Limit plug gauge — FAQ and category guide
Explore limit plug gauges for quick, accurate bore size checks. Covers twist drill compatibility, materials, and care tips. Choose the right gauge to boost inspection speed with reliable, user-friendly tools.
19mm Limit Go Gauge Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance on the good side for reliable, repeatable gauging in production and inspection. Order the Filetta limit gauge pin directly via Metav Werkzeuge or ask our consultants if additional technical clarification is required. Filetta Grenzlehrdorne MS911.223 – limit gauge pin, hardened steel, DIN 7162 a Filetta limit gauge pin designed for dimensional control and go/no-go gauging in workshops and inspection stations Hardened steel construction Conforms to DIN 7162 19 mm nominal diameter Wear allowance on the good side Precision and durability for routine gauging The MS911.223 is manufactured from hardened steel, a choice that secures dimensional stability and high wear resistance during frequent insertion and comparison checks. Compliance with DIN 7162 ensures the component meets recognised geometric and tolerance specifications for limit gauges, while the built‑in wear allowance on the good side prolongs service life by compensating for gradual surface loss. Together these attributes reduce replacement frequency and maintain repeatable pass/fail decisions on the production line. Designed for efficient production quality control This type of limit gauge pin is optimised for fast go/no‑go checks and routine inspection tasks where clear binary results speed up decision‑making. The compact form and standardised diameter facilitate interchange with common fixtures and gauge holders; in practice this supports lean inspection workflows and minimises downtime. Where rapid throughput and consistent judging of fit are required, the simple, robust design translates directly into measurable operational efficiency. Clear specification and dependable sourcing for procurement Specification is straightforward: nominal 19 mm diameter, hardened steel material and adherence to DIN 7162, referenced under SKU MS911.223 for ordering and inventory. For buyers seeking traceability and repeatable procurement, these concise data points simplify purchasing and ensure the gauge integrates seamlessly with existing control plans. Metav’s distribution and quality filtering further support reliable delivery into workshops and inspection rooms across Europe. For DIN 7162-compliant gauging, request the Filetta MS911.223 via Metav Werkzeuge or contact our technical advisers at info@metav-werkzeuge.com / +49 2822 7131930 to confirm fitment and application specifics. Technical Data Article number: MS911.223 Material: hardened steel Standard: DIN 7162 Nominal diameter: 19 mm Facts Product type: limit gauge pin Manufacturer: Filetta Application: dimensional control / go/no-go checks Special features Wear allowance on the good side Robust, compact design Suitable for fixture and holder systems FAQ What is the primary use of this limit gauge pin? The Filetta limit gauge pin MS911.223 is intended for quick go/no‑go checks and dimensional control of mating bores and components in production and inspection environments. Which material is used and how durable is it? Manufactured from hardened steel, the Filetta MS911.223 offers enhanced wear resistance and dimensional stability for repeated gauging operations. What does the wear allowance on the good side mean? The wear allowance on the good side allows the Filetta limit gauge pin to tolerate small surface losses over time while preserving the GO condition, extending the serviceable life of the gauge. Does this gauge meet any standards? Yes, the Filetta limit gauge pin MS911.223 is produced in accordance with DIN 7162, ensuring compatibility with recognised gauging practices and tolerancing. How should this item be referenced when ordering? Use SKU MS911.223 and the description Filetta limit gauge pin, 19 mm, hardened steel, DIN 7162 for accurate ordering and inventory tracking. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
2 mm Limit Gauge Pin Wear Measurement Side, Hardened Steel, DIN 7162 - Filetta
Take advantage of precise, repeatable inspection in a compact format: robust hardened steel construction and compliance with DIN 7162 ensure reliable go/no‑go assessment and long service life; order the limit plug gauge directly via Metav Werkzeuge or request detailed specification support from our consultants. Limit plug gauge G7 (MS911.160) – hardened steel, DIN 7162 — Filetta Limit plug gauge G7 (MS911.160) for quick verification of bore tolerances in routine inspection and incoming goods control Hardened steel construction for longevity DIN 7162 compliant inspection gauge Wear allowance on the good side for service life Precision gauge pin, 2 mm nominal size Repeatable inspection that reduces rework and inspection time The limit plug gauge offers a straightforward method for verifying bore tolerances without complex measurement setups. Manufactured from hardened steel, the gauge provides consistent contact geometry and wear resistance; this translates into repeatable pass/fail checks at points of inspection, reducing the time spent on detailed measuring instruments and lowering the risk of unnecessary rework. Compliance with DIN 7162 ensures that acceptance criteria are clear and comparable across suppliers, supporting efficient quality control in production and incoming goods. Durable design with a built‑in allowance for wear A defining characteristic is the wear allowance on the good side, which compensates for gradual material loss during repeated use and maintains the defined acceptance margin for longer. The hardened substrate keeps the contact faces stable, so the gauge preserves its functional geometry under regular workshop conditions. For inspection routines where robustness and predictable service intervals matter, this design reduces downtime and the frequency of replacements, providing a reliable tool for standardised checks. Practical integration into workshop and inspection routines Designed as a simple go/no‑go instrument, the gauge is ideal for rapid checks on components during assembly, jig setting and final inspection. The compact format and clear acceptance principle make it suitable for bench use and for operators with basic training in metrology. Combined with a documented standard such as DIN 7162, the tool supports traceable inspection protocols and straightforward documentation in quality records, assisting both production staff and quality engineers in maintaining batch conformity. Discuss specification details with Metav Werkzeuge or request a technical comparison from our Emmerich hub — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS911.160 Material: hardened steel Standard: DIN 7162 Nominal size: 2 mm Special feature: wear allowance on the good side Facts Product type: limit plug gauge Brand: Filetta SKU: MS911.160 Special features Robust contact faces Suitable for go/no‑go checks Purpose: bore tolerance verification Compact inspection tool for workshop use FAQ What is the primary use of this limit plug gauge? The limit plug gauge MS911.160 by Filetta is used for rapid go/no‑go verification of internal bore tolerances during incoming inspection and production control. What material is the gauge made from and why does that matter? The gauge is manufactured from hardened steel; this gives stable contact geometry and wear resistance, maintaining reliable inspection performance over repeated use. How does the wear allowance affect inspection intervals? The integrated wear allowance on the good side increases the effective service life by compensating for minor material loss, so maintenance and replacement intervals can be extended while preserving acceptance criteria. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
2 mm Limit Gauge Plug Gauge Wear Allowance Marking, Hardened Steel DIN 7162 - Filetta
Take advantage of a robust combination of hardened steel construction, DIN 7162 conformity and a specified wear allowance on the good side to ensure stable go/no-go inspection results; order the gauge directly via Metav Werkzeuge or consult our advisors for application support. Limit plug gauge (go/no-go) – hardened steel, DIN 7162 | Filetta The limit plug gauge is a hardened steel go/no-go instrument designed for rapid inspection of bore diameters in mechanical production and quality control environments. Hardened steel construction Conforms to DIN 7162 standard Wear allowance on 'good' side Suitable for go/no-go bore checks Reliable inspection that stabilises quality control A compact plug gauge built from hardened steel, manufactured to DIN 7162, offers a straightforward and verifiable check of bore conformity. The compact design supports quick in-process inspection, enabling repetitive pass/fail assessments with minimal setup. By using a dedicated limit gauge rather than improvised measuring methods, production lines gain predictable throughput and a reduced risk of downstream rejects, translating into measurable time savings during routine quality checks. Design detail that extends service life and repeatability The integrated wear allowance on the 'good' side compensates for gradual material loss at the contact surfaces so the "Go" dimension remains within tolerance for longer service intervals. This allowance is a pragmatic engineering measure: it preserves the reference condition of the gauge under regular use and simplifies maintenance planning. In practice, the clear distinction between the Go and No‑Go ends accelerates operator decisions and reduces subjective judgement during inspections. Robust build for workshop and production use Constructed from hardened steel and intended as a repeatable limit reference, this plug gauge is suitable for workshop inspection benches and production stop‑checks alike. The straightforward go/no-go principle means checks are fast, training effort is low and measurement routines are easy to embed into quality plans. Supplied as a standard plug gauge by Filetta, the item is particularly suited to machine shops and inspection departments that prioritise durable, standard‑compliant instruments for daily use. For tailored advice and supply from Metav Werkzeuge, order the Filetta limit plug gauge MS911.202 or request application guidance by emailing info@metav-werkzeuge.com or calling +49 2822 7131930 Technical data Article number: MS911.202 Material: hardened steel Standard: DIN 7162 Special feature: wear allowance on 'good' side Nominal size: 2 mm Core data Nominal size: 2 mm Special features Go/no-go functionality for bore inspection Hardened steel for extended durability Conforms to DIN 7162 specification Category: plug gauge / limit gauge Brand: Filetta FAQ What is the primary use of this plug gauge? The limit plug gauge is used for rapid go/no-go checks of bore diameters to confirm whether components meet the specified tolerance. How does the wear allowance affect inspection intervals? The wear allowance on the 'good' side extends the usable life of the gauge by compensating for contact surface wear, delaying the point at which recalibration or replacement is required. Which materials is the gauge made from? The gauge is manufactured from hardened steel, selected to provide resistance to wear and stable reference dimensions under routine workshop use. Is the gauge suitable for production floor use? Yes. The go/no-go design and rugged construction make this plug gauge appropriate for frequent checks on the production floor and at inspection stations. What identifier should be quoted when ordering or requesting spare parts? Please quote the article number MS911.202 and the Filetta brand designation when placing orders or enquiring about replacements. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
2.5 mm Limit Gauge Plug, Wear Allowance On Go Side, DIN 7162 - Filetta
Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance to ensure dependable go/no-go checks in serial inspection. Order the Filetta limit gauge pin directly via Metav Werkzeuge or request specialist advice for integration into existing inspection routines. Filetta Limit Gauge Pin — hardened steel, DIN 7162 Filetta Limit Gauge Pin designed for pass/fail checking of bores and inspection fixtures in industrial metrology Hardened steel construction to DIN 7162 Precision diameter 2.5 mm Wear allowance on the good side Compatible with go/no-go checking routines Reliable pass/fail checking for production control The limit gauge pin delivers a compact, unambiguous check for bore conformity using a simple go/no-go principle, minimising decision time on the shop floor. Manufactured to DIN 7162, the pin provides a clearly defined acceptance limit that supports reproducible inspections and consistent quality gates. The 2.5 mm diameter is specified to industry tolerances, enabling rapid visual and tactile confirmation without complex set‑ups. This direct verification method reduces downstream rework by catching out-of-tolerance parts at the earliest stage. Durability that reduces downtime and maintenance Constructed from hardened steel, the gauge pin resists wear in continuous use and preserves the inspection boundary over many cycles. The integrated wear allowance on the good side prolongs service life by permitting controlled dressing or replacement procedures while maintaining measurement integrity. Fewer replacements and predictable maintenance intervals lead to improved uptime in production lines and lower total cost of ownership. The robust material choice also supports use in regulated environments where repeatability matters. Simple integration into quality workflows and fixtures The pin is suited for fixtures, plug gauges and measuring rigs where straightforward verification is required. Its compact profile and standardised specification make stock management and fixture design straightforward, helping to keep inspection routines efficient. Clear identification (SKU MS911.161) and adherence to established norms aid traceability in quality records and simplify audits. The component is ideal for workshops and inspection stations seeking a pragmatic, standards-based tool to support routine quality control. Contact Metav Werkzeuge for tailored advice and to source the Filetta limit gauge pin (SKU MS911.161) directly from Emmerich — expert support for specification and delivery is available. Technical Data Article number: MS911.161 Manufacturer: Filetta Type: Limit gauge pin Diameter: 2.5 mm Standard: DIN 7162 Material: hardened steel Special note: wear allowance on the good side Facts Diameter: 2.5 mm Standard: DIN 7162 SKU: MS911.161 Special features Hardened steel construction Wear allowance of the good side Intended for go/no-go checking and plug gauge applications Category: gauges / measuring pins FAQ What material is the gauge pin made from? The Filetta limit gauge pin is manufactured from hardened steel, ensuring wear resistance and stable inspection boundaries (SKU MS911.161). Which standard applies to this gauge pin? Manufactured to DIN 7162, the component fulfils established requirements for limit gauges and supports clear pass/fail decisions. What does the wear allowance mean in practical terms? The wear allowance on the good side allows controlled use and maintenance so the gauge retains its acceptance limit for longer in serial inspections. Can this pin be used in fixture-based inspections? Yes, the pin is suitable for fixture and plug gauge applications where a defined go/no-go limit is required for bore checks. How is the size specified? The pin is specified with a diameter of 2.5 mm and supplied under SKU MS911.161 for unambiguous ordering and traceability. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
2.5mm Limit Go Gauge With Wear Allowance, Hardened Steel DIN 7162 - Filetta
Take advantage of the combination of DIN 7162 conformity, hardened-steel durability and exact 2.5 mm tolerance control for reliable go/no‑go checking in batch inspection. Order the Filetta limit gauge pins directly via Metav Werkzeuge or consult our specialists for batch supply and enquiries. Grenzlehrdorne — limit gauge pin, 2.5 mm, hardened steel (Filetta) A Grenzlehrdorn by Filetta designed for precision go/no‑go verification and wear‑compensated accept/reject checks in production and inspection environments. 2.5 mm diameter, high repeatability Hardened steel construction for long life Conforms to DIN 7162 standard Wear allowance on the good side Consistent go/no‑go control to speed up inspection The Filetta limit gauge pin offers a compact solution for rapid acceptance testing where dimensional conformity must be checked repeatedly. Manufactured from hardened steel, the pin retains its geometry under frequent use, reducing downtime caused by damaged or worn gauges. The specification to DIN 7162 ensures compatibility with established inspection procedures and simplifies documentation within quality systems. The compact form factor and clear acceptance boundary make the item particularly suitable for small‑part assemblies where a fast pass/fail decision avoids lengthy measuring operations. Durable construction that reduces recalibration frequency Robust material selection and heat treatment give the gauge pin a service life that keeps maintenance intervals low. The hardened surface resists deformation, helping maintain the defined tolerance of 2.5 mm over many cycles. In addition, the built‑in wear allowance on the good side provides an engineered margin so that the gauge indicates wear before part acceptance is compromised. This design choice translates into lower lifecycle costs and fewer process interruptions, supporting steady production throughput and reliable quality control. Integrates with workshop routines and quality documentation Designed as a practical shop tool, the limit gauge pin supports streamlined inspection workflows and clear go/no‑go decisions at the point of assembly or incoming inspection. The simple physical check complements dimensional measurement equipment and is ideal for quick checks on batches or random samples. The product is supplied under the Filetta brand and can be adopted easily into existing inspection plans; traceability is maintained through the SKU MS911.203 for ordering and stock control. The result is a pragmatic balance between measurement certainty and operational efficiency. Contact Metav Werkzeuge for Filetta limit gauge pins (SKU MS911.203) to arrange a batch supply or technical briefing near Emmerich — our specialists will advise on quantities and integration into inspection plans. Technical Data Article number: MS911.203 Product name: Grenzlehrdorne Manufacturer: Filetta Material: gehärterter Stahl Standard: DIN 7162 Facts Diameter: 2.5 mm SKU: MS911.203 Special features Abnutzungsaufmaß der Gutseite (wear allowance on the good side) Intended for go/no‑go verification and pin gauge checks Category: Gauge pins / measuring pins FAQ What is the primary use of these limit gauge pins? The Filetta Grenzlehrdorne are intended for rapid go/no‑go checks and dimensional acceptance testing in production and inspection, providing a quick physical decision on part conformity. Is the material suitable for high‑frequency shop use? Yes; the pins are made from hardened steel, which offers resistance to wear and deformation under frequent use, ensuring consistent pass/fail performance. Does this pin comply with recognised standards? The limit gauge pin conforms to DIN 7162, making it suitable for integration into standardised inspection procedures and quality documentation. How does the wear allowance affect inspection results? The built‑in wear allowance on the good side gives an engineered margin that signals wear before a pin accepts out‑of‑tolerance parts, thereby safeguarding process quality. How can this item be ordered or specified for stock? Order by SKU MS911.203 (Filetta) via Metav Werkzeuge for reliable supply and support with integration into inspection routines. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
20 mm Limit Gauge Pin Wear Measurement Face Reference, Hardened Steel, DIN 7162 - Filetta
Take advantage of DIN 7162 conformity, hardened steel construction and the integrated wear allowance on the go side for dependable bore verification. Order this limit plug gauge directly via Metav Werkzeuge or contact our consultants for application advice. Limit plug gauge G7 – 20 mm, hardened steel (DIN 7162) by Filetta A limit plug gauge G7 designed for rapid go/no-go checks of cylindrical bores in production and inspection environments Hardened steel for long service life Manufactured to DIN 7162 standard Wear allowance on the go side Suitable for bore verification and QC Reliable measurements through recognised standards The gauge is manufactured to DIN 7162, which ensures consistent dimensions and interchangeability across inspection routines. For a nominal size of 20 mm, the plug gauge provides an immediate go/no-go decision, eliminating lengthy measurement evaluation processes. This standard-led approach supports efficient quality control, reduces scrap rates and shortens inspection cycles by delivering clear, repeatable outcomes at every station. Durable construction that reduces downtime Made from hardened steel, the instrument tolerates repeated use on the shop floor while maintaining dimensional stability. The incorporated wear allowance on the go side compensates for gradual material loss during routine checking, extending the service life before any rework or replacement becomes necessary. This pragmatic design reduces unplanned stoppages and lowers total cost of ownership by keeping maintenance intervals predictable. Practical integration for workshop and production use Sized for common bore checks, the plug gauge is ideal for quick verification during assembly, final inspection or incoming goods control. Its straightforward go/no-go functionality accelerates throughput without requiring complex measuring equipment or extensive operator training. The robust design and adherence to DIN 7162 make it suitable for use in machine shops, tool rooms and quality laboratories where rapid, trustworthy pass/fail decisions are required. Reference: model MS911.182 for ordering and stock enquiries. Contact Metav Werkzeuge for expert advice on integrating Filetta limit plug gauges (DIN 7162) into existing inspection routines and to secure reliable supply from our Emmerich warehouse Technical Data Article number: MS911.182 Material: hardened steel Standard: DIN 7162 Size: 20 mm Facts Diameter: 20 mm Special features Wear allowance on the go side Designed for go/no-go checks Robust hardened-steel construction FAQ What is the primary use of this limit plug gauge? This limit plug gauge is intended for fast go/no-go verification of cylindrical bores, providing a clear pass/fail result for production and inspection tasks. What material is the gauge made from and why does it matter? The gauge is produced from hardened steel, which ensures wear resistance and dimensional stability under frequent use, supporting reliable long-term measurements. Which standard does the product comply with? Manufactured to DIN 7162, the gauge meets recognised dimensional and manufacturing criteria for plug gauges used in industrial quality control. How does the wear allowance affect inspection intervals? The wear allowance on the go side compensates for gradual abrasion, extending useful life and allowing longer intervals between gauge replacement or rework; the item is listed as MS911.182 for ordering and inventory reference. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
3 mm Limit Gauge Plug Gauge Wear Allowance, DIN 7162 - Filetta
Take advantage of a compact, standardised gauge that combines hardened steel construction with conformity to DIN 7162 for dependable go/no‑go verification; the built‑in wear allowance on the good side reduces rework and prolongs service intervals. Order the limit plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Grenzlehrdorne — limit plug gauge in hardened steel, DIN 7162 (Filetta) The Grenzlehrdorne is a precision limit plug gauge designed for efficient go/no‑go checks and rapid acceptance testing across workshop and production environments. Hardened steel construction Conforms to DIN 7162 Wear allowance on good side Repeatable acceptance checks that speed up inspection A limit plug gauge of this design provides an immediate pass/fail decision, making go/no‑go verification both fast and unambiguous. Conformity with DIN 7162 guarantees that gauges are produced to a recognised industrial standard, which simplifies incoming inspection routines and reduces interpretation effort. By relying on a standardised gauge, throughput is improved and measurement uncertainty from subjective assessment is minimised, supporting a more efficient quality workflow. Durable construction that lowers lifecycle costs Manufactured from hardened steel, the gauge resists wear under repeated contact and maintains its dimensional stability over many cycles. The specified wear allowance on the good side compensates for gradual surface degradation, preserving functional fit and reducing the frequency of replacements. Fewer gauge changes mean less downtime and lower total cost of ownership for routine inspection tasks, especially in high‑volume production or repetitive quality checks. Practical fit for workshop and production use The compact limit plug gauge suits routine acceptance tasks and bench checks where quick decisions are required. Traceability is straightforward during audits when the article identifier MS911.162 is used in documentation, and the robust finish simplifies handling in busy environments. The gauge is particularly appropriate for verifying internal diameters where a simple, repeatable standard is preferable to time‑consuming measurement setups, thus keeping operations lean and reliable. Contact Metav Werkzeuge for tailored advice and supply of Filetta hardened‑steel limit plug gauges and to discuss the best gauge strategy for production or inspection needs Technical Data Article number: MS911.162 Material: hardened steel Standard: DIN 7162 Feature: wear allowance on good side Product type: limit plug gauge Numbers / Core technical data Nominal size: 3 mm Special features Hardened steel construction Design for go/no‑go verification Conformity to DIN 7162 Built‑in wear allowance on the good side FAQ What is the primary use of this limit plug gauge? The limit plug gauge from Filetta is intended for quick go/no‑go checks and acceptance testing of internal diameters where an unequivocal pass/fail result is required. Which standard does the gauge comply with? Compliance with DIN 7162 ensures the gauge meets established industrial production and inspection criteria. What material is used for the gauge and why does it matter? The gauge is made from hardened steel, which provides wear resistance and dimensional stability under repetitive use. How does the wear allowance affect service life? The wear allowance on the good side prolongs the functional life by compensating for gradual surface wear, maintaining fit for longer before requalification or replacement is required. How can the gauge be identified in documentation? Use the article number MS911.162 for traceability in inspection records and procurement lists. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
3 mm Limit Plug Gauge With Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Hardened steel construction, conformity with DIN 7162 and a deliberate wear allowance on the go side provide fast, repeatable pass/fail decisions for small-bore inspection. Combine these attributes with Metav Werkzeuge’s supply reliability to keep inspection gates closed and production flowing. Order the gauge directly via Metav Werkzeuge or ask our consultants if needed. Plug limit gauge — hardened steel, DIN 7162 (Filetta) A plug limit gauge for rapid go/no-go testing of small bores, designed to meet workshop and production inspection requirements Hardened steel for durable measurements Conforms to DIN 7162 gauge standard Wear allowance on the go side for extended service life Rapid conformity checks that streamline inspection The plug limit gauge is a compact instrument tailored for immediate acceptance testing: a straightforward go/no-go decision eliminates prolonged measurement routines and reduces throughput bottlenecks. Constructed from hardened steel, the gauge resists deformation and preserves dimensional integrity under frequent use, which increases repeatability and reduces downtime caused by ambiguous results. Conformity to DIN 7162 ensures that the gauge integrates into standardised inspection plans and supports consistent quality control documentation. Durable design that suits busy workshops Made of hardened steel and supplied with a factory-specified wear allowance on the go side, the gauge delivers long service intervals even under continuous use. The tool’s compact geometry is optimised for small-bore verification and fits into common inspection benches and gauge fixtures. This simple construction reduces maintenance effort: when the go end begins to show wear beyond the allowance, replacement or regrinding can be scheduled without unexpected production stops, preserving measurement certainty and operational uptime. Practical benefits for quality workflows Specified as a plug-type limit gauge, the tool provides clear, binary results that accelerate decision-making in incoming inspection and production control. Reduced measurement time lowers labour costs and minimises the risk of release of non-conforming parts. The item is listed under SKU MS911.204 and is suited for routine checks where standardised acceptance criteria are enforced. For procurement and integration into measurement plans, Metav Werkzeuge offers product guidance and consistent European distribution that simplifies stocking and traceability. Discuss batch supply, compatibility with existing gauge sets or integration into inspection protocols with Metav Werkzeuge for Filetta plug limit gauges Technical data Article number: MS911.204 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Special feature: wear allowance on the go side Numbers / Core technical data Nominal size: 3 mm Special features / Versions Gauge type: plug limit gauge (go/no-go) Intended application: small-bore inspection and acceptance testing Category: gauges / measuring pins FAQ What is a plug limit gauge used for? A plug limit gauge provides a simple go/no-go check for bore diameters; the Filetta plug limit gauge (SKU MS911.204) is intended for quick acceptance testing of small bores in production and inspection. What material is the gauge made from? The Filetta plug limit gauge is manufactured from hardened steel to ensure dimensional stability and long-term durability under regular use. What does the wear allowance on the go side mean? The wear allowance indicates a designed service margin on the go end so that measured wear can be tolerated without immediate rejection; this extends usable life while maintaining reliable pass/fail decisions. Which standard does the gauge conform to? The gauge complies with DIN 7162, making it suitable for standardised inspection routines and integration into quality control documentation. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
3.5 mm Limit Plug Gauge With Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Combining DIN 7162 conformity, hardened steel construction and a wear allowance on the Go side yields a durable checking tool for repeatable bore inspections; order the gauge directly via Metav Werkzeuge or consult our advisers for application guidance. Limit plug gauge G7 — 3.5 mm, hardened steel (Filetta) Limit plug gauge G7 is a hardened-steel go/no-go gauge designed for rapid acceptance checks of small bores in production and quality control. Hardened steel construction Complies with DIN 7162 standard Wear allowance on the Go side Diameter 3.5 mm precision Reliable checks for small bores The limit plug gauge is intended for fast, unequivocal go/no-go inspections in the workshop and at in‑process control stations. Manufactured to DIN 7162, the tool offers standardised dimensions for consistent interchangeability across gauges and fixtures. With a nominal diameter of 3.5 mm, the gauge pin provides a compact solution for verifying small internal diameters without the need for complex measuring setups, enabling straightforward acceptance decisions and reducing inspection time. Designed to maintain accuracy and lifetime Constructed from hardened steel, the gauge resists wear and mechanical damage during repetitive use, which secures measurement stability over many cycles. The specified wear allowance on the Go side compensates for gradual material loss at the contact zone: this means the initial pass/fail boundary is conservatively set so that the Go end remains reliable as the gauge accumulates wear, thereby extending the service life and reducing replacement frequency. Such design reduces process interruptions and supports predictable maintenance planning. Practical integration into production and inspection routines As a dedicated measuring pin, the device integrates easily into gauge sets, test benches and handheld Go/No‑Go routines; the compact geometry allows quick handling and minimal fixturing. The simple acceptance logic of a limit plug gauge shortens operator training and accelerates throughput in inspection loops, delivering measurable time savings. For specific application scenarios or assistance with fixture compatibility, Metav’s technical advisers can provide pragmatic recommendations tailored to production needs. For standard-compliant bore checks and tailored application advice, order the Filetta limit plug gauge G7 via Metav Werkzeuge or contact our Emmerich team at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS911.163 Manufacturer: Filetta Product: Limit plug gauge G7 Facts Diameter: 3.5 mm Standard: DIN 7162 Special features Material: hardened steel Wear allowance on the Go side Category: gauge pins / measuring pins FAQ What is the primary purpose of this limit plug gauge? The Filetta limit plug gauge G7 (MS911.163) is used for quick go/no-go inspections of small internal diameters to support fast acceptance decisions in production and quality control. Which standard does the gauge comply with? The gauge is manufactured to DIN 7162, ensuring standardised dimensions and compatibility with conventional metrology practices. What material is the gauge made from and why is that important? This limit plug gauge is made of hardened steel, which improves wear resistance and maintains functional tolerances during repetitive use. What does "wear allowance on the Go side" mean in practice? The wear allowance on the Go side means the Go end is dimensioned to allow a controlled amount of wear before it affects pass/fail decisions, extending the gauge’s usable life while preserving inspection reliability. Can this gauge be used on a shop floor for routine checks? Yes, the compact 3.5 mm gauge pin is suitable for routine shop‑floor Go/No‑Go checks and can be incorporated into simple test fixtures or handheld inspection procedures. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
3.5 mm Limit Plug Gauge With Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Take advantage of a robust inspection tool that combines hardened steel construction, DIN 7162 conformity and a built‑in wear allowance on the good side for reproducible pass/fail checks; order the gauge via Metav Werkzeuge or request advice from our consultants for specification alignment. Filetta Limit plug gauge MS911.205 — hardened steel, DIN 7162, Ø 3.5 mm The Filetta Limit plug gauge is a compact inspection gauge for verifying internal diameters to DIN 7162, engineered for repeatable go/no‑go checks in production and quality control environments Hardened steel construction DIN 7162 compliant Wear allowance on good side Compact inspection gauge Ø3.5 mm Consistent go/no‑go verification for production control The limit plug gauge delivers a straightforward, objective decision at the workstation by separating acceptable bores from non‑conforming ones. Made from hardened steel, the gauge resists deformation and keeps the acceptance limits stable over long series, which reduces false rejects and costly rework. Compliance with DIN 7162 provides a recognised reference for inspectors and supports consistent acceptance criteria in incoming, in‑process and final inspections. Traceability and measurement clarity reduce uncertainty Marked limits and a clear go/no‑go function speed up inspection throughput while keeping measurement uncertainty low. The integrated wear allowance on the good side accounts for gradual material loss at the contact face, extending the effective service life before recalibration or replacement is required. This pragmatic design choice maintains inspection reliability without adding complexity to routine checks. Durable design for workshop conditions and regular handling Robust material selection and a compact form factor make the gauge well suited to repeat handling on shop floors and inspection benches. The small diameter of Ø 3.5 mm is ideal for fine bores and small components where space is limited; its finish and hardness ensure resistance against surface damage and sticking, which otherwise compromise pass/fail clarity and slow down quality routines. Practical integration and procurement advantages Using a standardised limit plug gauge simplifies documentation and reduces training time for inspectors: the pass/fail logic is immediate and requires no interpretation of numerical tolerance stacks. The gauge is a maintenance‑friendly tool that supports steady production flow and predictable inspection intervals, enabling planners to focus on process improvements rather than ad‑hoc measurement disputes. For purchase enquiries, technical clarifications or to source complementary inspection tools from Filetta, contact Metav Werkzeuge for personalised guidance and reliable delivery from Emmerich. Technical data Article number: MS911.205 Name: Limit plug gauge (Grenzlehrdorne) Manufacturer: Filetta Numbers / Core technical data Diameter: 3.5 mm Standard: DIN 7162 Designs / Special features Material: hardened steel Special feature: wear allowance on good side FAQ What acceptance standard does this gauge follow? The limit plug gauge is manufactured to meet DIN 7162, ensuring that acceptance limits correspond with widely used industrial inspection criteria. Which material is used for the gauge body? The gauge is produced from hardened steel, which provides dimensional stability and abrasion resistance for routine use. How does the wear allowance affect inspection? The wear allowance on the good side compensates for gradual surface wear, prolonging the useful life of the gauge and keeping go/no‑go decisions consistent over time. Is this gauge suitable for small bore inspection? Yes, its Ø 3.5 mm size is designed specifically for small bores and fine components where compact inspection gauges are required. What is the SKU for ordering or referencing the product? Reference the article number MS911.205 when specifying or ordering the Filetta limit plug gauge. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
4 mm Limit Gauge Go/No-Go Wear Allowance, DIN 7162 - Filetta
The hardened construction and conformity to DIN 7162 ensure reproducible acceptance checks, while the clearly indicated wear allowance on the go side supports long-term reliability. Combine robust material choice with standardised dimensions for consistent go/no‑go inspection; order the limit plug gauge directly via Metav Werkzeuge or consult its specialists for application advice. Filetta limit plug gauge — hardened steel, DIN 7162 A Filetta limit plug gauge designed for rapid go/no‑go checks of internal diameters, providing workshop-grade repeatability and a marked wear allowance for ongoing inspection integrity. Hardened steel construction DIN 7162 compliance Precision ground measuring pin Wear allowance on go side Dependable acceptance testing with hardened steel and standard conformity The gauge is manufactured from hardened steel, a material choice that resists surface deformation and maintains form under frequent use, which supports reproducible pass/fail decisions in production control. Conformity with DIN 7162 gives a clear normative basis for dimensioning and tolerances, reducing interpretation variations during inspection. The nominal size of 4 mm makes this item suitable for small bores and fine mechanical assemblies; the compact form factor simplifies handling while retaining the stiffness required for repeatable verification. How the wear allowance improves long‑term measurement reliability A distinctive characteristic is the wear allowance on the go side, which compensates for gradual material loss on the acceptance face and prolongs the interval between regrinds or replacements. The measuring pin is precision ground to present a stable reference surface for routine checks, so bench operators can rely on quick go/no‑go decisions without extensive setup. This targeted design reduces scrap risk and supports consistent quality control processes in small‑part production or inspection stations. Practical use and integration into workshop routines Constructed for straightforward bench use, the plug gauge fits into common inspection workflows and is compatible with existing go/no‑go procedures. The compact gauge is easy to store and retrieve, and the robust finish minimises maintenance needs. For quality systems, the clear marking of the wear allowance aids traceability in service records and in planning maintenance cycles, helping to maintain throughput without unexpected measurement drift. Choose Filetta's hardened steel limit plug gauge for reliable go/no‑go control and contact Metav Werkzeuge in Emmerich for order placement or technical consultation by phone or e‑mail Technical data Article number: MS911.164 Type: limit plug gauge Size: 4 mm Material: hardened steel Standard: DIN 7162 Facts SKU: MS911.164 Manufacturer: Filetta Special features Wear allowance on go side Precision ground measuring pin Intended for internal diameter acceptance testing FAQ What is the primary application of this limit plug gauge? The Filetta limit plug gauge is intended for quick go/no‑go verification of internal diameters, providing a pass/fail reference for small bores and fine mechanical parts. How does the wear allowance affect service life? The marked wear allowance on the go side extends the usable life of the gauge by compensating for gradual wear, helping to delay regrinding or replacement while maintaining acceptance criteria. Is the gauge suitable for laboratory calibration or only shop use? Manufactured from hardened steel and finished by precision grinding, the gauge is appropriate for workshop inspection and routine quality control; calibration scope depends on the laboratory procedure chosen. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
4 mm Limit Gauge Pin Wear Allowance, Hardened Steel DIN 7162 - Filetta
Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance for consistent pass/fail decisions and extended service life. Order the limit plug gauge directly via Metav Werkzeuge or contact our consultants for specification advice. Limit plug gauge – Filetta, hardened steel, DIN 7162 The Limit plug gauge is a precision go/no-go inspection pin designed for fast dimensional checks of bores and fittings in production and quality control. Hardened steel construction Manufactured to DIN 7162 Wear allowance on the good side Reliable pass/fail checking for fast quality control A compact limit plug gauge provides a straightforward binary decision in inspection routines, turning measurement into an immediate pass or fail. The combination of DIN 7162 conformity and a hardened shaft ensures that the gauge meets recognised geometric and tolerance requirements, which reduces interpretation time in quality control and accelerates throughput on the shop floor. This approach lowers downtime created by uncertain measurements and supports reproducible, traceable inspection results. Built for longevity and repeatable results Constructed from hardened steel, the pin resists abrasion and maintains a stable measuring diameter over many cycles, so calibration intervals can be extended without compromising confidence. The included wear allowance on the good side compensates for normal surface degradation, preserving the functional limit for go checks and reducing the need for immediate replacement. For maintenance planning this translates into predictable lifecycle costs and less frequent tool changeovers. Easy integration into workshop inspection processes Compliance with DIN 7162 means the gauge integrates cleanly into existing inspection plans and can be referenced in control documentation and reports. The simple geometry and compact design facilitate handheld use or fixture mounting, enabling quick comparison checks during in-process inspection or final quality control. The instrument functions as an efficient screening tool before more detailed metrology is applied, saving time while keeping measurement risk low. Suited applications and practical advantages Ideal for routine bore verification and acceptance testing, the gauge is suited to mechanical engineering, component assembly and finishing operations where fast, reproducible decisions are required. The small footprint of the pin makes it convenient in tight work stations and on assembly lines, while the robust material and standardised manufacture support long-term reliability. Where quick verification is needed, the plug gauge acts as a dependable first check. For DIN‑compliant limit gauging and practical advice from our Emmerich quality filter, contact Metav Werkzeuge to order Filetta limit plug gauges or to discuss application-specific recommendations: info@metav-werkzeuge.com / +49 2822 7131930. Technical data Article number: MS911.206 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Measurements Size: 4 mm Special features Wear allowance on the good side Category: Gauge pins / plug gauge Application: Pass/fail inspection of bores FAQ What is the primary purpose of this limit plug gauge? The limit plug gauge is intended for quick pass/fail verification of bore diameters and mating features during production and final inspection. Which material is used for the gauge? The Filetta limit plug gauge is made from hardened steel to ensure wear resistance and dimensional stability. Does the gauge comply with any standards? Yes, the gauge is manufactured in accordance with DIN 7162, ensuring standardised geometry and tolerance handling. What size does this article cover? This item is specified with a size of 4 mm and is listed under article number MS911.206. How does the wear allowance affect inspection? The built-in wear allowance on the good side maintains the effective go condition as the surface experiences normal abrasion, thus extending service life while preserving reliable go/no-go decisions. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
4.5mm Limit Plug Gauge Wear Allowance On Good Side, DIN 7162 - Filetta
Reliable DIN 7162 conformity and hardened steel construction give reproducible go/no-go checks; the built-in wear allowance on the good side extends service life. Take advantage of precise inspection, simple handling and long-term durability — order directly via Metav Werkzeuge or consult our specialists for tailored advice. Limit gauge pin MS911.207 — hardened steel, DIN 7162 (Ø 4.5 mm) The Limit gauge pin is a hardened-steel inspection pin designed for rapid go/no-go verification in workshop and production environments. Hardened steel construction, DIN 7162 compliant Diameter 4.5 mm for accurate limit checks Wear allowance on the good side to extend life Compact design for bench and fixture inspection Repeatable checks for fast quality decisions The limit gauge pin MS911.207 provides a straightforward method for pass/fail inspection that reduces decision time on the shop floor. Manufactured to DIN 7162, the pin’s hardened steel body maintains dimensional stability during repeated engagement, which supports consistent repeatability of go/no-go results. Using a simple plug-style verification avoids time-consuming measuring steps, improving throughput and lowering the cost of quality control across batches. Longer service life with controlled wear A decisive benefit of this inspection pin is the wear allowance on the good side, which compensates for material loss at the contact surface and preserves the calibrated function of the gauge for longer. The hardened finish resists surface damage while the allowance provides a controlled end-of-life margin, making maintenance planning predictable. This combination of durability and planned wear supports lower replacement frequency and steadier measurement confidence in production environments. Practical integration into standard inspection workflows Compact and purpose-built, the pin is suitable for quick checks in assembly, jig inspection and incoming goods control where clear go/no-go outcomes are required. The Ø 4.5 mm size fits small bores and fixture interfaces without complex setup, allowing inspectors to focus on throughput rather than instrument adjustment. The straightforward geometry and compliance with recognised standards make the pin an efficient addition to regulated inspection procedures and routine quality checks. Choose the Filetta limit gauge pin for DIN 7162-compliant checks and contact Metav Werkzeuge for fast delivery from Emmerich or expert advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS911.207 Name: Limit gauge pin Brand: Filetta Standard: DIN 7162 Key measurements Diameter: 4.5 mm Materials & special features Material: hardened steel Special feature: wear allowance on the good side Application: go/no-go inspection and limit checking FAQ What standard does this gauge pin follow? The Filetta limit gauge pin MS911.207 is manufactured to DIN 7162, ensuring conformity with widely recognised inspection practices. Which material is used for the pin and why does it matter? The pin is made from hardened steel, chosen for its resistance to wear and ability to retain dimensional stability under repeated use. How does the wear allowance affect inspection intervals? The wear allowance on the good side provides a predefined material margin, allowing predictable replacement scheduling and extending usable service life before a new gauge is required. For which inspection tasks is this pin intended? It is intended for rapid go/no-go verification of small bores and fixture interfaces, making it suitable for bench checks, assembly control and routine production inspections. Is the pin suitable for automated fixtures or only manual checks? Its compact, standard geometry allows use in manual inspection and integration into simple fixtures; suitability for automation depends on fixture design and handling requirements. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
4.5mm Limit Plug Gauge Wear Allowance, DIN 7162 - Filetta
The combination of robust hardened steel, conformity to DIN 7162 and a precise 4.5 mm nominal size ensures reliable pass/fail checks and long service life for small-bore inspection tasks; order the limit plug gauge directly via Metav Werkzeuge or consult our technical advisors for application-specific guidance. Limit plug gauge G7 – 4.5 mm, hardened steel by Filetta The Limit plug gauge G7 is a compact inspection pin designed for rapid go/no‑go acceptance testing of holes and bores in production and quality control settings. Hardened steel construction Conforms to DIN 7162 tolerance 4.5 mm nominal diameter Wear allowance on the go side Precision checks that speed up inspection A dedicated plug gauge built to DIN 7162 provides a straightforward, traceable method for go/no‑go assessment. The gauge’s 4.5 mm nominal size and G7 designation make it suitable for small-diameter bores where repeatable acceptance criteria are required. As a limit gauge, it converts geometric requirements into a tactile pass/fail verdict, reducing interpretation time during routine checks. The hardened construction maintains the calibrated profile over repeated use, supporting consistent process decisions and fewer downstream reworks. Robust design that reduces maintenance intervals Manufactured from hardened steel, the gauge resists premature wear in standard workshop environments, while the integrated wear allowance on the go side provides an engineered margin to extend useful life without compromising measurement integrity. This design choice lowers the frequency of replacements and conserves inspection resources, which translates into reduced process interruptions and predictable tooling budgets. The simple, single‑feature function of the instrument makes it a durable choice for shop‑floor verification and repetitive production control. Practical procurement and workshop integration The compact format and clear specification—listed under SKU MS911.165—enable easy stock management and fast identification in procurement systems. As a standardised acceptance tool, the plug gauge fits into established quality routines and can be used alongside other control artefacts to document conformity. Choosing a gauge from a recognised supplier supports traceability and aligns with systematic inspection plans; Metav’s distribution and inventory handling further simplify replenishment and selection for industrial and trade customers. Contact Metav Werkzeuge in Emmerich for availability and application advice on the Filetta limit plug gauge MS911.165 and to arrange delivery or technical consultation Technical data Article number: MS911.165 Material: hardened steel Nominal diameter: 4.5 mm Standard: DIN 7162 Facts Product type: limit plug gauge Designation: G7 Category: Gauges; Pin gauges Special features Wear allowance on the go side Compact inspection pin for small bores Suitable for routine go/no‑go acceptance testing FAQ What is the intended use of this limit plug gauge? The Filetta limit plug gauge MS911.165 is intended for quick go/no‑go checks of small bores to verify dimensional conformity to a specified tolerance class. How does the wear allowance affect service life? The built‑in wear allowance on the go side delays rejection due to normal surface wear, extending the practical lifetime of the gauge while maintaining reliable pass/fail decisions. Is the gauge suitable for use on finished components in production? Yes, the hardened‑steel construction and conformity to DIN 7162 make this limit plug gauge suitable for routine inspection of finished parts on the production line. Can this gauge be used for calibration or measurement recording? As a go/no‑go limit gauge, it serves as a conformity check rather than a measuring instrument for recorded dimensions; traceable gauge records should be maintained per internal quality procedures. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
5 mm Limit Go/No-Go Pin Gauge With Wear Allowance, DIN 7162 - Filetta
Combine hardened steel construction, conformity to DIN 7162 and a defined wear allowance on the good side to ensure reliable, repeatable checks of internal diameters. Order the limit plug gauge directly via Metav Werkzeuge or consult our specialists for batch requirements and inspection planning. Filetta Limit Plug Gauge MS911.208 — Hardened steel, DIN 7162 A Filetta limit plug gauge designed for straightforward verification of internal diameters in production, inspection and toolmaking environments. Hardened steel construction DIN 7162 conformity Wear allowance on good side Durable design for consistent inspection results The gauge pin is manufactured from hardened steel, giving a robust contact surface that resists deformation and extends service life under frequent use. Conformity with DIN 7162 ensures dimensional consistency between batches, which supports reproducible measurement routines on the shop floor. The supplied wear allowance on the good side is a defined margin that permits planned replacement or reconditioning before the gauge falls outside acceptable limits, helping to maintain process stability. Efficient application in production and quality control As a compact limit plug gauge, this tool allows rapid Go/No‑Go style checks of bore diameters without elaborate set‑ups. The simple geometry makes inspection fast and unambiguous: a correct fit confirms compliance, while a no‑fit indicates corrective action is required. For assembly lines and first‑article inspections the gauge provides a quick, objective pass/fail criterion that reduces downstream rework and supports lean quality processes while keeping handling straightforward for operators. Planning for traceability and maintenance Each item is identified by the article number MS911.208, which supports clear inventory and inspection records. The combination of a hardened contact surface and the specified wear allowance aids maintenance scheduling: gauges can be tracked for accumulated wear and replaced before causing measurement uncertainty. The material and standard reference also ease procurement and cross‑checking with technical drawings, making the component a dependable: repeatable reference for routine internal‑diameter verification. Choose Filetta limit plug gauges for dependable internal‑diameter control — contact Metav Werkzeuge in Emmerich for batch quotations and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: MS911.208 Brand: Filetta Material: hardened steel Standard: DIN 7162 Size: 5 mm Special note: wear allowance on the good side Core specifications Diameter: 5 mm Special features Hardened steel construction Wear allowance on the good side Conforms to DIN 7162 Category: limit plug gauge / gauge pin FAQ What is the primary purpose of this limit plug gauge? The Filetta limit plug gauge MS911.208 is intended for rapid verification of internal diameters, providing a straightforward Go/No‑Go style check in production and inspection contexts. Which material and standard apply to the gauge? The gauge is made from hardened steel and manufactured to meet DIN 7162, ensuring dimensional stability and industry‑recognised conformity. How should wear allowance on the good side be interpreted? Wear allowance on the good side denotes a planned margin by which the contact face may wear before the gauge is considered out of tolerance; it supports proactive maintenance and replacement scheduling. Can the gauge be used for routine assembly checks on the production line? Yes — the design of this limit plug gauge is suited to fast, repeatable pass/fail checks on bore diameters, making it useful for in‑line quality control and assembly verification. How is the item identified for inventory and traceability? The article number MS911.208 is used to track the item in inventory and inspection records, aiding traceability and maintenance documentation. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
5 mm Limit Pin Gauge Wear Allowance, DIN 7162 - Filetta
The combination of hardened steel construction, conformity with DIN 7162, and a clearly defined wear allowance on the good side ensures reliable, repeatable go/no-go verification and long service life; order this gauge pin directly via Metav Werkzeuge or consult the Metav team for application advice. Limit gauge pin G7, 5 mm — Filetta Limit gauge pin for precision go/no-go checks and wear assessment in workshop and inspection environments. Hardened steel construction Conforms to DIN 7162 Wear allowance marked on good side Consistent pass/fail inspection for production routines The robust hardened steel body provides a stable reference surface that resists deformation under repeated use, supporting repeatable inspection results when used for go/no-go checks. Conformity with DIN 7162 gives a recognised benchmark for dimensional behaviour and interchangeability, so inspection processes can be standardised across machines and shifts. This reliability reduces rework, streamlines quality control and shortens inspection cycles in a busy workshop environment. Visible wear allowance aids maintenance planning A clearly indicated wear allowance on the good side makes it straightforward to monitor gauge condition and schedule replacements before limits are exceeded. The marked allowance functions as an operational guide for maintenance teams and enables conservative assessment of gauge life without complex measurement procedures. This feature supports predictable tool management, helping to avoid unexpected inspection failures and maintain traceable measurement practice. Compact form for fixtures and tight spaces With a nominal size of 5 mm, the pin is suited to tight-fixture applications and small-bore verification tasks common in jigs and measuring arrangements. The compact diameter enables use as a precision locating element or measuring pin where access is limited, while the hardened finish sustains surface integrity under frequent contact. As a limit gauge pin, it delivers a focused solution for dimensional control of small components and fit checks within assemblies. For precision go/no-go control rely on Filetta quality—contact Metav Werkzeuge for availability, technical advice and secure delivery to your workshop Technical data Article number: MS911.166 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Measurements Nominal size: 5 mm Special features Wear allowance on the good side Category: measuring pins FAQ What is the intended use of this limit gauge pin? The limit gauge pin is designed for go/no-go verification and dimensional checks in workshop metrology; Filetta manufacture it to serve as a precise reference pin for small-bore and fit inspections. How does the wear allowance improve gauge management? A marked wear allowance on the good side provides a visual threshold for service life; when the allowance is reached the pin should be replaced to preserve measurement integrity. Is the product compliant with any standards? Yes, the pin complies with DIN 7162, ensuring standardised dimensional characteristics suitable for industrial inspection routines. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
5.5 mm Limit Gauge Pin With Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance on the Go side for dependable go/no-go checks in routine inspection. Order the Filetta limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Filetta Limit Plug Gauge G7 — Hardened steel, DIN 7162 A Limit plug gauge for rapid go/no-go verification of small bores during incoming inspection and process control. Hardened steel for long service life Complies with DIN 7162 inspection standard Wear allowance on the Go side Consistent dimensional checks for production quality The Filetta limit plug gauge delivers a compact, robust solution for fast pass/fail inspection of cylindrical bores. Manufactured from hardened steel, the gauge resists wear and maintains dimensional integrity under frequent use, which supports consistent precision in repetitive checks. Conformance with DIN 7162 ensures the gauge geometry and tolerances match established industrial expectations, simplifying documentation and traceability in standardised inspection routines. The incorporated wear allowance on the Go side extends service intervals by permitting controlled material removal while preserving functional acceptance limits. Practical benefits for shop-floor and inspection benches Designed for efficient routine use, this gauge streamlines the decision step between acceptable and non‑conforming workpieces with unmistakeable go/no-go feedback. The compact format suits bench inspection and dedicated control stations where speed and reliability matter; the simple plug engagement avoids time‑consuming measurements while reducing interpretation errors. As a tactile reference tool, the gauge complements digital instruments and micrometres by providing an immediate mechanical check that is quick to apply and straightforward to record in inspection logs. Durable design that lowers operational risk Material choice and standardised manufacture reduce uncertainty: hardened steel construction offers high wear resistance, while the standard compliance reduces the need for custom verification procedures. The wear allowance on the Go side is a practical feature that keeps the gauge serviceable for longer, lowering total cost of ownership and helping maintain process capability between calibrations. For workshops and production lines requiring reproducible go/no-go results, this gauge is a pragmatic component of a robust quality-control toolkit. Contact Metav Werkzeuge today to specify the right Filetta limit plug gauge (MS911.167) for the inspection tasks and to arrange delivery from Emmerich or further technical consultation Technical data Article number: MS911.167 Product: Limit plug gauge Material: Hardened steel Facts Size: 5.5 mm Standard: DIN 7162 Special features Wear allowance on the Go side FAQ What is the primary purpose of this limit plug gauge? The Filetta limit plug gauge MS911.167 is designed for quick go/no-go verification of small bores to determine conformity during incoming inspection and in-process checks. Which material is the gauge made from and why does it matter? Manufactured from hardened steel, the gauge resists wear and maintains dimensional stability, ensuring reliable pass/fail checks over extended use. Does the gauge follow a recognised standard? Yes. The gauge conforms to DIN 7162, which standardises geometry and tolerances for plug-style limit gauges used in industrial inspection. How does the wear allowance affect maintenance intervals? The built-in wear allowance on the Go side permits controlled degradation before the gauge reaches out-of-tolerance condition, extending usable life and reducing the frequency of replacement. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
5.5 mm Limit Plug Gauge Wear Allowance On Go Side, DIN 7162 - Filetta
Reliable inspection depends on durable, standardised tools: this limit gauge pin combines hardened steel construction with DIN 7162 conformity and a 5.5 mm nominal diameter to deliver repeatable checks and a measurable wear allowance on the good side. Order through Metav Werkzeuge or contact our consultants for procurement advice. Limit gauge pin — 5.5 mm, hardened steel, DIN 7162 A Limit gauge pin designed for precision go/no-go and bore checks in production and quality control, manufactured to DIN 7162 standards DIN 7162 standardised gauge pins Hardened steel for long service life 5.5 mm nominal diameter Wear allowance on the good side Repeatable inspection built on recognised standards Conformity to DIN 7162 ensures the pin fulfils established dimensional and geometrical requirements, which is critical for consistent go/no-go evaluation. The 5.5 mm nominal diameter is produced and controlled to the standard, so measurements performed with this plug remain comparable across production batches and inspection stations. Using a standardised pin reduces ambiguity in acceptance criteria and supports traceable quality processes, making it suitable for bench checks and inline verification. Engineered for durability and predictable life-cycle performance Constructed from hardened steel, the pin resists surface degradation during repeated insertion and withdrawal. The specified wear allowance on the good side provides a measurable margin that extends usable life while keeping inspection reliability intact; this allowance makes it clear when replacement is due before measurement uncertainty increases. Routine handling requires only basic cleaning and dry storage; these straightforward measures preserve the hardened surface and maintain conformity for longer, reducing downtime and replacement frequency. Practical benefit in workshop and inspection workflows Designed as a straightforward plug gauge, the component supports rapid verification of bore diameters, alignment checks and fit-control tasks where simple, repeatable decisions are needed. In small-series production and maintenance shops alike, the pin provides a fast, rational decision criterion—pass or fail—without elaborate equipment. The robust material and standard conformity make it a pragmatic choice for quality control points where reliable, easy-to-interpret results are the priority, helping to keep production moving with minimal inspection overhead. Discuss procurement and batch options for this Filetta limit gauge pin with Metav Werkzeuge in Emmerich; call +49 2822 7131930 or email info@metav-werkzeuge.com for guidance and delivery details Technical Data Article number: MS911.209 Category: Gauge pins / Pin gauges Manufacturer: Filetta Facts Nominal diameter: 5.5 mm Standard: DIN 7162 Material: hardened steel Special features Wear allowance on the good side Suitable for go/no-go and bore checks Conforms to DIN 7162 FAQ What nominal diameter does this gauge pin have? The Filetta limit gauge pin MS911.209 has a nominal diameter of 5.5 mm, produced to DIN 7162 tolerances. What material is used for the pin? The pin is made from hardened steel, giving it high surface resistance and durability for repeated inspection cycles. How does the wear allowance affect service life? The documented wear allowance on the good side gives a clear limit for replacement, extending usable life while maintaining reliable go/no-go decisions. Is the pin suitable for production-line checks? Yes, the MS911.209 plug gauge is designed for quick pass/fail checks and can be integrated into workshop and production inspection points. Which standard governs the geometry and tolerances of this pin? This gauge pin is manufactured to DIN 7162, which defines the relevant geometric and dimensional requirements. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
6 mm Limit Gauge Pin Wear Allowance, Hardened Steel DIN 7162 - Filetta
Combine robust hardened steel construction, conformity with DIN 7162 and a defined wear allowance on the go side for consistent pass/no‑go checks; order the limit plug gauge directly via Metav Werkzeuge or ask our consultants for application advice. Limit plug gauge MS911.210 — hardened steel, DIN 7162 (6 mm) The Limit plug gauge MS911.210 is a precision pass/no‑go plug intended for dimensional control of holes and bores in inspection and workshop environments Hardened steel construction Conforms to DIN 7162 standard Wear allowance on the go side Stable, standardised checks for production quality The MS911.210 offers a compact, repeatable method for verifying bore diameters. Made from hardened steel, the gauge resists deformation during routine use, which maintains measurement integrity across repeated cycles. Conformity with DIN 7162 provides clear acceptance criteria that align with common inspection procedures, simplifying documentation and helping to avoid interpretive errors on the shop floor. The 6 mm size is suited to small bore checking where consistency is essential. Predictable durability reduces inspection uncertainty A dedicated wear allowance on the "go" side extends the usable life of the gauge while preserving reliable acceptance limits. This planned allowance prevents sudden shifts in go/no‑go performance and supports predictable replacement intervals, reducing unexpected downtime. The hardened construction further improves resistance to surface wear and handling knocks, delivering a low‑maintenance inspection tool that remains trustworthy under frequent use. Practical integration into workshop processes Designed for straightforward adoption on inspection benches and in production lines, this plug gauge enables fast go/no‑go decisions without complex setup. The simple geometry and robust material make the device suitable for repetitive checks in mechanical workshops and small‑part assembly. For specification advice or assistance selecting complementary gauges, Metav's specialists provide guidance to ensure the chosen gauges match production tolerances and inspection routines. Contact Metav Werkzeuge for tailored inspection recommendations and to order the Filetta MS911.210 limit plug gauge directly from our Emmerich stock Technical Data Article number: MS911.210 Manufacturer: Filetta Type: Limit plug gauge Dimensions & Standards Size: 6 mm Standard: DIN 7162 Materials & Features Material: hardened steel Feature: Wear allowance on the go side Application: dimensional limit checking / plug gauge FAQ What is the intended use of this plug gauge? The MS911.210 limit plug gauge by Filetta is intended for quick pass/no‑go verification of bore diameters, providing a binary acceptance check for production and incoming inspection Which material is the gauge made from and why does that matter? This Filetta limit plug gauge is produced from hardened steel; the material choice increases wear resistance and preserves the gauge geometry under repeated use Does the gauge meet recognised standards? Yes, the MS911.210 is produced to the dimensions and tolerances defined by DIN 7162, ensuring compatibility with standard inspection procedures How does the wear allowance affect inspection results? The wear allowance on the go side of the Filetta MS911.210 allows predictable life planning and helps maintain consistent go/no‑go behaviour until scheduled replacement Which applications are suitable for a 6 mm plug gauge? A 6 mm limit plug gauge is suitable for small bore checks in mechanical workshops, component inspection and assembly processes where precise bore conformity is required Filetta: Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
6 mm Limit Gauge Plug, Wear Allowance On Good Side, Hardened Steel, DIN 7162 - Filetta
Taking advantage of hardened steel construction and DIN 7162 conformity, this limit plug gauge delivers consistent pass/fail inspection for small bores; its Ø 6 mm nominal diameter and wear allowance on the good side support reproducible measurements and predictable service intervals. Order the limit plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Filetta Limit Plug Gauge, Ø 6 mm, hardened steel (DIN 7162) A limit plug gauge for quick go/no‑go verification of internal diameters in production and inspection environments. Hardened steel construction for longevity Conforms to DIN 7162 standard Ø 6 mm nominal size for bore verification Includes wear allowance on the go side Reliable pass/fail inspection that saves time on the shop floor A compact verification tool designed for routine bore checks, the limit plug gauge offers immediate go/no‑go feedback without additional instrumentation. The hardened construction and standardised limits make it suitable for rapid in‑process checks and goods‑in inspections, reducing measurement cycles and minimising production delays. Using a simple tactile test, operators can maintain throughput while keeping quality gates intact — a practical solution where speed and repeatability matter. Robust materials and controlled wear for longer service life Manufactured from hardened steel, the gauge resists abrasion and stands up to repeated insertion into mating bores. The incorporated wear allowance on the go side provides a clear performance margin: wear can be monitored and replacement scheduled before limits are exceeded, preventing unexpected rejects. This feature translates into lower lifetime costs and predictable maintenance planning, particularly in high‑volume environments where tool longevity and consistent tolerance control are vital. Standards‑based accuracy for consistent production control Produced to DIN 7162, the gauge ensures compatibility with established inspection procedures and interchangeability across inspection stations. The defined geometry and limit definition simplify documentation in quality records and support conformity assessments during audits. As a single‑purpose limit gauge, it complements laboratory measuring equipment by offering a fast, unambiguous check that aligns with standardised inspection philosophies, improving overall process reliability. For DIN‑compliant limit plug gauges from Filetta, contact Metav Werkzeuge in Emmerich for expert advice and reliable supply of inspection tools Technical data Article number: MS911.168 Material: hardened steel Standard: DIN 7162 Nominal size: Ø 6 mm Facts Product type: limit plug gauge Application: pass/fail bore inspection Category: gauges / measuring pins Special features Wear allowance on the go side Simple tactile go/no‑go operation Suited for production and inspection environments FAQ What is the intended use of this limit plug gauge? This limit plug gauge is intended for quick go/no‑go verification of internal diameters in workshop and inspection settings; it provides immediate pass/fail assessment for bore checks. Which standard does the gauge comply with? The gauge is manufactured to DIN 7162, providing standardised limit geometry for consistent inspections. What material is used for the gauge and why does it matter? Made of hardened steel, the gauge offers wear resistance and a stable datum, which supports reproducible checks over many cycles. How does the wear allowance on the go side affect maintenance? The wear allowance gives a measurable margin for use: wear can be monitored and the gauge replaced before tolerances are lost, enabling planned maintenance and reducing downtime. Can this gauge be used for documented quality checks? Yes, the DIN‑compliant geometry and fixed limits make the gauge suitable for repeatable checks and inclusion in quality records. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
7 mm Go/No-Go Ring Gauge Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Benefit from a hardened steel construction, DIN 7162 standard compliance and a wear‑compensated 'go' face for consistent inspection results; order through Metav Werkzeuge or request specialist advice for integration into quality workflows. Limit plug gauge, 7 mm — hardened steel, DIN 7162 (Filetta) A limit plug gauge designed for rapid verification of internal diameters in production and inspection environments, combining standard conformity with a wear‑compensated go face for sustained accuracy Hardened steel construction Conforms to DIN 7162 Precision 7 mm diameter Wear allowance on the go face Consistent inspection reliability for serial use The compact design supports routine checks where repeatability matters: the hardened construction and standardised geometry ensure that each measurement delivers the same reference result, reducing ambiguous outcomes on the shop floor. Used as a go/no‑go reference, this gauge streamlines acceptance steps and shortens inspection cycles, which helps to lower rework rates and maintain production throughput without additional setup time. Durable design that preserves accuracy over time A dedicated wear allowance on the go face protects the reference dimension and extends service intervals; the result is fewer replacements and more stable process capability. The hardened steel body resists deformation and abrasion in continuous use, so calibration intervals remain conservative and the tool sustains usable tolerances across many inspection cycles, supporting predictable maintenance planning. Simple integration into quality systems and traceable documentation Built to DIN 7162, the gauge fits established go/no‑go procedures and can be referenced directly in inspection plans. Its compact diameter of 7 mm makes it suitable for confined bores and tight features commonly encountered in precision components. Traceability is straightforward when the gauge is recorded in quality documentation, enabling clear pass/fail decisions during incoming, in‑process and final checks. Choose Filetta's hardened, DIN‑compliant limit plug gauge for robust, repeatable gauging and contact Metav Werkzeuge in Emmerich for tailored advice and ordering—email info@metav-werkzeuge.com or call +49 2822 7131930 for fast technical support and supply coordination Technical Data Article number: MS911.211 Material: hardened steel Standard: DIN 7162 Diameter: 7 mm Facts Product type: Limit plug gauge Brand: Filetta Intended use: Internal diameter verification Special features Wear allowance on the go face Suitable for production and inspection gauging Compact geometry for confined bores FAQ What applications suit this limit plug gauge best? This limit plug gauge is intended for quick verification of internal diameters in production, incoming inspection and routine quality checks where a 7 mm reference is required. How does the wear allowance affect service life? The wear allowance on the go face preserves the reference dimension, so the gauge maintains usable accuracy longer and reduces the frequency of replacements. Is the gauge compliant with recognised standards? Yes, the tool is manufactured to DIN 7162, which ensures compatibility with established go/no‑go procedures and inspection documentation. What is the material and why does it matter? Made from hardened steel, the gauge offers abrasion resistance and dimensional stability under regular use, supporting consistent pass/fail decisions. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
7mm Limit Plug Gauge Wear Measurement Tip, Hardened Steel, DIN 7162 - Filetta
The combination of hardened steel construction, DIN 7162 conformity and a built‑in wear allowance on the good side provides reliable, repeatable limit checks with low life‑cycle cost; order this limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge G7 — 7 mm, hardened steel (Filetta) The limit plug gauge G7 is a precision limit gauge designed for rapid go/no‑go verification of bore diameters in production and inspection environments. Hardened steel for lasting dimensional stability Conforms to DIN 7162 for standardised tolerances Wear allowance on the 'good' side for reconditioning Ideal for rapid go/no‑go bore checks Fast, standards‑based inspection to keep throughput steady This limit gauge is manufactured from hardened steel and produced to DIN 7162, ensuring that each check delivers a clear, standards‑based decision: accept or reject. The compact pin form factor enables go/no‑go testing at production stations or in the quality lab with minimal setup time. By using a dedicated limit pin for a specific nominal diameter, process control becomes faster and less error‑prone than repeated measurement and calculation, improving overall line efficiency. Built for durability and easy maintenance The design incorporates an explicit wear allowance on the good side, which preserves functional limits after regrinding and extends service life. This intentional allowance means the pin can be reconditioned rather than replaced when surface wear appears, reducing total cost of ownership and downtime. The hardened surface resists abrasion in routine checks, while the clear distinction of the 'good' and 'no‑go' ends simplifies handling and reduces the risk of incorrect use. Practical fit for shop‑floor quality routines As a limit checking tool, the plug gauge integrates into visual and tactile inspection routines: a clear pass or fail removes ambiguity and accelerates decision loops. The small nominal diameter of 7 mm suits components in mechanical assemblies, hydraulic and pneumatic parts, and small‑bore workpieces where quick verification is required. Lightweight and compact, the gauge is easy to store at point of use and to include in inspection kits, helping standardise checks across operators and shifts. For procurement or technical clarification about Filetta limit plug gauges and availability via Metav Werkzeuge, contact our Emmerich team for tailored advice and stock information Technical data Article number: MS911.169 Brand: Filetta Nominal size: 7 mm Material: hardened steel Standard: DIN 7162 Facts Product type: limit plug gauge (go/no‑go) SKU: MS911.169 Typical application: bore diameter verification Format: pin / plug gauge Special features Wear allowance on the good side for regrinding Conforms to standardised tolerances (DIN 7162) Robust surface hardness for repeated checks FAQ What tolerance standard does this limit gauge follow? The limit plug gauge is manufactured to DIN 7162, which defines the dimensional and tolerance requirements used for standardised go/no‑go gauges. Can the gauge be reconditioned when worn? Yes, the built‑in wear allowance on the good side permits regrinding and requalification so the gauge remains serviceable over a longer period. Is this gauge suitable for quick shop‑floor checks of small bores? Yes, the 7 mm nominal diameter and pin format make the gauge well suited to rapid verification of small bores in production and inspection stations. Which materials is the gauge intended to inspect? The gauge is intended for dimensional verification of bores regardless of the workpiece material; material compatibility depends on the component, not the gauge itself. How is the pass/fail decision presented during inspection? The plug gauge provides an immediate pass/fail result: the go end should enter the bore, while the no‑go end must not, enabling unambiguous acceptance control. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
8 mm Limit Plug Gauge Wear Measurement Side, Hardened Steel DIN 7162 - Filetta
Combining hardened steel construction, DIN 7162 conformity and an integrated wear allowance on the good side, this limit plug gauge delivers repeatable go/no-go checks for inspection benches and production control; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge MS911.212 — hardened steel, DIN 7162 compliant A limit plug gauge for fast go/no-go checks in inspection and workshop environments, designed for robust repeatability and simple integration on control benches. Hardened steel to resist wear Compliant with DIN 7162 standard Wear allowance on the good side Ideal for go/no-go inspection Consistent results for routine inspection Made for straightforward limit gauging, this instrument provides a clear binary decision for hole acceptance. The DIN 7162 reference ensures the gauge meets established dimensional criteria, while the hardened steel construction reduces surface deformation during repeated use. For production lines and quality-control benches, the precise stop characteristics translate into fewer ambiguous measurements and a faster inspection cycle, improving throughput without sacrificing traceability. Long service life with built-in wear compensation The specified wear allowance on the good side compensates for gradual material loss at the gauge face, extending usable life and maintaining the integrity of acceptance limits. Because the working surfaces are hardened, abrasive contact produces less surface damage, so the interval between maintenance checks is lengthened. This durability lowers total cost of ownership for routine inspection equipment and contributes to stable production quality over time. Practical fit and traceability for workshop use The gauge is supplied in the nominal 8 mm size and is identified as MS911.212 for unambiguous ordering and stock control. Its compact geometry supports rapid manual checking of bores and through-holes on machined parts and assemblies. The simple go/no-go principle reduces operator training time and minimises interpretation errors; the result is a pragmatic measuring tool that integrates easily into incoming inspection, final control or shop-floor quality points. For availability and tailored advice on the Filetta limit plug gauge MS911.212 contact Metav Werkzeuge in Emmerich for fast supply and practical application support via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS911.212 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Nominal size: 8 mm Facts Type: limit plug gauge Function: go/no-go inspection Identification: MS911.212 Category: gauges / measuring pins Special features Wear allowance on the good side Robust hardened contact faces Suitable for workshop and inspection benches FAQ What is the primary use of this limit plug gauge? The limit plug gauge MS911.212 by Filetta is intended for go/no-go checks of bores during incoming inspection and final part verification. Which standard governs the dimensions of this gauge? The gauge conforms to DIN 7162, which defines the dimensional and tolerance requirements applied to limit plug gauges like MS911.212. What material is the gauge made from and why? This Filetta gauge is manufactured from hardened steel to provide durable contact faces that resist wear during repeated checking. How does the wear allowance affect inspection results? The wear allowance on the good side extends the service life of the gauge while keeping acceptance limits consistent, reducing the need for frequent replacement. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
8 mm Limit Plug Gauge Wear Side Measurement, Hardened Steel, DIN 7162 - Filetta
Take advantage of a hardened steel construction and compliance with DIN 7162 to secure reliable go/no-go checks and predictable tool life; the integrated wear allowance on the datum face ensures continued conformity during repetitive use — order the gauge via Metav Werkzeuge or contact our consultants for application advice. Limit plug gauge G7, Ø 8 mm — hardened steel, DIN 7162 The Limit plug gauge G7 is a hardened-steel checking pin designed for fast dimensional inspections of holes and bores in production and inspection environments, conforming to DIN 7162 for consistent limit testing. Hardened steel construction Complies with DIN 7162 tolerance standard G7 limit fit for quick go/no-go testing Wear allowance on datum face Precise limit testing for production control The gauge provides a simple, repeatable method for pass/fail acceptance of bores, reducing measurement time on the shop floor. Built to the DIN 7162 guideline and marked for a G7 fit, the checking pin delivers clear go/no-go decisions that streamline quality routines. Relying on a fixed limit geometry removes interpretation variability and supports faster throughput in batch checks, while the compact design suits manual handling at inspection benches or assembly stations. Robust construction that withstands routine use Made from hardened steel, the mandrel offers resistance to wear and deformation under repeated contact. The incorporated wear allowance on the datum face compensates for gradual material loss, extending usable life and maintaining conformity between inspections. This durability translates into less downtime for replacements and a lower total cost of ownership compared with softer or plated designs, especially where regular mechanical gauging is part of the process. Traceable specification and simple integration into QC workflows Identified as MS911.170 and produced by Filetta, the gauge is straightforward to document within inspection plans and work instructions. The uncomplicated go/no-go principle requires no electrical hookup or data output, so the tool integrates seamlessly into manual or semi-automated checks. The combination of standardised tolerance adherence and a rugged profile supports clear process control and easier training of operators, which benefits both small workshops and larger production environments. Contact Metav Werkzeuge in Emmerich for application guidance and to source the Filetta limit plug gauge MS911.170 for your quality-control needs Technical Data Article number: MS911.170 Name: Limit plug gauge G7 Manufacturer: Filetta Standard: DIN 7162 Facts Nominal size: 8 mm Fit/tolerance: G7 Special features Material: hardened steel Wear allowance on datum face Application: go/no-go checking of holes and bores FAQ What type of inspection is this gauge intended for? The limit plug gauge is intended for quick go/no-go acceptance tests of bores and holes, enabling clear pass/fail checks during incoming inspection or in-process control with the Filetta MS911.170. Is the gauge suitable for continuous production use? Yes, the hardened steel construction and the wear allowance on the datum face make the gauge suitable for repetitive use in production environments where frequent verification of bore conformity is required. Does the gauge conform to a recognised standard? The limit plug gauge is manufactured to the requirements of DIN 7162, ensuring compatibility with common metrology practices and documentation in quality systems. How is the gauge identified within inspection documentation? The tool should be recorded as Filetta MS911.170, described as a G7 limit plug gauge, 8 mm, which simplifies traceability in inspection plans and process control records. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
Ensure Accurate Fits with a Limit Plug Gauge
A Limit Plug Gauge is a simple and reliable tool for verifying the Internal Diameter of Holes against Specified Tolerance Limits. It is used to check whether a Bore Accepts the Go Side and Rejects the No-Go Side, ensuring Components meet Drawing Requirements in Production and Inspection. These Gauges support fast, repeatable checks that integrate seamlessly into Quality-Control Workflows.
How a Limit Plug Gauge Guarantees Fit and Function
The Limit Plug Gauge serves as a go/no-go reference for Assembly and Manufacturing Processes. By using a matched pair or double-ended Gauge, an Operator can assess whether a Bore lies within the Upper and Lower Tolerance without complex Measurement Devices. Typical Use Cases include Batch Inspection, Final Part Verification and In-Process Controls on CNC Lathes and Milling Machines.
Practical Advantages for Production and Quality Teams
Manufacturing Teams benefit from clear pass/fail results that reduce Downtime and speed up Decision Making. Routine use of Calibration and periodic recheck maintains Measurement Integrity and reduces Scrap Rates. For small Workshops as well as high-volume Lines, a Limit Plug Gauge delivers an efficient shortcut to confirm critical Fits.
What Makes These Gauges Effective in Real Conditions
Gauges are produced from Hardened Steel or Corrosion-Resistant Alloys and often receive a Ground Finish to ensure Long Service Life. The Design reduces Operator Influence: a Go fit should enter smoothly, a No-Go fit must not. Regular Calibration against Traceable Standards preserves Accuracy and supports Audit Requirements.
Key Features That Matter for Purchase Decisions
- Measurement Accuracy: Manufactured to tight tolerances for consistent results
- Material & Hardness: Hardened Steel or Stainless options for Durability
- Design Variants: Single-ended, Double-ended or Threaded versions for specific Tasks
- Ease of Use: Clear Go/No-Go indication for rapid Inspection
- Traceability: Calibration Certificates available to meet Quality Standards
Why Choosing the Right Gauge Improves Outcomes
Selecting a robust Limit Plug Gauge reduces Rework and ensures Component Compatibility during Assembly. Choosing a Gauge from a Respected Manufacturer enhances Reliability and simplifies Compliance with Customer and Regulatory Requirements. Periodic Service and Calibration keep Gauges within Specification and protect Product Integrity.
Quick Summary of Limit Plug Gauge Benefits
In short, the Limit Plug Gauge provides fast, unambiguous verification of Bore Tolerance, supporting consistent Quality and smoother Production Flow.
Final Recommendation and Support Offer
For reliable results, pick Gauges from established Manufacturers and schedule regular Calibration and Maintenance. If you need assistance choosing the right Gauge for your Application, our Technical Service can advise on Material, Size Range and Traceability Options to match your Quality Objectives.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com
FAQ
What is a limit plug gauge and how is it used? A limit plug gauge is a precision inspection tool used to check the internal diameter of holes against specified tolerances. It typically comes in go/no-go form to quickly verify whether a bore is within acceptable limits during quality control or production processes.
Can a limit plug gauge be calibrated and maintained for long-term accuracy? Yes, a limit plug gauge can be calibrated and maintained to ensure long-term accuracy. Regular calibration against traceable standards, proper cleaning after use, and storage in a protective case will help preserve measurement integrity.
How do I choose the right gauge tolerance for my application? Choose a gauge tolerance based on the engineering drawing specifications and the acceptable manufacturing variation. Consider the function of the part, fit requirements, and inspection frequency when selecting tolerance levels.
What materials are limit plug gauges typically made from and do they resist corrosion? Limit plug gauges are commonly made from hardened steel or stabilized alloys for wear resistance. For enhanced corrosion resistance, gauges may be coated or made from stainless materials depending on the supplier and application needs.