High-precision caliper gauges for rapid, repeatable measurements
Specialist caliper gauges and quick-test probes deliver fast, reliable geometry checks in production, incoming inspection and workshop use by mechanically or digitally capturing hard-to-reach features such as deep internal grooves, bore depths, tube wall thicknesses and freeform surfaces. Their spring-loaded lever mechanism ensures a defined contact force for absolutely repeatable results independent of the operator, while ergonomic designs allow one-handed operation with the workpiece remaining in the machine or on the inspection table. Available in a range of contact shapes and probe arm geometries, these precision calipers include analogue dial options for robust continuous use and digital models with tolerance signalling and data interfaces for seamless integration into quality control systems.
0.2mm Dial Test Indicator Lever Arm, Tip Bearing, ISO 17025 Calibrated - Microtech Metrology
Combining ISO 17025 traceability with a ±0.006 mm accuracy and a compact 0–0.2 mm measurement range, this lever-type dial gauge delivers reproducible micro‑measurements for workshop and lab inspections. Order the instrument directly via Metav Werkzeuge or consult our specialists for help selecting the right configuration. Microtech Metrology lever-type dial gauge – 0–0.2 mm range, ISO 17025 calibrated The lever-type dial gauge from Microtech Metrology is designed for short‑travel, high‑precision comparative and positional measurements in toolmaking, fine engineering and quality control. ISO 17025 calibration and certificate included 0–0.2 mm measurement range for micro checks ±0.006 mm specified accuracy for precise control 40 mm dial with 0.002 mm readout resolution Traceable accuracy for consistent inspection results A calibrated instrument shortens decision paths during inspection. The supplied ISO 17025 calibration certificate ensures measurement traceability and documents conformity to recognised laboratory standards, which simplifies acceptance in supplier audits and internal quality procedures. With a specified accuracy of ±0.006 mm, the instrument supports tight tolerance checks that otherwise require slower or more complex devices; the result is reproducible data for SPC entries and a clear basis for process adjustments without lengthy reworking. Compact mechanics for reliable contact and readability Mechanically tuned for short excursions, the device combines a small measurement span with a sensitive contact system. The 0–0.2 mm range and probe 12.8 mm contact pin suit delicate tasks where minimal probe travel is desirable, while the low measurement force 0.1–0.18 N reduces deflection of thin or soft parts. Readability is enhanced by the 40 mm dial and 0.002 mm graduation, enabling quick visual assessment during batch checks. The lever geometry minimises bounce and ensures the tactile feedback needed for efficient bench work, making the instrument a practical alternative to longer test setups. Practical applications and efficiency gains in the workshop Ideal for bench, jig and fixture checks, the instrument streamlines common routines: runout checks, comparative height control and fine positional verification. In production, the compact form speeds up repetitive inspections and reduces operator fatigue, which in turn lowers the risk of handling errors. The analogue display provides immediate feedback for go/no‑go decisions, while traceable calibration means readings can be confidently used in acceptance reports. For specialised tasks, the lever gauge integrates easily into clamping fixtures or height gauges to extend measurement capability without complex retooling. For specification matching, traceability or purchase, contact Metav Werkzeuge for tailored advice on this Microtech Metrology lever‑type dial gauge and its best use in the existing measurement workflow. Technical data Article number: 120131020 GTIN: 4061905453786 Manufacturer: Microtech Metrology Category: Dial gauges Facts Measurement range: 0–0.2 mm Resolution/readability: 0.002 mm Accuracy: ±0.006 mm Dial diameter: 40 mm Special features ISO 17025 calibration and certificate included Measurement force: 0.1–0.18 N Probe length: 12.8 mm Reversal span: 1.5 mm Analog lever-type dial indicator FAQ What calibration documentation is supplied with the instrument? The instrument is delivered with an ISO 17025 calibration certificate from Microtech Metrology, providing laboratory‑traceable results for audit and quality records. Is the gauge suitable for checking small runout or eccentricity? Yes, the lever‑type dial gauge with its 0–0.2 mm range and ±0.006 mm accuracy is well suited to short‑travel runout and eccentricity checks on small shafts and assemblies. How fine is the display resolution and how does that affect readings? The large 40 mm dial offers a 0.002 mm graduation for fine, rapid readings; this improves repeatability in visual inspections and speeds up batch sampling. Can the instrument be integrated into fixtures or height gauges? The compact lever geometry and probe length of 12.8 mm allow straightforward mounting in fixtures or onto height gauges for comparative or reference measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
0.5, 1.0 mm Gauge Plate Set For M208.021, 2 Pieces - Metav IndustryLine
Take advantage of a compact, two-piece calibration solution that delivers defined increments of 0.5 mm and 1.0 mm for reliable adjustment of precision instruments; order directly via Metav Werkzeuge or consult our experts for specification advice. Gauge shim set M208.021.PS – precision shims 0.5 & 1.0 mm (Metav IndustryLine) The gauge shim set M208.021.PS is a compact accessory designed to provide defined, calibrated increments for adjustment and verification of precision measuring instruments, in particular instruments of the M208.021 series. Precision shims 0.5 mm and 1.0 mm Two-piece calibration set Compatible with M208.021 measuring device Ensuring repeatable adjustments with defined shim thicknesses The set comprises two precision shims with defined thicknesses of 0.5 mm and 1.0 mm, enabling straightforward, repeatable adjustments during calibration and setup tasks. By working with discrete, known increments, measuring points and reference surfaces can be aligned more consistently, reducing setup time and variability in quality checks. This benefit is especially relevant in environments where small deviations affect downstream assembly or testing, and where traceable step changes simplify process documentation. Designed for compatibility and quick integration into calibration routines As an accessory tailored to the M208.021 family, the shims install and remove without modification to the instrument, allowing rapid checks between measurement runs. The two-piece set format keeps the toolset compact and transportable, while the low mass supports minimal handling effort. For workshops and inspection benches that require frequent verification, this set streamlines routine procedures and reduces the chance of using improvised or mismatched gauge blocks that can introduce error. Practical use in workshop and inspection workflows The shims suit short, focused tasks such as verifying an instrument zero, checking gauge spacing or setting up fixtures where a small, defined offset is required. Stored together, the set supports predictable workflow patterns during assembly and maintenance. Metav’s position as a precision partner emphasises consistent availability and reliable documentation: advice is offered for application questions, and the accessory integrates into established measurement routines without complex training or special fixtures. Secure the Metav IndustryLine gauge shim set via Metav Werkzeuge for dependable calibration support — contact Metav Werkzeuge for tailored advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M208.021.PS GTIN: 4054469146706 Label: Passscheibensatz, 2 Stück, 0,5, 1,0 mm für 208.021 Facts Weight: 0.02 kg Pieces per set: 2 Tariff number: 90179000 Special features Compatible with M208.021 measuring instrument Two precision shims: 0.5 mm, 1.0 mm Accessory category: Measuring devices / accessories FAQ What thicknesses are included in the set? The set contains two precision shims with thicknesses of 0.5 mm and 1.0 mm for defined calibration steps. Is this set suitable for the M208.021 instrument? Yes, the gauge shim set M208.021.PS is specified for use with the M208.021 measuring device and fits without modification. How is the set supplied and how many pieces are included? The accessory is supplied as a two-piece set; the package contains two shims in the stated thicknesses. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.5/1/2/3 mm Shims Set For M208 Series Accessories - Metav IndustryLine
Take advantage of precise, stackable thicknesses and direct compatibility with the M208 instrument family to simplify setup and calibration. The combination of repeatable spacing, compact handling and immediate availability through Metav Werkzeuge supports efficient metrology workflows — order via Metav Werkzeuge or contact their consultants for tailored advice. M208.054.PS Pass shim set — precision shims 0.5–3 mm M208.054.PS is a compact set of pass shims designed for fine adjustment and spacing in internal measuring and inspection devices, compatible with the M208 series of instruments. Precision shims 0.5 / 1 / 2 / 3 mm Compatible with M208 series instruments Fine thickness tolerance for accurate spacing Lightweight and easy to handle Consistent adjustments for repeatable measurement results The set supplies precision thicknesses of 0.5 mm, 1 mm, 2 mm and 3 mm, enabling controlled stacking to achieve exact clearances during instrument setup. Used as spacing or feeler elements, these shims improve repeatability by removing guesswork from assembly and calibration tasks. In workshops where reproducible results are required, the measured increments allow technicians to set and document clearances without prolonged trial-and-error, reducing set-up time and downtime. Compatibility and practical handling for metrology benches Designed specifically for the M208 series, the shims integrate cleanly with the associated internal fine-measuring devices listed in the product description. The compact format and low mass support straightforward handling and quick insertion into adjustment points; this practicality benefits inspection stations that require rapid changeover. Clean edges and uniform thickness simplify stacking and prevent lateral displacement, which helps maintain the dimensional relationships established during calibration. A useful accessory for inspection and maintenance routines As an accessory set for precision instruments, this shim assortment is ideal for workshop calibration checks, fixture shimming and small assembly corrections. Where small dimensional increments make a measurable difference to fit or function, the set offers a controlled approach to tolerance correction. The compact nature of the set means it is suitable as a spare or dedicated kit at measuring benches, ensuring that precise increments are always at hand when working on detailed internal measurements with M208 instruments. For reliable, repeatable spacing in precision measurement tasks, order the Metav IndustryLine M208.054.PS pass shim set via Metav Werkzeuge or speak to their consultants at info@metav-werkzeuge.com / +49 2822 7131930 for application advice and fast supply. Technical data Article number: M208.054.PS GTIN: 4054469178998 Weight: 0.02 kg Tariff number: 90179000 Pieces per set: 4 Core specifications Thicknesses: 0.5 mm, 1 mm, 2 mm, 3 mm Set type: Pass shim set Category path: Measuring instruments / Accessories Compatibility & features Compatible models: M208.022, M208.023, M208.024, M208.025, M208.052, M208.054, M208.424, M208.427 Intended use: Spacer / shim for internal fine-measuring devices Packaging: set format FAQ Are these shims compatible with other M208 instruments? The shims are specified for use with the M208 family noted in the description and will fit the listed M208 models; compatibility with other variants should be checked against instrument dimensions. What thicknesses are included in the set? The set contains shims in 0.5 mm, 1 mm, 2 mm and 3 mm, intended for stacking to achieve intermediate clearances. Can these shims be used for calibration adjustments? Yes — the pass shims serve as controlled spacers for calibration and setup tasks on internal measuring devices, aiding reproducible adjustments. Is the set suitable for routine workshop use? The compact, low-mass design makes the set well suited to inspection benches and maintenance work where small, accurate adjustments are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.5mm Gauge Shim For M208.019 - Metav IndustryLine
Take advantage of the precise 0.5 mm thickness and direct compatibility with the M208.019 measuring instrument to achieve repeatable setup adjustments. The compact format and low mass minimise handling overhead in frequent calibration tasks. Order the gauge shim directly via Metav Werkzeuge or ask our consultants if clarification is needed. Gauge shim 0.5 mm for M208.019 — Metav IndustryLine accessory The gauge shim 0.5 mm for 208.019 is a compact calibration accessory intended for precise spacer and alignment tasks on the corresponding M208.019 measuring device. 0.5 mm nominal thickness shim Compatible with M208.019 measuring instrument Lightweight 0.02 kg construction Fast, verifiable alignment for measurement setups The slim 0.5 mm shim provides a simple and reliable way to set gaps and offsets during instrument setup, enabling repeatable adjustments without complex fixtures. As a dedicated accessory for the M208.019 series, it removes ambiguity from small clearance settings and supports routine verification steps. The focused function of this part reduces calibration cycle time and contributes to consistent measurement outcomes in workshop and inspection contexts. Minimal handling, lower downtime Weighing just 0.02 kg, the shim’s low mass makes it easy to position and swap during inspection workflows, which in turn shortens changeover times between measurement tasks. The simple geometry keeps handling straightforward and reduces the risk of introducing unintended leverage or torsion during placement. This makes the accessory especially useful where multiple, rapid adjustments are required and where efficiency in the metrology loop directly impacts productivity. Clear traceability and ordering identifiers Identification is simplified via the product code SKU M208.019.PS and GTIN 4054469146690, which help to eliminate ordering errors and speed procurement. As an item categorised under measuring-instrument accessories, this part is intended for integration into existing inspection sets and calibration benches. The explicit linkage to the M208.019 platform ensures compatibility information is immediately apparent on technical lists and in spare-part inventories. Practical addition to a quality-focused workshop As a small but functional element in the measurement chain, this shim supports regular maintenance and set-up routines without adding complexity. Supplied as an accessory within the Metav IndustryLine range, it benefits from Metav’s role as a quality filter for the European market, which helps to make precision tooling and accessories accessible for everyday industrial use. The component is suited to environments where straightforward, repeatable adjustments are required as part of a disciplined measurement regime. For ordering or detailed application advice regarding this Metav IndustryLine gauge shim, contact Metav Werkzeuge in Emmerich — they can assist with availability and product matching to specific measuring systems Technical data Article number: M208.019.PS GTIN: 4054469146690 Category: Measuring instrument accessory Label: Gauge shim 0.5 mm for 208.019 Tariff code: 90179000 Weight: 0.02 kg Facts Thickness: 0.5 mm Mass: 0.02 kg SKU: M208.019.PS GTIN: 4054469146690 Special features Compatibility: designed for M208.019 Intended use: spacer / alignment / calibration accessory Product family: Metav IndustryLine Packaging: single spare part (packaging details not specified) FAQ What is the primary use of this shim? The gauge shim 0.5 mm for 208.019 is used as a precision spacer to set or adjust small gaps and offsets during instrument setup and alignment procedures. Is this shim compatible with other instruments? Compatibility is specified for the M208.019 measuring instrument; use with other devices should be verified against the other device’s specifications before application. Is a calibration certificate supplied with the shim? The provided product information does not indicate a calibration certificate for the gauge shim 0.5 mm for 208.019. Which identifiers should be used when ordering spare parts? Order using SKU M208.019.PS or GTIN 4054469146690 to ensure correct identification of this accessory. Is the material of the shim indicated? Material is not specified in the available product data for the gauge shim 0.5 mm for 208.019 Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.5–6mm Gauge Shim Set, 5 Pieces For Internal Fine Measuring Devices - Metav IndustryLine
Take advantage of the combination of compatibility with the M208 series, fine thickness increments and compact handling for dependable setup and repeatable measurements; order the M208.026.PS directly via Metav Werkzeuge or contact our consultants for tailored advice. M208.026.PS shim set — 5-piece set, thickness range 0.5–6 mm (Metav IndustryLine) M208.026.PS is a compact shim set designed for fine internal measurement adjustments and compatible with the M208 series of internal measuring instruments. Compatible with M208 models 025/026/425/426/428/429 Range 0.5–6 mm for fine adjustments Five-piece set for precise spacing Total weight approx. 0.02 kg Precise increments for repeatable internal adjustments The shim set supplies a controlled series of thicknesses (0.5, 1, 2, 3 and 6 mm) that make incremental spacing and shimming tasks straightforward and reproducible. Used alongside M208-series internal fine measuring instruments, these shims reduce ambiguity during setup and allow technicians to establish exact clearances without iterative grinding or guesswork. The measured increments translate directly into improved process stability and fewer setup reworks. Compact design that supports workshop efficiency Small footprint and negligible mass (approx. 0.02 kg total) mean the kit is simple to store in a tool drawer or instrument case and takes minimal space on the bench. The set format avoids searching for individual sizes during adjustments and speeds up changeovers in both prototyping and small-batch production. By providing an organised assortment of spacing shims, the kit streamlines alignment tasks and contributes to shorter machine downtime between operations. Practical handling and application guidance Shims are intended for use as spacing and calibration aids in internal measurement and fine adjustment workflows; they slot between components or into fixtures to correct play, set precise offsets or simulate final assembly clearances. Handling is intuitive: select the required thickness, confirm fit with the associated measuring instrument and lock the assembly in place. This methodical approach yields consistent measurement conditions and supports traceable adjustments across repeated assemblies. For precision shimming and reliable internal measurement setup, contact Metav Werkzeuge to obtain the M208.026.PS shim set or to discuss which configurations best suit specific instruments — eMail: info@metav-werkzeuge.com · Tel: +49 2822 7131930 Technical data SKU: M208.026.PS GTIN: 4054469146713 Customs tariff number: 90179000 Total weight: 0.02 kg Pieces per set: 5 Core numerical data Thicknesses: 0.5 mm, 1 mm, 2 mm, 3 mm, 6 mm Piece count: 5 Weight (approx.): 0.02 kg Compatibility & special features Compatible models: M208.025, M208.026, M208.425, M208.426, M208.428, M208.429 Intended use: internal fine measurement adjustments and spacing Delivery form: set for organised storage FAQ What sizes are included in the shim set? The M208.026.PS contains shims of 0.5 mm, 1 mm, 2 mm, 3 mm and 6 mm thickness for stepped adjustments. Which instruments are these shims compatible with? The set is compatible with the M208 series internal measuring instruments, including models 025, 026, 425, 426, 428 and 429. How does the set improve measurement repeatability? Using defined shim increments from the M208.026.PS reduces the need for iterative adjustments, creating stable, repeatable offsets and improving setup reproducibility. Is the kit suitable for workshop storage and transport? Yes; the compact, lightweight format of the M208.026.PS makes it suitable for organised storage in instrument cases or tool drawers. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
0.8mm Dial Test Indicator Tip‑Mounted 0.01mm Resolution ISO 17025 Calibration - Microtech Metrology
Take advantage of reliable, workshop-ready precision combined with traceable ISO 17025 calibration and compact handling for rapid small-displacement inspection; order directly via Metav Werkzeuge or consult our specialists for application advice. Microtech Metrology lever-type dial test indicator — 0.01 mm resolution, 0–0.8 mm range The Microtech Metrology lever dial test indicator is a compact analogue instrument designed for precise deflection measurement in fine mechanical and inspection tasks, ideal for bench testing, jig set-up and small‑part quality control. ISO 17025 calibrated with certificate included Resolution 0.01 mm for fine readings Compact 32 mm dial and pivoted stylus Low measuring force 0.1–0.18 N for delicate parts Precision in the smallest increments for repeatable checks This lever indicator delivers 0.01 mm resolution across a measuring span of 0–0.8 mm, making it suitable where tiny displacements must be detected reliably. The analogue dial with a 32 mm diameter provides a clear, fast visual reference for run‑out and alignment work; the instrument’s low measuring force (0.1–0.18 N) reduces influence on soft or lightweight components. Because the mechanism is tip‑bearing, contact repeatability is improved for micro‑motions and delicate probes, which supports consistent results during process verification and short inspection loops. Ready for audit and production: traceable calibration and dependable performance Delivered fully calibrated in accordance with ISO 17025, the instrument arrives with a calibration certificate, enabling immediate use in quality control processes that require documented traceability. This calibration status simplifies incoming inspection and audit procedures and reduces preparation time before first use. The combination of a certified calibration and a compact lever mechanism makes the unit a practical choice for laboratories and workshops seeking verified measurement data without lengthy setup or external reconditioning. Ergonomic layout and application benefits that reduce cycle time A compact form factor and a pivoted stylus geometry support rapid positioning in tight fixtures and narrow bores, while the modest probe dimension (taster 12.8 mm) eases access to confined features. The instrument’s quick visual feedback shortens inspection cycles and minimises handling errors during repetitive checks. For tasks such as small‑part inspection, fixture set‑up or comparative checks against master gauges, this indicator enhances throughput by delivering unambiguous read‑outs with minimal operator influence. Contact Metav Werkzeuge for ordering the ISO 17025‑calibrated Microtech Metrology lever indicator from stock and for tailored advice on integrating this instrument into existing inspection routines. Technical data Article number: 120131080 GTIN: 4061905453342 Manufacturer: Microtech Metrology Data Measuring range: 0–0.8 mm Resolution: 0.01 mm Dial diameter: 32 mm Measuring force: 0.1–0.18 N Probe (taster): 12.8 mm Display type: analogue Accuracy: 0.01 mm SKU: 120131080 Special features ISO 17025 calibration and certificate included Tip / pivoted stylus bearing Compact design for tight access Low measuring force for delicate components FAQ Is the instrument supplied calibrated and traceable? Yes. The lever‑type dial test indicator is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate for traceability. What measurement span and resolution does the indicator offer? The instrument covers a measuring range of 0–0.8 mm with a resolution of 0.01 mm, suitable for fine displacement and run‑out checks. Can the indicator be used on delicate or soft materials? Yes. With a measuring force between 0.1 and 0.18 N and a pivoted stylus, the indicator is appropriate for inspections where low contact force is required to avoid part deformation. Is the dial easy to read in a busy workshop environment? The 32 mm dial provides a clear analogue display for quick visual assessment during setup and repetitive inspections. What applications are typical for this type of instrument? Typical uses include bench inspection, jig and fixture set‑up, comparative checks on small components and run‑out measurement in fine mechanical production. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
10 mm Outside Quick Probe 0.01 mm Resolution With Rounded Tips, Delivered In Case - Metav IndustryLine
Take advantage of the combination of precise readings, a compact probe geometry for narrow grooves and a rapid-action measuring mechanism for faster inspection cycles. Order the gauge directly via Metav Werkzeuge or consult the Metav team for application advice and availability. M209.041 Outside Quick-Action Test Indicator — 0–10 mm, 0.01 mm The M209.041 is an outside quick-action test indicator engineered for fast measurement of external grooves and similar features in workshop and quality-control environments. 0.01 mm resolution for precise readings 0–10 mm external measurement range Rounded probe tips R0.5 for narrow grooves Rapid-action mechanism for quick checks Fast, repeatable groove measurement for production use The M209.041 delivers a rapid-action response that makes repetitive checks significantly more efficient on the shop floor. With a focused design for external grooves and similar features, the mechanism enables swift contact and an immediate analogue reading, reducing cycle time during serial inspections. The combination of a short probe travel and a smooth acting contact system supports repeatable positioning, which in turn improves throughput without sacrificing reliability. High-resolution readout that supports confident decisions Equipped with a 0.01 mm graduation and an industrial-grade accuracy of ±0.02 mm, the indicator provides fine visual resolution for standard machining and inspection tasks. The analogue display avoids latency and batteries while providing a clear mechanical reference that is widely understood in production environments. This level of performance is suitable for routine quality control and set-up tasks where measurable tolerances must be confirmed quickly and unambiguously. Compact probe geometry optimised for confined features The instrument's rounded probe tips R0.5 and narrow contact geometry are specifically chosen for measuring tight or curved grooves where conventional contacts cannot reach reliably. The compact construction also makes the gauge straightforward to position in restricted areas, while the modest mass contributes to stable readings during manual handling. These design choices help maintain measurement integrity when dealing with small external slots, grooves or steps on components. Workshop-ready delivery and practical handling The indicator is supplied ready for workshop use and includes a protective case for secure transport and storage. The robust mechanical construction, paired with the analogue display, makes the instrument low-maintenance and durable under normal workshop conditions. As a branded Metav IndustryLine product, it complements a broader set of measuring tools stored and supplied from Emmerich, ensuring dependable availability and consistent quality for industry and trade. Contact Metav Werkzeuge today for advice on applying the Metav IndustryLine M209.041 in production or to arrange purchase and delivery from Emmerich. Technical Data Article number: M209.041 GTIN: 4061905046803 Manufacturer: Metav IndustryLine Facts Range: 0–10 mm Resolution: 0.01 mm Accuracy: ±0.02 mm Weight: 0.66 kg Reading type: analogue Special features Rounded probe tips R0.5 Rapid-action measuring mechanism Suited for external grooves and narrow features Supplied in protective case FAQ What measurement tasks is this indicator suited for? The M209.041 is intended for external groove and narrow-feature checks, offering a 0–10 mm range suitable for small to medium external measurements. How precise is the reading on this instrument? The indicator provides a 0.01 mm graduation with an overall accuracy of approximately ±0.02 mm, delivering clear resolution for standard workshop inspection tasks. Are the rounded probe tips suitable for curved grooves? Yes, the rounded tips (R0.5) are designed to access narrow and curved grooves while minimising local damage to the measured feature. Does the instrument come protected for transport? The gauge is supplied with a protective case to ensure secure transport and organised storage within the workshop. Is the device ready for immediate use on arrival? The indicator arrives prepared for workshop use; for further details on preparation or calibration options, Metav Werkzeuge can provide guidance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10-18mm Digital Internal Micrometer 0.01mm Resolution Reversible Measurement Force ≤2.2N In Case - Metav IndustryLine
Benefit from the combination of a compact 10–18 mm measurement range, a digital display with 0.01 mm resolution and a reversible measuring direction for flexible internal checks; order the instrument directly via Metav Werkzeuge or consult our specialists for technical advice. Digital internal fine measuring instrument 10–18 mm — digital dial, 0.01 mm resolution The Digital internal fine measuring instrument 10–18 mm is a compact digital gauge designed for precise internal diameter inspection in fine mechanical and watchmaking applications. Compact 10–18 mm internal range Digital display with 0.01 mm resolution Reversible measuring direction for flexibility Precision that reduces rework and inspection time The instrument offers a digital display with 0.01 mm resolution and a declared accuracy of 0.01 mm, which establishes a clear, measurable basis for pass/fail decisions in small-bore inspection. The preset function enables a rapid zero or reference value to be set, speeding repeated checks and reducing handling steps. The specified measurement force ≤ 2.2 N limits the influence of operator pressure on readings; a lower, consistent contact force helps to maintain stable contact without deforming delicate parts, improving throughput and lowering the risk of rework. Compact design tailored to micro applications Classified in the Micro range (maximum measuring range 10–100 mm), this gauge is optimised for fine mechanical work where short jaws and high stiffness matter. The 10–18 mm span covers many common small bores in watchmaking, precision fittings and miniature components, while a measuring depth of 100 mm allows access into recessed features. The matt‑chromed device holder and compact probe geometry make the tool easy to position in tight spaces, supporting accurate, repeatable internal measurements even on small workpieces. Practical functions that support shop‑floor quality control Practical features include a reversible measuring direction for left- or right‑hand routines, a preset option for quick reference setting and a digital dial suited to rapid readout. The instrument is supplied with a set of measuring pins that cover the 10–18 mm span in defined steps, enabling fast selection of the closest probe for a given bore. Together these functions create a workflow-friendly gauge that integrates into incoming inspection, assembly checks and final control processes, improving documentation speed without adding complexity. Contact Metav Werkzeuge for personalised technical guidance or to arrange an inspection at our Emmerich quality centre; our specialists will advise on fit-for-purpose use and measurement routines Technical Data Article number: M208.260 Type: Digital internal fine measuring instrument, 10–18 mm Resolution: 0.01 mm Accuracy: 0.01 mm Measuring range: 10–18 mm Measuring depth: 100 mm Measurement force: ≤ 2.2 N Measuring pin diameter: 3.5 × M 3.5 Preset function Reversible measuring direction Facts Measuring range min: 10 mm Measuring range max: 18 mm Display resolution: 0.01 mm Pass gauge / feeler: 0.5 mm Measuring pin set: 9 × positions covering 10–18 mm (±0.6 mm reference) Special features Digital dial for direct readout Matt‑chromed device holder Preset (initial value set) Reversible measurement direction Suitable for micro internal diameter inspection FAQ What measurement range does the instrument cover? The instrument covers internal diameters from 10 mm to 18 mm, making it suitable for micro‑range inspection tasks. What resolution and accuracy are provided by the gauge? The digital readout shows 0.01 mm steps and the declared accuracy is 0.01 mm, enabling clear pass/fail decisions on small bores. Is the measuring direction fixed or reversible? The measuring direction is reversible, allowing the gauge to be used comfortably in different orientations and setups. What depth can be reached with this instrument? A measuring depth of 100 mm permits access into moderately recessed bores and features. How is repeatability handled for short‑run checks? The instrument includes a preset function and a consistent measurement force (≤ 2.2 N) to support repeatable readings during serial checks. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10-18mm Internal Micrometer Carbide Faces, 0.001mm Vernier, 110mm Depth - Microtech Metrology
Compact precision, robust contact surfaces and an easily readable mechanical indication combine to deliver repeatable internal measurements; the instrument offers 0.003 mm accuracy, 0.001 mm resolution and carbide measuring faces for long service life. Order the internal fine measuring instrument via Metav Werkzeuge or consult their specialists on suitability and availability. Internal fine measuring instrument — 0.003 mm accuracy, 10–18 mm range (Microtech Metrology) Internal fine measuring instrument for precise internal diameter inspection in micro‑assembly and precision engineering applications High accuracy 0.003 mm Resolution 0.001 mm Carbide measuring faces Measuring range 10–18 mm Laboratory-level accuracy for critical internal measurements The analogue gauge delivers a verified accuracy of 0.003 mm with a reading step of 0.001 mm, providing a clear and technically sound basis for tight‑tolerance work. Such resolution and repeatability reduce uncertainty in inspection routines and quality control documentation; the instrument’s measurement capability is suitable where small deviations would otherwise compromise fit or function. The mechanical construction is designed to keep measurement forces consistent, thereby limiting operator‑induced variance and supporting reproducible results across inspection cycles. Micro-range geometry that suits small bores and delicate components Classified for the micro measurement band (10–100 mm), this instrument covers a 10–18 mm measuring range while keeping the gauge compact and torsion‑resistant. The combination of a short measuring span and a 110 mm measuring depth enables access to internal features on small housings, watch components and precision inserts without sacrificing stability. The result is improved handling and faster inspection of small parts, making it a sensible choice for laboratories and workshops that routinely inspect miniature bores and internal profiles. Durable contact surfaces and uncomplicated handling for everyday precision Equipped with carbide measuring faces, the instrument resists wear and maintains nominal geometry under repeated contact, which lowers the need for frequent replacement and helps preserve traceability. The analogue readout remains robust in workshop environments and is simple to interpret during fast inspection sequences; mechanical design prioritises straightforward operation and maintenance. Manufactured to a professional standard by Microtech Metrology, the gauge balances longevity and measurement integrity for routine use in production inspection or final acceptance testing. For micro‑range internal measurement needs, ask Metav Werkzeuge in Emmerich about supply and technical fitment for the Microtech Metrology internal fine measuring instrument (SKU 132018800) and arrange delivery from local stock. Technical data Article number: 132018800 GTIN: 4061905454165 Category: Fine measuring instruments Manufacturer: Microtech Metrology Facts Accuracy: 0.003 mm Resolution: 0.001 mm Measuring range: 10–18 mm Measuring depth: 110 mm Special features Carbide measuring faces Analogue instrument Compact micro‑range design Intended for internal diameter measurement FAQ What accuracy and resolution does the instrument provide? The internal fine measuring instrument delivers an accuracy of 0.003 mm and a resolution of 0.001 mm, allowing fine discrimination of internal dimensions for precision inspection. Which measurement range does this gauge cover? This gauge operates over a 10–18 mm measuring range, categorised in the micro band for compact and small‑bore applications. Are the measuring faces wear‑resistant? Yes; the instrument is fitted with carbide measuring faces, which enhance wear resistance and help maintain measurement integrity over extended use. Can this instrument reach recessed internal features? With a measuring depth of 110 mm, the instrument is suitable for accessing many recessed bores and internal features typical in precision components and assemblies. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
10-18mm Internal Micrometer Carbide Measuring Faces, 0.003mm Accuracy, 110mm Depth - Microtech Metrology
Take advantage of precise internal measurement, rugged carbide contact faces and seamless data transfer to accelerate quality control. Order the instrument directly via Metav Werkzeuge or consult the team for application support and integration advice. Internal fine measuring instrument — inside micrometer with 1.54" colour touchscreen and Wireless+USB (Microtech Metrology) The Internal fine measuring instrument is a compact inside micrometer designed for high‑precision internal dimension checks in workshops, toolrooms and metrology benches High accuracy 0.003 mm Carbide measuring faces Wireless and USB data output Colour 1.54" touchscreen display Precision that reduces rework and speeds inspection The instrument delivers a rated accuracy of 0.003 mm (3 µm), providing a measurable reduction in uncertainty for fine internal measurements. Built for the Micro measuring class (max. 10–100 mm range), this size band combines reach and rigidity ideal for small bores, micro parts and precision fixtures. The tight tolerance capability supports statistical process control and reduces the need for repeat checks, which translates directly into higher throughput and fewer rejects in serial or batch production. Durable contact surfaces and practical reach for internal bores Equipped with carbide measuring faces, the device maintains consistent contact geometry over extended use, resisting wear where repeatability matters most. A 110 mm measuring depth enables access to deeper bores and stepped internal features without resorting to specialised gauges. The mechanical measuring backbone paired with hardened contact faces gives a stable reference that holds up to routine workshop handling while keeping measurement variance low. Integrated data handling that fits modern workflows The hybrid construction combines traditional mechanical measurement with contemporary data tools: a 1.54" colour touchscreen for intuitive readout and parameter control plus Wireless+USB output for direct transfer to inspection software or SPC systems. This connectivity removes transcription steps and reduces input errors, enabling traceable digital records and straightforward integration into production documentation. The device’s analogue feel with electronic capture keeps operator ergonomics familiar while delivering modern traceability. Ready for bench and production use, backed by Metav Designed by Microtech Metrology, this inside micrometer pairs fine instrument craftsmanship with practical workshop features. The balance of compact size, robust contacts and digital data output makes it suitable for quality labs, precision workshops and assembly lines that require reliable internal measurements. Metav’s distribution and support network ensures supply continuity and practical advice for implementation, reflecting a commitment to democratising precision across European workshops. Contact Metav Werkzeuge today to discuss how the Microtech Metrology internal fine measuring instrument with 0.003 mm accuracy and Wireless+USB data transfer can be specified for your inspection routine; call +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: 132018700 GTIN: 4061905454097 Manufacturer: Microtech Metrology Category: Fine measuring instruments Facts Measuring range: 10–18 mm Accuracy: 0.003 mm Measuring depth: 110 mm Display: Colour 1.54" touchscreen Data output: Wireless + USB Analogue reading: yes Special features Carbide measuring faces Hybrid analogue/electronic design Compact size for micro internal measurements Suitable for workshop and lab use FAQ What accuracy does the instrument achieve? The internal fine measuring instrument by Microtech Metrology (SKU 132018700) provides an accuracy of 0.003 mm, suitable for micro‑precision internal checks. Which measuring range and depth are covered? The device covers an internal range of 10–18 mm with a measuring depth of 110 mm, placing it in the micro class for fine mechanical work. How is measurement data exported? Data transfer is possible via Wireless and USB interfaces, allowing direct capture into inspection software and SPC systems from the Microtech Metrology instrument. Are the contact faces durable for repetitive use? Yes. The instrument features carbide measuring faces, chosen to resist wear and maintain repeatability over long series of measurements. Is this instrument intended for workshop use or laboratory calibration? The instrument is designed for both workshop and lab environments; it combines a robust mechanical feel with electronic data output for quality control applications. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
10-30mm Digital External Dial Indicator 0.005mm Reading, Rotating Display, Round Tips, Supplied in Case - Metav IndustryLine
Take advantage of the combination of high-resolution readout and compact measuring range for fast, repeatable checks of external grooves and small features; the rotatable display and multifunction keys speed up setup and inspection. Order the instrument directly via Metav Werkzeuge or request advice from our consultants. Digital external probe 10–30 mm — compact digital measuring instrument with 0.005 mm resolution (Metav IndustryLine) The Digital external probe 10–30 mm is a compact digital dial gauge designed for rapid measurement of external grooves and small features in workshop and inspection settings. 0.005 mm resolution for fine measurements 10–30 mm compact measuring range Rotatable digital display with multi‑function keys Supplied in protective transport case Precision that reduces rework and speeds inspection With a display resolution of 0.005 mm, the instrument provides a noticeably finer readout than many conventional indicators, enabling closer tolerances to be monitored on small components. The specified accuracy of ±0.03 mm supports reliable pass/fail decisions during routine quality checks. Classified in the micro range for measuring devices (max. 10–100 mm), this tool is optimised for finemechanical tasks where short jaws and stiffness matter; it helps to minimise measurement uncertainty on narrow grooves and machined details. Designed for fast, ergonomic measurement of grooves and edges The device features a rotatable display with ON/OFF/SET, ABS/INC/UNIT, TOL-, DATA- and MODE-keys for efficient operation and quick mode changes without awkward repositioning. Rounded tips R0.75 are fitted to enable consistent contact in external grooves and narrow profiles, reducing slippage and local deformation. Supplied in a protective case for transport and safe storage, the instrument is robust enough for everyday shop-floor use while remaining easy to handle and set up. Practical fit for workshops, quality control and small-series production Built for frequent checks, the probe shortens inspection cycles and supports reproducible results when integrated into routine workflows. The compact footprint and approximately 0.9 kg mass make handling straightforward in bench or fixture measurements. Backed by Metav’s supply and quality filter in Emmerich, the product combines technical suitability with dependable logistics and after-sales clarity, helping small and medium enterprises to access specialist measuring equipment without complexity. Contact Metav Werkzeuge for a technical consultation on the digital probe and to arrange supply from Emmerich. Technical Data SKU: M209.162 GTIN: 4061905043857 Label: Digital-Außentaster 10 - 30 mm Ablesung 0,005 mm, mit Rundspitzen Category: Messuhren Facts Measuring range: 10–30 mm Resolution (readout): 0.005 mm Specified accuracy: ±0.03 mm Weight: 0.9 kg Tip radius: R0.75 Special features Digital display, rotatable, with ON/OFF/SET, ABS/INC/UNIT, TOL-, DATA-, MODE keys Intended for rapid measurement of external grooves and small features Supplied in a transport case for protection during shipping and storage Digital instrument (electronic readout) FAQ What measuring range does the instrument cover? The measuring range is 10–30 mm for the digital external probe (SKU M209.162), suited to small-feature and groove measurements. How fine is the readout and how accurate are the readings? Readout resolution is 0.005 mm and the specified accuracy is ±0.03 mm for this Metav IndustryLine digital probe. Are the measuring tips suitable for narrow grooves? Yes — the instrument is supplied with rounded measuring tips (R0.75) designed specifically to reach and measure external grooves consistently. Is the device ready for use on the shop floor? The probe is a compact, robust digital instrument supplied in a protective transport case, making it practical for regular workshop and inspection use. Which applications suit this instrument best? The device is aimed at precision workshop checks, small-series quality control and finemechanical tasks where compact range and high readout resolution matter; it is classified in the micro measuring range (max. 10–100 mm). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.6mm Internal Micrometer With Microcomputer Color 1.54" Touchscreen, Wireless+USB - Microtech Metrology
Take advantage of a compact, high‑resolution measuring solution that combines rapid data transfer, an integrated microcomputer and tactile control for reliable in‑line inspections. The combination of precise readout and seamless digital export supports consistent quality documentation and smooth production steps. Order the device directly via Metav Werkzeuge or consult our specialists for application advice. Microtech Metrology internal bore gauge — microcomputer control, Wireless + USB data output Microtech Metrology internal bore gauge is an electronic instrument tailored for precision measurement of cylindrical bores such as gun barrels, offering a measured focus on repeatability and digital workflow integration. Wireless + USB data export 1.54" colour touchscreen display Precision for 10.2–10.6 mm bores Integrated microcomputer control Repeatable internal inspection with industrial readout The instrument is built as a dedicated internal bore gauge that merges mechanical sensing with electronic processing to reduce operator variability and speed up quality checks. Its 0.0001 mm readout provides an exceptionally fine display step that supports confident decision making during acceptance testing and process control. The specified measurement range 10.2–10.6 mm makes the device particularly suited to narrow‑tolerance bores where consistent repeatability is essential; the compact measuring geometry helps to keep the sensing elements rigid and less prone to deflection under handling. Faster quality cycles through integrated data handling A built‑in microcomputer and modern user interface reduce manual transcription and accelerate reporting. The colour 1.54" touchscreen simplifies setting selection and immediate visual confirmation of results, while the Wireless + USB outputs enable direct export to inspection software or test records, shortening the time from measurement to document. This technical pairing is aimed at workshops and inspection bays that require rapid digital traceability without adding complex system integration work. Specialised design for barrels and similar bores Designed with barrel inspection in mind, the gauge accommodates the geometric and access constraints of rifled or smooth‑bore components and is specified for calibre 0.410 applications. The mechanical and electronic combination supports typical internal measurement modalities—inside diameter inspection, step and depth checks—so it is also useful for other small‑bore assemblies where a fine, repeatable result is required. Its form factor and controls were chosen to assist technicians carrying out series inspections and to reduce setup time between measurements. Workshop integration, documentation and partner reliability Metav’s distribution ensures the instrument is delivered with transparent handling and access to further product information. As a long‑standing precision partner, Metav provides a quality filter for the European market and a wide catalogue that helps consolidate procurement. For customers seeking a reliable measuring chain, the device links precise measurement capability with practical supply logistics and product support, creating an efficient inspection routine and dependable traceability. Contact Metav Werkzeuge today to request the full technical datasheet, confirm fit for specific barrel types or to place an enquiry about the Microtech Metrology internal bore gauge — Metav Werkzeuge, Parkring 45, Emmerich, is available to assist with specification matching and ordering. Technical Data Article number: 138070007 GTIN: 4061905045127 Manufacturer: Microtech Metrology Category: Precision measuring instruments Facts Measuring range: 10.2–10.6 mm Measuring range (inch): 0.410" Measuring range max: 10.6 mm Measuring depth: 760 Readout resolution: 0.0001 Digital display: Colour 1.54" touchscreen Data output: Wireless + USB Special features Integrated microcomputer control Digital device for internal bore inspection Calibre: 0.410 Intended application: barrel inspection and similar bores FAQ What bore sizes can this gauge measure? The instrument measures in the specified 10.2–10.6 mm range (0.410"), which makes it suitable for bores within that window and dedicated applications such as gun barrel inspection. What data output options are available? Measurement data can be exported via Wireless + USB, allowing the Microtech Metrology internal bore gauge to transfer results directly to PC systems or handheld loggers for traceable quality records. How fine is the readout and what does that mean in practice? The display offers a 0.0001 mm readout step, providing very fine visual resolution that supports tight‑tolerance checks; formal accuracy specifications can be provided on request for specific inspection protocols. Is the device suitable for calibre 0.410 barrels? Yes — the tool is specified with calibre 0.410 in mind and is configured to address the geometric constraints typical of such bores. Which types of internal measurements can be performed? The instrument is intended for precise internal diameter checks, step and depth evaluations in cylindrical bores typical of barrel inspection and other small‑bore components; it is designed to integrate with routine workshop inspection processes. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
100-250mm Gauge Pins Set, 4‑Piece For Internal Fine Gauging - Metav IndustryLine
Take advantage of a compact accessory that matches workshop standards: the set combines reliable compatibility with the 208.027 gauge, a dedicated 100–250 mm measuring span and the practical convenience of a four‑piece configuration. Order the set directly via Metav Werkzeuge or consult the team for specification matching and delivery. 4‑piece measuring pins for 208.027 (100–250 mm) — M8/7.2 mounting (Metav IndustryLine) The 4‑piece measuring pins for 208.027 (100–250 mm) form a compact accessory set designed to extend internal gauging capability across the standard workshop measuring range, offering secure M8/7.2 mounting for repeatable positioning. Set of four precision measuring pins Matched to 100–250 mm measuring range M8/7.2 mounting interface Low mass reduces probe load Precise alignment for internal measurement tasks The set of four measuring pins is designed to support accurate internal gauging across the 100–250 mm span, providing a simple way to adapt existing fixtures without extensive rework. The pins locate into the holder using an M8/7.2 interface, ensuring a consistent seating that reduces lateral play and improves measurement precision. With a nominal mass of 0.02 kg, the pins exert minimal additional load on the measuring head, so measurements remain stable and repeatable during routine checks. This compact accessory suits busy inspection benches where quick, reliable fitting is required and where small changes in probe load can otherwise introduce error. Compatibility and downtime reduction for production environments Designed as an accessory for the 208.027 family, the set supports rapid replacement and modular upgrades, helping to keep inspection plans on schedule. The set of four allows immediate swap‑outs when wear is detected, reducing machine downtime and avoiding lengthy recalibration cycles. Because the components are tailored to the instrument’s mounting standard, mechanical compatibility is assured and no ad‑hoc adapters are needed. That compatibility translates directly into operational efficiency: fewer interruptions, straightforward spare‑parts handling and a predictable stock item for routine maintenance. Measurable workflow benefits for workshop metrology Fitted within the Standard range for workshop gauges, this accessory improves throughput by simplifying setup for internal measurements. Repeatability is enhanced through consistent seating and matched geometry, which lowers variability from one probing cycle to the next. The low‑mass construction decreases dynamic influence on fine measuring systems, contributing to better short‑term stability and therefore clearer pass/fail decisions in quality control. Where inspection speed and traceable repeatability matter, the pins offer a pragmatic way to raise measurement confidence without large capital outlay. Practical handling, identification and traceability Each pack is supplied as a compact, four‑piece set with clear identification for inventory and procurement. The item is listed under SKU M208.027.BZ and carries GTIN 4054469146683 to support ERP and traceability workflows. The simple M8/7.2 mounting means fitment is straightforward for workshop technicians, and the small overall footprint makes the set easy to store as a labelled spare. For users aligning inspection equipment to standard gauges, this accessory is a logical, low‑risk addition that keeps measurement chains consistent and auditable. For tailored advice on integrating the Metav IndustryLine measuring pins set into existing gauges, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss compatibility, lead times and delivery options. Technical data Article number: M208.027.BZ GTIN: 4054469146683 ECLASS: 21170310 TARIC / customs code: 90179000 Category: Zubehör (accessory) Numbers Measurement range: 100–250 mm Weight: 0.02 kg Pieces per set: 4 Aufnahme / mounting: M8/7.2 Special features Accessory for model 208.027 Intended for internal measurement tasks Compact four‑piece configuration Suited to standard workshop measuring range (100–300 mm) FAQ What measuring range do these pins cover? The pins cover a 100–250 mm measuring span and are matched to internal gauging tasks within that range. Are these pins compatible with the 208.027 gauge? Yes — the 4‑piece measuring pins for 208.027 (100–250 mm) are designed specifically for compatibility with the 208.027 mounting and fit the instrument’s M8/7.2 interface. How many pins are included in one set? One set contains four individual measuring pins, supplied as a ready‑to‑use accessory pack under SKU M208.027.BZ. Is the item traceable for inventory systems? The product is identified by GTIN 4054469146683 and the SKU M208.027.BZ to support procurement and traceability. Can these pins affect probe load and measurement stability? The low mass (0.02 kg) of the pins minimises additional probe load, which helps maintain measurement stability and repeatability during short inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Depth Extension For Internal Fine Measurement Devices For Series 208.425/426/428/429 - Metav IndustryLine
Take advantage of the 1,000 mm extended reach and solid compatibility with the 208.425/426/428/429 series to measure deep internal bores without switching instruments. The robust design and 1.4 kg mass provide stable, repeatable readings for workshop metrology. Order this extension directly via Metav Werkzeuge or ask our consultants if needed. M208.420 Extension for Internal Fine Measuring Instrument — 1,000 mm (Metav IndustryLine) The M208.420 extension for internal fine measuring instruments increases measuring depth for dial indicators and similar internal metrology setups, enabling reliable assessment of deep bores and cavities in a workshop environment. 1,000 mm measuring depth extension Compatible with series 208.425/426/428/429 Robust construction for repeatable results Mass 1.4 kg for improved stability Reach deeper bores with workshop-ready measuring depth The 1,000 mm extension is designed to extend the measuring depth of internal fine measuring setups, making deeper bores and recessed features accessible without resorting to bespoke gauging fixtures. By adding length to the existing probe train, routine inspection tasks in maintenance, small-series production and toolroom work become more efficient. The extension is intended for use with dial indicators and precision internal gauges commonly found in metrology benches, translating extended reach into fewer instrument changes and faster set-ups. Stable readings through deliberate mass and compatibility With a mass of 1.4 kg, the extension adds useful inertia that reduces vibration and hand-induced oscillation during measurement, helping to secure repeatability in results. The component is matched to the mounting and interface geometry of the listed series, ensuring mechanical compatibility and minimal play at the coupling points. This stability supports consistent trial-to-trial comparisons and shorter measuring cycles, which is particularly advantageous where reproducible internal measurements are required for quality control. Integrates into existing metrology workflows with minimal effort The extension is delivered as a single, workshop-ready component that integrates directly into existing setups for internal measurement, avoiding the need for extensive retrofitting. Compatibility with the 208.425/426/428/429 series simplifies inventory management and tool selection, while the robust build addresses the practical demands of industrial use. For operations seeking to broaden their inspection envelope without investing in a new instrument suite, this extension offers a pragmatic, performance-focused option. For extended measuring depth and assured compatibility, request the M208.420 extension from Metav Werkzeuge or consult our specialists at Metav Werkzeuge for application advice. Technical data Article number: M208.420 GTIN: 4054469165462 Label: Verlängerung für Innen-Feinmessgerät, 1000 mm für Serien 208.425/426/428/429 Category: Dial indicators (Messuhren) Numbers / Core technical data Measuring depth: 1,000 mm Mass: 1.4 kg Tariff number: 90173000 Compatibility & special features Suitable for series 208.425, 208.426, 208.428, 208.429 Designed for internal measurement extension and deeper bore access Workshop-grade construction for repeatable readings FAQ Is the extension compatible with other dial indicator series? The M208.420 is specifically designed for mechanical compatibility with series 208.425/426/428/429; using it with other series may require adapters or checks for mechanical fit. What measurement improvement does the extension provide? By adding a 1,000 mm extension, the M208.420 enables inspection of deep internal bores and recessed features that would otherwise be inaccessible with standard probe lengths. How does the extension affect measurement stability? The additional mass (1.4 kg) and precise coupling reduce vibration and improve repeatability, supporting stable readings when used with compatible dial gauges. Is the extension suitable for shop-floor environments? Yes, the M208.420 is built for workshop use and is intended to integrate into existing metrology workflows for routine and production checks. Does the extension come calibrated? Calibration information is not provided with the product data; calibration status should be confirmed separately if a calibrated delivery is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Extension for Internal Fine Measuring Device For Series 208.424/208.427 - Metav IndustryLine
Take advantage of a 1000 mm depth extension that preserves measuring-system compatibility and keeps handling lightweight for efficient shop-floor measurements; the extension boosts range for internal inspections while remaining easy to fit and carry. Order the extension directly via Metav Werkzeuge or ask the consultants for matching advice. Extension for internal fine measuring instrument, 1000 mm (M208.421) — 1000 mm depth extension, Metav IndustryLine The Extension for internal fine measuring instrument, 1000 mm is a purpose-built depth extension designed to increase the measuring reach of compatible internal dial gauge systems for deeper bore and cavity inspections. 1000 mm measuring depth extension Compatible with series 208.424/208.427 Lightweight at 1.4 kg for easier handling Precision accessory for depth measurement Gain measurement range without sacrificing accuracy The 1000 mm rod extends the accessible depth for internal inspections, enabling measurements that would otherwise require multiple setups or specialised fixtures. Thanks to a focused design for dial-gauge systems, the extension keeps alignment stable over its length so that depth measurement remains reproducible. Integration with the parent gauge avoids complex adaptors; the result is a practical increase in capability that preserves the original instrument's repeatability and makes longer internal checks part of routine quality control rather than a special operation. Practical workshop benefits: simple fitting and ergonomic handling Fitted to series 208.424 and 208.427 instruments, the extension is kept lightweight (1.4 kg) to reduce operator fatigue during repeated use. The uncomplicated coupling concept shortens downtime between measurements and helps maintain throughput on production lines or during inspection rounds. For maintenance and setup, the accessory behaves like a modular component: it can be attached, verified and removed without specialised tools, which supports smooth processes and clear responsibility in busy workshops. Fit for quality processes and traceable inventory The extension is supplied with clear identifiers (SKU M208.421, GTIN) to support stock management and traceability in inspection protocols. Using a standardised extension for deeper measurements reduces the need for improvised solutions and helps keep measurement procedures auditable. Metav IndustryLine’s emphasis on consistent supply and an Emmerich-based quality filter supports reliable availability for industrial and workshop environments, reinforcing both operational efficiency and procurement certainty. Request tailored advice from Metav Werkzeuge to ensure the 1000 mm extension matches existing dial gauge setups, or secure the M208.421 directly through our Emmerich warehouse Technical data SKU: M208.421 GTIN: 4054469178905 ECLASS: 21170613 ETIM: EC002219 Tariff number: 90173000 Category path: Messgeräte > Messuhren Core technical data Measuring length: 1000 mm Weight: 1.4 kg Special features Compatible with series 208.424 / 208.427 Function: extension for measuring depth (internal) Intended for use with internal fine measuring instruments FAQ What is the primary purpose of this extension? The extension M208.421 is intended to increase the measuring depth of internal fine measuring instruments, allowing deeper bore and cavity inspections with compatible dial-gauge systems Which instrument series is this accessory compatible with? Compatibility is specified for series 208.424 and 208.427; the M208.421 is designed to couple directly to those internal fine measuring instruments Does the extension add significant weight during handling? With a weight of 1.4 kg the extension balances reach with manageable handling to reduce operator fatigue during repeated measurements Can the extension be used for repeatable quality inspections on the production line? Yes, the extension is designed to integrate into standard inspection workflows and, together with the parent instrument, supports reproducible depth measurements Is the accessory identifiable for inventory and documentation purposes? The M208.421 has a GTIN and SKU for clear identification and can be recorded in inspection and stock systems Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Internal Micrometer Carbide Measuring Faces 0.03mm Accuracy, 1000mm Depth - Microtech Metrology
Take advantage of the combination of a 400–1000 mm working range, ±0.03 mm accuracy and carbide measuring faces for dependable bore inspection of large components; order this instrument directly via Metav Werkzeuge or consult our specialists for application advice. Internal Precision Gauge — Dial bore gauge for 400–1000 mm with carbide measuring faces (Microtech Metrology) The Internal Precision Gauge is an analogue dial bore gauge designed for reproducible internal measurements of large bores in workshop and production environments. Large range 400–1000 mm Resolution 0.01 mm dial reading Carbide measuring faces for wear resistance Accuracy ±0.03 mm for consistent results Precise measurement for large bores that reduces rework This analogue instrument combines a broad measuring span with a fine reading, making it suitable where reproducibility and clear decision limits matter. The 400–1000 mm measurement window and a dial graduation of 0.01 mm allow rapid assessment of large internal diameters while keeping handling straightforward. With an indicated accuracy of ±0.03 mm, the device supports quality control steps that prevent costly rework and scrap by making out-of-tolerance conditions immediately visible. The analogue display gives immediate visual feedback, which speeds up serial inspection and supports lean production routines. Robust design and durable measuring faces for industrial use Durability is central for gauges that are used on shop floors. The instrument is fitted with carbide measuring faces, which resist wear during repeated contact and provide a stable measuring interface over prolonged use. The construction and hardened contact surfaces ensure unchanged geometry even after many measuring cycles, improving long-term repeatability. Because the depth capability is extended to 1000 mm, the gauge handles deep bores and long sleeves without compromising measurement integrity, so large assemblies can be checked with confidence. Easy integration into workshop routines and traceable quality control Handling and set‑up have been optimised for practical workshop use: the analogue dial indicator is intuitive to read and allows quick go/no‑go decisions. The instrument is classified for the large‑range internal measurement segment (suitable where profile stiffness and reach are critical), making it a pragmatic choice for maintenance, jigs and fixture checks, and incoming inspection of bulky parts. For procurement and process planning, Metav’s experience as a precision distributor provides an additional quality filter and supply reliability that supports uninterrupted production. Discuss specific applications with Metav Werkzeuge—our experts in Emmerich will advise on fitting this Microtech Metrology internal gauge into existing inspection routines and arrange prompt delivery; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 132900122 GTIN: 4061905454035 Manufacturer: Microtech Metrology Core specifications Measuring range: 400–1000 mm Measuring depth: 1000 mm Reading / Resolution: 0.01 mm Accuracy: ±0.03 mm Features and materials Analogue dial indicator Carbide measuring faces Category: Fine measuring instrument — internal gauge Image reference available FAQ What is the measurement range and suitability for large bores? The instrument covers 400–1000 mm and is designed specifically for large internal diameters where reach and profile rigidity are required. What resolution and accuracy does the gauge provide? The analogue dial shows a 0.01 mm graduation and the device offers an accuracy of ±0.03 mm, suitable for routine industrial inspection. Are the measuring faces wear-resistant? Yes — the gauge comes with carbide measuring faces, providing high wear resistance and stable contact geometry for repeated measurements. Is this instrument suitable for deep internal measurements? The design supports a measuring depth of 1000 mm, making it appropriate for deep bores, sleeves and long housings. Which manufacturer and article number identify this product? This internal gauge is supplied by Microtech Metrology; article number 132900122 and GTIN 4061905454035 identify the exact model. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Internal Micrometer Carbide Measuring Faces 440mm Depth 0.03mm Accuracy - Microtech Metrology
Take advantage of wear‑resistant carbide measuring faces, a 400–1000 mm measurement range and 0.03 mm analogue accuracy to secure reproducible internal measurements in large housings and bearings; order the instrument directly via Metav Werkzeuge or contact our consultants for application advice. Internal precision gauge — Internal measuring instrument with carbide measuring faces and 0.03 mm accuracy by Microtech Metrology The Internal precision gauge is a specialist analogue instrument for precise internal diameter and bore-depth inspections in production and maintenance environments Carbide measuring faces for long-term durability Wide measurement range 400–1000 mm Analogue accuracy 0.03 mm for precise readings Accurate measurement across large bores for reliable process control This analogue gauge offers a measurement range of 400–1000 mm combined with a measuring depth of 440 mm, enabling repeatable checks on large components such as housings, bearing seats and large pipe bores. The device’s 0.03 mm accuracy specifies the tolerance band expected during routine checks, while the scale reading of 0.01 mm allows clear interpretation of small deviations. These numerical characteristics make the instrument suitable for workshop quality control where measurable, comparable results are required and where documentation of dimensional conformity supports process stability and traceability. Durable contact surfaces and robust construction for long service life Equipped with carbide measuring faces, the gauge resists wear and maintains measurement integrity even under frequent use. Carbide tips reduce the risk of rounding or indentation on mating surfaces, which preserves both the component and the instrument. The analogue mechanism is designed for straightforward maintenance and longevity: fewer electronic parts mean an inherently robust tool for harsh shop-floor conditions. The combination of durability and stable mechanics reduces downtime and total cost of ownership in demanding production settings. Practical integration into workshop workflows and inspection routines The instrument’s form factor and analogue operation make it easy to incorporate into standard inspection jigs and measuring benches. The 440 mm measuring depth allows access to recessed features without additional adapters, shortening setup time for repetitive checks. Readings are immediate and intuitive, supporting quick go/no‑go decisions at the bench and efficient data capture for inspection reports. For processes requiring documented conformity, the gauge’s specifications permit clear pass/fail criteria to be defined and communicated to operators and quality staff. Contact Metav Werkzeuge today to discuss how the Microtech Metrology internal precision gauge can be integrated into inspection routines and to arrange supply from our Emmerich stock Technical data Article number: 132900100 GTIN: 4061905454028 ECLASS: 21170310 Manufacturer: Microtech Metrology Category: Feinmessgeräte / Precision measuring instruments Core specifications Measurement range: 400–1000 mm Measuring depth: 440 mm Accuracy: 0.03 mm Scale reading: 0.01 mm Analogue instrument Materials & features Carbide measuring faces Analog operation with vernier-style reading Intended for internal measurements of large components FAQ What is the maximum measuring range of this instrument? The internal precision gauge from Microtech Metrology covers a measuring range of 400–1000 mm. How precise is the gauge for routine inspections? The device delivers an accuracy of 0.03 mm with a scale reading resolution of 0.01 mm, suitable for production control and workshop quality checks. Are the contact tips suitable for frequent shop use? Yes, the instrument is fitted with carbide measuring faces, which are wear resistant and preserve both the tool and measured surfaces during repeated inspections. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Internal Micrometer Set With Carbide Faces, 0.01mm Resolution - Microtech Metrology
The combination of a 6–1000 mm measurement range, hardened carbide measuring faces and a repeatable ±0.03 mm accuracy delivers reliable internal measurements across small bores and large cavities; the analogue dial readout with 0.01 mm resolution supports fast decisions on the shop floor. Order the instrument set directly via Metav Werkzeuge or contact our consultants for specification matching and delivery from Emmerich. Microtech Metrology Internal bore gauge set – 6–1000 mm, carbide faces The Internal fine measuring instrument set provides a rugged, analogue solution for precise internal diameter checks across workshops and production environments, suitable for bores, cylinders and cavity inspection. Wide coverage 6–1000 mm range Carbide measuring faces for long life Analogue dial with 0.01 mm resolution Accurate internal checks that speed up quality decisions The set has been designed for reproducible internal measurements across a broad span of diameters. With an indicated accuracy of 0.03 mm and a dial resolution of 0.01 mm, the instrument provides clear, incremental readings that support rapid go/no‑go assessments during incoming inspection or inline sampling. The analogue display avoids software dependencies and enables immediate interpretation; this reduces cycle time at the inspection station while maintaining documented repeatability for part acceptance. Built for durability and repeatable contact quality Hardened carbide measuring faces give the contact geometry resistance to wear and maintain measurement integrity under frequent use. The mechanical construction prioritises stable contact and low hysteresis so results remain consistent across batches. For applications where surface hardness varies, the carbide tips help protect the sensing surface and extend service intervals, resulting in lower lifecycle cost compared with non‑hardened contacts. Practical set configuration for flexible workshop use Delivered as a set covering 6–1000 mm, the kit suits a wide mix of small to large bores without the need for multiple specialised tools. The instruments are analogue and mechanically intuitive, reducing training time for operators who require dependable, hands‑on gauges rather than networked metrology. The measured depth range of 60–2000 mm allows access to deep cavities and stepped bores, broadening the set’s applicability from maintenance tasks to production sampling. Clear benefits for production and inspection workflows Choosing this gauge set brings two principal advantages: swift, on‑the‑spot inspection decisions and durable contact performance for high‑volume cycles. The straightforward mechanical readout minimises interpretation errors and the robust tip material keeps calibration drift low over long intervals. For users seeking a pragmatic balance of range and resilience, the combination of wide measuring span and carbide tips offers a dependable inspection backbone without complex electronics. For a detailed technical match to an application or to secure supply from our Emmerich hub, contact Metav Werkzeuge to discuss the Microtech Metrology internal bore gauge set and delivery options. Technical data Article number: 132990105 GTIN: 4061905454158 Manufacturer: Microtech Metrology Facts Measuring range: 6–1000 mm Resolution: 0.01 mm Accuracy: ±0.03 mm Measuring depth: 60–2000 mm Special features Analogue dial readout Carbide measuring faces Supplied as a set FAQ What range does the set cover? The Microtech Metrology internal bore gauge set covers diameters from 6 to 1000 mm, offering flexible coverage for small bores up to larger cavities. How precise are the measurements with this instrument? The instrument provides a reading resolution of 0.01 mm and an overall accuracy of ±0.03 mm, enabling reliable tolerance checks for standard workshop inspection. Are the measuring faces durable for production use? Yes, the gauges feature hardened carbide measuring faces that resist wear and help maintain consistent contact geometry during repeated measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Internal Micrometer Set With Carbide Measuring Faces, Analog 0.001mm Resolution - Microtech Metrology
Take advantage of the combination of a wide 6–1000 mm measurement range, tungsten carbide measuring faces, and fine 0.012 mm accuracy for consistent internal dimension control on large components; order the set via Metav Werkzeuge or consult our specialists for application advice. Internal Dial Bore Gauge Set — 6–1000 mm, Carbide Faces by Microtech Metrology The Internal Dial Bore Gauge Set provides calibrated internal diameter measurement across a broad range for heavy‑duty workshop and toolroom applications Tungsten carbide measuring faces for wear resistance Wide measurement range 6–1000 mm in a single set High readout sensitivity 0.001 mm dial indicator Robust design for bore and deep‑reach measurements Precision that secures production tolerances The set combines a long measurement span with stable contact geometry to keep results reproducible even on large diameters. Fitted with tungsten carbide measuring faces, the gauges resist wear and maintain a reliable reference surface; this reduces rework and extends service life. The dial indicator provides a fine 0.001 mm reading step, while the instrument's stated accuracy of 0.012 mm supports dimensional control in machining, assembly and inspection workflows. The technical design focuses on measurable benefits: fewer scrap parts and predictable quality. Built for large bores and deep‑reach applications Classified in the "Mit Gross" category for its maximum range up to 1000 mm, the set is tailored for use with larger bearings, housings and cylindrical components common in heavy machining and plant engineering. The specified measuring depth of 60–2000 mm allows access to recessed features and stepped bores without makeshift extensions. Delivered as a complete set, the system reduces set‑up time and avoids repeated gauge swaps, enabling efficient measurement sequences on production floors and jigs. Practical reliability and ease of use in the workshop The construction emphasises ergonomic handling and simple assembly: extension rods and interchangeable anvils slot together for repeatable contact positioning, while the analogue dial makes small deviations immediately visible during manual checks. The carbide faces and robust mounting ensure drift‑resistant readings under regular use. For teams that value straightforward inspection routines, this solution offers a balance of precision and operational robustness that integrates well with standard QA processes. Contact Metav Werkzeuge for tailored advice on the Microtech Metrology internal bore gauge set (SKU 132990805) and to arrange a purchase or application consultation; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 132990805 GTIN: 4061905454080 eClass: 21170310 Manufacturer: Microtech Metrology Facts Measurement range: 6–1000 mm Measuring depth: 60–2000 mm Readout / resolution: 0.001 mm Accuracy: 0.012 mm Analogue instrument / dial indicator fitted Special features Tungsten carbide measuring faces Delivered as a set (Satz) Suitable for large‑format internal measurements Category: Mit Gross (500–1 000 mm) FAQ What measurement range does the set cover? The Microtech Metrology internal bore gauge set covers a continuous range from 6 mm up to 1000 mm, delivered as a complete set for extended bore measurement. Which readout and accuracy can be expected? The fitted dial indicator offers a fine 0.001 mm readout step and the instrument is specified with an accuracy of 0.012 mm for routine internal checks. Are the measuring faces durable for production use? Yes, the gauges are equipped with tungsten carbide measuring faces to resist wear and maintain stable contact surfaces under repetitive inspection cycles. Is the set suitable for deep or recessed bores? The set supports measuring depths from 60 mm to 2000 mm, enabling access to recessed features and long bores in large components. Does the delivery include multiple extension pieces? The set format includes the necessary interchangeable rods and anvils to assemble lengths across the 6–1000 mm measurement range for flexible application. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Internal Precision Gauge Set With Carbide Measuring Faces, 0.0001" Reading - Microtech Metrology
Take advantage of the 6–1,000 mm measuring range, carbide measuring faces and Wireless + USB data transfer to streamline large‑component internal measurement; order the set directly via Metav Werkzeuge or request a technical compatibility check from our consultants. Internal Fine Measuring Instrument set — carbide faces & Wireless/USB by Microtech Metrology The Internal Fine Measuring Instrument is a large‑range internal measuring set designed for precise measurement of internal diameters and bores in workshop and production environments. Large 6–1,000 mm measuring range Carbide measuring faces for wear resistance Colour 1.54" touchscreen readout Wireless and USB data transfer Large‑range precision where stiffness matters This set falls into the Large (500–1,000 mm) category, providing the reach required for sizeable internal diameters while maintaining the necessary profile stiffness for reproducible results. The 6–1,000 mm span is offered as a complete set, which reduces tool changeover and keeps measurement time to a minimum when verifying bores, housings or large bushings. The construction emphasises steady contact geometry so that readings remain stable across longer spans and repeated measurements. Modern readout and reliable data capture Equipped with a Colour 1.54" touchscreen and dual data interfaces, the instrument combines familiar tactile feedback with digital convenience. Wireless connectivity and USB output enable direct logging into inspection software or data collectors, which streamlines traceability and reduces transcription errors. The combination of analogue indication with a modern touchscreen provides both a reassuring mechanical reference and the efficiency of electronic data transfer for statistical process control. Durable contact surfaces and industrial repeatability The measuring faces are made from carbide, giving high wear resistance where frequent contact is expected; this preserves measurement integrity over prolonged use. With an stated accuracy of ±0.012 mm, the device sits within the range expected for workshop fine measuring instruments and supports consistent, repeatable measurements for quality control tasks. The unit’s design supports internal diameter checks across typical production loads without sacrificing service life. Set design for productive workshop use Delivered as a set covering 6–1,000 mm, the kit includes a range of extensions to reach different bore depths; the useful measuring depth spans 60–2,000 mm, allowing access to deep bores and stepped components. The set format reduces time lost swapping single gauges and keeps calibration status uniform across the measuring range. Combined analogue/digital readout and robust contacts make this a practical choice where throughput and reproducibility are priorities. Request a technical compatibility check or order the Microtech Metrology internal measuring set directly from Metav Werkzeuge in Emmerich for reliable, large‑range internal measurement. Technical data Article number: 132990705 GTIN: 4061905453847 Manufacturer: Microtech Metrology Numbers / Core technical data Measuring range: 6–1,000 mm Measuring depth: 60–2,000 mm Accuracy: ±0.012 mm Display: Colour 1.54" touchscreen Data output: Wireless + USB Special features Carbide measuring faces Analogue indication with digital touchscreen Delivered as a set covering full range Suitable for workshop and production inspection FAQ What measuring range does the set cover? The Microtech Metrology internal measuring set covers a measuring range of 6–1,000 mm and supports measuring depths from 60–2,000 mm (SKU 132990705). What accuracy is provided for internal measurements? Accuracy is specified as ±0.012 mm, positioning the instrument for reliable workshop‑level fine measurement tasks. How is measurement data transferred to a PC or system? The unit offers Wireless and USB data output and a Colour 1.54" touchscreen for local readout, simplifying integration with metrology software. Are the measuring faces durable for frequent use? Yes, the device uses carbide measuring faces designed for high wear resistance and long service life under repeated contact measurements. Which applications suit this large‑range internal measuring set? The set is intended for internal diameter measurements on housings, bushings and large machined components where a 6–1,000 mm range is required. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Internal Precision Measuring Instrument Carbide Measuring Faces, 0.001mm Vernier, 2000mm Depth - Microtech Metrology
Take advantage of the combination of hardmetal measuring faces, an extended measurement range 400–1,000 mm and fine resolution 0.001 mm for reliable, repeatable bore inspection. Order the internal gauge directly via Metav Werkzeuge or ask our consultants for application advice. Internal micrometer (inside measuring instrument) with hardmetal faces and dial indicator — Microtech Metrology The Internal micrometer is a precision instrument for measuring internal diameters and bores in medium to large components, designed for workshop and production use where reproducible results and wear resistance are required. Hardmetal measuring faces Measuring range 400–1,000 mm Resolution 0.001 mm dial reading Accuracy ±0.012 mm Precise large-component measurement made dependable The instrument is built for large-component measurement, classified for the 500–1,000 mm segment and therefore suited to inspection tasks in fixture and mould construction, hydraulic housings and large bore assemblies. Its hardmetal measuring faces give long-term wear resistance, which reduces rework and maintains accuracy over many inspection cycles. With a depth reach of 2,000 mm, the gauge covers extended bores and recessed features that would otherwise require multiple setups, improving throughput and lowering cycle time for quality control processes. Clear reading and stable results for routine inspection A fine dial indicator provides a resolution of 0.001 mm, enabling the detection of small deviations during set-up and run-off checks. The mechanical design prioritises stiffness and guidance over the measuring span to ensure repeatability: the combination of rigid guidance and robust contact faces translates into consistent readings and fewer out-of-tolerance finds. An indicated accuracy of ±0.012 mm positions the gauge for demanding workshop metrology where traceable, reproducible measurements are the baseline for downstream assembly and machining decisions. Designed for workshop integration and efficient handling The construction balances robustness with practical handling characteristics expected in production environments: a compact, guided measuring head for stability, and a clear dial for fast read-offs. The instrument suits inspection benches and portable measurement stations alike, helping to reduce setup time and the need for supplementary measuring jigs. When introduced into a calibrated inspection routine, the device contributes to predictable process control and fewer stoppages due to unclear measurement data. Contact Metav Werkzeuge for tailored advice on applying the Microtech Metrology internal micrometer in inspection routines or to request compatibility information for specific components Technical data Article number: 132900844 GTIN: 4061905453960 Manufacturer: Microtech Metrology Facts Measuring range: 400–1,000 mm Measuring depth: 2,000 mm Resolution (reading): 0.001 mm Accuracy: ±0.012 mm Analog display: yes Special features Hardmetal measuring faces Category: Fine measuring instruments ECLASS: 21170310 Dial indicator triggered functionality FAQ What measuring range does this gauge cover? The internal micrometer from Microtech Metrology covers a measuring range of 400–1,000 mm (SKU 132900844), making it suitable for medium to large bores. What precision can be expected from the instrument? The instrument offers a resolution of 0.001 mm on the dial and an indicated accuracy of ±0.012 mm, providing fine detection of dimensional deviations for workshop and production checks. Are the measuring faces suitable for heavy use? Yes, the gauge is fitted with hardmetal measuring faces, which provide enhanced wear resistance for repetitive contact on metallic surfaces and extend service intervals. How deep can measurements be performed? The gauge has a measuring depth of 2,000 mm, allowing inspection of deep bores and recessed features without additional extension tools. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
100mm Extension for IFMG 160–250 / 250–450mm, Ø18 Thread M14 - Metav IndustryLine
Take advantage of a compact 100 mm extension that extends IFMG measuring ranges with minimal added mass and a standard M14 mounting; order the accessory directly via Metav Werkzeuge or consult our specialists for compatibility advice. M208.026.V2 — 100 mm extension for IFMG gauges (M14 interface) — Metav IndustryLine The M208.026.V2 is a 100 mm extension designed to increase the reach of IFMG 160–250 mm and 250–450 mm fine measuring gauges, providing a lightweight accessory for workshop inspection and precision measuring tasks. 100 mm extension length M14 threaded interface for easy mounting Compatible with IFMG 160–250 / 250–450 mm Extremely lightweight at 0.02 kg Gain reach without compromising balance The 100 mm extension offers a practical method to extend the effective measuring range of IFMG fine measuring gauges while keeping the instrument well balanced. With a mass of just 0.02 kg, the accessory adds negligible inertia to the measuring head, which helps retain handling characteristics and reduces operator fatigue during repetitive checks. The short extension length is beneficial in confined setups where a full-length gauge would be impractical; it delivers additional reach for components or features that sit beyond the base instrument's nominal range while limiting the introduction of mechanical play. Precise interface and dependable compatibility Designed for a standard M14 interface (listed as M14/18), the extension couples directly with the specified IFMG gauge series and the models 208.025 and 208.026. This direct-fit approach removes the need for improvised adapters and simplifies configuration changes on the shop floor. The accessory is intended as a measuring-device add-on rather than a replacement part, ensuring that the parent instrument retains its factory calibration characteristics; integration remains straightforward thanks to the clearly defined mounting standard. Practical benefits for quality control workflows As an accessory labelled for measuring-device use, the extension supports faster set-ups and reduces the need to switch instruments when small reach adjustments are required. That operational flexibility translates into time savings during first-off inspections, repetitive sampling and jig-related verifications—making measurement tasks more efficient without demanding additional training. The compact form factor also aids storage and logistics: the lightweight component is simple to handle, transport and fit into existing tool kits for inspection teams. Robust choice from a trusted precision partner The extension is supplied as a dedicated accessory from the Metav IndustryLine range and matches the intended application for IFMG 160–250 and 250–450 mm gauges. Specification-driven design prioritises straightforward compatibility and workshop practicality over unnecessary complexity. For procurement and integration decisions, the accessory fits into standard inspection routines and supports consistent measurement workflows when paired with the matching IFMG instruments. Contact Metav Werkzeuge today to confirm suitability for specific IFMG gauges and secure the M208.026.V2 extension for improved reach in precision inspections Technical data Article number / SKU: M208.026.V2 GTIN: 4054469179025 Category: Zubehör (measuring instruments accessory) Facts Extension length: 100 mm Mass: 0.02 kg Mounting: M14/18 interface Tariff number: 90179000 Special features Compatible models: 208.025, 208.026 Intended for IFMG 160–250 mm and 250–450 mm ranges Accessory for fine measuring gauges Compact and lightweight design FAQ Which IFMG gauges are compatible with this extension? The extension is compatible with IFMG 160–250 mm and IFMG 250–450 mm gauge ranges and fits the models 208.025 and 208.026 as specified for the M208.026.V2 from Metav IndustryLine. What is the mounting interface and how is it specified? Mounting is by an M14 interface (noted as M14/18), providing a standardised threaded connection for direct fitting to the corresponding measuring heads. Will the extension affect the measuring performance? The M208.026.V2 is designed to add reach with minimal mass; any change to measurement uncertainty depends on the base instrument and the specific measuring task, but the short 100 mm length and low mass are intended to keep impact on performance small. Is the extension delivered calibrated? The extension is a mechanical accessory and is supplied without a separate calibration certificate; calibration applies to the measuring instrument itself rather than the extension. How much does the accessory weigh and does that matter for handling? The component weighs 0.02 kg, which is negligible for most handling and helps maintain the balance and ergonomics of the measuring setup. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
105-260mm Internal Fine Measuring Gauge With Retractable Probe, Color Touchscreen, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of ISO 17025 traceability, high-resolution readout and robust connectivity to speed inspection cycles and document results reliably; order this calibrated instrument from Metav Werkzeuge or contact our consultants for application advice. Internal Precision Gauge — Digital Internal Measuring Instrument by Microtech Metrology The Internal Precision Gauge is a digital instrument for precise internal diameter and bore-depth inspection, designed for workshop quality control and laboratory verifications within the standard measuring range. ISO 17025 calibration with certificate Wireless and USB data output 1.5" colour touchscreen display Retractable measuring head for bores Traceable accuracy for production-critical checks The instrument delivers traceable measurement results thanks to ISO 17025 calibration and an included calibration certificate, which supports formal quality records and audit trails. With a specified accuracy ±0.028 mm and a fine reading of 0.0001 mm, this device is positioned to reduce uncertainty in routine inspection tasks. The documented performance is particularly relevant where documented conformity and reproducibility are required for incoming inspection or first-article verification. Faster inspection through modern data handling Equipped with Wireless and USB data outputs and a 1.5" colour touchscreen, the gauge streamlines the documentation of measured values and improves throughput. Wireless transfer enables direct logging to statistical process control systems while USB provides a straightforward wired export option; both support common workflows in production environments. The intuitive display reduces operator interpretation time and minimises manual transcription errors, which contributes to measurable efficiency gains on the shop floor. Practical design that supports repeatable measurements Designed as a compact, workshop-capable instrument within the Standard range 105–260 mm, the device combines a retractable measuring head with a robust mechanism to reduce play during insertion and extraction from bores. This layout improves repeatability when performing internal diameter checks or depth measurements and makes the device suitable for quality control in metalworking, toolmaking and precision engineering. Delivery includes a support set to facilitate mounting and routine handling. Supplied ready for use and integrated into quality systems The gauge is supplied fully calibrated according to ISO 17025 and includes the calibration document, enabling immediate inclusion in accredited inspection routines. Measurable parameters such as the measuring range 105–260 mm, measuring depth 5000 mm and the digital 1.5" colour touchscreen are detailed for planners and technicians to verify compatibility with existing fixturing and data-logging setups. The manufacturer, Microtech Metrology, provides the industrial pedigree behind the instrument for users seeking a dependable metrology partner. For ISO 17025‑calibrated measurement integrity from Microtech Metrology, contact Metav Werkzeuge in Emmerich for tailored advice or to place an order via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 131260750 GTIN: 4061905044069 Manufacturer: Microtech Metrology Category: Precision measuring instruments Facts Measuring range: 105–260 mm Measuring depth: 5000 mm Reading: 0.0001 mm Accuracy: ±0.028 mm Display: 1.5" colour touchscreen Modules: 3 Special features Retractable measuring head Wireless and USB data output Digital instrument with colour display Delivery includes support set ISO 17025 calibration with certificate FAQ What measuring range does the instrument cover? The instrument covers a measuring range of 105–260 mm, making it suitable for standard workshop and machine‑tool bore inspections. Is the device supplied calibrated for audit use? Yes, the Microtech Metrology Internal Precision Gauge (SKU 131260750) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. How are measurements exported for SPC or documentation? Measured values can be transferred via Wireless or USB connections to common data‑logging or SPC systems for seamless documentation. Which applications suit this type of instrument best? The device is designed for internal diameter, bore depth and related inspection tasks in precision engineering, toolrooms and production quality control. What accessories are included on delivery? Delivery includes a practical support set to assist with mounting and handling during routine inspections. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
105-260mm Internal Micrometer With Retractable Measuring Head Color Touchscreen, ISO 17025 Calibration - Microtech Metrology
Take advantage of the precise combination of a 105–260 mm measuring range, fast Wireless + USB data transfer and included ISO 17025 calibration certificate for reliable, traceable internal measurements; order directly via Metav Werkzeuge or consult our specialists for application advice. Internal precision gauge — digital, retractable-head instrument by Microtech Metrology The Internal precision gauge provides a compact, digital solution for accurate internal measurements in workshop and production settings, designed for use where reach, repeatability and data traceability matter. Retractable measuring head for confined spaces Wireless and USB data output for traceability 1.5" colour touchscreen for clear readings Delivered with ISO 17025 calibration certificate Precision that fits everyday production needs This instrument covers a 105–260 mm measuring range, which places it squarely in the Standard range for machine and metalworking tasks. The device achieves an accuracy ±0.035 mm and a fine reading resolution of 0.0001 mm, giving a reliable balance between reach and stiffness for measurements on components such as housings, bushings and medium-sized workpieces. The numeric specifications translate directly into reduced rework and fewer rejected parts when used for inline inspections or manual quality checks. Rapid data capture for efficient workflows Equipped with Wireless + USB connectivity and a 1.5" colour touchscreen, the unit speeds up data collection and simplifies documentation. Measurement values can be exported without manual transcription, shortening lead times for quality reporting and lowering the risk of transcription errors. The instrument’s modular electronics (5 modules) support integration into existing data chains and make it straightforward to include measured results in production control systems for a measurable improvement in process control. Designed for internal and confined-space measurement tasks The gauge features a retractable measuring head, enabling access into narrow bores and recesses where conventional probes struggle, while the generous measuring depth: 10000 supports deeper internal profiles. The combination of a compact head and a digital readout lets operators perform stable, repeatable internal diameter and step measurements with fewer repositionings, increasing throughput on inspection benches and saving operator time across repetitive tasks. Laboratory-grade supply with documented traceability Delivered complete with a ISO 17025 calibration certificate and a complimentary support set, the instrument is ready for use in controlled quality environments and provides documented traceability for audit purposes. Manufactured by Microtech Metrology, the device blends workshop practicality with the assurance required by lab protocols: calibrated output, clear visual feedback and a robust data interface. This makes the unit suitable both as a standard shop-floor tool and as a documented measurement device for incoming inspection or final acceptance. Contact Metav Werkzeuge for tailored specification support or to reserve a calibrated Microtech Metrology internal gauge; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 131260795 GTIN: 4061905044083 Brand: Microtech Metrology SKU: 131260795 Facts Measuring range: 105–260 mm Accuracy: ±0.035 mm Reading resolution: 0.0001 mm Measuring depth: 10000 Modules: 5 Display: 1.5" colour touchscreen Special features Digital instrument (colour touchscreen) Data output: Wireless + USB Retractable measuring head Delivered with support set Supplied with ISO 17025 calibration certificate Suitable for standard machine and metalworking inspection tasks FAQ What measuring range does the instrument cover? The internal precision gauge offers a measuring range of 105–260 mm (Standard category), suitable for typical machine‑shop components and assembly parts; see SKU 131260795 for the exact configuration. Is a calibration certificate included with delivery? Yes — the device from Microtech Metrology is supplied with an ISO 17025 calibration certificate, ensuring laboratory‑grade traceability and documented conformity for audits. How are measured values exported from the unit? Measured values can be transferred via Wireless + USB interfaces; the instrument supports direct export to data collection systems to avoid manual entry and speed up reporting. Can the gauge access deep or narrow internal features? The retractable measuring head and a measuring depth of 10000 make the instrument suitable for confined bores and deeper internal features, improving access without special adapters. What display and user interface does the instrument use? Operation and readout are provided on a 1.5" colour touchscreen, offering clear numeric feedback and simple navigation for routine inspection tasks. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Fast, repeatable geometry checks in seconds
Caliper gauges (also referred to as precision calipers or quick-action gauges) are high-efficiency fine measuring instruments designed for precise geometry control in the production environment. Need to verify internal grooves, pipe wall thickness or small bores quickly? These tools deliver reliable results at sampling speed, making them ideal for series production, incoming goods inspection and workshop testing.
How they work and where they belong
The core of these devices is a spring-loaded lever system that applies a defined contact force, so measurements remain repeatable and independent of the operator’s feel. Caliper gauges capture hard-to-reach features — deep internal grooves, notches, freeform surfaces and thin walls — either mechanically or in digital form. Ergonomic one-handed operation allows the workpiece to stay in the machine or on the test table while checks are performed, reducing handling and downtime.
Practical advantages that improve throughput
- Consistent repeatability due to defined contact force, lowering measurement scatter.
- Rapid sampling: geometry checks are performed in the time of a few seconds, reducing cycle times.
- Flexible contact options such as ball, blade or disc contacts, matching different workpiece geometries.
- Choice of robust analog models or digital units with Go/NoGo tolerance indication and interfaces for direct integration into digital quality assurance.
- Ergonomic design that shortens set-up and inspection times, increasing shop-floor productivity.
Metav: a reliable precision partner for industry
Metav combines decades of metrology experience with a broad offering from Emmerich, acting as a quality filter for the European market. With more than 48,000 customers and over 250,000 products, Metav supplies a comprehensive selection of caliper gauges and accessories, helping purchasing managers reduce supplier complexity while securing reliable supply and technical competence.
Summary
Caliper gauges — precision calipers and quick-action gauges — provide fast, repeatable and operator-independent measurements for demanding industrial inspection tasks, delivering measurable gains in throughput and quality control.
FAQ
What makes caliper gauges suitable for deep internal measurements?
The spring-loaded lever system in caliper gauges ensures a defined contact force while specialised stylus geometries (ball, blade, disc) reach deep grooves and notches, enabling precise capture of internal features.
Can digital caliper gauges be integrated into existing quality systems?
Yes. Digital caliper gauges often include tolerance indication (Go/NoGo) and data interfaces, allowing direct connection to digital quality assurance systems for automated logging and analysis.
Which contact form should I choose for thin-walled parts?
For thin or delicate walls, disc or ball contacts minimise local deformation; Metav’s product range lists the available contact geometries so you can match the caliper gauge to the application.
How do caliper gauges maintain operator-independent repeatability?
Defined contact force from the spring-loaded lever system removes variability caused by hand pressure, so caliper gauges deliver consistent measurements across different operators and cycles.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com