easy integration and reliable mounting for workshop workflows Designed with a steel shank fitted with diamond‑ground carbide plates, the assembly plugs into standard DIN 4973 compatible clamping systems, allowing straightforward adoption into existing toolposts and turret holders. The right‑hand cutting orientation suits conventional internal turning cycles and can be used for profiling and facing inside bores. The robust construction reduces accidental insert movement, which helps to save setup time and minimises unexpected interruptions in repetitive machining tasks. Practical suitability and operational notes The tool requires a minimum bore diameter of 43 mm, which defines the lower limit for safe engagement of the cutting plates. Because the cutting plates are diamond‑ground, the geometry is already optimised for consistent chip formation and predictable wear patterns; this eases tool life monitoring and replacement scheduling. For optimal results, ensure correct clamping torque and holder alignment in accordance with DIN 4973 guidelines to retain the tool’s dimensional stability and cutting performance over extended runs. Contact Metav Werkzeuge for tailored advice and fast supply of Werner Wilke internal turning tools; call +49 2822 7131930 or email info@metav-werkzeuge.com for application support and order processing Technical data Article number: 4118610302NW Description: Internal turning tool DIN 4973 (ISO 8), 25 x 25 mm, carbide P25/P30, right‑hand Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 300 mm Cross‑section: 25 x 25 mm Minimum bore diameter: 43 mm Packing unit: 3 Standard: DIN 4973 (ISO 8) Special features Steel shank with diamond‑ground carbide cutting plates Carbide grade P25/P30 Right‑hand cutting DIN 4973 / ISO 8 compliant FAQ What is the minimum bore diameter required for this tool? The minimum bore diameter for the Internal turning tool DIN 4973 (ISO 8) is 43 mm, ensuring safe engagement of the cutting plates. What materials form the cutting system of this tool? The cutting system consists of carbide P25/P30 inserts that are diamond‑ground and mounted on a steel shank, providing wear resistance and stable edge geometry. Is the tool compatible with standard DIN 4973 holders? Yes, the tool complies with DIN 4973 (ISO 8) and is designed for direct integration into holders that follow this standard. What are the overall length and shank dimensions? The tool has an overall length of 300 mm and a shank cross‑section of 25 x 25 mm, offering the reach and stiffness needed for internal turning. Which cutting direction does the tool use? The tool is configured for right‑hand cutting and is intended for standard internal turning operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
32mm x 32mm Internal Radius Turning Tool Carbide P25/P30, Right-Hand, DIN 4974 (ISO 9) - Werner Wilke Zerspanungstechnik GmbH
Combine robust P25/P30 carbide cutting edges with a 32 x 32 mm shank and a 355 mm reach for dependable internal corner turning; order directly via Metav Werkzeuge or consult our specialists for suitability and delivery options. Internal corner turning tool DIN 4974 (ISO 9) 32 x 32 mm, carbide P25/P30, right-hand (Werner Wilke) The Internal corner turning tool DIN 4974 (ISO 9) 32 x 32 mm is a right-hand tool for precise internal corner machining in bores from 52 mm and above, supplied with diamond-ground carbide cutting inserts. Carbide P25/P30 diamond-ground inserts Cross-section 32 x 32 mm shank Total length 355 mm for deep reach Suitable for bore Ø from 52 mm Accurate corner form and consistent surface quality The tool is engineered to deliver repeatable corner geometry thanks to its carbide P25/P30 cutting edges and adherence to DIN 4974 (ISO 9). Diamond-ground inserts provide a defined cutting edge that reduces vibration and produces a consistent finish, which is especially important when internal radii must meet tight tolerances. For operations that prioritise dimensional stability, the combination of a hardened insert grade and a rigid shank minimises deflection and helps maintain the specified corner form throughout a production run. Access, setup and material handling explained A steel shank with a 32 x 32 mm cross-section and a 355 mm overall length offers the reach required for deeper bores while keeping tool overhang within practical limits. The right-hand cutting orientation is suited to standard lathe or turning centre configurations; the smallest recommended bore diameter is 52 mm, which defines the minimum workpiece aperture for safe insert engagement. The tool’s geometry supports both roughing and finishing passes where compact insert contact and controlled chip formation are needed to avoid chatter and surface damage. Efficiency in workflow and workshop integration Supplied as a set component ready to fit into standard toolholders, the item reduces machine downtime through fast insert replacement and clear specification marking. The unit count of the packaging provides practical stock handling for small to medium workshops and production cells. Where process reliability and supplier transparency matter, the combination of standardised design and robust carbide grades supports predictable tool life and planning for regrind or replacement cycles, helping to lower overall unit costs per part over time. For application advice or to secure timely delivery of the Wilke internal corner turning tool, contact Metav Werkzeuge GmbH in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility with specific materials and machinery Technical data SKU: 4118615352NW Product type: Internal corner turning tool Standard: DIN 4974 (ISO 9) Material: Carbide P25/P30 Label: Inneneckdrehmeißel DIN 4974ISO9 32x32mm HM P25/30 re. Wilke Facts Cross-section: 32 x 32 mm Total length: 355 mm Smallest bore diameter: 52 mm Cutting direction: right-hand Packaging unit: 3 Special features Steel shank fitted with diamond-ground carbide inserts Carbide cutting edges P25/P30 for general turning applications Designed for internal corner machining according to DIN 4974 (ISO 9) FAQ Which minimum bore diameter is required for this tool? The smallest recommended bore for the Wilke internal corner turning tool is 52 mm, allowing safe engagement of the carbide inserts. What carbide grade do the inserts use and what does that mean? The item is fitted with P25/P30 carbide inserts; these grades offer a balance of toughness and wear resistance suitable for a wide range of steel turning applications. Is the tool suitable for finishing passes? Yes; the diamond-ground inserts and rigid 32 x 32 mm steel shank provide the stability needed for finishing internal corners with consistent surface quality. How long is the tool and what does that affect? The total length is 355 mm, which provides extended reach into deeper bores while requiring appropriate clamping to limit overhang and deflection. How many pieces are supplied per packaging unit? The tool is supplied in a packaging unit of 3, facilitating workshop stocking and quicker replacement planning. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8 x 8mm Internal Corner Turning Tool Carbide P25/P30, Right-Hand, DIN 4974 (ISO 9) - Werner Wilke Zerspanungstechnik GmbH
Reliable finishing for confined internal profiles thanks to HM P25/P30 carbide and diamond-ground cutting plates, combined with DIN 4974 (ISO 9) compliance and a compact 8 x 8 mm cross-section; order the tool directly via Metav Werkzeuge or ask our consultants if needed Internal corner turning tool DIN 4974 (ISO 9) — 8 x 8 mm, HM P25/P30, right-hand (Wilke) Internal corner turning tool for precision internal profiling and finishing in confined bores, built to DIN 4974 (ISO 9) standards with a steel shank fitted with diamond-ground cemented carbide cutting plates Diamond-ground carbide cutting plates Complies with DIN 4974 (ISO 9) standard Minimum bore Ø 14 mm for compact applications Right-hand tool with steel shank construction High-precision geometry for repeatable internal corners The tool combines a steel shank with diamond-ground cemented carbide plates, delivering consistent edge geometry and extended tool life. The use of HM P25/P30 carbide provides a balanced mix of toughness and wear resistance, making the insert suitable for routine finishing operations where surface quality and dimensional consistency are essential. The tool’s construction reduces vibration in confined bores, which in turn improves surface finish and repeatability for internal corner features on turned components. Designed for small, confined bores and accurate profiling With a compact 8 x 8 mm cross-section and a minimum usable bore of 14 mm, the tool is optimised for internal corner work in small to medium-sized cavities. The right-hand cutting orientation suits conventional lathe set-ups where cuts enter from the workpiece face, and the overall length of 125 mm ensures sufficient reach without excessive overhang. This combination makes the insert particularly effective for producing accurate internal radii and shoulder transitions in components where accessibility is limited and precision is required. Standards, usability and maintenance explained Compliant with DIN 4974 (ISO 9), the design supports toolholder interchangeability and process standardisation across workshops. The diamond-ground plates permit easy regrinding cycles when needed; however, the carbide grade’s wear characteristics typically extend interval lengths between reconditioning for many production environments. Simple inspection of the cutting edge after defined cycle counts and routine cleaning of the shank are recommended to maintain consistent cutting performance and to protect the carbide seating. For technical advice on the Wilke internal corner turning tool with HM P25/P30, or to arrange supply from local stock in Emmerich, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or +49 2822 7131930 — expert consultants are available to confirm compatibility with specific applications Technical data Article number: 4118615052NW Product type: Internal corner turning tool Standard: DIN 4974 (ISO 9) Facts Overall length: 125 mm Cross-section: 8 x 8 mm Minimum bore diameter: 14 mm Packaging unit: 5 Special features Material: cemented carbide P25/P30 Right-hand cutting direction Steel shank with diamond-ground carbide cutting plates DIN 4974 (ISO 9) compliance FAQ What is the minimum bore diameter this tool can be used in? The tool is specified for use in bores from 14 mm; the compact 8 x 8 mm cross-section and overall length of 125 mm support machining in confined internal profiles. Which carbide grade is mounted on the insert and what are its strengths? The insert is made from HM P25/P30 cemented carbide, offering a balance of toughness and wear resistance suitable for finishing and routine internal profiling operations. Is the tool compatible with standard toolholders according to norms? Yes; the geometry follows DIN 4974 (ISO 9), enabling straightforward interchangeability with compliant toolholders and supporting process standardisation. Does the tool cut left- or right-hand? This variant is a right-hand internal corner turning tool, intended for conventional right-hand lathe cutting directions. What construction features support edge stability and surface finish? A steel shank fitted with diamond-ground carbide cutting plates reduces vibration and secures a precise cutting edge, improving surface finish and repeatability in internal features. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
8 x 8mm Internal Turning Insert HM P25/P30 Right-Hand, Fits Ø14mm Bore · DIN 4973 (ISO 8) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of diamond-ground carbide inserts, compact dimensions and a sturdy steel shank for reliable internal turning in confined bores; order directly via Metav Werkzeuge or consult our specialists for application-specific advice. Internal turning tool DIN 4973 (ISO 8) – 8 x 8 mm, carbide P25/P30, right-hand (Wilke) The Internal turning tool DIN 4973 (ISO 8) is a right-hand internal turning tool designed for precision machining of bores from 14 mm, fitted with diamond-ground carbide cutting plates on a steel shank Diamond-ground carbide inserts Suitable for bores from 14 mm Right-hand cutting direction Overall length 125 mm Consistent finish and chip control for small-bore machining The tool delivers a predictable cutting result through the use of diamond-ground carbide cutting plates in P25/P30 grades, which combine wear resistance with sufficient toughness for general steel machining. Fitted as a right-hand internal turning holder, the design supports controlled chip formation and a smooth surface finish even in restricted working spaces. The specification to the DIN 4973 (ISO 8) interface ensures compatibility with standard clamping systems, reducing set-up time and improving process reliability. Stiffness and stability for repeatable performance A steel shank with a compact 8 x 8 cross-section and an overall length of 125 mm offers a balance between accessibility and rigidity. The short overhang and square cross-section reduce vibration and deflection, which translates into longer insert life and fewer reworks. The construction supports stable cutting parameters in internal turning operations and helps maintain concentricity when machining smaller diameters, contributing to predictable cycle times and lower scrap rates. Practical integration and workshop benefits Specified for use in bores from minimum bore 14 mm, this internal turning solution is supplied in packaging unit 5, allowing for batch replenishment and straightforward inventory control. The diamond-ground inserts simplify tool preparation and produce consistent cutting edges without additional regrinding. For workshops seeking a compact, standardised boring holder that dovetails with existing toolholders and collet systems, the implement provides an efficient route to precision internal turning while minimising process variability. For application-specific recommendations or to secure a reliable supply of this Wilke internal turning tool, contact Metav Werkzeuge for tailored support from Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 4118610052NW Article name: Internal turning tool DIN 4973 (ISO 8) 8 x 8 mm HM P25/P30 right-hand Facts Overall length: 125 mm Cross-section: 8 x 8 mm Minimum bore diameter: 14 mm Packaging unit: 5 Special features Carbide: P25/P30 Steel shank with diamond-ground carbide cutting plates Right-hand cutting direction Standard: DIN 4973 (ISO 8) FAQ What is the smallest bore this internal turning tool can be used in? The internal turning tool is specified for a minimum bore diameter of 14 mm, making it suitable for compact internal turning tasks. Which carbide grade is used on the cutting plates and what does it mean? The cutting plates are P25/P30 carbide, grades chosen to balance wear resistance and toughness for steel machining; the specification supports reliable performance in general-purpose turning. Is the tool compatible with standard DIN 4973 clamping systems? Yes, the holder conforms to DIN 4973 (ISO 8) for straightforward integration with compatible toolholders and clamping equipment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com